Bosch GLL2-50 Operating/s Operating instructions

OBJ_BUCH-907-001.book Page 1 Tuesday, June 30, 2009 2:29 PM
P
-80 al
L 2 ion
GL fess
Pro
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
GLL 2-80 P Professional
www.bosch-pt.com
1 609 929 S04 (2009.06) T / 303 XXX
de
en
fr
es
pt
it
nl
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke
gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el Πρωτότυπο οδηγιών χρήσης
tr Orijinal işletme talimat
pl
cs
sk
hu
ru
Instrukcja oryginalna
Původní návod k používání
Pôvodný návod na použitie
Eredeti használati utasítás
Оригинальное руководство по
эксплуатации
uk Оригінальна інструкція з
експлуатації
ro Instrucţiuni originale
bg Оригинална инструкция
sr Originalno uputstvo za rad
sl Izvirna navodila
hr Originalne upute za rad
et Algupärane kasutusjuhend
lv
lt
cn
tw
ko
th
id
vi
Instrukcijas oriģinālvalodā
Originali instrukcija
正本使用说明书
正本使用說明書
사용 설명서 원본
หนังสือคู่มือการใช้งานฉบับต้นแบบ
Petunjuk-Petunjuk untuk
Penggunaan Orisinal
BΩng hõëng dÿn nguy›n bΩn
ar
ΔϴϠλϷ΍ ϞϴϐθΘϟ΍ ΕΎϤϴϠόΗ
fa
̶Ϡλ΍ έΎ̯ ίήσ ̵ΎϤϨϫ΍έ
OBJ_BUCH-907-001.book Page 3 Tuesday, June 30, 2009 2:32 PM
3|
2
3
4
5
6
1
1
P
-80 al
L 2 ion
GL fess
Pro
7
8
12
11
9
10
13
14
1
1
1 609 929 S04 | (30.6.09)
Bosch Power Tools
OBJ_BUCH-907-001.book Page 4 Tuesday, June 30, 2009 2:32 PM
4|
A
B
C
D
E
F
1 609 929 S04 | (30.6.09)
Bosch Power Tools
OBJ_BUCH-907-001.book Page 5 Tuesday, June 30, 2009 2:32 PM
5|
H
G
8
16
2 607 002 195
8
17
LR 2
0 601 069 100
15
1 608 M00 80K
19
Pro
iona
fess
18
l
BM 1
0 601 015 A00
BT 350
0 601 015 B00
1 608 M00 04U
20
2 607 990 031
21
BS 150
0 601 096 974
1 609 929 S04 | (30.6.09)
Bosch Power Tools
OBJ_BUCH-907-001.book Page 15 Tuesday, June 30, 2009 2:32 PM
English | 15
Safety Notes
en
Working safely with the measuring
tool is possible only when the
operating and safety information
are read completely and the instructions contained therein are
strictly followed. Never make warning labels
on the measuring tool unrecognisable. SAVE
THESE INSTRUCTIONS.
f Caution – The use of other operating or
adjusting equipment or the application of
other processing methods than those mentioned here, can lead to dangerous radiation exposure.
f The measuring tool is provided with a warning label in English (marked with number 13
in the representation of the measuring tool
on the graphics page).
f Do not operate the measuring tool in explosive environments, such as in the presence
of flammable liquids, gases or dusts. Sparks
can be created in the measuring tool which
may ignite the dust or fumes.
Keep the measuring tool and the
laser target plate 15 away from
cardiac pacemakers. The magnets of the measuring tool and
laser target plate generate a field
that can impair the function of
cardiac pacemakers.
f Keep the measuring tool and the laser target plate 15 away from magnetic data medium and magnetically-sensitive equipment.
The effect of the magnets of the measuring
tool and laser target plate can lead to irreversible data loss.
Functional Description
f Do not direct the laser beam at persons or
animals and do not stare into the laser
beam yourself. This measuring tool produces laser class 2 laser radiation according to
IEC 60825-1. This can lead to persons being
blinded.
f Do not use the laser viewing glasses as
safety goggles. The laser viewing glasses are
used for improved visualisation of the laser
beam, but they do not protect against laser
radiation.
f Do not use the laser viewing glasses as sun
glasses or in traffic. The laser viewing glasses do not afford complete UV protection and
reduce colour perception.
Please unfold the fold-out page with the representation of the measuring tool and leave it unfolded while reading the operating instructions.
Intended Use
The measuring tool is intended for determining
and checking horizontal and vertical lines.
Noise Information
The A-weighted sound pressure level of the audio signal at one meter distance is 80 dB(A).
Do not hold the measuring tool close to your
ear!
f Have the measuring tool repaired only
through qualified specialists using original
spare parts. This ensures that the safety of
the measuring tool is maintained.
f Do not allow children to use the laser measuring tool without supervision. They could
unintentionally blind other persons or themselves.
Bosch Power Tools
1 609 929 S04 | (30.6.09)
OBJ_BUCH-907-001.book Page 16 Tuesday, June 30, 2009 2:32 PM
16 | English
Technical Data
Line laser
GLL 2-80 P
Professional
Article number
3 601 K63 2..
Working range 1)
– Standard
– With pulse function
– With laser receiver
20 m
15 m
5–80 m
±0.2 mm/m
Levelling accuracy
Self-levelling range, typically
±4°
Levelling duration, typically
<4 s
Operating temperature
–10 °C ... +45 °C
Storage temperature
–20 °C ... +70 °C
90 %
Relative air humidity, max.
Laser class
2
Laser type
640 nm, <1 mW
1
C6
1/1600 s
Shortest pulse duration
1/4", 5/8"
Tripod mount
4 x 1.5 V LR6 (AA)
Batteries
Operating duration
– With 2 laser planes
– With 1 laser plane
9h
18 h
0.7 kg
Weight according to EPTA-Procedure 01/2003
159 x 141 x 54 mm
Dimensions
Degree of protection
IP 54 (dust and splash water protected)
1) The working range can be decreased by unfavourable environmental conditions (e.g. direct sun irradiation).
Please observe the article number on the type plate of your measuring tool. The trade names of the individual measuring tools may vary.
The measuring tool can be clearly identified with the serial number 14 on the type plate.
1 609 929 S04 | (30.6.09)
Bosch Power Tools
OBJ_BUCH-907-001.book Page 17 Tuesday, June 30, 2009 2:32 PM
English | 17
Product Features
The numbering of the product features shown
refers to the illustration of the measuring tool
on the graphic page.
1
2
3
4
Exit opening for laser beam
Battery low indicator
Pulse-function button
Operating mode button
5 Pulse-function indicator
6 Working without automatic levelling
indicator
7 On/Off switch
8 Magnets
9 Tripod mount 5/8"
10
11
12
13
14
15
16
17
18
19
20
21
Tripod mount 1/4"
Latch of battery lid
Battery lid
Laser warning label
Serial number
Laser target plate
Measurement plate with stand*
Laser receiver*
Protective pouch*
Universal holder*
Laser viewing glasses*
Tripod*
* The accessories illustrated or described are not
included as standard delivery.
Assembly
Inserting/Replacing the Battery
Alkali-manganese batteries are recommended
for the measuring tool.
To open the battery lid 12, slide the latch 11 in
the direction of the arrow and fold the battery
lid up. Insert the batteries. When inserting, pay
attention to the correct polarity according to the
representation on the inside of the battery lid.
When the batteries are weak when switching on
the measuring tool, the 5 s audio signal will
sound directly after switching on the measuring
tool.
Always replace all batteries at the same time.
Only use batteries from one brand and with the
identical capacity.
f Remove the batteries from the measuring
tool when not using it for extended periods.
When storing for extended periods, the batteries can corrode and discharge themselves.
Operation
Initial Operation
f Loud audio signals will sound under certain
conditions while operating the measuring
tool. Therefore, keep the measuring tool
away from your ear or other persons. The
loud audio signal can cause hearing damage.
f Protect the measuring tool against moisture and direct sun light.
f Do not subject the measuring tool to extreme temperatures or variations in temperature. As an example, do not leave it in
vehicles for longer periods. In case of large
variations in temperature, allow the measuring tool to adjust to the ambient temperature
before putting it into operation. In case of extreme temperatures or variations in temperature, the accuracy of the measuring tool can
be impaired.
f Avoid heavy impact or falling of the measuring tool. After heavy exterior impact on the
measuring tool, an accuracy check should always be carried out before continuing to
work (see “Levelling Accuracy”).
f Switch the measuring tool off during transport. When switching off, the levelling unit,
which can be damaged in case of intense
movement, is locked.
When the batteries become weak, a single 5 s
audio signal will sound. The battery low indicator 2 continuously flashes red. The measuring
tool can be operated for less then 2 h.
Bosch Power Tools
1 609 929 S04 | (30.6.09)
OBJ_BUCH-907-001.book Page 18 Tuesday, June 30, 2009 2:32 PM
18 | English
Switching On and Off
Deactivating the Signal Tone
To switch on the measuring tool, slide the
On/Off switch 7 to the “ on” position (when
working without automatic levelling) or to the
“
on” position (when working with automatic
levelling). Immediately after switching on, the
measuring tool sends laser beams out of the exit
openings 1.
After the measuring tool has been switched on,
the audio signal is always activated.
f Do not point the laser beam at persons or
animals and do not look into the laser beam
yourself, not even from a large distance.
To switch off the measuring tool, slide the
On/Off switch 7 to the “off” position. When
switching off, the levelling unit is locked.
When exceeding the maximum permitted operating temperature of 45 °C, the measuring tool
switches off to protect the laser diode. After
cooling down, the measuring tool is ready for
operation and can be switched on again.
Deactivating the Automatic Shut-off
When no button on the measuring tool is
pressed for approx. 30 minutes, the measuring
tool automatically switches off to save the batteries.
To switch on the measuring tool after automatic
shut-off, either slide the On/Off switch 7 to the
“off” position and then switch the measuring
tool on again or press the operating mode button 4 once or press the pulse-function button 3
once.
To deactivate the automatic shut-off, keep the
operating mode button 4 pressed for at least 3 s
(while the measuring tool is switched on). Deactivation of the automatic shut-off is confirmed
by brief flashing of the laser beams.
f Do not leave the switched on measuring
tool unattended and switch the measuring
tool off after use. Other persons could be
blinded by the laser beam.
To activate the automatic shut-off, switch the
measuring tool off and then on again or press
and hold the operating mode button 4 for at
least 3 s.
1 609 929 S04 | (30.6.09)
To deactivate/activate the audio signal, press
and hold the operating mode button 4 and the
pulse-function button 3 at the same time for at
least 3 s.
The audio signal activation and deactivation are
both confirmed by three short beeps.
Operating Modes
The measuring tool has three operating modes
between which you can switch at any time:
– Horizontal operation: generates a horizontal
laser plane,
– Vertical operation: generates a vertical laser
plane,
– Cross-line operation: generates a horizontal
and vertical laser plane.
After switching on, the measuring tool is in horizontal operation. Press the operating mode
button 4 to change the operating mode.
All three operating modes can be selected either
with or without automatic levelling.
Pulse Function
When working with the laser receiver 17, the
pulse function must be activated, – independent of the selected operating mode.
In pulse function, the laser lines flash at very
high frequency and thus become detectable by
the laser receiver 17.
To switch on the pulse function, press button 3.
When the pulse function is switched on, the
pulse-function indicator 5 lights up green.
When the pulse function is switched on, the visibility of the laser lines is reduced for the human
eye. Therefore, shut off the pulse function by
pushing button 3 again when working without
laser receiver. When the pulse function is
switched off, the pulse-function indicator 5 is
deactivated.
Bosch Power Tools
OBJ_BUCH-907-001.book Page 19 Tuesday, June 30, 2009 2:32 PM
English | 19
Automatic Levelling
Levelling Accuracy
Working with Automatic Levelling
Influences on Accuracy
Position the measuring tool on a level and firm
support, attach it to the holder 19 or to the tripod 21.
The ambient temperature has the greatest influence. Especially temperature differences occurring from the ground upward can divert the laser
beam.
When working with automatic levelling, push
the On/Off switch 7 to the “
on” position.
After switching on, the levelling function automatically compensates irregularities within the
self-levelling range of ±4°. The levelling is finished as soon as the laser beams do not move
any more.
Because the largest difference in temperature
layers is close to the ground, the measuring tool
should always be mounted on a tripod when
measuring distances exceeding 20 m. If possible, also set up the measuring tool in the centre
of the work area.
If automatic levelling is not possible, e.g. because the surface on which the measuring tool
stands deviates by more than 4° from the horizontal plane, the laser lines begin to flash rapidly. When the audio signal is activated, a fast-beat
signal sounds for 30 s (maximum). This alarm is
deactivated within 10 s after switching on, in order to allow adjustment of the measuring tool.
Apart from exterior influences, device-specific
influences (such as heavy impact or falling
down) can lead to deviations. Therefore, check
the accuracy of the measuring tool each time before starting your work.
Set up the measuring tool in level position and
wait for the self-levelling to take place. As soon
as the measuring tool is within the self-levelling
range of ±4°, all laser beams light up continuously and the audio signal is switched off.
Should the measuring tool exceed the maximum
deviation during one of the tests, please have it
repaired by a Bosch after-sales service.
Firstly, check the levelling accuracy of the horizontal laser line and then the levelling accuracy
of the vertical laser line.
In case of ground vibrations or position changes
during operation, the measuring tool is automatically levelled in again. To avoid errors, check
the position of the horizontal and vertical laser
line with regard to the reference points upon relevelling.
Working without Automatic Levelling
For working without automatic levelling, slide
the On/Off switch 7 to the “ on” position.
When automatic levelling is switched off, indicator 6 lights up red and for the first 30 s laser
beams flash slowly.
When the automatic levelling is switched off, the
measuring tool can be held by hand or placed on
an inclined surface. In cross-line operation, the
two laser lines do not necessarily run at a right
angle to each other.
Bosch Power Tools
1 609 929 S04 | (30.6.09)
OBJ_BUCH-907-001.book Page 20 Tuesday, June 30, 2009 2:32 PM
20 | English
Checking the Horizontal Levelling Accuracy of
the Lateral Axis
For this check, a free measuring distance of
5 metres on a firm surface between two walls A
and B is required.
– Without turning the measuring tool, position
it close to wall B. Switch the measuring tool
on and allow it to level in.
B
– Mount the measuring tool onto a tripod or
place it on a firm and level survace close to
wall A. Switch on the measuring tool. Select
cross-line operation with automatic levelling.
B
– Align the height of the measuring tool (using
a tripod or by underlaying, if required) in
such a manner that the cross point of the
laser lines is projected against the previously
marked point II on the wall B.
5m
– Direct the laser against the close wall A and
allow the measuring tool to level in. Mark the
centre of the point where the laser lines
cross each other on the wall (point I).
180˚
180˚
B
d
B
– Turn the measuring tool by 180°, allow it to
level in and mark the cross point of the laser
lines on the opposite wall B (point II).
– Without changing the height, turn around the
measuring tool by 180°. Direct it against the
wall A in such a manner that the vertical laser
line runs through the already marked point I.
Allow the measuring tool to level in and mark
the cross point of the laser lines on the wall
A (point III).
– The difference d of both marked points I and
III on wall A results in the actual height deviation of the measuring tool alongside the lateral axis.
On the measuring distance of 2 x 5 m = 10 m,
the maximum allowable deviation is:
10 m x ±0.2 mm/m = ±2 mm.
Thus, the difference d between points I and III
must not exceed 2 mm (max.).
1 609 929 S04 | (30.6.09)
Bosch Power Tools
OBJ_BUCH-907-001.book Page 21 Tuesday, June 30, 2009 2:32 PM
English | 21
Checking the Levelling Accuracy of the
Vertical Line
For this check, a door opening is required with
at least 2.5 metres of space (on a firm surface)
to each side of the door.
– Position the measuring tool on a firm, level
surface (not on a tripod) 2.5 m away from
the door opening. Allow the measuring tool
to level in while in vertical operation with automatic levelling, and direct the laser beam
at the door opening.
tool to level in and align the vertical laser line
in such a manner that its centre runs exactly
through points I and II.
– Mark the centre of the laser line at the upper
edge of the door opening as point IV.
– The difference d of both marked points III
and IV results in the actual deviation of the
measuring tool to the plumb line.
– Measure the height of the door opening.
The maximum admissible deviation is calculated
as follows:
Doubled height of the door opening x 0.2 mm/m
Example: For a door-opening height of 2 m, the
maximum deviation may be
2 x 2 m x ±0.2 mm/m = ±0.8 mm. Consequently,
points III and IV may be no more than 0.8 mm
(max.) apart from each other.
2
,5
m
2
,5
m
Working Advice
– Mark the centre of the vertical laser line at
the floor of the door opening (point I), at a
distance of 5 metres beyond the other side of
the door opening (point II) and at the upper
edge of the door opening (point III).
d
2m
– Rotate the measuring tool by 180° and position it on the other side of the door opening
directly behind point II. Allow the measuring
Bosch Power Tools
f Always use the centre of the laser line for
marking. The width of the laser line changes
with the distance.
Working with the laser target plate
The laser target plate 15 increases the visibility
of the laser beam under unfavourable conditions and at large distances.
The reflective part of the laser target plate 15
improves the visibility of the laser line. Thanks
to the transparent part, the laser line is also visible from the back side of the laser target plate.
Working with the Tripod (Accessory)
A tripod offers a stable, height-adjustable measuring support. Position the measuring tool with
the 1/4" tripod mount 10 onto the thread of the
tripod 21 or a commercially available camera tripod. For fastening to a commercially available
construction tripod, use the 5/8" tripod mount
9. Tighten the measuring tool with the tripod
mounting stud.
Fastening with the Universal Holder
(Accessory) (see figure D)
With the universal holder 19, you can fasten the
measuring tool, e.g., to vertical surfaces, pipes
or magnetizable materials. The universal holder
is also suitable for use as a ground tripod and
makes the height adjustment of the measuring
tool easier.
1 609 929 S04 | (30.6.09)
OBJ_BUCH-907-001.book Page 22 Tuesday, June 30, 2009 2:32 PM
22 | English
Working with the Measuring Plate (Accessory)
(see figures A–B)
Maintenance and Service
With the measuring plate 16, it is possible to
project the laser mark onto the floor or the laser
height onto a wall.
Maintenance and Cleaning
With the zero field and the scale, the offset or
drop to the required height can be measured
and projected at another location. This eliminates the necessity of precisely adjusting the
measuring tool to the height to be projected.
The measuring plate 16 has a reflective coating
that enhances the visibility of the laser beam at
greater distances or in intense sunlight. The
brightness intensification can be seen only
when viewing, parallel to the laser beam, onto
the measuring plate.
Working with the Laser Receiver (Accessory)
(see figure D)
Under unfavourable light conditions (bright environment, direct sunlight) and for larger distances, use the laser receiver for improved finding of the laser lines 17. When working with the
laser receiver, switch the pulse function on (see
“Pulse Function”, page 18).
Laser Viewing Glasses (Accessory)
The laser viewing glasses filter out the ambient
light. This makes the red light of the laser appear brighter for the eyes.
f Do not use the laser viewing glasses as
safety goggles. The laser viewing glasses are
used for improved visualisation of the laser
beam, but they do not protect against laser
radiation.
f Do not use the laser viewing glasses as sun
glasses or in traffic. The laser viewing glasses do not afford complete UV protection and
reduce colour perception.
Store and transport the measuring tool only in
the supplied protective pouch.
Keep the measuring tool clean at all times.
Do not immerse the measuring tool in water or
other fluids.
Wipe off debris using a moist and soft cloth. Do
not use any cleaning agents or solvents.
Regularly clean the surfaces at the exit opening
of the laser in particular, and pay attention to
any fluff of fibres.
If the measuring tool should fail despite the care
taken in manufacturing and testing procedures,
repair should be carried out by an authorised after-sales service centre for Bosch power tools.
Do not open the measuring tool yourself.
In all correspondence and spare parts orders,
please always include the 10-digit article
number given on the type plate of the measuring
tool.
In case of repairs, send in the measuring tool
packed in its protective pouch 18.
After-sales Service and Customer
Assistance
Our after-sales service responds to your questions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be
found under:
www.bosch-pt.com
Our customer service representatives can answer your questions concerning possible applications and adjustment of products and accessories.
Work Examples (see figures C–H)
Applicational examples for the measuring tool
can be found on the graphics pages.
1 609 929 S04 | (30.6.09)
Bosch Power Tools
OBJ_BUCH-907-001.book Page 23 Tuesday, June 30, 2009 2:32 PM
English | 23
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
E-Mail: bsctools@icon.co.za
Bosch Power Tools
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: +27 (031) 7 01 21 20
Fax: +27 (031) 7 01 24 46
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: +27 (021) 5 51 25 77
Fax: +27 (021) 5 51 32 23
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: +27 (011) 6 51 96 00
Fax: +27 (011) 6 51 98 80
E-Mail: rbsa-hq.pts@za.bosch.com
People’s Republic of China
Website: www.bosch-pt.com.cn
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 800 8 20 84 84
Tel.: +86 (571) 87 77 43 38
Fax: +86 (571) 87 77 45 02
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 (21) 02 02 35
Fax: +852 (25) 90 97 62
E-Mail: info@hk.bosch.com
www.bosch-pt.com.cn
Indonesia
PT. Multi Tehaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Indonesia
Tel.: +62 (21) 4 60 12 28
Fax: +62 (21) 46 82 68 23
E-Mail: sales@multitehaka.co.id
www.multitehaka.co.id
1 609 929 S04 | (30.6.09)
OBJ_BUCH-907-001.book Page 24 Tuesday, June 30, 2009 2:32 PM
24 | English
Philippines
Robert Bosch, Inc.
Zuellig Building
Sen. Gil Puyat Avenue
Makati City 1200, Metro Manila
Philippines
Tel.: +63 (2) 8 17 32 31
www.bosch.com.ph
Malaysia
Robert Bosch (SEA.) Pte. Ltd.
No. 8a, Jalan 13/6
46200 Petaling Jaya,
Selangor,
Malaysia
Tel.: +6 (03) 7966 3000
Fax: +6 (03) 7958 3838
E-Mail: hengsiang.yu@my.bosch.com
Toll Free Tel.: 1 800 880 188
Fax: +6 (03) 7958 3838
www.bosch.com.sg
Thailand
Robert Bosch Ltd.
Liberty Square Building
No. 287, 11 Floor
Silom Road, Bangrak
Bangkok 10500
Tel.: +66 (2) 6 31 18 79 – 18 88 (10 lines)
Fax: +66 (2) 2 38 47 83
Robert Bosch Ltd., P. O. Box 2054
Bangkok 10501, Thailand
Bosch Service – Training Centre
2869-2869/1 Soi Ban Kluay
Rama IV Road (near old Paknam Railway)
Prakanong District
10110 Bangkok
Thailand
Tel.: +66 (2) 6 71 78 00 – 4
Fax: +66 (2) 2 49 42 96
Fax: +66 (2) 2 49 52 99
Singapore
Robert Bosch (SEA.) Pte. Ltd.
38 C Jalan Pemimpin
Singapore 915701
Republic of Singapore
Tel.: +65 (3) 50 54 94
Fax: +65 (3) 50 53 27
www.bosch.com.sg
1 609 929 S04 | (30.6.09)
Vietnam
Robert Bosch (SEA) Pte. Ltd – Vietnam
Representative Office
Saigon Trade Center, Suite 1206
37 Ton Duc Thang Street,
Ben Nghe Ward, District 1
HCMC
Vietnam
Tel.: +84 (8) 9111 374 – 9111 375
Fax: +84 (8) 9111376
Disposal
Measuring tools, accessories and packaging
should be sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of measuring tools
into household waste!
According the European Guideline
2002/96/EC for Waste Electrical
and Electronic Equipment and its
implementation into national right, measuring
tools that are no longer usable must be collected separately and disposed of in an environmentally correct manner.
Battery packs/batteries:
Do not dispose of battery packs/batteries into
household waste, fire or water. Battery packs/
batteries should be collected, recycled or disposed of in an environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries
must be recycled according the guideline
91/157/EEC.
Battery packs/batteries no longer suitable for
use can be directly returned at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Subject to change without notice.
Bosch Power Tools