ADTRAN NetVanta 4305 Installation guide

NetVanta 4305
Hardware Installation Guide
1200890L1
NetVanta 4305 Chassis
1200861L1
NetVanta 56K/64K Network Interface Module
1200862L1
NetVanta T1/FT1 Network Interface Module
1200863L1
NetVanta T1/FT1+DSX-1 Network Interface Module
1200866L1
NetVanta Serial Network Interface Module
1200868L1
NetVanta E1/FE1 Network Interface Module
1200872L1
NetVanta Dual T1 Network Interface Module
1200864L1
NetVanta Analog Modem Dial Backup Interface Module
1200865L1
NetVanta ISDN BRI Dial Backup Interface Module
1200875L1
NetVanta ISDN S/T Dial Backup Interface Module
1200878L1
NetVanta E1/FE1 w/ G.703 Drop Network Interface Module
4202368L2
Enhanced Feature Pack (VPN Upgrade)
1202862L1
NetVanta T1/FT1 Network Interface Module 2nd, Gen
1202863L1
NetVanta T1/FT1+DSX-1 Network Interface Module, 2nd Gen
1200843L1
NetVanta Octal T1/E1 Wide Module
61200890L1-34B
July 2004
Trademarks
NetVanta 4305 Hardware Installation Guide
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: (256) 963-8000
© 2004 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
2
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Conventions
Conventions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the equipment or
endangerment to human life.
61200890L1-34B
© 2004 ADTRAN, Inc.
3
Safety Instructions
NetVanta 4305 Hardware Installation Guide
Safety Instructions
When using your telephone equipment, please follow these basic safety precautions to reduce the risk of
fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for special disposal instructions.
5. The socket-outlet shall be installed near the equipment and shall be easily accessible.
This equipment incorporates double pole/neutral fusing. If the neutral fuse opens and line
fuse does not open, voltage could still be present in the unit.
Save These Important Safety Instructions
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
4
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
FCC-Required Information
FCC-Required Information
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. Each
registered interface has a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could effect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty
information. The telephone company may require this equipment to be disconnected from the
network until the problem is corrected or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. This equipment is designed to connect to the telephone network or premises wiring using an FCCcompatible modular jack, which is compliant with Part 68 and requirements adopted by ACTA.
7. The following information may be required when applying to the local telephone company for
leased line facilities:
Part Number
1200861L1
1200862L1
1200863L1
1202862L1
1202863L1
Registration
Number
US:HDCDENAN1200861L1
US: HDCDENAN1200863L1
US: HDCDENAN1202863L1
Service Type
REN/SOC
FIC
USOC
56 Kbps Digital Interface
64 Kbps Digital Interface
6.0F
04DU5-56
04DU5-64
RJ-48S
1.544 Mbps - SF
1.544 Mbps - SF and B8ZS
1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS
6.0N
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
RJ-48C
1200872L1
US: HDCDENAN1200872L1
1200864L1
US: HDCM504A1200864L1
Analog Loop Start
0.4A/9.0F
02LS2
RJ-11C
1200865L1
US: HDCDENAN1200865L1
Basic Rate ISDN
6.0F
021S5
RJ-49C
8. The REN is useful in determining the quantity of devices you may connect to your telephone line
and still have all of those devices ring when your number is called. In most areas, the sum of the
RENs of all devices should not exceed five. To be certain of the number of devices you may
connect to your line as determined by the REN, call your telephone company to determine the
maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
10.
61200890L1-34B
© 2004 ADTRAN, Inc.
5
FCC Radio Frequency Interference Statement
NetVanta 4305 Hardware Installation Guide
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Electromagnetic Compatibility (EMC) Table
NetVanta Module P/N and Name
NetVanta 4305 (1200890L1)
1200861L1
56K/64K NIM
FCC Part 15, Class A
EN55022 Class A
1200862L1
T1/FT1 NIM
FCC Part 15, Class A
EN55022 Class A
1202862L1
T1/FT1 NIM, 2nd Gen
FCC Part 15, Class A
EN55022 Class A
1200863L1
T1/FT1+DSX-1 NIM
FCC Part 15, Class A
EN55022 Class A
1202863L1
T1/FT1+DSX-1 NIM, 2nd Gen
FCC Part 15, Class A
EN55022 Class A
1200866L1
Serial NIM
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200843L1
Octal T1/E1 Wide Module
FCC Part 15, Class A
EN55022 Class A
1200864L1
Analog Modem DIM
FCC Part 15, Class A
EN55022 Class A
1200865L1
1200875L1
ISDN BRI DIM
ISDN S/T DIM
FCC Part 15, Class A
EN55022 Class A
1200868L1
1200872L1
E1/FE1 NIM
Dual T1 NIM
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200878L1
E1/FE1 w/ G.703 Drop
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1202368L1
VPN Encryption (Accelerator) Card
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
6
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Industry Canada Compliance Information
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the “IC:” in front
of the certification/registration number) signifies that the Industry Canada technical specifications were met.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the documentation or on
the product labeling/markings. The REN assigned to each terminal device indicates the maximum number of
terminals that can be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the RENs of all the devices should not exceed
five (5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in
the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of
Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques de Class
A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee par le ministre des
Communications.
61200890L1-34B
© 2004 ADTRAN, Inc.
7
Affidavits
NetVanta 4305 Hardware Installation Guide
Affidavits
Affidavit Requirements for Connection to Digital Services
•
An affidavit is required to be given to the telephone company whenever digital terminal equipment without
encoded analog content and billing protection is used to transmit digital signals containing encoded analog content
which are intended for eventual conversion into voiceband analog signals and transmitted on the network.
•
The affidavit shall affirm that either no encoded analog content or billing information is being transmitted or that
the output of the device meets Part 68 encoded analog content or billing protection specifications.
•
End user/customer will be responsible for filing an affidavit with the local exchange carrier when connecting
unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital services.
•
Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit requirement
for subrate services is waived.
8
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Affidavits
Affidavit for Connection Of Customer Premises Equipment to 1.544 Mbps And/or Subrate Digital
Services
For the work to be performed in the certified territory of ___________________(telco name)
State of ________________
County of ________________
I, _______________________ (name), _____________________________(business address),
____________________ (telephone number) being duly sworn, state:
I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or ________ subrate
digital services. The terminal equipment to be connected complies with Part 68 of the FCC rules except for the encoded analog content and
billing protection specifications. With respect to encoded analog content and billing protection:
( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with respect to analog content and
encoded billing protection information continuously complies with Part 68 of the FCC Rules and Regulations.
( ) The digital CPE does not transmit digital signals containing encoded analog content or billing information which is intended to be decoded
within the telecommunications network.
( ) The encoded analog content and billing protection is factory set and is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and adjustment of the
encoded analog content and billing information has (have) been trained to perform these functions by successfully having completed one
of the following (check appropriate blocks):
( ) A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or
( ) A training course provided by the customer or authorized representative, using training materials and instructions provided by the
manufacturer/grantee of the equipment used to encode analog signals; or
( ) An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the equipment used to
encode analog signals; or
( ) In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the control of a supervisor trained in accordance with
_________ (circle one) above.
I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the information as
provided in the preceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of _______________, _______
_________________________________
Notary Public
My commission expires:
_________________________________
61200890L1-34B
© 2004 ADTRAN, Inc.
9
Warranty and Customer Service
NetVanta 4305 Hardware Installation Guide
Warranty and Customer Service
ADTRAN will repair and return this product within the warranty period if it does not meet its published
specifications or fails while in service. Warranty information can be found at: http://support.adtran.com
(Click on Warranty and Repair Information, under Support.)
Product Registration
Registering your product helps ensure complete customer satisfaction. Please take time to register your
products on line at http://support.adtran.com. Click on Service/Support and then on Product Registration
under Support.
Product Support Information
A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,
RMA requests, training, or more information, use the following contact information:.
Repair and Return
If you determine that a repair is needed, please contact our Customer and Product Service (CaPS)
department to have an RMA number issued. CaPS should also be contacted to obtain information
regarding equipment currently in house or possible fees associated with repair.
CaPS Department
(256) 963-8722
Identify the RMA number clearly on the package (below address), and return to the following address:
ADTRAN Customer and Product Service
901 Explorer Blvd. (East Tower)
Huntsville, Alabama 35806
RMA # _____________
10
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Product Support Information
Pre-Sales Inquiries and Applications Support
Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,
the ADTRAN Support web site provides a variety of support services such as a searchable knowledge
base, latest product documentation, application briefs, case studies, and a link to submit a question to an
Applications Engineer. All of this, and more, is available at:
http://support.adtran.com
When needed, further pre-sales assistance is available by calling our Applications Engineering
Department.
Applications Engineering (800) 615-1176
Post-Sale Support
Your reseller should serve as the first point of contact for support. If additional support is needed, the
ADTRAN Support web site provides a variety of support services such as a searchable knowledge base,
updated firmware releases, latest product documentation, service request ticket generation and troubleshooting tools. All of this, and more, is available at:
http://support.adtran.com
When needed, further post-sales assistance is available by calling our Technical Support Center. Please
have your unit serial number available when you call.
Technical Support
(888) 4ADTRAN
International Technical Support
1-256-963-8716
Installation and Maintenance Support
The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation
and maintenance services which allow you to choose the kind of assistance you need. This support is
available at:
http://support.adtran.com
For questions, call the ACES Help Desk.
ACES Help Desk
61200890L1-34B
(888) 874-ACES (2237)
© 2004 ADTRAN, Inc.
11
Product Support Information
NetVanta 4305 Hardware Installation Guide
Training
The Enterprise Network (EN) Technical Training Department offers training on our most popular products.
These courses include overviews on product features and functions while covering applications of
ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training
and courses taught at our facilities or at your site. For more information about training, please contact your
Territory Manager or the Enterprise Training Coordinator.
12
Training Phone
(800) 615-1176, ext. 7500
Training Fax
(256) 963-6700
Training Email
training@adtran.com
© 2004 ADTRAN, Inc.
61200890L1-34B
Table of Contents
Introduction to the NetVanta 4305 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpack and Inspect the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents of ADTRAN Shipments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
20
20
Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reviewing the Base Unit Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reviewing the Rear Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel Interfaces and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
23
23
25
25
Option Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta 56K/64K NIM (P/N 1200861L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta T1/FT1 NIM (P/N 1200862L1 or P/N 1202862L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta T1/FT1+DSX-1 NIM (P/N 1200863L1 or P/N 1202863L1) . . . . . . . . . . . . . . . . . . . . .
NetVanta Dual T1 NIM (P/N 1200872L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta Serial NIM (P/N 1200866L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta E1/FE1 NIM (P/N 1200868L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta E1/FE1 with G.703 Drop NIM (P/N 1200878L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta Octal T1 Wide NIM (P/N 1200843L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dial Backup Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta Analog Modem DIM (P/N 1200864L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta ISDN BRI DIM (P/N 1200865L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta ISDN S/T DIM (P/N 1200875L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
27
27
28
29
30
31
32
33
34
35
35
36
37
Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rack Mounting NetVanta 4305. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplying Power to the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta 4305 (AC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Dial Backup and Network Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the NetVanta VPN Accelerator Card (1202368L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
38
39
39
40
40
41
43
Appendix A. Connector Pin Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
61200890L1-34B
© 2004 ADTRAN, Inc.
13
Table of Contents
14
NetVanta 4305 Hardware Installation Guide
© 2004 ADTRAN, Inc.
61200890L1-34B
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
NetVanta 4305 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta 4305 Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta 56K/64K NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta T1/FT1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta T1/FT1+DSX-1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta Dual T1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta Serial NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta E1/FE1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta E1/FE1 with G.703 Drop NIM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetVanta Octal T1 Wide NIM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing DIMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NIM and DIM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VPN Card Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61200890L1-34B
© 2004 ADTRAN, Inc.
23
25
27
28
29
30
31
32
33
34
41
42
43
15
List of Figures
16
NetVanta 4305 Hardware Installation Guide
© 2004 ADTRAN, Inc.
61200890L1-34B
List of Tables
Table 1.
Table A-1.
Table A-2.
Table A-3.
Table A-4.
Table A-5.
Table A-6.
Table A-7.
Table A-8.
Table A-9.
Table A-10.
61200890L1-34B
NetVanta 4305 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10/100BaseT Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Port (DCE) Pinout for NetVanta 4305 (p/n 1200890L1) . . . . . . . . . . . . . . . . . . . .
WAN-DDS Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WAN-T1 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WAN-E1 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSX-1 Connector Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G.703 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial NIM Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DBU Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DBU Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
© 2004 ADTRAN, Inc.
23
45
45
46
46
46
47
47
48
49
49
17
List of Tables
18
NetVanta 4305 Hardware Installation Guide
© 2004 ADTRAN, Inc.
61200890L1-34B
1.
INTRODUCTION TO THE NETVANTA 4305
The NetVanta 4305 is a mid-range IP router designed for medium-to-large office connectivity over Frame
Relay or point-to-point (PPP) networks. This modular platform offers a complete solution for access
routing and WAN connectivity in a single, compact package.
The main base unit supports a variety of interchangeable network interface modules (NIMs) and dial
backup interface modules (DIMs).
The NetVanta 4305 base unit includes the following:
•
•
•
1U high housing, rack-mountable, metal enclosure
Three modular (card) slots (two small, one wide)
Two built-in Ethernet ports
The NIMs available in this series provide a variety of WAN connectivity options including the following:
• 56K/64K (DDS)
• T1/FT1
• T1/FT1 with DSX-1
• E1/FE1
• Dual T1
• E1/FE1 with G.703 Drop
• Serial (V.35/X.21)
If needed, an analog modem, ISDN BRI (U Interface) DIM, or ISDN S/T DIM can plug onto the NIM,
providing dial backup capability. Refer to Installing Dial Backup and Network Interface Modules on
page 41 for more details.
For VPN applications using the NetVanta 4305, the optional VPN Accelerator Card provides encryption /
decryption and security acceleration services. Refer to Installing the NetVanta VPN Accelerator Card
(1202368L1) on page 43.
Features and Specifications
The NetVanta 4305 has the following features:
•
•
•
•
•
•
•
•
•
Modular network interface: 56K/64K, T1/FT1, T1/FT1+DSX-1, E1/FE1, Dual T1,
E1/FE1+G.703 Drop, or Serial interface
1U high metal chassis with three slots for option modules
Two integrated 10/100BaseT Ethernet ports (RJ-48C)
WAN Protocol: Frame Relay or PPP
Integrated IP router with bridging
RIP Versions 1 and 2, and OSPF routing protocols
IP encapsulation over Frame Relay (RFC 1490)
ADTRAN Operating System Command Line Interface (CLI)
SNMP management
61200890L1-34B
© 2004 ADTRAN, Inc.
19
Introduction to the NetVanta 4305
NetVanta 4305 Hardware Installation Guide
• Integrated EIA-232 DCE configuration port (DB-9)
• Optional dial backup (ISDN BRI DIM, ISDN S/T DIM, or analog modem)
• Optional VPN Accelerator Card provides encryption/decryption and security acceleration services
• Front panel LEDs
• Dimensions: 17.22”W x 1.72”H x 10.990”D
• Mountable in a 19” rack
• Worldwide auto-ranging AC power supply
This hardware installation guide describes the NetVanta 4305, details basic functionality, gives installation
instructions, and lists hardware specifications. For more information on router configuration for a specific
application, refer to the quick start documents provided on your ADTRAN OS Documentation CD. For
details on the command line interface, refer to the AOS Command Reference Guide, also on the CD.
Unpack and Inspect the System
Each NetVanta 4305 unit is shipped in its own cardboard shipping carton. Open each carton carefully, and
avoid deep penetration into the carton with sharp objects.
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in
transit, immediately file a claim with the carrier and contact ADTRAN Customer Service (see Affidavits on
page 8).
Contents of ADTRAN Shipments
NetVanta 4305 (AC version)
Shipments of the NetVanta 4305 include the following items:
•
•
•
NetVanta 4305 base unit with attached mounting ears
ADTRAN OS Documentation CD
Support Card
NetVanta 56K/64K NIM (1200861L1)
Shipments of the 56K/64K NIM include the following items:
•
•
•
56K/64K Network Interface Module
Quick Start Guide
6-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3127004)
NetVanta T1/FT1 NIM (1200862L1)
Shipments of the T1/FT1 NIM include the following items:
•
•
•
20
T1/FT1 Network Interface Module
Quick Start Guide
15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Introduction to the NetVanta 4305
NetVanta T1/FT1+ DSX-1 NIM (1200863L1)
Shipments of the T1/FT1 + DSX-1 NIM include the following items:
•
•
•
T1/FT1 + DSX-1 Network Interface Module
Quick Start Guide
15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
NetVanta E1/FE1 NIM (1200868L1)
Shipments of the E1/FE1 NIM include the following items:
•
•
•
E1/FE1 Network Interface Module
Quick Start Guide
15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
NetVanta Dual T1 NIM (1200872L1)
Shipments of the T1/E1 NIM include the following items:
•
•
•
Two T1/E1 Network Interfaces
Quick Start Guide
Two 15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
NetVanta Serial NIM (1200866L1)
Shipments of the Serial NIM include the following items:
•
•
Serial Network Interface Module
Quick Start Guide
NetVanta E1/FE1+ G.703 Drop NIM (1200878L1)
Shipments of the E1/FE1+ G.703 NIM include the following items:
•
•
•
E1/FE1+ G.703 Network Interface Module
Quick Start Guide
15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
NetVanta Octal T1 Wide NIM (1200843L1)
Shipments of the Octal T1 Wide Option Module include the following items:
•
•
•
Octal T1 Wide Network Interface Module
Quick Start Guide
Eight 15-foot RJ-45 to RJ-45 cables (ADTRAN P/N 3125M008@A)
NetVanta Analog Modem DIM (1200864L1)
Shipments of the Analog Modem DIM include the following items:
•
•
•
Analog Modem Dial Backup Interface Module
Quick Start Guide
RJ-45 to RJ-11 cable (ADTRAN P/N 3125M007@A)
NetVanta ISDN BRI DIM (1200865L1)
Shipments of the ISDN BRI DIM include the following items:
•
•
ISDN BRI Dial Backup Interface Module
Quick Start Guide
61200890L1-34B
© 2004 ADTRAN, Inc.
21
Introduction to the NetVanta 4305
•
NetVanta 4305 Hardware Installation Guide
RJ-45 to RJ-11 cable (ADTRAN P/N 3125M007@A)
NetVanta ISDN S/T DIM (1200875L1)
Shipments of the ISDN S/T DIM include the following items:
•
•
•
ISDN S/T Dial Backup Interface Module
Quick Start Guide
RJ-45 to RJ-11 cable (ADTRAN P/N 3125M007@A)
NetVanta VPN Accelerator Card (1202368L1)
Shipments of the VPN Accelerator Card include the following items:
•
•
VPN Accelerator Card
Quick Start Guide
Option modules are intended to be serviced by qualified service personnel only.
System bundles are shipped with a base unit, a network interface module, and other appropriate contents based on the system-level solution ordered.
22
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
2.
Physical Description
PHYSICAL DESCRIPTION
Reviewing the Base Unit Front Panel Design
Figure 1 shows the NetVanta 4305 front panel.
STATUS
NET 1
WAN
DBU
TD
RD
NET 2
WAN
DBU
TD
RD
LAN 1
TD
RD
LNK
LAN 2
TD
RD
LNK
WIDE SLOT 1
STATUS
ACTIVITY
TEST
NetVanta 4305
Figure 1. NetVanta 4305 Front Panel Layout
Front Panel LEDs
Table describes the front panel LEDs.
Table 1. NetVanta 4305 LEDs
For these
LEDs…
This activity…
Indicates that…
Green (blinking)
Unit is powering up. On power-up the STAT LED blinks rapidly
for five seconds, during which time the user may escape to boot
mode from the console port.
Green (solid)
Power is on and self-test passed.
Red (solid)
Power is on, but the self-test failed or the boot mode (if
applicable) code could not be booted.
Off
No NIM is installed or interface is administratively down.
Green (solid)
Link is up and everything is operational.
Red (solid)
An alarm condition is occurring on the WAN interface, or there is
a self-test failure.
Yellow (solid)
Unit is in test.
Off
No DIM is installed.
Green (solid)
DIM is ready. For the ISDN BRI DIM, green solid indicates that
the negotiation with the switch is complete.
Green (blinking)
Unit is in dial backup.
Red (solid)
An alarm condition is occurring on the DBU interface, or there is
a self-test failure.
Yellow (solid)
Unit is in test.
Green (blinking)
There is activity on the WAN or DBU port.
Off
There is no activity on the WAN or DBU port.
Green (blinking)
There is activity on the Ethernet port.
Off
There is no activity on the Ethernet port.
STATUS
NET 1/ NET 2
WAN
NET 1/ NET 2
DBU
NET 1/ NET 2
TD/RD
LAN 1/ LAN 2
TD/RD
61200890L1-34B
© 2004 ADTRAN, Inc.
23
Physical Description
NetVanta 4305 Hardware Installation Guide
Table 1. NetVanta 4305 LEDs (Continued)
For these
LEDs…
LAN 1/ LAN 2
LNK
WIDE SLOT 1
STATUS
WIDE SLOT 1
ACTIVITY
WIDE SLOT 1
TEST
24
This activity…
Indicates that…
Green (solid)
The 10BaseT Ethernet link is up.
Yellow (solid)
The 100BaseT Ethernet link is up.
Off
The card is not installed.
Green (solid)
The card is recognized by the system.
Red (solid)
Alarm condition with card.
Green (blinking)
There is data activity on the card (e.g., for the Octal T1 module,
this indicates TD/RD data).
Off
There is no activity on card.
Off
There is no test running.
Yellow (solid)
The card is in test mode.
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Physical Description
Reviewing the Rear Panel Design
Figure 2 shows the rear panel for the NetVanta 4305. The chassis is shown with the T1/FT1+DSX-1 NIM
installed.
ETH 0/2
WAN-T1
WAN-T1
DSX-1
DSX-1
DBU
DBU
WAN-T1
DSX-1
DBU
100-250VAC
50/60Hz
CONSOLE
SLOT 3 WIDE MODULE
SLOT 2 NET/DBU
SLOT 1 NET/DBU
ETH 0/1
Figure 2. NetVanta 4305 Rear Panel Layout
Rear Panel Interfaces and LEDs
10/100BaseT Ethernet Interface and Activity LEDs
The Ethernet ports (ETH 0/1, ETH 0/2) are RJ-48C connectors with LEDs. The yellow activity LED
flashes when data traffic is being sent or received on the Ethernet port. The green link LED is on when
the router has a good connection to the LAN. See Table A-1 on page 45 for the Ethernet port pinout.
The Ethernet port provides the following:
•
•
•
•
10BaseT or 100BaseT with a single connector
Auto-negotiation
CSMA/CD
IEEE 802.3 compatibility
Console Interface
The CONSOLE interface is an EIA-232 serial port (DCE) which provides for local management and
configuration (via a DB-9 female connector). Table A-2 on page 45 shows the CONSOLE port pinouts.
Connection directly to an external modem requires a cross-over cable.
NET/DBU Card Slots
The SLOT 1 NET/DBU and SLOT 2 NET/DBU card slots support various NIM plug-in cards. These
card options are described in the section Option Modules on page 26.
Power Supply
The NetVanta 4305 has a worldwide auto-ranging AC power supply with an IEC connector. The
appropriate 3-prong cable is included in the shipment. Please refer to Supplying Power to the Unit on
page 40 for connection details.
61200890L1-34B
© 2004 ADTRAN, Inc.
25
Option Modules
3.
NetVanta 4305 Hardware Installation Guide
OPTION MODULES
The NetVanta 4305 accepts several option modules designed to meet a variety of networking requirements.
The option modules are of three types: plug-in Network Interface Modules (NIMs), plug-on Dial Backup
Interface Modules (DIMs), and Wide NIMs.
NIMs are cards which plug directly into the option module slot (labeled SLOT 1 NET/DBU or SLOT 2
NET/DBU), located on the rear of the base unit. These cards provide the following types of interfaces:
• NetVanta 56K/64K NIM (P/N 1200861L1) on page 27
• NetVanta T1/FT1 NIM (P/N 1200862L1 or P/N 1202862L1) on page 28
• NetVanta T1/FT1+DSX-1 NIM (P/N 1200863L1 or P/N 1202863L1) on page 29
• NetVanta Dual T1 NIM (P/N 1200872L1) on page 30
• NetVanta Serial NIM (P/N 1200866L1) on page 31
• NetVanta E1/FE1 NIM (P/N 1200868L1) on page 32
• NetVanta E1/FE1 NIM (P/N 1200868L1) on page 32
• NetVanta E1/FE1 with G.703 Drop NIM (P/N 1200878L1) on page 33
Wide NIMs are cards which plug directly into SLOT 3 (the Wide Interface Module slot) located on the rear
of the base unit. These cards provide the following types of interfaces:
•
Octal T1/E1 Wide NIM (P/N 1200843L1)
DIMs are plug-on cards which plug directly on to the NIM prior to installation into the base unit. A DIM
must be plugged on to a NIM in order for the DBU port on the NIM to be active. The NetVanta 4305
supports three different DIMs (only two can be installed simultaneously):
•
•
•
NetVanta Analog Modem DIM (P/N 1200864L1) on page 35
NetVanta ISDN BRI DIM (P/N 1200865L1) on page 36
NetVanta ISDN S/T DIM (P/N 1200875L1) on page 37
This section describes each module, providing individual card specifications and features. Refer to
Connector Pin Definitions on page 45 for pinout information. Installing Dial Backup and Network
Interface Modules on page 41 provides information on card installation.
26
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Option Modules
Network Interface Modules
NetVanta 56K/64K NIM (P/N 1200861L1)
The 56K/64K NIM (shown in Figure 3) provides a WAN-DDS interface for the NetVanta 4305. Refer to
Table A-3 on page 46 for the WAN-DDS connector pinout, and refer to Table A-9 on page 49 for the DBU
connector pinout. An optional DIM is required for dial backup applications.
Figure 3. NetVanta 56K/64K NIM
Features and Specifications
Operating Modes
•
Dedicated DDS (leased line)
DDS Interface
•
•
•
•
RJ-48C
4-wire, full duplex
-45 dB receiver sensitivity all rates
Data Rates: 56K, 64K, and Auto
Clock Source
•
•
Network
Internal
Diagnostics
•
CSU and DSU Loopbacks
61200890L1-34B
Relevant Requirements/Standards
•
•
•
•
•
EMC - see Electromagnetic Compatibility
(EMC) Table on page 6.
ACTA/FCC Part 68
Industry Canada CS03
UL and CUL
AT&T TR 62310
Environmental
•
•
•
Operating Temperature: 0 to 50 oC
Storage Temperature: -40 to 85 oC
Relative Humidity: Up to 95% noncondensing
Physical
•
© 2004 ADTRAN, Inc.
Dimensions: 4.25" x 2.75"
27
Option Modules
NetVanta 4305 Hardware Installation Guide
NetVanta T1/FT1 NIM (P/N 1200862L1 or P/N 1202862L1)
The T1/FT1 NIM (shown in Figure 4) provides a T1 (full T1 or fractional T1) WAN interface for the
NetVanta 4305. Refer to Table A-4 on page 46 for the WAN-T1 connector pinout, and refer to Table A-9
on page 49 for the DBU connector pinout. An optional DIM is required for dial backup applications.
WAN-T1
DBU
Figure 4. NetVanta T1/FT1 NIM
Features and Specifications
Relevant Requirements/Standards
•
Operating Modes
•
•
T1/FT1 Frame Relay
T1/FT1 PPP
T1/FT1 Interface
•
•
•
•
•
•
•
•
Line Rate: 1.544 Mbps +/- 75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 Channelized
(multiples of 56/64 kbps)
Input Signal: 0 to -36 dB (DS-1)
Line Build-Out: 0, -7.5, -15, -22.5 dB
Connector: RJ-48C
DS0 Assignment: Programmable
•
•
•
•
•
•
Environmental
•
•
•
Clock Source
•
•
Network
Internal
EMC - see Electromagnetic Compatibility
(EMC) Table on page 6.
ACTA/FCC Part 68
Industry Canada CS03
UL and CUL
T1 Interface: Pub 62411
ESF Format Interface: TR. 194
ESF Performance Monitoring: TR. 54016
and T1.403
Operating Temperature: 0 to 50 oC
Storage Temperature: -40 to 85 oC
Relative Humidity: Up to 95%
noncondensing
Physical
•
Dimensions: 4.25" x 2.75"
Diagnostics
•
•
•
•
28
Test pattern generation and detection: 511,
QRSS (2nd Gen only)
Network loopbacks (local and remote);
responds to both INBAND and FDL loop
codes
Alarm generation and detection
Network and user sets of performance data
(15 minutes and 24 hours)
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Option Modules
NetVanta T1/FT1+DSX-1 NIM (P/N 1200863L1 or P/N 1202863L1)
The T1/FT1 + DSX-1 NIM (see Figure 5) provides a full T1 or fractional T1 network interface and a DSX1 interface. Refer to Table A-4 on page 46 for the WAN-T1 connector pinout, Table A-6 on page 47 for the
DSX-1 connector pinout, and Table A-9 on page 49 for the DBU connector pinout. An optional DIM is
required for dial backup applications.
WAN-T1
DSX-1
DBU
Figure 5. NetVanta T1/FT1+DSX-1 NIM
Features and Specifications
Diagnostics
•
•
Operating Modes
•
•
T1/FT1 Frame Relay
T1/FT1 PPP
T1/FT1 Interface
•
•
•
•
•
•
•
•
Line Rate: 1.544 Mbps +/- 75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 Channelized
(multiples of 56/64 kbps)
Input Signal: 0 to -36 dB (DS-1)
Line Build-Out: 0, -7.5, -15, -22.5 dB
Connector: RJ-48C
DS0 Assignment: Programmable
DSX-1 Interface
•
•
•
•
•
•
•
•
•
Line Interface: DSX-1 per ANSI T1.102
DSX Receiver Input Range: -10 dBdsx to
+6 dBdsx
Line Rate: 1.544 Mbps
Capacity: 1 to 24 DS0s
Line Codes: AMI, B8ZS
Framing: D4 (SF) or ESF
Line Length: 0 to 655 feet and -7.5 dB
Connector: RJ-48C
DSX-1 Interface to PBX
•
•
Test pattern generation and detection: 511
Network loopbacks (local and remote);
responds to inband loop codes (T1 interface
only)
Alarm generation and detection
Network and user sets of performance data
(15 minutes and 24 hours)
Relevant Requirements/Standards
•
•
•
•
•
•
•
EMC - see Electromagnetic Compatibility
(EMC) Table on page 6.
ACTA/FCC Part 68
Industry Canada CS03
UL and CUL
T1 Interface: Pub 62411
ESF Format Interface: TR. 194
ESF Performance Monitoring: TR. 54016
and T1.403
Environmental
•
•
•
Operating Temperature: 0 to 50 oC
Storage Temperature: -40 to 85 oC
Relative Humidity: Up to 95%
noncondensing
Physical
•
Dimensions: 4.25" x 2.75"
Clock Source
•
•
•
Network
Internal
DSX-1
61200890L1-34B
© 2004 ADTRAN, Inc.
29
Option Modules
NetVanta 4305 Hardware Installation Guide
NetVanta Dual T1 NIM (P/N 1200872L1)
The NetVanta Dual T1 NIM (see Figure 6) provides two WAN T1 interfaces for the NetVanta 4305. The
module provides up to 2.048 Mbps on each network interface. Refer to Table A-5 on page 46 for the
pinouts. Refer to Table A-10 on page 49 for the DBU connector pinout. An optional DIM is required for
dial backup applications.
Figure 6. NetVanta Dual T1 NIM
Features and Specifications
Diagnostics
•
Operating Modes
•
T1/ FT1
T1/E1 Interface
•
•
•
•
•
•
•
•
Line Rate: 1.544 Mbps +/- 75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 Channelized
(multiples of 64 kbps)
Input Signal: 0 to -36 dB (DS-1)
Line Build-Out: 0, -7.5, -15, -22.5 dB
Connector: RJ-48C
DS0 Assignment: Programmable
Clock Source
•
•
•
Network
Internal
Through
•
•
•
•
Test pattern generation and detection:
QRSS, 511, 215-1, 220-1
Network loopbacks (local and remote)
Responds to inband loop codes (T1
interface only)
Alarm generation and detection
Network performance data (15 minutes
and 24 hours)
Relevant Requirements/Standards
•
•
•
•
•
ACIF S016
ACA TS001
ETSI TBR 12 / TBR 13
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
ITU G.703, ITU-T G.704 (CRC-4), ITUT G.823, ITU-T G.797
Environmental
•
•
•
Operating temperature: 0 ° to 50 °C
Storage Temperature: -40 to 85 oC
Relative Humidity: Up to 95%
noncondensing
Physical
•
30
© 2004 ADTRAN, Inc.
Dimensions: 4.25” x 2.75”
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Option Modules
NetVanta Serial NIM (P/N 1200866L1)
The NetVanta Serial NIM (shown in Figure 7) is user-configurable to be either a V.35 or X.21 (V.11)
interface. This module supports rates up to a maximum of 10 Mbps. An additional V.35 (ADTRAN
P/N 1200873L1) or X.21 (ADTRAN P/N 1200874L1) cable is required (see Caution, below). Refer to
Table A-8 on page 48 for the Serial connector pinout, and refer to Table A-10 on page 49 for the DBU
connector pinout. An optional DIM is required for dial backup applications.
Cable length for the Serial NIM should not exceed 25 feet.
SERIAL
DBU
Figure 7. NetVanta Serial NIM
Features and Specifications
Relevant Requirements/Standards
•
Operating Mode
•
DTE only
Serial Interface
•
•
Provides V.35 or X.21 (V.11) electrical
interface
26-pin smart serial (DTE) connector
Clock Source
•
•
Network
Internal
•
•
•
•
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
EN60950
UL and CUL
ISO 4903 (X.21)
CCITT V.35 Synchronous (V.35)1
Environmental
•
•
•
Operating Temperature: 0 to 50 oC
Storage Temperature: -40 to 85 oC
Relative Humidity: Up to 95%
noncondensing
Physical
•
61200890L1-34B
© 2004 ADTRAN, Inc.
Dimensions: 4.25" x 2.75"
31
Option Modules
NetVanta 4305 Hardware Installation Guide
NetVanta E1/FE1 NIM (P/N 1200868L1)
The NetVanta E1 NIM (see Figure 8) provides a WAN-E1 interface for the NetVanta 4305 meeting the
requirements of ITU-T G.703/G.704. The module provides a single 2.048 Mbps network interface. Refer to
Table A-5 on page 46 for the pinouts. Refer to Table A-10 on page 49 for the DBU connector pinout. An
optional DIM is required for dial backup applications.
WAN-E1
DBU
Figure 8. NetVanta E1/FE1 NIM
Features and Specifications
Relevant Requirements/Standards
Operating Modes
•
E1/FE1
WAN-E1 Interface
•
•
•
•
•
•
Connector: RJ-48C
Line Rate: 2.048 Mbps +/- 50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
FE1 Line Rate: Channelized Timeslot (in
multiples of 64 kbps)
Receiver Sensitivity: -30 dB
Clock Source
•
•
•
Network
Internal
Through
•
•
•
•
•
ACIF S016
ACA TS001
ETSI TBR 12 / TBR 13
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
ITU G.703, ITU-T G.704 (CRC-4), ITUT G.823, ITU-T G.797
Environmental
•
•
•
Operating temperature: 0 ° to 50 °C
Storage Temperature: -40 to 85 oC
Relative Humidity: Up to 95%
noncondensing
Physical
•
Dimensions: 4.25” x 2.75”
Diagnostics
•
•
•
•
32
Network loopbacks
Network performance data (15 minutes
and 24 hours)
Test pattern generation and detection:
QRSS, 511
Alarm generation and detection
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Option Modules
NetVanta E1/FE1 with G.703 Drop NIM (P/N 1200878L1)
The NetVanta E1/FE1 with G.703 Drop NIM (see Figure 9) provides a single WAN-E1 interface
(2.043 Mbps) with user-selectable TS0 assignment and a G.703 drop port which may be used to drop and
insert traffic to an E1 PBX. Refer to Table A-7 on page 49 for the E1 pinouts. Refer to Table A-7 on page
47 for the G.703 pinouts. Refer to Table A-10 on page 49 for the DBU connector pinout. An optional DIM
is required for dial backup applications.
WAN-E1
G.703
DBU
Figure 9. NetVanta E1/FE1 with G.703 Drop NIM
•
Features and Specifications
Operating Modes
•
E1/FE1
•
WAN-E1 Interface
•
•
•
•
•
•
Connector: RJ-48C
Line Rate: 2.048 Mbps +/- 50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
FE1 Line Rate: Channelized Timeslot (in
multiples of 64 kbps)
Receiver Sensitivity: -30 dB
G.703 Interface
•
•
•
•
•
•
Connector: RJ-48C
Line Rate: 2.048 Mbps
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
Capacity: 1 to 31 timeslots
Receiver Sensitivity: -30 dB
Clock Source
•
•
•
Network
Internal
Through
Diagnostics
•
•
Network performance data (15 minutes
and 24 hours)
Test pattern generation and detection:
QRSS, 511
Alarm generation and detection through
SNMP
Relevant Requirements/Standards
•
•
•
•
•
ACIF S016
ACA TS001
ETSI TBR 12 / TBR 13
EMC - see Electromagnetic
Compatibility (EMC) Table on page 6.
ITU G.703, ITU-T G.704 (CRC-4), ITUT G.823, ITU-T G.797
Environmental
•
Operating temperature: 0 ° to 50 °C
•
•
Storage Temperature: -40 to 85 oC
Relative Humidity: Up to 95%
noncondensing
Physical
•
Dimensions: 4.25” x 2.75”
Network loopbacks
61200890L1-34B
© 2004 ADTRAN, Inc.
33
Option Modules
NetVanta 4305 Hardware Installation Guide
NetVanta Octal T1 Wide NIM (P/N 1200843L1)
The NetVanta Octal T1 Wide NIM (shown in Figure 10) provides eight T1 (full T1 or fractional T1) WAN
interfaces. Refer to Table A-4 on page 46 for the T1 interface pinout.
Figure 10. NetVanta Octal T1 Wide NIM
Features and Specifications
Operating Modes
•
•
T1/FT1 Frame Relay
T1/FT1 PPP
T1/FT1 Interface
•
•
•
•
•
•
•
Line Rate: 1.544 Mbps +/- 75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 Channelized (multiples of 56/64 kbps)
Input Signal: 0 to -36 dB (DS-1)
Line Build-Out: 0, -7.5, -15, -22.5 dB
DS0 Assignment: Programmable
Agency Approvals
•
•
•
•
•
•
FCC Part 15, Class A
UL/CUL 60950
EN 60950/IEC 60950
AS/NZS 60950
EN 55022
EN 55024
Environmental
•
•
•
34
Operating Temperature: 0° to 50°C
Storage Temperature: -20° to 70°C
Relative Humidity: 95% non-condensing
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Option Modules
Dial Backup Interface Modules
NetVanta Analog Modem DIM (P/N 1200864L1)
The Analog Modem DIM provides a modem with data rates up to 33.6 kbps for the NetVanta 4305. This
DIM is a plug-on card that connects to the NIM. For installation instructions, see Installing Dial Backup
and Network Interface Modules on page 41.
Features and Specifications
Features
•
•
ITU V.90 compliant
Async
Relevant Requirements/Standards
•
•
•
•
EMC - see Electromagnetic Compatibility (EMC) Table on page 6.
ACTA/FCC Part 68
Industry Canada CS03
UL and CUL
Environmental
•
•
•
Operating Temperature: 0 to 50 oC
Storage Temperature: -40 to 85 oC
Relative Humidity: Up to 95% noncondensing
Physical
•
Dimensions: 3.75" x 2.5"
61200890L1-34B
© 2004 ADTRAN, Inc.
35
Option Modules
NetVanta 4305 Hardware Installation Guide
NetVanta ISDN BRI DIM (P/N 1200865L1)
The NetVanta ISDN BRI DIM provides dial backup access to the public switched telephone network
(PSTN) via Basic Rate ISDN for the NetVanta 4305. This DIM is a plug-on module that connects to the
NIM. For installation instructions, see Installing Dial Backup and Network Interface Modules on page 41.
Features and Specifications
Features
•
•
•
•
Clear Channel and BONDING Mode 1 call protocols
Network support for 64 kbps (1B channel) or 128 kbps (2B channels)
D channel switch compatibility with AT&T 5ESS, Northern Telecom DMS-100, and National
ISDN-1
V.54 network loopback support
Relevant Requirements/Standards
•
•
•
•
EMC - see Electromagnetic Compatibility (EMC) Table on page 6.
ACTA/FCC Part 68
Industry Canada CS03
UL and CUL
Environmental
•
•
•
Operating Temperature: 0 to 50 °C
Storage Temperature: -40 to 85 °C
Relative Humidity: Up to 95% non-condensing
Physical
•
36
Dimensions: 3.75" x 2.5”
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Option Modules
NetVanta ISDN S/T DIM (P/N 1200875L1)
The NetVanta ISDN S/T DIM provides dial backup access to the public switched telephone network
(PSTN) via Basic Rate ISDN for the NetVanta 4305. This DIM is a plug-on module that connects to the
NIM. For installation instructions, see Installing Dial Backup and Network Interface Modules on page 41.
Features and Specifications
Features
•
•
•
Supports PPP dial backup
Network support for 64 kbps (1B-channel)
D-channel switch compatibility with AT&T 5ESS, Northern Telecom DMS-100, National ISDN-1,
and Euro-ISDN
Relevant Requirements/Standards
•
•
•
•
ACIF S031
ACA TS001
EMC - see Electromagnetic Compatibility (EMC) Table on page 6.
EN 60950
Environmental
•
•
•
Operating Temperature: 0 to 50 °C
Storage Temperature: -40 to 85 °C
Relative Humidity: Up to 95% non-condensing
Physical
•
Dimensions: 3.75" x 2.5”
61200890L1-34B
© 2004 ADTRAN, Inc.
37
Unit Installation
4.
NetVanta 4305 Hardware Installation Guide
UNIT INSTALLATION
The instructions and guidelines provided in this section cover hardware installation topics such as wall
mounting/rack mounting the unit and installing option cards. These instructions are presented as follows:
• Mounting Options on page 39
• Supplying Power to the Unit on page 40
• Installing Dial Backup and Network Interface Modules on page 41
• Installing the NetVanta VPN Accelerator Card (1202368L1) on page 43
For information on router configuration for a specific application, refer to the quick start documents
provided on your ADTRAN OS Documentation CD. For details on the command line interface, refer to the
AOS Command Reference Guide (also included on your CD).
To prevent electrical shock, do not install equipment in a wet location or during a
lightning storm.
Electronic modules can be damaged by static electrical discharge. Before handling
modules, wear an antistatic discharge wrist strap to prevent damage to electrical
components. Place modules in antistatic packing material when transporting or storing.
When working on modules, always place them on an approved antistatic mat that is
electrically grounded.
Tools Required
The customer-provided tools required for the hardware installation of the NetVanta 4305 are:
•
•
•
•
•
Ethernet cable
Network cable (module-dependent)
DSX-1 cable (T1/FT1 + DSX-1 module only)
DBU cable (dial backup functions require an optional DIM)
Phillips-head screwdriver (rack mounting applications only)
To access the command line interface (CLI) of the NetVanta 4305, you will also need a
VT100 terminal or PC with terminal emulation software and a console port cable.
Instructions on how to access the CLI are given in the AOS Command Reference Guide
(provided on the ADTRAN OS Documentation CD).
38
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Unit Installation
Mounting Options
If you have purchased the VPN Accelerator Card, install it first. See Installing the
NetVanta VPN Accelerator Card (1202368L1) on page 43.
The NetVanta 4305 may be installed in a tabletop, wall mount, or 19-inch rack mount configuration. The
following sections provide step-by-step instructions for rack mounting and wall mounting.
Rack Mounting NetVanta 4305
The NetVanta 4305 is housed in a 1U high, rack-mountable chassis which can be installed into 19-inch
equipment racks. Follow these steps to mount the NetVanta 4305 into a rack:
Instructions for Rack Mounting NetVanta
Step
Action
1
Position the NetVanta 4305 in a stationary equipment rack. This unit takes up 1U of space. To
allow proper grounding, scrape the paint from the rack around the mounting holes where the
NetVanta 4305 will be positioned.
2
Have someone else hold the unit in position as you install two mounting bolts through the unit’s
brackets and into the equipment rack using a #2 Phillip’s screwdriver.
3
Proceed to the steps given in Supplying Power to the Unit on page 40.
Be careful not to upset the stability of the equipment mounting rack when installing this
product.
Wall Mounting NetVanta 4305
Instructions for Wall Mounting NetVanta 4305
Step
Action
1
Remove the mounting ears. Rotate them 90o so that the portion of the bracket with the
mounting holes is flush with the bottom of the chassis, and reattach them to the chassis.
2
Decide on a location for the NetVanta 4305. Keep in mind that the unit needs to be mounted at
or below eye-level so that the LEDs are viewable. Important! Mount the chassis with LEDs
facing to the side (not facing up or down).
Warning! Do not mount the chassis with the right-side fans facing down.
3
Prepare the mounting surface by attaching a board (typically plywood, 3/ 4" to 1" thick) to a wall
stud. Important! Mounting to a stud ensures stability. Using sheetrock anchors may not
provide sufficient long-term stability.
61200890L1-34B
© 2004 ADTRAN, Inc.
39
Unit Installation
NetVanta 4305 Hardware Installation Guide
Instructions for Wall Mounting NetVanta 4305 (Continued)
Step
Action
4
Have someone else hold the unit in position as you install two 3/ 32" to 1/ 8" (1 1/ 2" or greater
in length) wood screws through the unit’s brackets and into the mounted board.
5
Proceed to the steps given in Supplying Power to the Unit on page 40.
Supplying Power to the Unit
As shipped, each NetVanta 4305 is set to factory default conditions. After installing the base unit and any
option modules, the NetVanta 4305 is ready for power-up. To power-up the unit, ensure that the unit is
properly connected to an appropriate power source (as outlined in the sections below).
NetVanta 4305 (AC)
The AC-powered NetVanta 4305 comes equipped with an auto-sensing 100-250 VAC, 50-60 Hz power
supply. The maximum power consumption is 75 Watts. A grounded, three-plug detachable cable is
included with the shipment.
40
•
•
•
Use only copper conductors when making power connections.
Install unit in accordance with Article 400 and 364.8 of the NEC NFPA 70.
A readily accessible disconnect device, that is suitably approved and rated, shall be
incorporated in the field wiring.
•
Maximum recommended ambient operating temperature is 50 °C
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Unit Installation
Installing Dial Backup and Network Interface Modules
The DIMs plug on to the NIMs. The NIMs are then installed in the rear panel option module slot. The
following tables list the installation steps. See Figure 11 below and Figure 12 on page 42.
Always remove power from the unit prior to removing or installing a module.
Improper installation may result in damage to the modules.
Instructions for Installing the DIMs
Step
Action
1
Remove power from the unit.
2
If the NIM is already in the NetVanta chassis, release the pins at both edges of the NIM
faceplate and slide the module out of the chassis.
3
Carefully align the P1 connector on the NIM with the J1 connector on the DIM. Using only
fingertip pressure so that neither circuit board bends or flexes, ensure that the connectors are
firmly seated. Secure the DIM to the NIM using the screws and standoff posts supplied. See
Figure 11.
4
Slide the NIM with the DIM attached into the NetVanta chassis, continuing with the normal NIM
installation (see Instructions for Installing the NIMs and Wide NIMs on page 42).
WAN
-T1
DBU
NOTE
:O
REQUPTIONAL
IRED MOD
FOR D ULE
BU
Figure 11. Installing DIMs
61200890L1-34B
© 2004 ADTRAN, Inc.
41
Unit Installation
NetVanta 4305 Hardware Installation Guide
Instructions for Installing the NIMs and Wide NIMs
Step
Action
1
Remove power from the unit.
2
Slide the option module into the option slot until the module is firmly seated against the front of
the chassis.
3
Secure the pins at both edges of the module.
4
Connect the cables to the associated device(s).
5
Restore power to the unit.
ETH 0/2
WAN-T1
DSX-1
DBU
100-250VAC
50/60Hz
CONSOLE
SLOT 3 WIDE MODULE
SLOT 2 NET/DBU
WAN-T1
DSX-1
SLOT 1 NET/DBU
ETH 0/1
DBU
Figure 12. NIM and DIM Installation
Your NetVanta 4305 is now ready to be configured and connected to the network. For more information on
configuration for a specific application, refer to the quick start documents provided on your ADTRAN OS
Documentation CD. For details on the command line interface, refer to the AOS Command Reference
Guide (also included on your CD).
42
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Unit Installation
Installing the NetVanta VPN Accelerator Card (1202368L1)
The optional VPN Accelerator Card plugs into a 32-bit PCI slot and is designed to be used in the
NetVanta 4305 to provide encryption/decryption and security acceleration services. The card provides the
following security services to the host processor: DES, Triple-DES, AES, SHA-1, MD5, and Random
Number Generation. Performance metrics include 528 Mbps-DES, 176 Mbps-3DES, and 422 Mbps-AES.
The power consumption of the card does not exceed 2 Watts.
Instructions for Installing the VPN Accelerator Card
Step
Action
1
Remove power from the unit.
2
Remove the nine screws and, if necessary, two mounting brackets (see Figure 13).
3
Using a 3/16” hex driver, remove the two jack screws located on either side of the DB-9 port.
4
Carefully lift and remove the unit’s cover to expose the circuit board.
5
Gently slide the accelerator card into the PC card slot as shown. The card is keyed to fit into the
slot only one way. To avoid damaging the card pins, do not use excessive force.
6
Replace the unit cover, screws, and mounting brackets.
7
Restore power to the unit.
Figure 13. VPN Card Installation
61200890L1-34B
© 2004 ADTRAN, Inc.
43
Unit Installation
44
NetVanta 4305 Hardware Installation Guide
© 2004 ADTRAN, Inc.
61200890L1-34B
APPENDIX A. CONNECTOR PIN DEFINITIONS
The following tables provide the pin assignments for the base unit, network interface modules (NIMs), and
dial backup interface modules (DIMs).
Base Unit Pinouts
Table A-1. 10/100BaseT Ethernet Port Pinouts
Pin
Name
Description
1
TX1
Transmit Positive
2
TX2
Transmit Negative
3
RX1
Receive Positive
4,5
—
Unused
6
RX2
Receive Negative
7,8
—
Unused
Table A-2. Console Port (DCE) Pinout for NetVanta 4305 (p/n 1200890L1)
Pin
Name
Description
1
DCD
Data Carrier Detect (output)
2
RD
Receive Data (output)
3
TD
Transmit Data (input)
4
DTR
Data Terminal Ready (input)
5
SG
Signal Ground
6
DSR
Data Set Ready Tied to pin 1 (output)
7
—
Not connected
8
CTS
Clear to Send Tied to pin 1 (output)
9
—
Not connected
Connection directly to an external modem requires a cross-over cable.
61200890L1-34B
© 2004 ADTRAN, Inc.
45
Appendix A. Connector Pin Definitions
NetVanta 4305 Hardware Installation Guide
Network Interface Module (NIM) and Wide NIM Pinouts
Table A-3. WAN-DDS Connector Pinouts
Pin
Name
Description
1
R1
Transmit data to the network—Ring 1
2
T1
Transmit data to the network—Tip 1
3-6
—
Unused
7
T
Receive data from the network—Tip
8
R
Receive data from the network—Ring
Table A-4. WAN-T1 Connector Pinouts
Pin
Name
Description
1
R1
Receive data from the network—Ring 1
2
T1
Receive data from the network—Tip 1
3
—
Unused
4
R
Transmit data toward the network—Ring
5
T
Transmit data toward the network—Tip
6-8
—
Unused
Table A-5. WAN-E1 Connector Pinouts
Pin
Name
Description
1
R1
Receive data from the network
2
T1
Receive data from the network
3
—
Unused
4
R
Transmit data toward the network
5
T
Transmit data toward the network
6-8
—
Unused
46
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Appendix A. Connector Pin Definitions
Table A-6. DSX-1 Connector Pinout
Pin
Name
Description
1
R
Transmit data toward the DTE—Ring
2
T
Transmit data toward the DTE—Tip
3
—
Unused
4
R1
Receive data from the DTE—Ring 1
5
T1
Receive data from the DTE—Tip 1
6-8
—
Unused
Table A-7. G.703 Connector Pinouts
Pin
Name
Description
1
R
Transmit data toward the DTE—Ring
2
T
Transmit data toward the DTE—Tip
3
—
Unused
4
R1
Receive data from the DTE—Ring 1
5
T1
Receive data from the DTE—Tip 1
6-8
—
Unused
61200890L1-34B
© 2004 ADTRAN, Inc.
47
Appendix A. Connector Pin Definitions
NetVanta 4305 Hardware Installation Guide
Table A-8. Serial NIM Connector Pinouts
Pin
Name
Pin
Name
1
TD_A
14
TD_B
2
ETC_A
15
ETC_B
3
TCLK_A
16
TCLK_B
4
RCLK_A
17
RCLK_B
5
RD_A
18
RD_B
6
DCD_A
19
Unused
7
DTR_A
20
Unused
8
RTS_A
21
Unused
9
RTS_B (V.11 only)
22
Unused
10
CTS_B (V.11 only)
23
Unused
11
CTS_A
24
Unused
12
DSR_A
25
Unused
13
TM_A
26
Ground
48
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Appendix A. Connector Pin Definitions
Dial Backup (DBU) Connectors
Table A-9 describes the pinouts for the following modules: 56/64K, T1/FT1 (1st generation), and T1/
FT1+DSX-1 (1st generation).
Table A-9. DBU Connector Pinouts
Pin
Name
Description
1
R1
Network–Ring 1
2
T1
Network—Tip 1
3
—
Unused
4
T
Network–Tip
5
R
Network–Ring
6-8
—
Unused
Table A-10 describes the pinouts for the following modules: Serial, E1/FE1, E1/FE1 with G.703 Drop, T1/
FT1 (2nd generation), Dual T1 NIM, and T1/FT1+DSX-1 (2nd generation).
Table A-10. DBU Connector Pinouts
Pin
Name
Description
1-2
—
Unused
3
R1
Network–Ring 1
4
R
Network–Ring
5
T
Network—Tip
6
T1
Network—Tip 1
7-8
—
Unused
An optional DIM is required for dial backup applications.
61200890L1-34B
© 2004 ADTRAN, Inc.
49
Appendix A. Connector Pin Definitions
50
NetVanta 4305 Hardware Installation Guide
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
Numerics
10/100BaseT Ethernet 19
interface 45
pinout 45
56K/64K interface 19
A
accelerator card 43
affidavits 8
C
console port
pinout 45
contents of shipment 20
D
DBU interface 23, 49
pinout 23, 49
Dial Backup Interface Modules (DIMs)
NetVanta Analog Modem DIM
features and specifications 35
shipping contents 21
NetVanta ISDN BRI DIM
features and specifications 36
shipping contents 21
NetVanta ISDN S/T DIM
features and specifications 37
shipping contents 22
DIM installation 41
dimensions 20
DSX-1 interface
pinout 47
dual T1/E1 interface 19
E
E1/FE1 interface 19
E1/FE1 w/ G.703 drop interface 19
F
features of the NetVanta 4305 19
Frame Relay 19
front panel 23
G
G.703 interface
pinout 47
I
installing NetVanta unit 38
installing the accelerator card 43
L
LAN 1/LAN 2 TD/RD LED 23
61200890L1-34B
© 2004 ADTRAN, Inc.
51
NetVanta 4305 Hardware Installation Guide
LEDs 23
front panel 23
M
mounting options
rack 39
wall 39
N
NET 1/NET 2 DBU LED 23
NET 1/NET 2 TD/RD LED 23
NET 1/NET 2 WAN LED 23
NetVanta 4305
features and specifications 19
front panel 23
installation 38
rear panel 25
shipping contents 20
NetVanta VPN Accelerator Card
installation 43
shipping contents 22
Network Interface Modules (NIMs) 27
NetVanta 56K/64K NIM
features and specifications 27
shipping contents 20
NetVanta Dual T1/E1 NIM
features and specifications 30
shipping contents 21
NetVanta E1/FE1 NIM
features and specifications 32
shipping contents 21
NetVanta E1/FE1 w/ G.703 Drop NIM
features and specifications 33
shipping contents 21
NetVanta Octal T1 Wide NIM
features and specifications 34
shipping contents 21
NetVanta Serial NIM
features and specifications 31
shipping contents 21
NetVanta T1/FT1 NIM
features and specifications 28
shipping contents 20
NetVanta T1/FT1+DSX-1 NIM
features and specifications 29
shipping contents 21
52
© 2004 ADTRAN, Inc.
61200890L1-34B
NetVanta 4305 Hardware Installation Guide
O
option modules 26
P
pinouts
10/100BaseT Ethernet 45
console port 45
DBU 23, 49
DSX-1 47
G.703 47
serial 48
WAN-DDS 46
WAN-E1 46
WAN-T1 46
power 40
NetVanta 4305 (AC) 40
PPP 19
product registration 10
R
rack mounting 39
rear panel 25
LEDs 25
repair and return 10
S
serial interface 19
pinout 48
STATUS LED 23
T
T1/FT1 interface 19
T1/FT1 with DSX-1 interface 19
tools required for installation 38
trademarks 2
U
unit installation 38
unpack and inspect the system 20
V
VPN accelerator card 20
W
wall mounting 39
WAN-DDS interface
pinout 46
WAN-E1 interface
pinout 46
WAN-T1 interface
pinout 46
warranty 10
61200890L1-34B
© 2004 ADTRAN, Inc.
53