Marquis 10DD Operating instructions

Installation Instructions
Model Numbers:
Certified to:
Model Numbers:
Certified to:
ZCV39N, ZCV39NE, ZCV39LP, ZCV39LPE
ZCV42N, ZCV42NE, ZCV42LP, ZCV42LPE
ANSI Z21.50-2012, CSA 2.22-2012, CGA 2.17-M91
ZERO CLEARANCE VENTED GAS FIREPLACE
BENTLEY
ZCV39NH, ZCV39NHE, ZCV39LPH, ZCV39LPHE
ZCV42NH, ZCV42NHE, ZCV42LPH, ZCV42LPHE
ANSI Z21.88a-2012, CSA 2.33a-2012, CGA 2.17-M91
ZERO CLEARANCE VENTED GAS FIREPLACE HEATER
This appliance may be installed in an aftermarket, permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified kit is used.
WARNING: If the information in these instructions are not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
-Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
-WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department
-Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
⚠WARNING
HOT GLASS WILL
CAUSE BURNS
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed.
For Propane Horizontal
installations the venting must
be an additional one foot
above the minimum vertical
rise off the flue before going
horizontal.
A Division of R-Co. Inc.
2340 Logan Ave.
Winnipeg, Manitoba Canada
R2R 2V3 Ph.: (204) 632-1962
Printed in Canada March 3, 2014
Part# 39ZCV-MAN
Table of Contents
INFORMATION
Table of Contents……………………………………………………………................................................................
Glass Safety / Termination Cap Safety- All Units………………………………………………………………………..
Warnings, Installations, and Operations…………………………………..................................................................
Pre-installation Questions and Answers…………………………………..................................................................
Operating Instructions………………………………………………………................................................................
Recommendations for Finishing of Clean View Installations.................................................................................
Mobile Home/Manufactured Housing Installation……………………......................................................................
Nailing Tab Guide...................................................................................................................................................
ZCV39 / ZCV42 Framing Your Gas Fireplace…………………………………………………………………………...
2-3
4
5-6
7
7
8
9
10
11
ZCV39 INSTALLATION
Locating Your Appliance / Fireplace Dimensions………………………………………………………………………..
Framing Dimensions………………………………………………………………………………………………………..
Facing Requirements……………………………………………………………………………………………………….
Facing Material Dimension Requirements……………………………………………………………………………….
ZCV-TLK Optional Tile Lip Kit …………………………………………………………………………..........................
Mantel Clearances………………………………………………………………………………………………………….
Clearance to Combustibles………………………………………………………………………………………………..
12
13
14
15-17
17
18
19
ZCV42 INSTALLATION
Locating Your Appliance / Fireplace Dimensions………………………………………………………………………..
Framing Dimensions………………………………………………………………………………………………………..
Facing Requirements……………………………………………………………………………………………………….
Facing Material Dimension Requirements……………………………………………………………………………….
ZCV-TLK Optional Tile Lip Kit …………………………………………………………………………..........................
Mantel Clearances……………………………………………………………………………………………………….....
Clearance to Combustibles………………………………………………………………………………………………...
ACCESSORIES
ZCV39CSS / ZCV42CSS Child Safety Screen Installation………………………………………………………….....
ZCV39 / ZCV42 Surround Installations…………………………………………………………………………………...
MQZCV39DD / MQZCV42DD Designer Door Installations…………………………………………………………….
ZCV39 / ZCV42 51UHS Box / Component Locations…………………………………………………………………..
ZCV39 / ZCV42 Z46FK Fan Kit Installation………………………………………………………………………………
Fan Speed Control Outside of Fireplace…………………………………………………………………………………
ZCV39PL / ZCV42PL Porcelain Liner Installation……………………………………………………………………….
ZCV39RL / ZCV42RL Brick Liner Installation……………………………………………………………………………
ZCV39GT / ZCV42GT Glass Tray Setup…………………………………………………………………………………
ULK2 Universal Light Kit……………………………………………………………………………………………………
Log F3 Setup………………………………………………………………………………………………………………...
RBCB1 Cannonballs………………………………………………………………………………………………………..
MQ Dealer Accessories for ZCV39 / ZCV42……………………………………………………………………………..
MQ Log F9 Setup…………………………………………………………………………………………………………...
GENERAL INSTALLATION, USE, AND MAINTENANCE
Door and Glass Information………………………………………………………………………………………………..
Gas Line Installation………………………………………………………………………………………………………..
Millivolt System, Lighting, and Burner Control…………………………………………………………………………...
Troubleshooting the Gas Control System………………………………………………………………………………..
Burner System Maintenance………………………………………………………………………………………………
Conversion Kit Instructions – PART A……………………………………………………………………………………
Gas Conversion Kit For Top Convertible Pilot PART B…………………………………………………………………
20
21
22
23-25
25
26
27
28
29
30
31
32
33
34
35
36
37-38
39
40
41-43
44-45
46
47
48
49
50
50-51
52
2
Gas Conversion for Modulator – PART C………………………………………………………………………………..
Burner Removal / Burner System Removal / Installation……………………………………………………………….
IPI SECTION
IPI Electronic Ignition System……………………………………………………………………………………………...
Remote Control Operation…………………………………………………………………………………………………
IPI Electronic Ignition Parts List – Standard System……………………………………………………………………
Configuration 1: Basic Manual Hi / Lo and manual Off…………………………………………………………………
Configuration 2: Remote On / Off and manual Hi / Lo…………………………………………………………………..
Operating the Receiver Without Batteries For GT / EGT / GTM / EGTM Remote Controls………………………..
Configuration 3: Remote ON/OFF, Variable HI/LO, and Fan…………………………………………………………..
Electronic Ignition Lighting Instructions…………………………………………………………………………………..
VENTING
Vent Termination……………………………………………………………………………………………………………
General Vent Installation…………………………………………………………………………………………………...
Installation of Side Wall Venting…………………………………………………………………………………………..
Venting Routes And Components…………………………………………………………………………………………
Horizontal Venting Table…………………………………………………………………………………………………...
Z47ST24 / Z47ST36 Horizontal Snorkel Terminations………………………………………………………………….
Venting Straight Up Through Roof………………………………………………………………………………………..
58PVH POWER VENT
58PVH Dimensions…………………………………………………………………………………………………………
Installation Overview………………………………………………………………………………………………………..
PVH58 Termination Installation……………………………………………………………………………………………
PVH58 Venting Clearances………………………………………………………………………………………………..
PVH58 Venting- Hard Pipe Or Flex…………………………………………………………………………………….....
PVH58 Venting Configurations…………………………………………………………………………………………….
PVH58 Wall Thimble Installation…………………………………………………………………………………………..
Power Vent Mounting……………………………………………………………………………………………………….
PVH58 Wiring Harness Connections……………………………………………………………………………………..
PVH58 Millivolt System Connections……………………………………………………………………………………..
PVCM Schematic – Millivolt………………………………………………………………………………………………..
PVH58 IPI System Connections…………………………………………………………………………………………..
PVH58 Basic IPI System Connections……………………………………………………………………………………
PVH58 All IPI System Connections……………………………………………………………………………………….
PVCM Schematic – IPI……………………………………………………………………………………………………..
PVH58 Air Intake Adjustment……………………………………………………………………………………………...
PVH58 Troubleshooting……………………………………………………………………………………………………
PARTS LISTS
PVH58 Parts List……………………………………………………………………………………………………………
ZCV39 Parts List…………………………………………………………………………………………………………….
ZCV42 Parts List…………………………………………………………………………………………………………….
WARRANTY
Limited Lifetime Warranty……………………………………………………………………………………………….....
53
54
55
56
57
58
59
60
61
62
63
64
64
65
65
66
67-68
69
70
70
71
72-73
74
75
75
76
77-78
79
80
81
82
83-84
85
86
87
88-89
90-91
92
3
-Glass Safety- All Units
IT IS THE
RESPONSIBILITY
OF THE HOME
OWNER TO ENSURE
THAT NO ONE
TOUCHES A HOT
APPLIANCE.
If the barrier becomes
damaged, the barrier shall
be replaced with the
manufacturer’s barrier for
this appliance.
Any safety screen, guard,
or barrier removed for
servicing the appliance,
must be replaced prior to
operating the appliance.
 Children and adults should be alerted to the hazards of the high surface temperatures of this appliance and
should stay away to avoid burns or ignition of clothing.
 Do not clean when the glass is hot.
 Young children should be carefully supervised when they are in the same room as the appliance. Toddlers,
young children and others may be susceptible to accidental contact burns.
 A physical barrier is recommended if there are at risk individuals in the house. To restrict access to a fireplace or
stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.
 Do not leave the fireplace remote control where it is accessible to children.
-Termination Cap Safety- All Units
WARNING:
WHEN THE HORIZONTAL VENT TERMINATION IS ACCESSIBLE
A CERTIFIED GUARD (SAFETY CAGE) SHALL BE INSTALLED.
SAFETY CAGES ARE AVAILABLE FOR ALL HORIZONTAL VENT TERMINATIONS.
CHECK WITH YOUR DEALER.
 TERMINATION CAP IS HOT! Do not place flammable materials on or within 24 inches of termination caps.
 It is imperative that the vent termination be located observing the minimum clearances as shown in manual.
 There must not be any obstruction such as bushes, garden sheds, fences, decks or utility buildings within 24"
from the front of the termination plate.
 Do not locate termination where excessive snow or ice build-up may occur. Be sure to check vent termination
area after snow falls and clear to prevent accidental blockage of venting system. When using snow blowers,
make sure snow is not directed towards vent termination area.
 Venting terminal shall not be recessed into a wall or siding.
4
Warnings, Installations and Operations
Installation Regulations
This gas appliance must be installed by a qualified installer in accordance with local building codes, or in the absence of local codes, with the current
CAN/CSA-B149.1 or .2 Installation Code (in Canada) or the current National Fuel Gas Code Z223.1- NFPA 54 when installed in the United States.
This appliance, when installed, must be electrically connected and grounded in accordance with local codes, or in the absence of local codes, with the
current CSA C22.1 Canadian Electrical Code or with the National Electrical Code; ANSI/NFPA 70 when installed in the United States.
In the U.S.A. Thermostats are not permitted for Vented Gas Fireplaces (ANSI Z21.50b-Decorative).
WARNING
FOR SAFE INSTALLATION AND OPERATION OF YOUR GAS FIREPLACE PLEASE NOTE THE FOLLOWING:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
Do not clean when the glass is hot.
Do not use abrasive cleaners.
Using a substitute glass will void all product
warranties.
For safe operation, glass doors must be closed.
When purging the gas line, the glass front must
be removed.
Do not strike or abuse glass. Take care to avoid
breakage.
Do not alter gas orifice.
No substitute materials may be used other than
factory supplied components.
This appliance gives off high temperatures and
should be located out of heavy traffic areas and
away from furniture and draperies.
Children and adults should be alerted to the
hazards of the high surface temperatures of this appliance and should stay away to avoid burns or ignition of clothing.
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children
and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals
in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children and
other at risk individuals out of the room and away from hot surfaces.
Under no circumstances should any solid fuels (wood, paper) be used in this appliance.
Under no circumstances should this appliance be modified. Any parts that have to be removed for servicing should be
replaced prior to operating this appliance.
Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to operating the appliance.
Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at
least annually by a professional service person. More frequent cleaning may be required due to excessive lint from
carpeting, bedding material, et cetera. It is imperative that control compartments, burners and circulating air passageways
of the appliance be kept clean. Make sure that the gas valve and pilot light are turned off before you attempt to clean this
unit.
Clothing or other flammable material should not be placed on or near the appliance. This appliance should not be used as a
drying rack for clothing nor should Christmas stockings or decorations be hung from it.
Do not use this heater if any part has been under water. Immediately call a qualified service technician to inspect the heater
and to replace any part of the control system and any gas control which has been under water.
Do not operate appliance unless completely installed as per installation instructions.
Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this
appliance may result in property damage or personal injury.
Do not operate appliance with the glass front removed, cracked or broken. Replacement of the glass should be done by a
licensed or qualified service person.
The front of the fireplace gives off high temperatures that could ignite combustible material which is kept close to the front of
the unit.
Ensure that power to the Fireplace is turned off before servicing.
Do not operate this Fireplace without the glass front or with a broken glass.
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the
owner’s information manual provided with this appliance. For assistance or additional information consult a qualified
installer, service agency, or the gas supplier.
Operation of this appliance when not connected to a properly installed and maintained venting system or tampering with the
blocked vent shutoff system can result in carbon monoxide (CO) poisoning and possible death.
This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be
plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.
5

Gas fired appliances may be used only for supplemental heat and/or decorative purposes and under no circumstances shall they
provide a primary heat source.

This appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance.
NOTE: It is recommended that a Carbon Monoxide (CO) Detector be installed in or near bedrooms and on all levels of your home.
Place a detector about 15ft [4.5m] outside the room that houses your gas appliance.
Certified for installation in a bedroom or bed/sitting room. In Canada must be installed with listed millivolt thermostat.
In the U.S.A. Thermostats are not permitted for Vented Gas Fireplaces (ANSI Z21.50b-Decorative).
In USA see local codes.
Operations and Maintenance Instructions
For safe installation and operation note the following:
•
Venting systems should be periodically examined by a qualified agency.
•
The flow of combustion and ventilation air must not be obstructed.
•
The Burner/Log Assembly has been engineered and permanently adjusted for proper flame control.
•
Periodically remove the logs from the grate assembly and vacuum any loose particles from the grate and burner areas. See Log
Placement page to remove logs. Vacuum burner parts and replace logs.
•
Never use your gas fireplace as a cooking device.
•
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify
proper operation after servicing.
Installation Requirements for the Commonwealth of
Massachusetts
In the Commonwealth of Massachusetts, the installer or service agent shall be a plumber or gas fitter licensed by the Commonwealth.
When installed in the Commonwealth of Massachusetts or where applicable codes; the unit shall be installed with a CO detector per the
requirements listed below.
1. For direct-vent appliances, mechanical-vent heating appliances or domestic hot water equipment, where the bottom of the vent
terminal and the air intake is installed below four feet above grade the following requirements must be satisfied:
A. If there is not one already present, on each floor level where there are bedroom(s), a carbon monoxide detector and alarm
shall be placed in the living area outside the bedroom(s). The carbon monoxide detector shall comply with NFPA 720.
B. A carbon monoxide detector shall be located in the room that houses the appliance or equipment and shall:
2.

Be powered by the same electrical circuit as the appliance or equipment such that only one service switch services
both the appliance and the carbon monoxide detector;

Have battery back-up power;

Meet ANSI./UL 2034 Standards and comply with NFPA 720; and

Have been approved and listed by a Nationally Recognized Testing Laboratory as recognized under 527 CMR.
C.
A Product-approved vent terminal must be used, and if applicable, a Product-approved air intake must be used.
Installation shall be in strict compliance with the manufacturer’s instructions. A copy of the installation instructions shall
remain with the appliance or equipment at the completion of the installation.
D.
A metal or plastic identification plate shall be mounted at the exterior of the building, four feet directly above the location of
vent terminal. The plate shall be of sufficient size to be easily read from a distance of eight feet away, and read “Gas Vent
Directly Below”.
For direct-vent appliances, mechanical-vent heating appliances or domestic hot water equipment where the bottom of the vent
terminal and the air intake is installed above four feet above grade the following requirements must be satisfied:
A.
If there is not one already present, on each floor level where there are bedroom(s), a carbon monoxide detector and alarm
shall be placed in the living area outside the bedroom(s). The carbon monoxide detector shall comply with NFPA 720.
B. A carbon monoxide detector shall:

Be located in the room that houses the appliance or equipment;

Be either hard-wired or battery powered or both; and

Shall comply with NFPA 720.
A Product-approved vent terminal must be used, and if applicable, a Product-approved air intake must be used. Installation shall be in
strict compliance with the manufacturer instructions. A copy of the installation instructions shall remain with the appliance or equipment
at the completion of the installation.
For the state of Massachusetts a T-handle gas shut-off valve must be used on a gas appliance. This T-handle gas shut-off valve must be listed and
approved by the state of Massachusetts. This is in reference to the state of Massachusetts state code CMR238.
6
Pre-installation Questions and Answers
About curing of the paint
Your stove or fireplace has been painted with the highest quality silicone stove paint. This paint dries quickly in 15-20
minutes when first applied at the factory. However, due to the high temperature silicone components, the paint will cure
when heat is applied to the appliance as it is first used. The following information applies to the curing process to get the
paint fully hard and durable.
Fire the appliance four successive times for 10 minutes each firing and a 5 minute cool down between each. Be aware
during log and firebox paint curing that a white deposit may be developing on the inside of the glass doors. It is important
to remove this white deposit from the glass doors using a commercial fireplace glass cleaner.
•
Babies, small children, pregnant women and pets should leave the area during the cure phase.
•
Ventilate well, open doors and windows.
•
Do not touch during curing.
Why does my fireplace or stove give off odour?
It is normal for your fireplace to give off some odour. This is due to the curing of the paint, adhesives, silicones and any
undetected oil from the manufacturing process as well as the finishing materials used with the installations (e.g. marble,
tile and the adhesives used to adhere this product to the walls can react with heat and cause odours).
It is recommended that you burn your gas fireplace or stove for a minimum of four hours at a time with the fan off (if a fan
is present) after the curing of the paint has been completed. These odours can last upward to 40 hours of burn time; keep
burning at a minimum of four hours per use until odours dissipate.
Noise coming from the fireplace?
Noise is caused by the expansion and contraction of metal as the appliance heats up and cools down. This is normal and
is similar to the sounds produced by a furnace or heating duct. This noise does not affect the operation or longevity of
your fireplace.
Operating Instructions
1. Be sure to read and understand all the instructions in this manual before operation of appliance.
2. Ensure all wiring is correct and properly enclosed to prevent possible shock.
3. Check for gas leaks.
4. Make sure the glass door is properly installed before operation. Never operate the appliance with the glass door
removed.
5. Make sure venting and termination cap are installed and unobstructed.
6. If brick or porcelain liners are used, ensure they are installed.
7. Verify that the pilot can be seen when lighting the appliance. If not, the log or rock placement is incorrect.
8. If the unit is turned off, you must wait a minimum of 60 seconds before re-lighting it.
7
Recommendations for Finishing of Clean View Installations
When finishing the wall around the fireplace, it is critical that the wall covering be fastened properly. It is acceptable to
pre-drill holes and use self-tapping screws which may be used to fasten a backer for tile, marble, etc. Screws being
installed through non-combustible board should be self-tapping type with a maximum length of 2 inches. Wall covering
fasteners, such as screws or nails, are not permitted in some locations.
 Do not drill or install longer screws which may penetrate into the lower panel area as this may damage internal
components.
 Only non-combustible materials may be used over the face of the appliance.
 We recommend that DUROCK (non-combustible material) be tied in to the entire perimeter of framing for durability.
Finishing Recommendations (Obtained from professional construction contractors and finishers):
 Frame unit with metal studs (minimum 20 gauge).
 Minimum of 1/2” DUROCK cement board (this non-combustible panel is ULC listed as a wall shield/floor protector) and
fasten to the entire perimeter framing.
 Use fiberglass (mesh) tape for all joints in area of the fireplace.
 Use Yellow joint mud (contains high amounts of glue) – two coats, finishing with one coat of green topping mud, sand
and prep for painting.
 If not using a surround, a metal “L” Trim may be used to finish perimeter of DUROCK.
 Refer to the following website for more information on using DUROCK Cement Board: www.cgcinc.com
OTHER NOTES:
-A full single sheet of non-combustible board (no joints) above the unit is recommended if possible.
-It is preferred to attach the non-combustible board to framing only and not directly to the unit to allow for expansion and
contraction during normal operation.
-Lighter colored painted surfaces may discolor due to heat exposure.
8
Mobile Home/Manufactured Housing Installation
This Direct Vent System Appliance must be installed in accordance with the manufacturer’s installation instructions and the
Manufactured Home Construction and Safety Standard Title 24 CFR, Part 3280, or the current Standard for Fire Safety Criteria for
Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240 MH Mobile Home Standard in
Canada.
Appliance Must Be Secured To
Structure Using Supplied Nailing
Tabs And Or Fastened To Floor.
Serrated Or Star Washer
Use Existing Hole Or Remove
Existing Screw To Mount Ground
Wire (Nailing Tab Screw).
Ground Wire From Appliance To Steel
Chassis Of Mobile Home. USE 8GA
COPPER WIRE.
THE VENTED GAS FIREPLACE HEATERS (ANSI Z21.88-2009) IN THIS MANUAL MAY BE INSTALLED IN MANUFACTURED
(MOBILE) HOMES AFTER FIRST SALE IN THE USA.
THE VENTED GAS FIREPLACE HEATERS (ANSI Z21.88-2009) IN THIS MANUAL MAY BE INSTALLED IN MANUFACTURED
(MOBILE) HOMES IN CANADA.
Please follow the current ANSI/NFPA 70 National Electrical Code in the USA and CAN/CSA C22.1 Canadian National
Electrical Code in Canada.
An appliance must be grounded to the steel chassis of the home with 8 ga. copper wire using a serrated or star washer to
penetrate paint or protective coating to insure grounding.
Use carriage bolt at the attachment point (see diagram above) to secure the appliance to the floor.
Warning: Do not compromise the structural integrity of the manufactured home wall, floor
or ceiling, during installation of appliance or venting.
For required venting components see venting installation in appropriate section of this manual.
Certified for installation in a bedroom or bed/sitting room. In Canada must be installed with listed millivolt thermostat. In USA see local
codes.
9
ZCV39 / ZCV42
Framing- Nailing Tab Guide
[Qty]2 Nailing Tabs are
located on each side of the
front frame.
These Nailing Tabs can be used in two ways:
1/2” Drywall Flush with Face of Fireplace –
Framing Flush with Face of Fireplace -Fireplace to be covered
with Non-Combustibles (e.g. Concrete Board) for Flat Wall
Fireplace and Combustible Wall to be covered
with a surround or Non-Combustible Materials
appearance.
(e.g. Stone around Fireplace).
Nailing Tab
Nailing Tab
Framing Stud
Framing Stud
Drywall
Drywall
Non-Combustible Material
(eg. Concrete Board)
Non-Combustible
Material (eg. Stone)
Nailing Tab
Framing Mount
Framing Stud
Nailing Tabs
Must Be
Rotated 180°
And Folded
Back Onto
Framing Stud.
Framing Stud
Nailing Tab
Nailing Tab
Flush Surface
10
ZCV39 / ZCV42
Framing Your Gas Fireplace
This section is intended for qualified installers only. Before beginning, make note of where the gas and electrical accesses are
located on the unit. This will streamline the construction process. Furthermore, familiarize yourself with the venting and
clearance requirements (see Venting section) for this appliance. Failure to comply with those requirements can seriously
compromise the safety and operation of the fireplace.
Specifications
1. Cold climate installation recommendation: When installing this fireplace against non insulated exterior wall or chase,
it is recommended that the outer walls be insulated to conform to applicable insulation codes. Drywall & vapor barrier
must be installed over insulation to prevent contact of insulation and unit.
2. Choose fireplace location and frame in accordance with the fireplace framing dimensions specified (view diagrams).
3. Drywall or other combustible material can extend up to the Drywall Stops located on the sides of the unit, and up to
the bottom and top.
4. A Hearth is not required for this unit.
Vertical Venting in Cold Climates
In cold climate conditions where temperatures go below -10 degrees Celsius or 14 degrees Fahrenheit, we recommend
that the chase be insulated and where the vent pipe enters into the attic space that the pipe be wrapped with an
insulated Mylar sleeve. This will increase the temperature of the vent and help the appliance to vent properly in cold
weather conditions.
It is also important in vertical vented direct vent appliances that the appliance be operated daily during the winter months
as this will help stop the termination from freezing up. We recommend using a thermostat (Not permitted for decorative
vented gas fireplaces installed in the U.S.A.) set at room temperature to allow the unit to cycle.
For IPI models it may be necessary to set the appliance to Standing Pilot mode to maintain heat in the cavity. The
purpose of this procedure is to prevent cold air from penetrating the chimney and then onto the living space. Therefore,
when the internal temperature is slightly elevated the fireplace is able to freely exhaust its combustion and hence making
it easier to startup.
Certified for installation in a bedroom or bedsitting room. In Canada must be installed
with listed millivolt thermostat (Not permitted for decorative vented gas fireplaces installed
in the U.S.A.). In USA see local codes.
Stand-off Locations
Make note of where the stand-off locations are. These stand-offs are provided as indicators to illustrate the
boundaries for framing. Therefore, no framing material is permitted to extend beyond these stand-offs.
Caution: Standoffs on top
of the unit must be folded
into position & screwed
down Prior to installation.
Nailing Tabs
Holes are provided in bottom of
unit to secure appliance to floor
after installation.
11
ZCV39
Locating Your Appliance
LOCATION KEY:
A.
Flat on Wall
B.
Across the Corner
C.
As an Island
D.
As a Room Divider
E.
Flat on Wall Corner
F.
Exterior Wall
See Mantel Leg Clearances Instruction for
the proper placement of fireplace.
Island installation with a top vent is
possible as long as the horizontal portion
of the vent system does not exceed 20
feet (6.1 m).
ZCV39
Fireplace Dimensions
FRONT
LEFT SIDE
TOP
12
ZCV39
Framing Dimensions
Determine whether face of fireplace will be:
 Flush with finished wall (e.g., for surround, cultured stone or other non combustible covering).
 Flush with framing (to be covered with concrete board for a Flat Wall appearance).
Refer to Nailing Tab Guide section also. These structures are not load bearing.
Recessed Combustible Wall
Fig. 1
48” MIN for NG
60” MIN for LP
Plus Rise of 1/4”
Per Foot*
RIGHT SIDE
*For Propane Horizontal installations the venting must be an additional one foot above
the minimum vertical rise off the flue before going horizontal.
Vertical Venting MUST maintain 1” clearance to combustibles.
Fig.1
Framing for Horizontal Vent
Termination
(See Installation of Side
Wall Venting Section)
13
ZCV39 Facing Requirements
Required Non-Combustible Areas
NOTE: ANY MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE (Shaded area).
FIREPLACE WITH SCREEN ONLY (AS SHIPPED) SHOWN HERE.
Screens and surrounds with screen require a 5/16” space on all sides to allow for installation & removal.
Refer to Facing Material Dimension Requirements section.
Refer to Facing Material Dimension
Requirements Section.
Note: If using Optional
Surrounds, See
Surround Installations
Section.
Fireplace
Opening 31-9/16”
Minimum NonCombustible (i.e. Concrete
Board, Tile, Brick, etc.)
34-1/2” x 39-1/2”
MIN
Recommended NonCombustible (i.e. Concrete
Board) 39-1/2” x 41”Attached
to Framing
Note: Do not drive excessively long screws into the face of the unit as internal parts may be damaged.
Recessed
Combustible Wall
Recommended NonCombustible (i.e.
Concrete Board) 391/2” x 41”Screwed to
Framing
31-9/16”
Top of
Fireplace
Opening
48” MIN for NG
60” MIN for LP
Plus Rise of
1/4” Per Foot*
This area can have
a combustible
surface (i.e. hearth)
Recommended NonCombustible (i.e. Concrete
Board) Screwed to Framing
14
ZCV39 Facing Material Dimension Requirements
If protruding facing materials (i.e., concrete board, brick or tile) are to be used:




A Tile Lip Kit is available: ZCV-TLK. Follow instructions included with kit to use.
Screens and surrounds with screen require a minimum 5/16” space on top to allow for installation &
removal.
NOTE: ANY MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE
See below for dimension requirements.
For Fireplace with Screen Only -OR- ZCV39S2PF Surround with Screen & max. 1/2” Non-Combustible behind Face:
Top Clearance from Opening =
Non-Combustible
material ONLY over
front of fireplace
ZCV39CSS
Fireplace Opening
Side & Bottom Clearance from Opening =
For ZCV39S2PF Surround with Screen and Facing Materials Up to Edge of Surround:
NOTE: The ZCV39S2PF surround will install over non-combustible 1/2”thick max.
For thicker facing materials, DO NOT bring closer than within 5/16” of top edge of surround.
Top Clearance from Opening =
Non-Combustible
material ONLY over
front of fireplace
ZCV39S2PF
with
ZCV39CSS
Fireplace
Opening
Side & Bottom Clearance from Opening =
(Continued)
15
ZCV39 Facing Material Dimension Requirements (Continued)
If protruding facing materials (i.e., concrete board, brick or tile) are to be used:

A Tile Lip Kit is available: ZCV-TLK. Follow instructions included with kit to use.

Screens and surrounds with screen require a minimum 5/16” space on top to allow for installation & removal.

See below for dimension requirements.
For Fireplace with Screen and ZCV39S1 Hearth Mount Surround:
ZCV39S1 With ZCV39CSS
Top Clearance from Opening =
Fireplace
Opening
Side Clearance from Opening =
For Fireplace With Screen And ZCV39S1PF 4” Picture Frame Surround:
ZCV39S1PF with ZCV39CSS
Top Clearance from Opening =
Fireplace
Opening
Side & Bottom Clearance from Opening =
16
MQZCV39DD Designer Door
Facing Material Dimension Requirements
If protruding facing materials (i.e., concrete board, brick or tile) are to be used:
 A Tile Lip Kit is available: ZCV-TLK. Follow instructions included with kit to use.
 A minimum 1/8” space on top & sides is required to allow for installation & removal.
 NOTE: ANY MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE
 See below for dimension requirements.
Non-Combustible
material ONLY over
front of fireplace
Clearance from top of Opening =
Clearance from
sides of Opening
Fireplace
Opening
Clearance from bottom of Opening =
ZCV-TLK
Tile Lip Kit
Optional Tile Lip Kit:
NOTE: ANY MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE
Instructions: -Refer to the charts below to find your installation choice.
-Cut [2] tile lip pieces to height of sides, and [2] to length of top & bottom.
-Install onto face of fireplace so that screwing flange will be beneath facing materials.
39ZCV
Fireplace Facing Choice
Height of
Side Pieces
Side Clearance
from Opening
Length of Top &
Bottom Pieces
Top Clearance
from Opening
Bottom Clearance
from Opening
31-9/16”
1”
35”
1-3/16”
1”
31-9/16”
1”
35”
1-3/16”
1”
ZCV39S2PF Surround
-Facing Materials Up to
Edge of Surround
33-1/16”
1-3/4”
36-1/2”
1-15/16”
1-3/4”
ZCV39S1 Hearth Mount
Surround
35-7/16”
4”
41”
(Top Only
Required)
4-1/16”
No Bottom piece
required
ZCV39S1PF 4” Picture
Frame Surround
37-7/16”
4”
41”
4-1/16”
4”
MQZCV39DD Designer
Door
34-1/2”
2-5/8”
38-1/4”
3-1/8”
2”
(No Bottom piece
required if installed at
hearth level)
Screen Only
ZCV39S2PF Surround
-with 1/2” thick facing
material behind
17
39ZCV
Mantel Clearances
Before installing any mantels it is
important to determine the combustibility
of its material(s). There are two types of
mantels to consider: Combustible and
Non-Combustible.
A Combustible Mantel is one that
consists of material(s) that may discolor,
combust, or lose its integrity in the
presence of heat. These types of mantels
must strictly conform to the dimensional
requirements shown.
Conversely, a Non-Combustible Mantel
is one that is constructed with material(s)
that will not combust. Check your local
codes and regulations to determine
whether your mantel is combustible or
Non-Combustible.
The advantage to Non-Combustible
Mantels is that it may extend right up to
the tile lip of the fireplace. Combustible
mantels must adhere to the dimensional
restrictions shown.
-Combustible Objects on NonCombustible Mantel WarningCombustible objects must not be placed
on a Non-combustible Mantel unless the
mantel meets the dimensional
requirements for a Combustible Mantel.
Determine whether your mantel
conforms to the requirements of a
Combustible Mantel.
Mantel
Dimensions are
from front face or
Non-Combustible
Facing Materials
covering fireplace.
Mantel Leg Clearances
Top View
Adjacent Wall
Adjacent Wall
18
ZCV39 Clearance to Combustibles
Clearance to Combustibles
ZCV39
Front
36” [92cm]
Back (from Stand-offs)
0” [0cm]
Side (from Stand-offs)
0” [0cm]
Floor*
0” [0cm]
Minimum Ceiling Height (from bottom of fireplace)
55-1/2” [141cm]
Top (from Stand-offs)
0” [0cm]
Top of 90° Bend in minimum Enclosure of 55-1/2”
4” [10.2cm]
Top of 90° Bend in Enclosure over 55-1/2”
4” [10.2cm]
VENTING SYSTEMS
Top of Horizontal Pipe
1/1/2” [3.8cm]
Side & Bottom of Horizontal Pipe
1” [2.5cm] All Vent Systems
Vertical Vent Pipe
1” [2.5cm] All Vent Systems
48” MIN for NG
60” MIN for LP
Plus Rise of 1/4”
Per Foot*
*Note: If appliance is installed directly on
carpeting or other combustible material
other than wood flooring, a metal or wood
panel extending the full width and depth of
the appliance must be used. Carpet may
extend 1 inch above the floor of the
appliance.
19
ZCV42
Locating Your Appliance
LOCATION KEY:
A.
Flat on Wall
B.
Across the Corner
C.
As an Island
D.
As a Room Divider
E.
Flat on Wall Corner
F.
Exterior Wall
See Mantel Leg Clearances Instruction for
the proper placement of fireplace.
Island installation with a top vent is
possible as long as the horizontal portion
of the vent system does not exceed 20
feet (6.1 m).
ZCV42
Fireplace Dimensions
FRONT
LEFT SIDE
TOP
20
ZCV42
Framing Dimensions
Determine whether face of fireplace will be:
 Flush with finished wall (e.g., for surround, cultured stone or other non combustible covering).
 Flush with framing (to be covered with concrete board for a Flat Wall appearance).
Refer to Nailing Tab Guide section also. These structures are not load bearing.
Recessed Combustible Wall
Fig. 1
52-1/2” MIN for NG
64-1/2” MIN for LP
Plus Rise of 1/4” Per
Foot*
RIGHT SIDE
*For Propane Horizontal installations the venting must be an additional one foot above
the minimum vertical rise off the flue before going horizontal.
Vertical Venting MUST maintain 1” clearance to combustibles.
Fig.1
Framing for Horizontal Vent
Termination
(See Installation of Side
Wall Venting Section)
21
ZCV42 Facing Requirements
Required Non-Combustible Areas
NOTE: ANY MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE (Shaded area).
FIREPLACE WITH SCREEN ONLY (AS SHIPPED) SHOWN HERE.
Screens and surrounds with screen require a 5/16” space on all sides to allow for installation & removal.
Refer to Facing Material Dimension Requirements section.
Refer to Facing Material Dimension
Requirements Section.
Note: If using Optional
Surrounds, See
Surround Installations
Section.
Fireplace
Opening
34-11/16”
MIN
Minimum NonCombustible (i.e. Concrete
Board, Tile, Brick, etc.)
37-5/8” x 42-1/2”
Recommended NonCombustible (i.e. Concrete
Board) 42-5/8” x
44”Screwed to Framing
Note: Do not drive excessively long screws into the face of the unit as internal parts may be damaged.
Recommended
Non-Combustible
(i.e. Concrete Board)
42-5/8” x 44”Screwed
to Framing
Recessed
Combustible Wall
52-1/2” MIN for NG
64-1/2” MIN for LP
Plus Rise of 1/4”
Per Foot*
34-11/16”
Top of
Fireplace
Opening
This area can have
a combustible
surface (i.e. hearth)
Recommended
Non-Combustible
(i.e. Concrete
Board) Screwed to
Framing
22
ZCV42 Facing Material Dimension Requirements
If protruding facing materials (i.e., concrete board, brick or tile) are to be used:




A Tile Lip Kit is available: ZCV-TLK. Follow instructions included with kit to use.
Screens and surrounds with screen require a minimum 5/16” space on top to allow for installation &
removal.
NOTE: ANY MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE
See below for dimension requirements.
For Fireplace with Screen Only –OR- ZCV42S2PF Surround with Screen & max. 1/2” Non-Combustible behind Face:
Non-Combustible
material ONLY over
front of fireplace
ZCV42CSS
Top Clearance from Opening =
Fireplace Opening
Side & Bottom Clearance from Opening =
For ZCV42S2PF Surround with Screen and Facing Materials Up to Edge of Surround:
NOTE: The ZCV42S2PF surround will install over non-combustible 1/2”thick max.
For thicker facing materials, DO NOT bring closer than within 5/16” of top edge of surround.
Non-Combustible
material ONLY over
front of fireplace
Top Clearance from Opening =
ZCV42S2PF With
ZCV42CSS
Fireplace
Opening
Side & Bottom Clearance from Opening =
(Continued)
23
ZCV42 Facing Material Dimension Requirements (Continued)
If protruding facing materials (i.e., concrete board, brick or tile) are to be used:

A Tile Lip Kit is available: ZCV-TLK. Follow instructions included with kit to use.

Screens and surrounds with screen require a minimum 5/16” space on top to allow for installation & removal.

See below for dimension requirements.
For Fireplace with Screen and ZCV42S1 Hearth Mount Surround:
ZCV42S1 With
ZCV42CSS
Top Clearance from Opening =
Fireplace Opening
Side Clearance from Opening =
For Fireplace With Screen And ZCV42S1PF 4” Picture Frame Surround:
ZCV42S1PF With
ZCV42CSS
Top Clearance from Opening =
Fireplace Opening
Side & Bottom Clearance from Opening =
24
MQZCV42DD Designer Door
Facing Material Dimension Requirements
If protruding facing materials (i.e., concrete board, brick or tile) are to be used:
 A Tile Lip Kit is available: ZCV-TLK. Follow instructions included with kit to use.
 A minimum 1/8” space on top & sides is required to allow for installation & removal.
 NOTE: ANY MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE
 See below for dimension requirements.
Clearance from top of Opening =
Clearance from
sides of Opening
Fireplace Opening
Clearance from bottom of Opening =
ZCV-TLK
Tile Lip Kit
Optional Tile Lip Kit:
NOTE: ANY MATERIALS COVERING THE FACE OF THE FIREPLACE MUST BE NON-COMBUSTIBLE
Instructions: -Refer to the charts below to find your installation choice.
-Cut [2] tile lip pieces to height of sides, and [2] to length of top & bottom.
-Install onto face of fireplace so that screwing flange will be beneath facing materials.
ZCV42
Fireplace Facing
Choice
Height of
Side Pieces
Side Clearance
from Opening
Length of Top &
Bottom Pieces
Top Clearance
from Opening
Bottom Clearance
from Opening
Screen Only
34-11/16”
1”
39-1/16”
1-3/16”
1”
34-11/16”
1”
39-1/16”
1-3/16”
1”
ZCV42S2PF Surround
-Facing Materials Up to
Edge of Surround
36-3/16”
1-3/4”
40-9/16”
1-15/16”
1-3/4”
ZCV42S1 Hearth
Mount Surround
38-9/16”
4”
45-1/16”
(Top Only
Required)
4-1/16”
No Bottom piece
required
ZCV42S1PF 4” Picture
Frame Surround
40-9/16”
4”
45-1/16”
4-1/16”
4”
MQZCV42DD
37-5/8”
2-9/16”
42-1/4”
3-1/8”
2”
(No Bottom piece
required if installed
at hearth level)
ZCV42S2PF Surround
-with 1/2” thick facing
material behind
Designer Door
25
42ZCV
Mantel Clearances
Before installing any mantels it is
important to determine the
combustibility of its material(s). There
are two types of mantels to consider:
Combustible and Non-Combustible.
A Combustible Mantel is one that
consists of material(s) that may
discolor, combust, or lose its integrity
in the presence of heat. These types
of mantels must strictly conform to the
dimensional requirements shown.
Conversely, a Non-Combustible
Mantel is one that is constructed with
material(s) that will not combust.
Check your local codes and
regulations to determine whether your
mantel is combustible or NonCombustible.
The advantage to Non-Combustible
Mantels is that it may extend right up
to the tile lip of the fireplace.
Combustible mantels must adhere to
the dimensional restrictions shown.
-Combustible Objects on NonCombustible Mantel WarningCombustible objects must not be placed
on a Non-combustible Mantel unless the
mantel meets the dimensional
requirements for a Combustible Mantel.
Determine whether your mantel
conforms to the requirements of a
Combustible Mantel.
Mantel Dimensions
are from front face
or Non-Combustible
Facing Materials
covering fireplace.
Mantel Leg Clearances
Top View
Adjacent Wall
Adjacent Wall
26
ZCV42 Clearance to Combustibles
Clearance to Combustibles
ZRB46
Front
36” [92cm]
Back (from Stand-offs)
0” [0cm]
Side (from Stand-offs)
0” [0cm]
Floor*
0” [0cm]
Minimum Ceiling Height (from bottom of fireplace)
59.5” [151cm]
Top (from Stand-offs)
0” [0cm]
Top of 90° Bend in minimum Enclosure of 59.5”
3-1/2” [8.9]
Top of 90° Bend in Enclosure over 59.5”
3-1/2” [8.9]
VENTING SYSTEMS
Top of Horizontal Pipe
1/1/2” [3.8cm]
Side & Bottom of Horizontal Pipe
1” [2.5cm] All Vent Systems
Vertical Vent Pipe
1” [2.5cm] All Vent Systems
52-1/2” MIN for NG
64-1/2” MIN for LP
Plus Rise of 1/4”
Per Foot*
*Note: If appliance is installed directly on
carpeting or other combustible material
other than wood flooring, a metal or wood
panel extending the full width and depth of
the appliance must be used. Carpet may
extend 1 inch above the floor of the
appliance.
27
ZCV39CSS / ZCV42CSS
Child Safety Screen Installation
Contents of Kit:
[1] Child Safety Screen- Ready to
Install
Assembly Instructions:
Attach screen to fireplace as per
instructions below.
⚠WARNING:
Wait until unit is COMPLETELY
cool before touching glass or
attempting to install or remove
Child Safety Screen.
Place hook at
bottom of
screen onto
frame of
fireplace below
Access Panel.
Push top of screen
up against fireplace
and hook onto
screws in side frame.
Push down on
screen to lock in
place.
Screen is locked in place.
To remove Safety Screen, WAIT UNTIL FIREPLACE IS COMPLETELY COOL. Push up at center of Screen Frame
and pull bottom away from fireplace.
28
ZCV39 / ZCV42
Surround Installations
Each Kit contains surround and [8] DT screws.
NOTE: ZCV39CSS or ZCV42CSS Safety Screen is required to use these surrounds.




All surrounds are mounted onto Screen as described below. Screen and surround are then mounted on unit as described in
Child Safety Screen Installation section.
Surrounds require a 5/16” space on top to allow for installation & removal.
If protruding facing materials (i.e., concrete board, brick or tile) are to be used, refer to Facing Material Dimension
Requirements section.
A Tile Lip Kit is available: ZCV-TLK. Follow instructions included with kit to use.
ZCV39S1 / ZCV39S1PF/ ZCV39S2PF / ZCV42S1 / ZCV42S1PF / ZCV42S2PF
To Attach Surround to Screen:
1. Place surround face down on protected
surface.
2. Lay Screen onto back side of surround.
3. Fold up tabs on top & bottom of surround.
4. Drive screws into screen through holes in
top & sides as shown.
Install Screen with Surround attached as described in in Child Safety Screen Installation section.
29
MQZCV39DD / MQZCV42DD
Designer Door Installations
Each Kit contains: Back Frame, Front Frame, and Screen.



If protruding facing materials (i.e., concrete board, brick or tile) are to be used, refer to Facing Material Dimension
Requirements section.
Designer Doors require a minimum 1/8” space on top and sides to allow for installation & removal.
A Tile Lip Kit is available: ZCV-TLK. Follow instructions included with kit to use.
To Assemble Designer Door:
1. Slide Screen into Front Frame.
2. Set Hinge Sockets on Front Frame onto
Hinge Pins of Back Frame.
Back Frame
Front Frame
To Install Designer Door:
1. Remove Front Frame from Back
Frame.
2. Set Back Frame onto Lower Ledge
of fireplace below Access Panel.
3. Use Screws in top corners of
fireplace frame sides to attach
Back Frame to fireplace.
4. Insert Screen into Front Frame.
5. Set Hinge Sockets on Front Frame
onto Hinge Pins of Back Frame.
30
ZCV39 / ZCV42
51UHS Box
Included with base model.
The 51-UHS is designed for millivolt and IPI units for in-unit installation of the Remote Receiver, Fan Control Module, and the IPI
Module. 51-UHS can be inserted & removed from beneath fireplace through access panel opening (Remove glass door first).
NOTE: When using a remote control, the 51-UHS must be used. Batteries for Remote Receiver can be changed by lifting 51-UHS up
through opening.
IPI Module
Remote Receiver
Access Panel
51-UHS Box
Fan Control Module
51-UHS can be inserted & removed from beneath fireplace through access panel opening (Remove glass door first).
Batteries
COMPONENT LOCATIONS
NOTE: The gas line
connection may be made of
1/2” rigid pipe or an
Approved Kingsman Flex
Connector, such as
FP15GC. Since some
municipalities have
additional local codes, it is
always best to consult your
local authorities and the
current CAN/CGA - B149.1
or .2 installation code in
Canada or the National
Fuel Gas code ANSI
Z223.1 in the U.S.A
(See Each Section For Connections & Wiring)
Fan
Gas line
Power Vent Control Module
Valve
ULK Transformer
UHS Box
31
ZCV39 / ZCV42
Z46FK Fan Kit Installation
The fan can be installed through
the side of the fireplace.
If fireplace is already installed, the
burner pan must be removed to
install the fan (See Burner System
Removal section).
⚠ WARNING
Electrical Grounding Instructions
This appliance is equipped with a three prong (grounding) plug for your protection against
shock hazard and should be plugged directly into a properly grounded three-prong
receptacle. Do not cut or remove the grounding prong from this.
Before Servicing
1.
2.
Ensure all power supply is shut off.
Label all wires prior to disconnecting when servicing control. Wiring errors can cause
improper and dangerous operation.
For fan servicing: Vacuum and clean lint/dirt build-up on the fan blades and motor.
When resealing the Burner Pan, use Mill Pac.
To install the fan from the side of
the unit, remove the two screws in
3.
the Fan Access Cover on the left side
4.
of the fireplace. Bend the cover up
and pull bottom tab down. Insert fan through opening as shown.
Mount fan on tabs in bottom of fireplace. Connect fan as per wiring diagram below. Replace all components.
Fan Speed Control is located outside of fireplace. Thermodisc is Located under Burner pan.
NOTE: Do not allow cords or wires to come
into contact with the firebox or the underside
of the burner pan.
Fan Mount Tabs
Fan Speed
Control
(Located
Outside of
Fireplace)
Thermodisc
Located under Burner pan
32
Split Receptacle-
Fan Speed Control Outside of Fireplace
If you plan to locate the variable speed control switch for the fan outside of the fireplace and you require a constant source
of AC power inside the unit for another accessory such as lights or an IPI valve system, follow one of the procedures
below.
WARNING
A qualified electrician must connect
electrical wiring to junction outlet for
built-in installation.
Follow all codes.
WARNING
Electrical Grounding Instructions –
This appliance is equipped with a
three – pronged (grounding) plug for
your protection against shock hazard
and should be plugged directly into a
properly grounded three-prong
receptacle.
WARNING
Label all wires prior to disconnection
when servicing controls. Wiring errors
can cause improper and dangerous
operation. Verify proper operation and
servicing.
Caution: Electrical installation to be done by a qualified installer. All wires must be connected and grounded in accordance with
CSA Standard C22.1- Canadian Electrical Code part 1 or with the National Electrical Code, ANSI /NFPA 70 (latest edition) and /or in
accordance with local codes.
Switch Controlled Split Receptacle With Switch At START Of Cable Run
Switch Controlled Split Receptacle With Switch At END Of Cable Run
33
ZCV39PL / ZCV42PL
Liner Installation
⚠ WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
ZCV39PL / ZCV42PL Consists of:
[1] – Back Liner
[1] – Left Side Liner
[1] – Right Side Liner
[2] – Liner Retainer Clips
Step One: Remove Log Holder.
Step Two: Place Back Liner against back wall of firebox.
NOTE: For Heater Rated units (ZCV39NH, ZCV39NEH,
ZCV39LPH, ZCV39LPEH, ZCV42NH, ZCV42NEH,
ZCV42LPH, and ZCV42LPEH) burner must be removed. See
Burner Removal section of manual.
Step Three: Tilt and slide left and right Side Liners
into place.
Step Four: Fix Side Liners in place using Liner Retainer Clips.
Step Five: Reinstall all components.
⚠ Note: Warping and Discoloration of Porcelain or Painted Metal Liners Is Not Covered Under Warranty.
Both Porcelain and Painted Metal Liners may discolor and warp during normal operation of your appliance.
This is normal, and not considered a defect.
34
ZCV39RL / ZCV42RL Brick Liner Installation
⚠ WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
Step One: Remove Log Holder.
Step Two: Place Back Liner against back wall of firebox.
NOTE: For Heater Rated units (ZCV39NH, ZCV39NEH,
ZCV39LPH, ZCV39LPEH, ZCV42NH, ZCV42NEH,
ZCV42LPH, and ZCV42LPEH) burner must be removed.
See Burner Removal section of manual.
Step Three: Tilt and slide left and right Side
Liners into place.
Step Four: Fix Side Liners in place using Liner
Retainer Clips.
Step Five:
Reinstall Log
Holder.
35
ZCV39GT/ ZCV42GT
Glass Tray Setup
Parts List: [1] Glass Tray,[2] Pilot Shields, [1] Glass Retainer, [3] DT Screws.
Installation: Remove Log Holder and Log Grate.
Place Glass Tray over Burner. Insert Pilot Cover into slots in Glass Tray.
Glass Tray sits behind Door Latch Screws.
⚠ WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
DO NOT COVER PILOT SHIELD AREA WITH MEDIA.
Visually Inspect Pilot Shield Monthly
for signs of deterioration due to flame
exposure. Replace if necessary.
Glass Tray sits behind Door Latch Screws.
Glass Retainer may be attached to Glass Tray if desired.
36
ULK2
Universal Light Kit (Optional Accent Lighting Kit)
Please follow the current ANSI/NFPA 70 National Electrical Code in the USA and CAN/CSA C22.1 Canadian
National Electrical Code in Canada.
Contents of Kit:




[2] 12V Halogen Lamps
Lamp Plate with Insulated Studs & wiring
12VAC Transformer with 3 prong plug & wire connectors
Light Switch & Cover Plate c/w10ft wire c/w [1] Loose
Female & [1] Loose Male wire connector
Lamp
Lamp
Inside Firebox
Bottom of Firebox
Connect Switch Here
NOTE: Must be used with ZCV39GT/ ZCV42GT Glass Tray
INSTALLATION:
STEP 1: Remove Burner (See Burner Removal Section). Remove Cover Plate. Remove old sealant.
STEP 2: Insert lamp wires through access hole in firebox as above. Apply new sealant (Mill-Pac). Secure Lamp Plate
with screws.
37
Screw
Screw
ZCV39 / ZCV42
STEP 3: Place Lamps in position in firebox. Attach to fireplace with a single screw at the locations shown above for
each unit. Lamps can be placed facing upward or sideways. Replace burner and false bottom if used, along with pilot
shield.
STEP 4: Connect switch wires between
lamp wire and transformer (see
schematic). Connect remaining lamp wire
to transformer. Transformer can then be
plugged in and the housing fastened to
the bottom of the fireplace.
Glass may be used to cover perforations in false bottom
ULK
TRANSFORMER
ASSEMBLY
120 VAC
ULK TRANSFORMER ASSEMBLY WHEN PLUGGED INTO FAN CONTROL MODULE
38
ZCV39 / ZCV42
Log F3
Pull Up [4] Log Tabs
*Lava Rock
*Embers
*Insulation
Wool
*Vermiculite
*These items are supplied with the fireplace.
Pull up [4] Log Tabs on Burner.
Match with Holes in Logs 3 & 4.
2
1
Logs 1 & 2 are placed against back wall of firebox.
4
3
Logs 3 & 4 are placed onto Log Tabs on Burner.
Embers & Insulation
Wool on Burner
Lava Rock & Vermiculite
on Firebox Bottom
⚠ WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
39
RBCB1
-Cannonballs-
Installation Instructions
*Must be used with ZCV39GT/ ZCV42GT Glass Tray
Assorted size and colors. Place randomly as desired inside fireplace.
Can be used with MQ Glass, MQ Ember, and / or Lava Rock. Do not place Cannonballs directly on burner ports.
If sooting occurs change position of or remove affected objects.



MQ Glass can be placed directly on Burner and on Glass Tray.
MQ Ember can be placed directly on Burner Only.
Lava Rock (Supplied with Base Unit) CANNOT be placed on Burner. Place Lava Rock in channel in front of
Glass Tray & on Glass Tray.
NOTE
 Pilot Area Must Not Be Covered, as delayed ignition can occur.
 Do not place Cannonballs directly on burner ports.
Pilot Area Must Not
Be Covered
*Pilot Shield should be visually
inspected monthly for signs of
deterioration due to flame
exposure. Replace if necessary.
40
MQ Dealer Accessories for ZCV39 / ZCV42
The following Accessories are available through MQ Dealers only.
ACCESSORY ITEM
MQG5W*
MQG5A*
MQG5B*
DESCRIPTION
Decorative Glass 1/2” White
Decorative Ember Glass Cobalt Blue
Decorative Ember Glass - Black
MQG5ZG*
Decorative Glass- Zircon Glacier Ice
NOTE: All glass is sold in 5 pound bags.
MQ39D*
Driftwood Log Set- 4pcs.
MQROCK2*
Rock Set Natural
MQROCK3*
Rock Set Multi-Color
MQSTONE*
Decorative Stones
MQEMBER*
Glowing Embers
MQLOG F9
Log Set- 9pcs

GLASS (MQG5W, MQG5C, MQG5A, MQG5B, MQG5ZG)
If you wish to use this media evenly spread the glass embers onto the
false bottom and burner. Ensure the glass embers do not excessively
overlap as this will affect the flame pattern. Use care when placing
glass embers near the pilot area so as not block or have the glass fall
over the crossover holes from the pilot to the burner, as delayed
ignition can occur.
The following types of glass are approved:
 ½” Ember Glass Material from American Fireglass.
Maximum amount: ZCV39: Natural Gas is 15 lbs., Propane units 15 lbs.
ZCV42: Natural Gas is 20 lbs., Propane units 20 lbs.
 Liquid Glass from Firegear.
Maximum amount: ZCV39: Natural gas is 15 lbs.
ZCV42: Natural gas is 20 lbs.
Not recommended for Propane appliances.
*Must be used with ZCV39GT/ ZCV42GT Glass Tray
Use of any other glass can alter the performance of the unit and is not covered
under warranty.
Discoloration of glass media may occur if placed on the burner, this is not
covered under warranty.
Pilot Area Must Not
Be Covered
*Pilot Shield should be visually
inspected monthly for signs of
deterioration due to flame
exposure. Replace if necessary.

MQG5ZG Decorative Glass- Zircon Glacier Ice (15Lbs. for ZCV39 / 20Lbs. for ZCV42)

Must be used with ZCV39GT/ ZCV42GT Glass Tray
NOTE
 Pilot Area Must
Not Be
Covered, as
delayed ignition
can occur.
Glass Retainer (supplied with Glass Tray)
may be attached to Glass Tray if desired.
41
MQ39D Driftwood Log Set- 4pcs - Must be used with ZCV39GT/ ZCV42GT Glass Tray
NOTE
2
 Pilot Area Must
Not Be
Covered, as
delayed ignition
can occur.
1
3
4
Insulation Wool & MQ EMBER (shown,
supplied with Base Unit), or MQ Glass can
be placed on Burner.
MQ Stone (shown), MQ
Rock 2 or 3, or MQ Glass
can be placed on Glass Tray.
Lava Rock (supplied with Base Unit).
Do not place on Burner.
 Place Log 1 on left side of fireplace against the back wall of the firebox.
 Place Log 2 on the right side of fireplace against the back wall of the firebox as shown.
 Pull up Log Tabs on Burner. Match these with holes in bottom of logs 3 & 4.
 Place Logs 3 & 4 on the burner in the center of fireplace as shown. Do not place directly on burner ports.
 If sooting occurs change position of logs or remove affected objects.
MQROCK2, MQROCK3 - Must be used with ZCV39GT/ ZCV42GT Glass Tray
MQRock2
Or
MQRock3
MQ EMBER (shown) can be
placed on Burner.
MQ Glass can be placed on
Burner and Glass Tray.
Lava Rock (Supplied with Base
Unit). Do not place on Burner.
 Place rocks randomly onto False Bottom and Burner. Do not place directly on burner ports.
 Not all rocks will be used on some installations.
 If sooting occurs change position of or remove affected objects.
NOTE
 Pilot Area Must Not Be Covered, as delayed ignition can occur.
42
MQ STONE DECORATIVE STONE SET- Must be used with ZCV39GT/ ZCV42GT Glass Tray
MQ Stone can be placed
on or around Burner.
Lava Rock (Supplied with Base
Unit). Do not place on Burner.
MQ EMBER (shown) can be placed on Burner.
MQ Glass can be placed on Burner and Glass Tray.
 Place Stones onto False Bottom and Burner. Do not place directly on burner ports or Pilot Area.
 Not all stones will be used on some installations.
 If sooting occurs change position of or remove affected objects.
 MQEMBER To be placed directly on Burner and Burner Ports.
 Place these glowing ember chunks randomly. May be used with or without other accessories.
Pilot Area Must Not
Be Covered
*Pilot Shield should be visually
inspected monthly for signs of
deterioration due to flame
exposure. Replace if necessary.
NOTE
 Pilot Area Must Not Be Covered, as delayed ignition can occur.
43
MQ Log F9 Setup
Pull Up [4] Log Tabs
5
2
1
6
3
4
*Embers
7
*Lava Rock
9
8
Pull up [4] Log Tabs on Burner.
Match with Holes in Logs 3 & 4.
*Insulation Wool
*Vermiculite
*These items are supplied with the fireplace.
2
1
Logs 1 & 2 are placed against back wall of firebox.
5
6
3
4
Logs 3 & 4 are placed onto Log Tabs on Burner.
(Continued)
44
⚠ WARNING: Failure to position the parts in accordance with these diagrams or failure to use only
parts specifically approved with this appliance may result in property damage or personal injury.
7
8
9
Embers &
Insulation Wool
on Burner
Lava Rock &
Vermiculite on
Firebox Bottom
45
Door and Glass Information
Glass Cleaning
It will be necessary to clean the glass periodically. During startup, condensation, which is normal, forms on the inside of the glass, and
causes dust, lint etc. to cling to the glass surface.
Also, initial paint curing can deposit a slight film on the glass. It is therefore recommended that initially the glass be cleaned two or three
times with a commercial fireplace glass cleaner. After that, the glass should be cleaned two or three times a season depending on the
circumstances.
⚠ Cautions and Warnings
 Do not clean when the glass is hot.
 The use of substitute glass will void all product warranties (see Glass Replacement in this section).
 Care must be taken to avoid breakage of the glass.
 Do not operate this fireplace without the glass front or with a broken glass front.
 Do not strike or abuse the glass.
Glass Replacement
ZCV39N, ZCV39NE, ZCV39LP, ZCV39LPE, ZCV42N, ZCV42NE, ZCV42LP, ZCV42LPE must use tempered glass. Must be 5mm thick.
Only Robax ceramic or coated Neoceram glass may be used for replacement for Models ZCV39NH, ZCV39NHE, ZCV39LPH,
ZCV39LPHE, ZCV42NH, ZCV42NHE, ZCV42LPH, and ZCV42LPHE. Glass must be minimum 5mm thick.
To replace glass, clean all materials from the door frame. Scrape off old silicone all the way down to the metal. Using high-temp silicone
[rated up to 500°F (260°C)] apply a continuous bead of approximately 1/8”-3/16” to all four [4] sides of the frame. With the frame resting
on a flat surface, insert the new glass with a new gasket. Gently press the glass into the silicone. Be careful not to use excessive force
on the glass. Let the silicone dry for approximately 15-20minutes.
Use caution when removing broken glass. Wear gloves.
Removal of the Glass Door
1.
2.
3.
Remove the door by unlatching the 2 top latches. Simply place 2 fingers in the grooves, and pull and lift upward slightly.
Once the top of the door is unlatched, pull it outward and lower it to unlatch the bottom.
To re-install, place the Bottom Door Ledge into the 2 Lower Latch assemblies first. Then swing the door closed to seal it against
the firebox cavity. Re-latch the Upper Latch assembly to secure the door to the appliance.
Spring Replacement
1.
2.
3.
Latch Assembly
51MQ-123A
*Over time, the door latch spring (Part#36HB-123) may
need to be replaced if tension is lost.
To replace latch spring, remove the 2 hex screws
(located in the firebox) that secure the latch assembly
in place.
Once the screws are removed the latches will slide out
of place.
Remove the locknut from the latch assembly and
replace the spring. Re-tighten the locknut until 2 thread
turns are beyond the locknut. This is critical for proper
tension. Replace latch assembly.
46
Gas Line Installation
This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CAN/CGA B149.1 or .2 installation codes for Gas Burning appliances and equipment in Canada and the National Fuel Gas Code ANSI Z223 in
the U.S.A.
1. The gas pipeline can be brought in through
either the right or the left side of the appliance.
3/8” UNION
A knockout is provided at either location to allow
for the gas pipe installation and testing of any
gas connection.
2. The gas control inlet is 3/8” NPT. Typical
1/2” X 3/8” SHUTOFF
installation layout for rigid pipe is shown at right.
VALVE
3. When using copper or flex connector, use
only approved fittings. Always provide a union
so that gas line can be easily disconnected for
burner or fan servicing. See gas specification for
pressure details and ratings.
4. When a vertical section of gas pipe is
3/8” NIPPLE
1/2” GAS SUPPLY
required for the installation, a condensation trap
is needed. See CAN/CGA-B149.1 or .2 for code
details.
5. For natural gas, a minimum of 3/8” iron pipe with gas minimum pressure of 4.5” w.c. must be used for supply from the gas meter.
Consult with the local gas utility if any questions arise concerning pipe sizes.
6. A 1/8” NPT plugged tappings are accessible for test gauge connection both on the inlet and outlet of the gas valve.
7. Turn the gas supply ON and check for leaks. DO NOT USE OPEN FLAME FOR THIS PURPOSE. Use an approved leak testing
solution.
8. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure
testing of that system at test pressures in excess of 1/2 PSIG (3.5 KPa).
9. The appliance must be isolated from the gas supply piping system by closing its individual shutoff valve during any pressure
testing of the gas sup- ply piping system at test pressures equal to or less than 1/2 PSIG (3.5 KPa).
NOTE: The gas line connection may be made of 1/2” rigid pipe or an Approved Kingsman Flex Connector, such as FP15GC.
Since some municipalities have additional local codes, it is always best to consult your local authorities and the current CAN/CGA B149.1 or .2 installation code in Canada or the National Fuel Gas code ANSI Z223.1 in the U.S.A
For the state of Massachusetts a T-handle gas
shut-off valve must be used on a gas
appliance. This T-handle gas shut-off valve
must be listed and approved by the state of
Massachusetts. This is in reference to the state
of Massachusetts state code CMR238.
Important: Always check for gas leaks with a
soap and water solution. Do not use open flame
for leak testing.
Gas Specifications
MODELS
Fuel
Gas
Control
ZCV39N/NE
Natural
Millivolt / IPI
ZCV39LP/LPE
Propane
Millivolt / IPI
ZCV39NH/NHE
Natural
Millivolt / IPI
INPUT
Maximum
25,000 BTU
25,000 BTU
28,000 BTU
Low
16,750 BTU
20,000 BTU
19,000 BTU
Orifice
#38
1/16”
#37
Size
(0-4500ft)
Air
1/16”
Fully Open
1/16”
Shutter
Gas Inlet Size S.I.T. 820 Nova, 3/8” NPT
Gas Supply Pressure
Minimum
Normal
Natural Gas
5.5”
7”
Propane
11”
11”
Manifold Pressure
Natural Gas
Manifold Pressure High
3.5 IN. W.C./.87 KPa
Manifold Pressure Low
1.6 IN. W.C./.40 KPa
ZCV39LPH/LPHE
Propane
Millivolt / IPI
ZCV42N/NE
Natural
Millivolt / IPI
ZCV42LP/LPE
Propane
Millivolt / IPI
ZCV42NH/NHE
Natural
Millivolt / IPI
ZCV42LPH/LPHE
Propane
Millivolt / IPI
29,000 BTU
23,000 BTU
25,000 BTU
16,500 BTU
25,000 BTU
19,500 BTU
29,500 BTU
20,000 BTU
29,000 BTU
23,000 BTU
#51
#38
1/16”
#36
#51
Fully Open
1/16”
Fully Open
1/16”
Fully Open
Maximum
9”
12”
Propane
10 IN. W.C./2.61 KPa
6.3 IN. W.C./1.57 KPa
47
Millivolt System, Lighting, and Burner Control
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
A
B
BEFORE LIGHTING
This appliance has a pilot which must be lighted by hand. When

Immediately call your gas supplier from a neighbour’s phone. Follow the
lighting the pilot, follow these instructions exactly.
gas supplier’s instructions.
Smell all around the appliance area for gas. Be sure to smell next
to the floor because some gas is heavier than air and will settle on
the floor.

If you cannot reach your gas supplier, call the fire department.
C
Use only your hand to push or turn the gas control knob. Never use
tools. If the knob will not push in or turn by hand, don’t try to repair it.
Call a qualified technician. Force or attempted repair may result in a fire
or explosion.
D
Do not use the appliance if any part has been under water. Immediately
call a qualified service technician to inspect the appliance and to
replace any part of the control system which has been under water.
WHAT TO DO IF YOU SMELL GAS

Do not try to light an appliance.

Do not touch any electrical switch; do not use any phone in your
building.
1.
2.
3.
4.
5.
Stop! Read the safety information above this label.
Set the thermostat to lowest setting.
Turn off all electrical power to the appliance.
Locate valve under the burner assembly.
If the control knob is not already in the off position, i.e. the word
“OFF” in the 9 o’clock position, then push in the gas control knob
slightly and turn  clockwise to “OFF”. NOTE: Knob cannot be
turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do
not use force.
Wait five [5] minutes to clear out any gas. If you then smell gas.
STOP! Follow “B” in the safety information above on this label. If
you don’t smell gas then go to the next step.
Now push in the control knob slightly and turn  counter-clockwise
to the “PILOT” position.
Push in the control knob all the way and hold it. With the other
hand push in the red igniter button until you hear a click. Now
observe closely the pilot burner located on the rear center-left
hand side of the main burner.
LIGHTING INSTRUCTIONS
6.
7.
8.
If a flame has appeared then continue to depress the control knob for 20
seconds. If the flame did not appear then continue to depress the red
igniter button every 5 seconds until a flame is established. NOTE: If
after 30 seconds a flame has not yet been established then turn the
control knob back to the off position and repeat steps 5, 6 & 7.
9. Once the pilot has been established hold the control knob in the
depressed position for approximately 25 seconds before releasing. If
the flame goes out then repeat steps 7 and 8.
 If the knob does not pop up when released, stop and immediately call
your service technician or gas supplier.
 If the pilot will not stay lit after several tries, turn the gas control to
“OFF” and call your service technician.
10. Now turn the control knob to the “ON” position. The burner will not light
unless the wall switch thermostat or remote control is turned “ON” or in
the case of the thermostat there is a call for heat.
11. Close the access door and turn all electrical power back to the
appliance.
12. The pilot must be turned off when the unit is not in use.
TO TURN OFF THE APPLIANCE
1.
2.
3.
Set the thermostat to lowest setting.
Turn off all electric power to the appliance if service is to be
performed.
Open the control access door.
4.
5.
Push in the gas control knob slightly and turn  clockwise to the “OFF”
position. Do not force.
Replace control access panel.
NOTE: Only one on/off device (manual on/off, remote control, or hard wired thermostat) should be connected to the
appliance at any one time, this is most important when installing an insert or stove as the on/off rocker switch is installed at
the factory.
Recommended Maximum Lead Length (Double Wire)
When Using Wall Switch or Thermostat
Wire Size
Max. Length
14ga
100ft [30.4m]
16ga
64ft [19.5m]
18ga
40ft [12.1m]
20ga
25ft [7.6m]
22ga
15ft [4.5m]
To Wall Switch,
Thermostat*, Or
Remote Receiver
CAUTION: DO NOT WIRE 120V POWER TO
MILLIVOLT SWITCHES OR THERMOSTAT.
*In the U.S.A. Thermostats are not permitted for Vented Gas Fireplaces (ANSI Z21.50b-2009 -Decorative).
48
Troubleshooting the Gas Control System
WARNING
BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE THE GLASS FRONT. Before troubleshooting the
gas control system, be sure external gas shut off is in the "On" position.
Problem
Spark igniter will not light.
Possible Causes
Corrective Action
Defective or misaligned
electrode at pilot.
Check for spark at electrode and pilot: if no spark and electrode wire is
properly connected, replace igniter.
Defective igniter (pushbutton).
Using a match, light pilot. If pilot lights, turn off pilot and push the red button
again. If pilot will not light - check gap at electrode and pilot should be 1/8" to
1/4" to have a strong spark.
Defective thermocouple
(flame switch where
applicable).
Check pilot flame. Must impinge on generator and thermocouple. Clean
and/or adjust pilot for maximum flame impingement on generator and
thermocouple. Replace thermocouple if pilot will not hold. (Hand tight 1/8 turn
on replacement)
Defective valve magnet.
Replace valve, if pilot won't hold after the thermocouple is replaced.
Wall switch or wires
defective.
Check wall switch and wires for proper connections. Jumper wire across
terminals at wall switch. If burner comes on, replace defective wall switch. If
okay, jumper wires, across wall switch wires at valve. If burner comes on,
wires are faulty or connections are bad.
Generator may not be
generating sufficient voltage.
Check generator with millivolt meter. Take reading at generator terminals of
gas valve. Should read 325 millivolts minimum while holding valve knob
depressed in pilot position and wall switch "off" Replace faulty generator if
reading is below specified minimum.
Plugged burner orifice.
Check burner orifice for stoppage and remove.
Defective automatic valve
operator.
Remove wall switch wires from gas valve. Install jumper wires from top bottom
terminals of gas valve. Turn valve on "ON". If main burner does not light,
replace valve.
Frequent pilot outage
problem.
Pilot flame may be too low or
blowing (high) causing the
pilot safety to drop out.
Clean and/or adjust pilot flame for maximum flame impingement on generator
and thermocouple.
Flame lifts off burner and
goes out in less than 30
seconds.
The inner liner has come off
flue or termination, flame is
starving for oxygen.
Attach the inner liner to flue or termination using screws, silicone and clamps
as stated in manual.
Flame lifts off burner on
one side while the rest of
the flame remains lit.
Improper installation of
firebrick. Firebrick is likely
leaning.
Be sure to position firebrick against firebox walls and be sure to use brick clips
attached to the inner side of firebox.
Pilot will not stay lit after
carefully following lighting
instructions.
Pilot burning, no gas to
burner, valve knob “ON”,
and wall switch “ON”.
49
Burner System Maintenance
It is recommended to annually inspect and clean the Burner System to prevent malfunction and / or sooting. This
operation should be performed by your dealer or a qualified technician.
-CAUTIONBefore servicing the burner system ensure that the gas supply is turned OFF and disconnect all electrical connections to
the appliance. Allow the appliance to cool to room temperature. Note that the pilot assembly may be hot in an
intermittent or standing-pilot system—even if the main burner was never on. Exercise caution when working within the
area.
-ALL WORK SHOULD BE PERFORMED BY A QUALIFIED AND CERTIFIED TECHNICIANMonthly Flame Inspection
It is recommended to turn on the unit at least once a month and inspect the flame pattern to ensure there are no problems
with the burner tube. The pilot flame should also be inspected monthly to ensure proper operation.
Thermocouple / Flame Sense
Pilot Burner
Thermopile
Pilot must maintain this
relationship with Burner Tube.
Flame should appear similar to the above picture.
Conversion Kit Instructions – PART A
Description
Pilot Orifice
Burner Orifice
Brass (1000-255)
39ZCV-CKLP
42ZCV -CKLP
LP Conversion
-Millivolt-
1001-P167SI
#30 (977.167)
39ZCV-CKNG
42ZCV-CKNG
NG Conversion
-Millivolt-
39ZCV-CKLPI
42ZCV-CKLPI
Kit Number
Brass Nipple
Air Shutter
Hi/Lo Regulator
1/16”
1/16”
1000-253 closed
1000-253 closed
Fully Open
Fully Open
1001-P202SI
(0.907.202)
1001-P165SI
#51 (977.165)
#38
#38
1000-253 closed
1000-253 closed
1/16”
1/16”
1001-P201SI
(0.907.201)
LP Conversion
-IPI -
1001-P168SI
#35 (977.168)
1/16”
1/16”
1000-253 closed
1000-253 closed
Fully Open
Fully Open
1002-P014SI
(0.907.014)
39ZCV-CKNGI
42ZCV-CKNGI
NG Conversion
- IPI -
1001-P166SI
#62 (977.166)
#38
#38
1000-253 closed
1000-253 closed
1/16”
1/16”
1002-P016SI
(0.907.016)
39ZCV-CKLPH
42ZCV –CKLPH
LP Conversion
-Millivolt-
1001-P167SI
#30 (977.167)
#51
#51
1000-253 closed
1000-253 closed
Fully Open
Fully Open
1001-P202SI
(0.907.202)
39ZCV-CKNGH
42ZCV-CKNGH
NG Conversion
-Millivolt-
1001-P165SI
#51 (977.165)
#37
#36
1000-253 closed
1000-253 closed
1/16”
1/16”
1001-P201SI
(0.907.201)
39ZCV-CKLPHI
42ZCV-CKLPHI
LP Conversion
-IPI -
1001-P168SI
#35 (977.168)
#51
#51
1000-253 closed
1000-253 closed
Fully Open
Fully Open
1002-P014SI
(0.907.014)
39ZCV-CKNGHI
NG Conversion
1001-P166SI
#37
1000-253 closed
1/16”
1002-P016SI
#62 (977.166)
42ZCV-CKNGHI
- IPI #36
1000-253 closed
1/16”
(0.907.016)
Refer to “Gas Specifications Chart” for inlet pressures and input ratings. Clock meter to verify input rate. Place conversion label as close to
converted gas control as possible. Refer to lighting instructions to verify the normal operating sequence of the ignition system. IMPORTANT:
Always check for gas leaks with a soap and water solution. DO NOT USE OPEN FLAME FOR LEAK TESTING.
50
Gas Conversion Part A ZCV39 / ZCV42
IMPORTANT: Always check for gas leaks with a soap and water solution. DO NOT USE OPEN FLAME FOR LEAK TESTING.
Main Burner
Air Shutter & Screw
Pilot Orifice
Main Burner Orifice
Brass Nipple
Hi / Lo Regulator
1. The Main Burner must be removed from the Burner Pan
Assembly (See Burner Removal Section). Adjust the Air
Shutter to the correct Primary Air setting as specified in
the manual or on the label plate. To adjust the Primary
Air setting, loosen screw on the side of the Air Shutter
and rotate to the correct opening using a drill bit or tape
measure. Retighten screw.
2. Remove the Main Burner Orifice using a ½” wrench and
replace with the new Conversion Orifice which came with
the Conversion Kit.
3. Replace the Main Burner. Install the new Pilot Orifice (See
Pilot Conversion) and Hi/Lo valve regulator by following
instructions supplied with the Conversion Kit.
Pilot Must
Maintain This
Relationship
With Main
Burner.
Refer to “Gas Specifications Chart” for inlet pressures and input ratings. Clock meter to verify input rate. Place conversion label as
close to converted gas control as possible. Refer to lighting instructions to verify the normal operating sequence of the ignition system.
⚠-WarningThis conversion kit shall be installed by a qualified service agency in accordance with the
manufacturer's instructions and all applicable codes and requirements of the authority having
jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or
production of carbon monoxide may result causing property damage, personal injury or loss of
life. The qualified service agency is responsible for the proper installation of this kit. The
installation is not proper and complete until the operation of the converted appliance is checked
as specified in the manufacturer's instructions supplied with the kit.
⚠Caution:
The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion.
51
installationinstructions
DRAFT
A00
gas conversion kit for top
convertible pilot 3$57%series 0190XYZ)
Instructions for converting SIT 190 series pilot burner injector from NG to LPG and from LPG to NG only.
This information should be considered as supplemental to the Appliance Manufacturer's Instructions.
Warning!
The installation of this conversion kit must only be undertaken by a qualified and
certified gas appliance installer.
1
Shut-off the gas supply to the appliance.
2
Allow the pilot burner to cool to room temperature.
WARNING: Touching a hot pilot burner
can result in injury.
3
The pilot hood is held in place by spring.
First remove the spring, then remove the hood by
pulling it up from the pilot bracket (fig. 1).
4
Insert a 5/32" or 4 mm Allen wrench into the
hexagonal key-way of the injector (fig. 2), and
rotate it counter-clockwise until it is free of the
injector journal.
5
Verify that the new injector is proper for the
application. The injector size is stamped on the
side of the injector near the top. LPG injectors have
a groove machined around their circumference
near the top, while NG injectors do not have a
groove (fig. 4).
Refer to the Appliance Manufacturer’s instruction
sheet for the proper injector size.
6
Insert the Allen wrench into the end of the injector.
Then, insert the injector into injector journal, and
rotate the injector clockwise until a torque of 9 lbf
in (1.0 Nm) is achieved.
7
First replace the pilot hood by aligning the tab on
the base of the hood with the slot in the side of the
pilot journal, and push the hood down, onto the
pilot bracket (fig. 3). The hood must sit squarely on
the bracket for proper operation.
Then replace the spring by pushing it on his seat
(fig.3).
Check to insure that the hood is properly seated
onto the pilot bracket and that the spring is
properly inserted onto his seat.
8
fig. 1
fig. 2
fig. 3
Injectors
NG
LPG
Restore the gas supply to the appliance, and ignite
the pilot burner.
Verify proper ignition and operation.
fig. 4
Warning!
This conversion kit must only be applied as part of a conversion kit supplied by the
APPLIANCE MANUFACTURER for the specific appliance, and type of gas, being converted.
INSTALLER NOTICE. These instructions must be left with appliance.
SIT Group
w w w . s i t g r o u p . i t
52
Gas Conversion for Modulator – PART C
-WARNING!-
-WARNING!-
53
ZCV39 / ZCV42
Burner Removal
To remove grate, remove two [2] screws
from grate bar assembly.
To remove burner, remove four [4] screws
from burner. Slide burner to the left and lift
to remove.
-⚠ WARNINGTurn off Unit and allow to cool before
cleaning. Only a Qualified service technician
should service and repair this appliance.
ZCV39 / ZCV42
Burner System Removal / Installation
Removal: Remove Log Holder. Remove fourteen [14] screws around edge of Burner Pan. Carefully work the burner pan
loose & lift the assembly upward to remove it from the firebox cavity.
Installation is the reverse of these steps. Ensure that the mounting surface is clean. Use fresh Black Mill Pac to reseal
the burner pan.
-⚠ WARNINGTurn off Unit and allow to cool before
cleaning. Only a Qualified service technician
should service and repair this appliance.
Log Holder
Burner Pan
54
IPI Electronic Ignition System
Overview
The IPI system is an advanced burner controller that
provides you with the option of having either a StandingPilot, or an intermittent igniting system. This alternating
mode is controlled by the CPI/IPI Switch (Continuous Pilot
Ignition/Intermittent Pilot Ignition) located on the IPI System
Box. The difference between a Standing-Pilot and an
Intermittent-Pilot is in whether the pilot stays lit or shuts off:
In Standing-Pilot, the pilot assembly is lit by the IPI Main
Module and continues to stay lit until 1) the CPI/IPI Switch is
switched to the IPI position; 2) a loss of electrical power
(battery and AC source), 3) the flame sensor loses its signal,
4) the fuel supply discontinues, or 5) the IPI Main Module
malfunctions.
In the Intermittent-Pilot mode, the pilot shuts off when the
appliance is not in use. The advantage of this mode is that
fuel is not consumed when the fireplace is not operating.
NOTE: In some jurisdictions Intermittent-Pilot is required.
That means the pilot cannot remain lit when the appliance is
not operating.
Components
The core of the IPI system is the Main Module and the IPI
Valve. With these two components the system is able to
operate a gas fireplace. There are also other components
available to complement the IPI system.
UHS
Box
Cover
Backup
Battery
Pack
Remote
Receiver
Module
CPI / IPI
Switch
IPI Module
Fan Control Module
AC Adapter
Plug In
IPI System Cover: Is essential in keeping the components at
their proper operating temperatures. DO NOT OPERATE
THE APPLIANCE WITHOUT THIS COVER.
Modulating Servo Motor: Is an add-on valve component that permits HI/LO functionality to be controlled by the remote.
Contrary to this feature is a Manual HI/LO Control Knob. The Modulating Servo Motor requires the Remote system to be
present.
Backup Battery Pack: This component permits the IPI system to operate without the need for an external AC Adapter
power source. The advantage to using the battery backup is that in the case of a power failure, the appliance is still
operable.
NOTE: In certain instances the IPI Main Module requires resetting. This can occur if the system is unable to ignite the pilot
or the main burner in the allotted time period. The IPI is programmed to lockout all commands. To reset this lockout you
must deplete the system of all electrical power. This means to remove the batteries from the Battery Pack, remove the
batteries from the Remote Receiver (if applicable), and disconnect the AC Adapter from the system. Leave the power off
for approximately 25 seconds to clear its lockout.
Remote Receiver: This component provides the capability of controlling the appliance with a wireless remote transmitter.
Standing Pilot Mode for Colder Climates (Below Freezing)
For IPI models it may be necessary to set the appliance to Standing Pilot mode to maintain heat in the cavity. The purpose of this
procedure is to prevent cold air from penetrating the chimney and then onto the living space. Therefore, when the internal
temperature is slightly elevated the fireplace is able to freely exhaust its combustion and hence making it easier to startup.
55
-Remote Control OperationThe Proflame GTM is configured to control the on/off main burner operation, its flame levels, and provides on/off and
Smart thermostatic control of the appliance.
Transmitter
Transmitter
The Transmitter is powered by 3 AAA type batteries. A Mode
Key is provided to Index between the features and a
Thermostat Key is used to turn on/off or index through
thermostat functions
Remote Receiver
The Receiver connects directly to the gas valve and stepper
motor with a wiring harness. The Receiver is powered by 4 AA
type batteries. The Receiver three position slider switch can be
set to one of three positions: ON (Manual Override), Remote
(Remote control) or Off.
Initializing the System for the first time
Install 4 AA batteries into the receiver battery bay. Install 3
AAA type batteries in the Transmitter battery bay.
Place the 3 position slider switch in the “Remote” position.
Insert the end of a paper clip into the hole marked “PRG” on
the Receiver front cover. The Receiver will “beep” three (3)
times to indicate that it is ready to synchronize with a
Transmitter. Push the On button. The Receiver will “beep” four
times to indicate the Transmitter’s command is accepted. The
system is now initialized.
Temperature indication Display
With the system in the “OFF” position, press the Thermostat
Key and the Mode Key at the same time. Look at the LCD
screen on the Transmitter to verify that a C or F is visible to the
right of the Room Temperature display.
Turn the Appliance On or Off
Press the ON/OFF Key on the Transmitter
Remote Flame Control
The Proflame GTM has six (6) flame levels. Pressing the Down
Arrow Key once will reduce the flame height by one step until
the flame is turned off. The Up Arrow Key will increase the
flame height each time it is pressed. If the Up Arrow Key is
pressed while the system is on but the flame is off, the flame
will come on in the high
position.
NOTE: The Remote
Receiver module can also
be located outside of the
appliance to a maximum of
6ft away installed in a
certified deep wall switch
electrical box (2-3/4”
depth). For this
configuration an extension
wiring harness (P/N: 1001P904SI) is required.
Remote Receiver
Room Thermostat ( Transmitter Operation)
The Remote Control can operate as a room thermostat. To
activate this function, press the Thermostat Key. The LCD
display on the Transmitter will change to show that the room
thermostat is “ON” and the set temperature is now displayed.
To adjust the set temperature, press the Up or Down Arrow
Keys until the desired set temperature is displayed on the LCD
screen of the Transmitter.
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the flame height in
accordance to the difference between the set point
temperature and the actual room temperatures. As the room
temperature gets closer to the set point the Smart Function will
modulate the flame down. To activate this function, press the
Thermostat Key until the word "SMART" appears to the right of
the temperature bulb graphic. To adjust the set temperature,
press the Up or Down arrow Keys until the desired set point
temperature is displayed.
Key Lock Function
This function will lock the keys to avoid unsupervised
operation. To activate this function, press the MODE and the
UP Arrow Key at the same time. To de-activate this function,
press the MODE and the UP Arrow Key at the same time.
Low Battery Detection
Transmitter - When the Transmitter batteries are low, a
Battery Icon will appear on the LCD display of the Transmitter.
Receiver - When the Receiver batteries are low, No “beep” will
be emitted from the Receiver when it receives an On/Off
command from the Transmitter. When the batteries are
replaced the “beep” will be emitted from the Receiver when the
ON/OFF Key is pressed (See Initializing the System for the first
time).
Manual Bypass Of The Remote System
If the batteries of the Receiver or Transmitter are low or
depleted, the appliance can be turned on manually by sliding
the three position slider switch on the Receiver to the ON
position. This will bypass the remote control feature and the
appliance main burner will come on if the gas valve is in the
“On” position.
*In the U.S.A. Thermostats are not permitted for Vented
Gas Fireplaces (ANSI Z21.50b-2009 -Decorative).,
56
IPI Electronic Ignition Parts List – Standard System
ITEM NO.
PART NO.
DESCRIPTION
1
1006-P002si
Valve IPI Hi/Lo NG
1006-P003si
Valve IPI Hi/Lo LP
2
*1002-P047si
Pilot Assembly-LP -24” Wire
*1002-P033si
Pilot Assembly-NG -24” Wire
3
1002-P017si
Spark Electrode (with wire)
*1002-P119si
Spark Electrode (with wire- 35” Length)
4
1002-P903si
Electrode Flame Sensor
*1002-P910si
Electrode Flame Sensor (35” Length)
5
1002-P302si
IPI Ignition Board
6
1002-P850si
AC Wall Adapter
7
1002-P12BH
Battery Pack
8
1002-P912si
Wiring Harness
9
1001-P166si
Orifice Pilot -NG#62
1001-P168si
Orifice Pilot -LP#35
10
1002-P013si
Stepper Motor -NG
1002-P012si
Stepper Motor -LP
1002-P016si
Hi/Lo Regulator -NG
1002-P014si
Hi/Lo Regulator -LP
*Models ZRB46E / MQRB4436E / MQRB5143E / MQRB6961E
Longer (35”) Wire length is required for these units.
Proflame System
Configuration: Manual Hi/Low
Simplified Wire Diagram
0.886.002
-OR0.886.003
57
Configuration #1: Basic manual HI/LO and manual ON/OFF capabilities.
58
Receiver Module
.584.523/521/221
1001-P221SI
Receiver Module
.584.523/521/221
1001-P221SI
59
Operating the Receiver Without Batteries For GT / EGT / GTM / EGTM Remote Controls
-Wiring Harness P/N 1002-P906si required for both IPI & Millivolt systems.
-Millivolt Systems will also require Power Adapter P/N 1002-P850si.
The Remote Receiver & IPI or Millivolt system can be powered by the AC Adapter. This is advantageous if you do not
want to use batteries. Simply connect the AC Adapter into the Remote Control Wiring Harness as per the diagrams below.
IPI System EGTM
Receiver Module
0.584.523/521/221
1001-P221SI
Millivolt System GTM
Receiver Module
0.584.523/521/221
1001-P221SI
*In the U.S.A. Thermostats are not permitted for Vented
Gas Fireplaces (ANSI Z21.50b-2009 -Decorative).
60
Configuration #3: Remote ON/OFF, variable HI/LO, and fan capabilities. Refer to the fan installation/removal section for fan
installation.
61
Electronic Ignition Lighting Instructions
If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or
loss of life.
Always light the pilot whether for the first time or if the gas supply has ran out with the glass door opened or removed.
FOR YOUR SAFETY READ BEFORE LIGHTING:
A. This fireplace is equipped with an ignition device which automatically lights the pilot. Do not try to light by hand.
B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than
air and will settle on the floor.
C. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect
the fireplace and replace any part of the control system and any gas control which has been under water.
•
•
•
•
WHAT TO DO IF YOU SMELL GAS:
Turn off all gas to the fireplace.
• Immediately call your gas supplier from a
Open windows.
neighbor's phone. Follow the gas supplier's
Do not try to light any appliance.
instructions.
Do not touch any electric switch; do not use any
• If you cannot reach your gas supplier, call
phone in your building.
the fire department.
LIGHTING INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Stop! Read the above safety information on this label.
Remove batteries from receiver, and/or Battery Backup Pack.
Turn off all electric power to the fireplace.
This fireplace is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by
hand.
Open the glass door.
to off (Located behind the access panel).
6. Turn manual shutoff valve clockwise
Wait five (5) minutes to clear out any gas. If you smell gas including near the floor, STOP! Follow “B” in the above
safety information on this label. If you don’t smell gas go to the next step.
to on.
Turn manual shutoff valve counter-clockwise
Close the glass door.
Turn on all electric power to the fireplace and re-install batteries into the Transmitter/Receiver, and/or Battery
Backup Pack.
Turn “On” Switch that operates the Main Burner. If using a Remote Control refer to Remote Control Operation
Manual for activation.
TO TURN OFF GAS
1. Turn off all electric power to the fireplace if service is to be performed, including removing batteries from Remote
Transmitter/Receiver and/or Battery Backup Pack.
2. Access door inside the firebox must be removed to access the manual shutoff valve.
3. If alternate shut-off valve was installed it can be shutoff instead of going through the fireplace to access the
fireplace shut off valve.
62
Vent Termination
Measure to the edge of the termination plate.
Measure to the edge of the round termination.
V
Vent Terminal
Air Supply
Area Where Terminal Not Permitted.
A - Clearance above grade, veranda, porch, deck, or balcony 12
inches (30cm) minimum.1-2
B - Clearance to window or door that may be opened. 12 inches (30cm)
minimum for appliances 100 000 Btuh (30 kW) and lower, in Canada.
9 inches2 (23cm) for appliances 50 000 Btuh and lower, in USA.
C - Clearance to permanently closed window minimum 12 inches
(30cm) recommended to prevent condensation on window, in
Canada. 9 inches2 (23cm) for appliances 50 000 Btuh and
lower, in USA.
D - Vertical clearance to ventilated soffit located above the termination within a horizontal distance of 2 feet (60cm) from the center
line of the termination. 18 inches (46cm) minimum.5
E - Clearance to unventilated soffit 12 inches (30cm) minimum.
F - Clearance under veranda, porch, deck or balcony 12 inches1
(30cm) minimum.4 US5
G - Clearance from a perpendicular inside wall or outer corner to
the edge of the vent terminal plate is 3” (minimum).
H - Clearance to each side of center line extended above
meter/regulator assembly 3 feet (91cm) within a height 15
feet (4.5m) above the meter/regulator assembly.
I - Clearance to service regulator vent outlet 3 feet (91cm)
minimum.1 US5
J - Clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other appliance: In Canada, 6 inches (15cm) for appliances ≤10,000 Btuh (3kW), 12 inches1
(30cm) minimum for appliances >10,000 Btuh (3kW) and
≤100,000 Btuh (30kW), 36 inches (91cm) for appliances
>100,000 Btuh (30kW). In the USA, 6 inches2 (15cm) for appliances ≤10,000 Btuh (3kW), 9 inches (23cm) for appliances
>10,000 Btuh (3kW) and ≤50,000 Btuh (15kW), 12 inches
(30cm) for appliances >50,000 Btuh (15kW).
K - Clearance to a mechanical air supply inlet 6 feet (1.8m) minimum.1,in Canada. In USA, 3 feet (91cm) above if within 10
feet2 (3m) horizontally.
L - Clearance above paved sidewalk or a paved driveway located
on public property 7 feet (2.1m) minimum.3
M - Clearance above highest point of exit on roof 18 inches
(45cm).
WARNING: WHEN THE
HORIZONTAL VENT
TERMINATION IS
ACCESSIBLE A
CERTIFIED GUARD
(SAFETY CAGE) SHALL
BE INSTALLED.
N - Clearance to perpendicular wall 24 inches (60 cm).
(Recommended to prevent re-circulation of exhaust products.
For additional requirements check local codes.)
NOTE: Clearances are to the edge of terminal plate, add 63/4” to clearances to arrive at center line.
NOTE: Local Codes or Regulations may require different
clearances.
Termination
It is imperative that the vent termination be located observing the
minimum clearances as shown. There must not be any obstruction such as bushes, garden sheds, fences, decks or utility buildings within 24” from the front of the termination plate.
Do not locate termination where excessive snow or ice build-up
may occur. Be sure to check vent termination area after snow
falls and clear to prevent accidental blockage of venting system.
When using snow blowers, make sure snow is not directed
towards vent termination area.
General Venting Information
The gas fireplace is approved to be vented either through the
side wall or vertically through the roof.
This appliance is approved with Kingsman flex vent system.
ONLY VENTING COMPONENTS SPECIFICALLY APPROVED
AND LABELED FOR THIS FIREPLACE MAY BE USED.
Venting terminal shall not be recessed into a wall or siding. If finishing the outside wall with vinyl or wood siding it is recommended that a Siding Shield be installed, Part Number ZDVSSLR.
1 - In accordance with the current CSA B149.1, Natural Gas
and Propane Code.
2 - In accordance with the current ANSI Z223.1/NFPA 54,
National Fuel Gas Code.
3 - A vent shall not terminate directly above a sidewalk or
paved driveway that is located between two single family
dwellings and serves both dwellings.
4 - Permitted only if veranda, porch, deck, or balcony is fully
open on a minimum of two sides beneath the floor.
5 - Clearance in accordance with local installation codes and
the requirements of the gas supplier.
63
General Vent Installation Information
This gas appliance is approved to be vented either through the side wall or vertically through the roof. Only Kingsman Flex (Z-Flex) Venting Kits and
components specifically approved and LABELED for this stove may be used. This appliance is also approved for use with Simpson-Duravent Direct Vent
system (Model DV-GS Series), BDM Pro Form Direct Vent, Ameri-Vent Direct Vent Pipe System, ICC Excel Direct, Metal Fab Sure-Seal DV and Selkirk
Direct Temp.
RIGID OR HARD PIPE
When using Simpson Duravent, Ameri-Vent pipe, BDM Pro Form Direct Vent, ICC Excel Direct,
Metal Fab Sure-Seal DV and or Selkirk Direct Temp a Duravent hard pipe adapter must be
used (part # ZDVDFA for fire- places and part # ZDVDKA for Stoves, Serenity and ZDV3624B).
Follow installation instructions provided by Simpson Duravent/Ameri-Vent/Selkirk Direct Temp,
ICC Excel Direct, and Metal Fab Sure-Seal DV for installation of pipe and adhere to the
clearance to combustibles provided in this manual. Apply a bead of Mill Pac high temp sealant
to all joints of pipes, adapters and termination, when using Kingsman Flex (Z-Flex) venting and
Simpson Duravent venting.
NOTE: Increase framing depth by one inch when using hard pipe.
FLEX PIPE VENTING
Kingsman Flex pipe is shipped in unexpanded length. When installing pipe expand the lengths.
Pipe can be expanded to twice their lengths e.g. 4ft. to 8ft. Fully expand pipe and cut off excess.
Do not use more than 2 couplers to extend short pipes. Single sections are preferred in an
installation attaching at the fireplace and termination.
Place the spring spaces provided approximately every two feet to stabilize 4” flex in the center
of 7” flex. When forming bends place spring in bend or before and after. (See Fig. 1). Horizontal
runs require support metal straps every 2 feet. In offset installation support straps should be
used to stabilize pipe.
Expand 4” and 7” flex pipe to the point that the 7” protrudes approximately 2 to 3 inches past
outer wall and the 4” flex protrudes approximately 2 to 3 inches past the 7” flex. (See Fig. 1).
Attach the 4” pipe to the termination first and secure with sealant and screws then attach the 7”
flex to the termination with caulking and screws. Termination may then be moved back to the
outer wall and attached to home screwing into the framing. Silicone around termination to
waterproof. If siding shield is going to be used attach this using same attaching hole as the top
of termination after termination has been caulked for water proofing.
Use Hi Temp Sealant
Apply a bead of Mill Pac high temp sealant to all joints and use four screws to secure each
pipe at fireplace, termination and any joint if joining any sections of pipe.
FRAMING DIMENSION
Combustible Wall
Cut an 11” hole through exterior wall and frame as
shown below.
Non Combustible Wall
Cut or drill 8” or 204mm diameter hole.
NOTE: It is critical to the proper and safe operation of
this fireplace that on all connections the inner liner and
the outer casing are both caulked with liberal amounts
of sealant. Do not use any kind of tape or silicone other
than that recommended in this manual, Mill Pac Sealant
⚠ WARNING: DO NOT mix parts from different systems unless stated in the manual.
Installation of Side Wall Venting
1.
To determine the minimum distance from the bottom of fireplace to center of
FLUE GAS OUTLET
vent see the Framing Your Gas Fireplace section. Cut a hole through the
COMBUSTIBLE AIR INLET
wall allowing for an 11” x 11” (inside diameter) in combustible walls for wall
thimble or an 8” diameter hole in a non-combustible wall (See Figure 2).
2. For the clearance to combustible above a 90 degree bend see Clearance to
Combustibles section.
MINIMUM 1” TO
3. Select the approximate vent length, precise measurements are not needed as
COMBUSTIBLES
your flex pipe can be expanded to twice its shipped length for ease of
installation
4. To install wall thimble center over 11” x 11” (inch) framing from both sides of
wall and secure. Route flex vent pipe through wall thimble (See Figure 1).
MIN 48” FOR ZCV39N, 60” FOR LP
5. Before joining pipes, apply a bead of high temperature sealant (Mill Pac) to
MIN 52-1/2” FOR ZCV42N, + 64-1/2” FOR LP
end of pipe. First attach the four inch (4”) flue pipe to the vent termination with
sealant, and secure with the four screws provided. At this time make sure the
spacer springs are attached to the (4”) flex pipe as required. Then attach the
FIGURE 1
seven inch (7”) pipe by the same method.
FRAMING DETAIL
6. Mount vent termination and seal to wall using caulking around the wall thimble
8” DIA
to weather proof. After installing the vent termination, double check to make
sure the pipe extends properly through wall thimble and into vent termination.
11”
7. Before joining pipes to fireplace flue, apply a bead of high temperature sealant
(Mill Pac) to end of pipe. First attach the four inch (4”) flue pipe to fireplace
with sealant, and secure with the four screws provided. At this time verify that
MIN 48” FOR ZCV39N, 60” FOR LP
the spacer springs are attached properly to the (4”) flex pipe as required. Then
11”
MIN 52-1/2” FOR ZCV42N, + 64-1/2” FOR LP
attach the seven inch (7”) pipe by the same method.
8. Support horizontal pipes every two (2) feet (61 cm) with metal strap bands.
Re-check fireplace to make sure it is levelled and properly positioned and
secured.
THROUGH NONTHROUGH
9. Support vertical pipes to maintain a minimum of 1” or greater clearance to
COMBUSTIBLE WALL
COMBUSTIBLE WALL
combustibles with metal strapping bands.
10. If finishing the outside wall with vinyl or wood siding it is recommended that a
FIGURE 2
Siding Shield be installed, Part Number ZDVSSLR.
WARNING:
WHEN
THE
HORIZONTAL
VENT
Note: Vent Termination must not be recessed into wall or siding.
TERMINATION IS ACCESSIBLE A CERTIFIED
GUARD (SAFETY CAGE) SHALL BE INSTALLED.
64
Venting Routes And Components
Venting Routes and Components
Since it is very important that the vent system maintain its
balance between the combustion air intake and the flue gas
exhaust, certain limitations as to vent configurations apply and
must be strictly adhered to.
The table showing the relationship between vertical and
horizontal side wall venting will help to determine the various
vent lengths.
The maximum horizontal run is 20 ft/6.1 m when the vertical
run is 7 ft/2.1m (Figure #2). Note: 1/4” vertical rise is required
for every 12” of horizontal run.
The maximum number of 45 degree bends per side wall
installation is two (2) in the horizontal run and then you must
reduce the length of the horizontal by 18 inches for each 45
degree bend.
The maximum vertical run is 43 ft./13.1meters.
Special Note: For each 45 degree bend installed in the
horizontal run, the length of the horizontal run must be reduced
by 18” (45cm). This does not apply if the 45 degree bends are
installed on the vertical part of the vent system.
Example: If according to the table, the length of the horizontal
run is 10 feet, and two 45 degree bends are required, the
horizontal run length must be reduced to 7 feet.
2 additional 90° bends or equals are allowed. The horizontal
run must be reduced by 36” per each 90° bend, or 18” per
each 45° bend.
IMPORTANT: Always locate the fireplace in such a
way that a minimum of offsets and/or horizontal runs
are required. 1/4” vertical rise is required for every 12”
horizontal run.
12 FEET
Figure 1
6 FEET
Plus ¼” Rise/Ft = 73-1/2”
20 FEET
MAX
Figure 2
Support Straps
Every 2 Feet
7 FEET
How to Use the Horizontal Vent Table
1. Determine the height of the system and the number of
bends required.
2. Having determined the vertical distance determine the maximum horizontal section allowed.
3. Vent table has been established for 90˚ horizontal/vertical
runs. With use of flex pipe distance not having 90˚ bends will
not fall into vent table standards. See Fig. B.
-Horizontal Venting Table from Bottom of FireplaceFor venting to a maximum of 43ft (13.1 meters).
Total Vertical
Max Total Horizontal
Feet
Meters
Feet
Meters
48” (ZCV39N)
1.2
5
1.5
52-1/2” (ZCV42N)
1.3
5
1.5
60” (ZCV39LP)
1.5
8
2.4
64-1/2” (ZCV42LP)
1.6
8
2.4
6
1.8
12
3.7
7
2.1
20
6.1
8
2.4
20
6.1
9
1.8
20
6.1
10
3.0
20
6.1
11
3.4
20
6.1
12
3.7
20
6.1
13
4.0
20
6.1
14
4.3
20
6.1
15
4.6
20
6.1
20
6.1
20
6.1
25
7.6
15
4.6
30
9.1
10
3.0
43 (Max)
13.1
0
0
Example A:
If the vertical dimension from
the floor of the fire- place is
6ft, the horizontal run to the
wall flange of the vent
termination must not exceed
12ft.
NOTE: The final location
of the fireplace must be
such that the horizontal
vent dimensions fall within those stated on the
graph. The Maximum
Vertical vent run is 43ft.
(13.1 meters).
12 FEET MAX
Important: Minimum
clearance between vent
pipes and combustible
materials is1 inch (25mm).
For Propane Horizontal installations
the venting must be an additional
one foot above the minimum vertical
rise off the flue before going
horizontal.
65
Z47ST24 / Z47ST36
Horizontal Snorkel Terminations
Two snorkel terminations are available if a vertical rise is necessary on the exterior side of a building:
Z47ST24 (24” Tall, 14-1/2” Center to Center)
Z47ST36 (36” Tall, 26-1/2” Center to Center)
Follow standard horizontal venting installation procedures. If the Snorkel Termination is to be located below grade, a
window well is recommended with adequate and proper drainage as per local codes. Leave 2” clearance below snorkel to
prevent water from entering the Snorkel Termination. Do not enclose the Snorkel within a wall or other type of enclosure
and do not back fill. Ensure that grade level slopes away from the building. Follow all local codes.
Maintain All Clearances,
including proper rise and run.
Ensure adequate drainage.
-FOLLOW ALL LOCAL CODES A safety cage (Z57STSC) is also available.
Place safety cage over snorkel and mount with [4] DT screws (supplied with safety cage).
66
Venting Straight Up Through Roof
An Attic Insulation Shield must be installed where the vent passes from a lower living space into an attic space where the chimney is
not enclosed. It is designed to keep insulation materials away from the chimney.
When installing the Attic Insulation Shield where the chimney passes from a living space to an attic space, install the shield from below
and nail in place using 1" spiral nails.
A fire stop must be installed on the bottom side of the joists when passing through a ceiling or floor. If an attic insulation shield is to be
used, a fire stop is not required.
Fire Stop
Attic Insulation Shield
Using Flex Bends
Avoid cutting joists by offsetting the flex pipe.
When using 45° bends a bend support is required directly above the highest bend.
When installing a bend in a joist area a minimum of 4" clearance to combustible to the top of bend must be maintained, sides and
bottom of pipe, a 1" clearance to combustibles must be maintained. If running horizontal through an area a 1-1/2" minimum clearance to
the top of the horizontal pipe must be maintained.
Maximum vertical height of system should not exceed 43 feet.
Use roof support and rigid pipe at roof level. Flex pipe is not permitted within roof support.
When penetrating the roof a rigid galvanized pipe must be used. Attach flex pipe to the rigid pipe with high temperature sealant, secure
with four screws assuring the flex pipe and rigid pipe are secured. Attach rigid pipe to termination with sealant and screw with 4 sheet
metal screws. The Inner flex pipe must be secured with 4 screws which must penetrate both the flex pipe and inner section of
termination. Attach 7” rigid pipe to 7” termination with sealant and screw with 4 sheet metal screws.
Vertical termination clearance is 18" [45.7cm] above the roof, measured from highest point of exit on the roof line.
Support vertical pipes to maintain minimum of one inch or greater clearances to combustibles.
Roof Flashing
Ensure that you have the proper roof flashing by checking your roof pitch using a level and two rulers, or by using a roof pitch card.
Slide a Roof Flashing suitable to your roof slope over the vent. Place the edge of the flashing plate that will be on the higher part of the
roof slope under the shingles. Both the sides and the lower edge lay on top of the shingles.
NOTE: At the top edge of the flashing plate, lift the shingles and nail the plate to the roof deck, then cement the shingles to
the plate with a suitable waterproof mastic.
Ensure that the chimney is plumb. Square up the flashing plate and nail in place to the roof deck. Use 12 nails with neoprene washers
or cover the heads with a suitable waterproof mastic. Wrap the storm collar around the vent above the flashing. Secure the ends
together loosely with nut and bolt supplied. Slide the collar down the vent until it comes in contact with the flashing. Tighten the bolt and
seal the Storm Collar to the vent with a suitable waterproof non-combustible mastic.
The flashing and storm collar should be painted to match the roof shingles. This will extend its life and improve the appearance. Clean,
prime and paint with suitable painting products.
Vertical Venting in Cold Climates
In cold climate conditions where temperatures go below -10 degrees Celsius or 14 degrees Fahrenheit, we recommend that the chase
be insulated and where the vent pipe enters into the attic space that the pipe be wrapped with an insulated Mylar sleeve. This will
increase the temperature of the vent and help the appliance to vent properly in cold weather conditions.
It is also important in vertical vented direct vent appliances that the appliance be operated daily during the winter months as this will
help stop the termination from freezing up.
We recommend using a thermostat set at room temperature to allow the unit to cycle.
For IPI models it may be necessary to set the appliance to Standing Pilot mode to maintain heat in the cavity. The purpose of this
procedure is to prevent cold air from penetrating the chimney and then onto the living space. Therefore, when the internal temperature
is slightly elevated the fireplace is able to freely exhaust its combustion and hence making it easier to start up.
-ALSO SEE DIAGRAMS ON FOLLOWING PAGE-
67
-RestrictorRemove for Runs
Under 15 Feet
Clearances in horizontal venting.
FDVVT40
43ft
Straight-through roof support configuration; b) Flex bend configuration; c) Termination mounting
68
58PVH-Dimensions
12-1/2"
13"
1-1/2"
1/2"
10-5/8"
11"
13"
10-5/8"
5"
8-1/8"
1-1/4"
16"
13"
8-1/8"
5"
11"
11-1/8"
11"
11-3/8"
69
PVH58
INSTALLATION OVERVIEW
The PVH58 Horizontal Power Vent is approved for the following models only:
MQRB4436, MQRB5143, MQRB6961, ZRB46, ZCV39, ZCV42
Either Hard Pipe or Flex Pipe can be used, along with the appropriate adapter kit.
The Following Steps Are Required To Install The PVH58 Horizontal Power Vent:
 Install fireplace as per manual instructions.
 Choose suitable location for PVH58 Power Vent Termination. Refer to Termination Installation and
PVH58 Venting Clearances sections of this manual.
 Determine venting configuration to be used (i.e. hard pipe or flex, and routing). Install venting with
appropriate adapter kits. See PVH58 Venting – Hard Pipe or Flex, and PVH58 Venting
Configurations sections of this manual.
 Install PVH58 Wall Thimble if mounting in a combustible wall (PVH58 Wall Thimble Installation
section).
 Install PVH58 Power Vent (PVH58 Power Vent Mounting section).
 Electrical connections (PVH58 Wiring Harness Connections and Millivolt / IPI System
Connections sections).
 Air Intake Adjustment & Troubleshooting (refer to these sections).
PVH58
TERMINATION INSTALLATION
Termination Clearances
It is imperative that the vent termination be located observing the minimum clearances as shown.
There must not be any obstruction such as bushes, garden sheds, fences, decks or utility buildings
within 24" from the front of the termination plate. Do not locate termination where excessive snow or
ice build-up may occur. Be sure to check vent termination area after snow falls and clear to prevent
accidental blockage of venting system. When using snow blowers, make sure snow is not directed
towards vent termination area. Venting terminal shall not be recessed into a wall or siding, except for
mounting flange. ALSO REFER TO PVH58 VENTING CLEARANCES SECTION.
Mounting Flange
Mounting Flange
MINIMUM CLEARANCE ABOVE A
COMBUSTIBLE SURFACE IS 27”.
FOLLOW ALL LOCAL CODES
MINIMUM CLEARANCE ABOVE
GRADE OR A NONCOMBUSTIBLE SURFACE IS 12”.
70
PVH58
VENTING CLEARANCES
Note: Clearances are to the edge of terminal plate, add 5-1/2" to
clearances to arrive at center line.
Note: Local Codes or Regulations may require different clearances.
A. Clearance above a veranda, porch, deck, or balcony or other combustible surface is 27”. Clearance above grade is12in [30cm]
min.[1,2].
B. Clearance to window or door that may be opened. 12in [30cm] min. for appliances 100,000BTUh [30kW] and lower, in Canada. 9in[2]
[23cm] for appliances 50,000 BTUh and lower, in USA.
C. Clearance to permanently closed window min. 12in [30cm] recommended to prevent condensation on window, in Canada. 9in[2]
[23cm] for appliances 50,000 BTUh and lower, in USA.
D. Vertical clearance to ventilated soffit located above the termination within a horizontal distance of 2ft [60cm] from the center line of
the termination. 18in [46cm] min.[4]
E. Clearance to unventilated soffit 12in [30cm] min.
F. Clearance under veranda, porch, deck or balcony 12in [30cm] min.[3] (US[4])
G. Clearance from a perpendicular inside wall or outer corner to the edge of the vent terminal plate is 3in [7.6cm] min.
H. Clearance to each side of center line extended above meter/regulator assembly 3ft [91cm] within a height 15ft [4.5m] above the
meter/regulator assembly.
I. Clearance to service regulator vent outlet 3ft [91cm] min.[1] (US[4])
J. Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance: In Canada, 6in [15cm] for
appliances ≤10,000 BTUh [3kW], 12in[1] [30cm] minimum for BTUh [30kW], 36in [91cm] for appliances >100,000 BTUh [30kW]. In the
USA, 6in[2] [15cm] for appliances ≤10,000 BTUh [3kW], 9in [23cm] for appliances >10,000 BTUh [3kW] and ≤50,000 BTUh [15kW],
12in [30cm] for appliances >50,000 BTUh [15kW].
K. Clearance to a mechanical air supply inlet 6ft [1.8m] min.[1] in Canada. In USA, 3ft [91cm] above if within 10ft[2] [3m] horizontally.
L. Clearance above paved sidewalk or a paved driveway located on public property 7ft [2.1m] min.[5]
M. Clearance above highest point of exit on roof 18in [45cm].
N. Clearance to perpendicular wall 24in [60cm]. (Recommended to prevent re-circulation of exhaust products. For additional
requirements check local codes.)
O. A moisture-exhaust duct shall not terminate within 3 ft (1 m) in any direction of a service regulator or fresh-air intake.
1.
2.
3.
4.
5.
In accordance with the current CSA B149.1, Natural Gas and Propane Code.
In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code.
Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
Clearance in accordance with local installation codes and the requirements of the gas supplier.
A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both
dwellings.
71
PVH58 VENTING
HARD PIPE OR FLEX
Approved For 4/6-5/8”, 5/8” Hard Pipe
The PVH-58 Power Vent is approved for use with DuraVent-DirectVent Pro Direct Vent system (Model DV-GS Series),
and AmeriVent Direct Vent Pipe System, ICC Excel Direct, Metal Fab Sure-Seal DV and Selkirk Direct Temp. Follow
installation instructions provided by the appropriate manufacturer for installation of pipe, and adhere to the clearance to
combustibles provided in this manual. Apply a bead of Mill Pac high temp sealant to all joints of pipes, adapters and
termination as recommended.
WARNING: DO NOT mix parts from different systems unless stated in the manual.
ADAPTERS REQUIRED FOR HARD PIPE INSTALLATION
(ADAPTERS REQUIRED AT FIREPLACE)
FIREPLACE
ADAPTER
KIT
REQUIRED
ZRB46
ZCV39, ZCV42
MQRB4436
MQRB5143
MQRB6961
(4/7” Venting)
(4/7” Venting)
(5/7” Venting)
(5/7” Venting)
(7/10” Venting)
ZDVDKA
Duravent Fireplace
Adapter
*See Note*
ZDVDFA
Duravent
Fireplace Adapter
*See Note*
Z57DFA
Hard Pipe
Adapter
Z57DFA
Hard Pipe
Adapter
Z69DFA- Kit
Pipe Reducer 10”Lg – 8”Sm
Pipe Reducer 7”Lg – 5”Sm
*NOTE: For 4 x 6-5/8” venting on ZRB46, ZCV39 & ZCV42, a ZDVDIA Duravent Pipe Increaser will be required to
connect to 5/8” hard pipe section at power vent.
ZDVDKA
ZRB46 at fireplace
ZDVDFA
ZCV39, ZCV42 at fireplace
*ZDVDIA
ZRB46, ZCV39/42 at termination
Z57DFA
Z69DFA
MQRB4436, MQRB5143
MQRB6961
72
Approved For 4/7”, 5/7” And 7/10” Kingsman Flex (Z-Flex) Pipe
Flex Pipe Venting
Kingsman Flex pipe is shipped in unexpanded length. When installing pipe expand the lengths. Pipe can be expanded to
twice their lengths e.g. 4ft. to 8ft. Fully expand pipe and cut off excess.
Be sure to use approved couplers and connectors to join flex pipe.
Place the spring spaces provided approximately every two feet to stabilize inner flex in the center of the outer flex. When
forming bends place spring in bend or before and after. Horizontal runs require support metal straps every 2 feet. In off set
installation support straps should be used to stabilize pipe.
Expand inner and outer flex pipe to the point that the inner flex protrudes approximately 2 to 3 inches past the outer flex.
Attach the inner flex to the adapter first and secure with sealant and screws then attach the outer flex to the adapter with
caulking and screws. Silicone around termination to waterproof.
Use Hi Temp Sealant
Apply a bead of mill pac high temp sealant to all joints and use four screws to secure each pipe at fireplace, termination
and any joint if joining any sections of pipe.
ONLY VENTING COMPONENTS SPECIFICALLY APPROVED AND LABELED FOR YOUR FIREPLACE MAY BE USED.
ADAPTERS REQUIRED FOR FLEX PIPE INSTALLATION
(ADAPTERS REQUIRED AT POWER VENT)
ONE 12” SECTION OF 5/8” HARD PIPE MUST BE CONNECTED DIRECTLY TO THE POWER VENT BEFORE
ANY ADAPTERS ARE CONNECTED.
FIREPLACE
ADAPTER KIT
REQUIRED
ZRB46
ZCV39, ZCV42
(4/7” Venting)
(4/7” Venting)
MQRB4436
(5/7” Venting)
MQRB5143
(5/7” Venting)
MQRB6961
(7/10” Venting)
Z47PVA
Z47PVA
Z57PVA
Z57PVA
Z69PVA
Pipe Reducers
8”Sm – 7”Sm
5”Sm – 4”Sm
*See Note*
Pipe Reducers
8”Sm – 7”Sm
5”Sm – 4”Sm
*See Note*
Pipe Reducer
8”Sm – 7”Sm
ZDV5FC
Pipe Reducer
8”Sm – 7”Sm
ZDV5FC
Pipe Reducers
10”Sm– 8”Sm
7”Sm – 5”Sm
*NOTE: For 4 x 6-5/8” venting on ZRB46, ZCV39 & ZCV42, a ZDVDIA Duravent Pipe Increaser will be required to
connect to 5/8” hard pipe section at power vent.
Z47PVA
ZRB46
Z57PVA
MQRB4436, MQRB5143
Z69PVA
MQRB6961
73
PVH58
VENTING CONFIGURATIONS
Refer to Air Intake Adjustment
section of this manual to adjust Air
Intake Shutter.
PVH-58
Maximum / Minimum Vent Lengths:
Maximum Vent Length is 125 ft plus six 90° elbows with Air Intake
Shutter fully closed. Termination must not be below unit.
This power vent can be installed up to 3ft below the installed fireplace
on runs less than 100ft and not more than four 90° elbows.
Minimum Vent Length is 3ft horizontal plus minimum vertical rise with
Air Intake Shutter fully open.
MIN Venting= 3ft horizontal plus
minimum vertical rise with Air
Intake Shutter fully open
MAX Venting = 125ft
plus six 90° elbows
MAX 3ft Below Unit
 Refer to fireplace manual for proper installation of your fireplace.
 Minimum clearance to combustibles on venting is 1” unless otherwise stated in manual.
 Refer to your fireplace manual for venting clearances up to 30 feet.
 After 30ft of venting, clearance to combustibles is 1”.
PVH58 - Minimum Vertical Rise Before First 90° Elbow
(Measured from bottom of appliance to center of vent pipe)
ZRB46
MQRB4436
MQRB5143
MQRB6961
ZCV39
ZCV42
Seven 90° elbows are possible if
the total horizontal is not more than
25ft and the vertical does not
exceed 15ft.
None Required
37-1/2"
51-1/2”
56-1/2”
48”
52-1/2”
NOTE: MODELS EQUIPPPED WITH
MILLIVOLT/ STANDING PILOT
IGNITION:
Downward vertical vent runs are NOT
permitted.
NOTE: MODELS EQUIPPPED WITH
INTERMITTENT PILOT IGNITION:
Downward vertical vent runs are
permitted, however, Cold Climate Switch
(Standing Pilot Mode) must not be used.
74
PVH58 WALL THIMBLE INSTALLATION
An 11 inch square opening is required. Center Wall Thimble over the 11 inch square opening and secure both pieces on
either sides of the wall. Ensure that cutout is at the lower right corner, as electrical conduit must pass through this area.
Cutout At Lower
Right Corner when
looking into building.
Telescopic Wall Thimble
PVH58
POWER VENT MOUNTING
Route wiring harness through wall thimble. Mount Power Vent unit onto building. Use silicone around Power Vent
mounting flange to provide waterproof seal. Secure venting to Power Vent by driving screws through Vent Pipe Attachment
Straps. All vent connections must be sealed with high temp sealant, such as Black Mill Pack.
Apply Silicone
Vent Pipe Attachment Strap – Secure to Venting
11” x 11” Framed
Opening In Wall
!WARNING
Improper Installation may
cause water damage.
Use silicone sealant on Power
Vent mounting flange and
wiring harness opening.
12” LENGTH OF HARD PIPE MUST
BE CONNECTED DIRECTLY TO
POWER VENT TO PASS THROUGH
WALL THIMBLE
Wiring Harness
ALL VENT CONNECTIONS
MUST BE SEALED WITH HIGH
TEMP SEALANT, SUCH AS
BLACK MILL PACK.
Seal this area with silicone
once installation is complete
If you wish to use Flex Pipe,
connect adapters to end of 12”
hard pipe section (Refer to
Hard Pipe or Flex section)
Seal this area with silicone
once installation is complete
Vent Pipe
Attachment Strap
Wiring Harness
75
PVH58
WARNING
A qualified electrician must connect
electrical wiring to junction outlet for
built-in installation.
Follow all codes.
Wiring Harness Connections
WARNING
Electrical Grounding Instructions –
This appliance is equipped with a
three – pronged (grounding) plug for
your protection against shock hazard
and should be plugged directly into a
properly grounded three-prong
receptacle.
WARNING
Label all wires prior to disconnection
when servicing controls. Wiring errors
can cause improper and dangerous
operation. Verify proper operation and
servicing.
Caution: Electrical installation to be done by a qualified installer. All wires must be connected and grounded in accordance
with CSA Standard C22.1- Canadian Electrical Code part 1 or with the National Electrical Code, ANSI /NFPA 70 (latest edition) and
/or in accordance with local codes.
PVH58 EXTENSION HARNESS
The PVH58 comes supplied with a 20 foot wiring harness. If required, more
harnesses can be ordered. These harnesses are male to female, and can be
connected together.
Strain Relief: If extension harnesses are used, connect them using a junction box,
as shown.
This will provide strain relief and ensure that the connection does not come apart.
CONNECTION OF WIRING HARNESS AT FIREPLACE
Wiring Harness enters
fireplace here
(See photos below).
Extension Harness Connection
Insert Wiring Harness through specified 7/8” opening in unit. Push on connector until it snaps into place.
FOLLOW EITHER MILLIVOLT OR IPI SYSTEM INSTRUCTIONS TO COMPLETE
THE INSTALLATION.
76
PVH58
Millivolt System Connections
GREEN/GRND
10ft Double Pole Switch Wiring Harness for Millivolt Systems.
Connects to Double Pole Switch as Shown. A 20ft extension
harness can be ordered. See Wiring Harness Connections
section for installation of extension harness.
DOUBLE POLE
SWITCH
POWER VENT
BROWN
RED
BLACK
WHITE
Route Switch
Wiring Harness
through second
7/8” opening in
fireplace as
shown.
Power Vent
Control Module
Mount Power Vent Control Module in fireplace.
NOTE:
Fireplace glass
door must be
removed to
Install or remove
Power Vent
Control Module.
77
Connect to TH and TH / TP Tabs on Valve
Connect to Power Vent Cable
Connect to Double Pole Switch Cable
Plug into120v AC Outlet
DOUBLE POLE SWITCH
(SUPPLIED)
MILLIVOLT POWER VENT CONTROL MODULE
FIREPLACE IS SUPPLIED
WITH ONE JUNCTION BOX.
ADDITIONAL OUTLETS
MAY BE REQUIRED.
CONSULT A QUALIFIED
ELECTRICIAN.
THERMOSTATS AND REMOTE CONTROLS ARE NOT AVAILABLE FOR MILLIVOLT SYSTEMS.
SWITCH MUST BE “ON” AND POWER VENT BLOWER MUST BE RUNNING FOR APPLIANCE TO OPERATE.
NOTE: MODELS EQUIPPPED WITH MILLIVOLT/ STANDING PILOT IGNITION:
Downward vertical vent runs are NOT permitted.
78
PVCM Schematic - Millivolt
79
PVH58
IPI SYSTEM CONNECTIONS
Mount Power Vent Control Module in Fireplace.
NOTE:
Fireplace glass
door must be
removed to
Install or remove
Power Vent
Control Module.
Power Vent Control Module Mounted inside fireplace.
NOTE: MODELS EQUIPPPED WITH MILLIVOLT/
STANDING PILOT IGNITION:
Downward vertical vent runs are NOT permitted.
WIRING
HARNESS
NOTE: MODELS EQUIPPPED WITH INTERMITTENT
PILOT IGNITION:
Downward vertical vent runs are permitted, however, Cold
Climate Switch (Standing Pilot Mode) must not be used.
FIREPLACE IS SUPPLIED
WITH ONE JUNCTION BOX.
ADDITIONAL OUTLETS
MAY BE REQUIRED.
CONSULT A QUALIFIED
ELECTRICIAN.
POWER VENT
CONTROL MODULE
IPI
SYSTEM
Connect Wiring
Cold Climate Switch Must Be Disconnected From IPI Wiring Harness. Remove Batteries From Battery Backup.
80
PVH58
Basic IPI System Connections
RECOMMENDED METHOD OF CONNECTION:
First ensure the entire IPI system is working properly without connecting any
Power Vent components. Then connect the Power Vent Control Module.




PV1A – Valve
PV1B – Orange Wire on 912 Harness
PV2 – Power Vent
PV3A – Green Wire on 912 Harness
-On/Off Switch
 PV3B – Black / Red Wires on 912 Harness
 PV3C – Adapter
 PV4 – 120 VAC
*In the U.S.A. Thermostats are not
permitted for Vented Gas Fireplaces (ANSI
Z21.50b-2009 -Decorative).
81
PVH58
All IPI System Connections
RECOMMENDED METHOD OF CONNECTION:
First ensure the entire IPI system is working properly without connecting any
Power Vent components. Then connect the Power Vent Control Module.




PV1A – Valve
PV1B – Orange Wire on 912 Harness
PV2 – Power Vent
PV3A – Green Wire on 912 Harness
-Green Wire on 905 Harness
 PV3B – Black / Red Wires on 912 Harness
 PV3C – Adapter
 PV4 – 120 VAC
*In the U.S.A. Thermostats are not
permitted for Vented Gas Fireplaces (ANSI
Z21.50b-2009 -Decorative).
82
PVCM Schematic - IPI
83
84
PVH58
Air Intake Adjustment
The PVH58 is shipped with the air intake adjustment fully closed. This will produce maximum draw at the fireplace.
Longer runs require more draw, while shorter runs require less.
If flame pattern is slow and lazy, and sooting is occurring, more draw is required.
If flame pattern is running too fast, less draw is required.
Flame pattern should appear similar to below:
-AIR INTAKE ADJUSTMENTIf air intake adjustment is required, loosen screw at bottom of Power Vent as shown. Move adjuster slightly while having a
helper watch the flame pattern. Once the desired draw has been set, re-tighten adjuster screw.
Loosen screw at bottom of Power Vent
Once the desired draw has been set, re-tighten adjuster
screw.
Move adjuster while having a helper watch the flame
pattern.
Air Intake has been set.
85
PVH58
Troubleshooting
NOTE: Before connecting Power Vent Control Module, ensure that all other systems and accessories
(Remote Control, Fan, Lights, etc.) are connected and working properly.
!WARNING
BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE THE GLASS FRONT. BEFORE
TROUBLESHOOTING THE GAS CONTROL SYSTEM, BE SURE EXTERNAL GAS SHUT OFF IS IN THE "ON"
POSITION.
!WARNING
ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH THE
GLASS DOOR OPENED OR REMOVED. PURGE SHOULD BE PERFORMED BY A QUALIFIED SERVICE
TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT THE BURNER BEFORE CLOSING THE DOOR.
ENSURE ADEQUATE VENTILATION.
PROBLEM
Power Vent Blower will not
come on.
POSSIBLE CAUSES
No power is supplied to module.
Wires are unplugged.
CORRECTIVE ACTION
Plug PVCM into 120VAC
Source
Check connections.
Power Vent Blower runs
constantly
Wiring connected improperly
Check connections with wiring
diagram. For IPI, ensure that
wire PV3-A is plugged into the
green wire on the 912 or 905
harness, and not the white.
Main Burner will not come on.
Vacuum switch is not closed.
Check / replace vacuum hose.
Check / replace vacuum switch.
Main Burner Flame is lazy,
sooting is occurring.
Air Intake Requires Adjustment
See Air Intake Adjustment
Section
Check Installation
Leaking Exhaust Vent
Main Burner Flame is running
very fast
Air Intake Requires Adjustment
See Air Intake Adjustment
Section
86
PVH58
Parts List
PVH58 HORIZONTAL POWER VENT TERMINATION:
Listed for Canada and USA
NUMBER
DESCRIPTION
ZCV39 & ZCV42 VENTING AND VENTING ADAPTERS
-For fireplaces to be converted to hard pipe (Duravent-DirectVent Pro, etc.) at the fireplace:
ZDVDFA
Duravent Fireplace Adapter
ZDVDIA
Duravent Pipe Increaser (Adapts 4/6-5/8” venting to 5/8”)
-For Power Vent installations where flex pipe will be used up to the Power Vent unit:
Z47PVA
Pipe Reducer 8”Sm – 7”Sm, Pipe Reducer 5”Sm – 4”Sm (Adapts PVH58 to accept 4/7” Flex
Pipe
* One 12” section of hard pipe must be connected directly to the Power Vent before any adapters are connected.
Order the appropriate lengths of venting (see below).
ZDVFK5
Flex Kit (4” & 7” Dia.) x 2.5’ (Unexpanded) 5’ Expanded
ZDVFK8
Flex Kit (4” & 7” Dia.) x 4’ (Unexpanded) 8’ Expanded
ZDVFK20
Flex Kit (4” & 7” Dia.) x 10’ (Unexpanded) 20’ Expanded
*Kits are complete with spring stand-offs & silicone.
ZDV4FC
Flex Connector 4” Diameter
ZDV7FC
Flex Connector 7” Diameter
ZDV4SS
Spring - Standoff Spacer for Inner Pipe
PVH58 TERMINATION COMPONENT PARTS:
58PVH-230S
Blower Motor and Housing Assembly
58PVH-230F
Blower Motor and Housing Assembly
58PVH-P118
Gasket
58PVH-P9372
Vacuum Switch
58PVH-P119
58PVH-P3211
Silicone Tubing for Vacuum Switch
58PVH-WTA
Wall Thimble Assembly
PVH20H
Main Wiring Harness Assembly – Extension Harness (20ft)
PVC58MV
3/4” K.O. Bushing
Power Vent Control Module – Millivolt Box
58PVH-P124
Double Pole Switch
58PVH-P421
Timer Switch
PVC58IPI
Power Vent Control Module – IPI Box
58PVH-P421
Timer Switch
58PVH-P156
Relay
58PVH-P487
Relay Socket
87
ZCV39
Parts List
Fireplace Part Numbers
ZCV39N
ZCV39NH
ZCV39NE
ZCV39NHE
ZCV39LP
ZCV39LPH
ZCV39LPE
ZCV39LPHE
(Millivolt) Fireplace Decorative rated, NG,
Tempered Glass, Safety Screen
(Millivolt) Fireplace Heater rated, NG,
Ceramic Glass, Safety Screen
(IPI) Fireplace Decorative Rated NG,
Tempered Glass, Safety Screen
(IPI) Fireplace Heater Rated NG, Ceramic
Glass, Safety Screen
(Millivolt) Fireplace Decorative Rated LP,
Tempered Glass, Safety Screen
(Millivolt) Fireplace Heater Rated LP,
Ceramic Glass, Safety Screen
(IPI) Fireplace Decorative Rated LP,
Tempered Glass, Safety Screen
(IPI) Fireplace Heater Rated LP, Ceramic
Glass, Safety Screen
Wall Surrounds ZCV39
ZCV39S1BL
Surround - Hearth Mount
(40-5/8”W x 35”) Black
ZCV39S1PFBL
Surround – Wide Picture Frame
(40-5/8”W x 37” x 4”) Black
ZCV39S2PFBL
ZCV-TLK
Surround - Picture Frame
(36-1/8”W x 32-1/2” x 1-5/8”) Black
Tile Lip Kit
ZCV39 Options
Log Set- 5 Pcs
Log Bits - Large Four Piece Kit
Log Bits - Small Six Piece Kit
Glass Tray- Requires 15LBS Glass
39ZCV-258
Pilot Shield - for ZCV39GT
ZG5C
RBCB1
ULK2
3927ZDV-P779-1
Decorative Ember Glass –Bronze 5LB
Cannonballs- Assorted size and colors
Universal Light Kit
Bulb 10W 12V 64418 or [Sylvania 58691]
(light bulbs NOT covered under Warranty.)
Lamp Assembly 58mm (light bulbs NOT
covered under Warranty.)
Transformer MET60-1
3927ZDV-P601
ZCV39 Options – MQ Dealer Only MQ39DD1BL
MQ39DD2BL
MQ39DD3BL
MQLOG F9
MQ39D
MQSTONE
MQROCK2
MQROCK3
MQEMBER
MQG5W
MQG5A
MQG5B
MQG5ZG
Heavy Iron Door (38”W x 34-3/8”) Black
Heavy Iron Door (38”W x 34-3/8”) Black
Heavy Iron Door (38”W x 34-3/8”) Black
Log Set- 9pcs
Driftwood Log Set- 4pcs
Decorative Stones
Rock Set Natural
Rock Set Multi-Color
Glowing Embers
Decorative Glass 1/2” White 5LB
Decorative Ember Glass Cobalt Blue 5LB
Decorative Ember Glass – Black 5LB
Decorative Glass- Zircon Glacier Ice 5LB
Refractory Liners
ZCV39RLT
ZCV39RLH
Refractory Liner Traditional
Refractory Liner Herringbone
Refractory Liner Red Herringbone
Refractory Liner Stacked Brick
Porcelain Reflective Liner
Optional Fan Kit / Blower
Z46FK
26IDV-P260
Fan Kit w/Variable Speed Wall Mount
Control (Temperature Sensing)
Blower Motor (Replacement)
Child Safety Screens
ZCV39CSS
Child Safety Screen
Door Glass
39ZCV-310
39ZCV-311
51MQ-123A
Ceramic Glass- for Heater Rated Units
Tempered Glass- for Decorative Units
Door Latch Assembly
Replacement Burner Assembly / Burner
39ZCV-200A
39ZCV-BLPSI
39ZCV-BLPSIH
39ZCV-BNGSI
39ZCV-BNGSIH
39ZCV-BLPSIE
39ZCV-BLPSIHE
39ZCV-BNGSIE
LOG F3
VLBIT4
VLBIT6
ZCV39GT
5143-P77912
ZCV39RRH
ZCV39RLS
ZCV39PL
39ZCV-BNGSIHE
Fireplace Burner
Burner Assembly- Propane c/w Valve
System (ZCV39LP)
Burner Assembly- Propane c/w Valve
System (ZCV39LPH)
Burner Assembly- Natural Gas c/w Valve
System (ZCV39N)
Burner Assembly- Natural Gas c/w Valve
System (ZCV39NH)
Burner Assembly- Propane c/w Valve
System (ZCV39LPE)
Burner Assembly- Propane c/w Valve
System (ZCV39LPHE)
Burner Assembly- Natural Gas c/w Valve
System (ZCV39NE)
Burner Assembly- Natural Gas c/w Valve
System (ZCV39NHE)
Conversion Kit
39ZCV-CKLP
39ZCV-CKLPH
39ZCV-CKNG
39ZCV-CKNGH
39ZCV-CKLPI
39ZCV-CKLPHI
39ZCV-CKNGI
39ZCV-CKNGHI
LP Conversion Kit for 39ZCV Millivolt
LP Conversion Kit for 39ZCVH Millivolt
NG Conversion Kit for 39ZCV Millivolt
NG Conversion Kit for 39ZCVH Millivolt
LP Conversion Kit for 39ZCV IPI
LP Conversion Kit for 39ZCVH IPI
NG Conversion Kit for 39ZCV IPI
NG Conversion Kit for 39ZCVH IPI
Baffle Conversion Kit
39ZCV-BCKNG
39ZCV-BCKLP
NG Heater/ upgrade Kit for ZCV39N / NE to
ZCV39NH /NHE
LP Heater / upgrade Kit for ZCV39LP / LPE
to ZCV39LPH /LPHE
Accessories
Z1MT
Z80PT
Thermostat Millivolt Wall Mount
Thermostat Programmable Digital Millivolt
Wall Mount (1F80-40)
Valve System Parts / Millivolt
1000-P136WR
1001-P069SI
1001-P216SI
1001-P165SI
1001-P167SI
1001-P633SI
1001-P634SI
1001-P713SI
Generator / Thermopile
Electrode Sparker 915.069 TC SIT
Thermocouple 290.216 TC SIT
Orifice Pilot NG 977.165 TC SIT
Orifice Pilot LP 977.167 TC SIT
Valve Nova LP Hi/Lo 0820651
Valve Nova NG Hi/Lo 0820652
Pilot Burner LP 199.713 TC SIT
88
1001-P714SI
Pilot Burner NG 199.714 TC SIT
FDVHT
Horizontal Vent Termination, Wall Thimble,
Wall Thimble, 36” Flex Pipe, Mill Pac
Horizontal Square Termination Vent
Starter Kit -5 FT Length
Horizontal Vent Termination, Wall Thimble,
Wall Thimble, 60” Flex Pipe, Mill Pac
Vertical Vent Termination – with restrictor
for runs over 15ft
Horizontal Vent Termination
FDVHSQ
Horizontal Square Termination
Z47ST24
FDVHSCU
Horizontal Snorkel Termination
(24” Tall, 14-1/2” Center to Center)
Horizontal Snorkel Termination
(36” Tall, 26-1/2” Center to Center)
Safety Cage for Horizontal Snorkel
Termination
Safety Cage for Horizontal Termination
ZDVAIS
Attic Insulation Shield
ZDVVOS
Offset Support
ZDVFS
Firestop Spacer
ZDVRS
Roof Support
ZDVWT
Wall Thimble (Horizontal Venting)
ZDVSS
Siding Shield for FDVHT
ZDVSSLR
Siding Shield - Large Return
Remote Control / Millivolt
GFRC
GTRC
GTMRCN
GTMRCP
GTFRCN
GTFRCP
Remote Control Millivolt / IPI – On/Off
Remote Control Millivolt - Thermostat
Remote Control Millivolt –
Thermostat/Modulating - NG
Remote Control Millivolt –
Thermostat/Modulating - LP
Remote Control Millivolt –
Thermostat/Modulating/Fan - NG
Remote Control Millivolt –
Thermostat/Modulating/Fan - LP
Electronic Ignition/Remote Control IPI
EGTRC
EGTMRCN
EGTMRCP
EGTFRCN
EGTFRCP
Remote Control IPI (Thermostat)
Remote Control IPI
(Thermostat/Modulating - NG)
Remote Control IPI
(Thermostat/Modulating - LP)
Remote Control IPI
(Thermostat/Modulating/Fan - NG)
Remote Control IPI
(Thermostat/Modulating/Fan - LP)
Electronic Ignition Replacement Parts IPI
1006-P002si
1006-P003si
1002-P047si
1002-P033si
1002-P089si
1002-P113si
1002-P302si
1002-P850si
1002-P12BH
1002-P912si
1001-P166si
1001-P168si
1002-P013si
1002-P012si
1002-P016si
1002-P014si
Valve IPI (NG; Hi/Lo)
Valve IPI (LP; Hi/Lo)
Pilot Assembly (LP)
Pilot Assembly (NG)
Spark Electrode (Long)
Electrode Flame Sensor (Long)
IPI Ignition Board
AC Wall Adapter
Battery Pack
Wiring Harness
Orifice Pilot (NG)
Orifice Pilot (LP)
Stepper Motor (NG)
Stepper Motor (LP)
Hi/Lo Regulator (NG)
Hi/Lo Regulator (LP)
Miscellaneous Parts
1000-150GE
1000-150MP
1000-214
1000-215
1000-218
1000-227
1000-255
2000-080
1000-306
1000-085
FP15GC
Silicone GE Red IS806 #736
Hi-Temp Millpac Sealant 840099
Piezo-Igniter 1244-17 MARK 21
Pal Nut (18MMXI.5MM)BLK (1364.03)
Switch Ivory (1451/001)
Cover Ivory (86001/001)
Orifice Brass - (State Size)
Thermodisc 2450 (For Blower)
Thermalcord - Adhesive Back for Door
Frame
Control Variable Speed KBWC-13BV
Stainless Steel Gas Connector
ZDVHSKSQ5
FDVVT40
Z47ST36
Z57STSC
ZDVAAF
Galvanized Pipe 7” Dia. x 48”
(Vertical Installations)
Flashing 7” c/w Storm Collar (1/12 to 7/12)
ZDVAF2
Flashing 7” c/w Storm Collar (8/12 to 12/12)
ZDVAF3
Flashing 7” c/w Storm Collar Flat
ZDV7SC
Storm Collar 7”
ZDV48GP
ZDVFK5
ZDVFK8
Flex Kit (4” & 7” Dia.) x 2.5’ (Unexpanded)
5’ Expanded
Flex Kit (4” & 7” Dia.) x 4’ (Unexpanded)
8’ Expanded
ZDV4FC
Flex Kit (4” & 7” Dia.) x 10’ (Unexpanded)
20’ Expanded *Kits are complete with spring
stand-offs & silicone.
Flex Connector 4” Diameter
ZDV7FC
Flex Connector 7” Diameter
ZDV4SS
Spring 4” Standoff Spacer
ZDVFK20
Kingsman Fireplace Venting
ZDVHSK
ZDVHSK5
ZDVHSKSQ
Horizontal Vent Starter Kit - 3 FT Length
Horizontal Vent Termination, Wall Thimble,
36” Flex Pipe, Mill Pac
Horizontal Vent Starter Kit - 5 FT Length
Horizontal Vent Termination, Wall Thimble,
60” Flex Pipe, Mill Pac
Horizontal Square Termination Vent
Starter Kit -3 FT Length
89
ZCV42
Parts List
Fireplace Part Numbers
ZCV42N
ZCV42NH
ZCV42NE
ZCV42NHE
ZCV42LP
ZCV42LPH
ZCV42LPE
ZCV42LPHE
(Millivolt) Fireplace Decorative rated, NG,
Tempered Glass, Safety Screen
(Millivolt) Fireplace Heater rated, NG,
Ceramic Glass, Safety Screen
(IPI) Fireplace Decorative Rated NG,
Tempered Glass, Safety Screen
(IPI) Fireplace Heater Rated NG, Ceramic
Glass, Safety Screen
(Millivolt) Fireplace Decorative Rated LP,
Tempered Glass, Safety Screen
(Millivolt) Fireplace Heater Rated LP,
Ceramic Glass, Safety Screen
(IPI) Fireplace Decorative Rated LP,
Tempered Glass, Safety Screen
(IPI) Fireplace Heater Rated LP, Ceramic
Glass, Safety Screen
Wall Surrounds ZCV42
ZCV42S1BL
Surround - Hearth Mount
(44-11/16”W x 38-1/8”) Black
ZCV42S1PFBL
Surround – Wide Picture Frame
(44-11/16”W x 40-1/8” x 4”) Black
ZCV42S2PFBL
ZCV-TLK
Surround - Picture Frame
(40-3/16”W x 35-5/8” x 1-5/8”) Black
Tile Lip Kit
ZCV42 Options
Log Set- 5 Pcs
Log Bits - Large Four Piece Kit
Log Bits - Small Six Piece Kit
Glass Tray- Requires 20LBS Glass
39ZCV-258
Pilot Shield - for ZCV42GT
ZG5C
RBCB1
ULK2
3927ZDV-P779-1
Decorative Ember Glass –Bronze 5LB
Cannonballs- Assorted size and colors
Universal Light Kit
Bulb 10W 12V 64418 or [Sylvania 58691]
(light bulbs NOT covered under Warranty.)
Lamp Assembly 58mm (light bulbs NOT
covered under Warranty.)
Transformer MET60-1
3927ZDV-P601
ZCV42 Options – MQ Dealer Only MQ42DD1BL
MQ42DD2BL
MQ42DD3BL
MQLOG F9
MQ39D
MQSTONE
MQROCK2
MQROCK3
MQEMBER
MQG5W
MQG5A
MQG5B
MQG5ZG
Heavy Iron Door (42”W x 37-1/2”) Black
Heavy Iron Door (42”W x 37-1/2”) Black
Heavy Iron Door (42”W x 37-1/2”) Black
Log Set- 9pcs
Driftwood Log Set- 4pcs
Decorative Stones
Rock Set Natural
Rock Set Multi-Color
Glowing Embers
Decorative Glass 1/2” White 5LB
Decorative Ember Glass Cobalt Blue 5LB
Decorative Ember Glass – Black 5LB
Decorative Glass- Zircon Glacier Ice 5LB
Refractory Liners
ZCV42RLT
ZCV42RLH
Refractory Liner Traditional
Refractory Liner Herringbone
Refractory Liner Red Herringbone
Refractory Liner Stacked Brick
Porcelain Reflective Liner
Optional Fan Kit / Blower
Z46FK
26IDV-P260
Fan Kit w/Variable Speed Wall Mount
Control (Temperature Sensing)
Blower Motor (Replacement)
Child Safety Screens
ZCV42CSS
Child Safety Screen
Door Glass
42ZCV-310
42ZCV-311
51MQ-123A
Ceramic Glass- for Heater Rated Units
Tempered Glass- for Decorative Units
Door Latch Assembly
Replacement Burner Assembly / Burner
39ZCV-200A
42ZCV-BLPSI
42ZCV-BLPSIH
42ZCV-BNGSI
42ZCV-BNGSIH
42ZCV-BLPSIE
42ZCV-BLPSIHE
42ZCV-BNGSIE
LOG F3
VLBIT4
VLBIT6
ZCV42GT
5143-P77912
ZCV42RRH
ZCV42RLS
ZCV42PL
42ZCV-BNGSIHE
Fireplace Burner
Burner Assembly- Propane c/w Valve
System (ZCV42LP)
Burner Assembly- Propane c/w Valve
System (ZCV42LPH)
Burner Assembly- Natural Gas c/w Valve
System (ZCV42N)
Burner Assembly- Natural Gas c/w Valve
System (ZCV42NH)
Burner Assembly- Propane c/w Valve
System (ZCV42LPE)
Burner Assembly- Propane c/w Valve
System (ZCV42LPHE)
Burner Assembly- Natural Gas c/w Valve
System (ZCV42NE)
Burner Assembly- Natural Gas c/w Valve
System (ZCV42NHE)
Conversion Kit
42ZCV-CKLP
42ZCV-CKLPH
42ZCV-CKNG
42ZCV-CKNGH
42ZCV-CKLPI
42ZCV-CKLPHI
42ZCV-CKNGI
42ZCV-CKNGHI
LP Conversion Kit for 42ZCV Millivolt
LP Conversion Kit for 42ZCVH Millivolt
NG Conversion Kit for 42ZCV Millivolt
NG Conversion Kit for 42ZCVH Millivolt
LP Conversion Kit for 42ZCV IPI
LP Conversion Kit for 42ZCVH IPI
NG Conversion Kit for 42ZCV IPI
NG Conversion Kit for 42ZCVH IPI
Baffle Conversion Kit
42ZCV-BCKNG
42ZCV-BCKLP
NG Heater / upgrade Kit for ZCV42N / NE to
ZCV42NH /NHE
LP Heater / upgrade Kit for ZCV42LP / LPE
to ZCV42LPH /LPHE
Accessories
Z1MT
Z80PT
Thermostat Millivolt Wall Mount
Thermostat Programmable Digital Millivolt
Wall Mount (1F80-40)
Valve System Parts / Millivolt
1000-P136WR
1001-P069SI
1001-P216SI
1001-P165SI
1001-P167SI
1001-P633SI
1001-P634SI
1001-P713SI
Generator / Thermopile
Electrode Sparker 915.069 TC SIT
Thermocouple 290.216 TC SIT
Orifice Pilot NG 977.165 TC SIT
Orifice Pilot LP 977.167 TC SIT
Valve Nova LP Hi/Lo 0820651
Valve Nova NG Hi/Lo 0820652
Pilot Burner LP 199.713 TC SIT
90
1001-P714SI
Pilot Burner NG 199.714 TC SIT
FDVHT
Horizontal Vent Termination, Wall Thimble,
Wall Thimble, 36” Flex Pipe, Mill Pac
Horizontal Square Termination Vent
Starter Kit -5 FT Length
Horizontal Vent Termination, Wall Thimble,
Wall Thimble, 60” Flex Pipe, Mill Pac
Vertical Vent Termination – with restrictor
for runs over 15ft
Horizontal Vent Termination
FDVHSQ
Horizontal Square Termination
Z47ST24
FDVHSCU
Horizontal Snorkel Termination
(24” Tall, 14-1/2” Center to Center)
Horizontal Snorkel Termination
(36” Tall, 26-1/2” Center to Center)
Safety Cage for Horizontal Snorkel
Termination
Safety Cage for Horizontal Termination
ZDVAIS
Attic Insulation Shield
ZDVVOS
Offset Support
ZDVFS
Firestop Spacer
ZDVRS
Roof Support
ZDVWT
Wall Thimble (Horizontal Venting)
ZDVSS
Siding Shield for FDVHT
ZDVSSLR
Siding Shield - Large Return
Remote Control / Millivolt
GFRC
GTRC
GTMRCN
GTMRCP
GTFRCN
GTFRCP
Remote Control Millivolt / IPI – On/Off
Remote Control Millivolt - Thermostat
Remote Control Millivolt –
Thermostat/Modulating - NG
Remote Control Millivolt –
Thermostat/Modulating - LP
Remote Control Millivolt –
Thermostat/Modulating/Fan - NG
Remote Control Millivolt –
Thermostat/Modulating/Fan - LP
Electronic Ignition/Remote Control IPI
EGTRC
EGTMRCN
EGTMRCP
EGTFRCN
EGTFRCP
Remote Control IPI (Thermostat)
Remote Control IPI
(Thermostat/Modulating - NG)
Remote Control IPI
(Thermostat/Modulating - LP)
Remote Control IPI
(Thermostat/Modulating/Fan - NG)
Remote Control IPI
(Thermostat/Modulating/Fan - LP)
Electronic Ignition Replacement Parts IPI
1006-P002si
1006-P003si
1002-P047si
1002-P033si
1002-P089si
1002-P113si
1002-P302si
1002-P850si
1002-P12BH
1002-P912si
1001-P166si
1001-P168si
1002-P013si
1002-P012si
1002-P016si
1002-P014si
Valve IPI (NG; Hi/Lo)
Valve IPI (LP; Hi/Lo)
Pilot Assembly (LP)
Pilot Assembly (NG)
Spark Electrode (Long)
Electrode Flame Sensor (Long)
IPI Ignition Board
AC Wall Adapter
Battery Pack
Wiring Harness
Orifice Pilot (NG)
Orifice Pilot (LP)
Stepper Motor (NG)
Stepper Motor (LP)
Hi/Lo Regulator (NG)
Hi/Lo Regulator (LP)
Miscellaneous Parts
1000-150GE
1000-150MP
1000-214
1000-215
1000-218
1000-227
1000-255
2000-080
1000-306
1000-085
FP15GC
Silicone GE Red IS806 #736
Hi-Temp Millpac Sealant 840099
Piezo-Igniter 1244-17 MARK 21
Pal Nut (18MMXI.5MM)BLK (1364.03)
Switch Ivory (1451/001)
Cover Ivory (86001/001)
Orifice Brass - (State Size)
Thermodisc 2450 (For Blower)
Thermalcord - Adhesive Back for Door
Frame
Control Variable Speed KBWC-13BV
Stainless Steel Gas Connector
ZDVHSKSQ5
FDVVT40
Z47ST36
Z57STSC
ZDVAAF
Galvanized Pipe 7” Dia. x 48”
(Vertical Installations)
Flashing 7” c/w Storm Collar (1/12 to 7/12)
ZDVAF2
Flashing 7” c/w Storm Collar (8/12 to 12/12)
ZDVAF3
Flashing 7” c/w Storm Collar Flat
ZDV7SC
Storm Collar 7”
ZDV48GP
ZDVFK5
ZDVFK8
Flex Kit (4” & 7” Dia.) x 2.5’ (Unexpanded)
5’ Expanded
Flex Kit (4” & 7” Dia.) x 4’ (Unexpanded)
8’ Expanded
ZDV4FC
Flex Kit (4” & 7” Dia.) x 10’ (Unexpanded)
20’ Expanded *Kits are complete with spring
stand-offs & silicone.
Flex Connector 4” Diameter
ZDV7FC
Flex Connector 7” Diameter
ZDV4SS
Spring 4” Standoff Spacer
ZDVFK20
Kingsman Fireplace Venting
ZDVHSK
ZDVHSK5
ZDVHSKSQ
Horizontal Vent Starter Kit - 3 FT Length
Horizontal Vent Termination, Wall Thimble,
36” Flex Pipe, Mill Pac
Horizontal Vent Starter Kit - 5 FT Length
Horizontal Vent Termination, Wall Thimble,
60” Flex Pipe, Mill Pac
Horizontal Square Termination Vent
Starter Kit -3 FT Length
91
This Limited Lifetime Warranty applies only while the unit remains at the site of the original installation
and only if the unit is installed inside the continental United States, Alaska, Hawaii, and Canada. The
warranty applies only if the unit is installed and operated in accordance with the printed instructions and
in compliance with applicable installation and building codes and good trade practices.
BASIC ONE YEAR WARRANTY
During the first year after installation, we will provide a replacement for any component part of your unit found to be defective in
materials or workmanship, including labour costs. Repair work requires prior approval by Kingsman, labour costs are based on a
predetermined rate schedule and any repair work must be done through an authorized Kingsman dealer.
(Excluded Components: Accent Light Bulbs, Gasketing and Paint)
LIMITED LIFETIME WARRANTY
The heat exchanger, combustion chamber and burner of every Kingsman product excluding the Outdoor Firepit are warranted against
materials or workmanship during the period the product is owned by the original owner. The part to be replaced must be returned to our
distributor in exchange for the replacement part. Any labor, material, freight and/or handling charges associated with any repair or
replacement pursuant to this Limited Lifetime Warranty will not be covered by this warranty.
GENERAL TERMS
In lieu of providing a replacement part, we may, at our option, provide the distributor's component purchase price from us or a credit
equal to the distributor’s component purchase price from us toward the purchase of any new unit which we distribute. If a credit is given
in lieu of a replacement part, the rating plate from the unit being replaced must be submitted on a warranty claim, and the unit being
replaced must be made available to our distributor for disposition.
In establishing the date of installation for any purpose, including determination of the starting date for the term of this Limited Lifetime
Warranty, reasonable proof of the original installation date must be presented*, otherwise the effective date will be based upon the date
of manufacture plus thirty (30) days.
We will not be responsible for and you, the user, will pay for: (a) damages caused by accident, abuse, negligence, misuse, riot, fire,
flood, or Acts of God (b) damages caused by operating the unit where there is a corrosive atmosphere containing chlorine, fluorine, or
any other damaging chemicals (other than in a normal residential environment) (c) damages caused by any unauthorized alteration or
repair of the unit affecting its stability or performance (d) damages caused by improper matching or application of the unit or the unit's
components (e) damages caused by failing to provide proper maintenance and service to the unit (f) any expenses incurred for
erecting, disconnecting or dismantling the unit (g) parts or supplies used in connection with service or maintenance (h) damage repairs,
inoperation or inefficiency resulting from faulty installation or application (i) electricity or fuel costs or any increase in electricity or fuel
cost whatsoever including additional or unusual use of supplemental electric heat.
We shall not be liable for any incidental, consequential, or special damages or expenses in connection with any use or failure of this
unit. We have not made and do not make any representation or warranty of fitness for a particular use or purpose, and there is no
implied condition of fitness for a particular use or purpose. We make no express warranties except as stated in this Limited Lifetime
Warranty. No one is authorized to change this Limited Lifetime Warranty or to create for us any other obligation or liability in
connections with this unit. Any implied warranties shall last for one year after the original installation. Some states and provinces do not
allow the exclusion or limitation of incidental or consequential damages or do not allow limitations on how long an implied warranty or
condition lasts, so the above limitations or exclusions may not apply to you. The provisions of this limited warranty are in additions to
and not a modification of or subtraction from any statutory warranties and other rights and remedies provided by law.
Save this certificate. It gives you specific legal rights, and you may also have other rights which may vary from state to state and
province to province.
In the event your unit needs servicing, contact your dealer or contractor who installed or serviced your unit. When requesting service,
please have the model and serial number from each unit readily available. If your dealer needs assistance, the distributor is available
for support and we, in turn support the distributor's efforts.
Fill in the installation date and model and serial numbers of the unit in the space provided below and retain this limited warranty for your
files.
Model No.
Serial No.
Date installed
Dealer or Contractor Name:
*To receive advantage of your warranty, you must retain the original records that can establish the installation date of your unit.
The Ultimate in Design, Engineering & Quality
92