ESPRIT X6 Operating instructions

33333
INSTALER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
WARNING: If the information in these
instructions is not followed exactly a fire or
explosion may result causing property
damage, personal injury or death.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapours and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS





Do not try to light any appliance.
Do not touch any electrical Switch.
Do not use any phone in your building.
Immediately call your gas supplier
from a neighbour’s phone. Follow the
gas supplier’s instructions.
If you cannot reach your gas supplier
call the fire department.
LINEAR GAS FIREPLACE
INSTALLATION AND
OPERATING INSTRUCTIONS
Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
This appliance may be installed in an
aftermarket permanently located,
manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type of
gas indicated on the rating plate. This
appliance is not convertible for use with
other gases unless a certified kit is used.
This appliance is suitable for installation in a
bedroom or bed sitting room.
090314
ESPR.BODYA
MODEL: ESPRIT
ESPR.BODYA
ZERO CLEARANCE FIREPLACE
5056.201
Important Note for the Commonwealth of Massachusetts:
From Massachusetts Rules and Regulations 248 CMR 5.08:
(a) For all side wall horizontally vented gas fuelled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven
(7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied.
1.
INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fuelled equipment,
the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the
floor level where the gas equipment is to be installed, in addition, the installing plumber or gas fitter shall observe that a battery operated or hardwired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall
horizontal vented gas fuelled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals
for the installation of hard-wired carbon monoxide detectors.
a.
In the event that the side wall horizontally vented gas fuelled equipment is installed in a crawl space or an attic, the hard-wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b.
In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2.
APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall
comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certified.
3.
SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8)
feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fuelled heating appliance or equipment. The sign shall
read, in print size no less than one-half (1/2) inch in size, GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS .
4.
INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fuelled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.089(2)(a) 1 through 4.
(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.
1.
The equipment listed in Chapter 10 entitled Equipment Not Required To Be Vented in the most current edition of NFPA 54 as adopted by the
Board; and
2.
Product Approved side wall horizontal vented gas fuelled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS --- GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved
side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions
provided by the manufacturer for installation of the equipment and the venting system shall include:
1.
Detailed instructions for the installation of the venting system design or the venting system components; and
2.
A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS --- GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product
Approved side wall horizontally vented gas fuelled equipment does not provide the parts for venting the fuel gases, but identifies special venting
systems , the following requirements shall be satisfied by the manufacturer.
1.
The referenced special venting system instructions shall be included with the appliance or equipment installation instructions; and
2.
The special venting systems shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e))
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fuelled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the
installation.
2
Table of Contents
Caution
Safety
Owners Information
First Fire
Remote Control Operation
Maintenance
Lighting Instructions
Installer information
Fireplace Dimensions
Clearances to Combustibles
Locating the Fireplace
Surround Installation
Venting
Venting Components
Plumbing and Electrical
Gas Supply
Gas Pressure Check
Gas Pressure Testing Procedure
Pilot Adjustment
Propane Conversion
Door Installation / Removal
Fan Installation/ Removal
Panel Installation/Removal
Burner And Tray Installation/Removal
Log Set Installation/Removal
Glass Burner Kit Installation/Removal
Intake Air Damper Installation
Sales Codes
Wiring Diagram
Installation Notes
3
4
5
6
7
15
17
18
20
21
22
23
25
26
27
27
28
28
29
30
30
31
32
33
34
35
36
37
38
Caution
FOR YOUR SAFETY - Do not install or operate your Pacific Energy fireplace without first
reading and understanding this manual. Any installation or operational deviation from the
following instructions voids the Pacific Energy Warranty and may prove hazardous.
This appliance and its individual shut off valve must be disconnected from gas supply piping
system during any pressure testing of that system at test pressures in excess of 1/2 psi
(3.5 kPa).
This appliance must be isolated from the gas supply piping system by closing its individual
manual shut off valve during any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psi (3.5 kPa).
Do not use the fireplace if any part has been under water. Immediately call a qualified service
technician to inspect the fireplace and to replace any part of the control system and any gas
control which has been under water.
This fireplace is equipped with a micro mesh safety screen for your protection and
must be installed with the unit. Removal of the safety screen will cause the fireplace
to become a burn and fire hazard.
4
Safety

Due to high temperatures, this gas appliance should be located out of traffic and away
from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and
should stay away to avoid burns or clothing ignition.

Young children should be carefully supervised when they are in the same room as the
appliance. Toddlers, young children and others may be susceptible to accidental contact
burns.

A physical barrier is provided if there are at risk individuals in the house. To restrict access
to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children
and other at risk individuals out of the room and away from hot surfaces.

Clothing or other flammable material should not be placed on or near the appliance.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with
the appliance and shall be installed.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s
barrier for this appliance.

Any safety screen, guard, or barrier removed for servicing the appliance, must be replaced
prior to operating the appliance.

Installation and repair should be done by a qualified service person. The appliance should
be inspected before use and at least annually by a professional service person. More
frequent cleaning may be required due to excessive lint from carpeting, bedding material,
etc. It is imperative that control compartments, burners and circulating air passageways of
the appliance be kept clean.

This appliance must not be connected to a chimney flue serving a separate solid fuel
burning appliance.

It is our policy that no responsibility is assumed by the Company or by any of its
employees or representatives for any damages caused by an inoperable, inadequate, or
unsafe condition which is the result, either directly or indirectly, of any improper operation
or installation procedures.
5
OWNER’S
INFORMATION
Congratulations on your purchase of a Pacific Energy Gas Fireplace.
Your fireplace has been professionally installed by:
Dealer name: ___________________
Phone Number: _________________
If you discover any problems with your gas fireplace contact your dealer immediately to have the
unit repaired.
Caution: Do not attempt to repair the fireplace, you may cause injury to yourself or others and risk
causing damage to the unit.
Before operating your fireplace carefully read this manual and pay close attention to all Safety
Warnings. The manual contains important information on the unit’s safe operation and
maintenance.
First Fire
When lit for the first time, the fireplace will emit a slight odour for a couple of hours. This is due to
the curing of paints, sealants, gaskets, and lubricants used in the manufacturing process. This
condition is temporary. Open doors and windows to ventilate the area. Odour caused by the curing
process may cause discomfort to some individuals.
It is normal for fireplaces fabricated from steel to give off some expansion and/or contraction
noises during the start up or cool down cycle. Similar noises are found with your furnace heat
exchanger or cook stove oven.
6
Remote Control Operation
`
OWNER’S
INFORMATION
Important
The Proflame Transmitter is an integrated part of the Proflame System, which consists of:
• Proflame Transmitter, to be used in conjunction with
• Integrated Fireplaces Control (Proflame IFC)
The Proflame Transmitter provides for controlling of the following hearth appliance functions:
1. Main Burner On/Off
2. Main Burner flame modulation (6 levels)
3. Choice of standing or intermittent pilot (CPI/IPI)
4. Thermostat and Smart thermostat functions
5. Accent light modulation (6 levels)
6. Split flow valve
7. Comfort Fan speed modulation (6 levels)
Transmitter (Remote Control with LCD Display)
The Proflame Transmitter uses a streamline design with a simple button layout and informative
LCD display (Fig. 1). A Mode Key is provided to index between the features and a Thermostat Key
is used to turn on/off or index through Thermostat functions (Fig. 1 & 2). Additionally, a Key Lock
feature is provided (Fig. 21).
Figure 1: Proflame Transmitter
7
OWNER’S
INFORMATION
Technical Data
Remote Control
Supply voltage
Ambient temperature ratings
Typical operative distance in free air
Radio frequency
4.5 V (three AAA LR03 1.5 V batteries)
0 - 50 °C (32 - 122 °F)
12 m
315 MHz ( FCC version )
433.92 MHz ( CE version )
WARNING
THE TRANSMITTER AND RECEIVER ARE RADIO FREQUENCY DEVICES.
PLACING THE TRANSMITTER IN OR NEAR METAL MAY SEVERELY REDUCE THE
SIGNAL RANGE.
METALLIC STRUCTURES OR RADIO INTERFERENCES CAN REDUCE THE OPERATIVE
DISTANCE OF THE DEVICE DEPENDING ON TYPE OF FIREPLACE, INSTALLATION AND
ENVIROMENT.
ATTENTION!
- TURN “OFF” THE MAIN GAS SUPPLY OF THE APPLIANCE DURING INSTALLATION OR
MAINTENANCE OF THE RECEIVER DEVICE.
- TURN “OFF” MAIN GAS SUPPLY TO THE APPLIANCE PRIOR TO REMOVING OR
REINSERTING THE BATTERIES.
- IN CASE OF REMOTE CONTROL MALFUNCTION TURN OFF THE IFC DEVICE USING
THE “ON/OFF” MAIN SWITCH.
- FOR INSTALLATION/MAINTENANCE SWITCH OFF THE IFC DEVICE REMOVING MAIN
POWER SUPPLY PLUG.
- THE DEVICE IS NOT SUITABLE FOR THE USE OF RECHARGABLE BATTERIES AND ITS
OPERATIVE DISTANCE IS REDUCED WITH LOW BATTERY LEVEL.
8
OWNER’S
INFORMATION
Wall mounting
The Proflame remote control is supplied with an adapter for wall mounting.
Install the controller 1.5 m above floor level, well away from heat sources, kitchens, doors or
windows.
Metallic structures or radio interferences can reduce the operative distance of the device.
Make sure to attach the adapter in a level plane without any distortion. Proceed as follows:
• Detach the adapter from the body of the remote control; see Fig. A.
• Position the adapter on the wall, mark the points for the fixing holes and drill the wall.
• Fix the adapter on the wall using the mounting hardware supplied with the remote control.
• Insert the remote control onto the adapter as shown in Fig. B.
Figure A: Detach the adapter from the body
Figure B: Adapter and remote control
OPERATING PROCEDURE
Initializing the System for the first time
Power the receiver. Activate the procedure of the receiver
address programming, see the receiver instruction (*).
The Receiver will “beep” three (3) times to indicate that
it is ready to synchronize with a Transmitter. Install the
3 AAA type batteries in the Transmitter battery bay, located
on the base of the Transmitter. (fig. 3) With the batteries
already installed in the Transmitter, push the On button.
The Receiver will “beep” four times to indicate the
Transmitter’s
command is accepted and sets to the particular code
of that Transmitter. The system is now initialized.
(*) The receiver may be independent or integrated to the IFC hearth
appliance control module. The receiver instruction may not be
independent when part of the IFC.
Figure 3: Battery
compartment
9
OWNER’S
INFORMATION
Temperature indication Display
With the system in the “OFF” position, press the Thermostat Key and the
Mode Key at the same time. Look at the LCD screen on the transmitter to
verify that a C or F is visible to the right of the Room Temperature display.
(Fig. 4 & 5)
Figure 4: Display in Fahrenheit
Turn on the Appliance
With the system OFF, press the ON/OFF Key on the
Transmitter. The Transmitter display will show some other
active Icons on the screen. At the same time the Receiver
will activate the appliance. A single “beep” from the
Receiver will confirm reception of the command.
Figure 5: Display in Celsius
Turn off the Appliance
With the system ON, press the ON/OFF Key on the
Transmitter. The Transmitter LCD display will only show
the room temperature (Fig. 6). At the same time the
Receiver will turn off the appliance. A single “beep” from
the Receiver confirms reception of the command.
Figure 6: Remote Control
Display
Remote Flame Control
The Proflame has six (6) flame levels. With the
system on, and the flame level at the maximum in
the appliance, pressing the down arrow key once
will reduce the flame height by one step until the
flame is turned off.
The Up Arrow Key will increase the flame height
each time it is pressed. If the Up Arrow Key is
pressed while the system is on but the flame is off,
the flame will come on in the high position. (Fig. 7)
A single “beep” will confirm reception of the
command.
Figure 7:
10
OWNER’S
INFORMATION
ROOM THERMOSTAT (Transmitter Operation)
The Remote Control can operate as a room thermostat. The
thermostat can be set to a desired temperature to control the
comfort level in a room.
To activate this function, press the Thermostat key (Fig. 1). The
LCD display on the transmitter will change to show that the room
thermostat is “ON” and the set temperature is now displayed
(Fig.8). To adjust the set point, press the up or down arrow keys
until the desired set point temperature is displayed on the LCD
screen of the transmitter.
Figure 8
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the flame height in
accordance to the difference between the set point and the room
temperatures. As the room temperature gets closer to the set point
the Smart Function will modulate the flame down. If the room
temperature is cool the Smart function will modulate the flame up.
To activate this function, press the THERMOSTAT key (Fig. 1)
until the word "SMART" appears to the right of the temperature
bulb graphic (Fig. 9). To adjust the set point, press the up or down
arrow keys until the desired set point temperature is displayed on
the LCD screen of the transmitter (Fig. 10).
Note. When Smart Thermostat is activated, manual flame height
adjustment is disabled
Figure 9: Smart Flame
Function
Figure 10
Fan Speed Control
If the appliance is equipped with a hot air circulating fan, the speed of the fan can be
controlled by the Proflame system. The fan speed can be adjusted through six (6) speeds.
To activate this function use the Mode Key (Fig.1) to index to the fan control icon (Fig. 11).
Use the Up/Down Arrow Keys (Fig.1) to turn on, off or adjust the fan speed (Fig. 12). A
single “beep” will confirm reception of the command.
Figure 11
Figure 12
11
OWNER’S
INFORMATION
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
With the system in "OFF" position press the Mode Key (Fig. 1) to index to the CPI mode
icon (fig. 13 & 14).
Pressing the Up Arrow Key will activate the Continous Pilot Ignition mode (CPI). Pressing
the Down Arrow Key will return to IPI. A single “beep” will confirm the reception of the
command.
NOTE: this function is available only with Proflame IFC.
NOTE: If the system is equipped with a CPI/IPI toggle switch:
• Set the CPI/IPI switch to CPI position(switch closed) to enable remote CPI/IPI
operation.
• Set the CPI/IPI switch to IPI position (switch open) to disable remote CPI/IPI
operation. The system will now work in IPI mode only regardless of the selection on
the remote control hand set.
Figure 13
Figure 14
Remote dimmer control (Light)
The dimmer function controls the Light power outlet by power light control. To activate this
function use the Mode Key (Fig. 1) to index to the Light icon (Fig. 15 & 16).
The intensity of the output can be adjusted through six (6) levels. Use the Up/Down Arrow Keys
(Fig.1) adjust the output level. A single “beep” will confirm reception of the command.
Note. This function is available only with the Proflame IFC.
Figure 15
Figure 16
12
OWNER’S
INFORMATION
KEY LOCK
This function will lock the keys to avoid unsupervised operation.
To activate this function, press the MODE and UP Keys at
the same time (Fig. 21).
To de-activate this function, press the MODE and UP Keys
at the same time.
Figure 21
LOW BATTERY POWER DETECTION
Transmitter
The life span of the remote control batteries depends on
various factors: quality of the batteries used, the number
of ignitions of the appliance, the number of changes to
the room thermostat set point, etc.
When the Transmitter batteries are low, a Battery Icon
will appear on the LCD display of the Transmitter (Fig. 22)
before all battery power is lost. When the batteries are
replaced this Icon will disappear.
Figure 22
WARNING
Fire Hazard. Can cause severe injury or death
The Receiver causes ignition of the appliance. The appliance can turn on suddenly. Keep
away from the appliance burner when operating the remote system or activating manual
bypass of the remote system.
13
OWNER’S
INFORMATION
DIMENSIONAL DRAWINGS
Fig. 23: PROFLAME
Transmitter dimensional drawing
14
Maintenance
OWNER’S
INFORMATION
Turn off gas and electrical power supply (if applicable) and allow ample time for unit to cool
before servicing appliance. It is recommended that the fireplace and its venting should be
inspected at least once a year by a qualified service person.
Glass Door:
Warning: Do not operate fireplace with glass door removed, cracked or broken. Replacement of
the glass door should be done by a licensed or qualified service person.
Do not strike or otherwise impact the glass in any way that may cause it to break. If the glass
becomes cracked or broken it must be replaced before using the fireplace. Replacement door can be
obtained from your nearest Pacific Energy dealer. Do not substitute with any other type.
Only the door certified with the appliance shall be used
To remove broken glass, remove Door as noted in "Door Removal" section.
Annual Inspection:
The following procedures must be performed each year by certified personnel.
a) Remove glass door and decorative media (such as logs and rocks). Inspect decorative media
and burner assemblies for soot buildup. If excessive buildup of soot is present, have a
qualified service person inspect and adjust unit for proper combustion. Clean burners with a
brush or vacuum cleaner, paying close attention to burner ports.
b)
Check the pilot system for proper flame size and operation. Pilot light flame must be long
enough to overlap the burner ports. Clean pilot hood and spark rod free of soot, dust or any
other deposits.
.
15
OWNER’S
INFORMATION
c) Check that the vent pipe and vent terminal are open and free from blockage or debris. The flow
of combustion and ventilation air must not be obstructed. If the venting is disassembled for
cleaning, it must be properly assembled and re-sealed.
d) Check glass panel gasket, replace if necessary. It is important that the glass seal be maintained
in good condition.
e) Check and replace batteries as needed.
Note: The appliance area must be kept clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
Periodically:
a) Viewing glass may be cleaned as necessary with fireplace glass cleaner.
b) Exterior finish may be cleaned with mild soap and water.
CAUTION:
Do not use abrasive cleaners on glass or any other part of the fireplace.
Do not clean glass when hot
16
Lighting Instructions
17
OWNER’S
INFORMATION
INSTALLER
INFORMATION
Fireplace Dimensions
The installation must conform with local codes or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the National Gas and Propane
Installation Code, CSA B149.1
A manufactured home (USA only) or mobile home OEM installation must conform with
the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or,
when such a standard is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or standard for Gas Equipped Recreational Vehicles
and Mobile Housing , CSA Z240.4
Fig. 25: Framing
Fig. 24: Fireplace Dimensions
18
INSTALLER
INFORMATION
Fig. 26: Framing At The Corner
Fig. 27: Minimum Clearance
Corner Framing
19
INSTALLER
INFORMATION
Clearances to Combustibles
LEFT SIDE
RIGHT SIDE
FRONT
Front of the appliance is an open side of the combustion chamber
covered with the glass.
Facing the front of the appliance side from left is the left side of the
appliance and side from right is the right side of the appliance.
Figure 28: Minimum Distance
From Top Of The Glass To Ceiling
Figure 29: Front and Side Definitions
Minimum Clearance to Combustible Materials
ENCLOSED SIDE WALL
ENCLOSED BACK WALL
ENCLOSED CEILING
ECLOSED FRONT WALL
EXPOSED SIDE WALL
VENT ENCLOSURE
EXTERIOR SOFIT
1.75"
NCR*
4"
24" From top of the glass
8" From side of the glass
1"
16"
*NCR STANDS FOR NO CLEARANCE REQUIRED; YOU MAY USE COMBUSTIBLE CONSTRUCTION
MATERIALS IN DIRECT CONTACT WITH THE APPLIANCE ON THESE SURFACES.
When the appliance is installed directly on carpeting, tile or other combustible material other
than wood flooring, the appliance shall be installed on a metal or wood panel extending the full
width and depth of the appliance. Specified clearances shall be maintained from the top surface
of carpeting, tile, etc.
20
Locating the Fireplace
INSTALLER
INFORMATION
In planning the installation for the fireplace, it is necessary to determine where the unit is to be
installed, location of vent system and where gas supply piping may be plumbed. Various
installations are possible, such as, into an existing wall, a corner, a built in wall or a wall projection.
Due to high temperatures, do not locate this fireplace in areas of high traffic or near furniture or
draperies. For places where a second side wall is specified, fireplace should be accessible for
service
Figure 30: Common Installation Location
Figure 31: Framing Dimensions
21
INSTALLER
INFORMATION
Surround Installation Instructions
Figure 33: Clean Face Surround
Figure 32: Louvered Surround
Installation
1. Fasten the surround base to the fireplace using supplied screws and mounting holes located along
the inner edge of the base.
2. Install screen with the frame in slots on inner side of the surround base.
3. Install the surround front by positioning it so as to clear the notches and secure by applying
downward pressure in order to engage the locking tabs.
Figure 34: Surround Dimensions
22
Venting
INSTALLER
INFORMATION
Note: The intake
damper positions
specified in this
chart were set in a
controlled testing
environment, and
serve as a general
guideline for
installations. Every
venting configuration
is different, and the
damper setting may
need slight
adjustment from this
chart.
Note: The vent must
not exceed a total
length of 35 feet.
Any combination of
rise and run may be
used but must be
constrained to the
boundaries of this
chart. A Maximum of
three 90° elbows
may be used. Only
one (1) 90° elbow or
combination of other
elbows equalling 90°
can be used without
reducing horizontal
run. For each
additional 90° elbow,
or an equal
combination of
elbows, reduce
horizontal vent run
by 2 feet. Ensure
vent pipe is properly
supported.
23
INSTALLER
INFORMATION
This fireplace is certified for use with 4” x 6-5/8”coaxial venting components only. It is permitted to only use
certified venting for this appliance.
24
Venting Components
NOTE: Mixing venting components from different manufacturers is inadvisable.
Figure 35: 4”x6-5/8" Rigid Piping Cross Reference Chart
Figure 1: 4”x6-5/8" Rigid Piping Cross Reference Chart
Figure 36: 4”x6-5/8" Rigid Pipe Components Cross Reference Chart
25
INSTALLER
INFORMATION
INSTALLER
INFORMATION
Plumbing and Electrical
Gas connection
To make the required electrical and
gas connections, start by positioning
the gas fireplace. Connect the gas
supply line to the 1/2” fitting that
located on a shut off valve bracket as
seen in Figure 37. A gas shut off valve
is located inside the fireplace and may
be accessed by removing the inner
firebox unit.
Please see the gas supply section for
requirements of the gas supply.
Figure 37: Gas Connection
Figure 37A: Electrical Connection
Electrical connection
Open the access panel as seen in Figure 37A and connect the line wires to the supplied
wires inside the junction box using marrettes. A licensed electrician must be used to make
this connection.
26
INSTALLER
INFORMATION
Gas Supply
Servicing of the appliance can be performed from the front of the unit by removing the door and the burner tray from
the unit.
Caution: The gas line should be installed by a qualified service person in accordance with all building codes. This
section is intended as a guide for qualified technicians installing this appliance. Consult local and/or national building
codes before proceeding.

Gas supply line connection is located on the side of the fireplace. Gas connection accepts a ½” NPT fitting.
Correct gas line diameter must be used to assure proper operation and pressure.

The fireplace input rating is shown in the chart below.

A drip leg must be installed in the gas supply line going to the gas control valve to minimize the possibility of
any loose scale or dirt within the gas supply line from entering the control valve.
Check local codes for additional requirements.
Turn on the gas supply and check that all connections are tight and leak free.
WARNING: The gas tray including gasket must be reinstalled after conversion/installation or servicing has
been completed.
Gas Pressure Check
Please refer to following page for gas pressure testing procedure.
Esprit
Gas pressure
requirements
Gas Orifice
NG 2.55mm
Input Pressure
Natural GasPropane
Minimum
Maximum
4.5" WC
13.9" WC
11.0" WC
13.9" WC
3.5" WC
1.6" WC
10" WC
6.4" WC
LP
Manifold Pressure
High
Low
27
1.52mm
Output
AFUE
30,000 btu/hr max. 75%
22,000 btu/hr min.
26,000 btu/hr max. 76%
22,000 btu/hr min.
INSTALLER
INFORMATION
Gas Pressure Testing Procedure
Note: To test the gas pressure, turn off the gas supply to the appliance before loosening
test point screws.
Verify gas pressures with the fireplace lit and at the highest setting.
1. Remove window surround and locate the valve as seen in Figure 38.
2. Locate the inlet and outlet test ports on the valve which can be seen in Figure 39. After
locating test ports loosen the screws within the ports using a flat-tip screwdriver.
3. Attach pressure gauge to the test ports
4. Turn gas supply back on and test pressures.
5. After testing is finished turn off gas supply, remove the pressure gauges and tighten up the
screws in the test points.
VENTURI ADJUSTMENT SCREW
Pilot Adjustment
The pilot flame level can be adjusted by
turning the adjustment screw, using a flattip screwdriver, seen on the valve in
Figure 39.
Figure 24: Valve Location
Figure 38: Valve
Figure 39: Valve
28
Propane Conversion
INSTALLER
INFORMATION
Before starting the conversion make sure to shut off
the gas supply to the unit and allow fireplace to cool to
room temperature.
To convert the gas fireplace from natural gas to propane
the kit is required. This kit comes with new pilot and
burner orifices as well as a new pressure modulator for the
valve.
To switch the pressure modulator, follow the instructions
that are provided with the conversion kit.
To change the orifices you are required to remove the
door, media set, and burner. Please refer to the
appropriate sections of this manual and follow instructions
on how to correctly remove the components.
Figure 40: Burner Orifice and Pilot
After removing the burner you will have access to the
burner orifice which is located on the bottom of the burner
tray, as seen in Figure 40. The orifice can be removed
using a ½” socket. Before installing the new orifice, Thread
Sealant needs to be applied to the threads of the new
orifice to ensure a proper seal when installed.
To replace the pilot orifice you will need to remove the pilot
hood which is held in place by a spring. First remove the
spring, and then remove the hood by pulling it up from the
pilot bracket, seen in Figure 41. To remove the existing
orifice insert a 5/32” or 4mm Allen wrench into the
hexagonal key-way of the orifice and rotate counterclockwise until free. Insert the new orifice using the same
Allen wrench and tighten it until a torque of 9 lbf in (1 Nm)
is achieved. Replace the pilot hood by aligning the tab on
the base of the hood with the slot in the side of the pilot
journal, and push the hood down onto the pilot bracket.
Replace the spring by pushing it onto its seat.
Figure 41: Pilot
Before returning the burner into position, the venturi
shutter will have to be adjusted to the correct opening. The
correct venturi settings are shown in Figure 42. Loosen the
screw and slide the shutter. Tighten the screw, and return
the burner into position.
Figure 42: Venturi Shutter
29
INSTALLER
INFORMATION
Door Installation/Removal
Installation
1. Place the door in the slot at the
bottom of the firebox opening.
2. Hold the door against the firebox.
Push 3 levers at the top of the
door to secure the door.
Removal
1. Hold the door. Pull 3 levers to
release the door.
2. Lift the door up to release it from
the slot on the bottom of the
firebox.
Figure 43: Door
Fan Installation / Removal
Fan removal after fireplace
installation.
1. Remove door surround and
glass frame with the glass
as seen in Figure 44.
2. Turn off main gas supply to
unit and disconnect 3/8" flex
tubing from inner firebox.
Also disconnect power cord
from inner firebox.
3. Remove rock tray and
burner.
4. Remove baffle, rear panel
and side panels.
5. Remove burner tray
together with valve
assembly.
6. Disconnect fan electrical
wires and remove fan
fasteners.
7. Remove fan out of the
firebox assembly.
Figure 44: Fan Installation/Removal
30
INSTALLER
INFORMATION
Fan removal before fireplace installation.
1. Remove fan panel at the rear side of the fireplace as seen in Figure 44.
2. Disconnect fan electrical wires and remove fan fasteners.
3. Remove fan out of the firebox assembly.
Panel Installation / Removal
Installation/Removal
1. Insert back panel so that it is sitting on ledge at
the back of the firebox as shown in Figure 46.
2. Insert first side panel by inserting the front
edge of the panel into the lip at the front of the
firebox. Then slide the back of the panel until it
reaches the firebox side wall. See Figure 47.
3. Repeat steps 2 for the second side panel.
4. To hold panels in place, install the baffle, from
the burner kit, by resting the back flange on top
of the back panel and use two screws to
secure the front of the baffle to the top of the
firebox, seen in Figure 48.
5. Do panel removal in reverse order.
Figure 45: Panel Set
Figure 46: Back Panel
Figure 47: Side Panel
Figure 48: Baffle Mounts
31
INSTALLER
INFORMATION
Burner and Tray Installation / Removal
Burner Tray Installation /
Removal
Installation
Place the burner tray in the fireplace.
Turn off main gas supply to unit and
connect 3/8" flex tubing and power cord
from inner firebox . Secure tray with
screws placed around the perimeter of
the tray using a screwdriver, as seen in
Figure 49.
Figure 49: Burner Tray
Removal
Remove the screws seen in Figure 49
using a screwdriver. Turn off main gas
supply to unit and disconnect 3/8" flex
tubing from inner firebox. Also disconnect
power cord from inner firebox and
remove the burner tray.
Burner Installation / Removal
Installation
Place the burner in firebox so that the
venturi is over top of the orifice. To
secure the burner, insert the screws as
seen in Figure 50 using a screwdriver .
Removal
Remove the screws as seen in Figure 50
and lift the burner out of the unit.
Figure 50: Burner
Embers Placement
Place embers chunks in rock tray as seen
in Figure 51. Do not block air openings
and pilot elements with embers.
Figure 51: Ember Placement
32
INSTALLER
INFORMATION
Log Set Installation / Removal
Place the Logs #1 and #2 as seen in Fig.53
than place Log #3 over dowel pin on Log #2 as
seen in Fig.54.
Place Log #6 to the left side seen in Fig 55.
Place side Log #5 and #4 as seen in Fig 56.
Place Log #7 as seen in Fig.57
Complete Log Set should look like it is shown in
Fig 58. Logs should not touch the flame and
overlap pilot or air openings in rock tray.
Figure 52: Log Set
Figure 53: Two Rear Logs
Figure 54: Rear Log Set
Figure 55: Left Side Log
Figure 56: Front Logs
Figure 58: Complete Setup
Figure 57: Middle Log
33
INSTALLER
INFORMATION
Glass Burner Kit Installation / Removal
Glass Installation
To install the glass, evenly spread a thin layer of crushed glass across the entire burner pan as
seen in Figure 67.
))
To install the optional rock set, simply place desired number of rocks into the fireplace pan as seen
in Figure 68 making sure no rocks are in the flame when the unit is operating.
Figure 67: Glass Installation
Figure 68: Rocks Installation
34
Intake Air Damper Installation
INSTALLER
INFORMATION
The Esprit fireplaces come with the damper that can limit the flow of intake air. This damper is
located behind the air baffle at the top of the inner firebox. Sometimes on installations that involve
vertical venting configurations over 23 feet in height, the intake air tends to accelerate down the
vent causing hectic flame action. This damper can be closed to reduce the speed of the intake air
and thus calm the flames to a more natural look. See Page 23 to check if damper required for
installation.
35
INSTALLER
INFORMATION
ESPRIT LINEAR GAS FIREPLACE SALES CODES
UNIT
ESPRIT LINEAR GAS FIREPLACE ......................................
ESPR.BODYA
REPLACEMENT PARTS
ESPRIT REPLACEMENT DOOR WITH GLASS ...................
ESPRIT REPLACEMENT SCREEN ......................................
PROPANE CONVERSION KIT ..............................................
COMPLETE REPLACEMENT GAS TRAY ............................
REPLACEMENT GAS VALVE ...............................................
REPLACEMENT CONTROL MODULE .................................
REPLACEMENT PILOT ASSEMBLY ....................................
REPLACEMENT REMOTE CONTROL .................................
REPLACEMENT BLOWER ...................................................
ESPR.DOORA
ESPR.SCRNA
GASC.LPKIT
ESPR.BRNTRAYA
GASC.VALVEA
GASC.MODA
GASC.PILOTA
GASC.CNTRLB
GASC.SBLOWA
BURNER OPTIONS
LOG BURNER SET ...............................................................
GLASS BURNER SET ...........................................................
GLASS 5LB BLACK ...............................................................
GLASS 5LB TWILIGHT .........................................................
GLASS 5LB DESERT ............................................................
GLASS 5LB PACIFIC ............................................................
ESPR.NG01A
ESPR.NG03A
GASC.5GLBK
GASC.5GLTW
GASC.5GLDE
GASC.5GLPA
PANEL SETS
PORCELAIN PANEL SET BLACK .........................................
PORCELAIN PANEL SET TITANIUM ...................................
PORCELAIN PANEL SET COFFEE BEAN ...........................
PORCELAIN PANEL SET COPPER .....................................
PORCELAIN PANEL SET RED .............................................
PORCELAIN PANEL SET IVORY .........................................
ESPR.PNPBKA
ESPR.PNPTIA
ESPR.PNPCBA
ESPR.PNPCUA
ESPR.PNPRDA
ESPR.PNPIYA
SURROUND AND TRIM OPTIONS
CONTEMPORARY BACKING PLATE BLACK.......................
CONTEMPORARY BACKING PLATE GREY........................
CONTEMPORARY FRONT TRIM PLATE..............................
CONTEMPORARY FRONT TRIM PLATE - BLACK ..............
CONTEMPORARY FRONT TRIM PLATE - STAINLESS ......
LOUVERED SURROUND BLACK .........................................
LOUVERED SURROUND GREY...........................................
ESPR.CSURRA
ESPR.CSURRGYA
ESPR.CSTGYA
ESPR.CSTBKA
ESPR.CSTSSA
ESPR.LVSBKA
ESPR.LVSGYA
DESIGN OPTIONS
TRANQUILITY ROCK SET ....................................................
METRO ROCK SET - BLACK ................................................
METRO ROCK SET - GREY .................................................
GASC.TRANQA
GASC.METROBKA
GASC.METROGYA
PERFORMANCE OPTIONS
OPTIONAL BLOWER KIT ......................................................
LP CONVERSION KIT ...........................................................
36
ESPR.BLOWKITA
GASC.LPKIT
Wiring Diagram
INSTALLER
INFORMATION
Caution: Label all wires
prior to disconnection
when servicing controls.
Wiring errors can cause
improper and dangerous
operation.
Verify proper operation
after servicing.
37
INSTALLER
INFORMATION
Installation Notes
NOTES:
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
38
INSTALLER
INFORMATION
39
Technical support: 1-250-748-1184
Web site: www. pacificenergy.net
2975 Allenby Rd., Duncan, BC V9l 6V8