DVD-SR270M
DVD-SR275M
DVD Recorder
user manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please register your product at
www.samsung.com/global/register
Getting Started
Getting Started
IMPORTANT NOTE
Warning
The mains lead on this equipment is supplied with a
moulded plug incorporating a fuse. The value of the fuse
is indicated on the pin face of the plug. If it requires
replacing, a fuse approved to BS1362 of the same rating
must be used.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Never use the plug with the fuse cover omitted if the
cover is detachable. If a replacement fuse cover is
required, it must be of the same colour as the pin face of
the plug. Replacement covers are available from your
dealer.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
Do not install this equipment in a confined space such as
a bookcase or similar unit.
WARNING : To prevent damage which may result in fire
or electric shock hazard, do not expose this
appliance to rain or moisture.
CAUTION : DVD Recorder USES AN INVISIBLE LASER BEAM
WHICH CAN CAUSE HAZARDOUS RADIATION
EXPOSURE IF DIRECTED. BE SURE TO OPERATE
DVD Recorder CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
This product satisfies CE regulations when shielded
cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic
interference with electric appliances, such as radios and
televisions, use shielded cables and connectors for
connections.
If the fitted plug is not suitable for the power points in
your house or the cable is not long enough to reach a
power point, you should obtain a suitable safety
approved extension lead or consult your dealer for
assistance.
However, if there is no alternative to cutting off the plug,
remove the fuse and then safely dispose of the plug. Do
not connect the plug to a mains jack, as there is a risk of
shock hazard from the bared flexible cord.
To disconnect the apparatus from the mains, the plug
must be pulled out from the mains socket, therefore the
mains plug shall be readily operable.
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This licence is limited to private noncommercial use by end-user consumers for licensed
contents.
No rights are granted for commercial use.
The licence does not cover any product unit other than
this product unit and the licence does not extend to any
unlicensed product unit or process conforming to ISO/
IEC 11172-3 or ISO/IEC 13818-3 used or sold in
combination with this product unit. The licence only
covers the use of this product unit to encode and/or
decode audio files conforming to the ISO/IEC 11172-3 or
ISO/IEC 13818-3. No rights are granted under this licence
for product features or functions that do not conform to
the ISO/IEC 11172-3 or ISO/IEC 13818-3.
English - 2
Handling Cautions
• Before connecting other components to this DVD
Recorder, be sure to turn them all off.
Important Safety Instructions
• Do not move the DVD Recorder while a disc is being
played, or the disc may be scratched or broken, the
DVD Recorder internal parts may be damaged.
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
• Do not put a flower vase filled with water or any small
1) Read these instructions.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the disc
2) Keep these instructions.
metal objects on the DVD Recorder.
tray.
3) Heed all warnings.
• Exterior interference such as lightning and static
4) Follow all instructions.
electricity can affect normal operation of this DVD
Recorder. If this occurs, turn the DVD Recorder off and
on again with the STANDBY/ON button, or disconnect
and then reconnect the AC power cord to the AC
power outlet. The DVD Recorder will operate normally.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding- type plug. A polarized plug has two
blades with one wider than the other. A groundingtype plug has two blades and a third grounding
prong. The wide blade or the third prong is provided
for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of
the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, the point where they exit from the
apparatus.
• Be sure to remove the disc and turn off the DVD
Recorder after use.
• Disconnect the AC power cord from the AC outlet
when you don’t intend to use the DVD Recorder for
long periods of time.
• Clean the disc by wiping in a straight line from the
inside to the outside of the disc.
• Apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed on
the apparatus.
• The Mains plug is used as a disconnect device and shall stay
readily operable at any time.
11) Only use attachments/accessories specified by the
manufacturer.
Maintenance of Cabinet
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
For safety reasons, be sure to disconnect the AC power
cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for
cleaning.
• Wipe the cabinet with a soft cloth.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
English - 3
Getting Started
Precaution
• If you move your DVD Recorder suddenly from a cold
Getting Started
Disc Handling
place to a warm place, condensation may generate on
the operating parts and lens and cause abnormal disc
playback. If this occurs, do not connect the plug to the
power outlet and wait for two hours. Then insert the
disc and try to play back again.
• Use discs with regular
shapes. If an irregular disc (a
disc with a special shape) is
used, this DVD Recorder may
be damaged.
Disc Specifications
Holding discs
• DVD-SR270M
This unit allows you to record and playback high quality
digital images on a DVD-RAM/DVD-RW/DVD-R disc.
You can record and edit digital video on DVD-RAM/DVDRW/DVD-R discs.
(DVD+RW/DVD+R discs can be played, but cannot be
recorded.).
• Avoid touching the surface of a disc
where recording is performed.
DVD-RAM, DVD±RW and DVD±R
• DVD-SR275M
This unit allows you to record and playback high quality
digital video on DVD-RAM/DVD±RW/DVD±R discs.
You can record and edit digital images on DVD-RAM/
DVD±RW/DVD±R discs.
• Clean with an optional DVD-RAM/PD
disc cleaner (LF-K200DCA1 where
available). Do not use cleaners or
cloths for CDs to clean
DVD-RAM/DVD±RW/±R discs.
DVD-Video, Audio-CD
Disc Type
• Wipe off dirt or contamination on the disc with a soft
◆ DVD-Video
cloth.
• A digital versatile disc (DVD) can contain up to
135-minutes of images, 8 audio languages and 32
subtitle languages. It is equipped with MPEG-2 picture
compression and Dolby digital surrounding, allowing
you to enjoy vivid and clear theatre quality images in
the comfort of your own home.
Cautions on handling discs
• Do not write on the printed side with a ball-point pen
or pencil.
• Do not use record cleaning sprays or antistatic. Also, do
• When switching from the first layer to the second layer
of a dual-layered DVD Video disc, there may be
momentary distortion in the image and sound. This is
not a malfunction of the unit.
not use volatile chemicals, such as benzene or thinner.
• Do not apply labels or stickers to discs. (Do not use
discs fixed with exposed tape adhesive or leftover
peeled-off stickers.)
• Once a DVD-RW(V)/-R(V)/+R recorded is finalised, it is
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers available on
the market.
playable in a standard DVD player..
◆ Audio CD
• An audio disc on which 44.1 kHz PCM Audio is
• Do not load warped or cracked discs.
recorded.
• Plays CD-DA format audio CD-RW and CD-R discs.
• The unit may not be able to play some CD-RW or
Disc Storage
CD-R discs due to the condition of the recording.
Be careful not to harm the disc because the data on these
discs is highly vulnerable to the environment.
•
•
•
•
Do not keep under direct sunlight.
Keep in a cool ventilated area.
Store vertically.
Keep in a clean protection jacket.
CD-RW/-R
◆ MP3 CD-RW/-R
• Only CD-R discs with MP3 files recorded with ISO9660
or JOLIET format can be played back.
• Only MP3 files with the “mp3” or “MP3” extension can
be used.
• Playable bitrate range is from 32 Kbps to 320Kbps.
English - 4
• The unit can handle a maximum of 499 files and
finishes.
• This product optimizes the DVD+R for each recording.
• DVD-RAM/DVD±RW/DVD±R discs that contain MP3
Optimizing is carried out when you start recording
after inserting the disc or turning on the unit.
Recording onto the disc may become impossible if
optimizing is carried out too many times.
files can be played back.
◆ JPEG CD-RW/-R
• Only JPEG files with the “.jpg”, “.JPG” extension can be
• Playback may be impossible in some cases due to the
used.
condition of recording.
• The unit can handle a maximum of 1000 files and
• This unit can play back DVD+R discs recorded and
folders.
finalised with a Samsung DVD video recorder. It may
not be able to play some DVD+R discs depending on
the disc and the condition of the recording.
• Maximum size of progressive JPEG is 3M pixels.
• MOTION JPEG is not supported.
• DVD-RAM/DVD±RW/DVD±R discs that contain JPEG
◆ DVD-RW/-R Disc Playback and Recording
files can be played back.
• Recording and playback can be performed on
◆ CD-RW/-R
DVD-RW/-R discs in both the Video and VR Modes.
• Use a 700MB (80 minutes) CD-RW/-R disc.
• Once a DVD-RW/-R recorded in both the Video and VR
If possible, do not use a 800MB (90 minutes) or above
disc, as the disc may not play back.
Modes is finalised, you cannot perform additional
recording.
• If the CD-RW/-R disc was not recorded as a closed
• Once a DVD-RW/-R recorded in Video Mode is finalised,
session, you may experience a delay in the early
playback time, all recorded files may not play.
it becomes DVD-Video.
• In both modes, playback can be performed before and
• Some CD-RW/-R discs may not be playable with this
unit, depending on the device which was used to burn
them. For contents recorded on CD-RW/-R media from
CDs for your personal use, playability may vary
depending on contents and discs.
after finalisation, but additional recording, deleting and
editing can not be performed after finalisation.
• If you want to record the disc in VR Mode and then
record in V Mode, be sure to execute Format. Be careful
when executing Format because all the recorded data
may be lost. You can change the disc mode only one
times when the unused DVD-R disc is inserted.
◆ Using MPEG4 disc
• Video File with following extensions can be played. :
• DVD-RW/-R (VR mode)
.avi, .divx, .AVI, .DIVX
– You can record multiple titles, edit, delete, partial delete,
create a playlist, etc.
– A disc that is recorded in this mode may not be played by
existing DVD Recorder.
• DivX Video (Codec) Format : DivX 3.11 DivX 4.x DivX 5.x
(without QPEL and GMC)
• DivX Audio (Codec) Format : MP3, AC3, DTS
• Supported subtitle fi le formats: .smi, .srt, .sub, .txt, .ass
• Each folder can have up to 500 items including files and
• DVD-RW/-R (Video mode)
– The disc can be played by an existing DVD player
once it has been finalised.
– If a disc that has been recorded in Video Mode by a
different maker’s recorder but has not been finalised,
it cannot be played or additionally be recorded by
this DVD Recorder.
sub folders.
• You cannot play back the disc that is larger than a 720
x576 pixel resolution.
◆ DVD+R Disc Playback and Recording
• Once a DVD+R recorded in Video Mode is finalised, it
– When programming is erased from a DVD-R, that space
does not become available. Once an area on a DVD-R is
recorded on, that area is no longer available for
recording, whether the recording is erased or not.
becomes DVD-Video.
• You can record onto the available space on the disc and
perform editing functions such as giving titles to discs
and programmes and erasing programmes before
finalising.
• When programming is erased from a DVD+R, that space
does not become available. Once an area on a DVD+R is
recorded on, that area is no longer available for
recording, whether the recording is erased or not.
◆ DVD+RW Disc Playback and Recording
• With DVD+RW discs, there is no difference between
DVD-Video format (Video mode) and DVD-Video
Recording format (VR mode).
• Finalising is generally unnecessary when using a
• It takes about 30 seconds for the unit to complete
recording management information after recording
English - 5
DVD+RW disc.
Getting Started
folders.
Getting Started
◆ DVD-RAM Disc Playback
played with this product.
• You cannot play a DVD-RAM in most DVD components
❋ For more information on DVD recording
compatibility, consult your DVD-RAM/DVD±RW/
DVD±R manufacturer.
due to compatibility issues.
• Only DVD-RAM standard Version 2.0. discs can be
played in this unit.
❋ Use of poor quality DVD-RAM/DVD±RW/DVD±R discs
may cause following unexpected problems
including, without limitation, recording failure, loss
of recorded or edited materials or damage to the
DVD Recorder.
• For cartridge type DVD-RAM discs, remove the
cartridge and use the disc only.
• DVD-RAM recorded on this unit may not work with
other DVD Players. To determine compatibility with
• these DVD-RAM discs, refer to the user’s manual for the
player.
Do not use the following discs!
• LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should
not be used in this product.
COPY PROTECTION
[Note]
• Many DVD discs are encoded with copy
Disc types that can be played : CD/CD-RW/-R/MP3/
JPEG/DVD-Video/DVD-RAM/DVD±RW/±R.
For a DVD-RW/-R disc, which has been recorded in
Video Mode on another component, it can play only
when finalised.
protection.
• This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of this
copyright protection technology must be
authorised by Macrovision Corporation, is
intended for home and other limited viewing uses
only unless otherwise authorised by Macrovision
Corporation. Reverse engineering or disassembly
is prohibited.
• Some commercial discs and DVD discs purchased
outside your region may not be playable with this
product. When these discs are played, either “No disc.”
or “Please check the regional code of the disc.” will be
displayed.
• If your DVD-RAM/DVD±RW/±R discs is an illegal copy
or is not in DVD video format, it may also not be
playable.
Protection
This DVD Recorder can allow you to protect the contents
of your discs, as described below.
◆ Disc compatibility
• A 8X speed DVD+RW or greater disc can be played, but
maximum recording speed is 4x.
• Programme-protected : See page 67 “Locking
• Not all brands of discs will be compatible with this unit.
(Protecting) a Title”
• Disc-protected : See page 74 “Disc Protection”
❋ DVD-RAM/DVD±RW/DVD±R discs that are
incompatible with the DVD-VIDEO format cannot be
English - 6
Getting Started
System Setup
 Warning...................................................................................................2
 On-Screen Menu Navigation.......................................................23
 Precaution ..............................................................................................3
Important Safety Instructions........................................................3
Handling Cautions ..............................................................................3
Maintenance of Cabinet...................................................................3
Disc Handling .......................................................................................4
Disc Storage...........................................................................................4
Disc Specifications ..............................................................................4
 Plug & Auto Setup ...........................................................................23
 Contents..................................................................................................7
 General Features..................................................................................9
 Before reading the user’s manual .............................................10
 How to use the DVD Recorder....................................................10
 Unpacking...........................................................................................12
 Description .........................................................................................14
Front Panel .........................................................................................14
Rear Panel............................................................................................15
Front Panel Display..........................................................................16
Tour of the Remote Control .........................................................17
Connecting & Setting Up
 Connecting DVD Recorder to the
TV using the RF Cable ...................................................................18
 Connecting the SCART Cable .....................................................18
Case 1 : Connecting DVD Recorder to the TV using
the SCART Cable ...............................................................................18
Case 2 : Connecting DVD Recorder to a Satellite
Receiver or Other Equipment .....................................................19
 Connecting the Audio/Video Cable .........................................19
 Connecting the Component Video Cable .............................19
 Connecting HDMI/DVI to a TV (DVD-SR275M only) ..........20
Case1 : Connecting to a TV with HDMI jack ..............................20
Case 2 : Connecting to a TV with DVI jack .................................20
 AV Receiver Connections ..............................................................22
 Connecting External Devices ......................................................22
Case1 : Connecting an external devices to the AV3 jacks.....22
Case 2 : Connecting a DV Device to the DV IN jack
(DVD-SR275M only) .......................................................................22
 Clock Set ..............................................................................................24
Time Zone ...........................................................................................24
Daylight Saving Time......................................................................25
Auto Adjust .........................................................................................25
Present Time.......................................................................................25
 Tuner Preset .......................................................................................26
Auto Setup ..........................................................................................26
Digital Manual Setup ......................................................................27
Analogue Manual Setup ...............................................................27
Analogue Channel List...................................................................27
Digital Channel List .........................................................................28
Digital Favourite Channel .............................................................28
 Setting up the Features .................................................................28
DVD Auto Chapter ...........................................................................29
Format DVD-RW ...............................................................................29
EZ Record.............................................................................................29
Anynet+(HDMI-CEC) (DVD-SR275M only) .............................30
Language Follow (DVD-SR275M only) ....................................31
DVD Bilingual Rec. ...........................................................................31
DVB-T Auto Subtitle .......................................................................31
DivX Registration Code..................................................................31
 Setting up the Options ..................................................................32
Language.............................................................................................32
 Setting up the Parental..................................................................32
If you forgot your password ........................................................33
Setting the Program Grade ..........................................................33
Setting the Rating Level ................................................................33
Changing the Password ................................................................33
 Setting up the Front Display .......................................................34
 Setting up the Video Options .....................................................34
 Setting up the Audio Options ....................................................37
DTV Functions
 Basic Functions..................................................................................40
Display Screen ...................................................................................40
Select Audiotrack .............................................................................40
Setting the Favourite Channel....................................................41
English - 7
Getting Started
Contents
Getting Started
Changing the Subtitle Language ..............................................41
Using the digital text service.......................................................41
 Guide .....................................................................................................42
Guide Timer Recording ..................................................................42
Playback
 Region code (DVD-Video only) ..................................................43
 Logos of Discs that can be played ............................................43
 Disc types that can be played.....................................................43
 Playing a Disc .....................................................................................44
 Using the Disc Menu & Title Menu ...........................................45
 Using the playback related buttons .........................................46
 Using the ANYKEY button ............................................................47
 Selecting the Audio language ....................................................47
 Remain..................................................................................................48
 Selecting the Subtitle Language ...............................................48
 Changing the Camera Angle.......................................................48
 Playing an Audio CD/MP3 ............................................................49
 Playing back a Picture Disc ..........................................................50
Editing
 Playing the Title List ........................................................................65
 Basic Editing (Title List) ..................................................................66
Changing the Name of a Title (Title Name)...........................66
Locking (Protecting) a Title .........................................................67
Erasing a Title (Title Erase) ...........................................................67
Erasing a chapter (Chapter Erase) ............................................68
Erasing a section of a Title (A-B Erase) ...................................69
Dividing a title into two (Divide Title) ...................................70
 Advanced Editing (Playlist) ..........................................................71
Creating a Playlist ............................................................................71
Playing Titles in the Playlist .........................................................72
Editing a Playlist ...............................................................................72
Renaming a Playlist Title ...............................................................72
Deleting a Playlist Title from the Playlist ................................73
 Disc Setting.........................................................................................74
Editing the Disc Name ...................................................................74
Disc Protection ..................................................................................74
Formatting a Disc .............................................................................75
Finalising a Disc.................................................................................76
Unfinalising a Disc (V/VR mode) ...............................................76
Disc Information ..............................................................................77
Erase All Titles ...................................................................................77
 Playing an MPEG4 Disc ..................................................................51
Reference
Recording
 Troubleshooting ...............................................................................78
 Recordable Discs ..............................................................................52
 Specifications .....................................................................................80
 Recording Formats ..........................................................................53
 Warranty ..............................................................................................81
 Recording Mode ...............................................................................54
 Unrecordable pictures ...................................................................55
 Recording immediately .................................................................56
 Recording through the DV Input jack
(DVD-SR275M only) .......................................................................57
 Making a One Touch Recording (OTR) ....................................58
 Making a Timer Recording ..........................................................58
 Editing the Timer List......................................................................61
 Deleting the Timer List...................................................................61
 Using the VIDEO Plus+ Feature ..................................................62
 Check Remaining Time ..................................................................63
 DV Dubbing (DVD-SR275M only)..............................................63
English - 8
• DVD-SR270M
This unit allows you to record and playback high quality
digital images on a DVD-RAM/DVD-RW/DVD-R disc.
You can record and edit digital video on DVD-RAM/DVDRW/DVD-R discs.
(DVD+RW/DVD+R discs can be played, but cannot be
recorded.).
• DVD-SR275M
With the DVD-Recorder, you can create your own DVD
Video titles on 4.7 GB DVD±RW/DVD±R or 8.5 GB DVD±R
discs.
Dubbing data from a digital camcorder using a
DV input jack
Record DV Device video onto DVD-RAM, DVD±RW or
DVD±R discs using the DV input jack (IEEE 13944pin/4pin). (See pages 56, 63) (DVD-SR275M only)
This unit allows you to record and playback high quality
digital video on DVD-RAM/DVD±RW/DVD±R discs.
You can record and edit digital images on DVD-RAM/
DVD±RW/DVD±R discs.
High quality progressive scan
High quality digital audio and video recording
and playback
You can record up to approximately 16-hours of video on
a double side 9.4 GB DVD-RAM disc up to 15-hours on
a dual-layer 8.5 GB DVD±R disc up to 8-hours on a 4.7GB
DVD-RAM/DVD±RW/DVD±R disc, depending on the
recording mode.
Progressive scanning provides high resolution and flicker
free video. The 10-bit 108-MHz DAC and 2D Y/C
Separating Circuitry provides the highest image playback
and recording quality. (See page 35)
MPEG4 playback
This DVD Recorder can play MPEG4
formats and AVI files.
Creating a DVD video title using DVD±RW/±R
disc
DivX Certification
With the DVD Recorder, you can create your own DVD
Video titles on 4.7 GB DVD±RW/±R or 8.5GB
DVD±R discs.
DivX, DivX Certified, and associated logos are trademarks
of DivX Networks, Inc and are used under licence.
Official DivX® Certified product
Plays all versions of DivX® video (including DivX® 6) with
standard playback of DivX® media files
Selectable Recording Mode
You can set your DVD Recorder to one of eight different
recording modes, each varying in recording quality and
length. Select a recording mode according to the time
and picture quality you need. For example, if picture
quality is your top priority, select “HQ” (high quality). If
recording time is your priority, “SLP” can be a possible
choice. (Analogue mode only)
DVB-T recording is possible only on AUTO mode.
The Dual layer DVD-Rs have approximately double the
capacity of single layer DVD-Rs.
HDMI (High Definition Multimedia Interface)
HDMI reduces picture noise by allowing a pure digital
video/audio signal path from the DVD recorder to your
TV. (DVD-SR275M only)
EZ Record Mode
This function allows you initialise and Finalise a disc
automatically. (See page 28)
Automated Quality Adjustment for Timer
Recording
If AUTO mode is selected, the video quality is adjusted
automatically so that all video for the scheduled time can
be recorded onto the free disc space.
(See page 58)
EPG functions
EPG is an Advanced Electronic Programme Guide.
With a Remote Control Unit, you can operate full
function. It has a Auto and Manual Scan facility and
Channel Organizing (programmable) facility.
English - 9
Getting Started
Creating a DVD video title using DVD±RW/
DVD±R disc
General Features
Getting Started
Before reading the user’s manual
How to use the DVD Recorder
Make sure to check the following terms before reading
the user manual.
Icons that will be used in manual
Icon
Z
X
C
V
K
L
B
G
A
D
J
M
N
H
Term
DVD
RAM
Please check available disc type before recording.
Definition
This involves a function available on
DVD or DVD-RW(V)/-R(V)/+R discs
that have been finalised.
This involves a function available on
DVD-RAM.
This involves a function available on
-RW
DVD-RW.
This involves a function available on
-R
DVD-R.
This involves a function available on
+RW
DVD+RW.
This involves a function available on
+R
DVD+R.
This involves a function available on
CD
a data CD (CD-RW or CD-R).
This involves a function available on
JPEG
CD-RW/-R, DVD-RAM/DVD±R/±RW
discs.
This involves a function available on
MP3
CD-R/-RW, DVD-RAM/DVD±R/±RW
discs.
This involves a function available on
DivX
DVD-RAM/DVD±RW/DVD±R discs.
This involves a case where a
Caution function does not operate or
settings may be cancelled.
This involves tips or instructions on
NOTE
the page that help each function
operate.
One-Touch A function that can be operated by
button
using only one button.
ANYKEY
button
Step 1 : Select the disc type
A function that can be operated by
using ANYKEY button.
• DVD-SR270M
(DVD+RW/DVD+R discs can be played, but cannot be
recorded.)
• DVD-SR275M
If you want to repeatedly record on the same disc or you
want to edit the disc after recording, select a rewritable
DVD-RAM or DVD±RW type disc.
If you want to save recording without any change, choose
a non-rewritable DVD±R.
Step 2 : Format the disc to start recording
The DVD Recorder automatically starts formatting when
an unused disc is inserted. This is required for the
preparation of recording on a disc.
Using a DVD-RAM/±RW/+R
When an unused DVD-RAM/±RW/+R disc is fi rst inserted,
the message “Unformatted Disc. Formatting.
Please wait.” will be displayed.
Using a DVD-R
It is not necessary to format a new DVD-R disc. When it is
inserted, it will operate in Video mode.
It can also be formatted in VR mode in the setup menu.
You can change the disc mode only once when an
unused DVD-R disc is inserted.
M  You can only use either the VR or Video mode on a
About the use of this user’s manual
1) Be sure to be familiar with Safety Instructions before
using this product. (See pages 2~6)
2) If a problem occurs, check the Troubleshooting.
(See pages 85~87)
Copyright
©2008 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s manual
may be reproduced or copied without the prior written
permission of Samsung Electronics Co.
English - 10
DVD-RW/-R, but not both at the same time.
 You can format a DVD-RW/-R to V or VR mode
using Disc Setting. It should be noted that the
disc’s data will be lost when changing formats.
Step 3 : Recording
Step 4 : Playing
To start playback, select the title you want to play from
the title list.
A DVD consists of sections called titles, and sub- sections
called chapters.
During recording, a title is created between two points
where you start and stop recording.
Chapters will be created automatically regardless of the
disc type when it is set at the setup menu.
To play your DVD on other DVD components, finalising
may be necessary. First, finish all editing and recording
operations, then finalise the disc.
When using a DVD-RW/-R disc in VR Mode
Although finalising is generally unnecessary when
playing the disc on a VR Mode compatible component, a
fi nalised disc should be used for playback..
When using a DVD-RW/-R disc in Video Mode
The disc should be finalised first to enable playback on
anything other than this DVD Recorder. No more editing
or recording can be made on the disc once it has been
finalised.
To enable recording on the disc again, the disc must be
unfinalised.
When using a DVD+R disc
You should finalise the disc to play it on a component
other than this DVD Recorder. No more editing or
recording can be made on the disc once it has been
finalised.
M  You can finalise the disc automatically using EZ
Step 5 : Editing a recorded disc
Editing on discs is easier than conventional video tapes.
The DVD Recorder supports many different edit
functions, possible only with DVDs.
With a simple and easy edit menu, you can operate
various edit functions, such as delete, dubbing, rename,
lock, etc., on a recorded title.
Creating a playlist (DVD-RAM/-RW/-R in VR mode)
With this DVD Recorder, you can create a new playlist on
a disc and edit it without the original, pre-existing
recording.
English - 11
Record. (See page 29)
Getting Started
There are two different recording methods, Direct
Recording and Timer Recording. Timer Recording is
classified as follows: Recording mode : HQ (high quality
mode), HSP, SP (standard quality mode), LSP, ESP, LP, EP,
SLP (Long duration mode) according to the recording
mode. When recording is set in the AUTO mode, the best
quality picture is recorded with regards to the remaining
time on the disc.
Step 6 : Finalising & Playing on other
DVD components
Getting Started
Preparing the Remote Control
Unpacking
Install Batteries in the Remote Control
• Open the battery cover on the back of the remote
Accessories
control.
Check for the supplied accessories below.
• Insert two AAA batteries. Make sure that the polarities
(+ and –) are aligned correctly.
• Replace the battery cover.
If the remote does not operate properly :
Video/Audio Cable
RF Cable for TV
•
•
•
•
Check the polarity +/– of the batteries (Dry-Cell)
Check if the batteries are drained.
Check if remote sensor is blocked by obstacles.
Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
Remote Control
Batteries for Remote
Control (AAA Size)
To determine whether your television is
compatible, follow the instructions below.
1. Switch your television on.
User’s Manual
Quick Guide
2. Point the remote control towards the television.
3. Press and hold the TV STANDBY/ON button and
enter the two-figure code corresponding to the brand
of your television, by pressing the appropriate
number buttons.
English - 12
Controllable TV Codes
BUTTON
SALORA
74
SAMSUNG
01, 02, 03, 04, 05, 06, 07, 08, 09
SANYO
41, 42, 43, 44, 48
AIWA
82
SCHNEIDER
6
ANAM
10, 11, 12, 13, 14, 15, 16, 17, 18
SELECO
74
BANG & OLUFSEN
57
SHARP
36, 37, 38, 39, 48
BLAUPUNKT
71
SIEMENS
71
BRANDT
73
SINGER
57
BRIONVEGA
57
SINUDYNE
57
CGE
52
SONY
35, 48
CONTINENTAL
EDISON
75
TELEAVA
73
DAEWOO
19, 20, 23, 24, 25, 26, 27, 28, 29,
30, 31, 32, 33, 34
EMERSON
64
FERGUSON
73
FINLUX
06, 49, 57
FORMENTI
57
FUJITSU
84
GRADIENTE
70
GRUNDIG
49, 52, 71
HITACHI
60, 72, 73, 75
IMPERIAL
52
JVC
61, 79
LG
06, 19, 20, 21, 22, 78
LOEWE
06, 69
LOEWE OPTA
06, 57
MAGNAVOX
40
METZ
57
MITSUBISHI
06, 48, 62, 65
MIVAR
52, 77
TELEFUNKEN
67, 73, 75, 76
THOMSON
72, 73, 75
THOMSON ASIA
80, 81
TOSHIBA
47, 48, 49, 50, 51, 52
WEGA
57
YOKO
6
ZENITH
63
Result : If your television is compatible with the remote
control, it will switch off.
It is now programmed to operate with the remote
control.
M  If several codes are indicated for your television
brand, try each one in turn until you find one that
works.
 If you replace the remote control’s batteries, you
must set the brand code again.
Then you can control the television using the
following buttons after pressing the TV button.
Button
Function
NEC
83
NEWSAN
68
TV STANDBY/ON Used to switch the television on and off.
NOBLEX
66
INPUT SEL.
Used to select an external source.
NOKIA
74
TV VOL (+ –)
NORDMENDE
72, 73, 75
Used to adjust the volume of the
television.
PANASONIC
53, 54, 74, 75
PHILIPS
06, 55, 56, 57
PHONOLA
06, 56, 57
PIONEER
58, 59, 73, 74
RADIOLA
06, 56
RADIOMARELLI
57
RCA
45, 46
REX
74
SABA
57, 72, 73, 74, 75
PROG/TRK (,.) Used to select the desired channel.
TV MUTE
Used to toggle the sound on and off.
Number
Used to input number directly.
M  The functions listed above will not necessarily
work on all televisions. If you encounter problems,
operate the television directly.
English - 13
Getting Started
BRAND
BUTTON
BRAND
Getting Started
Description
Front Panel (DVD-SR270M)
1
2
8
5
4
11
6
3
1.
STANDBY/ON BUTTON
7.
RECORD BUTTON
2.
VIDEO INPUT JACK (AV3 IN)
8.
FRONT PANEL DISPLAY
3.
AUDIO INPUT JACK (AV3 IN)
9.
SEARCH/SKIP BUTTON
4.
DVD DECK
10. STOP BUTTON
5.
DVD OPEN/CLOSE BUTTON
11. PLAY/PAUSE BUTTON
6.
INPUT BUTTON
7
9 10 9
Front Panel (DVD-SR275M)
1
2
3
9
6
5
12
7
4
1.
STANDBY/ON BUTTON
7.
INPUT BUTTON
2.
VIDEO INPUT JACK (AV3 IN)
8.
RECORD BUTTON
3.
AUDIO INPUT JACK (AV3 IN)
9.
FRONT PANEL DISPLAY
4.
DV INPUT JACK
10. SEARCH/SKIP BUTTON
5.
DVD DECK
11. STOP BUTTON
6.
DVD OPEN/CLOSE BUTTON
12. PLAY/PAUSE BUTTON
English - 14
8
10 11 10
1
4
5
2
3
4
5
2
3
6
7
6
7
Getting Started
Rear Panel (DVD-SR270M)
Rear Panel (DVD-SR275M)
8
1
1.
RF IN/RF OUT JACK
6.
COMPONENT VIDEO OUT JACKS
2.
AV1 (TV) IN/OUT SCART
7.
VIDEO/AUDIO LINE OUT JACKS
3.
DIGITAL AUDIO OUT JACK (COAXIAL)
8.
HDMI JACK (DVD-SR275M only)
4.
AV2 (EXT) SCART
5.
AUDIO L, R OUT JACKS
M  The Antenna connection does not pass the output
signal of the DVD Recorder.
To watch output signal of the DVD Recorder, you
must connect audio/video or Scart cables.
English - 15
Getting Started
Front Panel Display
1
2
3
4
5
DVD
CD
6
RW
REC
HDMI
1080iP720P
7
9
8
1. STOP, PAUSE and OPEN/CLOSE indicator
7. Lights to indicate the timer record mode
2. PLAYBACK, SKIP/SEARCH indicator
8. HDMI indicator :
HDMI 480P k “HDMI”,
HDMI 720P k “HDMI + 720P”,
HDMI 1080i k “ HDMI + 1080i”,
HDMI 1080P k “ HDMI + 1080P”.
3. In Disc Indicator : DVD Video, Audio CD, CD-R/RW,
DVD-R/RW/RAM, DVD+R/RW
4. DVD VIEW indicator
5. CD indicator
6. Disc Media Indicator : DVD-R, DVD-RW, DVD+R,
DVD+RW
9. Display the total playing time and various messages
concerning operations such as PLAY, STOP, LOAD..
nodSC: No disc loaded.
OPEN: The disc tray is open.
LOAD: Player is loading disc information.
English - 16
Tour of the Remote Control
Your DVD Recorder remote control will work with Samsung televisions and compatible brands.
Brings up the DVD Recorder’s setup menu.
20
21
13. OK/Direction Buttons
(▲/▼/◄/► Buttons)
3
22
23
14. TITLE LIST/DISC MENU Button
Press this to enter the Title List/Disc menu.
4
5
24
16. A, B, C, D button
6
7
8
15. AUDIO Button
Use this to access various audio functions on a disc
(DVD mode) .
25
9
26
27
10
28
11
12
29
13
Press this when you use DTV functions.
17. ANYKEY Button
Press this to view the status of the disc that is being
played.
18. REC Button
Press this to make a recording on DVD-RAM/DVD±RW/+R
discs.
19.
14
15
16
30
31
17
18
19
32
33
34
INFO button
Press to display the programme information box in the
screen when you use DTV.
20. INPUT SEL. Button
Select input signal in external input mode
(Prog, AV1, AV2, AV3 or DV input).
21. TV/RADIO Button
In DTV mode, press this button to switch TV or Radio
mode.
22. TV STANDBY/ON Button
23. OPEN/CLOSE Button
To open and close the disc tray.
1. TV Button
Press this to operate TV.
24. SUBTITLE Button
Press this to switch the DVD’s subtitle language.
2. DVD Button
25. PAUSE Button
Press to pause a disc.
Press this when you use a DVD.
3. STANDBY/ON Button
4. Number Button
5. TV/DVD Button
6. Reverse/Forward Skip Buttons
Press to skip a disc backwards or forwards.
7. TV MUTE Button
This operates as sound mute (TV mode).
8. FAV LIST
When you use DTV, press this button to switch between
favourite list.
9. STOP button
Press to stop a disc.
10. TV VOL (Volume) Button
TV volume adjustment.
26. TEXT Button
When you use DTV, press this button to select the Digital
text OSD.
27. PLAY Button
Press to play playback/recording.
28. PROG Button
Press this to select a TV channel
29. RETURN Button
Returns to previous menu.
30. PLAY LIST/TITLE MENU Button
Press this to enter the Edit playlist/Title menu.
31. EXIT Button
32. GUIDE Button
Press this to switch programme guide.
11. DTV/ANALOG Button
Select Digital/Analogue broadcasting.
33. REC MODE Button
Press this to set the desired recording time and picture
quality.
12. MENU Button
34. CANCEL Button
English - 17
Connecting & Setting Up
1
2
Connecting & Setting Up
Connecting & Setting Up
Connecting DVD Recorder to the TV
using the RF Cable
Connecting the SCART Cable
Case 1 : Connecting DVD Recorder to the
TV using the SCART Cable
M  Make sure that both the television and the DVD
Recorder are switched off before connecting the
cables.
1. Remove the aerial or network input cable from the
television.
• Obtain better quality sound and pictures.
• Simplify the setting up procedure of your DVD
2. Connect this cable to the 75Ω aerial jack marked
on the rear of your DVD Recorder.
3. Plug the RF Cable supplied into the
DVD Recorder.
You can connect your DVD Recorder to the
television using the SCART cable if the appropriate
input is available on the television. You thus:
Recorder.
jack on your
M  Regardless of the type of connection chosen, you
must always connect the RF Cable. Otherwise, no
picture will be visible on the screen when the DVD
Recorder is switched off.
4. Plug the other end of the RF Cable into the connector
previously used for the aerial on the television.
 Make sure that both the television and the DVD
M  The RF cable connection of this product sends only
signal of TV. You must connect SCART cable or
Audio/Video cables to watch a signal from DVD
Recorder.
Recorder are switched off before connecting the
cables.
1. Connect the Aerial Cable.
2. Connect one end of the SCART cable to the AV1 (TV)
jack on the rear of the DVD Recorder.
3. Plug the other end into the appropriate connector on
the television.
To RF IN
Aerial
To RF OUT
SCART Cable
TV
RF Cable
ANT
To ANT INPUT
TV
ANT
RF Cable
English - 18
Case 2 : Connecting DVD Recorder to a
Satellite Receiver or Other Equipment
Connecting the Audio/Video Cable
You can connect your DVD Recorder to a Satellite
receiver or other DVD Recorder using the SCART cable if
the appropriate outputs are available on the equipment
chosen.
You can connect your DVD Recorder to the television
using the audio/video cable if the appropriate input is
available on the television.
1. Connect one end of the video cable into the VIDEO
output jack on the rear of the DVD Recorder.
3. Connect one end of the audio cables supplied into the
AUDIO output jacks on the rear of the DVD Recorder.
• Take care to respect the colour coding of the up and
down channels.
2. AV1 (TV) : By means of 21-pin Scart Cable
Connect the end of the SCART cable to the AV1 (TV)
jack on the rear of the DVD Recorder. Plug the other
end into the appropriate connector on the television.
4. Plug the other end of the audio cables into the
appropriate input connectors on the television.
Satellite Receiver or other
Equipment
Aerial Connector
yellow
white
red
white
red
yellow
TV
ANT
RF Cable
Connecting the Component Video
Cable
You will enjoy high quality accurate colour reproduction
images. Component video separates the picture element
into black and white(Y), blue(PB), red(PR) signals to
present most clear and clean images.
1. Connect Component video cables between the
COMPONENT VIDEO OUT jacks on the rear of the DVD
Recorder and COMPONENT VIDEO IN jacks on the rear
of the TV.
2. Connect audio cables between the audio output jacks
on the rear of the DVD Recorder and AUDIO IN jacks
on the rear of the TV.
English - 19
Connecting & Setting Up
2. Plug the other end of the video cable into the
appropriate input connector on the television.
1. AV2 IN (EXT): By means of 21-pin Scart Cable
Plug the SCART Cable with satellite receiver or other
equipment into the AV2 (EXT) jack on the rear of the
DVD Recorder.
After making this connection, select the source by
pressing the INPUT SEL. button for the AV2 input
sources.
 What is “Progressive Scan”?
• Take care to respect the colour coding of the up and
down channels.
Progressive scan has twice as many scanning lines as
the interlace output method has.
Progressive scanning method can provide better and
clearer picture quality.
• Press the input selector on your TV remote control until
the Component signal from the DVD Recorder appears
on your TV screen.
Connecting & Setting Up
 You must connect the DVD Recorder to the
component(s) before using the Progressive Scan
feature.
Connecting HDMI/DVI to a TV
(DVD-SR275M only)
green
white
blue
red
red
If your TV has an HDMI/DVI input, connect HDMI/DVI
cable to a TV. You will enjoy the best quality images and
sounds.
Case 1 : Connecting to a TV with HDMI
Jack
Component
cable
(not supplied)
COMPONENT INPUT
white
red
1. Connect one end of the HDMI-HDMI cable into the
HDMI OUT jack on the rear of the DVD Recorder.
red
2. Plug the other end of the HDMI-HDMI cable into the
appropriate input connector on the television.
blue
green
3. Press the input selector on your TV remote control
until the HDMI signal from the DVD Recorder appears
on your TV screen.
▌Progressive Scan
Your TV must support progressive scan input to allow to
watch progressive scan component video out.
(See page 35)
• Make sure that the colour coded connections match. That is,
the Y, PB and PR component output jacks of your DVD
Recorder should be connected to the exact corresponding
component input jacks on your TV.
Otherwise, red or blue images will be displayed on the TV
screen.
• Consumers should note that not all high definition television
sets are fully compatible with this product and may cause
artifacts to be displayed in the picture. In case of progressive
scan picture problems, it is recommended that you switch the
connection to the standard definition output.
If there are questions regarding your Samsung TV set’s
compatibility with this DVD Recorder, please contact our
customer service centre.
M  See your TV User’s Manual to find out if your TV
may differ from the illustration above.
Case 2 : Connecting to a TV with DVI
Jack
1. Connect one end of the HDMI-DVI cable into the
HDMI OUT jack on the rear of the DVD Recorder.
supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s
instructions regarding Progressive Scan settings in the
TV’s menu system.
 Depending on your TV, the method of connection
HDMI-HDMI Cable
(not supplied)
2. Plug the other end of the HDMI-DVI cable into the
DVI IN jack on the television.
3. Using the audio cables, connect the AUDIO (red and
white) OUT jacks on the rear of the DVD Recorder to
the AUDIO (red and white) IN jacks of your TV. Turn on
the DVD Recorder and TV.
English - 20
4. Press the input selector on your TV remote control
until the DVI signal from the DVD Recorder appears
on your TV screen.
J  Depending on the HDMI device (TV/HDMI
 If your TV has a HDMI/DVI input, connect HDMI/
DVI cable to a TV. You will enjoy the best quality
images and sounds.
 Please check the
logo (If your TV has an
logo, then it supports Anynet+ function.)
 Why does Samsung use HDMI?
Analogue TVs require an analogue video/audio
signal.However, when playing a DVD, the data
transmitted to a TV is digital. Therefore either a
digital-to-analogue converter (in the DVD
Recorder) or an analogue-to-digital converter (in
the TV) is required. During this conversion, the
picture quality is degraded due to noise and
signal loss. HDMI technology is superior because
it requires no D/A conversion and is a pure digital
signal from the DVD recorder to your TV.
 What is the HDCP?
HDCP (High-bandwidth Digital Content
Protection) is a system for protecting DVD content
outputted via HDMI from being copied. It
provides a secure digital link between a video
source (PC, DVD. etc) and a display device (TV,
projector. etc). Content is encrypted at the source
device to prevent unauthorized copies from being
made.
red
white
HDMI-DVI Cable
(not supplied)
red
white
M  If the DVD Recorder is connected to your TV in
HDMI 1080p output mode, you must use High
speed(category2) HDMI cable.
 To change HDMI output resolution, see page 35.
 HDMI (High Definition Multimedia Interface)
HDMI is an interface to enable the digital
transmission of video and audio data with just a
single connector. Since HDMI is based on DVI, it is
completely compatible with DVI. The only
difference between HDMI and DVI is that HDMI
supports multi-channel audio.
Using HDMI, the DVD recorder transmits a digital
video and audio signal and displays a vivid picture
on a TV having an HDMI input jack.
 HDMI connection description
HDMI connector - Both uncompressed video data
and digital audio data (LPCM or Bit Stream data).
English - 21
Connecting & Setting Up
Receiver) you use, audio may not be supported. If
TV does not support Dolby digital/DTS, Audio
output is not available when you set Digital
output as Bitstream or select DTS On in Audio
setup menu. In this case, set the digital audio
output to PCM or DTS Off.
- Though the DVD recorder uses a HDMI cable,
the DVD recorder outputs only a pure digital
signal to the TV.
- If TV does not support HDCP (High-bandwidth
Digital Content Protection), snow noise appears
on the screen
Connecting & Setting Up
AV Receiver Connections
Connecting External Devices
To take full advantage of the movie theatre experience
that DVD offers, you may want to connect your DVD
Recorder to a complete Surround Sound system,
including an A/V Receiver and six Surround Sound
speakers.
If your A/V receiver is equipped with a Dolby Digital
Decoder, you have the option to bypass the DVD
Recorder’s built-in Dolby Digital Decoder.
Use the Digital Audio Out connection below.
To enjoy Dolby digital or DTS sound, you must set up the
audio settings. (See page 37)
1. Connect a Digital Audio coaxial cables from the Digital
Audio Out jacks on the rear panel of the DVD Recorder
to their corresponding Digital Audio Input jacks on
your A/V Receiver:
Manufactured under license under U.S. Patent #: 5,451,942
& other U.S. and worldwide patents issued & pending.
DTS and DTS Digital Out are registered trademarks and the
DTS logos and Symbol are trademarks of DTS, Inc.
© 1996-2007 DTS, Inc. All Rights Reserved.
Case1 : Connecting an external devices
to the AV3 jacks
You can connect other audio/video equipment to your DVD
Recorder using audio/video cables if the appropriate outputs
are available on the equipment chosen.
1. Connect one end of the video cable into the VIDEO
input jack on the front of the DVD Recorder.
2. Plug the other end of the video cable into the
appropriate output connector on the other system
(VCR, STB or Camcorder, etc).
3. Connect one end of the audio cable supplied into the
AUDIO input jacks on the front of the DVD Recorder.
• Take care to respect the colour coding of the left and
right channels.
4. Plug the other end of the audio cable into the
appropriate output connectors on the other system
(VCR,STB or Camcorder, etc).
Manufactured under licence from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
Case 2 : Connecting a DV Device to the
DV IN jack (DVD-SR275M only)
Rear(L)
Rear(R)
Front(L)
Front(R)
Subwoofer Centre
To Digital Audio Input of an A/V Receiver with
a Dolby, MPEG2 or DTS Digital Decoder
If your DV Device has a DV output jack, connect it to the DV
input jack of your DVD Recorder.
• If your camcorder has a DV output jack, see page 57 or 63 for
more information.
M  If the input is not selected automatically, use
INPUT SEL. button to select proper input.
English - 22
System Setup
On-Screen Menu Navigation
12:00
Timer
Title List
Timer
Timer - Standard
Timer - VIDEO Plus+
Timer List
Edit
Disc
Setting
Setup
>Move
sOk
rReturn
eExit
The on-screen menus allow you to enable or disable various functions
on your DVD Recorder.
Press the MENU button to open the on-screen menu and then use the
following buttons to navigate through the on screen menus.
1. ▲▼ buttons
Press these buttons on the remote control to move the selection bar
▲▼ to cycle through the menu options.
3. RETURN button
Press this button on the remote control to return to the Previous menu
screen displayed or to exit the on-screen menu.
4. EXIT button
Press this button to exit the on-screen menu.
Plug & Auto Setup
Your DVD Recorder will automatically set itself up when it is plugged in
for the first time. TV stations and clock will be stored in memory.
The process takes a few minutes. Your DVD Recorder will then be ready
for use.
-:--
Initial Installation
: United Kingdom
English
: Français
English
: Español
GMT + 00:00
Deutsch
: Off
Italiano
Nederlands
Country
Language
Time Zone
Daylight Saving Time
2. Plug the DVD Recorder into the mains. “Auto” in the front panel display
flickers.
OK
>Move
sOk
eExit
-:--
Initial Installation
Time Zone
: United
Time Kingdom
Zone
: English
◄ GMT + 00:00
: GMT + 00:00
Daylight Saving Time
: Off
Country
Language
OK
►
|
|
|
OK
>Move
sOk
3. Press the OK button, then press the ▲▼ buttons to select the desired
language option. Press the OK button.
4. Press the ▼ button, then press the OK button.
Press the ◄► buttons to select the desired time zone option.
Press the ▼ buttons to select OK, then press the OK button.
5. Press the ▼ button, then press the OK button.
Press the ▲▼ buttons to select On or Off, then press the OK button.
eExit
-:--
Initial Installation
Country
: United Kingdom
Language
: English
Time Zone
: GMT + 00:00
Off
: Auto
On
Daylight Saving Time
1. Connect the RF cable as indicated on page 18.
(Connecting Your DVD Recorder to the TV Using the RF cable and Scart
cable (or Audio/Video cable).)
OK
>Move
sOk
eExit
English - 23
System Setup
2. OK button
Press this button on the remote control to confirm any new settings.
6. Press the ▼ button to select OK, then press the OK button.
Digital auto scan will be started.
After digital auto scan is completed, analogue auto scan will be started.
Auto Scanning
Digital 610.000MHz, BW:8MHz, FFT:Auto
DTV
Radio
7. After auto channel scan is completed, auto clock setting will be started
automatically after one minute. If you want to start auto clock setting
immediately, press OK button.
YLE PEILI
YLEN KLASSINEN
YLE FSR+
YLEMONDO
YLE X3M
YLE TV1
YLE TV2
YLE FST5
YLE24
YLE Teema
Progress
Signal status
eEXIT
8. Wait until current date and time are displayed automatically. If you
want to exit auto clock setting, press MENU button.
9. Press the OK button to save clock set.
Auto Scanning
ATV 1
CH
Name
004
---
Progress
System Setup
eEXIT
12:00
Clock Set
Set the time and date.
Day Month Year
01 01 2008 Tue
Hour Min Auto Adjust
12 : 00
mMove
sOk
On
rReturn
eExit
Clock Set
12:00
Setup
Title List
Timer
Edit
Disc
Setting
Tuner Preset
Clock Set
Video
Audio
Features
Options
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK button.
3. Press the ▲▼ buttons to select Clock Set, then press the OK button.
Setup
>Move
sOk
rReturn
eExit
Time Zone
12:00
Clock Set
Title List
Timer
Edit
◄ GMT + 00:00 ►
Disc
Setting
OK
Setup
mMove
To setup, follow steps 1~3
4. Press the ▲▼ buttons to select Time Zone, then press the OK button.
Select the time zone of your area using the ◄► buttons, then select
OK using ▲▼ button.
Time Zone
5. Press the OK button.
sOk
rReturn
eExit
‹ GMT (Greenwich Mean Time) Table
GMT
City
United Kingdom, Portugal
Country
GMT+0
Dublin, Edinburgh, London, Lisbon, Casablanca
France, Austria, Belgium,
Demark, Deutschland,
Netherlands, Italy, Norway, Spain,
Sweden, Swiss, Hungary, Czech
GMT+1
Berlin, Stockholm, Rome, Vienna, Paris, Madrid,
Prague, Warsaw, Brussel, Copenhagen, Oslo,
Bern, Budapest, Warszawa, Prague
Finland, Turkey, Greece
GMT+2
Athens, Helsinki, Istanbul, Cairo, Eastern
Europe, Pretoria, Israel
English - 24
Daylight Saving Time
To setup, follow steps 1~3 in page 24.
12:00
Clock Set
Title List
Timer
Edit
Time Zone
Daylight Saving Time : OffOff
Auto Adjust
: OffOn
Present Time
: Tue 1. 1.2008 12:00
Disc
Setting
4. Press the ▲▼ buttons to select Daylight Saving Time, then press OK
button.
5. Select the On or Off using the ▲▼ buttons, then press the OK button.
Setup
>Move
sOk
rReturn
eExit
Auto Adjust
Turns on the Auto Adjust function when a channel in your local area
broadcasts a time signal.
The Auto Adjust function is activated whenever the recorder is turned off.
Timer
Edit
Disc
Setting
Time Zone
Daylight Saving Time : On
Auto Adjust
: OffOn
Present Time
: OffOff
To setup, follow steps 1~3 on page 24.
4. Press the ▲▼ buttons to select Auto Adjust, the press the OK button.
5. Select the On or Off using the ▲▼ buttons, then press the OK button.
Setup
>Move
sOk
rReturn
eExit
M  If the recorder does not receive a time signal from any station,
"Auto Adjust" returns to "Off " automatically and the display for
setting the clock manually appears. See "Present Time" below.
Present Time
To setup, follow steps 1~3 on page 24.
12:00
Clock Set
Title List
Timer
Edit
Disc
Setting
Setup
>Move
Set the time and date.
Day Month Year
01 01 2008 Tue
5. Press the OK button, then the date and time will be saved.
If you don’t press the OK button, it will not be saved.
Hour Min
12 : 00
sOk
rReturn
4. Press the ▲▼ buttons to select Present Time, then press the OK
button.
Use the ▲▼◄ ► buttons to input Time, Date or Year.
Use number buttons to input clock data directly.
eExit
M  You must have the RF cable connected to set the Auto Adjust.
(See page 18)
 The DVD Recorder automatically sets the clock according to the time
signal broadcast between the channels PR1 to PR5. If there is no clock
in the analogue broadcast, the clock will be searched automatically in
the DVB-T. If you do not need the "Auto Adjust" function, select "Off ".
 If there is a difference between the time information of analogue
and the one of digital, you may not be available to the contents of
DVB-T normally.
English - 25
System Setup
12:00
Clock Set
Title List
Tuner Preset
This menu consist of 6 sub-menus (Digital Channel List,
Digital Favourite Channel, Auto preset, Digital Manual Setup, Analogue
Manual Setup, Analogue Channel List).
Auto Preset
12:00
Tuner Preset
Title List
Auto Preset
Digital Manual Setup
Digital Channel List
Digital Favorite Channel
Analog Manual Setup
Analog Channel List
Timer
Edit
Disc
Setting
This function allows you to download of the channels automatically
from the programmed load.
1. Press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press OK button.
Setup
System Setup
3. Press the ▲▼ buttons to select Tuner Preset, then press OK button.
>Move
sOk
rReturn
eExit
12:00
Tuner Preset
Title List
Auto Preset
Digital Manual Setup
Digital Channel List
Digital Favorite Channel
Analog Manual Setup
Auto
Setup
will remove
Analog
Channel
List all channels.
Press [Yes] to continue, [No] to exit.
Timer
Edit
Disc
Setting
Setup
Yes
>Move
5. Press the ◄► buttons to select Yes, and press the OK button.
6. Press the ▲▼◄► buttons to select desired options.
• Channel type : Press the ◄► buttons to select Digital, Analogue or All.
No
sOk
4. Press the ▲▼ buttons to select Auto Preset, then press OK button.
The Message “Auto Setup will remove all Channels. Press [Yes] to
continue, [No] to exit.
rReturn
eExit
(If you select Analogue, you can not select the Scan
Mode, Start frequency and End frequency.)
• Scan Mode : - Only Free : Receives signals except for the scrambled
Auto Scanning
Country
: ◄ United Kingdom ►
Channel type
:◄
Scan Mode
:◄
Digital
►
All
►
Start frequency
: ◄ CH 21/474000kHz ►
End frequency
: ◄ CH 69/858000kHz ►
Start
Cancel
(Channel type : Digital)
Auto Scanning
Digital 610.000MHz, BW:8MHz, FFT:Auto
DTV
Radio
signal.
- All : Receives signals including the scrambled signal.
• Start frequency/End frequency
7. Press the ◄► button to select Start, then press OK button.
Auto Scan will be started.
M  You can select RADIO mode by pressing the TV/RADIO button on
the remote control.
This button used to toggle the TV and RADIO mode.
YLE PEILI
YLEN KLASSINEN
YLE FSR+
YLEMONDO
YLE X3M
YLE TV1
YLE TV2
YLE FST5
YLE24
YLE Teema
Progress
Signal status
eExit
(Channel type : Analog)
Auto Scanning
ATV
1
CH
Name
004
---
Progress
eExit
English - 26
Digital Manual Setup
12:00
Tuner Preset
Title List
Auto Preset
Digital Manual Setup
Digital Channel List
Digital Favorite Channel
Analog Manual Setup
Analog Channel List
Timer
Edit
Disc
Setting
To setup, follow steps 1~3 on page 26.
4. Press the ▲▼ buttons to select Digital Manual Setup, then press OK
button.
Setup
>Move
sOk
rReturn
eExit
Manual Scanning
Country
:
United Kingdom
Channel type
:
Digital
Scan Mode
:◄
All
►
Channel Number
:◄
CH 5
►
Frequency
:◄
178750kHz
►
Bandwidth
:◄
8MHz
►
Signal status 0%
Cancel
5. Select the Channel Number which you want to find using ◄►
buttons.
Select Frequency and input the Frequency of the channel you want to
find by pressing the number button.
Select Bandwidth which you want to find using ◄► buttons.
When the valid frequency is input, the bandwidth is selected
automatically. You can select the value of 6,7 or 8 MHz. After select
option. Press OK button to start the scanning process.
Analogue Manual Setup
To setup, follow steps 1~3 on page 26
12:00
Tuner Preset
Title List
Timer
Edit
Disc
Setting
Auto Preset
Digital Manual Setup
Digital Channel List
Digital Favorite Channel
Analog Manual Setup
Analog Channel List
• Program : Press ▲▼ repeatedly to select the programme position
(01 to 99) for the channel and press the OK button.
Setup
>Move
sOk
rReturn
eExit
• Channel : Tune the channel using ▲▼ buttons.
• AFT : Fine tunes the channel to obtain a clearer picture. If the picture
is not clear, select “Off ” and press the OK button. When the fine
tuning bar appears, press the ◄► buttons to obtain a clearer
picture, then press the OK button.
Manual Set
Program
01
Channel
--AFT
On
Tuner Audio
NICAM
Station Name --->Move
4. Press the ▲▼ buttons to select Analogue Manual Setup, then press
OK button.
• Tuner Audio : Sets the channels for the NICAM broadcast.
Normally, select "NICAM." If the sound from the
NICAM broadcast is not clear, select "Standard" and
then press the OK button.
sOk
• Station Name : Display station name automatically detected in
broadcasting signal. If not detected, you can edit
name by using ▲▼◄► buttons.
12:00
Tuner Preset
Title List
Timer
Edit
Disc
Setting
Auto Preset
Digital Manual Setup
Digital Channel List
Digital Favorite Channel
Analog Manual Setup
Analog Channel List
You can swap or delete the desired channel in the channel list.
To setup, follow steps 1~3 on page 26.
4. Press the ▲▼ buttons to select Analogue Channel List, then press OK
button.
Setup
>Move
sOk
rReturn
Channel List
eExit
12:00
Prog.
1
2
3
4
5
Ch
-----------
Name
----------------
6
---
----
Analogue Channel List
▲
• Swap : Select the channel you want to swap by pressing the ▲▼
buttons, then press the OK button.
Move the channel by press the ▲▼ buttons, then press the
OK button.
• Delete : Select the channel you want to delete by pressing the ▲▼
buttons, then press the CANCEL button.
▼
>Move
sSwap
Cancel
rReturn
English - 27
System Setup
Start
To tune-in new channels, the DVD Recorder has been provided with the
option Manual Scan where the channel data can be entered by user.
Digital Channel List
This function is possible in DVB-T mode only.
This function is used to edit the favourite channel list or remove the
channel.
DTV list
001 BBC ONE
002 NO Name CH
007 NO Name CH
030 CBBC Channel
040 BBC NEWS 24
051 BBCi
800 PARIS PREMIERE
To setup, follow steps 1~3 on page 26.
4. Press the ▲▼ buttons to select Digital Channel List, then press OK button.
Edit FAV
Remove
Page
5. To edit the current channel to the Digital Channel List, press the
RED(A) button.
To remove a channel from the Digital Channel List, press the YELLOW(C)
button. Press the OK button to watch that channel.
Return
Radio list
System Setup
001 BBC ONE
002 NO Name CH
M  Press OK button in the DVB-T view to display the Digital channel list.
007 NO Name CH
030 CBBC Channel
040 BBC NEWS 24
040 BBCI
040 PARIS PREMIERE
 Press FAV LIST button 5 times in the DVB-T view to display the
channel list.
Edit FAV
Remove
Page
 You can select RADIO mode by pressing the TV/RADIO button on
Return
the remote control.
This button used to toggle the TV and RADIO mode.
Digital Favourite Channel
This function is possible in DVB-T mode only.
You can immediately register the present channel to the
Digital Favourite Channel list.
Favorite DTV 1
001 NO Name CH
002 BBC NEWS 24
To setup, follow steps 1~3 on page 26.
Remove
4. Press the ▲▼ buttons to select Digital Favourite Channel, then press
OK button.
Add Current
Page
Return
5. To add the current channel to the Digital Favourite channels, press the
YELLOW(C) button.
To remove a favourite channel from the Digital Favourite channel list,
press the RED(A) button.
Press the OK button to watch that channel.
M  You can also operate this function by pressing the FAV LIST button
on the remote control.
 You can make Digital favourite channel up to 8. (TV favourite list: 4,
Radio favourite list:4)
Setting up the Features
12:00
Features
Title List
Timer
Edit
Disc
Setting
2. Press the ▲▼ buttons to select Setup, then press the OK button.
3. Press the ▲▼ buttons to select Features, then press the OK button.
Setup
>Move
sOk
rReturn
This function allows you to setup the Features setting.
1. With the unit in Stop mode, press the MENU button.
DVD Auto Chapter : 5 Min
Format DVD-RW
: VR
EZ Record
: Off
DVD Bilingual Rec. : Main
DVB-T Auto Subtitle : On
DivX Registration Code
eExit
4. Press the ▲▼ buttons to select the desired features options, then
press the OK button.
5. Press the ▲▼ buttons to select the desired item, then press the OK
button.
English - 28
DVD Auto Chapter
Timer
Edit
Disc
Setting
XCVKL
12:00
Features
Title List
DVD Auto Chapter : 5 Min
Off
Format DVD-RW
: VR5 Min
EZ Record
: Off15 Min
DVD Bilingual Rec. : Main
DVB-T Auto Subtitle : On
DivX Registration Code
DVD-SR275M only
Setup
>Move
sOk
rReturn
eExit
Title Menu
1. Press the ▲▼ buttons to select DVD Auto Chapter, then press the OK
button.
Prog. 6
May. 18. 2007, 08:14:39 SLP
sOk
2. Press the ▲▼ buttons to select Off, 5Min or 15Min, then press the OK
button.
• Off : No chapter mark is inserted.
• 5Min : Inserts chapter marks at approximately 5 minute intervals.
• 15Min : Inserts chapter marks at approximately 15 minute intervals.
<Page
Press the EXIT button to exit the menu.
3. Press the REC (•) button to start recording.
(See page 53 about how to set recording mode)
4. Press the STOP button to stop recording.
5. To display the created titles, finalise the disc (See page 75) and then
press the TITLE MENU button. The title menu will be displayed.
J  The DVD Auto Chapter function does not work during Timer
Recording or when you turn the power off.
12:00
Features
Title List
Timer
Edit
Disc
Setting
DVD Auto Chapter : 5 Min
Format DVD-RW
: VRVR
EZ Record
: OffVideo
DVD Bilingual Rec. : Main
DVB-T Auto Subtitle : On
DivX Registration Code
sOk
rReturn
Timer
Edit
Disc
Setting
eExit
12:00
Features
Title List
C
When inserting a unused DVD-RW disc, you can select a recording
format (VR mode or Video mode) according to your needs (Please refer
to page 75).
Setup
>Move
Format DVD-RW
• VR : Automatically formats the disc in VR mode
• Video : Automatically formats the disc in Video mode
EZ Record
DVD Auto Chapter : 5 Min
Format DVD-RW
: VR
EZ Record
: Off On
Off
DVD Bilingual Rec. : Main
DVB-T Auto Subtitle : On
DivX Registration Code
CVKL
(V mode)DVD-SR275M only
Setup
This function allows you initialise and Finalise a disc automatically.
>Move
sOk
rReturn
eExit
1. Press the ▲▼ buttons to select EZ Record, then press the OK button.
2. Press the ▲▼ buttons to select On, then press the OK button.
Press the EXIT button to exit the menu.
3. Insert a disc.
English - 29
System Setup
>Move
A DVD-Video consists of ‘Titles’ and ‘Chapters’.
When you record one programme, it makes one Title.
If you use this function, the Title will be divided into Chapters.
A recording(a title) is automatically divided into chapters by inserting
chapter markings at specifi ed intervals.
The markings are inserted while the recording is being made.
If the disc is new DVD-RW, It is initialised to V mode automatically.
4. Press the REC (•) button.
5. EZ Record function will automatically Finalise the disc under the
following conditions.
• When you press the OPEN/CLOSE button on your DVD Recorder
after recording on at least 30% of the disc. The tray will open after
the disc has been finalised.
• The above feature is available only when a DVD-RW(V)/-R(V)/+R disc is
inserted.
Unformatted Disc.
Formatting. Please wait.
M  If you select “off”, you must finalise the disc manually in the Disc
Setting menu. (see page 76)
 The length of Recording is different according to recording mode.
System Setup
(see page 53)
 When the EZ Record set to 'On', disc will be formatted to V mode
automatically although you select the VR mode in the Format
DVD-RW option.
Anynet+ (HDMI-CEC) (DVD-SR275M only)
12:29
Features
Title List
Timer
Edit
DV Dubbing
Disc
Setting
Setup
>Move
DVD Auto Chapter : 5 Min
Format DVD-RW
: VR
EZ Record
: Off
Anynet+ (HDMI CEC) : OnOn
Language Follow : OnOff
DVD Bilingual Rec. : Main
DVB-T Auto Subtitle : On
DivX Registration Code
sOk
rReturn
eExit
Anynet+ is a function that can be used to operate the recorder using a
Samsung TV remote control, by connecting the DVD Recorder to a
SAMSUNG TV using a HDMI Cable. (see page 20) .This is only available
with SAMSUNG TVs that support Anynet+.
1. Press the ▲▼ buttons to select Anynet+(HDMI-CEC), then press the OK
button.
Anynet+(HDMI-CEC) items will be displayed.
2. Press the ▲▼ buttons to select On, then press the OK button.
Using Anynet+(HDMI-CEC)
1. Connect the recorder with a Samsung TV and HDMI cable.
(See page 20)
2. Set the Anynet+(HDMI-CEC) to “On” on your DVD Recorder. (see above)
3. Set the Anynet+ function at your TV.
(See the TV instruction manual for more information.)
• You can operate the DVD Recorder by using TV remote control. (TV
buttons that can be used to control the DVD Recorder :
,
DVD-R
View TV
►
Select Device
►
Record
►
Menu on Device
►
Device Operation
►
Receiver
►
: Off
Move
Exit
and
,
buttons,
1
~
9
,
,
button)
• When you press Anynet+ button on the TV remote control, the OSD to
the left will appear.
►
Setup
,
,
Ok
TV Menu
- Select Device : Use this option to select device.
- Record : Use this option to start recording or stop recording.
- Menu on Device : Same as MENU button on the DVD Recorder remote
control.
- Device Operation : Same as ANYKEY button on the DVD Recorder
remote control.
M  By pressing the PLAY button of the recorder while watching TV,
the TV screen will change to the play screen.
English - 30
 If you play a DVD when the TV power is off, the TV will power On.
 If you turn the TV off, the DVD Recorder will power off
automatically. (When the DVD recorder is recording, it can’t be
powered off.)
 If you change the HDMI to other sources(Composite, Component,
RF... etc) in TV while playing the DVD disc, the DVD Recorder will
stop playing. But the DVD Recorder may keep the DVD disc playing
depending on navigation that the DVD disc supports.

Language Follow (DVD-SR275M only)
12:29
Features
Title List
Edit
DV Dubbing
Disc
Setting
Setup
>Move
sOk
rReturn
12:00
Features
Title List
Timer
Edit
Disc
Setting
eExit
DVD Auto Chapter : 5 Min
Format DVD-RW
: VR
EZ Record
: Off
DVD Bilingual Rec. : Main
Main
DVB-T Auto Subtitle : On Sub
DivX Registration Code
sOk
rReturn
• On
• Off
•
DVD Bilingual Rec.
Select the sound to be recorded on the disc.
This setting is not necessary when recording on DVD-RWs(VR mode)
that record both the main and sub sounds.
Setup
>Move
This sets the menu language of external devices connected to a
Samsung TV using Anynet +, so they match the language setting of
the TV. To activate this, Anynet+ (HDMI CEC) must be set to On.
eExit
• Main : Records the main sound for bilingual programmes.
• Sub : Records the sub sound for bilingual programmes.
DVB-T Auto Subtitle
12:00
Features
Title List
Timer
Edit
Disc
Setting
DVD Auto Chapter : 5 Min
Format DVD-RW
: VR
EZ Record
: Off
DVD Bilingual Rec. : Main
DVB-T Auto Subtitle : OnOn
DivX Registration Code Off
M  It is available when receiving the DVB-T that has a subtitle.
Setup
>Move
sOk
rReturn
• On : The subtitle is shown automatically when receiving the DVB-T.
• Off : The function is cancelled.
eExit

DivX Registration Code
12:00
Features
Title List
Timer
Edit
Disc
Setting
DivX Video On Demand.
Your registration code is : XXXXXXXX
To Iearn more visit www.divx.com/vod
Please use the Registration code to register this DVD Recorder with the
DivX Video On Demand format. For more information, visit www.divx.
com/vod.
Setup
>Move
sOk
rReturn
eExit
English - 31
System Setup
DVD Auto Chapter : 5 Min
Format DVD-RW
: VR
EZ Record
: Off
Anynet+ (HDMI CEC) : On
Language Follow : OnOn
DVD Bilingual Rec. : Main
Off
DVB-T Auto Subtitle : On
DivX Registration Code
Timer
Setting up the Options
Language
12:00
Language
Title List
Timer
Edit
Disc
Setting
OSD
Disc Menu
Audio
Subtitle
DVB-T Audio
DVB-T Subtitle
:
:
:
:
:
:
English
English
Original
Auto
English
English
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK button.
Setup
>Move
sOk
rReturn
If you set the language options, in advance, they will come up
automatically every time you watch a movie.
eExit
3. Press the ▲▼ buttons to select Options, then press the OK button.
4. Press the ▲▼ buttons to select Language, then press the OK button.
Language setup menu will be displayed.
System Setup
5. Press the ▲▼ buttons to select the desired language option, press the
OK button.
• OSD : For the on-screen menu of your DVD Recorder.
• Disc Menu : For the disc menu contained on the disc.
• Audio : For the disc audio language.
• Subtitle : For the disc subtitles.
• DVB-T Audio : For the current broadcasting Programme provides
audio.
• DVB-T Subtitle : For the current broadcasting Programme provides
subtitles.
6. Press the ▲▼ buttons to select the desired language, then press the
OK or ► button.
M  If the selected language is not recorded on the disc, the original
pre-recorded language is selected.
 The selected language will only appear if it is supported on the disc
and DVB-T.
 During the playback, press the SUBTITLE button to select DVD
subtitle. Because the default of DVD subtitle is off, press the
SUBTITLE button to select the desired subtitle.
Setting up the Parental
Timer
Language
Parental
Front Display
: Auto
The Parental function works in conjunction with DVDs and DVB-T that
have been assigned a rating which helps you control the types of DVDs
that your family watches. There are up to 8 rating levels on a disc.
Edit
Disc
Setting
Setup
>Move
Z
12:00
Options
Title List
sOk
rReturn
eExit
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK button.
3. Press the ▲▼ buttons to select Options, the press the OK button.
4. Press the ▲▼ buttons to select Parental, then press the OK button.
When you operate your DVD Recorder for the first time, the “Create the
Password” message will be displayed.
5. Enter the 4-digit password using the number buttons on the remote
control.
English - 32
The “Confirm the password” message will be displayed. Enter your
password again.
M  Press the RETURN button to return to the previous menu.
Press the EXIT ( ) button to exit the menu.
If you forgot your password
1. Remove the disc.
2. Press and hold the PLAY ( ) button on the front panel for 5 seconds
or more under no disc and DVD mode.
Tray is open and password will revert to factory settings.
12:00
Parental
Title List
Timer
Edit
Programme Grade
: Off
Off
Rating Level
: Off Grade 17
Change Password
Grade 16
Grade 15
Grade 14
Grade 13
Grade 12
Grade 11
Disc
Setting
Setup
>Move
sOk
rReturn
eExit
1. Press the ▲▼ buttons to select Program Grade, then press the OK
button.
2. Press the ▲▼ buttons to select the program grade you want, then
press the OK button.
For example, if you select up to 15, DVB-T that contain 16, 17 will not
display. A larger number indicates that the program is intended for
adult use only.
Setting the Rating Level
12:00
Parental
Title List
Timer
Edit
Disc
Setting
Setup
Programme Grade
: Off
Rating Level
: Off Level8(Adults)
Change Password
Level7
Level6
Level5
Level4
Level3
Level2
2. Press the ▲▼ buttons to select the Rating Level you want, then press
the OK button.
For example, if you select up to Level 6, discs that contain Level 7, 8 will not
play. A larger number indicates that the programme is intended for adult
use only.
▼
>Move
sOk
rReturn
1. Press the ▲▼ buttons to select Rating Level, then press the OK
button.
eExit
Changing the Password
12:00
Parental
Title List
Timer
Programme Grade
Rating Level
Change Password
: Off
: Off
2. Enter a new 4-digit password using the number buttons on the remote
control. The “Confirm the password” message will be displayed.
Edit
Disc
Setting
Setup
>Move
sOk
1. Press the ▲▼ buttons to select Change Password, then press the OK
button.
rReturn
eExit
3. Enter your new password again using the number buttons on the
remote control.
English - 33
System Setup
Setting the Program Grade
Setting up the Front Display
12:00
Options
Title List
Timer
Language
Parental
Front Display
Edit
Disc
Setting
: Auto
Auto
Bright
Dimmer
Off
Setup
>Move
sOk
rReturn
eExit
This function allows you to adjusts the lighting of the front panel
display.
• Auto : Adjusts to low lighting when power is off.
• Bright : Maintains bright lighting when power is off.
• Dimmer : Maintains low lighting regardless of whether power is on
or off.
• Off : Turn off the lighting when power is off.
Maintains the lighting when power is on.
Setting up the Video Options
12:00
System Setup
Setup
Title List
Timer
Edit
Disc
Setting
Tuner Preset
Clock Set
Video
Audio
Features
Options
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK button.
Setup
>Move
sOk
This function allows you to setup the video setting.
This function depends on disc type. It may not work for some disc types.
rReturn
eExit
3. Press the ▲▼ buttons to select Video, then press the OK button.
Video setup menu will be displayed.
4. Press the ▲▼ buttons to select the desired video option, then press
the OK button.
5. Press the ▲▼ buttons to select the desired item, then press the OK
button.
M  Press the RETURN button to return to the previous menu.
Press the EXIT (
) button to exit the menu.
TV Type
12:00
Video
Title List
Timer
Edit
Disc
Setting
TV Type
Picture Control
AV 1 Output
Component Out
Progressive
: 4:316:9
Letter Box
: Standard
4:3 Letter Box
: Video
4:3 Pan Scan
: On
: On
Depending on the type of television you have, you may want to adjust
the screen setting. (aspect ratio)
• 16:9 : You can view the full 16:9 picture on your wide screen TV.
• 4:3 Letter Box : Select when you want to see the total 16:9 ratio screen
DVD supplies, even though you have a TV with a 4:3
ratio screen. Black bars will appear at the top and
bottom of the screen.
Setup
>Move
sOk
rReturn
eExit
• 4:3 Pan Scan : Select this for conventional size TV when you want to see
the central portion of the 16:9 screen. (Extreme left and
right side of movie picture will be cut off.)
•
English - 34
Resolution(HDMI) (DVD-SR275M only)
12:00
Video
Title List
Timer
Edit
DV Dubbing
Disc
Setting
TV Type
: 4:3 Letter Box
Resolution(HDMI) : Auto
Auto
Video(HDMI)
: YCbCr
1920 x 1080p
1920 x 1080i
Picture Control
: Standard
1280 x 720p
AV 1 Output
: Video
Component Out
: On 720 x 576p
Progressive
: On
• Auto : It will be set to the possible maximum resolution supported by
the TV.
Setup
>Move
sOk
rReturn
This setting is used when the DVD Recorder is connected by HDMI or DVI
cable with Display devices(TV, projector, etc)
eExit
•
•
•
•
•
1920 x 1080p
1920 x 1080i
1280 x 720p
720 x 576p
Connect the DVD Recorder to your TV via HDMI or DVI cable. And set
your TV’s input to HDMI or DVI.
 Progressive scan automatically activates when HDMI is connected.
 There will be no HDMI video and audio outputs unless progressive
scan function is activated.
 Consult your TV User’s Manual to find out if your TV supports
Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual
regarding Progressive Scan settings in the TV’s menu system.
 If Video Output is set incorrectly, the screen may be blocked.
 The resolutions available for HDMI/DVI output depend on the
connected TV or projector. For details, see the user’s manual of your
TV or projector.
 When the resolution is changed it may take a few seconds for a
normal image to appear.
 If you set the HDMI output resolution 720p, 1080p or 1080i, HDMI
output provides better picture quality.
Video(HDMI) (DVD-SR275M only)
12:00
Video
Title List
Timer
Edit
DV Dubbing
Disc
Setting
TV Type
: 4:3 Letter Box
Resolution(HDMI) : Auto
Video(HDMI)
: YCbCr
YCbCr
Picture Control
: Standard
RGB
AV 1 Output
: Video
Component Out
: On
Progressive
: On
• YCbCr : Normally, select this when connecting to an HDMI device.
• RGB : Gives brighter colours and deeper black. Select this if colours are
weak.
Setup
>Move
This setting is used to select the type of output from the HDMI/OUT
jack.
sOk
rReturn
eExit
English - 35
System Setup
M  This function depends on disc type. It may not work for some discs.
Picture Control
12:00
Video
Title List
Timer
Edit
Disc
Setting
TV Type
Picture Control
AV 1 Output
Component Out
Progressive
: 4:3Dynamic1
Letter Box
: Standard
Dynamic2
: Video
Standard
: OnCinema1
: OnCinema2
Personal
Setup
Selects the picture control for the video signals output from the
AV output jacks.
You can adjust the DVD video signal from the recorder to obtain the
picture quality you want.
Select the setting that best suits the programme you are watching.
• Dynamic 1 : Produces a bold dynamic picture by increasing the picture
>Move
sOk
rReturn
contrast and the colour.
eExit
• Dynamic 2 : Produces a more dynamic picture than “Dynamic 1” by
further increasing the picture contrast and the colour.
• Standard : Displays a standard picture (function turned off ).
• Cinema 1 : White colours become brighter and black colours become
richer,and the colour contrast is increased.
System Setup
• Cinema 2 : Enhances detail in dark areas by increasing the black level.
• Personal : Adjusts Contrast, Brightness, Colour and Hue using ▲▼◄►
buttons.
M  This function can only be used when you have the Video Out
(AV out) jacks connected and does not work with Component and
HDMI.
AV1 Output
12:00
Video
Title List
Timer
Edit
Disc
Setting
TV Type
Picture Control
AV 1 Output
Component Out
Progressive
: 4:3 Letter Box
: Standard
Video
: Video
: OnRGB
You can enjoy high quality image through Video or RGB connections.
Only one of these signals can be selected at one time.
• Video : Video output is available connecting component (Y, PB, PR) or
: On
scart jack(AV1)
Setup
• RGB : RGB video output is available connecting scart jack(AV1). When
>Move
sOk
rReturn
you set “AV 1 Output” to “RGB”, you should set “Component Out”
and “Progressive” to “Off ”.
eExit
Component Out
12:00
Video
Title List
Timer
Edit
Disc
Setting
TV Type
Picture Control
AV 1 Output
Component Out
Progressive
Selects whether or not to output video signals from the COMPONENT
VIDEO OUT jacks.
: 4:3 Letter Box
: Standard
: Video
: On On
: On Off
• On : Outputs the component video signals. Select this when you want
to view progressive signals.
Setup
• Off : Outputs no signals.
>Move
sOk
rReturn
eExit
Progressive
12:00
Video
Title List
Timer
Edit
Disc
Setting
TV Type
Picture Control
AV 1 Output
Component Out
Progressive
: 4:3 Letter Box
: Standard
: Video
: On
: On On
Off
Setup
>Move
sOk
rReturn
eExit
This function is available when video output is component. This
setting enables you to select a desired progressive mode. To view
“Progressive scan mode”, first connect the component cable. (See
page 20) Be sure the Component cables are connected properly.
• On
• Off
M  When the HDMI cable (not supplied) is connected, “Off” can not be
selected.
 Progressive setting is only available when the Recorder is in stop mode.
English - 36
Setting up the Audio Options
12:00
Setup
Title List
Timer
Edit
Disc
Setting
Tuner Preset
Clock Set
Video
Audio
Features
Options
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Setup, then press the OK button.
3. Press the ▲▼ buttons to select Audio, then press the OK button.
Setup
>Move
sOk
This function allows you to setup the Audio options.
rReturn
eExit
4. Press the ▲▼ buttons to select the desired audio option, then press
the OK button.
5. Press the ▲▼ buttons to select the desired item, then press the OK
button.
M  Press the RETURN button to return to the previous menu.
Press the EXIT (
) button to exit the menu.
Title List
Timer
Edit
Disc
Setting
Digital Out
Downmix
Audio DRC
Scan Audio
Surround
AV Audio Input
: OnOn
: Dolby
Off Surround
: Standard
: On
: Off
: Stereo
Selects audio options of signals output from the DIGITAL AUDIO OUT
(COAXIAL).
• On : Normally select this.
Press the OK button and select “Dolby Digital,” “DTS,” or “MPEG”
for further settings.
Setup
>Move
sOk
rReturn
Dolby Digital
DTS
MPEG
: D-PCM
: Off
: PCM
12:00
Digital Out
Title List
Timer
eExit
Edit
• Off : The influence of the digital circuit upon the analogue circuit is
minimum.
The following setup items switches the method of outputting audio
signals when you connect a component such as an amplifier (receiver)
with a digital input jack.
For connection details, see "AV Receiver Connections" on page 22.
Disc
Setting
M  If you connect a component that does not accept the selected
Setup
>Move
sOk
rReturn
audio signal, a loud noise (or no sound) will come out from the
speakers, and may affect your ears or cause speaker damage.
eExit
‹ Dolby Digital (DVDs only)
Selects the type of Dolby Digital signal.
• D-PCM : Select this when the recorder is connected to an audio
•
component that does not have a built in Dolby Digital
decoder.
Dolby Digital : Select this when the recorder is connected to an audio
component with a built-in Dolby Digital decoder.
‹ DTS (DVD VIDEOs only)
Selects whether or not to output DTS signals.
• On : Select this when the recorder is connected to an audio
component with a built-in DTS decoder.
• Off : Select this when the recorder is connected to an audio
component without a built-in DTS decoder.
‹ MPEG (DVD VIDEOs only)
Selects the type of MPEG audio signal.
• PCM : Select this when the recorder is connected to an audio
•
component without a built-in MPEG decoder. If you play MPEG audio
sound tracks, the recorder outputs stereo signals.
MPEG : Select this when the recorder is connected to an audio
component with a built-in MPEG decoder.
English - 37
System Setup
Digital Out
12:00
Audio
Downmix (DVDs only)
12:00
Audio
Title List
Timer
Edit
Disc
Setting
Digital Out
Downmix
Audio DRC
Scan Audio
Surround
AV Audio Input
: On
: Dolby
Surround
Dolby
Surround
: Standard
Normal
: On
: Off
: Stereo
• Dolby Surround : Select this setting to enjoy Multi-channel DVDs over
Setup
>Move
Switches the method for mixing down to two channels when you play a
DVD which has rear sound elements (channels) or is recorded in Dolby
Digital format.
two channels.
sOk
rReturn
eExit
• Normal : Multi-channel audio signals are downmixed to two channels
for use with your stereo.
M  To enjoy the surround effect of Dolby Digital, turn off the
System Setup
surround settings of this recorder.
Audio DRC (Dynamic Range Control) (DVDs only)
12:00
Audio
Title List
Timer
Edit
Disc
Setting
Digital Out
Downmix
Audio DRC
Scan Audio
Surround
AV Audio Input
• Standard : Normal setting.
• TV Mode : Makes low sounds clear even if you turn the volume down.
• Wide Range : Gives you the feeling of being at a live performance.
: On
: Dolby Surround
: Standard
Standard
: On TV Mode
: Off Wide Range
: Stereo
Setup
>Move
sOk
rReturn
Makes the sound clearer when the volume is turned down when playing
a DVD that conforms to Audio DRC.
eExit
Audio(HDMI)(DVD-SR275M only)
Selects the output method from the HDMI OUT jack.
12:00
Audio
Title List
Timer
Edit
DV Dubbing
Disc
Setting
Setup
>Move
Digital Out
Downmix
Audio DRC
Audio(HDMI)
Scan Audio
Surround
DV Audio Input
AV Audio Input
sOk
: On
: Dolby Surround
: Standard
: Auto
Auto
: OnPCM
: Off
: Stereo1
: Stereo
rReturn
Timer
Edit
Disc
Setting
the connected HDMI device. If the HDMI OUT jack is connected to
equipment not compatible with Dolby Digital, PCM will
automatically be output, even when “Dolby Digital” is selected.
• PCM : Converts all audio signals to Linear PCM.
eExit
12:00
Audio
Title List
Digital Out
Downmix
Audio DRC
Scan Audio
Surround
AV Audio Input
: On
: Dolby Surround
: Standard
: On On
: OffOff
: Stereo
sOk
rReturn
Scan Audio (DVDs only)
• On : Outputs audio signals during FF1 fast-forward of a DVD disc with
Dolby Digital soundtracks.
• Off : Turns off the function. No sound is output during FF1 fast-forward.
Setup
>Move
• Auto : Normal setting. Outputs audio signals according to the status of
eExit
M  Sound will be interrupted during Scan Audio.
 If the audio format is LPCM, this function is not supported.
English - 38
Surround
12:00
Audio
Title List
Timer
Edit
Disc
Setting
Digital Out
Downmix
Audio DRC
Scan Audio
Surround
AV Audio Input
Setup
: On
: Dolby Surround
: Standard
: On Off
: Off Surround1
: Stereo
Surround2
Turns on the surround function to create virtual rear speakers from a
stereo TV or two separate front speakers.
• Off : No surround effect
• Surround 1 : Creates one set of virtual surround speakers.
• Surround 2 : Creates two sets of virtual surround speakers.DV Audio
Surround3
Input
>Move
sOk
rReturn
eExit
• Surround 3 : Creates three sets of virtual surround speakers.
M  When the playback signal does not contain surround audio signals,
the surround effects will not be heard.
 When you select one of the surround modes, turn off the surround
DV Audio Input (DVD-SR275M only)
12:00
Audio
Title List
Timer
Edit
DV Dubbing
Disc
Setting
Setup
>Move
Digital Out
Downmix
Audio DRC
Audio(HDMI)
Scan Audio
Surround
DV Audio Input
AV Audio Input
sOk
: On
: Dolby Surround
: Standard
: Auto
: On
: OffStereo1
: Stereo1
Stereo2
: Stereo
Mix
rReturn
• Stereo 1 : Records original sound only.
Normally select this when dubbing a DV format tape.
• Stereo 2 : Records additional audio only.
• Mix : Records both original and additional sounds.
eExit
M  Select “Stereo 2” or “Mix” if you have added a second audio channel
when recording with your digital video camera.
AV Audio Input
12:00
Audio
Title List
Timer
Edit
Disc
Setting
Digital Out
Downmix
Audio DRC
Scan Audio
Surround
AV Audio Input
: On
: Dolby Surround
: Standard
: On
: Off Stereo
: Stereo
Bilingual
• Stereo : Records stereo sound only.
• Bilingual : You can record audio from two different sources on the left and
Setup
>Move
sOk
rReturn
When recording from equipment connected to the AV input jacks to a DVD
disc in this recorder, select AV input audio.
eExit
right channels with DVD-RWs/(VR mode) and DVDRs/(VR mode).
You can select either the Main(left) or Sub(right) soundtrack
when playing back. Please refer to the AUDIO button. (See page
46).
English - 39
System Setup
settings of the connected TV or amplifier (receiver).
DTV Functions
Basic Functions
Display Screen
DVD-VIDEO
INFO
TF1
Time
Audio
Video
Signal Info
>MOVE
: 15:05:00
: FRA
: 4:3
: 94%
>CHANGE
After the television channels have been stored, you will see the following
picture(banner) each time you switch channels.
You can use this function when you see DVB-T.
1. Press the
button once to display the channel and the channel name.
2. Select the channel by pressing the NUMBER buttons or PROG (
buttons to move to TV channel.
You will also see this banner each time you change channels.
/
)
DVD
DTV Functions
DTV
TF1
800
➀ ➁ ➂ ➃
◆ Banner Elements
1. Displays the favourite channel.
2. Displays the Digital text (MHEG).
3. Displays the subtitle.
4. Displays the multi audio.
M  The icon is displayed according to the service information of signal.
 The icon is displayed only with more than one audio type and
language.
Select Audio Track
1. Press the AUDIO button to see the Audio track list.
2. Press the ▲▼ buttons to select desired Audio track, then press the OK
button.
Audio Track ENG MPEG
>Change
English - 40
Setting the Favourite Channel
You can immediately register the present channel to the Digital Favourite
Channel List.
Favorite DTV 1
1. Press the FAV LIST button while you are viewing a programme.
001 NO Name CH
002 BBC NEWS 24
Remove
Page
2. To add the current channel to the Digital Favourite channels, press the
YELLOW (C) button.
(To display all favourite list, press the FAV LIST button. Each time FAV LIST
button is pressed, favourite list will be toggled.)
To remove a favourite channel from the Digital Favourite channel list, press the
RED(A) button.
Add Current
Return
– To watch the favourite channel –
Press the FAV LIST button and then select the channel.
Press the OK button to watch that channel.
M  You can make up to 8 Digital favourite channel. (TV favourite list:
4, Radio favourite list:4)
1. Press the SUBTITLE button.
2. Press the ▲▼ buttons to select a desired subtitle, then press the OK
button.
>Change
Using the digital text service
B B C
i
100
Wednesday 3 Aug
News Multiscreen
News Headlines
Sport
Weather
Finance
BBCi INDEX
Today on BBCi
Today's regional headlines
from BBC News . 160
Press TEXT to exit
1001
When the current broadcasting programme provides digital text service, you
can use digital text service.
101
300
400
200
199
1. Press the TEXT button, the main menu of digital text will be displayed.
2. Press the ▲▼ or number button to select desired digital text, then press
the OK button.
M  Press the EXIT button to exit the main menu of digital text.
 Press the TEXT button to exit the digital text mode.
English - 41
DTV Functions
Changing the Subtitle Language
When the current broadcasting programme provides subtitle, press the
SUBTITLE button . If Subtitle is available on current programme, menu bar is
displayed on the upper side.
Subtitle ENG
Guide
DTV Guide
12:00 TUE 1 JAN 2008
The electronic programme guide gives you a channel list for the
channels.
12:00 - 12.25 Blue Peter
TUE 1 JAN
001
BBC ONE
002
BBC TWO
007
CBBC Channel
030
CBBC Channel
040
BBC NEWS 24
001
BBCi
A
12:30
Blue Peter
13:00
---
Neighbours
Basli Brush
Tracy
Beake
---
13:30
Look North
BBC News
Beg. Borrow or Steal Strictly Come Dancing: It T
The Weekest Link
---
Blue Peter
Out There
BBC News
BBC News
BBCi
BBCi
---
Timer Rec
PREVIOUS/NEXT DAY
INFO
INFORMATION
1. Press the GUIDE button while you are viewing a programme. (DTV)
• RED(A) button (Timer Record) : Setting the Timer Record.
• (►►l)button : Go to next day
• (l◄◄)button : Go to previous day
→ It displays programme from now to 8 days after.
• ▲▼◄► button : select the programme and station.
• INFO button (Information) : View the detail information
M  The contents of cell could be displayed with a delay according to the
broadcasting.
 If 'Daylight Saving Time' and 'GMT Time' settings are wrong, EPG Time
DTV Functions
will be incorrect.
Guide Timer Recording
DTV Guide
12:00 TUE 1 JAN 2008
12:00 - 12.25 Blue Peter
TUE 1 JAN
001
BBC ONE
002
BBC TWO
007
CBBC Channel
030
CBBC Channel
040
BBC NEWS 24
001
BBCi
A
12:30
Blue Peter
13:00
---
Neighbours
Basli Brush
Tracy
Beake
---
13:30
Look North
BBC News
Beg. Borrow or Steal Strictly Come Dancing: It T
The Weekest Link
---
Blue Peter
Out There
BBC News
BBC News
BBCi
BBCi
---
INFO
1. Press the ▲▼◄► buttons to select desired programme, then press RED(A)
button.
2. The time of Guide is the time of the current channel enters.
3. You can check the setting in the scheduled List. (see pages 71~72)
Timer Rec
PREVIOUS/NEXT DAY
Make sure that clock must be set before operating this function.
(see pages 23~24)
INFORMATION
M  The title information is displayed in the Title List as for Guide REC.
DTV Guide
12:00 TUE 1 JAN 2008
12:00 - 12.25 Blue Peter
TUE 1 JAN
12:30
Peter
TimerBlue
Rec
001
BBC ONE
002
BBC TWO
007
CBBC
030
CBBC
040
BBC NEWS 24
001
BBCi
A
---
13:00
Neighbours
Look North
Beg. Borrow or Steal Strictly Come Dancing: It T
The Weekest Link
---
13:30
BBC News
Do you want to reserve this event?
REC
Hubert son Altesse Cani
Yes
Tracy
No
BBC
 If Timer Rec is set, the icon is displayed in the set programme.
 If you press RED(A) button, timer recording will be cancelled.
 Up to 12 recording are possible including guide recording and
general recording.
---
BBCi
Timer Rec
PREVIOUS/NEXT DAY
INFO
INFORMATION
English - 42
Playback
This section introduces basic functions of playback and
playback by disc type.
Read the following information before playing a disc.
Disc types that can be played
Disc Types
Recorded content
Disc Shape
Single sided(12cm)
Region code (DVD-Video only)
DVD-VIDEO
Both the DVD Recorder and the discs are coded
by region. These regional codes must match in
order for the disc to play. If the codes do not
match, the disc will not play. The Region
Number for this DVD Recorder is described on
the rear panel of the DVD Recorder.
AUDIO VIDEO
Double sided(12cm)
Single sided(8cm)
Double sided(8cm)
AUDIO-CD
JPEG
MP3
Logos of Discs that can be played
Disc Logo
content
MPEG4
AUDIO
JPEG Image
MP3 Audio
MPEG4 Movie
Single sided(12cm)
Single sided(8cm)
Single sided(12cm)
Single sided(8cm)
Single sided(12cm)
Single sided(8cm)
Single sided(12cm)
Single sided(8cm)
Single Layer(12cm)
(4.7GB)
DVD-RAM
AUDIO VIDEO
Dual Layer(12cm)
(8.5GB)
Dolby Digital
DTS
Digital Audio
Stereo
PAL broadcast
system in U.K, France,
Germany, etc.
12cm
(4.7GB)
Single Layer(12cm)
(4.7GB)
DVD-R
DivX
AUDIO VIDEO
AUDIO VIDEO
Dual Layer(12cm)
(8.5GB)
MP3
DVD+RW
AUDIO VIDEO
12cm (4.7GB)
Single Layer(12cm)
(4.7GB)
DVD+R
CD-R/-RW/
DVD-RAM/
-RW/-R
English - 43
AUDIO VIDEO
JPEG
MP3
DivX
Dual Layer(12cm)
(8.5GB)
–
Playback
DVD-RW
Discs that cannot be played
• DVD-Video with a region number other than “2” or “ALL”
• 3.9 GB DVD-R Disc for Authoring.
• A DVD-RW(V)/DVD-R(V)/+R disc which has been recorded and not
finalised in a different manufacturer’s recorder.
• DVD-ROM/PD/MV-Disc, etc
• VCD/SVCD/CVD/CD-ROM/CDV/CD-G/CD-I
• BD, HD-DVD
M  This DVD Recorder can only operate with discs that are compatible
with DVD-RAM Standard Version 2.0.
 Playback and/or recording may not work for some types of discs, or
when specific operations, such as angle change and aspect ratio
adjustment, are being performed. Information about the discs is
written in detail on the box. Please refer to this if necessary.
 Do not allow the disc to become dirty or scratched, finger prints,
dirt, dust, scratches or deposits of cigarette smoke on the recording
surface may make it impossible to use the disc for recording.
 DVD-RAM/±RW/±R discs may not be able to play on some DVD
players, depending on the player, disc and the condition of the
recording.
 Discs with NTSC programmes recorded on them can be played but
Playback
cannot be recorded using this product.
Playing a Disc
1. Press the OPEN/CLOSE button.
2. Place a disc gently into the tray with the disc’s label facing up.
3. Press the OPEN/CLOSE button to close the disc tray.
• The DVD Recorder does not play discs automatically after being
powered on initially.
• When the DVD Recorder is powered on and a disc is in the tray, the
unit will be activated and wait in stop status.
• Press the PLAY( ) button to start playback.
4. Press the STOP(
) button to stop playback.
M  When you stop playing back a disc, the DVD Recorder remembers
where you stopped, so when you press PLAY( ) button again, it
will pick up where you left off. (Unless the disc is removed or the
DVD Recorder is unplugged, or if you press the STOP( ) button
twice.)
J  Do not move your DVD Recorder while playing, as this may cause
damage to the disc.
 Make sure to press the OPEN/CLOSE button to open or close the disc tray.
 Do not push the disc tray while it is being opened or closed, as this
may cause a product malfunction.
English - 44
 Do not place foreign materials on or in the disc tray.
 Some functions may perform differently or be disabled depending
on the disc type.
If this occurs, refer to the instructions written on the disc case.
 Be especially careful that children’s fingers are not caught between
the disc tray and the tray chassis when it closes.
 After turning power on, it will take a few seconds until the DVD
Recorder operates.
Using the Disc Menu & Title Menu
Some type of discs contain a dedicated menu system that allows you to
select special functions for title, chapter, audio track, subtitle, film
preview, information on characters, etc.
For DVD-VIDEO Disc
Z
• Disc Menu : Press the DISC MENU button to enter the disc menu of the
disc.
• Move to the setup menu related to playback operation.
• You can select audio language and subtitle etc. provided by the disc.
• Title Menu : Press the TITLE MENU button to move to the title menu of
For DVD-RAM/±RW/±R Disc
XCVKL
• Title List
Press the TITLE LIST button. Title List is a list of previously recorded
programmes. If a title is deleted, that title cannot be played again.
• Play List (DVD-RAM/-RW(VR)/-R(VR))
Press the PLAYLIST button. A playlist is a custom-made list of titles.
When one playlist is played, only the titles within the playlist will play
and then stop. Even if that playlist is deleted, the original recording will
not be deleted.
English - 45
Playback
the disc.
• Use this button if the disc contains more than one title.
• Some discs may not support the title menu functionality.
Using the playback related buttons
Searching through a Chapter or Track
ZXCVBKLD
During play, press the SEARCH (
) buttons on the remote control.
DVD-VIDEO/DVD-RAM/
±RW/±R
 FF1  FF2  FF3
 FR1  FR2  FR3
DivX
 FF1  FF2  FF3
 FR1  FR2  FR3
AUDIO CD
(CD-DA)
 FF1  FF2
 FR1  FR2
• You can scan the programme in reverse.
• To return to normal speed playback, press the PLAY( ) button.
M  You can hear sound during forward search (FF1) in DVD-VIDEO/
DVD-RAM/±RW/±R disc.
 The speed marked in this function may be different from the actual
playback speed.
Playback
Skipping Chapters, Titles or Markers
XCVBKL
During play, press the SKIP (
) buttons on the remote control.
• If you press the SKIP ( ) button,
it moves to the beginning of the chapter or Title or marker
Pressing the button once again within 3 seconds returns to the beginning of
the previous chapter or Title or marker (DVD-RAM/-RW(VR mode))
• If you press the SKIP ( ) button,
it moves to the next chapter or track .(DVD-RAM/-RW(VR mode)).
Slow Motion Play
ZXCVKLDD
In pause mode, press the SEARCH (
) buttons on the remote control.
• If you press the SEARCH ( ) button,
 Slow 3  Slow 2  Slow 1
• If you press the SEARCH ( ) button,
 Slow 3  Slow 2  Slow 1
• To return to normal speed playback, press the PLAY( ) button.
M  Slow motion can play only in the forward direction on MPEG4 discs.
English - 46
Using the ANYKEY button
Title 2/6
Chapter 2/12
Time 00:00:52
Audio ENG Dolby D 2ch(1/1)
Remain 00:00:52
Subtitle 1/1 ENG
Angle 1/1
<Adjust
sOk
The ANYKEY functions allows you to easily search for a desired
scene by accessing title, chapter, track and time. You can also
change the subtitle and audio settings and set some features
including Angle.
Moving to a desired scene directly
ZXCVKLD
If you want to move to a certain title, chapter or time, use this function.
1. Press the ANYKEY button during playback.
2. Press the ▲▼ buttons to select Title, Chapter or Time.
3. Press the ◄► buttons or number (0~9) buttons to select the desired
scene.
(When searching a time, enter the time in the sequence of hours,
minutes, seconds using the number buttons.)
Then, press the OK button.
M  This may not work for some discs. When an audio CD (CDDA) or an
MP3 disc is inserted, according to the disc type, the information
display may not be appear.
 The Time Search function does not operate on some discs.
 To make the sub-menu disappear, press the ANYKEY or RETURN
Playback
button again.
Selecting the Audio language
Title 2/6
Chapter 2/12
Time 00:00:52
Audio ENG Dolby D 2ch(1/1)
Remain 00:00:52
Subtitle 1/1 ENG
Angle 1/1
<Adjust
sOk
ZD
Audio languages may not work depending on the disc type. This is
only available during playback.
You can also operate this function by pressing the AUDIO button on
the remote control.
1. Press the ANYKEY button during playback.
2. Press the ▲▼ buttons to select Audio, then press the ◄► buttons to
select the desired audio language.
3. Press the OK button.
M  Audio languages may be different because they are disc-specific.
 Some discs allow you to select the audio language for the disc
menu only.
 To make the sub-menu disappear, press the ANYKEY or RETURN
button again.
English - 47
Remain
You can check the remaining time of the current title.
1. Press the ANYKEY button during playback.
Title 2/6
Chapter 3/12
Time 00:00:52
Audio ENG Dolby D 2ch(1/1)
Remain 00:00:52
Subtitle 1/1 ENG
Angle 1/1
>Move
sOk
Selecting the Subtitle Language
ZD
Title 2/6
Chapter 3/12
Time 00:00:52
Audio ENG Dolby D 2ch(1/1)
Remain 00:00:52
Subtitle 1/1 ENG
Angle 1/1
<Adjust
sOk
Subtitle languages may not work depending on the disc type. This
is only available during playback.
You can also operate this function by pressing the SUBTITLE button
on the remote control.
1. Press the ANYKEY button during playback.
2. Press the ▲▼ buttons to select Subtitle, then press the ◄► buttons
to select the desired subtitle language.
3. Press the OK button.
Playback
M  The subtitle display may be different depending on the disc type.
 Some discs allow you to select the language for the disc menu only.
 To make the sub--menu disappear,press the ANYKEY or RETURN
button again.
Changing the Camera Angle
Z
Title 2/6
Chapter 3/12
Time 00:00:52
Audio ENG Dolby D 2ch(1/1)
Remain 00:00:52
Subtitle 1/1 ENG
Angle 1/1
<Adjust
sOk
If a DVD-VIDEO contains multiple angles of a particular scene, you can
use the Angle function.
If the disc contains multiple angles, the A appears on the screen.
1. Press the ANYKEY button during playback.
2. Press the ▲▼ buttons to select Angle, then press the ◄► buttons or
number (0~9) buttons to select the desired angle scene.
3. Press the OK button.
M  This function is disc-dependent, and may not work all DVDs.
 This function does not work when a DVD has not been recorded
with a multi-camera angle system.
 To make the sub-menu disappear, press the ANYKEY or RETURN
button again.
English - 48
Playing an Audio CD/MP3
Buttons on the Remote Control used for Audio
CD(CD-DA)/MP3 playback
4
3
5
5
7
8
2. OK button : Plays the selected track (song).
6
3. SKIP (
) button : Moves to the next track.
4. SKIP (
) button : Moves to the previous track.
1
1. ▲▼ : Selects a track (song).
5. Press the SEARCH (
Reverse scan : FR
2
) buttons : Forward scan : FF,
6. PLAY ( ) button : Plays a track(song).
7. STOP (
8. PAUSE (
) button : Stops a track(song).
) button : Pauses Playback.
To Playback, press the PLAY button.
Playing an Audio CD(CD-DA)
1. Insert an audio CD (CD-DA) into the disc tray.
• The audio CD menu appears and the tracks (songs) are played
➀
➁
◆ Audio CD(CD-DA) Screen Elements
12:00
Music
Surround : Off
➃
➄
Q TRACK01.CDA
9 1/15
>Move
Play
00:00:19
➂
q9 TRACK01.CDA
9 TRACK02.CDA
9 TRACK03.CDA
9 TRACK04.CDA
9 TRACK05.CDA
9 TRACK06.CDA
➀ Current track (song) : Displays the number of the track currently being
played.
➁ This shows the operating state of a disc and a playback time corresponding
to a portion that is currently played.
sOk
➂ Display the track list (song list).
eExit
➃ Display the current file.
➄ Display available buttons.
Playing an MP3 Disc
➀
1. Insert an MP3 disc into the disc tray.
• The menu is displayed
➁
2. Press the ▲▼ buttons to select Music, then press the OK button.
12:00
Music
Surround : Off
➃
➄
Q SONG01.MP3
E/
9 1/15
>Move
Play
00:00:19
➂
q9 SONG01.MP3
9 SONG02.MP3
9 SONG03.MP3
9 SONG04.MP3
9 SONG05.MP3
9 SONG06.MP3
sOk
rReturn
3. Press the ▲▼ buttons to select the track you want to hear, and then
press the OK button.
◆ MP3 Screen Elements
eExit
➀ Current track (song) : Displays the number of the track currently being
played.
English - 49
Playback
automatically.
2. Press the ▲▼ buttons to select the track (song) you want to hear,
and then press the OK button.
➁ This shows the operating state of a disc and a playback time corresponding
to a portion that is currently played.
➂ Displays the track list (song list).
➃ Displays the current file.
➄ Displays available buttons.
M  If select the Music, MP3 files will only be displayed.
 If there are no MP3 files, empty folder will only be displayed.
Playing back a Picture Disc
G
12:00
Photo
Picture 1 / 10
Slideshow
1. Insert a JPEG Disc into the disc tray.
Page 1 / 2
mMove
sOk
rReturn
Stop
12:00
Photo
Picture 1 / 10
Slideshow
Playback
Slideshow Speed
Page 1 / 2
<Adjust
sOk
rReturn
2. Press the ▲▼ buttons to select the Photo, and then press the OK
button.
3. Press the ▲▼◄► buttons to select a picture.
• To see the next 6 pictures, press the $ button.
• To see the previous 6 pictures, press the # button.
4-1. If you press the PLAY ( ) button, the Slide Show Speed screen will
appear.
Press the ◄► buttons to set the slide show speed, then press the OK
button.
4-2.Press the OK button with a picture selected in the Album screen and select
a display mode (Album screen ( ), Slide show ( ), Rotation ( ), or
Zoom ( )) using the ◄► buttons, then press the OK button.
: Returns to the Album screen.
DVD-RW(VR)
: The unit enters slide show mode.
Before the slide show begins the picture interval (Slide show speed) must
be set.
: Each time the OK button is pressed, the picture rotates 90 degrees
clockwise.
JPEG01.JPG
<Move
sOk
rReturn
Anykey
: Each time the OK button is pressed, the picture is enlarged up to 4X(Four
times the normal size).
Normal g Zoom X2 g Zoom X4 g Zoom X2 g Normal.
• Press the ANYKEY button to display the menu bar.
• Press the ANYKEY button again to clear the menu bar.
M  If select the Photo, JPEG files will only be displayed.
 If there are no JPEG files, empty folder will only be displayed.

Music/Photo Simultaneous Playback
1. Insert a Mixed disc(Music+JPEG) into the disc tray.
2. Press the ▲▼ buttons to select the MIX, and then press the OK
button.
The track list will be displayed.
English - 50
12:00
Music
Q SONG01.MP3
Play
00:00:19
q9 SONG01.MP3
9 SONG02.MP3
Do you
want to view
9 SONG03.MP3
the photo
with MP3?
9 SONG04.MP3
9
SONG05.MP3
Yes
No
9 SONG06.MP3
E/
9 1/15
>Move
sOk
3. Press the OK button.
The message “Do you want to view the photo with MP3?” will be
displayed.
4. Press the ◄► button to select Yes, then press the OK button. You can
listen to the music while watching the photo.
M  To operate this function, you have to select the disc containing
rReturn
both music files and photo file.
eExit
Playing an MPEG4 Disc
File
Stop
E/
1/2
D
12:00
DivX
Album
00:00:19
3 DIVX01.AVI
3 DIVX02.AVI
1. Insert an MPEG4 disc into the disc tray.
• The menu is displayed
2. Press the ▲▼ buttons to select DivX, then press the OK button.
>Move
sOk
rReturn
eExit
3. Press the ▲▼ buttons to select the avi file (DivX), then press the OK or
PLAY ( ) button.
4. When DivX file is played, you can use following functions. Pressing the
STOP ( ) button once during playback will display the file list,
pressing the button again will exit the menu screen.
MPEG4 Function Description
Function
Description
During play, press the SKIP (
it moves previous or next track.
Search
) buttons and
During play, press the SEARCH (
press again to search at a faster speed.
(FF1, FF2, FF3)
Slow Motion Play
In pause mode( ), press the SEARCH ( ) button
on the remote control. (Slow3, Slow2, Slow1)
Reverse Slow Motion Play is not available.
) buttons,
M  This unit can play the following video compression formats,
- DivX Video (Codec) Format : DivX 3.11 DivX 4.x DivX 5.x (without
QPEL and GMC)
- DivX Audio (Codec) Format : MP3, MPEG1 Audio Layer 2, LPCM,
AC3
 Supported subtitle file formats: .smi, .srt, .sub, .psb, .txt, .ass (The
subtitle file should have exactly the same name to corresponding
DivX file name)
 Some DivX files created on a personal computer may not be play
back. That is why Codec Type, Version and Higher resolution over
specification are not supported.
 You cannot play back the disc that is larger than a 720 x 576 pixel
resolution.
English - 51
Playback
Skip
Recording
This section shows various DVD Recording & VCR
methods.
This unit can record on various types of discs.
Before recording, read the following instructions and
select the disc type according to your preference.
Compatibility between Samsung and
Other Company’s Recorder
• X : not possible
Disc
Types
Rec.
format
DVD-RAM
VR
Mode
Recordable Discs
This DVD Recorder can record on the following discs.
• DVD-SR270M
DVD-RAM
DVD-R
Finalising
Samsung
X
Recordable
Other
Company
X
Recordable
DVD-RW
Samsung
VR
Mode
• DVD-SR275M
DVD-RAM
DVD-R
DVD-RW
DVD+RW
DVD+R
Other
Company
DVD-RW
Samsung
V
Mode
• DVD±RWs and DVD-RAMs are rewritable.
• DVD±Rs are non-rewritable.
Other
Company
Samsung
V
Mode
Recording
DVD-R
Other
Company
DVD+RW
-
Not recordable
not
finalised
Recordable
finalised
Not recordable
not
finalised
Recordable
finalised
Not recordable
not
finalised
Recordable
finalised
Not recordable
not
finalised
Not recordable
finalised
Not recordable
not
finalised
Recordable
finalised
Not recordable
not
finalised
Not recordable
X
Recordable
Other
Company
X
Not recordable in
some cases
finalised
Not recordable
not
finalised
Not recordable
in some cases
finalised
Not recordable
not
finalised
Not recordable in
some cases
Other
Company
M  Finalise
finalised
Samsung
Samsung
DVD+R
Additional
Recording in
Samsung Recorder
Recording
Device
- This closes the DVD±RW/±R so no additional
recording can be done.
- The DVD-RAM/+RW disc cannot be finalised.
English - 52
 Unfinalise
- This allows additional recording on a DVD-RW disc originally
recorded on the DVD Recorder.
- A DVD-RW disc that has been recorded by DAO(Disc At Once) on
a PC cannot be unfinalised.
- A DVD-RW disc that has been recorded in Video Mode of a
different maker’s recorder cannot be unfinalised.
- A DVD±R disc cannot be unfinalised.
Recording Formats
Since available functions differ depending on the disc type, select a disc
that best fits your preferences.
When you insert an unused disc, the following message appears.
• DVD-RAM/±RW/+R : Format will be started automatically.
• DVD-R : Initialising the disc is unnecessary.
Unformatted Disc.
Formatting. Please wait.
DVD-RAM/-RW(VR mode)/-R(VR mode)
• This mode allows multiple editing functions (such as deletion of the
whole title, partial deletion of a title, etc.).
• Various editing options using a created Playlist.
DVD-RW(V mode)/-R(V mode)
• Chapters will be created automatically when you finalise recording on
• Simple editing (erasing titles/changing title name).
M  You can initialise discs automatically using EZ REC MODE.
(see page 29).
English - 53
Recording
DVD-RW/-R discs in Video mode.
The chapter’s length (interval between chapters) varies according to the
recording mode.
Recording Mode
Select one of eight recording modes by pressing the REC MODE button
repeatedly while the unit is in Stop mode for the desired recording time
and picture quality. In general, picture quality improves as the
recording time decreases. In AUTO mode, the most suitable record mode
is adjusted automatically, according to remaining time on the disc and
length of the timer recording. This function is selected only one mode in
HQ, HSP, SP, LSP, ESP, LP, EP and SLP modes and you can use this mode
for timer recording.
Recording Mode
Recording Times
DVD-RW/-R
HQ (high quality mode)
Approx. 1 hour
HSP
Approx. 1 hour 30 minutes
SP (standard quality mode)
Approx. 2 hours
LSP
Approx. 2 hours 30 minutes
ESP
Approx. 3 hours
LP (long recording mode)
Approx. 4 hours
EP
Approx. 6 hours
SLP (long duration mode)
Approx. 8 hours
Recording
The dual layer DVD±Rs have approximately double the capacity of single layer
DVD±Rs.
M  Recording time may vary according to specific conditions.
 1GB = 1,000,000,000 bytes; actual formatted capacity may be less
as the internal firmware uses a portion of the memory.
 DVB-T recording is possible only on AUTO mode.
 On DVB-T recording, recording mode will be automatically
determined depending on the quality of the video (or audio).
English - 54
Unrecordable pictures
You cannot record copy protected movie.
Pictures with copy protection cannot be recorded on this DVD Recorder.
When the DVD Recorder receives a copy- guard signal while recording,
recording stops and the following message appears on the screen.
Concerning Copy Control Signals
TV broadcasts that contain copy control signals may have one of the
following three signal types, Copy-Free, Copy-Once and Copy-Never. If you
want to record a copy-once type programme, use DVD-RW with CPRM in
VR Mode and DVD-RAM discs.
Signal type
Copy-Free
Copy-Once
Copy-Never
DVD-RAM(Ver.2.0)
O
O*
–
DVD+RW
O
–
–
DVD+R
O
–
–
DVD-RW(Ver.1.1)
O
–
–
DVD-RW(Ver.1.1)
with CPRM
VR mode
V mode
O
O
O*
–
–
DVD-R
O
Media
–
Once “Copy Once” has been recorded, recording cannot be done anymore.
* Compatible with CPRM
◆ Content Protection for Recordable Media (CPRM)
English - 55
Recording
CPRM is a mechanism that ties a recording to the media on which it is
recorded. It is supported by some DVD Recorders, but not by many DVD
players. Each blank recordable DVD has a unique 64-bit media ID etched
in the BCA. When protected content is recorded onto the disc, it can be
encrypted with a 56-bit C2 (Cryptomeria) cipher derived from the media
ID.
During playback, the ID is read from the BCA and used to generate a key
to decrypt the contents of the disc. If the contents of the disc are copied
to other media, the ID will be absent or wrong and the data will not be
decryptable.
Disc contents cannot be copied to other media.
Recording immediately
DVD
-RW
VR
SP
XCVKL
AV 1
DVD-SR275M only
Before you start
1. Make sure antenna cable is connected.
2. Press the OPEN/CLOSE button and place a recordable disc on the disc
tray.
3. Check the remaining time on the disc.
DVD-RAM/DVD±RW/+R discs should be formatted or initialised in
advance before beginning recording. Most new discs are sold
unformatted. Make sure to format your unformatted discs before
recording.
4. Press the OPEN/CLOSE button to close the disc tray.
Wait until LOAD disappears from the front panel display.
Recording the current programme you are watching
1. Press the PROG ( / ) buttons or number buttons to select the
station you want to record.
2. Press the REC MODE button repeatedly, to select the recording Mode
(quality).
➞ HQ ➞ HSP ➞ SP ➞ LSP ➞ ESP ➞ LP ➞ EP ➞ SLP
3. Press the REC button.
Recording
Recording from external equipment you are watching
1. Power on your DVD Recorder and switch to AV mode by pressing the
INPUT SEL. button on the remote control. The front panel display
changes in the following sequence.
➞ PR ➞ AV1 ➞ AV2 ➞ AV3 ➞ DV
2. Press the REC MODE button repeatedly to select the recording Mode
(quality).
➞ HQ ➞ HSP ➞ SP ➞ LSP ➞ ESP ➞ LP ➞ EP ➞ SLP
3. When your DVD Recorder is in the Stop mode, set the operation mode
of your external devices to play mode.
4. Press the REC button on your DVD Recorder when the image from
which you want to start recording is displayed.
To pause recording
Press the PAUSE(
) button to pause a recording in progress.
• Press the PAUSE( ) button again to resume recording.
English - 56
To stop recording
Press the STOP button to stop a recording in progress.
• When using DVD-RAM/DVD±RW/±R discs, the message “Updating
the information of disc. Please wait for a moment.” is displayed.
M  You can not change the recording mode and the programme while
recording.
 Recording will stop automatically if there is no free space left for
recording.
 Up to 99 titles can be recorded onto a DVD-RAM/-RW/-R disc, up to
49 titles onto a DVD+RW/+R disc.
 If the power interrupted due to power failure or other reasons, the
title being recorded will not be saved onto the disc.
 Recording will stop automatically if a copy protected image is
selected.
 Do not use DVD-R authoring discs with this unit.
 Also refer to the user manual for your External Devices when
recording from external equipment using the Audio/Video cable or
scart cable.
Recording through the DV Input jack (DVD-SR275M only)
    ►  
DV
You may control the Camcorder using the IEEE1394 (DV) interface.
Follow these directions to record onto a disc from a
camcorder that has a DV output jack.
1. Connect the DV output jack of your camcorder to the DV input jack on
the front of your DVD Recorder using a DV cable.
<Move
sOk
Exit
2. Power on your DVD Recorder and switch to DV mode by pressing the
INPUT SEL. button on the remote control.
3. Press the REC MODE button repeatedly to select the recording Mode
(quality).
4. If the input is set to DV, a playback/record menu that enables
camcorder control appears on the top of the screen.
5. Select the Playback related icons on the upper part of the screen to
playback the camcorder and find the starting position for dubbing.
6. To start recording, Press the ◄► buttons to select REC (●) icon in the
top side of the screen, then press the OK button.
You can press the REC button on the remote control to start recording
7. Press the STOP button on your DVD Recorder when the recording is
finished.
M  Some camcorders may not work with your DVD Recorder even if
they have a DV output jack.
 Also refer to the user manual for your camcorder when recording
through a DV jack.
 To display playback related icons on the screen, press any direction
button on the remote control.
English - 57
Recording
➞ HQ ➞ HSP ➞ SP ➞ LSP ➞ ESP ➞ LP ➞ EP ➞ SLP
Making a One Touch Recording (OTR)
XCVKL
DVD-SR275M only
One-Touch Recording (OTR) allows you to add recording time in preset
minute increments up to 8 hours by pressing the REC button repeatedly.
1. Press the PROG ( / ) buttons or number buttons to select the station
to record. If you want to record through a connected external
component, press the INPUT SEL. button to select an appropriate
external input [ PR, AV1, AV2, AV3 or DV input(DVD-SR275M only) ].
2. Press the REC button.
3. While in Record mode, press the REC button again to activate
One-Touch Recording (OTR).
• Record length 0:30 appears on the On-Screen Display and the DVD
Recorder will record for exactly 30 minutes.
4. Continue press the REC to add recording time in preset minute
increments up to 8 hours.
• The DVD Recorder stops recording automatically when the time has
elapsed.
To stop recording
Recording
Press the STOP ( ) button.
The message “Press STOP button once more to cancel Timer Record” is
displayed.
Press the STOP ( ) button again.
The message “Updating the information of disc. Please wait for a moment”
is displayed.
M  The timer counter decreases by the minute from the recording time
set to 0:00, then the DVD Recorder stops recording.
Making a Timer Recording
XCVKL
DVD-SR275M only
1. Check the antenna cable is connected.
2. Check the remaining time of the disc.
3. Check the date and time are correct.
Make sure the Clock (Setup-Present Time) must be set before you
proceed with a timer recording. (See pages 24~25)
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Timer, then press the OK button.
3. Press the ▲▼ buttons to select Timer-Standard, then press the OK
button.
English - 58
4. Set timer recording option.
• Fill the input items using the ▲▼◄► buttons and number buttons.
◄► : Moves to the previous/next item.
▲▼, 0~9 : Sets a value.
Timer
• Date : Timer Recording allows setting the recording time within one
12:00
Timer
Title List
Timer - Standard
Timer - VIDEO Plus+
Timer List
month period. Set the recording day. (month/day)
Edit
Disc
Setting
31/01
Setup
>Move
sOk
rReturn
eExit
Sun
30/01
29/01
Mon-Fri
Mon-Sat
02/01
Sun-Sat
01/01
Today
• Start/End Time : Start and end time of the timer recording.
• Prog. : The video input source (AV1, AV2 or AV3), or the broadcasting
12:00
Timer - Standard
No.
Date
01 No.01--/-02
03
04
05
Start
End
Prog. Mode
PDC
--:--
--:--
----
---
►
--/---Date --:-Start --:-End ---Prog. --Mode PDC
--/---:-- --:-- ---- ----Today --:-12 : 00 --:-12 : 11 ---Prog. --1 SP Off
--/----
►
--/---:-06 ◄ VIDEO
--/-- Plus+
--:--
>Adjust
channel you want to make a timer recording from.
To convert DTV/Analogue, press DTV/ANALOG button of the
remote control.
On the DTV mode, you can change TV or RADIO by pressing the
TV/RADIO button on the remote control.
---
Edit
►
►
--:--
----
---
---
►
--:--
----
---
---
►
<Move
rReturn
eExit
‹ Recording Mode (DVD)
M  When you are recording at EP mode on a DVD-RW(V mode)/-R disc,
it may not record the full 6 hours because the unit uses the
VBR(Variable Bit Rate) ENCODING system. For example, if you
record a programme with a lot of action,
it uses a higher bit rate which in turn consumes more disc memory.
 DVB-T Timer recording is possible only on AUTO mode.
 On DVB-T recording, recording mode will be automatically
determined depending on the quality of the video (or audio).
English - 59
Recording
AUTO : Select when you want to set video quality automatically.
In AUTO mode, the most suitable record mode is adjusted automatically,
according to remaining time on the disc and length of the timer recording.
This function is selected only one mode in HQ, HSP, SP, LSP, ESP, LP, EP and SLP
modes and you can use this mode for timer recording.
HQ : Approx. 1 hour
HSP : Approx. 1 hour 30 minutes
SP (standard quality) : Approx. 2 hours
LSP : Approx. 2 hours 30 minutes
ESP : Approx. 3 hour
LP (low quality) : Approx. 4 hour
EP (extended mode) : Approx. 6 hour
SLP (long duration mode) : Approx. 8 hours
The dual layer DVD±Rs have approximately double the capacity of single
layer DVD±Rs.
• PDC : PDC (Programme Delivery Control) function.
- If you set this function on, you can control the starting and
ending time of recording by special signal included in the
broadcasting signal. If a TV programme is shortened or starts
earlier or later than scheduled, this function synchronizes the
starting and ending time of recording with the actual
broadcasting time automatically.
- Set up the start-time exactly according to the published TV
schedule. Otherwise the timer recording will not operate.
- Do not select PDC unless you are sure the programme you wish
to record is broadcast with PDC.
5. After selecting the set up value for each mode, press the OK button to
save the timer record.
If the timer settings overlap;
The first programme has priority.
After recording of the first programme is complete, the second
programme starts being recorded.
To exit without saving the current setting
Press the EXIT ( ) button.
To return to the previous menu
Press the RETURN button if you don’t want to set a timer recording.
6. Turn the power off to finish the Timer Recording setting.
•
will appear on the front panel. It means that a timer recording is
registered.
Timer Recording will not work when the power is on.
M  The timer recording time may differ from the set time depending
Recording
on disc status and overall timer recording status (for example,
recording times overlapping, or when the previous recording ends
within 2 minutes before the start time of the next recording.)
English - 60
Editing the Timer List
Timer
XCVKL
12:00
Timer
Title List
Timer - Standard
Timer - VIDEO Plus+
Timer List
DVD-SR275M only
Edit
Disc
Setting
Follow these directions to edit the timer record list.
Setup
1. With the unit in Stop mode, press the MENU button.
>Move
sOk
rReturn
eExit
12:00
Timer List
No.
Date
Start
End
Prog.
Mode
PDC
Edit
01
01/01
12:00
12:00
Prog. 1 SP
--/--
--:--
--:--
----
03
--/--
--:--
--:--
----
-Edit
--- Delete
-----
►
02
04
--/--
--:--
--:--
----
---
--
►
05
--/--
--:--
--:--
----
---
--
►
06
--/--
--:--
--:--
----
---
--
►
mMove
sOk
rReturn
►
►
eExit
2. Press the ▲▼ buttons to select Timer, then press the OK button.
3. Press the ▲▼ buttons to select the Timer List, then press the OK
button.
4. Press the ▲▼ buttons to select the number of the Timer List you want
to edit, then press the OK button.
• The Edit and Delete items are displayed.
5. Press the ▲▼ buttons to select Edit, then press the OK button.
• The Timer List screen is displayed. Edit the items you want to modify. See
the Timer List section for more information on Timer List Input items.
(See pages 58~59)
6. Press the OK button to confirm the edited setting.
7. Press the EXIT button after finishing the operation.
The menu screen will disappear.
12:00
Timer List
No.
Date
Start
End
Prog.
PDC
Edit
01
01/01
12:00
12:00
Prog. 1 SP
--
►
02
--/--
--
►
--/--
--:---:-- -----Do you want
to erase
--:---:-----"No. 01"?
---
--
►
04
--/--
--:--
---
--
►
--/--
--:---:-- OK--:--
----
05
Cancel ------
--
►
06
--/--
--:--
----
--
►
03
mMove
sOk
--:--
Mode
---
rReturn
eExit
Deleting the Timer List
XCVKL
DVD-SR275M only
Follow these directions to delete a title from the timer record list.
2. Press the ▲▼ buttons to select Timer, then press the OK button.
3. Press the ▲▼ buttons to select the Timer List, then press the OK
button.
4. Press the ▲▼ buttons to select the number of the Timer List you want
to delete, and then press the OK button.
• The Edit and Delete items are displayed.
5. Press the ▲▼ buttons to select Delete, then press the OK button.
• You will be prompted with the delete confirm message such as (“Do you
want to erase No.01?”).
6. Press the ◄ ► buttons to select OK, then press the OK button.
• The selected title will be deleted from the list.
7. Press the EXIT button after finishing the operation.
The menu screen will disappear.
M  You can not delete programmes that are currently being recorded.
English - 61
Recording
1. With the unit in Stop mode, press the MENU button.
Using the VIDEO Plus+ Feature
Timer
XCVKL
12:00
Timer
Title List
Timer - Standard
Timer - VIDEO Plus+
Timer List
DVD-SR275M only
Edit
Disc
Setting
Setup
>Move
sOk
rReturn
eExit
12:00
Timer - VIDEO Plus+
Title List
Edit
3. Press the ▲▼ buttons to select Timer-VIDEO Plus+, then press the OK
button.
• A message is displayed to allow you to enter the VIDEO Plus+ code.
Disc
Setting
Setup
<Move
◄ Standard
sOk
rReturn
eExit
12:00
Timer - Standard
No.
Date
01 No.01--/-02
03
04
05
Start
End
Prog. Mode
PDC
--:--
--:--
----
---
►
--/---Date --:-Start --:-End ---Prog. --Mode PDC
--/---:-- --:-- ---- ----Today --:-12 : 00 --:-12 : 11 ---Prog. 1---SP Off
--/----
►
--/---:-06 ◄ VIDEO
--/-- Plus+
--:--
>Adjust
---
Edit
►
►
--:--
----
---
---
►
--:--
----
---
---
►
<Move
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Timer, then press the OK button.
Set VIDEO Plus+ code number. [0~9]
Timer
Before presetting your DVD Recorder.
• Switch on both the television and your DVD Recorder.
• Check that the date and time are correct.
Up to twelve programmes can be preset
rReturn
eExit
4. Press the number buttons to enter the code of the programme that
you want to record in your television magazine.
• If you want to correct the VIDEO Plus+ code that you are entering:
- Press the ◄ button until the digit to be corrected is cleared.
- Enter the correct digit.
5. Press the OK button.
• The information concerning the programme is displayed.
• When using the VIDEO Plus+ function for the first time with stored
stations, the programme number flashes. This one time, you must
enter the PR number manually by pressing the ▲▼ buttons.
6. If the programme and times are correct, press the OK button.
7. Turn the power off by pressing the STANDBY/ON button to activate
the timer list setting.
• Refer to pages 58~59 if you wan t to
Recording
- Check whether the timer Recording has set correctly or not.
- Cancel a preset recording.
M  The numbers next to each TV programme listing in the magazines
or newspapers are VIDEO Plus+ code numbers, which allow you to
programme your DVD Recorder. instantly with the remote control.
Enter the VIDEO Plus+ code for the programme you wish to record.
 VIDEO Plus+ is a trademark of Gemstar Development Corporation.
VIDEO Plus+ system is manufactured under licence from Gemstar
Development Corporation.
English - 62
Check Remaining Time
Press INFO button on the remote control.
The following information will be displayed.
(Current deck status, recording Mode, remaining time, input channel,
current time.)
When you watch or record DVB-T broadcast, this function is not available.
DVD-RW
Stop
0:00:00
SP
Rem 02:00
Prog. 1
Mon 01 Jan. 2007
12:00
DV Dubbing (DVD-SR275M only)
12:00
DV Dubbing
Title List
Timer
DV Simple Dubbing
DV One Touch Dubbing
Before DV Dubbing, connect the DV output jack of camcorder to the DV
input jack of DVD Recorder using a DV cable.
1. With the unit in Stop mode, press the MENU button in stop mode.
Edit
2. Press the ▲▼ buttons to select Dubbing, then press the OK button.
DV Dubbing
Disc
Setting
Setup
>Move
sOk
DV Tape Mode
rReturn
eExit
3. Press the ▲▼ buttons to select DV Dubbing, then press the OK
button.
    ►  
DV Simple Dubbing
You can find the dubbing start point to record on a disc easily by using the
DV Simple Dubbing function.
<Move
sOk
Exit
To setup, follow steps 1~3 on page 62
4. Press the ▲▼ buttons to select DV Simple Dubbing, then the OK
button.
The DV Tape Mode screen will be displayed.
6. If you find start point, press the ◄► button to select REC (●), then
press the OK button.
Dubbing starts.
English - 63
Recording
5. Select the playback related buttons using the ◄► button to find the
dubbing start point.
DV One Touch Dubbing
12:00
DV Dubbing
Title List
Timer
DV Simple Dubbing
DV One Touch Dubbing
To setup, follow steps 1~3 on page 62
Edit
DV Dubbing
Disc
Setting
Setup
s
Ok
s
Ok
r
Return
r
Return
e
Exit
e
Exit
4. Press the ▲▼ buttons to select DV One Touch Dubbing, then press
the OK button.
DVD Recorder rewinds the tape in the digital video camera and then
starts recording the tape contents from the beginning.
When playback of the tape stops, One Touch Dubbing ends
automatically.
Recording
>>
Move
Move
You can record the entire contents of a DV format tape onto a disc easily
by using the DV One Touch Dubbing function.
English - 64
Editing
This section introduces basic functions of DVD editing and explains both edit functions for the recording on a disc and
edit functions for the entire disc.
Playing the Title List
XCVKL
DVD-SR275M only
Follow these instructions to play back a title from the Title List.
1. Press the TITLE LIST button.
The Title List screen is displayed.
2. Press the ▲▼ buttons to select a title you want to play from Title List,
and then press the PLAY button.
3. Press the STOP button to stop playing.
To return to the title list screen, press the TITLE LIST button.
d e
c
DVD
-RW
Title List (Original)
No.
1/4
T
f
JAN/01/2008 01:00 AV1
01
02
03
04
Title
JAN/01/2008
JAN/01/2008
JAN/01/2008
JAN/01/2008
g
Title List Screen Elements
12:00
Length Edit
00:00:11
00:00:09
00:01:36
00:00:11
c Playback screen for recorded titles
d Information window for the selected title: Title name, recording date, lock
►
►
►
►
status, recording mode
01.Jan.2007
12:06
LSP
>Move
DVD
-RW
sOk
Title List (Original)
No.
1/4
T
rReturn
JAN/01/2008 01:00 AV1
01
02
03
04
Title
JAN/01/2008
JAN/01/2008
JAN/01/2008
JAN/01/2008
A-B Erase
LSP
sOk
rReturn
eExit
h
e Recorded title No.
f Recorded title name
g Recording Length (i.e., the playing time)
h Edit menu
Play : Plays the selected title.
Title Erase : Erase the selected title from the list.
Chapter Erase : Erase the selected chapter from the title.
Protect : Locks or unlocks the selected title.
Title Name : Changes the name of a selected title.
A-B Erase : Erase the selected section (scene) from the title.
Divide Title : Divide a title into two.
i Button display
M  During the playback, press the ANYKEY button. you can play
desired title. (see page 47)
 This may depend on the type of disc.
 DVD-RW(V)/+RW/-R(V)/+R discs have limited editing functions.
English - 65
Editing
Divide Title
>Move
i
12:00
Length Edit
00:00:11 ►
Play
00:00:09
Title
Erase ►
00:01:36
►
Chapter
Erase
00:00:11 ►
Protect
Title Name
01.Jan.2008
12:06
eExit
Basic Editing (Title List)
Changing the Name of a Title (Title Name)
Follow these instructions to rename a title list, i.e., to edit the title of a
recorded programme.
XCVKL
12:00
Title Name
Sports(A1)
A
F
K
P
U
Z
B C
G H
L M
Q R
V W
D
I
N
S
X
E
J
O
T
Y
a
f
k
p
u
z
Backspace
mMove
DVD
-RW
h
m
r
w
l
q
v
Space
sOk
d
i
n
s
x
e
j
o
1
6
-
2
7
_
t
y
~
%
!
^
Delete
No.
01
02
03
04
Sports(A1)
3
8
+
@
&
Clear
rReturn
Title List (Original)
3/4
T
c
b
g
Title
JAN/01/2008
JAN/01/2008
Sports(A1)
JAN/01/2008
4
9
=
#
(
5
0
.
$
)
Finish
eExit
12:00
Length Edit
00:00:11
00:00:09
00:01:36
00:00:11
►
►
►
►
01.Jan.2008
12:06
>Move
LSP
sOk
rReturn
eExit
DVD-SR275M only
1. Press the TITLE LIST button.
The Title List screen is displayed.
2. Press the ▲▼ buttons to select a title you want to rename from the
Title List, then press the OK button.
3. Press the ▲▼ buttons to select Title Name, then press the OK button.
The Title Name screen is displayed.
4. Select the desired characters using the ▲▼◄ ► buttons, press the OK
button.
• Backspace : Deletes the character before the cursor.
• Space : Enters a blank and moves the cursor one forward (to the
right).
• Delete : Deletes the character at the cursor position.
• Clear : Deletes all the character inputs.
• Finish : Registers the character inputs.
Editing
5. Press the ▲▼◄ ► buttons to select Finish, and then press the OK
button.
The changed title name is displayed in the title field of the selected
title.
English - 66
Locking (Protecting) a Title
Follow these instructions to lock a title to protect it from accidental
deletion.
DVD
-RW
Title List (Original)
XCVKL
12:00
1/1
(VR mode)DVD-SR275M only
Select the protection
status for this title.
T
JAN/01/2008 01:00 AV1
On
01.Jan.2008
12:06
LSP
>Move
DVD
-RW
sOk
rReturn
Title List (Original)
No.
3/4
T
1. Press the TITLE LIST button.
The Title List screen is displayed.
Off
JAN/01/2008 01:00 AV1
01
02
03
04
eExit
12:00
Title
JAN/01/2008
JAN/01/2008
JAN/01/2008
JAN/01/2008
Length Edit
00:00:11
00:00:09
00:01:36
00:00:11
►
►
►
►
01.Jan.2008
12:06
LSP
>Move
sOk
rReturn
2. Press the ▲▼ buttons to select a title you want to protect from the
Title List, then press the OK button.
3. Press the ▲▼ buttons to select Protect, then press the OK button.
You will be prompted with a confirmation message.
The Message “Select the protection status for this title.” is displayed.
4. Press the ◄ ► buttons to select On, then press the OK button.
The key icon on the information window for the selected title changes
to the locked status. ( → )
eExit
Erasing a Title (Title Erase)
Follow these instructions to erase a title from the Title List.
DVD
-RW
Title List (Original)
1/1
T
JAN/01/2008 01:00 AV1
01.Jan.2008
12:06
>Move
XCVKL
12:00
Do you want to erase
"No.01"?
(If you have created a Playlist
or Dubbing list with this title.
part of that playlist or Dubbing
list will also be erased.)
LSP
OK
sOk
rReturn
Cancel
eExit
DVD-SR275M only
1. Press the TITLE LIST button.
The Title List screen is displayed.
2. Press the ▲▼ buttons to select a title you want to erase from the Title
List, then press the OK button.
• The message depends on the type of disc.
4. Press the ◄ ► buttons to select OK, then press the OK button.
M  You cannot erase a protected title.
If you want to erase a protected title, select “Off ” in the Title
Protection menu.
 Once a title is erased from the Title List, it cannot be recovered.
 Once DVD-RW/DVD±R is finalised, it cannot be erased.
English - 67
Editing
3. Press the ▲▼ buttons to select Title Erase, then press the OK button.
You will be prompted with a confirmation message.
DVD-RAM(VR mode), DVD-RW(VR mode) : Since Playlist is present, the
message ‘Do you want to erase "No. 01"? (If you have created a Playlist
or Dubbing list with this title, part of that Playlist or Dubbing list will
also be erased.)’ is displayed.
DVD-RW(Video mode), DVD+RW,DVD+R,DVD-R(Video mode): Since
Playlist is not present, the message ‘Do you want to erase "No. 01"?’ is
displayed.
 With DVD±R, titles are only erased from the menu, however, the
Title remains physically on the disc.
Erasing a chapter (Chapter Erase)
Follow these instructions to erase a chapter from the Title List.
DVD
Chapter Erase (Original)
-RW
Chapter No. 1 / 7
XCV
12:00
Title No.02
Check
Erase
01 00:00:03
02 00:00:42
03 00:00:04
04 00:00:03
05 00:00:11
06 00:00:04
mMove
sOk
rReturn
DVD
Chapter Erase (Original)
-RW
Chapter No. 1 / 1
eExit
12:00
Title No.02
Check
Erase
Do you want to erase "No.01"?
01 00:00:03 02 00:00:42 03 00:00:04
OK
Cancel
Modify
Move
Add
04 00:00:03
mMove
05 00:00:11
sOk
06 00:00:04
rReturn
Copy
eExit
1. Press the TITLE LIST button.
The Title List screen is displayed.
(VR mode)
2. Press the ▲▼ buttons to select a title you want to erase from the Title
List, then press the OK button.
3. Press the ▲▼ buttons to select Chapter Erase, then press the OK
button.
The Chapter Erase screen is displayed.
4. Press the ▲▼◄► buttons to select a chapter you want to erase from
the Title List, then press the OK button. Check is selected.
To preview the chapter, then press the OK button.
When you press the RETURN button, the display returns to Chapter
Erase (Original).
5. Press the ▲▼ buttons to select Erase, then press the OK button.
You will be prompted with a confirmation message.
The Message "Do you want to erase "No. 01"?" is displayed.
6. Press the ◄► buttons to select OK, then press the OK button.
The selected chapter is erased from the title.
To erase other chapters, repeat from step 4.
M  You can also erase chapters from a Playlist title.
 If you erase an original title used in a Playlist, that Playlist is also
Editing
erased.
English - 68
Erasing a section of a Title (A-B Erase)
Follow these instructions to erase a section of a Title List entry.
DVD
-RW
A-B Erase
XCVK
12:00
Title No. 03
(VR mode)
Start
1. Press the TITLE LIST button.
The Title List screen is displayed.
End
Start 00:00:02
Erase
►
T
00:00:02
Title No. 2
01.Jan.2008 14:15
>Move
DVD
-RW
Finish
2. Press the ▲▼ buttons to select a title you want to edit from the Title
List, then press the OK button.
End 00:00:00
sOk
rReturn
A-B Erase
eExit
3. Press the ▲▼ buttons to select A-B Erase, then press the OK button.
The A-B Erase screen is displayed.
12:00
Title List No. 03
Start
4. Press the OK button at the starting point.
The image and starting point time are displayed in the section deletion
starting point window.
End
Start 00:00:02
T
Erase
■
Title No. 2
01.Jan.2008 14:15
>Move
DVD
-RW
00:00:15
Finish
End 00:00:15
sOk
rReturn
A-B Erase
5. Press the OK button at the end point.
The image and end point time is displayed in the Section deletion
ending point window.
eExit
12:00
6. Press the ▲▼ buttons to select Erase, then press the OK button.
Title List No. 03
Do you want to erase?
Erased part will not be restored.
Start
7. Press the ◄ ► buttons to select OK, then press the OK button.
The selected section has been deleted.
To return to the Title List, press the ▲▼ buttons to select Finish.
End
Start 00:00:00
OK
►
T
00:00:02
Title No. 2
01.Jan.2008 14:15
>Move
Cancel
Erase
Finish
End 00:00:15
sOk
rReturn
eExit
c
DVD
-RW
A-B Erase
A-B Erase Screen Elements
12:00
➀ Playback bar
Title List No. 02
Start
End
Start 00:00:02
Erase
►
T
00:00:02
Title No. 2
01.Jan.2008 14:15
>Move
Finish
End 00:00:00
sOk
rReturn
eExit
e
d
f
➁ Playtime
➂ Section deletion starting point window and time
➃ Section deletion end point window and time
• Select the start and end points of the section you want to delete
using the playback related buttons.
• Playback related buttons : (
,
,
,
,
,
)
long.
 End point cannot be marked earlier than start point.
 The section cannot be deleted when it includes a still picture.
English - 69
Editing
M  The length of the section to be deleted must be at least 5 seconds
Dividing a title into two (Divide Title)
Follow these instructions to divide a title into two.
XCVK
(VR mode)
1. Press the TITLE LIST button.
The Title List screen is displayed.
2. Press the ▲▼ buttons to select a title you want to devide from the Title
List, then press the OK button.
DVD
-RW
Divide Title (Original)
12:00
Title No. 01
Point
Divide
Start 00:00:02
►
T
00:00:02
Title No. 1
01.Jan.2008 14:15
>Move
DVD
-RW
End 00:00:00
sOk
rReturn
Divide Title (Original)
eExit
12:00
Title No. 01
Point
Divide
Start 00:00:02
00:00:10
II
T
Title No. 1
01.Jan.2008 14:15
>Move
DVD
-RW
End 00:00:10
sOk
rReturn
Divide Title (Original)
eExit
12:00
Title No. 01
Point
Do you want to divide title "No. 01"?
Divide
3. Press the ▲▼ buttons to select Divide Title, then press the OK button.
The setting the dividing point screen is displayed.
The Point is selected.
4. Press the OK button at the point where you want to divide the title.
The Divide is selected.
5. Press the OK button.
You will be prompted with a confirmation message.
The Message “Do you want to divide title “No.01”?” is displayed.
To reset the dividing point, select No and press the OK button, then
repeat from step 4.
The display asks whether you want to rename the title.
To use the same name as before, select No and press the OK button to
finish.
6. Press the ◄► buttons to select Yes, then press the OK button.
The Title Name screen is displayed.
7. Follow steps 3 to 5 of Changing the Name of a Title (page 66) to
complete renaming.
The devided title appears in the Title List with the new name.
Start 00:00:00
II
T
Yes
00:00:02
Title No. 1
01.Jan.2008 14:15
End 00:00:10
sOk
rReturn
eExit
Editing
>Move
No
English - 70
Advanced Editing (Playlist)
Creating a Playlist
Follow these instructions to create a new playlist title from a recorded
title.
DVD
-RW
Create Playlist
XCV
12:00
(VR mode)
Scene No. 01
Start
End
Start 00:00:01
Make
Title No. 01
►
00:00:01
Playlist No. 01
01.Jan.2008 14:15
T
>Move
DVD
-RW
Finish
End 00:00:00
sOk
rReturn
Create Playlist
eExit
12:00
Scene No. 01
Start
End
Start 00:00:01
Make
Title No. 02
■
Playlist No. 01
01.Jan.2008 14:15
T
>Move
00:00:30
Finish
End 00:00:30
sOk
rReturn
eExit
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Edit, then press the OK button.
3. Press the ▲▼ buttons to select Create Playlist, then press the OK
button.
The Create Playlist screen is displayed.
4. Press the OK button at the start point.
• The image and time at the start point are displayed on the Start
window.
• Select the starting point of the section from which you want to
create a new scene using the playback related buttons.
• Playback related buttons : (
DVD
-RW
Playlist
No.
1/3
01
02
03
T
Title
JAN/01/2008
JAN/01/2008
JAN/01/2008
12:00
Length Edit
00:00:11 ►
00:00:25 ►
00:00:05 ►
01.Jan.2008
>Move
LSP
sOk
,
,
,
,
)
5. Press the OK button at the end point.
• The image and end point time are displayed in the End window.
- To make a new playlist -
JAN/01/2008 01:00 AV1
12:06
,
rReturn
eExit
6. Press the ▲▼ buttons to select Make, then press the OK button.
A new Make Scene screen is displayed.
A new Scene will be added to the current Playlist.
M  You can check and see all the scenes on the Edit Playlist screen.
(See page 71)
 Repeat steps 1~5 if you want to make a new playlist.
 Repeat steps 4~5 if you want to make scenes of the playlist.
- To return to Edit Playlist menu -
M  You can create up to 99 playlist titles.
 Depending on the kind of disc, the displayed screen may be slightly
different.
 A disc that is recorded on this unit cannot be displayed playlist
menu if EZ Record mode set to "On".
English - 71
Editing
7. Press the ▲▼ buttons to select Finish, then press the OK button.
The Edit Playlist screen is displayed.
Playing Titles in the Playlist
Follow these instructions to play the playlist titles.
DVD
-RW
Playlist
No.
1/3
01
02
03
T
12:00
Length Edit
Title
JAN/01/2008 Play00:00:11 ►
JAN/01/2008 Title00:00:09
Erase ►
JAN/01/2008 Title00:01:36
Name ►
JAN/01/2008 01:00 AV1
01.Jan.2008
12:06
LSP
>Move
sOk
rReturn
eExit
XCV
(VR mode)
1. Press the TITLE LIST button with the disc stopped, then press the
PLAYLIST button.
The Edit Playlist screen is displayed.
2. Press the ▲▼ buttons to select the title you want to play from the
Playlist, then press the OK button.
3. Press the ▲▼ buttons to select Play, then press the OK button.
The playlist titles will be played back.
4. Press the STOP button to stop playing.
The screen returns to the Edit Playlist screen.
M  When the Title list or Playlist screen is displayed, you can toggle the
Title list and Playlist by pressing the PLAY LIST button.
Editing a Playlist
Follow these instructions to edit the playlist titles or scenes within then,
without changing the actual recordings.
XCV
1. With the unit in Stop mode, press the MENU button.
(VR mode)
2. Press the ▲▼ buttons to select Edit, then press the OK button.
3. Press the ▲▼ buttons to select Edit Playlist, then press the OK button.
The playlist screen is displayed.
4. Press the ▲▼ buttons to select a Playlist title, then press the OK button.
5. Press the ▲▼ buttons to select a desired option, then press the OK button.
• Play : Allows you to play a playlist.
• Title Erase : Erase the title (See page 67).
• Title Name : Allows you to rename the title (See page 66).
Editing
Renaming a Playlist Title
Follow these instructions to rename a playlist title, i.e., to edit the title of
a playlist title.
XCV
12:00
Title Name
Butterfly_
A
F
K
P
U
Z
B C
G H
L M
Q R
V W
D
I
N
S
X
Backspace
mMove
E
J
O
T
Y
a
f
k
p
u
z
b
g
l
q
v
Space
sOk
c
h
m
r
w
d
i
n
s
x
e
j
o
1
6
-
2
7
_
t
y
~
%
!
^
Delete
Clear
rReturn
3
8
+
@
&
4
9
=
#
(
5
0
.
$
)
Finish
eExit
(VR mode)
1. Press the TITLE LIST button with the disc stopped, than press the
PLAYLIST button.
The Edit Playlist screen is displayed.
2. Press the ▲▼ buttons to select the title you want to play from the
Playlist, then press the OK button.
3. Press the ▲▼ buttons to select Title Name, then press the OK button.
The Title Name screen is displayed.
4. Enter the desired characters using the ▲▼◄ ► buttons, press the OK
button.
English - 72
• Backspace : Deletes the character before the cursor.
• Space : Enters a blank and moves the cursor one forward (to the
DVD
-RW
Playlist
No.
3/4
T
01
02
03
04
Butterfly
Title
JAN/01/2008
JAN/01/2008
Butterfly
JAN/01/2008
12:00
Length Edit
00:00:11
00:00:09
00:01:36
00:00:11
►
►
►
►
01.Jan.2008
12:06
>Move
sOk
rReturn
eExit
right).
• Delete : Deletes the character at the cursor position.
• Clear : Deletes all the character inputs.
• Finish : Registers the character inputs.
5. Press the ▲▼◄ ► buttons to select Finish, and then press the OK
button.
The changed title is displayed in the title field of the selected title.
Deleting a Playlist Title from the Playlist
DVD
-RW
Playlist
No.
1/3
01
02
03
T
Title
12:00
Length Edit
XCV
JAN/01/2008 Play00:00:11 ►
JAN/01/2008 Title00:00:09
Erase ►
JAN/01/2008 Title00:01:36
Name ►
(VR mode)
JAN/01/2008 01:00 AV1
01.Jan.2008
12:06
LSP
>Move
DVD
-RW
sOk
rReturn
eExit
Playlist
12:00
1/1
Do you want to erase
"No.01"?
T
Follow these instructions to rename a playlist title, i.e., to edit the title of
a playlist title.
JAN/01/2008 01:00 AV1
01.Jan.2008
OK
12:06
>Move
sOk
rReturn
Cancel
eExit
1. Press the TITLE LIST button with the disc stopped, than press the
PLAYLIST button.
The Edit Playlist screen is displayed.
2. Press the ▲▼ buttons to select the title you want to play from the
Playlist, then press the OK button.
3. Press the ▲▼ buttons to select Title Erase, then press the OK button.
The Title Name screen is displayed.
4. Press the ◄ ► buttons to select OK, then press the OK button.
After the delete operation is complete, it will automatically return to the
Edit Playlist screen.
Editing
English - 73
Disc Setting
Menu items may vary, depending on the existence of a recorded title.
Editing the Disc Name
12:00
Disc Name
Follow these instructions to give a name to a disc.
XCVKL
Disc_
A
F
K
P
U
Z
B C
G H
L M
Q R
V W
D
I
N
S
X
a
E
J
O
T
Y
f
k
p
u
z
Backspace
mMove
b
g
l
q
v
Space
sOk
c
h
m
r
w
d
i
n
s
x
e
j
o
1
6
-
2
7
_
t
y
~
%
!
^
Delete
Clear
rReturn
Timer
Edit
Disc
Setting
&
4
9
=
#
(
5
0
.
$
)
Finish
eExit
12:00
Disc Setting
Title List
3
8
+
@
Disc Name
: Disc
Disc Protect
: Not Protected
Disc Format
: VR Mode
Disc Finalise
: Unfinalised
Disc Information
Erase All Titles
sOk
rReturn
2. Press the ▲▼ buttons to select Disc Setting, then press the OK
button.
3. Press the ▲▼ buttons to select Disc Name, then press the OK button.
The Disc Name screen is displayed.
4. Enter the desired characters using the ▲▼◄ ► buttons.
Setup
>Move
1. With the unit in Stop mode, press the MENU button. DVD-SR275M only
eExit
•
•
•
•
•
Backspace : Deletes the character before the cursor.
Space : Enters a blank and moves the cursor one forward (to the right).
Delete : Deletes the character at the cursor position.
Clear : Deletes all the character inputs.
Finish : Registers the character inputs.
5. Press the ▲▼◄ ► buttons to select Finish, then press the OK button.
A disc name is given to the disc.
M  To edit the disc name, you need to clear disc protection in advance.
 Depending on the kind of disc, the displayed screen may be
different.
Disc Protection
Disc Setting
Title List
Timer
Edit
Disc
Setting
Disc Name
: Disc
Disc Protect
: Not Protected
Disc Format
: VR Mode
Disc Finalise
: Unfinalised
Disc Information
Erase All Titles
(VR mode) DVD-SR275M only
Editing
Setup
>Move
XCVK
12:00
sOk
rReturn
eExit
Disc Protect allows you to protect your discs from being formatted
or deleted due to unintended operations.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Setting, then press the OK
button.
3. Press the ▲▼ buttons to select Disc Protect, then press the OK
button.
4. Press the ▲▼ button to select Protected, then press the OK button.
English - 74
Formatting a Disc
Use these instructions to format a disc.
The Disc Protection should be cleared.
<DVD-RAM>
Timer
Edit
Disc
Setting
Disc Name
: Disc
Disc Protect
: Not Protected
Disc Format
: VR Mode
Disc Finalise
: Unfinalised
Select the recording format.
Disc Information
Erase All Titles
Setup
>Move
XCK
12:00
Disc Setting
Title List
VR Mode
sOk
DVD-SR275M only
1. With the unit in Stop mode, press the MENU button.
Video Mode
rReturn
eExit
2. Press the ▲▼ buttons to select Disc Setting, then press the OK
button.
3. Press the ▲▼ buttons to select Disc Format, then press the OK
button.
<DVD-RW>
DVD+RW
12:00
Disc Setting
Title List
Timer
Edit
Disc
Setting
Setup
>Move
Disc Name
: Disc
Disc Protect
: Not Protected
Disc Format
: VR Mode
Disc Finalise
: Unfinalised
Select the recording format.
Disc Information
Erase All Titles
VR Mode
sOk
will be erased (even protected titles). Do you want to format this
disc?’.
DVD-RAM/-RW
Video Mode
rReturn
• You will be prompted with the confirmation message ‘All of the data
• You will be prompted with the confirmation message ‘Select the
eExit
recording format.’ (When using a DVD-RAM disc, you can select VR
mode only)
You will be prompted with the confirmation message ‘All of the data
will be erased (even protected titles). Do you want to format this
disc?’.
• You will be prompted with the confirmation message ‘Do you want
to format disc?’.
4. Press the ◄► buttons to select OK, then press the OK button.
The disc is formatted.
M  You can change the disc mode only one time when the unused
DVD-R disc is inserted.
DISC
DVD-VR mode
DVD-V mode
DVD-RAM
DVD-RW
DVD-R
DVD-RW
DVD-R
English - 75
Editing
DVD-VR and DVD-V mode are defined according to their recording
format.
Finalising a Disc
After you record titles onto a DVD-RW/±R disc with your DVD Recorder,
it needs to be finalised before it can be played back on external devices.
Timer
Edit
Disc
Setting
Disc Name
: Disc
Disc Protect
: Not Protected
Disc Format
: VR Mode
Do
you
want to finalise
this disc?
Disc
Finalise
: Unfinalised
Disc Information
Erase All Titles
Finalise
Setup
>Move
CVL
12:00
Disc Setting
Title List
sOk
DVD-SR275M only
1. With the unit in Stop mode, press the MENU button.
Unfinalise
rReturn
eExit
2. Press the ▲▼ buttons to select Disc Setting, then press the OK
button.
3. Press the ▲▼ button to select Disc Finalise, then press the OK button.
You will be prompted with the message ‘Do you want to finalise this
disc?’
4. Press the ◄ ► buttons to select Finalise, then press the OK button.
You will be prompted again with the message “Disc will be finalised.
Do you want to continue?”
5. Press the ◄ ► buttons to select OK, then press the OK button.
The disc is finalised.
M  Once a disc is finalised, you cannot delete titles from the record list.
 Once a DVD±R/DVD-RW (video mode)disc is finalised, it is playable
in a standard DVD player.
 Depending on the disc type, the displayed screen may be different.
 Finalising time may be different depending on the amount of data
recorded on the disc.
 Data on the disc will be damaged if the recorder is powered off
during finalise process.
 You can finalise the disc automatically using EZ Record.
(see page 29).
Unfinalising a Disc (V/VR mode)
Editing
Timer
Edit
Disc
Setting
Setup
>Move
C
12:00
Disc Setting
Title List
Disc Name
: Disc
Disc Protect
: Not Protected
Disc Format
: VR Mode
Do you
want to unfinalise
disc?
Disc
Finalise
: Unfinalised
Disc Information
Erase All Titles
Finalise
sOk
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Setting, then press the OK
button.
Unfinalise
rReturn
eExit
3. Press the ▲▼ button to select Disc Finalise, then press the OK button.
You will be prompted with the message ‘Do you want to unfinalise
disc?’.
4. Press the ◄ ► buttons to select Unfinalise, then press the OK button.
You will be prompted again with the message “Disc will be unfinalised.
Do you want to continue?”
5. Press the ◄ ► buttons to select OK, then press the OK button.
The disc is unfinalised.
English - 76
M  A DVD-RW can be finalised or unfinalised in V mode.
Finalise
Unfinalise
Mark
DVD-Video(RW)
DVD-RW(V)
Operation
Same as DVD-Video
Additional recording,
protection and deletion
are possible.
 A DVD-RW can be finalised or unfinalised in VR mode.
Finalise
Unfinalise
Mark
DVD-RW(VR:F)
DVD-RW(VR mode)
Operation
Additional recording,
deletion, editing, and
protection are
impossible.
Additional recording,
deletion, editing, and
protection are possible.
Disc Information
XCVKL
DVD-SR275M only
12:00
Disc Information
Disc Name
Media
DVD-RW
Title No.
Protected
Date
Not Protected
1.01.2007 ~ --.--.----
Format
VR Mode
Original 1 / Playlist 0
HQ : 0H59M HSP : 1H29M SP : 2HOM
LSP : 2H29M ESP : 2H59M LP : 4H0M
EP : 6H1M SLP : 8HOM 4.6 / 4.7GB
Remainder
rReturn
eExit
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Setting, then press the OK
button.
3. Press the ▲▼ buttons to select Disc Information, then press the OK
button.
The Disc Information is displayed.
Erase All Titles
Disc Name
: Disc
Disc Protect
: Not Protected
Timer
Disc Format
: VR Mode
Edit DoDisc
Unfinalised
youFinalise
want to erase:all
the titles?
Disc
Information
Disc
Setting Erase All Titles
OK
Cancel
Setup
>Move
sOk
rReturn
DVD-SR275M only
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Disc Setting, then press the OK
button.
eExit
3. Press the ▲▼ buttons to select Erase All Titles, then press the OK
button.
• You will be prompted with the confirmation message ‘Do you want
to erase all the titles?’.
• When Protected Title exists : The Erase All Title List function will not
operate. If there is a title containing a still picture, however, that
function will not operate. If you want to delete a protected title,
disable Protect for it on the Lock item.
4. Press the ◄ ► buttons to select OK, then press the OK button.
All title lists are deleted.
English - 77
Editing
XCVL
12:00
Disc Setting
Title List
Reference
Troubleshooting (DVD)
If your product malfunctions, go through the check points below before contacting a Samsung authorized
service centre.
Problem
Explanation/Solution
• Check whether the power cord is securely plugged into the power outlet.
• Did you press the button of your DVD Recorder.
The input is displayed
for a while when the
power turns on.
The DVD Recorder requires some time to initialise after it is turned on.
Cannot record TV
programmes.
• Check whether the power cord is securely plugged into the power outlet.
• Did you set the DVD Recorder programme settings correctly?
• Check the free space on your disc.
• Check the antenna cable is connected.
Timer recording does
not work properly.
• Check the recording time, end time and current time settings again.
• Recording will be cancelled if the power is interrupted due to a power failure or other reason
during recording.
Cannot record.
• Check whether the disc is formatted. This product can record on formatted discs only.
• Check whether your disc has a sufficient free space.
I pressed the REC
button but there is no
response.
If a programme is copy protected, you cannot record it.
I forgot the password
for parental lock.
Press the PLAY/PAUSE ( ) buttons on the front panel of your DVD Recorder for 5 seconds, and
then press the STANDBY/ON button.
All settings including password will revert to factory settings.
Do not use it if not absolutely required.
(Note that this function is available only when there is no disc inserted.)
Cannot play the disc.
• Check whether the disc is inserted correctly with the label facing up.
• Check the regional code of your DVD disc.
• This DVD Recorder cannot playback some types of disc.
No sound.
• Are you watching a programme in slow or skip mode?
If you are playing a programme at a speed other than normal speed, sound is not output.
(But, you can hear sound during forward search (FF1) in DVD-VIDEO/DVD-RAM/±RW/±R))
• Check the connections and initial settings.
• Check whether the disc is damaged.
Clean up the disc, if necessary.
• Check whether the disc is inserted correctly with the label facing up.
Reference
No power.
English - 78
Troubleshooting (DVD)
Problem
Explanation/Solution
icon appears on
the screen.
You cannot use the operation or function due to one of the following reasons:
(1) Your DVD disc does not support the feature (for example, angles)
(2) You’ve requested a title, chapter, or scan time that is out of the correct range.
Play mode settings are
different from the
settings configured
with the Setting menu.
The disc does not support all the selected functions.
In this case, some settings you configure on the Setting menu may not work properly.
Cannot change the
aspect ratio.
Aspect ratio is fixed for DVD disc.
No audio output.
Check whether you selected correct digital output options in the Audio Output Options menu.
Did you move your DVD Recorder suddenly from a cold place to a warm place? In this case, do
No video or audio output.
not connect the plug to the power outlet and wait for two hours.
The disc tray is ejected after
Then insert the disc and try to play again. It will work properly when condensation has
2 to 5 seconds.
evaporated.
Angle operation does not
work during playback of Angle operation is available only when the disc contains images captured at different angles.
a DVD disc.
The disc revolves, but no
image or bad quality
images are output.
• Check whether there is damage or foreign materials on your disc.
• Some discs with bad manufacturing quality may not be played back.
• If the scene changes from dark to bright suddenly, the screen may jitter temporarily, but it is
not a defect.
Desired audio language Audio languages and subtitle languages are disc-specific.
Only the sound and subtitle languages contained on a DVD disc are available and displayed on
and subtitle language
are not played.
the disc menu.
• Check whether you selected correct Progressive options in the Video Options.
The remote control
doesn’t work.
• Point the remote control at the remote control sensor on your DVD Recorder. Operate within
distance. (15ft)
Remove obstacles between your DVD Recorder and remote control.
• Check whether the batteries are depleted.
Other problems
• Read the table of contents and then find and read the sections describing your problem, and
follow the directions given.
• Turn the unit off and on.
• If your problem still persists, contact your nearest Samsung service centre.
No HDMI output.
(DVD-SR275M only)
• Check the Video output is HDMI enabled.
• Check the connection between the TV and the HDMI jack of the DVD Recorder.
• See if your TV supports this 576p/720Pp/1080i/1080p DVD Recorder.
Abnormal HDMI output
screen. (DVD-SR275M
only)
• If snow noise appears on the screen, it means that TV does not support HDCP
(Highbandwidth Digital Content Protection).
HDMI output Jitter
(DVD-SR275M only)
• Check your TV system setup correctly.
• Screen Jitter may occur when the frame rate is converted from 50Hz to 60Hz for 720p/1080i/
1080p HDMI (High Definition Multimedia Interface) Output.
• Please refer to the user’s manual of your TV.
English - 79
Reference
No progressive
output.
Specifications
General
Input
Power requirements
220 - 240 VAC, 50Hz
Power consumption
23 Watts/3Watts(Power off )
Weight
2.3Kg
Dimensions
430(W) x 218(D) x 59(H)
Operating temp.
+5°C to +35°C
Other conditions
Keep level when operating. Less than 75% operating humidity
Video
Composite Video : 1.0 V p-p at 75Ω load, sync negative
Audio
Max.Audio Input Level : 2 Vrms
DV Input
IEEE 1394(4p) compatible jack
Receivable Channels
PAL-B/G, D/K, I, SECAM-L/L’, DVB-T
Scart Jack
Video : Composite, RGB, Audio: analogue
AV2 (Scart Ext)
Analogue output jacks x 2
Audio
Coaxial digital audio output
Composite Video : Video output jack x 1
Output
Video
Component output x 1 (Y : 1,0Vp-p, PB : 0,70Vp-p, PR : 0,70Vp-p at 75Ω load)
HDMI output [480p, 720p, 1080i, 1080p] (DVD-SR275M only)
Scart Jack
Recording
AV1 (Scart TV)
Video : Composite, RGB, Audio: analogue
Audio frequency
characteristics
20Hz-20KHz
Picture Compression format
MPEG-II
Audio Compression format
Dolby Digital 2ch/256Kbps, MPEG-II
Recording Quality
HQ(Approx. 1 hour), HSP(Approx. 1 hour 30 minutes), SP(Approx. 2 hours),
LSP(Approx. 2 hours 30 minutes), ESP(Approx. 3 hours), LP(Approx. 4 hours),
EP(Approx. 6 hours), SLP(Approx. 8 hours)
Audio Output
For DVD discs, audio signals recorded at 96 kHz sampling frequency are converted into and output at
48 kHz.
DVD
AUDIO CD(CD-DA)
Analogue Audio Output
48 / 96 kHz
44,1 kHz
Digital Audio Output
48 kHz
44,1 kHz
Reference
Disc Type
English - 80
UNITED KINGDOM
This Samsung product is warranted for the period of
twelve (12) months from the original date of
purchase, against defective materials and
workmanship. In the event that warranty service is
required, you should return the product to the retailer
from whom it was purchased.
However, Samsung Authorised Dealers and
Authorised Service Centres in other EC Countries will
comply with the warranty on the terms issued to
purchasers in the country concerned.
In case of difficulty, details of our Authorised Service
Centres are available from:
Samsung Electronics U.K. Ltd.
Customer Care Centre
PO Box 17243
Edinburgh, EH11 4YB
United Kingdom
Tel : 0870 SAMSUNG (7267864),
Fax : 0870 7221127 (United Kingdom)
Tel : 0818 717 100,
Fax : +44 (0)870 7221127 (Republic of Ireland)
Web : www.samsung.com/uk
„ WARRANTY CONDITIONS
1. The warranty is only valid if, when warranty service
is required, the warranty card is fully and properly
completed and is presented with the original invoice
or sales slip or confirmation, and the serial number
on the product has not been defaced.
2. Samsung’s obligations are limited to the repair or,
at its discretion, replacement of the product or the
defective part.
3. Warranty repairs must be carried out by Authorised
Samsung Dealers or Authorised Service Centres.
No re-imbursement will be made for repairs carried
out by non Samsung Dealers and, any such repair
work and damage to the products caused by such
repair work will not be covered by this warranty.
REPUBLIC OF
IRELAND
4. This product is not considered to be defective
in materials nor workmanship by reason that it
requires adaptation in order to conform to national
or local technical or safety standards in force in
any Country other than the one for which the
product was originally designed and manufactured. This warranty will not cover, and no
re-imbursement will be made for such adaptation
nor any damage which may result.
5. This warranty covers none of the following:
a) Periodic check ups, maintenance and repair or
replacement of parts due to normal wear and
tear.
b) Cost relating to transport, removal or installation
of the product.
c) Misuse, including the faiure to use this product
for its normal purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts
of God, War, Public Disturbances, incorrect
mains voltage, improper ventilation or any other
cause beyond the control of Samsung.
6. This warranty is valid for any person who legally
acquired possession of the product during the
warranty period.
7. The consumers statutory rights in any applicable
national legislation whether against the retailer
arising from the purchase contract or otherwise
are not affected by this warranty. Unless there is
national legislation to the contrary, the rights under
this warranty are the consumers sole rights and
Samsung, its subsidiaries and distributors shall
not be liable for indirect or consequential loss or
any damage to records, compact discs, videos
or audio taper or any other related equipment or
material.
SAMSUNG ELECTRONICS (U.K.) LTD.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.
Region
North America
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CIS
Asia Pacific
Middle East &
Africa
Web Site
DENMARK
FINLAND
FRANCE
3260 SAMSUNG (€ 0,15/Min),
08 25 08 65 65 (€ 0,15/Min)
www.samsung.com
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
SOUTH AFRICA
U.A.E
01805 - SAMSUNG(726-7864) (€ 0,14/Min)
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
0035 (0)2 261 03 710
0900-SAMSUNG(726-7864) (€ 0,10/Min)
815-56 480
0 801 801 881 , 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902 10 11 30
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
800-7267
800-7267
1300 362 603
0800SAMSUNG(726-7864)
800-810-5858 , 010-6475 1880
3698-4698
3030 8282 , 1800 110011
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232 , 02-689-3232
0800-329-999
1 800 588 889
444 77 11
0860-SAMSUNG(726-7864 )
800-SAMSUNG (726-7864), 8000-4726
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/be
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com
www.samsung.com/se
www.samsung.com
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.com
www.samsung.kz
www.samsung.uz
CZECH REPUBLIC
Europe
Customer Care Centre 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421 , 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
0032 (0)2 201 24 18
844 000 844
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka
Vyskočilova 4, 14000 Praha 4
70 70 19 70
030-6227 515
www.samsung.com/ca
www.samsung.com
www.samsung.com
www.samsung.com/ar
www.samsung.com
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com
www.samsung.com/nz
www.samsung.com
www.samsung.com/hk
www.samsung.com
www.samsung.com
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com
www.samsung.com
www.samsung.com/tw
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
AK68-01575A