SignaMax 10/100 to 100FX Industrial PoE Media Converters User`s guide

Signamax Connectivity Systems

10/100BaseT/TX to 100BaseFX

Industrial PoE Converter Series

U

S E R

’

S

G

U I D E

Signamax Connectivity Systems

10/100BaseT/TX to 100BaseFX

Industrial PoE Converter Series

User’s Guide

Signamax 10/100TX to 100FX Industrial PoE Media Converter

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Signamax

 Connectivity Systems from Advanced Electronic

Supports Products Inc. All rights reserved. All brand names are registered trademarks of their relative holders.

Trademarks

Product names mentioned in this manual may be trademarks or registered trademarks of those products and are hereby acknowledged.

 Ethernet is a trademark of Xerox Corporation.

 Microsoft Windows is a trademark of Microsoft Corporation.

 Signamax  is a trademark of Advanced Electronic Support Products, Inc.

User’s Manual

1

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Preface

This manual describes how to install and use the Signamax



Industrial PoE Media Converter. The Signamax

 Industrial

PoE Media Converter introduced here provides one channel media conversion between 10/100BaseT/TX and 100BaseFX.

A member of the growing family of Industrial Media

Converters, this Industrial PoE Media Converter addresses a need for a Power over Ethernet (PoE) Media Converter.

Capable of operating at temperature extremes of 14℉ to

+140 ℉ (-10℃ to +60℃), this is the Media Converter of choice for harsh environments.

The 10/100BaseT/TX port on this Media Converter supports

IEEE802.3af Power over Ethernet (PoE) Power Sourcing

Equipment (PSE) and can detect an IEEE802.3af compliant

Powered Device (PD). Using external 48~52VDC power inputs through Terminal Block or Power Jack, data and power can be transmitted to a Powered Device (PD) over the same twisted-pair Ethernet cable through 10/100BaseT/TX port on the Media Converter.

Or the 10/100BaseT/TX port on this Media Converter supports 30W High Power PoE Power Sourcing Equipment

(PSE) and can detect a 30W High Power PoE compliant

Powered Device (PD). Using external 52~57VDC power inputs through Terminal Block or Power Jack, data and power can be transmitted to a Powered Device (PD) over the same twisted-pair Ethernet cable through 10/100BaseT/TX port on the Media Converter.

The Signamax

 Industrial PoE Media Converter fully complies with IEEE802.3 10BaseT and IEEE802.3u

100BaseTX/FX standards.

In this manual, you will find:

2

User’s Manual

Signamax 10/100TX to 100FX Industrial PoE Media Converter

 Product overview

 Features on the media converter

 Illustrative LED functions

 Installation instructions

 Specifications

User’s Manual

3

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Table of Contents

FCC W ARNING ............................................................. 1

CE M ARK W ARNING ..................................................... 1

T RADEMARKS ............................................................... 1

P REFACE ....................................................................... 2

T ABLE OF C ONTENTS .................................................... 4

P RODUCT O VERVIEW .................................................... 5

I NDUSTRIAL P O E M EDIA C ONVERTER ................... 5

P ACKING C ONTENTS ........................................... 5

P RODUCT H IGHLIGHTS ........................................ 6

F RONT P ANEL D ISPLAY ....................................... 7

P HYSICAL P ORTS ............................................... 8

I NSTALLATION .............................................................. 9

S ELECTING A S ITE FOR THE E QUIPMENT ............... 9

W IRING D IAGRAM ............................................... 9

DIN R AIL M OUNTING ........................................ 10

C ONNECTING TO P OWER ................................... 10

DIP S WITCH ..................................................... 11

C ONNECTING TO Y OUR N ETWORK ...................... 12

S PECIFICATIONS .......................................................... 13

C ONTACT I NFORMATION ............................................. 14

4

User’s Manual

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Product Overview

Industrial PoE Media Converter

Packing Contents

When you unpack this product package, you will find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to our authorized reseller.

 The Media Converter

 User’s Manual

 External Power Adaptor & Power Cord (optional)

User’s Manual

5

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Product Highlights

Basic Features

 Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.

 Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing

Equipment (PSE) or supports 30W High Power PoE Power Sourcing

Equipment (PSE).

 DIP Switch configuration for “Link Fault Signaling”, speed, duplex mode.

 Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,

Full/Half-duplex, Auto-Negotiation, Auto MDI/MDIX.

 100BaseFX: Multi/Single mode SC or ST type, 100BaseBX: WDM

Multi/Single mode SC type.

 Supports 1024 MAC addresses. Provides 2.25M bits buffer memory.

 Power Supplies: Redundant 48VDC or -48VDC Terminal Block power input and 48VDC DC JACK with 100-240VAC external power supply.

 Field Wiring Terminal Markings: Use Copper Conductors Only, 140/167℉

(60/75℃), wire range 12-24 AWG, torque value 7 lb-in.

 Operating voltage and Max. current consumption: 0.075A @ 48VDC.

Power consumption: 3.6W Max.

 Supports up to 15.4W: Redundant 48 to 52VDC Terminal Block power input and 48 to 52VDC DC JACK.

 Operating voltage and Max. current consumption when PoE link with

15.4W IEEE802.3af PD: 0.4A @ 48VDC. Power consumption: 19.2W Max.

 Supports up to 30W: Redundant 52 to 57VDC Terminal Block power input and 52 to 57VDC DC JACK.

 Operating voltage and Max. current consumption when PoE link with 30W

High Power PD: 0.62A @ 55VDC. Power consumption: 34.1W Max.

 For use in Pollution Degree 2 Environment.

 Supports DIN-Rail, Panel, or Wall Mounting installation.

6

User’s Manual

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Front Panel Display

Status LEDs

LEDs State

Power over Ethernet (PoE)

PoE Steady

Off

Indication

Powered Device (PD) is connected.

Powered Device (PD) is disconnected.

10/100BaseT/TX, 100BaseFX/BX

Link/ACT Steady A valid network connection established.

Flashing Transmitting or receiving data.

ACT stands for ACTIVITY.

User’s Manual

7

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Physical Ports

This Media Converter provides:

One 10/100BaseT/TX port + one 100BaseFX/BX port

Connectivity

 RJ-45 connectors.

 SC or ST connector on 100BaseFX fiber port.

 SC connector on 100BaseBX fiber port.

8

User’s Manual

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Installation

This chapter gives step-by-step installation instructions for the Converter.

Selecting a Site for the Equipment

As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements:

 The ambient temperature should be between 14 and 140 degrees

Fahrenheit (-10 to 60 degrees Celsius).

 The relative humidity should be less than 95 percent, non-condensing.

 Surrounding electrical devices should not exceed the electromagnetic field

(RFC) standards.

 Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes on each side of the equipment.

 The power outlet should be within 1.8 meters of the product.

Wiring Diagram

Field Wiring Terminal Markings: Use Copper Conductors

Only, 140/167℉ (60/75℃), wire range 12-24 AWG, torque value 7 lb-in.

User’s Manual

9

Signamax 10/100TX to 100FX Industrial PoE Media Converter

DIN Rail Mounting

 Fix the DIN rail attachment plate to the back panel of the Media Converter.

 Installation: Place the Media Converter on the DIN rail from above using the slot. Push the front of the Media Converter toward the mounting surface until it audibly snaps into place.

 Removal: Pull out the lower edge and then remove the Media Converter from the DIN rail.

Connecting to Power

Redundant DC Terminal Block Power Input and DC Jack:

DC Terminal Block Power Input

 Connect the DC power cord to the plug-able terminal block on the Media

Converter, and then plug it into a standard DC outlet.

 Disconnect the power cord if you want to shut down the Media Converter.

DC Jack

 Connect the supplied AC to DC power adapter to the receptacle on the

Media Converter.

 Connect the power cord to the AC to DC power adapter and attach the plug into a standard AC outlet with the appropriate AC voltage.

10

User’s Manual

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Power Input Assignment (30W High Power PoE model)

Power 1

＋

48~52VDC for 15.4W

52~57VDC for 30W

－ Power Ground Terminal Block

Power 2

DIP Switch

Earth Ground

48~52VDC for 15.4W

52~57VDC for 30W

DC Jack

There are four pins on the DIP switch for port settings. Refer to the table below for more details.

DIP

On Off

Switch

1

2

3

4

Enable forced mode for

10/100BaseT/TX port

10/100BaseT/TX port forced to

10Mbps

10/100BaseT/TX port forced to half duplex mode

Enable Link Fault Signaling

Enable auto negotiation for

10/100BaseT/TX

10/100BaseT/TX port forced to

100Mbps

10/100BaseT/TX port forced to full duplex mode

Disable Link Fault Signaling

User’s Manual

11

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when connecting the Media Converter to your network. Use appropriate cables that meet your speed and cabling requirements.

Cable Specifications

Speed

10BaseT

100BaseTX

100BaseFX

100BaseFX

Connector Port Speed

Half/Full

Duplex

RJ-45

RJ-45

SC, ST

SC, ST

Cable

10/20 Mbps 2-pair UTP/STP Cat.

3, 4, 5

100/200

Mbps

200 Mbps

200 Mbps

2-pair UTP/STP Cat.

5

MMF (50 or 62.5μm)

SMF (9 or 10μm)

100BaseBX SC

100BaseFX SC

200 Mbps

200 Mbps

MMF (50 or 62.5μm)

SMF (9 or 10μm)

Max.

Distance

100 m

100 m

2 km

20, 40, or 75 km

2 or 5 km

20 or 40 km

Cabling

 First, ensure the power of the Media Converter and end devices are turned off.

<Note> Always ensure that the power is off before any installation.

 Prepare cable with corresponding connectors for each type of port in use.

 Consult the previous section for cabling requirements based on connectors and speed.

 Connect one end of the cable to the Media Converter and the other end to a desired device.

 Once the connections between two end devices are made successfully, turn on the power and the Media Converter is operational.

12

User’s Manual

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Specifications

Industrial PoE

Media Converter

Applicable Standards

Switching Method

Forwarding Rate

10BaseT:

100BaseTX:

100BaseFX/BX:

Performance

Cable

10BaseT:

100BaseTX:

100BaseFX/BX:

LED Indicators

Dimensions

Net Weight

Power Consumption

Operating Voltage &

Max. Current

Consumption

Power

10/100BaseT/TX auto-negotiating port with RJ-45 connector, 100BaseFX/BX fiber port

IEEE 802.3 10BaseT

IEEE 802.3u 100BaseTX/FX

Store-and-Forward

10 / 20Mbps half / full-duplex

100 / 200Mbps half / full-duplex

200Mbps full-duplex

14,880pps for 10Mbps

148,810pps for 100Mbps

4-pair UTP/STP Cat. 3, 4, 5

4-pair UTP/STP Cat. 5

Up to 328ft (100m)

MMF (50 or 62.5μm), SMF (9 or 10μm)

Per unit –

Power status (Power 1, Power 2)

PoE status (PoE)

Per port –

10/100TX or 100FX/BX - Link/ACT

2.76” (W) × 4.33” (D) × 1.18” (H)

(70mm (W) × 110mm (D) × 30mm (H))

0.55lb. (0.25Kg)

3.6W Max.

0.075A @ 48VDC

Operating Voltage &

Max. Current

Consumption

Power Consumption

Operating Temperature

Storage Temperature

Humidity

Safety

Supports up to 15.4W: 48~52VDC

Supports up to 30W: 52~57VDC

When PoE link with 15.4W IEEE802.3af PD:

0.4A @ 48VDC

When PoE link with 30W High Power PD:

0.62A @ 55VDC

When PoE link with 15.4W IEEE802.3af PD:

19.2W Max.

When PoE link with 30W High Power PD:

34.1W Max.

14℉ to 140℉ (-10℃ to 60℃)

-40℉ to 185℉ (-40℃ to 85℃)

5%-95% non-condensing

UL508

User’s Manual

13

Signamax 10/100TX to 100FX Industrial PoE Media Converter

Contact Information

SIGNAMAX

 CONNECTIVITY SYSTEMS

An AESP Company

999 N.W. 159th Drive

Miami, Florida 33169, U.S.A.

Phone: 305-944-7710 Fax: 305-949-4483

Sales: 800-446-2377 Tech. Support: 800-446-

2377, ext. 201

Http://www.signamax.com

E-mail: [email protected]

14

User’s Manual