WAGO Modular IO System INTERBUS S Technical data

Modular I/O System
INTERBUS S
Manual
Technical description,
installation and
configuration
750-132
Version 2.2.2
ii • General
Copyright ã 1997-2001 by WAGO Kontakttechnik GmbH
All rights reserved.
WAGO Kontakttechnik GmbH
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax:
+49 (0) 571/8 87 – 1 69
E-Mail: info@wago.com
Web:
http://www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 – 5 55
Fax:
+49 (0) 571/8 87 – 4 30
E-Mail: support@wago.com
Every conceivable measure has been taken to ensure the correctness and completeness of this documentation. However, as errors can never be fully excluded we would appreciate any information or ideas at any time.
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally trademark or patent protected.
Modular I/O System
INTERBUS S
TABLE OF CONTENTS • iii
TABLE OF CONTENTS
Section 1:
Explanations
Section 2:
System Description INTERBUS S, Configuration,
Initial Starting, Diagnosis
Section 3:
Digital Inputs
750-400, 750-401, 750-402, 750-403, 750-405, 750-406,
750-410, 750-411, 750-408, 750-409, 750-412, 750-413,
750-414, 750-415
750-404
Section 4:
Digital Outputs
750-501, 750-502, 750-504, 750-516, 750-519
750-506
750-509
750-511
750-512, 750-513, 750-514, 750-517
Section 5:
Analog Inputs
750-452, 750-454, 750-482, 750-484
750-456,
750-461, 750-481
750-462, 750-469
750-465, 750-466, 750-486,
750-467, 750-468, 750-487, 750-488
750-472, 750-474
750-476, 750-478
Section 6:
Analog Outputs
750-550, 750-580
750-552, 750-554, 750-584
750-556
Section 7:
End- and Supply Terminal Blocks
750-600, 750-614, 750-616
750-601, 750-602, 750-609, 750-610, 750-611, 750-612,
750-613, 750-615
750-622
Section 8:
SSI Encoder Interface, Quadrature Encoder Interface
750-630, 750-631
Section 9:
RS232, TTY, RS485
750-650, 750-651, 750-653
Application in Explosive Environments
Approvals
Modular I/O System
INTERBUS S
iv • Notes
Modular I/O System
INTERBUS S
IMPORTANT!
For fast, trouble free installation and start up of the devices described in this manual, the
user should carefully read and follow the advice and explanations offered in this guide.
Explanation of symbols used:
The EXCLAMATION POINT symbol is used when:
a) improper handling could cause damage or destruction of the hard- or software
b) possible injury to persons when interfacing to dangerous process peripherals.
The FINGER symbol describes routines or gives advice for the efficient use of the
devices and optimization of the software.
FUNCTION The FUNCTION symbol refers to helpful notes which are necessary for the correct
function. These remarks should be followed.
The QUESTION MARK gives an explanation of terms.
The symbol BOOKS gives references to additional literature, manuals and data sheets.
The user is most important to us:
We place great importance on the quality and user-friendliness of our manuals. Should
you have any ideas or suggestions for improvement to the contents or graphical design,
we would be glad to receive your proposals.
Notice:
This manual, including all illustrations, is copyrighted. Any use of this manual beyond
the terms of copyright is not allowed. The reproduction, translation, or use of the
electronic and mechanical information is subject to written authorization from WAGO
Kontakttechnik GmbH. Violations will be prosecuted. WAGO Kontakttechnik GmbH
reserves the right of alternation and changes. All rights in case of granting patents or
protective rights are reserved to WAGO Kontakttechnik GmbH.
In the case of non-WAGO products no reference to patent rights is given, but their
existence is noted. The use of the products described in this manuals exclusively
intended for experts trained in PLC programming or electrical engineering, who are
familiar with the national electrical standards in force. WAGO Kontakttechnik GmbH
and overseas subsidiaries will not accept any liability for faulty actions and damages
which occur on WAGO or non-WAGO products when disregarding the information
given in this manual. Any change made in WAGO hard or software (for example entries
in a register) will result in an exclusion of liability on the part of WAGO Kontakttechnik
GmbH.
INTERBUS S / General information
1
:$*2Ç,2Ç6<67(0
Table of contents chapter 2
1 The WAGO I/O SYSTEM
1
2 Buscoupler Interbus S
2
2.1 Buscoupler-Hardware
2.2 Supply voltage - Electronics
2.3 Supply voltage - Field Side
2.4 Bus connection and station address
2
3
4
5
3 Enclosure and technical data
8
4 Interbus S
9
4.1 Interface Modules
4.2 Configuration software
9
10
5 Configuration of the fieldbus node in the master
controller
11
5.1 Identification code
5.2 ID Code for WAGO I/O System
5.3 IBS CMD Software
5.4 Example of application
11
12
13
19
6 Starting of operation and diagnostics
21
7 General conditions
23
7.1 Tansport and storing conditions
7.2 Mechanical and climatic conditions
7.3 Isolation, class of protection and degree of protection
7.4 Electromagnetic compatibility
7.5 Power supply
Use in Hazardous Environments
Approvals
INTERBUS S / General information
23
23
24
25
25
:$*2Ç,2Ç6<67(0
1
The WAGO I/O System
The WAGO I/O SYSTEM consists of various components which are capable of
providing modular and application specific fieldbus nodes for various fieldbusses.
I11.1 Setting up a fieldbus node with the WAGO I/O SYSTEM
General remark:
A fieldbus node consists in principle of a fieldbus coupler at the front end, a number of
special function modules and a termination module which is placed at the other end.
1 - Buscoupler
The Buscoupler forms the link between the fieldbus and the field devices with their I/O
functions. All control functions required for the faultless operation of the I/O functions
are carried out by the coupler. The connection to different fieldbus systems is
established by each of the corresponding Buscouplers, e.g. for PROFIBUS, INTERBUS
S, II/O LIGHTBUS, CAN, ModBus etc. In this way a change of the fieldbus system is
possible.
2 - Function modules
In the function modules, the incoming process data ais converted. Corresponding to the
different requirements, special function modules are available for a variety of functions.
There are digital and analog inputs and outputs and modules for special functions. The
modules are described in the following chapters.
3 - Termination module
A termination module is needed for faultless operation of the node. The termination
module is always placed as the last module in order to obtain a termination of the
fieldbus node. This module has no I/O function.
Interbus / Introduction
1
:$*2Ç,2Ç6<67(0
Assembly of the WAGO I/O System
All components of the system can be snapped directly on a carrier rail according to EN
50022 (DIN 35).
When snapping the analog or digital components onto the rail, no special sequence must
be observed. The secure positioning and connection of the individual function modules
and the coupler is provided by a snap-in system. This snap-in system provides automatic
interlocking onto the DIN rail assembly. It is always possible to remove a function
module or the Buscoupler from the assembly by pulling the orange pull-tab.
Please note, that the power supply of the field side as well as the data transmission are
interrupted. It has to be ensured that the interruption of PE will not put personnel or
equipment in danger.
With a CAGE CLAMP, conductors with a cross section of 0.08 to 2.5mm2 /AWG 18-14
can be connected. Vibration proof, fast and maintenance-free. You simply introduce a
screwdriver or an operating tool into the operating slot under the clamping unit. The
CAGE CLAMP spring is pressed down. You can now introduce the wire into the
clamping unit. Withdraw the operating tool and the conductor is automatically clamped.
Interbus / Introduction
2
:$*2Ç,2Ç6<67(0
The clamping force adjusts automatically to the conductor cross section. The flat
clamping face of the CAGE CLAMP spring presses the conductor against the current
bar without damage. Any deformation or movement of the conductor is compensated,
thus eliminating the risk of a loose connection. The contact point between conductor
and CAGE CLAMP is well protected against corrosive deterioration. This connection is
made fast and, furthermore, it is maintenance-free. There is no need for costly periodical
examination of the connections.
The supply modules of the WAGO I/O system are partly equipped with a fuse holder.
This fuse holder can be pulled out in order to break the circuit of the following modules.
To do so, you first have to insert a screwdriver into one of the slots on both sides in
order to pull out the front side of the fuse holder.
The front side now being hinged down makes it possible to remove or to insert the fuse.
After that, you lift up the front side again and push the fuse holder back into its original
position.
Interbus / Introduction
3
:$*2Ç,2Ç6<67(0
2
Buscoupler - INTERBUS S
2.1
Buscoupler - Hardware
Ill. 2: The INTERBUS buscoupler
The 750-304 Interbus coupler consists of two major electronic sub systems:
left side:
This housing contains the electronics for the coupling to the bus, the processor
and the fieldbus connection. (ill. 2.1)
right side:
This housing contains the DC to DC converter and power distribution for the internal K
bus, local processor and external 24 V DC connections to other discrete I/O modules.
Illustration 2.2 identifies the 24 V DC connection points to supply voltage to I/O
modules. Illustration 2.3 identifies the ground connection.
INTERBUS S / Buscoupler
3
:$*2Ç,2Ç6<67(0
2.2
Supply Voltage - Electronics
Ill. 3: Termination points for the power supply and the internal electronics
The nominal operating voltage of the Buscoupler and the control electronics in the
function modules is 5 V DC. The supply is connected to the first two CAGE CLAMPS
at the top of the coupler as seen in Ill. 3.
The 24 V DC supply voltage is generated by an internal voltage regulator (DC/DC
converter) and fed to the electronics (5 V DC). The electrical isolation of the external
bus system is made by utilizing an optocoupler.
Please note that the power supply for the control electronics in the function modules is
made automatically by the data contacts of the following module when it is snapped on
the assembly (ill. 3.1). The power supply to the attached I/O modules is provided by
gold-plated self-cleaning slide contacts. I f an attached module is taken out of the
existing configuration, the connection via the K bus is broken and the coupler is able to
detect this.
WARNING
If a module is taken out of the ex isting configuration, there may be undefined states.
You should disconnect the power supply when changing anything in the configuration.
INTERBUS S / Buscoupler
4
:$*2Ç,2Ç6<67(0
2.3
Supply Voltage - Field Side
Ill. 4: Termination points for the supply voltage - Field side
The connection of the supply
voltag e is electrically isolated from the internal
electronics. Two CAGE CL AMPS are alway s connected by a power contact. By this
way, the power supply is taken to different points of the configuration.
It is possible to supply the following at the termination points (Ill. 4):
Volts: 24 V DC - Amps: 10 A DC
WARNING!
120 and 230 V AC can only be supplied via modules 750-609, 750-611 and 750-612!
The supply modules which are permanently integrated on the buscouplers, can be
supplied with 24 V DC only. The current on the power contacts should be max. 10 A.
The voltage is automatically supplied when the function modules are snapped together.
Self-cleaning power jumper contacts (P.J.C.s) ensure safe connections (Ill. 4). Female
contacts (current supply) are integrated in the buscoupler and I/O housings. The male
contacts on the buscoupler and I/O housings supply the voltage to the I/O modules when
inserted together from left to right.
The ground (earth) contact makes first and breaks last conforming to electrical standards
and can be used as protective grounding.
Depending on the I/O function, some modules do not have P.J.C.s. It is important to
note this when assembling a node. Many modules require field side power, many do
not. Please review the circuit diagrams of the individual modules. An additional power
supply module may be necessary.
INTERBUS S / Buscoupler
5
:$*2Ç,2Ç6<67(0
When using the supply module 750-601/602, the field supply from the bus coupler is
interrupted. From that point a new power supply connection is necessary to provide DC
to any additional I/O modules.
WARNING!
The ground ( earth) field side contact should be disconnected when testing the isolation.
Otherwise the results could be wrong or even the module could be destroyed.
INTERBUS S / Buscoupler
6
:$*2Ç,2Ç6<67(0
2.4
Bus connection and station (node) address
Ill. 5: Bus connection
Fieldbus connection:
The Interbus interface is normally provided by D SUB connection according
Standard EIA RS485 for data transmission by wires.
Outgoing
D-SUB (OUT)
/DO
DO
/DI
DI
COM
PIN
cable
PIN
6
1
7
2
3
5
9
green
yellow
pink
gray
brown
commoning wire
commoning wire
6
1
7
2
3
to US
Incoming
D-SUB (IN)
/DO
DO
/DI
DI
COM
Table 1: Wire connection Interbus S
The connection point of the D SUB connector is lowered in such a way that after a
connector is installed placement in an 80mm high switchbox is possible.
INTERBUS S / Buscoupler
7
:$*2Ç,2Ç6<67(0
Configuration Interface
The configuration interface used for the communication with
WAGO-I/O-CHECK or for firmware upload is located behind the cover flap.
Configuration
interface
Fig. X-1: Configuration interface
g01xx06e
The communication cable (750-920) is connected to the 4-pole header.
Warning
The communication cable 750-920 must not be connected or disconnected
while the coupler/controller is powered on!
INTERBUS
7a
WAGO-I/O-SYSTEM 750
3 The Enclosure and Specifications
SYSTEM DATA:
Number of function modules
Number of I/O points
Transmission medium
max. bus length
Baud rate
INTEBUS S / Enclosure and specifications
750-304
750-324
256
on request
4096
on request
shielded Cu-cable (5 x 0.25 mm²)
400 m
500 kBaud
8
:$*2Ç,2Ç6<67(0
TECHNICAL DATA:
Number of function modules
Digital peripheral signals
Analog peripheral signals
Configuration possibility
Bus connection
Voltage supply
Input current
Internal current
Power jumper contacts
Maximum current supplied to K-Bus
for internal module use
Voltage power jumper contacts
Current power jumper contacts
Data contacts
750-304
750-324
dig.+analog
digital
64
32
256
64
32
--via PC or control
--2 D-SUB with protection against vibration
24V DC (-15%/+20%)
105 mA typ; 900 mA max.
85 mA typ.; 500 mA max.
400 mA
400 mA
blade / spring contact
slide contact, self-cleaning
1.75 A
on request
24 V DC
10A DC
slide contacts, 1.5 u hard gold-plated
self-cleaning
<1V with 64 wired special function modules
Polycarbonat, Polyamid 6.6
standard markers WAGO BR247/248
marker cards 8 x 47mm
CAGE CLAMP; 0.08mm2 -2.5mm2 /AWG 28 -14
any position
IP 20
500 V system / power supply
0°C...+55°C
51 x 65* x 100 (*from upper edge of the carrier rail)
Voltage drop via data contacts
Housing material
Marking
Wire connection
Mounting position
Type of protection
Isolation
Operating temperature
Dimensions (mm) W x H x L
INTEBUS S / Enclosure and specifications
9
:$*2Ç,2Ç6<67(0
Interbus S buscoupler with extended diagnostics 750-304/000-001
The Interbus S buscoupler with no. 750-304/000-001 has the possibility of extented
diagnostic functions. The technical data is the same as 750-304.
Different from the standard buscoupler, a word for diag nostic messages is put into the
input data process image and a word for the control of the diag nostic input is put into
the output data process image.
The maximum number of input and output modules is reduced by
the additional
diagnostic function because Interbus S transmits only 31 words of a process image.
Order of the diagnostic status word:
Bit of the 15 14 13 12 11 10 9
status word
error error code (s. table)
8
7
6
5
4
3
2
1
0
Channel Module
The error code is shown in the following table:
Error code
0
5
10
15
Description
unknown fault
defective fuse
broken wire
short circuit
Channel: This is the location for the fault input of a module. The counting is done in the
same way as numbering channels.
Module: This is the number of the module. Counting starts at the fieldbus coupler. The
first module attached to the coupler is module 0.
The diagnostic control word is for diagnostic actions. E.g. error messages can be cleared
in this way.
Order of the diagnostic control word:
Bit of the
15 14 13 12 11 10 9
control word
Actions
8
7
6
5
4
3
2
1
0
The actions are coded as follows:
Actions
0x00 (0)
0x01 (1)
0x80 (128)
INTEBUS S / Enclosure and specifications
Description
no action
Acknowledge diagnostic control word
Clears all error messages in the buffer
10
:$*2Ç,2Ç6<67(0
4
INTERBUS S
The Interbus S system (DIN 19245 part 1.2) is set up as a data ring with a central master
slave access procedure. All modules are understood as one log ical module. Each partner
receives data at its input and sends it to the nex
t partner at its output. There is no
addressing with a data frame because each partner knows by special control sig nals
(CLOCK, RESET, SELECT, CONTROL) where it is placed in the ring. So there is no
bus address. „Addressing“ is done via the physical place in the system.
Interbus S has the structure of a spatially distributed shift reg ister. Each cycle is input
and output at the same time. While the master g ives output data to the shift register, it
gets input data from the other end of the ring.
Each part of Interbus S has an ID register. This register keeps information about the type
of module, the number of I/O registers and the status and error information.
Interbus S has two general operating modes:
1) ID cycle
The interface module of all devices connected to the bus system reads out the ID register
in the ID cycle and builds up the process imag e with the aid of this information. The
cycle serves as an initialization and is carried out on request.
2) Data cycle
Within the data cycle all input data from the registers is transferred from all devices into
the master card (Host Controller) and all output data from the master card
(Host
controller) to the devices.
4.1 Master Cards (Scanners, Host Controllers)
The operation of the master is carried out in most cases via a central controller like a
PLC, PC or NC. Connection to the remote stations is made via master cards.
Common master modules are:
- Phoenix IBS S5 DCB/I-T
- Phoenix IBS S5 DSC/I-T
- Phoenix 100 CB-T
- Hilscher CIF 30 (via Synergetic Micro Systems in USA)
INTERBUS S / Interbus S
11
:$*2Ç,2Ç6<67(0
4.2 Configuration software
In order to make the connection between a PLC or PC and the remote stations, the
master cards must be configured with the individual station data.
For this, the following software packages are available. For example, the following are
available from Phoenix:
- IBS SYS SWT
- IBS CMD SWT
INTERBUS S / Interbus S
12
:$*2Ç,2Ç6<67(0
5
Configuration of the fieldbus node in the master
5.1 Identification Code
In the ID cycle which is carried out for the initialization of the Interbus system, the users
connected users are identified by their function and their byte length. The Interbus S
coupler identifies its length after being started in the initialization phase of the bus
modules and forms a corresponding ID code. To this effect each slave has an
implemented identification register (ID register) comprising 2 bytes.
A 2 byte wide data unit is called a word. It enables the encoding of 65536 different
states. In Interbus S, different types of users and data widths are called for the coding.
This enables the master to find out what type the device belongs to, which means for
example, recognizing either frequency inverters or I/O units, like the
:$*2Ç,2Ç6<67(0 In Interbus S the manufacturers of device types are not
recognized. The structure of the ID code is explained below as well as the significance
of the individual bits of the ID code.
The length information can be coded from 0 to 32 words:
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
messages
data width
class of user
type of user
data direction I, O, I/O
Table 2: Structure of the Interbus ID code
-In the ID registers, the device group is coded in the lowest value (L SB) 8 bits (ID 0 to
7).
-In the following 5 bits (ID 8 to 12), the data width is coded. The 3 bits with the highest
value (MSB) (ID 13 to 15) are used for manag ement functions. Via these bits, dy namic
fault messages are transferred during operation. These bits are not defined by
the
hardware.
INTERBUS S / Configuration
13
:$*2Ç,2Ç6<67(0
5.2
ID Code for WAGO I/O System
Due to the combined use of dig ital, analog and special functions on one fieldbus station
and with the given structure of the I nterbus ID codes, it is impossible to manag e with
one ID code.
The WAGO Interbus S buscoupler is identified as a digital slave with variable length!
ID-Code
dec, hex
1, 0x1
2, 0x2
3, 0x3
49, 0x31
50, 0x32
51, 0x33
Digital
Outputs
x
Digital
Inputs
Analog
Outputs
Analog
Inputs
x
x
x
-
x
-
-
x
x
x
[x]: ID code given []: is not possible
[-]: when mixed with digital
Table 3: ID codes for the WAGO Interbus S buscoupler
For the master, it is important to know how many data registers each user assigns in the
Interbus S system. If a user has, for example, 16 bits of input and 32 bits of output, he
assigns 2 words in the bus because there are 2 words of output. I n this case the hig her
value of data width is decisive. The data width is coded by the bits I D 8 to I D 12 as
shown in section 5.1.
The following table shows the reg ister widths depending on the function modules
connected to a WAGO Interbus S buscoupler.
Possible values for data length are::
Data length
Buscoupler Remarks
0 Words
x
1 Nibble
Busmaster supports only Generation 4.
1 Byte
Starting with SPS-Firmware 3.20 or PC-driver 2.0
3 Nibble
Busmaster supports only Generation 4
1 Word
x
3 Nibble
Busmaster supports only Generation 4
3 Byte
Starting with SPS-Firmware 3.20 or PC-driver 2.0
2 Words
x
5 Nibble
Busmaster supports only Generation 4
5 Byte
Starting with SPS-Firmware 3.20 or PC-driver 2.0
3 Words
x
4 Words
x
5 Words
x
6 Words
x, ab WF
Starting with SPS-Firmware 3.20 or PC-driver 2.0
7 Words
x, ab WF
Starting with SPS-Firmware 3.20 or PC-driver 2.0
8 Words
x
9 Words
x
10 Words
xx
Starting with SPS-Firmware 3.20 or PC-driver 2.0
12 Words
xx
Starting with SPS-Firmware 3.20 or PC-driver 2.0
14 Words
xx
Starting with SPS-Firmware 3.20 or PC-driver 2.0
16 Words
xx
Starting with SPS-Firmware 3.20 or PC-driver 2.0
24 Words
xx
Starting with SPS-Firmware 3.20 or PC-driver 2.0
32 Words
xx
Starting with SPS-Firmware 3.20 or PC-driver 2.0
[x]: is used [xx]: is used and firmware 3.20 or PC driver 2.0 or later is combined
INTERBUS S / Configuration
14
:$*2Ç,2Ç6<67(0
5.3 IBS CMD configuration software
In the following chapter the configuration package IBS CMD configuration software is
presented in short form. This procedure facilitates operation of the WAGO Interbus
buscoupler.
Further and specific information is given in the respective operating instructions of the
different software packages.
5.3.1 CMD Software Package
Please pay attention that the corresponding interfacing and the function extended should
be selected.
The following menu is obtained via the key OK and the password allocated at the
program installation.
Ill. 10: First menu configuration
This is the first menu for further configuration. From this point the configuration can be
made automatically or manually.
INTERBUS S / Configuration
15
:$*2Ç,2Ç6<67(0
1) Automatic configuration
Ill. 11: Automatic configuration
If the complete fieldbus system with all stations and the master interface is operational,
automatic configuration of the connected stations can be called up via the menu „bus
structure“. Then the communications are started automatically and the configuration is
determined and set.
INTERBUS S / Configuration
16
:$*2Ç,2Ç6<67(0
2) Ident code
Ill. 12: Insertion of the WAGO I/O System via the Ident code
For manual configuration, the menu item „ bus structure“ in the config uration screen
must be selected. You will then see Ill. 12.
The corresponding ID code of table 3 and the length of the process data channel must be
indicated in the selected submenu. The length is dependent on the module with the
largest data length.
INTERBUS S / Configuration
17
:$*2Ç,2Ç6<67(0
Ill. 13: Insertion of the ID code and the data length
With the finalization of the entries via the key OK, a menu for the definition of the user
will appear.
INTERBUS S / Configuration
18
:$*2Ç,2Ç6<67(0
Ill. 14: Description of user
INTERBUS S / Configuration
19
:$*2Ç,2Ç6<67(0
After all data has been entered and stored via OK, the station created with the WAGO
Interbus coupler is then integrated into the fieldbus system being set up.
This station is displayed via the bus structure that has now been integrated:
INTERBUS S / Configuration
20
:$*2Ç,2Ç6<67(0
5.4 Example of an application
Ill. 19: Example of an application
The Interbus S station is composed as follows:
Function module
1; Digital input
1; Digital Input
2; Digital Input
2; Digital Input
3; Voltage supply
4; Analog Input
4; Analog Input
5; Voltage supply
6; Digital Output
6; Digital Output
7; Digital Output
7; Digital Output
8; Digital Output
8; Digital Output
9; Digital Output
9; Digital Output
10; Voltage supply
11; Analog Output
11; Analog Output
12; Analog Input
12; Analog Input
13; Analog Output
13; Analog Output
14; Analog Input
14; Analog Input
15; Voltage supply
16; Digital Output
16; Digital Output
17; End module
Process image inputs
PI 32.0
PI 32.1
PI 32.2
PI 32.3
-----PI 20
PI 22
------
-----PI 24
PI 26
PI 28
PI 30
------
Table 5: Assignment of the process image
INTERBUS S / Configuration
21
------
Process image outputs
----------PI28.0
PI28.1
PI28.2
PI28.3
PI28.4
PI28.5
PI28.6
PI28.7
-----PI 20
PI 22
PI 24
PI 26
-----PI29.0
PI29.1
------
:$*2Ç,2Ç6<67(0
The addresses indicated in the table results from the master configuration started in the
basic address. By the internal structure of the Interbus coupler, the process image is
divided as follows:
O0
Output data
....
.....word orientated data
....
Ox
Ox+1 bit orientated data
Ox+y
Input data
I0
....
....word orientated data
....
Ix
Ix+1 bit orientated data
Ix+y
Due to this division, the first addresses allocated in the configuration are reserved for
the analog inputs and outputs. The counting direction is from left to right and starts with
the first analog channel next to the bus coupler.
Ill. 21: Definition inputs/outputs
INTERBUS S / Configuration
22
:$*2Ç,2Ç6<67(0
6
Buscoupler startup and troubleshooting
After configuration of the master connection and electrical installation of the fieldbus
node/station, operation of the system can begin.
After power to the B uscoupler and I /O modules has been applied, the B uscoupler
verifies all internal functions, components and the communication interface
by an
internal diagnostic routine. Then the function modules and the existing configuration is
determined. At the same time a hidden file is stored. It consists of an input and an output
area which is located on the fieldbus RAM of the log chip. During the power up phase
the ‘I/O ERR’ LED flashes with an increased frequency . After a faultless power up the
fieldbus coupler enters the state ‘fieldbus start’. The g reen LED ‘RUN’ indicates that
the Bus is operating normally.
In case of a fault the red ‘I/O ERR’ LED will continue flashing.
By counting the number and frequency of flashes the fault can be easily
identified
quickly and accurately. A varying number of flashes and frequencies defines the fault.
The table below describes the fault condition based on the counted number of ‘I/O ERR’
LED flashes.
,2581
,2(55
VHTXHQFH
3DXVH
2. Blinking sequence
3. Blinking sequence
error code
error argument
1
0
2
VHTXHQFH
3DXVH
VHTXHQFH
description
1
overflow of internal buffer for inline code
2
unknown data type
0
error in programmed process image
error
in
comparison
of
tables:
module
N
(programmed configuration), passive modules like supply
terminal blocks do not count
N (N>0)
3
0
modules have identified error in fieldbus commands
4
0
data error on fieldbus or fieldbus break at the coupler
4
N (N>0)
5
N
fieldbus break after module N
filedbus error in register communications with module N
error in INTERBUS-S configuration telegram
6
too lillte configuration data
0
error in 1st configuration byte
N (0<N<65)
Table 5: Diagnosis LEDs - on buscoupler
INTERBUS S / Startup
23
:$*2Ç,2Ç6<67(0
After elimination of the fault, the buscoupler can only be set to the normal working
condition by another POWER ON sequence.
The green I/O LED flashes when accessing the I/O modules internal data channels.
After being switched on, the buscoupler queries the configuration of the bus modules
but does not carry out a data exchange with the I/O modules. This means that the red I/O
LED will extinguish after a faultless startup. The green I/O LED will indicate when data
is being exchanged by the Interbus network.
Status and error diagnostics:
The fieldbus LEDs show the state of the bus system. The functions of Interbus S are
shown by the LEDs „READY“, „BA“, „RC“ and „RD“.
READY
BA
RC
RD
Meaning
on
off
off
off
Buscoupler ready
on
on
off
off
Fieldbus active; data exchange
on
off
on
off
incoming connection established
on
off
off
on
off
off
off
off
Field bus off
error in cable or master
no function ; no voltage
Help
search error in
cable or master
Table 7: Diagnostic LEDs - fieldbus
INTERBUS S / Startup
24
:$*2Ç,2Ç6<67(0
7
General conditions
This chapter describes the general conditions for error-free running of the
:$*2Ç,2Ç6<67(0
7.1
Transporting and storing conditions
The following declarations concern modules which are transported and stored in the
original package.
Condition
Free fall
Temperature
Relative humidity
allowed values
≤ 1m
-40° to +70° C
5 to 95% (without condensation)
7.2 Mechanical and climatic conditions
The modules of the :$*2Ç,2Ç6<67(0 are not allowed to be operated without
taking suitable actions
- in places with strong conditions e.g. very dusty rooms or corroding atmosphere
- in place with high concentrations of ionisation
The temperature should be in a range between 0° C and +55° C. The relative humidity
should be in a range of 5 to 95% (without condensation).
The modules should be placed horizontal for better heat dissipation.
The concentration of SO2 must be below 25 ppm with a relative humidity of < 75%. The
concentration of H2S must be below 10 ppm with the same humidity.
The mechanical conditions are given as sinusoidal oscillations.
Frequency range (Hz)
10 ≤ f < 57
57 ≤ f ≤ 150
continuous
0.0375 mm amplitude
0.5 g constant acceleration
sometimes
0.075mm amplitude
1 g constant acceleration
For stronger impulses and oscillations, the acceleration and the amplitude should be
reduced by suitable actions. The following table shows the type of test for the
mechanical conditions.
INTERBUS / General conditions
25
:$*2Ç,2Ç6<67(0
Test for
Oscillations
Impulse
7.3
Test sequence
Remarks
Test for oscillations Type of oscillation: sweep with a rate of
IEC 68, part 2-6
change of 1 octave per minute
10 Hz ≤ f < 57 Hz, const. amplitude
0,075mm
57 Hz ≤ f ≤ 150 Hz, const. acceleration
1g
period of oscillation: 10
sweep per axis in each of the 3 vertical
axes
Test for impulses
Type of impulse: half sinusoidal
IEC 68, part 2-27
Intensity of impulses: 15 g peak value,
11 ms maintenance time
route of impulses: 2 impulses in each of
the 3 vertical axes
Class of protection and degree of protection
The class of protection is IP2X (IEC 529), i.e. protection against touch with a standard
test object. There is also protection against solid bodies greater than 12 mm. There is no
special protection against water.
INTERBUS / General conditions
26
:$*2Ç,2Ç6<67(0
7.4
Electromagnetic compatibility
Method of measurement
Interference with narrow-band conducted
disturbance
Interference with impulse groups
Discharge of static electricity
Interference with electromagnetic fields
Interference field strength
Disturbance
EN 50082-2, A
EN 50082-2, B
EN 50082-2, B
EN 50082-2, A
EN 55011
These requests for electromagnetic compatibility are fulfilled by all modules of
:$*2Ç,2Ç6<67(0(except for 750-630 and 750-631).
7.5
Power supply
If non-stabilized power supply is used for the supply of the buscoupler, it must be
stabilized by a capacity ( 200 µF per 1 A load current).
For the :$*2Ç,2Ç6<67(0a filter module has been developed (288-824).
This module serves as a filter module for non-stabilized 24 V DC power supplies if the
specified voltage deviation is not met.
Reasons for the deviations may be voltage jumps in the primary circuit, overloads in the
secondary circuit or the switching of undampened inductances and capacitances.
7.6
Certificates
The modules of :$*2Ç,2Ç6<67(0 have passed the conformance test of UL .
Look for listing mark on product.
The Profibus coupler 750-301 and 750-303 are certified of PNO with Z 00241 and
Z00242.
The Interbus coupler 750-304 has passed the relevant tests in accordance with the
Interbus conformance requirements (number 111).
The DeviceNet coupler 750-306 has succesfully passed through the conformance test of
Open DeviceNet Vendors Association Europe.
INTERBUS / General conditions
27
:$*2Ç,2Ç6<67(0
Digital Inputs (24 V AC/DC, 120 V AC, 230 V AC, 48 V DC)
PN: 750-400...415
Technical description
The supply is applied by a series-connected termination to each I/O module for the
respective operating voltage. Power connections are made automatically from module to
module when snapped onto the DIN rail.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
All 2-channel digital inputs are 4-conductor devices allowing the direct connection of 4conductor sensors with the terminations V+, 0V, ground and signal.
The 4-channel digital inputs are suitable for the direct connection of two 3-conductor
sensors (V+, 0V, signal). The power distribution module 750-614 is available for the
connection of more sensors to V+ and 0V.
The modules 750-408 and 750-409 are low-side switching.
A 2-wire proximity switch can be connected to the modules 750-410 and 750-411.
RC filters are series-connected to the 5, 24 and 48 V versions for noise rejection and
switch debouncing. They are available with time constants of 3.0 ms and 0.2 ms.
The standard numerical assignment for bus operations is from left to right, starting with
the LSB. The positions of the different I/O modules in the configured node/station are
selectable by the user. A block type configuration is not necessary.
The Input module can be connected to all buscouplers of the WAGOÇI/OÇSYSTEM.
Digital Inputs 750-400...415
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of inputs
Input filter
Nominal voltage
Signal voltage (0)
Signal voltage (1)
Input current (internal)
Input current (field side)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm) WxHxL
Item Number 750Number of inputs
Input filter
Nominal voltage
Signal voltage (0)
Signal voltage (1)
Input current (internal)
Input current (field side)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
400
402
403
4
0.2 ms
3 ms
0.2 ms
24V DC (-15%/+20%)
-3V...+5V DC (std. EN 61131 Typ 1)
15V...30V DC (std. EN 61131 Typ 1)
2.5 mA max.
5 mA max.
5 mA typ.
500 V system/power supply
2
4
no address or configutation adjustment
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of carrier rail)
3 ms
2
401
405
406
2
10 ms
230 V AC
120 V AC
(-15%/+10%)
(15%/+10%)
0 V...40 V
0 V..20 V
AC
AC
79 V...1.1 UN 79 V...1.1
AC
UN AC
2 mA
6.5 mA typ. 4.5 mA typ.
4 kV system/power supply
410*
2
411*
3 ms
0.2 ms
24V DC (-15%/+20%))
-3 V ... +5 V DC (std.
EN 61131 Type 2)
11 V ... 30 V DC (std.
EN 61131 Type 2)
2.5 mA max.
8 mA typ.
500 V system/power
supply
2
no address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
*) 2 - wire proximity switch, current without load max. 2 mA
Digital Inputs 750-400...415
2
:$*2Ç,2Ç6<67(0
Item Number 750Number of inputs
Input filter
Nominal voltage
Signal voltage (0)
Signal voltage (1)
Input current (internal)
Input current (field side)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
Item Number 750Number of inputs
Input filter /
Conversion time
Nominal voltage
Signal voltage (0)
Signal voltage (1)
Input current (internal)
Input current (field side)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
Digital Inputs 750-400...415
408
4
409
412
2
413
3 ms
0,2 ms
3 ms
0,2 ms
24V DC (-15% / +20%)
48 V DC (-15% / +20%)
15 V...30 V DC
-6 V ... +10 V DC
-3 V...5 V DC
34 V ... 60 V DC
10 mA max.
5 mA max.
3.5 mA typ.
500 V system/power supply
4
2
no address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0,08 to 2,5 mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
414
4
0.2 ms
415
4
20 ms
5 V DC
24 V AC/DC
(-15%/+20%)
0...0.8 V DC
-3...+5 V DC
0...+5 V AC
2.4 V...5 V DC
11 ... 30 V DC
10 ... 27 V AC
5 mA
10 mA
50 µA typ.
7.5 mA DC
7.6 9.5 mA AC
500 V system/power supply
500V system/power
supply
50 V channel/channel
4
4
no address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0,08 to 2,5 mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
3
:$*2Ç,2Ç6<67(0
Counter modules
PN 750-404, 750-404/000-001, 750-404/000-002
750-404/000-003, 750-404/000-004
Up/Down Counter 100 kHz, 750-404
Technical Description:
Attention! The description that is in the I/O ring binder data pages (88-530/013-600
dated 7/96) is not correct. The bottom contacts are additional outputs.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The described configuration is counter with up/down input.
The following description is preliminary and is applicable to the factory configuration.
The counter module is able to run with all WAGOÇI/OÇSYSTEM bus-couplers
(except for the economy type).
Counter Module 750-404
1
:$*2⇓,2⇓6<67(0
Technical Data:
Item Number: 750Number of outputs
Output current
Number of counter
Input current (internal)
Nominal voltage
Signal voltage (0)
Signal voltage (1)
Switching rate
Output current
Counter size
Isolation
Bit width
Configuration
Operating temperature
Wire connection
Size (mm)WxHxD
Counter Module 750-404
404, 404/000-001
404/000-004
404/000-002
2
0.5 A
1
70 mA
24 V DC (-15% +20%)
-3V.....+5V DC
+15V...+30V DC
100 kHz
10 kHz max.
5 mA typ.
32 Bit
500 V system/power supply
32 Bit (8 Bit verification; 8 bit not used)
none, optional with software parameter
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
2
:$*2⇓,2⇓6<67(0
Organization of the in- and output data:
The counter begins processing with pulses at the CLOCK input. The changes from 0 V
to 24 V are counted.
The counter counts up, if the input U/D is set at 24 V. With an open circuit input or 0 V
the counter counts backwards.
The two bottom contacts each include another output. These outputs are activated
through bits in the control byte.
The control byte has the following bits:
Control Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
x
Set Counter
Block Counter
Output value at
output O2
Output value at
output O1
x
x
The status byte has the following bits:
Status Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
x
x
Counter is Counter is actual signal at
set
blocked
O2
Bit 2
Bit 1
Bit 0
actual signal
at O1
actual signal at
input U/D
actual signal at
input CLOCK
With the control and status-byte the following tasks are possible:
Set the counter: Put Bit 5 into the control byte. The counter with the 32 bit value is
loaded into output bytes 0-3. As long as the bits are set, the counter can stop and
information is stored. The ensuing data of the counter will be conveyed to the status
byte.
Blocking the counter: Bit 4 is set into the control byte, then the count process is
suppressed. Bit 4 in the status byte communicates the suppression of the counter.
Set the outputs: Bits 2 and 3 set the additional two outputs of the counter module.
The result of the counter is in binary.
Counter Module 750-404
3
:$*2⇓,2⇓6<67(0
An example:
The counter is set with “Set Counter” to the value 0x0000.0000
- 0X1X.XXXX, 0x00, 0x00, 0x00, 0x00 are carried over as output value
(carry over the control-byte and the new counter position),
-wait until the input value is 0X1X.XXXX, 0x00, 0x00, 0x00, 0x00
(the status-byte shows the loading feedback) ,
-carry over 0x00, 0x00, 0x00, 0x00, 0x00 as output value (release counter).
Wait for the first and further counting pulse
-the input value is XX00.XXXX, 0x00, 0x00, 0x00, 0x00 (no counting pulse received)
-the input value is XX00.XXXX, 0x00, 0x00, 0x00, 0x01 (1 counting pulse received)
-the input value is XX00.XXXX, 0x00, 0x00, 0x00, 0x02 (2 counting pulses received)
-.................
-the input value is XX00.XXXX, 0xFF, 0xFF, 0xFF, 0xFF (maximum counting position
is reached)
-the input value is XX00.XXXX, 0x00, 0x00, 0x00, 0x00 (a further counting pulse
causes an overflow)
-the input value is XX00.XXXX, 0x00, 0x00, 0x00 0x01, (a further counting pulse is
received)
Notes:
Counter Module 750-404
0x23 is a value in hexadecimal form
0101.1001 is a value in binary form
“X” is used if the value at this position is without any significance.
4
:$*2⇓,2⇓6<67(0
Counter with enable input 750-404/000-001
Technical description:
The counter module also can be ordered as counter with enable input (750-404/000001).
The counter begins processing with pulses at the CLOCK input. The changes from 0 V
to 24 V are counted.
The counter counts down if the input U/D is set at 24 V. With an open circuit input or 0
V the counter counts up.
The data format of the module is 4 bytes data and a control/status byte. The module is a
32 Bit counter. The ID Code os 180 (0xB4). The format of input and output data is the
same as 750-404.
The counter module is able to run with all WAGOÇI/OÇSYSTEM bus-couplers
(except for the economy type).
Counter Module 750-404
5
:$*2⇓,2⇓6<67(0
Peak Time Counter 750-404/000-002
Technical data
The counter module also can be ordered as peak time counter with 750-404/000-002.
This description is only intended for hardware version X X X X 0 0 0 1- - - -. The
serial number can be found on the right side of the module.
The counter begins processing with pulses at the CLOCK input. The changes from 0 V
to 24 V are counted.
The counter counts up if the input U/D is set at 24 V. With an open circuit input or 0 V
the counter counts backwards.
The two bottom contacts each include another output. These outputs are activated
through bits in the control byte.
The counter module is able to run with all WAGOÇI/OÇSYSTEM bus-couplers
(except for the economy type).
Counter Module 750-404
6
:$*2⇓,2⇓6<67(0
Organization of the in- and output data:
The counter begins processing with pulses at the CLOCK input for a special time span.
The time span is predefined as 10 s. The state of the counter is stored in the processs
image until the next period. After the recording the counting starts again at 0.
The activation of the counting and the synchronisation with the SPS is made by a
handshake in the control and status byte.
The end of thre counting period and thus the new process data is signaled by a toggel bit
in the status byte.
The control byte has the following bits:
Control Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
start of the
periodic
counting
0
Output value at
output O2
Output value at
output O1
0
0
The status byte has the following bits:
Status Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
counting
started
0
actual signal at
O2
actual signal
at O1
actual signal at
input U/D
Toggelbit for
end of the
record
Counter Module 750-404
7
:$*2⇓,2⇓6<67(0
Frequency Counter Module, 750-404/000-003
Status CLOCK
Status Gate
Q2
O1
O2
Q1
G
Clk
+E2
Clock
Gate
+ +
24V 24V
24V
- 0V-
0V
0V
power jumper
contacts
O1
O2
Q1
Q2
S
S
O1Q1
O2
Q2
750-404
000-003
Technical Description
The counter module 750-404/000-003 measures the period of the 24 V DC input sig nal
at the CL OCK terminal and converts it into a
corresponding frequency value. The
measurement is enabled if the GATE terminal is an open circuit input or 0V. To disable
processing, the GATE input is to be set to 24 V DC.
The terminals O1 and O2 work as binary outputs. Each output can be activated via
specific bits in the CONTROL byte.
The high states of the input and output channels are each indicated by a LED.
To recognize low frequency or near zero frequency signals, the maximum time between
two data updates is parameterizable.
Counter Module 750-404
8
:$*2⇓,2⇓6<67(0
Technical Data:
Item-No.: 750Supply Voltage
Input Voltage (low)
Input Voltage (high)
Input Current
Min. Pulse Width
Output Current
Voltage Drop
Frequency Range:
Integration time = 1 period
Integration time = 4 periods
Integration time = 16 periods
Measuring Error:
Range 0.1 - 100 Hz
Range 1 - 1000Hz
Range 10 - 10000Hz
Data Format:
Process Image
Internal Bit Width
Input Current (internal)
Operating Temperature
Wire Connection
Size (mm) WxHxD
404/000-003
24V DC (-15%/+20%)
-3V - 5V DC
15V - 30V DC
5mA typ. at 24V DC
10µs
0.5A (short circuit protection)
0.6V DC max. at 0.5A
0.1 100Hz, Resolution 0.001Hz
1 - 1,000Hz, Resolution 0.01Hz
10 - 10,000Hz, Resolution 0.1Hz (1Hz)
< ± 0.05%
< ± 0.05 %
< ± 0.2 %
5 Byte In- and Output
8 Bit CONTROL/STATUS + 32 Bit DATA
80mA max. at 5V DC
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of carrier rail)
Frequency Range:
Integration time = 1 period
Integration time = 4 periods
Integration time = 16 periods
Measuring Error:
Range 0.1 8000Hz
Range 0.25 - 32000Hz
Range 1
- 100000Hz
Counter Module 750-404
0.1 - 8,000Hz, Resolution 0.001Hz
0.25 - 32,000Hz, Resolution 0.01Hz
1
- 100,000Hz, Resolution 0.1Hz (1Hz)
< ± 1%
< ± 1.5 %
< ± 1.5 %
9
:$*2⇓,2⇓6<67(0
Functional description
The counter module acquires the time between one or more rising edges of the CLOCK
input signal and calculates the frequency of the applied signal.
The calculation and process imag e update are initiated every 1st, every 4th or every 16th
rising edge depending on the integration time selected via the CONTROL byte. The first
detection of a rising edge starts the cy clic period measurement and cannot provide a
valid frequency value. I n this case the module will send 0x
FFFFFFFFH for input
information. The same input value is returned when a static hig h or static low signal is
applied to the CLOCK input.
If there are no sig nal changes seen at the CL OCK input, the module can be forced to
update the process imag e after defined parameterizable time spans. I n this state the
module will send the non valid value 0xFFFFFFFFH too.
The following figures illustrate a process data cycle.
73
7
,1387)5(4
'$7$9$/,'
352&(66'$7$
[))))))))
''
''
[))))))))
''
'' ''
'' ,QSXW'DWD
73 I FXUUHQWSHULRG
7
0D[LPXPGDWDKROGWLPHSDUDPHWHUL]DEOH
Figure 2: Timing diagram for process data update sequence
(integration time = 1 period)
7
73
,1387)5(4
'$7$9$/,'
352&(66'$7$
[))))))))
''
''
[))))))))
'' ,QSXW'DWD
73 I FXUUHQWSHULRG
7
0D[LPXPGDWDKROGWLPHSDUDPHWHUL]DEOH
Figure 3: Timing diagram for process data update sequence
(integration time = 4 periods)
Counter Module 750-404
10
:$*2⇓,2⇓6<67(0
Structure of CONTROL and STATUS byte
CONTROL Byte
E
5(*B5(4 E
E
E
79'5(4
E
6(7B4
E
6(7B4
5(*B5(4 15':5
5(*B$
5(*B$
5(*B$
5(*B$
E
E
5$1*(B6(/
5$1*(B6(/
5(4
5(4
5(*B$
5(*B$
Bit
Description
5(*B5(4
5(*B$$
79'5(4
6(7B4
6(7B4
5$1*(B6(/5(4
5$1*(B6(/5(4
$FFHVVWRWKHUHJLVWHUVWUXFWXUHLVUHTXHVWHGEEFRQWDLQWKHDGGUHVVRIWKHUHJLVWHU
5HJLVWHUDGGUHVV
5HTXHVWWRFKDQJHWKHPD[LPXPWLPHZLWKRXWYDOLGGDWD
&RQWURO2XWSXW44RII4RQ
&RQWURO2XWSXW44RII4RQ
6HOHFWLRQRIWKHLQWHJUDWLRQWLPHDQGWKHUHSUHVHQWDWLRQRIPHDVXUHGIUHTXHQF\YDOXH
6HOHFWLRQRIWKHLQWHJUDWLRQWLPHDQGWKHUHSUHVHQWDWLRQRIPHDVXUHGIUHTXHQF\YDOXH
STATUS Byte
Counter 750-404
E
5(*B$&. E
E
67B*$7(
E
79'$&.
E
67B4
E
67B4
5(*B$&. 5(*B$
5(*B$
5(*B$
5(*B$
E
E
5$1*(B6(/
5$1*(B6(/
$&.
$&.
5(*B$
5(*B$
Bit
Description
5(*B$&.
5(*B$$
67B*$7(
79'$&.
67B$
67B$
5$1*(B6(/$&.
5$1*(B6(/$&.
$FNQRZOHGJPHQWWRWKHUHJLVWHUUHTXHVWEEFRQWDLQWKHDGGUHVVRIWKHUHJLVWHU
5HJLVWHUDGGUHVV
6WDWHRI*$7(LQSXW HQDEOHG GLVDEOHG
$FNQRZOHGJPHQW79'FKDQJHG
6WDWHRIRXWSXW4
6WDWHRIRXWSXW4
$FNQRZOHGJPHQWWR5DQJH6HOHFWLRQ)UHTXHQF\YDOXHVDUHYDOLG
$FNQRZOHGJPHQWWR5DQJH6HOHFWLRQ)UHTXHQF\YDOXHVDUHYDOLG
11
:$*2Ç,2Ç6<67(0
Structure of Input and Output data
The input data contain the CL OCK frequency as a binary value. The representation
depends on the RANGE_SEL bits in the CONTROL
byte. Even the method of
measuring is selected via these bits. The following table illustrates the different modes.
5$1*(B6(/
5$1*(B6(/
0HWKRGRIPHDVXUHPHQW
5HSUHVHQWDWLRQRIPHDVXULQJYDOXH
,QWHJUDWLRQRYHUSHULRG
,QWHJUDWLRQRYHUSHULRGV
,QWHJUDWLRQRYHUSHULRGV
,QWHJUDWLRQRYHUSHULRGV
)UHTXHQF\LQ+]
)UHTXHQF\LQ+]
)UHTXHQF\LQ+]
)UHTXHQF\LQ+]
Attention:
When a new frequency range is requested, the application has to wait for valid data until
the RANGE_SEL ACK bits contain the new frequency range. The maximum delay can
be calculated using the following formula
TDmax= 2 *
number of periods to be integrated
actual frequency
If the gate is enabled the input data contains the last valid frequency value. In this state
the application cannot request a new range.
The valid frequency
range stretches from 0.1 Hz (100D) up to
10 kHz (100000D).
To recognize static CL OCK signals, a watchdog timer is implemented. The default
value for the timer is 10s. The timer resets on every Power On.
The application is able to change the watchdog time during operation by using the
CONTROL byte.
This can be initiated by
writing the corresponding value into the output bytes
OUTPUT_DATA 1 a nd OUTPUT_DATA 0 be fore setting the TVD REQ bit in the
CONTROL byte.
The success of the parameter transfer is acknowledg ed by the module via the TVD ACK
bit in the STATUS information.
Attention:
The range of the watchdog timer stretches from 0 to 16383ms (0x 0000H to 0x3FFFH) in
steps of 1ms per digit.
Values which raise the permitted range of the watchdog timer are masked with 0x3FFF.
If the maximum possible frequency of the different ranges is raised (see the table with
maximum frequency ratings), the module will return the non valid data 0xFFFFFFFFH.
Counter 750-404
12
:$*2Ç,2Ç6<67(0
Organization of the in- and output data for Interbus
Output value of the control unit:
Byte
D15-D0
D31-D16
D47-D32
Identification
Control Byte
Output Byte 0
Output Byte 2
Output Byte 1
Output Byte 3
Input value of the control unit:
Byte
D15-D0
D31-D16
D2D47-D32
Identification
Status Byte
Input Byte 0
Input Byte 2
Input Byte 1
Input Byte 3
The input-bytes 0 to 3 form the 32 bit counter-output. In the output-bytes 0 to 3 the
initial value of the counter can be set.
Counter 750-404
13
:$*2Ç,2Ç6<67(0
Digital Outputs (Standard)
PN 750-501...504, 516, 519
Technical description:
The power supply is provided by a series-connected supply module for the respective
operating voltage. Power connections are made automatically from module to module
via the internal P.J.C.s when snapped onto the DIN rail.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
For the digital outputs (without diagnostic) four-conductor devices (V+; 0 V; signal;
ground) are standard. In case of 12 mm wide 4-channel digital output modules it is not
possible to use 4-conductor devices. 4 signal outputs, 2xV+ and 2x0V are provided.
All digital outputs are short-circuit protected.
In case of overloads a supply module with fuse (750-601) must be connected on the
line side to protect the output modules.
The module 750-516 is low-side switching. The indicated output values have been
determined for 100% duty cycle. However, in case of the 2 A versions it is possible to
operate single channels at higher load currents, however always verify that the total
current does not exceed 3.5 A per module. Example: 2x2A (standard); 1x3.0A; 1x0.5A
(total current: 3.5 A) The standard numerical assignment for bus operations is from left
to right, starting with the LSB. The positions of the different I/O modules in the
configured node/station are selectable by the user. A block type configuration is not
necessary.The Output module can be connected to all buscouplers of the
WAGOÇI/OÇSYSTEM.
Digital Outputs 750-501...504,516, 519
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of outputs
Kind of load
Nominal voltage
Output current (DC)
Current consumption
(internal)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
Item Number 750Number of outputs
Kind of load
Nominal voltage
Output current (DC)
Current consumption
(internal)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
*) low-side switching
Item Number 750Number of outputs
Kind of load
Nominal voltage
Output current (DC)
Current consumption
(internal)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
Digital Outputs 750-501...504,516, 519
501
502
2
resistive, inductive, lamps
24V DC (-15% / +20%)
0,5 A
2A
7 mA
500 V system / power supply
2
without address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0,08 to 2,5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
504
516*)
4
resistive, inductive, lamps
24V DC (-15% / +20%)
0,5 A
15 mA
500 V system / power supply
4
without address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0,08 to 2,5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
519
4
resistive, inductive, lamps
5 V DC
20 mA
16 mA
500 V system / power supply
4
without address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0,08 to 2,5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
2
:$*2Ç,2Ç6<67(0
Digital Outputs (Standard with diagnostics)
PN 750-506
Technical description:
The power supply is provided by a series-connected supply module for the respective
operating voltage. Power connections are made automatically from module to module
via the internal P.J.C.s when snapped onto the DIN rail.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
Using the digital outputs with diagnostic bit outputs (750-506) allows verification of the
I/O channel by the connected bus. Example: a short-circuit at the output or an open
circuit will set the appropriate error bit true indicating I/O failure. In this configuration
the function module includes 2 digital outputs and 2 separate digital inputs. For the
digital outputs with diagnostic four-conductor devices (V+; 0V; signal; ground) are
standard. All digital outputs are short-circuit protected.
In case of overloads a supply module with fuse (750-601) must be connected on the
line side to protect the output modules.
The standard numerical assignment for bus operations is from left to right, starting with
the LSB. The positions of the different I/O modules in the configured node/station are
selectable by the user. A block type configuration is not necessary. When using I/O
modules with diagnostics, the existing inputs must be considered accordingly in the
configuration of the Node/station. The Output module can be connected to all
buscouplers of the WAGOÇI/OÇSYSTEM.
Digital Outputs 750-506
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of outputs
Current consumption (internal)
Nominal voltage
Kind of load
Output current (DC)
Diagnostics
Current consumption (internal)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
506
2
15 mA
24V DC (-15%/+20%)
resistive, inductive, lamps
0.5 A
open circuit, overload
15 mA typ. + load
500 V system / power supply
4 in, 4 out
without address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of carrier rail)
The output bits control the state of the outputs.
function
Bit 3
no function
Bit 2
no function
Bit 1
controls O2
Bit 0
controls O1
Bit 0
diagnostics O1
The input bits show the state of the outputs.
function
output follows
output bit
no load is
connected
short circuit
power supply
too low*
Bit 3
diagnostics O2
Bit 2
diagnostics O2
0
0
Bit 1
diagnostics
O1
0
0
1
0
1
1
1
0
1
1
1
0
1
0
*The diagnostic bits refer to a hysteresis: If the voltage of the field side is higher than
11V in the falling circle, they are switched on. If the voltage is lower than 15,5 V in the
growing circle, they are switched off.
Digital Outputs 750-506
2
:$*2Ç,2Ç6<67(0
Digital Outputs (Solid State Relay)
PN 750-509
Technical Description
The power supply for the solid state relay module is connected by a series-connected
supply module for the respective operating voltage of 230 V. Power connections are
made automatically from module to module via the internal P.J.C.s when snapped onto
the DIN rail.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The power supply of the control side is not made via the power jumper contacts but
directly from the electronics. The respective output contacts of the switching element
are therefore always positioned at the field side. One termination point of these contacts
must be directly connected to the power supply. For the digital outputs four-conductor
devices (V+; 0V; signal; ground) are standard. All digital outputs are short-circuit
protected. In case of overloads a supply module with fuse (750-609) must be
connected on the line side to protect the output modules.
The standard numerical assignment for Bus operation is from left to right, starting with
the LSB. The positions of the different inputs in the configured station are via the user’s
choice. A block type assembly is not necessary. The Output module can be connected to
all buscouplers of the WAGOÇI/OÇSYSTEM.
Digital Outputs 750-509
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of outputs
Current consumption (internal)
Switching voltage
Switched current
Speed of operation
Volume resistance
Impulse current
Overvoltage protection
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
Digital Outputs 750-509
509
2
10 mA
0 V...230 V AC/DC
300 mA AC max.
1.65 ms typ., 5 ms max.
2.1 Ω typ., 3.2 Ω max.
0.5 A (20 s), 1.5 A (0.1 s)
>+/- 380 V (suppressor diode)
1.5 kV system / power supply
2
without address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
2
:$*2Ç,2Ç6<67(0
Pulsewidth Module
PN 750-511
Technical Description:
This description is for hard and software version X X X
number is displayed on the right side of the module.
X 2 B 0 2- - - - . The part
The initial pre-programmed base frequency is for 250 Hz. The resolution is 10 Bits and
the pulsewidth is modulated.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The following description is preliminary and is applicable to the factory configuration.
The pulsewidth output module 750-511 produces a binary modulated sig nal of 24 V.
The connection of the consuming device should be made via the „O“ and 0 V (common)
contacts of the module. The distribution of the 24 V DC is made via the power jumper
contacts. If galvanic isolation is desired, a new power feed via a 750-602 is required.
The PWM module can be connected to all buscouplers of the W AGOÇI/OÇSYSTEM
(except for the economy type).
Pulsewidth Module 750-511
1
:$*2Ç,2Ç6<67(0
Technical Data:
Part Number 750Number of outputs
Current consumption (internal)
Nominal voltage
Load type
Output current
Pulse frequency
Duty cycle
Resolution
Isolation
Configuration
Current Consumption (field
side)
Internal bit width per channel
Operating temperature
Wire connections
Dimension (mm)BxHxT
Preset Frequency
Pulsewidth Module 750-511
511
2
70 mA typical (internal)
24V DC (-15% +20%)
ohmic, inductive
0.1 A, short circuit protected
1 Hz...20kHz
0%...100% (Ton > 750 ns, Toff > 500 ns)
10 Bit max.
500 V system/power Supply
none, optional with software parameter
15 mA typ.
16 Bit Data + 8 Bit Control/Status
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
250 Hz Switching Frequency
2
:$*2Ç,2Ç6<67(0
Formation of on/off times
The programming of the on/off times occur with the resolution of 10 bits. The five LSB
of the 16 bit value can be zeros or one. The MSB will hold the sign and is preset to the
null state.
Duty Cycle
%
100
Increments
1023
Binary
Value
0111 1111 1111 1111
Hex.
7F FF
Dec.
32767
100
1023
0111 1111 1111 0000
7F E0
32752
50
511
0011 1111 1111 1111
3F FF
16383
25
255
0001 1111 1111 1111
1F FF
8191
12.5
127
0000 0001 0000 0000
01 00
256
0.1955
2
0000 0000 0100 0000
00 40
16
0.0977
1
0000 0000 0010 0000
00 20
32
0
0
0000 0000 0001 1111
00 1F
31
0
0
0000 0000 0000 0000
0
0
Table 1: Value Formation
24V
0%
24V
0V
24V
t
50%
t
Ill. 1: On/Off time relationships for Table 1.
Pulsewidth Module 750-511
0V
24V
0V
3
25%
0V
t
100%
t
:$*2Ç,2Ç6<67(0
Process Image Formation for Interbus
The process image of the 750-511 appears with 6 by tes of input and 6 by tes of output
data. The byte allocation for the preset duty cycle has the following modes of formation:
Output values:
D0
D1
D2
D3
D4
D5
Function
Control Byte
Output Byte 1
Output Byte 0
reserved
Output Byte 3
Output Byte 2
D0
D1
D2
D3
D4
D5
Function
Status Byte
Input Byte 1
Input Byte 0
reserved
Input Byte 3
Input Byte 2
Input values:
Out(In)put byte 0
Out(In)put byte 1
Pulsewidth Module 750-511
Low Byte
High Byte
4
:$*2Ç,2Ç6<67(0
Digital Outputs (Relay)
PN 750-512...514, 517
Technical description:
The power supply for the relay coils is not made via the power jumper contacts but
directly from the electronics. The respective output contacts of the switching element
are therefore always positioned at the field side.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
Version 1: non-floating (750-512)
The power supply is made via a series-connected supply terminal block for the
respective operating voltage. Power connections are made automatically from module to
module when snapped onto the DIN rail. One termination point of these contacts must
be directly connected to the power supply.
Version 2: isolated outputs (750-513, 750-514)
These I/O modules are not provided with integrated power jumper contacts. Care should
be taken to supply each isolated module with separate power supply connections.
The standard numerical assignment for Bus operation is from left to right, starting with
the LSB. The positions of the different inputs in the configured station are via the user’s
choice. A block type configuration is not necessary. The output module can be
connected to all buscouplers of the WAGOÇI/OÇSYSTEM.
Digital Outputs 750-512-514,517
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Type of contact
Current consumption (internal)
Switching voltage
Switching power
Switching current
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
Item Number 750Type of contact
Current consumption (internal)
Switching voltage
Switching power
Switching current
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
*ohmic load
1)
in design
Digital Outputs 750-512-514,517
512
513
2 make contacts
100 mA max.
30 V DC; 250V AC
60 W; 500 VA
cos ρ =0,4, L/Rmax=7 ms
max
2 A AC/ DC
4 kV system/power supply
2
without address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
514
2 changeover
70 mA max.
30 V DC; 125 V AC
30 W; 62.5 VA
0.5 A AC/ 1 A DC
1.5 kV system/power
supply
5171)
80 mA max.
250 V AC
1500 VA*
1 A AC
4 kV system/ power
supply
2
without address or configuration adjustment
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
2
:$*2Ç,2Ç6<67(0
Relays in the modules 750-512 and 750-513:
6ZLWFKLQJFDSDFLW\
10
@
$
>
W
Q
H
U
U
X
F
AC ohmic
DC ohmic
AC inductive, cosϕ=0.4
1
G
H
K
F
W
L
DC inductive
L/R=7ms
Z
6
0,1
10
100
1000
6ZLWFKHGYROWDJH>9@
7\SLFDOHOHFWULFDOOLIHWLPH
1,E+06
V
H
K
F
W
L
Z
V
I
R
U
H
E
30 V DC ohmic
120 V AC ohmic
250 V AC ohmic
30 V DC inductive,
L/R = 0.7ms
1,E+05
P
X
1
120 V AC inductive,
cosϕ=0.4
1,E+04
0,1
1
6ZLWFKHGFXUUHQW>$@
Digital Outputs 750-512-514,517
3
10
250 V AC inductive,
cosϕ=0.4
:$*2Ç,2Ç6<67(0
2 Channel Analog Inputs 0-20 mA / 4-20 mA
(Differential Inputs)
PN 750-452, 454, 750-482, 750-484
Technical Description
This description is only intended for hardware version X X X X 2 A 0 0 - - - -. The
serial number can be found on the right side of the module.
The input channels are differential inputs and they have a common ground potential.
The inputs are connected to +I and -I. The shield is connected to „S“. The connection is
made automatically when snapped onto the DIN rail.
These I/O modules are not provided with integrated power jumper contacts. The power
supply is made by the data contacts with a DC-DC converter. The modules can work
self-supporting.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The input module can be connected to all buscouplers of the :$*2Ç,2Ç6<67(0
(except for the economy type)
Analog Inputs 750-452, 454,482,484
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of channels
Nominal voltage
Current consumption
(internal)
Voltage
Signal current
Resistance
Resolution
Isolation
Conversion time
Bit width per channel
Operating temperature
Configuration
Wire connection
Dimensions
(mm)WxHxL
Analog Inputs 750-452, 454,482,484
452
2
70 mA
454
482
via system voltage
2
484
70 mA
35 V max.
0-20mA
4-20mA
0-20mA
4-20mA
50 Ω typ.
12 Bit
500 V System/Power supply
2 ms typ.
16 Bit Data, 8 Bit Control/Status
0°C....+55°C
none, optional via software parameter
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
2
:$*2Ç,2Ç6<67(0
The numerical format
All analog values will be shown in a unit numerical format. The resolution is 12 Bits.
The following table will explain the numerical format. (750-452, 454). The 3 least
significant Bits are not taken into account.
Input current Input current
0-20 mA
4-20 mA
20
20
0111 1111 1111 1000
Hex.
7F F8
Dec.
32760
10
12
0100 0000 0000 0000
40 00
16384
5
8
0010 0000 0000 0000
20 00
8192
2.5
6
0001 0000 0000 0000
10 00
4096
0.156
4.125
0000 0001 0000 0000
01 00
256
0.01
4.0078
0000 0000 0001 0000
00 10
16
0.005
4.0039
0000 0000 0000 1000
00 08
8
0
4
0000 0000 0000 0111
00 07
7
0
4
0000 0000 0000 0000
0
0
Analog Inputs 750-452, 454,482,484
Binary Value
3
:$*2Ç,2Ç6<67(0
The numerical format for Siemens
In addition to the full 16 bit indication of the measured value it is possible to use the
‘Siemens format’. The measured value is represented by the most significant 12 Bits.
The 3 least significant Bits are reserved for diagnostic and status purposes. (750-482,
484)
Input current
4-20 mA
Binary value
> 20
0101 0000 0000 0
20
0101 0000 0000 0
16
Hex.
Dec.
50 01
20481
000
50 00
20480
0100 0000 0000 0
000
40 00
16384
12
0011 0000 0000 0
000
30 00
12288
8
0010 0000 0000 0
000
20 00
8192
4.0078
0001 0000 0000 1
000
10 08
4104
4
0001 0000 0000 0
000
10 00
4096
4
0001 0000 0000 0
011
10 03
4099
Analog Inputs 750-452, 454,482,484
X : without meaning
F : short circuit or
F : open circuit
Ü : overflow
XFÜ
001
4
:$*2Ç,2Ç6<67(0
Input current
0-20 mA
Binary value
> 20
0100 0000 0000 0
20
0100 0000 0000 0
10
X : without meaning
F : short circuit
open circuit
Ü : overflow
XFÜ
001
Hex.
Dec.
40 01
16385
000
40 00
16384
0010 0000 0000 0
000
20 00
8192
5
0001 0000 0000 0
000
10 00
4096
2.5
0000 1000 0000 0
000
08 00
2048
1.25
0000 0100 0000 0
000
04 00
1024
0.625
0000 0010 0000 0
000
02 00
512
0.0976
0000 0000 0000 1
000
00 08
8
0
0000 0000 0000 0
000
00 00
0
If you have questions about the formatting of this data, please contact WAGO for
I/O System technical support.
Analog Inputs 750-452, 454,482,484
5
:$*2Ç,2Ç6<67(0
2 Channel Analog Inputs +/- 10 V
(Differential Inputs)
PN 750-456, 750-456/000-001
Technical Description
This description is only intended for hardware version X X X X 2 A 0 0 - - - -. The
serial number can be found on the right side of the module.
The input channels are differential inputs and they have a common ground potential.
The inputs are connected to +I and -I. The shield is connected to „S“. The connection is
made automatically when snapped onto the DIN rail.
These I/O modules are not provided with integrated power jumper contacts. The power
supply is made by the data contacts with a DC-DC converter. The modules can work
self-supporting.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The input module can be connected to all buscouplers of the :$*2Ç,2Ç6<67(0
(except for the economy type)
Analog Inputs 750-456
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of channels
Nominal voltage
Current consumption
(internal)
Overvoltage protection
Signal voltage
Resistance
Resolution
Isolation
Conversion time
Bit width per channel
Operating temperature
Configuration
Wire connection
Dimensions
(mm)WxHxL
456, 456/000-001
2
via system voltage (DC DC converter)
65 mA
35 V max.
+/- 10 V
570 kΩ
12 Bit
500 V System/Power supply
2 ms typ.
16 Bit Data, 8 Bit Control/Status
0°C....+55°C
none, optional via software parameter
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
Attention:
The value of the input signal should be in a range of 0V to 10V or even no signal.
Analog Inputs 750-456
2
:$*2Ç,2Ç6<67(0
The numerical format
All analog values will be shown in a unit numerical format. The resolution is 12 Bits
and the 3 LSBs are not taken into account. The following table will explain the
numerical format.
Input voltage
±10V
> 10 V
Status
0111 1111 1111 1111
Hex.
7F FF
Dec.
32767
10
0111 1111 1111 XXXX
7F FX
32760
0
5
0100 0000 0000 XXXX
40 0X
16384
0
2,5
0010 0000 0000 XXXX
20 0X
8192
0
1,25
0001 0000 0000 XXXX
10 0X
4096
0
0,0781
0000 0001 0000 XXXX
01 0X
256
0
0,0049
0000 0000 0001 XXXX
00 1X
16
0
0
0000 0000 0000 XXXX
00 0X
0
0
-2,5
1110 0000 0000 XXXX
E0 0X
57344
0
-5
1100 0000 0000 XXXX
C0 0X
49152
0
-7,5
1010 0000 0000 XXXX
A0 0X
40960
0
-10
1000 0000 0000 XXXX
80 0X
32768
0
< -10 V
1000 0000 0000 0000
80 00
32768
41
Analog Inputs 750-456
Binary value
3
42
:$*2Ç,2Ç6<67(0
The numerical format for Siemens
In addition to the full 16 bit indication of the measured value it is possible to use the
Siemens format. The measured value is represented by the most significant 12 Bits. The
3 least significant bits are reserved for diagnostic and status purposes. (750-456/000001).
Input voltage
±10V
Binary value
>10
0111 1111 1111 1
10
0111 1111 1111 1
5
X : without
meaning
F : short circuit
or
F : open circuit
Ü : overflow
XFÜ
001
Hex.
Dec.
7F F9
32761
000
7F F8
32760
0110 0000 0000 0
000
60 00
24576
2,5
0101 0000 0000 0
000
50 00
20480
1,25
0100 1000 0000 0
000
48 00
18432
0,0049
0100 0000 0000 1
000
40 08
16392
0
0100 0000 0000 0
000
40 00
16384
-2,5
0011 0000 0000 1
000
30 08
12296
-5
0010 0000 0000 0
000
20 00
8192
-7,5
0001 0000 0000 0
000
10 00
4096
-10
0000 0000 0000 1
000
00 00
8
<-10
0000 0000 0000 0
001
00 01
1
If you hve questions about the formatting of this data, please contact WAGO for
the I/O System technical support.
Analog Inputs 750-456
4
:$*2Ç,2Ç6<67(0
Input for PT 100
PN 750-461, 750-461/000-002, 750-461/000-003, 750-481
Technical description:
This description is only intended for hardware version X X X X 3 A 0 2 - - - -. The
serial number can be found on the right side of the module.
The described configuration is PT 100. The following description is preliminary and is
applicable only to the factory configuration.
The inputs are connected to +I and -I. The shield is connected to „S“. The connection is
made automatically when snapped onto the DIN rail.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
These I/O modules are not provided with integrated power jumper contacts. The power
supply is made by the data contacts with a DC-DC converter. The modules can work
self-supporting.
The PT100 module can be connected to all buscouplers of the
:$*2Ç,2Ç6<67(0 (except for the economy type)
Input for PT100 750-461, 481
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of inputs
Input current (internal)
Voltage supply
Sensor types
Wire connection
Temperature range
Resolution
Isolation DC/DC
Measuring current
Bit width per channel
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
Presetting
461, 481, 461/000-002, 461/000-003
2
65 mA
via system voltage
PT100, PT 200, PT 500, PT1000, Ni100, Ni120, Ni1000
2-conductor, 3-conductor (presetting)
PT: -200°C..+850°C Ni:-60°C...250°C
0.1°C over the whole area
400V system / power supply
0.5mA type
16 bits: data; 8 bits: control/status
none, optional via software parameter
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
3-conductor PT100
The function module 750-461 allows the direct connection of PT- or Ni-resistance
sensors. The module is suitable for 2- or 3-wire RTDs. Connection is made according to
the above wiring diagram.
Linearization is accomplished over the entire measurement range by a microprocessor.
The temperature ranges of the above listed RTD types is available to the user. The
temperature ranges of the sensors are represented with a resolution of 1 bit per 0.1° C in
one word (16 bits). Resulting from this, 0°C corresponds to the hexadecimal value 0000
and 100°C is 03E8 (dez.1000). Temperatures below 0° are represented in two’s
complement with a leading ‘1’.
The function module works in the defined temperature range for the PT100 sensors of
-200°C to +850°C. The voltage resolution is represented with 16 bits. An A/D
converter and processor converts the voltage value to a numerical value proportional to
the temperature of the selected resistance temperature sensor.
A short circuit or an interruption of the RTD wire is transmitted to the bus module and
indicated by the red error LED. The green LED identifies that the module is
communicating properly with the connected Buscoupler.
Input for PT100 750-461, 481
2
:$*2Ç,2Ç6<67(0
The numerical format
All temperature values will be shown in a unit numerical format. If the mode
‘DEFAULT’ is selected each bit corresponds to 0.1°C. The possible numerical range
refers to the standardized temperature range of the used sensors. The following table
will explain the numerical format on a preset PT100. In the third column the numerical
format for PT1000 (750-461/000-003) is explained.
Temperature
°C
Voltage
(Ohm)
>400
Voltage
(Ohm)
Binary Value
850
390.481
1384,998
100
138.506
25.5
Hex.
Dec.
0010 0001 0011 0100
2134
8500
1099,299
0000 0011 1110 1000
03E8
1000
109.929
1000,391
0000 0000 1111 1111
00FF
255
0.1
100.039
1000
0000 0000 0000 0001
0001
1
0
100
999,619
0000 0000 0000 0000
0000
0
-0.1
99.970
901,929
1111 1111 1111 1111
FFFF
-1
-25.5
90.389
184,936
1111 1111 0000 0001
FF01
-255
-200
18.192
1111 1000 0011 0000
F830
-2000
<18
1000 0000 0000 0000
8000
-32767
Table 1
Input for PT100 750-461, 481
3
:$*2Ç,2Ç6<67(0
The numerical format for 750-461/000-002
All temperature values will be shown in a unit numerical format. Each bit corresponds
to 0.1°C. The following table will explain the numerical format for 750-461/000-002.
Voltage
(Ohm)
10
0000 0000 0110 0100
Hex.
00 64
Dez.
100
100
0000 0011 1110 1000
03 E8
1000
200
0000 0111 1101 0000
07 D0
2000
300
0000 1011 1011 1000
0B B8
3000
400
0000 1111 1010 0000
0F A0
4000
500
0001 0011 1000 1000
13 88
5000
1000
0010 0111 0001 0000
27 10
10000
1200
0010 1110 1110 0000
2E E0
12000
Input for PT100 750-461, 481
Binary value
4
:$*2Ç,2Ç6<67(0
The numerical format for Siemens
In addition to the full 16 bit indication of the measured value it is possible to use the
‘Siemens format’. The measured value is represented by the most significant 12 Bits.
The 4 least significant Bits are reserved for diagnostic and status purposes. (750-481)
Temp.
°C
Ohm
Binary value
>400
1111 1111 1111 1
883
400
0111 1111 1111 1
560
300
266
X : without meaning
F : short circuit or
F : open circuit
Ü : overflow
XFÜ
001
Hex.
Dec.
FF F9
65529
000
7F F8
32866
0110 0000 0000 0
000
60 00
24576
200
0100 0000 0000 0
000
40 00
16384
0
100
0010 0000 0000 0
000
20 00
8192
-125
50
0001 0000 0000 0
000
10 00
4096
-185
25
0000 0101 0000 0
000
500
1280
-200
20
0000 0100 0000 0
000
400
1024
<-200
0
0000 0000 0000 0
001
1
1
If you have questions about the formatting of this data, please contact WAGO for
I/O System technical support.
Input for PT100 750-461, 481
5
:$*2Ç,2Ç6<67(0
Input for Thermocouple Modules
PN 750-462, 750-469, 750-462/000-XXX
Technical description:
This description is only intended for hardware version X X X X 2 A 0 1 - - - -. The
serial number can be found on the right side of the module.
The following description is preliminary and is applicable only to the factory
configuration.
The shield is connected to „S“. The connection is made automatically when snapped
onto the DIN rail.
These I/O modules are not provided with integrated power jumper contacts. The power
supply is made by the data contacts with a DC-DC converter. The modules can work
self-supporting.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The thermocouple module can be connected to all buscouplers of the
:$*2Ç,2Ç6<67(0 (except for the economy type)
Input for thermocouple modules 750-462,469
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of inputs
Voltage supply
Sensor types
Cold junction compensation
Measuring accuracy
Resolution
Isolation DC/DC
Input current (internal)
Bit width per channel
Configuration
Operating temperature
Connection technique
Dimensions (mm)WxHxL
Presetting
462, 469
2 (differential input, max. +/- 3.5V)
via system voltage
J, K, B, E, N, R, S, T, U, L, mV Messung
on each module
<25 µV, typ. 15 µV
0.1°C per Bit
500V system / power supply
65 mA max.
16 Bit: data; 8 Bit: control/status*
(detection of broken wire 750-469)
none, optional via software parameter
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
-100°C / +1370°C, Typ K
The function module 750-462 permits the direct connection of thermocouple sensors.
The module is suitable for 2 or 3-wire thermocouples. For the 2-wire connection
technique, connect the thermocouple wires between TC- and TC+ . For the 3-conductor
technique the shield is also connected. The operation of grounded sensors is provided by
means of internal electrical isolation.
The function module 750-469 alos detects a broken wire. You can find the PNs for the
different sensor types for 750-462 in the following table.
Warning: Both inputs are referenced to a common potential (not isolated)!
The linearization is provided over the complete range by a microprocessor. The
temperature ranges of the sensors are represented with a resolution of 1 bit per 0.1°C in
one word (16 Bit). Thus, 0°C corresponds to the value 0000, and 25.5°C correspond to
the value 0 x 00FF. Temperatures below 0°C are represented in two’s complement with
a leading ‘1’.
Within the whole range of all thermocouples, the function module works like a ‘µV
meter’. The voltage resolution is represented with 16 bits. A processor converts the
voltage value into a numerical value proportional to the measured temperature of the
selected type of thermocouple.
In order to compensate the offset voltage at the clamping point, a cold junction
thermocouple compensation calculation is carried out. The circuit contains a
temperature measuring sensor at the ‘CAGE CLAMP’ connection and considers the
temperature offset voltage when calculating the measured value.
Input for thermocouple modules 750-462,469
2
:$*2Ç,2Ç6<67(0
Temperature Ranges of the connectable sensors:
L
-25°C....+900°C
K
-100°C...1370°C (Default)
J
-100°C...+1200°C
750-462/000-006
E
-100°C...1000°C
750-462/000-008
T
-100°C...+400°C
750-462/000-002
N
-100°C...+1300°C
750-462/000-009
U
-25°C...+600°C
750-462/000-011
B
600°C...+1800°C
750-462/000-007
R
0°C...+1700°C
750-462/000-010
S
0°C...+1700°C
750-462/000-001
mV-Meter
-120 mV...+120 mV
750-462/000-003
Table 1: Temperature ranges of the connectable sensors
Attention: The range of the mV Meter is 0 to 120mV at the moment!
750-469/000-006
750-469/000-008
750-469/000-002
750-469/000-009
750-469/000-011
750-469/000-007
750-469/000-010
750-469/000-001
750-469/000-003
LED functions:
green LED: Function
ON: Normal
OFF: Watchdog-Timer Overflow
If the PLC does not transmit processing data for 100 ms the green LED
stops lightning.
red LED: Error
ON: Over- or underrange or broken wire (bei 750-469)
OFF: voltage is in the measuring range
Input for thermocouple modules 750-462,469
3
:$*2Ç,2Ç6<67(0
The numerical formats
All temperature values are represented in a uniform numerical format. In the default
setting (type K) one Bit corresponds to 0.1°C. The output value corresponds to the
temperature range of each sensor as defined according to standards. By using a
configuration tool, the output formats can be chosen. The linearization can be switched
off and the building of the reference temperature can be switched off also. The
following table identifies the numerical format on the default range (type K).
Temp.
°C
850
Voltage
(uV)
35314
100
Binary Value
0010 0001 0011 0100
Hex.
2134
Dec.
8500
4095
0000 0011 1110 1000
03E8
1000
25,5
1021
0000 0000 1111 1111
00FF
255
0,1
4
0000 0000 0000 0001
0001
1
0
0
0000 0000 0000 0000
0000
0
-0,1
-4
1111 1111 1111 1111
FFFF
-1
-25,5
-986
1111 1111 0000 0001
FF01
-255
-100
-3553
1111 1100 0001 1000
FC18
-1000
Table 2: Numerical formats
Input for thermocouple modules 750-462,469
4
:$*2Ç,2Ç6<67(0
2 Channel Analog Input 0-20 mA / 4- 20 mA
single ended
PN 750-465, 750-466, 750-486, 750-465/000-001
Technical Description
This description is only intended for hardware version X X X X 2 A 0 1 - - - -. The
serial number can be found on the right side of the module.
The input channels are single ended and they have a common ground potential.
The inputs are connected to +I. Via 24 V / 0 V a sensor can be provided directly from
the module. Power connections are made automatically from module to module when
snapped onto the DIN rail.
The shield is connected to „S“. The connection is made automatically when snapped
onto the DIN rail.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The input module can be connected to all buscouplers of the :$*2Ç,2Ç6<67(0
(except for the economy type)
Analog Inputs 750-465,466,486
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of channels
Nominal voltage
Current consumption
(internal)
Overvoltage protection
Signal current
Resistance
Resolution
Isolation
Conversion time
Bit width per channel
Operating temperature
Configuration
Wire connection
Dimensions
(mm)WxHxL
Analog Inputs 750-465,466,486
465
465/000-001
466
486
2
24 V DC (-15% / +20%) via power jumper contacts
75 mA typ.
0-20mA
35 V max.
4-20mA
50 Ω typ.
12 Bit
500 V system/power supply
2 ms typ.
16 Bit Data, 8 Bit Control/Status
0°C....+55°C
none, optional via software parameter
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
2
:$*2Ç,2Ç6<67(0
The numerical format
All analog values will be shown in a unit numerical format. The resolution is 12 Bits.
The following table will explain the numerical format. (750-465, 466). The 3 LSBs are
not taken into account.
Input current Input current
0-20mA
4-20mA
>20,5
>20,5
0111 1111 1111 1111
Hex.
7F FF
Dec. Status LED
32767
42
on
20
20
0111 1111 1111 1111
7F FF
32767
0
off
10
12
0100 0000 0000 0XXX
40 00
16384
0
off
5
8
0010 0000 0000 0XXX
20 00
8192
0
off
2,5
6
0001 0000 0000 0XXX
10 00
4096
0
off
0,156
4,125
0000 0001 0000 0XXX
01 00
256
0
off
0,01
4,0078
0000 0000 0001 0XXX
00 10
16
0
off
0,005
4,0039
0000 0000 0000 1XXX
00 08
8
0
off
0
4
0000 0000 0000 0XXX
00 00
7
0
off
0
3,5 - 4
0000 0000 0000 0000
0
0
0
off
0
0 - 3,5
0000 0000 0000 0000
0
0
41
Analog Inputs 750-465,466,486
Binary value
3
on
(4 -20
A)
:$*2Ç,2Ç6<67(0
The numerical format for Siemens
In addition to the full 16 bit indication of the measured value it is possible to use the
‘Siemens format’. The measured value is represented by the most significant 12 Bits.
The 3 least significant Bits are reserved for diagnostic and status purposes. (750465/000-001).
Input Binary value
current
0-20mA
X : without meaning
Hex.
F : short circuit or
F : open circuit
Ü : overflow
XFÜ
0100 0000 0000 0
001
4001
Dec.
Status
LED
16385
42
on
20
0100 0000 0000 0
000
4000
16384
0
off
10
0010 0000 0000 0
000
2000
8192
0
off
5
0001 0000 0000 0
000
1000
4096
0
off
2,5
0000 1000 0000 0
000
0800
2048
0
off
1,25
0000 0100 0000 0
000
0400
1024
0
off
0,625
0000 0010 0000 0
000
0200
512
0
off
0,0976
0000 0000 0000 1
000
0008
8
0
off
0
0000 0000 0000 0
000
0000
0
0
off
>20,5
Analog Inputs 750-465,466,486
4
:$*2Ç,2Ç6<67(0
750-466/000-200 or 750-486:
Input Binary value
current
4-20mA
>20,5
X : without meaning
F : short circuit or
Hex. Dec.
F : open circuit
Ü : overflow
XFÜ
0101 0000 0000 0
001
40 01 16385
Status
LED
42
on
20
0101 0000 0000 0
000
50 00 20480
0
off
16
0100 0000 0000 0
000
40 00 16384
0
off
12
0011 0000 0000 0
000
30 00 12288
0
off
8
0010 0000 0000 0
000
20 00
8192
0
off
4,0078
0001 0000 0000 1
000
1008
4104
0
off
4
0001 0000 0000 0
000
1000
4096
0
off
<3,5
0001 0000 0000 0
011
1003
4099
0
on
If you have questions about the formatting of this data, please contact WAGO for
I/O System technical support.
Analog Inputs 750-465,466,486
5
:$*2Ç,2Ç6<67(0
2 / 4 Channel Analog Inputs 0-10 V
single ended
PN 750-467, 468, 487, 488
Technical Description
This description is only intended for hardware version X X X X 2 A 0 0 - - - -. The
serial number can be found on the right side of the module.
The input channels are single ended and they have a common ground potential.
The inputs are connected to +I and M. The shield is connected to „S“. The connection is
made automatically when snapped onto the DIN rail.
These I/O modules are not provided with integrated power jumper contacts. The power
supply is made by the data contacts with a DC-DC converter. The modules can work
self-supporting.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The input module can be connected to all buscouplers of the :$*2Ç,2Ç6<67(0
(except for the economy type)
Analog Inputs 750-467,468,487,488
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of channels
Nominal voltage
Current consumption
(internal)
Overvoltage protection
Signal voltage
Resistance
Resolution
Isolation
Conversion time
Bit width per channel
Operating temperature
Configuration
Wire connection
Dimensions
(mm)WxHxL
Analog Inputs 750-467,468,487,488
467
2
468
487
488
4
2
4
via system voltage (DC DC converter)
60 mA
60 mA
60 mA
60 mA
35 V max.
0-10 V
133 kΩ typ.
12 Bit
500 V system/power supply
2 ms typ.
16 Bit Data, 8 Bit Control/Status
0°C....+55°C
none, optional via software parameter
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
2
:$*2Ç,2Ç6<67(0
The numerical format
All analog values will be shown in a unit numerical format. The resolution is 12 Bits.
The following table will explain the numerical format. (750-467, 468). The 3 LSBs are
not taken into account.
Input voltage
0-10V
> 10
0111 1111 1111 1111
Hex.
7F FF
Dec.
32767
Status
42
10
0111 1111 1111 1XXX
7F F8
32760
0
5
0100 0000 0000 0XXX
40 00
16384
0
2,5
0010 0000 0000 0XXX
20 00
8192
0
1,25
0001 0000 0000 0XXX
10 00
4096
0
0,0781
0000 0001 0000 0XXX
01 00
256
0
0,0049
0000 0000 0001 0XXX
00 10
16
0
0,0024
0000 0000 0000 1XXX
00 08
8
0
0
0000 0000 0000 0XXX
00 07
7
0
0
0000 0000 0000 0XXX
0
0
0
Analog Inputs 750-467,468,487,488
Binary value
3
:$*2Ç,2Ç6<67(0
The numerical format for Siemens
In addition to the full 16 bit indication of the measured value it is possible to use the
‘Siemens format’. The measured value is represented by the most significant 12 Bits.
The 3 least significant Bits are reserved for diagnostic and status purposes. (750-487,
488)
Input
voltage
0-10V
Binary value
>10
0101 0000 0000 0
10
0101 0000 0000 0
5
X : without
meaning
F : short circuit or
F : open circuit
Ü : overflow
XFÜ
001
Hex.
Dec.
Status
50 01
20481
42
000
50 00
20480
0
0011 0000 0000 0
000
30 00
12288
0
2,5
0010 0000 0000 0
000
20 00
8192
0
1,25
0001 1000 0000 0
000
18 00
6144
0
0,0049
0001 0000 0000 1
000
10 08
4104
0
0
0001 0000 0000 0
000
10 00
4096
0
If you have questions about the formatting of this data, please contact WAGO for
I/O System technical support.
Analog Inputs 750-467,468,487,488
4
:$*2Ç,2Ç6<67(0
2 Channel Analog Input 0-20mA / 4-20mA
single ended
PN 750-472, 750-472/000-200, 750-474, 750-474/000-200
Technical description:
This description is only intended for hardware and software version X X X X 0 2 0 2- - -. The serial number can be found on the right side of the module.
The input channels are single ended and they have a common ground potential.
The inputs are connected to +I. Via 24 V / 0 V a sensor can be provided directly from
the module. Power connections are made automatically from module to module when
snapped onto the DIN rail.
The shield is connected to „S“. The connection is made automatically when snapped
onto the DIN rail.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2-channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4-channel
modules).
The input module can be connected to all buscouplers of the :$*2Ç,2Ç6<67(0
(except for the economy type).
Analog Inputs 750-472, 474
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750-
474
474/000-0200
Number of channels
Nominal voltage
Overvoltage protection
Internal current
Input signal
Input current
Resistance
Input voltage
Resolution
Input filter
Noise rejection at sampling
frequency
2
24 V DC (-15% / +20%) via power jumper contacts
24 V max.
75 mA typ.
0-20mA
4-20mA
< 38 mA at 24 V
50 Ω
non-linear/overload protection: U=1,2 V DC+160Ω*Imess
internal 16 Bit, 15 Bit via fieldbus
50 Hz
< -100 dB
Transition frequency
Isolation
Conversion time
Bit width per channel
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
13 Hz
500 V system/power supply
80 ms typ.
16Bit: Data; optional 8Bit: Control/Status
none, optional via software parameter
0°C....+55°C
CAGE CLAMP; 0,08 to 2,5mm2
12 x 64* x 100
*from upper edge of the carrier rail
Noise rejection below
sampling frequency
Analog Inputs 750-472, 474
472
472/000-200
< -40 dB
2
:$*2Ç,2Ç6<67(0
The numerical format
The resolution of 750-472 and 750-474 are 15 Bit.
Input current Input current
Binary value
0-20mA
4-20mA
>20,5
>20,5
0111 1111 1111 1111
Dec.
32767
Status
42
LED
on
20
20
0111 1111 1111 1111
7F FF
32767
0
off
10
12
0100 0000 0000 0000
40 00
16384
0
off
5
8
0010 0000 0000 0000
20 00
8192
0
off
2,5
6
0001 0000 0000 0000
10 00
4096
0
off
0,156
4,125
0000 0001 0000 0000
01 00
256
0
off
0,01
4,0078
0000 0000 0001 0000
00 10
16
0
off
0,005
4,0039
0000 0000 0000 1000
00 08
8
0
off
0
4
0000 0000 0000 0000
00 00
7
0
off
0
3,5 - 4
0000 0000 0000 0000
0
0
0
off
0
0 - 3,5
0000 0000 0000 0000
0
0
41
Analog Inputs 750-472, 474
Hex.
7F FF
3
on
(4-20
A)
:$*2Ç,2Ç6<67(0
The numerical format for Siemens
In addition to the full 16 Bit indication of the measured value it is possible to use the
„Siemens format“. The measured value is represented by the most significant 12 Bits.
The 3 least significant Bits are reserved for diagnostic and status purpose (750-472/000200, 750-474/000-200). The numerical format for 750-472/000-200 is equivalent to S5
463, 750-474/000-200 equivalent to S5 460/465.
Input Binary value
current
4-20mA
X : without meaning
F : short circuit or
Hex.
F: open circuit
Ü : overflow
XFÜ
0111 1111 1111 1
001
7F F9
Dec.
Status
LED
32761
42
on
31,99
0111 1111 1111 0
000
7F F0
32752
0
off
20,5
0101 0010 0000 0
001
52 00
20992
0
off
20
0101 0000 0000 0
000
50 00
20480
0
off
16
0100 0000 0000 0
000
40 00
16384
0
off
12
0011 0000 0000 0
000
30 00
12288
0
off
8
0010 0000 0000 0
000
20 00
8192
0
off
4,0078
0001 0000 0000 1
000
10 08
4104
0
off
4
0001 0000 0000 0
000
10 00
4096
0
off
3,5
0000 1110 0000 0
011
0E 00
3584
0
on
0
0000 0000 0000 0
000
00 00
0
0
on
32
Analog Inputs 750-472, 474
4
:$*2Ç,2Ç6<67(0
Input Binary value
current
0-20mA
X : without meaning
F : short circuit or
F: open circuit
Ü : overflow
XFÜ
0110 0000 0000 0
001
Hex.
Dec.
Status
LED
6001
24577
42
on
29,98
0101 1111 1111 1
000
5F F8
24568
0
on
20,5
0100 0001 1001 1
000
41 98
16762
0
on
20
0100 0000 0000 0
000
4000
16384
0
off
10
0010 0000 0000 0
000
2000
8192
0
off
5
0001 0000 0000 0
000
1000
4096
0
off
2,5
0000 1000 0000 0
000
0800
2048
0
off
1,25
0000 0100 0000 0
000
0400
1024
0
off
0,625
0000 0010 0000 0
000
0200
512
0
off
0,00976 0000 0000 0000 1
000
0008
8
0
off
000
0000
0
0
off
30
0
0000 0000 0000 0
If you have questions about the formatting of this data, please contact WAGO for
I/O System technical support.
Analog Inputs 750-472, 474
5
:$*2Ç,2Ç6<67(0
2-Channel Analog Input
± 10 V, 16 Bit, single ended
0 -10 V, 16 Bit, single ended
750-476
750-478
Function clamp and variants
Item-No.
750-476
750-476/000-200
750-478
750-478/000-200
Analog Inputs 750-476, 478
4;13614<<<
Description
2-Channel Analog Input
± 10 V, single ended
2-Channel Analog Input
± 10 V, single ended
with status infomation within the data word
Identification
2 AI ± 10 V DC
16 Bit s.e.
2 AI ± 10 V DC
16 Bit s.e.
S5-466
2-Channel Analog Input
0-10 V, single ended
2-Channel Analog Input
0-10 V, single ended
with status infomation within the data word
2 AI 0-10 V DC
16 Bit s.e.
2 AI 0-10 V DC
16 Bit s.e.
S5-466
1
:$*2®,22®6<67(0
Technical description
This description is only intended for hardware and software version
X X X X 0 4 0 1 - - - - .The serial number can be found on the right side of the module.
The input channels are single ended and they have a common ground potential.
The inputs are connected to I and 0V.
The shield is connected to „S“. The connection is made automatically when snapped
onto the DIN rail.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2-channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4-channel
modules).
The input module can be connected to all buscouplers of the :$*2®,22®6<67(0
(except for the economy type).
Analog Inputs 750-476, 478
4;13614<<<
2
:$*2®,22®6<67(0
Technical Data
Item Number
Number of channels
Nominal voltage
Overvoltage resistance
Internal current
consumption
Input signal
Input impedance
Overvoltage protection
Resolution
Input filter
Noise rejection at sampling
frequency
Noise rejection below
sampling frequency
Transition frequency
Isolation
Wandlungszeit
Bitwidth per channel
Configuration
Operating temperature
Wire connection
Dimensions (mm)WxHxL
Analog Inputs 750-476, 478
4;13614<<<
750-476
750-476/000-200
750-478
750-478/000-200
+/- 10 V
0 - 10 V
2
via system voltage (DC/DC)
24 V max.
75 mA typ.
130 kΩ typ.
24 V protected against polarity reversal
15 Bit + sign
50 Hz
< -100 dB
< -40 dB
13 Hz
500 V system/power supply
80 ms typ.
16Bit: Data;
optional 8Bit: control/status
none, optional via software parameter
0°C....+55°C
CAGE CLAMP; 0,08 bis 2,5mm2
12 x 64* x 100
* from upper edge of the carrier rail
3
:$*2®,22®6<67(0
The numerical format
All analog values will be shown in a unit numerical format. The resolution for 750-476
and 750-478 is 15 Bit plus sign.
750-476, -478
Input voltage
0-10V
±10V
Hex.
Dec.
Status
(hex)
LED
error
I (1,2)
>11
>11
0111 1111 1111 1111
0x7FFF
32767 0x42
>10,5
>10,5
0111 1111 1111 1111
0x7FFF
32767 0x42
off
10
10
0111 1111 1111 1111
0x7FFF
32767 0x00
off
5
5
0100 0000 0000 0000
0x4000
16384 0x00
off
2,5
2,5
0010 0000 0000 0000
0x2000
8192 0x00
off
1,25
1,25
0001 0000 0000 0000
0x1000
4096 0x00
off
0,0781
0,0781
0000 0001 0000 0000
0x0100
256 0x00
off
0,049
0,049
0000 0000 0001 0000
0x0010
16 0x00
off
0,0003
0,0003
0000 0000 0000 0001
0x0001
1 0x00
off
0
0
0000 0000 0000 0000
0x0000
0 0x00
off
<-0,5
0000 0000 0000 0000
0x0000
0 0x41
off
<-1
0000 0000 0000 0000
0x0000
0 0x41
on
-5
1100 0000 0000 0000
0xC000
49152 0x00
off
-10
1000 0000 0000 0000
0x8000
32768 0x00
off
<-10,5
1000 0000 0000 0000
0x8000
32768 0x41
off
<-11
1000 0000 0000 0000
0x8000
32768 0x41
on
Analog Inputs 750-476, 478
4;13614<<<
Binary
Value
4
on
:$*2®,22®6<67(0
Numerical format with status information
For fieldbus master, which evaluates status information in the data word, e.g. from
Siemens, a variant of the function clamp is available.
The format containes the status in Bit B0 .. B2.
The digitalized measuring value is placed at the position Bit B3 .. B15. The numerical
format is equivalent to S5 466.
750-476/000-200
Input
Value
Status LED
error
voltage
Binary
Hex.
Dec.
I (1,2)
*)
±10 V
XEO
> 11
0011 1111 1111 1 0 0 1
0x3FF9 16377 0x42
on
> 10,5
0011 1111 1111 1 0 0 1
0x3FF9 16377 0x42
off
10
0011 1111 1111 1 0 0 0
0x3FF8 16376 0x00
off
5
0010 0000 0000 0 0 0 0
0x2000 8192 0x00
off
2,5
0001 0000 0000 0 0 0 0
0x1000 4096 0x00
off
1,25
0000 1000 0000 0 0 0 0
0x0800 2048 0x00
off
0,0781
0000 0000 1000 0 0 0 0
0x0080
128 0x00
off
0,0049
0000 0000 0000 1 0 0 0
0x0008
8 0x00
off
0
0000 0000 0000 0 0 0 0
0x0000
0 0x00
off
-5
1110 0000 0000 0 0 0 0
0xE000 57344 0x00
off
-10
1100 0000 0000 0 0 0 0
0xC000 49152 0x00
off
< -10,5
1100 0000 0000 0 0 0 1
0xC001 49153 0x41
off
< -11
1100 0000 0000 0 0 0 1
0xC001 49153 0x41
on
*)
X : without meaning, E : short circuit or open circuit, O : overflow
750-478/000-200
Input
Value
Status LED
error
voltage
Binary
Hex.
Dec.
I (1,2)
*)
0-10 V
XEO
> 11
0111 1111 1111 1 0 0 1
0x7FF9 32761 0x42
on
> 10,5
0111 1111 1111 1 0 0 1
0x7FF9 32761 0x42
off
10
0111 1111 1111 1 0 0 0
0x7FF8 32760 0x00
off
5
0100 0000 0000 0 0 0 0
0x4000 16384 0x00
off
2,5
0010 0000 0000 0 0 0 0
0x2000 8192 0x00
off
1,25
0001 0000 0000 0 0 0 0
0x1000 4096 0x00
off
0,0781 0000 0001 0000 0 0 0 0
0x0100
256 0x00
off
0,049
0000 0000 0001 0 0 0 0
0x0010
16 0x00
off
0,024
0000 0000 0000 1 0 0 0
0x0008
8 0x00
off
0
0000 0000 0000 0 0 0 0
0x0000
0 0x00
off
< -0,5
0000 0000 0000 0 0 0 1
0x0001
1 0x41
off
< -1
0000 0000 0000 0 0 0 1
0x0001
1 0x41
on
*)
X : without meaning, E : short circuit or open circuit, O : overflow
Analog Inputs 750-476, 478
4;13614<<<
5
:$*2®,22®6<67(0
Status byte
Structure of the status byte:
bit
meaning
• ERROR
• Overrange
• Underrange
Analog Inputs 750-476, 478
4;13614<<<
7
0
6
ERROR
5
4
3
2
res. res. res. res.
1
Overrange
0
Underrange
error at the input channel.
exceed the allowable measuring range.
fall below the allowable measuring range.
6
:$*2®,22®6<67(0
2 Channel Analog Outputs 0-10 V
PN 750-550, 750-580
Technical Description
This description is only intended for hardware version X X X X 2 A 0 1 - - - -. The
serial number can be found on the right side of the module.
The output signal of 750-550/551 is a 0-10 V signal. Sensors may be connected to „O“
and to the common ground.
The shield is connected to „S“. The connection is made automatically when snapped
onto the DIN rail.
These I/O modules are not provided with integrated power jumper contacts. The power
supply is made by the data contacts with a DC-DC converter. The modules can work
self-supporting.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The output module can be connected to all buscouplers of the
:$*2Ç,2Ç6<67(0 (except for the economy type)
Analog Outputs 750-550,580
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of channels
Nominal voltage
Current consumption
(internal)
Voltage supply
Signal voltage
Resistance
Resolution
Isolation
Bit width per channel
Operating temperature
Configuration
Wire connection
Dimensions
(mm)WxHxL
550, 580
2
via system voltage (DC DC converter)
65 mA
via system voltage (DC-DC)
0-10 V
> 5 kΩ
12 Bit
500 V system/power supply
16 Bit Data, 8 Bit Control/Status
0°C....+55°C
none, optional via software parameter
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
The numerical format
All analog values will be shown in a unit numerical format. The resolution is 12 Bits.
The 3 LSBs are not taken into account. The following table will explain the numerical
format. (750-550).
Output voltage 0-10 V
Binary Value
Hex.
Dec.
10
0111 1111 1111 1111
7F F8
32767
5
0100 0000 0000 0000
40 00
16384
2.5
0010 0000 0000 0000
20 00
8192
1.25
0001 0000 0000 0000
10 00
4096
0.0781
0000 0001 0000 0000
01 00
256
0.0049
0000 0000 0001 0000
00 10
16
0.0024
0000 0000 0000 1000
00 08
8
0
0000 0000 0000 0111
00 07
7
0
0000 0000 0000 0000
0
0
Analog Outputs 750-550,580
2
:$*2Ç,2Ç6<67(0
The numerical format for Siemens
In addition to the full 16 bit indication of the measured value it is possible to use the
‘Siemens format’. The measured value is represented by the most significant 12 Bits.
The 3 least significant Bits are reserved for diagnostic and status purposes. (750-580)
Output
voltage
0-10 V
> 10
Binary value
Hex.
Dec.
0101 0000 0000 XXXX
50 01
20481
10
0100 0000 0000 XXXX
40 00
16384
7.5
0011 0000 0000 XXXX
30 00
12288
5
0010 0000 0000 XXXX
20 00
8192
2.5
0001 0000 0001 XXXX
10 08
4104
1.25
0000 1000 0000 XXXX
800
2048
0
0000 0000 0000 XXXX
0
0
If you have questions about the formatting of this data, please contact WAGO for
I/O System technical support.
Analog Outputs 750-550,580
3
:$*2Ç,2Ç6<67(0
2 -Channel Analog Outputs 0-20 mA / 4-20 mA
PN 750-552, 554, 584
Technical Description
This description is only intended for hardware version X X X X 2 A 0 1 - - - -. The
serial number can be found on the right side of the module.
The output signal of 750-552...555, 584 is a 0-10 mA or 4-20 mA signal. Sensors may
be connected to „O“ and to the common ground (0V).
The shield is connected to „S“. The connection is made automatically when snapped
onto the DIN rail.
Power connections are made automatically from module to module when snapped onto
the DIN rail. For a self-supporting function, the power supply has to be connected by an
input module (e.g. 750-602).
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The output module can be connected to all buscouplers of the
:$*2Ç,2Ç6<67(0 (except for the economy type)
Analog Outputs 750-552, 554, 584
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of channels
Current consumption
(internal)
Nominal voltage
Signal current
Resistance
Resolution
Isolation
Bit width per channel
Operating temperature
Configuration
Wire connection
Dimensions
(mm)WxHxL
552
554
2
60 mA max.
584
24 V DC (-15% /+20%) via power jumper contacts
0-20mA
4-20mA
4-20mA
<500 Ω
12 Bit
500 V system/power supply
16 Bit Data, 8 Bit Control/Status
0°C....+55°C
none, optional via software parameter
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of carrier rail)
The numerical format
All analog values will be shown in a unit numerical format. The following table will
explain the numerical format. (750-552/554). The 3 LSBs are not taken into account.
Output
Output
Binary Value
current 0-20 current 4-20
Hex.
Dec.
20
20
0111 1111 1111 1111
7F FF
32767
10
12
0100 0000 0000 0000
40 00
16384
5
8
0010 0000 0000 0000
20 00
8192
2.5
6
0001 0000 0000 0000
10 00
4096
0.156
4.125
0000 0001 0000 0000
01 00
256
0.01
4.0078
0000 0000 0001 0000
00 10
16
0.005
4.0039
0000 0000 0000 1000
00 08
8
0
4
0000 0000 0000 0111
00 07
7
0
4
0000 0000 0000 0000
0
0
Analog Outputs 750-552, 554, 584
2
:$*2Ç,2Ç6<67(0
The numerical format for Siemens
In addition to the full 16 bit indication of the measured value it is possible to use the
‘Siemens format’. The measured value is represented by the most significant 12 Bits.
The 4 least significant Bits have no function. (750-584)
Output
current 4-20
mA
20
Binary value
Hex.
Dec.
0100 0000 0000 XXXX
40 00
16384
16
0011 0000 0000 XXXX
30 00
12288
12
0010 0000 0000 XXXX
20 00
8192
8
0001 0000 0000 XXXX
10 00
4096
4.015
0000 0000 0001 XXXX
00 10
16
4
0000 0000 0000 XXXX
00 00
0
If you have questions about the formatting of this data, please contact WAGO for
I/O System technical support.
Analog Outputs 750-552, 554, 584
3
:$*2Ç,2Ç6<67(0
2 Channel Analog Outputs +/- 10 V
PN 750-556
Technical Description
This description is only intended for hardware version X X X X 2 A 0 1 - - - -. The
serial number can be found on the right side of the module.
The output signal of 750-556 is a +/- 10 V signal. Sensors may be connected to „O“ and
to the common ground (0V).
The shield is connected to „S“. The connection is made automatically when snapped
onto the DIN rail.
These I/O modules are not provided with integrated power jumper contacts. The power
supply is made by the data contacts with a DC-DC converter. The modules can work
self-supporting.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The input module can be connected to all buscouplers of the :$*2Ç,2Ç6<67(0
(except for the economy type)
Analog Outputs 750-556
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Number of channels
Nominal voltage
Current consumption
(internal)
Signal voltage
Resistance
Resolution
Isolation
Bit width per channel
Operating temperature
Configuration
Wire connection
Dimensions
(mm)WxHxL
Analog Outputs 750-556
556
2
via system voltage (DC DC converter)
65 mA
+/- 10 V
> 5 kΩ
12 Bit
500 V System/Power supply
16 Bit Data, 8 Bit Control/Status
0°C....+55°C
none, optional via software parameter
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
2
:$*2Ç,2Ç6<67(0
The numerical format
All analog values will be shown in a unit numerical format. The resolution is 12 Bits
and the 3 LSBs are ignored. The following table will explain the numerical format.
Input voltage +/- 10 V
Binary Value
10
Analog Outputs 750-556
0111 1111 1111 1111
Hex.
7F FF
Dec.
32767
5
0100 0000 0000 0000
40 00
16384
2.5
0010 0000 0000 0000
20 00
8192
1.25
0001 0000 0000 0000
10 00
4096
0.0781
0000 0001 0000 0000
01 00
256
0.0049
0000 0000 0001 0000
00 10
16
0.0024
0000 0000 0000 1111
00 0F
15
0
0000 0000 0000 0000
0
00
-2.5
1110 0000 0000 0000
E0 00
57344
-5
1100 0000 0000 0000
C0 00
49152
-7.5
1010 0000 0000 0000
A0 00
40960
-10
1000 0000 0000 0000
80 00
32768
3
:$*2Ç,2Ç6<67(0
End module, Potential multiplication module,
Separation module
PN750-600, 750-614, 750-616, 750-616/030-000
Technical Description
After the fieldbus node is assembled with the correct buscoupler and selected I/O
modules, the end module is snapped onto the assembly. It completes the internal data
circuit and ensures correct data flow.
The potential multiplication module allows additional + and - voltage connection points
(up to 4 additional). This eliminates external terminal blocks.
Technical Data:
Item Number 750Voltage
Current on contacts
Operating temperature
Wire connection
Dimensions (mm) WxHxL
600
-
max. 10 mA
0 °C ... + 55 °C
CAGE CLAMP; 0,08 to 2,5 mm²
12 x 64 x 100, (from the upper edge of the carrier rail)
End module, Potential multiplication 750-600,614,616
614
24 V - 230 V AC/DC
1
:$*2Ç,2Ç6<67(0
Separation module
Technical description:
Use of this module allows increased air- and creepage distances between different field
voltages within a node.
There are two different types of the separation module. With PN 750-616 you get a
module without printing. PN 750-616/030-000 looks like the right one in the above
picture.
Technical Data:
Item No.
Dimensions (mm) W x H x L
750-616, 750-616/030-000
12 x 64* x 100, (*from the upper edge of the carrier rail)
End module, Potential multiplication 750-600,614,616
2
:$*2Ç,2Ç6<67(0
Supply modules
PN750-601, 602, 609, 610, 611, 612, 613, 615
Technical Description
The supply module provides I/O module power through the power jumper contacts.
Maximum current supply to all connected modules is 10 A. Maximum current supply to
the modules with fuse holder is 6.3 A. Should higher currents be necessary, intermediate
supply modules may be added in the assembly.
The modules 750-601, 609, 615, 610 and 611 are additionally equipped with a fuse
holder. The change of the fuse is very easy by drawing out the fuse holder and changing
the fuse. A blown fuse is indicated by a LED.
The modules 750-610 and 611 send information about the status of the supply module
to the fieldbus coupler through two input bits.
Bit1
Bit2
Description
0
0
voltage < 15 V DC
1
0
fuse blown
0
1
fuse o.k., voltage o.k.
Using the supply modules you have to look for the allowed voltage. The following table
shows the voltage for the supply modules.
The supply module 750-613 supplies the field side and te internal databus system
voltage. The internal system voltage can supply 2 A max. If the sum of the internal
current consumption exceeds 2 A, an additional supply module must be added.
Supply modules 750-601,602, 609,615,610,611,613
1
:$*2Ç,2Ç6<67(0
Technical Data:
Item Number 750Voltage
602
24 V DC
Current via contacts
Operating temperature
Wire connection
Dimensions (mm) W x H x L
internal current 750-613: max. 2 A
601
24 V DC
Item Number 750Number of inputs
Current consumption
Internal bitwidth
610
Voltage
Current via contacts
Fuse
Operating temperature
Wire connection
Dimensions (mm) W x H x L
Supply modules 750-601,602, 609,615,610,611,613
max. 10 A
0 °C ... + 55 °C
CAGE CLAMP; 0,08 to 2,5 mm²
12 x 64 x 100, (from the upper edge of the carrier rail)
Item Number 750Voltage
Current via contacts
Fuse
Operating temperature
Wire connection
Dimensions (mm) W x H x L
612
613
0 - 230 V AC/DC 24 V DC
(-15%/+20%)
609
230 V AC
615
120 V AC
max. 6.3 A
5 x 20, 6.3 A
0 °C ... + 55 °C
CAGE CLAMP; 0,08 to 2,5 mm²
12 x 64 x 100, (from the upper edge of the carrier rail)
611
24 V DC
2
5 mA
2
230 V AC
max. 6.3 A
5 x 20, 6.3 A
0 °C ... + 55 °C
CAGE CLAMP; 0,08 to 2,5 mm²
12 x 64 x 100, (from the upper edge of the carrier rail)
2
:$*2Ç,2Ç6<67(0
Binary spacer module
PN 750-622
1XPEHURILQSXWVRURXWSXWV
,QSXWVRU2XWSXWV
:$*2
9
ON
1 23 45
9
Technical description
The binary spacer module reserves bit-addresses in the WAGO buscoupler.
The number of in or outputs can be chosen by two DIP switches. 2, 4, 6 or 8 bits are
possible (1, 2, 3 or 4-channel modules). A third DIP Switch chooses inputs or outputs.
The kind of configuration is indicated by means of 3 LEDs even if there is no voltage
applied.
The binary spacer module works like a supply module. The power supply must be made
for the following modules.
Binary spacer module 750-622
1
:$*2⇓,2⇓6<67(0
Technical Data
Item number 750Number of in- or outputs
Nominal voltage
Internal current consumption
Voltage (field side)
Current via power jumper
contacts
Input current (field side)
Isolation
Internal bit width
Configuration
Operating temperature
Wire connection
Dimensions (mm) WxHxL
622
2, 4, 6 or 8
5 V DC internal
10 mA max.
24 V DC (-15%/+20%)
10 A max.
500 V system/power supply
2, 4, 6 oder 8
none, optional via software parameter
0°C....+55°C
CAGE CLAMP; 0.08 to 2.5mm2
12 x 64* x 100 (*from upper edge of the carrier rail)
The DIP switches and LEDs are used as fol lows. When the switch is OFF the LED is
also OFF (dark g reen symbol). When the switch is ON the LED lightens (yellow
symbol).
ON
12345
;
;
'RQ·WFDUH
2))
,QSXWV
21
2XWSXWV
2)) 2))
%LW[%LW
21
2))
%LW[%LW
2)) 21
%LW[%LW
21
%LW[%LW
21
Examples:
ON
12345
6 binary outputs (3x 2-channel output modules)
ON
12345
Binary spacer module 750-622
4 binary inputs (2x 2-channel input modules)
2
:$*2⇓,2⇓6<67(0
SSI Encoder Interface
PN 750-630, 750-630/000-001, 750-630/000-006
Technical Description:
This technical description is only valid for hardware and software versions
X X X X 2 B 0 2----. The product series number is printed on the right side of the
module.
The operational mode of the module is factory preset to discern a 24 bit absolute
encoder Graycode signal transmitted at 125kHz.
The following description is preliminary and is applicable to the factory configuration.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The SSI Interface is able to run with all WAGOÇI/OÇSYSTEM bus-couplers (except
for the economy type).
SSI encoder 750-630
1
:$*2Ç,2Ç6<67(0
Technical Data:
Series 750
Encoder connections
Current consumption
(internal)
Power supply
Sensor power supply
Baud rate
Data field width
Signal output (clock)
Signal input (positional)
Output data format
Bit width
Configuration
Signal isolation
Temperature range
Wire connection
Dimensions (mm) WxHxL
Default Configuration
SSI encoder 750-630
630
630/000-001
630/000-006
Data Input: D+; D-; Clock Output: CI+; CI85mA typ.
24V DC (-15%/+20%)
24V DC via power jumper contacts
max. 1 MHz
32 Bit
differential RS 422
differential RS 422
Graycode / Dualcode
32 Bit: Data; 8 Bit: Control/Status
none, optional via software parameter
500 V system/power supply
0°C....+55°C
CAGE CLAMP; 0.08 x 2.5mm2
AWG 28-14
12 x 64* x 100 (*from upper edge of carrier rail)
125 kHz
125 kHz
250 kHz
Graycode
Binary
Graycode
24 Bit Data
24 Bit Data
24 Bit Data
Resolution
Resolution
Resolution
2
:$*2Ç,2Ç6<67(0
Terminal Configuration:
Input
Signal D+ and Signal DSignal Cl+ and Signal CL+24 V DC
0 V DC
Type
Input, RS422
Output, RS422
Input
Input
Function
Positional data from encoder, Graycode.
Clock signal output for communications interface.
24 V DC supply voltage to module, field connection.
0 V DC supply voltage return to module, field
connection.
The use of this module in conjunction with a SSI encoder provides direct positional
information rather than the type of data resultant from incremental type encoders.
Absolute encoders are comprised of several data disks which generate a data
word which is unique through out the 360 degrees of rotation. The data format
is a modified binary pattern in either Graycode or Dualcode.
The resolution of the sensor depends upon the configuration of the sensor and
the physical number of revolutions in the motion profile. Since the basis of the
encoder is to provide absolute positional information based upon a mechanical
configuration limited to one revolution or less. The maximum resolution of this
module is 24 bit.
The frequency of the data signal input to the SSI module is maintained at 125 kHz.
Listed below are the recommended cable lengths for the various clock signal Baud
rates.
Baud rate
100 kHz
200 kHz
300 kHz
400 kHz
SSI encoder 750-630
Maximum
cable length
400 meters
200 meters
100 meters
50 meters
3
:$*2Ç,2Ç6<67(0
Organization of the in- and output data for Interbus
The module is seen like an analog input with 2 x 16 Bit input data.
Inputs:
Word
D0 (Bit 0-15)
D1 (Bit 16-31)
SSI encoder 750-630
Data Word Designation
Positional data,
Input byte 1
Positional data,
Input byte 3
4
Positional data,
Input byte 0
Positional data,
Input byte 2
:$*2Ç,2Ç6<67(0
Quadrature Encoder Interface
PN 750-631, 750-631/000-001
Technical Description:
This technical description is only valid for hardware and software versions X X X X 2 B
0 1----. The product series number is printed on the right side of the module.
The described operational mode is 4 times or quadrature sampling.
The following description is preliminary and is applicable to the factory configuration.
Attention:
The lowest power jumper contact is not carried out for some modules (e.g. 4-channel)!
A module which needs all contacts (e.g. 2 channel digital) may not be connected to the
right hand side of modules which do not have 3 power jumper contacts (e.g. 4 channel
modules).
The Quadrature Encoder Interface is able to run with all WAGOÇI/OÇSYSTEM buscouplers (except for the economy type).
Quadrature Encoder 750-631
1
:$*2Ç,2Ç6<67(0
Technical Data:
Series 750Encoder connections
Current consumption
(internal)
Sensor supply voltage
Data word
Maximum frequency
Counter modes
Data latch word
Commands
Supply voltage
Current consumption
Sensor
Bit width
Configuration
Operational temperature
Wire connection
Dimensions (mm) WxHxL
Default configuration
Quadrature Encoder 750-631
631
631/000-001
A, A(inv.); B, B(inv.); Index, Index(inv.)
25 mA
5 V DC
16 Bit Binary
1 MHz
1-2-4 times sampling
16 Bit
read, reset, start
24 V DC (-15%/+20%)
85mA Field (without sensor)
0.1 A (without sensor load)
1 x 32 Bit: Data; 8 Bit:Control/Status
none, optional via software parameter
0°C....+55°C
CAGE CLAMP; 0.08 x 2.5mm2
AWG 28-14
24 x 64* x 100 (*from upper edge of the carrier rail)
4 times sampling
1 time sampling
2
:$*2Ç,2Ç6<67(0
Operational Characteristics:
The quadrature encoder interface accepts up to two input signals for the counting
increment. The index pulse may also be considered should the control configuration
require. There is also a Latch and Gate input available on the module for added
functionality.
The quadrature encoder provides two signals that are shifted 90 degrees from each
other, signals A and B. In order to achieve a better common mode noise rejection ratio,
the output signals from the encoder are transmitted via a differential signal. Their
complement signals, A(inv.) and B(inv.) are also transmitted. A directional
determination may be made by which signal leads. If the A signal leads, the direction is
considered to be forward. If the B signal leads, the direction is considered to be reverse.
By exchanging the A and A(inv.) the phase relationship will be changed by 180 degrees,
thus allowing the direction to be preset via the wiring configuration.
Most quadrature encoders have an Index signal, or Z rev, as well as the incremental
signal. This signal provides one pulse per revolution with a duration equal to an
incremental pulse.
The inputs to the quadrature encoder module must be supplied from an encoder with
Line Driver Outputs for proper operation. The 5 Volt DC output may be used to power
the encoder. The 24 Volt DC input supply must be provided from an external power
supply.
The Gate and Latch inputs are 24 Volt DC.
Module Inputs and Outputs
Connection
Type
Signal A and Signal Input,
A(inv.)
TTL
Signal B and Signal Input,
B(inv.)
TTL
Signal C and Signal Input,
C(inv.)
TTL
Shield
Input
Sensor 0V DC
Output
Sensor +5V DC
Output
+24V DC
Input
0V DC
Input.
Gate
Input,
24V DC
Latch
Input,
24V DC
Function
Incremental pulse signals for channel A
Incremental pulse signals for channel B
Index pulse signals
Shield connection for encoder wiring
Supply return for encoder supply
5 Volt DC supply for encoder
24 Volt DC supply, field connection
Supply return, field connection
24 Volt DC input for gate signal
24 Volt DC input for Latch signal
The Input Gate stops the counter. Only 0 V or an open connection initialize the counter.
24 V stops the counting process.
Quadrature Encoder 750-631
3
:$*2Ç,2Ç6<67(0
The input Latch controls the overtaking of the actual counter value into the
Latchregister. This input is activated by teh control bit EN_LATEXT („1“). EN_LACT
has to be deactivated („0“). The first change from 0 V to 24 V at the Latch input takes
the actual counter value into the Latchregister.
The control byte contains the information as listed below.
Control Byte Configuration
Bit 7 Bit 6 Bit 5
0
x
CFAST_M
0
x
Operation
Mode
Bit 4
x
x
Bit 3
x
x
Bit 2
CNT_SET
Counter Set
Bit 1
EN_LATEXT
Release Latch
Bit 0
EN_LATC
Release Index
Pulse
Please note Bit 7 is a reserved bit and must always be set to 0. It is responsible for
register communication which is not decribed in this chapter.
Bit
CFAST_M
Function
Fast mode operation. Only the counter module function will be
operable. All other control bits will be ignored.
The counter module will be preset to a count value with a rising
edge.
0=The external latch input is deactivated.
1=The module will latch in the counter data on the first rising edge.
Other changes have no effect.
0=Latching data with the Index pulse is deactivated.
1=The Index pulse will latch in the counter data on the first
rising edge. Other changes have no effect.
CNT_SET
EN_LATEXT
EN_LACT
The status byte contains the information as listed below.
Status Byte Configuration
Bit 7 Bit 6 Bit 5 Bit 4
Bit 3
Bit 2
0
x
x
OVERFLOW UNDERFLOW CNTSET_ACC
0
x
x
Bit
OVERFLOW
UNDERFLOW
CNTSET_ACC
LATEXT_VAL
LACT_VAL
Quadrature Encoder 750-631
Counter
Overflow
Counter
Underflow
Counter Set
Acknowledge
Bit 1
LATEXT_
VAL
External
Latch Ack.
Bit 0
LATC_
VAL
Latched
Data Set
Function
The Overflow bit will be set if the counter value rolls over from 65535 to
0. This bit will automatically be reset if the counter passes through more
than one third of the count range, 21845 to 21846, or if an Underflow
occurs.
The Underflow bit will be set if the counter value rolls back from 65535
to 0. This bit will automatically be reset if the counter passes through
more than two thirds of the count range, 43690 to 43689, or if an
Overflow occurs.
The Counter Set Acknowledge but is set when a valid counter value is
preset to the module.
The Latch External Valid Acknowledge bit is set when a counter
value is latched into the module via the Latch input.
The Latch Index Pulse Valid Acknowledge bit is set when a counter
value is latched into the module via the Index pulse.
4
:$*2Ç,2Ç6<67(0
It is possible to process and/or check the below listed actions via the control and status
bits.
Extending the 16 bit counting range: The internal counting range is 16 bits or a
maximum value of 65535. Should the application require an extended count range the
location-difference-integration method may be employed. This method uses the control
system to store the interrogated counter value. Any new interrogated value will have the
previously stored counter value subtracted from it. This value will then be added to an
accumulated register value. It is assumed that the counter difference of the two
interrogated values is smaller than 16 bits therefore overflows need not be considered.
Another method calculates the extended counter range via the underflow and overflow
status bits. The interrogated value is either added or subtracted to the accumulation
register depending upon the status of the overflow or underflow bits.
Set Counter Position: The presetting of the counter is possible via the CNT_SET bit.
The desired preset is loaded into the data register and the CNT_SET bit is set from 0 to
1. The CNTSET_ACC bit will be set to 1 when the preset value is loaded into the count
register.
Maintaining the Present Counter Position: The counter present value may be
maintained or latched via the external Latch input. First the external latch must be
enabled via the EN_LATEXT bit. Once the input is enabled, the data will be latched
into the counter module upon a 0 to 1 transition. Upon completion of the latch process
the external latch valid bit LATEXT_VAL will be set to 1.
Maintaining a Reference Point: The storage of a present counter value may also
accomplished via the Index pulse from the encoder. First the index latch enable bit must
be set, EN_LACT, to a value 1. The counter present value will be latched upon the low
to high transition of the Index input. Upon completion of the data latch process the
Index Latch Valid bit, LACT_VAL will be set to 1.
Quadrature Encoder 750-631
5
:$*2Ç,2Ç6<67(0
Organization of the in- and output data for Interbus
The module is seen like an analog module with 3 x 16 Bit input and output data.
Outputs:
Word
D0 (Bit 0-15)
D1 (Bit 16-31)
D2 (Bit 32-47)
function
control byte
set counter-Byte0
set counter-Byte1
Inputs:
Word
D0 (Bit 0-15)
D1 (Bit 16-31)
D2 (Bit 32-47)
Quadrature Encoder 750-631
function
Statusbyte
counter byte 0
Latch value-Byte1
6
counter byte 1
Latch value-Byte0
:$*2Ç,2Ç6<67(0
RS232C Interface, TTY Interface -20 mA Current Loop
RS485C Interface
PN 750-650, 750-651, 750-653, 750-650/000-001
Technical Description:
This technical description is only valid for hardware and software versions X X X X 2 C
0 3----. The product series number is printed on the right side of the module.
The operational mode described below is the presetting.
The following description is preliminary and is applicable to the factory configuration.
Many other operational modes are possible (please contact WAGO for the
corresponding settings).
Attention:
Some modules do not provide all power jumper contacts (e.g. 4-channel)! A module
which needs all contacts (e.g. 2 channel digital) cannot be connected to the right hand
side of modules which do not have 3 power jumper contacts.
The interface module is able to run with all WAGOÇI/OÇSYSTEM buscouplers
(except for the economy type).
RS232,TTY,RS485 750-650,651,653
1
:$*2Ç,2Ç6<67(0
Technical Data:
Series 750Transmission channel
Transmission rate
Bit skew
Bit transmission
Resistance
Current consumption
(internal)
Transmission length
Input buffer
Output buffer
Voltage supply
Isolation
Bit width internal
Configuration
Operating temperature
Wire connection
Dimensions(mm) W x H x
L
Factory preset
Baud rate
Bit width internal
RS232,TTY,RS485 750-650,651,653
650,650/000-001 651
2 (1/1), T x D and R x D, full
duplex
1200 - 19200 baud
<3%
2 x 20 mA
passive
< 500 Ω
50 mA max.
653
2, autom.
Send/Receive
acc. to ISO 8482/
DIN 66259 T 4
-
max. 15 m RS
max. 1000 m
max. 500 m twisted
232 cable
twisted pair
pair
128 bytes
16 bytes
via internal system supply
500 V System/Supply
1 x 40 bit, 1 x 8 bit Control/Status
none, parameter configuration with software
0 °C ... + 55 °C
CAGE CLAMP; 0,08 bis 2,5 mm²
12 x 64* x 100 (*from upper edge of the carrier rail)
9600 baud
1 x 24 bit in/out, 1 x 8 bit Control/Status
2
:$*2Ç,2Ç6<67(0
Description of RS 232:
The interface module is designed to operate with all WAGO I/O fieldbus couplers. The
serial interface module allows the connection of RS 232-Interface devices to the WAGO
I/O SYSTEM. The RS 232 Interface module can provide gateways within the fieldbus
protocol. This allows serial equipment such as printers, barcode readers, and links to
local operator interfaces to communicate directly by the fieldbus protocol with the PLC
or PC Master.
This module supports no higher level of protocol. Communication is made completely
transparent to the fieldbus allowing flexibility in further applications of the serial
interface module. The communication protocols are configured at the Master PLC or
PC.
The 128 byte input buffer provides for high rates of data transmission. When using
lower rates of transmission speed you can collect the received data, with less priority,
without loosing data.
The 16 byte output buffer provides for faster transmission of larger data strings.
FUNCTION The data transmission takes place at 9.600 baud (default value). 1 startbit, 8 databits and 1
stopbit will be transmitted. No parity is available. The user controls data via the RTS and
CTS signals. These signals are generated in the module depending on the loading status of
the buffers. These controls can be deactivated by means of an external jumper. RTS and
CTS are to be connected.
For testing purposes the Windows 3.11 terminal emulation can be used. A cable with a 9pole sub-D socket is required. Pin 5 is connected to input M. Pin 2 is connected to TxD and
Pin 3 to RxD. RTS and CTS of the module are connected. A hardwarehandshake between
terminal emulation and SPS is not possible though.
Figure 2: Data Word Signal
RS232,TTY,RS485 750-650,651,653
3
:$*2Ç,2Ç6<67(0
Description of TTY:
The interface module is designed to operate with all WAGO I/O fieldbus couplers. The
TTY interface module allows the connection of TTY-Interface devices to the WAGO
I/O SYSTEM. The TTY Interface module can provide gateways within the fieldbus
protocol. This allows serial equipment such as printers, barcode readers, and links to
local operator interfaces to communicate directly by the fieldbus protocol with the PLC
or PC Master.
This module supports no higher level of protocol. Communication is made completely
transparent to the fieldbus allowing flexibility in further applications of the serial
interface module. The communication protocols are configured at the Master PLC or
PC.
FUNCTION
The 128 byte input buffer provides for high rates of data transmission. When using
lower rates of transmission speed you can collect the received data, with less priority,
without loosing data.
The 16 byte output buffer provides for faster transmission of larger data strings.
The data transmission takes place at 9600 baud (default value). 1 startbit, 8 databits and 1
stopbit will be transmitted. No parity is available. The drivers are high ohmic. The control
of data is made by the user software.
The TTY Interface is passive in sending and receiving , thus having no current sources.
For data conversion an active partner is needed or an additional current source has to be
connected.
FXUUHQWVRXUFH
FXUUHQWVRXUFH
UHFHLYHU
P$
P$
ZLWKFXUUHQWVRXUFH
P$
TxD TxD
+
-
TxD TxD
+
-
UHFHLYHU
TxD TxD
+
-
WUDQVPLWWHU
RxD RxD
+
-
UHFHLYHU
FXUUHQWVRXUFH
WUDQVPLWWHUZLWK
P$
FXUUHQWVRXUFH
P$
RxD RxD
+
-
:$*2
:$*2
WUDQVPLWWHU
:$*2
SRLQWWRSRLQWFRQQHFWLRQ
SRLQWWRSRLQWFRQQHFWLRQZLWKSDVVLYH
EXVFRQQHFWLRQZLWKDFXUUHQWVRXUFH
ZLWKDFWLYHSDUWQHUV
SDUWQHUVDQGDGGLWLRQDOFXUUHQWVRXUFHV
DQGDSDVVLYHPRGXOH
RS232,TTY,RS485 750-650,651,653
RxD RxD
+
-
4
:$*2Ç,2Ç6<67(0
Description of RS 485:
The interface module is designed to operate with all WAGO I/O fieldbus couplers. The
serial interface module allows the connection of RS485 or RS488-Interface devices to
the WAGO I/O SYSTEM. The RS485/RS488 Interface module can provide gateways
within the fieldbus protocol. This allows serial equipment such as printers, barcode
readers, and links to local operator interfaces to communicate directly by the fieldbus
protocol with the PLC or PC Master.
This module supports no higher level of protocol. Communication is made completely
transparent to the fieldbus allowing flexibility in further applications of the serial
interface module. The communication protocols are configured at the Master PLC or
PC.
The 128 byte input buffer provides for high rates of data transmission. When using
lower rates of transmission speed you can collect the received data, with less priority,
without loosing data.
The 16 byte output buffer provides for faster transmission of larger data strings.
FUNCTION The data transmission takes place at 9,600 baud (default value). 1 startbit, 8 databits and 1
stopbit will be transmitted. No parity is available. The drivers are high ohmic. The control
of data is made by the user software.
The interface module can be used for bus connections as well as for point to point
connections. With bus connections, modules that are not connected to the power supply can
also be wired. They do not disturb the bus connection.
UHFHLYHU
WHUPLQDWLRQ
TxD TxD
+ -
RxD RxD
+ -
RxDRxD
+ -
WUDQVPLWWHU
M
M
M
S
S
S
M
S
WUDQVPLWWHUDQG
WUDQVPLWWHUQG
WUDQVPLWWHUDQG
UHFHLYHU
UHFHLYHU
UHFHLYHU
:$*2
:$*2
SRLQWWRSRLQWFRQQHFWLRQ
RS232,TTY,RS485 750-650,651,653
WHUPLQDWLRQ
TxD TxD
+ -
EXVFRQQHFWLRQ
5
:$*2Ç,2Ç6<67(0
Structure of input and output data:
The module is a combined analog input and output module with 2 x 16 bit input and
output data. The transfer of the data to be transmitted and the received data is made via
up to 3 output and 3 input bytes. One control byte and one status byte are used to control
the floating data.
Requests are indicated by a change of a bit. An assigned bit indicates execution by
adopting the value of the request bit.
Up to 3 characters which have been received via interface can be stored in the input
bytes 0 to 2. The output bytes will contain the characters to be sent.
The control byte consists of the following bits:
Bit 7
0
Constant
value
must
always
be 0.
Bit 6
Bit 5
Bit 4
OL2
OL1
OL0
Frames available in output
area, OL2 is always 0.
eg. OL2, OL1, OL0 = 0,1,1
3 characters should be sent
and put into the output.
Control Byte
Bit 3
0
Constant
value must
always be 0.
Bit 2
IR
Initialization
request
Bit 1
RA
Reception
acknowledgement
Bit 0
TR
Transmission
request
Bit 2
IA
Initialization
acknowledgement
Bit 1
RR
Reception
request
Bit 0
TA
Transmission
acknowledgement
The status byte consists of the following bits:
Bit 7
0
Constant
value
must
always
be 0.
Bit 6
Bit 5
Bit 4
IL2
IL1
IL0
Frames available in input
area, IL2 is always 0. eg.
IL2,IL1,IL0 = 0,1,0
2 characters were received
and reside in input 0 and input
1.
RS232,TTY,RS485 750-650,651,653
6
Status Byte
Bit 3
BUF_F
Input buffer
is full.
:$*2Ç,2Ç6<67(0
The PLC is able to control transmission and reception of data by means of the control
byte and the status byte.
Initialization of the module:
•
•
•
•
set IR in the control byte
transmit/receive functions are blocked
output/input buffers are erased
serial interface module will load its configuration data
Transmitting data:
• TR≠TA: put characters into output byte 0 to 2
• amount of characters is specified in OL0 to OL2
• TR is inverted and read out
• characters are put into output buffer if TR=TA
Receiving data:
• RR≠RA: in input byte 0 to 2 characters are available
• amount of characters is specified in IL0 to IL2
• charactersin IL0 to IL2 are read out
• RA is inverted and read out
• all characters are read when RR=RA
The transmitting and receiving of data can be done simultaneously. The initialization
request has prioirity and will stop transmitting and receiving of data immediately.
Message: input buffer full (Bit 3)
Input buffer is full. Data which are received now are lost.
RS232,TTY,RS485 750-650,651,653
7
:$*2Ç,2Ç6<67(0
Examples:
The module is initialized.
- The initialization bit in the control byte is set.
Output byte 0
0x00
Control byte Output byte 2
0000.0100 0x00
Output byte 1
0x00
- After the initialization has been executed, the status byte will give back 000.0100.
Input byte 0
XX
XX
Status byte
0XXX.X0XX
0XXX.X1XX
Input byte 2
XX
XX
Input byte 1
Module is still being reset
XX
Initialization completed
XX
Sending of the data string “Hello”:
- The first 3 characters and the buffer length of 3 are transmitted.
Output byte 0
‘H’ (0 x 48)
Control byte
0011.0000
Output byte 2
‘l’ (0 x 6C)
Output byte 1
‘e’ (0 x 65)
- The transmission request bit (TR) is inverted.
Output byte 0
‘H’
Control byte
0011.0001
Output byte 2
‘l’
Output byte 1
‘e’
- As soon as TR=TA, the rest of the data can be sent.
Input byte 0
XX
XX
Status byte
0XXX.XXX
0
0XXX.XXX
1
Input byte 2
XX
Input byte 1
The data is still being transferred.
XX
XX
XX
Data transfer completed.
- The last 2 characters and the buffer length of 2 are transmitted.
Output byte 0
‘l’
Control byte
0010.0001
Output byte 2
XX
Output byte 1
‘o’ (0 x 6F)
- The transmission request bit (TR) is inverted.
Output byte 0
‘l’
RS232,TTY,RS485 750-650,651,653
Control byte
0010.0000
Output byte 2 Output byte 1
XX
‘o’
8
:$*2Ç,2Ç6<67(0
- As soon as TA = TR, the data has been transferred to the output buffer.
Input byte 0 Status byte
Input byte 2 Input byte 1
The data is still being transferred.
XX
0XXX.XXX1 XX
XX
Data transfer completed.
XX
0XXX.XXX0 XX
XX
Receiving the character chain “WAGO”
- As soon as RA≠RR, the input bytes contain data.
Output byte 0
XX
Input byte 0
XX
‘W’ (0 x 57)
Control yte
Output byte 2
0XXX.000X XX
Status byte
Input byte 2
0XXX.0X0X XX
0011.0X1X ‘G’ (0 x 47)
Output byte 1
XX
Input byte 1
XX
‘A’ (0 x 41)
No received data available.
The information is in the input bytes.
- After the 3 characters have been processed, RA is inverted.
Output byte 0
XX
Control byte Output byte 2
0XXX.001X XX
Output byte 1
XX
- If RA≠RR, the receiving of additional characters will continue.
Input byte 0
XX
‘O’ (0 x 4F)
Status byte
Input byte 2
0XXX.0X1X XX
0001.0X0X XX
Input byte 1
No received data available.
XX
The information is in the input bytes.
XX
- After the characters have been processed, RA is inverted.
Output byte 0
XX
Notes:
Control byte
0XXX.000X
Output byte
XX
Output byte
XX
0 x 23 is a hexadecimal value
0101.1001 is a binary value
An X indicates that this particular value has no importance.
XX indicates that the whole value has no importance.
Status Indicators:
The 3 green LEDs have the following function:
Function
Output Status TxD
RS232,TTY,RS485 750-650,651,653
Non-Function
Input Status RxD
9
:$*2Ç,2Ç6<67(0
Structure of the in and output data for Interbus
The module is a combined input and output module with 2 x 16 bit input and output
data.
Outputs:
Word
D0 (bit 0-15)
D1(bit16-31)
Description
Output byte0
Output byte2
Control byte
Output byte1
Inputs:
Word
D0 (bit 0-15)
D1(bit16-31)
Description
Input byte0
Input byte2
Status byte
Input byte1
The RS232 module is also available with a data format of 5 bytes (item-no. 750650/000-001).
Outputs:
Word
D0 (bit 0-15)
D1(bit16-31)
D2(bit32-47)
Description
Control byte
Output byte1
Output byte3
Output byte0
Output byte2
Output byte4
Inputs:
Word
D0 (bit 0-15)
D1(bit16-31)
D2(bit32-47)
Description
Status byte
Input byte1
Input byte3
Input byte0
Input byte2
Input byte4
RS232,TTY,RS485 750-650,651,653
11
:$*2Ç,2Ç6<67(0
Data exchange module
PN 750-654
Technical Description
This technical description is only valid for hardware and software versionx X X X X 2
C 0 0 - - - -. The product series number is printed on the right side of the module.
The operational mode described below is for the factory preset mode.
The following description is preliminary and is applicable to the factory configuration.
Many other operational modes are possible (please contact WAGO for the
corresponding settings.)
Attention:
Some modules do not provide all power jumper contacts (e.g. 4-channel)! A module
which needs all contacts (e.g. 2-channel digital) cannot be connected to the right hand
side of modules which do not have 3 power jumper contacts.
The data exchange module is able to run with all :$*2Ç,2Ç6<67(0
buscouplers (except for the economy type).
Data exchange module 750-654
1
:$*2Ç,2Ç6<67(0
Technical Data
Series 750-
654
Bit transmission
via 2 twisted pair with differential signals
120 Ω
Transmission channel
Transmission rate
Resistance of cable
Current Consumption (internal)
Transmission length
Input buffer
Output buffer
Voltage supply
Isolation
Bit width internal
Configuration
Operating temperature
Wire connection
Dimensions (mm) W x H x L
Factory preset
internal bit width
Data exchange module 750-654
TxD and RxD, full duplex, 2 channel
62500 Baud
65 mA max.
max. 100 m twisted pair
128 Byte
16 Byte
via internal system
500 V System/Supply
1 x 40 bits, 1 x 8 bits control/status
none, parameter configuration with software
0 °C ... + 55 °C
CAGE CLAMP; 0.08 to 2.5 mm²
12 x 64* x 100 (*from upper edge of the carrier rail)
1 x 32 bits in/out, 1 x 8 bits control/status
2
:$*2Ç,2Ç6<67(0
Description of data exchange module
The data exchange module allows the exchange of 4 (5) bytes between different fieldbus
systems via multiplexing of a serial connection. The delay which is caused by the
multiplexor is < 5ms. The integrated watchdog function switches all outputs to zero if
there is no valid information for more than 200 ms via the multiplex connection.
The 128 bytes input buffer provides for high rates of data transmission. When using
lower rates of transmission speed you can collect the received data, with less priority,
without loosing data.
The 16 byte output buffer provides for faster transmission of larger data strings.
The data exchange module is connected peer-to-peer. For the wiring of the serial
multiplex connection the RxD and TxD cables are crossed. The following illustrations
show the peer-to-peer connection and the internal structure of the data exchange
module.
TxD TxD
+
-
TxD TxD
+
-
RxD RxD
+
-
RxD RxD
+
-
M
M
M
M
S
S
S
S
:$*2
:$*2
SHHUWRSHHUFRQQHFWLRQ
Input byte0
7 6 5 4 3 2 1 0
9
N
Internal
control system
RxD+
Input byte1
N
7 6 5 4 3 2 1 0
RxD-
Input byte2
TxD+
7 6 5 4 3 2 1 0
(1
Input byte3
TxDM
7 6 5 4 3 2 1 0
S
Input byte4
7 6 5 4 3 2 1 0
Output byte0
7 6 5 4 3 2 1 0
Output byte1
7 6 5 4 3 2 1 0
Output byte2
7 6 5 4 3 2 1 0
Output byte3
7 6 5 4 3 2 1 0
Data exchange module 750-654
Output byte4
Control byte
Statusbyte
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
7 6 5 4 3 2 1 0
3
:$*2Ç,2Ç6<67(0
Structure of input and output data:
The module is a combined special function input and output module with 1 x 32 (40) Bit
input and output data. The tranfer of the data to be transmitted and the received data is
made via up to 5 input and 5 output Bytes. One control byte and one status byte are used
to control the floating data.
The control byte consists of the following bits:
Control byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
Constant value
always must be 0
The status byte consists of the following bits:
Status byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
RCVT1
RCVT2
CHK
OVR
PAR
Constant
value
always
must be
0.
Module is in timeout.
All output bits are set
to 0 (watchdog).
The receiver is in
timeout.
Checksum
error.
Buffer
Pariry error or
overflow wrong data in
a frame.
The PLC is able to control transmission and reception of data by means of the control
byte and the status byte.
Control of the multiplex connection: In the process image of the transmitting
buscoupler one Bit is set to „1“ for the whole time. As long as this Bit is „1“ in the
receiving coupler, further input Bits can be evaluated. If the Bit is „0“ the multiplex
connection has been disrupted. The further Bits are also 0 because of the watchdog.
Control of the multiplex connection with acknowledge: If the transmitting
buscoupler gets an acknowledge from the receiving buscoupler, the received bit must be
transfered as an output bit to the process image. The transmission is successful as long
as the Bit is „1“.
Handshake: If a serial data exchange should be made with the data exchange module,
the handshake can be made via „Toggle Bits“. Therefore an input bit and an output bit
are reserved. As soon as those bits are different from each other, a request from the
opposite module is made. As soon as the request is executed the output bit is toggled.
Data exchange module 750-654
4
:$*2Ç,2Ç6<67(0
Structure of the in- and output data for Profibus (from firmware WH)
The ID 179 (hex: 0xB3), ( Data consistence over 4 Byte) is used.
Outputs
Byte
D0
D1
D2
D3
Description
Output byte0
Output byte1
Output byte2
Output byte3
Inputs
Byte
D0
D1
D2
D3
Description
Input byte0
Input byte1
Input byte2
Input byte3
For the ID 188 (hex.: 0xBC), Data consistence over 6 Byte is used, input and output data
are now as follows:
Outputs
Byte
D0
D1
D2
D3
D4
D5
Description
Control byte
Output byte0
Output byte1
Output byte4
Output byte2
Output byte3
Inputs
Byte
D0
D1
D2
D3
D4
D5
Description
Statusbyte
Input byte0
Input byte1
Input byte4
Input byte2
Input byte3
For a S7 PLC the function code SFC14 and SFC15 must be used because the data length
is more than 4.
Attention:
The control byte allows the changing of the registers of the module. It must always be 0
in order to avoid a change in the registers. A wrong mapping can change the function of
the module!
Data exchange module 750-654
5
:$*2Ç,2Ç6<67(0
Structure of the in- and output data for InterBus S (from firmware
WF)
The module is a combined special function input and output module with 2 x 16 Bit inand output data.
Input
Word
n (Bit0-Bit15)
n+1 (Bit16-Bit31)
Description
High
Input byte0
Input byte2
Low
Input byte1
Input byte3
Description
High
Output byte0
Output byte2
Low
Output byte1
Output byte3
Output
Word
n (Bit0-Bit15)
n+1 (Bit16-Bit31)
Attention:
For Interbus S the data is written in Motorola format (high Byte first). In connection
with other fieldbus systems the Bytes in the data word are changed.
Attention:
The control byte allows the changing of the registers of the module. It must always be 0
in order to avoid a change in the registers. A wrong mapping can change the function of
the module!
Data exchange module 750-654
5
:$*2Ç,2Ç6<67(0
Structure of the in- and output data for DeviceNet (from firmware
306V2.2)
The module has 6 Bytes input and output data in the Poll I/O data. Consumed (Tx for
the Scanner) and produced (Rx for the Scanner) data size are each 6 Byte more.
Input
Byte
D0
D1
D2
D3
D4
D5
Description
Control byte
Input byte1
Input byte0
Input byte4
Input byte3
Input byte2
Output
Byte
D0
D1
D2
D3
D4
D5
Description
Status byte
Input byte1
Input byte0
Input byte4
Input byte3
Input byte2
Attention:
The control byte allows the changing of the registers of the module. It must always be 0
in order to avoid a change in the registers. A wrong mapping can change the function of
the module!
Structure of the in- and output data for DeviceNet (from firmware
306V3.0)
The module has 4 Bytes input and output data in the polled I/O data.
Input
Byte
D0
D1
D2
D3
Description
Input byte0
Input byte1
Input byte2
Input byte3
Output
Byte
D0
D1
D2
D3
Description
Input byte0
Input byte1
Input byte2
Input byte3
Data exchange module 750-654
5
:$*2Ç,2Ç6<67(0
Structure of the in- and output data for Modbus (from firmware V2.3)
The module is a combined special function input and output module with 2 x 16 Bit inand output data.
Input
Word
n (Bit0-Bit15)
n+1 (Bit16-Bit31)
Description
High
Input byte0
Input byte2
Low
Input byte1
Input byte3
Description
High
Output byte0
Output byte2
Low
Output byte1
Output byte3
Output
Word
n (Bit0-Bit15)
n+1 (Bit16-Bit31)
Attention:
For Interbus S the data is written in Motorola format (high Byte first). In connection
with other fieldbus systems the Bytes in the data word are changed.
Attention:
The control byte allows the changing of the registers of the module. It must always be 0
in order to avoid a change in the registers. A wrong mapping can change the function of
the module!
Data exchange module 750-654
5
:$*2Ç,2Ç6<67(0
Structure of the in- and output data for CanOpen (from firmware WI)
The module is in the list with Index 0x2400 (input) and Index 0x2500 (output). The
module has 2 subindexes.
2 Byte special modules, Inputs
Idx
2400
SIdx
0
....
n
Name
special 2 byte input
....
Input byte0, Input
byte1
Type
Unsigned8
....
Unsigned16
Attrib.
ro
....
ro
n+1
Input byte2, Input
byte3
Unsigned16 ro
....
....
....
....
0xFF 0xFF. Special input Unsigned16 ro
Default
none
....
none, 0x0
for WD
error
none, 0x0
for WD
error
....
none
Description
number of 2 Byte channels
....
1. and 2. Input byte
3. and 4. Input byte
....
255. Input channel
2 Byte special modules, Outputs
Idx
2500
SIdx
0
Name
special 2 byte
output
....
....
n
Output byte0,
Output byte1
n+1 Output byte2,
Output byte3
....
....
0xFF 0xFF. special
output
Type
Unsigned8
Attrib. Default
ro
none
Description
number of 2 Byte channels
....
....
Unsigned16 rw
....
none
....
1. and 2. Output byte
Unsigned16 rw
none
3. and 4. Output byte
....
....
Unsigned16 rw
....
none
....
255. Outputkanal
Attention:
The control byte allows the changing of the registers of the module. It must always be 0
in order to avoid a change in the registers. A wrong mapping can change the function of
the module!
Data exchange module 750-654
5
:$*2Ç,2Ç6<67(0
Structure of the in- and output data for CAL (from firmware WE)
Mode class 4:
The data is in the 2 Byte objects #BK_AI2W0_XXX, #BK_AI2W1_XXX and
#BK_A02W0_XXX. Each module has 2 values.
Input
Mux
n
n+1
Content
Input byte0, Input byte1
Input byte2, Input byte3
Description
1. and 2. Input byte
3. and 4. Input byte
Content
Output byte0, Output byte1
Output byte2, Output byte3
Description
1. and 2. Output byte
3. and 4. Output byte
Output
Mux
n
n+1
Mode class 0:
The description of the data is the same as for class 4 mode. The data is put into objects
No.1, No.2 and No.3 (read/write 2 Byte analog).
Attention:
The control byte allows the changing of the registers of the module. It must always be 0
in order to avoid a change in the registers. A wrong mapping can change the function of
the module!
Data exchange module 750-654
5
:$*2Ç,2Ç6<67(0
Structure of the in- and output data for LIGHTBUS (from firmware
WD)
Input
Word
n
n+1
n+2
n+3
Content
High
Input byte0
Input byte3
Low
Statusbyte
Input byte1
Input byte4
Input byte2
Description
Content
High
Output byte0
Output byte3
Low
Statusbyte
Output byte1
Output byte4
Output byte2
Statusword
1. and 2. Input byte
5.Input byte
3. and 4. Input byte
Output
Word
n
n+1
n+2
n+3
Description
Statusword
1. and 2. Output byte
5.Output byte
3. and 4. Output byte
Attention:
The control byte allows the changing of the registers of the module. It must always be 0
in order to avoid a change in the register. A wrong mapping can change the function of
the module!
Data exchange module 750-654
5
:$*2Ç,2Ç6<67(0
Use in Hazardous Environments • 1
Identification
Use in Hazardous Environments
The WAGO-I/O-SYSTEM 750 (electrical equipment) is designed for use in
Zone 2 hazardous areas.
The following sections include both the general identification of components
(devices) and the installation regulations to be observed. The individual
subsections of the "Installation Regulations" section must be taken into account if
the I/O module has the required approval or is subject to the range of application
of the ATEX directive.
WAGO-I/O-SYSTEM 750
2 •
Use in Hazardous Environments
Identification
Identification
For Europe according to CENELEC and IEC
Figure 1: Example for lateral labeling of bus modules
Figure 2: Printing on text detail in accordance with CENELEC and IEC
Table 1: Description of Printing on
Printing on Text
DEMKO 08 ATEX 142851 X
IECEx PTB 07.0064X
I M2 / II 3 GD
Ex nA
IIC
T4
Description
Approval body and/or number of the examination
certificate
Explosion protection group and Unit category
Type of ignition and extended identification
Explosion protection group
Temperature class
WAGO-I/O-SYSTEM 750
Use in Hazardous Environments • 3
Identification
Figure 3: Example of side marking of Ex i and IEC Ex i approved I/O modules
Figure 4: Inscription text detail acc. CENELEC and IEC
WAGO-I/O-SYSTEM 750
4 •
Use in Hazardous Environments
Identification
Table 2: Description of the inscription
Inscription text
TÜV 07 ATEX 554086 X
TUN 09.0001X
Dust
II
3(1)D
Ex
tD
[iaD]
A22
IP6X
T 135°C
Mining
I
(M2)
[Ex ia]
I
Gases
II
3(1)G
Ex
nA
[ia]
IIC
T4
Description
Approving authority or
certificate numbers
Device group: All except mining
Device category: Zone 22 device (Zone 20 subunit)
Explosion protection mark
Protection by enclosure
Approved in accordance with "Dust intrinsic safety"
standard
Surface temperature determined according to
Procedure A, use in Zone 22
Dust-tight (totally protected against dust)
Max. surface temp. of the enclosure (no dust bin)
Device group: Mining
Device category: High degree of safety
Explosion protection: Mark with category of type of
protection intrinsic safety: Even safe when two
errors occur
Device group: Mining
Device group: All except mining
Device category: Zone 2 device (Zone 0 subunit)
Explosion protection mark
Type of protection: Non-sparking operating
equipment
Category of type of protection intrinsic safety: Even
safe when two errors occur
Explosion Group
Temperature class: Max. surface temperature 135°C
WAGO-I/O-SYSTEM 750
Use in Hazardous Environments • 5
Identification
For America according to NEC 500
Figure 5: Example for lateral labeling of bus modules
Figure 6: Printing on text detail in accordance with NEC
Table 3: Description of Printing on
Printing on Text
CL 1
DIV 2
Grp. ABCD
Optemp code T4
WAGO-I/O-SYSTEM 750
Description
Explosion protection group (condition of use
category)
Area of application (zone)
Explosion group (gas group)
Temperature class
6 •
Use in Hazardous Environments
Installation Regulations
Installation Regulations
In the Federal Republic of Germany, various national regulations for the
installation in explosive areas must be taken into consideration. The basis for this
forms the working reliability regulation, which is the national conversion of the
European guideline 99/92/E6. They are complemented by the installation
regulation EN 60079-14. The following are excerpts from additional VDE
regulations:
Table 4: VDE Installation Regulations in Germany
DIN VDE 0100 Installation in power plants with rated voltages up to 1000 V
DIN VDE 0101 Installation in power plants with rated voltages above 1 kV
DIN VDE 0800 Installation and operation in telecommunication plants including
information processing equipment
DIN VDE 0185 lightning protection systems
The USA and Canada have their own regulations. The following are excerpts
from these regulations:
Table 5: Installation Regulations in USA and Canada
NFPA 70
National Electrical Code Art. 500 Hazardous Locations
ANSI/ISA-RP 12.6-1987 Recommended Practice
C22.1
Canadian Electrical Code
Notice the following points
When using the WAGO-I/O SYSTEM 750 (electrical operation) with Ex
approval, the following points are mandatory:
WAGO-I/O-SYSTEM 750
Use in Hazardous Environments • 7
Installation Regulations
Special Conditions for Safe Operation of the ATEX and IEC
Ex (acc. DEMKO 08 ATEX 142851X and IECEx PTB 07.0064)
The fieldbus-independent I/O modules of the WAGO-I/O-SYSTEM 750-.../...-...
must be installed in an environment with degree of pollution 2 or better. In the
final application, the I/O modules must be mounted in an enclosure with IP 54
degree of protection at a minimum with the following exceptions:
-
I/O modules 750-440, 750-609 and 750-611 must be installed in an IP 64
minimum enclosure.
I/O module 750-540 must be installed in an IP 64 minimum enclosure for
230 V AC applications.
I/O module 750-440 may be used up to max. 120 V AC.
When used in the presence of combustible dust, all devices and the enclosure shall
be fully tested and assessed in compliance with the requirements of IEC 612410:2004 and IEC 61241-1:2004.
When used in mining applications the equipment shall be installed in a suitable
enclosure according to EN 60079-0:2006 and EN 60079-1:2007.
I/O modules fieldbus plugs or fuses may only be installed, added, removed or
replaced when the system and field supply is switched off or the area exhibits no
explosive atmosphere.
DIP switches, coding switches and potentiometers that are connected to the I/O
module may only be operated if an explosive atmosphere can be ruled out.
I/O module 750-642 may only be used in conjunction with antenna 758-910 with
a max. cable length of 2.5 m.
To exceed the rated voltage no more than 40%, the supply connections must have
transient protection.
The permissible ambient temperature range is 0 °C to +55 °C.
WAGO-I/O-SYSTEM 750
8 •
Use in Hazardous Environments
Installation Regulations
Special conditions for safe use (ATEX Certificate TÜV 07
ATEX 554086 X)
1.
For use as Gc- or Dc-apparatus (in zone 2 or 22) the field bus independent
I/O modules WAGO-I/O-SYSTEM 750-*** shall be erected in an enclosure
that fulfils the requirements of the applicable standards (see the marking)
EN 60079-0, EN 60079-11, EN 60079-15, EN 61241-0 and EN 61241-1.
For use as group I, electrical apparatus M2, the apparatus shall be erected in
an enclosure that ensures a sufficient protection according to EN 60079-0
and EN 60079-1 and the degree of protection IP64. The compliance of these
requirements and the correct installation into an enclosure or a control
cabinet of the devices shall be certified by an ExNB.
2.
If the interface circuits are operated without the field bus coupler station
type 750-3../…-… (DEMKO 08 ATEX 142851 X), measures must be taken
outside of the device so that the rating voltage is not being exceeded of
more than 40% because of transient disturbances.
3.
DIP-switches, binary-switches and potentiometers, connected to the module
may only be actuated when explosive atmosphere can be excluded.
4.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted during installation, for maintenance or for repair purposes.
The temporal coincidence of explosion hazardous atmosphere and
installation, maintenance resp. repair purposes shall be excluded.
5.
For the types 750-606, 750-625/000-001, 750-487/003-000, 750-484 the
following shall be considered: The interface circuits shall be limited to
overvoltage category I/II/III (non mains/mains circuits) as defined in IEC
60664-1.
6.
For the type 750-601 the following shall be considered: Do not remove or
replace the fuse when the apparatus is energized.
7.
The ambient temperature range is: 0°C ≤ Ta ≤ +55°C (for extended details
please note certificate).
WAGO-I/O-SYSTEM 750
Use in Hazardous Environments • 9
Installation Regulations
Special conditions for safe use (IEC-Ex Certificate TUN
09.0001 X)
1.
For use as Dc- or Gc-apparatus (in zone 2 or 22) the fieldbus independent
I/O modules WAGO-I/O-SYSTEM 750-*** shall be erected in an enclosure
that fulfils the requirements of the applicable standards (see the marking)
IEC 60079-0, IEC 60079-11, IEC 60079-15, IEC 61241-0 and IEC 61241-1.
For use as group I, electrical apparatus M2, the apparatus shall be erected in
an enclosure that ensures a sufficient protection according to IEC 60079-0
and IEC 60079-1 and the degree of protection IP64. The compliance of
these requirements and the correct installation into an enclosure or a control
cabinet of the devices shall be certified by an ExCB.
2.
Measures have to be taken outside of the device that the rating voltage is not
being exceeded of more than 40% because of transient disturbances.
3.
DIP-switches, binary-switches and potentiometers, connected to the module
may only be actuated when explosive atmosphere can be excluded.
4.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted during installation, for maintenance or for repair purposes.
The temporal coincidence of explosion hazardous atmosphere and
installation, maintenance resp. repair purposes shall be excluded.
5.
For the types 750-606, 750-625/000-001, 750-487/003-000, 750-484 the
following shall be considered: The interface circuits shall be limited to
overvoltage category I/II/III (non mains/mains circuits) as defined in IEC
60664-1.
6.
For the type 750-601 the following shall be considered: Do not remove or
replace the fuse when the apparatus is energized.
7.
The ambient temperature range is: 0°C ≤ Ta ≤ +55°C (for extended details
please note certificate).
WAGO-I/O-SYSTEM 750
10 • Use in Hazardous Environments
Installation Regulations
Special conditions for safe use (ATEX Certificate DEKRA
11ATEX0203 X)
1.
The components shall be installed in a suitable enclosure providing a degree
of protection of at least IP54 according to EN 60529, taking into account the
environmental conditions under which the equipment will be used.
2.
When the temperature under rated conditions exceeds 70 °C at the cable or
conduit entry point, or 80 °C at the branching point of the conductors, the
temperature specification of the selected cable shall be in compliance with
the actual measured temperature values.
3.
Provisions shall be made to prevent the rated voltages from being exceeded
by transient disturbances of more than 40 %.
4.
Components may only be removed or inserted when the system supply and
the field supply are switched off, or when the location is known to be nonhazardous.
5.
Fieldbus connectors may only be disconnected or connected when the
system supply is switched oft, or when the location is known to be nonhazardous.
6.
The fuses, present in the system modules 750-6xx may only be replaced
when the supply is switched off, or when the location is known to be nonhazardous.
7.
Address selectors and ID switches may only be adjusted when the system
supply is switched off, or when the location is known to be non-hazardous.
8.
The ambient temperature range is: 0°C ≤ Ta ≤ +55°C .
WAGO-I/O-SYSTEM 750
Use in Hazardous Environments • 11
Installation Regulations
ANSI/ISA 12.12.01
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or
non-hazardous locations only.
Explosion hazard!
Explosion hazard - substitution of components may impair suitability for Class I,
Div. 2.
Disconnect device when power is off and only in a non-hazardous area!
Do not disconnect equipment unless power has been switched off or the area is
known to be non-hazardous.
When a fuse is provided, the following marking shall be provided:
”A switch suitable for the location where the equipment is installed shall be
provided to remove the power from the fuse”.
The switch need not be integrated in the equipment.
For devices with Ethernet connectors:
”Only for use in LAN, not for connection to telecommunication circuits”.
Use only with antenna module 758-910!
Use Module 750-642 only with antenna module 758-910.
Additional Information
Proof of certification is available on request. Also take note of the information
given on the module technical information sheet. The Instruction Manual,
containing these special conditions for safe use, must be readily available to the
user.
WAGO-I/O-SYSTEM 750
12 • Use in Hazardous Environments
Installation regulations
Pos: 36 /Alle Serien (Allgemeine Module)/Überschriften für alle Serien/Zulassungen - Überschrift 2 @ 3\mod_1224055364109_21.doc @ 24030 @ 2 @ 1
Approvals
Pos: 37 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Zulassungen/Information: Weitere Informationen zu Zulassungen 750-xxxx @ 3\mod_1227190967156_21.doc @ 25221 @ @ 1
More Information about Approvals
Detailed references to the approvals are listed in the document "Overview
Approvals WAGO-I/O-SYSTEM 750", which you can find on the DVD
“AUTOMATION Tools and Docs” (Item-No.: 0888-0412) or via the internet
under: www.wago.com  Service  Documentation  WAGO-I/O-SYSTEM
750  System Description.
Pos: 38 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Zulassungen/Zulassungen Busklemme 750-xxxx Allgemein, ohne Variantenangabe @ 4\mod_1237460656921_21.doc @ 28643 @ @ 1
The following approvals have been granted to 750-334 INTERBUS Fieldbus Coupler:
Pos: 39.1 /Alle Serien (Allgemeine Module)/Zulassungen/Standardzulassungen/CE (Konformitätskennzeichnung) @ 3\mod_1224494777421_21.doc @ 24276 @ @ 1
Conformity Marking
Pos: 39.2 /Alle Serien (Allgemeine Module)/Zulassungen/Standardzulassungen/cULus (UL508) @ 3\mod_1224055013140_0.doc @ 24020 @ @ 1
CULUS
(UL508)
Pos: 39.3 /Dokumentation allgemein/Gliederungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.doc @ 24460 @ @ 1
Pos: 40 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Zulassungen/Zulassungen Busklemme 750-xxxx Ex, ohne Variantenangabe @ 4\mod_1237191218000_21.doc @ 28423 @ @ 1
The following Ex approvals have been granted to 750-334 INTERBUS Fieldbus Coupler:
DEKRA
II 3 G Ex nA II T4
8&,((%5([Q$,,7
Pos: 41 /Alle Serien (Allgemeine Module)/Zulassungen/Ex Zulassungen/DEKRA (II 3 G Ex nA II T4) @ 11\mod_1326101612316_0.doc @ 85350 @ @ 1
Pos: 42 /Dokumentation allgemein/Gliederungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.doc @ 24460 @ @ 1
Pos: 43 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Zulassungen/Zulassungen Busklemme 750-xxxx Schiff, ohne Variantenanga
Pos: 44 /Alle Serien (Allgemeine Module)/Zulassungen/Schiffszulassungen/GL (Germanischer Lloyd) Cat. A, B, C, D (EMC 1) @ 3\mod_1224492724484_0.doc @ 24228 @ @ 1
CULUS (ANSI/ISA 12.12.01)
Class I Div2 ABCD T4
Pos: 45 /Dokumentation allgemein/Gliederungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.doc @ 24460 @ @ 1
Pos: 46 /Alle Serien (Allgemeine Module)/Überschriften für alle Serien/Normen und Richtlinien - Überschrift 2 @ 4\mod_1242804031875_21.doc @ 33646 @ 2 @ 1
Standards and Guidelines
Pos: 47 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Normen und Richtlinien/EMV-Normen Busklemme 750-xxxx, ohne Variantenangabe @ 4\mod_1242803944015_21.doc @ 33642 @ @ 1
750-334 INTERBUS Fieldbus Coupler meet the following requirements
on emission and immunity of interference:
Pos: 48 /Alle Serien (Allgemeine Module)/Normen und Richtlinien/EMV CE-Störaussendung EN 61000-6-4: 2007 @ 4\mod_1242798273984_21.doc @ 33602 @ @ 1
EMC CE-Emission of interference
acc. to EN 61000-6-4: 2007
Pos: 49 /Alle Serien (Allgemeine Module)/Normen und Richtlinien/EMV CE-Störfestigkeit EN 61000-6-2: 2005 @ 4\mod_1242797655625_21.doc @ 33591 @ @ 1
EMC CE-Immunity to interference
acc. to EN 61000-6-2: 2005
Po
11\mod_1327323590372_21.doc @ 86880 @ @ 1
ATEX guideline
Po
Pos: 52 /Alle Serien (Allgemeine Module)/Normen und Richtlinien/ATEX-Richtlinie EN 60079-0: 2006 und E N 60079-15: 2005 @
Pos: 53 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1
WAGO-I/O-SYSTEM 750
Modular I/O-System
acc. to EN 60079-0: 2006 and
acc. to EN 60079-15: 2005
WAGO Kontakttechnik GmbH
Postfach 2880 • D-32385 Minden
Hansastraße 27 • D-32423 Minden
Phone:
05 71/8 87 – 0
Fax:
05 71/8 87 – 1 69
E-Mail:
info@wago.com
Internet:
http://www.wago.com