Whirlpool Compactors Use & care guide

COMPACTORS
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service, call: 1-800-253-1301
or visit our website at
www.whirlpool.com
In Canada, for assistance, installation or service,
call: 1-800-807-6777 or visit our website at
www.whirlpool.ca
Table of Contents ................................................. 2
9872208C
TABLE OF CONTENTS
COMPACTOR SAFETY ..................................................................2
INSTALLATION INSTRUCTIONS ..................................................3
Unpacking ....................................................................................3
Location Requirements................................................................3
Electrical Requirements ...............................................................4
Freestanding and Undercounter Installation ...............................4
Changing the Decorative Panel ...................................................6
COMPACTOR USE.........................................................................7
How Your Compactor Works.......................................................7
Loading.........................................................................................7
Starting the Compactor ...............................................................8
Removing a Filled Bag .................................................................8
Installing a New Bag.....................................................................9
COMPACTOR CARE ......................................................................9
Cleaning........................................................................................9
TROUBLESHOOTING ..................................................................10
ASSISTANCE OR SERVICE .........................................................11
In the U.S.A. ...............................................................................11
In Canada ...................................................................................11
Accessories ................................................................................11
WARRANTY ..................................................................................12
COMPACTOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
DANGER
WARNING
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using an electrical appliance, basic precautions should always be followed, including the following:
■
Read all instructions before using the compactor.
■
Close supervision is necessary when used by or near
children. Do not allow to be used as a toy, or to run
unattended at any time. Lock Key Switch when not in use
and store key out of reach of children.
Do not touch moving parts.
Do not operate with a damaged cord set, plug, motor, or
after damage in any manner. Have the compactor
examined, repaired or adjusted by an authorized
serviceperson.
Use only for intended use as described in this manual. Do
not use other than manufacturer's recommended
attachments.
■
■
■
■
■
■
■
Do not compact toxic or volatile flammable material such as
oily rags and insect sprays. Do not compact lighted
cigarettes, cigars, or other hot or burning items. Do not
overload the compactor.
Do not take apart the compactor. Incorrect reassembly can
cause electric shock when subsequently used.
Handle a loaded trash bag with care. Sharp objects can
pierce the bag and cause injury. Do not overload trash bag
with heavy material such as glass.
This compactor is intended for household use only.
SAVE THESE INSTRUCTIONS
2
INSTALLATION INSTRUCTIONS
Installer: Leave Use and Care Guide with the homeowner.
Homeowner: Keep Use and Care Guide for future reference and
for local electrical inspector’s use, if required.
13. Remove the shipping base from the bottom of the compactor.
Unpacking
A
WARNING
B
Excessive Weight Hazard
Use two or more people to move and install compactor.
Failure to do so can result in back or other injury.
A. Leveling legs
B. Shipping base
IMPORTANT:
■ Do not grasp console to move compactor.
■
Begin in the room where the compactor will be located.
Location Requirements
Product Dimensions
1. Remove compactor from shipping carton.
2. Remove all packaging materials such as tape and shipping
pads.
3. Use a mild detergent and warm water to remove waxy
residue caused by shipping material.
4. Dry thoroughly with a soft cloth. For more information, see
“Cleaning.”
5. Be sure the power cord is attached to the cord clip on the
rear of the compactor.
34¹⁄₈"
(86.7 cm)
A
15"
(38.1 cm)
24"
(61 cm)
Cutout Dimensions
A. Cord clip
6. Place the 2 corner posts from the carton on the floor near the
compactor.
7. Open the compactor drawer and remove any shipping
materials or other items from the drawer.
NOTE: Do not remove the compactor bag.
8. Grasp the handle and raise the front of drawer until it clears
the drawer stops.
9. Grasp sides of drawer and lift drawer out of compactor.
10. Place the drawer on the 2 corner posts.
3" min.
(7.6 cm)
A
34¹⁄₄" min.
(87 cm)
24" min.
(61 cm)
11. Place the other 2 corner posts on the floor to the side of the
compactor.
12. Grasp the sides of the compactor cabinet and put compactor
on its side on top of the corner posts.
18" min.
(45.7 cm)
15¹⁄₄" min.
(38.7 cm)
A. Grounded electrical outlet must be a minimum of 3" (7.6 cm) away
from surrounding cabinets or nearby walls as shown. It can be
placed either to the left or the right side of the product.
3
Clearance Dimensions
Freestanding and Undercounter
Installation
NOTE: Proper installation is your responsibility. Make sure you
have everything necessary for correct installation. It is the
personal responsibility and obligation of the customer to contact
a qualified installer to assure that electrical installation meets all
national and local codes and ordinances.
Tools Needed
Gather the required tools and parts before starting installation.
B
A
A. Leave 6" (15.2 cm) of clearance space to the right side of the
compactor in order to remove the compactor bags.
B. Leave 23" (58.4 cm) of clearance in front of the compactor in
order to fully open or remove the compactor drawer.
■
Level
■
Pliers
■
Phillips No. 2 screwdriver
■
⁵⁄₁₆" hex-head wrench
■
Tape measure
■
Scissors
■
Flat-blade screwdriver
■
Utility knife
IMPORTANT:
■ Do not grasp control panel to move compactor.
■
Slide compactor onto cardboard or hardboard before moving
compactor across floor to avoid floor covering damage.
■
Do not allow the rear frame of the compactor to touch the
floor covering when lifting or moving compactor.
Freestanding Installation
Electrical Requirements
WARNING
1. Use pliers to lower leveling legs away from cabinet.
2. With the drawer still removed from the compactor cabinet,
place level inside on the floor of the cabinet. Check that the
compactor is level from front to back and side to side.
3. Adjust the leveling legs until the compactor is level.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Recommended Grounding Method
This compactor is for use on a single phase, 115-volt, 60 Hz, AC
only, 15- or 20-amp fused and properly grounded circuit and is
equipped with a grounding plug as shown below. It is recommended
that a separate circuit serving only this appliance be provided.
This compactor must be grounded while in use to reduce the risk
of electric shock. The compactor is equipped with a 3-conductor
cord and 3 prong grounding-type plug to fit the proper
grounding-type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire.
NOTE: Do not connect the green (or green and yellow) wire to a
live terminal.
4
4.
5.
6.
7.
Move the compactor close to its final location.
Plug into a grounded 3 prong outlet.
Slowly move compactor into its final position.
Check that compactor is still level. Repeat Step 1 if
necessary.
8. Grasp sides of compactor drawer and place bottom of
drawer into tracks.
9. Lift at the handle so drawer will go over drawer stops.
10. Close drawer.
11. Check to see whether drawer opens freely. If the toe plate
rubs against floor, see “Adjusting the Toe Plate” for further
instructions.
■
Undercounter Installation
If the compactor is to be midway between “1” and “3,”
place the retaining bracket mounting screws through “2.”
NOTE: Installation hardware is not provided. See “Accessories”
for ordering conversion kit.
1. Measure the height of your kitchen cabinet opening. The top
of the compactor should be at least ¹₈" (3 mm) from the top
of the kitchen cabinet opening.
The rear wheels are preset for a kitchen cabinet opening
height of 34¹⁄₄" (87 cm) (position 1).
A
B
3 2
1
To adjust for other kitchen cabinet opening heights:
■
Loosen self-tapping screw enough to clear stud from hole
in position 1.
■
Move the rear wheel and stud to position 2 or 3 as
needed for your kitchen cabinet opening measurement:
■
Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)
Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)
NOTE: To level the unit in position 3, you may need to
add shims under the front leveling legs.
Tighten screw.
■
Repeat for other rear wheel.
A. Countertop
B. Retaining bracket (provided in conversion kit)
9. Slowly lift the front slightly and roll compactor into the kitchen
cabinet opening.
10. Using 2 - #8 - 18 x ¹₂" mounting screws (provided in
conversion kit), fasten the retaining brackets (provided in
conversion kit) to the countertop with the mounting screws.
Countertop Mounting
B
A
1
2
3
C
A
C
D
A. Wheel bracket assembly
B. Compactor cabinet
B
C. Locating stud
D. Self-tapping screw (pivot)
2. Use pliers to lower leveling legs away from compactor
cabinet.
3. Adjust legs so there will be a ¹⁄₈" (3 mm) to ¹₄" (6.4 mm) space
between the top of the compactor and the top of the kitchen
cabinet opening.
4. Stand the compactor upright.
5. Remove the plastic plugs from the compactor cabinet top.
6. Move the compactor close to its final location.
7. Plug into a grounded 3 prong outlet.
8. Determine whether you want the compactor cabinet or
drawer front flush with the kitchen cabinet face.
Using 2 - #8 - 18 x ⁵₁₆" mounting screws (provided in
conversion kit), attach the retaining brackets (provided in
conversion kit) to the compactor cabinet top as needed. See
“Accessories.”
NOTE: Installation hardware is not provided with full cabinet
models. See “Accessories” for ordering conversion kit.
■
If the compactor cabinet face is to be flush with the
kitchen cabinet face, place retaining bracket mounting
screws through “1.”
■
If the compactor drawer front is to be flush with the
kitchen cabinet face, place retaining bracket mounting
screws through “3.”
A. Countertop
B. Retaining bracket (provided in conversion kit)
C. Mounting screw (provided in conversion kit)
NOTE: If retaining brackets cannot be attached to the underside
of countertop, attach mounting clips (provided in conversion kit)
to retaining brackets. Fasten compactor to kitchen cabinet face
with mounting screws through the mounting clips.
Cabinet-face Mounting
A
C
B
D
A. Mounting clip (provided
in conversion kit)
B. Kitchen cabinet
C. Retaining bracket (provided in
conversion kit)
D. Mounting screw (provided in
conversion kit)
11. Grasp sides of compactor drawer and place bottom of
drawer into tracks.
12. Lift at the handle so drawer will go over drawer stops.
13. Close drawer.
5
14. Check to see whether drawer opens freely. If the toe plate
rubs against floor, see “Adjusting the Toe Plate” for further
instructions.
Adjusting the Toe Plate
If the toe plate rubs the floor covering, the toe plate clearance
may be changed as follows:
1. Mark on each side of the toe plate the amount of toe plate
that rubs the floor covering.
2. Remove the drawer from the unit. See Step 3 in the
“Unpacking” section.
3. Use a ruler and a pencil or chalk to draw a line between the
marks on each side of toe plate.
4. Use scissors or utility knife to cut toe plate along line.
5. Replace drawer. If toe plate still rubs floor covering, repeat
steps 1 to 4.
2. Remove mounting screws attaching the toe guard to the
compactor. Remove toe guard.
3. Remove the mounting screws attaching the decorative panel
to the compactor. Remove decorative panel and discard
mounting screws.
4. Align the bottom of the custom panel with the bottom of the
drawer front.
5. Secure the panel from the back using four #8 x 1" wood
screws as shown.
6. Reinstall the toe guard using the existing screws and ¹⁄₂"
(13 mm) washer. Then, reinstall the foot pedal.
A
C
B
Changing the Decorative Panel
Trimless Panel with Handle
C
Dimensions
Use these dimensions drawings to create a custom panel for use
without a trim kit. The panel should be ¹⁄₂" to ⁵⁄₈" (13 mm to
16 mm) thick.
NOTE: A thicker panel may need rounded front corners and a
cutout for access to the handle.
D
E
F
23¹³⁄₁₆"
(60.5 cm)
A. Handle
B. Custom panel
C. Panel screw locations
D. Toe guard
E. Washer
F. Toe guard screw
Trimless Panel without Handle
Dimensions
Use these dimension drawings to create a custom panel for use
without a trim kit. The panel should be ¹⁄₂" (13 mm) minimum
thick.
15"
(38.1 cm)
Installation
1. Remove the mounting screws attaching the foot pedal to the
compactor. Remove foot pedal.
A
25"
(63.5 cm)
A
B
A. Mounting screws
B. Foot pedal
6
15"
(38.1 cm)
Installation
1. Remove the mounting screws attaching the foot pedal to the
compactor. Remove foot pedal.
7. Reinstall the toe guard using the existing screws and ¹⁄₂"
(13 mm) washer. Then, reinstall the foot pedal.
B
A
A
C
A
B
C
A. Mounting screws
B. Foot pedal
2. Remove mounting screws attaching the toe guard to the
compactor. Remove toe guard.
3. Remove the mounting screws attaching the decorative panel
to the compactor. Remove decorative panel and discard
mounting screws.
4. Align the bottom of the custom panel with the bottom of the
drawer front.
5. Secure the panel from the back using four #8 x 1" wood
screws as shown.
6. Attach a 15" (38,1 cm) x ¹⁄₂" (13 mm) quarter-round filler along
the top of the drawer front using glue or screws.
D
E
F
A. Custom panel
B. 15" x ¹⁄₂ " (38.1 cm x
13 mm) quarter-round
C. Panel screw
locations
D. Toe guard
E. Washer
F. Toe guard
screw
COMPACTOR USE
How Your Compactor Works
The compacting ram is the part of the compactor which
compresses the trash. The compacting ram does not go to the
bottom of the drawer. You will not see compacting of trash the
first few times you load the compactor.
NOTE: The compactor drawer should be more than ¹⁄₂ full before
the compactor can begin to compress the load.
You may hear a noise when glass breaks. Strong glass bottles
may not break at all. The trash in a full compactor bag will be
about ¹⁄₄ the size of its original bulk.
Loading
IMPORTANT: Do not push items down into compactor with
hands or feet.
NOTE: You will not see compacting of trash the first few times
you load the compactor. The compactor drawer should be about
¹⁄₂ full before the compactor can begin to compress the load.
1. Open the drawer. Lift and pull the handle or press the foot
pedal to open the drawer.
NOTE: Pressing the foot pedal opens the container only 3" to
6" (7.6 cm to 15.2 cm), depending on the load.
Load bulky trash, bottles, and cans in the center of the drawer.
Bottles or cans not placed in the center may become caught
between the ram and the drawer. The Drawer Monitor Switch
then senses a “misload” and causes the ram to return to the “up”
position without compacting.
7
2. Place trash in compactor.
■ Wrap or cover wet or messy trash.
■
Do not compact items that may develop offensive odors
such as raw meat, fish, grapefruit rinds, disposable
diapers, or personal hygiene items.
■
Load bottles or cans on their sides in the center of the
drawer. Do not load bottles in an upright position.
■
Press START. The compactor will automatically stop at
the end of the cycle.
2. To stop the compactor during a cycle:
■ Press OFF.
3. Close the drawer.
Starting the Compactor
Depending on your model, you may have a single control (Style 1)
or a dual control (Style 2) compactor.
■
Press ON. The compacting ram will rise. When the ram
stops rising, you can open the drawer.
To Remove the Key-Switch
1. Turn the Key-Switch to the OFF/LOCK position.
2. Remove and store key out of children’s reach.
Style 1
To Start and Stop the Compactor
1. To start the compactor, turn the Key-Knob to START and then
let go. The compactor will automatically stop at the end of the
cycle.
Removing a Filled Bag
2. To stop the compactor during a cycle:
■ Turn the Key-Knob to LOCK/OFF.
■
Then turn the Key-Knob to ON so the compacting ram
will rise.
■
When the ram stops rising, you can open the drawer.
When the trash is compacted to the top of the drawer, remove
the bag. If the bag is too heavy, compact less trash before
emptying it in the future.
IMPORTANT: Do not push items down into compactor with
hands or feet.
1. Pull the drawer completely open.
2. Remove top of bag from bag retainer buttons. Pull up all
4 bag cuffs. Close bag with twist tie provided.
To Remove the Key-Knob
1. Turn the Key-Knob to the LOCK/OFF position.
2. Remove the Key-Knob and store it out of children’s reach.
3. Push Side-Lock Latch down and tilt drawer side open.
Style 2
To Start and Stop the Compactor
1. To start the compactor:
■ Turn the Key-Switch to ON.
■
8
Press ON.
4. Lift out bag.
Installing a New Bag
Do not use any kind of bag other than those designed especially
for use in your compactor. Order replacement compactor bags
through your local dealer or by calling the toll-free number on the
cover or in the “Assistance or Service” section.
IMPORTANT:
Before installing a new bag, be sure:
■ The drawer side is securely locked.
■
2. Lock bag in place by pulling the 4 prepunched holes over the
bag retainer buttons. Holes will expand over the buttons
without damaging the bag.
3. Press inside of bag against the drawer bottom, sides and
corners for a smooth fit.
The container is clean and free of debris.
1. Place folded bag into the drawer. Open bag and pull top
edges over the drawer top.
COMPACTOR CARE
Your new compactor is designed to give you many years of dependable service. However, there are a few things you are expected to do
in order to properly maintain your compactor. This section will tell you how to clean and care for your compactor.
Cleaning
Before cleaning the compactor, turn the Key-Knob (or KeySwitch) to the OFF & LOCK position and remove it.
NOTE: Any services other than those outlined in this section
should be performed by a designated service representative.
3. Hold the lever-action lock down and tilt the side of the drawer
out until the lock clears the drawer front.
NOTE: If desired, the drawer side can be removed by tilting it
up, then lifting it out.
Cleaning Exterior Surfaces
1. Wash exterior surfaces (including stainless steel) with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Rinse and dry thoroughly
with a soft cloth.
2. Wipe up spills right away. Some foods can damage the finish
if left on the compactor surface.
Cleaning Inside the Drawer
NOTE: You may want to wear gloves since there may be bits of
glass in the drawer.
1. Remove the bag. See “Removing a Filled Bag.”
2. Press down on the lever-action lock (or Side-Lock latch).
4. Wash the interior of the drawer with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
5. If the drawer side was removed, slide it back into the tilted
position.
6. Press the lever-action lock (or Side-Lock Latch) down while
pushing the drawer side to the upright position.
7. Latch the drawer side by pushing up the lever-action lock (or
Side-Lock Latch).
Cleaning Inside the Cabinet
NOTE: You may want to wear gloves since there may be bits of
glass in the cabinet.
1. Pull the drawer out until it stops.
9
NOTE: Look to see how the drawer rollers move in the tracks.
It will be easier to replace the drawer after you have finished
cleaning.
5. Wash the inside of the cabinet with a clean sponge or soft
cloth and a mild detergent in warm water. Rinse and dry
thoroughly with a soft cloth.
6. To replace the drawer, grasp it by the sides and insert the
rollers onto the tracks.
7. Lift the front of the drawer and push it in fully past the stops.
Cleaning the Ram
2. Lift the front of the drawer to clear the stops.
3. Grasp the drawer on the sides and pull it out the rest of the
way. Set the drawer down gently.
NOTE: You may want to wear gloves since there may be bits of
glass on the ram cover.
1. Wipe glass particles off of the ram cover with a cloth or paper
towels.
2. Remove foods with a clean sponge or soft cloth and a mild
detergent in warm water. Rinse and dry thoroughly with a soft
cloth.
4. Vacuum the inside of the cabinet. Liquid spills or wet trash
should be cleaned up by hand, or by using a vacuum cleaner
designed to pick up liquids.
Cleaning Before a Vacation
If you will be away for more than a couple of days, remove the
compactor bag. Remove the Key-Knob (or Key-Switch) and store
it out of children’s reach.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Trash is not compacting
Is the drawer less than half-full? Drawer must be more than
half full before trash is compacted.
■
The drawer won’t open
■
To raise the ram on models with a Key-Knob (or KeySwitch): Turn the Key-Knob (Key-Switch) to START and
release. See “Starting the Compactor.”
Your compactor won’t operate
■
Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
■
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
■
Is the drawer completely closed? Close the drawer firmly
and start the compactor again.
■
Is the Key-Knob turned all the way to START? Turn the
Key-Knob (Key-Switch) fully to START and release (on some
models). See “Starting the Compactor.”
■
Did you press ON before pressing START? Press ON
before pressing START (on some models). See “Starting the
Compactor.”
10
Is the ram all the way up? Drawer will open only when ram is
fully raised.
To raise the ram on models with push button controls:
Press OFF, and then press ON. See “Starting the Compactor.”
■
Is the Solid Cycle engaged? Drawer remains LOCKED until
you reset by lifting the foot pedal up.
There is not enough compaction or force
■
Do you use the compacting cycle frequently enough?
Compacting works best when only a few items are loaded.
Bottles don’t break
■
How often do you notice this? Bottles will not break every
time. The thickness of the bottle’s glass and the content of
the trash load below it may keep the bottle from breaking.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use FSP® factory specified parts. These parts will fit right
and work right because they are made with the same precision
used to build every new WHIRLPOOL® appliance.
To locate FSP® factory specified parts in your area, call us or your
nearest designated service center.
In the U.S.A.
Call the Whirlpool Customer eXperience Center
toll free: 1-800-253-1301 or visit www.whirlpool.com.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
Our Consultants Provide Assistance With:
■
Features and specifications on our full line of appliances.
■
Installation information.
■
Use and maintenance procedures.
■
Accessory and repair parts sales.
■
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
■
Referrals to local dealers, repair parts distributors and service
companies. Whirlpool designated service technicians are
trained to fulfill the product warranty and provide afterwarranty service, anywhere in the United States.
For Further Assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
Call the Whirlpool Canada LP Customer eXperience Centre toll
free: 1-800-807-6777 or visit our webpage www.whirlpool.ca.
Our Consultants Provide Assistance With:
■
Features and specifications on our full line of appliances.
■
Use and maintenance procedures.
■
Accessory and repair parts sales.
■
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool Canada LP designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For Further Assistance
If you need further assistance, you can write to Whirlpool
Canada LP with any questions or concerns at:
Customer eXperience Centre
Whirlpool Canada LP
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
Accessories
To ensure the proper functioning of your compactor, use FSP®
factory specified parts only. To order replacement parts or
accessories, call 1-800-253-1301 and ask for the appropriate
part number listed below or contact your authorized Whirlpool
dealer. In Canada, call 1-800-807-6777.
■
Replacement Bags: Call to get Part Number.
■
Installation Hardware for Conversion Kits:
Part Number 9870118
11
WHIRLPOOL® COMPACTOR WARRANTY
ONE-YEAR FULL WARRANTY ON COMPACTOR
For one year from the date of purchase, when this compactor is operated and maintained according to instructions attached to or
®
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP will pay for FSP factory specified parts and repair labor
costs to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
Whirlpool Corporation or Whirlpool Canada LP will not pay for:
1. Service calls to correct the installation of your compactor, to instruct you how to use your compactor, to replace household fuses, or
to correct household wiring.
2. Repairs when your compactor is used in other than normal, single-family household use.
3. Pickup and delivery. Your compactor is designed to be repaired in the home.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products not
approved by Whirlpool Corporation or Whirlpool Canada LP.
5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Charcoal filters.
8. In Canada, travel or transportation expenses for customers who reside in remote areas.
WHIRLPOOL CORPORATION OU WHIRLPOOL CANADA LP SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or
province to province.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine
if another warranty applies.
If you need service, first see the “Troubleshooting” section of this book. After checking “Troubleshooting,” additional help can be found
by checking the “Assistance or Service” section or by calling the Whirlpool Customer eXperience Center, 1-800-253-1301 (toll-free),
from anywhere in the U.S.A. In Canada, contact your Whirlpool Canada LP designated service company or call 1-800-807-6777.
3/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your compactor to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the inside wall of the compactor drawer.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number __________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
9872208C
®
/™ ©2013 Whirlpool. Used under license in Canada. All rights reserved.
11/13
Printed in U.S.A.