PureFlow AirDog FP-150 Installation manual

#4
FP-100 & FP-150
INSTALLATION MANUAL
CUMMINS POWERED
DODGE TRUCKS
Model Year 2005 TO PRESENT
High Performance Fuel System
For the 5.9L & 6.7L Engines
With New Quick Connect Components!
PLEASE READ THE INSTRUCTIONS THOROUGHLY
BEFORE BEGINNING INSTALLATION
PureFlow AirDog
705 MAUSOLEUM ROAD
SHELBYVILLE, IN 46176
1-877-421-3187
www.pureflowairdog.com
CANADIAN PATENT
2,108,391
PROTECTED BY
US PATENTS
5,355,860; 5,746,184; 6,729,310
AUSTRALIAN PATENT
2005101054
NEW ZEALAND PATENT
532356
Additional Foreign Patents Pending in Europe, South America, Mexico, Japan, and China!
Approved for Sale and Use in California by CARB!
SMALL and COMPACT
7” Long X 3.2” Wide X 10” Tall
2
OVERVIEW
Welcome to PureFlow® AirDog®
Fuel Air Separation, Filtration and Delivery System for the Diesel
Engine!
The AirDog® Fuel Air Separation system is a Premium lift pump and filtration
system for the Dodge Cummins diesel engine. A complete installation kit is
included.
The AirDog® delivers clean fuel to the engine free of virtually all air/vapor and
at a positive flow. Thus, allowing the engine “test cell” performance and
efficiency, while in “real world” use.
The AirDog® FP-100 is recommended for stock and slightly modified 5.9 L &
6.7L Cummins Diesels.
The AirDog® FP-150 is recommended for highly modified 5.9L & 6.7L
Cummins Diesels.
PureFlow products are manufactured with a personal touch,
unsurpassed attention to detail and
the most stringent quality control!
TYPICAL INSTALLATION LAYOUT
Figure 1
®
The AirDog draws fuel from the fuel tank at a constant flow, removing water, particulates,
and air/vapor. A regulated pressurized flow is maintained to meet the engine’s varying fuel
demands. The separated air/vapor is returned by the AirDog® to the fuel tank.
NOTE: The pictures used in this manual are for example only and may not be exactly the
same as your truck.
3
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005-Present
QUICK CONNECT COMPONENT OVERVIEW
Provided in this kit is an OE style Quick Connect System. This system works
to allow for a quick, clean, and professional install.
SAE J2044 Quick Connect System
The SAE J2044 quick connect system is the most commonly used system in the
automotive industry. The images below show the formation of SAE J2044
connection. To connect the assemblies, simply insert the male end form into
the mating female connector. Push firmly until you hear it “click” into place.
To disconnect the fittings, press down and hold the blue tabs on the female
connector while you firmly pull the assembly apart.
4
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - Present
Table of Contents
Section 1
TABLE OF CONTENTS
Section 1………………………............…………………..Table of Contents
Section 2…………………………….......…Installation & Safety Guidelines
Section 3………………………………….……...........…………….Parts List
INSTALLATION PROCEDURES
Section 4…………………….………………..AirDog® & Mounting Brackets
FUEL LINES
Section 5 A…………………………….……………….AirDog® To 5.9 CP-3
Section 5 B………………………....………..............AirDog® To 6.7L CP-3
Section 5 C…………………...………….………………Fuel Return to Tank
Section 5 D…………………….……..In-Tank Pump Bypass Suction Tube
Section 5 E……….…………..………………………..…In-Tank Fuel Pump
ELECTRICAL HARNESS
Section 6…..………………….………………………….Electrical Harness
Section 7..………….…….…………….……..…..Initial Startup Procedures
MAINTENANCE
Section 8………….…………...…….……Filter Service Recommendations
Section 9……………………..…………..….Pressure Regulator Changes
Section 10…………………..……………...Cleaning the Gerotor Assembly
5
PureFlow AirDog
®
AirDog FP-100 & FP-150
Section 2
Dodge 2005 - Present
Installation & Safety Guidelines
AirDog®
MODEL FP-100 & FP-150
The installation of your AirDog® can be made relatively easy by following the steps outlined
in this manual, and:
1. Inventory the package components completely. Notify PUREFLOW®AIRDOG
immediately of any parts missing or damaged.
2. Read the installation manual completely. Understand how the system operates and
installation recommendations before beginning installation.
3. The installation recommendations contained herein are suggested installation guidelines
only. Individual installations may vary.
4. If any installation procedure is uncertain, contact PUREFLOW® AIRDOG for technical
assistance.
5. When installing the AirDog® fuel lines be sure to keep the ORIGINAL ENGINE
RETURN LINE connected as it is from the factory!
SAFETY GUIDELINES!
CAUTION! Please be sure to chock the vehicle’s tires to prevent rolling.
CAUTION! Please use proper supports when working beneath an elevated vehicle.
CAUTION! Most diesel pickups have two (2) 12volt batteries. Disconnect the battery
cables to both batteries before proceeding with the AirDog® installation.
CAUTION! Vehicle frame rails should not be drilled into or welded upon.
CAUTION! Wear safety glasses when operating power tools such as drills and grinders or
when using a punch or chisel.
CAUTION! Use common sense when routing fuel lines and electrical harnesses. Keep
them away from hot exhaust components and/or moving parts. Properly
secure lines to prevent chaffing.
Use Good Judgment and Common Sense When Installing the AirDog®!
6
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - Present
Parts List
Section 3
AirDog® Parts List
QTY
1
DESCRIPTION
Part Number
Installation Manual
201-1-0105
FP-100
Or
FP-150
®
1
AirDog
1
AirDog® Mounting Bracket
001-3C-0004
Mounting Hardware Kit,
1
901-61-0102-PM
1
Frame Bracket
010-3C-0002PC
010-3C-0001PC
1
Wiring Harness
5E-2-014
1
Return Fuel Filler Tube (with 2 Clamps)
001-4A-0150
1
Bundle of Plastic Ties
5H-2-1-06/12
1
High Flow Suction Tube
1
Grommet
1
Spacer
1
Suction Hose Assembly
WAP110-8-8
1
Return Hose Assembly
WAP110-8-8-90
1
Pressure Hose Assembly
WAP110-8-8-90
1
12mm X ½” male SAE J2044 Fitting
WAP102
1
Seal Washer (Assembles on WAP 102)
1P-5-DS
1
Customer Service Oring Replacement Kit
WAP108
5J-1-1-04-0001
010-3C-0003-A-P
901-05-0101
7
IMAGE
3
Push Lock Hose Splice
001-4A-1-0026
2
1/2” Male SAE J2004 Quick Connect x 3/8” NPTF
08J2044-3/8 NPTF
ILLUSTRATION OF QUICK CONNECT COMPONENTS
8
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005- Present
AirDog & Mounting Brackets
®
Section 4
Installing the AirDog® & Mounting Brackets on the
Truck’s Frame!
Figure 2
4-1.
Figure 3
Assemble the AirDog® mounting bracket to the frame bracket.
Figure 4
4-2.
Figure 5
Use the spacer block as necessary to clear lines and wiring harnesses on the frame.
Adjust the assembly up or down on the frame bracket as necessary for clearance.
FUEL IN
4-3.
ENGINE
Install a 1/2” J2004 x 3/8” NPTF male
quick connect (08J2044-3/8 NPTF) into
the “ENGINE” and “FUEL IN” ports in
the AirDog®.
Figure 6
WARNING: The NPT fitting threads must be lubricated with oil or anti-seize compound
before installation to prevent galling!
4-4.
Attach the AirDog® to the frame bracket assembly.
Figure 7
9
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - Present
AirDog & Mounting Brackets
®
Section 4
Installing the AirDog® & Mounting Brackets on the Truck’s
Frame, cont’d!
NOTE: The AirDog® can be mounted on either the inside or the outside of the frame, as
space or personal choice dictates.
Mount
The AirDog®
Outside
The
Frame
OR
Figure 8
Figure 9
Inside
The
Frame
Figure 10
Figure 11
For this installation, the AirDog® is mounted inside the frame!
4-5.
Clamp the frame between the AirDog® bracket assembly and the backing plate using
the bolts, lock washers, and nuts included in the kit.
Figure 12
®
4-6. Position the AirDog on the frame as necessary for clearance.
NOTE: Be sure to mount the AirDog® so the ‘FUEL IN’ port is directed
the rear of the vehicle.
toward
Figure 13A
Figure 13B
NOTE: Some pickup model frame rails have a bracket that is used to support the frame
during the manufacturing process If this bracket is on your frame rail and obstructs the
proper positioning of the AirDog® mounting bracket, you may remove part or all of it, as
needed. Be very careful not to damage the frame flange!
10
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - 2009
Fuel Lines
Section 5-A
Fuel Supply Line from the AirDog® to the CP-3
For the 5.9L Cummins Engine
The AirDog® fuel filter has a 2 micron media. When installing the AirDog® fuel system
it is recommended to bypass the factory filter canister.
5A-1. Remove the “banjo bolt” and the original factory fuel supply line at the fuel inlet port
of the CP-3 injector pump (Ref. Figure 14).
.
Figure 14
Figure 15
5A-2. Install the 12mm x ½” male SAE J2044 (WAP 102) fitting with the seal washer
supplied into the inlet port of the CP-3 (Ref. Figure 15) vacated by the original banjo
fitting. Do not over tighten the fitting. It may crack or break.
5A-3 Insert the female quick connect end (see figure 16) of the “pressure hose assembly”
into the male quick connect fitting previously installed in the port marked
“ENGINE”. You will hear a “click” when it connects.
Figure 16
5A-4. Connect the other end of the “pressure hose assembly” to the inlet fitting installed in
step 5A-2. It will “click” when properly connected.
5A-5 Any excess fuel hose can be addressed by routing the hose in a fashion to take up the
extra length, or a section of the hose can be removed. Push lock splices have been
included if you choose to remove the excess hose.
11
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - Present
Fuel Lines
Section 5-A
5A-6. It is advised to remove the factory supply lines between the tank and the filter
canister. Also remove the factory supply line between the filter canister and the
injection pump. Then plug the ports on the filter canister. This will prevent fuel
spillage.
Figure 17
NOTE: Be sure to keep the ORIGINAL ENGINE RETURN LINE connected as it is from
the factory! In many cases the return runs thru the flange of the filter canister.
Section 5 B
Fuel Supply Line from the AirDog® to the CP-3
For the 6.7L Cummins Engine
The AirDog® fuel filter has a 2 micron media. When installing the AirDog® fuel system
it is recommended to bypass the factory filter canister.
5B-1. Remove the Quick Connect fitting and the
original factory fuel supply line at the fuel
inlet port of the CP-3 high pressure pump.
Figure 18
5B-2. Install the WAP 102 fitting with the
Seal washer supplied into the inlet port of the
CP-3 vacated by the original Quick Connect
fitting. Firmly tighten the WAP 102 fitting.
Figure 19
CAUTION: Do not over torque the WAP 102 fitting, IT
12
COULD BREAK!
PureFlow AirDog
®
AirDog FP-100 & FP-150
Section 5-B
Dodge 2005 - Present
cont’d
5B-3. Insert the female quick connect end (see figure 20) of the “pressure hose assembly”
into the male quick connect fitting previously installed in the port marked
“ENGINE”. You will hear a “click” when it connects.
Figure 20
5B-4. Connect the other end of the “pressure hose assembly” to the inlet fitting installed in
step 5B-2. It too will “click” when properly connected
5A-5 Any excess fuel hose can be addressed by routing the hose in a fashion to take up the
extra length, or a section of the hose can be removed. Push lock splices have been
included if you choose to remove the excess hose.
5A-6. It is advised to remove the factory supply lines between the tank and the filter
canister. Also remove the factory supply line between the filter canister and the
injection pump. Then plug the ports on the filter canister. This will prevent fuel
spillage.
Figure 21
NOTE: Be sure to keep the ORIGINAL ENGINE RETURN LINE connected as it is from
the factory! In many cases the return runs thru the flange of the filter canister.
13
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005- Present
Fuel Lines
Section 5-C
Fuel Return Line from the AirDog® to the Tank
Installing the fuel 'Return to Tank' assembly in Filler Tube
Filler
Tube
Fuel
Return
Fitting
Hose Clamp
Fuel Tank
Figure 22
5C-1. Cut filler tube as illustrated, removing ½ inches. Loose assemble clamps on each end
of filler tube.
Figure 23
Figure 24
5C-2. Insert “Return Fuel Filler Tube” assembly in filler tube. INSTALL THE FILLER
TUBE WITH ARROWS POINTING TOWARD THE TANK!! SEE FIG 23
Properly tighten clamps.
5C-3.
Insert the SAE J2044 female quick connect end (see Figure 24) of the “Return Hose
Assembly” into the pre-installed male quick connect fitting in the port marked
“Tank”. The fitting will “click” when properly installed
5C-4
Attach the other end of the “Return Hose Assembly” onto the male end form of the
“Return Fuel Filler Tube” installed in step 5C-2. A ”click” will be heard when the
fitting is properly connected.
5C-5
Any excess fuel hose can be addressed by routing the hose in a fashion to take up
the extra length, or a section of the hose can be removed. Push lock splices have
been included if you choose to remove the excess hose.
14
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005- Present
Fuel Lines
Section 5-D
INSTALLING THE IN-TANK FUEL PUMP BYPASS
SUCTION TUBE!
NOTE: The AirDog® installation kit includes a Suction Tube to by pass the
“in-tank fuel pump on the 2005 - Present Dodge.
To install the suction tube it is necessary to either drop the fuel tank or to lift the truck bed.
NOTE: Should you choose to drop the fuel tank, support the tank as it is when it is installed
on the truck. If you let it rest flat on the floor, the tank may squash out and the suction tube
will be too short after the tank is re-installed in the truck. The suction tube, being cut too
short may suck air as the fuel drops below ¼ tank level.
NOTE: Should you choose to pull the pickup bed to access the tank. Be sure to disconnect
the tail light wires, fuel tank filler tube, and any other accessories or components that may be
secured to the frame and bed.
When Dropping the Tank, Always Remember Safety First!
Figure 25
Figure 36
Figure 27
If you choose to remove the bed, properly support the truck bed to prevent
serious injury or death!
Figure 28
Figure 29
15
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005- Present
High Flow Suction Tube
Section 5-D
INSTALLING THE HIGH FLOW SUCTION TUBE, Cont’d
NOTE: The fuel tank used for the pictures is an example only and may not be exactly the
same as your tank.
IMPORTANT: Select a location for the suction tube that has adequate clearance
below the bed. Also consider that under hard acceleration, fuel will migrate
toward the back of the fuel tank.
5D-1. Remove the collection basket.
Figure 30
Figure 31
5D-2. Drill a 1-1/8” hole at the selected location in the fuel tank for the suction tube. Hold
a container below the drill point to catch debris.
Figure 32
Figure 33
5D-3. Remove all burrs from the edge of the hole.
Figure 34
Figure 35
5D-4. Install the grommet in the new suction tube access hole.
16
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005-Present
High Flow Suction Tube
Section 5-D
INSTALLING THE HIGH FLOW SUCTION TUBE, Cont’d
5D-5. Measure and cut the suction tube to a length that will allow approximately 1/8”
clearance off the bottom of the tank. It is suggested to form the end of the tube similar
to Figure 36.
Figure 36
5D-6. Lubricate the bulkhead fitting with motor oil. Pressing firmly, insert the suction tube
assembly into the grommet. Be sure the bulkhead fitting is completely seated in the
grommet.
Figure 37
Figure 38
5D-8. Re-install the Collection basket.
Re-install the factory return line to the proper
Port of the Collection basket before the tank
Is fully re-installed.
Figure 39
5D-9. Connect the end of the “Suction Hose Assembly” to the bulk head fitting while it is
easily accessible. A “click” will be heard when it is properly installed.
5D-10. Insert the female quick connect end (see figure 40) of the “Suction Hose Assembly”
to the male quick connect fitting in the “Fuel In” port during step 4-3 of this manual.
A “click” will be heard when the fitting is properly connected.
17
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005-Present
High Flow Suction Tube
Section 5-D
INSTALLING THE HIGH FLOW SUCTION TUBE, Cont’d
Figure 40
5D-11 Any excess fuel hose can be addressed by routing the hose in a fashion to take up
the extra length, or a section of the hose can be removed. Push lock splices have
been included if you choose to remove the excess hose
5D-12 If the fuel tank was dropped to install the suction tube, re-install the fuel tank.
If the truck bed was removed, reinstall the bed.
18
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - Present
Electrical Harness
Section 6
The AirDog® wiring harness features water proof Deutsch connectors,
relay, and fuse holder. When properly installed, the AirDog® is controlled
by the engine’s ECM.
WIRING DIAGRAM (In Red)
Figure 41
®
The AirDog is activated by the ECM through a relay controlled wiring harness connecting
directly to the original ECM Deutsch pump connector.
Power Supply Red +
Power Supply Black Pressure Sensor Lead
Motor Power Supply Lead
Low Fuel Pressure
Indicator Light Leads
Female Power Lead Jumper
Plugs into Fuel Module
Male Power Lead Jumper
Plugs into Factory Harness
Figure 42
CAUTION: If the OPTIONAL Low Pressure Indicator Light is not used, be sure to insulate
the two (2) #10 Indicator Light connectors to prevent accidental contact.
19
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - Present
Electrical Harness
Section 6
Securing the Relay and Fuse Holder to the Vehicle
6-1.
Secure the relay and fuse holder to the vehicle.
Figure 43
Figure 44
Connecting the AirDog® Power Lead Jumpers
6-2.
Remove the factory wire harness connection from the top of the fuel module as seen
in (Figure 45)
Figure 45
6-3.
Plug the AirDog female power lead jumper into the top of the fuel module.
6-4
After a “click” is heard, slide the red locking clip over to lock the connection in place.
6-5.
Plug the factory wire harness connector into the AirDog male power lead jumper.
Again, listen for the “click”.
NOTE: The power supply leads can be connected to the battery or the alternator. Connecting
the power supply leads to the alternator instead of the battery will create a corrosion free
connection.
Black (-)
Red (+)
6-6.
Route the Red & Black power supply
leads to the alternator. Connect the
Black (-) lead to the alternator
Chassis Ground connection. Connect
the Red (+) lead to the alternator Hot
Lead going to the battery.
Figure 49
20
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - Present
Electrical Harness, cont’d
Section 6
OR
6-7.
Should you choose to connect the power
supply leads directly to the battery, connect
the RED (+) lead to the POSITIVE (+) post
of the driver's side battery. Connect the
BLACK (-) lead to the NEGATIVE (-) post
of the same battery.
Figure 50
Connecting the Wiring Harness to the AirDog®
6-8
Route the wiring harness to the AirDog®
and connect the 2 pin Deutsch connector
to the corresponding connector on
the AirDog®.
Figure 51
21
PureFlow AirDog
®
AirDog FP-100 & FP-150
Section 7
Dodge 2005 - Present
Initial Startup Procedures cont’d
INITIAL START PROCEDURE
The AirDog® is a self priming system, however, to prevent potential damage to the system, it
is recommended to fill only the pre-filter with diesel fuel before initial startup.
7-1.
Fill the pre-filter with diesel fuel.
7-2.
Turn the starter key to the on/run position.
NOTE: It may be necessary to momentarily engage the starter in order for the ECM
to energize the AirDog®.
7-3.
While the AirDog® is operating, bleed the air from the fuel line to the engine by
loosening the fuel line connection at the engine fitting. As soon as the line is purged
of air and pure fuel is observed, properly tighten the fuel fitting. NOTE: put a rag or
shop towel over and around fitting to prevent splatter. Catch all spilled fuel and
dispose of properly.
7-4.
Start the engine!
RECHECK ALL FUEL FITTINGS FOR LEAKAGE AND PROPERLY TORQUE.
BE SURE ALL FUEL LINES ARE PROPERLY ROUTED TO PROTECT FROM
EXCESSIVE HEAT AND SECURED TO PROTECT FROM CHAFFING AND
ABRASION. RECHECK ALL ELECTRICAL LINES, SECURE AS NECESSARY.
Checking Pump Noise!
NOTE: Each AirDog® has been manufactured in a Quality Controlled process and fully
tested for operation and performance before shipment. This is a very quiet and smooth
running system. However, if any fuel fitting on the vacuum side, between the fuel tank and
the AirDog® or the pre-filter, has been left loose during the installation process, the system
may suck air at an excessive rate and will be very noisy. To check for this problem, unscrew
the pre-filter 3 or 4 full turns and activate the AirDog® by turning the ignition switch to on. If
the AirDog® runs quietly, then excessive air from a loose fitting or leaking water separator
seal is most likely the reason for the excessive noise. Correct as necessary.
A.
The seal groove in the 3” filter is a snug fit and on occasion the seal has been found
to not be fully seated. Remove the pre-filter, remove the seal from the top of the nut
plate. Clean and lubricate the seal groove. Carefully replace the seal in the groove. Be
sure to fully seat the seal.
B.
Check all fittings, especially the connection at the tank.
22
PureFlow AirDog
®
AirDog FP-100 & FP-150
Dodge 2005 - Present
Fuel Filter & Water Separator Cont’d
Fuel Filter & Pre-Filter
Section 8
Filter Service Recommendations
Plugging of either the fuel filter or the water separator itself will cause low fuel pressure and
low flow to the engine. If a low fuel pressure issue exists, replace the fuel filter.
AirDog®
2 Micron Fuel Filter
AirDog®
WATER
SEPARATOR
Drain Valve
The Water Separator
Replace the water separator every other time you change the Fuel Filter or if it becomes
damaged or plugged. It is suggested to check/drain the water separator every three months or
as needed should you experience excessive ‘water in fuel’ conditions. When installing the
water separator, be sure to clean the underside of the AirDog® base. Follow the instructions
printed on the water separator for proper tightening procedures.
CAUTION: Be extremely careful to prevent any contaminates or debris from entering the
pre-filter when removing it for cleaning! Large debris will jam the Gerotor and cause the fuse
to blow. This is not a warranty item. Should this happen, you can easily put the system back
into working order. See the instructions on “How to clean the Gerotor” for proper
procedures.
The Fuel Filter
Remove the fuel filter by turning it counter clockwise. Do Not pre-fill the fuel filter with
fuel. The AirDog® will fill the filter and prime the system automatically. Follow the
instructions on the filter for proper tightening procedures.
CAUTION: Dispose of waste fuel and used filters properly to protect OUR environment!
23
PureFlow AirDog
AirDog FP-100 & FP-150
Dodge 2005 - Present
Pressure Regulator Upgrade
Section 9
Changing the Regulator Spring
The AirDog® is shipped from the factory with the fuel pressure preset.
For the 2005-2009 Dodge Cummins the AirDog® fuel outlet pressure is preset at 15 PSI
(±2). However, for some applications, you may desire to increase the pressure output from
your AirDog®. To do this, you will need to purchase and install a higher tension spring.
Regulator Spring Replacement Procedure
The regulator spring and ball assembly is located inside the Return to
Tank fuel port.
Step-1. Disconnect the ‘Return to Tank’ fuel line.
Figure 9-1
Figure 9-2
Figure 9-3
Step-2. Remove the ‘Return to Tank’ fuel line fitting exposing the regulator spring.
Step-3. Remove the ball and spring.
Figure 9-4
Figure 9-5
PureFlow
Figure 9-6
Step-4. Install the new regulator spring by reversing the steps shown in Figures 9-1 through
9-6. Be sure to place the regulator ball in the regulator seat before inserting the
spring. Properly torque the return line fitting and swivel connection when finishing.
24
Section 10
Cleaning Foreign Debris from the Gerotor Assembly
Step 1
Remove the four (4) socket
head cap crews that secure
the Gerotor cap.
Step 4
Clean the inside of the
Gerotor pocket.
Step 2
Step 3
Carefully remove the O-ring, Remove and clean the Gerotor.
you will need to re-use it.
Be very careful not to damage
the Gerotor.
Step 5
Replace the O-ring and
center gear.
Step 7
Install the Gerotor cap. Be very
careful to index the cap to position
the wide space between the half
moon cuts to the bottom.
Step 6
Align the teeth and
install the outer gear.
Step 8
Replace the cap into
position. Be very careful,
do not pinch the O-ring.
Torque the cap screws.
in an opposing pattern.
25
1.
4.
3.
2.
Installing a New Filter
1. Clean the area around the filter head and groove or seal area.
NOTE: Lubricate the seal with oil. Do not use diesel fuel to lubricate the seal.
2. Install a new fuel filter on the filter head. Turn clock-wise until the filter contacts the seal.
Tighten the filter one full turn or follow tightening instructions on filter after contact with
the seal has been made.
NOTE: It is not necessary to pre-fill the fuel filter!
CAUTION: DO NOT OVER TIGHTEN, OVER TIGHTENING CAN DISTORT
THREADS OR DAMAGE THE FILTER SEAL.
3. To prime the filter, turn the ignition switch to the on position. Start the engine.
Water Separator
With the engine turned off, pinch off the suction line. Open valve on the bottom of the water
separator. Drain into a suitable container until all water has been removed. Close valve.
Remove the pinch in the suction.
DRAINING: The water separator should be serviced once a month or when severe water in
fuel conditions require.
NOTE: Collect all spilled fuel and dispose of in accordance with federal, state and local
regulations.
26
PUREFLOW AIRDOG
LIFETIME LIMITED EXPRESS WARRANTY
FOR
Cover PureFlow AirDog I, II and Raptor Systems
IMPORTANT NOTICE
TO ACTIVATE YOUR PURFLOW AIRDOG WARRANTY, YOU MUST COMPLETE AND
MAIL YOUR WARRANTY CARD TO PUREFLOW AIRDOG WITH A COPY OF YOUR
ORIGINAL SALES RECEIPT WITHIN 30 DAYS OF PURCHASE. FAILURE TO
COMPLETE AND SUBMIT YOUR WARRANTY CARD WILL RESULT IN A WARRANTY
PERIOD OF THE COVERED PRODUCE TO ONE (1) YEAR FROM THE DATE OF
PURCHASE.
PureFlow AirDog (hereafter collectively, “SELLER”) warrants and guarantees only to the Original Purchaser
(hereafter collectively, BUYER) that All PureFlow AirDog Systems (hereafter collectively, PRODUCT) shall
be free from defects of materials and workmanship in the manufacturing process for as long as the BUYER
owns the PRODUCT.
The Lifetime Limited Express Warranty is limited to the PRODUCT purchased by the original BUYER of the
PRODUCT and limited solely to the parts contained within the PRODUCT and EXCLUDES ALL ELSE
INCLUDING FILTERS AND WATER SEPARATORS. Any PRODUCT that is in question of Warranty must
be returned, shipped prepaid, to PureFlow AirDog. All Warranty claims are subject to the approval of
PureFlow AirDog. If it is determined that a Warranty claim exists, PureFlow AirDog will, at its sole discretion,
replace the defective PRODUCT with a comparable PRODUCT, repair the defective PRODUCT, or refund the
BUYER”S purchase price in exchange for the PRODUCT. Repairs or replacements are warranted for only the
remainder of the original warranty period and only to the original BUYER.
Under no circumstances shall the SELLER be liable for any labor charged or travel time incurred in the
diagnosis for defects, removal, or reinstallation of the PRODUCT, or any contingent expense.
Under no circumstances will the SELLER be liable for any damage or expense incurred by reason of the use or
sale of the PRODUCT.
Other than expressly set forth herein, the SELLER shall in no way be responsible for the proper or improper use
and service of the PRODUCT. In no event shall the SELLER be liable for any special, incidental, indirect or
consequential damages of any kind or nature, whether or not the BUYER of the PRODUCT was advised of the
possibility of damage or harm, arising or resulting from the use or performance of the PRODUCT and BUYER
hereby waives the right to any and all such claims.
BUYER, acknowledges that he/she is not relying on SELLER’S skill or judgment to select or furnish goods
suitable for any particular purpose and that SELLER has no liability that will extend beyond the scope of the
LIMITED EXPRESS WARRANTY contained herein, and BUYER hereby waives all remedies or liabilities,
expressed or implied, arising by operation of law or otherwise.(including, without limitation, any obligation of
SELLER with respect to fitness for any particular purpose; merchantability; and special, incidental, indirect or
consequential damages) or whether or not occasioned by SELLER’S negligence.
SELLER disclaims any warranty and expressly disclaims any liability for personal inquiry or damages related
to BUYER’S use of the PRODUCT. BUYER acknowledges and agrees that the disclaimer of any liability for
personal injury is a material term for this agreement and BUYER agrees to indemnify SELLER and hold
SELLER harmless from any claim related to the PRODUCT and its use or performance. Under no
circumstances will SELLER be liable for any damages, liabilities, costs or expenses incurred as a result of or by
reason of use, performance or sale of the PRODUCT, including without limitation, any damages, liabilities,
costs or expenses incurred by reason of BUYER’S negligence related to those uses of the PRODUCT.
The proper installation of the PRODUCT is the sole responsibility of the BUYER. The SELLER assumes no
liability regarding improper installation or misapplication of the PRODUCT.
27
SELLER hereby provides the following limited warranty as to description, quality, merchantability, fitness for
the PRODUCT’S purpose, productiveness, or any other matter of SELLER’S PRODUCT sold herewith. The
SELLER shall be in no way responsible for the open use and service of the PRODUCT and the BUYER hereby
waives all rights other than those expressly written herein. This Warranty shall not be extended or varied
except by a written instrument signed by SELLER and BUYER.
IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS AGREEMENT, THE BUYER MAY
PROMPTLY RETURN THE PRODUCT, IN A NEW AND UNUSED CONDITION, WITH A DATED
PROOF OF PURCHASE, TO THE PLACE OF PURCHASE WITHIN THIRTY (30) DAYS FROM THE
DATE OF PURCHASE FOR A FULL REFUND. THE BUYER AGREES THAT THE INSTALLATION OF
THIS PRODUCT CONFIRMS THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND
ACCEPTS THE TERMS AND CONDITIONS OF THIS AGREEMENT.
Warranty Procedure
In the unlikely event a warranty appears as if it may be warranted, the following steps are taken:
1 The customer discussed the symptoms of the problem with a PureFlow AirDog Technician. The
customer is to have the system Serial Number and Model Number available for the Technician
when the call is made. This will expedite all steps of the process.
2 The customer performs any and all tests requested by the PureFlow AirDog Technician. This is done
to isolate the potential problem while eliminating potential installation or maintenance related
issues,
3 If the PureFlow AirDog Technician determines based on the customer feedback concerning the
requested testing that system may be at fault, the customer is advised that all returned pumps
are tested upon arrival and should this returned pump perform at design criteria upon arrival,
the customer will be charged a $50.00 fee.
4 The PureFlow AirDog Technician will first request the customer’s phone number in the event the
phone call is accidentally disconnected and then transfer the customer to a PureFlow AirDog
Customer Service Representative. Should a Customer Service Representative not be available,
the Technician will offer the Customer the option to hold, call back, or receive a return call.
5 The PureFlow AirDog Customer Service Representative will check to determine if the customer’s
Warranty Registration Card is on file.
a. If no Warranty Registration is found, the customer will be required to supply the original
purchase receipt showing the purchase date.
b. If no Warranty Registration is found, the customer will be advised of the options should the
system in question is out of the default warranty period (1 year).
6 The PureFlow AirDog Customer Service Representative will request the customer information,
including: Name, Address, Phone Number, Model Number, Serial Number, Year / Make / Model
of vehicle, Name of Dealer purchased from, Purchase Date, Description of Problem, Customers’
understanding of the resolution, and customer credit card information.
7 PureFlow AirDog will cover Ground Shipping charges to ship the replacement unit and will include a
prepaid shipping label for the return of the defective unit. Any additional items ordered at the
time of the replacement shipment will include their portion of the shipping cost.
8 A period of 15 Calendar Days from the time of shipment is provided for the receipt of the defective
unit at the PureFlow AirDog facility. Failure to return ship the defective unit to arrive within the
defined time period will result in a charge of $250.00 against the customer’s credit card as the
purchase cost of the defective unit.
PFT Bulletin No. 201-1-0105
Revised July 24, 2014
28