Dual Digital Media Player
DN-D4500MK2
Owner’s Manual
FCC INFORMATION
(For US customers)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
1.PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this product may not cause harmful interference, and (2) this product must accept
any interference received, including interference that may cause undesired operation.
CAUTION:
O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
T
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC
requirements. Modification not expressly approved by DENON may void your authority, granted by
the FCC, to use the product.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
3.NOTE
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
IMPORTANT TO SAFETY
WARNING:
•
•
•
To reduce the risk of fire and electric shock, this apparatus should not be exposed
to rain or moisture.
•
CAUTION:
This product has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This product generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
product does cause harmful interference to radio or television reception, which can be determined
by turning the product OFF and ON, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the product into an outlet on a circuit different from that to which the receiver is
connected.
Consult the local retailer authorized to distribute this type of product or an experienced radio/TV
technician for help.
For Canadian customers:
This Class B apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT
PROPERLY QUALIFIED SERVICE PERSONNEL.
I
IMPORTANT SAFETY INSTRUCTIONS
nnLaser Class
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
ADVARSEL:
VAROITUS!
VARNING:
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
CLASS 1
,,
LASER PRODUCT
,,
(IEC60825-1:2007)
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
1. Read these instructions.
USYNLIG LASERSTRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.
UNDGÅ UDSAETTELSE FOR STRÅLING.
LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄMTTÖMÄLLE LASERSÄTEILYLLE.
OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN
UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING SOM
ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
ATTENZIONE: QUESTO APPARECCHIO E’ DOTATO DI DISPOSITIVO OTTICO CON RAGGIO LASER.
L’USO IMPROPRIO DELL’APPARECCHIO PUO’ CAUSARE PERICOLOSE ESPOSIZIONI A RADIAZIONI!
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
CAUTION
13.Unplug this apparatus during lightning storms or when unused for long
periods of time.
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric
shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the
plug attachment and not by pulling the cord.
2. Do not open the rear cover
In order to prevent electric shock, do not open the top cover.
If problems occur, contact your DENON DEALER.
3. Do not place anything inside
Do not place metal objects or spill liquid inside the system.
Electric shock or malfunction may result.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin.
This plug will only fit into a grounding-type power outlet.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the grounding-type plug.
Please, record and retain the Model name and serial number of your set shown on the rating label.
Model No. DN-D4500MK2
Serial No.
II
nnNOTE ON USE/HINWEISE ZUM GEBRAUCH/OBSERVATIONS RELATIVES A L’UTILISATION/
NOTE SULL’USO/NOTAS SOBRE EL USO/ALVORENS TE GEBRUIKEN/OBSERVERA
WARNINGS
WARNHINWEISE
AVERTISSEMENTS
AVVERTENZE
ADVERTENCIAS
WAARSCHUWINGEN
VARNINGAR
•Handle the power cord carefully.
Hold the plug when unplugging
the cord.
•Keep the unit free from
moisture, water, and dust.
•Unplug the power cord when
not using the unit for long
periods of time.
•Do not obstruct the ventilation
holes.
•Do not let foreign objects into
the unit.
•Do not let insecticides,
benzene, and thinner come in
contact with the unit.
•Never disassemble or modify
the unit in any way.
•Ventilation should not be
impeded by covering the
ventilation openings with
items, such as newspapers,
tablecloths or curtains.
•Naked flame sources such as
lighted candles should not be
placed on the unit.
•Do not expose the unit to
dripping or splashing fluids.
•Do not place objects filled with
liquids, such as vases, on the
unit.
•Do not handle the mains cord
with wet hands.
•When the switch is in the OFF
position, the equipment is not
completely switched off from
MAINS.
•The equipment shall be
installed near the power supply
so that the power supply is
easily accessible.
•Gehen Sie vorsichtig mit dem
Netzkabel um.
Halten Sie das Kabel am
Stecker, wenn Sie den Stecker
herausziehen.
•Halten Sie das Gerät von
Feuchtigkeit, Wasser und Staub
fern.
•Decken Sie den Lüftungsbereich
nicht ab.
•Wenn das Gerät längere Zeit
nicht verwendet werden soll,
trennen Sie das Netzkabel vom
Netzstecker.
•Lassen Sie keine fremden
Gegenstände in das Gerät
kommen.
•Lassen Sie das Gerät nicht
mit Insektiziden, Benzin oder
Verdünnungsmitteln in Berührung
kommen.
•Versuchen Sie niemals das Gerät
auseinander zu nehmen oder zu
verändern.
•Die Belüftung sollte auf keinen
Fall durch das Abdecken der
Belüftungsöffnungen durch
Gegenstände wie beispielsweise
Zeitungen, Tischtücher, Vorhänge
o. Ä. behindert werden.
•Auf dem Gerät sollten keinerlei
direkte Feuerquellen wie
beispielsweise angezündete
Kerzen aufgestellt werden.
•Das Gerät sollte keiner tropfenden
oder spritzenden Flüssigkeit
ausgesetzt werden.
•Auf dem Gerät sollten keine mit
Flüssigkeit gefüllten Behälter wie
beispielsweise Vasen aufgestellt
werden.
•Das Netzkabel nicht mit feuchten
oder nassen Händen anfassen.
•Wenn der Schalter ausgeschaltet
ist (OFF-Position), ist das Gerät
nicht vollständig vom Stromnetz
(MAINS) abgetrennt.
•Das Gerät sollte in der Nähe einer
Netzsteckdose aufgestellt werden,
damit es leicht an das Stromnetz
angeschlossen werden kann.
•Manipuler le cordon
d’alimentation avec précaution.
Tenir la prise lors du
débranchement du cordon.
•Protéger l’appareil contre
l’humidité, l’eau et la poussière.
•Débrancher le cordon
d’alimentation lorsque l’appareil
n’est pas utilisé pendant de
longues périodes.
•Ne pas obstruer les trous
d’aération.
•Ne pas laisser des objets
étrangers dans l’appareil.
•Ne pas mettre en contact des
insecticides, du benzène et un
diluant avec l’appareil.
•Ne jamais démonter ou
modifier l’appareil d’une
manière ou d’une autre.
•Ne pas recouvrir les orifices
de ventilation avec des objets
tels que des journaux, nappes
ou rideaux. Cela entraverait la
ventilation.
•Ne jamais placer de flamme
nue sur l'appareil, notamment
des bougies allumées.
•L’appareil ne doit pas être
exposé à l’eau ou à l’humidité.
•Ne pas poser d’objet contenant
du liquide, par exemple un
vase, sur l’appareil.
•Ne pas manipuler le cordon
d’alimentation avec les mains
mouillées.
•Lorsque l’interrupteur est sur
la position OFF, l’appareil n’est
pas complètement déconnecté
du SECTEUR (MAINS).
•L’appareil sera installé près de
la source d’alimentation, de
sorte que cette dernière soit
facilement accessible.
•Manneggiate il cavo di
alimentazione con attenzione.
Tenete ferma la spina quando
scollegate il cavo dalla presa.
•Tenete l’unità lontana
dall’umidità, dall’acqua e dalla
polvere.
•Scollegate il cavo di
alimentazione quando
prevedete di non utilizzare
l’unità per un lungo periodo di
tempo.
•Non coprite i fori di
ventilazione.
•Non inserite corpi estranei
all’interno dell’unità.
•Assicuratevi che l’unità non
entri in contatto con insetticidi,
benzolo o solventi.
•Non smontate né modificate
l’unità in alcun modo.
•Le aperture di ventilazione
non devono essere ostruite
coprendole con oggetti, quali
giornali, tovaglie, tende e così
via.
•Non posizionate sull’unità
fiamme libere, come ad
esempio candele accese.
•L’apparecchiatura non deve
essere esposta a gocciolii o
spruzzi.
•Non posizionate sull’unità alcun
oggetto contenente liquidi,
come ad esempio i vasi.
•Non toccare il cavo di
alimentazione con le mani
bagnate.
•Quando l’interruttore
è nella posizione OFF,
l’apparecchiatura non è
completamente scollegata da
MAINS.
•L’apparecchio va installato
in prossimità della fonte di
alimentazione, in modo che
quest’ultima sia facilmente
accessibile.
•Maneje el cordón de energía
con cuidado.
Sostenga el enchufe cuando
desconecte el cordón de
energía.
•Mantenga el equipo libre de
humedad, agua y polvo.
•Desconecte el cordón de
energía cuando no utilice el
equipo por mucho tiempo.
•No obstruya los orificios de
ventilación.
•No deje objetos extraños
dentro del equipo.
•No permita el contacto
de insecticidas, gasolina y
diluyentes con el equipo.
•Nunca desarme o modifique el
equipo de ninguna manera.
•La ventilación no debe quedar
obstruida por haberse cubierto
las aperturas con objetos
como periódicos, manteles o
cortinas.
•No deberán colocarse sobre
el aparato fuentes inflamables
sin protección, como velas
encendidas.
•No exponer el aparato al goteo
o salpicaduras cuando se
utilice.
•No colocar sobre el aparato
objetos llenos de líquido, como
jarros.
•No maneje el cable de
alimentación con las manos
mojadas.
•Cuando el interruptor está en la
posición OFF, el equipo no está
completamente desconectado
de la alimentación MAINS.
•El equipo se instalará cerca
de la fuente de alimentación
de manera que resulte fácil
acceder a ella.
•Hanteer het netsnoer
voorzichtig.
Houd het snoer bij de stekker
vast wanneer deze moet
worden aan- of losgekoppeld.
•Laat geen vochtigheid,
water of stof in het apparaat
binnendringen.
•Neem altijd het netsnoer uit
het stopkontakt wanneer het
apparaat gedurende een lange
periode niet wordt gebruikt.
•De ventilatieopeningen mogen
niet worden beblokkeerd.
•Laat geen vreemde
voorwerpen in dit apparaat
vallen.
•Voorkom dat insecticiden,
benzeen of verfverdunner met
dit toestel in contact komen.
•Dit toestel mag niet
gedemonteerd of aangepast
worden.
•De ventilatie mag niet
worden belemmerd door
de ventilatieopeningen af
te dekken met bijvoorbeeld
kranten, een tafelkleed of
gordijnen.
•Plaats geen open vlammen,
bijvoorbeeld een brandende
kaars, op het apparaat.
•Stel het apparaat niet bloot aan
druppels of spatten.
•Plaats geen voorwerpen gevuld
met water, bijvoorbeeld een
vaas, op het apparaat.
•Raak het netsnoer niet met
natte handen aan.
•Als de schakelaar op OFF
staat, is het apparaat niet
volledig losgekoppeld van de
netspanning (MAINS).
•De apparatuur wordt in de
buurt van het stopcontact
geïnstalleerd, zodat dit altijd
gemakkelijk toegankelijk is.
•Hantera nätkabeln varsamt.
Håll i kabeln när den kopplas
från el-uttaget.
•Utsätt inte apparaten för fukt,
vatten och damm.
•Koppla loss nätkabeln om
apparaten inte kommer att
användas i lång tid.
•Täpp inte till
ventilationsöppningarna.
•Se till att främmande föremål
inte tränger in i apparaten.
•Se till att inte insektsmedel
på spraybruk, bensen och
thinner kommer i kontakt med
apparatens hölje.
•Ta inte isär apparaten och
försök inte bygga om den.
•Ventilationen bör inte
förhindras genom att täcka
för ventilationsöppningarna
med föremål såsom tidningar,
bordsdukar eller gardiner.
•Placera inte öppen eld, t.ex.
tända ljus, på apparaten.
•Apparaten får inte utsättas för
vätska.
•Placera inte föremål fyllda
med vätska, t.ex. vaser, på
apparaten.
•Hantera inte nätsladden med
våta händer.
•Även om strömbrytaren står
i det avstängda läget OFF,
så är utrustningen inte helt
bortkopplad från det elektriska
nätet (MAINS).
•Utrustningen ska vara
installerad nära strömuttaget
så att strömförsörjningen är lätt
att tillgå.
III
•DECLARATION OF CONFORMITY
CAUTION:(English)
(English)
To completely disconnect this product from the mains, disconnect the plug from the wall socket
outlet.
The mains plug is used to completely interrupt the power supply to the unit and must be within
easy access by the user.
We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with
the following standards:
EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.
Following the provisions of Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC, the EC regulation
1275/2008 and its frame work Directive 2009/125/EC for Energy-related Products (ErP).
•ÜBEREINSTIMMUNGSERKLÄRUNG
(Deutsch)
VORSICHT:(Deutsch)
Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das sich diese Erklärung bezieht, den
folgenden Standards entspricht:
EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3.
Gemäß den Bestimmungen der Niederspannungsrichtlinie 2006/95/EG und EMV Richtlinie 2004/108/
EG, der Verordnung (EG) Nr. 1275/2008 der Kommission und deren Rahmenrichtlinie 2009/125/EG zu
energieverbrauchsrelevanten Produkten (ErP).
•DECLARATION DE CONFORMITE
Um dieses Gerät vollständig von der Stromversorgung abzutrennen, trennen Sie bitte den
Netzstecker von der Wandsteckdose ab.
Die Hauptstecker werden verwendet, um die Stromversorgung zum Gerät völlig zu unterbrechen; er
muss für den Benutzer gut und einfach zu erreichen sein.
(Français)
PRECAUTION:(Français)
Nous déclarons sous notre seule responsabilité que l’appareil, auquel se réfère cette déclaration, est conforme aux
standards suivants:
EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3.
Selon la directive 2006/95/EC concernant la basse tension et la directive CEM 2004/108/EC, la réglementation
européenne 1275/2008 et la directive 2009/125/EC établissant un cadre de travail applicable aux produits liés à
l’énergie (ErP).
•DICHIARAZIONE DI CONFORMITÀ
Pour déconnecter complètement ce produit du courant secteur, débranchez la prise de la prise
murale.
La prise secteur est utilisée pour couper complètement l’alimentation de l’appareil et l’utilisateur
doit pouvoir y accéder facilement.
(Italiano)
ATTENZIONE:(Italiano)
Dichiariamo con piena responsabilità che questo prodotto, al quale la nostra dichiarazione si riferisce, è conforme
alle seguenti normative:
EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3.
Facendo seguito alle disposizioni della direttiva sul basso voltaggio 2006/95/EC alla direttiva EMC 2004/108/EC, alla
norma EC 1275/2008 e alla relativa legge quadro 2009/125/EC in materia di prodotti alimentati ad energia (ErP).
QUESTO PRODOTTO E’ CONFORME
AL D.M. 28/08/95 N. 548
•DECLARACIÓN DE CONFORMIDAD
Per scollegare definitivamente questo prodotto dalla rete di alimentazione elettrica, togliere la spina
dalla relativa presa.
La spina di rete viene utilizzata per interrompere completamente l’alimentazione all’unità e deve
essere facilmente accessibile all’utente.
PRECAUCIÓN:(Español)
(Español)
Para desconectar completamente este producto de la alimentación eléctrica, desconecte el enchufe
del enchufe de la pared.
El enchufe de la alimentación se utiliza para interrumpir por completo el suministro de alimentación a
la unidad y debe de encontrarse en un lugar al que el usuario tenga fácil acceso.
Declaramos bajo nuestra exclusiva responsabilidad que este producto al que hace referencia esta declaración, está
conforme con los siguientes estándares:
EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3.
De acuerdo con la directiva sobre baja tensión 2006/95/CE y la directiva sobre CEM 2004/108/CE, la normativa CE
1275/2008 y su directiva marco 2009/125/EC para productos relacionados con la energía (ErP).
•EENVORMIGHEIDSVERKLARING
VOORZICHTIGHEID:(Nederlands)
(Nederlands)
Om de voeding van dit product volledig te onderbreken moet de stekker uit het stopcontact worden
getrokken.
De netstekker wordt gebruikt om de stroomtoevoer naar het toestel volledig te onderbreken en
moet voor de gebruiker gemakkelijk bereikbaar zijn.
Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt, waarop deze verklaring betrekking heeft, in
overeenstemming is met de volgende normen:
EN60065, EN55013, EN55020, EN61000-3-2 en EN61000-3-3.
Volgens de voorzieningen van lage spanningsrichtlijn 2006/95/EC en EMC-richtlijn 2004/108/EC, de EU-richtlijn
1275/2008 en de kaderrichtlijn 2009/125/EC voor energieverbruikende producten (ErP).
•ÖVERENSSTÄMMELSESINTYG
(Svenska)
FÖRSIKTIHETSMÅTT:(Svenska)
Härmed intygas helt på eget ansvar att denna produkt, vilken detta intyg avser, uppfyller följande standarder:
EN60065, EN55013, EN55020, EN61000-3-2 och EN61000-3-3.
Uppfyller reglerna i lågspänningsdirektivet 2006/95/EC och EMC-direktivet 2004/108/EC, EU-förordningen
1275/2008 och ramverksdirektivet 2009/125/EC för energirelaterade produkter (ErP).
Koppla loss stickproppen från eluttaget för att helt skilja produkten från nätet.
Stickproppen används för att helt bryta strömförsörjningen till apparaten, och den måste vara
lättillgänglig för användaren.
D&M Professional Europe
A division of D&M Europe B.V.
Beemdstraat 11
5653 MA Eindhoven
The Netherlands
IV
A NOTE ABOUT RECYCLING:
This product’s packaging materials are recyclable and can be reused. Please dispose of any
materials in accordance with the local recycling regulations.
When discarding the unit, comply with local rules or regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with the
local regulations concerning battery disposal.
This product and the supplied accessories, excluding the batteries, constitute the applicable
product according to the WEEE directive.
HINWEIS ZUM RECYCLING:
Das Verpackungsmaterial dieses Produktes ist zum Recyceln geeignet und kann wieder
verwendet werden. Bitte entsorgen Sie alle Materialien entsprechend der örtlichen RecyclingVorschriften.
Beachten Sie bei der Entsorgung des Gerätes die örtlichen Vorschriften und Bestimmungen.
Die Batterien dürfen nicht in den Hausmüll geworfen oder verbrannt werden; bitte entsorgen Sie
die Batterien gemäß der örtlichen Vorschriften.
Dieses Produkt und das im Lieferumfang enthaltene Zubehör (mit Ausnahme der Batterien!)
entsprechen der WEEE-Direktive.
UNE REMARQUE CONCERNANT LE RECYCLAGE:
Les matériaux d’emballage de ce produit sont recyclables et peuvent être réutilisés. Veuillez disposer
des matériaux conformément aux lois sur le recyclage en vigueur.
Lorsque vous mettez cet appareil au rebut, respectez les lois ou réglementations en vigueur.
Les piles ne doivent jamais être jetées ou incinérées, mais mises au rebut conformément aux lois en vigueur sur la
mise au rebut des piles.
Ce produit et les accessoires inclus, à l’exception des piles, sont des produits conformes à la directive DEEE.
NOTA RELATIVA AL RICICLAGGIO:
I materiali di imballaggio di questo prodotto sono riutilizzabili e riciclabili. Smaltire i materiali conformemente alle
normative locali sul riciclaggio.
Per lo smaltimento dell’unità, osservare le normative o le leggi locali in vigore.
Non gettare le batterie, né incenerirle, ma smaltirle conformemente alla normativa locale sui rifiuti chimici.
Questo prodotto e gli accessori inclusi nell’imballaggio sono applicabili alla direttiva RAEE, ad eccezione delle batterie.
ACERCA DEL RECICLAJE:
Los materiales de embalaje de este producto son reciclables y se pueden volver a utilizar. Disponga de estos
materiales siguiendo los reglamentos de reciclaje de su localidad.
Cuando se deshaga de la unidad, cumpla con las reglas o reglamentos locales.
Las pilas nunca deberán tirarse ni incinerarse. Deberá disponer de ellas siguiendo los reglamentos de su localidad
relacionados con los desperdicios químicos.
Este producto junto con los accesorios empaquetados es el producto aplicable a la directiva RAEE excepto pilas.
EEN AANTEKENING MET BETREKKING TOT DE RECYCLING:
Het inpakmateriaal van dit product is recycleerbaar en kan opnieuw gebruikt worden. Er wordt verzocht om zich van
elk afvalmateriaal te ontdoen volgens de plaatselijke voorschriften.
Volg voor het wegdoen van de speler de voorschriften voor de verwijdering van wit- en bruingoed op.
Batterijen mogen nooit worden weggegooid of verbrand, maar moeten volgens de plaatselijke voorschriften
betreffende chemisch afval worden verwijderd.
Op dit product en de meegeleverde accessoires, m.u.v. de batterijen is de richtlijn voor afgedankte elektrische en
elektronische apparaten (WEEE) van toepassing.
OBSERVERA ANGÅENDE ÅTERVINNING:
Produktens emballage är återvinningsbart och kan återanvändas. Kassera det enligt lokala återvinningsbestämmelser.
När du kasserar enheten ska du göra det i överensstämmelse med lokala regler och bestämmelser.
Batterier får absolut inte kastas i soporna eller brännas. Kassera dem enligt lokala bestämmelser för kemiskt avfall.
Denna apparat och de tillbehör som levereras med den uppfyller gällande WEEE-direktiv, med undantag av batterierna.
V
Getting started
Getting started
Contents
Connection··············································································11
Others························································································23
Memo function·············································································23
Memo settings············································································23
1
Specifications·········································································27
Index···························································································28
Index
Cables used for connection·························································11
Basic connections········································································11
Connecting the power cord························································12
Troubleshooting···································································26
Specifications
Preset menu map·········································································25
How to adjust the various Preset settings···································25
Troubleshooting
Turning the power on··································································13
Turning the power off··································································13
Playback························································································13
CD playback·················································································13
CD-ROM/CD-R/CD-RW playback·················································14
USB memory device or HDD playback········································15
Operations during playback························································17
Setting playback mode································································17
Playback·······················································································17
Pause···························································································17
Fast forward/Rewind···································································18
Setting the cue point···································································18
Adjusting the playback speed······················································19
Adjusting the playback speed without changing the pitch··········19
Changing the playback speed temporarily (pitch bend function)·19
Manual loop playback··································································19
Adjusting the track end time························································20
Adjusting brake time····································································21
Relay play····················································································22
Power on play··············································································22
Preset
Accessories·····················································································2
About this manual·········································································2
Main features··················································································3
Cautions on handling·····································································3
Discs································································································4
Discs playable on this unit·····························································4
Holding discs·················································································4
Loading discs·················································································4
Cautions on loading discs······························································4
Cautions on storing discs······························································4
Cleaning discs················································································4
Supported media and files····························································5
Supported media···········································································5
Playable files··················································································5
Part names and functions·····························································6
Front panel·····················································································6
Display···························································································9
Rear panel····················································································10
Others
Preset function······································································25
Playback
Playback····················································································13
Connection
Getting started········································································1
About this manual
This symbol indicates a reference page on
which related information is described.
This symbol indicates a supplementary
information and tips for operations.
NOTE
This symbol indicates points to remember
operations or function limitations.
nnIllustrations
Note that the illustrations in these instructions are for explanation
purposes and may differ from the actual unit.
Preset
or
European,U.K and Asia/
Pacific models
Specifications
r
Troubleshooting
U.S.A and
Canada models
Others
e
v
Playback
(Contents)
•Owner’s manual (This manual)
ePower cord (For use with this unit only) .................................. 1
rRCA cable................................................................................. 1
tRemote control connection cable............................................. 1
yWarranty (for North America model only)................................. 1
nnSymbols
Connection
qOwner’s Manual....................................................................... 1
wDN-D4500MK2 Resource CD-ROM......................................... 1
Getting started
Accessories
Check that the following parts are supplied with the product.
t
Index
2
Cautions on handling
3
Index
•About care
•Wipe the cabinet and control panel clean with a soft cloth.
•Follow the instructions when using a chemical cleaner.
•Benzene, paint thinner or other organic solvents as well as
insecticide may cause material changes and discoloration if brought
into contact with the unit, and should therefore not be used.
Specifications
•Moving the unit
•Please remove any discs from both trays of the drive unit before
transport.
•Turn off the power and unplug the power cord from the power
outlet. Next, disconnect the connection cables to other system
units before moving the unit.
Troubleshooting
•Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If that
occurs, move the mobile phone away from this unit when it is in use.
Preset
•About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
Others
•Proper ventilation
If the unit is left in a smoke-filled environment for long periods of
time. the surface of the optical pickup may get dirty, preventing it
from receiving signals properly.
Playback
NOTE
However that depending on the recording quality, the player may not
be able to play some finalized CD-R/RW discs.
•Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
•Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When going on vacation or leaving home
for long periods of time, be sure to unplug the power cord from the
power outlet.
Connection
6. Hot Start / Stutter
Playback can be started instantaneously from points A-1 and A-2.
In the stutter mode, these same buttons play momentary audio
while pressed and held down.
7.Brake
8. Relay Play
When this mode is set, CD1 and CD2 start their playback alternately.
This unit can relay the playback of CD1 and CD2 every track or
every disc.
9. Power on Play
The player can be set so that playback in the relay mode starts
when the power is turned on.
10.Fader Start
The DN-D4500MK2 FADER START controls are compatible with
various Denon DJ mixers and other mixers on the market.
11.Auto Disc Tray Close System
12.Preset functions - Different presets can be changed according
to your needs.
13.Custom Setting Memory
14.USB memory device Audio playback function
15.CD TEXT / MP3 ID3 Tag name display
16.CD-R / RW Playback
This player can play CD-R/RW discs, but only if they are finalized.
Getting started
Main features
The DN-D4500MK2 is a Dual Digital Media Player equipped with a
variety of functions and high performance characteristics, specifically
designed for Mobile and Club DJ’s around the world.
Control section
1. The DN-D4500MK2 can be easily mounted on a standard
19-inch rack.
2. Improved visibility under low lighting conditions thanks to a
large fluorescent display, back-lit illuminated action buttons
and illuminated disc trays.
3. Improved interface operation thanks to a large jog/Shuttle
wheel and track select knob.
Functions
1. Shockproof function protecting against external vibrations
2. Auto Level Search / Instant Start
3. Pitch / Pitch Bend & Key Adjust
4. MP3/USB Playback
It is possible to play MP3 files created in the specified format found
on page 14. Files can be searched for easily, by either manually
scanning, or by using a number of file search functions (File search,
File/Folder search, Artist name search, Title name search, File
name search).
5. Seamless Loop
Playback can be looped between any two points in a track without
any break in the audio. Two loop start points (A-1 and A-2) can be
set anywhere within the track or disc.
Discs playable on this unit
Holding discs
Cautions on storing discs
Discs marked with the logo at right can be
played in this unit.
Do not touch the signal surface.
wCD-R/CD-RW
Cleaning discs
Specifications
Cautions on loading discs
4
Gently wipe the disc from the
inside towards the outside.
Do not wipe in a circular
motion.
NOTE
Do not use record spray, antistatic agents, benzene, thinner or other
solvents.
Index
•Do not get fingerprints, oil or dirt on discs.
•Take special care not to scratch discs when removing them from
their cases.
•Do not bend or heat discs.
•Do not enlarge the hole in the center.
•Do not write on the labeled (printed) surface with ball-point pens,
pencils, etc., or stick new labels on discs.
•Water droplets may form on discs if they are moved suddenly from
a cold place (outdoors for example) to a warm place, but do not try to
dry them off using a hair-dryer, etc.
Troubleshooting
•If there are fingerprints or dirt on a disc, wipe them off before using
the disc. Fingerprints and dirt can impair sound quality and cause
interruptions in playback.
•Use a commercially available disc cleaning set or a soft cloth to clean
discs.
Preset
•Only load one disc at a time. Loading two or more discs can damage
the unit or scratch the discs.
•When the disc is drawn into the unit, be careful not to trap your
fingers.
•Do not insert anything other than discs into the disc loading slot.
•Do not use cracked or warped discs or discs that have been repaired
with adhesive, etc.
•Do not use discs on which the sticky part of cellophane tape or labels
is exposed or on which there are traces of where labels have been
removed. Such discs can get caught inside the player and damage it.
•If the label side of the disc is dirty, wipe it clean before use. If the
disc loading/ejection roller becomes dirty, discs may not load or eject
correctly.
Others
zzWhat is finalization?
Finalization is the process that makes recorded CD-R/CD-RW discs
playable on compatible players.
Loading discs
Playback
NOTE
•Discs in special shapes
(heartshaped discs, octagonal
discs, etc.) cannot be played. Do
not attempt to play them, as
doing so can damage the unit.
•Some discs and some recording formats cannot be played.
•Non-finalized discs cannot be played.
•Be sure to remove discs after using them.
•Be sure to store discs in their cases to protect them from dust,
scratches, warping, etc.
•Do not store discs in the following places:
•Places exposed to direct sunlight for long periods of time
•Dusty or humid places
•Places exposed to heat from heaters, etc.
Connection
qMusic CDs
Getting started
Discs
Getting started
Supported media and files
The following media and files can be played back on this unit.
Supported media
Connection
Disc
: CD, CD-R, CD-RW, CD-ROM
: CD-DA (CD-TEXT compatible),
CD-ROM (ISO9660/Joliet format/Romeo format)
Playback
Disc type
Format
Media type
Format
Others
USB memory device
: FLASH DRIVE, HDD
: FAT16/FAT32
Preset
NOTE
Troubleshooting
•When a multisession disc is used, the more sessions there are, the
more time will be required to read the disc.
•The maximum capacity of USB memory devices and HDDs you can
use is 2 TB.
•This unit cannot format USB memory devices or HDDs.
File type Extension
.mp3
AAC
.m4a
.mp4
.aac
WAV
.wav
AIFF
.aif
.aiff
ID-3 tag
Notes
Max.=74min
per one file
playable
Max.=74min
per one file
playable
Index
MP3
Format
Same as CD-ROM
(MPEG 1/ 2 / 2.5 Layer
3)
AAC-LC Encode
ADTS Format only
CBR: 32–320kbps/sec
44.1kHz stereo
VBR: 44.1kHz stereo
Linear PCM 44.1kHz
16bits stereo
Linear PCM 44.1kHz
16bits stereo
V1.0, V1.1, V2.2, V2.3,
V2.4
Specifications
Playable files
NOTE
DRM protected files cannot be played back.
5
Getting started
Part names and functions
Front panel
r
q y
t
t
w
e
Connection
e
r
Playback
Others
Preset
Troubleshooting
i
Q6 W0
W1
W1
W2
W3 Q3
W4
Q5 Q3
W6 Q9
i
Q6 W0
W1
W1
W2
W3 Q3
W4
Q5 Q3
Specifications
W6 Q9
Index
Q8
u
o
Q7 Q1
Q2
W5
Q0
Q4
Q8
u
6
o
Q7 Q1
Q2
W5
Q0
Q4
nnDN-D4500MK2 Front panel
qPOWER button (hON jOFF)
•Press this button to turn the power on.
•Be sure to close the disc holders before turning
off the power.
•This lights when the power is on.
eDisc holder
tDisc holder OPEN/CLOSE button
yUSB1 port
•Insert a USB memory device or connect a
HDD.
iContinue/Single button
( CONT./SINGLE, RELAY)
•CONT./SINGLE:
Short Pressing alternates the play ending
mode between CONT. (Continuous: play more
tracks) and SINGLE (stops playing at the end
of a track and re-cues back to your set point).
•SINGLE PLAY LOCK:
SINGLE PLAY LOCK can be selected by
PRESET(10). At this time , if this button is
pressed, it will be selected. When SINGLE
PLAY LOCK is selected, track selection during
playback is disabled. This prevents playback
from stopping when the Track Select Knob
is turned accidentally during playback. Play
ending mode is the same as single.
•RELAY:
When this button is pressed for more than
1 sec, you can turn on and off RELAY PLAY
mode.
Q1CUE button
•Pressing the CUE button during play provides
a return to the position at which play was
started. Alternately pressing the PLAY/PAUSE
button and the CUE button allows the CD to
be played from the same position any number
of times.
•The CUE button lit, when the standby mode
is set.
•In CUE mode, by pressing the CUE button
makes a Stutter sound from the CUE point. This
is called Stutter play for added performance.
(Stutter)
Q2PLAY/PAUSE button (13)
•Use this button to start playback.
•Press once to start playback, once again to set
the pause mode, and once more to resume
playback.
•When the Brake mode is ON, press the Play/
Pause to activate the Brake sound.
oBRAKE button
When this button is pressed you can turn the
Brake mode on and off.
When the Brake mode is on, the LED lights.
No LED indicates OFF mode.
7
Q5
PITCH/KEY, RANGE button
•With this button you can select PITCH and KEY
ADJUST mode. Mode changes Pitch on, Key
Adjust on and both off cyclically. Green LED
indicates in Pitch mode and Orange indicator
in Key Adjust mode. No LED indicates OFF
mode.
•RANGE:
Press this button for more than 1 sec to
select the pitch range. The pitch range can be
selected with the TRACK SELECT knob from
±4, 10, *16, 24, 50 or 100%. (*Max pitch for
MP3)
Q6
TIME, TOTAL button
•Press this to switch the time display between
the elapsed time or remaining time per track
or per disc.
•When this button is pressed for more 1
second, you can display the total time. (4 way,
audio, CD only)
Q7Display
•See page 9.
Index
•Press this button to open and close the disc
holder.
•The disc holder will not open during playback.
Stop playback before pressing this button.
•While the player is in pause, cue, or frame
repeat mode, turn this wheel to find the cue
point in frame measurement.
•In the Playback mode, turn this wheel to
temporarily pitch bend the playing speed.
•Use this to adjust the playing speed.
•The playing speed decreases when moved
upwards and increases when moved
downwards.
Specifications
•This flashes while the disc holder is opening
and closing.
•The LED lights when the disc holder is open
and serves as the disc holder illumination.
uJog wheel (inner wheel)
Q4Pitch slider
Troubleshooting
rDisc holder LED
•Note that there are many buttons working
two different functions selected by short time
pressing or long pressing (1 second or more). The
mark indicates short time press function and
mark indicates long time press function.
•The playing speed increases/decreases while
these buttons are held down.
•When either button is released, the playing
speed returns to the previous speed.
Preset
CAUTION
•Do not place foreign objects in the disc holders.
Doing so could damage the player.
•Do not press the disc tray in manually when the
power is off, as this may result in malfunction
and damage to the player.
CAUTION
Q3PITCH BEND +/– button
Others
•Place discs in this holder.
•Press the disc holder OPEN/CLOSE button to
open and close the disc holder.
knob
(SEL./ MP3 DISC SEARCH MODE)
•TRACK:
Turn this knob to select the first or next track
to be played.
Turn the knob clockwise by one click to move
one track forward, counterclockwise by one
click to move one track backward.
When the knob is turned while pressing it
down, one click corresponds to advancing 10
tracks at a time.
In the Preset and Memo mode, use this knob
to set and enter Preset and Memo settings.
•MP3 DISC SEARCH MODE:MP3 DISC only.
When pressing this knob down for more than
1 second, the MP3 file search selection mode
is selected.
Playback
wPOWER indicator
Q0TRACK SELECT/MP3 DISC SEARCH MODE
Connection
NOTE
nnRC-D45MK2 Front panel
Getting started
Part names and functions
Q8Shuttle ring (outer ring)
W1A1, A2 buttons
W2B button
W3EXIT/RELOOP button
•When this button is pressed during a seamless
loop, the track resumes back to normal play
from the B point. (EXIT)
When pressed again, the playback jumps back
into your A-B seamless loop. (RELOOP)
NOTE
Memo’s can not be set for MP3 files.
W6SOURCE select buttons
(CD/USB1/USB2)
•When “CD” is selected, the CD LED lights.
•When “USB1” is selected, the USB1 Green
LED lights.
•When “USB2” is selected, the USB2 Red LED
lights.
Index
•Press this button to set the end point for loop
playback (point B).
BACK, PRESET button
•BACK
Pressing this button during the folder search
displays the folder one level up.
•PRESET:
When this button is pressed for more than 1
sec, the PRESET mode starts.
Specifications
•Press these buttons to set the start point for
loop playback (point A-1 or A-2).
•Press these buttons to use the stutter and hot
start functions.
W5
Troubleshooting
•Press this button to switch between the loop
mode/hot start mode and stutter mode.
•After setting the B point, the B TRIM MODE
can be selected.
Preset
W0FLIP/B TRIM button
Others
•Press this button to open and close the disc
holder.
•The disc holder will not open during playback.
Stop playback before pressing this button.
TITLE/ MEMO button
•CD TEXT:
When there is CD text data, the CD text data
is displayed automatically or when the button
is pressed.
If no TEXT is available, the display will indicate
“No TEXT”.
•MP3:
When an MP3 file has ID-3 tag data, the title,
artist name and album name can be selected
and displayed each time the button is pressed.
•MEMO:
The memo mode starts when this button is
pressed once in the CUE mode.
Playback
Q9Disc holder OPEN/CLOSE button
W4
Connection
•This control is used to select the scanning
direction and speed.
The CD is scanned in the forward direction
when the shuttle ring is turned clockwise from
the center position. To scan backwards, the
shuttle ring is turned counterclockwise.
•The scanning speed increases as the wheel is
turned further.
Getting started
Part names and functions
8
Display
rMP3 file search mode indicator
ENGLISH
(5) Display
DN-D4500 Rear panel
Analog output jacks 1, 2
ANALOG OUT 1, 2)
i
u
q
e
t
r
Digital output jacks 1, 2
DIGITAL OUT 1, 2)
Digital data is available from this jack.
Use 75 Ω/ohms pin cord for connection.
We recommend you use braided wire type
shielded cable.
NOTE: The playback level after analog
conversion is set to –6dB bellow the
usual level to avoid digital distortion.
Fader input jacks 1, 2 (FADER 1, 2)
o
tCharacter display
•This displays various operational information,
text message, etc.
FILE:
FILE indicator appears in display, when in
the FILE name search mode.
FOLDER:
FOLDER indicator appears in display, when
in the FILE & FOLDER name search mode.
TITLE:
TITLE indicator appears in display, when in
the TITLE name search mode.
ARTIST:
ARTIST indicator appears in display, when in
the ARTIST name search mode.
yPlay mode indicators
indicators
w Loop mode
qTrack, minute, second
and frame
displays
eTime mode indicators
• DN-D4500 has Loop mode indicators consist of
Connect the supplied 8pin din cable to the
RC-D45 control unit.
•These displays
information.
two sets of A (A1,
A2), B and position
two arrows. A
indicate
current
and B marks indicate A and B points are set.
• Two arrows indicate loop setting mode as
follows.
wLoop mode indicators
Example: A1 B
A1
B
A1
B
A1
B
A1
B
A1
B
uMEMO indicator
•MEMO sign appears in display when there
is a memory setting for the currently playing
track or the track at which the standby mode
is currently set.
Q0MP3 indicators
•Lights when an MP3 disc is detected.
Index
Both arrows
on:
•DN-D4500MK2 has Loop
mode
indicators
Seamless Loop mode
consist of two sets of A, (A1, A2),
B and
two
Both arrows
flashing:
Seamless
Loop Playing
arrows. A and B marks
indicate
A and B points
RC-D45 Rear panel
Left arrow on, right flashing:
,
are set.
Exit play from Seamless Loop
Control connector
•Two arrows indicate
loop setting mode as
Connect the opposite side of supplied 8pin din
e Time mode indicators
cable to the DN-D4500 (main
unit).
• When the TIME/TOTAL button is pushed, the
follows.
Time mode indicator switches as follows:
Example: A1 B
ELAPSED:
Track’s elapsed time is displayed.
Both arrows
on:
REMAIN:
Track’s remaining time is displayed.
Seamless Loop mode
T. + ELAPSED:
,
arrows
The, Both
total elapsed
timeflashing:
of disc or
programmed track is displayed.
Seamless Loop Playing
T. + REMAIN:
The , total
disc or
,
Leftremaining
arrowtimeon,of right
programmed track is displayed.
flashing:
Exit play from Seamless Loop
•When the TIME/TOTAL button is pressed,
the Time mode indicator switches as follows:
ELAPSED:
Track’s elapsed time is displayed.
t Character display
REMAIN:
• This
displays various operational information,
text message, etc.
Track’s remaining time is displayed.
indicators
y Play
T.mode
+ ELAPSED:
• When SINGLE indicator lights up, playback will
finish
at endtotal
of current
track.
The
elapsed
time of disc or
• When CONT. indicator lights up, playback
programmed
is displayed.
continues
to the end of thetrack
disc.
T.
+
REMAIN:
u MEMO indicator
• MEMO
signtotal
appearsremaining
in display when there
is aof disc or
The
time
memory setting for the currently playing track
programmed
displayed.
or the
track at which thetrack
standbyismode
is
•This numeric indicator display the playback
speed (pitch).
Specifications
CAUTION:
To completely disconnect this product from
the mains, disconnect the plug from the wall
socket outlet.
The mains plug is used to completely interrupt
the power supply to the unit and must be
within easy access by the user.
•When SINGLE indicator lights up, playback will
finish at end of current track.
•When CONT. indicator lights up, playback
continues to the end of the disc.
oPitch display
Troubleshooting
Remote control connector
REMOTE)
• These displays indicate current position
information.
y
r MP3 file search mode indicator
Preset
Use this when your mixer has Fader Start
function with 3.5 mm stereo mini cord.
q Track, minute, second and frame
displays
Others
w
•Play position indicator:
The 30 white dots indicate where is playing
visually in a track in the normal play.
•End of Message:
When the time remaining to the end of the
track is less than the specified time, the EOM
(End Of Message) play position indicator
flashes along with the remaining time, a
notification to the user that the track will end
soon.
zz The EOM time can be set within the preset
mode.
Playback
!0
These are unbalanced output jacks. The audio
signals from the both players are output from
these jacks.
iPlay Position indicators
Connection
FILE:
FILE indicator appears in display, when in
the FILE name search mode.
FOLDER:
FOLDER indicator appears in display, when
in the FILE & FOLDER name search mode.
TITLE:
TITLE indicator appears in display, when in
the TITLE name search mode.
ARTIST:
ARTIST indicator appears in display, when in
the ARTIST name search mode.
Getting started
Part names and functions
currently set.
9
9
Rear panel
nnDN-D4500MK2 Rear panel
qAnalog output jacks 1, 2
w
w
wDigital output jacks 1, 2
t
eFader input jacks 1, 2 (FADER 1, 2)
•Use this when your mixer has Fader Start
function with 3.5 mm stereo mini cord.
rRemote control connector
u
uControl connector
•Connect the opposite side of supplied 8 pin din
cable to the DN-D4500MK2 (main unit).
Specifications
(REMOTE)
•Connect the supplied 8pin din cable to the
RC-D45MK2 control unit.
nnRC-D45MK2 Rear panel
Troubleshooting
The playback level after analog conversion is set
to –6dB bellow the usual level to avoid digital
distortion.
yAC inlet (AC IN)
Preset
NOTE
•Insert a USB memory device or connect a
HDD.
Others
r
tUSB2 port
Playback
e q e q
(DIGITAL OUT 1, 2)
•Digital data is available from this jack.
•Use 75 Ω/ohms pin cord for connection.
•We recommend you use braided wire type
shielded cable.
To completely disconnect this product from the
mains, disconnect the plug from the wall socket
outlet.
The mains plug is used to completely interrupt the
power supply to the unit and must be within easy
access by the user.
Connection
(ANALOG OUT 1, 2)
•These are unbalanced output jacks. The audio
signals from the both players are output from
these jacks.
y
Getting started
Part names and functions
CAUTION
Index
10
b
n
Pitch/Brake .......................................................11
⁄2
Specifications ...................................................16
Check that the following parts are included in addition to the main unit:
Basic connections
q Operating instructions ........................................1
r Remote control connection cable.......................1
w Connection cords for signal output (RCA) ..........2
t Service Station List .............................................1
e Remote
control
(RC-D45)
............................1
Select
theunit
cables
according
to the equipment being connected.
•This is an example of the basic connections when connecting this unit to a DJ mixer.
L
1 MAIN FEATURES
R
RCA
cable
RCA Cord
CH3
input
jackjack
CH3
input
CH4
jack
CH4input
input
jack
RCA
cable
RCA Cord
L
R
Index
11
Specifications
DN-D4500MK2
7
Troubleshooting
Max. 10°
Preset
The DN-D4500MK2 will work normally when the player unit is mounted
within 10 degrees off the vertical plane at the front panel. If the unit
is tilted excessively, the disc may not be loaded or unloaded properly.
right with right).
•Connect the cables to the correct input and output terminals.
•Insert the plugs securely. Loose connections will result in the
generation of noise.
•Do not bundle power cords together with connection cables. Doing
so can result in humming or noise.
•DN-D4500MK2 is not compatible with RC-D45 (old model) and
DN-D4500 (old model) is not compatible with RC-D45MK2. Do not
connect incompatible units.
Others
CH3Fader
Fader jack
CH4
CH3
jack
CH4Fader
Faderjack
jack
3.5 mm stereo
Hot Start / Stutter
3.5 mm stereo
3.5 mm stereo
Playback can be started instantaneously from
mini
cable
minimm
cordstereo
3.5
mini cord
points A-1 and A-2.
mini cable
In the stutter mode, these same buttons play
DN-X900
momentary audio while pressed and held down.
DN-X900
Control section
17.
Brake
1. The DN-D4500 can be easily
mounted
on
a
Coaxial cable (sold separately)
18. Relay Play
standard 19-inch rack.
When this mode is set, CD1 and CD2 starts
2. Improved visibility under low lighting
nn For FADER jack
playback alternately.
conditions thanks to a large fluorescent display,
This unit can relay the playback of CD1 and CD2
back-lit illuminated action buttons and
every track or every disc.
illuminated disc trays.
DN-D4500
DN-D4500
MK2
Stereo
mini cable
(sold separately)
19. Power on Play
3. Improved interface operation
thanks
to a large
The player can be set so that playback in the relay
CD2
jog/Shuttle wheel and track select knob.
CD1
CD2
mode starts when the power is turned on.
Fader
jack
nn For REMOTE jack
CD1
Fader jack
Functions
Fader jack
10.
Fader
Start
CD
DRIVE
SIDE
CONTROLLER
SIDE
Fader
jack
1. Shockproof function protecting against external
The DN-D4500 FADER START controls are
(DN-D4500MK2)
(RC-D45MK2)
vibrations
compatible with our DN-X400, DN-X500,
2. Auto Level Search / Instant Start
DN-X800, DN-X900 or DN-X1500 mixers.
CD1Output
Output jack
CD2
jack
CD1
jack
CD2Output
Output
jack
3. Pitch / Pitch Bend & Key Adjust
11. Auto Disc Tray Close System
4. MP3 Playback
12. Preset functions - Different presets can be
It is possible to play MP3 files created in the
changed according to your needs.
specified format found
on
page
13.
Remote control connection cable
(supplied)
13. Custom
Setting Memory
NOTE
Files can be searched for easily either manually, or
14. CD TEXT / MP3 ID3 Tag name display
NOTE:
•USB
hubs cannot be used.
by scanning or using a number of file search
15. CD-R / RW Playback
• Use a commercially available 3.5mm stereo mini cord for the Fader jack connections.
•In order to prevent playback output clipping due to differences in playback level when an effector is used, set the playback level to –6 dB from
functionsNOTE
(File search, File/Folder search, Artist
This player can play CD-R/RW discs, but only if
name search,
Title
name
search,
File
name
search).
the
normal
playback
level
after converting digital output to analog.
•Do not plug in the power cord until all connections
have been
they are finalized.
5. Seamless Loop
•DENON does
not guarantee that all USB memory devices will operate or receive power. When using a portable USB connection type HDD of
Note: However that depending
on the
completed.
Playback can be looped between any two points in
recording quality,
player
may
be an AC adapter can be connected to supply power, use the AC adapter.
kind
tonot
which
•When making connections, also refer to the operating instructions
of thethe
a track without any break in the audio. Two loop
able to play some finalized CD-R/RW
the
other
components.
start points (A-1 and A-2) can be set anywhere
discs.
sureortodisc.
connect the left and right channels properly (left with left,
within •Be
the track
The DN-D4500 is a double CD/MP3 RCA
playercable
equipped
16.
(supplied)
with a variety of functions and high performance
characteristics, specifically designed for Mobile and
nn For DIGITAL OUT terminals
Club DJ’s around the world.
Playback
nn For LINE OUT terminals
DN-D4500
Connection
Cables used for connection
Max. 10°
Getting started
Connection
2 ACCESSORIES
CAUTION:
• Be sure to use the supplied control cord. Using
another type of cable may result in damage.
• Be sure the power is off when connecting the
control cord. Otherwise the units may not work
properly.
• Never connect any remote controllers other than
the RC-D45.
Doing so can damage the equipment.
Getting started
Connecting the power cord
Connect the supplied power cord to this unit, and insert the plug into
the wall socket.
Connection
NOTE
Playback
•Do not plug in the power cord until all connections have been
completed.
•Insert the plug fully and securely into the socket. Incomplete
connection to the power supply may cause damage to the unit, or
noise.
Others
Preset
To AC outlet
(AC 120 V, 60 Hz)
Troubleshooting
Power cord
(supplied)
U.S.A and Canada models
Specifications
To AC outlet
(AC 230 V, 50/60 Hz)
Index
European,U.K and Asia/
Pacific models
To prevent the power plug from falling out, we recommend fixing the
power cord to the AC cord holder. Use a Phillips screwdriver to fix the
power cord to the AC cord holder.
12
OPEN/CLOSE
Turning the power on
Disc holder
Press POWER ON/OFF.
“DENON DN-D4500 MK2” appears on the display, and the power switches on.
The power switches off.
POWER ON/OFF
SEL.
OPEN/CLOSE
NOTE
SEL.
Be sure to close the disc holders before turning off the power.
CD playback
•Press and turn SEL. to select 10 tracks at a time.
13 lights green, and playback starts.
If you select a track during playing, playback starts from the beginning of the selected track.
13
Index
CUE
BACK
PLAY/PAUSE
Specifications
CUE
BACK SOURCE
PLAY/PAUSE
1 Press SOURCE to switch the source to CD.
2 Press OPEN/CLOSE on the unit to open the disc holder and insert the disc.
3 Turn SEL. to select the track you want to play.
4 Press 13.
Troubleshooting
Playback
SOURCE
Preset
OPEN/CLOSE
Others
Press POWER ON/OFF.
Playback
Turning the power off
Connection
Disc holder
Getting started
Playback
CD-ROM/CD-R/CD-RW playback
For details on the files that can be played on this unit, see vpage 5.
Press OPEN/CLOSE on the unit to open the disc holder.
The CD is ejected from the disc loading slot.
NOTE
13 lights green, and playback starts.
nnSelecting the file
There are three methods for selecting files.
File search mode
To search a file directly from among all of those recorded in a disc.
Folder search mode
To specify the layer to select a folder or file from among all of those
recorded in a disc.
To sort the files in alphabetical order to select from among all of
those recorded in a disc.
nnSelecting files in file search mode
The cue standby mode is set at the start of the selected file.
nnSelecting files in file name search mode
1 Hold down SEL. (-MP3 DISC SEARCH MODE).
2 Turn SEL. to select “File Name”.
3 Press SEL.
4 Turn SEL. to select a file.
5 Press SEL.
To change to the next initial letter, hold down SEL. and turn.
The cue standby mode is set at the start of the selected file.
1 Hold down SEL. (-MP3 DISC SEARCH MODE).
2 Turn SEL. to select “FileSearch”.
3 Press SEL.
4 Turn SEL. to select a file.
•To select files in group of ten, hold down SEL. and turn.
The cue standby mode is set at the start of the selected file.
14
See the illustration on the previous page for details of the buttons used for the
operations on this page.
Index
The cue standby mode is set at the start of the selected tracks.
The CD is ejected from the disc loading slot.
Specifications
File name search mode
•Press BACK to return to the previous folder.
Hold down OPEN/CLOSE for the disc holder 1 or 2, and
press POWER ON/OFF.
•To return to the layer of the upper folder, press BACK.
Troubleshooting
7 Turn SEL. to select the track you want to play.
8 Press SEL.
9 Press 13.
The folder names or track names within the folder are shown
in the display.
If the CD is not ejected due to a malfunction in the unit even when
OPEN/CLOSE is pressed, it can be ejected using other buttons.
Preset
nnIf the CD cannot be ejected
Others
1 Press SOURCE to switch the source to CD.
Press OPEN/CLOSE on the unit to open the disc
2 holder
and insert the disc.
3 Hold down SEL. (-MP3 DISC SEARCH MODE).
4 Turn SEL. to select “FileFolder”.
SEL. to select the folder that contains the track
5 Turn
you want to play.
6 Press SEL.
1 Hold down SEL. (-MP3 DISC SEARCH MODE).
2 Turn SEL. to select “FileFolder”.
3 Press SEL.
4 Turn SEL. to select a file.
5 Press SEL.
Playback
Be sure the CD is paused before ejecting. If OPEN/CLOSE is pressed
during CD playback, the CD will not be ejected.
nnSelecting files in folder search mode
Connection
NOTE
This section explains the operating procedures for CD-ROM/CD-R/
CD-RW discs that have been finalized as data CDs. For CDs that have
been finalized as music CDs, see “CD playback” (vpage 13).
nnEjecting CDs
Getting started
Preparation for playback
USB memory device or HDD playback
SEL.
The cue standby mode is set at the start of the selected tracks.
BACK SOURCE
(CD/USB1/USB2)
BACK
NOTE
•Depending on the type of mass-storage USB memory device or portable music player, it may take some
time for this unit to recognize the device.
•Do not connect devices or cables that do not conform to USB standards.
•USB memory devices will not work via a USB hub.
•NTFS format USB memory devices and HDDs are not supported. If used, this unit may malfunction.
•When using a HDD that has an automatic power ON/OFF function that switches the HDD power on and
off in sync with the computer, disable this function in the settings.
•The maximum capacity of USB memory devices and HDDs you can use is 2 TB.
•This unit cannot format USB memory devices or HDDs.
15
Index
SOURCE
(CD/USB1/USB2)
•FAT16/FAT32 is supported for the USB memory device and HDD.
•When using a USB HDD of the kind to which an AC adapter can be connected to supply power, use the
AC adapter.
•If the USB memory device is not recognized, disconnect the USB memory device and then reconnect it.
Specifications
5 Turn SEL. to select the track you want to play.
6 Press SEL.
SEL.
Troubleshooting
The folder names or track names within the selected folder are shown in the display.
•Press BACK to go back 1 folder level.
Preset
4 Press SEL.
Others
The LED indicator lights in green when USB1 port is selected.
The LED indicator lights in red when USB2 port is selected.
Playback
1 Connect a USB memory device or HDD to the USB1 port or USB2 port.
2 Press SOURCE to switch the source to USB1/USB2.
3 Turn SEL. to select the folder.
Connection
•Connect USB memory device or HDD to the USB port on the top panel, and prepare to playback a track.
•For details on the file formats that can be played on this unit, see vpage 5.
Getting started
Preparation for playback
Getting started
Preparation for playback
nnRemoving the USB memory device or HDD
Connection
Before removing the USB memory device or HDD, be sure to make sure the access lamp
for the connected device is turned off.
NOTE
Playback
•Be sure the USB memory device or HDD is paused before removing.
•When removing USB memory device or HDD, use the above procedure to turn off the USB DRIVE
indicator before removing. Incorrectly removing the USB memory device or HDD may damage the data
stored on the device.
•DENON cannot accept any responsibility whatsoever for the damage or loss of data from USB memory
devices or HDDs that are used in conjunction with this device.
•There is no guarantee that this unit is compatible with all types of USB memory devices or HDDs.
Others
Preset
Troubleshooting
Specifications
Index
16
See the illustration on the previous page for details of the buttons used for the
operations on this page.
SEL.
CONT./
SIGNAL
-RELAY
Setting playback mode
This sets how tracks are played back.
SEL.
Press SINGLE/CONT.
CONT.
Shuttle ring
CUE PLAY/PAUSE
Jog wheel
SINGLE
CUE PLAY/PAUSE
CONT.
Shuttle ring
The SINGLE indicator lights in the display, and “Lock Off” is shown. In this mode, when
playback of the track is completed, the track returns to the cue point and is paused.
The CONT. indicator in the display lights. In this mode, when playback of the track has
finished, the next track is played back.
Press 13.
Pause
13 flashes, and the track is paused.
•Press 13 again to resume playback from the point at which the track was paused.
17
Index
Press 13 during playback.
Specifications
13 lights green, and playback starts.
Troubleshooting
Playback
Preset
Jog wheel
Others
The SINGLE indicator lights in the display, and “Play Lock” is shown. In this mode, when
SINGLE
(PLAY LOCK) playback of the track is completed, the track returns to the cue point and is paused.
Playback
•The playback mode is switched in the following order each time the button is pressed.
SINGLE (PLAY LOCK)
SINGLE
Connection
CONT./
SIGNAL
-RELAY
Getting started
Operations during playback
Setting the cue point
There are four methods for fast forward/rewinding.
By setting a cue point, the track can be played back from the set position.
nnFast forward/Rewind using shuttle ring and jog wheel
nnSetting the cue point
During playback, turn the shuffle ring.
Pause the track in the position where you want to set the cue point, and press CUE.
(2) Starting playback from the Middle of a track (Manual Search)
6 PITCH/BRAKE
Connection
Fast forward/Rewind
Getting started
Operations during playback
Playback
• When the track is selected with the TRACK SELECT knob o and the PLAY/PAUSE button !1 is pushed,
• There are two ways to change the playing speed.
If turned in the FWD direction, the playback point is moved to the forward direction, and playback is
The cue
point isposition,
set at the
position.
playback starts from the beginning of that track. If you wish to start from
a different
use paused
the
• Adjust the Pitch using the pitch slider !3.
resumed from the new point.
procedure described below to search for the desired position.
• The
PITCH
BEND
button
!2 or
jog wheel
can
be used
to temporarily change the pitc
•Irrespective
of
the
mode,
the
cue
point
is set
at the
start
of the
track
wheny
the
track
is loaded.
If turned in the RVS direction, the playback point is moved to the reverse direction, and playback is
• The playing speed can be changed greatly to achieve effect similar to those achievable w
resumed from the new point.
• If you wish to preserve the original key of sound, set the Key Adjust function to ON.
Shockproof memory
Find the play start position.
• A maximum of approximately 20 seconds
Turn
the
shuttle
ring
!7
to
change
the
During playback, turn the jog wheel (inner side).
uncompressed audio data is stored into memory
(1) Pitch
playback position quickly. (Search for the
If turned in the FWD direction, the playback speed increases.
•Playback
stops, returns
(per drive). This guards
audible interruptions
due to the position where you want to playback again (cue point), and is paused
approximate playback position.)
If turned in the RVS direction, the playback speed decreases.
to external mechanical
shocks
as bumps
(back
cue such
function).
[Pitch slider]
[PITCH BEND button]
The fast forward/reverse mode
or other hard vibrations.
Set always
the variable
speed mode.
Push the PITCH BEND + (or
•When this function is used, playback can
be started
from the same position.
is set when the shuttle ring
• If advanced data reading is not possible due to
Push the PITCH button !4 to light
PITCH BEND –) button !2.
(outer side) !7 is turned.
scratches or dirt During
on the disc,
playback stops
• The Pitch increases or
playback,
press CUE. 1-1 the PITCH LED.
The speed changes according to
once the data stored
up to that
pointcues
is read.
decreases temporarily wh
→ KEY
adjust)
→ OFF
• PITCH
Playback
stops,
to the playback start
position
(cue(key
point),
and
pauses.
the angle at which the ring is
RVS FWD
FWD
(Green) (Orange)
(Off) (LED color)
PITCH BEND + or PITCH
1 RVS
turned.
2-1 – button !2 is pushed.
• When operated during playback, playback
During pause, turn the shuffle ring.
• The extent to which the PI
Pitch
after
operation.
The Pitch decreases
If turned in the FWD direction, the pause point is resumes
moved to
thethe
forward
direction, and pause mode is set
decreases
!2 changes the Pitch is pr
There are two methods for moving the cue point,
using the shuttle ring, or using the jog wheel.
• When playback is started, the jog wheel is
when
the
pitch
slider
!3
(2) Starting playback from the Middle ofamount
a track
Se
of (Manual
time the butto
at the new point.
set to the bend mode.
is moved upwards,
longer the button is held
If turned in the RVS direction, the pause point is moved to the reverse direction, and pause mode is set
1
-2
• When the track
is selected
knob o and the PLAY
• When turned fully in either direction, the
increases
whenwith
the the
pitchTRACK SELECT
the percentage of change
at the new point.
playback starts
from!3the
beginning of that track. If you wish to start from
playback position jumps about 10 seconds.
slider
is moved
Pitch
described
below
to searchdirection
for the desired
position.
During pause, turn the shuttle ringprocedure
in
the forward
or reverse
toSetmove
the
The jump time can be selected in the preset
downwards.
the jog
wheel to the p
During pause, turn the jog wheel (inner side).
increases
mode from 10, 20, 30 or 60 sec.
cue
point
while
listening
to
the
playback
sound.
During
playback,
pitch bend
If turned in the FWD direction, the pause point is moved to the forward direction frame by frame, and
memory
thepitch
playranges,
start position.
DN-D4500Find
has six
JogShockproof
wheel.
pause mode is set at the new point.
• Aplaying
maximum
app
Turn the jog wheel y. (Search for the precise
Turn the
shuttle
4%, 10%, *16%,
24%,
50%ring
and!7 to change the
• The
speed of
increas
If turned in the RVS direction, the pause pointplayback
is moved
to the reverse direction frame by frame, and
uncompressed
audio
d
position.)
playback
position
quickly. (Search for the
(*Max
MP3)
When
the
100%.
gradually
when
the
jog
wh
If the jog wheel is turned in the forward
or reverse
direction,
you can move the
cue
pause mode is set at the new point.
(per
drive).
This guards
approximate
playback
position.)
RANGE
button
!4
is
pushed
y
is
turned
clockwise
and
When the jog wheel (inner side)
point while listening to the playback
sound
by frame.
to external
mechanica
for more than
1 sec,frame
the The
pitch
gradually
when
2-2 decreases
fast forward/reverse mode
y is turned, the frame move
or other hard vibration
range can be selected byisturning
set when the shuttle ring wheel y is turned
mode is set.
1-3 the TRACK SELECT knob o.
•
If
advanced
data
read
counterclockwise. When
(outer side) !7 is turned.
The playback position can be
scratches
or dirt
on
the
jog
wheel
y,
the
play
The speed changes according to
• When the TRACK SELECT
2 RVS FWD moved in units of one frame.
once the data stored u
thethe
angle at which the ring is to the previous speed.
knob o RVS
is pushed
down
FWD
FWD
1 RVS
Listen to the sound and find the desired play
• When playback is stoppe
pitch
range is entered turned.
and
start position.
wheel is set to the search
the pitch• range
Whenselection
operated during playback, playback
Press
CUE
.
mode
is
completed.
resumes
after
the
operation.
NOTE:
The cue point is set at the moved position. • When playback is started, the jog wheel is
• For MP3 discs, frames are not displayed,
however frame resolution is audible by turning
(2) BRAKE set to the bend mode.
Press 13.
• When turned fully in either direction, the
the jog wheel (inner side) y.
The cue point is set at the moved
position,
andplayback
playback
starts.
position
10 seconds.
• Use
this function
to
achieve
effectjumps
similarabout
to analog
players.
The jump time can be selected in the preset
mode from 10, 20, 30 or 60 sec.
Push the BRAKE button i to light
the BRAKE LED.
Turn the jog wheel y. (Search for the precise
• The effect
soundposition.)
is similar to
playback
a DJ turntable coming to a
quick stop. This effectWhen
can the jog wheel (inner side)
1
ythe
is turned, the frame move
be achieved by pushing
PLAY/PAUSE button !1mode is set.
The playback position can be
during playback.
moved in units of one frame.
RVS FWD
I
I
§
I
Preset
SEARCH
Others
nnReturning to the cue point
SCAN
6 7
Troubleshooting
nnMoving the cue point
Specifications
Setting with shuttle ring and jog wheel
0%
1
I
I
SEARCH
I
SCAN
6 7
3
18
I
I
I
SEARCH
§
I
I
2
SCAN
6 7
§
§
I
Index
SEARCH
2
SCAN
6 7
See the illustration on the previous page for details of the buttons used for the
Listen to the sound and find the desired play
operations on this page.
start position.
NOTE:
Changing the playback speed temporarily (pitch bend function)
PITCH BEND -/+
PITCH BEND -/+
PITCH/KEY
PITCH/KEY
Pitch slider
Pitch slider
RANGE
RANGE
FILP/BTRIM EXIT/RELOOP
FILP/BTRIM EXIT/RELOOP
nnUsing the PITCH BEND buttons
A1,A2,B
A1,A2,B
Connection
This function temporarily changes the playback speed.
There are 2 methods for changing the playback speed.
Getting started
Operations during playback
Press PITCH BEND +/–.
Playback
(2) Starting playback from the Middle of a track (Manual Sear
PITCH BEND + Playback speed is increased while the button is being pressed.
• When the track is selected with the TRACK SELECT knob o and the PLAY/PA
to start from a
Find the play start position.
nnDuring playback, turn the jog wheel
If turned in the FWD direction,
If turned in the RVS direction, playback speed is decreased.
The fast forward/reverse mode
is set when the shuttle ring
(outer side) !7 is turned.
The speed changes according to
the angle at which the ring is
FWD
FWD
turned.
I
I
I
SEARCH
§
Shuttle ring
Adjusting the playback speed
RVS
1 RVS
Use the pitch slider to adjust the playback speed (pitch).
Manual loop playback
4%
10 %
16 %
100 %
50 %
24%
Turn the jog wheel y. (Search for the precise
playback position.)
The A indicator lights in the display, and playback
starts from the set A point.
16 %
When the jog wheel (inner side)
y is turned, the frame move
is set.
Press B at the position where you want to endmode
playback.
The playback
position
can A
beand B.
The B indicator lights in the display, and manual loop playback
repeats
between
moved in units of one frame.
RVS FWD
2
2 Press PITCH/KEY - RANGE.
3 Move the pitch slider, and adjust to the desired playback speed.
The LED lights green.
I
I
SEARCH
I
10 %
§
GFor MP3 DISCH
4%
playback or pause, press A1 at the position where you want to start
1 During
playback.
SCAN
6 7
2
Listen to the sound and find the desired play
start position.
NOTE:
• For MP3 discs, frames are not displayed,
A2 and B2 points can be set in the same way.
however frame resolution is audible by turning
the jog wheel (inner side) y.
Adjusting the playback speed without changing the pitch
When the playback speed is adjusted, the pitch is not changed.
Press PITCH/KEY - RANGE.
The LED lights orange.
19
Index
• When operated during playback, playback
resumes after the operation.
• When playback is started, the jog wheel is
set to the bend mode.
Set the starting point (A point) and end point (B•point),
playback
repeated
seamlessly
between the
Whenand
turned
fully iniseither
direction,
the
two points.
playback position jumps about 10 seconds.
Two loop ranges (A1 and B1 points, A2 and B2 points)
can time
be set.
The jump
can be selected in the preset
mode from 10, 20, 30 or 60 sec.
Range **% is displayed.
Each time SEL. is turned, the range in which the playback speed can be adjusted switches as
shown below. Turn SEL. to select the pitch range, and press SEL. to select the playback speed.
Specifications
1 Press and hold PITCH/KEY - RANGE.
SCAN
6 7
Troubleshooting
CUE PLAY/PAUSE
Jog wheel CUE PLAY/PAUSE
BRAKE
BRAKE
Shuttle ring
Jog wheel
Shockproof memory
• A maximum of approx
uncompressed audio data
(per drive). This guards au
to external mechanical s
or other hard vibrations.
• If advanced data reading
scratches or dirt on the
once the data stored up t
Preset
Turn the shuttle ring !7 to change the
playback position quickly. (Search for the
playback
speed is increased.
approximate playback position.)
Others
playback starts from the beginning of that track. If you wish
while the button is being pressed.
PITCH BEND – Playback speed is decreasedprocedure
described below to search for the desired position.
nnAdjusting loop points
In normal playback or pause, press EXIT/RELOOP.
• When the track is selected with the TRACK SELECT knob o and the PLAY
playback starts from the beginning of that track. If you wish to start from
procedure described below to search for the desired position.
1 During manual loop playback, press A1.
the jog wheel while listening to the playback sound, and move to the position
2 Turn
where you want to end playback.
nn If the current playback position is before the A-B positions,
nn If the current playback position is after the A-B positions,
I
I
§
I
SCAN
6 7
•It can be adjusted in 1 frame units.
nnExiting auto loop playback
Auto loop playback exits, and normal playback resumes.
nnStutter
zzAdjustment range for B point
Stutter effect can be used at A1 and A2 points set as a loop start point.
B point (end point) adjustment is complete.
I
I
I
SEARCH
§
, and the player enters the stutter mode.
RVS
FWD
When the jog wheel (inner side)
y is turned, the frame move
mode is set.
The playback position can be
moved in units of one frame.
Listen to the sound and find the desired play
start position.
NOTE:
While pressing the FLIP press the A1 or A2 to clear
the corresponding A and B points.
A2 point can be stuttered in the same way.
• For MP3 discs, frames are not displayed,
however
frame
is audible
by at
turning
Press FLIP/B TRIM for more than 1 sec to clear
both
A1resolution
and A2
points
once.
the jog wheel (inner side) y.
nnChanging the end point of manual loop playback
Adjusting the track end time
During manual loop playback or pause, press B at the position where you want to end
playback.
nnBrake
•The B point (end point) is moved to the position where B was pressed.
1 Press BRAKE.
2 Press PLAY/PAUSE during playback.
nnExiting manual loop playback
The BRAKE LED lights.
During manual loop playback, press EXIT/RELOOP.
“Exit Loop” is shown in the display, and normal playback resumes.
The ending time of the track is delayed, and the characteristic like an analog player is obtained.
nnReturning to manual loop playback
In normal playback, press EXIT/RELOOP.
The playback position moves to the A point (start point) and manual loop playback starts.
20
See the illustration on the previous page for details of the buttons used for the
operations on this page.
Index
2 way.
B2 point for A2 point can be adjusted in the same
SCAN
6 7
Specifications
3
1 Press FLIP repeatedly until “STR A1” is shown in the display.
2 Hold down A1 to stutter A1 point.
to the loop play mode, press FLIP repeatedly until “H/S A1” is shown in
nnClear the A1/A2 point
3 Tothe return
display.
Turn the jog wheel y. (Search for the precise
playback position.)
Press B at the position where you want
to end playback.
Troubleshooting
During auto loop playback, press EXIT/RELOOP.
Preset
• When operated during playback, playback
resumes after the operation.
GAdjustable rangeH
• When playback is started, the jog wheel is
It can be adjusted from 1 frame after the A point (start
to themode.
end of the track.
set point)
to the bend
• When turned
fully in either direction, the
z
playback position jumps about 10 seconds.
B can be selected in the preset
The jump time
A
of60
thesec.
track
mode from 10, 20,End
30 or
+3 f
Others
RVS
1 RVS
If the EXIT/RELOOP is pressed before the playback point passes the A point (start point), “Exit Loop” is
shown in the display, and normal playback resumes.
changes to
The fast forward/reverse mode
is set when the shuttle ring
(outer side) !7 is turned.
The speed changes according to
the angle at which the ring is
FWD
FWD
turned.
SEARCH
Playback
•Moves the playback point to the A point (start point) and manual loop playback starts.
Shockproof memory
• A maximum of app
uncompressed audio d
(per drive). This guards
to external mechanica
or other hard vibration
• If advanced data read
scratches or dirt on
once the data stored u
Connection
Find the play start position.
Turn the shuttle ring !7 to change the
playback position quickly. (Search for the
approximate playback position.)
•“Exit Off” is shown in the display.
•When the playback position passes the A point (start point) manual loop playback starts automatically.
Getting started
(2) Starting playback from the Middle of a track (Manual Se
Operations during playback
CONT./
SINGLE
RELAY
SEL.
Step 2
Step 4
Step 3
3 Press •BACK –PRESET to enter.
PLAY/PAUSE
Troubleshooting
The larger the step number is, the longer the brake time is.
Preset
BACK
PRESET
Step 1
Others
PLAY/PAUSE
CUE
1 Hold down •BACK –PRESET.
2 Press SEL. repeatedly to select the brake time.
Playback
BACK
PRESET
The brake time can be adjust using Preset function.
SEL.
Connection
CUE
Adjusting brake time
CONT./
SINGLE
RELAY
Getting started
Operations during playback
Specifications
Index
21
Power on play
What is relay play?
Playback relays between deck 1 and deck 2.
This mode enables playback to start automatically from the first track of the loaded CD when powering on.
A disc loaded in the next deck will be played after playback of the current track when
the playback modes of deck 1 and deck 2 are set to SINGLE, or after playback of all
tracks in the current disc when those modes are set to CONT.
“Now Saving” is shown.
Playback automatically starts from the first track when powering on.
Power on play can be set on CD drives 1 and 2, respectively.
Performing relay playback
Specifications
CONT./SINGLE on the first deck to select the playback mode, SINGLE or
1 Press
CONT., then hold down CONT./SINGLE to select the relay mode.
Troubleshooting
•If both a CD (track) and USB memory device (file) are loaded in each deck, relay playback between the
CD and the USB memory device is possible.
Preset
Files in the folder of the next deck will be played after playback of the current file when
the playback modes of deck 1 and deck 2 are set to SINGLE, or after playback of all files
in the current folder when those modes are set to CONT.
Others
nnUSB playback
Playback
1 Load a CD into the deck.
2 Hold down –PRESET.
3 Turn SEL. to select “Power Play”.
4 Press SEL. to display “P.PlayON”.
5 Press –PRESET.
nnCD playback
Connection
Relay play
Getting started
Operations during playback
The SINGLE or CONT. indicator flashes in the display. Turn SEL. to select a track or file.
Index
Press CONT./SINGLE on the second deck to select the playback mode, SINGLE or
2 CONT
.
The SINGLE or CONT. indicator flashes in the display. Turn SEL. to select a track or file.
3 Press PLAY/PAUSE of the first deck.
4 To stop the relay playback, press CUE on the deck currently played.
Relay playback starts.
*If not stopped, relay playback is repeated.
22
See the illustration on the previous page for details of the buttons used for the
operations on this page.
Getting started
Others
Memo settings
Details set in advance can be stored as memo data on a USB memory device or HDD or Flash Memory.
When you need to configure settings in a short space of time, settings can be configured automatically
SEL.
TITLE
MEMO
nnMemo Set
SEL.
Save the setting details to memo data.
“Complete!” is shown in the display.
BACK
PRESET
23
Index
•Cue point
•Manual loop point (A1/B1, A2, B2 point)
•Hot start or Stutter
•Playback speed
•Pitch ON or OFF
•Key adjust ON or OFF
•Pitch range
Specifications
•When “MEMO” is shown in the display, memo data has already been saved. Clear the saved memo
data, and redo the setting.
•If memo data cannot be saved, check the remaining capacity of the USB memory device or HDD. It may
not be possible to save memo data if there is not enough spare memory.
•If the USB memory device or HDD is equipped with a security function, check that the security is disabled.
•1000 is the maximum possible number of tracks that can be stored to memory.
However, to simplify the MEMO operations, the memory system manages each 200 MEMO data groups
as a minimum unit (the total 1000 memory capacity divided into 5 memory data groups). When you want
to clear just one MEMO data in the 1 MEMO CLEAR mode (vpage 24), the unit will erase the memo
information but not the internal memo allocation number. Accordingly, depending on conditions, the
number of tracks that can be stored in the memory may be fewer than 1000.
Once you reached 1000 stored points, you will see a message that says “MEMO FULL!”. At this time
you will need to “delete” old data to make room for new memo points. Therefore the oldest 200 memo
points in that group will be deleted and become available.
•The MEMO indicator on the display lights up when a track for which data is stored in the memory is
selected.
Details that can be saved as memo data
Troubleshooting
BACK
PRESET
Preset
“Memo Set?” is shown in the display.
Others
1 Set this unit with memo data.
2 Press TITLE - MEMO.
3 Press SEL.
Playback
TITLE
MEMO
Connection
Memo function
1 Select the track that is stored with the memo data that you want to clear.
•When a track that has memo data stored is selected, the MEMO indicator lights in the display.
•When a track that has memo data stored is selected, the MEMO indicator lights in the display.
2 Press TITLE - MEMO.
3 Press SEL.
2 Press TITLE - MEMO.
3 Turn SEL. to select “Memo Clr?”.
4 Press SEL.
5 Press SEL.
“Memo Call?” is shown in the display.
“Memo Call?” is shown in the display.
“Clear OK” is shown in the display.
Preset
The MEMO indicator in the display goes out, and the memo data is cleared.
Troubleshooting
When the playback speed is called from the memo data, the PITCH indicator flashes, and the pitch may
be locked.
This is because the actual playback speed and playback speed selected by the pitch slider differ. In order
to cancel the pitch lock, adjust the pitch slider to the same pitch as the called memo data.
nnDisc tray auto close
nnEnd of message
Index
During playback, the Play Position indicators start flashing when the remaining playing time to the end
of the track (set in the preset mode) is reached, indicating that the end of the track is near. (Preset item
6)
Specifications
Disc tray will automatically close after 30 seconds have elapsed for the disc tray auto close mode.
(Preset item 3)
24
Others
1 Select the track that is stored with the memo data that you want to call.
This function clears saved memo data.
Playback
nnMemo Clear
This function calls saved memo data.
Connection
nnMemo Call
Getting started
Memo function
Getting started
Preset function
Setting items
Auto Cue
P. Range
Fader Mode
Play Mode
Time Mode
Bpm Disp
Relay Mode
Relay Time
Index
Pitch
Preset Int
Specifications
Power Play
Version No
Troubleshooting
EOM Time
NOTE: This PRESET item can be only performed in CD1 (left side) of the remote
controller.
Clear all MEMO data in the non-volatile memory.
qTo clear all MEMO data, press the SEL. down.
“Clear OK?” flashes on the character display.
wPress the TRACK SEL. down again and select “OK” to execute clearing all MEMO
data.
“Memo Clear” is displayed on the character display while clearing.
eOnce clearing is completed, “Complete!” is displayed.
The DN-D4500MK2’s software version is displayed.
(SYSTEM/DSP/SER/RC)
Set all the preset data back to the factory defaults.
qTo clear the PRESET data, press the TRACK SEL. down.
“Initial OK?” flashes on the character display.
wPress the SEL. down. again and select “OK” to start clear the preset data.
“Preset Int” is displayed on the character display while data clearing.
eOnce clearing is completed,
“Complete!” is displayed.
Preset
Jump Time
Description
Memo Clear (MEMO ALL CLEAR)
Others
Auto Close
Setting items
MemoClear
Playback
Brake Time
Description
Sets the detection level of the sound start point when ignoring the soundless part at
the head of a track at playback.
(A.CUE ON* / A.CUE OFF)
Setting the track end time
(STEP 1 / STEP 2* / STEP 3 / STEP 4)
Time for automatically closing disc holder.
(Close OFF / Close 10s / Close 30s* / Close1min)
Select the jump time of QuickJump.
(Jump10sec* / Jump20sec / Jump30sec / Jump1min)
Select the playing pitch range when the power is turned on.
(4% Range / 10% Range* / 16% Range / 24% Range)
Sets the notification for the time remaining until the end of the track being played back.
(EOM OFF / EOM 10 sec* / EOM 15 sec / EOM 20 sec / EOM 30sec / EOM 60 sec /
EOM 90 sec)
Switches the operation for fader start for the mixer connected to this unit.
Select 1-line (TS) type cable (Play and Pause).
Select 2-line (TRS) type cable (CUE and Play)
(Play / CUE* / Play Pause)
Switches power on playback on or off.
Playback starts when the power is turned on if a disc is loaded.
(P. Play ON / P. Play OFF*)
Select the pitch mode when the power is turned on.
(Pitch ON* / Key. AdjON (KEY ADJUST ON) / Pitch OFF)
Select the play mode when the power is turned on.
(Single / Cont. / Play Lock*)
Select the time mode when the power is turned on.
(Elapsed* / Remain)
Select the BPM display
(Disp ON* / Disp OFF)
Switches relay playback on or off.
(Relay ON / Relay OFF*)
Select the crossover time the currently playing track when the opposite drive start to
play with the Relay Play function.
(Relay Osec* / Relay 1sec / Relay 2sec / Relay 3sec)
Connection
Preset menu map
The “*” mark next to the data indicates the default value.
How to adjust the various Preset settings
1 Hold down •BACK –PRESET.
2 Turn SEL. to select the setting item.
3 Press •BACK –PRESET.
“PresetMode” is displayed.
Press SEL. to enter the selected item.
“Now Saving” is displayed.
Configuration is complete.
25
Symptom
Symptom
•Some USB memory devices cannot be operated by the power supplied
from this unit. The unit supplies 5 V/1 A to a USB memory device. Use
a USB memory device that is compatible with the specifications of this
unit.
•Check if the USB memory device is firmly connected to the USB port.
This unit does not operate
properly, or there is no
sound.
•Check the connections for all devices.
•Check the file sampling frequency. Only files with a sampling frequency
of 44.1 kHz can be played on this unit.
There is no sound.
Or the sound is distorted.
•Check the mixer connections.
•The mixer adjustments or switching may be unsuitable. Adjust the knobs
on the mixer.
There is no sound.
Or the sound is too quiet.
•Check the connections for all devices.
•Switch the input source switching button to the device that is currently
playing.
“Fail” is displayed.
•If the USB memory device or HDD is equipped with a security function,
check that the security is disabled.
•Memo data cannot be saved on a USB memory device or HDD formatted
in HFS+ format. Use FAT16 or FAT32 format.
A CD-R or CD-RW disc
cannot be played.
•The disc has not been finalized.
Finalize the disc then play it.
•The recording conditions and/or the quality of the disc itself are poor.
Use a properly recorded disc.
Index
•Check that the plug is inserted correctly into the wall socket, and that the
power cord is inserted into this unit.
Specifications
Power does not turn on.
Troubleshooting
•The disc may be dirty or scratched. Either clean the dirt from the disc, or
replace with another disc.
Preset
“Disc Error” is displayed.
Others
The USB memory device is
not recognized.
Cause/Solution
•Check that the power is on.
•Discs cannot be ejected during playback. Stop playback before ejecting
the disc.
Playback
•Has the unit initialized the USB memory device with applicable formats?
(FAT 16/FAT 32)
•Are you using a USB hub? If so, directly connect the USB memory device
to a USB port on the front panel of the unit.
•Are you using a USB extension cable? If so, directly connect the USB
memory device to the USB port on the front panel of the unit.
•Are the USB memory device contents applicable to this unit? Use the
“Files” menu to confirm whether the contents are applicable to the unit.
•When a USB memory device of 192 MB or less is formatted with FAT
32, this unit may not be able to read it. If that is the case, format it with
FAT 16.
•This unit does not support a USB memory device containing encrypted
data.
If this unit does not operate properly, check the items listed in the table below.
If the symptom is not covered on the check list, contact your dealer or service centers.
Service centers are listed at http://www.d-mpro.com or http://www.denondj.com.
Cannot eject disc holder.
Cause/Solution
Data stored in a USB
memory device cannot be
displayed (read).
Connection
If a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in this owner’s manual?
3. Is the external device (DJ mixer, player or effects processor) operating correctly?
Getting started
Troubleshooting
26
nn General
nn Functions
NOTE
Troubleshooting
24-bit (internal DSP Process)
Specifications
44.1 kHz at normal pitch
8 times
0.01% or less
90 dB or more
85 dB or more
20 to 20,000 Hz
Index
Main out, Monitor out
Quantization:
Sampling frequency:
Oversampling rate:
Total harmonic distortion:
Signal to noise ratio:
Channel separation:
Frequency response:
Analog output
Output level:
Load impedance:
Digital output
Signal format:
Output level:
Service centers are listed at http://www.d-mpro.com or http://www.denondj.com.
Settings
nn Audio section
zzSpecifications and design are subject to change without notice for purpose of improvement.
Others
Finalized CD-R or CD-RW discs can be played back in this unit.
However, according to recording quality, some CD-R/RW discs cannot
be played.
Installation:
19-inch rack mountable
Player unit: 2U
Remote control unit: 2U
Power supply:
U.S.A., Canada and Taiwan R.O.C. models: 120 V AC ±10%, 60 Hz
European models: 230 V AC ±10%, 50/60 Hz
Power consumption:
25 W
Environmental conditions: Operational temperature: 5 to 35°C (41 to 95°F)
Operational humidity: 25 to 85% (no condensation)
Storage temperature: –20 to 60°C (-4 to 140°F)
Playback
Within 20 msec.
±4% (0.1% pitch), ±10% (0.1% pitch), ±16% (0.1% pitch)
±24% (1.0% pitch), ±50% (1.0% pitch), ±100% (1.0% pitch)
Pitch bend:
Pitch range ±4% – ±24% : ±32%
Pitch range ±50%, ±100% : ±99%
Search precision:
1/75 sec. (1 subcode frame)
Max. scan speed:
Over 20 times normal speed
Max. MEMO memory steps: 1000 steps
Instant start:
Variable pitch:
Compact disc player
Standard compact disc (12 cm disc), CD-TEXT
CD-R, CD-RW discs
Connection
Type:
Disc type:
Getting started
Specifications
2.0 V r.m.s.
10 kΩ or more
IEC958-Type2
0.5 Vp-p 75 Ω
27
vvA
vvF
Fader Mode························································· 25
Fast forward/Rewind··········································· 18
Finalization····························································· 4
Front panel···························································· 6
vvT
vvM
Time Mode·························································· 25
Manual loop playback·········································· 19
Memo Call··························································· 24
MemoClear··················································· 24, 25
Memo function···················································· 23
Memo Set··························································· 23
vvV
Version No··························································· 25
vvP
Pause·································································· 17
Pitch···································································· 25
Pitch bend function············································· 19
Playback······························································ 17
CD····································································· 13
CD-R································································· 14
CD-ROM··························································· 14
CD-RW······························································ 14
USB memory device········································· 15
Playback mode···················································· 17
Playback speed··················································· 19
Play Mode··························································· 25
Power on/off······················································· 13
Power on play····················································· 22
Power Play·························································· 25
P. Range······························································ 25
Preset Int····························································· 25
Preset settings···················································· 25
Index
vvE
EOM Time··························································· 25
Loop point··························································· 20
Specifications
Display··································································· 9
Stutter································································· 20
Troubleshooting
vvD
vvS
vvL
Preset
Cable
Coaxial cable····················································· 11
RCA cable························································· 11
Remote control connection cable····················· 11
Stereo mini cable·············································· 11
Connection
HDD·································································· 15
Power cord······················································· 12
USB memory device··································· 15, 16
Cue point····························································· 18
vvJ
Jump Time·························································· 25
Others
vvC
vvR
Rear panel··························································· 10
Relay Mode························································· 25
Relay play···························································· 22
Relay Time·························································· 25
Playback
vvB
Bpm Disp···························································· 25
Brake··································································· 20
Brake Time·························································· 25
vvH
Hot Start································································ 3
Connection
Accessories··························································· 2
Auto Close··························································· 25
Auto Cue····························································· 25
Auto loop playback·············································· 20
Getting started
Index
28
Getting started
nnDimensions
5/64
(2.0)
Connection
Playback
9/16 2-9/32 25/32
(14.2) (58.0) (20.0)
Unit: in. (mm)
18-31/32 (482.0)
Troubleshooting
15/64
(6.0)
3-15/32
(88.0)
Preset
3 (76.2)
Others
18-5/16 (465.0)
3 (76.2)
5/64 (2.1)
3-15/32
(88.0)
11/64
(4.2)
5/64 (2.0)
10-5/16
(261.0)
Index
9-51/64 (248.8)
Specifications
18-5/16 (465.0)
18-31/32 (482.0)
Weight: (Player unit:11 lbs (5.0 kg), Remote control unit: 4 lbs 2 oz (1.9 kg))
29
V00
3520 10166 00AP