MICROWAVE OVEN
CE2974R (WHITE)
SERVICE
Manual
MICROWAVE OVEN
CONTENTS
1. Precaution
2. Specifications
3. Operating Instructions
4. Disassembly and Reassembly
5. Alignment and Adjustments
6. Troubleshooting
7. Exploded Views and Parts List
8. PCB Diagrams
9. Schematic Diagrams
SRSC
1. Precaution
Follow these special safety precautions. Although the microwave oven is completely safe during ordinary
use, repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as
potentially lethal high voltages and currents.
1-1 Safety precautions (
)
1. All repairs should be done in accordance
with the procedures described in this
manual. This product complies with
Federal Performance Standard 21 CFR
Subchapter J (DHHS).
2. Microwave emission check should be
performed to prior to servicing if the oven is
operative.
3. If the oven operates with the door open :
Instruct the user not to operate the oven and
contact the manufacturer and the center for
devices and radiological health immediatly.
4. Notify the Central Service Center if the
microwave leakage exceeds 5 mW/cm2
5. Check all grounds.
6. Do not power the MWO from a "2-prong"
AC cord. Be sure that all of the built-in
protective devices are replaced. Restore any
missing protective shields.
7. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control
knobs and compartment covers.
8. Make sure that there are no cabinet openings
through which people--particularly
children--might insert objects and contact
dangerous voltages. Examples: Lamp hole,
ventilation slots.
9. Inform the manufacturer of any oven found
to have emmission in excess of 5 mW/cm2,
Make repairs to bring the unit into
compliance at no cost to owner and try to
determine cause.
Instruct owner not to use oven until it has
been brought into compliance.
CENTRAL SERVICE CENTER
10. Service technicians should remove their
watches while repairing an MWO.
Samsung Electronics
11. To avoid any possible radiation hazard,
replace parts in accordance with the wiring
diagram. Also, use only the exact
replacements for the following parts:
Primary and secondary interlock switches,
interlock monitor switch.
12. If the fuse is blown by the Interlock Monitor
Switch: Replace all of the following at the
same time: Primary, door sensing switch
and power relay, as well as the Interlock
Monitor Switch. The correct adjustment of
these switches is described elsewhere in this
manual. Make sure that the fuse has the
correct rating for the particular model being
repaired.
13. Design Alteration Warning:
Use exact replacement parts only, i.e.,
only those that are specified in the
drawings and parts lists of this manual.
This is especially important for the
Interlock switches, described above.
Never alter or add to the mechanical or
electrical design of the MWO. Any design
changes or additions will void the
manufacturer's warranty.10.Always unplug
the unit's AC power cord from the AC
power source before attempting to
remove or reinstall any component or
assembly.
14. Never defeat any of the B+ voltage
interlocks. Do not apply AC power to the
unit (or any of its assemblies) unless all
solid-state heat sinks are correctly installed.
15. Some semiconductor ("solid state") devices
are easily damaged by static electricity. Such
components are called Electrostatically
Sensitive Devices (ESDs). Examples include
integrated circuits and field-effect
transistors.
Immediately before handling any
semiconductor components or assemblies,
drain the electrostatic charge from your
body by touching a known earth ground.
16. Always connect a test instrument's ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument's ground lead last.
1-1
Pretaution
1-2 Special Servicing Precautions (Continued)
17. When checking the continuity of the witches
or transformer, always make sure that the
power is OFF, and one of the lead wires is
disconnected.
18. Components that are critical for safety are
indicated in the circuit diagram by
shading,
or
.
19. Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications. A
replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
1-3 Special High Voltage Precautions
1. High Voltage Warning
Do not attempt to measureany of the high
voltages--this includes the filament voltage
of the magnetron. High voltage is present
during any cook cycle.
H. V. Capacitor
Before touching any components or wiring,
always unplug the oven and discharge the
high voltage capacitor (See Figure 1-1)
2. The high-voltage capacitor remains charged
about 30 seconds after disconnection. Short
the negative terminal of the high-voltage
capacitor to to the oven chassis. (Use a
screwdriver.)
H. V. Diode
3. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
Short
Touch chassis ground first then short to the high
voltage capacitor terminal by using screwdriver or
jumper wire.
PRECAUTION
PRECAUTION
There exists HIGH VOLTAGE ELECTRICITY with high
current capabilities in the circuits of the HIGH VOLTAGE
TRANSFORMER secondary and filament terminals. It is
extremely dangerous to work on or near these circuits
with the oven energized.
DO NOT measure the voltage in the high voltage circuit
including filament voltage of magnetron.
1-2
Never touch any circuit wiring with your hand nor with
uninsulated tool during operation.
PRECAUTION
Servicemen should remove their watches whenever
working close to or replacing the magnetron.
Samsung Electronics
2. Specifications
2-1 Table of Specifications
TIMER
99 MINUTES
POWER SOURCE
230V 50Hz, AC
POWER CONSUMPTION
MICROWAVE : 1,500W
GRILL : 1300W
OUTPUT POWER
FROM 100 TO 900W
(IEC-705 TEST PROCEDURE)
OPERATING FREQUENCY
2,450MHz
MAGNETRON
OM75PH(31)
COOLING METHOD
COOLING FAN MOTOR
OUTSIDE DIMENSIONS
517(W) x 297(H) x 424(D)
2-2 Comparison Chart
Samsung Electronics
AUTO REHEAT
O
AUTO COOK
O
POWER LEVEL
O
TIME SETTING AND WEIGHT
O
AUTO DEFROST
O
GRILL COOK
O
COMBI COOK
O
2-1
3. Operating Instructions
3-1 Control Panel
Auto Reheat Selection
Auto Cook Selection
Manual Cook Selection
Dual Cook Selection
Cooking Control Knob
Auto Defrost Feature Selection
Power Level Setting
Combi Mode Selection
Grill Mode Selection
Clock Setting
Turntable on/off
Stop/Cancel Button
Start Button/Dial Knob
(cook time, weight and serving dishes)
3-2 Features & External Views
Door
Ventilation Holes
Grill
Light
Safety Interlock Holes
Door Handle
Display
Control Panel
Glass Plate
Roller Ring
Door Latches
297mm
Coupler
517mm
3-1
424mm
Samsung Electronics
4. Disassembly and Reassembly
4-1 Replacement of Magnetron, Motor Assembly and Lamp
Remove the magnetron including the shield case,
permanent magnet, choke coils and capacitors (all
of which are contained in one assembly).
1. Disconnect all lead wires from the magnetron
and lamp.
2. Remove a screw securing the magnetron
supporter.
3. Remove the magnetron supporter.
4. Remove the air cover.
5. Remove screws securing the magnetron to the
wave guide.
6. Take out the magnetron very carefully.
7. Remove screws from the back panel.
8. Take out the fan motor.
9. Remove the oven lamp by rotating to pull out
from hole of air cover.
NOTE1: When removing the magnetron, make
sure that its antenna does not hit any
adjacent parts, or it may be damaged.
NOTE2: When replacing the magnetron, be sure
to remount the magnetron gasket in
the correct position and make sure the
gasket is in good condition.
Lamp
Cover Air
Thermo S/W
Fan Motor
Screw
Magnetron
H. V. Capacitor
H. V. Trans
4-1 Replacement of High Voltage Transformer
1. Discharge the high voltage capacitor.
2. Disconnect all the leads.
3. Remove the mounting bolts.
4. Reconnect the leads correctly and firmly.
PRECAUTION
Servicemen should remov their watches whenever
working close to or replacing the magnetron.
PRECAUTION
There exists HIGH VOLTAGE ELECTRICITY with high
current capabilities in the circuits of the HIGH
VOLTAGE TRANSFORMER secondary and filament
terminals. It is extremely dangerous to work on or
near these circuits with the oven energized.
DO NOT measure the voltage in the high voltage
circuit including filament voltage of magnetron.
Samsung Electronics
4-1
Disassembly and Reassembly
4-3 Replacement of Door Assembly
4-3-1 Removal of Door Assembly
Remove hex bolts securing the upper hinge and
lower hinge. Then remove the door assembly.
Upper Hinge
Screws
Lower Hinge
Screw
4-3-2 Removal of Door "C"
Insert flat screwdriver into the gap between Door
"E" and Door "C" to remove Door "C". Be careful
when handling Door "C" because it is fragile.
4-3-3 Removal of Door "E"
Following the procedure as shown in the figure,
insert and bend a thin metal plate between Door
"E" and Door "A" until you hear the 'tick' sound.
1. Insertion depth of the thin metal plate should be
0.5mm or less.
4-3-4 Removal of Key Door & Spring
Remove pin hinge from Door "E"
Detach spring from Door "E" and key door.
Door "E"
Key Door
4-2
Spring
Samsung Electronics
Disassembly and Reassembly
4-3-5 Reassembly Test
After replacement of the defective component parts of the door, reassemble it and follow the instructions below for proper
installation and adjustment so as to prevent an excessive microwave leakage.
1. When mounting the door to the oven, be sure to adjust the door parallel to the bottom line of the oven
face plate by moving the upper hinge and lower hinge in the direction necessary for proper alignment.
2. Adjust so that the door has no play between the inner door surface and oven front surface. If the door
assembly is not mounted properly, microwave energy may leak from the space between the door and
oven.
3. Do the microwave leakage test.
4-4 Replacement of Fuse
1. Disconnect the oven from the power source.
2. When 15A fuse blows out by the operation of interlock monitor switch failure, replace the primary
interlock switch, door sensing switch, monitor switch and power relay.
3. When the above three switches operate properly, check if any other part such as the control circuit board,
blower motor or high voltage transformer is defective.
4-5 Replacement of Drive Motor
1. Take out the glass tray, guide roller and coupler
from cavity.
Screw
2. Turn the oven upside down to replace the drive motor.
Drive Motor
3. Remove a screw securing the drive motor cover.
4. Disconnect all the lead wires from the drive motor.
5. Remove screws securing the drive motor to the
cavity.
6. Remove the drive motor.
7. When replacing the drive motor, be sure to
remount it in the correct position.
8. Connect all the leads to the drive motor.
Drive Motor Cover
Base Plate
9. Screw the deive motor cover to the base plate
with a screw driver.
10. Remount the coupler in the correct position.
Samsung Electronics
4-3
Disassembly and Reassembly
4-6 Replacement of Control Circuit Board
4-6-1 Removal of Ass'y Control Box
1. Be sure to ground any static electric charge in
your body and never touch the touch control
circuitry.
2. Disconnect the connectors from the control
circuit board.
SCREW
3. Remove screws securing the control box
assembly.
4. Remove the screw securing the ground tail of
the keyboard.
CONTROL BOX
4-6-2 Remonal of Ass'y P.C.B
1. Pull the lever end of the plastic fastener and
remove the Flexible Printed Circuit(FPC) of
membrane panel.
2. Remove screws securing the control circuit
board.
3. Lift up the control circuit board from the Ass'y
control box.
4. When reconnecting the FPC connector, make
sure that the holes on the connector are properly
engaged with the hooks on the Plastic Fastener.
4-4
screw
FPC
Connector
screw
Samsung Electronics
5. Alignment and Adjustments
PRECAUTION
1. High voltage is present at the high voltage terminals during any cook cycle.
2. It is neither necessary nor advisable to attempt measurement of the high voltage.
3. Before touching any oven components or wiring, always unplug the oven from its power source and discharge the high
voltage capacitor.
5-1 High Voltage Transformer
1. Remove connectors from the transformer terminals
and check continuity.
2. Normal resistance readings are as follows:
Secondary
Filament
Primary
Filament Terminals
Approx. 100W
Approx.0W
Approx.1.450W
(Room temperature = 20ûC)
Secondary
Terminal
Primary
Terminals
5-2 Low Voltage Transformer
1. The low voltage transformer is located on the
control circuit board.
2. Remove the low voltage transformer from the
PCB Ass'y and check continuity.
3. Normal resistor reading is shown in the table.
Terminals
Resistance
1~2(Input)
3~4(Output 2.9V)
5~6(Output13V)
1,000W
3.947W
2.117W
5-3 Magnetron
1. Continuity checks can indicate only an open
filament or a shorted magnetron. To diagnose an
open filament or shorted magnetron :
2. Isolate the magnetron from the circuit by
disconnecting its leads.
3. A continuity check across the magnetron filament
terminals should indicate one ohm or less.
4. A continuity check between each filament terminal
and magnetron case should read open.
Magnetron Antenna
Gasket Plate
Cooling Fins
Samsung Electronics
5-1
Alignment and Adjustments
5-4 High Voltage Capacitor
1. Check continuity of the capacitor with the meter set at the highest resistance scale.
2. Once the capacitor is charged, a normal capacitor shows continuity for a short time, and then indicates 9MW.
3. A shorted capacitor will show continuous continuity.
4. An open capacitor will show constant 9MW.
5. Resistance between each terminal and chassis should read infinite.
5-5 High Voltage Diode
1. Isolate the diode from the circuit by disconnecting its leads.
2. With the ohm-meter set at the highest resistance scale, measure across the diode terminals. Reverse the
meter leads and read the resistance. A meter with 6V, 9V or higher voltage batteries should be used to
check the front-to back resistance of the diode (otherwise an infinite resistance may be read in both
directions). The resistance of a normal diode will be infinite in one direction and several hundred KW in
the other direction.
5-6 Main Relay and Power Control Relay
1. The relays are located on the PCB Ass'y. Isolate them from the main circuit by disconnecting the leads.
2. Operate the microwave oven with a water load in the oven. Set the power level set to high.
3. Check continuity between terminals of the relays after the start pad is pressed.
5-7 Adjustment of Primary Switch, Door Sensing Switch and Monitor Switch
Precaution
For continued protection against radiation hazard, replace parts in accordance with the wiring diagram and be sure to use the
correct part number for the following switches: Primary and secondary interlock switches, and the interlock monitor switch
(replace all together). Then follow the adjustment procedures below. After repair and adjustment, be sure to check the continuity
of all interlock switches and the interlock monitor switch.
1. When mounting Primary switch and Interlock
Monitor switch to Latch Body, consult the figure.
2. No specific adjustment during installation of
Primary switch and Monitor switch to the latch
body is necessary.
3. When mounting the Latch Body to the oven
assembly, adjust the Latch Body by moving it so
that the oven door will not have any play in it.
Check for play in the door by pulling the door
assembly. Make sure that the latch keys move
smoothly after adjustment is completed.
Completely tighten the screws holding the Latch
Body to the oven assembly.
4. Reconnect to Monitor switch and check the
continuity of the monitor circuit and all latch
switches again by following the components test
procedures.
5. Confirm that the gap between the switch
housing and the switch actuator is no more than
0.5mm when door is closed.
5-2
Primary Interlock Switch
Interlock
Monitor
Switch
Lever Door(B)
Body Latch
Door Sensing
Switch
Primary switch
Monitor switch (COM-NC)
Monitor switch (COM-NO)
Door Sensing S/W
Door Open
¥
0
¥
¥
Door Closed
0
¥
0
0
Samsung Electronics
Alignment and Adjustments
5-8 Output Power of Magnetron
CAUTION
MICROWAVE RADIATION
PERSONNEL SHOULD NOT ALLOW EXPOSURE TO MICROWAVE RADIATION FROM MICROWAVE GENERATOR OR OTHER PARTS
CONDUCTING MICROWAVE ENERGY.
The output power of the magnetron can be measured by performing a water temperature rise test.
Equipment needed :
* Two 1-liter cylindrical borosilicate glass vessel (Outside diameter 190 mm)
* One glass thermometer with mercury column
NOTE: Check line voltage under load. Low voltage will lower the magnetron output. Make all temperature
and time tests with accurate equipment.
1. Fill the one liter glass vessel with water.
2. Stir water in glass vessel with thermometer, and record glass vessel's temperature ("T1", 10±1ûC).
3. After moving the water into another glass vessel, place it in the center of the cooking tray. Set the oven to high
power and operate for 49.5 seconds exactly. (3 seconds included as a holding time of magnetron oscillation:)
4. When heating is finished, stir the water again with the thermometer and measure the temperature ("T2").
5. Subtract T1 from T2. This will give you the water temperature rise. (DT)
6. The output power is obtained by the following formula;
Output Power =
4.187 x 1000 x DT
46.5
42 : Heating Time (sec)
4.187 : Coefficient for Water
1000 : Water (cc)
DT : Temperature Rise (T2-T1)
* Output (W) = 90 x DT
7. Normal temperature rise for this model is 9ûC to 11ûC at 'HIGH'.
NOTE 1: Variations or errors in the test procedure will cause a variance in the temperature rise.
Additional power test should be made if temperature rise is marginal.
NOTE 2: Output power in watts is computed by multiplying the temperature rise (step E) by a factor of 91
times the of centigrade temperature.
Samsung Electronics
5-3
Alignment and Adjustments
5-9 Procedure for Measurement of Microwave Energy Leakage
1) Pour 275±15cc of 20±5ûC(68±9ûF) water in a beaker
which is graduated to 600cc, and place the beaker in
the center of the oven.
2) Start to operate the oven and measure the leakage by
using a microwave energy survey meter.
3) Set survey meter with dual ranges to 2,450MHz.
4) When measuring the leakage, always use the 2 inch
spacer cone with the probe. Hold the probe
perpendicular to the cabinet door. Place the spacer
cone of the probe on the door and/or cabinet door
seam and move along the seam, the door viewing
window and the exhaust openings moving the
probe in a clockwise direction at a rate of 1 inch/sec. If the leakage testing of the cabinet door seam is
taken near a corner of the door, keep the probe perpendicular to the areas making sure that the probe end
at the base of the cone does not get closer than 5cm to any metal. If it gets closer than 5cm, erroneous
readings may result.
5) Measured leakage must be less than 4mW/cm2, after repair or adjustment.
Maximum allowable leakage is 5mW/cm2.
4mW/cm2 is used to allow for measurement and meter accuracy
5-10 Check for Microwave Leakage
1. Remove the outer panel.
2. Pour 275±15cc of 20±5ûC(68±9ûF) water in a beaker
which is graduated to 600cc, and place the beaker in
the center of the oven.
3. Start the oven at the highest power level.
4. Set survey meter dual ranges to 2,450MHz.
5. Using the survey meter and spacer cone as described
above, measure arnear the opening of magnetron, the
surface of the air guide and the surface of the wave
guide as shown in the following photo.( but avoid the
high voltage components.) The neading should be less
than 4mW/cm2.
5-11 Note on Measurement
1) Do not exceed the limited scale.
2) The test probe must be held on the grip of the handle, otherwise a false reading may result when the
operator's hand is between the handle and the probe.
3) When high leakage is suspected, do not move the probe horizontally along the oven surface; this may
cause damage to the probe.
4) Follow the recommendation of the manufacturer of the microwave energy survey meter.
5-12 Leakage Measuring Procedure
5-12-1 Record keeping and notification after measurement
1) After adjustment and repair of a radiarion preventing device, make a repair record for the measured
values, and keep the data.
2) If the radiation leakage is more than 4 mW/cm2 after determining that all parts are in good condition,
functioning properly and the identical parts are replaced as listed in this manual notift that fact to ;
CENTRAL SERVICE CENTER
5-12-2 At least once a year have the microwave energy survey meter checked for accuracy by its
manufacturer.
5-4
Samsung Electronics
6. Troubleshooting
PRECAUTION
1. CHECK GROUNDING BEFORE CHECKING FOR TROUBLE.
2. BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT.
3. DISCHARGE THE HIGH VOLTAGE CAPACITOR.
4. WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT ONE LEAD WIRE FROM THESE
PARTS AND THEN CHECK CONTINUITY WITHOUT THE POWER SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE
READING OR DAMAGE TO YOUR METER.
5. DO NOT TOUCH ANY PART OF THE CIRCUIT OR THE CONTROL CIRCUIT BOARD, SINCE STATIC DISCHARGE MAY DAMAGE IT.
ALWAYS TOUCH GROUND WHILE WORKING ON IT TO DISCHARGE ANY STATIC CHARGE BUILT UP.
6-1 Electrical Maltunction
SYMPTOM
CAUSE
CORRECTIONS
Oven is dead.
Fuse is OK.
No display and no operation at all.
1. Open or loose lead wire harness
2. Open thermal cutout (Magnetron)
3. Open low voltage transformer
4. Defective Ass'y PCB
Check fan motor when thermal cutout is defective.
No display and no operation at all.
Fuse is blown.
1. Shorted lead wire harness
2. Defective primary latch switch (NOTE 1)
3. Defective monitor switch (NOTE1)
4. Shorted HVCapacitor
5. Shorted HVTransformer (NOTE2)
Check adjustment of primary, interlock monitor,
power relay, door sensing switch.
Check Ass'y PCB when LVT is defective.
NOTE 1: All of these switches must be replaced at the same time.
(refer to adjustment instructions)
Check continuity of power relay contacts and if it has continuity, replace power
relay also.
NOTE 2: When HVTransformer is replaced, check diode and magnetron also.
Oven does not accept
key input (Program)
Timer starts countdown but no
microwave oscillation.
(No heat while oven lamp and
fan motor turn on.)
Samsung Electronics
1. Key input is not in-Sequence
2. Open or loose connection of membrane
key pad to Ass'y PCB
3. Shorted or open membrane panel
4. Defective Ass'y PCB
Refer to operation procedure.
1. Off-alignment of latch switches
2. Open or loose connection of high voltage
circuit especially magnetron filament
circuit
NOTE: Large contact resistance will bring
lower magnetron filament voltage and
cause magnetron to lower output and/or
intermittent oscillation.
3. Defective high voltage components
H.V.Transformer
H.V.Capacitor
H.V.Diode, H.V.Fuse
Magnetron
4. Open or loose wiring of power relay
5. Defective primary latch switch
6. Defective power relay or Ass'y PCB
Adjust door and latch switches.
Replace PCB main.
Check high voltage component according to
component test procedure and replace if it is
defective.
Replace PCB main.
6-1
Troubleshooting
6-1 Electrical Maltunction(continved)
SYMPTOM
CAUSE
CORRECTIONS
Oven lamp and fan motor turn on
1. Misadjustment or loose wiring
of primary latch switch
2. Defective primary latch switch
Adjust door and latch switches.
Oven can program but timer
does not start.
1. Open or loose wiring of secondary
interlock switch
2. Off-alignment of primary interlock
3. Defective secondary interlock S/W
Adjust door and interlock switches.
Microwave output is low;.
Oven takes longer time to
cook food.
1. Decrease in power source voltage.
2. Open or loose wiring of magnetron
filament circuit. (Intermittent oscillation))
3. Aging of magnetron
Consult electrician.
Fan motor turns on when plugged in
Loose wiring of door sensing switch
Check wire of door sensing switch.
Oven does not operate and return
to the plugged in mode.
Defective Ass'y PCB
Replace PCB main.
Loud buzzing noise can be heard.
1. Loose fan and fan motor
2. Loose screws on H.V.Transformer
3. Shorted H.V.Diode
Tighten screws of fan motor.
Tighten screws of H.V.Transformer.
Replace H.V.Diode.
Turntable motor does not rotate.
1. Open or loose wiring of turntable motor.
2. Defective turntable motor.
Replace turntable motor.
Oven stops operation during cooking
1. Open or loose wiring of primary
interlock switch
2. Operation of thermal cutout(Magnetron)
Adjust door and latch switches.
Sparks
1. Metallic ware or cooking dishes
touching on the oven wall.
2. Ceramic ware trimmed with gold or
silver powder also causes sparks.
Inform the customer.
Do not use any type of cookware with
metallic trimming.
Uneven cooking
Uneven intensity of microwave due to
its characteristics.
Wrap thinner parts of the food with
aluminum foil.
Use plastic wrap or cover with a lid.
Stir once or twice while cooking
foods such as soup, cocoa, or milk.
Noise from the turntable motor
when it starts to operate.
Noise may result from the motor.
Replace turntable motor.
6-2
Samsung Electronics
7. Exploded Views and Parts List
7-1 Exploded Views
D10
D6
D11
D5
M1
D4
D3
M3
M2
D7
D8
D9
M44
M10
M11
M4
M5
D12
D1
M42
M7
M31
D2
M32
M34
M9
M6
M8
M33
M35
M12
M13
M14 M16
M15
M30
NC
NO
COM
M17
B2
B1
M36
M43
M29
C12
C3
B4
M28
M27
C13
M20
B3
B2
M18
M41
C11
C4
M21
C5 C9
M22
M19
M23
C2
C6
C1
C7
C8
C10
M24
M4O
M25
M37
M26
M45
M38
M39
Samsung Electronics
7-1
Exploded Views and Parts List
7-2 Main Parts List
Ref. No.
Parts No.
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
M11
M12
M13
M14
M15
M16
M17
M18
M19
M20
M21
M22
M23
M24
M25
M26
M27
M28
M29
M30
M31
M32
M33
M34
M35
M36
M37
M38
M39
M40
M41
M42
M43
M44
DE70-30001A
DE63-90035G
DE61-50575A
DE47-00001A
DE60-40009B
DE63-20017A
DE61-50021A
DE61-50027B
DE61-50025A
DE39-20058K
DE97-00083A
DE39-00047A
3601-000438
DE96-00007C
DE31-00002B
DE47-20009A
DE61-50490A
OM75PH(31)ESS
DE71-60458A
4713-001031
DE93-20020A
2501-001107
DE61-50106A
DE91-70061A
DE91-70063A
DE61-40066A
DE80-10001G
DE26-00008A
DE31-10154A
DE71-00015A
DE61-30006A
DE61-70060A
DE47-00002A
DE62-20064A
DE94-00176N
DE94-00138M
DE74-20015B
DE92-90189U
DE67-60081A
DE74-70081A
DE27-10020C
DE39-40409A
DE47-00003A
DE65-20014A
: Option Parts
7-2
Description
PANEL-OUTER
CUSHION-RUBBER
BRACKET-UPPER
HEATER
WASHER-TEFLON
GASKET-HEATER
BRACKET-FLANGE
BRACKET-HEATER
BRACKET-EARTH
ASSY POWER CORD
ASSY-COVER BACK
WIRE HARNESS-A
FUSE-FERRULE
ASSY NOISE FILTER
MOTOR-FAN
THERMOSTAT
BRACKET-TCO
ASSY-MAGNETRON
COVER-AIR
LAMP-INCANDESCENT
ASSY BODY LATCH
C-OIL
BRACKET-HVC
ASSY-H.V.FUSE
ASSY-HVD
FOOT
BASE-PLATE
TRANS-H.V
MOTOR-DRIVE
COVER-CEILING
SUPPORTER-HEATER
SPRING-PLATE
THERMOSTAT
DUCT-AIR
ASSY DOOR
ASSY CONTROL-BOX
TRAY-COOKING
ASSY-GUIDE ROLLER
COUPLER
RACK-WIRE
COIL-CHOKE
WIRE HARNESS-E
THERMOSTAT
CABLE CLAMP
: Warning
Specification
Q'ty
SECC,T0.6,360,1128,EPOXY-COATI
DFA20,T2,W190,L100,BLK
SECC,T0.5,-,-,-,3RD
230V,1250W,-,-,SHG-2933E
SLOT,ID22.2,OD28,T1.2,TEFLON
BRASS,T1.5,OD30.5,ID22.5
SECC1,T0.8,32,32
SECC,T1.0,W51,L55,CE945GF
BSS2-A,T1.0,CE745G
KKP-4819D
3RD-GRILL,BACK COVER+LABEL
230V50HZ,-,-,CE2974,SEF,VDE
250V,10A,SLOW-BLOW,CERAMIC
SN-3WEG,250V15A,3W INRUSH TC
SMF-3RDEA1,-,230V50HZ,2350RPM,CE2933
PW2N-520PB,160/60,250V/7.5A,H
SECC1,T0.6,34,58
OM75PH(31)ESS
PP(TB53),78G,-,-,WHT,3RD-1.0/1.3 MW5896W
230V,173mA,40W,ORG,-,-,25x69mm
RE-43B/90B
1.1uF,2.1KV,BK,54x35x85,20mm
SECC,T0.8,W31,L125.8
THV060T-0800-H,5KV/0.8A,WHT
V2M6,PI9.0,0.05MT
PP,BLK,-,-,3RD-W
SGCC,T0.8,W345,L565,3RD
SHV-293EC,230V50HZ,2230V/3.15V,-,DY
M2HJ49ZR02,ST-16,50/60HZ
T0.3,W114.2,L121.5,-,CE2933
ALUMINA,5G,2ND-W/P
SK-5,T0.5
PW2N,-,-,100,110
SECC1-P,T0.5
CE2914R/BWT,RUSSIA/WHITE,FISH2
230V50HZ,CE2974R/BWT,WHITE,FISH2,RUSSIA
GLASS,T6.0,PI318,1050G,MW5630T
1.0CUFT(PPS)15.5
PPS,-,-,-,3RD-1.0/1.3
HSWR,PI3,W268,H110,-,MW5584W
TC-104,0.9UH*2,-,L31*W20*H32,-,ABS,AC250V/14
230V50HZ,M9G45,CTW
PW2N,-,-,-,120/110,-,-,-,187,30.0
DA-6N,NY-66
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Remarks
GRILL-TCO
CVT-TCO
P-CORD
:Electrostatically Sensitive Devices
Samsung Electronics
Exploded Views and Parts List
7-3 Door Parts List
Ref. No.
Parts No.
Description
Specification
Q'ty
D1
DE64-20112D
HANDLE-DOOR
ABS(HR0370U),30G,WHT,-,M959
1
D2
DE01-00098A
FILM-DOOR
PET,T0.13,W22.6,L201.8,-,M959
1
D3
DE64-40263F
DOOR-A
ABS(HR0370U),160G,WHT,-,M959
1
D4
DE64-40265R
DOOR-SCREEN
SAN,-,-,-,3RD-1.0,FISH2,CE2914R/BWT,RUSSIA/GRILL
1
D5
DE94-00075B
ASSY DOOR-E
3RD-1.0,BLK,COATING
1
D6
DE64-40012A
DOOR-C
RESIN-PP(TB53),T2.0,CE945GF,BL
1
D7
DE01-00118B
FILM-DOOR
T0.15,W295,L185,-,-,CE2933
1
D8
DE61-70126A
SPRING-KEY
0.8,0,36,6,BLUING
1
D9
DE64-40264C
DOOR-KEY
POM(F20-02),5g,BLK,-,2ND HANDL
1
D10
DE61-80002A
HINGE-UPPER
SCP1,T2.3,26,77,ZPC3,WHT,CE945
1
D11
DE61-80003A
HINGE-LOWER
SCP1,T2.3,26,77,ZPC3,WHT,CE945
1
D12
DE94-00173P
ASSY DOOR-A
CE2914R/BWT,WHITE/RUSSIA,FISH2
1
Remarks
7-4 Control Parts List
Ref. No.
Parts No.
Description
C1
DE67-40145A
WINDOW-DISPLAY
Specification
ACRYL,T2,W40,L77,SMOG,30G
Q'ty
1
C2
DE71-00031V
COVER-PANEL
ABS,CE2974R/BWT,-,-,WHITE,3RD-1.0,FISH2
1
C3
DE72-00006V
CONTROL-PANEL
ABS,CE2974R/BWT,-,-,-,-,WHITE,RUSSIA
1
C4
DE66-20176E
BUTTON-SELECT-C
ABS(HR0370U),5G,-,WHT,M959
1
C5
DE66-20175E
BUTTON-SELECT-B
ABS(HR0370U),5G,-,WHT,M959
1
C6
DE66-00007A
BUTTON-TRAY
ABS,-,-,WHT,10G
1
C7
DE66-00010A
BUTTON-CANCEL
ABS,-,D16.3,WHT,5G
1
C8
DE66-20182J
BUTTON-START
ABS,-,2G,P/WHT,M1774,3RD FISH2
1
C9
DE71-60378A
COVER-LAMP
POM,T2,W19.4,L27,3G,NTR,RE-446
1
C10
DE64-10127B
KNOB-COVER
ABS(HR0370U),-,WHT(W9501),-,CE
1
C11
DE64-00005A
KNOB-POWER
ABS,10G,WHT,-,M1974
1
C12
RC-F209-03
ASSY PCB PARTS:CE297
-
1
C13
DE94-00141V
ASSY CONTROL-PANEL
230V50HZ,CE2974R/BWT,WHITE,RUSSIA
1
Samsung Electronics
Remarks
7-3
Exploded Views and Parts List
7-5 Body Latch Parts List
Ref. No.
Parts No.
Description
Specification
Q'ty
B1
DE66-40021A
LATCH-BODY
POM(F20-02),50G,RE-330
1
B2
3405-000178
SWITCH-MICRO
250V,15A,200gf,SPST-NO
2
B3
3405-000175
SWITCH-MICRO
250V,15A,200gf,SPST-NO
1
B4
DE66-90054A
LEVER-SWITCH
POM(F20-02),15G,NTR,RE-330
1
Remarks
7-6 Standard Parts List
Parts No.
DE60-10012A
DE60-10012A
DE60-10013A
DE60-10018A
DE60-10024A
DE60-10045A
DE60-10069A
DE60-10069A
DE60-10072A
DE60-10080A
DE60-10080A
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10098A
DE60-10098A
DE60-10122A
DE60-20063A
DE60-20063A
DE60-10045A
DE60-10088A
DE60-10069A
DE60-10082J
DE60-10012A
7-4
Description
SCREW-TAP TITE
SCREW-TAP TITE
SCREW-ASSY TAP
SCREW-ASSY MACHINE
SCREW-PH
SCREW-TAP PH
SCREW-TAP TH
SCREW-TAP TH
SCREW-TAP TH
SCREW-WASHER
SCREW-WASHER
SCREW-A
SCREW-A
SCREW-A
SCREW-A
SCREW-ASSY TAP TITE
SCREW-ASSY TAP TITE
SCREW-TAP TH
BOLT-FLANGE
BOLT-FLANGE
SCREW-TAP PH
SCREW-TAP PH
SCREW-TAP TH
SCREW-TAPPING
SCREW-TAP TITE
Specification
TH,+,3,M4,L10,SWR10,ZPC2,TOOTH
TH,+,3,M4,L10,SWR10,ZPC2,TOOTH
TH,2S,4,L12,MSWR3,ZPC3,FIBER
PH,M4X0.7P,8,MSWR10,SN1,WS
PH,+,M4,L8,MSWR10,ZPC3
PH,M3,L6,FEFZY
TH,M4,L10,FRFZY
TH,M4,L10,FRFZY
TH,M4,L16,FEFZY,2-SLOT
M5,L12,2S
M5,L12,2S
2S-4X12,TOOTHED
2S-4X12,TOOTHED
2S-4X12,TOOTHED
2S-4X12,TOOTHED
PH,TC,M4X8,SWRCH18A,ZPC2,GLD,W
PH,TC,M4X8,SWRCH18A,ZPC2,GLD,W
TAP,TH,2-4X8,FE,FN
M4,10,ZPC3,YEL,MSWR
M4,10,ZPC3,YEL,MSWR
PH,M3,L6,FEFZY
PH,M3,L8,FEFZY,PLAIN
TH,M4,L10,FRFZY
TH,2S-4X8,MSWR3,ZPC,YEL,WS
TH,+,3,M4,L10,SWR10,ZPC2,TOOTH
Q'ty
Remarks
1
1
1
2
2
2
3
1
1
4
4
2
2
2
5
1
2
2
2
2
1
11
1
1
1
N-F-EA
P-C-EA
MO/FAN
B/EATH
B/HEAT
MG-TCO
B/UPPE
CV/AIR
CB-CMP
MGT
TNS-HV
B-PLTE
CN-BOX
LATCH
PN-OUT
CV-TCO
M/DRIV
C-CEIL
HI-LOW
HI-UPP
HVC
-
Samsung Electronics
8. P.C.B Diagrams
8-1 P.C.B Diagrams
Samsung Electronics
8-1
P.C.B Diagrams
8-2 P.C.B Parts List
No. Parts No.
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P16
P16
P17
P17
P18
P19
P20
P20
P20
P21
P22
P23
P24
P25
P26
P26
P27
P28
P29
P29
P30
P30
P31
P32
P33
P34
P35
P36
P37
P38
P39
P40
P41
P42
P43
P44
P45
P46
P47
P47
P47
P48
P49
P50
P51
P52
P52
P52
8-2
0506-000180
0703-001077
3406-001036
3501-001050
3501-001062
3501-001068
3501-001155
3601-001126
3708-001315
DE09-00049A
DE26-20146A
DE30-20016A
DE34-20071A
DE39-40723A
DE47-40024A
0401-001002
0401-001002
0401-001002
0402-001103
0402-001103
0403-000355
0501-000388
0504-001014
0504-001014
0504-001014
0504-001015
0504-001044
0601-000261
1203-000460
2001-000009
2001-000032
2001-000032
2001-000034
2001-000290
2001-000290
2001-000290
2001-000429
2001-000429
2001-000435
2001-000515
2001-000577
2001-000613
2001-000780
2001-000786
2202-000127
2202-000173
2202-000807
2401-000151
2401-000244
2401-000466
2401-000914
2401-002075
2401-002598
2801-003214
3404-001022
3404-001022
3404-001022
3711-000940
3711-004143
3711-004200
DE13-20009A
DE39-60001A
DE39-60001A
DE39-60001A
Description
TR-ARRAY
LED DISPLAY
SWITCH-ROTARY
RELAY-MINIATURE
RELAY-POWER
RELAY-POWER
RELAY-MINIATURE
FUSE-FERRULE
CONNECTOR-FPC/FC/PIC
IC-MCU
TRANS-L.V
BUZZER
SWITCH-ROTARY
WIRE HARNESS
HOLDER-FUSE
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-ZENER
TR-SMALL SIGNAL
TR-DIGITAL
TR-DIGITAL
TR-DIGITAL
TR-DIGITAL
TR-DIGITAL
LED
IC-POSI.FIXED REG.
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
CRYSTAL-UNIT
SWITCH-TACT
SWITCH-TACT
SWITCH-TACT
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
IC
WIRE-SO COPPER
WIRE-SO COPPER
WIRE-SO COPPER
Specification
2003,NPN,7,1W,DIP-16,ST,1000
GRN,4DIGIT,40SEG,45.2X22.38X22.0MM
28VDC,10MA,8PDT,20MM(BLK)
24VDC,200mW,5A,1FormA,10mS,5mS
24VDC,523.2mW,16A,1FormA,15mS
24Vdc,523mW,16A,1FormA,15mS,10
24VDC,200MW,3000MA,1FORMA,10MS,10MS
250V,1.6A,FA,CERAMIC,5X20MM
12P,2mm,STRAIGHT,SN
HD404316-E02S,CE2974R/CE2774R,4BIP,SDIP
SLV-745EN,230V,50HZ,AC17/7V
CBE2220BA,STICK
DC10V,1MA,SH,PA-1005A-003-000
DC35V,C-959G,80mm,12PIN
FH-51H,7.5A
1N4148M,100V,200mA,DO-34,TP
1N4148M,100V,200mA,DO-34,TP
1N4148M,100V,200mA,DO-34,TP
1T4,400V,1A,TS-1,TP
1T4,400V,1A,TS-1,TP
UZ5.1BSB,5.1V,4.97-5.18V,500mW
KSC815,NPN,400mW,TO-92,BK,120KSR1005,NPN,300MW,4.7K/10K,TO-92,TP
KSR1005,NPN,300MW,4.7K/10K,TO-92,TP
KSR1005,NPN,300MW,4.7K/10K,TO-92,TP
KSR2005,PNP,300MW,4.7K/10K,TO-92,TP
KRA226M,PNP,400MW,2.2K/10K,TO-92M,TP
ROUND,RED,5mm,697nm
78L05,TO-92,3P,-,PLASTIC,4.8/5
20KOHM,5%,1/8W,AA,TP,1.8X3.2MM
180OHM,5%,1/4W,AA,TP,2.4X6.4MM
180OHM,5%,1/4W,AA,TP,2.4X6.4MM
220OHM,5%,1/4W,AA,TP,2.4X6.4MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1MOHM,5%,1/8W,AA,TP,1.8X3.2MM
220OHM,5%,1/8W,AA,TP,1.8X3.2MM
2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10nF,+80-20%,25V,Y5V,TP,-,7.5
1nF,10%,50V,Y5P,TP,1.9x3.5
22nF,+80-20%,25V,Y5V,TP,3.5x19
1000uF,20%,25V,GP,TP,12.5x20,5
100uF,20%,10V,GP,TP,6.3x7,5
10uF,20%,35V,GP,TP,5x7,5
22uF,20%,16V,GP,TP,5x11,5
4.7uF,20%,50V,GP,TP,5x11,5
220uF,20%,50V,GP,TP,10x16,5
4.194304MHz,50ppm,28-AAA,12pF,
15V,20mA,130°æ40gf,6x6x5mm,SPS
15V,20mA,130°æ40gf,6x6x5mm,SPS
15V,20mA,130°æ40gf,6x6x5mm,SPS
BOX,4P,1R,2.5mm,STRAIGHT,SN
BOX,2P/3P,1R,5mm/2.5mm,STRAIGH
BOX,5P/7P,1R,2.5MM,STRAIGHT,SN
KA7533,DIP
PI0.6,SN,T,52MM,TAPING_WIRE
PI0.6,SN,T,52MM,TAPING_WIRE
PI0.6,SN,T,52MM,TAPING_WIRE
Q'ty
Remarks
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
5
5
3
5
2
1
1
4
4
1
2
5
1
1
1
5
2
2
5
5
2
5
3
1
1
2
2
1
3
2
3
4
1
1
1
2
1
1
1
3
3
2
1
1
1
1
5
5
4
IC04
LED1
ECD2
RY03
RY01
RY05
RY02,RY04
FUSE
CN04
IC01
LVT1
BUZ1
ECD1
CN05
FUSE
D06,D07,D08,D09,D10
D11,D12,D13,D14,D15
D16,D17,D18
D01,D02,D03,D04,D05
D09,D19
ZD01
TR01
TR02,TR03,TR04,TR05
TR06,TR07,TR08,TR10
TR17
TR09,TR16
TR11,TR12,TR13~TR15
LED2
IC02
R38
R27,R28,R29,R30,R31
R32,R33
R34,R40
R07,R08,R10,R15,R16
R17,R20,R21,R23,R35
R36,R37
R03,R04,R05,R12,R13
R14,R18,R19
R22
R11
R01,R02
R09,R39
R06
R24,R25,R26
C12,C13
C14,C15,C16
C08,C09,C10,C11
C02
C03
C07
C04,C06
C05
C01
XTL1
SW01,SW02,SW03
SW04,SW05,SW06
SW07,SW08
CN03
CN02
CN01
IC03
J01,J02,J03,J04,J05
J06,J07,J08,J09,J10
J11,J12,J13,J14
Samsung Electronics
9. Schematic Diagrams
9-1 Schematic Diagrams
NOTE: CIRCUIT SHOWN WITH DOOR IS OPENED POSITION.
NOTE: FOR SERVICE REPLACEMENT USE 16 GA 105ûC
THERMOPLASTIC COVERED WIRE EXCEPT
FOR HIGH VOLTAGE LEADS OR AS NOTED ON SPECIAL LEADS.
WARNING
POWER MUST BE DISCONNECTED
BEFORE SERVICING THIS APPLIANCE
MAGNETRON
HIGH VOLTAGE
DIODE
TO CHASSIS
FA
F
R
HIGH VOLTAGE CAPACITOR
RED
RED
ORG
RED
BLK
BLK
HIGH VOLTAGE
TRANSFORMER
Samsung Electronics
SYMBOL
COLOR
ORG
RED
BLK
ORANGE
RED
BLACK
8-2