DVD/Blu-ray
Duplicator
User Guide
V5.30
the Expert of Duplicators
www.ureach-inc.com
Content Index
Chapter 1. Basic Introduction
1.Features
2.System Overview
2-1. Package Content
2-2. Other components necessary for
assembling the Duplicator
2-3. SATA controller hardware Installation
guide
3
4
4
4
5
Chapter 2. Function Operation
Function Table-CD/DVD/BD Duplicator
9
1.Copy
10
2.Test
10
3.Compare
11
4.Copy + Compare
12
5.Set Burn Speed
12
6.Select Source
13
7.Utility
7-1. Information
13
7-2. Erase Disc
14
7-3. PreScan Source
15
7-4. Track Edit
16
7-5. Eject All Disc
16
7-6. Copy Counter
16
7-7. Update BIOS
17
7-8. PRINT LS Label
17
8.Setup18
18
8-1. Auto Start Time
8-2. Display Mode
18
8-3. Button Beep
19
8-4. Eject On Start
19
8-5. Reader Speed
19
8-6. Compare Speed
19
8-7. Language
19
8-8. Clear Setup
19
19
8-9. Advanced Setup
9.HDD Manager (For HDD-installed duplicator) 21
9-1. Select Image
21
9-2. Disc to Image
21
9-3. Set Reader Speed
22
9-4. Show Image Info.
22
9-5. Rename Image
22
9-6. Delete Image
23
9-7. Show HDD Info.
23
2
9-8. Format HDD
9-9. Load & Copy
24
24
Chapter 3. Specification
Chapter 4. Appendix
Lightscribe Operation26
Error Message30
Chapter 1. Basic Introduction
1.Features
●● No PC needed. Independent SATA to SATA DVD / Blu-ray Disc Duplication.
●● Sepcial Ssynchronous Load and Copy technology. When the system was installed
with HDD, the system will load master source disc to HDD while copying disc to
disc. In 2nd run copy, the system will automatically copy from HDD instead of from
the source reader.
●● Support high speed 20× DVD, 52× CD, 8× Blu-ray burning.
●● High compatibility with variety brands of burner.
●● Easy assembly SATA port arrangement
●● Support Lightscribe printing
3
Chapter 1. Basic Introduction
2.System Overview
2-1. Package Content
OK
ES
C
Controller
SATA Cables(180˚)
User Manual
2-2. Other components necessary for assembling the Duplicators
HDD
CD/DVD-ROM
CD/DVD-RW
Writer
User Manual
4
Chapter 1. Basic Introduction
2-3. SATA Controller Hardware Installation Cuide
Example: 1-4 installed
OK
ESC
1.(ROM)
Write 1
2
Write 2
3
Write 3
4
1
4
Write 4
2
3
5
5
Write 5
OK
ES
C
Example: 1-7 installed
OK
ESC
HDD
1.HDD (Master)
ROM (Slave)
Write 1
2
Write 2
3
Write 3
4
1.Mas
ter
3
Write 4
5
6
7
4
Slave
2
5
8
Write 5
6
Write 6
7
Write 7
8
OK
ES
C
Write 8
5
Chapter 1. Basic Introduction
Example: 1-11 installed
OK
ESC
HDD
1.HDD (Master)
ROM (Slave)
Write 1
2
Write 2
3
Write 3
4
Write 4
5
Write 5
6
Write 6
7
Write 7
8
1.Mas
ter
Write 8
5
9
Write 9
10
6
8
9
10
Slave
11
12
Write 10
11
Write 11
12
Write 12
6
2
7
OK
ES
C
3
4
Chapter 2. Function Operation
Function Table-CD/DVD/BD Duplication
Function
Sub-function
Description
1. Copy
To copy disc to disc or copy disc from HDD.
2. Test
To simulate copy process
3. Compare
To bit by bit compare between source disc and copied discs
4. Copy & Compare
To copy first and compare the copied discs later. To ensure data
correctness.
5. Set Burn Speed
To set burning speed for duplication.
6. Select Source
To select source from any optical drive or hard disk drive.
1. Information
2. Erase Disc
1. Disc Info.
To check the format of disc, burning speed supported and total capacity
or data size.
2. Drive Info.
To check the version, model No. and brand name
3. System Info.
To check the model No. and firmware version
1. Quick Erase
To quick erase data from rewritable disc.
2. Full Erase
To full erase data from rewritable disc.
3. PreScan Source
7. Utility
4. Track Edit
To check source disc’s readability.
1. Copy Track
To select and combine audio tracks from various CDs into a single
customized audio CD.
2. Close Disc
To close the disc after track copying to make the CD playable on CD
player.
3. Disc Info.
To check the audio CD’s status of usage.
5. Eject All Disc
6. Copy Counter
To eject all trays.
1. Show Count
To check how many discs copy successfully and failed.
2. Enable Counter
To enable or disable counter setting.
3. Clear Counter
To delete the record.
7. Update BIOS
To update the system’s firmware.
8. PRINT LS Label
To print Lightscribe image.
7
Chapter 2. Function Operation
Allow the system to do the Copy, Test, Compare and Copy + Compare
functions automatically
1. Auto Start Time
1. Basic
2. Display Mode
2. Show Timer
3. Show Speed
3. Button Beep
4. Eject On Start
8. Setup
1. Eject All Discs
To eject all trays with disc inside once the system is booted up.
2. Do Not Eject
No eject any tray or disc once the system is booted up.
3. Eject Target Only
Only eject target trays with disc inside once the system is booted up.
4. Eject Source Only
Only eject source disc once the system is booted up.
5. Eject All Trays
To eject all trays once the system is booted up.
5. Reader Speed
To adjust the reading speed of source drive.
6. Compare Speed
To adjust the speed of drives while comparing.
7. Language
8. Clear Setup
9. Advanced Setup
9. HDD Manager
To reset all the function back to manufacturer’s default setting.
1. Power On Time
To set a warm-up time from 5 seconds to 99 seconds
2. Startup Menu
To select which function you would like to show up in the beginning
3. Skip Reader Error
To set skip the read error and keep copying.
4. Change Bad
Master
To make the system eject source disc and ask for another one while
the source disc is unreadable for system.
5. CD Overburn
Set to copy overburn CD.
6. Show HDD
Image Name
To show HDD image name or capacity on Copy, Test, Copy + Compare
and Compare function
7. Keep Buffer
To set enable or disable load source to the buffer.
8. Boot Password
To enable or disable the user administrative password.
9. Setup Password
To set up the login password
10. Count Password
To set up counter login password.
1. Select Image
To select image file from HDD as your source for copy.
2. Disc=> Image
To load your source disc to the built-in HDD.
3. Set Reader Speed
To adjust the speed of source reader while you load image file from the
reader to HDD.
4. Show Image Info.
To check the disc format and data size of image file
5. Rename Image
To change the name of image file
6. Delete Image
To delete image file in the built-in HDD
7. Show HDD Info.
To check the information of the built-in HDD includes how many discs
are stored and the free space is available
8. Format HDD
9. Load & Copy
8
To format the built-in HDD
1. Load First
To load the source to HDD and make copy at the same time.
2. Synchronous
To load source to HDD first and copy from HDD to disc.
3. OFF
To disable Load & Copy function.
Chapter 2. Function Operation
1.Copy
It is important to make sure that your source disc is placed in the right drive. You can check or
select your source reader by 6.Select Source. (plase refer to 6.Select Source, page 11)
1.Select 1.Copy and place source disc and blank discs into the proper trays. Then the system
will detect the source disc and show the information.
Q'ty of target disc
Data size
2.Press
to start copy
Q'ty of target
Data size
Speed of burning
Copied data size
Copy process %
3. Once the copy task is finished, the copied discs will be ejected and the result of copy task
will show on the LCD:
Elapsed time
**Note:
Due to default setting of auto start time, the duplicator will start to copy automatically
within a few seconds. You can set “OFF” to close the auto start function or set a longer
waiting time. The default setting is 5 seconds. (About this setting please refer to 8-1.
Auto Start Time, page 17 )
If HDD is selected to be the source reader, you have to upload the source to the built-in
HDD and then follow copy process to do your copy task. How to upload data from disc to
HDD please refer to 9-2.Disc to Image, page 21.
**Note:
The default setting of source reader is the first drive.
9
Chapter 2. Function Operation
2.Test
This function will simulate the copy process to ensure error free duplication. During the
simulation, it will be nothing left in the recordable discs.
1.Using
/
to select 2.Test and press
2.Press
to start test
.
3. Once the test task is finished, the discs will be ejected and the result of the pass and fail
discs for the test task will show on the LCD:
**Note:
1 This function is unable to support DVD+R blank disc.
2 If you use CD/DVD rewritable discs as your blank media in the simulation, all the
content inside the discs will be erased permanently during test simulation.
3.Compare
This function will do bit-by-bit comparison between source disc and copied discs to ensure the
copied discs are identical to source disc.
1. Place source disc and blank discs into Reader and Writer separately.
2.Using
10
/
to select 3.Compare and press
to start compare.
Chapter 2. Function Operation
3. The system will detect the source and target discs automatically.
4. After detecting, the system will start to compare.
5. When the comparison has finished, the system will show the compare result.
4.Copy + Compare
This function will to do copy task first and execute comparison automatically when copy process
has been finished.
**Note:
In Copy, Test, Compare and Copy+Compare functions
1 If there is no source and target discs inside the duplicator, there will be nothing
show on LCD.
2 If the built-in HDD is selected as source, the information presents different:
3 The information display of these 4 functions will be different based on the
Image file name
display mode you selected.
(Plase refer to 8-2.Display mode, page 17)
11
Chapter 2. Function Operation
5.Set Burn Speed
You can adjust the burning speed of CD/Audio CD/DVD/DVD DL/Blu-ray by this setting. The
default setting of CD is 40X, Audio CD 24X, DVD 8X, DVD DL 2X and Blu-ray 2X.
1.Using
/
to select 5.Set Burn Speed and press
.
2.Pressing
/
to adjust the burning speed of CD and press
to confirm it, or press
to select Audio CD,DVD, DVD DL or Blu-ray to adjust the burning speed.
6.Select Source
You can set any drive or built-in HDD in the duplicator to be your source reader.
1.Using
/
to select 6.Select Source
2.Press
to check the current source reader, or select the proper drive to be the source
reader by pressing
/
, once the source reader is selected, press
to confirm the
setting and back to the menu list.
**Note:
The default setting of source reader is the first drive.
12
Chapter 2. Function Operation
7.Utility
7-1. Information
You can check the information of disc, drive and system by this function. By pressing
each disc or drive’s information will show on the LCD.
1.Using
/
to select 7.Utility, press
1.Information and press .
/
,
to enter the sub menu. Then, select
2.Using
/
to select 1.Disc Info. or 2.Drive Info or 3.System Info., and press
to see
the related information.
3. The information will show on the LCD as below:
●● Disc Info.: You can check the format of disc, burning speed supported and total
capacity. If the disc has data inside, you also can check the size of data.
Burning Speed
Disc Format
Capacity/Data size
●● Drive Info.:
1. HDD:you can press the button
,to check your HDD Brand&Model name.
2. Drive:The version,model No.and brand name can be checked here.
Drive version
Brand name
13
Chapter 2. Function Operation
●● System Info.: The model No. and firmware version can be checked here.
7-2. Erase Disc
This function will erase the rewritable discs in WRITER tray, there are two erase modes available:
●● Quick Erase: It will erase the INDEX of the rewritable disc.
●● Full Erase: It will erase ALL DATA in the rewritable disc, which takes longer time than Quick
Erase.
1. Place discs into writers.
2.Using
/
and press
3.Using
/
to select 7.Utility and press
to enter the sub menu. Then, select 2.Erase
.
to select 1.Quick Erase. or 2.Full Erase.
OR
4.Pressing
to execute the erasing task. When the system is detecting the discs, you will
see the colon flashing.
The Second Drive
5. When the erase job is in process, you should see the O and o are blinking by turns.
14
Chapter 2. Function Operation
6. Once the erase task has finished, the O stop blinking, the disc will be ejected automatically.
**Note:
1 If you see F and f are blinking by turns, which means the whole new DVD+RW is in
format process.
2 Erase function only support rewritable discs.
7-3. PreScan Source
This function will scan and detect any bad sectors existing in the source disc, which helps you
to ensure the readability of source disc.
1. Place a source disc into reader.
2.Using
/
to select 7.Utility and press
to enter the sub menu. Then, select
3.Prescan Source and press
to start scan task.
3. When prescan task is in process, you can see the process on the display:
Data size
Elapsed time
Scanned data size
Scan process %
4. When the prescan task has finished, the result of prescan will be shown on the LCD.
15
Chapter 2. Function Operation
7-4. Track Edit
This function enables you to combine audio tracks from various CDs into a single customize
audio CD.
●● Copy Track: You can select and combine audio tracks from different CDs in this section.
●● Close Disc: You have to perform this function after copy track to make the CD playable on
CD player.
●● Disc Info.: You can check the audio CD’s status of usage.
7-5. Eject All Disc
You can eject all discs including source and target discs at the same time by this function.
7-6. Copy Counter
This function will record the result of duplication.
●● Show Count: You can check how many discs copy successful and failed.
●● Enable Counter: You can set the counter enable or disable to record the copy result.
●● Clear Counter: You can delete the record by this function.
1.Using
/
to select 7.Utility and press
Counter and press
.
2.Using
3.Pressing
/
to enter the sub menu. Then, select 6.Copy
to select 1.Show Count.
to check the calculation of successful and failed duplication for CD and DVD
Q'ty of passed CD
Q'ty of failed CD
16
Chapter 2. Function Operation
7-7. Update BIOS
You can update the system’s firmware in this function.
1. Place manufacturer certified update file CD into any drive
2.Pressing
/
to select 7.Utility and sub menu 7.Update BIOS and then press
start the process.
to
3. The system will detect the update file and execute update task automatically.
4. Once the update job has done, the system will require you to reboot the system.
**Note:
Do NOT save the firmware in a folder. The system can not detect the file if you save it in
a folder.
7-8. PRINT LS Label
This function will let you using the Lightscribe technology to print your own image on discs.
The operation process please refer to Appendix Lightscribe Operation.
17
Chapter 2. Function Operation
8.Setup
8-1. Auto Start Time
This setting will allow the system to do the Copy, Test, Compare and Copy + Compare functions
automatically in a few seconds once the source and blank discs are placed in the trays and
detected by the system. The default setting is 5 seconds. You can set a longer/shorter time from
1 to 99 seconds or set OFF to disable this function and execute copy task by manual.
1.Pressing
/
to select 8.Setup and sub menu 1.Auto Start Time.
2.Pressing
/
to set the time.
8-2. Display Mode
You can select the prefered display mode in Copy, Test, Compare, Copy+Compare.
●● Basic: It will only show the copy process (%) on LCD.
Q'ty of target
Data size
Copy process %
Copied size
●● Show Timer: It will show the time for copy.
Elapsed time
●● Show Speed: It will show the speed of burning during copy process.
Speed of burning
18
Chapter 2. Function Operation
8-3. Button Beep
This setting will allow you to set up to hear a beep when a button is pressed or not.
8-4. Eject On Start
You can make the trays or discs eject once the system is booted up.
●● Eject All Discs: To eject all trays with disc inside once the system is booted up.
●● Do Not Eject: No eject any tray or disc once the system is booted up.
●● Eject Target Only: Only eject target trays with disc inside once the system is booted up.
●● Eject Source Only: Only eject source disc once the system is booted up.
●● Eject All Trays: To eject all trays once the system is booted up.
8-5. Reader Speed
This setting allows you to adjust the reading speed of source drive. The default setting of reader
speed of CD is 40X; DVD is 24X.
8-6. Compare Speed
The reading speed of drive and disc are the reasons can affect the quality of comparison. This
setting allows you to adjust the reading speed of drives to match up the reading speed of discs.
The default setting of CD’s compare speed is 40X, DVD is 8X.
8-7. Language
You can set a proper language for interface during operation.
8-8. Clear Setup
This setting will reset all the function back to manufacturer’s default setting.
8-9. Advanced Setup
●● Power On Time: You can set a warm-up time from 5 to 99 seconds for warming up the
duplicator when it is turned on. The default setting is 10 seconds.
●● Start-up Menu: You can select which function you would like to show up in the beginning.
●● Skip Read Error: You can set this function enable to skip disc errors in order to avoid bad
quality of copy. If you are confident of your source disc has only a small and insignificant
error due to physical damages and can be overlooked, you can set NO to disable this
function.
19
Chapter 2. Function Operation
**Note:
Skip Read Error can not fix the error in the source disc, all it does is skipping the errors
and keeps copying the rest of readable data.
●● Change Bad Master: This setting will make the system eject source disc and ask for another
one while the source disc is unreadable for system.
●● CD Overburn: The majority of discs have a small margin of extra groove at the outer edge.
This setting allows you to copy data over the normal size limit.
●● Show HDD Image Name: You can select to show HDD image name or capacity on Copy,
Test, Copy + Compare and Compare function.
Show HDD Image Name:
Show capacity:
**Note:
When you change the source from drive to HDD, the LCD will show the HDD information.
How to change your source reader please refer to 6.Select Source, page 11.
●● Keep Buffer: You can set Yes to load source disc to buffer in first round of Copy, Test,
Compare or Copy+Compare, and do it again without the source disc. Or you can set No to
keep buffer not be used.
**Note:
The source will be only temporary saved in buffer, there will be nothing left when you exit
the task (Copy, Test, Compare and Copy+Compare or reboot the system.
●● Boot Password: This setting allows you to enable or disable the user administrative
password. Users have to login when the system is booted on.
/
to select the number you
●● Setup Password: You can set up password by pressing
like and press
to set next number.
●● Count Password: You can select the disable/Enable mode and Count your login password.
20
Chapter 2. Function Operation
9.HDD Manager (For HDD-installed duplicator)
9-1. Select Image
You can select image file from HDD as your source for copy. When this function is selected, the
system will set the HDD to be the source reader automatically.
1.Pressing
/
to select 9.HDD Manager and sub menu 1.Select Image.
2.Pressing
/
to select the image you need and press
to confirm.
Data size
9-2. Disc to Image
This function will load your source disc to the built-in HDD and save the source as an image file.
1. Placing the source disc to any one of the drives
2.Pressing
/
to select 9.HDD Manager and sub menu 2.Disc to Image.
3.Pressing
to start loading.
21
Chapter 2. Function Operation
4. When loading has finished, the disc will be ejected automatically.
**Note:
The source disc can be placed in any drive, it will not affect the loading process.
9-3. Set Reader Speed
You can adjust the reading speed of the drive which you put the source disc. This function is
ONLY available when you loading the source disc to HDD. The default setting of both CD and
DVD speed are MAX.
9-4. Show Image Info.
You can check the disc format and data size of image file in this function.
1.Pressing
/
to select 9.HDD Manager and sub menu 4.Show Image Info.
2.Press
to check the disc format and data size of the image file. And you can press
to check other image file’s information.
/
9-5. Rename Image
This function allows you to change the name of image file. You can set maximum up to 8
characters for a new name, and NO blank is allowed between the characters.
22
Chapter 2. Function Operation
1.Pressing
/
to select 9.HDD Manager and sub menu 5.Rename Image.
2.Pressing
and select which image file you would like to rename by pressing
and then press
to start edit a new name for the selected file.
/
,
You can select characters or number by pressing
/ , and press
to the next space
to edit. The maximum is 8 characters without blank space. When it has done, press
to
confirm the new name.
9-6. Delete Image
You can delete image file from the built-in HDD, but the source image file is unable to delete
if the file is selected as source. Therefore, before you delete an image file, please check if it is
selected as a source and change a new one source by 9.1Select Image, page 20.
**Note:
If there is an image file is deleted, the file name will be held for next new image file, the
existing file will not to fill the vacancy. For example, there are 5 image files (A001~A005)
in the HDD, when you delete A003, A004 will not change to be A003, once a new file
has loaded, its default name will be A003.
9-7. Show HDD Info.
You can check the information of the built-in HDD includes how many discs are stored and the
free space is available in the HDD.
23
Chapter 2. Function Operation
9-8. Format HDD
This function allows you to format the built-in HDD while the HDD is NOT selected as reading
source. You can change the source from HDD to other drive in 6.Select Source, page 11.
Due to the capacity for discs loading is hard to predict precisely and more and more different
discs coming out. The traditional method of format is not ideal for using on this duplicator.
This duplicator is able to detect disc capacity and assign a proper partition for the disc’s data
automatically. You do not have to predict and select CD or DVD partition in the beginning and you
can check how many discs you can upload from 9-7.Show HDD Info., page 23 This intelligent
HDD management technology is much easier for HDD management than the old way.
9-9. Load & Copy
This function is for the system to load the source to HDD and make copy synchronously. The
system will load the source to HDD during the first round of duplication, and the HDD will replace
the reader drive to be the source in second round of duplication. This special function is very
convenient for a big copy task. You also can set:
●● Load First: The system will load source to HDD first and take HDD as source to copy.
●● Synchronous: The system will load the source to HDD and make copy at the same time.
●● OFF: To disable Load & Copy function.
**Note:
1 The image file will only be saved temporary if it is loaded to HDD by Load & Copy
function.
2 If you would like to save the file permanently please load the file to HDD by manual
(refer to 9-2.Disc to image, page 21)
24
Chapter 3. Specification
Model
P501D
P504D
P507U/W
P511U/W
P515X
Target
1
4
7
11
15
Buffer (DDR2)
64MB
128MB(U) / 512MB(W)
Interface
SATA
CD Speed
52X
DVD Speed
20X
Blu-ray Speed
8X
Writing Method
DAO, TAO, RAW
256MB
BD-ROM, BD-R, BD-RE
DVD-ROM, DVD-Video, DVD-Audio, DVD+R, DVD+RW, DVD-R, DVD-RW, Dual
Layer DVD±R,
Disc Format Support
CD-ROM, CD-RW, CD-I, Audio CD, Video CD, CD+G, CD-TEXT,
Bootable CD, Mixed-mode CD, Multi-session CD, CD-Extra,
Business Card CD, 3” Mini CD-R
Display
2x16 Backlight Monochrome LCD
Input
4 push buttons ( Forward, Backward, OK, Esc)
Language Support
English, Japanese, Chinese, Portuguese, Spanish
Working
5°C ~ 45°C
Storage
-20°C ~ 85°C
Working
20% ~ 80%
Storage
5% ~ 95%
Voltage
5V±5%
Current
3A Max
Temperature
Humidity
Controller Power
Consumption
Safety
Controller Weight (NW / GW) (g)
FCC, CE, RoHS
190 / 370
210 / 480
250 / 580
260 / 680
300 / 850
* The above information is for marketing reference only. The actual specification may subject to change without notice.
25
Chapter 4. Appendix
Lightscribe Operation
Step 1
Install Lightscribe template software to PC
Download LightScribe software from www.lightscribe.com and install below software.
A. LIGHTSCRIBE SYSTEM SOFTWARE (LSS)
A
B
B. LIGHTSCRIBE TEMPLATE LABELER.
26
Chapter 4. Appendix
Step 2
Execute "LightScribe Drive select.exe".exe file to select LightScribe Drives
1. Receive a .exe file from your supplier.
2. Execute the .exe file on your PC.
3. And select the LightScribe Duplicator drive on the list.
**Note:
When everytime the Duplicator change LightScribe drive, must re-select drive
before create LightScribe image for that Duplicator.
4. If the duplicator’s Lightscribe drive is not on the list, please follow below steps to add new
lightscribe drive to the support list.
❶ Plug the new lightscribe drive you will use for Duplicator to the PC.
❷ Click "Detect Lightscribe Drive And Disc " to search new available lightscribe drive.
❸ Select the new drive and press
, the drive will be added to the list.
27
Chapter 4. Appendix
Step 3
Design Lightscribe Template and Lightscribe printing on PC.
1. Click to launch the LightScribe Template
on our PC.
2. Follow procedure to create your label image.
3. Make sure the lightscribe drive is selected.
**Note:
If Lightscribe template can not be executed normally under Window7, please try
to click right button on the mouse on the Lightscribe icon and select " Run as
administrator" to execute the function.
4. Click the Print to save the lightscrbe image .LSI file to a USB stick or a Disc.
❸
❹
28
Chapter 4. Appendix
5. Plug the USB drive or Disc into Duplicator.
6. Select the utility function 7-8.PRINT LS Label. The system will read the image into the
duplicator and start printing the lightscribe label.
Data side
Print side
**Note:
When doing the lightscribe printing, please turn over the disc. The print side is face
down and data side is face up.
29
Chapter 4. Appendix
Error Message
Error Message
Possible Reasons
Toubleshooting
Master disc is empty or protected.
Bad Master Disc
Please check your master disc by (1) Disc Info (2) by PC.
Master disc has demaged or bad quality
Warning:
Can’t DVD↑CD
You put different format of blank disc from the master disc.
Can not copy between different disc format
Please check your master and blank disc foramt by " Disc
info". Only can copy CD to CD, DVD to DVD.
Not Blank Disc
The target disc has been written.
Please use blank disc or rewrittable disc.
No blank disc. Or the disc is upsite down.
No Disc
Using Blu-Ray blank disc, but the driver does not support BluRay.
Please double check again your target disc.
No source disc
Please check if you put the right source disc into the drive.
Use Blu-Ray as a source, but the driver does not support BluRay.
Please check the disc format by "Disc Info".
Master disc has bad quantity.
Please change another source.
Master disc is a protected disc
Please don't use protected disc as a source.
No update file
No disc with updated FW, can't find FW files
1. Check if you unzip the FW file.
2. Check if the FW is placed at root level.
3. Check if you put the right disc with FW.
4. Try the FW disc with other drives.
HDD Full !
HDD has no enough space
Please relase HDD space.
Wrong Password
Insert wrong password
Please double check again your password.
No Master Disc
Read Error Count
Over Limit
(happen when you load data from disc to
HDD)
30