PARTS AND OPERATION MANUAL
PARTS AND OPERATION MANUAL
© COPYRIGHT 2001, MULTIQUIP INC.
MQ POWER
DCA-40SSI
TM
WHISPERWATT
GENERATOR
PARTS LIST NO. 8051204
FINAL COPY
MULTIQUIP INC..
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
SERVICE DEPARTMENT:
800-421-1244
800-835-2551
FAX: 310-537-3927
FAX: 310-638-8046
E-mail:mq@multiquip.com • www:multiquip.com
PAGE 2 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 3
TABLE OF CONTENTS
Here's How To Get Help ................................................... 3
Table Of Contents ............................................................ 4
Parts Ordering Procedures .............................................. 5
Rules for Safe Operation .............................................. 6-9
Towing and Transportation ............................................. 10
Trailer Safety Guidelines ........................................... 11-17
Trailer Wiring Diagram .................................................... 18
Electric Brake Troubleshooting ...................................... 19
Hydraulic Brake Troubleshooting .................................... 20
Operation and Safety Decals .................................... 21-22
DCA-40SSI Specifications ............................................ 23
General Information ....................................................... 24
Major Components ........................................................ 25
Dimensions ............................................................... 26-27
Control Panel Descriptions ....................................... 28-29
Engine Operating Panel Descriptions ....................... 30-31
Output Terminal Panel Description ............................ 32-33
Output Amperage Setup ........................................... 34-35
Output Voltage Setup ................................................ 36-39
Installation ................................................................ 40-41
Pre Setup ................................................................. 42-45
Load Application ............................................................ 46
Generator Start-up Procedure .................................. 47-49
Generator Shutdown Procedure ..................................... 50
Maintenance ............................................................. 52-55
Engine Wiring Diagram ............................................. 56-57
Generator Wiring Diagram .............................................. 58
Engine Troubleshooting ............................................. 60-61
Generator/Engine Troubleshooting ................................. 62
Explanation of Codes in Remarks Column .................... 64
Suggested Spare Parts ................................................. 65
MQ POWER DCA-40SSI
AC GENERATOR
Generator Assembly .................................................66-67
Control Box Assembly ..............................................68-71
Engine & Radiator Assembly ....................................72-73
Engine Operating Panel Assembly ...........................74-75
Output Terminal Assembly ........................................76-77
Battery Assembly .....................................................78-79
Muffler Assembly .....................................................80-81
Fuel Tank Assembly .................................................82-83
Enclosure Assembly ................................................84-87
Rubber Seal Assembly .............................................88-89
Name Plate And Decals ...........................................90-91
ISUZU 4BG1 ENGINE
Cylinder Head Cover Assembly ................................92-93
Cylinder Head Assembly ..........................................94-95
Cylinder Block Assembly .........................................96-97
Oil Pan and Level Gauge Assembly .........................98-99
Camshaft and Valve Assembly .............................. 100-101
Crankshaft, Piston and Flywheel Assembly .......... 102-103
Timing Gear and Flywheel Housing Assembly ...... 104-105
Engine Mounting Assembly ................................... 106-107
Inlet Manifold Assembly ........................................ 108-109
Exhaust Manifold Assembly .................................. 110-111
Ventilation Assembly ............................................. 112-113
Water Pump and Corrosion Resistor Assembly ..... 114-115
Thermostat and Housing Assembly ...................... 116-117
Engine Water Piping Assembly .............................. 118-119
Fan and Fan Belt Assembly .................................. 120-121
Fuel Injection Assembly ........................................ 122-123
Fuel Filter and Bracket Assembly ......................... 124-125
Fuel Pump and Piping Assembly .......................... 126-127
Oil Cooler and Oil Filter Assembly ........................ 128-129
Oil Pump and Oil Strainer Assembly ..................... 130-131
Oil and Vacuum Piping Assembly ......................... 132-133
Electrical Control Assembly .................................. 134-135
Battery Relay Assembly ........................................ 136-137
Starter Component Assembly ............................... 138-139
Inj. Pump Component Assembly ........................... 140-143
Governor Component Assembly ............................ 144-147
Feed Pump Assembly ........................................... 148-149
Misc. Inj. Pump Assembly ..................................... 150-151
Coupling Assembly ................................................ 152-153
Accelerator Pedal Assembly ................................. 154-155
Air Duct Assembly ................................................ 156-157
Water Sedimenter Assembly ................................. 158-159
Clutch Assembly ................................................... 160-161
Switch and Relay Assembly .................................. 162-163
Terms and Condition of Sale — Parts ....................... 164
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
PARTS ORDERING PROCEDURES
■
■
■
■
■
■
■
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
•
•
•
•
UPS Ground
UPS Second Day or Third Day*
UPS Next Day*
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
•
Airborne Express*
Truck or parcel post
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
1-9 items
Additional Discount
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
■ UPS Ground Service at no charge for freight
■ PS Third Day Service at one-half of actual freight cost
No other allowances on freight shipped by any other carrier.
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
*DISCOUNTS ARE SUBJECT TO CHANGE*
ount
c
s
i
D
Fax
Extra
c USA
i
t
s
e
m
for Do
ly
rs On
e
l
a
e
D
UPS l
Specia
nly
ders o
xed or
For fa
Now! Direct TOLL-FREE access
to our Parts Department!
Toll-free nationwide:
800-421-1244
Toll-free FAX:
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 5
RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!
This equipment is to be operated by trained
and qualified personnel only! This equipment
is for industrial use only.
■ NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or generator.
The following safety guidelines should always be used when ■ High Temperatures – Allow the engine to cool before
operating the DCA-40SSI portable generator:
adding fuel or performing service and maintenance
GENERAL SAFETY
functions. Contact with hot components can cause serious
burns.
■ DO NOT operate or service this equipment before
reading this entire manual.
■ The engine of this generator requires an adequate free
flow of cooling air. Never operate the generator in any
■ This equipment should not be operated by
enclosed or narrow area where free flow of the air is
persons under 18 years of age.
restricted. If the air flow is restricted it will cause serious
damage to the generator or engine and may cause injury
to people. The generator engine gives off DEADLY carbon
■ NEVER operate this equipment without proper
monoxide gas.
protective clothing, shatterproof glasses, steeltoed boots and other protective devices
CAUTION
CAUTION:
required by the job.
■ Always refuel in a well-ventilated area,
away from sparks and open flames.
■ NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■ NEVER operate this equipment under the
influence or drugs or alcohol.
■ NEVER use accessories or attachments, which are not
recommended by MQ Power for this equipment. Damage
to the equipment and/or injury to user may result.
■ Manufacturer does not assume responsibility for any
accident due to equipment modifications.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ Always check the machine for loosened threads or bolts
before starting.
■ Always use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it
to cool. DO NOT smoke around or near
the machine. Fire or explosion could
result from fuel vapors, or if fuel is spilled
on a hot engine.
■
NEVER operate the generator in an
explosive atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
■
Topping-off to filler port is
dangerous, as it tends to spill fuel.
PAGE 6 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
RULES FOR SAFE OPERATION
CAUTION
CAUTION:
CAUTION
CAUTION:
DO NOT touch or open any of the below
mentioned components while the
generator is running. Always allow
sufficient time for the engine and generator
to cool before performing maintenance.
■ NEVER touch output terminals during operation. This is
extremely dangerous. Always stop the machine when
contact with the output terminals is required.
CAUTION
CAUTION:
■ Backfeed to a utility system can cause electrocution
and.or property damage. Do not connect to any
building's electrical system except through an approved
device or after building main switch is opened.
Radiator
1. Radiator Cap - Removing the radiator cap while the
engine is hot will result in high pressurized, boiling water
to gush out of the radiator, causing severe scalding to
any persons in the general area of the generator.
2. Coolant Drain Plug - Removing the coolant drain plug
while the engine is hot will result in hot coolant to gush
out of the coolant drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
3. Engine Oil Drain Plug - Removing the engine oil drain
plug while the engine is hot will result in hot oil to gush
out of the oil drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
CAUTION
CAUTION:
Never use damaged or worn cables when
connecting power tools or equipment to the
generator. Make sure power connecting
cables are securely connected to the
generator’s output terminals, insufficient
tightening of the terminal connections may
cause damage to the generator and
electrical shock.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 7
RULES FOR SAFE OPERATION
■ NEVER Run engine without air filter. Severe engine
damage may occur.
Battery
CAUTION
CAUTION:
Never over fill the battery with water above
the upper limit.
The battery contains acids that can cause injury to the eyes
and skin. To avoid eye irritation, always wear safety glasses.
Use well insulated gloves when picking up the battery. Use
the following guidelines when handling the battery:
■ Always service air cleaner frequently to prevent carburetor
malfunction.
■ Always disconnect the battery before performing service
on the generator.
■ Always be sure the operator is familiar with proper safety
precautions and operations techniques before using
generator.
■ Always store equipment properly when not in use.
Equipment should be stored in a clean, dry location out of
the reach of children.
■ DO NOT leave the generator running in the manual mode
unattended.
■ DO NOT allow unauthorized people to operate this
equipment.
1. DO NOT drop the battery. There is the possibility of risk
that the battery may explode.
■ Always read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
2. DO NOT expose the battery to open flames, sparks,
cigarettes etc. The battery contains combustible gases
and liquids. If these gases and liquids come in contact
with a flame or spark, an explosion could occur.
■ Refer to the Isuzu Engine Owner's Manual for engine
technical questions or information.
3. Always keep the battery charged. If the battery is not
charged a buildup of combustible gas will occur.
4. Always keep battery charging and booster cables in good
working condition. Repair or replace all worn cables.
5. Always recharge the battery in an open air environment,
to avoid risk of a dangerous concentration of combustible
gases.
6. In case the battery liquid (dilute sulfuric acid) comes in
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
7. In case the battery liquid (dilute sulfuric acid) comes in
contact with your eyes, rinse eyes immediately with
plenty of water, then contact the nearest doctor or hospital,
and seek medical attention.
Loading and Unloading (Crane)
■ Before lifting, make sure the generator's lifting hook is
secure and that there is no apparent damage to the
generator itself (loose screws, nuts and bolts). If any
part is loose or damaged, please take corrective action
before lifting.
■ Always drain fuel prior to lifting.
■ Always make sure crane or lifting device has been
properly secured to the hook of guard frame on generator.
■ NEVER lift the machine while the engine is running.
■ Use adequate lifting cable (wire or rope) of sufficient
strength.
■ When lifting the generator, always use the balanced
center-point suspension hook and lift straight upwards.
■ NEVER allow any person or animal to stand underneath
the machine while lifting.
■ When loading the generator on a truck, be sure to use
the front and back frame bars as a means to secure the
generator during transport.
PAGE 8 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
RULES FOR SAFE OPERATION
Transporting
■ Always shutdown engine before transporting.
■ Tighten fuel tank cap securely.
■ Drain fuel when transporting generator over long distances
or bad roads.
■ Always tie-down the generator during transportation by
securing the generator.
■ If generator is mounted on a trailer, make sure trailer
complies with all local and state safety transportation
laws. See page 10 for basic towing procedures.
Maintenance Safety
■ NEVER lubricate components or attempt service on a
running machine.
■ Always allow the machine a proper amount of time to
cool before servicing.
■ Keep the machinery in proper running condition.
■ Fix damage to the machine immediately and always
replace broken parts.
Emergencies
■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, coolant,
fuel, and fuel filters.
■ Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department.
■ DO NOT pour waste, oil, coolant or fuel directly onto the
ground, down a drain or into any water source.
■ DO NOT use plastic containers to dispose of hazardous
waste.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 9
DCA-40SSI — TOWING RULES FOR SAFE OPERATION
Towing Safety Precautions
CAUTION :
Check with your county or state safety
towing regulations department before towing
your generator.
To reduce the possibility of an accident
while transporting the generator on public roads, always
make sure the trailer (Figure 1) that supports the generator
and the towing vehicle are in good operating condition and
both units are mechanically sound.
The following list of suggestions should be used when towing
your generator:
■ Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating" (GVWR).
■ ALWAYS inspect the hitch and coupling for wear. NEVER
tow a trailer with defective hitches, couplings, chains
etc.
■ Check the tire air pressure on both towing vehicle and
trailer. Also check the tire tread wear on both vehicles.
■ ALWAYS make sure the trailer is equipped with a "Safety
Chain".
■ ALWAYS attach trailer’s safety chain to bumper of towing
vehicle.
■ ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and
working properly.
■ The maximum speed for highway towing is 45 MPH
unless posted otherwise. Recommended off-road towing
is not to exceed 10 MPH or less depending on type of
terrain.
■ Place chocked blocks underneath wheel to prevent
rolling, while parked.
■ Place support blocks underneath the trailer’s bumper to
prevent tipping, while parked.
■ Use the trailer’s hand winch to adjust the height of the
trailer, then insert locking pin to lock wheel stand in place,
while parked.
■ Avoid sudden stops and starts. This can cause skidding,
or jackknifing. Smooth, gradual starts and stops will
improve gas milage.
■ Avoid sharp turns to prevent rolling.
■ Remove wheel stand when transporting.
■ DO NOT transport generator with fuel in tank.
Figure 1. Generator with Trailer
PAGE 10 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — TRAILER-SAFETY GUIDELINES
CAUTION:
ALWAYS make sure the trailer is in good
operating condition. Check the tires for
proper inflation and wear. Also check the
wheel lug nuts for proper tightness.
Explanation of Chart:
This section is to provide the user with trailer service and
maintenance information. The service and maintenance
guidelines referenced in this section apply a wide range of
trailers. Remember periodic inspection of the trailer will ensure safe towing of the equipment and will prevent damage
to the equipment and personal injury.
It is the purpose of this section to cover the major maintenance components of the trailer. The following trailer components will be discussed in this section:
„
„
„
„
„
„
Brakes
Tires
Lug Nut Torquing
Suspension
Electrical
Brake Troubleshooting Tables
Use the following definitions with reading Table 1.
1. Fuel Cell - Provides an adequate amount of fuel for the
equipment in use. Fuel cells must be empty when transporting equipment.
2. Braking System - System employed in stopping the
trailer. Typical braking systems are electric, surge, hydraulic, hydraulic-surge and air.
3. GVWR- Gross Vehicle Weight Rating (GVWR), is the
maximum number of pounds the trailer can carry, including the fuel cell (empty).
4.
Frame Length - This measurement is from the ball
hitch to the rear bumper (reflector).
5. Frame Width - This measurement is from fender to
fender.
6.
Jack Stand - Trailer support device with maximum
pound requirement from the tongue of the trailer.
7. Coupler - Type of hitch used on the trailer for towing.
8. Tire Size - Indicates the diameter of the tire in inches
(10,12,14, etc.), and the width in millimeters
(175,185,205, etc.). The tire diameter must match the
diameter of the tire rim.
9. Tire Ply - The tire ply (layers) number is rated in letters;
2-ply,4-ply,6-ply, etc.
10. Wheel Hub - The wheel hub is connected to the trailer’s
axle.
11. Tire Rim - Tires mounted on a tire rim. The tire rim must
match the size of the tire.
12. Lug Nuts - Used to secure the wheel to the wheel hub.
Always use a torque wrench to tighten down the lug
nuts. See Table 4 and Figure 5 or lug nut tightening and
sequence.
13. Axle - Indicates the maximum weight the axle can support in pounds, and the diameter of the axle expressed
in inches (see Table 3). Please not that some trailers
have a double axle. This will be shown as 2-6000 lbs.,
meaning two axles with a total weight capacity of 6000
pounds.
14. Suspension - Protects the trailer chassis from shocks
transmitted through the wheels. Types of suspension
used are leaf, Q-flex, and air ride.
15. Electrical - Electrical connectors (looms) are provided
with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.
16. Application - Indicates which units can be employed
on a particular trailer.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 11
DCA-40SSI —TRAILER-SPECIFICATIONS
Table 1. Specifications
MODEL
APPLICATION
FU E L
C E LL
BRAKE
SYSTEM
GVWR
FRAME
LENGTH
FRAME
WIDTH
JACK
STAND
TRLR-10W
SDW225,
SGW250,TLW300
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10
DCA10, TLG12,
DCA-15
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10XF
DCA10, TLG-12,
DCA15, TLW-300
52 GAL
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-225W
WELDERS,
D A 7000S S
NO
NO
2200LB S
85"
42"
800LB .
FULL TILT WHEEL
TRLR-BLW400
BLW-400
NO
ELECTRIC
2700LB S
W/MAST 154"
W/O 124"
55"
(78" TALL)
800LB .
FULL TILT WHEEL
TRLR-50X
DCA-25
NO
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-50XF
DCA-25
41 GAL
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-70W
DCA-45, -60, 70
NO
SURGE
7000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-70X
DCA-45, -60, 70
OPT
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-70XF
DCA-45, -60, 70
53 GAL
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-100XF
DCA-100, 125
150 GAL
HYDRAULIC SURGE
7000LB S
190"
76"
2000LB .
FLAT PAD
TRLR-85/125
DCA-85, 100,
125
145 GAL
HYDRAULIC
10000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-150XF
DCA-150, 180
200 GAL
HYDRAULIC SURGE
11160LBS
204"
84"
5000 LB .
FLAT PAD
TRLR-220XF
DCA-220
250 GAL
HYDRAULIC SURGE
14000LB S
222"
83"
5000 LB .
FLAT PAD
TRLR-300XF
DCA-300
250 GAL
HYDRAULIC SURGE
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-400XF
DCA-400
350 GAL
ELECTRIC
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-600XF
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
TRLR-800SX
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
PAGE 12 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI —TRAILER-SPECIFICATIONS
Table 1. Specifications (Con't)
MODEL
COUPLER
TIRES
WHEELS
AXLE
HUBS SUSPENSION
ELECTRICAL
TRLR-10W
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.50"
2200# 2X 2
5 LUG
3 LE A F
4 WIRE LOOM W/
4 POLE FLAT
TRLR-10
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-10XF
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-225W
2" B A LL C LA S S
2 ADJUSTABLE
175-13B
13X4.5"
2200#2X 2
5 LUG
Q F LE X
4 POLE FLAT
TRLR-BLW
400
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13 X 4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-50X
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-50XF
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-70W
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70X
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70XF
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-100XF
ADJUSTABLE 2-5/6
OPT 3" EYE
205-15C
BIAS (4)
14"X5.5"
3500lbs
3"
5 LUG
5 LE A F
4 WIRE LOOM
TRLR-85/125
ADJUSTABLE 2-5/6
OPT 3" EYE
ST225/75R15D
RADIAL (4)
14"x6"
(2)-6000lbs
6 LUG
7 LE A F
4 WIRE LOOM
TRLR-150XF
3" BALL EYE
750-16 E
BIAS (4)
16" X 7"
(2)-6000lbs
8 LUG
7 LE A F
4 WIRE LOOM
TRLR-220XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(4)
16" X 7"
(2)-7000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-300XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(2)-6000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-400XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(3)-7000lbs.
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-600XF
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
7 LE A F
6 WIRE LOOM
TRLR-800AR
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
AIR-RIDE
6 WIRE LOOM
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 13
DCA-40SSI —TRAILER SAFETY GUIDELINES
Brakes
If your trailer has a braking system, the brakes should be
inspected the first 200 miles of operation. This will allow
the brake shoes and drums to seat properly. After the first
200 mile interval, inspect the brakes every 3,000 miles. If
driving over rough terrain, inspect the brakes more
frequently.
Electric Brakes
Electrically actuated brakes (Figure 2) are similar to
hydraulic brakes. The basic difference is that hydraulic
brakes are actuated by an electromagnet.
Listed below are some of the advantages that electric
brakes have over hydraulic brakes:
„ Brake system can be manually adjusted to provide
the corrected braking capability for varying road and
load conditions
„ Brake system can be modulated to provide more or
less braking force, thus easing the brake load on the
towing vehicle
„ Brake system has very little lag time between the time
the vehicle’s brakes are actuated and the trailer’s brakes
are actuated
„ Brake system can provide an independent emergency
brake system
Remember in order to properly synchronize the tow vehicle’s
braking to the trailer’s braking, can only be accomplished
by road testing. Brake lockup, grabbiness or harshness is
due to lack of synchronization between the tow vehicle
and the trailer being towed or under-adjusted brakes.
Before any brake synchronizations adjustments can be
made, the trailer brakes should be burnished-in by applying
the brakes 20-30 times with approximately a 20 m.p.h.
decrease in speed, e.g. 40 m.p.h. to 20 m.p.h. Allow ample
time for brakes to cool between application. This allows
the brake shoes to slightly be seated into the brake drum
surface.
Figure 2 displays the major electric brake components that
will require inspection and maintenance. Please inspect
these components as required.
Electric Brake Adjustment
1. Place the trailer on jack stands. Make sure the jack
stands are placed on secure level ground.
2. Check the wheel and drum for free rotation.
3. Remove the adjusting hole cover from the adjusting
slot at the bottom brake backing plate.
4. With a screwdriver or standard adjusting tool, rotate
the star wheel of the adjuster assembly to expand the
brake shoes.
5. Adjust the brake shoes outward until the pressure of
the lining against the wheel drum makes the wheel
difficult to turn.
6. Rotate the star wheel in the opposite direction until the
wheel rotates freely with slight lining drag.
7. Replace the adjusting hole cover and lower the trailer
to the ground.
8. Repeat steps 1 through 6 on the remaining brakes.
PAGE 14 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — TRAILER SAFETY GUIDELINES
Figure 2. Electrical Brake Components
Hydraulic/Air/Surge Brakes
Hydraulic brakes (Figure 3) should not require any special
attention with the exception of routine maintenance such
as shoe and lining replacement. These brakes can be
adjusted in the same manner as electric brakes. Brake
lines should be periodically checked for cracks, kinks, or
blockage.
Figure 3 below displays the major hydraulic/air/surge brake
components that will require inspection and maintenance.
Please inspect these components as required using steps
1 through 6 as referenced in the electric brake adjustments
section.
Figure 3. Hydraulic Brake Components
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 15
DCA-40SSI — TRAILER SAFETY GUIDELINES
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
CAUTION:
DO NOT attempt to repair or modify a
wheel. DO NOT install in inner tube to
correct a leak through the rim. If the rim
is cracked, the
air pressure in
the inner tube
may cause pieces of the rim to
explode (break off) with great force
and cause serious eye or bodily
injury.
Tire Wear/Inflation
Tire inflation pressure is the most important factor in tire life.
Pressure should be checked cold before operation DO NOT
bleed air from tires when they are hot. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 2 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
Suspension
The leaf suspension springs and associated components
(Figure 4) should be visually inspected every 6,000 miles for
signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts
(suspension) immediately. Torqued suspension components
as detailed in Table 3.
CAUTION:
NOTE
ALWAYS wear safety glasses when removing
or installing force fitted parts. Failure to comply
may result in serious injury.
Figure 4. Major Suspension Components
PAGE 16 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI —TRAILER SAFETY GUIDELINES
Table 3. Suspension Torque Requirements
Item
Torque (Ft.-Lbs.)
3/8" U-BOLT
MIN-30 MAX-35
7/16" U-BOLT
MIN-45 MAX-60
1/2" U-BOLT
MIN-45 MAX-60
SHACKLE BOLT
SNUG FIT ONLY. PARTS MUST ROTATE FREELY.
SPRING EYE BOLT
LOCKING NUTS OR COTTER PINS ARE PROVIDED TO
RETAIN NUT-BOLT ASSEMBLY.
MIN-30 MAX-50
SHOULDER TYPE
SHACKLE BOLT
Lug Nut Torque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 5. DO NOT
torque the wheel lug nuts all the way down. Tighten
each lug nut in 3 separate passes as defined by Table 4.
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 4. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
20-25
35-40
50-65
13"
20-25
35-40
50-65
14"
20-25
50-60
90-120
15"
20-25
50-60
90-120
16"
20-25
50-60
90-120
Figure 5. Wheel Lug Nuts Tightening Sequence
NOTE
NEVER use an pneumatic air gun to
tighten wheel lug nuts.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 17
DCA-40SSI —TRAILER-WIRING DIAGRAM
NOTE:
LIGHTS ARE ORIENTED FROM THE DRIVER’S SEAT
PAGE 18 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI —TRAILER-BRAKE TROUBLESHOOTING
Table 5. Electric Brake Troubleshooting
Symptom
Possible Cause
Solution
No Brakes or Intermittent Brakes
Any open circuits or broken wires?
Find and correct.
Any shor t circuits?
Find and correct.
Faulty controller?
Test and correct.
Any loose connections?
Find and repair.
Ground wire secure?
Find and secure.
Grease or oil on magnets or linings?
Clean or replace.
Connections corroded?
Clean and correct cause
of corrosion.
Brake drums scored or grooved?
Machine or replace.
Brakes synchronized?
Correct.
Brake components loose, bent or broken?
Replace components.
Brake drums out-of-round?
Replace.
System lubricated?
Lubricate.
Brake components correct?
Replace and correct.
Bearings of the wheel adjusted?
Adjust.
Weak Brakes or Brakes Pull to
One Side
Locking Brakes
Noisy Brakes
Dragging Brakes
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 19
DCA-40SSI —TRAILER-BRAKE TROUBLESHOOTING
Table 6. Hydraulic Brake Troubleshooting
Symptom
Possible Cause
Solution
No Brakes
Brake line broken or kinked?
Repair or replace.
Weak Brakes or Brakes Pull to
One Side
Brake lining glazed?
Reburnish or replace.
Trailer overloaded?
Correct weight.
Brake drums scored or grooved?
Machine or replace.
Tire pressure correct?
Inflate all tires equally.
Tires unmatched on the same axle?
Match tires.
Brake components loose, bent or broken?
Replace components.
Brake drums out-of-round?
Replace.
System lubricated?
Lubricate.
Brake components correct?
Replace and correct.
Brake lining thickness correct or in right
wrong position?
Install new shoes and
linings.
Enough brake fluid or correct fluid?
Replace rubber par ts
fill with dot4 fluid.
Locking Brakes
Noisy Brakes
Dragging Brakes
PAGE 20 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — GENERATOR DECALS
The DCA-40SSI generator is equipped with a number of safety decals. These decals are provided for operator safety and
maintenance information. The illustration below and on the preceding page show the decals as they appear on the
machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 21
DCA-40SSI — GENERATOR DECALS
PAGE 22 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — SPECIFICATIONS
Table 7. Specifications
Generator Specifications
Model
DCA-40SSI
Type
Revolving field, self ventilated, open protected type synchronous
generator
Armature Connection
Star with Neutral
Zig Zag
Phase
3
Single
Standby Output
47.7 KVA (38.2 KW)
27.6 KW
Prime Output
45 KVA (36 KW)
26 KW
Voltage
240V or 480V
240/120V
Frequency
60 Hz
Speed
1800 r pm
Power Factor
0.8
1
Aux. AC Power
Single Phase, 60 Hz
Voltage
120 V
Output
4.8 KW (2.4 KW x 2)
Engine Specifications
Model
ISUZU 4BD1
Type
4 Cycle, water-cooled, direct injection
No. of Cylinders
4 cylinders
Bore x Stroke
4.13 in. x 4.92 in. (105 mm x 125 mm)
Rated Output
55.2 HP/1800 rpm
Displacement
268 cu. in. (4392 cc)
Star ting
Electric
Coolant Capacity
5.3 gal. (20 liters)
Lube Oil Capacity
3.4 gal. (12.9 liters)
2.7 gal. (10.3L)/hr at full load
2.0 gal. (7.6L)/hr at 3/4 load
1.5 gal. (5.7L)/hr at 1/2 load
1.1 gal. (4.2L)/hr at 1/4 load
Fuel Consumption
Battery
12V- 100AH
Fu e l
#2 Diesel Fuel
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 23
DCA-40SSI — GENERAL INFORMATION
DCA-40SSI FAMILIARIZATION
Open Delta Excitation System
Generator
The DCA-40SSI generator is equipped with the state of the
The MQ Power Model DCA-40SSI is a 26 kW generator art "Open-Delta" excitation system. The open delta system
that is designed as a high quality portable (requires a trailer consist of an electrically independent winding wound among
for transport) power source for telecom sites, lighting stationary windings of the AC output section.
facilities, power tools, submersible pumps and other There are four leads: A, B, C and D. During light loads, the
industrial and construction machinery.
power to the Automatic Voltage Regulator (AVR) is supplied
from the leads parallel connections of B&C. When loads
Engine Operating Panel
increase, the AVR switches and accepts power from leads
The “Engine Operating Panel” is provided with the following: A&D. The output of leads A&D increase proportionally with
z Tachometer
load. This of adding the voltages to each phase provides
z Water Temperature Gauge
better voltage response during heavy loads.
z Oil Pressure Gauge
The connections of the AVR to the AC output windings are
z Charging Ammeter Gauge
for sensing only. No power is required from these windings.
z Fuel level gauge
z Engine Speed Control
The open-delta design provides virtually unlimited excitation
z Pre-Heat Button
current, offering maximum motor starting capabilities. The
z Panel Light
excitation does not have a "fixed ceiling" and responds
z Panel Light Switch
according the demands of the required load.
z Starter /Preheat Switch
Generator Control Panel
Engine
The “Generator Control Panel” is provided with the following:
The DCA-40SSI is powered by a 4 cycle, water cooled,
z Output Voltage Adjustment Knob
turbocharged Isuzu 4BG1 diesel engine. This engine is
z Frequency Meter (Hz)
designed to meet every performance requirement for the
z AC Ammeter (Amps)
generator. Reference Table 7, page 23 for engine
z AC Voltmeter (Volts)
specifications.
z Ammeter Change-Over Switch
In keeping with Multiquip's policy of constantly improving
z Voltmeter Change-Over Switch
its products, the specifications quoted herein are subject to
z Voltage Regulator
change without prior notice.
Output Terminal Panel
The basic controls and indicators for the DCA-40SSI
The “Output Terminal Panel” is provided with the following: generator are addressed on the following pages.
z
z
z
z
Three 120/240V output receptacles, 50 amp
Two 120V input receptacles, 20 amp
3 Load Circuit Breakers 240/120V @50 amps
2 Load GFCI Circuit Breakers 120V@ 20amps
Control Box
The “Control Box” is provided with the following:
z Main Circuit Breaker 110 amps
z Over-Current Relay
Mechanical Governor System
The mechanical governor system control the RPM of the
engine. When the engine demands increase or decrease,
the mechanical governor system regulates the frequency
variation to ±1.5%. The electronic governor option increases frequency variation to ±.25%.
PAGE 24 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — MAJOR COMPONENTS
Figure 6. Major Components
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 25
DCA-40SSI — DIMENSIONS (SIDE AND BACK)
Figure 7a. Dimensions
PAGE 26 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — DIMENSIONS (TOP AND FRONT)
Figure 7b. Dimensions
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 27
DCA-40SSI — CONTROL PANEL
Figure 8. Control Panel
PAGE 28 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — CONTROL PANEL
The definitions below describe the controls and functions of
the DCA-40SSI " Control Panel " (Figure 8).
1.
Main Circuit Breaker – This three-pole, 110 amp main
breaker is provided to protect the UNV voltage output
terminals from overload.
2.
AC Ammeter – Indicates the amount of current the
load is drawing from the generator.
3.
Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 60 Hz ±1 Hz .
4.
AC Voltmeter – Indicates the single phase output
voltage present at the UNV terminals.
5.
Voltage Regulator Control – Allows manual
adjustment of the generator’s output voltage.
6.
Ammeter Change-Over Switch – This switch allows
the AC ammeter to indicate the current flowing to the
load connected to any phase of the output terminals, or
to be switched off.
7.
Voltmeter Change-Over Switch – This switch allows
the AC voltmeter to indicate phase to phase voltage
between any two phases of the output terminals or to
be switched off.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 29
DCA-40SSI — ENGINE OPERATING PANEL
Figure 9. Engine Operating Panel
PAGE 30 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — ENGINE OPERATING PANEL
The definitions below describe the controls and functions of
the DCA-40SSI " Engine Operating Panel " (Figure 9).
1.
Fuel Gauge - Indicates amount of diesel fuel available.
2.
Tachometer – Indicates engine speed in RPM’s for 60
Hz operation. This meter should indicate 1800 RPM’s
when the rated load is applied. In addition a built in hour
meter will record the number of operational hours that
the generator has been in use.
3.
Charging Ammeter Gauge – Indicates the current
being supplied by the engine’s alternator which provides
current for generator’s control circuits and battery
charging system.
4.
Water Temperature Gauge – During normal operation
this gauge be should read between 165o to 215o.
5.
Oil Pressure Gauge – Normal operation should be about
25 psi. When starting the generator the oil pressure
may read a bit higher, but after the engine
warms up the oil pressure should return
to normal.
6.
Starter Switch- Use key to preheat,
start and stop engine.
7.
Pre-Heat Button – Press hold this button
until the preheat lamp is lit (ON).
8.
Engine speed Handle- This handle will
change the speed of the engine from high
to low.
9.
Panel light switch- When activated, will turn on control
panel light.
10. Panel light - Normally used in dark
places or at night. When activated, panel
will luminate. When the generator is not
in use, turn the panel light switch to the
‘OFF’ position.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 31
DCA-40SSI — OUTPUT TERMINAL PANEL
Output Terminal Panel
The output control panel is located on the rear (control panel)
end of the generator. The UNV lugs are protected by a face
plate cover that can be secured in the close position by a
pad lock.
120 Volt Receptacle
One GFCI Duplex NEMA 5-20R (120V, 20 Amp) receptacle
is located on the output terminal. This receptacle can be
used anytime the generator is in operation. The receptacle
is controlled by the circuit breaker located on the control
panel.
The reset button will reset the receptacle after being tripped.
Pressing the :Test Button” (Figure 8) in the center of this
receptacle will check the GFCI function. The receptacle
should be tested at least once a month.
Twist Lock Dual Voltage Receptacles - To use these
receptacles, place the voltage selector switch in the single
phase 240/120 voltage position and adjust the output
voltage to 240 volts with the voltage regulator on the
Control Panel (Figure 8, page 28). Place the voltmeter
change-over switch to the U-W position and the ammeter
change-over switch to the U or W to read the output.
Connecting Load
Loads can be connected to the generator by the UVWO lugs or
the duplex receptacles. (See figure 3). Make sure to read the
operation manual before attempting to connect a load to the
generator.
Figure 11. Load Application
Circuit Breakers
Figure 10. GFCI Test Button
Generator Grounding
Make sure the generator is properly grounded before
applying load. Generators are NOT considered grounded
when mounted on a trailer.
To protect the generator from an overload, a 3-pole, 110 amp,
main circuit breaker is provided to protect the UVWO output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload. Three 50 amp load circuit
breakers have also been provided to protect the load side of
the generator from overload. Make sure to switch ALL circuit
breakers to the "OFF" position prior to starting the engine.
Maximum Output
The entire load connected to the UNV Lugs, all four slots in the
duplex receptacles, and the must not exceed 37.4 kW in
standby or 36 kW in prime output.
Generator Grounding
Make sure to ground the generator in EVERY application
prior to connecting a load. Generators are NOT grounded
just because they are mounted on trailers or other vehicles
that are on rubber tires. See page X for further details.
PAGE 32 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — OUTPUT TERMINAL VOLTAGE SELECTION
DCA-40SSI
NOTE
Legs O and Ground are
considered Bonded Grounds.
Figure 12. Output Panel Location
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 33
DCA-40SSI — OUTPUT AMPERAGE SETUP
Output Terminal Panel Available Voltages
A wide range of voltages are available to supply load to
many different applications. Voltages may be selected by
using the voltage selector switch and depending how you
hookup your hard wire connection to the generator. To obtain
some of the voltages listed, fine adjustment with the voltage
regulator on the control panel is necessary. See Table 8 for
available voltages the generator will supply.
Over Current Relay
An over current relay is connected to the circuit breaker.
During an over current situation, both the circuit breaker and
the over current relay will trip. If the circuit breaker can not
be reset, the reset button on the over current relay must be
pressed. The over current relay is located inside the control
box.
Table 8. Voltages Available
Three Phase
(Sw itchable)
208 VOLT
220 VOLT
240 VOLT
416 VOLT
440 VOLT
480 VOLT
Single Phase
(Sw itchable)
120 VOLT
127 VOLT
139 VOLT
240 VOLT
254 VOLT
277 VOLT
CAUTION :
NEVER switch Voltage Selector Switch
position while the engine is engaged.
Voltage Selector Switch Locking Button
The voltage selector switch has a locking button to protect
the generator and generator load from being switched while
the engine is running. To lock the voltage selector switch,
press in the red button located on the voltage selector switch,
and use a pad lock to hold it into this position.
Maximum Amps
Table 9 shows the maximum amps the generator will provide. Do not exceed the maximum amps listed.
Table 9. Maximum Amps
Rated
Voltage
Maximum Amps
Single Phase
120 Volt
100 amps (4 wire)
Single Phase
240 Volt
50 amps (4 wire)
Three Phase
240 Volt
108 amps
Three Phase
480 Volt
54 amps
PAGE 34 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — OUTPUT AMPERAGE SETUP
Receptacle Use
When the UVWO terminals are providing power, the receptacle power availability will decrease. Do not exceed receptacle power as listed on Table 10.
Table 10. Receptacle Use
Pow er in U se
R eceptacle
P o w er
Available
240/480V
3-Phase
240/120V
Single Phase
or Tw ist
L o ck C S 6369
D uplex
N EMA
5-20R 120V
K VA
KW
KW
45
26
0
40.9
24.8
1.2
36.7
23.6
2.4
32.6
22.4
3.6
28.4
21.2
4.8
Figure 13. Voltage Selector Switch 240/120V Single
Phase
Position
Figure 14 and 15. AC Voltmeter Change-over switch
and Voltmeter Gauge
20
40
60
0
How To Read The Output Terminal Gauges.
The gauges (Figure 15 and 17) and change-over switches
on the control panel DO NOT effect the generator output.
They are to help observe how much power is being supplied
at the UVWO legs.
When the voltage selector switch is in the 240/120V position (Figure 13), place the AC voltmeter change-over switch
to the W-U position (Figure 14) and the AC ammeter changeover switch to the U or W position (Figure 16) to read the
output on the selected leg.
75
A
Figure 16 and 17. AC Ammeter Change-over Switch
and Ammeter Gauge
NOTE
When using plural single phase
voltages, make sure to balance
the load on each of the single
phase legs.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 35
DCA-40SSI — OUTPUT VOLTAGE SETUP
240/120V Hard Wire Hookup
480/240V Hard Wire Hookup
With the voltage selector set and locked at ‘single phase
240/120’ and using single phase 120 volts, the generator
will provide three legs available with 100 amps each on three
different circuits (Figure 18).
With the voltage selector set and locked at ‘3 phase 480/
277’ (Figure 19) and using the 3-phase 240 hookup, it will
provide one circuit available at 108 amps with any two wires
plus the ground (Figure 20).
When using the 3-phase 480 volts hookup, it will provide
one circuit available at 50 amps with all three wires plus
ground.
Figure 19. Voltage Selector Switch 480/277V Three Phase
Position
Figure 18. Hard Wire Hookup at 240/120V Position
Figure 20. Hard Wire Hookup at 480/240V Position
PAGE 36 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- 3 Phase 480/277V Position
The following are additional voltages available when the voltage selector switch is in the ‘3 phase 480/277V’ position.
Single Phase: 480V, 440V, or 416 Volt
This setting can provide single phase power at 480, 440, or
416 volts. After hooking up the hard wires to the lugs as
shown in Figure 23, 480 volts can be obtained with the voltage regulator knob turned toward maximum; 440 volts can
be obtained with the voltage regulator knob is turned down;
and 416 volts can be obtained with the voltage regulator
knob is at the lowest setting.
Figure 21. Voltage Regulator Knob
3 Phase, 480V, 440V, or 416 Volt
This setting can provide 3-phase power at 480, 440, or 416
volts. After hooking up the hard wires to the lugs as shown
in Figure 22, 480 volts can be obtained with the voltage
regulator knob turned toward maximum; 440 volts can be
obtained with the voltage regulator knob is turned down; and
416 volts can be obtained with the voltage regulator knob is
at the lowest setting.
Figure 23. Hard Wire Hookup for Single Phase 480V, 440V,
or 416V
Single Phase: 277V, 254V, or 240V
This setting can provide single phase power at 277, 254, or
240 volts. After hooking up the hard wires to the lugs as
shown in Figure 24, 277 volts can be obtained with the voltage regulator knob turned toward maximum; 254 volts can
be obtained with the voltage regulator knob is turned down;
and 240 volts can be obtained with the voltage regulator
knob is at the lowest setting.
Figure 22. Hard Wire Hookup for Three Phase 480V, 440V, or
416V
Figure 24. Hard Wire Hookup for Single Phase 277V, 254V,
or 240V
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 37
DCA-40SSI — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- 3 Phase 240/139V Position
The following are additional voltages available when the voltage selector switch is in the ‘3 phase 240/139V’ position.
Figure 25. Voltage Selector Switch 240/139V Three Phase
Position
3 Phase, 240V, 220V, or 208 Volt
This setting can provide 3-phase power at 240, 220, or 208
volts. After hooking up the hard wires to the lugs as shown
in Figure 26, 240 volts can be obtained with the voltage
regulator knob turned toward maximum; 220 volts can be
obtained with the voltage regulator knob is turned down; and
208 volts can be obtained with the voltage regulator knob is
at the lowest setting.
Figure 26. Hard Wire Hookup for Three Phase 240V, 220V, or
208V
Single Phase: 240V, 220V, or 208 Volt
This setting can provide single phase power at 240, 220, or
208 volts. After hooking up the hard wires to the lugs as
shown in Figure 27, 240 volts can be obtained with the voltage regulator knob turned toward maximum; 220 volts can
be obtained with the voltage regulator knob is turned down;
and 208 volts can be obtained with the voltage regulator
knob is at the lowest setting.
Figure 27. Hard Wire Hookup for Single Phase 240V, 220V,
or 208V
Single Phase: 139V, 127V, or 120V
This setting can provide single phase power at 139, 127, or
120 volts. After hooking up the hard wires to the lugs as
shown in Figure 28, 139 volts can be obtained with the voltage regulator knob turned toward maximum; 127 volts can
be obtained with the voltage regulator knob is turned down;
and 120 volts can be obtained with the voltage regulator
knob is at the lowest setting.
Figure 28. Hard Wire Hookup for Single Phase 139V, 127V,
or 120V
PAGE 38 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- Single Phase 240/120V
Position
The following are additional voltages available when the voltage selector switch is in the ‘single phase 240/120V’ position.
Single Phase: 120 Volt
This setting can provide single phase power at 120 volts.
After hooking up the hard wires to the lugs as shown in
Figure 31, 120 volts can be obtained with the voltage regulator knob turned to fine tune.
Figure 31. Hard Wire Hookup for Single Phase, 120 volt
Figure 29. Voltage Selector Switch 240/120V Single Phase
Position
Single Phase, 240 Volt
This setting can provide single phase power at 240 volts.
After hooking up the hard wires to the lugs as shown in
Figure 30, 240 volts can be obtained with the voltage regulator knob turned to fine tune.
Figure 30. Hard Wire Hookup for Single Phase 240 volt
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 39
DCA-40SSI — INSTALLATION
Outdoor Installation
Install the generator in a location where it will not be exposed
to rain or sunshine. Make sure the generator is on secure
level ground so it cannot slide or shift around. Also install
the generator so the exhaust will not be discharged in the
direction of nearby homes.
CAUTION :
An electric shock may happen when
vibrators are used. Pay close attention to
handling when operating vibrators and
always use rubber boots and gloves to
insulate the body from electrical shock.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and grounding.
Generator Grounding
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear to the
engine and alternator parts.
Article 250 (Grounding) of the National Electrical Code (NEC)
provides guide lines for proper grounding and specifies that
the cable ground shall be connected to the grounding system
of the building as close to the point of cable entry as
practical.
CAUTION :
Pay close attention to ventilation when
operating the generator inside tunnels and
caves. The engine exhaust contains
noxious elements. Engine exhaust must
be routed to a ventilated area.
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground.
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
1. Use one of the following wire types to connect the
generator to earth ground.
Indoor Installation
a. Copper - 10 AWG (5.3 mm2) or larger.
Exhaust gases from diesel engines are extremely poisonous.
Whenever an engine is installed indoors the exhaust fumes
must be vented to the outside. The engine should be installed
at least two feet from any outside wall. Using an exhaust
pipe which is too long or too small can cause excessive
back pressure which will cause the engine to heat
excessively and possibly burn the valves.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
2. When grounding the generator (Figure 31) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully. Connect the other
end of the ground cable to earth ground.
3. NEC article 250-52(c) specifies that the earth ground
rod should be buried a minimum of 8 ft. into the ground.
NOTE
When connecting the generator to any buildings
electrical system ALWAYS consult with a licensed
electrician.
PAGE 40 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — INSTALLATION
Figure 31.
Typical Generator Grounding Application
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 41
DCA-40SSI — PRE-SETUP
General Inspection Prior to Operation
Circuit Breakers
The DCA-40SSI generator has been thoroughly inspected
and accepted prior to shipment from the factory. However,
be sure to check for damaged parts or components, or loose
nuts and bolts, which could have occurred in transit.
To protect the generator from an overload, a 3-pole, 110 amp,
main circuit breaker is provided to protect the UNV output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload. Three 50 amp load circuit breakers
Extension Cable
have also been provided to protect the load side of the
When electric power is to be provided to various tools or generator from overload. Make sure to switch ALL circuit
loads at some distance from the generator, extension breakers to the "OFF" position prior to starting the engine.
cords are normally used. Cables should be sized to allow
for distance in length and amperage so that the voltage
drop between the generator and point of use (load) is held
to a minimum. Use the Cable Selection Guide (Table 11 )
as a guide for selecting proper cable size.
NOTE
ALWAYS consult with a licensed
electrician for correct extension
cord wire size.
Table 11. Cable Selection (60 Hz, Single Phase Operation)
Load In Watts
Current in
Amperes At 120 At 240
Volts
Volts
Maximum Allowable Cable Length
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
300
600
1000 ft.
600 ft.
375 ft.
250 ft.
5
600
1200
500 ft.
300 ft.
200 ft.
125 ft.
7.5
900
1800
350 ft.
200 ft.
125 ft.
100 ft.
10
1200
2400
250 ft.
150 ft.
100 ft.
15
1800
3600
150 ft.
100 ft.
65 ft.
20
2400
4800
125 ft.
75 ft.
50 ft.
CAUTION: Equipment damage can result from low voltage.
PAGE 42 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — PRE-SETUP
Lubrication Oil
Fuel
Fill the engine crankcase with lubricating oil through the filler
hole, but do not overfill. Make sure the generator is level.
With the dipstick inserted all the way, but without being screw
into the filler hole, verify that the oil level is maintained
between the two notches (Figure 32) on the dipstick. See
Table 12 for proper selection of engine oil.
Fill the fuel tank with clean and fresh diesel fuel. DO NOT
fill the tank beyond capacity.
Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 23
Specification Table 7.
The fuel tank cap must be closed tightly after filling. Handle
fuel in a safety container. If the container does not have a
spout, use a funnel. Wipe up any spilled fuel immediately.
CAUTION :
Figure 32. Engine Oil Dipstick
When checking the engine oil, be sure to check if the oil is
clean and viscous. If the oil is not clean, drain the oil by
removing the oil drain plug, and refill with the specified amount
of oil as outlined in the Isuzu Engine Owner's Manual.
Never fill the fuel tank while the engine is
running or in the dark. Gasoline spillage
on a hot engine can cause a fire or
explosion. If gasoline spillage occurs,
wipe up the spilled gasoline completely
to prevent fire hazards.
Coolant
Use only drinkable tap water. If hard water or water with
many impurities is used, the inside of the engine and radiator
may become coated with deposits and cooling efficiency
will be reduced. See maintenance section on page 52 and
53 on instructions to flush out radiator.
An anticorrosion additive added to the water will help prevent
deposits and corrosion in the cooling system.
Table 12. Recommended Motor Oil
Temperature Range
Type Oil
104° F ~ 23° F
(40° C ~ -5°C)
SAE 30
23° F ~ 5° F
(-5° C ~ -15°C)
SAE 20 or SAE 10W-30
Below 5° C (-15°)
SAE 10W or SAE 10W-30
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 43
DCA-40SSI — PRE-SETUP
CAUTION :
When adding coolant or antifreeze to the
radiator, do not remove the radiator cap
until the unit has completely cooled.
Day-to-day addition of coolant is done from the reserve tank.
When adding coolant to the radiator, DO NOT remove the
radiator cap until the unit has completely cooled. See Table
13. for engine, radiator, and reserve tank coolant capacities.
Make sure the coolant level in the reserve tank is always
between the "H" and the "L" markings.
Table 13. Coolant Capacity
Engine and Radiator
5.3 Gal. (20 L)
Reserve Tank
0.26 Gal. (1L)
Cleaning the Outer Radiator
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the radiator
fins with compressed air. Cleaning inside the radiator is
dangerous, so clean only with the engine turned off and the
battery disconnected.
Air Cleaner
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the Isuzu Engine Owner's Manual.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear and adjust it in accordance with the Isuzu
Engine Owner's Manual.
The fan belt tension is proper if the fan belt bends 10 to 15
mm (Figure 33) when depressed with the thumb as shown
below. Never place hands near the belts or fan while the
generator is running.
Operation in Freezing Weather
When operating in freezing weather, be certain the proper
amount of antifreeze (Table 14) has been added.
Table 14. Anti-Freeze Operating Temperatures
Freezing Point
Boiling Point
Vol %
Anti-Freeze
°C
°F
°C
°F
40
-24
-12
106
222
50
-37
-34
108
226
NOTE
When the antifreeze is mixed with
water, the antifreeze mixing ratio must
be less than 50%.
Figure 33. Fan Belt Tension
CAUTION :
Never place hands near the belts or fan
while the generator set is running.
Adjusting Fan Belt
If the fan belt does not have the 10 to 15 mm defection
follow the procedure below to adjust:
Loosen the alternator adjusting plate and alternator mounding
bolt.
Pivot the alternator at the mounting bolt toward the engine
left or right until the belt reflects the proper tension.
Tighten the mounting bolt and the adjusting bolt.
PAGE 44 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — PRE-SETUP
Battery
This unit is of negative ground. DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary. DO NOT over fill.
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68° F). If the specific gravity
should fall to 1.245 or lower, it indicates that the battery is
dead and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions. Always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help to inhibit corrosion.
Battery Cable Installation
ALWAYS be sure the battery cables (Figure 34) are properly
connected to the battery terminals as shown below. The RED
cable is connected to the positive terminal of the battery,
and the BLACK cable is connected to the negative terminal
of the battery.
CAUTION :
If the battery cable is connected
incorrectly, damage to the generator will
occur. Pay close attention to the polarity
of the battery when connecting the
battery.
When connecting battery do the following:
1. DO NOT connect the battery cables to the battery
terminals when the key is in the ignition and is set in
'START' mode. ALWAYS remove the key from the
ignition and the ignition switch is in the OFF position
when connecting the battery.
2. Place a small amount of grease around both battery
terminals. This will ensure a good connection and will
help prevent corrosion around the battery terminals.
CAUTION :
Inadequate battery connections may
cause poor starting of the generator, and
create other malfunctions.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
Piping and Hose Connection
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness. Tighten all hose clamps and check hoses
for leaks.
Figure 34. Battery Connections
If any hose (fuel or oil) lines are defective replace them
immediately.
Alternator
The polarity of the alternator is negative grounding type.
When an inverted circuit connection takes place, the circuit
will be in short circuit instantaneously resulting the alternator
failure.
Do not put water directly on the alternator. Entry of water
into the alternator leads an electrolyte corrosion causing an
alternator failure.
Before charging the battery with an external electric source,
be sure to disconnect the battery cables.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 45
DCA-40SSI — LOAD APPLICATION
Single Phase Load
CAUTION
CAUTION:
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Motors and motor-driven equipment draw
much greater current for starting than
during operation.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
An inadequate size connecting cable which cannot carry
the required load can cause a voltage drop which can burn
out the appliance or tool and overheat the cable.
NOTE
If wattage is not given on the
equipment's name plate, approximate
wattage may be determined by
multiplying nameplate voltage by the
nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
The power factor of this generator is 1.0. See Table 15.
below when connecting loads.
Table 15. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1.0
Fluorescent lamps, mercury lamps
0.4 - 0.9
Electronic devices, communication
equipment
1.0
Common power tools
0.8
z When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up
to the generating set’s rated output (kW) can be used.
z When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
z When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
If wattage is not available on the equipment, approximate
wattage may be determined by multiplying the nameplate
voltage by the nameplate amperage for three-phase:
WATTS =1.732 x VOLTAGE x AMPERAGE
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
NOTE
If output (kVA) is not given on the
equipment nameplate, approximate
output may be determined by
multiplying voltage by amperage by
Three Phase Load
When calculating the power requirements for 3-phase power
use the following equation:
PAGE 46 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — GENERATOR START-UP PROCEDURE
WARNING:
The engine's exhaust contains harmful
emissions. ALWAYS ventilate the
exhaust when operating inside tunnels,
excavations or buildings. Direct exhaust
away from nearby personnel.
2. Connect the load to the UNV terminals as shown in
Figure 36. These terminals can be found on the output
terminal panel, (see page 33 Figure 12). To gain access
to the output terminals lift the UNV cover. Tighten
terminal nuts securely to prevent load wires from slipping
out.
Before Starting
Engine
1. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
2. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified CC or higher (See Table 12 on page 43).
3. Check the coolant level in the radiator and subtank.
Replenish with antifreeze as necessary. Always maintain
the coolant level between the FULL and LOW markings
on the coolant container. Be sure that the radiator cap is
fastened securely.
4. Check the fuel level on the fuel gauge. If fuel is low, fill
the fuel tank with clean fresh unleaded automotive diesel.
If diesel spillage occurs, completely wipe up the spilled
fuel immediately.
Figure 36. UNV Terminal Lugs (Load)
3. Connect the negative battery cable (BLACK) to the
negative post on the battery (Figure 37).
Before Starting
Generator and Control Panel
CAUTION:
NEVER start the engine with the
main, GFCI or load circuit breakers
in the ON position.
1.
Be sure to disconnect the
electrical load and switch the main, load and G.F.C.I.
circuit breakers (Figure 35) to the “OFF” position prior to
starting the engine.
IVE
ST
PO
E
TIV
GA
NE
RY
E
TT
A
B
Figure 37. Battery Connections
Figure 35. Main, GFCI and
Load Circuit Breakers
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 47
DCA-40SSI — GENERATOR START-UP PROCEDURE
4. Close all engine enclosure doors (Figure 38).
8.
Once the engine is warm and the engine is
running properly, pull and turn the engine throttle
control lever to ‘High’ (Figure 42).
Figure 42. Engine Speed Switch (high)
Figure 38. Engine Enclosure Doors
5.
Check the voltage selection switch (Figure 39) is
at the desired voltage.
Figure 39. Voltage Selection Switch
6.
9. The generator's frequency meter (Figure 43) displays
the 60 cycle output frequency in HERTZ.
Turn and push the engine throttle control lever
(Figure 40) to ‘Low’.
Figure 43. Frequency Meter (Hz)
10. The generator's voltage meter (Figure 44) displays the
120 VAC in VOLTS. If the voltage is not within the
specified frequency tolerance, use the voltage
adjustment control knob (Figure 45) to increase or
decrease the desired voltage.
Figure 40. Engine Throttle Control Lever (low)
7.
Preheat the engine by turning the ignition key to
the left. Once the preheat lamp luminates, turn the
key to the farthest right to start the engine. Once
the engine start to crank, release the key to
‘operation’ (Figure 41).
Figure 41. Starter Switch
Figure 44. Voltage Meter (Volts)
Figure 45. Voltage Adjust Control Knob
PAGE 48 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — GENERATOR START-UP PROCEDURE
11. The ammeter (Figure 46) will indicate zero amps with no 14. The tachometer (Figure 49) will indicate the speed of
load applied. When a load is applied, this meter will
the engine when the generator is operating. Under normal
indicate the amount of current that the load is drawing
operating conditions this speed is approximately 1800
from the generator’s alternator.
RPM’s.
20
40
0
60
75
A
Figure 46. Ammeter (No Load)
12. The engine oil pressure gauge (Figure 47) will indicate
the oil pressure (kg/ cm2) of the engine. Under normal
operating conditions the oil pressure is approximately
25 psi.
Figure 49. Engine Tachometer
15. Turn the MAIN, GFCI and LOAD circuit breakers to
their ON position (Figure 50).
Figure 47. Oil Pressure Gauge
13. The coolant temperature gauge (Figure 48) will indicate
the coolant temperature. Under normal operating
conditions the coolant temperature is between 165 and
215 degrees Fahrenheit.
WATER
Figure 50. Main and GFCI Circuit Breakers
16. Observe the generator's ammeter (Figure 51) and verify
it reads the anticipated amount of current with respect
to the load. The ammeter will only display a current
reading if the load is in use.
TEMP
20
40
0
Figure 48. Coolant Temperature Gauge
60
75
A
Figure 51. Ammeter (Load)
17. The generator will run until manually stopped or an
abnormal condition occurs.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 49
DCA-40SSI — GENERATOR SHUTDOWN PROCEDURE
ENGINE SHUTDOWN
To shutdown the generator, use the following procedure:
1. Switch both the MAIN, GFCI and LOAD circuit breakers
(Figure 52) to the “OFF” position.
EMERGENCY STOP
1. To stop the engine in the event of an emergency, switch
the MAIN, GFCI and LOAD circuit breakers to ‘OFF’
position.
2. Turn the starter switch key to ‘Stop’ position.
Figure 52. Main, GFCI and Load
circuit breakers
2. Turn and push the engine throttle control lever (Figure
53) to the idle (low) position.
Figure 53. Engine Throttle Control Lever
3. Let the engine cool by running it for 3-5 minutes with no
load applied.
4.
Turn the starter switch key to ‘Stop” position (Figure
54).
Figure 54. Off/Manual Auto Switch
5.
Remove the load from the UNV terminal strip.
PAGE 50 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
NOTE PAGE
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 51
DCA-40SSI — MAINTENANCE
General Inspection
Cleaning the Fuel Strainer
Prior to each use, the generator should be cleaned and
inspected for deficiencies. Check for loose, missing or
damaged nuts, bolts or other fasteners. Also check for fuel,
oil, and coolant leaks.
Engine Side (Refer to the Engine Instruction Manual)
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation or
once a month.
Air Cleaner
Check Oil Level
Every 50 hours: Remove air cleaner element and clean heavy
duty paper element with kerosene, or foam element with
liquid detergent and hot water. Wrap foam element in a cloth
and squeeze dry. For heavy duty paper element, wipe
excess kerosene with towel.
Check the crankcase oil level prior to each use, or when the
fuel tank is filled. Insufficient oil may cause severe damage
to the engine. Make sure the generator is level. The oil level
must be between the two notches on the dipstick as shown
in Figure 32, page 43.
The air cleaner is equipped with an indicator. After the dirty
air cleaner has been replaced, press the dust indicator button
to reset the indicator.
Fuel Addition
Add diesel fuel (the grade may vary according to season
and locations). Always pour through the mesh filter.
Removing Water from the Fuel Tank
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally remove the drain
cock and drain the contents. During cold weather, the more
empty volume inside the tank, the easier it is for water to
condense. This can be reduced by keeping the tank full as
much as possible.
Air Removal
If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel, or
after disassembling the fuel system, bleed the system
according to the following procedure.
To restart after running out of fuel, turn the switch to the
“ON” position for 15-30 seconds. Try again, if needed. This
unit is equipped with an automatic air bleeding system.
Replacing Oil Filter
Detach the oil filter cartridge with a filter wrench.
Apply a film of oil to the gasket for the cartridge.
Screw in the cartridge by hand. When the gasket is in
contact with the seal surface, tighten the cartridge one
or two more times by hand.
After the oil cartridge has been replaced, the engine oil
will drop slightly. Run the engine for a while and check
for leaks before adding more oil if needed. Clean
excessive oil from engine.
Replacing Fuel Filter
Replace the fuel filter cartridge with new one every 400
hours or so.
Apply fuel oil thinly over the gasket and hand-tighten
the cartridge into position.
Vent any air.
Fuel Injection Nozzle
z Use an injection nozzle tester to check the static injection
starting pressure and the fuel spray conditions.
z Abnormal fuel consumption will lead to a lowered output
and blackish exhaust smoke. The required injection
starting pressure should be 14.7MPa (150kg/cm2,
2130psi).
Service Daily
If the engine is operating in very dusty or dry grass
conditions, a clogged air cleaner will result. This can lead to
a loss of power, excessive carbon buildup in the combustion
chamber in high fuel consumption.
PAGE 52 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — MAINTENANCE
Feed Pump Strainer Cleaning
The strainer is incorporated in the feed pump inlet side joint
bolt. Clean the strainer with compressed air and rinse it in
the fuel oil.
Flushing Out Radiator and Replacing Coolant
Open both cocks located at the crankcase side and at
the lower part of the radiator and drain coolant. Open
the radiator cap while draining. Remove the overflow
tank and drain.
Check hoses for softening and kinks. Check clamps for
signs of leakage.
Flush the radiator by running clean tap water through
radiator until signs of rust and dirt are removed. DO
NOT clean radiator core with any objects, such as a
screwdriver.
Tighten both cocks and replace the overflow tank.
Replace with coolant (see page 44, Table 14 for mixture).
Close radiator cap tightly.
CAUTION :
Allow engine to cool when flushing out
radiator. Flushing the radiator while hot will
damage radiator.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 53
DCA-40SSI — MAINTENANCE
Valve Clearance Check
3. Remove the timing check hole cover at the front of
injection pump to check the alignment between the
1. In order to bring No. 1 or No. 4 cylinder to top dead center
pointer “a” on the injection pump gear lock plate and the
in the compression stroke, align the notched line on the
projected area mark “b” on the timing gear case.
crank pulley with TDC mark on the timing gear case
cover.
4. If “a” and “b” are in alignment, the timing is set correctly.
If not, follow nos. 1-3 until the “a” and “b” are aligned.
2. Do the adjustment on the circle marked valves in the
below table where No. 1 cylinder is at the center in the 5. Reversely turn the crankshaft pulley counterclockwise
compression stroke.
viewed at the engine front about 30o crank angle.
3. After adjustment started from either piston top center, 6. Remove No. 1 injection pipe from the engine.
turn the crankshaft 360o to align the notched line with 7. Remove the injection pump No. 1 delivery valve holder,
the TDC mark to do the adjustment again on the
delivery valve and spring and reinstall the delivery valve
remaining valve. See Table 16 and Figure 55 for valve
holder on the original place.
arrangement.
8. Delivery valve holder tightening torque:
39~44Nm(29~33lbft.)
Injection Timing Check and Adjustment
9. Slowly turn the crankshaft pulley clockwise and at the
1. Bring No. cylinder to the top dead center on the
compression stroke.
same time continue to feed the fuel with pumping the
Feed pump. When the fuel stop to flow out from No. 1
delivery valve holder, stop pumping.
2. Turn the crankshaft pulley clockwise (viewed at engine
front) and align the notched line on the crank pulley with 10. Observe and make sure which mark (injection starting
the TDC mark on the timing gear case cover.
angle line) on the timing gear case cover is aligning with
the notched line on the crank pulley.
11. The timing line shows the injection starting crank angle
of the engine.
12. The injection starting crank angle should be at the 14o
timing mark.
Table 16. Valve Adustment
(I=Inlet; E=Exhaust)
Cylinder No.
Figure 55. Valve Adjustment
1
2
Valve Arrangement
I
E
I
NOTE:
When No. 1 is at top
dead center in the
compression stoke
X
X
X
Take necessary precautions to prevent dust and
foreign particles in the pump interior when timing
adjustments are made.
When No. 4 is at top
dead center in the
compression stroke
3
E
I
4
E
I
E
O
O
X
O
O
PAGE 54 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — MAINTENANCE
10 Hrs
DAILY
INSPECTION / MAINTENANCE
ENGINE
Check Engine Fluid Levels
X
Check Air Cleaner
X
Check Battery Acid Level
X
Check Fan Belt Condition
X
Check for Leaks
X
Check for Loosening of Parts
X
250 Hrs
Replace Engine Oil and Filter *1
X
Clean Air Filter
X
Drain Bottom of Fuel Tank
X
Clean Unit, Inside and Outside
X
500 Hrs
Change Fuel Filter *2
X
Clean Radiator and Check Coolant Protection
Level
X
Test Fuel Injection Nozzle
X
Replace Air Filter Element
X
Check all Hoses and Clamps
X
Check Valve Clearance
X
Check Injection Nozzle
X
Clean Inside of Fuel Tank
GENERATOR
1000 Hrs
X
X
Measure Insulation Resistance Over 3M ohms
X
*1 Replace engine oil anf filter at 100 hours, first time only.
*2 Replace fuel filter at 250 Hours, first time only.
Generator Storage
For storage of the generator for over 30 days, the following
is required:
z Clean all external parts of the generator with a cloth.
z Cover the generating set and store in a clean, dry place.
z Fill the fuel tank completely.
z Completely drain the oil from the crankcase and refill
with fresh oil.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 55
DCA-40SSI — ENGINE WIRING DIAGRAM
PAGE 56 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — ENGINE WIRING DIAGRAM
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 57
DCA-40SSI — GENERATOR WIRING DIAGRAM
PAGE 58 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
NOTE PAGE
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 59
DCA-40SSI — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, use the tables shown for
diagnosis based on the Engine Troubleshooting (Table 1 7).
If the problem cannot be remedied, consult our company's
business office or service plant.
TABLE 17. ENGINE TROUBLESHOOTING
SYMPTOM
Engine does not start.
POSSIBLE PROBLEM
SOLUTION
No fuel?
Replenish fuel.
Air in the fuel system?
Bleed system.
Water in the fuel system?
Remove water from fuel tank.
Fuel pipe clogged?
Clean fuel pipe.
Fuel filter clogged?
Clean or change fuel filter.
Excessively high viscosity of fuel
or engine oil at low temperature?
Use the specified fuel or engine oil.
Fuel with low cetane number?
Use the specified fuel.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Incorrect injection timing?
Adjust.
Fuel cam shaft worn?
Replace.
Injection nozzle clogged?
Clean injection nozzle.
Injection pump malfunctioning?
Repair or replace.
Seizure of crankshaft, camshaft,
piston, cylinder liner or bearing?
Repair or replace.
Compression leak from cylinder?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Improper valve timing?
Correct or replace timing gear.
Piston ring and liner worn?
Replace.
Excessive valve clearance?
Adjust.
Starter malfunctioning?
Repair or replace.
Wiring disconnected?
Connect wiring.
Starter does not run.
PAGE 60 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — TROUBLESHOOTING (ENGINE)
TABLE 17. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
Engine revolution is not smooth.
Either white or blue exhaust gas
is observed.
Either black or dark gray exhaust
gas is observed.
Deficient output.
POSSIBLE PROBLEM
SOLUTION
Fuel filter clogged or dirty?
Clean or change.
Air cleaner clogged?
Clean or change.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Injection pump malfunctioning?
Repair or replace.
Incorrect nozzle opening
pressure?
Adjust.
Injection nozzle stuck or
clogged?
Repair or replace.
Fuel over flow pipe clogged?
Clean.
Governor malfunctioning?
Repair.
Excessive engine oil?
Reduce to the specified level.
Piston ring and liner worn or
stuck?
Repair or replace.
Incorrect injection timing?
Adjust.
Deficient compression?
Adjust top clearance.
Overload?
Lessen the load.
Low grade fuel used?
Use the specified fuel.
Fuel filter clogged?
Clean or change.
Air cleaner clogged?
Clean or change.
Deficient nozzle injection?
Repair or replace the nozzle.
Incorrect injection timing?
Adjust.
Engine's moving parts seem to
be seizing?
Repair or replace.
Uneven fuel injection?
Repair or replace the injection pump.
Deficient nozzle injection?
Repair or replace the nozzle.
Compression leak?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 61
DCA-40SSI — TROUBLESHOOTING (GENERATOR)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, use the tables shown for diagnosis based on the Engine and Radiator Troubleshooting (Table18) . If the
problem cannot be remedied, consult our company's business office or service plant.
TABLE 18. GENERATOR TROUBLESHOOTING
SYMPTOM
No Voltage Output
Low Voltage Output
High Voltage Output
Circuit Breaker Tripped
POSSIBLE PROBLEM
SOLUTION
AC Voltmeter defective?
Check output voltage using a voltmeter.
Is wiring connection loose?
Check wiring and repair.
Is AVR defective?
Replace if necessary.
Defective Rotating Rectifier?
Check and replace.
Is engine speed correct?
Turn engine throttle lever to "High".
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Short Circuit in load?
Check load and repair.
Over current?
Confirm load requirements and reduce.
Defective circuit breaker?
Check and replace.
Over current Relay actuated?
Confirm load requirement and replace.
PAGE 62 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
NOTE PAGE
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 63
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
*
+, or %, belong to the same assembly or kit.
Note: If more than one of the same reference number is
listed, the last one listed indicates newest (or latest)
part available.
PAGE 64 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI — SUGGESTED SPARE PARTS
DCA-40SSI W/ISUZU 4BG1 DIESEL ENGINE
1 TO 3 UNITS
Qty. P/N
Description
1 ......... 0601808811 .............. CIRCUIT BREAKER
1 ......... 0601820671 .............. AUTOMATIC VOLTAGE REGULATOR
1 ......... 0601840073 .............. RHEOSTAT VOLTAGE REGULATOR
1 ......... 0601840121 .............. KNOB RHEOSTAT
1 ......... M1310500403 ........... RADIATOR HOSE
1 ......... M1310500303 ........... RADIATOR HOSE
1 ......... 8941324900 .............. RADIATOR HOSE
5 ......... 8943212191 .............. OIL FILTER
5 ......... X132400240 ............. FUEL FILTER
5 ......... 0602046368 .............. AIR ELEMENT
1 ......... 0602122272 .............. UNIT OIL PRESSURE
1 ......... 0602123260 .............. UNIT WATER TEMPERATURE
1 ......... 0601810245 .............. BULB, ALARM LAMP
1 ......... 8970208220 .............. FAN BELT
1 ......... 1823100080 .............. STARTER SWITCH
3 ......... KEYISUZUF ............. KEY, STARTER SWITCH
NOTE
Part number on this Suggested Spare
Parts list may supercede/replace the
P/N shown in the text pages of this
book.
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 65
DCA-40SSI --- GENERATOR ASSY.
GENERATOR ASSY.
PAGE 66 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- GENERATOR ASSY.
GENERATOR ASSY.
NO.
PART NO.
1
8051000032
1-1
1-2
8051070003
1-3
0105091025
1-4
030210250
1-5
8041611004
1-6
8041015003
1-7
0105091025
1-8
0042610000
1-9
8001026013
1-10 0601821349
1-11 0601822601
1-12 8001020004
1-13 8001020504
1-14 011008020
1-15 0040080000
1-16 0601000209
1-17 0070806309
2
8051614003
3
8051653004
4
012010030
5
030210250
6
8051340503
7
0845041904
8
8041315102
9
8041350013
10
0010308065
11
0042608000
12
031108160
13
0010108025
14
0040008000
15
031108160
16
060100003
17
8041310014
18
8041312004
19
8041331014
20
0105050616
21
8001333003
22
0010106030
23
0040006000
24
952404470
25
0105091025
26
030210250
27
8051332003
28
0605000010
29
0030012000
0040012000
ITEM
QTY.
REMARKS
ROTOR ASSY.
1
FIELD ASSY.
1
FAN
1
HEX. HEAD BOLT ............................8 .......... REPLACES 0010310025
LOCK WASHER ...............................8 .......... REPLACES 0042510000
COUPLING DISK
4
BALANCING PLATE
1
HEX. HEAD BOLT ............................6 .......... REPLACES 0010310025
LOCK WASHER
6
SET PLATE, RECTIFIER
1
RECTIFIER ......................................2 .......... PT 3610
SURGE ABSORBER .......................1 .......... ERZ-M14JK621A
INSULATOR WASHER
1
INSULATOR WASHER
1
HEX. HEAD BOLT ............................4 .......... REPLACES 0010108020
LOCK WASHER
4
BALANCING WEIGHT KIT
1
BEARING .........................................1 .......... 6309DU
COUPLING RING .............................1 .......... REPLACES M1163400203
REAMER BOLT
1
HEX. HEAD BOLT ............................7 .......... REPLACES 0012110030
LOCK WASHER ...............................9 .......... REPLACES 0042510000
STRATOR ASSY.
1
GROMMET
2
END BRACKET
1
FIELD ASSY. EXCITER
1
HEX. HEAD BOLT
4
LOCK WASHER
4
PLAIN WASHER ..............................4 .......... REPLACES 0041208000
HEX. HEAD BOLT
6
LOCK WASHER
6
PLAIN WASHER ..............................6 .......... REPLACES 0041208000
WAVE WASHER ...............................1 .......... BWW6309
COVER, BEARING
1
GASKET, BEARING
1
COVER, END BRACKET
1
HEX. HEAD BOLT ............................8 .......... REPLACES 0017106012
COVER, END BRACKET
1
HEX. HEAD BOLT
2
LOCK WASHER
2
PLAIN WASHER ..............................2 .......... REPLACES 0041206000
HEX. HEAD BOLT ............................6 .......... REPLACES 0010310025
LOCK WASHER ...............................6 .......... REPLACES 0042510000
COVER, FAN
1
RUBBER SUSPENSION
2
HEX. NUT
4
LOCK WASHER
4
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 67
DCA-40SSI --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 68 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
PART NO.
1
8081812502
2
0601801145
3
0027104010
4
0601823860
5
0027104016
6
0601820671
7
0027105012
8
0601820892
9
0027104016
10
1825500732
11
12
13
14
15
16
17
18
19
20
21
22
23
24
27
28
29
30
31
32
33
34
35
36
37
38
39
40
0027106016
0601823706
0027104016
0601806522
0021004060
0040004000
031104080
M1923100004
0020004010
8051839504
0021003010
0017106016
020106050
3341822503
0601800460
0601800729
0601801040
0601810072
0601810261
0601840073
0601840121
3331824003
0027105016
0030005000
0805001304
031108160
020108060
0027105010
8051814304
0017106016
8081814604
0017106016
0017100025
ITEM
QTY.
REMARKS
CONTROL BOX
1
CURRENT TRANSFORMER, AMMETER ..... 3 ......... CT3.5MR 150/5A
MACHINE SCREW
6
RELAY UNIT .................................................. 2 ......... MSA9013
MACHINE SCREW
4
AUTOMATIC VOLTAGE REGULATOR ............ 1 ......... NTA5A2D; REPLACES 0601820628
MACHINE SCREW
4
OVER CURRENT RELAY .............................. 1 ......... THK20KP; REPLACES 0601820853
MACHINE SCREW
2
EMERGENCY RELAY ................................... 1 ......... REPLACES 1825500730
& 0602200405
MACHINE SCREW
4
RELAY ........................................................... 1 ......... JH1A DC24V
MACHINE SCREW
2
CURCUIT BREAKER .................................... 1 ......... XE100CS 100AT
MACHINE SCREW
2
LOCK WASHER
2
PLAIN WASHER ............................................ 2 ......... REPLACES 0041204000
SELECTOR SWITCH .................................... 1 ......... REPLACES 8010153104
MACHINE SCREW ........................................ 4 ......... REPLACES 0021104010
BRACKET, SELECTOR SWITCH
1
MACHINE SCREW
4
HEX. HEAD BOLT
2
HEX. NUT ...................................................... 2 ......... REPLACES 0030006000
CONTROL PANEL
1
FREQUENCY METER ................................... 1 ......... PAK60 220V 45~65Hz
AC AMMETER .............................................. 1 ......... PSK60 0~75A 0~150A
CHG. OVER SW., AMMETER ....................... 1 ......... SL2VS
PILOT LAMP ................................................. 1 ......... LP132DC 220V
BULB
1
VOLTAGE REGULATOR ................................ 1 ......... RA20A2SE102BJ 2W 1KOHM
KNOB
1
STOPPER, CONTROL PANEL
1
MACHINE SCREW
2
HEX. NUT
2
SET SCREW
2
PLAIN WASHER ............................................ 2 ......... REPLACES 0041208000
HEX. NUT ...................................................... 2 ......... REPLACES 0030008000
MACHINE SCREW
4
COVER
1
HEX. HEAD BOLT
11
SIDE PANEL
1
HEX. HEAD BOLT
4
HEX. HEAD BOLT
4
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 69
DCA-40SSI ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
PAGE 70 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
1
4BD1PD02
ENGINE .......................................... 1 .......... ISUZU 4BD1; REPLACES 0602000078
2
0602010800
RADIATOR ...................................... 1 .......... B961110002
3
0602011303
RADIATOR NECK ........................... 1 .......... 4079111300
4
0602011102
HOSE .............................................. 1 .......... B9611111910
5
0602014062
HOSE BAND ................................... 2 .......... G000100131
6
0602011000
RADIATOR CAP .............................. 1 .......... 7880K11100
7
0017106016
HEX.HEAD BOLT
4
8
3345123104
BRACKET, RADIATOR
2
9
011008020
HEX. HEAD BOLT ........................... 12 ........ REPLACES 0017108020
10
0602013086
RADIATOR HOSE
1
11
0602013186
RADIATOR HOSE
1
12
0602014000
HOSE BAND
2
13
0602014006
HOSE BAND
1
14
0602014071
HOSE BAND
1
15
0602040094
AIR CLEANER ................................ 1 .......... FWG068002
0602040197
ELEMENT, AIR CLEANER .............. 1 .......... P104873
16
0602040690
DUST INDICATOR ........................... 1 .......... RBX002252; REPLACES 062040690
17
0602040587
BAND, AIR CLEANER .................... 2 .......... AAH008218
18
0017108020
HEX. HEAD BOLT
4
19
3342032103
HOSE, AIR CLEANER
1
20
0605515011
HSOE BAND
1
21
0605515028
HOSE BAND
1
22
0602041107
ELEMENT, OIL FILTER .................. 1 .......... 1878102201
23
0602042108
ELEMENT, FUEL FILTER ............... 1 .......... 5878100500
24
3345112503
ENGINE FOOT
1
25
3345112403
ENGINE FOOT
1
26
0041210000
PLAIN WSAHER
8
27
0040010000
LOCK WASHER
8
28
0105091025
HEX. HEAD BOLT ........................... 8 .......... REPLACES 0010710025
29
0605000009
RUBBER SUSPENSION
2
30
0040012000
LOCK WASHER
4
31
0039312000
HEX. NUT ....................................... 4 .......... REPLACES 0030112000
32
1819001931
ENGINE STOPPER ........................ 1 .......... REPLACES 0602210803
33
0027106016
MACHINE SCREW
3
34
3342054104
DRAIN JOINT
1
35
0805013704
PACKING, OIL PAN SIDE
1
36
0805014204
PACKING
1
37
3362054104
JOINT BOLT
1
38
3342051104
DRAIN JOINT
1
39
0802024004
PACKING
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 71
DCA-40SSI ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
PAGE 72 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
40
0802010204
PLUG
1
41
3342022104
DRAIN HOSE
1
42
0605515003
HOSE BAND
2
43
011008020
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0017108020
44
020108060
HEX. NUT ....................................... 2 .......... REPLACES 0030008000
45
0845031303
RESERVE TANK
1
46
0802081104
CAP, RESERVE TANK
1
47
3342082304
BRACKET, RESERVE TANK
1
48
011008020
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0017108020
49
011606025
HEX. HEAD BOLT ........................... 1 .......... REPLACES 0017106025
50
0199500950
HOSE
1
51
0199500175
HOSE
1
52
0193601000
HOSE
1
53
06055150013 HOSE BAND
4
54
0193900750
BREATHER HOSE
1
55
0605515030
HOSE BAND
2
56
0193100700
HOSE
1
57
0605515007
HOSE BAND
1
58
0193800750
HOSE
1
59
0605515019
HOSE BAND
1
60
3342220604
EARTH CABLE
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 73
DCA-40SSI --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
PAGE 74 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
1
3342101003
OPERATING PANEL
1
2
7452142014
SLIDE BAR
1
3
0601840190
KNOB .............................................. 1 .......... REPLACES 0805012904
4
020108060
HEX. NUT ....................................... 1 .......... REPLACES 0036003000
5
7452140504
BRACKET, GOVERNOR ROD
1
6
020108060
HEX. NUT ....................................... 2 .......... REPLACES 0030008000
7
0605010503
SNAP PIN
1
8
0602100004
STARTER SWITCH ......................... 1 .......... 18231000080
9
9825300460
PREHEAT LAMP ............................. 1 .......... REPLACES 0602102006
10
0602120054
TACHOMETER ................................ 1 .......... 25000KX4110
11
0602120154
CABLE, TACHOMETER .................. 1 .......... 6211000KA6710 L=1150
12
0602122060
OIL PRESSURE GAUGE ................ 1 .......... 42000KX1410
13
0602122200
UNIT, OIL PRESSURE .................... 1 .......... 53000AC0101
14
0131300000
STREET SOCKET
1
15
0602123061
WATER TEMPERATURE GAUGE ... 1 .......... 40000KX0910
16
0602123201
UNIT, WATER TEMPERATURE ....... 1 .......... 54100KV0200
17
0602121052
CHARGINE AMMETER .................. 1 .......... 43000KV0300
18
0602103091
ALARM LAMP ................................. 2 .......... REPLACES 0602103090
0601810214
BULB ............................................... 2 .......... REPLACES 0601810244
19
0601830420
SWITCH, LAMP CHECK
1
20
0601810120
PANEL LIGHT ................................. 1 .......... DL31000
0601810201
BULB
1
21
0040520000
TOOTHED LOCK WASHER
1
22
0601830710
SWITCH, PANEL LIGHT
1
23
011008040
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0010008040
0040008000
LOCK WASHER
2
031108160
PLAIN WASHER ............................. 2 .......... REPLACES 0041208000
24
0017108020
HEX. HEAD BOLT
2
25
8055312103
SUPPORT LEG
1
26
0017110025
HEX. HEAD BOLT
2
27
011208025
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0017108025
020108060
HEX. NUT ....................................... 2 .......... REPLACES 0030008000
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 75
DCA-40SSI --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
PAGE 76 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
28
3342183004
LINK, GOVERNOR ROD
1
29
0105091025
HEX. HEAD BOLT ........................... 1 .......... REPLACES 0010010025
30
031110160
PLAIN WASHER ............................. 2 .......... REPLACES 0041210000
31
020310080
HEX. NUT ....................................... 1 .......... REPLACES 0030010000
32
3342182014
GOVERNOR ROD
1
33
3342152114
GOVERNOR ROD
1
34
0602180106
BALL JOINT
2
35
020108060
HEX. NUT ....................................... 2 .......... REPLACES 0030008000
36
0602180108
BALL JOINT
1
37
020106050
HEX. NUT ....................................... 3 .......... REPLACES 0030006000
38
952404470
PLAIN WASHER ............................. 1 .......... REPLACES 0041606000
39
8111860303
SET BOARD, OUTPUT TERMINAL 1
40
0801831704A OUTPUT TERMINAL ....................... 5 .......... REPLACES 0801831704
41
012210020
HEX. HEAD BOLT ........................... 5 .......... REPLACES 0801831804
42
0039310000
HEX. NUT
10
43
0040010000
LOCK WASHER
15
44
0041410000
PLAIN WASHER
20
45
011208030
HEX .HEAD BOLT .......................... 5 .......... REPLACES 0017108030
46
8051865904
COVER, OUTPUT TERMINAL
1
47
0605010051
HINGE
2
48
0027103016
MACHINE SCREW
12
0207003000
HEX. NUT
6
49
0017106016
HEX. HEAD BOLT
2
50
0601811034
RECEPTACLE ................................. 3 .......... CS6369 250V 50A
51
0601811030
RECEPTACLE ................................. 2 .......... 5-20R 125V 20A x 2
52
0027103010
MACHINE SCREW
10
0207003000
HEX. NUT ....................................... 10 ........ REPLACES 0030003000
58413
PLAIN WASHER ............................. 10 ........ REPLACES 0041203000
53
0601805306
CURCUIT BREAKER ...................... 2 .......... KM51 265V 40A
54
0601805840
CIRCUIT BREAKER ....................... 2 .......... KM52 265V 50A
55
8081816303
BRACKET, CIRCUIT BREAKER
1
0223300200
RUBBER SHEET
1
56
0017106016
HEX. HEAD BOLT
2
57
8085182004
RUBBER COVER
1
58
8085183004
SET FRAME, RUBBER COVER
1
59
011206020
HEX. HEAD BOLT ........................... 6 .......... REPLACES 0017106020
60
8051865703
COVER, RECEPTACLE
1
61
012212045
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0010012045
62
031112230
PLAIN WASHER ............................. 4 .......... REPLACES 0041212000
63
0805009804
RUBBER WASHER ......................... 2 .......... REPLACES 0805009804
64
0030012000
HEX. NUT
2
65
0601820015
RECTIFIER
4
66
0601802133
FUSE, 5A
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 77
DCA-40SSI --- BATTERY ASSY.
BATTERY ASSY.
PAGE 78 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- BATTERY ASSY.
BATTERY ASSY.
NO.
PART NO.
1
0168409541
2
0805003904
3
0805004004
4
3802252004
5
031108160
6
0040008000
7
0037808000
8
0215260050
9
0211160160
10
0215860045
11
0602220310
0037808000
12
0602220311
0027808000
ITEM
QTY.
REMARKS
BATTERY ........................................ 2 ........... 95E41R
BATTERY SHEET
2
BATTERY BAND
2
BATTERY BOLT
4
PLAIN WASHER ............................. 4 .......... REPLACES 0041208000
LOCK WASHER
4
WING NUT
4
BATTERY CABLE
1
BATTERY CABLE
1
BATTERY CABLE
1
TERMINAL ASSY. (+) ..................... 2 ........... NO.9P
WING NUT ...................................... 2 ........... REPLACES 0208008000
TERMINAL ASSY. (-) ...................... 2 ........... NO. 9N
WING NUT ...................................... 2 ........... REPLACES 0208008000
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 79
DCA-40SSI --- MUFFLER ASSY.
MUFFLER ASSY.
PAGE 80 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- MUFFLER ASSY.
MUFFLER ASSY.
NO.
PART NO.
1
3342350103
2
1141450690
3
0602323002
4
3342311102
5
3342359104
6
011208025
7
012210020
8
3342356104
9
011208035
10
031108160
11
020108060
12
3342354104
13
3342354004
14
3342328104
15
031108160
16
020108060
17
3342359004
18
011208025
ITEM
QTY.
REMARKS
EXHAUST PIPE
1
GASKET ......................................... 1 .......... REPLACES 0602320000
HEX. NUT ....................................... 6 .......... 9091103100
MUFFLER
1
MUFFLER SHEET
1
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0017108025
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0017110020
GASKET
1
HEX. HEAD BOLT ........................... 4 .......... REPLACES 0017108035
PLAIN WASHER ............................. 4 .......... REPLACES 0041208000
LOCK WASHER .............................. 4 .......... REPLACES 0030008000
COVER
1
COVER
1
PIPE CLAMPER
1
PLAIN WASHER ............................. 2 .......... REPLACES 0041208000
HEX. NUT ....................................... 4 .......... REPLACES 0030008000
COVER SHEET
2
HEX. HEAD BOLT ........................... 4 .......... REPLACES 0017108025
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 81
DCA-40SSI --- FUEL TANK ASSY.
FUEL TANK ASSY.
PAGE 82 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
PART NO.
1
3345510703
1-1
0810105004
1-2
0810105400
1-3
0193100255
1-4
0605515079
2
3345523504
3
0805003414
4
011008020
5
020108060
6
020108060
7
3805522004
8
0131906000
9
0191300670
10
0191300630
11
0605515014
12
0845032204
13
0150000018
14
0802011104
ITEM
QTY.
REMARKS
FUEL TANK
1
CAP, FUEL TANK
1
FUEL FILTER
1
FUEL GAUGE HOSE
1
HOSE BAND
2
TANK BAND
2
PAD, TANK BAND
4
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0017108020
HEX .NUT ....................................... 2 .......... REPLACES 0207008000
HEX. NUT ....................................... 2 .......... REPLACES 0030008000
TANK SHEET
4
CAP
1
SUCTION HOSE
1
RETURN HOSE
1
HOSE BAND
4
DRAIN JOINT
1
O RING
1
PLUG
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 83
DCA-40SSI --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
PAGE 84 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
PART NO.
1
8055111102
2
3345116214
3
011008020
4
3345116504
5
011008020
6
3345121302
3345109103
7
011008020
8
3345122604
9
011008020
10
3345125503
3345109204
11
011008020
12
3345125403
13
011008020
14
3385155104
15
011206020
16
3345125204
17
011008020
18
3345132113
19
3345132213
20
012210040
020114110
030214350
031114260
21
012012030
0040012000
031112230
22
3345141222
3345109303
23
011008020
24
3345155113
3345109413
25
0010008050
0040008000
031108160
26
3345143313
27
3805147104
28
0021006020
020106050
0040006000
ITEM
QTY.
REMARKS
BASE
1
FLOOR PANEL
1
HEX. HEAD BOLT ........................... 10 ........ REPLACES 0017108020
COVER
1
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0017108020
FRONT FRAME
1
LINING
1
HEX. HEAD BOLT ........................... 6 .......... REPLACES 0017108020
BRACKET, RADIATOR NECK
1
HEX. HEAD BOLT ........................... 2 .......... REPLACES 0017108020
COVER, FRONT FRAME
1
LINING
1
HEX. HEAD BOLT ........................... 16 ........ REPLACES 0017108020
COVER, FRONT FRAME
1
HEX. HEAD BOLT ........................... 10 ........ REPLACES 0017108020
COVER
2
HEX. HEAD BOLT ........................... 8 .......... REPLACES 0017106020
COVER, FRONT FRAME
1
HEX .HEAD BOLT .......................... 6 .......... REPLACES 0017108020
CENTER FRAME
1
CENTER FRAME
1
HEX. HEAD BOLT ........................... 8 .......... REPLACES 0010014040
HEX. NUT ....................................... 8 .......... REPLACES 0030014000
LOCK WASHER .............................. 8 .......... REPLACES 0040014000
PLAIN WASHER ............................. 8 .......... REPLACES 0041214000
HEX .HEAD BOLT .......................... 10 ........ REPLACES 0010012030
LOCK WASHER
10
PLAIN WASHER ............................. 10 ........ REPLACES 0041212000
REAR FRAME
1
LINING
1
HEX. HEAD BOLT ........................... 4 .......... REPLACES 0017108020
COVER, REAR FRAME
1
LINING
1
HEX. HEAD BOLT
8
LOCK WASHER
8
PLAIN WASHER ............................. 8 .......... REPLACES 0041208000
DOOR, REAR FRAME
1
WINDOW PLATE
1
MACHINE SCREW
6
HEX. NUT ....................................... 6 .......... REPLACES 0030006000
LOCK WASHER
6
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 85
DCA-40SSI --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
PAGE 86 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
PART NO.
952404470
29
0845028303
30
011208025
31
3345161212
3345109503
32
011008020
33
3345165104
3345109604
34
011008020
35
8055181102
3345105314
36
0010008055
0040008000
031108160
37
3345124013
3345109704
38
3345124113
3345109804
39
3345175104
3345105104
40
011008020
41
3345171813
3345109904
42
3345175004
3345105204
43
011008020
44
3345171923
3345105014
45
0845028203
46
0845028303
47
011208025
48
0601850097
49
0845031504
50
0600500090
51
0021106020
52
B3561100003
53
B3561100103
54
3340630503
ITEM
QTY.
REMARKS
PLAIN WASHER ............................. 6 .......... REPLACES 0041206000
HINGE
2
HEX. HEAD BOLT ........................... 4 .......... REPLACES 0017108025
ROOF PANEL
1
LINING
1
HEX .HEAD BOLT .......................... 16 ........ REPLACES 0017108020
GUIDE PANEL, AIR
2
LINING
2
HEX. HEAD BOLT ........................... 8 .......... REPLACES 0017108020
SPLASHER PANEL
1
LINING
1
HEX. HEAD BOLT
6
LOCK WASHER
6
PLAIN WASHER ............................. 6 .......... REPLACES 0041208000
SIDE DOOR
1
LINING
1
SIDE DOOR
1
LINING
1
GUIDE PANEL, AIR
2
LINING
2
HEX. HEAD BOLT ........................... 12 ........ REPLACES 0017108020
SIDE DOOR
1
LINING
1
GUIDE PANEL, AIR
1
LINING
1
HEX. HEAD BOLT ........................... 4 .......... REPLACES 0017108020
SIDE DOOR
1
LINING
1
HINGE
4
HINGE
4
HEX. HEAD BOLT ........................... 16 ........ REPLACES 0017108025
RUBBER CUSHION
8
CAP
10
EMBLEM ......................................... 2 .......... REPLACES 6360510003
MACHINE SCREW
4
STRIPE ........................................... 1 .......... REPLACES 3340630103
STRIPE, LEFT SIDE ...................... 1 .......... REPLACES 3340630303
STRIPE, RIGHT SIDE
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 87
DCA-40SSI --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
PAGE 88 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
PART NO.
55
3340630904
56
B3561100403
57
B3561100403
58
B3561100204
59
3345104104
60
3345104204
61
3345104304
62
3345104404
63
3345104514
64
3345104614
65
3345104714
66
3345104804
67
3345104904
68
0225100395
69
0220100395
70
0220200750
ITEM
QTY.
REMARKS
STRIPE
2
STRIPE ........................................... 1 .......... REPLACES 3340631104
STRIPE ........................................... 1 .......... REPLACES 3340631304
STRIPE ........................................... 2 .......... REPLACES 3340630704
RUBBER SEAL
2
RUBBER SEAL
2
RUBBER SEAL
3
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
2
RUBBER SEAL
2
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
2
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 89
DCA-40SSI --- DECALS
DECAL ASSY.
PAGE 90 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
DCA-40SSI --- DECALS
DECAL ASSY.
NO.
PART NO.
1
M1550000204
2
3340670112
3
3340670002
4
8050670103
5
M1550000804
6
M9500000004
7
M9500100004
8
M9500300004
9
M9500300104
10
M9500500004
11
M9500500104
12
M9503000004
13
M9503000103
14
M9503100004
15
M9503200004
16
M9510100004
17
M9510200002
18
M9520000004
19
M9520000104
20
M9520000204
21
M9520100004
22
M9520100204
23
M9520100304
24
M9520100404
25
M9520100503
26
M9520200003
27
M9520200104
ITEM
QTY. REMARKS
DECAL; NOTE ........................................................ 1 ...... M15000020
DECAL; GENERATOR CONTROL .......................... 1 ...... S2358B
DECAL; ENGINE OPERATING .............................. 1 ...... S2361A
DECAL; AUXILIARY OUTPUT ............................... 1 ...... S3349
DECAL; NOTE ........................................................ 1 ...... M15000080
DECAL; OIL DRAIN PLUG ..................................... 1 ...... M9000000
DECAL; WATER ..................................................... 1 ...... M90010000
DECAL; - ................................................................ 1 ...... M90030000
DECAL; + ............................................................... 1 ...... M90030010
DECAL; DIESEL FUEL .......................................... 1 ...... M90050000
DECAL; FUEL DRAIN PLUG .................................. 1 ...... M90050010
DECAL; WARNING ................................................. 2 ...... M90300000
DECAL; WATER, OIL CHECK ................................ 1 ...... M90310000
DECAL; WARNING ................................................. 1 ...... M90320000
DECAL; WARNING ................................................. 1 ...... M90320000
DECAL; CAUTION .................................................. 1 ...... M91010000
DECAL; MQ ........................................................... 1 ...... M91020000
DECAL; GROUND .................................................. 1 ...... M92000000
DECAL; AMMETER CHANGE-OVER SWITCH ..... 1 ...... M92000010
DECAL; VOLTMETER CHANGE-OVER SWITCH .. 1 ...... M92000020
DECAL; WARNING ................................................. 2 ...... M92010000
DECAL; CAUTION .................................................. 1 ...... M92010020A
DECAL; SAFETY INSTRUCTIONS ........................ 1 ...... M92010030
DECAL; DANGER .................................................. 1 ...... M92010040
DECAL; WARNING ................................................. 1 ...... M92010050
DECAL; CONNECTION OF OUTPUT CABLE ....... 1 ...... M92020000
DECAL; OVER CURRENT RELAY ......................... 1 ...... M92020010
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 91
ISUZU 4BD1 — CYLINDER HEAD COVER ASSY.
CYLINDER HEAD COVER ASSY.
PAGE 92 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — CYLINDER HEAD COVER ASSY.
CYLINDER HEAD COVER ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
5111101680
CYLINDER HEAD ASSY. .................1 .......... INCL. ITEMS W/#
2#
9117156070
VALVE SEAT, INTAKE
4
3#
9117118030
VALVE SEAT, EXHAUST
4
5#
1096000051
SEALING CUP, REAR FACE
1
5-1# 5112190150
SEALING CUP, EXHAUST MAN. 2
5-2# 1096000160
SEALING CUP, INLET SIDE FACE 4
5-3# 9111291280
SEALING CUP, LOWER FACE
2
5-4# 1096000160
SEALING CUP, TOP FAC
3
5-5# 50960000130 SEALING CUP, DRILLED PASS
4
6#
909600340
PLUG
4
7#
5117210010
VALVE GUIDE
8
9
9111296010
SEAL CUP
4
10
5093000650
ROCKER ARM STUD
3
11
1093000180
INJ. NOZZLE STUD
8
12
9092023100
PLUG, TOP FACE
1
13
9095714100
PACKING, COMMET
1
15
1125690150
VALVE GUIDE SEAL
8
16
9041108250
STUD, INL. MANIFOLD
2
17
9098301770
STUD, EXH. MANIFOLD
3
20
8941458390
GASKET, CYL. HEAD
1
22
8943674370
BOLT ................................................18 ........ REPLACES 8943674380
27
5111702672
CYL. HEAD COVER ASSY. .............1 .......... INCL. ITEMS W/&
28&
9117510381
CAP, OIL FILLER
1
33
9111791050
WSAHER
34
9111790300
PACKING, HEAD COVER
3
50
5111730160
PACKING, CYL. HEAD
1
51
9111750120
NUT
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 93
EA1013
ISUZU 4BD1 — CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
PAGE 94 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
NO
PART NO
1
8941303284
2#
1112611180
3#
5112570011
4#
1090004691
5#
9116110480
5-1# 9116130350
6#
1096000520
6-1# 5112190140
6-2# 1096000121
8
9098600190
9
8941480790
10
1096050681
11
9992055170
11-1 5096050180
12
9992023140
13
9095720140
14
1097400780
15-1 9081510180
18
8941075600
19
5112240040
20
5112901450
21
8943673680
22
8941075662
22-1 8944299951
23
9095720080
27
1096253620
30
5111290030
36
8941745290
37
8943210180
38
0500408180
43
1093000530
49
5096800110
53
9099135050
54
5097070041
56
5117401200
57
9091104080
59
9091505080
60
9091645080
61
8944338700
62
8941625680
66
9097130740
69
5097040331
PART NAME
QTY.
REMARKS
CYL. BLOCK ASSY ........................... 1 ........ INCL. ITEMS W/#
LINING
4
DOWEL
1
BOLT
10
CAM., FRONT METAL
1
CAM., REAR AND CENTER
2
CEALING CUP, FRONT AND REAR 2
SEALING CUP, CYL. BLOCK
1
SEALING CUP, TAPPET D=32
2
PLUG, CAMSHAFT PLATE
1
DOWEL
2
PLUG, HEADLESS PT 1/2
2
OIL PLUG, GALLERY
1
PLUG
7
OIL PLUG, GALLERY
1
PACKING
1
STRAIGHT PIN, GEAR CASE
1
STRAIGHT PIN, FLYWHEEL HSG. 2
INJ. PUMP NIPPLE
1
BUSHING, OIL PUMP DRIVE SHAFT1
COVER, TAPPET CHAMBER
1
PACKING, CYL. BLOCK COVER
2
BOLT
2
BOLT
2
PACKING, COMET
4
SEAL, REAR OIL CRANK
1
SEALING CUP, LEVEL GAUGE
1
COVER, OIL DRAIN
1
PACKING, COVER
1
BOLT
2
STUD, ENGINE FOOT
1
WATER DRAIN COCK
1
PIPE
1
DRAIN PIPE CLIP
1
AIR BREATHER ASSY.
1
NUT
2
LOCK WASHER
2
PLAIN WASHER
2
BREATHER HOSE
1
CLIP .................................................. 2 ........ REPLACES 1097071340
OUOE
1
CLIP
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 95
ISUZU 4BD1 — CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
PAGE 96 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
NO
PART NO
70
0500408160
71
9091606080
80
8941405811
81
1117500120
82
9091104080
83
9091505080
85
9099129760
86
9099155531
92
8970233390
93
5096230350
PART NAME
BOLT
PLAIN WASHER
OIL FILLER ASSY.
OIL FILLER CAP
NUT
LOCK WASHER
HOSE
CLIP
VALVE RELIEF ASSY.
PACKING
QTY.
1
1
1
1
1
1
1
2
1
1
REMARKS
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 97
ISUZU 4BD1 — TIMING GEAR ASSY.
TIMING GEAR ASSY.
PAGE 98 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — TIMING GEAR ASSY.
TIMING GEAR ASSY.
NO.
1
2
3
4
6
7
8
9
10
10
12
13
14
PART NO.
5113110113
9081510180
1113120140
0500408450
1113210790
8943632690
1096253190
9113276020
0500408250
5090000841
5113210090
1112820130
0500406140
PART NAME
QTY.
REMARKS
CASE
1
STRAIGHT PIN
1
PACKING
1
BOLT ............................................................... 6 .......... REPLACES 0500408200
COVER
1
PACKING
1
SEAL
1
POINTER
1
BOLT
7
BOLT
5
COVER, GEAR CHECK
2
GASKET
2
BOLT
4
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 99
ISUZU 4BD1 — FLYWHEEL HOUSING ASSY.
FLYWHEEL HOUSING ASSY.
PAGE 100 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — FLYWHEEL HOUSING ASSY.
FLYWHEEL HOUSING ASSY.
NO.
1
3
4
5
9
9-1
11
PART NO.
8943213303
8943218380
9992023160
9095714160
9910664500
0500408250
9096510690
PART NAME
HOUSING
PLUG, PICK UP HOSE
DRAIN PLUG
PACKING
BOLT
BOLT
PLAIN WASHER
QTY.
1
1
1
1
8
7
8
REMARKS
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 101
ISUZU 4BD1 — OIL PAN ASSY.
OIL PAN ASSY.
PAGE 102 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — OIL PAN ASSY.
OIL PAN ASSY.
NO
1
3#
3-1#
3-2#
4#
4-1#
4-2#
7
9
15
PART NO
8941340361
9096620120
9992023160
9992023240
1096231830
9095714160
9095714240
8943708360
8943706660
0500408180
5117601500
PART NAME
QTY.
REMARKS
OIL PAN ...................................... 1 ........ INCL. ITEMS W/#
PLUG
1
PLUG, THERMO SWITCH
2
HEATER PLUG
1
O RING ....................................... 1 ........ REPLACES 1096230570
PACKING
2
PACKING
1
OIL PAN PACKING ..................... 1 ........ UP TO MAR. 94
OIL PAN PACKING ..................... 1 ........ APR. 94~
BOLT
24
GAUGE ASSY.
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 103
ISUZU 4BD1 — OIL PAN ASSY.
OIL PAN ASSY.
PAGE 104 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — OIL PAN ASSY.
OIL PAN ASSY.
NO
1
3#
3-1#
3-2#
4#
4-1#
4-2#
7
9
15
PART NO
8941340361
9096620120
9992023160
9992023240
1096231830
9095714160
9095714240
8943708360
8943706660
0500408180
5117601500
PART NAME
QTY.
REMARKS
OIL PAN ...................................... 1 ........ INCL. ITEMS W/#
PLUG
1
PLUG, THERMO SWITCH
2
HEATER PLUG
1
O RING ....................................... 1 ........ REPLACES 1096230570
PACKING
2
PACKING
1
OIL PAN PACKING ..................... 1 ........ UP TO MAR. 94
OIL PAN PACKING ..................... 1 ........ APR. 94~
BOLT
24
GAUGE ASSY.
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 105
ISUZU 4BD1 — CRANKSHAFT. PISTON, FLYWHEEL ASSY.
CRANKSHAFT, PISTON, FLYWHEEL ASSY
PAGE 106 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — CRANKSHAFT. PISTON, FLYWHEEL ASSY.
CRANKSHAFT, PISTON, FLYWHEEL ASSY.
NO.
1
1-1
1-2
1-3
1-4
2#
3
4
5
6
7
8&
9&
11
11-1
11-2
11-3
11-4
14
15$
17
18
20
23
24
25
30
31%
33
34
PART NO.
8941170322
8941474660
8941474670
8941474680
8941474690
8941145652
5121112111
5121210050
9122116040
8941075750
1122301041
1122510270
1122350271
9122716080
9122736080
9122746080
9122756080
9122766080
5123101631
9081612200
8941075970
9125210430
8944493660
5123780020
5095030240
9000901570
8970461810
9123336070
5123360030
5123340060
PART NAME
QTY.
REMARKS
CRANKSHAFT ASSY. ..................... 1 ......... INCL. ITEMS W/#
METAL KIT, 0.25
1
METAL KIT, 0.50
1
METAL KIT, 0.75
1
METAL KIT, 1.00
1
METAL SET, THRUST
2
PISTON SET
4
RING SET, PISTON
4
PISTON PIN
4
SNAP RING
8
CONNECTION ROD ASSY. ............. 4 ......... INCL. ITEMS W/&
BUSHING, SMALL END
4
BOLT
8
METAL SET, STD
4
METAL SET, 0.25
4
METAL SET, 0.50
4
METAL SET, 0.75
4
METAL SET, 1.00
4
CRANSHAFT ASSY. ........................ 1 ......... INCL. ITEMS W/$
FLYWHEEL PIN
1
FEATHER KEY
2
CRANKSHAFT GEAR
1
PULLEY
1
NUT
1
WASHER
1
BALL BEARING
1
FLYWHEEL ASSY. ........................... 1 ......... INCL. ITEMS W/%
RING GEAR
1
WASHER
1
BOLT
6
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 107
ISUZU 4BD1 — CAMSHAFT, IDLE GEAR, ROCKER ASSY.
CAMSHAFT, IDLE GEAR, ROCKER ASSY.
PAGE 108 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — CAMSHAFT, IDLE GEAR, ROCKER ASSY.
CAMSHAFT, IDLE GEAR, ROCKER ASSY.
NO.
1
2
3
4
5
6
7
10
11
13
14
17
18
19
21
22
23
24
25
30
31
32
33
34
35
36
37
38
39
40
41
42
43
PART NO.
8944094120
9125221471
9080107200
9116810150
0500408250
5090002360
9098518503
9125310300
9125238014
5125350011
5090300381
1125510501
1125520251
5125610090
1125630351
8941145760
5125650060
5125710032
1125750360
5126110310
9126160420
9091115080
8941295510
9126260050
5126280120
9126281050
1095803350
1090005670
9098514300
9091800190
5096230600
1094001160
9098514300
PART NAME
CAMSHAFT
GEAR
FEATHER KEY
THRUST PLATE
BOLT
BOLT
WASHER
IDLE GEAR SHAFT
IDLE GEAR
THRUST COLLAR
BOLT
INLET VALVE
EXHAUST VALVE
VALVE SPRING
SPRING SEAT, LOWER
SPRING SEAT, VALVE
SPLIT COLLAR
TAPPET
PUSH ROD
ROCKER ARM ASSY.
ADJUSTING SCREW
NUT
ROCKER ARM SHAFT
ROCKER ARM PLUG
BRACKET, FRONT
BRACKET, INNER
SPRING
BOLT
WASHER
SNAP RING
O RING PACKING
NUT
PLAIN WASHER
QTY.
1
1
1
1
2
1
1
1
1
1
2
4
4
8
8
8
16
8
8
8
8
8
1
2
1
4
3
6
6
1
1
3
3
REMARKS
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 109
ISUZU 4BD1 — OIL AND FUEL FILTER ASSY.
OIL AND FUEL FILTER ASSY.
PAGE 110 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — OIL AND FUEL FILTER ASSY.
OIL AND FUEL FILTER ASSY.
NO.
1
2#
10
11
13
14
15
50#
52#&
60
PART NO.
5132002262
1878102201
1132191940
8943706700
5132190261
5090000071
9091505100
9091605100
9132004193
5878100500
0501510350
PART NAME
QTY.
REMARKS
OIL FILTER ASSY. ............................. 1 ............. INCL. ITEMS W/#
OIL FILTER ELEMENT KIT
1
PACKING ............................................ 2 ............. UP TO MAR. 94
PACKING ............................................ 2 ............. APR. 94~
SPACER
1
BOLT
4
LOCK WASHER
4
PLAIN WASHER
4
FUEL FILTER ASSY. .......................... 1 ............. INCL. ITEMS W/&
FUEL FILTER ELEMENT KIT
1
BOLT
2
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 111
ISUZU 4BD1 — OIL PIPING ASSY.
OIL PIPING ASSY.
PAGE 112 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — OIL PIPING ASSY.
OIL PIPING ASSY.
NO.
1
2
3
5
6
7
7-1
10
12
13
PART NO.
8941753012
9099211880
0501408450
5133112561
1096234620
0500408350
0500408320
8944284630
9095720100
909840220
PART NAME
OIL PUMP ASSY.
PACKING
BOLT
FILTER PIPE ASSY.
PACKING
BOLT
BOLT
OIL INJECTION PIPE ASSY.
PACKING
NUT
QTY.
1
2
4
1
2
2
2
1
2
1
REMARKS
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 113
ISUZU 4BD1 — COOLING ASSY.
COOLING ASSY.
PAGE 114 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — COOLING ASSY.
COOLING ASSY.
NO.
1
2#
3&
4&
5&
6&
7&
8&
9%&
11%&
13&
14%
15%&
17%&
19&
21&
23%&
27
28%&
29
31
32
35
37
38
40
41
43
48
49
50
52
53
60
62
63
65
80
81
83
PART NO.
5136101582
8943763780
5878101145
5136310100
5098000520
5136320010
9099521030
9091801470
8942366870
5136210110
5136420530
5136120100
5136130070
9030908200
5136390020
5136340030
5096250570
5096050050
9136140440
0500410400
0500410500
5090300101
5093610700
5097040313
1097040940
9136600930
5136630311
5136420581
5136710450
0500405600
9098516490
5137700320
8941760310
5137160451
9096610050
5096050050
9095713160
8943706740
5137130351
0500408250
0501410250
0500410400
0501410350
5112800111
8943210130
0500408200
0500408250
0500408450
8942059861
PART NAME
QTY.
REMARKS
WATER PUMP ASSY. ...................... 1 ......... INCL. ITEMS W/#
WATER PUMP KIT ........................... 1 ......... INCL. ITEMS W/%
WATER PUMP REPAIR KIT ............. 1 ......... INCL. ITEMS W/&
SHAFT
1
BALL BEARING
2
SPACER
1
SNAP RING
1
SNAP RING
1
SEAL UNIT ASSY.
1
IMPELLER
1
FAN
1
WATER PUMP COVER
1
PACKING
1
SCREW
3
DUST COVER
1
SPACER
1
SEAL
1
PLUG
1
PACKING
1
BOLT
1
BOLT
2
BOLT, WATER PUMP
2
HOSE
1
CLIP, D=38
1
CLIP, D=36
1
FAN ASSY.
1
PULLEY
1
SPACKER
1
BELT
1
BOLT
4
PLAIN WASHER
4
THERMOSTAT
1
PACKING
1
THERMOSTAT HOUSING
1
THERMO PLUG
1
PACKING .......................................... 1 ......... UP TO DEC. 93
PACKING .......................................... 1 ......... DEC. 93~
PACKING .......................................... 1 ......... REPLACES 8943210100
WATER PIPE
1
BOLT
3
BOLT
1
BOLT
2
BOLT
4
WATER DUCT COVER ASSY.
1
OIL COOLER PACKING
1
BOLT
2
BOLT
11
BOLT
8
BOLT
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 115
ISUZU 4BD1 — INTAKE AND EXHAUST ASSY.
INTAKE AND EXHAUST ASSY.
PAGE 116 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — INTAKE AND EXHAUST ASSY.
INTAKE AND EXHAUST ASSY.
NO.
1
3
4
5
8
39
50
50
51
51-1
60
61
62
66
67
69
PART NO.
5141112070
8943632700
9091104080
9091505080
0500408250
5096370281
5141111160
5141111970
0501510300
0500510300
5141410360
5093020020
5141450040
9091104080
9091505080
8942059871
0500408600
PART NAME
INTAKE MANIFOLD
GASKET, INTAKE
NUT
LOCK WASHER
BOLT
PACKING
INTAKE PIPE
INTAKE PIPE
BOLT
BOLT
EXHAUST MANIFOLD
STUD, EXHAUST
GASKET, EXHAUST
NUT
LOCK WASHER
BOLT, L=75
BOLT, FIXED
QTY.
1
1
2
2
6
2
1
1
2
2
1
3
2
5
5
2
1
REMARKS
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 117
ISUZU 4BD1 — FUEL INJECTION ASSY.
FUEL INJECTION ASSY.
PAGE 118 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — FUEL INJECTION ASSY.
FUEL INJECTION ASSY.
NO.
1
3
5
8
9
11
12
13
14
15
15-1#
15-2#
15-3#
16
16-1
16-2
18
20
27
29
29-1
30
31
32
33
34
42
49
49-1
49-2
PART NO.
5153001032
5153150030
9153390510
9091104080
9091505080
8944636740
8944636750
8944636760
8944636770
5154190131
9154196130
9154196140
5154190040
5154190051
0501406160
5154112290
5132600101
5154115730
5154118580
5154112231
5154116030
9099063141
9095714080
9095720140
9099063251
9095720140
5097091030
5097091040
0500406250
PART NAME
QTY.
REMARKS
NOZZLE
4
PACKING
4
DUST COVER
4
NUT
8
LOCK WASHER
8
PIPE, NO. 1
1
PIPE, NO. 2
1
PIPE, NO. 3
1
PIPE, NO. 4
1
CLIP ASSY., D6X2 ................. 3 ................... INCL. ITEMS W/#
CLIP, A
3
CLIP, B
3
BOLT ...................................... 3 ................... NOT SOLD SEPARATELY FROM KIT
CLIP, INTAKE MANIFOLD
1
CLIP, INTAKE MANIFOLD
1
BOLT
1
PIPE
1
OVERFLOW VALVE ASSY. 1
PIPE
1
FILTER LEAK PIPE ASSY. 1
EYE JOINT
1
FILTER PIPE ASSY.
1
BOLT
1
PACKING, COMMET
2
PACKING, FUEL PIPE
6
BOLT
2
PACKING
3
CLIP A
2
CLIP B
2
CLIP BOLT
2
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 119
ISUZU 4BD1 — ENGINE FOOT ASSY.
ENGINE FOOT ASSY.
PAGE 120 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — ENGINE FOOT ASSY.
ENGINE FOOT ASSY.
NO.
1
2
3
4
5
17
18
19
20
22
27
27
28
29
30
31
35
39
42
PART NO.
9117712470
9117712480
8943134650
9091105100
9091505100
5117770080
9117778050
0500410200
5197110620
0501408350
0501408400
0500410000
0500410450
5090300101
8943717120
9091105080
9091505080
9091606080
5136740320
0500408400
9091647080
PART NAME
FOOT, FRONT RIGHT
FOOT, FRONT LEFT
BOLT
NUT
LOCK WASHER
HANGER, FRONT
HANGER, R. REAR
BOLT
BRACKET
BOLT
BOLT
BOLT
BOLT
BOLT, L=75
COVER, PULLEY
NUT
LOCK WASHER
PLAIN WASHER
PLATE
BOLT
PLAIN WASHER
QTY.
1
1
7
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
REMARKS
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 121
ISUZU 4BD1 — ENGINE CONTROL ASSY.
ENGINE CONTROL ASSY.
PAGE 122 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — ENGINE CONTROL ASSY.
ENGINE CONTROL ASSY.
NO.
2
PART NO.
5197890040
PART NAME
BRACKET
QTY.
1
REMARKS
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 123
ISUZU 4BD1 — INJECTION PUMP ASSY.
INJECTION PUMP ASSY.
PAGE 124 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — INJECTION PUMP ASSY.
INJECTION PUMP ASSY.
NO.
1
3#
5#
14#
15#
16#
17#
18#
19#
20#
32
33
35
36
38
39
40
PART NO.
8943440260
8943440280
8941327040
5125240650
1156192450
9096620070
5157810030
8944575170
9884105020
5156190480
1113190090
5090000841
5197510150
0500410250
9091105100
9091605100
9091505100
PART NAME
QTY.
REMARKS
INJECTION PUMP ASSY. ......... 1 ................ INCL. ITEMS W/#
GOVERNOR ASSY.
1
FEED PUMP ASSY.
1
GEAR
1
PLATE
1
BOLT
1
COUPLING
1
BOLT
6
NUT
1
LOCK WASHER
1
PACKING
1
BOLT
7
BRACKET
1
BOLT
2
NUT
1
PLAIN WASHER
1
LOCK WASHER
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 125
ISUZU 4BD1 — ELECTRICAL COMPONENTS ASSY.
ELECTRICAL COMPONENTS ASSY.
PAGE 126 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — ELECTRICAL COMPONENTS ASSY.
ELECTRICAL COMPONENTS ASSY.
NO.
1
6
6
7
8
10
16
16-1
19
20
23
35
35-1
78
79%
PART NO.
1811001910
0500512280
0500512350
9091605120
9829315110
5812002121
9827200690
5824100160
9825139288
5197320020
9825300460
5824500141
8970299880
1819000161
1828490430
PART NAME
QTY.
REMARKS
STARTER ASSY
1
BOLT
1
BOLT
2
PLAIN WASHER
1
CABLE ASSY.
1
ALTERNATOR ASSY.
1
OIL PRESS. WARNING SW.
1
OIL PRESS. WARNING SW.
1
GLOW PLUG (24V)
4
CONNECTOR
1
RESISTANCE CONTROLLER
1
OVERHEAT SWITCH, M16
1
OVERHEAT SWITCH, 3/8
1
STOP ASSY. .................................. 1 ................... INCL. ITEM W/%
CABLE ASSY.
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 127
ISUZU 4BD1 — FEED PUMP COMP. ASSY.
FEED PUMP COMP. ASSY.
PAGE 128 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — FEED PUMP COMP. ASSY.
FEED PUMP COMP. ASSY.
NO.
1
5#
9#
10#
11#
12#
15#
16#%
17#%
18#%
20#
26#
27#
31#
32#
33#
35#
37#
40#
42#
44#
PART NO.
8941327040
5157510120
9813512050
9813513020
9813550230
9813550350
5157540010
9813514030
9813514100
1157590020
9813517020
9813516020
1096230160
5157590270
1156190820
1157590010
1157590030
5157590120
1096230160
9813550250
8941311300
PART NAME
QTY.
REMARKS
FEED PUMP ASSY. .................. 1 ........... INCL. ITEMS W/ #
PUMP HOUSING
1
PISTON
1
SPRING
1
PLUG
1
GASKET
1
TAPPET ASSY. ......................... 1 ........... INCL. ITEMS W/%
ROLLER
1
PIN
1
GUIDE
2
SPRING
2
VALVE
2
O RING
1
BOLT
1
BOLT
1
GASKET
1
ADAPTER
1
JOINT
1
O RING
1
SNAP RING
1
PRIMING PUMP ASSY.
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 129
ISUZU 4BD1 — NOZZLE ASSY.
NOZZLE ASSY.
PAGE 130 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — NOZZLE ASSY.
NOZZLE ASSY.
NO.
1
2
4#
6#
8#
10#
11#
12#
20#
21#
22#
30#
31#
32#
PART NO.
5153110190
1153300941
5153410010
9153430130
5153450010
5153320100
9153390560
9153390570
1153320170
5153390030
5153510010
1153390090
1153390100
9153470030
PART NAME
QTY.
REMARKS
INJ. NOZZLE
4
HOLDER ASSY. ........................ 4 ................ INCL. ITEMS W/#
PUSH ROD
4
SPRING
4
ADJ. SCREW
4
NUT
4
GASKET
4
WASHER
4
RETAINING NUT
4
GASKET
4
CONNECTOR
4
BOLT`
8
GASKET
8
PIN
8
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 131
ISUZU 4BD1 — OIL FILTER ASSY.
OIL FILTER ASSY.
PAGE 132 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — OIL FILTER ASSY.
OIL FILTER ASSY.
NO.
1
2#
4#&
5#&
6#&
7#&
8#
9#
10#
11#
12#
15#
16#
17#
18#
20#
21#
22#
PART NO.
5132002262
1878102201
9099209780
5096230670
9099211950
9132490090
5132120681
9132316020
9099410980
9132390310
9098621170
9000975270
9099408600
8941326650
9099205260
9132260110
9099205260
5132110201
PART NAME
QTY.
REMARKS
OIL FILTER ASSY. .................... 1 ................ INCL. ITEMS W/#
OIL FILTER ELEMENT KIT ....... 1 ................ INCL. ITEMS W/&
PACKING
1
PACKING
1
PACKING
1
PACKING, UPPER
1
BODY
1
BOLT
1
SPRING
1
SEAT
1
DRAIN PLUG
1
OVER FLOW VALVE
1
SPRING
1
VALVE PLUG
1
PACKING
1
PLUG
1
PACKING
1
CASE
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 133
ISUZU 4BD1 — FUEL FILTER ASSY.
FUEL FILTER ASSY.
PAGE 134 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — FUEL FILTER ASSY.
FUEL FILTER ASSY.
NO.
1
2#
3#%
4#%
5#
6#%
7#
8#
9#
10#%
11#
12#
13#
14#
15#
PART NO.
9132004193
5878100500
9099203270
9132136010
9099208410
5096230241
9095720140
1132600470
9099203260
9098518100
9099409010
9132310660
9098620680
9132111071
9132128040
PART NAME
QTY.
REMARKS
FUEL FILTER ASSY. ................. 1 ................ INCL. ITEMS W/#
ELEMENT KIT ........................... 1 ................ INCL. ITEMS W/%
O RING ELEMENT, UPPER
1
PACKING
1
O RING
1
O RING
1
PACKING
2
VALVE
1
PACKING
1
SPRING SEAT
1
ELEMENT SPRING
1
BOLT
1
DRAIN PLUG
1
CASE
1
COVER
1
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 135
ISUZU 4BD1 — ENGINE ACCESSORIES
ENGINE ACCESSORIES
PAGE 136 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
ISUZU 4BD1 — ENGINE ACCESSORIES
ENGINE ACCESSORIES
NO.
1
3
4
PART NO.
8944533000
1096234650
0500408200
PART NAME
TACHOMETER DRIVE ASSY.
PACKING
BOLT
QTY.
1
1
2
REMARKS
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 137
TERMS AND CONDITIONS OF SALE — PARTS
Effective: July 1, 2000
4.
PAYMENT TERMS
Terms of payment for parts are net 10 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and the
carrier.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
5.
Parts must be in new and resalable
condition, in the original Multiquip package
(if any), and with Muiltiquip part numbers
clearly marked.
6.
The following items are not returnable:
a.
Obsolete parts. (If an item is listed
in the parts price book as being
replaced by another item, it is
obsolete.)
b.
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c.
Any line item with an extended dealer
net price of less than $5.00.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific
date and all orders received on or after that date
will be billed at the revised price. Rebates for
price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $20.00 to $50.00 surcharge will be added to
the invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
d.
Special order items.
RETURNED GOODS POLICY
e.
Electrical components.
Return shipments will be accepted and credit
will be allowed, subject to the following
provisions:
f.
Paint, chemicals, and lubricants.
LIMITATIONS OF SELLER’S LIABILITY
g.
Decals and paper products.
1.
h.
Items purchased in kits.
Multiquip shall not be liable here under for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
a.
b.
The list must be typed or computer
generated.
c.
The list must state the reason(s) for
the return.
d.
The list must reference the sales
order(s) or invoice(s) under which
the items were originally purchased.
e.
3.
The parts numbers and descriptions
must match the current parts price
list.
The list must include the name and
phone number of the person
requesting the RMA.
A copy of the Return Material
Authorization must accompany the return
shipment.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for 5 working
days from notification, pending
instructions. If a reply is not received
within 5 days, the material will be returned
to the sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
LIMITATION OF WARRANTIES
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connection with the sale of its products. A part
from such written statement of warranty, there
are no warranties, express, implied or statutory,
which extend beyond the description of the
products on the face hereof.
PAGE 138 — DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01)
NOTE PAGE
DCA-40SSI — PARTS AND OPERATION MANUAL— FINAL COPY (07/10/01) — PAGE 139
PARTS AND OPERATION MANUAL
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
© COPYRIGHT 2001, MULTIQUIP INC.
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
MULTIQUIP INC..
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
SERVICE DEPARTMENT:
800-421-1244
800-835-2551
FAX: 310-537-3927
FAX: 310-638-8046
E-mail:mq@multiquip.com • www:multiquip.com