Sargent P2 PASSPORT 1000 Specifications

P2
PASSPORT 1000
Exit Device
Installation Instructions
A8012F
03/14
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission
of Sargent Manufacturing Company is prohibited.
Table of Contents
1
1
Warning ....................................................................................2
2
General Description..................................................................3
3
Hardware Specifications..........................................................3
4
Electronic Specifications..........................................................3
5
Parts Breakdown......................................................................4
6
Rim Type 8877/8878 Exit Device Installation..........................7
7
Mortise Type 8977/8978 Exit Device Installation..................17
8
Operational Check..................................................................25
Warning
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
03/31/14
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada:
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement.
L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter
n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.”
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved
for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain
maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
!
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing
makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority
Having Jurisdiction) to ensure compliance with all applicable codes and ratings.
To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling
electronic components:
•
Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door.
•
Leave components (reader and controller) protected in their respective anti-static bags until ready for installation
•
Do not touch pins, leads or solder connections on the circuit boards
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
2
General Description
The SARGENT Passport 1000 P2 Exit Device features HID® multiCLASS SE™ technology, offering simultaneous
support for multiple credential formats as well as an easy migration path to higher security credentials and NFC
mobile access.
Designed specifically for the campus market, the SARGENT Passport 1000 P2 WiFi exit device provides
customized access control with magnetic swipe and optional contactless reader and/or keypad, as well as
detailed audit capabilities.
•
Using WiFi technology and coupled with third party software, the P2 lock offers a complete, integrated access
control system.
•
The Passport 1000 P2 operates on six (6) “AA” alkaline batteries and may be used for both indoor and
outdoor applications.
Note: A weather-protective gasket is recommended for outdoor applications.
Hardware Specifications
Passport 1000 P2 Rim Exit
Passport 1000 P2 Mortise Exit
•
•
•
•
•
•
•
•
•
•
4
•
Complete lockset with on-board memory
Magnetic swipe standard with optional multiCLASS SE
reader and/or keypad
ADA compliant
Easily retrofits existing Passport 1000 mortise
lock exit devices
Latch – 3/4” throw, anti-friction, brass
Outside lever is unlocked through access
control credentials only
Exit Device always allows immediate egress
UL Listed for panic and available UL Listed for fire
rated openings (12- option)
SARGENT exit devices furnished for 1-3/4” standard
(specify 31- and thickness for thicker doors)
Key override standard with 8977
[#46 (1-3/4”) mortise cylinder supplied]
Available with ET Trim only (many lever designs available)
•
Wireless (WiFi 802.11 b/g/n), battery-operated
•
2,400 users per lock; 10,000 event audit trail
•
Multiple time zone and holiday access scheduling
•
First-In unlock configuration, based on specified time
schedule
•
Input Power: DC 9V, 1.5A (6 AA alkaline batteries
or optional hard-powered)
•
•
•
•
•
•
•
•
Electronic Specifications
• HID® multiCLASS SE™ technology offers support
for the following credentials:
•
•
High Frequency (13.56 MHz):
•
HID iCLASS®
•
HID iCLASS SE® (SIO-enabled)
•
HID iCLASS® Seos™
•
HID MIFARE SE
•
HID DESfire® EV1 SE
•
Uses existing Magstripe keycards (track 2)
•
MIFARE Classic
•
•
DESfire EV1
Magnetic Stripe Card Coercivity: HiCo (4000
Oersted) or LoCo (300 Oersted)
•
FeliCa
•
Support for most advanced wireless encryption and
authentication standards.
®
Low Frequency (125 kHz):
•
For specific security information, please contact your local
ASSA ABLOY Door Security Solutions sales consultant or call
800-810-WIRE.
HID Prox®
•
Magnetic Stripe
•
NFC-enabled Mobile Phones
03/31/14
•
•
•
•
Complete lockset with on-board memory
Magnetic swipe standard with optional multiCLASS SE
reader and/or keypad
ADA compliant
Easily retrofits existing Passport 1000 rim exit devices
Latch – 3/4” throw, stainless steel
Outside lever is unlocked through access
control credentials only
Exit device always allows immediate egress
UL Listed for panic and available UL Listed for
fire rated openings (12- option)
SARGENT exit devices furnished for 1-3/4” standard
(specify 31- and thickness for thicker doors)
Accepts all SARGENT rim cylinders (8877 only)
Key override standard with 8877
(#34 rim cylinder supplied))
Available with ET trim only (many lever designs available)
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
3
3
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
Parts Breakdown
P2 WiFi Lock with Magnetic Card Swipe With or Without Keypad
4
3
1
2
ITEM No.
1
2
3
PART No.
DESCRIPTION
52-3583-[finish]
Outside Escutcheon Assemby, mag stripe
52-3582-[finish]
Outside Escutcheon Assemby, mag stripe and Keypad (shown)
52-4244-[finish]
Outside Escutcheon Assembly, mag stripe, keypad and HID 125kHz Prox
52-4759-[finish]
Outside Escutcheon Assemby, iCLASS, keypad, mag stripe, Prox, smart card (MIFARE, DESFIRE)
52-4777-[finish]
Outside Escutcheon Assemby, iCLASS, mag stripe, Prox, smart card (MIFARE, DESFIRE)
52-4787-[finish]
Outside Escutcheon Assemby, FeliCa, keypad, mag stripe, Prox
52-4788-[finish]
Outside Escutcheon Assemby, FeliCa, mag stripe, Prox
52-4779
Mounting Plate Assembly
52-5409
WiFi Controller Assembly
52-4796
WiFi Radio Module (not shown)
4
52-4776-[finish]
Inside Escutcheon Assembly with Privacy Button
5
52-5373
Door Position Switch Kit
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
5
03/31/14
5
4
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
Parts Breakdown (continued)
Items Supplied with Exit Device
8877 and 8977 Series Exit Device Contents
8878 and 8978 Series Exit Device Contents
•
•
•
•
•
•
•
•
•
Outside escutcheon with magnetic swipe standard
with optional proximity reader and/or keypad
Outside motorized ET trim
8800 Rim or 8900 Mortise Lock Exit Device
#46 Mortise cylinder for 8977 (1-3/4” Door)
#34 Rim cylinder for 8877
Inside escutcheon with circuit board and battery pack
6 “AA” alkaline batteries
Screw Pack
•
•
•
•
•
Outside escutcheon with magnetic swipe standard
with optional proximity reader and/or keypad
Outside motorized ET trim
8800 Rim or 8900 Mortise Lock Exit Device
Inside escutcheon with circuit board and battery pack
6 “AA” alkaline batteries
Screw pack
8877/8878 x ET x Lever Design Passport 1000 Rim Exit Device
6
4
5
3
2
ITEM
PART No.
DESCRIPTION
REQ’D
1
--
Cylinder Assembly (Reference Catalog for Available Cylinders)
1
2
--
Lever (Reference Catalog for Available Styles)
1
3
97-4105
Exit Trim (ET) With Cylinder
1
97-4106
Exit Trim (ET) Without Cylinder
52-4845
Motor Assembly (Separate - not shown)
1
68-7255
Chassis Assembly
1
68-7256
Chassis Assembly (Fire Rated)
68-5836
Chassis Assembly (Latch Guarding)
4
68-5837
Chassis Assembly (Fire Rated Latch Guarding)
5
01-4451
1/4-20 x 2-3/8” ET Screws
2
6
01-2273
#10 x 1-1/4” Chassis Screws
4
01-1185
#10-24 x 3/4” Chassis Screws
4
7
97-0052
#8-32 x 5/16” Cover Screws
4
8
68-0406
Chassis Cover
1
68-1014
Chassis Cover (With Guarding)
5
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
1
Passport 1000 P2 WiFi Exit Device
Parts Breakdown (continued)
8977/8978 x RT x Lever Design Passport 1000 Mortise Exit Device
7
6
7
8
7
5
4
3
2
ITEM
PART No.
DESCRIPTION
REQ’D
1
--
Cylinder Assembly (Reference Catalog for Available Cylinders)
1
2
--
Lever (Reference Catalog for Available Styles)
1
3
97-4107
Exit Trim (ET) With Cylinder
1
97-4108
Exit Trim (ET) Without Cylinder
52-4845
Motor Assembly (Separate - not shown)
99-2401
8900 Lock Body Assembly LHR
99-2402
8900 Lock Body Assembly RHR
99-2403
8900 Lock Body Assembly LHR (Non-Beveled Door)
4
1
99-2404
8900 Lock Body Assembly RHR (Non-Beveled Door)
5
99-2628
Screw Pack
1
6
68-7253
Chassis Assembly LHR
1
Chassis Assembly RHR
68-2143
Screw Pack
1
8
68-0407
Chassis Cover
1
03/31/14
68-7254
7
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
1
6
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
6
Installation Instructions for 8877/8878 Rim Exit
1
Door Preparation
Inside
A. Verify Hand and Bevel of Door
• Check hand of door.
The exit device is non-handed and
the trim is field reversible.
Left Hand
Reverse
LHR
• Door should be fitted and hung.
B. Verify Product Label
Outside
Right Hand
Reverse
RHR
Fig. 1A
C. Door Preparation
1. If mullion is used, install prior to installing hardware.
2. Doors should be pre-prepped (recommended).
3. Use appropriate templates:
• Passport 1000 template A7951 (wood and metal).
• Exit installation instructions A6770.
Note: Instruction examples show wood door installation.
Inside of Door
Outside of Door
Through Bolt Holes
Through Bolt Holes
Door
Position
Switch
Through Bolt Holes
Through Bolt Holes
Wire Run Channel (Wood Door)
ET Through Bolt Hole
Cylinder Hole
Cylinder Hole
Trim Lever Hole
Lever Hole
Fig. 1B
ET Through Bolt Hole
03/31/14
ET Through Bolt Hole
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
For metal doors, route cables inside door.
7
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
2
Install Door Position Switch (DPS)
Wood doors have 3/8” raceway to controller cutout and metal doors
have 3/4” raceway to the controller cutout.
Refer to template A7951.
1. Insert connector end of DPS through the raceway on the latch edge
of the door (Fig. 2A).
Note: For metal doors, use DPS Collar.
2. Push DPS firmly into place by hand.
IMPORTANT: DO NOT TAP SWITCH WITH ANY TOOL.
Inside of Door
Collar is used only
with metal doors.
Door Position
Switch Hole
Dim 1
Door Position
Switch (DPS)
Vertical
of Strike
Wood Frame
3/4”
Horizontal
of Strike
Fig. 2B
3
Fig. 2A
Position Exit Trim (ET)
Outside of Door
For exterior applications, use ET gasket (52-0263) to seal
between ET escutcheon and outside door surface.
1. For wood doors: Route ET wire harness through the cylinder hole,
out the other side, and through the wire run channel to the
controller cutout.
For metal doors: Route ET wire harness
through the cylinder hole and door
and out the controller cutout.
ET Wire
Harness
(from motor)
ET Gasket
(Exterior Applications)
2. Position and hold ET trim on the door.
ET Control
Fig. 3
8
1-800-810-WIRE • www.sargentlock.com • A8012F
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
3/8”
03/31/14
Dim 1
Dim 2
(From template)
Metal Frame
Passport 1000 P2 WiFi Exit Device
4
Mount Exit Device Chassis
1. Position exit chassis carefully, verifying that the ET
spindle engages the lower hub of the exit chassis.
DO NOT PINCH THE WIRE HARNESS.
Inside of Door (Wood)
2. Secure the exit chassis with through bolts
to the ET trim using (2) 1/4 -20 x 2-3/8”
flat head machine screws.
3. For wood door applications, attach
ground harness (Fig. 4C) using the
top through-bolt screw.
ET Wire Harness
ET Wire Harness
Ground Harness (from
motor, wood doors only)
Put ground lug through
top flat head screw and
tighten down.
Inside of Door (Metal)
Fig. 4B
(2) 1/4 x 2-3/8”
Flathead Machine
Screws (secures ET)
Fig. 4A
5
Exit Chassis
Install Cylinder
For devices without cylinder, go to Step 6.
1. While installing the rim cylinder, support the tail piece of the cylinder,
verifying its engagement with the top hub of the exit chassis
Note: Be sure ET harness is clear of cylinder and tailpiece.
2. Secure the cylinder by through-bolting the cylinder
through the exit chassis using (2) #12-24 x 1-7/8”
connecting screws (see Fig. 5A).
3. Verify that the key retracts latchbolt.
Position cylinder so that the
SARGENT logo is right-side up.
Correct
Incorrect
Fig. 5A
Fig. 5B
9
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
Exit Chassis
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
(2) 1/4 x 2-3/8”
Flathead Machine
Screws (secures ET)
Passport 1000 P2 WiFi Exit Device
6
Secure Exit Chassis
To comply with UL certifications and
for security: Fasten exit chassis
to door using (4) #10 wood screws
(for wood door) or (4) #10-24
machine screws (for metal door).
Inside of Door
(4) #10 Wood Screws or
#10-24 Machine Screws
(2) #12-24 x 1-7/8”
Flat Head Screws
(Through-bolts
Cylinder to Chassis)
Fig. 6
Connect DPS to harness (Fig. 7A and 7B).
Mortise Lock Body
Connector and
Ring Terminal
Wood door shown
(collar used on metal door only)
Door Position Switch (DPS)
DPS (Door
Position Switch)
To Controller
Inside of Door
DPS
To Door
Position
Switch
To Lock Body
Fig. 7A
Fig. 7B
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
(4) #10 Wood Screws or
#10-24 Machine Screws
Connect Door Position Switch (DPS)
03/31/14
7
10
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
8
Install Chassis Cover
Secure chassis cover to chassis using
(4) #8-32 x 5/16” oval head machine
screws (Fig. 8).
Fig. 8
1. Position the wire cover plate above the
chassis cover and covering the wire channel.
Mark hole positions.
Note: Make sure stamped side of plate is against door.
2. Drill (2) 3/32” diameter by 1/2” deep holes (Fig. 9A).
3. Cover wires with cover plate by securing plate to
door directly above chassis (note orientation) using
two (2) #6 x 1/2” flat head security torx wood screws
(Fig. 9B).
Inside of door
Note: Position lower edge of cover plate against the
cover to ensure that no wires are visible.
Back Side of
Wire Cover Plate
Wire Cover
(2) #6 x 1/2” Flat
Head Security
Torx Wood Screws
(2) 3/32” Diameter by
1/2” Deep Holes
Fig. 9B Detail
Fig. 9A
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Install Wire Cover (Wood Doors Only)
03/31/14
9
This Side Down
11
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
10 Install Outside Escutcheon (with Optional Gasket)
Note: Gasket optional, for non-fire rated doors only.
For non-fire rated door applications, an optional gasket
(Part number 52-0782) may be used as a weather seal
between the escutcheon and the outside door surface.
Peel off adhesive backing and attach to (outside) escutcheon.
1. Position the outside escutcheon, aligning the posts
with the door prep (Fig. 10).
2. On the inside of the door, position the mounting plate
over the indicated holes.
3. Feed reader cable through opening.
4. The cable from the lockbody feeds from the bottom.
Fig. 10A
03/31/14
Fig. 10B
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Note: Cable lengths exaggerated for illustrative purposes.
12
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
11
Installation of Connectors
CAUTION - Do not touch or allow debris to enter connector contacts.
Secure the following connectors to their respective terminals (Fig. 11A, B ):
A. Secure the 10-pin lock body assembly connector.
DPS
Reader
(24-pin)
9-24VDC
Power*
*NOTE: Optional 2-pin external 12-24VDC power connector.
Mounting Plate
Board-to-Board
Connector
Fig. 11A
Lock
Body
(10-pin)
Reader
Cable
DPS
Position ground
ring terminal
upright, then
tighten screw
Fig. 11B
Lock body cable
Wire Positioning:
Please follow these steps prior to installing
inside escutcheon to prevent any damage
caused by pinching wires:
B. Tuck excess cable into wire hole on inside of door.
C. Finish securing mounting plate and reader to door by fully tightening through-bolts on inside of door.
Note: Ensure groundring is positioned upright.
D. Secure the 24-pin card reader connector.
13
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
Passport 1000 P2 WiFi Exit Device
12 Installing the Controller
1. Insert bottom tab of controller into slot on mounting plate (Fig. 12A, B).
2. Looking down from top of controller, ensure proper alignment of board-to-board connectors (Fig. 13B) while pivoting controller toward door until two tabs on top snap securely into place on mounting plate.
Board-to-Board
Connectors
Fig. 12A
Fig. 12B
Fig. 12B Detail
03/31/14
Fig. 12A Detail
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller.
14
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
13
Install Battery Pack
Before installing batteries for the first time:
Remove pull tab from its position beneath the coin cell by pulling
on tab in direction of arrows printed on tab (Fig. 13).
a. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly.
b. After batteries are installed, there is a slight delay; then the LED will flash amber and the lock motor will cycle.
For battery replacement:
When replacing the (6) “AA” alkaline batteries in the compartment,
please note batteries must be replaced within five (5) minutes to
prevent the internal clock from becoming inaccurate.
Inside of Door
Fig. 13
Install Inside Escutcheon
1. Position inside escutcheon as shown (Fig. 14).
Verify that all wires are positioned within the escutcheon
to avoid pinching.
2. Attach escutcheon with (2) #8-32 x 1/2” T-20 Torx pan
head screws.
3. Straighten escutcheon and tighten securely.
DO NOT OVERTIGHTEN.
(2) #8-32 x 1/2”
Torx Screws
Fig. 14
15
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
14
Passport 1000 P2 WiFi Exit Device
16 Installation of Rail Assembly
1. Retrieve harness from end of rail.
Note: Length of harness requires caution when handling to avoid damage. Harness
should not be stretched or overextended.
2. Attach harness to female connector on chassis.
3. Install rail and screws per exit device instructions.
Note: This view shows rim exit device version.
03/31/14
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Fig. 15`
16
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
Installation Instructions for Mortise Type 8977/8978 Exit Device
1
Door Preparation
Inside
A. Verify Hand and Bevel of Door
• Check hand of door.
This exit device is handed and is not reversible.
Left Hand
Reverse
LHR
• Door should be fitted and hung.
Outside
Right Hand
Reverse
RHR
Fig. 1A
B. Door Preparation
1. If using a mullion, install it prior to installing hardware.
2. Doors should be pre-prepped (recommended).
3. Use appropriate templates:
• Passport 1000 template A7952 (Field Prep Template).
• Exit installation instructions A6705.
Note: Instruction examples show wood door installation.
For metal doors, route cables inside door.
Outside of Door
Inside of Door
Through Bolt Hole
Through Bolt Hole
Door
Position
Switch
Wire Cutout
ET Through
Bolt Hole
Wire Run Channel (Wood Door)
Cylinder Hole
Lever Hole
Mortise
Pocket
ET Through
Bolt Hole
Fig. 1B
17
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
7
Passport 1000 P2 WiFi Exit Device
2
Install Door Position Switch (DPS)
Wood doors have 3/8” raceway to controller cutout and metal doors
have 3/4” raceway to the controller cutout.
Inside of Door
Refer to template A7951.
1. Insert connector end of DPS through the raceway
on the latch edge of the door (Fig.6A).
Note: For metal doors, use DPS Collar.
Collar is used only
with metal doors.
2. Push DPS firmly into place by hand.
IMPORTANT: DO NOT TAP SWITCH WITH ANY TOOL.
Door Position
Switch (DPS)
Door Position
Switch Hole
Dim 1
Vertical
of Strike
Dim 2
(From template)
Wood Frame
Dim 1
3/8”
Metal Frame
3/4”
Fig. 2A
3
Position Exit Trim (ET)
1. Slide mortise lock into door and loosely secure with (2) flat head screws.
Note: For exterior applications, use ET gasket (52-0263) to seal between ET trim and the door
surface.
2. For wood doors: Route ET wire harness through
the wire cutout, out the other side and through
the Wire Run Channel (on
the inside) to the Controller Cutout.
For metal doors: Route ET wire harness
through the wire cutout and door and
out the controller cutout.
3. Position the ET trim so the ET spindle
engages the mortise lock hub
and hold in place.
Wire Harness
(From motor)
ET Control
ET Control
Outside of Door
(2) 1/4” x 2-3/8”
Flat Head
Machine Screws
(Secures ET)
Fig. 3A
18
Mortise Lock Body
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
Fig. 2B
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Horizontal
of Strike
Passport 1000 P2 WiFi Exit Device
4
Mount Exit Device Chassis
1. Position exit chassis carefully, verifying the chassis lift lever engages the mortise lock (Fig. 4B).
DO NOT PINCH THE WIRE HARNESS.
2. Secure the exit chassis by through bolting to the ET trim with (2) 1/4 -20 x 2-3/8”
flat head machine screws.
3. For wood door applications, attach Ground Harness as shown in Fig. 2B, using the
top through-bolt screw
Mortise Lock Body
Connector and
Ring Terminal
Chassis
Lever
Latch Bolt
DPS (Door Position Switch)
Grounding Harness
(Wood doors only)
Chassis Lift Lever
Fig. 4B Detail
(2) 1/4” x 2-3/8” Flat Head
Machine Screws (Secures ET)
Fig. 4A
Wood Door
Exit Chassis
Secure Exit Chassis
Mortise Lock Body
Connector and
Ring Terminal
Fasten exit chassis to door using (4) #10
wood screws for wood door or (4) #10-24
machine screws for metal door (Fig. 5).
DPS (Door Position Switch)
(4) #10 Wood Screws
or #10-24 Machine Screws
Inside of Door
Fig. 5
19
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
5
Passport 1000 P2 WiFi Exit Device
6
Install Cylinder
For devices without cylinder, go to Step 7.
1. Slide cylinder through ET Trim and thread into
the lockbody, rotating the cylinder clockwise.
Outside of Door
Cylinder should rest flush on ET Case.
Note: SARGENT logo must be horizontal
and on the top of the cylinder (Fig. 6B).
2. Secure the cylinder by tightening cylinder
clamp screw located above the guardbolt.
3. Verify that the key retracts the latchbolt.
Position cylinder so that the
SARGENT logo is right-side up.
#46 Cylinder
Incorrect
Fig. 6B
Install Chassis Cover
Secure chassis cover to chassis using
(4) #8-32 x 5/16” oval head machine screws.
Inside of Door
Chassis Cover
(4) #8-32 x 5/8” Oval
Head Machine Screws
Fig. 7
03/31/14
7
Fig. 6A
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Correct
Set Screw
20
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
8
Install Wire Cover (Wood Doors Only)
1. Position the wire cover plate above the
chassis cover and covering the wire channel.
Mark hole positions.
Note: Make sure stamped side of plate is against door.
Inside of Door
2. Drill (2) 3/32” diameter by 1/2” deep holes (Fig. 8A).
3. Cover wires with cover plate by securing plate
to door directly above chassis (note orientation)
using two (2) #6 x 1/2” flat head security
torx wood screws (Fig. 8B).
Wire Cover
Note: Position lower edge of cover plate against the
cover to ensure that no wires are visible.
Back Side of
Wire Cover Plate
(2) #6 x 1/2”
Flat Head Security
Torx Wood Screws
(2) 3/32” Diameter by
1/2” Deep Holes
Fig. 8A
This Side Down
Install Outside Escutcheon (with Optional Gasket)
Note: Gasket optional, for non-fire rated doors only.
For non-fire rated door applications, an optional gasket
(Part number 52-0782) may be used as a weather seal
between the escutcheon and the outside door surface.
Peel off adhesive backing and attach to (outside) escutcheon.
1. Position the outside escutcheon, aligning the posts
with the door prep (Fig. 9).
2. On the inside of the door, position the mounting plate
over the indicated holes.
3. Feed reader cable through opening.
4. The cable from the lockbody feeds from the bottom.
Note: Cable lengths exaggerated for illustrative purposes.
Fig. 9
21
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
9
Fig. 8B Detail
Passport 1000 P2 WiFi Exit Device
Install Outside Escutcheon and Mounting Plate Assembly
1. Insert the mounting posts through holes as shown.
Mounting Plate
2. On the inside of the door, position the mounting plate over the
indicated holes (Fig. 10A).
3. Feed controller and keypad wires/cables
through side opening (Fig. 10B).
Ground wire routes through bottom of mounting plate.
4. Route ground ring terminal from lock body through bottom
of mounting plate and attach to to bottom right
corner using one #8-32 x 1-7/8” flat head machine screw.
Reader
Cable
Make sure it is positioned upright (Fig. 10B).
DPS
5. Insert other three #8-32 x 1-7/8” flat head machine
screws and tighten, fastening the outside escutcheon
to the door (Fig. 10B).
6. Attach two (2) #8 x 3/8” flat head wood screws for wood
doors or (2) #8-32 x 3/8” flat head machine screws
for metal doors (Fig. 10C).
Reader
(24-pin)
Board-to-Board
Connector
Position
ground ring
terminal
upright, then
tighten screw
Fig. 10B
Lock body
cable
9-24VDC
Power*
Fig. 10A
Lock Body
(10-pin)
Fig. 10C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
IMPORTANT: If the following step is skipped, the product
will not be UL-compliant:
03/31/14
10
22
1-800-810-WIRE • www.sargentlock.com • A8012F
Passport 1000 P2 WiFi Exit Device
11 Installing the Controller
1. Insert bottom tab of controller into slot on mounting plate (Fig. 11A, B).
2. Looking down from top of controller, ensure proper alignment of board-to-board connectors (Fig. 11B) while pivoting controller toward door until two tabs on top snap securely into place on mounting plate.
CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller.
Board-to-Board
Connectors
Fig. 11A
Fig. 11B
Fig. 11B Detail
23
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
Fig. 11A
Detail
Passport 1000 P2 WiFi Exit Device
12
Install Battery Pack
Before installing batteries for the first time:
Remove pull tab from its position beneath the coin cell by pulling
on tab in direction of arrows printed on tab (Fig. 12).
a. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly.
Inside of Door
b. After batteries are installed, there is a slight delay; then the LED will flash amber and the lock motor will cycle.
For battery replacement:
13
Install Inside Escutcheon
1. Position inside escutcheon as shown (Fig. 13).
Verify that all wires are positioned within the escutcheon
to avoid pinching.
2. Attach escutcheon with (2) #8-32 x 1/2” T-20 Torx pan
head screws.
3. Straighten escutcheon and tighten securely.
DO NOT OVERTIGHTEN.
(2) #8-32 x 1/2”
Torx Screws
Fig. 13
24
1-800-810-WIRE • www.sargentlock.com • A8012F
03/31/14
Fig. 12
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
When replacing the (6) “AA” alkaline batteries in the compartment,
please note batteries must be replaced within five (5) minutes to
prevent the internal clock from becoming inaccurate.
Passport 1000 P2 WiFi Exit Device
14 Installation of Rail Assembly
1. Retrieve harness from end of rail.
Note: Harness has limited travel and can be damaged.
2. Attach harness to female connector on chassis.
3. Install rail and screws per exit device instructions.
Note: This view shows rim exit device version.
Fig. 14
Operational Check
IMPORTANT: Be sure to test functions prior to closing door.
In all cases, perform the following checks:
• For units with cylinders, the following checks apply:
Insert key into cylinder and rotate:
a. There should be no friction against lock case or any other
obstructions. If friction or binding occurs, readjust cylinder to
eliminate issues.
b. The key should retract the latch and the key should rotate
freely.
• For units without a keypad, add card using LCT
software and test.
• For units with a keypad, add pin and card using LCT software and
test.
2. LED signaling:
• After using a valid credential, a green flash followed by three fast
amber flashes indicates a low power condition.
Check the battery voltage.
If the voltage is low, replace the batteries.
• If the lock loses power, it will flash rapid amber for approximately
one minute. Lock will default to programmed fail safe or fail secure.
After that, the lock will no longer be functional.
3. When you have completed the tests, close the door, ensuring latchbolt and deadbolt fully extend into strike plate without binding.
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
1. Ensure that inside lever retracts latch.
03/31/14
8
25
1-800-810-WIRE • www.sargentlock.com • A8012F
SARGENT Manufacturing
100 Sargent Drive
New Haven, CT 06511 USA
1-800-810-WIRE (9473) • www.sargentlock.com
Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,
electro-mechanical products and access control systems for new construction, renovation, and replacement applications.
The company’s customer base includes commercial construction, institutional, and industrial markets.
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
ASSA ABLOY is the global leader in door opening solutions, dedicated to
satisfying end-user needs for security, safety and convenience.
A8012F-03/14