Rcom PRO 20 User`s manual

New Rcom 20 USER'S MANUAL
PX-20(Standard)
Digital Incubator
5. How to Replace Fuse
4. How to Assemble
www.R-com.co.kr
1. Safety Cautions
▶ When the machine failed to
power on even if you pluged in,
remove the fixing piece like
the picture by screwdriver.
View Window
Electrical hazards
Ver E 1.0.0
Be careful the details below when you use.
REA
R
Insert the power cord
in the socket at the back
of the main body.
Universal Tray
Main Body-1
RE
AR
AUTOELEX
AUTOELEX
▶ You can find assembled PCB
when open the cover.
Remove faulty fuse with screwdriver.
Egg turning Plate
Risk of electric shock or fire.
Do not pull the cord when
taking out the power cord,
and keep wet hands away
from connecting plug.
Risk of electric shock or fire.
Never pull the plug out of
the outlet during the
incubation period.
Do not twist or crush
electric cord.
Incubation will be interrupted.
Risk of electric shock or fire.
Setting Cautions
Do not insert multiple
connecting plugs in an
outlet.
FRON
T
Do not use a damaged
power cord or loose
outlet.
Lock the three locking
buttons at the front and rear
of the incubator.
Main Body-2
▶ Replace with new fuse.
( 250V 2.0A Ø5*20mm )
Risk of fire or electrical overload.
Be careful the details below when you use.
6. Before use
▶ Insert the electric cord in the connecting socket at the back of the Main body and
put the power cord into the outlet. The display will come on.
Do not install in dusty or
dirty environment.
Risk of damage or fire within
the incubator.
Do not install under the
direct sunlight.
Risk of fire or interference with
the incubation process.
Do not install in excessively
cold or hot conditions,
cigarette smoke, etc.
Risk of interference with
the incubation process.
Do not install in moist or
humid environment.
Risk of fire or electric shock.
Do not use any other
non-standard parts
except those provided.
Risk of damage or hatching
failure.
There can be some odor the first time you use the incubator, that is normal.
▶ Open the watercap and fill the hole with clean water. And, refill water after 5 min.
The styrofoam ball floats on and blocks the hole when full.
(Humidity goes down temporarily, in case you refill water under incubation period.)
You should stop to fill in the water as soon as the Styrofoam ball floats on.
The ball will block the hole when full.
After filling up with water, never shake or turn over the main body of the incubator.
Do not cover the
ventilating opening.
Inner temperature can rise,
interrupting incubation.
Install away from heat
sources.
Risk of damage to the incubator
case and interference with
the incubation process.
Ensure that the incubator is
installed on a stable surface
away from edges.
Risk of damage to incubator
and eggs and user from
accidental knocks or drops.
Do not turn the incubator
upside down.
Water will pour out of the incubator,
and view window can be dropped
or damaged.
Do not install where
children or other people
can touch with easy.
Risk of knocking the incubator
or accidental interference with
the controls.
Check the water level every three days and refill fully on incubation period.
The light for water top-up can remain for a while after you filled up.
▶ Place your eggs and cover the view window.
R
WATE
Be careful to close the view window completely; if not, the temperature will fail
to go up. (It will cause alarm.)
The egg to incubate must be a fertilized egg.
Do not disassemble or
modify the incubator in
any way.
Risk if electric shock or fire.
Please ensure that no
small objects get into
the holes on the incubator.
Risk of electric shock or fire.
If the incubator sounds
strange or emits smoke
contact your service
center.
Risk of electric shock or fire.
Clean the incubator
thoroughly before storing.
If the incubator requires
repair disconnect from the
power supply and please
contact to your service center.
Be sure to disconnect the electric cord
from the outlet before cleaning.
Cleaning Cautions
You can turn off humidification function when you don't fill water with your incubation
or when you need low humidity incubaion under 40%.
(Water supplement alarm will turn off with this function.
Refer to "How to turn OFF humidification function.")
R
WATE
7. Operation Part
Do not spray cleanser
directly on the incubator
surface.
Clean the incubator by a
soft cloth with a neutral
detergent.
Brush away dust on the
plug with a dry cloth.
Do not use chemicals like wax,
benzene, alcohol, thinner,
aromatic, or lubricant, etc.
For special cleaning of
inner part per year, contact
to the service center.
Temp. UP Button
Humidity UP Button
Temp. DOWN Button
TEMPERATURE
HUMI +
HUMIDITY
CAL
Egg-Turning Setting Button
CAL
TEMP -
Setting Button
HUMI -
TURN
Temp. Display
HEATING
HUMIDIFICATION
TURNING ON
WATER EMPTY
SET
Humidity Display
DIGITAL INCUBATOR
AUTOMATIC EG
G T U R N I N G - T E M P E R A T UR E&HUM I D I TY CONTROL
Heater Lamp
2. Identification of Parts
Humidity DOWN Button
New
Digital Incubator
TEMP +
Humidification working lamp
(Lighting when working)
(Lighting when working)
Egg-Turning Lamp
Vents for air circulation
For circulating warm air
Power Connecting
Egg Tray
For connecting
power cord.
Adjust the space of dividers
Water Supplement Lamp
Turn on with automatic egg-turning mode.
(Blink when working)
(Blink with water shortage)
according to egg size.
View Window
For a clear view of
the incubation process.
( duplicated View Window )
Air inlet vent
For inlet of air
from outside
8. Easy Function Operation
Water Cap
To facilitate water top-up
for the humidity control.
Digital Control Center
See description of
the function and operation.
Locking Button
Main Body-1 Main Body-2
REFER TO "HOW TO START INCUBATION" FOR MORE INFORMATION.
Function
Temp. Setting
Humidity Setting
3. Basic Components
Main Body-1
REA
R
Main Body-2
RE
Power Cord
Egg-Turning
Setting
FRON
T
User's Manual
Universal Tray
SET
TEMP +
TEMP -
SET
HUMI +
HUMI -
SET
TURN
Setting of required temp.
Setting of required humidity.
Egg-Turning Setting /
Cancellation
AR
Cels. / Fahr.
interchangable
View Window
Explanation
How to Operate
TEMP +
Incubator Initialization
(Factory Setting)
SET
How to turn off
Humidification Function
SET
SET
TEMP -
℃↔℉
How to change Cels. or Fahr.
Initialization
HUMI -
UNDER 40%
"OFF"
In case of low humidity
incubation
※ If you want to change setting value, keep pressing "SET" button and change the value.