Shindaiwa 89282 Operator`s manual

SHINDAIWA GRASS TRIMMER TO BLADE CONVERSION
INSTRUCTIONS
Model 89282 For Trimmer T282
WARNING!
Minimize the risk of injury to yourself and others! Read the Owner's/Operator's manual originally supplied with the unit that is being upgraded and
familiarize yourself with the contents. Always wear eye and hearing protection when operating your unit.
X7672820101
08/10
Introduction
These are instructions to convert a grass trimmer to a blade capable unit. This is not an Owner's/Operator's manual. Information on how to operate and maintain the unit can be found in the Owner's/Operator's manual for the unit you are converting. Note this kit is supplied with a cutting attachment shield that has been redesigned to provide better visibility and a
larger cutting swath when used as a grass trimmer.
IMPORTANT!
IMPORTANT!
If the cutting attachment shield has been removed from
your unit or the unit was manufactured prior to October
2001, an additional clamp kit will be required to complete
this installation. The clamp kit required is Shindaiwa part
number 80293.
Contents
The information contained in these instructions describes
the product available at the time of publication.
Echo, Inc. reserves the right to make changes to products
without prior notice, and without obligation to make alterations to units previously manufactured.
PAGE
PAGE
PAGE
Attention Statements.........................2
General Safety Instructions...............3
Assembly...........................................4
Safety Labels.....................................3
Kit Contents.......................................3
Shoulder Strap..................................8
Using a Brushcutter Blade.................8
Attention Statements
Throughout this manual are special “attention statements”.
WARNING!
A statement preceded by the triangular attention symbol and the word “WARNING” contains information that should be
acted upon to prevent serious bodily injury.
CAUTION!
A statement preceded by the word “CAUTION” contains
information that should be acted upon to prevent mechanical
damage.
IMPORTANT!
A statement preceded by the word “IMPORTANT” is one that
possesses special significance.
NOTE:
Read and follow this
operators manual.
Failure to do so could
result in serious injury.
Wear eye and hearing
protection at all times
during the operation
of this unit.
Keep bystanders
at least 50 feet (15 m)
away during operation.
Beware of thrown or
ricocheted objects.
A statement preceded by the word “NOTE” contains information
that is handy to know and may make your job easier.
IMPORTANT!
The instructions described in this manual are intended to help
you get the most from your Shindaiwa power tool as well as
to protect you and others from harm. These procedures are
guidelines for safe operation under most conditions, and are
not intended to replace any safety rules and/or laws that may
be in force in your area. If you have questions regarding your
Shindaiwa power tool, or if you do not understand something in
these instructions, your Shindaiwa dealer will be glad to assist
you. You may also contact Shindaiwa at the address printed on
the back of this instructional manual.
2
Do not operate this unit
with a blade unless the
unit is equipped with a
Shindaiwa-approved
handlebar or barrier.
Always wear a harness
when operating this unit
with a blade. A harness
is also recommended when
using trimmer line.
If unit is used as a
brushcutter, beware of
blade thrust. A jammed
blade can cause the unit
to jerk suddenly and may
cause the operator to
lose control of the unit.
Safety Labels
IMPORTANT!
Safety and Operation Information Labels: Make sure
all information labels are undamaged and readable.
Immediately replace damaged or missing information
labels. A new label is provided in this kit and additional
labels are available from your local authorized Shindaiwa dealer. Prior to installing the new label, Remove
old label and clean the outer tube with rubbing alcohol
or similar cleaner.
General Safety Instructions
WARNING!
■■When operating with a blade, make sure the handle
is positioned to provide you with maximum protection from contacting the blade. Always make sure the
handlebar is installed in accordance with the manufacturers instruction.
■■NEVER use a cracked or warped blade: If a properly
installed blade vibrates, replace it with a new one and
re-check.
■■ALWAYS Shut off the engine immediately if a blade
binds in a cut. Push the branch or tree to ease the
bind and free the blade.
■■Beware of a coasting blade when brushcutting or
edging. A coasting blade can injure while it continues to spin after the throttle trigger is released or
after the engine is stopped.
Kit Contents
2
1
10
13
4
5
14
3
6
15
9
12
11
8
#
Description
Qty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Debris Shield
Debris Shield Extension
M5 x 45 mm SPW Bolt
Upper Clamp
Spacer
Shoulder Strap
Hanger
M5 x 12 mm Socket Head Cap Screw
M5 Nut
Barrier Bar
Bolt Guard
8 x 22 mm Bolt
Holder (A)
Holder (B)
Safety Label
1
1
4
1
2
1
1
1
1
1
1
1
1
1
1
7
3
Assembly
Removing the Existing Cutting Attachment Shield
1. Remove the four socket-head cap screws (A),
bracket (B) and two shims (C).
2. Remove the cutting attachment shield from the
gearcase.
A
B
C
C
Remove Gear Case
D
1. Remove gear case locating screw (D) and loosen
gear case clamp (E).
2. Remove gear case from outer tube.
Remove Handle Assembly
1. Remove handle assembly. Retain all parts for
future use.
4
E
Install Hanger
1. Slide hanger (A) onto outer tube & position as
shown. Attach with 5x12 socket head cap screw,
but do not tighten at this time.
A
Handle
Install Handle and Barrier Bar
1. Install handle and barrier.
Install Gear Case
1. Install gear case onto outer tube. Align locating hole
on gear case with locating hole in tube.
A
2. Install locating bolt (A) and tighten clamp bolt (B).
B
5
Install New Cutting Attachment Shield
Assemble the Cutting Attachment Shield to the Outer Tube.
1. Insert the cutting attachment shield
(A) between the outer tube and the
cutting attachment mounting plate (B).
A
E
2. Fit the two shims (C) and the upper
clamp (D) over the outer tube and install the four socket-head cap screws
(E) finger tight.
CAUTION!
D
G
C
Make sure the clamp screw and retaining nut (F) are securely tightened
before tightening the four socket head
screws.
3. Tighten the four socket-head cap
screws to secure the cutting attachment shield.
A
C
B
F
Sub-Shield.
WARNING!
NEVER operate the unit without the cutting attachment
shield installed and tightly secured!
WARNING!
A cutting attachment shield or other protective device is
no guarantee of protection against ricochet. YOU MUST
ALWAYS GUARD AGAINST FLYING DEBRIS!
(when trimmer head is in use)
1. Attach the sub-shield (G) extension to
the cutting attachment shield (A).
WARNING!
NEVER use this machine without sub-shield when using a trimmer head.
CAUTION!
Make sure the sub-shield is completely hooked at the
hook receiver.
6
Installing Brushcutter Blade
1. Turn the unit over so that the gearcase output shaft faces UP.
2. Align the hole in the holder with the notch in the gearcase flange, and then
temporarily lock the output shaft by inserting a hex wrench through both
holes.
3. While holding the hex wrench turn the trimmer head clockwise to remove.
Remove the hex wrench.
F
4. Remove trimmer head holder (F).
5. Install blade holder (A) onto output shaft (G).
6. Align the hole in blade holder (A) with the matching hole in the gear case
flange and then temporarily lock the output shaft by inserting a hex wrench
through both holes.
26107
7. Fit the blade over the flange on holder (A).
D
CAUTION!
C
Install the blade (E) so its printed surface is visible to the operator when the
brushcutter is in the normal operating position.
B
WARNING!
G
The blade must fit flat against the holder flange. The blade mounting
hole must be centered over the raised boss on blade Holder (A).
A
WARNING!
Holder (B) must fit flush against the blade and the splines engaged
to the output shaft.
8. Install blade holder (B) on the output shaft (G).
WARNING!
Do not attach any blade to a unit without proper installation of all required
parts. Failure to use the proper parts can cause the blade to fly off and seriously injure the operator and/or bystanders.
E
9. Install the bolt guard (C) and then the blade retaining bolt (D). Using the
combination spark plug wrench/screwdriver, tighten the bolt firmly in a
counter-clockwise direction.
10.Remove the hex wrench.
B
The unit should now be completely assembled and ready for use with a
blade.
IMPORTANT!
Units with adjustable carburetors must be readjusted for blade use, otherwise
serious engine damage can occur.
WARNING!
A standard grass trimmer unit with loop handle should NEVER be operated with blade-type attachments. For blade use,
the trimmer must be fitted with a bicycle-type handlebar or barrier bar that is located in front of the operator to reduce the
risk of the operator coming in contact with the cutting attachment. (Per ANSI B175.3). When using a blade, the unit must
be equipped with a harness or strap.
7
Shoulder Strap
Adjust the shoulder strap so the shoulder pad rests comfortably on the off-side
shoulder and the cutting path of the cutting attachment is parallel to the
ground. Tighten hanger screw.
WARNING!
Always wear a shoulder strap when operating this unit with a blade. A
shoulder strap is also recommended when using trimmer line.
NOTE:
Using a shoulder strap with a brush-cutter allows you to maintain proper
control of the unit and reduces fatigue during extended operation.
NOTE:
Although a shoulder strap accessory is not required for use with a grass
trimmer, a shoulder strap can increase operator comfort during extended
periods of operation.
Using A Brushcutter Blade
WARNING!
 Before working with a blade-equipped unit, always inspect and clean the area of objects that could interfere with or
damage the blade.
 Never use a blade near sidewalks, fence posts, buildings or other objects that could cause injury or damage.
 Never use a blade for purposes other than those for which it was designed.
 Whenever you strike a hard object with a blade, always stop the brushcutter and carefully inspect the blade for damage. NEVER OPERATE THE UNIT WITH A DAMAGED BLADE!
 A blade-equipped unit must be equipped with a bicycle-type handlebar or barrier as well as a harness or strap.
 Always make sure the cutting attachment shield is properly installed before operating the unit.
Blade Thrust
‘Blade thrust’ is a sudden sideways or backward motion of the brushcutter.
Such motion may occur when the blade jams or catches on an object such
as a sapling tree or tree stump. BE CONSTANTLY ALERT FOR BLADE
THRUST AND GUARD AGAINST ITS EFFECTS!
Eleven
O’Clock
Barrier Bar
A brushcutter’s barrier bar helps prevent the operator from moving forward,
or the unit moving rearward, thus preventing inadvertent bodily contact with
the blade. ALWAYS KEEP THE BARRIER BAR SECURELY IN PLACE ON
THE UNIT!
Shoulder Strap or Harness
A shoulder strap or harness provides additional protection against blade
thrust. In addition, a shoulder strap or harness gives significant support and
comfort to help ensure safe and efficient operation.
When operating a unit equipped with a blade, make sure both the handle/
barrier bar and shoulder strap or harness are adjusted to the size of the
operator using the unit.
The blade rotates counter-clockwise. For best performance and to minimize
being struck by debris, move the blade from right to left while advancing on
your work.
Position the blade so cuts are made between the blade’s 7 o’clock and
11 o’clock positions (as viewed from above). DO NOT cut between the 11
o’clock and 5 o’clock positions (shaded area).
8
DO NOT C
UT
Blade
Rotation
OK To Cut
Seven
O’Clock
Five
O’Clock
BCC17
NOTES
9
NOTES
10
NOTES
11
Consumer Product Support
If you require assistance or have questions concerning the application, operation or maintenance of this product you
may call the Shindaiwa Consumer Product Support Department at 1-877-986-7783 from 8:30 am to 4:30 pm (Central
Standard Time) Monday through Friday. Before calling, please know the model and serial number of your unit.
ECHO Incorporated.
400 Oakwood Road
Lake Zurich, IL 60047-1564 U.S.A.
Telephone: 1-877-986-7783
Fax: 1-847-540-8416
www.shindaiwa.com
Copyright© 2010 By Echo, Incorporated
All Rights Reserved.
Yamabiko Corporation
7-2 Suehirocho 1-Chome, Ohme,
Tokyo, 198-8760, Japan
Phone: 81-428-32-6118
Fax: 81-428-32-6145