Craftsman 113.170260 Owner`s manual

f-Save
This Manual _
for Future Reference
SEARS
owner's
manual
MODEL NO.
113.170260
Serial
Number
Model and serial
numbers may be found
on the side of the
detachable blower.You
shouldrecordboth
model and serial
numbers ina safe
place for future use.
FOR YOUR
SAFETY
READ ALL
INSTRUCTIONS
CAREFULLY
CRRFTSMRN®
16 GALLON
WET/DRY VAC
WITH DETACHABLE
BLOWER
• assembly
• operating
• repair parts
J
Sears,
Part No. SP6157
Roebuck
and Co., Hoffman
Estates,
IL. 60179 U.S.A.
Printed
In U.SJL
FULL ONE YEAR WARRANTY
ON CRAFTSMAN WETIDRY VACS
Fwithin one year from the date of purchase, this Craftsman
due to a defect in material or workmanship,
Wet/Dry Vac fails
Seam will repair it, free of charge.
If this Craftsman Wet/Dry Vac is used for commercial or rental purposes,
this warranty coverage applies for only 90 days from date of purchase.
Warranty Service Is Available By Simply Contacting The Nearest
vice Center/department
Throughout
The United States.
This warranty
applies
only while this product
is in the United
Seam Ser-
States.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Seam,
Roebuck
and Co., D/817 WA, Hoffman
Estates,
IL 60179
IMPORTANT SAFETY INSTRUCTIONS
Safety is a combination of common
sense, staying alert and knowing how
your vac works. Read this manual to
understand the vac.
• Do not vacuum, or use this Wet/Dry
Vac
near, flammable or combustible liquids,
gases, or explosive dusts like gasoline
or other fuels, lighter fluid, cleaners, oilbased paints, natural gas, hydrogen,
Safety Signal Words
coal dust, magnesium dust, grain dust,
or gun powder.
DANGER: means if the safety information
is not followed someone will be seriously
injured or killed.
• Do not use Wet/Dry Vac as a sprayer.
Do not vacuum anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
WARNING: means if the safety information is not followed someone could be
seriously injured or killed.
Do not vacuum fireplace soot or ash. This
is a very fine dust which will not be captuned by the filter and may cause damage.
CAUTION: means if the safety information is not followed someone may be
injured.
To reduce the risk of health hazards from
When using your Wet/Dry Vac, follow
basic safety precautions including the following.
vapors or dusts, do not vacuum toxic
materials.
Do not use or store near hazardous materials.
reduce the risk of electric shock, do not
WARNING-ToroduceToexpose
to rain. Store indoors.
the risk of fira, electric
injury:
shock, or
Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
Read and understand this owner's manual
and all labels on the Wet/Dry Vac before
operating. Use only as described in this
manual. To reduce the risk of personal
Do not use this Wet/Dry Vac with a torn filter or without the filter installed except for
vacuuming liquids as described in the
operation section of this manual.
injury or damage to Wet/Dry Vac, use only
Sears Craftsman recommended accessories.
Do not leave Wet/Dry Vac when plugged
in. Unplug from outlet when not in use and
before servicing. Turn offWet/Dry Vac
before unplugging.
Sparks inside the motor can ignite flammable vapors or dust. To reduce the risk
of fire or explosion:
2
To reduce the risk of injury from accidental starting, unplug power cord before
changing or cleaning filter.
Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
Do not use with damaged cord, plug or
other pads. If your Wet/Dry Vac is not
working as it should, has missing pads,
has been dropped, damaged, left outdoors, or dropped into water, return it to a
Sears Service Center.
Do not pull or carry by cord, use cord as
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not
run WetJDry Vac over cord. Keep cord
away from heated surfaces.
Do not handle plug or the Wet/Dry Vac
with wet hands.
Vacs before servicing.
Use this WetJdry Detachable
as described in this manual.
When using as detached blower:
• Turn unit off before setting on ground or
releasing grasp from handle.
• Do not use on wet surfaces, electric
shock could occur.
• Direct air discharge only at work area.
• Do not direct air at bystanders.
• Keep children away when blowing.
• Do not use blower for any job except
blowing dirt and debris.
Observe the following warnings that
appear on the motor housing of your Wet/
Dry Vac.
'-_
Do not put any object into ventilation
openings. Do not vacuum with any ventilation openings blocked; keep free of dust,
lint, hair or anything that may reduce air
flow.
OUBLE INSULATED
GROUN_NG NOT REQUIRED
WHEN SERVICING USE ONLY
IDENTICAL REPLACEMENT PARTS
WARNING:
Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving pads.
To reduce the risk of falls, use extra care
To reduce the risk of
electric shock- do not expose to
rain-store
indoors.
WARNING: For your own safety,
read and understand owner's man-
when cleaning on stairs.
This Wet/Dry Vac is double-insulated,
eliminating the need for a separate
grounding system. Use only identical
replacement pads. Read the instructions
for Servicing Double-Insulated
Blower Vac
ual. Do not pick up hot ashes, coals,
toxic, flammable or other hazardous materials.
Do not use around
explosive
Wet/Dry
liquids or vapors.
SAVE THESE INSTRUCTIONS
For dust operations, wear dust mask.
Use only extension cords that are 'rated
for outdoor use. Extension cords in poor
condition or that are too small in wire size
The operation of any utility vac or blower
can result in foreign objects being blown
into the eyes, which can result in severe
eye damage. Always wear safety goggles
complying with ANSI Z87.1 (shown on
package) before commencing
operation.
Safety Goggles are available at Sears
retail stores.
can pose fire and shock hazards. When
using an extension cord, be sure it is in
good condition. Using any extension cord
will cause some loss of power. To keep
the loss to a minimum, use the foUowing
table to choose the minimum wire size
extension cord.
To reduce the risk of hearing damage,
wear ear protectors when using the vac
for extended hours or when, using !tin a
noisy area.
3
Extension
Cord Length
Gauge
(A.W.G.)
0-50 Ft.
50-100 Ft.
14
12
Mtroduc on
Table of Contents
This Wet/Dry Vac is intended for household use only.
Item
Page
Warranty Information .............................
2
IMPORTANT NOTE
Please Read Carefully
Static Shocks Are Common - In dry
areas or when the relative humidity of the
air is low. To reduce the frequency of
static shocks in your home the best remedy is to add moisture to the air with a
console humidifier.
Unpacking
Safety Instructions .................................
Introduction ............................................
2
4
Unpacking and Checking
Carton Contents .............................
4
Assembly ...............................................
OperatiQn ...............................................
Maintenance ........................................
Repair Parts .......................................
and Checking Carton Contents
Remove entire contents of carton. Check
B
each item against the Carton Contents List.
Some units may include accessories not
shown. Notify your Sears Store immediately if any parts are damaged or missing.
C
Carton Contents List
Key
A
B
DescripUon ............................
Qty.
16 Gallon Wet/Dry Vac ............... 1
Hose ..........................................
1
C
D
Blower Adapter ..........................
Diffuser ......................................
1
1
E
Blower Nozzle ............................
1
F
G
H
Utility Nozzle ..............................
Wet Nozzle .................................
Car Nozzle .................................
1
1
1
J
Extension Wands .......................
2
K
L
Accessory Caddy .......................
Float ...........................................
1
1
M
N
P
R
Filter
Filter
Filter
Filter
Cage .................................
(Red Stripe) ......................
Plate ..................................
Nut ....................................
1
1
1
1
S
T
U
Single Wheel Caster ..................
Wheel Assembly ........................
Owners Manual ..........................
2
2
1
L
©
K
S
M
4
5
9
13
.16
Accessory
Caddy Assembly.
1. Unlatch the drum latches on the front
and rear of unit. The drum latches hold
the lid onto the drum. Lift the lid off the
Dove
Tail
drum. Place the lid upside down on a
clean smooth surface.
..__/Drain
2. Flip the drum upside down on the floor.
3. Take the accessory caddy and position
it on the vac drum. The open end of
horseshoe shaped caddy should be
positioned under the drain cap:
4. Slide the caddy down onto the-drum,
the open end of the caddy has two
/_'___.1_l
dovetail slides that will press into the
molded area of the drum. The caddy
will press onto the drum until it rests
against the first step of the drum. The
Dove
Caddy
bottom edge of the caddy will be even
with the bottom edge of the vac drum. If
it is not even with the bottom of the
drum, tap the edge until it is flush with
the drum bottom. The tab lock located
at the rear of the caddy will latch into
the recessed area at the rear of the vac
drum.
_b
Lock
To Install the Wheels/Casters
Wheel
1. Locate the two 5-1/4" wheel assemblies
Support
and the single wheel casters.
_
2. Insert the single wheel casters into the
bottom of the accessory caddy as
shown (2 places).
3. Push on the caster until the end of the
i
caster stem is inserted all the way into
the socket. You will be able to hear the
end of the caster snap into the socket of
the caddy. The caster will rotate easily
when positioning is correct.
4. Position the dovetail section of one of
the wheel assemblies into the accessory caddy as illustrated. Tap the wheel
support of the assembly with a soft mal-
5. Flip the drum/caddy assembly upright
with the wheels of the caddy resting on
the floor.
let if necessary. Repeat for the second
wheel assembly.
NOTE: When emptying debris from the
wet/dry drum, it is not necessary to
remove the vac caddy.
5
Float/Cage
WARNING:
For-your
Assembly
own safety,
Detachable
never connect _plug to power source
outlet until all assembly steps are
complete and you have read and
understood
the safety and operation
instructions.
Do not operate vac with
any parts damaged or missing.
1. Remove the detachable blower from the
power head assembly by pressing
down on the power head latch beneath
the carry handle of the detachable
blower. Set the detachable blower off to
/
the side. Place lid upside down on
drum.
Drum
Latch
2. Locate the float and filter cage. (The
Power Head
Latch
Lid Asm.
float is inside the loose parts bag.)
3. Place the float over the center opening
in the lid with the words "This side
_1
j
towards lid" laying face down over the
hole. (See illustration.)
Cage
4. Line up the filter cage tabs as shown
,,1/Tabs
with the slots in the center ring of the lid
assembly. Push on the filter cage until
the tabs snap into the slots for a secure
fit.
NOTE:
Filter
Solid
End
If filter cage needs to be removed,
because the float is placed in the wrong
way, use a fiat blade screwdriver and
insert the blade near one of the tabs
between the filter cage and the center ring
of the lid. Pry the tab out of the slot. Tilt
the cage and lift away from the lid. To
replace,
follow
float/cage
assembly
instructions.
6
(3)
End
Filter Assembly
1. Carefully slide the filter over the filter
cage, sliding it over the center ring covering the 3 slots until the filter stops
against the lid.
Red
2. Place the hole in the filter plate over
threaded screw of the filter cage.
Stripe
3. Gently push on the filter plate to seat
the rubber ring of the filter inside the circular channel of the filter plate.
4. Place filter nut onto threaded screw and
tighten it down. Finger tighten only.
Lid
Cage
NOTE: Lever of filter nut should be away
from plate as shown.
IMPORTANT:
Do not overtighten as this
may deform or crack the filter plate, filter
cage or the filter.
NOTE: Your filter has a red stripe that
matches an in-store displayer. When you
visit your local Sears store, just remember
the color of your stripe for the correct size
filter.
Vac Assembly
Latch
Latch
1. Locate the lid assembly and the drum/
caddy assemblies (assembled earlier).
2. Position the lid assembly with the inlet
of the unit located in line with the drain
cap and the drum label on the vac.
Allow the assembly to rest on the vac
drum.
3. Rotate both latches down until you hear
the latches snap over the lip of the
drum.
NOTE: For best appearance of the unit,
the inlet of the vac should be located
above the drain.
Inlet
Drum
-Drain
Positioning Detachable Blower
(Power Head Assembly)
1. Locate the detachable blower of your
Craftsman wet/dry vac.
Molded
Plastic Lead
2. On top of the blower (opposite the handle side of the blower); there is molded
plastic lead that is used to assist
assembling the unit. Position the lead
into the indented area above the label.
3. Rotate the detachable
Area
blower down
until the travel of the unit stops.
4. Lightly press down on the carry handle
of the detachable blower until the power
head latch engages the blower. The
detachable blower is now latched to the
Power Head
Latch
lid assembly.
Release
Button
Your new wet/dry vac is ready for use.
With the wet/dry vac completely assembled and ready for use, insert the push button end of the hose assembly into the inlet
of the vac. The hose should snap into
place. To remove the hose from the vac
press the release button in the hose
assembly and pull the hose out of the vac
inlet.
8
I-I
Press and
Pull
Operation
WARNING
To reduce the risk of fire or explosion, do not operate this vac in areas with
flammable gases or flammable vapors such as lighter fluid, cleaners, oil-base
paints, gasoline, alcohol or explosive dust such as coal, magnesium,
grain or
gun powder In the air. Do not vacuum explosive dust, flammable or combustible liquids or hot ashes. Do not use this vac as a sprayer. To reduce the risk of
health hazards from vapors or duste, do not vacuum toxic materials.
To reduce
the risk of electrical shock do not expose to rain. Store vac indoors. Unplug
power cord before changing or cleaning filter or emptying the dust drum.
CAUTION:
To reduce
the risk of hear-
2. When using your vac to pick up very
fine dust, it will be necessary for you to
empty the drum and clean the filter at
more frequent intervals to maintain
ing damage wear ear protectors
when using the vac or blower for
extended hours or when using it in a
noisy area. The operation of any utility vac or blower can result in foreign
objects being blown into the eyes,
which can result in Severe eye dam-
peak vac performance.
NOTE: A dry filter is necessary to pick up
dry material If you use your vac to pick up
dust when the filter is wet, the filter will
clog quickly and be very difficult to clean.
age. Always wear safety goggles
complying with ANSI Z87.1 (shown
on Package) before commencing
operation. Safety Goggles are available at Sears retail stores.
3. If your filter is wet but you need to use
the vac to pick up dry material, you can
quickly dry the filter by running the vac
without hose attached for about 10 min-
If the noise level of this unit is too loud,
utes. The clean air rushing through the
vac will help dry the filter.
purchase the Craftsman Noise Muffler;
accessory number 9-16991 found in
Sears retail stores or the Sears Power
and Hand Tool Catalog.
To reduce the risk of electric
The optional Craftsman Fine Particle Filter, stock number 9-17916 will do a better job stopping the very fine particles
than the 9-17816 filter. This filter will stop
99.99% of all particles as small as one
micron.
shock, this
appliance has a polarized plug (one blade
is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
Vacuuming Liquids
plug. If it still does not fit, contact a qualified electrician to instaJl the proper outlet.
Do not change the plug in any way.
NOTE: When using the unit in the vacu-
1. When picking up small amounts of liquid the filter may be left in place.
2. When picking up large amounts of liquid we recommend that the filter be
uming mode, always insert the air diffuser
in the exhaust port on the detachable
blower. This breaks up the direct flow of
air and diffuses it.
Vacuuming
removed. If the filter is not removed, it
will become saturated and misting may
appear in the exhaust.
3. After using the vac to pick up liquids,
the filter must be dried to reduce the
Dry Materials
1. The filter must be in correct position at
all times to reduce the risk of leaks and
risk of possible mildew and damage to
the filter.
possible damage to vac,
9
Operation (continued)
4. When the liquid in the drum reaches a
predetermined level, the float mechanism will dse automatically to cut off airflow. When this happens, turn off the
vac, unplug the power cord, and empty
the drum. You will know that the float
has risen because vac airflow ceases
and the motor noise will become higher
in pitch, due to increased motor speed.
IMPORTANT:
To reduce the risk of dam-
age to the vac do not run motor with float
in raised position.
Emptying Dust Drum
WARNING:
To reduce
the risk of
injury from accidental starting,
unplug power cord before emptying
the drum.
I
1. To remove the lid to empty contents of
Latch
the dust drum, simply lift the two drum
latches at the front and rear of the dust
drum and lift the lid assembly up and off
the dust drum and set to the side.
NOTE: Do not pick up the lid assembly
by lifting on the handle to the detachable blower. Lift the lid assembly by the
latches. This will ensure that the
detachable blower and the lid will not
separate during removal of the lid
assembly.
4. If the contents are liquid, you may dispose by using the drain provided in the
drum for easy emptying. Simply
unscrew the drain cap and allow the liq-
2. Lay the lid assembly upside down on a
uid to drain completely
drum.
clean dry area while emptying the drum
or changing the filter.
3. Dump the drum contents into the
proper waste disposal container.
WARNING:
out of the vac
To reduce the risk of
back injury or falls, do not
i heavy with liquid or debris.
i drain enough contents out
the vac light enough to lift
ably.
10
lift a vac
Scoop or
to make
comfort-
To Store Your Accessories
Your Craftsmall wet/dry vac caddy is
designed to provide better stability and
accessorystorage.Thereare five storage
pockets located at the rear of the vac
caddy and two storage areas at the front
of the storage caddy. Conveniently store
accessory nozzles and extension wands
on the rear of the caddy and use the front
storage for hose storage and/or male to
male and air diffuser storage.
Cord Wrap
When vacuuming is complete, unplug the
Cord Wrap
Area
cord and wrap it around the lid assembly
in the area provided between the inlet and
the raised letter area marked =Cord
/
Wrap".
11
Operation (continued)
Moving the Vac
Should it become necessary to pick the
Handle
/
vac up to move it, the handles may be
used on the sides of the dust drum. Do
not use the handle located on the detachable blower to pick up the entire wet/dry
vac or the lid assembly.
Handle
Blowing Feature
Your wet/dry vac features a =detachable
blower'. It has the capability to be used as
WARNING: To reduce the risk of
,njury to bystanders, keep them clear
a dedicated blower for yard work, patio
cleanup and workshop applications to
blow sawdust and other debris.
of blowing debr e.
WARNING: Always wear safety goggles complying with ANSI Z87.1
when using as a blower.
WARNING:
Wear a dust mask if blow-
ing creates
inhaled.
dust which
CAUTION:
might be
1. Familiarize yourself with the detachable
blower portion of your wet/dry vac.
2. Remove the detachable blower of your
vac by pressing down on the latch
under the handle of the detachable
blower. This latch holds the detachable
blower to the lid assembly.
3. Lift the detachable blower up by raising
the handle upward and pulling the unit
away from the nested position of the
To reduce the risk of hear-
ing damage wear ear protectors
when using the vac/blower for
extended hours or when using it in a
hinges.
noisy area.
Assemble
the Detachable
Blower for "Blowing"
This may be assembled two ways.
1. Insert the small end of one of the exten-
Blowing
sion wands into the blowing port of the
detachable blower. Insert the blowing
Port
Extension
Wand
adapter into the extension wand and
install the blower nozzle onto the blowing adapter.
-OR2. Insert the blowing adapter into the
blowing port of the detachable blower.
Connect the large end of the extension
wand to the blowing adapter. Connect
the blower nozzle to the extension
wand.
Blowi_
Adapter
Blower
Nozzle
3. Turn the blower =ON" by toggling the
switch in the handle of the blower to the
"ON" position.
12
. _
I
I
The wet/dry vac may also be used for
blowing using the seven foot hose suppliedwith the wet/dryvac.
Install the blower adapter in the blowing
port of the wet/dry vac.
The blower adapter will insert
inside of the push button end of the vac
hose. Assemble the hose to the blowel
adapter and connect the blower nozzle tc
the opposite end of the hose.
The unit is ready for blowing applications.
into the
Blower Nozzle
Blowing
Port
Blower
Adapter
Blower Nozzle
Maintenance
Blower Intake
injury from accidental starting,
unplug power cord before changing
I WARNING: To reduce the risk of
or cleaning filter,
After using the detachable blower of your
wet/dry vac, examine the bottom of the
blower for dust and debris. Check to see if
the intake to the blower has debris stuck
Pad Holder
to the plastic vents and foam pad.
To clean the foam pad under the intake
shield of the detachable blower:
1. Remove the three screws holding the
intake shield.
2. Lift the intake shield off and set aside.
) Shield
3. Lift the foam pad away from the
detached blower, the foam pad holder
will also lift away from the blower.
4. Remove the foam pad from the foam
pad holder and set the foam pad holder
to the side. Clean the foam pad in warm
soapy water or brush debris away.
Allow foam pad to dry.
5. Examine foampad
for reuse. If you
need to replace it, check the service
part section of this manual.
: -
Screws
(3)
6. Replace foam pad holder on blower
with the tabs away from the blower.
Reinstall foam pad under the tabs of the
holder.
7. Reinstall intake shield and 3 screws.
The unit is ready for use.
13
Maintenance (continued)
Cleaning
Vac Filter
II
I
Dry Filter
Your filter should be cleaned often to
maintain peak vac performance.
Be sure to dry the filter before storing or
1. Some removal of dry debris can be
accomplished without removing the filter
from the vac by slapping your hand on
top of the lid while the vac is turned off.
picking up dry debris.
IMPORTANT: After cleaning, check the
filter for tears or small holes. Do not use a
filter with holes or tears in it. Even a small
2. For best results of cleaning due to
accumulated dust, clean the filter in an
open area. Cleaning SHOULD be done
outdoors and not in the living quarters.
hole can cause a lot of dust to come out of
your vac. Replace it immediately.
3. After filter removal from vac, remove the
NOTE: This filter is made of high quality
paper designed to stop very small particles of dust. The filter can be used for wet
dry debris by gently tapping the filter
against the inside wall of your dust drum
and the debris will loosen and fall.
or dry pick up. Handle the filter carefully
when removing to clean or installing it.
Creases in the filter pleats may occur from
installation but creases will not affect the
4. For thorough cleaning of dry filter with fine
performance
of the filter.
dust (no debris), you may run water
through it as described under 'Wet Filter'.
Wet Filter
Removal
After filter is removed, run water through
the filter from a hose or spigot. Take care
To remove the filter for cleaning or
that water pressure from the hose is not
replacement, remove filter nut from the
screw on the filter cage, remove filter plate
and lift off filter.
strong enough to damage filter. Remember: To dry a filter quickly, reinstall the filter on the vac and allow the unit to run for
IMPORTANT:
To reduce the risk of dam-
age to the blower wheel and motor,
always reinstall the filter before using the
vac for dry material pickup.
CAUTION:
Do not remove
the filter
cage or float. It is there to shut off airflow when the drum is full of liquids.
approximately
10 minutes. The clean air
rushing through the filter will dry it.
Installation
Refer to "Filter Assembly".
Allow the filter to dry before reinstalling
and storing the vac.
Wet/Dry Vac
To keep your Wet/Dry Vac looking its best,
clean the outside with a cloth dampened
3. Wipe out with dry cloth.
WARNING: To assure product SAFETY
and RELIABILITY, repairs and adjust-
with warm water and mild soap.
To clean the drum:
ment should be performed by Sears
Service Centere, always using Sears
replacement parts.
1. Dump debris out.
2. Wash drum thoroughly.
14
Wet Nozzle
farthest from you.)
To pick up liquids off a smooth surface,
use the 2-1/2" wet nozzle accessory supplied with your wet/dry vac. To use this
nozzle, simply attach the nozzle to the
end of an extension wand.
Connect a second extension wand to the
2. Using both hands, lower the nozzle
body onto the insert and squeegee with
the round opening of the nozzle closest
to you. With fingers on the far side and
thumbs holding the latches of the
removable insert, flip the nozzle over so
the latches are on the top and the round
inlet opening is facing away from you.
Make sure the squeegee stays on the
first, and connect the 2-1/2" x 7' hose to
the extension wand.
Liquids may be picked up by dragging the
nozzle across the surface. The squeegee
will dry the surface as you vacuum.
Replacement rubber for the SClueegee
nozzle may be obtained through Sears
Parts. If the rubber becomes worn, it may
insert pins.
be flipped over for use on the opposite
side or replaced. (Replacement service
part #822256).
To reverse or replace the
squeegee"
1. Lay the wet nozzle on a fiat surface with
the round inlet opening facing up and
the two latches close to you as shown.
Latches
3. Press down with each thumb below the
latching tabs until you see and hear the
removable insert snap into the nozzle
Nozzle
body. Snap the latches over the locking
tabs into their original position.
{
Removable
Insert
)
2. Using both hands, position each thumb
on the removable insert, (below the
4. Inspect the pins of the insert to make
sure they fit through the holes of the
squeegee and fit into the matching slots
in the nozzle body.
latches) and two fingers of each hand
on each latch, lift and disengage the
two latches from the tabs on the nozzle
NOTE: If the pins are out position, hold
the nozzle assembly with both hands
body.
and gently twist in opposite directions.
The insert pins should snap into
3. Gently pull the latches toward yourself
to remove the insert.
To reinstall the removable
follow these steps:
1. Place the removable
proper position.
Twist
Backward
insert correctly,
Twist
Forward
insert on a flat sur-
face with the pins positioned upward
and the latches dose to you as shown.
Place the rubber squeegee on the
insert, with the pins fitting through the
matching holes in the squeegee. (Make
sure the new working edge is located
The wet nozzle assembly is ready for wet
pickup use.
15
Repair Parts
,,
16 Gallon
Wet/Dry
Vac With Detachable
Blower
Model Number 113.170260
Always order by Part Number - Not by Key Number
WARNING
SERVICING
In a double-insulated
OF DOUBLE-INSULATED
Wet/Dry
Vac, two systems
WETIDRY
of Insulatlon
VAC
are provided
instead of grounding.
No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added. Servicing a double-lnsulated Wet/Dry Vac requires extreme care and knowledge of the system, and
should be done only by qualified service personnel. Replacement
parts for a
double-insulated
Wet/Dry Vac must be identical to the parts they replace. Your
double-insulated
Wet/Dry Vac is marked with the words "DOUBLE
INSULATED"
and the symbol
ance.
Key
No.
l--_--1(square
Part No.
within a square) may also be marked
1
2
509238
9-17816
3
4
5
9-16937
9-16938
826286
6
7
8
9
73185
822479
826285
73102
Drain Cap
Wheel
10
11
12
826387
826386
822442-1
Drum Latch
Lid
Gasket Lid
13
14
826388
820563-7
Power Head Latch
15
826383
16
17
18
19
20
826411
826389
822467-10
826382
823871
t Stock Item - Ma
stores.
Key
No.
Descdption
Cage Filter/Float
tFilter (Red Stripe)
tFilter Plate
t Filter Nut
Drum
Accessory
Caster
21
816345-1
22
23
24
15534-1
818413
818961
25
26
Caddy
* Screw Pan Hd. Ty
AB #10 x 314
Intake Shield
Part No.
822459-1
826404
27
28
822480
1822482
29
30
826385
815096
31
826356
on the appli-
Description
Nut-Hex Flange 114-20
Washer
Blower Wheel
Spacer
Collector Gasket
Motor (Includes Key
Nos.21, thru 24)
Blowing Diffuser
Blower Adapter
Motor Cover
Hose Adapter
THose 2 1/2" x 7'
(Includes Key Nos.
30 thru 33)
32 826355
33 826354
34 1822256
Foam Pad
Foam Pad Holder
SP6157
Cord w/Plug
Detachable Lid
Rocker Switch
Spring Tab
Hose End interlock
Squeegee
Owners Manual
(Not illustrated)
be secured through the hardware department of most Sears retail
* Standard Hardware
Item - May be purchased locally
16
Repair Parts
20
/5
6
17
CRRFTSMRN.
Accessories and Attachments
Get more versatility from your Craftsman wet]dry vacuum by adding these accessories.
Additional wet]dry vac accessodes may be purchased at your local Sears retail store
or Sears/Craftsman Power and Hand Tool Catalog.
17820 2-1/2"x7'
Hose
16922 Utility Nozzle
16978 Car Nozzle
16915 Multipurpose
Floor Tool
16947,
Inflator
NOTE:
16948
Nozzle
Most Accessories
16964 Extension
Wands
17817 Wet Nozzle
16933 Blower Nozzle
16926 t4" Floor
Brush
17816 Paper Pleated
Filter
Are Available
18
In 2-t/2
16991
Noise Muffler
16925 Dry Nozzle
16902 Crevice
Tool
16901 Dusting
Brush
17916 High Efficiency
Filter
Inch And 1-1/4 Inch Sizes
16934HoseGrip
16917Hose
Connector
16930HoseLock
16935Gutter Nozzle
Sawdust Collection Series
Whole-shop
Sawdust
Manifold-Type
29964
Collection
System
Table Saw Dust
Collection Kit
29962
Radial Arm Saw
Dust Collection Kit
29963
19
For the repair or-replacementparts you need
Call7 am-- 7 pro, 7 daysa week
1-800-366-PART
(1-800-366-7278)
For in-home major brand repair service
Call 24 hours a day,7 daysa week
1-8OO-4-REPAIR
(1-81)0-473-7247)
Fer the location of a
Seam Repair Service Center in your area
Call 24 hours a day,7 daysa week
BELIE
1-8OO-488-1222
Fw information on purchasinga Seam
Maintenance Agreementor to inquire
about an existing Agreement
Call9 am - 5 prn, M0nday-Saturday
1-8OO-827-6655
_--
__
SEARS
Arne_ca's Repair Specialists
The model number
When requesting
information:
will be found on the side of the power head.
service or ordering
• Product Type•
• Part Number.
parts, always provide the following
Model Number
Part Description
© 1998 Emerson Electric Co.
Seam,
Part No. SP6157
Roebuck
and Co., Hoffman
Estates,
Form No. SP6157
IL. 60179 U.S.A.
Printed in U.S.A. 8/98