Runco CL-610LT Specifications

O W N E R ’S O P E R A T I N G M A N U A L
CL-610 and CL-610LT
DLP™ Projectors
Table of Contents
Limited Warranty ............................................................................ 5
Safety Precautions ......................................................................... 8
Overview ......................................................................................... 9
Features .............................................................................................................. 9
Front / Top View ................................................................................................... 10
Rear / Bottom View .............................................................................................. 11
Controls and Functions .................................................................. 13
Control Panel ....................................................................................................... 13
Connector Panel .................................................................................................. 14
Runco Logo ......................................................................................................... 14
Remote Control .................................................................................................... 15
Installation ...................................................................................... 17
Remote Control .................................................................................................... 17
Installation Considerations .................................................................................... 18
Connections .................................................................................... 23
Connecting Video Inputs ...................................................................................... 23
Connecting a Computer (GBRHV) ......................................................................... 25
Connecting an HDMI™ Device .............................................................................. 25
Connecting to AC Power ...................................................................................... 26
Basic Operation .............................................................................. 27
Turning on the Power ........................................................................................... 27
Adjusting the Zoom and Focus ............................................................................. 27
Adjusting Projector Height or Projection Angle ....................................................... 27
Selecting Video Memory ....................................................................................... 28
Selecting an Aspect Ratio ..................................................................................... 28
Adjusting the Picture ............................................................................................ 28
Setting the Menu .................................................................................................. 29
Selecting the Input Source .................................................................................... 29
PIP / PBP Function .............................................................................................. 29
Turning off the Power ........................................................................................... 30
On-Screen Display Menus .............................................................. 31
Using the Menu .................................................................................................... 31
Main Menu ........................................................................................................... 31
Picture Quality Adjustments .................................................................................. 32
Aspect Ratio ........................................................................................................ 34
Installation ........................................................................................................... 35
Option ................................................................................................................. 37
Setup .................................................................................................................. 39
Runco CL-610 Owner’s Operating Manual
3
Table of Contents (continued)
ISF Calibration ..................................................................................................... 43
Lamp Replacement ........................................................................ 45
Troubleshooting .............................................................................. 47
RS-232 Setup .................................................................................. 49
Connecting RS-232 to the Projector ..................................................................... 49
RS-232C Control Codes ....................................................................................... 50
Specifications ................................................................................. 53
Dimensions ..................................................................................... 55
4
Runco CL-610 Owner’s Operating Manual
TWO YEAR LIMITED WARRANTY
For Projectors, Video Processors and Controllers
Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe
Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup and care, you
should enjoy many years of unparalleled video performance.
This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and
retain it with your other important documents.
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
SERVICE LABOR: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result
of manufacturing defect for a period of two (2) years from the effective date of delivery to the end user (excluding
the lamp).
PARTS: (Not including the lamp) Runco will provide new or rebuilt replacement parts for the parts that fail due to
defects in materials or workmanship for a period of two (2) years from the effective date of delivery to the end user.
Such replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty
period.
PROJECTOR LAMP: Runco will pay for service labor by a Runco Authorized Service Center when needed as
a result of a manufacturing defect for a period of six (6) months or 1000 hours, which ever comes first, from
the effective date of delivery to the end user. In addition, Runco will provide a new or rebuilt replacement lamp
for the lamp that fails due to defects in materials or workmanship for a period of six (6) months or 1000 hours,
which ever comes first, from the effective date of delivery to the end user. Such replacement lamps are then
subsequently warranted for the remaining portion (if any) of the original warranty period.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use
and does not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items;
failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation
or setup adjustments; improper maintenance, alteration, improper use of any input signal; damage due to lightning
or power line surges, spikes and brownouts; damage that occurs during shipping or transit; or damage that is
attributed to acts of God. In the case of remote control units, damage resulting from leaking, old, damaged or
improper batteries is also excluded from coverage under this Limited Warranty.
CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO
AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE
UNDER THIS LIMITED WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM
IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED
WARRANTY.
Runco CL-610 Owner’s Operating Manual
5
RIGHTS, LIMITS AND EXCLUSIONS:
Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty
period. There are no express warranties. Runco also excludes any obligation on its part for incidental or consequential
damages related to the failure of this product to function properly. Some states do not allow limitations on how long
an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential
damages. So the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights that vary from state to state.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of
sale as evidence of the purchase date.
IMPORTANT: WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly
if we should discover a safety problem or product update for which you must be notified.
CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:
Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at
the location of the product, during usual working hours, providing location of product is within normal operating
distance from a Runco Authorized Service Center. In some instances it may be necessary for the product to be
returned to the Runco factory for repairs. If, solely in Runco’s judgment, location of product to be repaired is
beyond normal operating distance of the closest Runco Authorized Service Center, or the repair requires the unit
be returned to the Runco factory, it is the owner’s responsibility to arrange for shipment of the product for repair.
These arrangements must be made through the selling Runco Dealer. If this is not possible, contact Runco directly
for a Return Authorization number and shipping instructions. Runco will return product transportation prepaid in
the United States, unless no product defect is discovered. In that instance, shipping costs will be the responsibility
of the owner.
COPYRIGHT AND TRADEMARKS
© Copyright 2005 Runco International. This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other
means, in any form, without prior written permission of the manufacturer.
All trademarks and registered trademarks are the property of their respective owners.
6
Runco CL-610 Owner’s Operating Manual
ADDITIONAL INFORMATION:
To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about
this Limited Warranty, please call or write:
RUNCO INTERNATIONAL, INC.
Attn: Customer Service Department
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-7777
Fax: (510) 324-9300
Toll Free: (800) 23-RUNCO
RUNCO VIDEO PRODUCT INFORMATION
RETAIN THIS INFORMATION FOR YOUR RECORDS
Model Purchased
Date
Serial Number
Runco Authorized Dealer Name
Address
City
State/Province
Phone
Fax
Runco CL-610 Owner’s Operating Manual
7
Postal Code
Safety Precautions
Thank you for your purchase of this quality Runco video projector! It has been designed
to provide you with the quality of video that is expected in a home theater. For the
best performance, please read this manual carefully as it is your guide through the
menus and operation.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING
This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this projector near water, outdoors or otherwise exposed to the
elements.
5. Clean only with a dry cloth.
6. Do not block any ventilation openings.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
8. Do not defeat the safety feature of the polarized or grounding type plug. A polarized
type plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The third prong is provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for
the replacement of the obsolete outlet.
9. Do not connect the RJ-11 RS-232 jack to a telephone line connection.
10. The 12V trigger only outputs DC 12V signal for triggering. Do not connect to any
other power input or output. This could cause damage to this unit.
11. Only use accessories specified by RUNCO International.
12. Keep the packing material in case the projector should ever need to be shipped.
13. Unplug this projector during lightning storms or when it will not be used for an
extended period of time.
14. The lamp becomes extremely hot during operation. Allow the projector to cool down
for approximately 45 minutes prior to removing the lamp assembly for replacement.
Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond rated life could cause them to explode in rare occasions.
15. Refer all servicing to qualified service personnel. Servicing is required when the
projector has been damaged in any way, objects have fallen or spilled into the
projector, the projector has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Runco CL-610 Owner’s Operating Manual
8
Overview
•
Native 16:9 Aspect Ratio, SuperOnyxTM DMD 1280 x 720p
•
High Contrast and Picture Quality
12-degree mirrors with dark metal process.
•
High Dynamic Range and Rich Gray-scale
6-segment, 5x color wheel with wide color space.
•
TIR (Total Internal Reflection) Prism
High-performance light engine with Cat’s Eye optics.
•
Wide Variety of Inputs
Support for various video formats, including Composite, S-Video, Component,
DTV Y/PB/PR, DTV RGB HD and Computer signals. The HDTV input (DTV Y/P B/PR
and DTV RGB) is via RGB BNC connectors, providing the least amount of signal
degradation caused by longer cable runs.
•
HDTV Ready
480p, 1080i and 720p (576p PAL Version) formats are all compatible with this unit
(via an external DTV decoder, not provided).
•
De-interlacing with 3:2 Pull-down
Using Runco’s proprietary De-interlacing technology, this projector provides
exceptional scaling and film-to-video (3:2 pulldown) conversion for the most artifactfree images possible.
•
PIP/ PBP function
Picture in Picture/Picture by Picture functions allow you to display two inputs
on the screen at the same time.
•
ISF Calibration
This product includes ISF day and night mode settings as established by the
Imaging Science Foundation. These standards provide for superior image quality
and assure the user that restoration to preset values for both day and night viewing
is accomplished by just the press of a button, should the projector’s settings or
calibrations be inadvertently disturbed.
Runco CL-610 Owner’s Operating Manual
9
Features
Overview
Front / Top View
1. Exhaust Vent
4. Top IR Sensor
2. Focus Ring and Zoom Ring
Access
Adjust the focus and zoom of image.
5. Status LEDs
See “Control Panel” on page 13.
6. Intake Vent
3. Runco Logo
Can be rotated to match floor or
ceiling installation. See “Runco
Logo” on page 14.
10
7. Front IR Sensor
8. Projection Lens
Runco CL-610 Owner’s Operating Manual
Overview
Rear / Bottom View
1. Connector Panel
See “Connector Panel” on page 14.
2. AC Power IN Socket
3. AC Power Switch
4. Cable Access Door
Open to access connectors.
See “Connector Panel” on page 14.
5. Cable Opening
Pass cables through this opening.
6. Runco Logo
Can be rotated to match floor or
ceiling installation.
See “Runco Logo” on page 14.
7. Lamp Module Cover
Remove this cover when replacing
the lamp. See “Lamp Replacement”
on page 45.
8. Front / Rear Adjusters
Adjusts the height or projection
angle.
9. Ceiling Mount Holes
The connecting holes for the ceiling
mount bracket.
Runco CL-610 Owner’s Operating Manual
11
Overview
This page is intentionally left blank.
12
Runco CL-610 Owner’s Operating Manual
Controls and Functions
Control Panel
1. FOCUS RING
Adjust the focus of the image
- Rotate the focus ring right or left to
focus the image.
2. ZOOM RING
Adjust the size of the image
- Rotate right to enlarge the image.
- Rotate left to reduce the image.
- Green when the power is turned
on (operational mode).
- Flashing Orange for the first 45
seconds after power-up indicating
that the lamp is warming up.
- Flashing Green for 110 seconds
after the projector was powered off
indicating that the lamp is cooling
down.
3. LAMP LED
Indicates the status of the lamp
- Red when the lamp has exceeded
its usage life or developed a
problem. Please contact your Runco
Dealer for assistance.
- Flashing Red when the fans are
not working or the lamp cover is
open. Please contact your Runco
Dealer for assistance.
5. TEMP LED
Indicates the status of the fans and
internal temperature
- Red when the internal temperature
is too high. Please contact your
Runco Dealer for assistance.
- Flashing Red when the fans are
not working or the lamp cover is
open. Please contact your Runco
Dealer for assistance.
4. POWER LED
Indicates the status of the power
- Orange when the AC power cord
is plugged into a wall outlet (standby
mode). Once in standby mode, you
can turn on the projector by
pressing the ON button on the
remote control.
6. TOP IR SENSOR
Runco CL-610 Owner’s Operating Manual
13
Controls and Functions
To access the connector panel, pull firmly
on the cable access cover to open it.
Connector Panel
1. S-Video (mini DIN 4-pin) Y/C (S-video) signal input
2. 12v Trigger (mini jack, diameter 5.5 mm outside, 2.5 mm inside)
+12V output, active when the projector is turned on
3. Video (RCA Jack)
Composite video signal input
4. Component (RCA Jacks)
480i Component (Y/CB/CR) video signal input
5. HDMI (High-Definition Multimedia Interface) Input
Digital video signal input
6. RGB/ HDTV (BNC) or Progressive Scan DVD players
DTV Y/PB/PR or DTV RGB video signal input
7. RS-232C (RJ-11 Jack)
RS-232C control signal input (refer to page 49 for details)
The Runco logos on the front and rear of the projector
can be rotated to match a floor or ceiling installation.
To rotate the logo, grip it at the sides, pull it away
from the projector and rotate it 180 degrees.
Runco Logo
14
Runco CL-610 Owner’s Operating Manual
Controls and Functions
LIGHT
Press to turn on the remote
control back light.
ON
Press to turn on the
projector.
OFF
Press to turn off the
projector.
LIGHT
VID
ON
VID (Video)
Composite video signal
input.
OFF
S-VID
COMP1
RGBHD
HDMI
INFO
COMP2
S-VID (S-Video)
S-Video signal input.
COMP1 (Component 1)
Component Y/CB/CR input.
RVR
COMP2 (Component 2)
DTV Y/PB/PR signal input.
ENTER
INFO
Displays active source and
aspect ratio information.
Arrow (▲,◄,▼,►)
Use to select the menu or to
make various adjustments.
ENTER
Enter the setting of items in
the menu.
RVR
Not applicable to this model.
EXIT
Exit and save the setting(s) of
items in the menu.
MENU
Turns on/off the on-screen
display menu.
EXIT
RGBHD
DTV RGBHV signal input.
MENU
HDMI
High-Definition Multimedia
Input.
BRT
CONT
COL
TNT
MEM1
ISF
NIGHT
ISF
DAY
FACT
ANA
16X9
4X3
LBOX
VWIDE
BRT (Brightness)
Adjust picture brightness.
CINEMA
1
2
VCINE
CONT (Contrast)
Adjust picture contrast.
3
4
5
6
7
8
9
0
PBP
ACT
PIP
PIP+
FOCUS
ZOOM
LENS
PIP-
Runco CL-610 Owner’s Operating Manual
COL (Color)
Adjust color intensity.
TNT (Tint)
Adjust color tones.
15
Remote Control
Controls and Functions
CINEMA
Image in Letterbox mode is
enlarged to a 16x9 image
and the upper and lower
portions are compressed.
Remote Control
(continued)
ANA (Anamorphic)
For 16:9 DVDs.
LIGHT
VID
ON
OFF
S-VID
COMP1
RGBHD
HDMI
INFO
COMP2
RVR
ENTER
EXIT
MEM1, ISF NIGHT, ISF
DAY, FACT
Recall video memory
sequentially. See “Selecting
Video Memory” on page 28.
0-9
Press to type in menu
passcodes.
MENU
BRT
CONT
COL
TNT
MEM1
ISF
NIGHT
ISF
DAY
FACT
ANA
16X9
4X3
LBOX
VWIDE
CINEMA
1
2
VCINE
3
4
5
6
7
8
9
0
PBP
ACT
PIP
PIP+
FOCUS
ZOOM
LENS
PIP-
4X3 (Standard 4:3)
The input signal will be
scaled to fit 4:3 display mode
in the center of the screen.
LBOX (Letterbox)
Image in letterbox format is
enlarged to fit 16:9 full screen
display and the upper/ lower
portions are “blanked off.”
VWIDE (VirtualWide)
4:3 image is enlarged NONlinearly in horizontal direction
to fit 16:9 full screen display.
VCINE (Virtual Cinema)
A 2.35 image is stretched
vertically in both directions to
fill a 16:9 image.
PBP (Picture by Picture)
Enable the PBP function.
ACT (Active)
Switch to the active window
in PIP display mode.
PIP (Picture in Picture)
Enable the PIP function. Use
ARROW keys to adjust the
position of the PIP window.
See “PIP / PBP Function” on
page 29.
PIP+
Enlarge the size of PIP
window.
PIPShrink the size of PIP
window.
16
Runco CL-610 Owner’s Operating Manual
Installation
Push the battery cover and slide it off. Install the
two AAA batteries with the correct polarity and
then replace the cover.
Notes on Batteries
•
Make sure that the battery polarities are correct when installing the batteries.
•
Do not mix an old battery with a new one or different types of batteries.
•
If you will not use the remote control for a long time, remove the batteries to avoid
damage from battery leakage.
Notes on Remote Control Operation
•
Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver on the projector.
•
The usable range is up to 8 meters (26.25 feet) within a 45-degree horizontal angle
and a 15-degree vertical angle.
•
If the effective range of the remote control decreases, or it stops working, replace
the batteries with new ones.
•
The remote control may fail to operate if the infrared remote sensor is exposed to
bright sunlight or fluorescent lighting.
•
Ambient conditions may possibly impede the operation of the remote control. If this
happens, point the remote control at the projector, and repeat the operation.
•
The Ø icon appears on the screen when a button for an unavailable function is
pressed.
Runco CL-610 Owner’s Operating Manual
17
Remote Control
Installation
Installation
Considerations
Installation Type ➤
Proper installation of your projector will ensure the quality of your display. Whether you
are installing a projector temporarily or permanently, you should take the following into
account to ensure your projector performs optimally.
Choose the installation type that best suits your needs: front or rear screen, floor mount
or inverted mount.
Front Screen, Floor Mount Installation
Advantages
• Easy to set up
• Can be moved or changed quickly
• Easy to access
Considerations
• Shares floor space with audience
Front Screen, Inverted Mount (ceiling) Installation
Advantages
• Does not take up audience space
• Projector is unobtrusive
• Projector cannot be accidentally moved
Considerations
• Installation is more permanent
• It is more difficult to access the projector
Rear Screen, Floor Mount Installation
Advantages
• Projector is completely hidden
• Projector is easily accessed
• Usually good ambient light rejection
Considerations
• Requires separate room
• Installation cost is usually higher
Rear Screen, Inverted Mount (ceiling) Installation
Advantages
• Projector is completely hidden
• Usually good ambient light rejection
Considerations
• Requires separate room
• Installation cost is usually higher
Rear Screen, Floor Mount with Mirror
Advantages
• Projector is completely hidden
• Usually good ambient light rejection
• Requires less space behind screen than other
rear screen installations
Screen Type and Size ➤
Considerations
• Requires separate room
• Installation cost is usually higher
Front Screen Installations
In front screen installations the projector and audience are positioned in front of the
screen, which can be flat or curved.
Flat screens are recommended with this projector. They offer a gain of about 1 with
a viewing angle just less than 180°. This type of screen reflects incident light equally
in all directions so the audience can see the display from various angles.
Curved screens have a gain greater than 1 with a viewing angle much less than 180°.
This type of screen does not reflect incident light equally in all directions; instead, it
is concentrated in a viewing cone. The audience sitting within the viewing cone area
sees a brighter image than those sitting just outside this area. Runco generally does
not recommend use of curved screens due to excessive brightness and uncorrectable
geometrical distortion.
18
Runco CL-610 Owner’s Operating Manual
Installation
Rear screen installations
There are two basic types of rear screens: diffused and optical.
A diffusion screen has a surface that spreads the light striking it. Purely diffused
screens have a gain of less than 1. The main advantage of the diffused screen is its
wide viewing angle, similar to that of a flat screen for front screen projection. This type
of screen is suitable when a wide viewing angle is required but there is low ambient
room lighting.
Optical screens take light from the projector and redirect it to increase the light intensity
at the front of the screen. This reduces it in other areas. A viewing cone similar to that
of a curved, front-screen installation is created. This type of screen is better suited for
brightly lit rooms where the audience is situated within the viewing cone.
Screen size
Choose a screen size that is appropriate for your lens and application. The size of the
room and viewing distance are the defining factors; a rule of thumb is that the primary
viewing distance be 1.5 times the screen width.
To fill a screen with an image, the aspect ratio of the screen should be equal to the
aspect ratio of the image (expressed as the ratio of its width to its height). Standard
video from a VCR has a 4:3 or 1.33:1 aspect ratio. For example, to display a VCR
output with a 4:3 aspect ratio onto a 10-foot (3.05-meter) high screen, the width of
the screen must be at least 13.3 feet (4 meters).
Runco CL-610 Owner’s Operating Manual
19
Installation
Ambient Light ➤
Other Considerations ➤
Throw Distance ➤
In general, minimize or eliminate light sources directed at the screen. Contrast ratio
in your images will be noticeably reduced if light directly strikes the screen, such as
when a shaft of light from a window or floodlight falls on the image. Images may then
appear washed out and less vibrant.
Other considerations and tips that can help improve your installation:
•
Keep the ambient temperature constant and below 35°C (95°F). Keep the projector
away from heating and/or air conditioning vents. Changes in temperature may
cause drifts in the projector circuitry, which may affect performance.
•
Keep the projector away from devices that radiate electromagnetic energy such
as motors and transformers. Common sources of these include slide projectors,
speakers, power amplifiers and elevators.
Throw distance is the distance measured from your projector’s lens to the screen. This
is an important calculation in any projector installation as it determines whether or not
you have enough room to install your projector with a desired screen size and if your
image will be of the right size for your screen.
You can quickly estimate the throw distance by taking the width of the screen and
multiplying it by the lens throw ratio that is applicable to your projector:
•
The CL-610 has a minimum throw distance factor of 1.37 and a maximum throw
distance factor of 1.82.
•
The CL-610LT has a minimum throw distance factor of 1.86 and a maximum throw
distance factor of 2.47.
�������������������������
������������������������������������������������������������
���
���
����
����
��
��
The result of this calculation tells you roughly how far back the projector should be
positioned from the screen in order to project a focused image large enough to fill
the screen.
For example, with an 8-foot (96-inch) wide screen (the maximum recommended screen
width for this projector):
•
The CL-610 has a throw distance range of between 131.52 inches (3.34 meters)
and 174.72 inches (4.44 meters).
•
The CL-610LT has a throw distance range of between 178.56 inches (4.54 meters)
and 237.12 inches (6.02 meters).
20
Runco CL-610 Owner’s Operating Manual
Installation
➤
Vertical and Horizontal
Position
➤
Proper placement of the projector relative to the screen will yield a rectangular, perfectlycentered image that completely fills the screen.
Adjusting the Projection
Angle
Ideally, the projector should be positioned perpendicular to the screen and in such a
way that the lens center is aligned with either the top or bottom edge of the screen
area, and centered horizontally.
The top of the projected image is even with the lens center when the projector is
inverted (ceiling-mounted). Likewise, the bottom of the projected image is aligned with
the lens center when the projector is upright (as in a floor installation).
Ceiling Installation
Height
Ceiling
Projection Distance
x
Lens Center
Lens Center
Screen
Floor Installation
Height
Screen
Lens Center
Lens Center
x
Projection Distance
Floor
If it is not possible to align the projector and screen as shown above, you can tilt the
projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling
mount. For a floor installation, turn the four adjustable feet on the bottom of the projector
to adjust the projector height and/or projection angle.
If you do this, you may need to make keystone adjustments or vertically shift the image
using the on-screen display (OSD) controls, to compensate. For detailed instructions,
refer to On-Screen Display Menus, later in this manual.
Runco CL-610 Owner’s Operating Manual
21
Installation
Mounting ➤
There are several methods for mounting the projector. Depending on your chosen
installation, one method may be more suitable than another. In typical front and rear
screen installations the projector can be mounted to a secure and level surface, such
as a table or cart. Carts are useful when moving a projector during a presentation or
from site to site. If possible, lock the wheels when it’s in position to prevent it from
being moved during a presentation.
CEILING MOUNT—The projector can also be inverted and suspended from the ceiling
using a specially designed ceiling mount fixture. This type of mounting is recommended
for fixed installations and for those that want the projector out of sight or have a limited
space for projector and audience.
Use only the Runco-approved ceiling mount kit designed for your projector.
Folded Optics ➤
In rear screen applications where space behind the projector is limited, a mirror may
be used to fold the optical path, as shown below. The position of the projector and
mirror must be accurately set. If you are considering this type of installation, contact
your dealer for assistance.
22
Runco CL-610 Owner’s Operating Manual
Connections
When connecting your equipment, make sure to:
Connecting Video Inputs
1. Turn off all equipment before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly connected.
➤
DVD Player
Runco CL-610 Owner’s Operating Manual
23
Video / S-Video /
Component
(Interlaced Video)
Connections
The RGB BNC input (labeled COMP 2 / RGB) supports two kinds of HDTV formats:
Progressive component (DTV Y/PB/PR) and DTV RGB. The projector will automatically
detect the resolution.
Progressive Component ➤
(DTV Y/P B/P R)
Red Blue Green
DTV Source
RGBHV (DTV RGB) ➤
Vert Horiz Red
Blue Green
DTV Source
24
Runco CL-610 Owner’s Operating Manual
Connections
Connecting a Computer
(GBRHV)
Vert
Horiz
Red
Blue Green
This unit is compatible with the
following computer resolutions:
1024x768, 800x600 and 640x480.
PC or Notebook
(PC, RGB, Analog,
HD Component,
Progressive DVD)
Connecting an HDMI™
Device
Use an HDMI (High-Definition Multimedia
Interface) cable to connect the projector
to an HDMI device.
HDMI Source
(DVD player or HD
tuner with HDMI
or DVI out)
Runco CL-610 Owner’s Operating Manual
25
Connections
Connecting to AC Power
The CL-610 ships with various types of AC power cords. Choose the one that is
appropriate to your locale.
Plug the female end of the power cord into the AC receptacle on the rear of the projector
(AC 100V ~ 240V). Then, connect the other end to your AC power source.
Power
switch
26
Runco CL-610 Owner’s Operating Manual
Basic Operation
•
Turn on the main power switch. The
POWER LED will light orange.
•
Press the ON button on the remote
control to turn on the projector. The
POWER LED flashes orange during
the warm up period, then lights solid
green.
•
“Searching….” appears on the
screen before the projector identifies
the input signal, and remains there
until a valid signal is detected.
•
If an incompatible input signal exceeds
the range of the projector a “No signal
supported” message will be displayed
on the screen. This message remains
on the screen until you change the
input signal.
•
Adjust the projected image size with
the zoom ring on the lens. To focus the
image, rotate the focus ring on the
lens.
Turning on the Power
LIGHT
VID
ON
S-VID
COMP1
RGBHD
HDMI
Focus
Zoom in
To adjust the projector height or
projection angle, or to compensate for
a mounting surface that isn’t level, turn
the four adjustable feet on the bottom
of the projector.
Runco CL-610 Owner’s Operating Manual
COMP2
Adjusting the Zoom and
Focus
Zoom out
•
OFF
Adjusting Projector
Height or Projection
Angle
27
Basic Operation
Selecting Video Memory
MEM1
ISF
NIGHT
ISF
DAY
FACT
•
Press MEM1 to recall custom memory
settings.
•
Press ISF NIGHT to recall ISF Night
settings.
•
Press ISF DAY to recall ISF Day
settings.
NOTE: ISF settings must be calibrated
and stored by a certified ISF calibrator.
For more information, please go to
www.imagingscience.com.
•
Selecting an Aspect Ratio
ANA
16X9
4X3
LBOX
VWIDE
CINEMA
1
2
VCINE
Adjusting the Picture
BRT
CONT
COL
TNT
28
Press FACT (Factory) to restore factory
settings for the current source. An onscreen confirmation message appears.
Press FACT again to confirm.
Select an aspect ratio that suits the format of
the video signal. The following aspect ratios
are available.
•
CINEMA: The image in the Letterbox mode
is enlarged to a 16x9 image and the upper
and lower portions are compressed.
•
ANA16X9 (Anamorphic): A 4:3 image is
stretched horizontally to fit a 16:9 screen.
This setting is for 16:9 DVDs and HDTV
programs.
•
4 X 3 (Standard 4:3): The input signal is
scaled to fit a 4:3 display mode in the center
of the screen.
•
LBOX (Letterbox): An image in letterbox
format is enlarged to fit a 16:9 full screen
display; the upper and lower portions are
compressed.
•
VWIDE (Virtual Wide): This setting
transforms a 4x3 image to a 16x9 image.
•
VCINE (Virtual Cinema): A 2.35 image is
stretched vertically in both directions to fill
a 16:9 image.
•
Press BRT (Brightness) to adjust picture
brightness.
•
Press CONT (Contrast) to adjust picture
contrast.
•
Press COL (Color) to adjust color
intensity.
•
Press TNT (Tint) to adjust color tones.
Runco CL-610 Owner’s Operating Manual
Basic Operation
•
Press INFO to view information about the
active signal source and aspect ratio.
•
Press MENU to open or close the on-screen
menu.
•
Use the arrow buttons (▲,◄,▼,►) to select
menu items or make adjustments.
•
Press ENTER or ► to enter the setting of
items in the menu, or press EXIT to leave
and save the setting of items in the menu.
•
When you turn on the projector, it searches
for the input source you selected last
time.
•
You may select the input source directly
on the remote control.
•
For PIP (Picture In Picture) and PBP (Picture
By Picture) purposes, there are two groups
of inputs separated by their display modes:
INFO
RVR
ENTER
EXIT
MENU
For more information
on settings, See “OnScreen Display Menus”
on page 31.
VID
PBP
S-VID
COMP1
RGBHD
HDMI
ACT
PIP
COMP2
PIP+
PIP-
Video group: Video, S-Video and
Component Y/CB/CR inputs.
Graphic (HD) group: HDMI and RGB/
Component HD inputs.
•
PIP / PBP shows one input from the
Graphic group within or beside one input
from the Video group.
•
Press PBP to enable the PBP function.
Press PBP again to switch the screens
left to right. Press PBP again to turn PBP
off.
•
Press ACT (Active) to switch to the active
window. You can only change the input
signal settings in the active window.
•
Press PIP to enable the PIP function.
Press PIP again to switch the main window.
Press PIP again to turn PIP off.
•
Press PIP+ or PIP- to adjust the size of
the PIP window.
•
Adjust the position of the PIP window with
the ARROW keys (▲,◄,▼,►).
Runco CL-610 Owner’s Operating Manual
Setting the Menu
29
Selecting the Input
Source
PIP / PBP Function
Basic Operation
Turning off the Power
•
Press the OFF button to turn off the
projector.
•
The POWER LED will blink green and the
fans will speed up for a quick cool-down.
The projector will not respond to any
command for 90 seconds.
•
The POWER LED will light solid orange
once the cooling down cycle has
completed.
•
The fans will run for three minutes to
cool.
•
You can turn the projector back on after
approximately two minutes.
30
LIGHT
VID
ON
OFF
S-VID
COMP1
RGBHD
HDMI
COMP2
Runco CL-610 Owner’s Operating Manual
On-Screen Display Menus
INFO
RVR
ENTER
EXIT
This unit is equipped with an on-screen
display (OSD) menu for making adjustments
and changing settings. There are five menu
languages; see the Language setting under
“Installation” on page 35.
Using the Menu
MENU
Press the Menu button to turn on/off the OSD menu.
•
NOTE: If the Main Menu is displayed, you can also press Exit to turn it off.
•
Use the arrow buttons (▲,◄,▼,►) to select items in the menu or to make various
adjustments.
•
Press Enter or ► to select an item to change, or press Exit to leave and save the
setting of items in the menu.
Runco CL-610
Video
S-Video
Component1
Component2
RGB-HD
HDMI
-----------------------Aspect Ratio
Installation
Option
Set Up
ISF Calibration
Main Menu
>
Source selection and picture quality adjustments
Aspect Ratio selection
Installation selection
Option selection
Setup selection
ISF Calibration selection
When the Menu button is pressed, the Main Menu (shown above) appears on the
screen. Use the ▲ or ▼ button to move to an item, then press Enter to select it.
The active source is indicated by an arrow (>) to the left of the source; in the example
above, Video is the active source. To select a different source, use the ▲ or ▼ button
to highlight it and press Enter or ►.
Runco CL-610 Owner’s Operating Manual
31
On-Screen Display Menus
Runco CL-610
Picture Quality
Adjustments
>
Video
S-Video
Component1
Component2
RGB-HD
HDMI
-----------------------Aspect Ratio
Installation
Option
Setup
ISF Calibration
Adjustment
Brightness
Contrast
Color
Tint
Sharpness
Filter
Color Temperature
ICC Selection
Store Image Settings
Restore Image Settings
To access the picture quality adjustments, press Menu, highlight the active source and
press Enter or ►. The picture quality sub-menu then appears (see above).
To adjust a setting, highlight it with the ▲ or ▼ button and press Enter to activate a
scroll bar for that setting. Use the ◄ or ► keys to change the setting. When finished,
press Exit.
Brightness ➤
Select Brightness to adjust the black level of the projected image (0 = minimum;
60 = maximum).
Contrast ➤
Select Contrast to adjust the white level of the projected image (0 = minimum;
32 = maximum).
Color ➤
Select Color to adjust the color level (saturation) of the projected image (0 = minimum;
64 = maximum).
Tint ➤
Select Tint to adjust the hue of the projected image (0 = minimum; 30 = maximum).
Sharpness ➤
Select Sharpness to adjust the sharpness of the projected image (-14 = minimum;
+20 = maximum). This setting has no effect if the Sharpness Filter is set to 0 (refer to
the next paragraph).
Filter ➤
The Filter setting controls the behavior of the Sharpness control. The available
settings depend on the vertical resolution of the input signal, as follows:
•
With a 480i signal, you can apply the sharpness control to either the input signal
(1), the output signal (2), both (3) or neither (0).
•
With a 480p or higher-resolution signal, the sharpness control is applied only
to the output signal and only when you set the Sharpness filter to “on” (1).
32
Runco CL-610 Owner’s Operating Manual
On-Screen Display Menus
ICC Selection
Store Image Settings
➤
Original lamp color temperature
5400 kelvins
6500 kelvins
8500 kelvins
Custom
Custom
➤
-------
Color Temperature
➤
0
1
2
3
4
5
➤
The CL-610 has six memory settings for Color Temperature. Four of these settings
are factory set to default as follows:
Restore Image Settings
Color Temperature
2 -
+
Custom 4 and 5 memory are installer-adjustable and can be used to create custom
settings. There are nine adjustable “white balance” parameters available for the Custom
4 and 5 settings (three each for red, green and blue). These are described later in this
section; refer to “Set Up.”
NOTE: You must enter a passcode in order to enter the Set Up menu.
Use the ICC Selection menu to select the color space that is appropriate for the
source signal, to achieve optimal color balance.
NOTE: The International Color Consortium (ICC) is a group of imaging product vendors
that promotes and develops cross-platform, vendor-neutral color measurement and
management standards.
If you select NTSC, HDTV or PAL, you can make further adjustments to individual color
characteristics in the ICC Adjust sub-menu under the ISF Calibration menu, described
later in this section. (The Standard color is factory-set and not adjustable.)
Once the desired adjustments have been entered, select Store Image Settings to
save these settings into the “Memory 1” memory location.
To recall stored custom image quality settings, select Restore Image Settings and
choose “Memory 1,” “ISF Night” or “ISF Day.”
Runco CL-610 Owner’s Operating Manual
33
On-Screen Display Menus
Runco CL-610
Aspect Ratio
>
Video
S-Video
Component1
Component2
RGB-HD
HDMI
-----------------------Aspect Ratio
Installation
Option
Setup
ISF Calibration
Aspect Ratio
Anamorphic (16:9)
Standard (4:3)
Letterbox
Virtual Wide
Cinema
Virtual Cinema
To access the Aspect Ratio adjustments, press Menu, then press the ▲ or ▼ arrows
to highlight Aspect Ratio and press Enter. The Aspect Ratio sub-menu then appears
(see above).
There are six aspect ratios available that can be selected for video signal inputs:
• ANAMORPHIC (16:9)
The image is compressed vertically,
but anamorphic software will appear
properly proportioned. This is best
suited for use with 16:9 DVDs and HDTV
programming.
Active Image Area
• LETTERBOX
The image in the Letterbox mode is
stretched vertically, and the top and
bottom portion ‘blanked off’. This ratio
is best suited for LaserDisc movies or
non-anamorphic DVDs.
Active Image Area
• STANDARD (4 x 3)
The input signal is scaled to fit in the
center of the 16:9 screen.
• VIRTUALWIDE
A 4:3 image is transformed into a 16x9
image.
Active
Image Area
34
Runco CL-610 Owner’s Operating Manual
On-Screen Display Menus
Aspect Ratio (continued)
• CINEMA
The image in the Letterbox mode is
enlarged to a 16x9 image and the upper
and lower portions are compressed.
• VIRTUAL CINEMA
A 2.35 image is stretched vertically in
both directions to fill a 16:9 image.
Runco CL-610
Installation
>
Video
S-Video
Component1
Component2
RGB-HD
HDMI
-----------------------Aspect Ratio
Installation
Option
Setup
ISF Calibration
Installation
Language
Picture Orientation
Keystone Adjust
Background Color
RS-232 Baud Rate
Blue Image
To access the Installation adjustments, press Menu, then press the ▲ or ▼ arrows
to highlight Installation and press Enter. The Installation sub-menu will then appear
(see above). Press the Exit button to return to the previous menu or press the Menu
button to close all menus.
NOTE: When you change a setting in the Installation menu, the change takes effect
immediately; you do not need to press Enter afterwards. (Press Exit to return to the
previous menu or Menu to exit.)
Runco CL-610 Owner’s Operating Manual
35
On-Screen Display Menus
Language ➤
Picture Orientation ➤
Keystone Adjust ➤
Press the ▲ or ▼ arrows to select from the available
Languages: English, French, Spanish, German and
Italian.
Press the ▲ or ▼ arrows to select the projector’s Picture
Orientation. The projector can be installed on a ceiling
or in a rear-screen configuration with one or more mirrors.
There are four settings: Floor Front, Ceiling Front, Floor Rear
and Ceiling Rear.
Language
>
English
Francais
Espanol
Deutsch
Italiano
Picture Orientation
>
To correct distortion resulting from the angle of the projection,
select Keystone Adjust and use the ◄ or ► arrows to
make the image rectangular.
Floor Front
Ceiling Front
Floor Rear
Ceiling Rear
Keystone Adjust
-
+
0
NOTE: Runco recommends that the keystone feature not be
used unless absolutely necessary, as it may cause artifacts
in the image.
Background Color ➤
RS-232 Baud Rate ➤
Press the ▲ or ▼ arrows to select the image Background
Color (blue or white). The Background Color appears when
no incoming signal is present.
Press the ▲ or ▼ arrows to select the projector’s RS-232
Baud Rate. This function is used to change the transfer
rate of the RS-232 connection. (This setting must match the
data rate of the device connected to the RS-232 input.)
Background Color
>
Blue
White
RS-232 Baud Rate
>
9600
38400
115200
Blue Image ➤
Press the ▲ or ▼ arrows to turn the Blue Image Off or On.
This feature removes all red and green color information from
the image, and is useful for color-calibrating the projector
or other video components.
36
Blue Image
>
Off
On
Runco CL-610 Owner’s Operating Manual
On-Screen Display Menus
Runco CL-610
Option
>
Video
S-Video
Component1
Component2
RGB-HD
HDMI
-----------------------Aspect Ratio
Installation
Option
Setup
ISF Calibration
Option
Reset Image Settings
Sleep Timer
Lamp Hours
OSD Timer
OSD Position
PC & HD Adjust
PIP/PBP Set Up
DNR
To access the Option adjustments, press Menu, then press the ▲ or ▼ arrows to
highlight Option and press Enter. The Option sub-menu will then appear (see above).
Press the Exit button to return to the previous menu or press the Menu button to
close all menus.
Sleep Timer
Lamp Hours
➤
OSD Timer
➤
The Sleep Timer automatically puts the projector into standby
mode after the amount of time you specify here. (A warning
appears on-screen one minute before this is to occur.)
➤
No
Reset Image Settings
➤
Reset Image Settings
Load default of
current source
Confirm?
➤
To restore the default image settings for the current input
source ONLY, press the ► arrow key to highlight “Yes” then
press Enter.
OSD Position
Yes
Sleep Timer
-
0 + Minutes
Press the ◄ or ► arrows to set the timer for anywhere from
10 minutes to 3 hours, in 10-minute increments. To disable
the Sleep Timer, set it to 0.
Press the Enter button to check the total time of lamp
usage.
Lamp Hours
+8
+30
Press the ◄ or ► arrows to set the OSD Timer. This
timer controls how long the menus remain on-screen after
selecting them. Select from 0 to 60 seconds, in 3-second
increments. When you set the OSD to 0, the menus remain
on-screen until you hide them by pressing Menu.
Press the ◄ or ► arrows to adjust the horizontal and vertical
position of the OSD.
Runco CL-610 Owner’s Operating Manual
37
Hours
Minutes
OSD Timer
+60 -
+
OSD Position
Hor.
0
Ver.
+20
On-Screen Display Menus
PC & HD Adjust ➤
Press Enter to display the PC & HD Adjust menu. Use these
settings to fine-tune 480p and higher-resolution signals for
optimum picture quality.
Auto: Adjusts the phase, frequency and position
automatically.
•
•
Freq.: Adjusts the frequency of the signal.
•
Phase: Adjusts the phase of the input signal (similar to
tracking on a VCR).
•
H. Pos.: Adjusts the horizontal position of the image.
•
V. Pos.: Adjusts the vertical position of the image.
PC & HD Adjust
Auto
Yes?
Freq.
0
Phase
+10
H.Pos.
0
V.Pos.
0
NOTE: To adjust the image position with a 480i source, use
the Image Shift controls in the Set Up menu, described on
page 41.
PIP / PBP Set Up ➤
Press the ▲ or ▼ arrows to select PIP/PBP Enable, then press Enter.
Press the ▲ or ▼ arrows to select Off or On, then press Enter.
PIP/PBP Set Up
PIP/PBP Enable
PIP/PBP Enable
PIP Set Up
PBP Set Up
PIP Set Up ➤
Off
On
Press the ▲ or ▼ arrows to select PIP Set Up, then press Enter.
Press the ▲ or ▼ arrows to select PIP Off, Graphic in Video or Video in
Graphic, then press Enter.
PIP Set Up
PIP/PBP Set Up
PIP Off
Graphic in Video
Video in Graphic
PIP/PBP Enable
PIP Set Up
PBP Set Up
PBP Set Up ➤
Press the ▲ or ▼ arrows to select PBP Set Up, then press Enter.
Press the ▲ or ▼ arrows to select PBP Off, Graphic by Video or Video by
Graphic, then press Enter.
PBP Set Up
PIP/PBP Set Up
PBP Off
Graphic by Video
Video by Graphic
PIP/PBP Enable
PIP Set Up
PBP Set Up
DNR ➤
Press the ◄ or ► arrows to adjust the Digital Noise Reduction (DNR). DNR is useful
for clearing up noisy RGB images such as those from a PC. Adjust as desired, keeping
in mind that reducing noise (which reduces high frequencies) may also soften the
image.
-
+
0
38
Runco CL-610 Owner’s Operating Manual
On-Screen Display Menus
To access advanced picture quality adjustments, use the up- or down-arrow keys to
highlight Set Up and press Enter. Use the number buttons on the remote to enter the
Set Up menu passcode when prompted and press Enter again. Then, press MENU
on the remote control.
Setup
Runco CL-610
>
Video
S-Video
Component1
Component2
RGB-HD
HDMI
-----------------------Aspect Ratio
Installation
Option
Set Up
ISF Calibration
Passcode
Please Enter
Passcode To
Access Service
Screen
Passcode
Please Enter
Passcode To
Access Service
Screen
***
Confirmed
NOTE: You only need to enter the Set Up menu passcode the first time you select that
menu after turning on the projector.
In all but the most unusual situations, the appropriate “Gamma Selection” (see below)
will produce accurate colors and a satisfying contrast level. However, it is sometimes
necessary to adjust the red, blue and green gamma curves individually. To do this,
select Gamma from the White Balance sub-menu and use the left- and right-arrow
buttons to manipulate the on-screen slidebars.
Gain: Use the Gain controls in the White Balance sub-menu to correct color imbalances
in the bright areas of the image. A good way to do this is to use a test pattern consisting
mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas
contain traces of red, green or blue, decrease the Gain for that color.
Offset: Use the Offset controls in the White Balance sub-menu to correct color
imbalances in the dark areas of the image. A good way to do this is to use a test pattern
consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray
areas contain traces of red, green or blue, decrease the Offset for that color.
Store Color Temp.4/Store Color Temp.5: When you are finished adjusting the
Gamma, Gain and Offset, select Store Color Temp.4 or Store Color Temp.5 to store
your settings. To recall them, set the Color Temperature to +4 or +5 in the Image
Adjustment menu (refer to “Picture Quality Adjustments,” earlier in this section).
Runco CL-610 Owner’s Operating Manual
39
➤
Gamma: “Gamma” is a global setting that determines how gray shades are displayed
between minimum input (black) and maximum input (white) for all signals. A good
gamma setting helps to optimize blacks and whites while ensuring smooth transitions
for the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast”
controls, the overall tone of your images can be lightened or darkened without changing
the extremes and all images will be more vibrant while still showing good detail in dark
areas when using the “Gamma” control.
White Balance
On-Screen Display Menus
Gamma Selection ➤
SD Enhance ➤
The normal gamma setting of 2.2 is correct for almost all
signals and conditions. If excess ambient light washes out the
image and it becomes difficult or impossible to see details in
dark areas, lower the gamma setting to compensate. This will
improve contrast while maintaining good details for blacks.
Conversely, if the image is washed out and unnatural, with
excessive detail in black areas, increase the setting. Again,
good gamma improves contrast while maintaining good details
for blacks and whites.
2.8
2.5
2.2
1.0
RUNCO Enhance 1
RUNCO Enhance 2
ISF Day
The SD Enhance menu gives you options for improving
the quality of standard-definition, 480i images. (For 480p
and higher-definition images, the controls in this menu are
disabled.) Keep in mind that these controls add frequencies
that are not present in the original signal, and may make
images appear “noisy” if misused.
H Enhance
V Enhance
Chroma Enhance
H Threshold
V Threshold
Chroma Threshold
Gamma Selection
H Enhance/V Enhance: These controls can improve the
apparent horizontal and/or vertical resolution of the image.
Chroma Enhance: This control adds chroma (color
information) to the input signal and can make colors appear
more vibrant and saturated.
H Threshold/V Threshold/Chroma Threshold: Set these to
+11 or higher to activate the enhancement controls described
above. Generally, the higher the threshold, the more noticeable
the enhancements you make will be.
Image Over Scan ➤
Image Over Scan pushes the outside edge of the active
picture area of the video signal out beyond the edge of the
display area.
Image Over Scan
+4 %
Some television programs are produced based on the
assumption that older television sets may not display the outer
edges of the broadcast picture area. Over scan effectively trims
away these inactive, outer edges and enlarges the remaining
portion of the image to fill the display area.
Select from 1% to 10% of Over Scan, as desired.
For HDTV, DVDs and other video sources, Over Scan is
generally not necessary or desirable.
Image Shift ➤
The Image Shift menu allows you to precisely center the
image on the screen. (These controls are available only with
a 480i source signal.)
Horizontal
Vertical
Horizontal: This control moves the image right or left within
the area of available pixels.
Vertical: This option moves the image up or down within the
area of available pixels.
40
-
+
0
Runco CL-610 Owner’s Operating Manual
On-Screen Display Menus
NOTES:
1. To adjust the image position with a 480p or higherresolution source, use the PC & HD Adjust controls in the
Option menu, described on page 38.
2. The values shown represent where the approximate center
of the image lies in relation to the total number of pixels
available horizontally or vertically. This varies widely according
to the signal; watch the image while adjusting.
Video Black Level
>
0 IRE
7.5 IRE
This control compensates for incoming elevated black levels
present in certain video signals, and ensures that blacks in
the display are neither “crushed” (where dark grays appear
black) nor excessively elevated (where blacks appear dark
gray). By default, the projector automatically determines the
best setting according to the type of incoming video signal:
Video Black Level
Select Lamp Power from the Set Up Menu to adjust the lamp
output level. You can choose to run the lamp as bright as
possible (250W; this is the default setting) or you can choose
the lower (200W) setting. Generally, lower lamp output can
prolong the life of the lamp, but decreases brightness.
Lamp Power
The Remote Control menu shows you the primary and
secondary infrared (IR) codes assigned to the CL-610. The
Primary IR code is permanently set to +20. The secondary
IR code is also +20.
➤
0
➤
+
Amplitude Adjust
➤
-
The Amplitude Adjust menu allows you to fine-tune the image
aspect ratio by stretching it horizontally or vertically, in small
increments. The Horizontal control adjusts the image width
while keeping the height constant. Similarly, the Vertical
control adjusts the image height while keeping the width
constant.
➤
Horizontal
Vertical
Remote Control
•
0 IRE – Used for DVD output with “enhanced black,”
SECAM, most PAL standards and Japanese NTSC.
•
7.5 IRE – Used for most NTSC video signals.
For some types of video, you may want to override the setting.
Generally, if black appears crushed when brightness = 30,
choose “0 IRE”. If black appears excessively elevated, use
“7.5 IRE.”
Lamp Power
Primary
Secondary
250 W
+20
+20
You can change the secondary IR code if either:
•
Another device in the theater (a DVD player, for example)
is responding to commands from the CL-610 remote
control in ways that are unpredictable or undesirable.
•
You have multiple CL-610 projectors and want to
control them independently, as opposed to broadcasting
commands from a single remote to all of them. In this
scenario, you can use multiple remotes programmed to
Runco CL-610 Owner’s Operating Manual
41
On-Screen Display Menus
use different IR codes. Or, you can use a single remote
and change the IR code as needed to address a specific
projector.
When you change the secondary IR code, the remote sends
that code instead of the primary IR code.
NOTE: The Remote Control menu is read-only and need not
be visible in order to change the secondary IR code.
To simultaneously change the secondary IR code and
synchronize that remote with a projector, point the remote at
the projector, then press and hold ◄ and ► simultaneously
for five seconds. The Remote Control edit window, shown
at right, appears. Type a new, two-digit code.
Remote Control
Secondary
+20
The procedure for changing the secondary IR code on the
remote only is the same, except that you point the remote
away from the projector.
Reset Lamp Timer ➤
When you replace the projector lamp, you should also reset
the lamp timer. To do this, select Reset Lamp Timer from
the Set Up menu. Press the right-arrow key on the remote to
highlight “Yes,” then press Enter to confirm the reset.
Reset Lamp Timer
Reset only if you
replace lamp
Are you sure?
NOTE: Reset the Lamp Timer ONLY after you replace
the lamp. Otherwise, the reported “Lamp Hours” will be
inaccurate.
No
Yes
WARNING! Do not exceed the recommended lamp life
of 2000 hours. An old lamp becomes increasingly fragile and
prone to sudden failure.
Fan Control ➤
Select Fan Control from the Set Up Menu to control the
operation of the projector’s cooling fan.
Mode: In most cases, the default Fan Control Mode (Auto
Normal) will maintain the correct operating temperature. If
the lamp frequently turns off due to overheating, or in certain
high-altitude operating environments, you may need to change
this setting to Auto Hi. Altitude or Manual.
Fan Speed: If you set the Fan Mode to Manual, select Fan
Speed and use the on-screen slidebar to adjust the speed.
After changing either of these settings, press Exit to return
to the previous menu.
Return to User OSD ➤
Fan Control
Mode
Fan Speed
Fan Control
> Auto Normal
Auto Hi. Altitude
Manual
Fan Speed
+2
-
+
To exit the Set Up menu, use the up- or down-arrow keys to
highlight Return to User OSD and press Enter.
To return to the Set Up menu, select it from the Main Menu,
press Enter twice, then press MENU on the remote control.
(You do not need to re-enter the passcode.)
42
Runco CL-610 Owner’s Operating Manual
On-Screen Display Menus
The CL-610 has been designed to incorporate setup and calibration standards
established by the Imaging Science Foundation (ISF). The ISF has developed carefully
crafted, industry-recognized standards for optimal video performance and has
implemented a training program for technicians and installers to use these standards
to obtain optimal picture quality from Runco video display devices. Accordingly, Runco
recommends that setup and calibration be performed by an ISF certified installation
technician.
ISF Calibration
All signal types require separate processing. Therefore, you need to calibrate each
and every input separately.
To access the ISF Calibration menu, use the up- or down-arrow keys to highlight ISF
Calibration and press Enter. Use the number buttons on the remote control to enter
the ISF Calibration menu passcode, then press Enter again.
NOTE: You only need to enter the ISF Calibration menu passcode the first time you select
that menu after turning on the projector.
Runco CL-610
>
***
Confirmed
To restore the ISF default image settings for the current input
source ONLY, press the ► arrow key to highlight “Yes” then
press Enter.
Reset Picture Adjust
These settings are described in the “Picture Quality
Adjustments” section (refer to page 32).
Picture Adjust
These settings are described in the previous section, “Set
Up.”
➤
White Balance
These settings are described in the previous section, “Set
Up.”
➤
Gamma Selection
This setting is described in the “Installation” section (refer
to page 35).
➤
No
Passcode
Please Enter
Passcode To
Access ISF
Calibration
Screen
➤
Reset Picture Adjust
Restore ISF Default.
Confirm?
Passcode
Please Enter
Passcode To
Access ISF
Calibration
Screen
➤
Video
S-Video
Component1
Component2
RGB-HD
HDMI
-----------------------Aspect Ratio
Installation
Option
Setup
ISF Calibration
Blue Image
Yes
Runco CL-610 Owner’s Operating Manual
43
On-Screen Display Menus
ICC Adjust ➤
Use the ICC Adjust controls to customize the stored NTSC,
HDTV and/or PAL color characteristics. To do this, select
the color space to modify. Then, select a component color
(Red, Green, Blue, Yellow, Cyan or Magenta).
Color
For each component color, you can adjust the following:
Intensity
+100
Intensity: This slidebar adjusts the intensity -- also known
as luminance -- of a given color.
Sat.
+100
Hue
ICC Adjust
NTSC
R G
B
M
Y
C
C
M
0
Store Setting
Sat.: This slidebar adjusts the color saturation level -- the
amount of that color in a video image. Lower settings
produce less saturated colors; a setting of “0” removes that
color from the image entirely. If the saturation is too high,
that color will be overpowering and unrealistic.
Hue: This slidebar adjusts the red/green color hue for true
color reproduction of video signals. For best results, adjust
tint while displaying an external color bars test pattern.
Otherwise, it is recommended that Hue remain at its default
setting.
When you have finished customizing the color space, select
Store Setting and press Enter.
Store Settings ➤
When you have finished calibration, select Store Image
Settings and choose “Memory 1,” “ISF Night“ or “ISF Day”
to store your settings.
To recall stored custom image quality settings, select
Restore Image Settings from the Adjustment menu (refer
to “Picture Quality Adjustments,” earlier in this section) and
choose “Memory 1,” “ISF Night“ or “ISF Day.” Or, simply use
the corresponding buttons on the remote control.
Splash Screen Timer ➤
ISF Enable ➤
Press the ◄ or ► arrows to set the Splash Screen Timer.
This timer controls how long the startup (ISF and Runco
logo) image stays on-screen after you turn on the projector.
Select from 5 to 60 seconds, in 1-second increments. When
finished, press Exit.
Use ISF Enable to control the display of the ISF logo on
the CL-610 splash screen upon power-up.
Store Settings
Memory 1
ISF Night
ISF Day
Splash Screen Timer
+20
-
+
ISF Enable
>
Off
On
44
Runco CL-610 Owner’s Operating Manual
Lamp Replacement (Contact Your Runco Dealer)
The lamp should be replaced when it reaches the end of its life (typically 2000 hours),
or sooner if a noticeable degradation in brightness occurs.
1. Turn off the projector and unplug the power
cord. Allow the projector to cool down for
approximately 45 minutes prior to removing
the lamp assembly for replacement.
2. Remove the two screws from the lamp cover.
3. Remove the lamp cover.
4. Remove the two screws from the lamp module.
5. Pull the lamp module straight out to remove it.
6. Insert the new lamp module securely and replace
the two screws.
7. Replace the lamp cover at the right side first as
shown and secure it with the two screws.
8. Turn on the power and go into the Setup/Reset
Lamp Timer menu to reset the lamp timer. Refer
to “Set Up” in the previous section, On-Screen
Display Menus.
Runco CL-610 Owner’s Operating Manual
45
Lamp Replacement
This page is intentionally left blank.
46
Runco CL-610 Owner’s Operating Manual
Troubleshooting
PROBLEM
The projector
does not turn on
No picture
POSSIBLE CAUSE
REMEDY
There is no power from the
power cable.
Plug the power cord into the
AC power socket on the rear of
the projector and an electrical
outlet.
The power switch is not turned
on.
Turn on the power switch.
The projector was turned on
again within the cool down
time.
Wait until projector completes
the cool down time.
Lamp cover is not attached
well.
Correctly attach the lamp cover.
The lamp cover is not correctly
attached.
Correctly attach the lamp cover.
The projector is not correctly
connected to the input source
device.
Check the connection.
The input signal has not been
correctly selected.
Select the correct input signal
with the SOURCE input keys:
VID, S-VID, COMP1, COMP2,
RGBHD or HDMI.
TEMP LED or LAMP LED
blinking.
Please contact your Runco
dealer for assistance.
Image is unstable The connection cables are not
connected to the projector.
Correctly connect the cables to
the appropriate terminals.
Picture is blurred
The projection lens is not
correctly focused.
Adjust the focus of the
projection lens with the focus
ring.
The projector and the screen
are not aligned squarely.
Adjust the projection angle and
direction, and the height of the
projector.
Remote control
does not work
correctly
The batteries are exhausted.
Replace both batteries with
new ones.
LAMP LED blinks
red
The cooling fan does not work
well.
Please contact your Runco
dealer for assistance.
The temperature inside the
projector is extremely high.
Check that the ventilation holes
are not blocked.
The lamp has exceed its
specified usage hours.
Replace the lamp with a new
one.
The lamp has burned out.
Replace the lamp with a new
one.
LAMP LED blinks
red; POWER LED
is green
Runco CL-610 Owner’s Operating Manual
47
Troubleshooting
This page is intentionally left blank.
48
Runco CL-610 Owner’s Operating Manual
RS-232 Setup
1. Connect a D-Sub 9-pin female-to-RJ-11 adapter (not included) to a COM port
on your PC. The adapter must be wired as follows:
RS-232 Pin Assignments
D-Sub 9-pin female
4-pin RJ-11
Function
2
2
Transmit Data
3
3
Receive Data
5
1, 4
Ground
1, 4, 6, 7, 8, 9
--
Not Connected
2. Connect the COM port to the RS-232 port on the projector. Use a standard,
4-wire RJ-11 telephone cable, wired straight-through.
RJ-11 to D-Sub 9-pin (not included)
Yellow
Green
1
2
3
4
Yellow
Green
5
4
9
3
8
1
2
7
6
D-Sub 9-pin female
Black
Red
Black
Red
3. Start a terminal session on your PC using a terminal-emulation program, such
as HyperTerminal.
4. Configure the COM port on the PC as follows: no parity, 8 data bits, 1 stop bit
and no flow control. Set the baud rate to match that of the projector (115200,
38400 or 9600).
5. Press Enter. You should see a command prompt (>) in the terminal window.
6. Type the desired command from the table that follows and press Enter. For
example, to set the aspect ratio to Letterbox, type x063x <Enter>.
Runco CL-610 Owner’s Operating Manual
49
Connecting RS-232 to the
Projector
RS-232 Setup
RS-232C Control Codes
NOTES:
1. All codes are in the ASCII format.
2. A carriage return is required after each command.
3. The projector will not accept RS-232 commands for 20 seconds after it is turned
on or off.
Code
Function
Code
Function
x001x
Power On
x049x
Load default of current source
x002x
Power Off
x051x
Single source, full-screen
x003x
Menu
x052x
PIP - graphics on video
x004x
Enter
x053x
PIP - video on graphics
x005x
Exit
x054x
PBP - graphics by video
x006x
Up (arrow key)
x055x
PBP - video by graphics
x007x
Down (arrow key)
x056x
PIP - increase sub-window size
x008x
Left (arrow key)
x057x
PIP - decrease sub-window size
x009x
Right (arrow key)
x058x
Set PIP/PBP active window
x011x
Show active source and
aspect ratio information
x061x
Anamorphic (16:9) aspect ratio
x062x
Standard (4:3) aspect ratio
x021x
Keypad 1
x063x
Letterbox aspect ratio
x022x
Keypad 2
x064x
VirtualWide aspect ratio
x023x
Keypad 3
x065x
Cinema aspect ratio
x024x
Keypad 4
x066x
Virtual Cinema aspect ratio
x025x
Keypad 5
x071x
RS-232 baud rate = 9600
x026x
Keypad 6
x072x
RS-232 baud rate = 38400
x027x
Keypad 7
x073x
RS-232 baud rate = 115200
x028x
Keypad 8
x081x
Image orientation = floor front
x029x
Keypad 9
x082x
Image orientation = ceiling front
x030x
Keypad 0
x083x
Image orientation = floor rear
x031x
Store image settings to
Memory 1
x084x
Image orientation = ceiling rear
x032x
Store image settings to
ISF Night
x091x
Lamp Power = 200W
x092x
Lamp Power = 250W
x033x
Store image settings to
ISF Day
x121x
OSD Language = English
x122x
OSD Language = French
x046x
Restore image settings from
Memory 1
x123x
OSD Language = Spanish
x124x
OSD Language = German
x047x
Restore image settings from
ISF Night
x125x
OSD Language = Italian
x048x
Restore image settings from
ISF Day
50
Runco CL-610 Owner’s Operating Manual
RS-232 Setup
Code
Function
x131x
Switch to Composite input
x132x
Switch to S-Video input
x133x
Switch to RGB-HD input
x134x
Switch to DVI input (HDMI)
x135x
Switch to Component 1 input
x136x
Switch to Component 2 input
x156x
Background Color = Blue
x157x
Background Color = White
x181x
Toggle Blue Image on/off
Runco CL-610 Owner’s Operating Manual
RS-232C Control Codes
(continued)
51
RS-232 Setup
This page is intentionally left blank.
52
Runco CL-610 Owner’s Operating Manual
Specifications
Projector Type:
Digital Light Processing™ (DLP™), Single-Chip SuperOnyx™
DMD™
Native Resolution:
1280 x 720 (16:9)
Aspect Ratios:
4:3, Letterbox, 16:9 Anamorphic, VirtualWide™, Cinema,
Virtual Cinema™
Video Standards:
NTSC, PAL, SECAM
DTV Compatibility:
480p, 576p, 720p, 1080i
Scan Frequency:
Horizontal: 15-80 kHz;
Vertical: 50-100 Hz
Picture Size
(16:9 screens):
Recommended Width: 72 in. (1.83 m) to 96 in. (2.44 m)
Capable of screen widths between 48 in. (1.22 m) and 240 in.
(6.10 m)
Throw Distance
(Factor x Screen
Width):
CL-610
1.37 to 1.82 x Screen Width
CL-610LT
1.86 to 2.47 x Screen Width
Horizontal and
Vertical Offset:
- Lens is fixed
- Horizontal and/or vertical image shift via OSD controls
- Bottom edge of projected image is aligned with lens center
when projector is upright
- Top edge of projected image is aligned with lens center
when projector is inverted (ceiling-mounted)
Lamp:
210W NSH
Lamp Life:
2000 hours
Inputs:
(1) Composite Video, (1) S-Video, (1) RGB/Component (via
BNC), (1) RCA Component Video, (1) HDMI, (1) RS-232
12V Output:
Max. 0.25 Amps, active when the projector is on
Runco CL-610 Owner’s Operating Manual
53
Specifications
Brightness and
Contrast:
Cinema Standards Measurement System (CSMS)
Specifications
- Brightness: 12.3 to 19.3 foot-Lamberts (fL)
- Contrast Ratio: 185:1 to 205:1
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to ANSI/
NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial
movie theaters to express image brightness at the screen surface.
The Society of Motion Picture and Television Engineers (SMPTE)
specifies 16 fL as the target image brightness for film-based
projectors using an open gate (without film in the projector). More
importantly, today SMPTE specifies 12 fL as the target image
brightness in Digital Cinema theaters. The foot-Lambert measurement
is dependent on screen size, screen gain and projector light output.
Home Theater Calibration Specifications
- Light Output: 395 to 526 ANSI Lumens
- Contrast Ratio: 185:1 to 205:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
- Light Output: 1150 ANSI Lumens
- Contrast Ratio: 1400:1 to 2200:1
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with
other manufacturers’ projectors. These measurements are typically
taken at 9,000K to 13,000K to get expected performance data
when the projector is used in professional, commercial and industrial
displays.
Power Requirements: 100 to 240V AC, 50/60Hz, 310W
Operating
Environment:
41ºF to 95ºF (5º to 35ºC); 20-80% humidity (non-condensing)
Dimensions:
Width: 16.5 in. (419.1 mm)
Depth: 16.31 in. (414.27 mm)
Height (without feet): 5.56 in. (141.22 mm)
Height (with feet): 6.12 in. (155.45 mm)
Weight
(including lens):
Net: 32 lbs. (14.6 kg);
Shipping: 43.5 lbs. (19.8 kg)
Regulatory Approvals: Complies with FCC Class B, CE, C-Tick
Limited Warranty:
Projector: Two (2) years parts and labor from the date of
delivery to the end user.
Lamp Warranty: 1000 hours or six (6) months, whichever
comes first.
Specifications are subject to change without notice.
54
Runco CL-610 Owner’s Operating Manual
Dimensions
11.0 in. (279.4 mm)
16.5 in. (419.10 mm)
14.80 in. (376.0 mm)
8.86 in. (225.0 mm)
0.91 in. (23 mm)
2.36 in.
(60 mm)
8.07 in.
(205 mm) 12.57 in.
(319.15 mm)
16.31 in. (414.27 mm)
5.56 in. (141.22 mm)
2.66 in. (67.53 mm)
Runco CL-610 Owner’s Operating Manual
6.12 in. (155.45 mm)
55
SERIAL NUMBE R
RUMA-011115
rev 09-12-05
Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300
www.runco.com
Runco CL-610 Owner’s Operating Manual