Philips 42PES0001D Technical data

Register your product and get support at
www.philips.com/welcome
42PES0001D/H
EN LCD television
IT
Televisore LCD
________________________________ ________________________________
DE LCD-Fernsehgerät
ES
Televisor LCD
________________________________ ________________________________
FR
Téléviseur LCD
PT Televisor LCD
________________________________ ________________________________
NL LCD televisie
EL
TËÏÂfiÚ·Û˘ LCD
________________________________ ________________________________
Downloaded From TV-Manual.com Manuals
Downloaded From TV-Manual.com Manuals
1
1.1
1.2
1.3
Important 3
Safety 3
Care of the screen 3
Recycling 3
7
7.1
7.2
7.3
2
2.1
2.2
2.3
Your TV 4
Television overview 4
How to enjoy HD TV 5
Product highlights 5
7.4
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Getting started 5
Position the TV 5
Position the Essence Connectivity hub 5
Mount the speaker bar 6
Wall mounting 6
Lower the TV stand 6
Remote control batteries 7
Single cable between the TV hub
and the TV screen 7
Antenna cable 7
Power cable 7
4
4.1
4.2
4.3
4.4
4.5
4.6
Use your TV 8
Switch on or off - Standby 8
Watch TV 8
Watch channels from a digital receiver 9
Watch connected devices 9
Watch a DVD 9
Select a Teletext page 9
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
Use more of your TV 10
Remote Control 10
TV menus 11
Picture and sound settings 12
Teletext 15
Create favourite channel lists 17
Electronic Programme Guide 18
Timers and locks 19
Subtitles 20
Watch and play photos, MP3... 20
Listen to digital radio channels 22
Software update 23
6
6.1
6.2
6.3
6.4
6.5
6.6
Channel installation 25
Automatic channel installation 25
Manual channel installation 27
Rearrange stored channels 27
Channel management 28
Digital reception test 28
Factory settings 28
Table of contents
Downloaded
From TV-Manual.com Manuals
7.5
7.6
7.7
Connections (DVD, receiver, ...) 29
Connections overview 29
About connections 30
Connect your devices with the
Connection assistant 31
Connect your devices without the
Connection assistant 31
Connection setup 37
Preparing for digital services 37
PC network 38
8
Technical data 44
9
Troubleshooting 46
10
Index 49
ENGLISH
Table of contents
UK Digital TV switchover info 51
Register your product and get support at ...
www.philips.com/welcome
1
2008 © Koninklijke Philips Electronics
N.V. All rights reserved. Specifications
are subject to change without notice.
Trademarks are the property of
Koninklijke Philips Electronics N.V. or
their respective owners.
Philips reserves the right to change
products at any time without being
obliged to adjust earlier supplies
accordingly.
The material in this manual is believed
adequate for the intended use of the
system. If the product, or its individual
modules or procedures, are used for
purposes other than those specified
herein, confirmation of their validity
and suitability must be obtained. Philips
warrants that the material itself does
not infringe any United States patents.
No further warranty is expressed or
implied.
Warranty
No components are user-serviceable.
Never open or remove covers and
never insert objects in the ventilation
slots or insert objects not suitable for
the specific connectors. Repairs may
only be done by Philips Service
Centres and official repairshops. Failure
to do so shall void any warranty, stated
or implied.
Any operation expressly prohibited in
this manual, any adjustments, or
assembly procedures not
recommended or authorised in this
manual shall void the warranty.
Pixel characteristics
This LCD product has a high number
of colour pixels. Although it has
effective pixels of 99,999% or more,
black dots or bright points of light
(red, green or blue) may appear
constantly on the screen.This is a
structural property of the display
(within common industry standards)
and is not a malfunction.
Open source software
This television contains open source
software. Philips hereby offers to
deliver or make available, upon
request, for a charge no more than the
cost of physically performing source
distribution, a complete machinereadable copy of the corresponding
source code on a medium customarily
used for software interchange.
This offer is valid for a period of 3
years after the date of purchase of this
product.
To obtain the source code, write to
Philips Innovative Applications N.V.
Ass. to the Development Manager
Pathoekeweg 11
B-8000 Brugge
Belgium
Compliance with EMF
Koninklijke Philips Electronics N.V.
manufactures and sells many products
targeted at consumers, which, like any
electronic apparatus, in general have
the ability to emit and receive
electromagnetic signals.
One of Philips’ leading Business
Principles is to take all necessary
health and safety measures for our
products, to comply with all applicable
legal requirements and to stay well
within the EMF standards applicable at
the time of producing the products.
Philips is committed to develop,
produce and market products that
cause no adverse health effects.
Philips confirms that if its products are
handled properly for their intended
use, they are safe to use according to
scientific evidence available today.
Philips plays an active role in the
development of international EMF and
safety standards, enabling Philips to
anticipate further developments in
standardisation for early integration in
its products.
Mains fuse (UK only)
This TV is fitted with an approved
moulded plug. Should it become
necessary to replace the mains fuse,
this must be replaced with a fuse of
the same value as indicated on the
plug (example 10A).
1. Remove fuse cover and fuse.
2. The replacement fuse must comply
with BS 1362 and have the ASTA
approval mark. If the fuse is lost,
contact your dealer in order to
verify the correct type.
3. Refit the fuse cover.
In order to maintain conformity to the
EMC directive, the mains plug on this
product must not be detached from
the mains cord.
2
Downloaded
From TV-Manual.com Manuals
Copyrights
VESA, FDMI and the VESA
Mounting Compliant logo are
trademarks of the Video Electronics
Standards Association.
Manufactured under license
from Dolby Laboratories. ‘Dolby’, ‘Pro
Logic’ and the double D symbol G,
are trademarks of Dolby Laboratories.
Manufactured under
license from BBE Sound, Inc. Licensed
by BBE, Inc under one or more of the
following US patents: 5510752,
5736897. BBE and BBE symbol are
registered trademarks of BBE Sound
Inc.
Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States
and/or other countries
® Kensington and MicroSaver are
registered US trademarks of ACCO
World Corporation with issued
registrations and pending applications
in other countries throughout the
world.
DLNA®, the DLNA
logo and DNLA Certified™ are
trademarks, service marks, or
certification marks of the Digital Living
Network Alliance.
All other registered and unregistered
trademarks are the property of their
respective owners.
Important
Read this user manual before you start to use this
product.
Pay attention to this section and closely follow the
instructions. The warranty does not apply to
damage caused by not taking into account the
instructions.
1.1
Safety
• To avoid short circuit, never expose the product
to rain or water.
• To avoid a risk of fire or electric shock never
place naked flame sources (e.g. lighted candles)
close to the TV.
• Leave a space of at least 10 cm (4 inches) from
the rear and the top of the Essence Connectivity
hub and 5 cm (2 inches) from the left and right
for ventilation.
• Keep away from radiators or other heat sources.
• Never place the Essence Connectivity hub on
top of or underneath other devices that might
heat up (for ex. a receiver or an amplifier). Never
put anything under the TV hub.
• Install the TV hub near a wall socket where the
mains plug can be easily reached.
• To prevent damage, never insert any object into
the ventilation slots.
• Make sure the TV cannot fall down. Place the TV
on a solid and flat surface and only use the stand
provided with the TV.
• To prevent damaging the mains cord, never place
the TV, or anything else, on the cord. Damage the
cord may cause a fire or electric shock.
• When mounted on a swivel stand or wall bracket
avoid force coming on the mains plugs. Mains
plugs that are partly loosened can cause arcing or
fire.
1.2
• Never touch, push or rub or strike the screen
with anything hard as this may scratch, mar or
damage the screen permanently.
• To avoid deformations and colour fading, wipe off
water drops as soon as possible.
• Stationary images
Avoid stationary images as much as possible. If
you cannot, reduce screen contrast and
brightness to prevent damage to the screen.
Stationary images are images that remain on the
screen for a long time. Examples of stationary
images are: on screen menus, teletext pages, black
bars, stock market information,TV channel logos,
time displays, and so on.
1.3
Recycling
• Take the packaging to your local recycling centre.
• Your product is designed and manufactured with
high quality materials and components, which can
be recycled and reused. When you see the
crossed-out wheel bin symbol attached to a
product, it means the product is covered by the
European directive 2002/96/EC.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on separate collection of electrical
and electronic products. The correct disposal of
your old product helps prevent potentially
negative consequences for the environment and
human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be
disposed of with normal household waste. Please
inform yourself about the local rules on separate
collection of batteries. The correct disposal of
batteries helps prevent potentially negative
consequences for the environment and human
health.
Care of the screen
• Disconnect the TV from the mains before
cleaning.
• Clean the surface of the TV screen with a soft
damp cloth. When a damp cloth is insufficient, use
a special LCD screen cleaner. Never apply any
other substance (chemical or household cleaning
agent). This may damage the screen.
Important From TV-Manual.com Manuals
Downloaded
3
ENGLISH
1
2
Your TV
This section gives you an overview of the controls
and functions of this TV.
2.1
Television overview
Controls
Remote control
v
b
q
DEMO
Ï
1
2
3
4
5
Remote control sensor
Power switch
Program/Channel up and down
Menu
Volume up and down
Connectors
1
2
3
4
5
6
7
Switch On or switch to Standby
Programme guide
Volume up + or down Program/Channel up + and down Menu On or Off
Navigation and Rotary key
Colour keys
For more info see section 5.1 Remote control
overview.
1 Back connectors
2 Left side connectors
For more info see section 7 Connections.
4
Downloaded
From TV-Manual.com Manuals
Your TV
How to enjoy HD TV ?
This TV can display High Definition TV programmes.
But to enjoy HD TV you need to get programmes
in HD first. The picture quality of this TV without
HD programmes is just normal TV.
You can receive HD programmes from ...
- a Blu-ray Disc player, connected to HDMI, with a
HD Movie
- a digital HD receiver, connected to HDMI, with a
subscription to HD channels from a Cable or
Satellite company
- an Over-the-air HD broadcaster (DVB-T MPEG4)
- a HD channel on your DVB-C network
- a Game console (Xbox 360 / PlayStation 3),
connected to HDMI, with a HD game.
3
Get started
ENGLISH
2.2
This section helps you with the positioning and the
first time installation of the TV.
3.1
Position the TV screen
Carefully read the safety precautions in section 1.1
Safety before you position the TV.
• Large screen TVs are heavy. Carry and handle the
TV screen with at least two persons.
• The ideal distance from which to watch TV is
three times its diagonal screen size.
• Position the TV screen where light does not fall
directly on the screen.
• Your TV screen is equipped with a Kensington
Security Slot for an anti-theft lock (not supplied).
Contact your dealer for more information. Go to
www.philips.com/support FAQ’s to find the list of
HD channels or providers in your country.
2.3
Product highlights
Your new TV is equipped with some of the most
modern audio or video innovations.
Your TV offers the following advantages ...
Full High Definition LCD display
A full HD resolution of 1920x1080p, the highest
resolution of HD sources. It offers a brilliant flickerfree progressive scan picture with optimum
brightness and superb colours.
3.2
Position the Essence
Connectivity hub
DVB-T and DVB-C integrated tuner
Next to normal analogue TV broadcast your TV
receives digital terrestrial and in certain countries
also digital cable TV and radio broadcasts.
• Always place the TV hub in a horizontal position.
• Never install the TV hub in a closed space or
cupboard.
• Be aware the top side can become quite hot.
Carefully read the safety precautions in section 1.1
Safety before you position the Connectivity hub.
Electronic Programme Guide - EPG
The EPG shows the scheduled digital TV
programmes on screen. The guide can remind you
when programmes start, switch the TV on, etc.
USB connection / PC network connection
Multimedia connection for instantly view or play
your photos or music.
Your TV
Downloaded
From TV-Manual.com Manuals
5
3.3
Mount the speaker bar
You can mount the supplied attachable speaker bar
to the TV screen. See the supplied Start booklet.
You can also download this booklet from
www.philips.com/support.
3.4
Wall mounting
You can wall mount the TV screen with the
supplied wall mount bracket.
How to mount the TV screen, see the supplied
Start booklet. You can also download this booklet
from www.philips.com/support.
3.4.1 Mount the wall mount bracket
) Caution
Wall mounting the TV requires special skills that
should only be performed by qualified personnel.
Wall mounting the TV should meet safety standards
according to the TV’s weight.
Koninklijke Philips Electronics N.V. bears no
responsibility for improper mounting or mounting
that results in accident or injury.
3.4.3 Unmount the TV stand
The TV stand should be unmounted from the TV
screen to allow the TV screen to be wall mounted.
3.4.4 Mount the TV screen to the wall
How to mount the TV screen to the wall, see the
supplied Start booklet. You can also download this
booklet from www.philips.com/support.
3.5
Lower the TV stand
You can lower the TV screen on the stand when
you do not mount the attachable speaker bar.
See the supplied Start booklet. You can also
download this booklet from
www.philips.com/support.
Read also the safety precautions in section
1.1 Safety before you position the TV.
3.4.2 VESA compliant wallmounting
The TV is prepared for VESA compliant wall
mounting. This bracket is not included.
Use a VESA compliant bracket with code
VESA MIS-F, 300, 300, 8.
Prepare for VESA wallmounting
‡ Locate the four fixation points at the back of
the TV.
® Should the plastic discs obstruct the VESA
bracket, you can unscrew these 4 discs.
x4
6
Downloaded
From TV-Manual.com Manuals
Your TV
Remote control batteries
) Caution
This product contains lithium batteries. There is
danger of explosion if the batteries are incorrectly
replaced. Replace only with the same or equivalent
type.
3.8
Antenna cable
‡ Locate the antenna connection at the back of
the TV hub.
® Insert the antenna cable tightly into the
Antenna x socket.
‡ Open the battery cover on the back of the
remote control.
® Make sure the + and sides of the batteries line
up correctly (inside of case is marked.)
Ò Close the cover.
ANTENNA
3.9
rNote
Remove the batteries if not using the remote
control for an extended period of time.
3.7
Single cable between the
TV hub and the TV screen
‡ Insert the supplied Essence Single cable into the
respective connectors at the back of the TV
hub and at the back of the TV screen.
Use your TVFrom TV-Manual.com Manuals
Downloaded
ENGLISH
3.6
Power cable
Keep the mains plug at the wall socket accessible at
all time.
The TV is never powered off completely and
consumes energy unless the mains cord is physically
unplugged.
Although this TV has a very low standby power
consumption, unplug the mains cord if you do not
use the TV for a long time to save energy.
‡ Verify that your mains voltage corresponds with
the voltage printed on the sticker at the back of
the TV hub. Never insert the mains cord if the
voltage is different.
® Insert the mains cord tightly.
7
4
4.2
Use your TV
Learn how to operate your TV for daily use.
4.1
Switch on or off - Standby
rNote
The TV may take up to 15 seconds to turn on.
To switch on the TV:
• Press B Power at the front of the TV hub if the
standby indicator is off.
• Press B on the remote control if the standby
indicator is on.
Watch TV
4.2.1 Switch channels
‡ To switch TV channels:
• Press a number (1 to 999) or press P+ or Pon your remote control.
• Press Program/Channel - or + on the side
controls of the TV hub.
® Press R to return to the previously viewed TV
channel or connected device.
Ï
To switch to standby:
• Press B on the remote control.
To switch off:
• Press B Power at the front of the TV hub.
4.2.2 Adjust volume
‡ To adjust the volume:
• Press V + or - on the remote control
• Press Volume + or - on the side controls
of your TV hub.
® To mute the sound:
• Press ¬.
• Press ¬ again to restore the sound.
Ï
v
b
q
DEMO
8
Downloaded
From TV-Manual.com Manuals
Use your TV
Watch channels from a
digital receiver
‡ Switch on the digital receiver.
The picture from your receiver automatically
appears on the screen.
® Use the remote control of your digital receiver
to select TV channels.
If the picture does not appear:
‡ Press the Source v key.
® Press o or œ to select where you connected
your digital receiver.
Ò Press OK.
4.5
‡ Switch on your DVD player.
® Insert a DVD disc in your player.
The DVD picture automatically appears on the
screen.
Ò Press Play πon the DVD player.
If the picture does not appear:
‡ Press the Source v key.
® Press o or œ to select where you connected
your DVD player.
Ò Press OK.
Wait a few seconds until the picture appears.
† Press Play π.
4.6
v
b
q
DEMO
rNote
When you did not connect your devices yet, go to
section 7 Connections.
4.4
Watch connected devices
‡ Switch on the device.
The picture from your device automatically
appears on the screen.
If the picture does not appear:
® Press the Source v key.
Ò Press o or œ to select where you connected
your device.
† Press OK.
rNote
When you did not connect your devices yet, go to
section 7 Connections.
Watch a DVD
ENGLISH
4.3
Select a Teletext page
Most TV channels broadcast information through
Teletext.
To watch Teletext:
‡ Press Teletext.
The main index page appears.
® To select a page of your choice:
• Enter the page number with the number keys.
• Press P- or P+ or o or œ or the g key to
view the next or the previous page.
• Press a colour key to select one of the colour
coded items at the bottom of the screen.
• Press R to return to the previously viewed
page.
Ò Press Teletext again to switch Teletext off.
v
b
q
DEMO
rNote
Only for UK: some digital TV channels offer
dedicated digital text services (for example BBC1).
For more information on teletext, see section 5.4
Teletext.
Use your TVFrom TV-Manual.com Manuals
Downloaded
9
5
Use more of your TV
This section helps you perform advanced TV
operations including how to:
• use the menus
• adjust picture and sound settings
• make use of Teletext
• create favourite channel lists
5.1
Remote control
5.1.1
Remote control overview
•
•
•
•
make advantage of Electronic Programme Guide
set locks and timers
set subtitles and select a subtitle language
view your photos or play your favourite music
from a USB memory device or from your PC or
Home network.
1
Standby B
To switch the TV on or back to standby.
Source v
• To switch the Source menu on or off.
• To select a connected device or to return to
TV.
Teletext
To switch teletext on or off.
Colour keys
• Easy selection of teletext pages.
• Easy selection of tasks.
Demo
To switch the Demo menu on and to get a
demonstration of the features of the TV.
Guide a
To switch on or off the Electronic Programme
Guide.
Navigation and rotary key
To navigate (o, œ, p, π) or turn left or right
to go through lists or settings.
2
v
b
q
3
DEMO
4
5
Ï
6
7
8
9
10
11
12
13
14
10
Downloaded
From TV-Manual.com Manuals
OK
• To display the channel list.
• To activate a setting.
Back key g
To select the previous programme or the
previous TXT page.
To remove the channel list.
Volume V
To adjust the volume.
Mute ¬
To mute the sound or restore it.
Number keys
To select a TV channel.
MHEG Cancel (only for UK)
To cancel only Digital text or Interactive
services.
Previous channel R
To return to the previously viewed channel.
Use more of your TV
5.2
TV menus
ENGLISH
15 +P- Channel up or down
To switch to the next or previous channel in
the channel list.
16 Menu Ï
To switch the menu on or off.
17 On screen information INFO
To show channel or programme information if
available.
18 Dual screen b
To show teletext on the right and the picture
on the left of the screen.
19 Subtitle
To activate or deactivate the subtitle mode.
20 Widescreen Picture format q
To select a picture format.
With the on screen menus you install your TV,
adjust picture and sound settings and access
features. This section gives an overview of the
menus and describes how to navigate.
5.2.1 The menu
‡ Press Menu Ï to show the TV menu.
® Press Menu Ï to quit the TV menu.
Ï
Ï
See section 10 Index to find the section in the
manual about a specific remote control key.
The TV menu offers the following items:
TV menu
Smart settings
Picture
Sound
Settings assistant
Features
Setup
• Smart settings
Select this item to set the TV to one of the
predefined settings. Each setting combines picture
and sound.
• Picture
Select this menu item to adjust all picture
settings.
• Sound
Select this menu item to adjust all sound settings.
• Settings assistant
Use the Settings assistant to guide you through
basic picture and sound settings in an easy way.
• Features
Select this item for other feature settings.
• Setup
Select this item
- for installation and to update the TV software;
- to use the connection assistant which will help
you to connect your devices to the TV hub.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
11
5.2.2 Use of the menu
Learn to use the menus with this example.
‡ Press Menu Ï.
The TV menu appears on the screen.
rNote:
More choices come available when digital channels
are installed and broadcasted.
5.3
TV menu
Smart settings
Picture
Picture and Sound settings
The first time you switched on the TV you have
selected your preferred settings for picture and
sound. The following sections describe how to
modify or read just those settings.
Sound
Settings assistant
Features
Setup
® Press o or œ to select Picture.
ÒPress π to enter the picture settings.
Picture
Contrast
Contrast
Brightness
90
47
Colour
Hue
52
0
Sharpness
4
Noise reduction
Tint
...
† Press œ to select Brightness.
Picture
Brightness
Contrast
Brightness
98
47
Colour
Hue
52
0
Sharpness
4
Noise reduction
Tint
...
5.3.1 Smart settings
Sets the TV to one of the predefined settings. Each
setting combines picture and sound.
‡ Press Menu Ï and select Smart settings.
® Press π to enter the list.
Ò Press o or œ to select a setting.
† Press OK.
º Press Menu Ï to quit the TV menu.
Smart settings: Personal, Vivid, Standard, Movie,
Energy saving, Game.
5.3.2 Settings assistant
Use the Settings assistant to guide you through
basic picture and sound settings in an easy way.
‡ Press Menu.
® Select Settings assistant and press π to enter.
Ò Press the green key to start the assistant.
† Press p or π to select the left or right side to
make your choice.
º Press the green key to go to the next setting.
Go through several settings.
◊When finished, press the green key to store all
your settings.
º Press π to enter the brightness setting.
Brightness
◊Press o or œ to adjust the setting.
‹Press p to return to the Picture settings or
press Menu Ï to quit the TV menu.
12
Downloaded
From TV-Manual.com Manuals
Use more of your TV
Picture
Perfect Pixel HD
...
Noise reduction
HD Natural Motion
Tint
100 Hz Clear LCD
Advanced sharpn...
Perfect Pixel HD
Dynamic contrast
ENGLISH
5.3.3 Picture settings
This section describes how to adjust all picture
settings individually.
‡ Press Menu Ï.
® Select Picture and press π to enter the list.
Ò Press o or œ to select a setting.
Active control
TV menu
Picture
Picture format
MPEG artefact red...
Smart settings
Picture
Contrast
Brightness
Auto format mode
Colour enhance...
Sound
Colour
Hue
Features
Sharpness
Setup
Noise reduction
Tint
Perfect Pixel HD
Active control
Picture format
Auto format mode
• Contrast
Changes the level of bright parts in the picture
but keeps the dark parts unchanged.
• Brightness
Changes the level of light of the total picture.
• Colour
Changes the level of saturation.
• Hue
If NTSC is broadcasted, this level compensates
the colour variations.
• Sharpness
Changes the level of sharpness of fine details.
• Noise reduction
Filters out and reduces the noise in the picture.
Set the level to Minimum, Medium, Maximum or
Off.
• Tint
Sets the colours to Normal, Warm (reddish) or
Cool (bluish). Select Custom to make a setting of
your own in the Custom menu.
• Custom
Press the green key to select each bar to
change the value of:
- R-WP red whitepoint
- G-WP green whitepoint
- B-WP blue whitepoint
- R-BL red blacklevel
- G-BL green blacklevel
• Perfect Pixel HD
Controls the advanced settings of the Perfect
Pixel HD Engine, resulting in best sharpness,
contrast, colour and motion.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
- HD Natural Motion
Removes motion judder and reproduces
smooth movement especially in movies.
- 100 Hz Clear LCD
Gives a superior motion sharpness, better black
level, high contrast with a flicker-free, quiet
image and a larger viewing angle.
- Advanced sharpness
Enables superior sharpness, especially on lines
and contours in the picture.
- Dynamic contrast
Sets the level at which the TV automatically
enhances the details in dark, middle and light
areas of the picture.
- Dynamic backlight
Sets the level at which power consumption can
be reduced by dimming the brightness intensity
of the screen.
Choose for the best power consumption or for
the picture with the best brightness intensity.
- MPEG artefact reduction
Smooths the digital transitions in the picture.
- Colour enhancement
Makes the colours more vivid and improves the
resolution of details in bright colours
• Active control
Corrects all incoming signals in order to provide
the best picture possible.
Switches Active control on or off.
• Picture format / Auto format mode
See section 5.3.4 Widescreen picture format.
13
5.3.4 Widescreen picture format
Avoid black bars on the sides or on top and
bottom of the picture. Change the picture format
to a format that fills the screen.
‡ Press q to switch on the Picture format
menu.
v
b
q
DEMO
® Press o or œ to select an available picture
format.
Ò Press OK.
† Press o to shift the picture upwards if subtitles
are hidden.
à Tip
For minimal distortion, select the Auto format
setting.
• Auto format (Not for PC.)
Enlarges the picture automatically to fill the
screen. Subtitles remain visible. You can set Auto
format in two different modes.
‡ In the TV menu, select Picture > Auto format
mode.
® Select Auto-fill to fill the
screen as much as
possible. Select Autozoom to keep the original
picture format but black
bars may be visible.
• Movie expand 16:9
(Not for HD.)
Scales the format to 16:9.
• Wide screen
Stretches the format to
16:9.
• Unscaled
(Only for HD and PC.)
Maximum sharpness.
Distortion may appear on
borders. Black bars may
appear with pictures from
your PC.
rNote
Never forget to name the connection in the
Connection menu. See section 7.5.1 Naming your
devices.
5.3.5 Sound settings
This section describes how to adjust all sound
settings.
‡ Press Menu Ï and select Sound.
® Press π to enter the list.
Ò Press o or œ to select a setting.
TV menu
Sound
Smart settings
Picture
Equalizer
Volume
Sound
Volume - Visually...
Settings assistant
Balance
Features
Audio language
Setup
Dual I/II
Mono/Stereo
• Super zoom (Not for HD.)
Removes the black bars on
the side of 4:3 broadcasts.
There is a minimal
distortion.
• 4:3 (Not for HD.)
Shows the classical 4:3
format.
• Movie expand 14:9
(Not for HD.)
Scales the format to 14:9.
14
Downloaded
From TV-Manual.com Manuals
TV speakers
Surround mode
Headphone volume
Auto volume level...
Delta volume
Auto surround
• Equalizer
Changes the bass and treble of the sound. Select
each bar to change the setting.
• Volume
Changes the volume. When adjusting the volume
with V a volume bar appears. If you do not
want it to appear go to Menu > Setup >
Installation > Preferences and press π to enter
the list and select Volume bar off.
Use more of your TV
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
5.4
Teletext
Your TV has a 1200 pages memory that stores
broadcasted teletext pages and subpages to reduce
waiting time.
To select a teletext page see section 4.6 Select a
Teletext page.
5.4.1 Select a teletext language
Some digital TV broadcasters offer the possibility to
select your preferred teletext language. See section
6.1 Automatic installation.
5.4.2 Select pagenumber subpages
A teletext page number can hold several subpages.
The pages are shown on a bar next to the main
pagenumber.
‡ Press Teletext.
® Select a teletext page.
Ò Press p or π to select a subpage.
v
b
q
DEMO
5.4.3 Select T.O.P. teletext broadcasts
T.O.P. teletext (Table of Pages) is not broadcast by
all TV channels. You can easily jump from one
subject to another without using pagenumbers.
‡ Press Teletext.
® Press INFO.
The T.O.P. overview appears.
Ò Use p or π, o or œ to select a subject.
† Press OK to view the page.
v
b
q
DEMO
15
ENGLISH
• Volume – Visually impaired (UK only)
Changes the volume of the selected Visually
impaired audio language in the Setup, Installation
menu. See section 6.1 Automatic installation.
• Balance
Sets the balance of the left and right
loudspeakers to fit best your listening position.
• Audio language
A list of audio languages for the current
programme may be available when digital
channels are installed and broadcasted.
To permanently change the audio language, see
section 6 Channel installation.
• Dual I/II
If broadcasted, you can choose between two
different languages.
• Mono/stereo
If stereo broadcasting is available, you can select
Mono or Stereo per TV channel.
• TV speakers
If you have connected an audio system to the TV
hub, you can switch off the speaker bar.
If your audio system supports Easylink, see
section 7.2.2 Easylink.
Select Automatic to have the sound from your
TV automatically reproduced by your audio
system.
• Surround mode
To select a more spatial sound if broadcasted or
if available from a connected device.
• Headphone volume
Changes the volume of the headphone.
You can mute the speaker bar with ¬ on the
remote control.
• Auto volume levelling
Reduces sudden volume differences like at the
beginning of commercials or when switching from
one channel to another.
Select on or off.
• Delta volume
Levels out volume differences between channels
or connected devices.
‡ Switch to the channel or device you want to
level out the volume difference.
® Select Delta volume in the Sound menu and
change the volume level.
• Auto surround
Switches the TV automatically to the best
surround sound mode dependant on the
broadcast.
Select on or off.
5.4.4
Dual screen teletext (not available for
channels with Digital Text services)
View the TV channel and teletext next to each
other.
‡ Press b for Dual screen teletext.
® Press Teletext again to show normal teletext.
Ò Press Teletext to switch off teletext.
• Language
Some languages use a different set of characters.
Switch to the other group to show the text
correctly.
‡ Press Teletext.
® Press Menu Ï.
Teletext menu
5.4.5
Search teletext
Quickly jump to a subject linked to a series of
pagenumbers or search for specific words in
teletext pages.
‡ Press Teletext.
® Press OK to highlight the first word or number.
Ò Press p or π, o or œ to jump to the next
word or number on the page.
† Press OK to search a page which holds the
highlighted word or number.
º Press o until no word or number is highlighted
to quit Search.
5.4.6 Enlarge teletext pages
For a more comfortable reading, you can enlarge
the teletext page.
‡ Press Teletext and select a teletext page.
® Press q to enlarge the top part of the page.
Ò Press q again to view the enlarged lower
part of the page.
† Press o or œ to scroll through the enlarged
page.
º Press q again to return to the normal page
size.
v
b
q
DEMO
5.4.7 Teletext menu
With the options in the teletext menu you can
reveal hidden info, let cycle subpages automatically
and change the character setting.
• Reveal
Hide or unhide hidden information on a page,
such as solutions to riddles or puzzles.
• Cycle subpages
If subpages are available for the selected page,
you can make subpages cycle automatically.
16
Downloaded
From TV-Manual.com Manuals
Reveal
Off
Cycle subpages
Off
Language
Gr. II
Ò Press o or œ to select an option.
† Press OK to change a setting.
º Press Menu Ï to quit the teletext menu.
◊Press Teletext to switch off teletext.
5.4.8
Digital text services (UK only)
Some digital TV broadcasters offer dedicated digital
text or interactive services (for example BBC1) on
their digital TV channels. These services work as
normal Teletext with the number, colour and
navigation keys to select and navigate.
‡ Press Teletext.
® Press p or π, o or œ to select or highlight
items.
Ò Press one of the colour keys to select an
option.
† Press OK to confirm or activate.
º Press MHEG Cancel to cancel Digital text or
interactive services.
ç Caution
Digital text services are blocked when subtitles are
broadcasted and Subtitle On is set in the Features
menu. See section 5.8 Subtitles.
5.4.9 Teletext 2.5
If broadcasted by the TV channel this teletext offers
more colours and better graphics.
Teletext 2.5 is switched on as a factory setting.
‡ Press Menu Ï on the remote control and
select Setup > Installation > Preferences >
Teletext 2.5 and press π to enter the list.
® Select on or off.
Use more of your TV
Create favourite channel
lists
View the All channels list or set up a Favourite list
of your own with your preferred TV channels and
radio stations.
5.5.1 Select a favourite list
You can select one of the favourite channel lists.
‡ Press OK.
The first time after you have finished the
installation, the All channels list is shown. In
other situations, it brings up the last selected
favourite list.
5.5.3 Select a channel from a favourite list
‡ Press OK.
The last selected channel list appears.
® Use o or œ to highlight a channel.
Ò Press OK.
The TV tunes to that channel.
à Tip
• Use -P+ to go through the TV channels of the
selected favourite list.
• With the number keys you can still select
channels which are not marked as favourite.
All channels
....
EXT 3
A
1 Analogue channel 1
2 Digital channel 1
-
3 Digital channel 2
4 Radio channel 1
....
Select list
® Press the red key to show all favourite lists.
Ò Press o or œ to select a list.
† Press OK.
The selected favourite list appears.
º Press OK again to quit.
5.5.2 To set up a favourite list
Create or modify your own favourite list.
‡ Press OK.
The last selected list appears.
® Press the red key to show all favourite lists.
Ò Press o or œ to select a list.
† Press OK.
º Press the green key to enter the Edit mode.
The selected list brings up a full channel list.
◊Press o or œ to highlight a channel.
‹ Press OK to mark (or unmark) the highlighted
channel. The channel is added to (or removed
from) the selected list.
≈Press the green key again to leave the Edit
mode.
The modified channel list appears again.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
17
ENGLISH
5.5
5.6
Electronic Programme
Guide - EPG -
The Electronic Programme guide is an on screen
guide to scheduled digital TV programmes.
You can navigate, select and view programmes by
time, title or genre. There are two types of EPG,
‘Now and Next’ and ‘7 or 8 day’ EPG.
Programme guide
Tue., 12 Sep
Around
09:55
BBC ONE
07:50 Commonwealth
12:30 Commonwealth
BBC TWO
09:50 Tweenies
10:15 Something Special
five
09:00 The Wright Stuff
10:30 Trisha Goddard
BBC THREE 05:32 This is BBC THREE
BBC FOUR
05:32 This is BBC FOUR
abc1
09:20 Moonlighting
Remind
When digital channels are installed and
broadcasted, EPG is available. ‘Now and Next’ is
always available but the ‘7 or 8 day’ EPG is only
available in some countries.
With the EPG menu you can...
• see a list of current broadcasted programmes
• see the next programme
• group programmes by genre
• set reminders when programmes will start
• set up preferred EPG channels
• etc.
5.6.1 Switch on EPG
‡ Press a.
Watch
13:50 Anastasia
12:00 This is BBC THREE
12:00 This is BBC FOUR
10:15 Daddio
Jump to ...
Info
0010 - EEN
® Use the colour keys to activate the available
actions at the bottom of the screen.
• Next: to show information about the next
programme.
• Remind: to mark or unmark a programme as a
reminder.
• Watch: to watch or listen to a current
programme.
• Jump to...: to jump to the next or previous day.
• Info: to display information on a selected
programme (if available).
Ò Press a to quit the EPG.
5.6.2
More on ‘7 or 8 day’ EPG
Search by genre, scheduled reminders, etc. are
managed in the Programme guide menu.
‡ Press a on the remote control.
® Press Menu Ï.
The Programme guide menu appears.
v
b
Next
q
DEMO
Programme guide
What's on
What's on
The following type of EPG appears:
‘Now and Next’ EPG
Detailed information about the current programme
is shown.
26 BBC1
Tue., 12 Sep
12:30 South Today
11:50 Working Lunch
Search by genre
Scheduled remind... 11:55 Melrose Place
Preferred EPG ch... 13:00 In aller Freund
Acquire EPG data
09:17
Title : Commonwealth Games
Info: 7:50 - 12:30 : 280 min
..........
Exit
Next
Press -P+ to change channel.
Or
‘7 or 8 day’ EPG
It may take some time to receive the EPG data.
The list of TV programmes will show.
18
Downloaded
From TV-Manual.com Manuals
Ò Press o or œ to select a menu option.
† Press π to enter.
º Press o or œ to make a selection.
◊Press OK to activate or press the green key to
watch
‹ Press a to quit the EPG.
rNote
Only channels marked as Preferred EPG channels
appear in the Programme guide menu.
Use more of your TV
Timers and locks
This section describes how to switch the TV on or
off at a specified time and to lock or unlock the TV.
5.7.1 Automatically switch to standby
Sleeptimer switches the TV to standby after a time.
‡ Press Menu Ï on the remote control and
select Features > Sleeptimer and press π to
enter the sleeptimer bar.
® Press o or œ to set the time up to 180
minutes in steps of 5 minutes. If set to 0
minutes, the Sleeptimer is switched off.
You can always switch off your TV earlier or reset
the time during countdown.
5.7.2 Automatically switch the TV on
On timer switches the TV on automatically to a
specified channel at a specified time, from standby.
‡ Press Menu Ï on the remote control and
select Features > On timer and press π to
enter the On timer menu.
® Use p or π, o or œ to select and enter the
menu items one by one to set a channel, a day
of the week or daily, and a starting time.
Ò Press OK to confirm.
† Press Menu Ï to quit the menu.
à Tip
To switch off the On timer, select Off in the On
timer menu.
5.7.3 Lock TV channels and programmes
Lock TV channels and/or programmes from
connected devices to prevent children from
watching them. Lock and unlock with a four number
code.
Set or change your code
‡ Press Menu Ï on the remote control and
select Features > Set or Change code and press
π to enter your code.
® Enter your code with the number keys.
The Features menu reappears with a message
confirming that your code has been created or
changed.
Did you forget your code ?
‡ Select Change code.
® Press π.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
Ò Enter the overriding code 8-8-8-8.
† Enter a new personal code.
º Confirm your new entered code.
The previous code is erased and the new code
is stored.
5.7.4 Activate or deactivate Child lock
Set your code and you can:
• Lock all channels and devices,
• Lock specific channels and devices,
• Set a time after which all channels and devices
are locked,
• Set the maximum allowed parental rating for
digital channels that are installed and broadcast.
‡ Press Menu Ï.
® Select Features > Child lock and press π.
Ò Enter your code with the number keys.
† Select one of the options.
º Press π.
Lock or unlock all channels and connected devices
‡ Select Lock or Unlock.
Lock a certain programme or all channels from a
certain time
Child lock
Custom lock
Lock
Custom lock
Lock after
Channel lock
Unlock
Parental rating
‡ Select Custom lock.
® Press π to enter the Custom lock menu.
Ò Press π again to enter the Lock after menu.
† Select On to switch on the Timer lock.
º Press p.
◊Select Time.
‹ Press π.
≈Enter the time with o or œ and π.
Ú Press OK.
Lock one or more channels and connected devices
‡ Select Custom lock.
® Press π to enter.
Ò Press o or œ to select Channel lock.
† Press π.
º Press o or œ to select the channel(s) you
want to lock or unlock.
◊Each time press OK to lock or unlock the
channel.
19
ENGLISH
5.7
Set an age rating to a digital programme
Some digital broadcasters have their programmes
rated (depending on your country). When the
rating is higher than your child’s age, the
programme will be locked.
‡ Select Custom lock.
® Press π to enter.
Ò Press o or œ to select Parental rating.
† Press π.
º Press o or œ to select an age rating.
◊Press Menu Ï to quit the Child lock menu.
5.8.3 Select a digital subtitle language
If subtitle broadcasting is available with digital
channels, you can select a preferred subtitle
language out of a list of broadcasted languages. The
preferred subtitle languages set in the Installation
menu are overruled temporarily.
‡ Press Menu Ï on the remote control and
select Features > Subtitle language and press π
to enter the list of available languages.
® Press o or œ to select a subtitle language.
Ò Press OK.
5.8
5.9
Subtitles
For each TV channel, subtitles can be set, coming
from Teletext or digital broadcasts.
If digital channels are installed and broadcasted, you
can select your preferred subtitle language.
5.8.1 Subtitling from analogue TV channels
‡ Select an analogue TV channel.
® Press Teletext to switch on Teletext.
Ò Enter the three number pagenumber of the
subtitle page.
† Press Teletext to switch off Teletext.
rNote
The Teletext subtitle page of analogue channels
must be stored for each TV channel separately.
5.8.2 Activate or deactivate subtitling
‡ Press Menu Ï on the remote control and
select Features > Subtitle and press π to enter
the list.
® Press o or œ to select On to show the
subtitles always or On during mute to show the
subtitles only when the sound is muted with the
¬ key on the remote control.
Ò Press p to return to the Features menu.
TV menu
Features
Smart settings
Picture
Subtitle
Subtitle language
Sound
Sleeptimer
Watch and play your
photos and music
Watch pictures or listen to music stored on a USB
device (not supplied with the TV), a camcorder
(only for photos) or from your PC network. Watch
your pictures as a slideshow or listen to a self made
music playlist.
rNote
Philips is not responsible if your USB device is not
supported nor shall Philips accept any liability for
damage or loss of stored data.
5.9.1 Insert the USB device
‡ Insert a device at the side of the TV hub while
the TV is switched on.
A message appears that a USB device has been
detected.
rNote
In case the USB device does not automatically
break in, press Source v > USB/Memory devices
and press OK.
Select Side and press OK to display your
camcorder content.
5.9.2 Remove the USB device
‡ Press Source v.
® Remove the USB device.
Ò Select TV or another connected device to
watch a programme.
Child lock
Features
Set/Change code
Setup
On timer
Common interface
Demo
20
Downloaded
From TV-Manual.com Manuals
Use more of your TV
Watch your pictures, start a
slideshow and play music
Look up your pictures in the Picture album of your
USB device.
‡ Select the Picture folder for the picture files you
have stored on your USB device.
Afrika_2001
Paris_2006
My_car.jpg
Jean.jpg
Mary.jpg
® Press π to enter the Picture folder.
Ò Press o or œ to select a picture or a picture
album.
Picture
Afrika_2001
Afrika_2001
Paris_2005
My_car.jpg
Jean.jpg
Kenya.jpg
Congo.jpg
Victoria.jpg
Mary.jpg
Cairo.jpg
Afrika_2001
USB
Afrika_2001
Kenya.jpg
Kenya.jpg
Afrika_2001
Kenya.jpg
Congo.jpg
Victoria.jpg
Dakar.jpg
Thumbnails
Watch the pictures of a selected album in an
overview.
‡ Select a picture album.
® Press π to enter the picture list.
Ò Press the blue key.
† Press o or œ, p or π to highlight a picture.
º Press OK to watch the picture.
◊Press p to return to the thumbnail overview.
‹ Press the blue key again to go back to the
picture list.
—
Picture
Music
Picture
—
USB
• Slide time
Sets the time lag for the picture transitions:
Short, Medium or Long.
• Rotate
To rotate a picture.
• Start/Show/Pause
To stop, pause and restart the slideshow.
ENGLISH
5.9.3
Kenya.jpg
Cairo.jpg
† Press OK to watch the picture or to start a
slideshow of the pictures in the album.
º Press OK to pause the slideshow. Press again to
restart.
◊Press one of the colour keys on the remote
control to perform the corresponding function
shown at the bottom of the screen.
If the function bar at the bottom disappeared,
press any colour key to let it reappear.
‹ Press p and select another picture or another
album.
Slideshow settings
• Details / More details
Shows the picture name, date, size and next
picture in the slideshow.
• Transitions
Shows the list of available transition styles of the
pictures.
Press o or œ to select and press OK to
activate.
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
Listen to music
Look up your songs in the Music album of your
USB device.
‡ Select the Music folder for the music files you
have stored on your USB device.
® Press π to enter the Music folder.
Ò Press o or œ to select a song or a music
album.
† Press OK to play the selected song or to play a
song followed by the next song in the same
album.
º Press one of the colour keys on the remote
control to perform the corresponding function
shown at the bottom of the screen.
If the function bar at the bottom disappeared,
press any colour key to let it reappear.
Music settings
• Details
Shows the file name.
• Repeat one/all
Repeat all songs in the album until you stop a
song or only repeat the one song selected until
you stop the song.
• Shuffle
Play songs in a random sequence.
21
Watch a slideshow with background music
Watch a slideshow of your stored pictures
accompanied with your stored background music.
‡ Select an album of songs first and press OK.
® Highlight the Picture folder and select an album
of pictures and press OK.
5.9.4
Watch photos or listen to music from
your PC
To watch photos and listen to music from a
connected PC, make sure:
- your router and PC are switched on
- a media server software is running on your PC.
See section 7.7 PC network.
‡ Press the Source v key on the remote
control.
® Select PC network and press π.
Wait until the PC content comes on.
Ò Select the content you want to watch or listen
to and press π.
† Use p or π, o or œ to go through the
photo or music files or folders.
º Press OK to watch or listen.
◊Press p to go back to the previous list.
See section 9 Troubleshooting in case of problems
playing files or in case your PC does not appear in
the PC network menu.
5.10 Listen to digital radio
channels
If digital broadcasting is available, digital radio
channels are installed during installation.
To listen to a digital radio channel:
‡ Press OK on the remote control.
The All channels menu is displayed.
® Use the number keys to select a radio channel
available from channel number 400 onwards.
To reorder see section 6.3.3 Reorder the
channels.
Ò Press OK.
22
Downloaded
From TV-Manual.com Manuals
Use more of your TV
Philips continually tries to improve its products. To
benefit, update the TV software regularly. To update
your TV software you need a USB Memory device
(not supplied).
Verify that your USB memory device has at least
128Mb free space. Make sure the write protection
is switched off. Some USB devices do not work
with our TV.
5.11.1 Update assistant
The Update assistant helps you to update the TV’s
software.
Step 1:TV identification
The TV has to identify with your USB memory
device.
‡ Press Menu Ï > Setup.
® Press π.
Ò Press o or œ to select Software update.
† Press π.
Setup
Software update
Installation
Update assistant
Current software ...
Software update
Local updates
Announcement
º Press o or œ to select Update assistant.
◊Press π.
‹Press OK to activate.
≈Insert a USB memory device into the USB
connector at the side of the TV hub.
Ú Press the green key to proceed.
A message appears that the TV has successfully
written its identification file to the USB memory
device.
œ Press the green key again to finish.
π Remove the USB memory device from the TV
hub.
Step 2: Software download from the PC to
the USB device
‡ Insert the USB memory device into a PC linked
to the internet.
® Locate and open the file update.htm on your
USB device.
Ò Read the instructions on screen and click on
the Send ID button.
If new software is available, the update is
downloaded on the USB memory device.
† Remove the USB memory device from your
PC.
Step 3: Software update transfer to the TV
The downloaded software on the USB memory
device must now be uploaded to your TV.
ç Caution
• Never remove the USB memory device from the
TV during the software update.
• If a power drop occurs during the update, never
remove the USB memory device from the TV
hub. When the power returns, the TV continues
to update.
‡ Switch on the TV.
® Insert the USB memory device to the USB
connector at the side of the TV hub.
USB
Ò The TV switches off. The screen stays black for
about 10 seconds. Wait and never use the
power switch B on the TV hub.
USB
Use more ofFrom
your TVTV-Manual.com Manuals
Downloaded
23
ENGLISH
5.11 Software update
† The update process starts automatically. Please
wait.
‹ The TV switches off. The screen stays black for
about 10 seconds. Please, wait.
≈The TV switches back on again. The update is
done.
USB
The update is finished when the message
‘Operation successful’ appears on the screen.
Pr
g
Operation Successful! Re
USB
º Remove the USB memory device from the TV
hub.
5.11.2 Software update by digital broadcast
(DVB-T)
Your TV might receive new software from the
digital broadcast system automatically.
If you receive an update message on screen it is
strongly advised to update the software
immediately - select Now.
If you want to be reminded later on, select Later.
Select Cancel to quit the update (not
recommended). If you cancelled the update you can
still update yourself from the TV menu > Setup >
Software update > Local updates.
USB
◊Press B on the remote control.
Never press more than once and never use the
Power B switch on the TV hub.
v
b
q
DEMO
24
Downloaded
From TV-Manual.com Manuals
Use more of your TV
Channel installation
The first time you switched on your TV
• you have selected the language of the TV menus
and the country where you are located
• all the available TV Channels have been installed.
This chapter provides instructions on how to
reinstall channels as well as other useful channel
installation features.
rNote:
Re-installation will modify the All channels list and
new added channels will not be added to any
favourite list.
6.1
Automatic installation
This section describes how to search for and store
all available channels automatically.
Step 1: Menu language
Sets the language of the TV menus. Go to a next
step if your language settings are correct.
‡ Press Menu Ï on the remote control and
select Setup > Installation > Languages and
press π to enter Menu language.
® Press o or œ to select your language.
Ò Press OK to confirm.
† Press p to return to the Installation menu.
Installation
Languages
Languages
Menu language
Primary audio
Channel install...
Preferences
Connections assist. Secondary subtitl..
Decoder
Primary teletext
Secondary teletext
...
Hearing
g impaired
p
Rename devices
• Preferred teletext languages
Select one of the available teletext languages as
primary referred and secondary preferred
language.
• Hearing impaired
Select On to display the hearing impaired subtitle
version of your preferred audio or subtitle
language when available.
• Visually impaired (UK only)
Select to hear the additional commentary audio
(if available) in your selected audio language
through the speaker bar of your TV screen or
through the headphones or through both.
rNote:
If both Visually impaired and Hearing impaired are
enabled, the Visually impaired language will have
priority for audio, the Hearing impaired for subtitles.
• Preferred audio format
Select your preferred and available audio format
to achieve the best sound reproduction.
Select Advanced for the best sound reproduction
if a Home theatre system is connected to your
TV hub. Select Standard in all other cases.
Step 2: Select your country
Select the country where you are located.
The TV will install and arrange the TV channels
according to the country selected.
Go to a next step if your country selection is
correct.
‡ Press œ to select Channel installation.
® Press π to enter the Channel installation menu.
Automatic installation is highlighted.
Ò Press π to enter.
† Press OK.
The Country list appears.
º Press o or œ to select your country.
◊Press Next.
Visually im
impaired
m
Pref. audio format
The Languages menu also offers the following
language settings when digital channels are installed
and broadcasted.
• Preferred audio language
Select one of the available audio languages as
primary preferred and secondary preferred
language.
• Preferred subtitle languages
Select one of the available subtitle languages as
primary preferred and secondary preferred
language. See section 5.8 Subtitles.
Channel installation
Downloaded
From TV-Manual.com Manuals
Channel install...
Automatic install...
Automatic install... Start now
Installation update
Start-up message
Digital: Test recept...
Analogue: Manual...
Rearrange
25
ENGLISH
6
Step 3: Select Antenna or Cable
This selection is only available when this TV is
prepared to receive DVB-C channels in your
country.
Select Antenna to install all digital terrestrial (DVBT) and analogue channels available.
Select Cable to install all digital cable (DVB-C) and
analogue channels available.
‡ Press o or œ to select Antenna or Cable.
® Press Next.
Ò If the TV asks for it, enter the Network ID you
received from your provider.
rNote
You can do a Channel installation if you are both
connected to a digital antenna and a cable network.
Therefore do the installation twice. To watch the
stored Antenna channels or the stored Cable
channels, you will have to switch between Antenna
or Cable in the Channel installation > Antenna or
Cable menu.
Step 4: Install TV and radio channels
Your TV will search for and store all available digital
and analogue TV channels and all available digital
radio channels.
If you selected Cable in Step 3, a Settings menu is
available. Leave these settings unchanged unless
your provider supplied specific values to use for
Network frequency, Network ID or Symbol rate.
Follow the text on screen to change the settings.
Use the digit keys to enter the numbers. You can
also select to install analogue channels or not.
Step 5 Clock, time zone and daylight saving
selection
Only available when the country selected supports
digital broadcasts.
Go to a next step if this step is not applicable.
‡ Press œ to select Clock.
® Press π to enter.
Ò Press o or œ to select Auto clock mode.
† Press π to enter.
Installation
Clock
...
Auto clock mode
Connections assist. Time zone
Rename devices
Daylight saving
Audio setup
Decoder
Man. network inst.
Clock
Factory settings
Auto clock mode
Select Automatic to instruct your TV to always get
the time correctly. Time zone and Daylight saving
correction are automatically set.
Select Manual when Universal Time Coordinated
(UTC) is not available in your area.
Time zone/Daylight saving
When you selected Auto clock mode manually,
select your local time zone and choose between
Standard (winter) and Daylight saving time
(summer).
‡ Select Start.
The installation may take a few minutes.
In case of Cable selection, the TV can ask to
enter the Network ID supplied by the cable
provider. Enter this ID with the digit keys.
® When the installation is done, press Finish to
return to the Channel installation menu.
Ò Press Menu Ï to quit the menu.
à Tip
When digital channels are found, the list of installed
channels may show some empty channel numbers.
If you want to rename, reorder or uninstall stored
channels, see section 6.3 Rearrange stored
channels.
26
Downloaded
From TV-Manual.com Manuals
Channel installation
You can tune-in analogue TV channels channel by
channel manually with Manual installation.
6.2.1 Select the system
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Analogue: Manual
installation.
® Press π to enter the Manual installation menu.
System is highlighted.
Ò Press π to enter the System list.
† Press o or œ to select your country or part
of the world where you are now located.
º Press p to return to the Manual installation
menu.
Channel install...
Analogue: Manual...
Automatic install... System
Installation update Search
Start-up message
6.2.3 Fine tune a channel
Fine tune a found channel when the reception is
poor.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Analogue: manual
installation > Fine tune.
® Press π to enter the Fine tune menu.
Ò Press o or œ to adjust the frequency
† Press p when you finished fine tuning.
º Select Store current channel to store the fine
tuned channel under the current channel
number.
◊Press π to enter.
‹ Press OK.
Done appears.
≈Press Menu Ï to quit the Channel installation
menu.
Fine tune
6.3
Rearrange stored channels
To rename, reorder, uninstall or reinstall stored
channels.
Store as new ch...
Rearrange
6.3.1 Rename a channel
Assign or change a channel name to a channel for
which a name has not yet been entered.
6.2.2 Search for and store a new channel
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Analogue: manual
installation > Search.
® Press π to enter the Search menu.
Ò Press the red key to enter the frequency
yourself or press the green key to search for a
next channel.
à Tip
If you know the frequency, enter the three numbers
of the frequency with the number keys of the
remote control.
† Press p when the new channel has been
found.
º Select Store as new channel to store the new
channel under a new channel number.
◊Press π to enter.
‹ Press OK.
Done appears.
≈Press Menu Ï to quit the channel installation
menu.
Channel installation
Downloaded
From TV-Manual.com Manuals
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Rearrange.
® Press π to enter the channel list.
Ò Press o or œ in the channel list to select the
channel you want to rename.
† Press the red key.
º Press p or π to select a character or o or œ to
change the characters. Space, numbers and other
special characters are located between z and A.
◊Press the green key or OK to finish.
à Tip
To delete all characters, press the yellow key.
To delete the highlighted characters, press the blue
key.
6.3.2
Uninstall or reinstall a channel
To uninstall a stored channel so that it is no longer
possible to tune to.
Reinstall an earlier uninstalled channel.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Rearrange.
® Press π to enter the channel list.
27
ENGLISH
6.2 Analogue: Manual installation
Ò Press o or œ in the channel list to select the
channel you want to uninstall or reinstall.
† Press the green key to uninstall or reinstall the
channel.
º Press Menu Ï to quit the menu.
6.3.3 Reorder the channels
Change the order of the stored channels.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Rearrange.
® Press π to enter the channel list.
Ò Press o or œ in the channel list to select the
channel you want to reorder.
† Press the yellow key to move up the highlighted
channel in your channel list.
º Press the blue key to move down the
highlighted channel in your channel list.
◊Press Menu Ï to quit the menu.
6.4
6.5
Digital reception test
If you receive Digital TV broadcasting you can verify
the quality and signal strength of a specific channel.
‡ Select a channel.
® Press Menu.
Ò Select Setup > Installation > Channel
installation > Digital:Test reception.
† Press π to enter
º Press OK.
◊Press the green key to start the test.
Information on the quality and the signal
strength of this channel is shown.
‹ Use the cursor keys to change the frequency to
improve the signal or enter a new frequency
directly with the digit keys.
≈Press the green key to store the frequency if
the signal quality and strength are good.
Ú Press the red key to return to the Channel
installation menu.
œ Press Menu to quit the menu.
Channel management
6.4.1 Automatic search
Once a day, at 3 AM, the TV searches for all
available TV channels automatically. Leave your TV in
standby.
Earlier found channels are updated and new
channels are stored. Channels not found by the
search anymore are removed from the channel list.
When Channel management has found or removed
channels, a message at TV start up is shown. You
can activate or deactivate this message.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Startup message.
® Select On or Off.
à Tip
To achieve the best results, contact a specialised
antenna installer.
6.6
Factory settings
You might want to return to the original factory
settings. Only picture and sound settings will be
reset.
‡ Press Menu Ï and select Setup > Installation
> Factory settings.
® Press π to enter the Factory settings menu.
Ò Press OK.
† Press Menu Ï to quit the menu.
6.4.2 Manual search
You can install the updates at any time.
‡ Press Menu Ï and select Setup > Installation
> Channel installation > Installation update.
® Press π to enter the Installation update menu.
Ò Press OK.
† Press the green key to start.
The update starts and may take a few minutes.
º When the update is completed, press the red
key to return to the Channel installation menu.
◊Press Menu Ï to quit the menu.
28
Downloaded
From TV-Manual.com Manuals
Channel installation
Connections
7.1
Connection overview
Back connectors
1 Singe cable connector
2 EXT1, EXT2
Scart connectors for DVD,VCR, Digital receiver,
Game console, etc.
3a VGA-EXT3
VGA connector for a PC.
3b AUDIO L/R
Audio L/R input to be used together with the
VGA connector or the YPbPr connector.
4 Audio Out L/R
Sound output cinch connectors for a Home
Theatre System, etc.
5 YPbPr
Component video YPbPr and Audio L/R
connectors for DVD, Digital receiver or Game
console, etc.
6 Mains connector
7 HDMI 1, HDMI 2
HDMI input connectors for Blu-ray Disc player,
HD Digital receiver or HD Game console, etc.
8 Digital Audio Out
Sound output cinch connector for a Home
Theatre System, etc.
9 Antenna input
10 Service UART
For service only.
ConnectionsFrom TV-Manual.com Manuals
Downloaded
ENGLISH
7
Left side connectors
11 HDMI 3
HDMI input
12 Audio L/R
Audio L/R input to be used together with a DVI
to HDMI cable connected to an HDMI connector
(HDMI 1, 2 or 3).
13 Headphones
Stereo Mini jack
14 Audio L/R
Audio L/R input to be used together with VIDEO
on the side of the Connectivity hub.
15 VIDEO
Video input to be used together with AUDIO
L/R on the side of the Connectivity hub.
16 USB
USB connector
17 Network
Home network connector
18 Common interface
Slot for Conditional Access Modules (CAM)
29
7.2
About connections
7.2.1 What you need to know
Connect your device with the highest possible
quality connection.
Look for the highest quality connection on your
device. Use that connection to your TV hub.
HDMI - Highest quality ★★★★★
An HDMI connection has the best picture and
sound quality. One cable combines video and audio
signals. Use HDMI for HD ( High Definition) TV
signals. HDMI with EasyLink offers easy operating
of your connected devices when these have the
HDMI CEC standard. See section 7.2.2 EasyLink
A device connected with HDMI to the TV hub can
only send out audio and video signals to your TV
hub. The device cannot receive or record audio and
video from your TV.
YPbPr – Higher quality ★★★★
Use the Component Video YPbPr connections
together with Audio Left and Right. Match the cable
colours when you connect.
YPbPr can handle HD TV signals.
Component Video
YPbPr cable
- Red, Green, Blue
Audio L/R cable
- Red, White
Scart - Good quality ★★★
One cable combines video and audio signals.
Scart connectors can handle RGB video but no HD
TV signals.
HDMI cable (max. 5m)
à Tip
DVI to HDMI – Higher quality ★★★★
Use a DVI to HDMI adaptor if your device has only
a DVI connection.
Connect an Audio L/R cable to Audio In L/R (DVI
to HDMI) at the side for sound.
r Note
HDMI supports HDCP (High-bandwidth Digital
Contents Protection). HDCP is a copy protection
signal that comes with HD content (DVD disc or
Blu-ray Disc).
Scart cable
Video - Basic quality ★
Use a Video (cinch) cable together with an Audio
L/R (cinch) cable. Match the cable colours when
you connect.
Combined Video - yellow and Audio L/R cable
- red and white
30
Downloaded
From TV-Manual.com Manuals
Connections
EasyLink might not work with devices from other
brands.
One touch play
Insert a DVD disc and press Play. The TV switches
on from standby and shows the DVD programme
automatically.
System standby
Press the B key on the remote control for more
than 2 seconds to switch the connected devices in
standby.
System audio control
When you connect an audio system you can listen
to the sound from your TV through your audio
system while the TV speakers are muted. See
section 5.4.5 Sound settings,TV speakers.
7.3
Connect with the
Connection assistant
ENGLISH
7.2.2 HDMI with EasyLink
Connected devices that are compliant with the
HDMI CEC standard can work together.
‡ Press Menu Ï > Setup > Installation >
Preferences and press π to enter the list.
® Press o or œ to select EasyLink.
Ò Press π to enter.
† Press o or œ to select On or Off.
º Select On to activate EasyLink.
(if available)
Use the Connection assistant to show you how to
connect your devices to the TV hub. It sets all
necessary settings automatically.
You can also connect your devices without the use
of the Connection assistant. See section 7.4
Connect without the Connection assistant.
‡ Press Menu Ï on the remote control and
select Setup > Installation > Connection
assistant.
® Press π to start the Connection assistant.
Ò Press OK.
7.4
Connect without the
Connection assistant
The connections shown in this section are
recommendations for the most used cases. Other
solutions are possible.
When a device is connected the TV needs to know
what connection you made. See section 7.5
Connection setup.
rNote
Ensure that all HDMI-CEC features in the HDMICEC devices (for ex. Home Theatre System) are
properly set up.
7.2.3 Display synchronised audio out
For the best match of image and sound in speech
on screen, connect a Home Theatre System to
Audio Out L/R or Digital Audio outputs. See
diagrams 7.4.4 and 7.4.8.
Never connect the audio signal of a DVD player,
digital receiver or other audio/video device directly
to the Home Theatre System.
ConnectionsFrom TV-Manual.com Manuals
Downloaded
31
7.4.1 DVD player
Use a scart cable to connect the device to the
EXT1 input at the back of the TV hub.
7.4.2 DVD Recorder or Digital Receiver
Use a scart cable and 2 antenna cables.
7.4.3 DVD Recorder and Digital Receiver
Use 3 scart cables and 3 antenna cables.
32
Downloaded
From TV-Manual.com Manuals
Connections
DVD Recorder and Home Theatre
System
Use a scart cable, 2 antenna cables and 1 digital
audio (cinch) cable.
ENGLISH
7.4.4
7.4.5
DVD Recorder and DVD Home
Theatre System
Use 2 scart cables, 2 antenna cables and 1 digital
audio (cinch) cable.
7.4.6 Satellite receiver
Use a scart cable and 2 antenna cables.
ConnectionsFrom TV-Manual.com Manuals
Downloaded
33
7.4.7
HD Digital receiver / HD satellite
receiver
Use an HDMI cable and 2 antenna cables.
7.4.8
DVD-R, Home Theatre System and
Digital receiver
Use 3 scart cables, 3 antenna cables and 1 audio
(cinch) cable.
7.4.9 Blu-ray Disc player
Use an HDMI cable.
34
Downloaded
From TV-Manual.com Manuals
Connections
7.4.11 Camcorder
The most practical connection for a camcorder is at
the side of the TV hub.
rNote:
To prevent picture delay, set the TV in game mode.
Press Menu > TV menu > Smart settings > Game.
Connected at the side of the TV hub
Use the HDMI connection or the Video and Audio
L/R connections.
Connected at the side of the TV hub
Use the HDMI connection or the Video and Audio
L/R connections.
Connected at the back of the TV hub
Use an HDMI connection or the EXT3-YPbPr and
Audio L/R connections for HD quality.
Connected at the back of the TV hub
Use an HDMI connection or the EXT3-YPbPr and
Audio L/R connections for HD quality
ConnectionsFrom TV-Manual.com Manuals
Downloaded
35
ENGLISH
7.4.10 Game console
The most practical connections for a game console
are at the side of the TV hub.
7.4.12 Personal Computer
You can connect your PC directly to the TV hub.
The Essence Full HD screen works as a monitor of
your PC.
For more features you can connect your PC in a
PC network. See section 7.7 PC network.
As a monitor the PC can be connected with a DVI
to HDMI adaptor. Alternatively you can connect
the PC with the VGA connection.
VGA connection
Use a VGA cable to connect the PC to the EXT3
connection at the back of the TV hub.
Connect the Audio L/R to the EXT3 Audio L/R.
ç Caution
Before connecting the PC, set the PC monitor
refresh rate to 60Hz.
à Tip
Set the TV picture format to Unscaled in the
Picture format menu for maximal PC picture
sharpness. See section 5.3.4 Widescreen picture
format.
DVI to HDMI connection
Use a DVI to HDMI adaptor to connect to the
HDMI side
For supported PC monitor resolutions, see section
8 Technical data.
7.5
Connection setup
The TV needs to know what connections you have
made and which device is connected to which
connector.
If you have used the Connection assistant the
connection setup is already done.
or back connection.
7.5.1 Naming your devices
Name the connected devices for easy selection and
best signal handling.
Assign the type of device (DVD, VCR, Game, ...) to
the connector you use for that device.
‡ Press Menu Ï on the remote control and
select Setup > Installation> Rename devices.
® Press π to enter the list.
Ò Press o or œ to select the connector you
used for the device you connected.
† Press π.
º Press o or œ to select the type of device.
◊Press Menu Ï to quit the menu.
Connect the Audio L/R for sound.
36
Downloaded
From TV-Manual.com Manuals
Connections
Installation
Decoder
...
Preferences
Channel
Status
It can take a few minutes before a CAM is
activated. Removing the CAM will deactivate the
digital TV service.
ENGLISH
7.5.2 Decoder channels
Decoders that decode an antenna channel are
connected to EXT1 or EXT2 (scart).
You have to assign the TV channel as a channel to
be decoded. Then assign the connection where the
decoder is connected.
‡ Press Menu Ï on the remote control and
select Setup > Installation > Decoder >
Channel.
® Press π to enter the list.
Ò Press o or œ to select the channel to decode.
† Press p and go back to select Status.
º Press o or œ to select the connector used by
the decoder.
◊Press Menu Ï to quit the menu.
Connections assist.
Rename devices
Decoder
Man. network inst.
Clock
Factory settings
7.6
Preparing for digital
services
Scrambled digital TV channels can be decoded with
a Conditional Access Module (CAM) and a Smart
card provided by a digital TV service operator. The
CAM may enable several services depending on the
operator you choose (e.g. Pay TV).
Contact your digital TV service operator for more
information and terms.
7.6.1
7.6.2 Common interface menu
From this menu you access the CAM service you
have installed. The applications and their function,
the content and the messages on screen come
from the CAM service provider.
‡ Press Menu Ï on the remote control and
select Features > Common interface.
This menu option is available when a CAM is
inserted and has made contact with the provider.
Insert a Conditional Access Module CAM
) Warning
Switch off the TV hub before inserting the CAM.
Look on the CAM for the correct inserting
direction. Incorrect insertion can damage the CAM
and the TV.
‡ Gently insert the CAM into the Common
Interface slot at the side of your TV hub as far
as it will go.
® Leave the CAM in the Common Interface slot
permanently.
ConnectionsFrom TV-Manual.com Manuals
Downloaded
37
7.7
PC network
You can link up your TV on a PC network in your
home. Watch your photos and listen to your music
from any linked PC on the TV. The PC network
feature of this TV is DLNA certified.
You can use Microsoft Windows XP or Vista, Intel
Mac OSX or Linux.
An example of a home PC network.
† Some media server software needs a setting to
share your files with the TV.
In the media server this TV will present itself as
a number - a MAC or IP number.
Have the TV and router switched on for this
number to appear in the media server.
Select the TV number in the media server and
set the server to share files with this number.
For media server software marked with an * in
section 8 Technical data, a step by step setting
instruction is available. See section 7.7.4 Media
server settings.
A firewall, a security system on your computer,
could also block the network connection.
Allow the media server software to go to the
network.
Hub
7.7.1
What you need
To set up your TV in a home PC network you
need:
• a router and a computer in a home network
• a network cable
• recent media server software (Windows, media
Player 11 or similar) on your computer.
For a complete list of compatible media server
software see section 8 Technical data.
7.7.2
Set up a PC network connection
On the TV no special settings are necessary to
connect automatically to the network.
‡ Connect the network cable from your router to
the Network
connector at the side of the
TV hub.
º Press the Source v key on the remote
control.
◊Select PC network and press π.
It could take some time for the TV to connect.
‹Use the colour and navigation/rotation keys to
browse your folders or play your files.
If the TV cannot connect to the network, study the
server software, router or PC manuals.
7.7.3 Manual network setup
Some expert network settings can be set on the
TV. The DHCP is set to On to automatically
connect to the network.
Press Menu Ï > Setup > Installation > Manual
network installation.
® Switch on the router. Set the router to DHCP
On.
Ò Switch on the computer and start the media
server software.
38
Downloaded
From TV-Manual.com Manuals
Connections
Media servers need to be set for sharing their files
and folders. Follow the instructions closely to set
your specific server.
Windows Media Player v11on Windows Vista
Set for network sharing
Set Network discovery to On. Set File sharing to
On. Go back to the Media Sharing window in
Windows Media Player and check the Share my
media box. Click OK.
ENGLISH
7.7.4 Media server settings
When the TV is connected, by the router, to the
PC and everything is switched On, the Media
sharing window will show the TV as an Unkown
Device. Select the device and click Allow.
In Windows Media Player select Library from the
menu and select Media sharing.
1
2
In the Media Sharing window, check the Share my
media box. Click OK.
You can open the Settings window to change
particular settings on sharing.
When the device icon (the TV) is checked with a
green tick, click OK.
Set folders for sharing
In Windows Media Player select Library from the
menu and select Add to Library.
1
2
If no network connection was found, and you are
unable to check this box, click the Networking
button to show the Network and Sharing Center
window, …
In the Add To Library window, select My folders
and those of others that I can access and click
the Advanced Options button. …
1
2
ConnectionsFrom TV-Manual.com Manuals
Downloaded
39
1
2
With Advanced Options open, you can add
specific folders to the list to share. Click Add.
1
Now everything is set to enjoy music, photos and
videos on your TV.
In the Add Folder window select a folder with
music, photos or videos you want to share with
other devices (your TV). Click OK.
Windows Media Player v11 on Windows XP
Set for network sharing
In Windows Media Player select Library from the
menu and select Media sharing …
1
2
In the Add To Library window the newly added
folder is shown. You can add more folders to
share. Click the OK button to add the files to the
library.
40
Downloaded
From TV-Manual.com Manuals
Connections
With Advanced Options open, you can add
specific folders to the list to share. Click Add.
ENGLISH
In the Media Sharing window, check the Share my
media box.
When the TV is connected, by the router, to the
PC and everything is switched On, the Media
sharing window will show the TV as an Unkown
Device. Select the device and click Allow.
1
1
2
3
You can open the Settings window to change
particular settings on sharing.
When the device icon (the TV) is checked with a
green tick, click OK.
In the Add Folder window select a folder with
music, photos or videos you want to share with
other devices (your TV). Click OK.
Set folders for sharing
In Windows Media Player select Library from the
menu and select Add to Library.
In the Add To Library window the newly added
folder is shown. You can add more folders to
share. Click the OK button to add the files to the
library.
In the Add To Library window, select My folders
and those of others that I can access and click
the Advanced Options button.
ConnectionsFrom TV-Manual.com Manuals
Downloaded
41
Click the Sharing tab.
1
Set folders for sharing
Click the green plus icon and select Add folder…
1
2
Now everything is set to enjoy music, photos and
videos on your TV.
TVersity v.0.9.10.3 on Windows XP
In the Add media pop-up window, click the
Browse button.
Set for network sharing
Click the Settings tab and click the Start Sharing
button.
1
2
1
In the Browse for Folder window select a folder
with music, photos or videos you want to share.
Click OK.
A pop-up window tells you that the media
server service is started. Click OK.
42
Downloaded
From TV-Manual.com Manuals
Now everything is set to enjoy music, photos and
videos on your TV.
Connections
Set for network sharing
In the blue frame click the hard disk name to
browse to a folder with music, photos or videos
you want to share with other devices (your TV).
ENGLISH
Twonky Media v4.4.2 on Macintosh OS X
In Twonky Media click Basic Setup > First steps.
In this window you can change the server name
that appears on your TV.
1
2
Click Select to select the folder for sharing.
Now click Save Changes.
Click Basic Setup > Clients/Security.
Check the box next to Enable sharing for new
clients automatically.
Then click Rescan content directories.
In some cases this might not make all files and
folders available.
Set folders for sharing
Click Support > Troubleshooting and click
Rebuild database to make sure everything
works OK. This rebuilt might take a while.
Click on Basic Setup > Sharing.
Some ‘Content Locations’ might be set already
automatically. To add a folder (a content location)
to be shared on the network click the Browse
button.
Now everything is set to enjoy music, photos and
videos on your TV.
1
2
ConnectionsFrom TV-Manual.com Manuals
Downloaded
43
8
Technical data
Picture / Display
• Display type: LCD Full HD W-UXGA
• Panel resolution: 1920x1080p
• Perfect Pixel HD picture enhancement
• 1080p 24/25/30/50/60Hz processing
• 100 Hz Clear LCD
Supported display resolutions
• Computer formats
Resolution
Refresh rate
640 x 480p
60Hz (VGA/HDMI)
600 x 800p
60Hz (VGA/HDMI)
1024 x 768p
60Hz (VGA/HDMI)
1280 x 768p
60Hz (VGA/HDMI)
1360 x 765p
60Hz (VGA/HDMI)
1360 x 768p
60Hz (VGA/HDMI)
1280 x 1024p
60Hz (HDMI)
1920 x 1080i
60Hz (HDMI)
1920 x1080p
60Hz (HDMI)
• Video formats
Resolution
Refresh rate
480i
60Hz
480p
60Hz
576i
50Hz
576p
50Hz
720p
50Hz, 60Hz
1080i
50Hz, 60Hz
1080p
24Hz, 25Hz, 30Hz
1080p
50Hz, 60Hz
Tuner / Reception / Transmission
• Antenna input: 75ohm coaxial (IEC75)
• TV system: DVD COFDM 2K/8K,
(MPEG2, MPEG4 if available)
• Video playback: NTSC, SECAM, PAL
• DVB: DVB Terrestrial/DVB cable
(see selected countries on the TV typeplate)
Sound
• Sound system:
- Virtual Dolby Digital
- BBE
Multimedia
• Connections: USB
• Playback formats: MP3, Slideshow (.alb)
JPEG, MPEG1, MPEG2.
44
Downloaded
From TV-Manual.com Manuals
Supported media server software
• Windows Media Player 11 (on Microsoft
Windows XP* or Vista*)
• PacketVideo Twonky Media 4.4.2 (on PC* &
Intel Mac OSX*)
• Sony Vaio media server (on Microsoft Windows
XP or Vista)
• TVersity v.0.9.10.3 (on Windows XP*)
• Nero 8 - Nero MediaHome (on Microsoft
Windows XP)
• DiXiM (on Windows XP)
• Macrovision Network Media Server (on
Windows XP)
• Fuppes (on Linux)
• UShare (on Linix)
• Philips Media Manager (on Microsoft Windows
XP)
• Philips NAS SPD8020
* For this media server software a step by step
setting instruction is available in the online User
manual on www.philips.com/support.
Supported USB/Memory device formats
• FAT 16, FAT 32, NTFS.
Remote control
• Type: RC4480
• Batteries: 2 coin cell batteries CR2032
Connectivity
Back
• EXT1 (scart): Audio L/R, CVBS in, RGB
• EXT2 (scart): Audio L/R, CVBS in, RGB,
• EXT3: Y Pb Pr or VGA, Audio L/R
• HDMI 1 in (HDMI 1.3a for all HDMI
connections)
• HDMI 2 in
• Audio Out L/R - display synchronised
• Digital Audio out (coaxial-cinch-S/PDIF) display synchronised
Side
• HDMI 3 side in
• Audio In L/R (DVI to HDMI)
• Audio In L/R
• Video in (CVBS)
• Audio L/R in
• Headphone (stereo mini jack)
• USB
• Common interface slot
• Network - (RJ45)
Technical data
ENGLISH
Power
• Mains power: AC 220-240V (±10%)
• Power and standby power consumption:
See technical specification on www.philips.com
• Ambient temperature: 5°C - 35°C
Specifications are subject to change without notice.
For more specification details of this product see
www.philips.com/support.
Dimensions and weights (approx.)
TV screen
42PES0001D/H
-
982 mm
632,5 mm
49,8 mm
± 16,5 kg
width
height
depth
weight
TV screen + stand
- width
982 mm
- height
685 mm
- depth
250 mm
- weight
± 20 kg
Connect. hub
- width
320 mm
- height
84 mm
- depth
320 mm
- weight
± 4,7 kg
Technical data
Downloaded
From TV-Manual.com Manuals
45
9
Troubleshooting
Television and remote control
Picture
The TV does not switch on
• Verify the mains cord connection.
• Verify if both connectors of the single cable are
connected properly to the TV hub and to the TV
screen.
• Verify if you pulled out the plastic insulation sheet
from the batteries of the remote control.
• Verify if the batteries of the remote control are not
empty or weak.Verify their orientation.You can use
the keys on the TV hub to switch the TV on.
• Unplug the mains cord, wait a minute and plug it
back in.Try again to switch on.
The sound is on, but there is no picture
• Verify the contrast or brightness setting in the menu.
The TV does not react on the remote control
• Verify if the batteries of the remote control are not
empty or weak.Verify their + orientation.
• Clean the remote control and TV sensor lens.
The TV switches off and the red light blinks
• Unplug the mains cord, wait a minute and plug it
back in.Verify if there is enough space for ventilation.
Wait until the Connectivity hub has cooled down.
When the TV does not restart to standby and the
blinking occurs again, call our Customer Care.
You forgot your code to unlock Child lock
• See section 5.7.3 Set code / Change code.
Wrong language in the TV menu ?
Follow these steps to change the language.
‡ Press Menu Ï on the remote control.
® Use œ to select the last menu line.
Ò Press πthree times.
† Press o or œ to select your language.
º Press OK.
◊Press Menu Ï to quit the menus.
TV channels
Some TV channels are gone
• Verify if the correct channel list is chosen.
• A channel could be uninstalled in the Rearrange
menu.
No digital channels found during installation
• Verify if the TV supports DVB-T or DVB-C in your
country. See the label “Digital TV Country
Compatibility” on the back of the TV screen.
46
Downloaded
From TV-Manual.com Manuals
The TV picture is poor
• Verify if the antenna is connected properly.
• Non-earthed audio devices, neon lights, high
buildings or mountains can influence the picture
quality.Try to improve the picture by changing the
antenna direction or place devices away from the
TV.
• Verify if the correct TV system is chosen in the
Manual installation menu.
• If only a certain channel is poor, try to fine tune this
channel in the Fine tune menu. See section 6.2.3.
The picture has poor colour
• Verify the colour settings in the Picture menu.
Select any of the smart settings in the Smart
settings menu. See section 5.3.1.
• Verify the connections and cables of the connected
devices.
Picture delay when a game console is connected
• To prevent picture delay, set the TV in game mode.
Press Menu > TV menu > Smart settings > Game.
The TV does not remember my settings when I
switch back on
• Verify if the TV is set to Home in the TV menu >
Setup > Installation > Preferences > Location
menu.
The picture does not fit the screen, it is too big or
too small
• Select a more fitting picture format in the Picture
format menu.
See section 5.3.4 Widescreen picture format.
• Name your connected device in the Connections
menu to obtain the best signal handling.
See section 7.5.1 Naming your devices.
The picture position on screen is not correct
• Some picture signals from some devices do not fit
the screen correctly.You can shift the picture with
the cursor keys on the remote control.Verify the
signal output of the device.
Troubleshooting
USB connection
There is a picture but no sound
• Verify the volume is not set to 0.
• Verify the sound has not been muted with the ¬
key.
• Verify if all cables are connected properly.
• If no sound signal is detected, the TV automatically
switches off the sound.
This is proper operation and is not a malfunction.
The TV does not show the USB device content
• Set your device (camera) to ‘Mass Storage Class’
compliant.
• The USB device may need specific driver software.
Unfortunately this software cannot be downloaded
to your TV.
I cannot see my files in the Multimedia menu.
• Not all audio and picture files are supported. See
section 8 Technical data.
The sound is poor
• Verify if the sound is set to Stereo.
• Verify the Equalizer in the Sound menu.
• Select any of the Smart settings in the menu.
Sound delay when A HTS-DVD device is connected
• See the user manual of the HTS-DVD device to
adjust the audio sync delay.
If you cannot set A delay, switch off HD Natural
Motion in the Picture > Perfect Pixel HD menu. See
section 5.3.3 Picture settings.
HDMI connections
Trouble with devices connected with HDMI
• The HDMI - HDCP procedure might take a few
seconds before the TV shows the picture from a
device.
• If the TV does not recognise the device and the
screen shows no picture, try switching from one
device to another and back again to restart the
HDCP procedure.
• If sound interruptions occur persistently, see the user
manual of the device to verify the output settings. If
that does not help, connect an additional audio
cable.
• If a DVI to HDMI adaptor is used, verify if an
additional audio connection is in place to complete
the DVI connection.
• HDMI with EasyLink does not work
- Verify if the connected device supports the HDMI
CEC standard. See the user manual that comes
with the device.
- Verify if the HDMI cable is properly connected.
- Verify if Easylink is activated in the Setup,
Installation, Preferences menu.
- Ensure that your HDMI CEC audio devices are
properly set up. See the user manual that comes
with your audio device.
Troubleshooting
Downloaded
From TV-Manual.com Manuals
Photo and music files do not playback smoothly
• The transfer performance of the USB device limits
the transfer rate.
Personal computer
The PC display on my TV is not stable or is not
synchronised
• Verify if the correct resolution mode is selected on
your PC. See section 8 Technical data.
I cannot find my PC files on my PC
• Verify if files have been added in the folder.
• Not all file formats are supported. See section 8
Technical data.
PC files are not shown in the PC network menu
• You have to set the PC media server to share files
with the TV. See section 7.7.2 Set up a PC network
connection.
PC files do not play
• See section 8 Technical data for supported file
formats.
Unplug the network cable
To unplug the network cable from the TV hub, use
a pen or screwdriver to push down the security
clip.
47
ENGLISH
Sound
If your problem is not solved
Switch your TV off and on again, that may help. If not,
call our Consumer Care or consult our website
www.philips.com/support.
Find the Consumer Care telephone numbers on the
back cover of this manual.
Please, have the TV Model and Product Number
ready before you call.
You can find these numbers on the packaging label or
on the typelabel on the back and bottom of the TV
hub.
) Warning
Never try to repair the TV yourself.
48
Downloaded
From TV-Manual.com Manuals
Index
100 Hz Clear LCD 13
A
Active control 13
Advanced sharpness 13
Analogue
manual installation 27
TV channels 27
Antenna
cable 7
connect 7
with devices 29
Auto clock mode 26
Auto format 14
Automatic installation 25
Auto surround 15
Auto Volume levelling 15
B
Balance
sound 15
Batteries 3,7
Blacklevel 13
Blu-ray Disc 34
Brightness 13
C
CA module 37
Cable
HDMI 30
Scart 30
Video 30
YPbPr 30
Camcorder 35
Camera (photo) 35
Care of the screen 3
Change code 19
Channel
all channels list 17
favourite list 17
installation 25
lock 19
management 28
up/down 11
previous 10
rearrange 27
store / install 27
Child lock 19
ENGLISH
10 Index
Clock 26
Code 19
Colour
enhancement 13
menu 13
keys 4,10
Common interface (CAM)
menu 37
slot 29,37
Connection
assistant, 31
best 30
overview 29
set up 37
Connectivity hub 5
Contrast 13
Country selection 25
Custom lock 19
Custom tint 13
D
Daylight saving 26
Decoder channel 37
Delta volume 15
Device
connecting 31
naming 37
watch 9
DHCP 38
Digital
audio out 29
subtitle language 20
receiver 32
text services 16
test reception 28
Dual I/II 15
Dual screen 11
DVB-C 5
DVB-T 5
DVD
connect 32
playback 9
player 32
recorder 32,33
Dynamic
backlight 13
contrast 13
Index
Downloaded
From TV-Manual.com Manuals
E
EasyLink 31
Electronic Programme Guide 18
Energy saving 12
Equalizer 14
External 1,2,3 (EXT) 29
F
Factory settings 28
Favourite channel lists 17
Fine tune 27
G
Game console 35
H
HDCP 30
HDMI connection 30
HD digital receiver 34
HD natural motion 13
Headphone
connect 4,29
volume 15
Hearing impaired 25
Home theatre system 33
Hue 13
I
Installation
automatic 25
manual 27
manual network setup 38
menu 25
update 28
K
Kensington Security Slot 5
Key(s)
colour 10
on TV 4
on remote control 4,10
L
Language
menu 25
audio 15
subtitle 20
Location 46
Locks 19
49
M
Menu key 11
Mono 15
Movie expand 14
MPEG artefact reduction 13
Music 20
Mute key 10
N
Naming devices 37
Network setup 38
unplug the network cable 47
Noise reduction 13
O
OK key 10
On timer 19
Settings assistant 12
Sharpness 13
Sleeptimer 19
Smart settings 12
Software update 23
Sound
menu 14
surround mode 15
Speaker bar 6
Standby 10,19
Stationary images 3
Stereo 15
Subtitle 20
language 20
shift 14
Super zoom 14
Surround mode 15
Switch on 8
visual impaired 15
W
Whitepoint 13
Widescreen picture format 14
Y
YPbPr 30
P
PC network 38
Perfect Pixel HD 13
Personal Computer
connect 36
display resolutions 44
Photo viewer 21
Picture
album 21
delay 35
format 13
menu 13
Position the TV screen 5
Power cable 7
Preferred audio format 25
R
Radio channel 22
Rearrange channels 27
Recorder 32
Recycling 3
Remote control
batteries 7
overview 10
Rename 27
Reorder 28
T
Table of Pages T.O.P 15
Technical data 44
Teletext 15
digital 16
dual screen 16
language 15
menu 16
page 16
teletext 2.5 16
Time zone 26
Timers 19
Tint 13
Troubleshooting 46
TV screen 5
TV speakers 15
U
Unmount the stand 6
Unscaled 14
USB
connector 29
device 20
photo viewer 20
V
S
Safety 3
Satellite receiver 33
Scart connection 30
Screen cleaning 3
Search
channels 27
teletext pages 15
Set code 19
VCR
connect 32
VGA 36
Video cable 30
Video formats 44
Visual impaired 15,25
Volume
bar 14
key 10
50
Downloaded
From TV-Manual.com Manuals
Index
ENGLISH
Information about how to
re-tune your TV during the
digital TV switchover.
Keep this user manual safe
- you'll need it.
.........................................
Television in the UK is going digital, bringing us all
more choice and new services. Starting in late 2007
and ending in 2012, television services in the UK
will go completely digital, TV region by TV region.
Please see the next page to find out when your area
switches to digital.
Digital UK is the independent, non-profit organisation leading the process of digital TV switchover in
the UK. Digital UK provides impartial information on
what people need to do to prepare for the move to
digital, and when they need to do it.
Downloaded From TV-Manual.com Manuals
How the switch over affects your
TV equipment :
Your new TV has a digital tuner built in, which
means it is ready to receive the Freeview signal by
simply plugging it into your aerial socket (check if
you can get digital TV through your aerial now, or
whether you'll have to wait until switchover, at
www.digitaluk.co.uk).
When the TV switchover happens in your area, there
are at least two occasions when you will need to
re-tuner your TV in order to continue receiving your
existing TV channels, and also to pick up new ones.
51
Digital UK, the body leading the digital TV switchover, will advise you when you need to re-tuner
during the switchover.
If you choose to connect your TV to satellite or
cable with a digital box then it will no be affected
by switchover, and you won't need to re-tune.
If you have any questions, please contact your
equipment supplier or call Digital UK on ...
0845 6 50 50 50 or visit www.digitaluk.co.uk
How to re-tune:
To find out how to re-tune your TV, check this user
manual for details.
Go to section 6.1 Automatic installation and go to
Step 4 Install TV and radio channels.
If you do not re-tune your channels when advised to
do so by Digital UK, you may lose some or all of`
your channels until you do re-tune. You should
re-tune your TV every few months to check for any
new channels.
If you are missing any channels, it may be that they
are not available in your area, or that your aerial
needs upgrading.
When does switchover happen?
* Copeland switches on October 17, 2007
The exact date you switch
depends on the transmitter
you are served by. To check
when you switch, go to
Digital UK's postcode
checker on
www.digitaluk.co.uk.
Check your ITV news service
or look at Teletext page 106
to see what TV region you're
in.
Visit us at digitaluk.co.uk
Call us on 0845 6 50 50 50*
* Calls charged at BT rate of 3p pr minute daytime and
1p per minute evenings and weekends. Rates may vary
for calls from non-BT lines.
52
Downloaded
From TV-Manual.com Manuals
Downloaded From TV-Manual.com Manuals
Contact information
Type no.
Product no.
België / Belgique
078 250 145
€0.06/min
Italia
8403 20086
€0.08/min
Svenska
08 5792 9100
Local
Danmark
3525 8759
Local
Luxembourg
40 6661 5644
Locale
Suomi
09 2311 3415
Local
Deutschland
01803 386 852
€0.09/min
Nederland
0900 8407
€0.10/min
United Kingdom
0870 900 9070
France
0821 611 655
€0.09/min
Norge
2270 8111
Local
E§§A™
0 0800 3122 1280 ¢ˆÚ¿Ó
Österreich
0810 000205
€0.07/min
España
902 888 784
€0.10/min
Portugal
2 1359 1442
Ireland
01 601 1777
Local
Schweiz / Suisse / Svizzera
0844 800 544
Local
Local
Local
Printed in Belgium
Downloaded From TV-Manual.com Manuals