American DJ MEGA TRI38 SYSTEM User manual

MEGA TRI38 SYSTEM
MEGA TRI38 SYSTEM
Introduction
Unpacking: Thank you for purchasing the MEGA TRI38 SYSTEM by
ADJ Products, LLC. Every MEGA TRI38 SYSTEM has been thoroughly
tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your
fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found
or parts are missing, please contact our toll free customer support
number for further instructions. Do not return this unit to your dealer
without first contacting customer support.
Introduction: The ADJ MEGA TRI38 SYSTEM is part of a continuing pursuit to create high quality intelligent lighting. The MEGA TRI38
SYSTEM is an exciting all-in-one DMX intelligent LED par system. This
lighting system features four RGB color mixing LED fixtures. This fixture can be used in a stand alone mode or connected in a Master/Slave
configuration. This system has five operating modes: Sound Active
mode, Auto mode, Built-In Program mode, RGB dimmer mode, and
DMX control mode.
Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacific Standard Time.
Voice:
(323) 582-3322
Fax: (323) 582-3108
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
User Instructions
Rev. 6/13
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 2
MEGA TRI38 SYSTEM
General Instructions
To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations
of this unit. These instructions contain important safety information
regarding the use and maintenance of this unit. Please keep this manual
with the unit, for future reference.
MEGA TRI38 SYSTEM
Features
•
•
•
•
•
•
•
•
•
•
Mulit-Colors
Six Operating Modes
12 Built-In Programs
32 Color Macros
Electronic Dimming 0-100%
Built in Microphone
DMX-512 protocol
3-Pin DMX Connection
Wireless RF/Battery Powered Foot Controller
3 DMX Modes: 6 Channel Mode, 12 Channel Mode, and 15 Channel Mode
• ADJ LED RC compatiable (Not Included)
MEGA TRI38 SYSTEM
Warranty Registration
The MEGA TRI38 SYSTEM carries a 3 year limited warranty. Please fill
out the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 3
MEGA TRI38 SYSTEM
Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 16 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 4
MEGA TRI38 SYSTEM
Set Up
MEGA TRI38 SYSTEM
Power Supply: The ADJ MEGA TRI38 SYSTEM contains a automatic
voltage switch, which will auto sense the voltage when it is plugged
into a power source. With this switch there is no need to worry about
the correct power voltage, this unit can be plugged in anywhere.
cables. Do not DMX+,DMX-,COMMON
use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does
not influence the
DMX512
DMX+,DMX-,COMMON
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
SOUND
INPUT
OUTPUT
COMMON
REMOTE
CONTROL
INPUT
1 Ground
2
3
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 5
2
OUTPUT
3
DMX -
1
2
SOUND
XLR Female Socket
2 Cold
2 Cold
1 Ground
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
INPUT
3
1
2
Figure 2
OUTPUT
Termination redu
avoids signal tra
and interference.
to connect a DMX
120 Ohm 1/4 W)
and PIN 3 (DMX
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
Figure 3
3 Hot
Pin 3 = Data True (positive)
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
COMMON
XLR
DMX -The
The MEGA TRI38 SYSTEM can be controlled via3-PIN
DMX-512
protocol.
MEGA TRI38 SYSTEM has 3 DMX channel modes, please see pages 8-9
for the different modes. The DMX address is set on the back panel of the
MEGA TRI38 SYSTEM. Your unit and your DMX
controller require a standard 3-pin XLR connector for data input and data output (Figure 1). We
recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all pro lighting stores). Your
cables should be made with a male and female
XLR connector on either end of the cable. Also
Figure 1
remember that DMX cable must be daisy chained
and cannot be split.
INPUT
DMX +
3
XLR Male Socket
POWER
1
1
DMX512 OUT
3-PIN XLR
SOUND
Data Cable (DMX Cable) Requirements DMX512
(ForOUT
DMX Operation):
DMX +
POWER
Notice: Be sure to DMX512
follow figures two and three when making your own
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
REMOTE
CONTROL
INPUT
Set Up
POWER
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 6
MEGA TRI38 SYSTEM
Operating Instructions
LED Display On/Off: To make the display stay ON all of the time
press the MODE and UP buttons at the same time. To make the display turn OFF after 20 seconds, press the MODE and DOWN buttons
at the same time.
Operating Modes:
The MEGA TRI38 SYSTEM has six operating modes:
• RGB Dimmer Mode - Choose one of the three colors to remain stat-
ic or adjust the intensity of each color to make your desired color.
• Built-In Program - There are 12 built-in programs to choose from.
• Static Color Mode - There are 32 colors to choose from.
• Auto Mode - This will run a automatic program.
• Sound-Active mode - The unit will react to sound, chasing through the
built in programs.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the ADJ Show Designer™.
RGB Dimmer Mode:
1. Plug the fixture in and press the MODE button until:
2. When “r.XXX” is displayed you are in Red dimming mode. Press the UP and DOWN buttons to adjust intensity.
3. When “G.XXX” is displayed you are in Green dimming mode. Press the UP and DOWN buttons to adjust intensity.
4. When “b.XXX” is displayed you are in Blue dimming mode. Press the UP and DOWN buttons to adjust intensity.
5. After you have adjusted the RGB colors to make your desired color you can then activate strobing by pressing the SET UP button to enter the Flash (strobe) mode.
6. “FS.XX” will be displayed, this is Flash mode. The Flash can be
adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).
Built-In Program Mode:
1. Plug the fixture in and press the MODE button until “Pr.XX” is displayed. “XX” represents a number from 1-12. Use the UP or DOWN buttons to scroll through the 12 programs. Once you have found your desired program press the SET UP button.
2. Pressing the SET UP button will display “SP.XX”. When this is dis-
played you can adjust the running speed of your desired program. Use the UP or DOWN button to adjust the speed between “SP.01” ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 7
MEGA TRI38 SYSTEM
Operating Instructions
(slowest) and “SP.99” (fastest). Once you have set your desired run-
ning speed, you can press the SET UP button to to enter the Flash (Strobe) mode.
3. After pressing SET UP, “FS.XX” will be displayed, this is Flash mode. The Flash can be adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).
Static Color Mode:
In this mode the MEGA TRI38 SYSTEM you can select one of 32 custom
colors to remain static.
1. Plug the fixture in and press the MODE button until “Pr.XX” is dis-
played. “XX” represents the program number that is displayed.
2. Use the UP or DOWN buttons to scroll to Program 1 (Pr.01).
3. Press the SET UP button, “CL.XX” will be displayed, this is Static Color mode. Use the UP or DOWN button to find your desired color.
Auto Run Mode:
1. Plug the fixture in and press the MODE button until “AUTO”, is dis-
played.
2. Press the SET UP button so that “SP.XX” is displayed. When this is displayed you can adjust the running speed of your desired program. Use the UP or DOWN button to adjust the speed between “SP.01” (slowest) and “SP.99” (fastest). Once you have set your desired run-
ning speed, you can press the SET UP button to to enter the Flash (Strobe) mode.
3. After pressing SET UP, “FS.XX” will be displayed, this is Flash mode. The Flash can be adjusted between “FS.00” (flash off) to “FS.99” (fastest flash).
Sound Active Mode:
In this mode the MEGA TRI38 SYSTEM will react to sound, and chase
through the different colors.
1. Plug the fixture in and press the MODE button until “SU.XX” is dis-
played. “XX” represents the sound sensitivity setting (0-31) currently displayed. Use the UP or DOWN buttons to adjust the
sensitivity. “SU.01” is the least sensitive, “SU.31” is the most.
2. The fixture will now change via sound.
DMX Mode:
Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs. This funcADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 8
MEGA TRI38 SYSTEM
Operating Instructions
tion also allows you to use your fixtures as spot lights. The MEGA TRI38
SYSTEM has 3 DMX modes: 6 Channel mode, 12 Channel mode, and a
15 Channel mode. See pages 12-15 for each modes’ DMX traits.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until “d-P.X” is displayed. “X” represents the current displayed DMX chan-
nel mode. Use the UP or DOWN buttons to select your desired
DMX channel mode. See the next page for the DMX Channel Modes.
3. Once you have chosen your desired DMX Channel mode press the SETUP button to set your DMX address. Use the UP or DOWN but-
tons to adjust the DMX address.
DMX Channel modes:
• To run the 6 Channel Mode, press the MODE button until “d-P.X” is displayed. Press the UP or DOWN buttons until “d-P.1” is dis-
played. This is the 6 Channel DMX Mode.
• To run the 12 Channel Mode, press the MODE button until “d-P.X” is displayed. Press the UP or DOWN buttons until “d-P.2” is dis-
played. This is the 12 Channel DMX Mode.
• To run the 15 Channel Mode, press the MODE button until “d-P.X” is displayed. Press the UP or DOWN buttons until “d-P.3” is dis-
played. This is the 15 Channel DMX Mode.
4. Please see pages 12-15 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode and address plug in the fixture via the XLR connections to any standard DMX controller.
ADJ RC4 (Remote Control) On/Off:
MEGA TRI38 SYSTEM
Master-Slave Configuration
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data cables to link your units together. Remember
that the Male XLR connector is the input and the Female XLR con-
nector is the ouput. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.
2. Set the “Master” system to your desired mode of operation.
3. On the “Slave” system, press the MODE button until “Slav” is dis-
played. Once “Slav” is displayed connect the “Slave” system to the “Master.” The “Slave” system will now follow the “Master”.
MEGA TRI38 SYSTEM
Foot Controller
The wireless foot controller has 4 different functions. To activate the
foot controller press any pedal once.
BLACKOUT - Pressing this pedal will blackout the fixture.
SOUND - This pedal activates sound active mode.
PROGRAM - This pedal will activate program mode and cycle
through programs 2-12 with each press of the pedal.
This function is used to activate and deactivate the ADJ RC4 (Remote
Control). When this function is activated you can control the fixture
using the ADJ RC4. Please see page 11 for controls and functions.
1. Plug the fixture in and press the MODE button until “AUTO” is dis- played.
2. Press the SET UP button until “Ir.XX” is displayed. “XX” represents either “on” or “oF”.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
COLOR - This pedal activates color macro mode and each press of
this pedal switches to the next color. There are 32 colors to choose
from.
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 9
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 10
MEGA TRI38 SYSTEM
ADJ RC4 Operation
The ADJ RC4 remote (sold seperately) has many different functions and
allows you to control your MEGA TRI38 SYSTEM from long distance. The
ADJ RC4 remote can control your system up to 150 ft. To use the remote you must first activate the fixtures receiver, to activate the receiver
please see the instructions on page 9.
BLACKOUT - Pressing this button will blackout the fixture.
SOUND - This button activates sound active mode.
MEGA TRI38 SYSTEM
Channel
1
2
3
PROGRAM - This button will activate program mode and cycle
through programs 2-12 with each press of the button.
COLOR - This button activates color macro mode and each press of
this button switches to the next color. There are 32 colors to choose
from.
4
5
6
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
1 - 255
0 - 255
0 - 16
17 - 33
34 - 50
51 - 67
68 - 84
85 - 101
102 - 118
119 - 135
136 - 152
153 - 169
170 - 186
187 - 203
204 - 220
221 - 237
238 - 255
0 - 255
6 Channel DMX Mode
Function
RED (Par 1-4)
0% - 100%
GREEN (Par 1-4)
0% - 100%
BLUE (Par 1-4)
0% - 100%
COLOR MACROS
(See page 18 for colors & values)
PROGRAM SPEED SLOW - FAST
STROBE/SOUND SENSITIVITY
STROBING SLOW - FAST
SOUND SENSITIVITY LEAST - MOST
PROGRAMS
NO FUNCTION
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
PROGRAM 5
PROGRAM 6
PROGRAM 7
PROGRAM 8
PROGRAM 9
PROGRAM 10
PROGRAM 11
PROGRAM 12
AUTO RUN
SOUND ACTIVE
MASTER DIMMER
0% - 100%
• When Channels 1, 2, and 3 are being used, Channel 4 will control strobing.
• Channels 1, 2, and 3 will not work, when Channel 5 is being used.
• When Channel 5 is using Program 1, Channel 3 will control the Color Macros, and Channel 4 will control strobing.
• When Channel 5 is being used (values 34-237), Channel 3 will control the program speed.
• When Channel 5 is in Sound Active mode ( values 238-255), Channel 4 will control sound sensitivity.
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 11
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 12
MEGA TRI38 SYSTEM
Channel
1
2
3
4
5
6
7
8
9
10
11
12
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
12 Channel DMX Mode
Function
RED (PAR 1)
0% - 100%
GREEN (PAR 1)
0% - 100%
BLUE (PAR 1)
0% - 100%
RED (PAR 2)
0% - 100%
GREEN (PAR 2)
0% - 100%
BLUE (PAR 2)
0% - 100%
RED (PAR 3)
0% - 100%
GREEN (PAR 3)
0% - 100%
BLUE (PAR 3)
0% - 100%
RED (PAR 4)
0% - 100%
GREEN (PAR 4)
0% - 100%
BLUE (PAR 4)
0% - 100%
MEGA TRI38 SYSTEM
Channel
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 13
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
1 - 255
0 - 255
0 - 16
17 - 33
34 - 50
15 Channel DMX Mode
Function
RED (PAR 1)
0% - 100%
GREEN (PAR 1)
0% - 100%
BLUE (PAR 1)
0% - 100%
RED (PAR 2)
0% - 100%
GREEN (PAR 2)
0% - 100%
BLUE (PAR 2)
0% - 100%
RED (PAR 3)
0% - 100%
GREEN (PAR 3)
0% - 100%
BLUE (PAR 3)
0% - 100%
RED (PAR 4)
0% - 100%
GREEN (PAR 4)
0% - 100%
BLUE (PAR 4)
0% - 100%
COLOR MACROS
(See page 18 for colors & values)
PROGRAM SPEED SLOW - FAST
STROBE/SOUND SENSITIVITY
STROBING SLOW - FAST
SOUND SENSITIVITY LEAST - MOST
PROGRAMS
NO FUNCTION
PROGRAM 1
PROGRAM 2
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 14
MEGA TRI38 SYSTEM
Channel
14
15
Value
51 - 67
68 - 84
85 - 101
102 - 118
119 - 135
136 - 152
153 - 169
170 - 186
187 - 203
204 - 220
221 - 237
238 - 255
0 - 255
15 Channel DMX Mode
Function
PROGRAMS
PROGRAM 3
PROGRAM 4
PROGRAM 5
PROGRAM 6
PROGRAM 7
PROGRAM 8
PROGRAM 9
PROGRAM 10
PROGRAM 11
PROGRAM 12
AUTO RUN
SOUND ACTIVE
MASTER DIMMER
0% - 100%
• When Channels 1-12 are being used, Channel 13 will control strobing.
• Channels 1-12 will not work, when Channel 14 is being used.
• When Channel 14 is using Program 1 (values 17-33), Channel 12 will
control the Color Macros, and Channel 13 will control strobing.
• When Channel 14 is being used (values 34-237), Channel 12 will control the program speed.
• When Channel 14 is in Sound Active mode ( values 238-255), Channel 13 will control sound sensitivity.
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 15
MEGA TRI38 SYSTEM
Color Macro Chart
Value
Color
1-7
8 - 15
16 - 23
24 - 31
32 - 39
40 - 47
48 - 55
56 - 63
64 - 71
72 - 79
80 - 87
88 - 95
96 - 103
104 - 111
112 - 119
120 - 127
128 - 135
136 - 143
144 - 151
152 - 159
160 - 167
168 - 175
176 - 183
184 - 191
192 - 199
200 - 207
208 - 215
216 - 223
224 - 231
232 - 239
240 - 247
248 - 255
BASTARD AMBER
MEDIUM AMBER
PALE AMBER GOLD
GALLO GOLD
GOLDEN AMBER
LIGHT RED
MEDIUM RED
MEDIUM PINK
BROADWAY PINK
FOLLIES PINK
LIGHT LAVENDER
SPECIAL LAVENDER
LAVENDER
INDIGO
HEMSLEY BLUE
TIPTON BLUE
LIGHT STEEL BLUE
LIGHT SKY BLUE
SKY BLUE
BRILLIANT BLUE
LIGHT GREEN BLUE
BRIGHT BLUE
PRIMARY BLUE
CONGO BLUE
PALE YELLOW GREEN
MOSS GREEN
PRIMARY GREEN
DOUBLE CTB
FULL CTB
HALF CTB
DARK BLUE
WHITE
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 16
MEGA TRI38 SYSTEM
Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that the
fuse holder is located inside the power socket. Insert a flat-head screw
driver into the power socket and gently pry out the fuse holder. Remove
the bad fuse and replace with a new one. The fuse holder also has a
holder for a spare fuse.
MEGA TRI38 SYSTEM
Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
MEGA TRI38 SYSTEM
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 17
MEGA TRI38 SYSTEM
Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the
product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon it’s products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published. This warranty was revised after December 1, 2012.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
• Laser Products = 90-Day Limited Warranty
• L.E.D. Products = 3-year (1095 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 18
MEGA TRI38 SYSTEM
Model: MEGA TRI38 SYSTEM
Specifications
Voltage: 100V~240V 50/60Hz
LEDs:
12 x 3 Watt TRI Color LEDs
Beam Angle:
25 Degree
Working Position: Any safe working position
Power Draw:
45W Max. (Entire System)
Fuse:
1 Amp
Weight: 21lbs./ 9.5Kgs.
Dimensions: 34.75” (L) x 10” (W) x 2.5” (H)
877 x 252 x 60mm
Colors:
RGB Color Mixing
DMX Channels:
3 DMX Modes: 6 Channel Mode, 12 Channel Mode, & 15 Channel
Mode
Warranty:
3 Year (1,095 days)
Foot Controller
Weight:
Dimensions:
3lbs./ 1.4 Kgs
15.7” (L) x 5.5” (W) x 1.9” (H)
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which
will auto sense the voltage when it is plugged into the power source.
Please Note: Specifications and improvements in the design of this unit and
this manual are subject to change without any prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@adj.com
ADJ Products, LLC - www.adj.com - MEGA TRI38 SYSTEM User Manual Page 19
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
www.adj.com
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99