Craftsman 320.22335 Operator`s manual

Operator's
Manual
Universal Bench-Top-Tool
Adjustable Work Stand
Model No. 320. 22335
CAUTION! Read, understand and
follow all Safety Rules and Operating
Instructions in this Manual before
using this product.
I Sears Brands Management
Hoffman Estates, IL 60179
www.craftsman.com
Corporation,
•
•
•
•
•
•
WARRANTY
SAFETY
UNPACKING
ASSEMBLY
DESCRIPTION
MAINTENANCE
I
i f_1:] ml_ [o_ [_o_ili_i_
Warranty
Page 2
Safety Symbols
Page 3
Safety Instructions
Pages 4-10
Unpacking
Page 10
Description
Page 11
Assembly
Pages 12-18
Maintenance
Page 19
Parts list
Pages 20-22
Sears Repair Parts Phone Numbers
Back Cover
ONE YEAR FULL WARRANTY ON CRAFTSMAN ®
PROFESSIONAL PRODUCT
If this Craftsman product fails due to a defect in material or workmanship
within one year from the date of purchase, RETURN IT TO THE NEAREST
SEARS STORE OR PARTS AND REPAIR CENTER OR OTHER
CRAFTSMAN
OUTLET IN THE UNITED STATES FOR FREE REPAIR(or
replacement if repair proves impossible).
This warranty does not include expendable
bits or blades.
parts such as lamps, batteries,
This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
Sears, Roebuck
and Co., Hoffman
Estates,
IL 60179
A
WARNING:Some
dust created by using power tools contains chemicals
known to the state of California to cause cancer and birth defects or other reproductive harm.
SAVE THESE INSTRUCTIONSZ
READ ALL INSTRUCTIONSZ
22335
ManualRevised
07-1203
Page 2
The purpose of safety symbols is to attract you attention to possible dangers.
The safety symbols, and the explanations with them, deserve your careful
attention and understanding.
The symbol warnings do not by themselves
eliminate any danger. The instructions and warning they give are no substitutes
for proper accident prevention measures.
_,
WARNING:
BE SURE to read and understand
all safety instructions
in this
manual, including all safety alert symbols such as "DANGER," "WARNING," and
"CAUTION," BEFORE using this tool stand. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
SYMBOL
_,
MEANINGS
SAFETY ALERT SYMBOL:
May be used in conjunction
_,
DANGER:
Indicates
DANGER, WARNING,
with other symbols
OR CAUTION.
or pictographs.
Failure to obey this safety warning WILL result in death or serious
injury to your or to others. Always follow the safety precautions
of fire, electric shock and personal injury.
to reduce the risk
_, WARNING: Failure to obey this safety warning CAN result in death or serious
injury to your or to others. Always follow the safety precautions to reduce the risk
of fire, electric shock and personal injury.
_,
CAUTION:
Failure to obey this safety warning MAY result in death or serious
injury to your or to others. Always follow the safety precautions
of fire, electric shock and personal injury.
to reduce the risk
DAMAGE PREVENTION AND INFORMATION MESSAGES
These inform user of important information and/or instructions that could lead to
equipment or other property damage if not followed. Each message is preceded
by the word "NOTE:" as in the example below:
NOTE: Equipment
not followed.
and/or property
_,
WEARYOUR
22335
Manual
Revised 07-1203
damage
WARNING:
may result if these instructions
The operation
are
of any bench top tool can
result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power
tool operation, ALWAYS wear safety goggles or safety
glasses with side shield and a full-face shield when
needed. We recommend a Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side
shield, available at Sears Stores or other Craftsman outlets.
Page 3
[.-"Y'-I
iI zlll'4 I1_(.._ij_ll_]ij[e]]_.._
_i, WARNING:Be sure to read, understand and follow all Safety rules and operating instructions in this Manual and the operator's manual of any bench top power
tool you use with this Adjustable Work Stand. Failure to do so may result in electric
shock, fire and/or serious personal injury.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered
and dark areas invite accidents.
Do not operate power tools in explosive environments,
such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
Keep children and bystanders
and visitors
Distractions can cause you to lose control.
Make your workshop
childproof
tools away when not in use.
away while operating
with padlocks
a power tool.
and master switches.
Lock
Make sure the work area has ample lighting so you can see the work and that
there are no obstructions that will interfere with safe operation before using your
bench top power tool and your adjustable work stand.
PERSONAL SAFETY
Know your adjustable work stand and the bench top power tool you are using with
it. Learn the applications, limitations, and the specific potential hazards related to
this adjustable work stand and the bench top power tools you use with it.
Stay alert, watch what you are doing and use common sense when operating
power tool that is mounted to this adjustable work stand
a
Do not use a power tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in
serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Pull back long hair. Keep
your hair, clothing and gloves away from moving parts. Loose clothing or long
hair can be caught in moving parts. Air vents often cover moving parts and
should also be avoided.
_i,
WARNING:
Make sure that this adjustable
work stand is properly
set up and
that the bench top power tool you are using with it is properly attached to the
tabletop assembly. Failure to follow all instructions listed on pages 12 through 16
may result in electric shock, fire and/or serious personal injury.
Avoid accidental
starting
of tools. Be sure switch is in "OFF" position before
plugging the tool into a power source. DO NOT carry tools with your finger on
the switch. Carrying tools with your finger on the switch or plugging in tools that
have the switch in the "ON" position invites accidents.
22335
ManualRevised
07-1203
Page 4
Remove adjusting keys or blade wrenches
before turning the tool "ON."
A wrench that is left attached to a rotating part of the tool may result in
personal injury.
De not overreach.
Keep proper footing and balance at all times. Proper footing
and balance enables better control of the tool in unexpected situations.
Always secure your work. Use clamps or a vise to hold work when practical.
safer than using your hand and frees both hands to operate tool.
It is
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, and hearing protection must be used for appropriate conditions.
Always be sure that the adjustable work stand is set up on a flat solid surface. This
enables better control of the power tool that is attached to the work stand.
TOOL USE AND CARE SAFETY
_.
WARNING:
Be sure to read, understand,
and follow all safety rules and
operationg instructions in this manual and in the operator's manual of any bench
top power tool you use with this work stand.Failure to do so may result in electric
shock, fire, and/or serious personal injury.
Always use clamps or other practical ways to support and secure the
workpiece to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
De not force the power tool. Use the correct tool and accessories
for your
application.
The correct tool and accessories
will do the job better and more
safely at the rate for which it is designed.
De not use the tool if the switch does not turn
cannot be controlled with the switch is dangerous
it "ON" or "OFF." Any tool that
and must be repaired.
Disconnect the plug from the power source before making any
adjustments,
changing accessories, or storing the tool. Such preventive
measures reduce the risk of starting the tool accidentally.
Never leave the tool running.
comes to a complete stop.
safety
Always turn it off. Do not leave the tool until it
Store idle tools out of the reach of children
Tools are dangerous in the hands of untrained
and other untrained
users.
persons.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with sharp cutting edges are less likely to bind and are
easier to control.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool's operation. If damaged, have the tool
serviced before using it. Many accidents are caused by poorly maintained tools.
22335
ManualRevised
07-1203
Page 5
Use only accessories that are recommended
for the tool being used.
Accessories that may be suitable for one tool may become hazardous when
used on another tool.
ELECTRICAL SAFETY
Grounded tools
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk electric shock. This stand is
equipped with an electrical cord that has an equipment-grounding
conductor and
a grounding plug. The plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit into the outlet, have the proper
outlet installed by a qualified electrician.
Improper connection of the equipment-grounding
conductor can result in a risk
of electric shock. The conductor with a green-colored
outer insulation cover,
with or without yellow stripes, is the equipment-grounding
conductor. If repair or
replacement is necessary, do not connect the equipment-grounding
conductor
to a live terminal.
Check with a qualified electrician or service personnel if the grounding
instructions are not completely understood, or if in doubt as to whether
is properly grounded.
Use only 3-wire extension cords that have 3-prong
receptacles that accept the tool's plug.
Repair or replace a damaged
use on a circuit that has an
outlet that looks like the one
illustrated in Sketch A in the
grounding
or worn cord immediately.
the tool
plugs and 3-pole
This tool is intended
for
figure to the right. The tool
Metal
has a grounding plug that
looks like the plug illustrated
in sketch A in the figure to the
_C._cLn_ingPin
_<c_
right. A temporary adapter,
which looks like the adapter
illustrated in Sketch B and C,
C,
Outlet Box
may be used to connect this
Cover of Grounded
plug to a 2-pole receptacle,
Grounding Means
as shown in Sketch B, if a
properly grounded outlet is
not available. The temporary
adapter should be used only until a properly grounded outlet can be installed by
a qualified electrician. The green-colored
rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent ground, such as a properly
grounded outlet box.
22335
ManualRevised
07-1203
Page 6
Use the proper extension
cord.
Make sure that your extension
cord is good condition.
When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Minumum
Volts
Gauge for Extension Cords
Total Length of Cord in Feet
120V
25ft.
50ft.
100ft.
150ft.
Ampere Rating
AWG
AWG
AWG
AWG
More than 0
Not more than 6
18
16
16
14
More than 6
Not more than 10
18
16
14
12
More than 10
Not more than 12
16
16
14
12
More than 12
Not more than 16
14
12
Not Recommended
Circuit Breaker
Your adjustable work stand is equipped with a manual-reset, switch-assembly
overload protector. The overload protector is designed to stop the current to the
switch assembly when the switch assembly current exceeds a safe level.
When the switch assembly
is overloaded,
the circuit breaker will trip.
After cooling to a safe operating temperature, the circuit breaker can be reset by
pressing the circuit breaker button on the side of the switch assembly.
SAFETY SYMBOLS FOR YOUR TOOL
V ..................................................... Volts
A ...................................................... Amps
Hz.................................................... Hertz
W..................................................... Watts
min.................................................. Minutes
"_
.............................................. Alternating current
................................................
no
[]
Direct current
............................................... No-load speed
.................................................. Class II construction, Double Insulated
.../min ............................................... Revolutions or Strokes per minute
.............................................. Indicates danger, warning or caution. It means
attention! Your safety is involved.
22335 Manual Revised 0L1203
Page 7
SAFETY FOR THE ADJUSTABLE WORK STAND
Always set up the adjustable
work stand on a hard, dry, flat, stable surface.
Be sure that the adjustable work stand is fully opened and locked into the
proper "set-up" position before mounting your bench-top power tool to the
tabletop assembly.
Follow all set-up
instructions
Always
attach
properly
on pages 12 through 15 in this operator's
the bench-top
manual.
power tool to the stand.
Do not attempt to use your work stand with a power tool until the tool is bolted
securely to the tabletop assembly according to the instructions on page 16 in
this operator's manual.
Always follow all safety rules and instructions in the product manual for the power
tool when operating a power tool that is mounted on the adjustable work stand.
Always be that sure you have the proper space around the adjustable work
stand to safely operate the power tool when setting up your adjustable work
stand with a power tool
Always check the adjustable work stand and power tool for damaged parts. If
any part is damaged, it should be carefully checked to determine if it will operate
properly and perform its intended function before further use of the adjustable
work stand or the tool,
Keep your hands
away from the cutting,
drilling,
or sanding area.
Always use clamps or a vise to hold the workpiece when practical. Using
clamps or a vise to hold the workpiece is safer than using your hand. It also
frees up both hands to operate the bench-top tool.
Avoid awkward operations and hand positions where a sudden slip could cause
your hand to move into the cutting, drilling, or sanding area of the tool.
Never sit, stand, or climb on this adjustable work stand. It is not designed or
constructed to accommodate this type of use. It could tip over, causing serious injury.
Do not store any items above or near the adjustable
it is set up with a power tool attached.
Never use this adjustable
ADDITIONAL
WARNING:
work stand, especially
when
work stand as a ladder or scaffold.
RULES FOR SAFE OPERATION
BE SURE to read and understand
all instructions
in this Manual
and the Tool's Operating Manual before using the tool on this adjustable work
stand. Failure to follow all instructions listed below may result in electric shock,
fire and/or serious personal injury.
Know your Adjustable Work Stand and the power tool you are using with it. Read
both operators' manuals carefully. Learn the applications and limitations, as well as
the specific potential hazards related to the tool mounted on the adjustable work
stand. Following this rule will reduce the risk of electric shock, fire or serious injury.
ALWAYS wear safety glasses or eye shields when using power tools. Everyday
eyeglasses have only impact-resistant
lenses; they are NOT safety glasses.
22335
ManualRevised
07-1203
Page 8
Protect your lungs. Wear a face mask or dust mask if the operation
is dusty.
Protect your hearing. Wear appropriate personal hearing protection during use.
Under some conditions, noise from power tools may contribute to hearing loss.
All visters and bystanders
must wear the same safety equipment
operator of the tool should wear.
that the
Inspect the tool cords periodically and, if damaged, have them repaired at your
nearest Sears Service Center. Be aware of the cord location.
Always check the adjustable work stand and the power tool you are using with
it for damaged parts. Before further use of the tool, a guard or other part that
is damaged should be carefully checked to determine if it will operate properly
and perform its intended function. Check for misalignment or binding of moving
parts, breakage of parts, and any other condition that may affect the tool's
operation. A guard or other part that is damaged should be properly repaired or
replaced at a Sears Service Center.
Inspect
and remove
all nails from lumber before using a power tool.
Always disconnect
the power tool from the power supply before attaching it to
this work stand. Make sure that the switch is off when reconnecting the tool to a
power supply.
Before
making
a cut, be sure all adjustments
are secure.
Always get help if you need to lift the adjustable work stand. When lifting, hold
the work stand close to your body. Bend your knees so you can lift with your
legs, not your back.
Secure the adjustable
work stand
movement and possible damage.
when transporting
it in a vehicle to prevent
Never put the adjustable work stand where operators or bystanders are forced
to stand with any part of their body inline with the path of the saw blade.
Check to make sure that the adjustable
before using the work stand.
work stand does not rock, slide, or move
Save these instructions.
Refer to them frequently and use them to instruct
others who may use this adjustable work stand. If someone borrows this work
stand, make sure that they also have these instructions.
,_
WARNING:
Some dust created by using power tools contains
known to the state of California
ductive harm.
22335
ManualRevised
07-1203
to cause cancer and birth defects
chemicals
or other repro-
Page 9
Some examples
of these chemicals
•
Lead from lead- based paints.
•
Crystalline
•
Arsenic
silica from bricks
and chromium,
are:
and cement and other masonry
from chemically
treated
products.
lumber.
Your risk from these exposures varies, depending upon how often you do this
type of work. To reduce your exposure to these chemicals:
•
Work in a well-ventilated
area.
•
Work with approved safety equipment, such as those dust marks that are
specially designed to filter out microscopic particles.
After taking the adjustable work stand out of the box, check for misalignment or
binding of moving parts, bending or breakage of parts, and any other condition
that may affect the adjustable work stand's operation. If any part is missing
or damaged, return the adjustable work stand to your nearest Sears store or
Craftsman outlet to have the work stand replaced.
,_,
WARNING:If
any parts are bent or broken, do not attempt to set up the
adjustable work stand. Do not attempt to mount and use any power tool on a
defective work stand.Failure to do so could result in possible serious injury.
22335
ManualRevised
07-1203
Page 10
ID]*'[_]];]_ij[e]_]
This Adjustable Work Stand has the following features:
1.
Setup adjustment
handle with soft grip for easy setup and takedown
2.
Soft-grip
3.
Locking pin support
folded for storage.
4.
Compact
5.
Safety switch with duplex outlet,
6.
Two, 4-in., locking
7.
Adjustable
tabletop
8.
Adjustable
height with positive stops at 28", 30", 32", 34" and 36"
dual handle for comfort
design
during transport
automatically
engages
makes the adjustable
to secure the stand when it is
work stand foldable
over-load
protection,
caster wheels for transport
with two sliding
Fig. 1
and sure grip during use
for easy storage.
and 10-ft. SJT cable.
and stability.
bars for attaching
different
bench tools.
Tabletop Assembly
Setup Adjustment Handle
Switch
box
As-
Caster Wheel
sembly
Clamping
Knobs
Knob
Slide Tube
Adjustable
foot i/o feet
Spring Loaded
Locking Pin
22335
ManualRevised
07-1203
Support
Bar
Page 11
PRODUCT SPECIFICATIONS
Stand Weight
50 Ibs.
Maximum
400 Ibs continuous
Weight Capacity
load capacity
Power Cord Length
10 ft.
Tool Stand Height
28" - 36" (positive stops at 30", 32", 34", 36")
Overall Dimensions,
Fully extended
49 in.(L) x 26 in.(W)x36 in. (H)
E[,.!.I =1_v_
I:] I_'d
UNFOLDING AND SETTING UP THE WORK STAND (Figs.241)
1,
Remove the work stand
from the carton and
Fig. 2
place it flat on floor, as
shown (Fig. 2).
2,
Make sure that the two
locking knobs have been
loosened to the maximum
outside position, take
hold of the setup
adjustment handle, apply
pressure to the support
bar with your foot, and
pull out the spring loaded
locking pin (Fig. 3).
22335 ManualRevised 07-:[203
Page12
3.
With your foot still on
the support bar, lift up
the setup adjustment
handle (Fig. 4).
4.
With your foot still
on the support bar,
continue lifting the setup
adjustment handle to the
height desired. Make sure
that the red lock knob on
Fig. 4
each side is engaged.
5.
With your foot still on the
support bar and your hand
on the setup adjustment
handle to support the
tabletop assembly, tighten
the two red locking knobs
to the maximum inside
position
Fig. 5
(Fig. 5).
Fig. 6
22335
ManualRevised
07-1203
Page 13
NOTE: This work stand may
be adjusted from: 28" - 36" in
height with positive stops at
30", 32", 34", and 36". To adjust the stand's height, turn the
two red locking knobs counter
clockwise to unlock them, then
pull out the left knob and follow steps 3-4.
_,
DANGER:Make
sure
that your hand is always on
the setup adjustment handle
until the two locking knobs are
locked in the holes. Failure to
obey this safety warning WILL
result in the Tabletop Assembly
falling down accidentally, which
may lead to death or serious
injury to yourself or to others.
6.
Fig. 8
To change the width of
the Tabletop Assembly
working area, turn the
tabletop assembly's
four clamping knobs
counterclockwise
to
unlock them (Fig 7. i/o
Fig. 6).
7.
22335
After loosening the tabletop assembly's clamp
knobs, adjust the Tabletop
Assembly to the desired
position to mount your
power tool (Fig.8 i/o
Fig. 7).
ManualRevised
07-1203
Page 14
8.
Be sure that, after adjusting
the width of the tabletop
assembly, you lock the four
clamping knobs by turning
them clockwise until
securely tightened
9.
Fig. 10
(Fig. 9).
Unlock the 4-inch locking
Caster Wheels by lifting
the locking lever on
each wheel to the "UP"
position
(Fig. 10).
10. Lock the Caster wheels
in place by pushing
the locking lever to the
"DOWN "position (Fig. 11).
Fig. 11
NOTE: When the work stand
is on uneven surface, stabilize the stand by adjusting
the adjustable foot (Fig. 11 a)
by turning it clockwise
or counterclockwise.
Fig. 11a
Adjustable Foot
22335
ManualRevised
07-1203
Page 15
ATTACHING
YOUR
WARNING:
BENCH-TOP
WARNING:
(Fig.12)
Failure to
unplug the tool before attaching it to the stand could result in
accidental starting and possibly
serious personal injury.
_,
TOOL TO THE STAND
Fig. 12
Mounting
Holes
To avoid
serious personal injury, always
make sure that bench tools
are fully supported and securely attached to a level work
surface. If necessary, move
the stand to a location where
it will be more stable.
_,
WARNING:
Always check
that all mounting bolts and nuts used to secure a tool to the stand are tightened
before moving the stand or using the tool. Failure to do so could result in serious
personal injury.
To attach tool
1.
Before mounting your bench top tool, make sure the Caster Wheels are in the
"DOWN" or locked position.
2.
Check the bench top tool for the necessary number of holes and their
locations for mounting the tool. This information should be in the manual for
the bench top tool.
3.
Choose the corresponding
mounting hole locations
of the adjustable work stand (Fig. 12).
4.
Change the width of the tabletop assembly as necessary to accommodate the
bench-top tool. To change the width of the tabletop assembly, see steps 6-8 in
Unfolding and Setting Up the Work Stand.
5.
Place the bench-top tool on the tabletop assembly, align the mounting holes
in the bench-top tool with the holes on the tabletop assembly, and use the
bolts recommended
in your bench-top tool's manual to connect them.
22335
Manual
Revised 07-1203
on the tabletop
assembly
Page 16
SWITCH OPERATION
Fig. 13
The switch has a safety key
to help prevent accidentally
switching the tool ON and
the unauthorized,
possibly
hazardous use by others.
The safety key must be
completely inserted into the
switch before the switch panel
can be turned ON.
Two receptacles are located
at the back of the switch
assembly (Fig. 13). One is
intended to supply power to
your tool; the other can supply
power to the a worklight,
vacuum cleaner, or other item.
Fig. 14
The ON/OFF switch panel
controls power to both outlets.
To operate
the switch:
1.
Make sure that the safety
key is inserted into the
switch panel (Fig. 14).
2.
To turn the power ON, lift
up the ON/OFF switch
panel (Fig. 15).
Fig. 15
Panel
22335 ManualRevised 07-;[203
Pasei7
3.
To turn the power OFF,
push the ON/OFF switch
panel down (Fig. 16).
4.
To lock switch
Fig. 16
in the OFF
position, push the ON/
OFF switch panel down
to OFF position, and
remove the safety key
from the switch panel.
WARNING:
Never leave
a tool unattended while it is
running or before it comes to
a complete stop.
Circuit
1
Breaker
I Fig. 17
When the switch-assembly
current exceeds a safe level,
it will overload the circuit,
and the circuit breaker will
I
trip. Press the circuit-breaker
button to reset the switch
assembly
(Fig. 17).
FOLDING WORK STAND
DOWN FOR STORAGE
Please refer to Fig. 1 to Fig 11
on pages 11-15.
NOTE: Remove any
workpieces,
clamps,
or other accessories.
1.
Remove the bench-top
power tool from Work stand.
2.
Keep the Caster Wheels in the locked position
"DOWN" (Fig. 11).
3.
Loosen the work stand's Clamping
4.
Grasp the set-up adjustment
bar with your foot.
5.
With your foot still on the support
pull the left knob out (Fig. 5).
6.
Lower the tabletop
_,
DANGER:
by pushing the Locking Lever
Knobs.
handle while applying
pressure to the support
bar, loosen the two red locking
knobs and
assembly.
Make sure that your foot is always on the support bar until the
Tabletop Assembly is lowered completely. Failure to obey this safety warning WILL
result in the Support Bar springomg up accidentally, which that may lead to death or
serious injury to yourself or to others.
22335
Manual
Revised 07-1203
Page 18
This adjustable work stand has been designed to be low-maintenance.
in order to maintain its performance,
follow these steps.
However,
1.
Handle the adjustable work stand with care. Do not drop, throw, or otherwise
mistreat the work stand. Use it only for its intended purpose.
2.
Do not allow the adjustable
stored in a dry place.
3.
In order to keep the adjustable work stand working properly, keep it clean.
Wipe dust and debris from the tabletop and the telescoping legs with a
damp cloth to insure proper working order.
22335
ManualRevised
07-1203
work stand to become and remain wet. Keep it
Page 19
I",2.-_
-'#_ I_,.1JJ
Universal Bench-Top-Tool
MODEL NUMBER
Adjustable
Work Stand
320.22335
Always mention the Model Number when ordering
3
P
parts for this tool.
i
,\
\\
_o
33
Sl
i 4
4O
/
4i
/
/
3_8/
22335
Manual
Revised 07-1203
Page 20
Universal
Bench-Top-Tool
MODEL NUMBER
Adjustable
Work Stand
320.22335
Always mention the Model
Number when ordering
parts for this tool.
1
LA0200021
25mm Table Pull Rod
2
2
LC0000021
Sliding Bush
4
3
LE0100021
Moving Steel Board (printed)
1
4
LC0000022
Fixing Bush
4
5
LC0000023
Locking Nut
4
6
LC0000024
Clamping Knob
4
7
LIO200021
Bolt M6x75mm
6
8
LIO200022
Bolt M6X40mm
13
9
LC0000025
Block Cap
6
10
LE0100022
Small Bracket Assembly
1
11
LC0000026
25mm Bracket Cap
1
12
LA0100021
Setup Adjustment Handle
1
13
LIO200023
Nylon-Locknut
6
14
LA0100022
28mm Sliding Tube
2
15
LB0200021
Left Locking Rod
1
16
LE0100023
Sliding Bracket Assembly
1
17
LE0100024
Large Bracket Assembly
2
18
LB0200022
Right Locking Rod
1
19
LL0500021
Compression Spring
2
20
LB0200023
Clamp
2
21
LC0000027
Locking Knob
2
22
LC0000028
End Cover
12
23
LC0000029
Cable Hook
2
24
LIO200024
Hex Bolt M6X70mm
2
25
LC0000030
28.8mm Bracket Cap
2
26
LC0000031
23mm Bracket Cap
4
27
LE0100025
Moving Steel Board
1
28
LJ0000021
Switch Assembly
1
22335
ManualRevised
07-1203
M8
Page 21
29
LIO200025
Bolt M6X14mm
3
30
LC0000032
Lower Support Cover
4
31
LC0000033
Left Block
1
32
LE0100026
Inner Bracket Assembly
1
33
LL0500022
Handle Spring
1
34
LIO200026
Flat Washer M8
16
35
LC0000034
Spring-loaded
1
36
LB0200024
Pin
1
37
LC0000035
Rubber Support bar
2
38
LE0100027
Support bar
1
39
LIO200027
Nut M6
34
40
LIO200028
Bolt M6X35mm
8
41
LC0000036
Rubber Foot
4
42
LIO200029
Washer
67
43
LIO200030
Axle M6x20mm
4
44
LC0000037
Right Block
1
45
LA0200022
Angle Block
1
46
LIO200031
Bolt M6X25mm
2
47
LC0000038
Bush
8
48
LA0100023
Inner Bracket Tube
1
49
LE0100028
Outer Bracket Assembly
1
50
LB0200025
Center Pull Rod
1
51
LC0000039
Protection Jacket of Nut
10
52
LG0000021
4" Wheel
1
53
LG0000022
4" Wheel ( W/Adjustble
Locking
Pin Assembly
22335
ManualRevised
07-1203
Foot)
1
Page 22
I_,]iii_,.-]
22335
Manual
Revised 07-1203
Page 23
Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it !
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
Ca, anytime, day or night
(1-800-469-4663)
(U.S.A. and Canada)
www.sears.com
www.sears.ca
ourHome
_
ii
For repair of carry-in items like vacuums lawn equipment
and electronics call anytime for the location of the nearest
Sears Parts & Repair Service Center
1"800-488-1222 (U.S.A.)
1"800"469-4663 (Canada)
www.sears.com
ii
www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
:::i:
1-800-827-6655
(U.S.A.)
1-800-361-6665
(Canada)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR®
Au Canada pour serv ce en franq,a s
1.800.LE.FOYERMC
(1-800-533-6937)
( 1- 888 . 784-6427 )
www • sears . ca
Sealr
© Sears Brands, LLC
® Registered Trademark / TMTrademark / SMService Mark of Sears Brands, LLC
® Marca Registrada / TMMarca de Fabrica / SMMarca de Servicio de Sears Brands, LLC
MCMarque de commerce
/ MDMarque d6pos6e de Sears Brands,
LLC
::