Mitsubishi Electric UNISEN LT-46151 Specifications

Add to my manuals
96 Pages

advertisement

Mitsubishi Electric UNISEN LT-46151 Specifications | Manualzz
IMMERSIVE SOUND LCD HDTV
with Integrated Sound Projector
MODELS
151 Series
153 Series
249 Series
LT-40151, LT-46151, LT-52151
LT-40153, LT-46153, LT-52153
LT-46249, LT-52249
OWNER’S GUIDE
•
•
•
•
•
Guidelines for setting up and using your new widescreen TV start on page 7.
For questions:
-- Visit our website at www.mitsubishi-tv.com.
-- E-mail us at [email protected].
-- Call Consumer Relations at 800-332-2119.
For information on System Reset, please see the back cover.
To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call
800-553-7278.
153 and 249 Series. IR emitter cables for NetCommand home-theater control are available for purchase
from Mitsubishi. Call 800-553-7278 and request either part number 242D483020 (two-ended cable) or part
number 299P254020 (four-ended cable).
Downloaded From TV-Manual.com Manuals
For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER
SERIAL NUMBER PURCHASE DATE
RETAILER NAME LOCATION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user of the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: This product shall be connected to a
MAINS socket outlet with a protective earthing connection.
MAINS DISCONNECTION: The mains plug is used
as the disconnect device. The mains plug shall remain
readily operable.
TV WEIGHT: This TV is heavy. Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and disconnect all cables before moving it.
FCC Declaration of Conformity
Product:
LCD Flat Panel HDTV
Models:
LT-40151, LT-46151, LT52151
LT-40153, LT-40153, LT-52153
LT-46249, LT-52249
Responsible Mitsubishi Digital Electronics
Party:
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone:
(800) 332-2119
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and the receiver.
-- Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/
TV technician for help.
Changes or modifications not expressly
approved by Mitsubishi could cause harmful
interference and would void the user’s authority
to operate this equipment.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
Downloaded From TV-Manual.com Manuals
Features and specifications described in this owner’s
guide are subject to change without notice.
Contents
Important Safety Instructions. . . . . . .
Important Information About Your TV..
Special Features of Your TV. . . . . . . .
1 Basic Setup and Operation
Package Contents. . . . . . . . .
Stand Installation. . . . . . . . . .
Wall-Mounting. . . . . . . . . . . .
Before You Begin.. . . . . . . . .
First-Time Power-On.. . . . . . .
TV Controls. . . . . . . . . . . . . .
Setting Up TV Inputs. . . . . . .
Basic TV Operation. . . . . . . .
. . . . . . . . .
. . . . . . . . .
. . . . . . . . .
7
. 8
. 8
. 9
. 9
10
12
14
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . .
. . . . . . . . . . . . . .
2 TV Connections
Before You Begin.. . . . . . . . . . . . . . . . .
Cable Management. . . . . . . . . . . . . . . .
Inputs and Outputs. . . . . . . . . . . . . . . .
Y Pb Pr Component Video Device. . . . . .
HDMI Device.. . . . . . . . . . . . . . . . . . . . . .
DVI Video Device. . . . . . . . . . . . . . . . . .
Composite Video Device.. . . . . . . . . . . .
Antenna or Cable TV Service.. . . . . . . . .
VCR or DVD Recorder to an Antenna or Wall Outlet Cable. . . . . . . . . . . . . . . . .
VCR or DVD Recorder to a Cable Box . . .
A/V Receiver. . . . . . . . . . . . . . . . . . . . .
A/V Receiver with HDMI Output. . . . . . .
Subwoofer.. . . . . . . . . . . . . . . . . . . . . .
Audio-Only Device. . . . . . . . . . . . . . . . .
3 Using TV Features
Selecting an Input. . . . . . . . . . . . . . . . .
Sleep Timer.. . . . . . . . . . . . . . . . . . . . .
ChannelView Channel Listings.. . . . . . . .
Redirecting Audio Output. . . . . . . . . . . .
Controlling A/V Receiver Volume. . . . . . .
Status Display. . . . . . . . . . . . . . . . . . . .
TV Signals and Display Formats. . . . . . .
Using the TV with a Personal Computer. .
Camera Images and Music Files. . . . . . .
Sound Projector.. . . . . . . . . . . . . . . . . .
Streaming Internet Movies with VUDU. . .
Introduction to Home-Theater Control. . .
Downloaded From TV-Manual.com Manuals
4
5
6
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
16
16
17
20
20
21
21
21
22
22
23
23
24
24
4 TV Menus
Main Menu. . . . .
Menu Navigation.
Adjust. . . . . . . . .
Captions. . . . . . .
Initial.. . . . . . . . .
Inputs. . . . . . . . .
Lock. . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
5 NetCommand IR Control
About NetCommand IR Control.. . . . . . . . . .
IR Emitter Placement. . . . . . . . . . . . . . . . . .
Initial NetCommand Setup. . . . . . . . . . . . . .
Operating NetCommand-Controlled Devices.
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
. . . . . .
25
25
26
26
26
27
28
29
31
34
37
39
. . .
. . .
. . .
55
56
57
58
6 NetCommand IR Control of an A/V Receiver
Controlling an A/V Receiver after NetCommand Setup.. . . . . . . . . . . . . . . . . . . . 61
Setting Up A/V Receiver Control
Power and Volume. . . . . . . . . . . . . . . . . . . . 62
Automatic Switching (Audio or Audio/Video). . 63
Appendices
Appendix A: Programming the Remote Control.
Appendix B: HDMI Control of CEC Devices. . . .
Appendix C: TV Care.. . . . . . . . . . . . . . . . . . .
Appendix D: Bypassing the Parental Lock. . . . .
Appendix E: Troubleshooting. . . . . . . . . . . . . .
.
68
75
78
79
81
. . . . . . . . .
88
. . . . . . . . . . . . . . .
88
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
94
Trademark and License Information. .
Network Service Disclaimer. .
. . . . . .
. . .
40
40
41
46
47
50
52
Warranty.
Index. .
.
.
.
.
4
Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
E XAMP LE OF ANT E NNA G R OUNDING
1) Read these instructions.
2) Keep these instructions.
ANT E NNA
LE AD IN WIR E
G R OUND C LAMP
ANT E NNA
DIS C HAR G E UNIT
(NE C AR T IC LE 810-20)
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
E LE C T R IC
S E R V IC E
E QUIP ME NT
6) Clean only with dry cloth.
G R OUND C LAMP S
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Downloaded From TV-Manual.com Manuals
G R OUNDING
C ONDUC T OR S
(NE C AR T IC LE 810-21)
NE C — NAT IONAL E LE C T R IC AL C ODE
P OWE R S E R V IC E G R OUNDING
E LE C T R ODE S Y S T E M
(NE C AR T 250, P AR T H)
Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
5
Important Information About Your TV
Installation Notes
If Your TV Gets Damaged
For stand installation and wall-mounting, see page 8.
Crystalline liquid may leak from the LCD panel and
broken glass may be scattered.
Use with other than the authorized accessories
may cause the TV to become unstable, which can
cause damage to the product or possible injury.
Custom cabinet installation must allow for proper
air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER
IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND
SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY
AS PRACTICAL.
TV Software
Do not attempt to update the software of this TV with
software or USB drives not provided by or authorized by
Mitsubishi Digital Electronics America, Inc. Non-authorized
software may damage the TV and will not be covered by
the warranty.
Downloaded From TV-Manual.com Manuals
CAUTION: The crystalline liquid is toxic. Avoid
contact with your skin, eyes, or mouth. DO NOT
touch the broken glass or crystalline liquid. DO NOT get
glass fragments or crystalline liquid into eyes or mouth. Should either contact your eyes or mouth, rinse the
contacted area thoroughly with water and consult
your doctor.
Disposal of Your TV
The LCD panel contains a small amount of crystalline
liquid and the fluorescent tube in the panel contains
mercury. Both are toxic and should not be touched.
DO NOT dispose of the TV with general household
waste. THE LAMPS INSIDE THIS PRODUCT CONTAIN
MERCURY AND MUST BE RECYCLED OR DISPOSED
OF ACCORDING TO LOCAL, STATE, AND FEDERAL
LAWS. For disposal or recycling information, contact
your local authorities or the Electronic Industries Alliance at www.eiae.org.
6
Special Features of Your TV
Your new high-definition widescreen television has
many special features that make it the perfect center of
your home entertainment system, including:
1080p High-Definition LCD Display System
Your Mitsubishi LCD Flat Panel HDTV uses a full 1920
x 1080 LCD panel to create the picture you see on the
screen. All images are displayed at 1080p. The TV uses
new Plush 1080p® 5G digital video processing to convert
lower-resolution signals to 1080p for display.
Smooth120Hz™ Film Motion
Smooth120Hz™ Film Motion makes fast-moving images
appear smoother and more fluid, free from motion blur. It
does this by doubling the traditional progressive scan
frame rate and creates new frames of video between the
traditional frames to create smoother moving images. Smooth120Hz™ Film Motion also smooths film judder
(image vibration) that may be present in film-based
content such as movies.
16:9 Widescreen Picture Format
Enjoy a full theatrical experience in the comfort of your
home. View pictures as film directors intended them.
Digital TV broadcasts, DVDs and newer video game
consoles support this widescreen format.
Integrated HDTV Tuner
Your widescreen Mitsubishi HDTV has an internal HDTV
tuner able to receive both over-the-air HDTV broadcasts (received via an antenna) and non-scrambled
digital cable broadcasts, including non-scrambled
HDTV cable programming.
High-Definition Video Inputs
•
•
Component Video Inputs. Also called Y/Pb/Pr
inputs, these inputs receive standard analog video
formats of 480i, 480p, 720p, and 1080i high-definition signals. This provides a high level of flexibility
when connecting DVD players/recorders, cable
boxes, and satellite receivers.
HDMI Inputs. These inputs accept digital 480i,
480p, 720p, 1080i, and 1080p video signals plus
bitstream and PCM digital stereo signals. The
HDMI™ inputs can also accept a variety of PC
signals and resolutions. These inputs support
HDMI 1.3 Deep Color (up to 36 bits) and the
x.v.Color extended color gamut.
Used with an adapter, these inputs also accept
compatible digital DVI video signals. HDMI
inputs provide additional high-performance,
high-definition connections for maximum flexibility
in your choice of home theater products. The HDMI
inputs are HDCP copy-protection compatible.
Downloaded From TV-Manual.com Manuals
Easy Connect Auto Input Sensing
Easy Connect™ Auto Input Sensing automatically recognizes when you plug in a device and prompts you to
assign a name to it.
Home-Theater Control
HDMI Control
Available for all models. HDMI devices with Consumer
Electronics Control (CEC) capabilities may be compatible
with the TV’s HDMI Control feature. Compatible devices
can receive control signals through the HDMI connection,
allowing the TV’s remote control to operate some functions of these devices.
NetCommand with IR Learning
153 and 249 Series. Your Mitsubishi HDTV offers a new
level of networking that seamlessly integrates selected
older A/V products with new and future digital products. NetCommand® supports IR (infrared) control of products
such as VCRs, DVD players, cable boxes, and satellite receivers. NetCommand can “learn” remote control
signals directly from many devices, allowing you to create
a customized NetCommand-controlled home-theater
system.
Sound Projector
Sound Projector technology uses the TV’s bank of
speakers to create a simulated surround sound effect
by reflecting sound off the room walls.
Internet Video Streaming with VUDU™
249 Series. VUDU offers the largest on-demand HD
movie selection anywhere, featuring full 1080p and 5.1
surround sound. VUDU allows you to enjoy movies with no
store visits, no mailing, no late fees and no subscriptions.
ENERGY STAR®
This is an ENERGY STAR® qualified TV. Products that
earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set
by the U.S. Environmental Protection Agency and the
U.S. Department of Energy. This TV consumes power
in excess of ENERGY STAR guidelines under the following conditions:
TV Feature Active
Picture Mode set to Brilliant
TV Power
Status
On
Fast Power On enabled
153 and 249 Series. External Controller
Input enabled
Off
1
Basic Setup and Operation
Package Contents
Please take a moment to review the following list of
accessory items to ensure that you have received
everything.
Remote Control Batteries
1. Remove the remote control back cover.
ACTIVITY
GUIDE
MENU
INFO
BACK
1. Remote Control
7
2. Two AA Batteries
AA
AA
Emitter
Bulb
3. Basic Owner’s
Guide
2. Load the batteries, making sure the polarities
(+) and (-) are correct. Insert the negative (-)
end first.
4. HDTV Quick Setup
Guide
5. Product Registration Card
6. Power Cord
3. Slide the cover back into place.
7. Cable Tie
8. Stand Screws
9. 153 and 249 Series.
Calibration Microphone
Downloaded From TV-Manual.com Manuals
8
1. Basic Setup and Operation
CAUTION: Using this TV with other than the authorized accessories may cause the TV to become unstable,
which can cause damage to the product or possible injury.
Stand Installation
Required: Phillips Screwdriver
1
1
Extension pieces
on back of stand
Extension pieces
on back of stand
Back
2
3
2
Back
CAUTION
At least TWO PEOPLE are
required to install the stand. Support
the TV near the corners as shown. Failure to
follow these recommendations may result in
personal injury and damage to the
product.
DO support the TV
under the corners.
DO support the TV
under the corners.
DON’T place your hand where it can get
caught between the TV and stand.
DON’T place your hand where it can get
Two adults are required to lift the TV.
caught between the TV and stand.
TV in protective
Two adults are required to lift the TV.
wrapping
3
Repacking the Stand
TV in protective
wrapping
Place the
CAUTION.
Repacking
the Stand
TV
stand in the foam insert
Place the
CAUTION.
with the extension
pieces
TV
stand
in the
facing away
from
the foam
TV. insert
with
the
extension
Otherwise, the TV will be pieces
away from the TV.
damagedfacing
in transit.
Otherwise, the TV will be
Protect the
TV andin transit.
damaged
stand with the original
packing Protect
material.the TV and
stand with the
originalpieces on stand
Extension
packing material.
must face out, away from TV.
Extension pieces on stand
must face out, away from TV.
Wall-Mounting
If planning to wall-mount the TV, do not install the
stand. To order a wall-mount kit, please contact
Peerless Industries, Inc. at (800) 473-3753 or visit
www.peerlessmounts.com. Order wall-mount kit model
ST650.
Downloaded From TV-Manual.com Manuals
To order a wall-mount kit from Mitsubishi Digital Electronics America, Inc., please visit www.mitsuparts.com
or call (800) 553-7278.
Complete installation instructions are included with the kit.
9
1. Basic Setup and Operation
Before You Begin
1. Review the important safety, installation, and oper2.
ating information at the beginning of this book.
Choose a location for your TV.
• See the stand-installation or wall-mounting
requirements on the opposite page.
• Allow at least four inches of space on all sides
of the TV to help prevent overheating. Overheating may cause premature failure of the TV.
• Avoid locations where light may reflect off the
screen.
3. Install the batteries in the remote control.
4. Plug the TV into an AC power outlet.
First-Time Power-On
1. Confirm that the remote
control is in TV mode. • Press the side button
once to light the mode
indicator and confirm
that TV mode is active.
• To change, press the
side button additional
times to activate TV
mode.
TV
GUIDE
MENU
INFO
BACK
2. Aim the remote control
at the TV and press the
POWER key
. Wait for the
Welcome screen.
GUIDE
MENU
INFO
BACK
3. Press
if you wish to
change the menu language
to Español.
4. Press
to move to the
energy-mode selections. See the information box for
details.
TV power connection
5. Press
to highlight EXIT.
Press ENTER to clear the
menu.
Welcome Screen Energy Options
• Mitsubishi recommends the Home setting, which
uses power within ENERGY STAR® guidelines.
• Home Fast Power On allows the TV to power up
quickly. While powered off, however, the TV uses
power in excess of ENERGY STAR guidelines for
a powered-down device.
• The Retail setting looks best under bright lighting. In this mode, the TV uses power in excess
of ENERGY STAR guidelines.
This table compares energy choices offered in the
Welcome screen.
Downloaded From TV-Manual.com Manuals
Home
Home Fast
Power On Retail
Picture Mode
Bright
Bright
Brilliant
Backlight
Level
Reduced
Brightness
Reduced
Brightness
Full Brightness
Time to
Power On
Normal
Fast
Normal
10
1. Basic Setup and Operation
TV Controls
Remote Control
GUIDE ChannelView listings, page 26.
VCR CABL/SAT TV DVD AUDIO
Control-mode indicator for device
type to control. Use the side button to
change.
MENU TV main menu, page 40
Powers TV on or off
Press to select a TV activity and input. See page 25.
INFO TV status (page 27) or TV help.
BACK
Steps back one menu; clears
the top menu or Status Display.
ACTIVITY
GUIDE
MENU
INFO
Side button sets the control mode
for the type of device to operate. Set
mode to TV for normal TV viewing.
BACK
CHANNEL UP
Volume Up
LAST. Returns to the previously tuned channel.
MUTE
CHANNEL DOWN
VOLUME DOWN
PAGE UP
Record/Playback controls for external devices
When remote control is programmed, page 68
HDMI control, page 77
153 and 249 Series: NetCommand, page 58
(Pause) Freezes a broadcast TV picture.
249 Series: See page 68.
MORE
Number/letter keys
Channel tuning, page 14
•
•
F1
F2
F3
Navigation controls
PAGE DOWN
ON
DEMAND
FAV
Adds a separator when entering digital
channel numbers. Clears some menu entries.
Selects a channel number or
menu item.
ENTER
F4
•
Displays a menu showing additional functions for the number
keys.
For the MORE menu in TV mode,
see below.
With remote control programmed
for another device, the MORE menu
is specific to the device. See page
68.
For CEC-enabled devices, page 75
249 Series: See page 68.
The MORE menu in TV mode
Note: To operate other audio/video
devices using the TV’s remote
control:
• See Appendix A, “Programming the Remote
Control.”
• For HDMI devices compatible with the TV’s
HDMI Control feature, see Appendix B.
• 153 and 249 Series
-- See page 55 for NetCommand IR “Learning” of device keys.
-- For use of specific keys with NetCommand-controlled devices, see “Special
Operation Methods,” page 58.
Downloaded From TV-Manual.com Manuals
CC Closed Captions, page 46
VIDEO Video adjustments, page 41
AUDIO Audio adjustments, page 42
SLEEP Sleep Timer, page 25
FORMAT Picture shape (aspect ratio), page 28
MORE Clears the MORE menu.
1. Basic Setup and Operation
11
TV Controls, continued
TV Control Panel
Buttons on the control panel duplicate some keys on
the remote control.
• ACTIVITY, CH, and VOL are available when no TV
menus are displayed.
•
and ENTER are available when using TV
menus or after activating a special function.
System Reset
If the TV fails to respond to the remote control, the
control-panel buttons, or will not power on/off, perform
System Reset. Recent setting changes made before
using System Reset may be lost.
To perform System Reset, press and hold the POWER
button on the control panel for ten seconds.
Panel-Lock Release
•
•
To release the Panel Lock using the TV control
panel, press and hold the ACTIVITY button on the
control panel for ten seconds. If the TV is off, press
the POWER button to have it power on.
To activate the Panel Lock, use the Lock menu,
page 54.
The TV control panel is located
on the side.
IR Sensor
The TV’s IR (infrared) sensor
receives signals from the
remote control. Do not cover
the sensor.
POWER Indicator
POWER
Key
Off
Steady On
Slow Blinking
LED Color TV Condition
Additional Information
None
TV is powered off.
Normal operation.
Green
TV is powered on.
Normal operation.
Green
TV powered off, auto-on TV Timer
is set.
Normal operation. TV can be turned on at any time.
Red
TV may require service.
Turn off the TV and unplug the set from the AC power source. Wait one minute and then plug the set back in. See Appendix E.
If the red LED is still on, contact your dealer or a Mitsubishi
Authorized Service Center. Go to www.mitsubishi-tv.com or call
1-800-332-2119 to receive Authorized Service Center information.
Downloaded From TV-Manual.com Manuals
12
1. Basic Setup and Operation
Setting Up TV Inputs
Channel Scan for Digital Channels
If you skip this step, the TV cannot receive digital
channels.
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 21.
You must perform a channel scan to enable reception
of all available high-definition and standard-definition
digital channels. The channel scan will search for
channels available locally and save them to memory. Memorizing Channels with Channel Scan
For the ANT input
Setting Up Other Inputs
1. Connect your devices to the TV, making note of
2.
3.
4.
which TV input jack is used for each device. See
“TV Connections,” page 16, for recommendations.
Power on the devices to ensure detection.
Power on the TV.
The TV will display the New Device Found screen
for each new connection it detects Learn more
about Auto Input/Auto Output Sensing on the
opposite page.
Select the device type if the device is not recognized automatically.
To start channel memorization
1. Power on the TV.
2. Press MENU and open the Initial > Channel menu.
Start channel memorization from the Initial > Channel
menu.
3. Press ENTER to enter the menu.
4. Select Ant Air if connected to an
over-the-air antenna. Select Ant
Cable for direct cable (service
without a cable box).
5. Highlight Scan and press ENTER. Channel memorization may take up
to 15 minutes to complete.
To stop channel memorization before completion,
press CANCEL.
Use the Initial > Channel > Edit menu (page 48) for
additional channel options, such as adding or deleting
channels from memory.
Sample New Device
Found screen.
5. 153 and 249 Series. You can perform NetCom-
mand IR “learning” after selecting the device type
or at a later time when convenient. To perform now,
highlight NetCommand and press ENTER. See
“Initial NetCommand Setup,” page 57 or “Setting Up
A/V Receiver Control,” page 62.
Important Note for NetCommand IR Users
153 and 249 Series. Be sure to select the correct
device type here. Although you can change the
device type later in the Inputs > Name menu, any
“learned” NetCommand IR codes will be erased
when you make the change.
6. Press BACK to close the New Device Found screen. The TV will then display the New Device Found
screen for the next connection it finds.
Downloaded From TV-Manual.com Manuals
1. Basic Setup and Operation
13
Setting Up TV Inputs, continued
About Auto Input Sensing/
Auto Output Sensing
This TV’s Easy Connect™ Auto Input Sensing feature
detects most connections automatically. The exceptions are:
• A connection on the ANT input
• An HDMI device that is powered off. Power on
the device to ensure detection.
Auto Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connected device and automatically
switch to it.
b. Prompt you to identify the device type.
c. 153 and 249 Series. Prompt you to perform
NetCommand set-up for the device, if available.
d. Repeat these steps for any other newly detected
devices.
When You First Connect a Device
• Most Device Types. Select the device type from
the on-screen list. The device type you select here
will appear as a device icon in the Activity menu.
• A/V Receiver
-- The TV detects audio connections on the DIGITAL
AUDIO OUTPUT jack and the right (red) AVR
AUDIO OUTPUT jack.
-- For an HDMI A/V receiver, select AVR from
the list of device types if the A/V receiver is
not recognized automatically.
•
HDMI CEC Devices Compatible with the TV’s
HDMI Control Feature. Compatible CECenabled HDMI devices are often recognized automatically by the TV. HDMI Control may allow you
to control some functions of a CEC-enabled device. See Appendix B, “HDMI Control of CEC Devices.”
Downloaded From TV-Manual.com Manuals
New Device Found screen for a device with HDMI
control enabled. Select On to enable the TV’s CEC
control of the device. In some cases, as in the
example above, you will also be prompted to select a
device name.
Tips on Auto Sensing
• Choose a different name for each input.
• The antenna input (ANT) is never detected,
although you can turn off the unused antenna
input in the Inputs > Name menu.
• Change the device type displayed in the Activity
menu in the Inputs > Name menu (page 50). You
must switch to a different input before changing
the device type.
• 153 and 249 Series. Any “learned” NetCommand IR codes will be erased if you change the
device type in the Inputs > Name menu.
Reactivating Auto Sensing for an HDMI Input
When you disconnect an HDMI device, Auto Sensing is
disabled until you perform these steps.
1. Switch to any input other than the one to be disconnected.
2. Disconnect the HDMI device.
3. Delete the removed HDMI device in the Inputs >
Name menu (see “Removing an HDMI Device,”
page 77).
4. Connect the new HDMI device and the New
Device Found screen will display.
14
1. Basic Setup and Operation
Basic TV Operation
Watching Broadcast TV
Watching DVDs or Videos
TV Connected to an Antenna, Direct Cable Service,
Cable Box, Set-Top Box, or Satellite Receiver
TV Connected to a DVD Player, DVR, or VCR
1. Press ACTIVITY.
2. Press
and
to select a broadcast source. If
you named devices during Auto Input Sensing,
select an input from the Watch TV group. Note: Your TV may have only one group (Watch TV).
1. Press ACTIVITY.
2. Press
and
to select a movie source. If you
named devices during Auto Input Sensing, select
an input from the Watch Movie group.
Note: For more about the Activity menu, see page 25.
Activity menu, antenna input selected
3. Press ENTER to switch to the input.
4. Tune to a channel on the ANT input using any of
these methods.
• Enter the channel number using the number
keys on the remote control and press ENTER.
For a two-part digital channel, such as 3-1,
—
press 3 CANCEL 1 to enter a dash (separator).
• Press CHANNEL UP/CHANNEL DN (+, –) to change
channels one channel at a time.
• Press
(LAST) to switch back to the previously tuned channel.
• Antenna or Direct Cable Only. Press GUIDE to
display ChannelView channel listings, highlight
a channel number, and press ENTER to tune.
Downloaded From TV-Manual.com Manuals
Activity menu, DVD input selected
3. Press ENTER to switch to the input.
1. Basic Setup and Operation
15
Basic TV Operation, continued
Making Picture Adjustments
Other TV Features
To get the best picture under different viewing conditions, set the Picture Mode before changing other video
settings. Basic picture adjustments are described on
page 41.
•
1. Press MORE.
2. Press 8 (VIDEO).
3. Press
to display the Picture Mode adjust-
•
ment.
4. Press to select a Picture Mode using these
•
guidelines:.
Name
Brilliant
Game
Bright
Natural
When to Use
Under bright light
With gaming consoles
For most daytime viewing
For most nighttime viewing
5. Press
6.
7.
to display the name of the next adjustment you want.
Press to make the adjustment.
Press BACK to clear or just wait for the display to
clear after a few seconds of inactivity.
Additional picture adjustments are described on pages
44 and 45.
Audio Settings
•
•
•
•
•
•
Changing Audio Settings
1. Press MORE.
2. Press 9 (AUDIO).
3. Press
to display the name of the adjustment
4.
you want.
Press to change the setting.
Changing the Audio Output
To switch audio output from the internal TV speakers to a connected external sound system or headphones:
1. Press MORE.
2. Press 9 (AUDIO).
3. Press
until the Speakers option is displayed. 4.
The Speakers option will display only if an A/V
receiver connection has been detected.
Press to switch between TV and either AV
Receiver or Headphones.
Downloaded From TV-Manual.com Manuals
To set the TV Clock see page 47. Set the TV
Clock if you plan to use the TV Timer (page 47) or
ChannelView (page 26) features.
To set parental controls, see the Lock menu, page
52.
Note: 249 Series. To set parental controls for
VUDU™ service, use the VUDU Info & Settings
menu.
To change the input names that appear in the
Activity menu, see Inputs > Name options, page
50.
To program the remote control to operate other
A/V devices, see Appendix A, “Programming the
Remote Control,” page 68.
To activate Audio Lock to control an external sound
system with the TV’s remote control left in TV mode. See page 69.
To control compatible devices using HDMI CEC
control, see Appendix B, “HDMI Control of CEC
Devices,” page 75.
To view still and moving digital camera images on
the TV, see “Camera Images and Music Files,” page
31.
153 and 249 Series. To control A/V devices with
NetCommand, see chapter 5, “NetCommand IR
Control for Most Devices” on (page 55).
249 Series. See page 37 for internet video streaming with VUDU™.
Other Information
•
•
•
General Cleaning. See “Cleaning Recommendations,” page 78.
Troubleshooting, Service, and Product Support. See Appendix E, page 81.
Warranty Information. See the TV warranty on
page 92.
16
2
TV Connections
Before You Begin
Auto Input/Auto Output Sensing
Surround Sound
The TV’s Auto Sensing feature automatically recognizes
most connections and prompts you to identify the type
of device connected. See page 13 for more on Auto
Sensing.
For best surround sound audio quality, route audio or
HDMI cables from the source device directly to your TV
(for Sound Projector) or directly to your A/V receiver if
using an external sound system.
Connection Types
Use the connection types available on your input
devices that will give the best video quality. For
example, choose HDMI over component video, and
choose component video over composite video.
Picture Quality
IMPORTANT
Accessory items such as cables, adapters,
splitters, or combiners required for TV
connections are not supplied with the TV.
These items are available at most electronics
stores.
For best picture quality, route signals directly from the
input device to the TV whenever possible.
Cable Management
Install the cable tie
(supplied) in one of
the four mounting
holes on the back.
Lock the cable tie in place
by pushing the end into
the mounting hole.
Sample cable routing. Secure
the cable bundle with the
release tab facing out.
1
2
To remove the cable tie,
squeeze the side tabs and
pull out.
Downloaded From TV-Manual.com Manuals
Press the release tab to
loosen the cable tie.
17
2. TV Connections
Inputs and Outputs
Connector Panels
IR– NetCommand Output/
External Controller Input
153 and 249 series
NetCommand, page 56
External Controller Input,
page 19
AVR Audio
OUTPUT
(page 23)
HDMI
(pages 20, 23)
10
5
2
6
DIGITAL AUDIO
INPUT
(page 20)
SUBWOOFER
7 OUTPUT
(page 24)
DIGITAL
Audio
OUTPUT
(page 23)
8
RS-232C
R
AVR AUDIO OUTPUT
L
RS-232C
12
249 series
9
LAN
(Ethernet, port page 37)
13
14
3
4
Y Pb Pr
VIDEO
(component
(composite video,
video, page 20) page 22)
USBa, USBb
(power only,
page 37)
DVI/PC AUDIO
INPUT
(page 21)
Y Pb Pr
(component video,
page 20)
LAN
USBa USBb
3
249 Series. Additional ports are
located in the central recessed area.
4
VIDEO
(composite video,
page 22; with an audioonly device, page 24)
VIDEO
(composite video,
page 22)
HDMI
(page 20)
Y Pb Pr
(component video,
page 20)
2
3
4
ANT
(page 21)
1
Calibration
Microphone Input,
153 and 249 series
(page 36)
11 USB
(page 31)
Downloaded From TV-Manual.com Manuals
18
2. TV Connections
Inputs and Outputs, continued
1. ANT (Antenna)
Connect your main antenna or direct cable service (no
cable box) to ANT. The ANT input can receive digital
and analog over-the-air channels from a VHF/UHF
antenna or non-scrambled digital/analog cable source.
2. HDMI™ Inputs (High-Definition
Multimedia Interface)
The HDMI inputs support uncompressed standard and
high-definition digital video formats, PCM digital stereo
audio, and digital 5.1 surround sound. These inputs
are HDCP (High-Bandwidth Digital Copy Protection)
compliant.
Mitsubishi recommends you use category 2 HDMI
cables, also called high-speed HDMI cables, to
connect HDMI 1.3 source devices. High-speed category 2 cables bring you the full benefits of Deep Color
and x.v.Color.
The TV’s HDMI inputs are compatible with many DVI-D
and HDMI computer video signals.
Use the HDMI inputs to connect to CEA-861 HDMI
compliant devices such as a high-definition receiver
or DVD player. These inputs support 480i, 480p, 720p,
1080i, and 1080p video formats.
These HDMI inputs can also accept digital DVI video
signals. To connect a device’s DVI output to the TV’s
HDMI input, use an HDMI-to-DVI adapter or cable plus
analog audio cables. Connect the analog audio cables
to the DVI/PC INPUT AUDIO jacks on the TV to receive
left and right stereo audio from your DVI device.
3. Y Pb Pr (Component Video)
Connect devices with component video outputs to this
jack. Use the adjacent AUDIO R and L jacks if you wish
to send audio to the TV.
4. Video (Composite Video)
Connect a VCR, DVD player, standard satellite receiver,
or other A/V device to the TV. Use the adjacent AUDIO
R and L inputs if you wish to send audio to the TV.
5. AVR AUDIO OUTPUT
Use AVR AUDIO OUTPUT to send analog audio of the
current program to an analog A/V surround sound
receiver or stereo system. Digital audio from digital
channels and HDMI devices is converted to analog
audio by the TV for output on this jack. This is the only
audio connection needed to the TV if using an analog
A/V receiver or stereo system.
Headphones. These jacks can also be used for headphones that accept standard line level audio signals. An adapter may be needed.
6. DIGITAL AUDIO INPUT
This input sends digital surround sound to the TV’s
speaker array from a device, such as a DVD player,
connected to INPUT 2.
7. SUBWOOFER OUTPUT
Connect a powered subwoofer to complement Sound
Projector speaker effects.
8. DIGITAL AUDIO OUTPUT
HDMI Cable Categories
HDMI cables are available as Category 1 and Category 2
types.
• Category 2 Cables (also called high-speed HDMI
cables). Newer, HDMI 1.3-compliant DVD players,
video games, and set-top boxes require Category 2
cables, suitable for clock frequencies up to 340 MHz
or data rates of up to 10.2 gigabits per second. Use
category 2 cables for high-speed 1080p HD signals
carrying extended color encodings (i.e., 30 or more
bits, also called Deep Color). Category 2 cables are
also suitable for standard HDTV signals.
• Category 1 Cables (also called standard HDMI
cables). Category 1 cables may be unmarked. They
are suitable for standard HDTV 720p, 1080i, and
1080p signals with 8-bit color depth. Use category 1
cables for clock frequencies up to 74.25 MHz or data
rates of up to 2.23 gigabits per second.
Downloaded From TV-Manual.com Manuals
This output sends Dolby Digital or PCM digital audio
to your digital A/V surround sound receiver. Incoming analog audio is converted by the TV to PCM digital
audio. If you have a digital A/V receiver, in most cases
this is the only audio connection needed between the
TV and your A/V receiver.
9. DVI/PC AUDIO INPUT
When connecting a DVI device to one of the TV’s HDMI
inputs, use these jacks to send left and right analog
audio to the TV.
2. TV Connections
Inputs and Outputs, continued
10. IR–NetCommand Output/External
Controller Input
153 and 249 Series. Use an IR emitter cable with this
jack to send control signals to external IR remote-controlled devices. Alternatively, your professional installer
can use this jack as the input for an external controller.
Connect to this jack and when the New Device Found
screen appears, select operation of the jack as either
an input (for an external controller) or as an output (for
NetCommand IR control). See page 56.
11. USB
The TV can read JPEG photo files and mp3 music files
from a USB device.
12. RS-232C
249 Series. Use the RS-232C interface to receive
control signals from compatible home-theater control
devices. See www.mitsubishi-tv.com for a list of
control signals for this interface.
13. LAN
249 Series. Use the LAN Ethernet jack for streaming
internet video to the TV. See page 37 for setup. Visit
www.VUDU.com for details about VUDU™ service.
14. USBa, USBb
249 Series. Standard USB 5-volt, 500-milliamp power
outputs you can use to supply power to an accessory
device. For use with the VUDU wireless adapter, see
page 37.
Downloaded From TV-Manual.com Manuals
19
20
2. TV Connections
HDMI Device
Y Pb Pr Component Video Device
HDTV Cable Box, Satellite Receiver, DVD/
Blu-ray Player
HDTV Cable Box, Satellite Receiver, DVD/
Blu-ray Player
Suitable for use with Sound Projector surround
sound.
If your source device has an HDMI output, use the
connections for HDMI devices described on this page
instead of component video.
Required:
1. RCA-type component video cables
2. Audio cable(s)
2a. Digital audio cable
or
2b. Left/right analog stereo audio cables.
Note:
•
•
To hear digital surround sound from the TV’s
Sound Projector speaker array, connect the digital
audio output from the device to the TV’s DIGITAL
AUDIO INPUT jack.
To hear digital surround sound from an external
sound system, connect the digital audio output
from the device directly to your digital A/V receiver
instead of the TV.
Suitable for use with Sound Projector surround
sound
Required: HDMI-to-HDMI cable.
Connect an HDMI cable from the TV back panel to the
HDMI device output. HDMI devices provide video and
audio through the single cable. This connection sends
digital surround sound from the source device to the
TV’s speaker array.
Mitsubishi recommends you use category 2 (highspeed) HDMI cables to connect HDMI 1.3 source
devices. High-speed category 2 cables bring you the
full benefits of Deep Color and x.v.Color. See “HDMI
Cable Categories” on page 18 for more on HDMI cable
types.
R
AVR AUDIO OUTPUT
L
HDMI-to-HDMI
cable
R
AVR AUDIO OUTPUT
L
Any device with
HDMI output
TV
or
1.
Incoming from
cable service or
satellite
dish
Pr
Pb
Y
VIDEO OUT
2b.
R
L
AUDIO OUT
Pr
CABLE IN or
SATELLITE IN
2a.
Pb
Y
VIDEO OUT
R
L
DIGITAL
AUDIO OUT AUDIO OUT
Any device with
component video
output
Downloaded From TV-Manual.com Manuals
TV
21
2. TV Connections
DVI Video Device
Antenna or Cable TV Service
Connect the incoming cable to the TV’s ANT input.
Connect DVI devices (digital only) to the TV’s HDMI
input jacks.
VHF
antenna
Required:
1. DVI-to-HDMI cable or DVI/HDMI adapter and HDMI
cable
2. Left/right analog audio cables.
Some devices require connection to an analog input
first in order to view on-screen menus and to select DVI
as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.
Note: The HDMI connection supports copy protection
(HDCP).
R
Cable TV
service
UHF
antenna
Direct cable (no cable box)
Cable Box, Satellite Receiver, DVD Player
300-ohm-to75ohm combiner
(side view)
or
AVR AUDIO OUTPUT
L
or
1.
DVI OUT
TV
TV
ANALOG
AUDIO OUT
2.
Any device with DVI output
Composite Video Device
VCR or other device with composite video
output
Required:
1. Composite video cable (usually yellow)
2. Analog stereo audio cables.
R
AVR AUDIO OUTPUT
L
TV
1.
L
R
AUDIO
VCR or
COMPOSITE
other VIDEO OUT
device with
composite
R
video
AUDIO
OUT
output
L
Downloaded From TV-Manual.com Manuals
OUT
IN
Not recommeded. Other
connection types provide
better quality audio and video.
R
L
Older
cable
box
2.
22
2. TV Connections
VCR or DVD Recorder to a Cable Box
VCR or DVD Recorder to an
Antenna or Wall Outlet Cable
Required:
1. Video cables
1a. Component video cables (red/blue/green)
or
1b. Composite video cable (usually yellow)
2. Left/right analog audio cables.
3. Two-way RF splitter
4. Two coaxial cables
Note:
• Use composite video only if component video or
HDMI are unavailable. For an HDMI connection
between the TV and recorder, see page 20.
• If your recording device has an analog-only tuner,
you must use a digital converter box to enable
recording of digital broadcasts.
Required:
. Video cables
1a. Component video cables (red/blue/green)
or
1b. Composite video cable (usually yellow)
2. Left/right analog audio cables.
3. Two-way RF splitter
4. Three coaxial cables
5. Video and audio cables required to connect the TV
to the cable box.
Notes: Use composite video if only if component video
or HDMI are unavailable. For an HDMI connection between the TV and recorder, see page 20.
When using this connection configuration, it is
possible to view live cable programsAVRthrough
the
AUDIO OUTPUT
L
recording device. For best picture Rquality
always
view live cable programs directly from the TV input
connected to the cable box device.
TV
TV
5.
Audio and
video from
cable box
directly to TV
1b.
or
1b.
2.
1a.
or
1a.
2.
OUT
IN
Cable
Box
4.
COMPOSITE
VIDEO OUT
R
L
AUDIO OUT
COMPONENT
VIDEO OUT
ANTENNA
IN
COMPOSITE
VIDEO OUT
DVD Recorder or VCR
Incoming cable
3.
RF Splitter
Downloaded From TV-Manual.com Manuals
4.
4.
COMPONENT
VIDEO OUT
DVD Recorder or VCR
3.
RF Splitter
Incoming
cable
R
L
AUDIO OUT
ANTENNA
IN
4.
4.
23
2. TV Connections
A/V Receiver
A/V Receiver with HDMI Output
Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on the ANT input or devices connected directly to the TV, you must use one of the
connections shown below. Usually, only one of these connections is required.
The TV makes all audio available in digital and analog
formats:
• Analog audio coming into the TV is available as
output in digital stereo format on the DIGITAL
AUDIO OUTPUT jack.
• Digital incoming audio is available as analog output
on the AVR AUDIO OUTPUT L and R jacks.
R
Required: One HDMI-to-HDMI cable
This option allows you to view content from devices
connected to an A/V receiver over a single HDMI cable
going to the TV. The HDMI cable can transmit both
audio and video to the TV.
You can use an HDMI connection as described here
in addition to an audio connection from the TV’s audio
output. The optional audio connection allows you to
hear, through the A/V receiver, devices connected to
the TV only, e.g., an antenna on the ANT input.
You may be able to use the TV’s remote control (in
TV mode) to operate connected CEC-enabled HDMI
devices. Experiment with your equipment to determine
which functions are available to the TV’s remote control. See Appendix B, page 75.
153 and 249 Series: This setup allows you to use
NetCommand-controlled audio and video switching over
the HDMI cable. See “Case 3: Automatic Audio and
Video Switching via HDMI” on page 65.
AVR AUDIO OUTPUT
L
To use NetCommand to supplement HDMI control of a
CEC-enabled A/V receiver, note the recommendations
under “More About Using an HDMI Connection,” page 65.
TV
Stereo analog cables
(for an analog A/V
receiver)
L
or
R
Digital coaxial
cable (for a digital
A/V receiver)
OPTICAL
L
R
INPUT AUDIO
AVR AUDIO OUTPUT
L
TV
Optional
analog or
digital audio
connection
HDMI cable
COAXIAL
INPUT
A/V receiver back panel
Note:
•
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from
the TV as a digital signal. To hear these copyprotected signals through the A/V receiver, use
the connection for an analog A/V receiver.
COMPOSITE
VIDEO OUT
• Check the A/V receiver’s Owner’s Guide for
information concerning use of the digital input
R
and
AUDIOswitching between digital sound and
OUT
analog
stereo sound from the TV.
L
Downloaded From TV-Manual.com Manuals
A/V receiver with
HDMI output
HDMI OUT
L
R
ANALOG AUDIO IN
Any connection
types
High-definition
DVD player
DIGITAL
AUDIO IN
VCR
DVD player
Cable box
24
2. TV Connections
Subwoofer
Audio-Only Device
Required: Audio cable with RCA-style plug
R
Keep an unused RCA-style connector in the Y/VIDEO jack while
using an audio-only device such
as an MP3 or CD player.
AVR AUDIO OUTPUT
L
Unused
RCA-style plug
(plug in first)
TV
Audio-only
device
Y
VIDEO
R
L
Subwoofer
Downloaded From TV-Manual.com Manuals
3
Using TV Features
Selecting an Input
25
Sleep Timer
The Activity menu lets you switch TV inputs. If you
named devices during Auto Input Sensing, the inputs
are organized into groups based on possible ways to
use each device.
The Sleep Timer turns the TV off after the length of time
you set.
To set the TV to turn on at a certain time of day, see the
Initial > Timer menu on page 47.
1.
2.
3.
4.
Setting the Sleep Timer
1. Press MORE on the remote control. The TV’s MORE
menu will display.
2. Press CANCEL (SLEEP) repeatedly to increase the
time in 30-minute increments. The maximum is 120
minutes.
3. Press BACK or wait five seconds without pressing
any keys for the message to disappear.
•
•
Press the Activity key.
Use
to move through groups of TV inputs.
Use to select an input.
Press ENTER to switch to the input.
To change the list of inputs shown in each activity
group, see Inputs > Activity, page 50.
To assign or change the names of input icons, use
the Inputs > Name menu, page 50.
Viewing or Changing the Sleep Timer
1. Press MORE.
2. Press CANCEL (SLEEP).
3. Press CANCEL (SLEEP) additional times to change
the number of minutes before the TV powers off.
SLEEP
With the MORE menu displayed, press the CANCEL
key on the remote control to activate or deactivate the
Sleep feature.
Downloaded From TV-Manual.com Manuals
26
3. Using TV Features
ChannelView Channel Listings
Redirecting Audio Output
Selecting an Audio Output Device
1. Press MORE and then 9 (AUDIO).
2. Press to show the Speakers option. The Speak3.
ers option will display only if there is a recognized
audio device on an audio or HDMI output.
Press to select either AV Receiver, Headphones, or TV.
Adjusting an External Subwoofer
1. Play sample video or music containing low-freChannelView. Programs for the tuned channel are
listed on right side of screen.
ChannelView™ shows memorized channels on the ANT
input. It displays channel names and program information for digital channels as sent by broadcasters or your
local cable service provider (information may be incomplete). No program information is displayed for analog
channels.
Note: You must set the TV Clock (page 47) to receive
ChannelView listings for the current channel.
Using ChannelView
Feature
Instructions
Receive updates for a
digital channel.
1. Press
to
highlight a channel
number.
2. Press the INFO key
(the screen may
briefly go blank).
Display/hide ChannelView
listings from the ANT
input.
or
.
Scan channels quickly.
Hold PAGE UP/PAGE DN
Jump to listings for a specific channel.
1. Enter the channel
number.
2. Press ENTER.
See more of the program
description for the current
channel (if available).
INFO
Tune to the highlighted
channel.
ENTER
to
3. With Subwoofer set to On, press ENTER to display a
slider for volume.
4. Press to adjust the subwoofer volume level.
Disconnecting an Analog A/V Receiver
When you disconnect an analog A/V receiver, change
the Speakers setting to TV to hear sound from the TV
speakers. Change the setting using the remote control’s MORE > 9 (AUDIO )key or the Adjust > Audio >
Speakers menu.
Controlling A/V Receiver Volume
With a Standard TV Setup
•
•
GUIDE
Scan channels one by one. Hold
2.
quency bass sound.
Press MORE and then 9 (AUDIO). Use
display the Subwoofer option.
•
Recommended Method: Program the TV’s
remote control for your A/V receiver and enable the
Audio Lock feature. See page 69.
Program the TV’s remote control for your A/V
receiver and set the TV remote control’s mode to
AUDIO. Return the control mode to TV to control the
TV.
Use the remote control that came with the A/V
receiver.
With HDMI Control (CEC-Enabled HDMI
A/V Receiver)
The TV’s remote control may control some functions of
the A/V receiver. See Appendix B, “HDMI Control of
CEC Devices,” page 75.
With NetCommand IR Control
153 and 249 Series. Set up NetCommand control of
the A/V receiver’s volume functions in the Inputs > AVR
menu. The TV’s remote will then control A/V receiver
volume. See page 62.
Downloaded From TV-Manual.com Manuals
27
3. Using TV Features
Status Display
3
Press the INFO key to see
the on-screen status
display. The most
common displays are
shown here.
4
6
1
402-101 KABC
Monday Night Football
2
TV-PG DLSV
St. Louis vs. Tampa Bay, played in Tampa for
5
8
Sample information
from the on-screen
status display
9
10
7
Sleep 30 min
12
Tuesday 9:10 PM
HD 1080i Standard
13
Surround
English
11
14
About Channel Numbers
INFO
Channel Numbers for Over-the-Air Reception or
Reception by Direct Cable
Note: All signals are automatically converted to
1080p for display.
Standard-Definition Analog Channels
Cable Reception
2. Audio Indicator. Key:
Channel 3
Cable
3
480i Stretch
Receiving Standard-Definition
Analog Signal (480i)
Standard-Definition Digital Channels
7-1 KABC-SD
SD 4:3 Stretch
Receiving Standard-Definition
Digital Signal (SD)
High-Definition Digital Channels
Main Channel 7
Sub-Channel 1
Over-the-Air
Antenna Reception
Ant
7-1 KABC-HD
HD 16:9 Stretch
Receiving High-Definition
Digital Signal (HD)
Downloaded From TV-Manual.com Manuals
TV speakers External sound system Headphones Mute
3. Channel number (antenna source only)
Digital channel includes major and sub-channel
numbers.
4. Digital channel name (if broadcast); antenna
source only.
5.
Main Channel 7
Sub-Channel 1
Over-the-Air
Antenna Reception
Ant
1. Current Input
V-Chip rating
• Antenna source only for digital signal
• Antenna or VIDEO composite jack for analog
signal
6. Program name (if broadcast); digital source only
7. Program description (if broadcast); digital
source, antenna only. Press the INFO key additional
times to see more of the description.
8. Sleep Timer remaining time
9. Day and time
10. Signal type being received
11. Screen format in use
12. Program Audio indicator (antenna source only)
• Digital source: Stereo, Surround
• Analog source: Stereo, Stereo SAP, SAP
13. Available language (digital source, antenna only)
14.
Signal-strength indicator (digital source,
antenna only)
28
3. Using TV Features
TV Signals and Display Formats
This is a 16:9 widescreen TV suitable for images available
from HDTV and many DVDs. You can view older-style, squarish images (4:3 aspect ratio) using one of the display formats
described on this page. Press the MORE key and then the
0 key (FORMAT) to cycle through available display formats.
The TV remembers the format you last used for each input.
Original
Signal
TV
Display
Distorted. Not recommended.
Expand
Recommended for
letterbox. See
Note 1.
Distorted; not
recommended. See Note 1.
Zoom
Distorted. Not recommended. See
Note 1.
Recommended
for anamorphic
2.35:1 images. See Note 1.
Stretch
Recommended for
standard
broadcasts. See Note 1.
Distorted; not
recommended. See Note 1.
Stretch
Plus
Recommended for
standard
broadcasts. See Note 1.
Distorted; not
recommended. See Note 1.
Narrow
See Note 1
Distorted; not
recommended. See Note 1.
DVD Image Definitions
Image information may be stated on the DVD case. Some
DVDs support both formats described below.
Anamorphic (or Enhanced for WideScreen TV). Indicates
DVDs recorded to show widescreen images properly on 16:9
TV sets using the TV’s Standard format mode (recommended).
Non-Anamorphic (or 4:3, 1.33:1, Letter Box, or
Full Screen). Indicates DVDs recorded for viewing on
squarish TV screens. They may be full screen (4:3 or
1.33:1) which crops movies to fit the narrow TV, or letter
box, which adds black top and bottom bars.
Signal Definitions
480i: Older type of interlaced signals from the ANT input,
composite VIDEO, component Y Pb Pr, or HDMI jacks.
480p: Progressive-scan DVD signals on component Y Pb
Pr or HDMI jacks.
720p and 1080i: High-definition signals received through
component Y Pb Pr or HDMI jacks. These signals are
always 16:9 (widescreen).
1080p: High-definition signals from a PC or Blu-ray
player, HDMI inputs only.
SD 4:3: Standard-definition squarish-screen-format
signals from digital channels on the ANT input.
SD 16:9: Standard-definition widescreen-format signals
from digital channels on the ANT input.
HD 16:9: High-definition 16:9 widescreen signals from
digital channels on the ANT input.
TV Display Format Definitions
Standard: The full-screen format used by HDTV signals. Use this format to display anamorphic DVDs with a 1.78:1 or
1.85:1 aspect ratio. Anamorphic DVDs with a 2.35:1 aspect
ratio are displayed correctly but with top and bottom black
bars. Squarish (4:3) images are stretched evenly from side to
side. Available for all signals.
Expand: Enlarges the picture to fill the screen by cropping
the top and bottom; useful for reducing the letter box top and
bottom bars of non-anamorphic DVD images.
Zoom: Enlarges the picture to fill the screen by cropping the
sides, top, and bottom to eliminate black bars.
• 480i/480p and SD 4:3 signals: Eliminates top and
bottom bars on anamorphic DVDs with a 2.35:1 aspect
ratio.
• 720p, 1080i, SD 16:9, and HD signals: Eliminates bars
added to squarish 4:3 images.
Downloaded From TV-Manual.com Manuals
Anamorphic DVD
Non-anamorphic or SD 4:3
Standard
Recommended
Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.
Original Signal
Display Formats
SD 16:9 or
HD Digital
720p, 1080i,
1080p Signal
Wide Recommended to reExpand move side bars.
(except 720p
)
Full
Best for computer or
Native game images (component and HDMI only)
Zoom
Recommended to remove bars from the top,
bottom, and sides.
TV Display Formats. Press MORE and then 0 (FORMAT)
to see the displays available for the current program.
Press INFO to see the name of the display format in use.
Stretch: Stretches squarish 4:3 images across the screen
to display the entire image with less distortion than Standard.
Stretch Plus: Similar to Stretch, but minimizes distortion on the sides by expanding the picture to crop off
portions of the top and bottom. Use
to adjust the
vertical position of the picture.
Narrow: Displays narrow 4:3 images in their original
shape. Adds black side bars to fill the screen.
Wide Expand: Enlarges the picture, cropping the image
on both sides. Removes or reduces black side bars added
to narrow images converted to 16:9 signals for digital
broadcast.
Note: All high-definition channels send widescreen
(16:9) signals, but not all programming was created for
the widescreen format. The broadcaster may stretch
the image or add side bars to fill the widescreen area.
Full Native: Displays all pixels in the original image
29
3. Using TV Features
Using the TV with a Personal Computer
Connecting a Computer to the TV
Use one of the connection methods listed below based
on your computer’s video output.
Computer
Video Output
Digital DVI
Video Connection
DVI-to-HDMI cable
or an HDMI cable
with an HDMI-toDVI adapter
Audio
Connection
R
AVR AUDIO OUTPUT
L
Stereo audio
cables
TV
Computer with
HDMI audio and
video output
Note: If the computer’s audio output
is a single mini jack, a mini audio-toRCA-male “Y” adapter cable is also
required.
HDMI
HDMI-to-HDMI
cable
No additional
audio connection is required.
IMPORTANT
This TV accepts digital computer signals only.
An HDMI-to-HDMI connection carries all video and
audio on a single cable.
TV
1. Connect the computer’s digital signal output to one
2.
3.
4.
5.
of the TV’s HDMI jacks. See the connection diagrams for the method suited to your equipment.
Connect the computer’s audio output using one of
these options:
• For digital DVI signals, connect analog left/right
audio to the TV’s DVI/PC INPUT AUDIO jacks.
• For HDMI signals, no additional audio connection is required.
Power on the TV and computer. The TV will detect
the connection and display the New Device Found
screen.
In the New Device Found screen, press to
highlight PC in the list of device types. It is important to use the name PC so that the TV processes
the video signal correctly.
Press BACK to close the New Device Found screen.
R
HDMI-toDVI cable
AVR AUDIO OUTPUT
L
Analog audio
cables
DVI OUT
R
L
AUDIO
OUT
with DVI
and analog
A DVI connectionComputer
from a personal
computer
requires a
audio
outputs
separate audio connection.
Note: If your computer provides digital audio output (coaxial or optical), you can connect it
directly to a digital A/V receiver and bypass
the TV.
Downloaded From TV-Manual.com Manuals
30
3. Using TV Features
Using the TV with a Personal Computer
Computer Video Adjustments
Tip
Set the computer’s screen saver to display a pattern
after several minutes of inactivity. This acts as a
reminder that the TV is powered on
1. Power on the computer.
2. Select PC from the Activity menu. To do this,
3.
4.
5.
press ACTIVITY to open the Activity menu, move the
highlight to the PC icon, and press ENTER.
Working from the computer, change the resolution
of the computer image. View the computer image
on the TV and maximize the computer resolution
while maintaining a suitable aspect ratio for the
image.
Computer Display Formats
Perform TV video adjustments. Press
MORE then press 8 (VIDEO) repeatedly
Press MORE then press 0 (FORMAT) repeatedly to cycle through the
to access video-adjustment options.
TV displays available for your computer’s video signal.
Press MORE then press 0 (FORMAT)
repeatedly to find the picture format
Computer Signal
As Displayed on TV Screen
(aspect ratio) best suited to the image. 4X3
16 X 9
Original Format
Zoom
See the chart on this page showing
Standard
Standard
how different computer resolutions
can be displayed on the TV.
VGA
640 X 480
Distortion in Computer Images
Computer images may show distortion when viewed on the TV, e.g., lines
that should be straight may appear
slightly curved.
WVGA
848 X 480
SVGA
800 X 600
WSVGA
1064 X 600
Image Resolution
Your Mitsubishi TV can display the resolutions shown in the chart from standard
VGA (640 x 480) through 1920 x 1080
signals at a refresh rate of 60 Hz.
In most cases, the computer will select
the best resolution match to display on
the TV. You can override this setting if you
wish. Refer to your computer operating
system’s instructions for information on
changing the screen resolution.
You may need to restart the computer for
changes to take effect.
Original Format
XGA
1024 X 768
PC 720p
1280 X 720
WXGA
1360 X 768
SXGA
1280 X 1024
Original Format
PC 1080p
1920 X 1080
Downloaded From TV-Manual.com Manuals
Standard
Standard
Zoom
IO
3. Using TV Features
31
Camera Images and Music Files
•
•
The TV can read photo or music files from a USB
drive. Photos must be in JPEG format and music
files must be in mp3 format. To play music files
while displaying a photo slide show, see “USB
Media Setup Menu” on the next page.
The TV can display files of still or moving images
from a camera through the Y/VIDEO port.
The USB Media Player Menu
3. From the USB Menu you can:
Activate any of the
menu options
Highlight an icon and press
ENTER.
Display the Activity
menu.
Press ACTIVITY. Press again to
clear.
Display the main
menu.
Press MENU. Press again to
clear.
Display status for the
file source.
Press INFO. Press BACK to
clear.
4. To resume use of the USB port after switching the
TV to a different input, press ACTIVITY, choose View
Photos, and select the USB port.
Playing a Slide Show or Playlist
Displaying the Menu
1. Back up the data on your USB drive before con2.
necting it to the TV. Mitsubishi is not responsible
for any file damage or data loss.
Connect your USB drive to the TV’s USB port.
The USB Media Player menu displays while files
are being read. Wait until the Play icon appears
highlighted and in full color.
Use these keys while playing a slide show or playlist.
or
ENTER
Pauses a slide show or playlist.
Stops a slide show or playlist.
R
L
The TV can read photo and music files from the
USB port.
Replays the slide show or playlist.
Displays the previous or next slide.
Plays the previous or next track.
GUIDE
Rotates an image clockwise in 90˚ increments.
BACK
Displays the USB Media Player menu.
MENU
Displays the main menu and stops play.
Activity
Displays the Activity menu and stops play.
INFO
Displays slide name or track name. Press
BACK to clear.
IMPORTANT
Always stop playback with
(STOP) or change
to a different TV input before disconnecting your
USB device.
The TV can read JPEG files as created by the
camera. If you edit a picture file on a computer
and resave the image, the TV may be unable to
read the resaved file.
Downloaded From TV-Manual.com Manuals
AVR AUDIO OUTPUT
L
32
3. Using TV Features
Camera Images and Music Files, continued
Thumbnail and Playlist
Menus
JPEG Thumbnail Menu
Use these keys while viewing JPEG thumbnail images
or the music tracks in a playlist.
Moves the highlight from item to item.
GUIDE
Rotates a thumbnail clockwise in 90˚
increments
or
ENTER
Plays the slide show or playlist starting
with the highlighted item.
Selects the last item on the current page.
Selects the first item on the current page.
Displays the next or previous page of
PAGE UP/DN items.
BACK
Displays the USB Media Player menu.
MENU
Displays the main menu.
Activity
Displays the Activity menu.
Picture Files Compatible with the USB Port
• Still images recorded on digital cameras using the
Exchangeable Image File Format, version 2.1 (EXIF
2.1) standard for digital still cameras and Design
Rules for Camera File Systems version 1.0 (DCF 1.0)
• Some images opened and resaved on a computer
may not play back or may not display in the thumbnail list. This happens if the files were resaved in an
incompatible format.
• Full path file names can be no longer than 50 characters and must end in a .jpg extension. Only the
first 20 of the 50 characters will display.
Downloaded From TV-Manual.com Manuals
USB Media Setup Menu
Use the USB Media Setup menu set up play of a slide
show or playlist.
• If JPEG image files and mp3 files are on the USB
device, choose:
-- Slideshow + Music
-- Slideshow
-- Music only
• Slideshow. Select either Auto or Manual advance
for the slide show. During manual operation, press
ENTER to advance to the next slide.
• Interval. For automatic advance, select the time
interval for display of each slide. The interval you
select here is the minimum time between slides;
actual time may be longer for larger files.
• Frequency. For automatic advance, select the
number of times (frequency) to play the complete slide
show and/or playlist: Once, Twice, or Continuous.
• Press BACK to close the Media Setup menu and
return to the Media Player menu.
Notes on Using the USB Port
• The TV ignores all commands while reading files. Wait
until the Play icon appears highlighted and in full
color before continuing.
• Large files or high-capacity storage devices may take a
long time to display.
• The TV can read files up to 10 MB in size with a
maximum of 2,500 files stored on the device. The
FAT16 or FAT32 file system is recommended.
• Use a USB drive instead of a card reader.
• Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible
for any file damage or data loss.
• Some manufacturers’ devices may be incompatible with the TV. If the TV is unable to display your
photos, you can:
-- Transfer files to a different USB drive.
-- Use your digital camera’s composite video
output. See page 33.
O
3. Using TV Features
33
4. When the New Device Found screen displays,
Photos and Moving Video
as Composite Video
Connect the camera to the TV using a composite video
cable if:
• You are unable to see images using the USB port.
• You wish to view moving video from the camera.
5.
6.
assign the name Camcorder.
Press BACK to close the New Device Found screen.
Press ACTIVITY, select Watch Movie > Cam, and
press ENTER.
Control the slide show or movie through the camera as
the TV’s USB Media Player menu will be unavailable. The display resolution will be standard-definition (480i).
1. Refer to the owner’s manual supplied with the
2.
3.
camera for instructions needed for this setup.
Set the camera’s output signal type to NTSC and
put the camera into playback mode.
With the camera still turned on, connect your digital
camera’s composite video cable (usually yellow) to
the TV’s Y/VIDEO jack. To hear audio, connect the
camera’s audio output cable to the AUDIO L jack.
Optional
Audio Cable
L
Camera connection using a composite video cable
Downloaded From TV-Manual.com Manuals
7. If viewing photos, advance through the images
manually or set the camera to advance automatically.
34
3. Using TV Features
Sound Projector
Sound Projector Technology
Connecting the TV
The TV’s bank of speakers can be adjusted to reflect
sound off the room walls to create a surround sound
effect.
To get the full benefit of the TV’s Sound Projector, the
TV must be connected to a source input providing
digital surround sound. The TV can receive digital surround sound on:
• Any HDMI jack
• The DIGITAL AUDIO INPUT jack (when used in
conjunction with INPUT 2)
• The ANT input (from some digital broadcasts)
Setup can be performed manually and/or automatically,
depending on your TV model:
•
•
Manual setup only
151 series
Manual or Auto setup
153 and 249 series
To create the surround sound effect, the room walls
must reflect sound and not be covered with soundabsorbent material.
Repeat the setup procedure if you reconfigure the
room’s walls or furnishings.
Before You Begin
Positioning the TV
•
•
See page 20 for suggestions on connecting your
devices.
Basic Setup
Note: 153 and 249 Series. If you have already performed Auto setup, any manual adjustments will
erase all settings created during Auto setup.
1. Press MENU and go to Initial > SoundPro. Press
ENTER to enter the menu.
Center the seating area in front of the TV and at
least six feet away from it.
Arrangements that give good results:
2. Enter the room dimensions and layout information
requested in the screen. To change measurements, press
.
•
If the room is an odd shape, locate the TV to take
best advantage of wall reflections.
3. Press MENU to exit.
4. Play some sample audio to check sound quality. If further adjustment is needed, use the Custom
menu as described below.
•
Avoid locations that may distort sound reflections.
Custom Menu
Use the Custom menu after defining the room layout.
For a room with large areas of curtains that might affect
sound reflection, do the following:
a. Open the curtains fully to improve sound reflection.
b. Set angles by performing the procedure in
“Adjusting Beam Angles.”
Downloaded From TV-Manual.com Manuals
3. Using TV Features
35
Sound Projector, continued
c. Close the curtains.
d. Set levels by performing the procedure in
“Adjusting Levels.”
1. From the Initial > SoundPro menu go to the
2.
Custom menu.
Position yourself in your usual viewing location. Remain in this position, looking at the TV, while
making the following adjustments.
How to Make Adjustments in the Custom Menu
• Press
to select an audio beam; colors of the
adjusters correspond to audio beams in the onscreen diagram.
• Press to redirect the audio beam or change
the sound level.
3. Adjusting Beam Angles
a. Adjust Center Beam Angle until sound is
about equal in both ears.
b. Adjust Left Beam Angle to maximize sound
heard from the front left side.
c. Adjust Right Beam Angle to maximize sound
heard from the front right side.
d. Adjust Left Surround Beam Angle to where
the sound seems to come from the left rear
side. If this cannot be achieved, make the
setting the same as that for Left Beam Angle.
e. Adjust Right Surround Beam Angle to where
the sound seems to come from the right rear
side. If this cannot be achieved, make the
setting the same as that for Right Beam Angle.
Controls in the SoundPro
> Custom menu adjust the
direction and focus of the TV’s sound output.
At extreme beam angles, adjustment may be
limited and the image on screen may not accurately
represent the sound beams.
4. Adjusting Levels
a. Adjust Center Level to the mid level.
b. Adjust the following levels one at a time so that
each one sounds about the same as the center
level:
Left Level
Right Level
Left Surround Level
Right Surround Level
c. Check all sound levels by quickly switching
between them using
.
d. Readjust individual levels in small increments
and recheck as above until all sound levels
seem about the same.
5. Adjusting an External Subwoofer
a. Play sample video or music containing lowfrequency bass sound.
b. Press MORE and then 9 (AUDIO). Use
to
display the Subwoofer option.
c. With Subwoofer set to On, press ENTER to
display a slider for the volume.
d. Press to adjust the subwoofer volume.
Downloaded From TV-Manual.com Manuals
Adjust the volume level of individual audio beams
using sliders in the SoundPro > Custom menu.
Resetting Angle and Level Values in the Custom
Menu
1. Press BACK to clear all menus.
2. Press MENU. Go to the Initial > SoundPro menu
and press ENTER.
Change any setting (e.g., TV Location).
Press BACK to clear all menus.
3.
4.
5. Press MENU. Go to the Initial > SoundPro menu
6.
7.
and press ENTER.
Enter the correct values for the room layout.
Return to the Custom menu to adjust angles and
levels.
36
3. Using TV Features
Sound Projector, continued
Auto Setup
153 and 249 Series
Auto setup uses a calibration microphone to optimize
Sound Projector performance for most room conditions. If the room is very large or has many obstacles
affecting the sound beams, you may wish to try manual
setup, which is done without the microphone.
Initial Preparation
1. Position and connect the TV as described under
2.
3.
“Before You Begin,” page 34.
Power on the TV and external subwoofer, if any.
Plug the microphone cable into the TV’s INPUT 3
left audio jack.
Microphone Placement
• Make sure there are no large obstacles between
the TV and microphone.
• Place the microphone
-- On a flat, level surface at least six feet away
from the front of the TV.
-- On a tripod or on the backrest of your
seating.
-- At the same height yours ears would be
when watching TV. The height must be
within 3 vertical feet of the height of the TV’s
speaker array.
-- Centered in front of the TV, not off to the
side.
TV
6 ft. minimum
4. Place the microphone as described in the guidelines on this page.
Start Auto Setup
1. Press MENU and go to Initial > SoundPro.
Microphone
Set the microphone
on a level surface at
ear height at least
six feet from the TV.
Use a seat backrest
or tripod so as to
pick up sound from
all directions.
Maximum height above speakers
2. Press ENTER. Set Mode to Auto.
Height of TV
speakers
3 ft.
Be sure the
height of the
microphone is
within three feet
of the speaker
height.
3. Highlight START and press
ENTER.
5. Quietly exit the room right away. The calibration
6.
7.
sequence will start in a few seconds and may be
loud. It is important to leave the room as your presence will interfere with the calibration process.
Wait for completion of setup before returning to the
room.
Play some sample audio material to check the
sound quality.
Note: Do not perform manual adjustments after running Auto setup, as doing so will erase all settings defined during Auto setup.
8. Store the microphone out of direct sunlight and
away from heat.
Downloaded From TV-Manual.com Manuals
Microphone
Center the microphone in front of
the TV.
37
3. Using TV Features
Streaming Internet Movies with VUDU
249 Series. This TV’s built-in VUDU™ capabilities
allow you to access your own personal home video
store right on your TV. VUDU’s service offers you:
• The largest on-demand HD movie selection anywhere, featuring full 1080p and 5.1 surround sound.
• All of Hollywood’s latest hits and classics. Movies
are available to rent or buy the same day the movie
comes out on DVD.
• VUDU allows you to enjoy movies with no store
visits, no mailing, no late fees and no subscriptions.
• Parental controls allow you to restrict access to
content according to MPAA ratings. See the VUDU
Info & Settings menu.
• VUDU features popular internet applications like
Pandora, Picasa, and many others.
Visit www.VUDU.com to learn more about available
titles, prices, recommended bandwidth, and services
offered. At the time of this writing, VUDU requires an
internet bandwidth of 4.0 Mbps or higher for instant
HD video and 2.0 Mbps or higher for instant SD video. These specifications are subject to change. For a list of
recommended routers and switches, see the Support >
FAQ section at VUDU.com.
Standard Connection
VUDU Wireless Kit
Connect the TV to your network router or directly to a
high-speed internet modem using an Ethernet cable
(not supplied).
The VUDU wireless kit is available for purchase from
VUDU.com. The kit includes the two wireless boxes,
two power cables, and two Ethernet cables shown in
the diagram below. VUDU capabilities are built right
into the TV, so connect VUDU Wireless Box 2 directly to
the TV as shown.
• The LED indicators for POWER and ETHERNET will
light up once power is applied to the boxes.
• After a few seconds, the LED indicator for
WIRELESS will start to blink, indicating the wireless
adapters have been set up successfully.
• The LED indicators for WIRELESS and ETHERNET
will blink when data is being transmitted.
Router or modem
providing high-speed
internet service
Ethernet
cable
LAN
USBa USBb
Required for VUDU Service
• Broadband internet service
• Ethernet cable or the VUDU wireless kit.
• Computer access to the VUDU.com website
(required for one-time account activation).
• A credit card for rental and purchase transactions.
AC-to-DC
power
cable
TV
Standard VUDU connection via Ethernet
LAN
USBa USBb
Ethernet
cable
VUDU
Wireless
Box 1
Router
or modem
Ethernet
cable
VUDU
Wireless
Box 2
USB-to-DC
power
cable
Connecting the VUDU wireless kit. Connect VUDU
Wireless Box 2 directly to the TV.
Downloaded From TV-Manual.com Manuals
38
3. Using TV Features
Streaming Internet Movies with VUDU, continued
Getting Started
1. To start using VUDU, connect your TV to the inter2.
3.
Troubleshooting
If the VUDU Screen Is Not Responding
Press MORE and then 2 (RESET) to reset VUDU. This
resets VUDU only and does not affect TV settings.
net as described in the previous section.
Power on the TV.
Press ACTIVITY to display the Activity menu.
If You Are Unable to Connect to VUDU
• Check all power and data connections.
• If you can reach the internet with a computer or
other device on the same internet service used by
the TV, consult the router or modem owner’s guide
for reset instructions.
• If you cannot reach the internet, contact your
service provider. You may be asked for network
information such as the TV’s IP address. Press the
MORE key and then press 1 (NETWORK).
4. In the Watch Movie activity, highlight the VUDU
5.
6.
icon and press ENTER.
Browse the VUDU catalog and offerings.
When you are ready to rent or buy a movie, you
will be prompted to activate your VUDU account. Follow the on-screen instructions and use a computer to go to www.VUDU.com/activation. A
credit card is required for activation.
For Further Assistance
• If you are having trouble connecting your TV or
accessing internet applications, contact Mitsubishi
Customer Care at 1-800-332-2119.
• If you are having difficulty with your VUDU
account, contact VUDU Customer Care at
www.VUDU.com/support.
• See more troubleshooting tips in the TV Reset
Comparison Guide starting on page 81.
Once your account is activated, you can rent and buy
movies using only the TV and the TV’s remote control.
Using VUDU
ACTIVITY
Navigate VUDU’s menus with the keys on the TV’s remote control. Browse the movie catalog,
watch movie previews, set parental controls, and rent or buy movies.
To exit VUDU, press ACTIVITY and
select a different TV input.
•
•
ACTIVITY
GUIDE
BACK
VUDU PLUS. Displays more options for
the current selection (if available).
PAGE UP/PAGE DOWN
Jumps to the previous/next page
of menu items.
Returns to the VUDU home menu
while in VUDU.
PLAY/PAUSE
Starts or pauses video playback.
FAST FORWARD/REVERSE
• Press to search scenes forward
or back.
• Press additional times to speed
up search.
• Press opposite key to slow and
pause search.
STOP
Stops video playback and returns to the
previous menu.
Downloaded From TV-Manual.com Manuals
Goes to the previous screen.
Stops video playback and returns to the
previous menu.
•
•
ENTER
ON
DEMAND
FAV
Selects a menu item.
Pauses video and displays a sceneselection strip for frame-by-frame
search. Press again to resume play.
Directional navigation
Displays the TV’s MORE menu with
these special VUDU options:
F1
F2
F3
F4
Displays network information useful
for troubleshooting.
Resets VUDU if VUDU stops
responding to commands.
39
3. Using TV Features
Introduction to Home-Theater Control
This summary offers some examples of control methods available using the TV’s remote control. You may wish to
use one or more of these methods in your home theater after completing Auto Input Sensing.
Source device connected directly to the TV
Remote Control Programming (Any Connection Type)
Program the remote control to operate the A/V device. To control the device, set
the remote control to the correct mode for the device type. See Appendix A, “Programming the Remote Control.” In the case of an A/V receiver, use the Audio Lock
feature, page 69.
CEC-Enabled HDMI Device (HDMI Connection Only)
See Appendix B, “HDMI Control of CEC Devices,” page 75.
153 and 249 Series: NetCommand IR Control (Any Connection Type)
Set up NetCommand IR control of the device’s keys as desired. See “IR Emitter
Placement,” page 56, and “Initial NetCommand Setup,” page 57.
Any Connection Type
A/V
Device
TV
HDMI
Cable
CEC-Enabled
A/V Device
TV
Any Connection Type
A/V
Device
TV
Source device connected to an A/V receiver connected to the TV
CEC-Enabled
Source Device
CEC-Enabled HDMI A/V Receiver
The TV’s remote control may operate some functions of a connected A/V device. You can switch to the device by selecting its icon in the TV’s Activity menu. See
Appendix B, “HDMI Control of CEC Devices,” page 75.
HDMI
Cable
A/V Receiver
TV
153 and 249 Series: A/V Receiver with HDMI Output (no CEC)
1. Set up NetCommand IR control of the A/V receiver’s keys as desired. See “IR
Emitter Placement,” page 56, and “Setting Up A/V Receiver Control,” page 62.
2. Set up NetCommand IR control of the source device’s keys as desired. See
“NetCommand Control of a Device Connected to an HDMI A/V Receiver,” page
66.
Downloaded From TV-Manual.com Manuals
Source
Device
HDMI
Cable
Any Connection Type
A/V Receiver
HDMI
Cable
TV
40
4
TV Menus
Main Menu
Press MENU on the remote control to open the main menu and then select from one of these categories.
Adjust
Customize picture and sound settings.
41
Captions
Turn closed captions on and off; customize caption displays.
46
Initial
Perform basic TV setup. Set language, scan (memorize) channels and edit
channel options, set the TV clock, set Energy Mode, set auto-on TV Timer, set up
Sound Projector.
47
Input
Assign names to TV inputs, enable HDMI Control, assign activities to inputs.
153 and 249 Series. Perform NetCommand IR “learning.”
50
Lock
Restrict TV use. Disable the control-panel buttons. Set a pass code.
52
Menu Navigation
Displays or clears the main menu.
•
•
Moves navigation into the
options area.
Selects an item.
•
•
Moves up one menu level.
Clears the current menu.
Moves the highlight within menus.
Makes adjustments in some
menus.
Look for the key guide at
the bottom of each menu.
Downloaded From TV-Manual.com Manuals
4. TV Menus
41
Adjust
Picture
Picture
Mode
Assign names to TV inputs before making
video adjustments (New Device Found or
Inputs > Name menu). Adjustments will be
reset to the defaults if you name or rename
inputs afterwards. To make picture adjustments:
• From the Adjust > Picture menu:
1. Press
to highlight an option.
2. Press to adjust.
While watching TV: Press the MORE key and then
8 (VIDEO) in the on-screen menu. Press
to
select the video option you want to change. Press
to change settings.
Note: Changing Picture settings from the default values used in Home mode may increase energy
use above ENERGY STAR® guidelines.
Brilliant
For use under bright light; unavailable when the current
input is named Game or PC. When Picture Mode is Brilliant, energy use is greater than ENERGY STAR® guidelines.
Game
Optimizes picture and video processing for gaming
consoles. Available only when the name of the input is
Game or PC.
Bright
For most daytime viewing and x.v.Color sources
Natural
For most nighttime viewing and x.v.Color sources
Special
Advanced Picture Modes. Contact your professional installer for setup or see page 45.
151, 153 series: Special/ADV
249 series: ISF Day/ADV1, ISF Night/ADV2
ISF Day,
ISF Night
Contrast
•
•
•
•
Low contrast shows a variety of shades in darker images
In most home lighting situations, medium contrast looks best.
High contrast shows darker images more uniformly black and
makes colors appear more vibrant. High contrast is good for
brightly lit environments.
Set the Picture Mode first
before changing other video
settings, as some settings are
stored independently for each
Picture Mode. Use Picture
Modes to get the best image
under different viewing conditions.
Adjusts the white-to-black level
Settings are stored independently for each Picture Mode.
Brightness
Adjusts overall picture brightness. Settings are stored independently for each Picture Mode.
Color
Adjusts overall color intensity from no color to fully saturated.
Tint
Adjusts the red-to-green ratio.
Sharpness
Adjusts picture detail and clarity.
High
Color
Temp
Gives white images a cool cast. May provide the most
realistic picture under bright lighting.
Low
Gives white images a warm cast. Natural/Color Temp
at the low setting displays video at approximately the
6500K industry standard for NTSC pictures.
Video
Noise
High,
Medium,
Low, Off
Reduces minor noise (graininess) in the picture. Saved by input. This adjustment is not
available if the current input is named PC or Game.
Use High with poor-quality signals. Use Medium for moderate noise reduction. Use Low
with good-quality signals. Use Off to leave the picture unaltered.
On, Off
SharpEdge™ adds special edge enhancements to make the image appear sharper. Saved by input.
On, Off
153, 249 Series. DeepField™ Imager dynamically enhances black levels in portions of
the screen to provide strong contrast with detail over mixed screen content.
Demo
For comparison, displays a split picture to show On (right side) and Off (left side).
SharpEdge
DeepField
Imager
Backlight
Adjusts the white balance. Settings are stored independently for each Picture Mode.
Adjusts peak brightness of the backlight. Press ENTER to turn off the backlight.
Downloaded From TV-Manual.com Manuals
42
4. TV Menus
Adjust, continued
Audio
To make audio adjustments:
• From the Adjust > Audio menu:
1. Press
to highlight an option
2. Press to adjust.
Speakers
Subwoofer
•
While watching TV: Press the MORE key and then
9 (AUDIO) in the on-screen menu. Press
to
select the audio option you want to change. Press
to change settings.
The Speakers option displays only if an A/V receiver or headphone connection has been
detected. Detection occurs on the right AVR AUDIO OUTPUT jack or the DIGITAL AUDIO OUT jack. An A/V receiver can also be detected on an HDMI jack.
TV
Turns on the internal TV speakers.
AV Receiver
Turns off the TV speakers so you hear sound only from a connected A/V receiver.
Note: When you disconnect an analog A/V receiver, be sure to change the
Speakers setting to TV to hear sound from the TV speakers.
Headphones
Turns off the TV speakers so you hear sound only from connected headphones. See page 18. This option is not available if DIGITAL AUDIO OUTPUT is connected.
Off, On
The Subwoofer option displays only if a subwoofer connection has been identified on the SUBWOOFER OUTPUT jack. The setting you select is applied to all TV
inputs.
Use Off to turn off audio to a connected subwoofer.
[Subwoofer
level adjustment]
To adjust the subwoofer volume level, highlight Subwoofer and press ENTER to
display an adjustment slider.
Bass
Controls volume of low-pitched sound from the TV speakers.
Treble
Controls volume of high-pitched sound from the TV speakers.
Balance
Controls audio balance between the left and right TV speakers; available only when Sound Mode
is Stereo.
Sound Mode
Stereo
No special audio effects from the TV speakers; monaural programs are played as
mono, stereo and surround sound are played as stereo.
Surround
•
•
Programs with surround sound are played with Sound Projector surround
sound.
Other audio is modified:
-- For monaural (non-stereo) programs, creates a simulated stereo effect.
-- For stereo programs, creates a simulated surround sound effect.
Music
153 and 249 Series. Optimizes Sound Projector speakers for music listening.
Night
Directs sound to a specific area to lessen the disturbance to others outside the
room. Settings are reset to the default when you power down the TV.
1. Position yourself in the seating area.
2. Press ENTER to display an adjustment slider.
3. Press to adjust the direction of the sound beams until sound seems the
loudest.
Downloaded From TV-Manual.com Manuals
4. TV Menus
43
Adjust, continued
Audio, continued
Listen To
Applies only to
analog channels from the
ANT input
Language
Stereo
The TV plays stereo broadcasts in stereo and mono broadcasts in mono. The
word Stereo is displayed when you tune to a channel broadcasting in stereo.
Mono
Reduces background noise. Use when receiving a weak stereo audio signal. All
audio is played as mono with this setting.
SAP
(Second
Audio
Program)
Selects an additional monaural sound track not audible during normal TV viewing. The SAP signal might be related to the program (such as a sound track in a foreign
language), or it might be unrelated (such as a weather report). If an SAP signal is
broadcast, the letters SAP are displayed when you tune to the channel.
Selects the current language for a digital program from the ANT input. Each digital program may
include from zero to seven language choices.
Applies only to digital channels from the ANT input.
Level Sound
On, Off
Downloaded From TV-Manual.com Manuals
Reduces differences in sound volume between programming segments, such as
the difference between regular broadcast programs and commercial segments.
44
4. TV Menus
Adjust, continued
Reset
•
•
Global
Resets audio and picture adjustments for the current input. Highlight the Reset icon and press
ENTER twice.
Reset has no effect on global settings (Balance, Listen To, Language, Film Mode, and
Advanced Picture).
Global settings apply to all inputs.
Video Mute
(non-antenna
inputs only)
Screensaver
On
Displays a solid colored background when there is no video signal
from the current input. The colored screen reminds you that the
TV is powered on when there is no picture. The TV will power off
after five minutes without receiving a video signal.
Off
The screen appears black when there is no video signal from the
current input.
On, Off
Select On to display a random pattern while playing an audio-only
input. To use this feature, the input must be either
•
•
Named as an audio source (e.g., CD or MP3 Player)
or
Be the ANT input.
Film Mode
(480i and 1080i
signals only)
Auto, Off
In Auto, the TV automatically detects and applies film-decoding correction to movies filmed at 24 frames per second. Try the Off setting
if images show many jagged edges.
Smooth 120 Film
Motion
(151 series)
Standard,
High, Off
•
•
•
Smooth 120 Film
Motion
(153 and 249 series)
Blue Glow
(249 series)
Test Picture
Downloaded From TV-Manual.com Manuals
Standard: Removes judder (image vibration) and smooths
motion scenes in film-based content such as movies.
High: Removes more judder in motion scenes in movies.
Off: Use this setting if Standard or High create image noise.
Removes judder (image vibration) and smooths motion scenes in
film-based content such as movies.
1. Highlight the icon and press ENTER to display an adjustment
screen.
2. Press
to change the amount of correction or set to zero to
turn off the correction.
3. Press BACK to return to normal TV viewing.
On, Off
Select On to see blue accent lighting when the TV is powered on.
Displays a test picture for use by TV servicers. Press any key on the remote
control to clear the test picture.
4. TV Menus
45
Adjust, continued
Picture+
PerfectColor
PerfectColor Sliders
Adjusts the saturation (intensity) of six colors for
the current image source.
PerfectTint Sliders
(153 or 249 series)
Adjusts six hues for the current image source
Using PerfectColor:
Highlight the PerfectColor™ icon and press ENTER to display the PerfectColor menu. Settings are
retained independently for each TV input.
• Press
to move from one color bar to the next.
• Press to change settings.
• Press CANCEL to restore default settings.
• Press MENU to return to the main menu.
Using PerfecTint (153 or 249 Series):
To switch between PerfectColor™ and PerfecTint™ adjustments, highlight Adjust Mode and press
.
Advanced
Picture
Advanced Picture allows you to save highly customized picture
adjustments for each input. Mitsubishi recommends these
adjustments be made by a professional installer.
1. Press MENU. Under Picture+, highlight the Advanced Picture icon and press ENTER.
2. With Picture Mode highlighted, press ENTER to change from blank (undefined) to ADV.
249 Series: Choose ADV1 (daytime settings) or ADV2 (nighttime settings)
3. Use
to highlight an option you wish to change and press ENTER to see the adjustment display.
Sample adjustment display for Advanced
Picture options
4. Press to change settings.
5. Use
to navigate to additional options and press to change settings.
6. Press MENU to return to the Advanced Picture menu. The Advanced Picture adjustments will
be in effect for the current input.
To use the custom Picture Mode at a later time
Press MENU and go to Adjust > Picture > Picture Mode and:
151 or 153 Series
•
•
Select SPECIAL if settings were saved by
your professional installer.
Otherwise select ADV.
249 Series
•
•
Select ISF Day or ISF Night if settings were
saved by your professional installer.
Otherwise select ADV1 or ADV2.
To return to the default values for Advanced Picture
Display the Picture+ > Advanced Picture menu and:
151 or 153 Series
249 Series
Highlight RESET Pic Mode and press ENTER.
1. Highlight the Advanced Picture mode to change.
2. Highlight RESET Pic Mode and press ENTER. Perform this step individually for both ADV1 and
ADV2.
Downloaded From TV-Manual.com Manuals
46
4. TV Menus
Captions
Captions on Analog Channels
The TV can decode captions from the ANT input and
the composite VIDEO jacks. Broadcasters can send
either standard closed captions or text service. Standard
closed captions follow the dialogue of the program and
display in a small section of the screen. Text-service closed
captions often contain information such as weather or
news and cover a large portion of the screen.
•
•
•
Captions on Digital Channels
The TV can decode captions from the ANT input only. Broadcasters can send up to six different captioning
selections or can send analog captions for a program that
originated in analog format. A TV station may broadcast
only one or two types of captions or none at all.
Services
Digital
IMPORTANT
Analog text-service options display a large
black or gray box on the screen when no
signal is being broadcast.
The content of captions is determined by the
broadcaster. If captions show strange characters, misspellings, or odd grammar, it is not
a malfunction of the TV.
Closed-caption signals are not available through
HDMI or component jacks. See the menus for
devices connected to these inputs for closedcaption decoding.
Note:
249 Series. The TV’s Captions menu does
not control closed captions for content received
from the VUDU™ internet service.
On if Mute
Caption 1–
Caption 6
Off
•
On if Mute
CC 1–CC 4
Text 1–Text 4
Off
•
Analog Background
Gray, Black
Selects either a gray or black text background to make analog
closed captions easier to read.
Effects
Font
Default
Font 1–Font 7
(for captions
from digital
channels)
Default changes settings to those selected by the captions provider, or, if none, to the TV’s own caption defaults. Use Fonts 1
through 7 to give captions on digital channels a custom appearance.
Font Size
Large
Medium
Small
Large is the recommended size.
Font Color
White, Black, Magenta, etc.
Font Opacity
Translucent, Opaque, Flashing,
Transparent
Background
Color
White, Black, Magenta, etc.
Background
Opacity
Translucent, Opaque, Flashing,
Transparent
Analog
Downloaded From TV-Manual.com Manuals
•
•
•
On if Mute: Displays digital closed-caption signal Caption 1
when audio from the TV speakers is muted. When watching
TV, press MUTE to turn closed captions on/off.
Caption 1–Caption 6: Caption signals sent by the broadcaster
On if Mute: Displays analog closed captions signal CC 1
when audio from the TV speakers is muted. When watching
TV, press MUTE to turn captions on/off.
CC 1–CC 4: Standard closed-caption signals
Text 1–Text 4: Text-service signals
Guidelines for setting digital captions:
• A white font on a black translucent
background makes an easy-to-read
combination.
• Use contrasting colors for captions and
background.
47
4. TV Menus
Initial
Language
Clock
English
Spanish
Displays on-screen menus in either English or Spanish.
Note: To listen to audio in other languages (when available), see Adjust > Audio >
Listen To > SAP (analog signal) or Language (digital signal) on page 43.
Set the TV clock to:
• Use the TV Timer to power on the TV automatically at a preset time
• Receive correct updates to ChannelView listings
Note: When the Daylight Savings Time change occurs, you must open this menu and set the TV’s
clock ahead or back.
Time
1. With the hour highlighted, press
to change the hour and the AM/PM indicator. Press and hold to change the hour display quickly.
2. Press ENTER to set the hour.
3. With the minutes highlighted, press
to change the minutes. Press and hold to
change the minutes display quickly.
Date
1. With the month highlighted, press
2. With the day highlighted, press
3. With the year highlighted, press
Time Zone
Timer
to select. Press ENTER to set.
to select. Press ENTER to set.
to select the current year.
Eastern, Central, Mountain, Pacific, etc. The correct time zone is required for accurate
ChannelView updates.
DST
On, Off
Timer
On, Off
Daylight Savings Time. Select the setting for your area. The
correct DST setting is required for accurate ChannelView updates.
Select On to enable the Timer.
The Timer tells the TV to power on automatically at a time you set. Use this menu to set a day, time,
input, and channel for the Timer. If the TV is already on at the requested time, the TV will automatically change to the designated channel or input.
• The TV clock must be set before you can use the Timer feature.
• To remind you that the TV Timer has been set, the POWER indicator on the front of the TV flashes
slowly while the TV is powered off.
• When the Timer turns on the TV, press any key on the remote control to keep it on. Otherwise,
the TV will turn off after five minutes.
Day
Daily, Mon-Fri, (every) Sunday, (every) Monday, (every) Tuesday, etc.
Select the day or days of the week for the Timer to turn on the TV.
Time
To set the time for the TV to come on:
4. With the hour highlighted, press
repeatedly to change the hour and the AM/
PM indicator. Press and hold to change the hour display quickly.
5. Press ENTER to highlight the minutes.
6. Press
to change the minutes. Press and hold to change the minutes display quickly.
Input
Ant, DVD, VCR, etc.
Select the input you want displayed when the TV comes on. Choose from the defined
and enabled inputs that appear in the Activity menu.
Channel
If the source is the ANT input, select a channel number by pressing
hold to scroll through channels.
Downloaded From TV-Manual.com Manuals
or press and
48
4. TV Menus
Initial, continued
Channel
Ant Air,
Ant Cable
Scan
(Channel
Management)
Edit
You must perform a channel scan to receive digital channels. Scan searches for broadcast channels and adds them to TV memory. To start channel scan:
1. Highlight one of the input selections based on your connection to the ANT input:
• Air when connected to an indoor or outdoor antenna.
• Cable when connected to direct cable (no cable box)
2. Press to highlight SCAN.
3. Press ENTER to start channel memorization.
After channel scan, Edit lets you add and delete memorized channels.
• Press PAGE DN/UP to jump to the next or previous page of channel numbers.
• Press
to move through all channel numbers, one at a time.
Notes on Scan and channel memorization
• Channel memorization may take up to 15 minutes
to complete.
• To stop channel memorization before completion,
press CANCEL. Channels already added are retained.
• When watching TV, press CH
to move through
memorized channels.
• To add a digital channel that does not appear in the
Edit menu without repeating channel memorization:
1. Look up the physical channel number for
the new digital channel. See the website
www.antennaweb.org for help.
2. Press ACTIVITY and select the Ant input.
3. Use the number keys and CANCEL key to enter
the physical channel number followed by “-1”
and ENTER. For example, for physical channel
36, press
1 ENTER.
3 6 The TV will search for a digital channel on the channel
36 frequency. When it finds the channel, it will:
a. Add the channel to memory.
b. Change the channel number to the virtual
channel number sent by the broadcaster.
c. Add to memory any associated subchannels.
• Rememorize channels if you move the TV to a different geographic area with a different channel line-up.
Adding/Deleting Channels Using the Channel Edit Menu
• Channels marked with a check are in memory.
• To add or delete a channel from memory, highlight the channel number and press ENTER.
• To add a single digital channel not in the list, see the notes under Scan on this page.
• Digital channels are listed by virtual channel number with the physical channel number shown in small gray text. See below for an explanation of these terms.
-- Virtual Channel Number (digital channels only). A channel number sent by a local broadcaster. Usually the
virtual number is associated with the corresponding analog channel number. For example, a broadcaster may
associate digital channel 2-1 with their analog channel 2.
-- Physical Digital Channel Number. The channel number officially assigned to the actual broadcast frequency;
shown on screen in gray text.
Energy
Energy
Usage
Standard, Options for power consumption while the TV is powered off.
Fast Power • Standard keeps the TV’s energy use within ENERGY STAR® guideOn
lines while powered off.
• Fast Power On lets the TV power up quickly. The TV uses power
while in the off state in excess of ENERGY STAR guidelines for a
powered-down device.
Downloaded From TV-Manual.com Manuals
4. TV Menus
49
Initial, continued
Sound Projector
For full setup instructions, see page 34.
Basic Screen
Mode
(153, 249 series)
SoundPro
Auto
START
Perform Auto setup using the supplied calibration
microphone. See page 36.
Manual
Custom
To perform manual setup, see page 34.
Note: Do not perform manual adjustments after
running Auto setup. Doing so will erase all settings
created during Auto setup.
TV Location
Center, Left, L
Corner, Right, R
Corner
Highlight the item that best describes the TV’s location relative to the wall. Required for Manual setup.
TV Wall Length
(in feet)
[Enter digits]
Press
to change the number or enter digits. Required for Manual setup.
Other Wall
Length (in feet)
[Enter digits]
Press
to change the number or enter digits. Required for Manual setup.
TV to Sofa
(in feet)
[Enter digits]
Press
to change the number or enter digits. Enter the distance from the TV to the primary seating
area. Required for Manual setup.
Custom
(all models)
After defining the room layout, highlight Custom and press ENTER. Use this
option to fine-tune Sound Projector to your unique room layout. See details
on page 35.
Adjustments in the Custom Menu
Left Beam Angle
Right Beam Angle
Center Beam Angle
Left Surround Beam
Angle
Right Surround Beam
Angle
Left Level
Right Level
Center Level
Left Surround Level
Right Surround Level
•
•
•
Press
to select an
audio beam; colors of the
adjusters correspond to
audio beams in the onscreen diagram.
Press to redirect the
audio beam or change the
sound level.
To reset these adjustments, see “Resetting Angle and
Level Values in the Custom
Menu,” page 35.
Controls in the SoundPro > Custom menu adjust the direction and
focus of the TV’s sound output.
At extreme beam angles, adjustment may be limited and the
image on screen may not accurately represent the sound beams.
Downloaded From TV-Manual.com Manuals
50
4. TV Menus
Inputs
Name
Cablebox, Cam(corder), CD, DVD
(DVD, DVD2, Blu-ray), DVR, Game
(Game, PS, Xbox, Wii), MP3 Player,
PC, Satellite, VCR, AVR
Delete (deactivated HDMI only)
On/Off (Ant only)
•
•
•
•
•
Lets you assign or change names of inputs appearing in
the Activity menu.
-- Press to move between inputs.
-- Press
to select a name.
-- You cannot change the name of the current input; you
must first switch to another input. If you have only one
input, such as a cable box, make sure the Ant input is
On and switch to Antenna in the Activity menu before
renaming the single input.
Lets you turn the Ant input On/Off (to display/hide it in the Activity menu).
Lets you delete unused HDMI inputs from the Activity menu.
A CEC-enabled tuner can be named either Cable Box or
Satellite.
A CEC-enabled DVD player can be named DVD, DVD2, or
Blu-ray.
General Notes
When you change an input name in the Name menu and then exit the Name menu:
• The name is changed
• The icon in the Activity menu is changed
• Audio and video settings are changed to the defaults for the new device type.
• 153 and 249 Series: All previous NetCommand IR “learning” for the input is erased.
Notes for HDMI devices
• Disconnecting an HDMI device: When you disconnect an HDMI device, the icon remains in the Activity menu until
you remove it. Select Delete in the Inputs > Name menu to remove an unwanted icon for an HDMI input.
• If the New Device Found screen does not display as expected when you connect an HDMI device, see the
reset instructions under “Reactivating Auto Sensing for an HDMI Input,” page 13.
• HDMI Control and CEC-Enabled Devices: See Appendix B, “HDMI Control of CEC Devices,” page 75.
• If case of CEC conflicts: Turn off CEC signals in one of these ways:
-- Turn off the TV’s HDMI Control signals to the device (see below for HDMI Control).
-- Turn off each device’s internal CEC capability.
See Appendix B for the TV’s HDMI Control or, to turn on/off a specific device’s response to CEC signals, see
the device owner’s manual.
Learn
153 and 249 Series
Sets up or changes NetCommand IR control of the current viewing device.
See “About NetCommand IR Control,” page 55.
AVR
153 and 249 Series
Sets up or changes NetCommand IR control of an A/V receiver.
See “NetCommand IR Control of an A/V Receiver” on page 61.
HDMI Control
On, Off
Activity
•
•
•
Select On or Off to enable or disable the TV’s control of a CEC-enabled device. See Appendix B for use of this feature.
Lets you customize the Activity menu choices for the current input.
Highlight the activity name and press ENTER to make changes.
See “How is the Activity Menu Generated?” on the opposite page.
Downloaded From TV-Manual.com Manuals
4. TV Menus
Inputs, continued
How is the Activity Menu Generated?
The TV automatically generates the Activity menu. The
TV groups recognized device types based on how they
can be used. The device names used for the groupings are those you assigned in the New Device Found
menu or the Inputs > Name menu, or in some cases,
the name the device itself communicated to the TV. The table below summarizes the device groupings that
can appear in the Activity menu.
Key
Activity assignments made automatically by the TV.
X Activity assignments you can make using the
Inputs > Activity menu.
Watch
TV
Antenna
AV Receiver


Blu-ray
Cable Box

Camcorder
Watch
Movie
Play
Game
View
Photos


X

DVD2
DVR



Game
MP3 Player
PC

PS
Satellite


X

X
X



USB
VCR
VUDU
(249 Series)


Wii
X
Xbox
X
Downloaded From TV-Manual.com Manuals
X

CD/Audio
DVD
Listen
Music



X
X
X

X
X
X
51
52
4. TV Menus
Lock
TV Locks
Parental Menu
Parental
Lock by Program Ratings
Restricts access using U.S.-based ratings
sent by broadcasters.
Time
Lock by Time
Restricts TV use by time of day.
Panel
Other
Lock Control Panel
Disables the buttons on the TV’s control
panel. Use this option if small children
in the home try to press control-panel
buttons.
Lock by Other Program Ratings
Restricts access using non-U.S.-based
ratings sent by broadcasters.
Pass Codes
Setting a Pass Code
You are prompted to enter a pass code whenever you
select Lock on the main menu. To set a pass code for
the first time:
1. Press MENU and highlight Lock. A screen prompting you for a pass code will display.
2. Input a four-digit pass code using the number keys
on the remote control.
• Press CANCEL to delete a number and move
back one space.
• Press MENU or BACK to close the menu without
setting a pass code.
3. Press ENTER to set the pass code.
The TV comes from the factory with the rating locks
turned off and with pre-set U.S. ratings TV-PG and
movie rating PG. Turn on blocking for U.S. ratings
to activate these rating restrictions. Use the Lock >
Parental menu to change the level of blocking with U.S.
ratings.
Any time you change the channel or device, it may take
up to five seconds for the rating restrictions to take
effect.
Note: 249 Series. To set parental controls for
VUDU™ service, use the VUDU Info & Settings menu. The TV’s Parental menu does not
control content accessible through VUDU.
Other Menu (Alternate Rating System)
This TV can recognize new rating systems that may
come into effect in the future. The Other menu allows
you to block digital programming when such systems
come into effect.
The first time you tune to a channel broadcasting an
alternate rating system, the TV defaults to the most
restrictive setting if the Lock menu > Other Lock
option is set to On. Use this menu to change the
allowed rating if you are unable to watch a program
rated with an alternate system.
Bypassing TV Locks
•
Resetting a Pass Code
See the procedure in Appendix D.
•
•
•
•
Important Notes on Rating Locks
Parental menu rating locks apply only to channels and signals received on the ANT and composite VIDEO jacks.
Other menu rating locks apply only to digital channels received on ANT.
When viewing a cable box, satellite receiver,
or other device connected to the component
Y Pb Pr or HDMI inputs, check the device’s
owner’s guide for parental locks.
Downloaded From TV-Manual.com Manuals
If you try to watch a blocked program or the TV is
locked by time, a notice will appear prompting you
for a pass code. To use the TV, input your four-digit
pass code and press ENTER.
-- To reactivate the locks after using a pass code,
power the TV off and then on.
-- To reactivate only the parent ratings lock,
change to a different channel or device.
If a program is blocked, you can still use the TV
without entering a pass code. Change to a channel
airing an allowed program or change to another
device.
53
4. TV Menus
Lock, continued
Parental
Lock
Off, On
Start
Time
Sets the time of day for enforcement of rating restrictions set in the Parental menu.
1. Highlight the hour digits for Start Time.
2. Press
repeatedly to change the hour and associated AM/PM indicator. You can also just press
and hold to move quickly through the numbers.
3. Press ENTER to highlight the minutes.
4. With the minutes digits highlighted, press
repeatedly to change the minutes. You can also just
press and hold to move quickly through the numbers.
5. Highlight the Stop Time digits and set the time as described above.
Stop
Time
Disables or enables blocking based on V-Chip signals and the U.S. rating system.
Note: To make rating restrictions active 24 hours a day, make Start Time and Stop Time the same.
TV
Rating
TV-Y
Youth. For children under 7.
TV-Y7
Youth 7 and older.
TV-G
General Audience. For the entire family.
TV-PG
Parental Guidance. Parental Guidance recommended; may
not be suitable for some children.
TV-14
Adolescent 14 and older. Not recommended for children under 14.
TV-MA
Mature Audience. For adults only.
Highlight the rating level
you wish to change and
press ENTER to block it
( ) or allow it ( ).
You can apply supplemental content blocking
to the age-based ratings
by using the TV content
categories listed below.
FV
Fantasy Violence. Applies to TV-Y7 only.
D
Sexual Dialog. Applies in differing degrees to TV-PG and TV-14.
L
Adult Language. Applies in differing degrees to TV-PG, TV-14, and TV-MA.
S
Sexual Situations. Applies in differing degrees to TV-PG, TV-14, and TV-MA.
V
Violence (graphic or realistic). Applies in differing degrees to TV-PG,
TV-14, and TV-MA.
Movie
Rating
G
General Audience. Designed for the entire family.
PG
Parental Guidance. Parental Guidance recommended; may not be suitable for some children.
PG-13
Parental Guidance, 13 and Older. Not recommended for children under 13.
R
Restricted. Restricted in theaters to 17 years old and older unless accompanied by an adult.
NC-17
No Children 17 or Under. Restricted in theaters to 18 years old and older.
X
Adult. Designed for and restricted in theaters to adult audiences only.
Not Rated
No MPAA rating assigned
Downloaded From TV-Manual.com Manuals
TV Content
Categories
54
4. TV Menus
Lock, continued
Time
Blocks all use of the TV during the time period you specify. You must enter a pass code to use the
TV when the time lock is in effect.
Lock by Time
Enables/disables Lock by Time.
Lock Time,
Unlock Time
To set the lock and unlock times:
1. Highlight the hour digits for the Lock Time.
2. Press
repeatedly to change the hour and associated AM/PM indicator. To
move quickly through the numbers, just press and hold.
3. Press ENTER to set the hour and highlight the minutes.
4. With the minutes highlighted, press
repeatedly to change the minutes. To
move quickly through the numbers, just press and hold.
5. Highlight the Unlock Time digits and set the time as described above.
Note: To make Lock by Time active 24 hours a day, make Start Time and Stop Time
the same.
Off, On
Panel
Other
On locks and Off unlocks the buttons on the TV’s control panel. Use this option if
small children try to press TV buttons.
• To release the Panel Lock from the TV’s control panel, press and hold the
ACTIVITY button for ten seconds. If the TV is powered off, press POWER after the
lock releases to make the TV power on.
• To reactivate the lock, return to this menu and change the setting to On.
Other Menu Options (alternate rating system)
This TV can recognize new rating systems that may come into effect in the future. The Other option
remains grayed out until the TV receives a signal using an alternate rating system. Such alternate
rating systems will apply only to digital programming received on the ANT input.
Lock
On, Off
Enables/disables program blocking.
System Name The rating system available for the channel
Group
Rating groups available in the rating system shown on the screen. Rating groups are
defined by the rating system in effect.
Rating
Rating restrictions available in the selected rating system and group. Highlight the
rating and press ENTER to check (block) or uncheck (allow) rated content.
Downloaded From TV-Manual.com Manuals
5
NetCommand IR Control
About NetCommand IR Control
•
•
•
•
NetCommand IR home-theater control is available on 153 and 249 series TVs.
IR emitter cables are available for purchase
from Mitsubishi. Visit www.mitsuparts.com or call
800-553-7278 and request one of the following:
-- 242D483020 (two-ended cable)
-- 299P254020 (four-ended cable).
NetCommand setup is optional.
You can perform NetCommand setup when the TV
first recognizes a device during Auto Input Sensing
or at any convenient time afterward.
Downloaded From TV-Manual.com Manuals
•
•
NetCommand operates by sending remote control
signals from the TV to your other devices via the
IR (infrared) emitters, telling the devices to play,
record, change inputs, adjust volume, change channels, or perform other functions. All this is accomplished with the TV’s remote control left in TV mode.
You may wish to use NetCommand IR control to
supplement control of CEC-enabled devices.
Important Note on NetCommand
Be sure to connect the IR emitter cable to the
TV and properly place the emitters so that
NetCommand can control your devices.
55
sensor
IRIRsensor
56
On top of a single tall
device
5. NetCommand IR Control
IR Emitter Placement
The NetCommand system uses emitters connected
to the IR–NetCommand Output jack to control other
devices such as DVD players, cable boxes, satellite
ront of areceivers, and VCRs.
In front, shared by two
average-sized devices
IR sensor
IR sensor
Pr
gle averageIR emitter cables are available for purchase from
ed deviceMitsubishi. Call (800) 553-7278 and request either part
number 242D483020 (two-ended cable) or part number
299P254020 (four-ended cable).
or
Other A/V Device
1. Connect the plug end of the IR emitter cable to the
2.
3.
IR—NetCommand Output jack on the TV back panel.
When the New Device Found screen displays,
leave IR—NetCommand Output selected.
Highlight EXIT and press ENTER.
S
R
AVR AUDIO OUTPUT
L
TV
CH
D I G I T A L
SURROUND
A/V Receiver
Connecting IR–NetCommand Output
In front of a single
average-sized device
front, shared
two averagezed devices
The New Device Found screen displays when you
connect the IR emitter.
4. Position the emitter end with the emitter bulb facing
the device’s remote control sensor. The bulb emits
infrared light in a cone-shaped pattern. Place the
bulb far enough from the sensor to allow the cone
pattern to reach the sensor.
In some cases, the emitter works better facing
downward from the top of the device. Experiment
to find what works best.
5. Secure the emitter ends in place using double6.
sided tape.
Place any unused ends behind the devices to
prevent stray signals from reaching the IR sensors.
IMPORTANT
Position IR emitters so that each device’s
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
multiple sources (remote controls, IR emitters)
may not respond at all.
Downloaded From TV-Manual.com Manuals
sensor
IRIRsensor
On top of a single
tall device
In front, shared by
two average-sized
devices
IR sensor
IR sensor
IR sensor
Place IR emitters so the signal can be “seen” by the IR
sensor on each device.
If You are Unable to Locate
a Device’s IR Sensor
•
•
The IR sensor is usually behind the plastic window
of the front display panel. Using a flashlight, you
may be able to see it as a round or square cutout.
If you cannot see the sensor and the device’s
Owner’s Guide does not specify the location, do
the following using the device’s remote control.
1. Starting at one end of the plastic window, hold
the device’s remote control about one-half
inch from the front of the device and press the
POWER key.
2. If the device does not respond, move the
remote control one inch toward the center and
try again. Repeat until the device responds.
3. Repeat the previous steps starting at the other
end of the window. The sensor will be between
these two points.
5. NetCommand IR Control
57
Initial NetCommand Setup
To perform this procedure, you need:
• The remote controls for both the TV and the
device you want to control.
• An IR emitter cable available from Mitsubishi.
Note: To set up an A/V receiver, see “Setting Up A/V
Receiver Control,” page 62.
1. Connect and position the IR emitters for the
2.
3.
devices you wish to control. See “IR Emitter Placement” on the opposite page.
Set the TV’s remote control to TV mode and power
on the TV.
Open the NetCommand Learn screen as follows:
• If working from the New Device Found screen
after the device is first detected, highlight
NetCommand and press ENTER to open the
Learn screen for the device.
• If performing NetCommand setup at any time
after the device has been recognized through
Auto Input Sensing:
a. Press ACTIVITY.
b. Highlight the desired input icon and press
ENTER to switch to that input.
c. Press MENU, highlight Inputs, and highlight
Learn to open the Inputs > Learn screen
for the device.
From the New Device Found screen, highlight
NetCommand and press ENTER to open the Learn
screen.
Device-specific keys in the
rightmost column can be accessed
with the MORE key after “learning.”
4. The first function highlighted in the Learn screen
5.
6.
is always Power On. Aim the TV’s remote control
at the TV and press ENTER to begin learning for that
function.
When the Power On text starts flashing, aim the
device’s remote control at the TV and hold the POWER
key until a check mark appears next to Power On.
• If the text stops flashing before the check mark
appears, repeat the previous step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
Press the
keys on the TV’s remote control
to highlight other keys on the list. Repeat steps
4 and 5 for each additional function you wish to
control through NetCommand.
Note: Device keys in the far right column will be associated with the remote control’s MORE key when
“learned.” See the table on page 59.
7. If the device has a separate POWER OFF key, press
8.
on the TV’s remote to highlight Power Off. Repeat the earlier steps to “learn” the POWER OFF key.
If the device has no POWER OFF key, skip this step.
Press BACK to finish NetCommand “learning” for the
current device.
Downloaded From TV-Manual.com Manuals
Inputs > Learn screen
Key names marked with a
check have been “learned.”
Adding or Removing Device Keys from
NetCommand Control
1. Switch the TV to the device. Press ACTIVITY, high2.
3.
light the device’s icon, and press ENTER.
Open the Inputs menu and highlight the Learn icon.
When the Learn screen displays:
• To add keys: Continue as described earlier
under “Initial NetCommand Setup” on this
page.
• To delete keys: Highlight the name of the key
you wish to delete and press CANCEL on the
TV‘s remote control to clear the check mark.
58
5. NetCommand IR Control
Operating NetCommand-Controlled Devices
Controlling Most Device Types
As an example of NetCommand control, if you are
watching your cable box and you wish to tune to the
next channel higher, press CHANNEL Up. NetCommand
then sends the “learned” channel-up control signal to
the cable box.
1. Perform NetCommand setup for the device as
2.
3.
4.
described in this chapter.
When you wish to use the device, press ACTIVITY.
Press
to highlight the icon for the device.
Press ENTER to switch the TV to the device.
Note: if you have set up automatic input switching for
the A/V receiver, the A/V receiver will automatically switch to the correct input for the device.
5. To operate the device using the TV’s remote
control, press the side button to put the remote
control into TV mode.
6. Point the remote control at the TV (not the device)
and press the key for the desired function.
7. Press the MORE key to access additional key functions you may have “learned” for the device.
Special Operation Methods
Key Name in
Learning Screen
Special Operation Description and Setup
How to Use
Power On
Manual Power On/Off
Use for devices that have only one POWER key.
1. Press ACTIVITY.
2. Press
to highlight the icon for the
device to be powered on or off.
3. With the Activity menu still displayed, press
POWER to send the power signal; you may
need to press POWER twice.
Note: If you press POWER without the Activity
menu displayed, the TV will turn off.
4. Press ENTER to switch the TV to the device.
Power On
Power Off
Menu
Automatic Power On/Off
This feature is only for devices that have separate
Power On and Power Off keys on their original
remote controls. If your device does not have a
separate Power Off key, do not use the Power
Off learning position; use only the Manual Power
ON/OFF method described above.
In the NetCommand Learn screen:
a. “Learn” the Power On command in the
Power On learning position.
b. “Learn” the Power Off command in the
Power Off learning position.
•
To Power On the Device
1. Press ACTIVITY.
2. Press
to highlight the icon for
the device to be powered on or off.
3. Press ENTER to switch the TV to the
device and NetCommand will send the
Power On command to the device.
•
To Power Off the Device
When you turn the TV off, the TV sends all
learned Power Off commands to all devices.
Displaying a Menu for the Current Device
Press MORE and then 1 to send the menu
command to the current device.
“Learn” the MENU key on the original remote in the
Menu learning position.
Guide
Displaying the On-Screen Program Guide
(cable box or satellite receiver)
1. While watching the device, press GUIDE to
display the guide.
1. “Learn” the Guide key on the original remote in 2. Press PAGE UP/DOWN ( ) to send the Page
Up/Dn commands for the guide.
the Guide learning position.
2. Learn the PAGE UP and PAGE DOWN keys of the
original remote in the Page Up and Page
Down learning positions.
Downloaded From TV-Manual.com Manuals
59
5. NetCommand IR Control
Key Name in
Learning Screen
Special Operation Description and Setup
Enter
ENTER-Key Functions (cable boxes, satellite receivers, etc.)
Some devices have two keys that have “enter” functions. One key is for menus and is often labelled
SELECT or OK. A second key is for use with number keys for direct channel selection. NetCommand
uses the same ENTER key for both operations.
How to Use
When ENTER has a menu or guide function or
when the original remote control uses the same
key for menus and channel selection:
Learn the ENTER, SELECT, or OK key in the
NetCommand Enter learning position.
Enter (digits) When ENTER is for channel changes, i.e., the original remote control has a separate ENTER key for
this function):
1. Press MENU or GUIDE to display the device’s
menu or guide.
2. Press ENTER within the menu and
NetCommand will send the Enter signal for
menus.
Press digit key(s) and then press ENTER. NetCommand will send the Enter signal for
channel selection.
Learn the ENTER key for channel selection in
the NetCommand Enter (digits) learning position. Use this learning position only if the original
remote control has separate keys for Enter in
menus and Enter for channel selection.
Cancel
CANCEL as the Cancel or Exit Function
“Learn” the Cancel or Exit function in the
NetCommand Cancel learning position
1. Press MENU or GUIDE to display the menu or
guide.
2. Press CANCEL and NetCommand will send
the Cancel or Exit signal.
—
(separator)
The symbol “—” can serve as the separator
Press digit key(s) and press CANCEL. between a digital channel’s main and sub-channel NetCommand will send the channel-separator
digits, e.g., digital channel 12-1 (main channel is
signal.
12, sub-channel is 1).
“Learn” the channel separator function in the
NetCommand – (separator) learning position.
The MORE Key Menu and NetCommand
Menu
Top Menu
Input
Angle
SP/EP
Audio (DVD)
List
Subtitle
On Demand
Repeat
A
Bonus View
B
Setup
C
Surround
D
Night
Downloaded From TV-Manual.com Manuals
A/V
Receiver
DVD/
DVR
Cable/
SAT
Device
Key
VCR
A/V
Receiver
DVD/
DVR
Cable/
SAT
Device
Key
VCR
Perform NetCommand setup for these device-specific
keys and then access their functions with the MORE key.
60
5. NetCommand IR Control
Operating NetCommand-Controlled Devices, continued
NetCommand Specialized Device Keys
Refer to this chart when “learning” device keys. “Learn”
some, all, or none of the keys used for each device type.
See page 58 for more on keys marked in the “Special
Operation Method” column.
Function
Power On
Power On or Power ON/OFF (toggle)

Guide
On-Screen Program Guide or DVD Disc Menus

Channel +/Skip +
Next Channel Higher/
Skip Forward (Disc)
Channel –/Skip -
Next Channel Lower/
Skip Backward (Disc)
Page Up
Page Up in Guides
Page Dn
Page Down in Guides
Up
Arrow up
Down
Arrow down
Left
Arrow left
Right
Arrow right
Enter
Enter or Select (menus)
Cancel
Cancel or erase (menus)
Play
Start playback
Stop
Stop playback
Forward
Fast Forward
Rewind
Rewind/Fast Reverse
Pause
Pause playback
Record
Start Recording
1, 2, 3, 4, 5, 6, 7, 8, 9, 0
Digits
Enter (digits)
Use after entering digits to tune directly to a
channel by number

- (separator)
Add digital channel separator between main
channel number and sub-channel number

Last
Last Channel Recall
Info
On-screen status display or information display
Power Off
Power Off
Downloaded From TV-Manual.com Manuals
Name on TV
Remote Control
See Special
Operation
Method Table
Key Name in
Learning Screen


1, 2, 3, 4, 5, 6, 7, 8, 9, 0
May require two
keypresses

6
NetCommand IR Control
of an A/V Receiver
NetCommand IR home-theater control is available
on 153 and 249 series TVs.
Several types of A/V receiver control can be set up
using the Inputs > AVR menu.
• Power and volume. See the next page.
• Audio switching. For most equipment setups, see
“Case 1: Automatic A/V Receiver Switching to the
TV Audio Input” page 63.
• Audio switching and surround sound. To set up
switching to a surround sound device, see “Case
2: Automatic A/V Receiver Switching to a Surround
Sound Device” page 64
• Audio and video switching over HDMI. If your
A/V receiver has an HDMI output, it may be convenient to send audio and video to the TV over a
single HDMI cable through the A/V receiver. See
“Case 3: Automatic Audio and Video Switching via
HDMI,” page 65.
Note: To set up control of other device types, see
“Initial NetCommand Setup,” page 57.
Controlling an A/V Receiver
after NetCommand Setup
Switching Audio to and from the A/V
Receiver
1. Press MORE and then 9 (AUDIO).
2. Press to show the Speakers option.
3. Press to select either AV Receiver or TV.
Controlling A/V Receiver Power
With Any Connection Type
1.
2.
3.
4.
Press MORE and then 9 (AUDIO).
Press
to show the Speakers option.
Press to select AV Receiver.
Point the remote control at the TV (not the A/V
receiver) and press POWER to power the A/V
receiver on or off.
With an HDMI Connection
1. Press ACTIVITY.
2. Highlight the A/V receiver icon.
3. Press POWER.
Controlling Other A/V Receiver Functions
With the A/V receiver powered on and selected, the
TV’s remote control operates the volume and mute
functions. Also, when you switch to a device in the
Activity menu, the A/V receiver automatically switches
to the correct audio input for the device.
Downloaded From TV-Manual.com Manuals
61
62
6. NetCommand Control of an A/V Receiver
Setting Up A/V Receiver Control
Power and Volume
Perform this setup to control the A/V receiver power
and volume with the TV’s remote control.
To perform this setup you need:
• The remote controls for both the TV and the
A/V receiver.
• An IR emitter cable available from Mitsubishi.
Before You Begin
1. Connect your A/V receiver to the TV and any addi2.
3.
tional devices. See “Setting Up TV Inputs,” page 12
and “TV Connections,” page 16.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 56.
Set the TV’s remote control to TV mode using the
side button.
Inputs > AVR screen. Perform
NetCommand IR “learning” for A/V
receiver power and volume keys.
3. When the Power text starts flashing, aim the A/V
receiver’s remote control at the TV and hold the
POWER or POWER ON key until a check mark appears
next to Power.
• If the text stops flashing before the check mark
appears, repeat this step.
• To remove the key from NetCommand control,
press the CANCEL key while the key name is
highlighted.
Setup to Control A/V Receiver Power and Volume
1. Open the Inputs > AVR screen in one of two ways:
If using the New Device Found screen for the
A/V receiver, highlight NetCommand and press
ENTER to open the AVR screen.
• If performing NetCommand setup at any time
after Auto Sensing:
Press MENU, highlight Inputs, and highlight AVR
to open the AVR menu.
The first function highlighted in the AVR screen is
always Power. Aim the TV’s remote control at the
TV and press ENTER to begin learning for Power.
•
2.
IMPORTANT
To hear audio sent from the TV to the A/V receiver,
you must have:
• Physically connected the TV to the A/V
receiver.
• Assigned, if needed, the name AVR if using an
HDMI A/V receiver.
• “Learned” the IR codes for the A/V receiver
inputs.
• Assigned the TV’s audio output to the correct
input in the NetCommand Inputs > AVR menu.
• Selected the A/V receiver as the audio source.
Press MORE then 9 (AUDIO), then
to show
the Speakers option, then to select the A/V
Receiver.
Downloaded From TV-Manual.com Manuals
4. Press the
5.
6.
key on the TV’s remote control to highlight other keys in the list. Repeat steps 2 and 3 for
each additional function you wish to control through
NetCommand.
If the A/V receiver has a separate POWER OFF key,
press on the TV’s remote to highlight Power Off. Repeat steps 2 and 3 to “learn” the POWER OFF key. If the device has no POWER OFF key, skip this step.
When finished “learning” the power and volume
keys, either
• To watch TV, press bACK .
• To continue with NetCommand setup to control
switching of A/V receiver inputs, highlight
NEXT and press ENTER.
63
6. NetCommand Control of an A/V Receiver
Setting Up A/V Receiver Control, continued
Audio Available from TV only. Send audio from
the ANT input to the A/V receiver from the TV’s
analog or digital audio output.
Use this setup to make the A/V receiver switch to its
designated TV audio input when viewing programming
from the ANT input.
HDMI Digital Stereo Audio. Digital stereo audio
from an HDMI connection is available both in digital and analog format from the TV’s analog and digital
audio output jacks.
•
The following setups enable the A/V receiver to switch
automatically to the correct input when you select a
device in the TV’s Activity menu.
Three different connection arrangements are described
here. Review the descriptions to find the setup needed
for your equipment.
To hear digital surround sound from a source device
you must use the setup described for Case 2.
•
To set up control of an A/V receiver you need:
• The remote controls for the TV and A/V receiver.
• An IR emitter cable available from Mitsubishi.
• Connecting cables
Before You Begin
1. Connect your A/V devices to the TV and connect
2.
3.
4.
your A/V receiver to the audio outputs on the TV
and the DVD player. Note the name of the device
connected to each A/V receiver input. See initial
setup, page 12, and “TV Connections,” page 16.
Position NetCommand IR emitters as described in
“IR Emitter Placement,” page 56.
Set the TV’s remote control to TV mode using the
side button.
Open the Inputs > AVR menu, highlight NEXT
and press ENTER to display the device-key-learning
menu.
Case 1: Automatic A/V Receiver
Switching to the TV Audio Input
video
audio + video
IMPORTANT
All audio from what you are watching on the TV is
always available from both the TV’s AVR AUDIO
OUTPUT and DIGITAL AUDIO OUTPUT jacks.
To use the digital surround sound capabilities of
your A/V receiver however, you must connect the
audio output from your DVD player, satellite receiver,
or cable box directly to the A/V receiver.
VCR with
Analog Audio Output
analog audio
Automatic Switching (Audio or Audio/Video)
TV
audio output from
TV (digital or analog)
TV audio
out
TV audio input
A/V Receiver
Incoming Coaxial Cable
to TV’s ANT input
Important: To use this setup, you must connect the TV’s
audio output to the A/V receiver’s TV audio input jack.
1. In the Inputs > AVR menu, press
2.
3.
4.
5.
to highlight
TV audio out as the A/V receiver input to control.
Press ENTER on the TV’s remote control.
While the text TV audio out is flashing, press and
hold the TV INPUT key on the A/V receiver’s remote
control.
When a check appears next to TV audio out,
release the TV INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press
CANCEL while the name is highlighted.
Press MENU if finished or continue with Case 2 setup
if you want to control surround sound switching for
another audio source.
Most devices are set up to use the TV’s audio output like
the VCR in this example; analog audio from the device is
sent through the TV to the A/V receiver’s TV audio input.
Use this setup for:
• Analog Stereo Audio. Audio from sources with only
analog stereo output (such as a VCR) can be sent either
directly to the A/V receiver or through the TV first.
Mitsubishi recommends you send audio through the
TV as shown in the example. The TV converts analog
audio to digital format to send to a digital A/V receiver.
Downloaded From TV-Manual.com Manuals
Case 1: NetCommand setup for controlling A/V
receiver switching to the A/V receiver’s audio input
from the TV. The list displayed represents inputs in use.
The device names are those you assigned in the New
Device Found screen or in the Inputs > Name menu.
analog audio
64
6. NetCommand Control of an A/V Receiver
Setting Up A/V Receiver Control, continued
Case 2: Automatic A/V Receiver Switching
to a Surround Sound Device
Note: Use this setup to send digital surround sound
from a source device directly to your external sound
system. For non-surround sound source devices,
Mitsubishi recommends using the setup for Case 1,
in which audio is sent through the TV.
A device can send
digital
sound such as Dolby
DVD
Playersurround
with
digital surround sound
Surround
Digital or DTS Digital
directly
to theSound
A/V receiver. The device might
be a DVD player, cable box, or satellite receiver, and could
have HDMI output. A DVD player is used in this example.
Case 2: NetCommand setup for
Your setup may include additional devices with digital
controlling A/V receiver switching
surround sound connected directly to the A/V receiver. to the A/V receiver’s DVD input. The list contains
These devices might be a DVD player plus a cable box
connected inputs with names assigned during Auto
or satellite receiver.
Input Sensing.
DVD Player digital surround sound
with
Digital
Surround
video
Sound
TV
DVD audio
input
A/V Receiver
3. While the text DVD is flashing, press and hold the
4.
Case 2: A/V receiver audio from a device providing
surround sound directly to the A/V receiver
1. In the Inputs > AVR menu, press
2.
to highlight
the name of the A/V receiver input to control. In this
example, it is the DVD input.
Press ENTER on the TV’s remote control.
Downloaded From TV-Manual.com Manuals
5.
DVD INPUT key on the A/V receiver’s remote control.
When a check appears next to DVD, release the
DVD INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press
CANCEL while the name is highlighted.
If finished, highlight EXIT and press ENTER or
continue to set up additional A/V receiver audio
sources.
65
6. NetCommand Control of an A/V Receiver
Setting Up A/V Receiver Control, continued
Case 3: Automatic Audio and
Video Switching via HDMI
If your A/V receiver has an HDMI output, it may be
convenient to route video signals from multiple devices
over a single cable to the TV. Use this procedure to set
up NetCommand control of the A/V receiver’s audio
and video switching over a single HDMI cable. The
connected source devices can be analog, digital, or a
mixture or the two. When this setup is complete, you
can use the TV’s Activity menu to select a video device
connected to the A/V receiver.
TV
A/V Receiver
1. Connect the A/V receiver to the TV with an HDMI2.
HDMI
Output
3.
HDMI Cable
VCR
Blu-ray player
Cable box
DVD player
More About Using an HDMI Connection
• Audio from devices connected directly to the TV
can be heard from the TV speakers only. To send
audio to the A/V receiver from such devices, use
one of the optional audio connections shown in the
diagram on this page. For example, use an optional
audio connection if you wish to use the A/V receiver
speakers to hear audio from:
-- The ANT input
L
R
-- A game or camcorder connected to the conveAUDIO
nience input (input 3).
• To use NetCommand to supplement HDMI control
of a CEC-enabled A/V receiver, the recommended
setup sequence is:
1. Connect the HDMI cable.
2. Enable HDMI control (New Device Found screen).
3. Connect the secondary digital audio cable, if
desired.
4. Perform NetCommand setup.
If you connect to HDMI after performing
NetCommand setup for the A/V receiver, the
NetCommand setup will be lost.
•
Before You Begin
To complete these steps you will need:
• The remote controls for both the TV and the
A/V receiver.
digital surround
sound
• An IR
emitter cable available from Mitsubishi.
• An HDMI-to-HDMI cable to connect the A/V
receiver to the TV and cables necessary to
connect devices to the A/V receiver.
In some circumstances, audio from a device connected to the A/V receiver may not be passed over
the HDMI cable to the TV speakers. In these cases
you must use the A/V receiver speakers to hear audio.
Downloaded From TV-Manual.com Manuals
to-HDMI cable. Do not connect the optional audio
cable at this time.
If desired, enable HDMI Control of a CEC-enabled
A/V receiver. See Appendix B, “HDMI Control of
CEC Devices.”
Connect your audio/video devices to the A/V
receiver. Note the name of the device connected
to each A/V receiver input. This information will be
needed later to set up NetCommand’s automatic
input switching.
R
AVR AUDIO OUTPUT
L
TV
Optional
analog or
digital audio
connection
HDMI cable
A/V receiver with
HDMI output
HDMI OUT
L
R
ANALOG AUDIO IN
Any connection
types
High-definition
DVD player
DIGITAL
AUDIO IN
VCR
DVD player
Cable box
Multiple video inputs through a single HDMI cable. You can
connect multiple video devices to an A/V receiver that has
an HDMI output. The optional audio connection allows you
to hear, through the A/V receiver, devices connected to the
TV only, e.g., an antenna on the ANT input.
66
6. NetCommand Control of an A/V Receiver
Setting Up A/V Receiver Control, continued
4. If using an optional audio cable between the TV and
5.
A/V receiver, connect it.
Connect the IR emitter cable to the TV and position
the IR emitter where it can send signals to the A/V
receiver. See “IR Emitter Placement,” page 56.
Setup to Control Automatic Audio
and Video Switching via HDMI
When this setup is complete, the “learned” A/V receiver
input will appear in the TV’s Activity menu as a selectable input.
NetCommand Control of a Device Connected to an HDMI A/V Receiver
Use this setup to have NetCommand control a device
sending audio and video through the A/V receiver to the
TV via HDMI.
You must have already completed the procedure under
“Setup to Control Automatic Audio and Video Switching
via HDMI” on this page. That procedure places an icon
in the Activity menu for the device (input) connected to
the A/V receiver.
Any Connection
Type
1. Power on the A/V receiver.
2. Set the TV’s remote control to TV mode using the
3.
4.
5.
side button.
Power on the TV.
When the New Device Found screen displays,
select device name AVR if it is not recognized automatically.
Navigate to the Inputs > AVR menu or, from
within the New Device Found screen, highlight
NetCommand and press ENTER.
Source
Device
2.
5.
6.
7.
6. In the Inputs > AVR menu, press
to highlight
the name of the A/V receiver input to control. In this
example, it is the DVD input.
7. Press ENTER on the TV’s remote control.
8. While the text DVD is flashing, press and hold the
DVD INPUT key on the A/V receiver’s remote control.
9. When a check appears next to DVD, release the
DVD INPUT key.
• If the text stops flashing before the check mark
appears, repeat this step.
• To erase the IR code just “learned,” press
CANCEL while the name is highlighted.
10.If there are no more devices to set up, highlight
EXIT and press ENTER or continue to set up additional A/V receiver audio/video sources.
Downloaded From TV-Manual.com Manuals
TV
1. Set up NetCommand control of A/V receiver audio/
3.
4.
To set up A/V switching over HDMI, choose your
devices from a list. Unlike the device list described for
Case 2, this is a generic list containing more than just
the devices detected in your setup.
A/V
Receiver
HDMI
Cable
video switching via HDMI as described on this
page.
Press BACK to close any open menus and return to
normal TV viewing.
Press aCTIVITY.
Highlight the icon for the A/V receiver input you
wish to control.
Press ENTER to switch the TV to the A/V receiver
and the A/V receiver to the input.
Open the Inputs > Learn menu.
Perform NetCommand “learning” for the connected device by following the steps in “Initial
NetCommand Setup,” page 57.
Appendices
67
Appendix A: Programming the Remote Control. . . . . . . . . . . .
68
Appendix B: HDMI Control of CEC Devices.. . . . . . . . . . . . . .
75
Appendix C: TV Care. . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
Appendix D: Bypassing the Parental Lock. . . . . . . . . . . . . . .
79
Appendix E: Troubleshooting. . . . . . . . . . . . . . . . . . . . . . .
81
Downloaded From TV-Manual.com Manuals
68
Appendices
Appendix A: Programming the Remote Control
This appendix explains programming the TV’s remote
control to operate other A/V devices. This is distinct
from NetCommand control.
Functions Available for Other A/V Devices
The TV’s remote control can be programmed to operate
other types and brands of A/V products. The functions
performed in each switch position vary depending on
the product. Not all functions work for all models. The
most common functions available are listed on this
page.
VCRs and DVRs
•
•
•
•
•
•
CHANNEL UP/DN
POWER
SLEEP (from MORE menu)
(FAST Forward)
(Pause)
(Play)
•
•
•
•
•
•
(Record)
(Reverse)
(Stop)
GUIDE (DVR only)
MENU (DVR only)
0–9 Number Buttons
Mitsubishi VCRs are compatible with some additional keys.
Cable Boxes and Satellite Receivers
(not all functions for all models)
Control modes
ACTIVITY
GUIDE
MENU
INFO
BACK
•
•
•
•
•
•
•
•
•
To use the remote after
programming, press the side
button to change the control
mode to match the device
type.
The MORE Menus
Press the MORE key to display a menu showing additional key functions available after programming the
remote control for a device.
249 Series Supplemental Keys
The supplemental cable box keys offered with the 249
series may provide additional controls. Program the
remote control for your cable box and test the keys.
The TV’s remote control may
operate the Favorites and On
Demand features of your cable box.
The F1–F4 keys work like the A, B, C,
D buttons on some cable boxes.
IMPORTANT
Some manufacturers may change their products
or they may use more than one remote control
system. The TV’s remote control may be unable
to operate your A/V equipment in these cases.
Downloaded From TV-Manual.com Manuals
PAGE UP/DOWN
Cancel
CHANNEL UP/DN
ENTER
GUIDE
POWER
LAST (ENTER; for channels on some models)
0–9 Number Keys
The record/playback keys:
•
(FAST Forward)
•
(Pause)
•
(Play)
•
(Record)
•
(Reverse)
•
(Stop)
249 Series Keys for
Cable Boxes
• FAV
• ON DEMAND
• F1–F4
A/V Receivers
•
•
•
•
•
MUTE
•
POWER
SLEEP (from MORE menu)
VOLUME
0–9 Number Buttons
Direct Input Selection
buttons: numbers
and LAST (on some
Mitsubishi models)
CD Players
(not all functions for all models)
•
•
•
•
SLEEP (from MORE menu) •
(FAST Forward)
•
(Pause)
•
(Play)
(Reverse)
(Stop)
0–9 Number Buttons
DVD Players
(not all functions for all models)
•
•
•
•
•
•
•
CANCEL (on some
models)
CHANNEL UP/DN (for
track skip on some
models)
ENTER
MENU
POWER
SLEEP (from MORE menu)
•
•
•
•
•
•
•
(FAST Forward)
(Pause)
(Play)
(Record)
(Reverse)
(Stop)
0-9 Number Keys
69
Appendices
Appendix A: Programming the Remote Control, continued
Programming the Remote Control
1. Press the side button on the remote control to
change to the correct mode for the product you
want to control. Refer to the table below. Only
one of each device type can be controlled in each
mode.
Mode
Affected Device
Cable/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
VCR
Audio
A/V Receiver
Audio Amplifier
CD Player
2. Press and hold POWER on the remote control for
3.
4.
5.
6.
several seconds until the mode indicator blinks
twice and goes off.
Release the POWER key.
Enter the first five-digit code listed for your equipment.
• The mode indicator blinks twice when you
start to enter the code and then once for each
additional keypress.
• The mode indicator blinks twice when you finish
entering a valid code.
• If you need to start over or wish to exit programming mode, temporarily change to a
different mode using the side button.
Point the remote control at the equipment and
press POWER. If the product has no power on/off
function, press a different key, such as
(Play),
(Stop), VOLUME UP, or MUTE.
• If the equipment responds, the remote control
is properly programmed.
• If the equipment does not respond, repeat
steps 2–4 with the next five-digit code listed for
your equipment.
Once you have found the correct code, write it in
the space below for future reference.
Mode
Code
CABLE/SAT
VCR
DVD
AUDIO
IMPORTANT
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
To determine the code programmed for any mode:
1. Set the mode to the one you wish to verify.
2. Press and hold POWER on the remote control for
several seconds until the mode indicator blinks twice
and goes off.
3. Press keys 9 9 0
4. Press 1 and count the blinks of the power key. Write down the number of blinks as the first digit of
the code.
5. Repeat step 4 for the second, third, fourth, and fifth
digits of the code.
Audio Lock: Universal A/V
Receiver Control
With Audio Lock enabled, the remote control operates
volume and mute on the A/V receiver in all modes set by
the side button. Activate Audio Lock if you normally use
an A/V receiver with your TV and other A/V equipment.
1. Program AUDIO mode for your A/V receiver as
2.
3.
described in “Programming the Remote Control” on
this page.
With the remote control in AUDIO mode, hold POWER
on the remote control for several seconds until the
mode indicator blinks twice and goes off.
Press keys 9 9 3 ENTER
The mode indicator will blink twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
1. Press and hold POWER for several seconds until the
2.
Downloaded From TV-Manual.com Manuals
Device Type
mode indicator blinks twice and goes off.
Press keys 9 9 3 VOLUME UP.
The mode indicator will blink four times to indicate
Audio Lock has cleared.
70
Appendices
Appendix A: Programming the Remote Control, continued
Programming Codes
Audio Amplifiers
Adcom
41100, 40577
Altec Lansing 41742
Bel Canto
41583
Design
Bose
40674
Carver
40892
Cary Audio
41879
Design
Classe
41461
Flextronics
41879
Halcro
41934
Harman/
40892
Kardon
JVC
40331
Krell
41837
Left Coast
40892
Lexicon
41802, 41145
Marantz
40892
Mark
41483
Levinson
Parasound
41934
Philips
40892
Polk Audio
40892
Victor
40331
Yamaha
40354
Cable Boxes
A-Mark
10144, 10008
ABC
10237, 10008
Acorn
10237
Action
10237
Active
10237
Americast 10899
Amino
11822, 11602
Archer
10237
Bell South 10899
Century
10008
Cisco
11982, 11877, 10877
Comcast
11982
Digeo
12187
Director
10476
GE
10144
General 10476
Instrument
GoldStar
10144
Hitachi
10008
i3 Micro
11602
Insight
10476
Jerrold
10476
Memorex
10000
Motorola
11376, 11254, 10476
Myrio
11822, 11602
Nova Vision 10008
Novaplex
10008
Pace
11877, 10877, 10237,
10008
Panasonic 11982, 10144, 10008,
10000
Downloaded From TV-Manual.com Manuals
Cable Boxes
Paragon
10525, 10008, 10000
Penney
10000
Philips
11305
Pioneer
11877, 10877, 10533,
10144
Pulsar
10000
Quasar
10000
Runco
10000
Samsung
10144
Scientific
11877, 10877, 10477,
Atlanta
10237, 10008, 10000
Sejin
11602
Sony
11006
Sprucer
10144
Toshiba
10000
US Elec10008
tronics
Videoway
10000
Zenith
10899, 10525, 10000
CD Players
Acoustic
Research
Akai
Burmester
California
Audio Labs
DKK
Fisher
Garrard
Hafler
Harman/
Kardon
Inkel
Integra
JVC
Kenwood
KLH
Koss
LG
Magnavox
Marantz
McIntosh
MCS
Memorex
MGA
Miro
Mitsubishi
Modulaire
MTC
NAD
Onkyo
Optimus
Panasonic
40420
40083
40420
40029
40000
40000
40420
40173
41202, 40173, 40100,
40083
40180
40101
41294, 40072
40626, 40190, 40037,
40029, 40000
41711, 41318
41317
41208
40038
40626, 40435, 40180,
40038, 40029
41703
40029
40420, 40000
40083
40000
40098, 40083
40420, 40180, 40087,
40000
40420
41208
41327, 40101
40420, 40087, 40037,
40000
40752, 40388, 40029
CD Players
Parasound
Penney
Philips
Pioneer
Proceed
Quasar
RadioShack
RCA
Realistic
Roksan
Rotel
Sansui
Sanyo
Sharp
Sherwood
Sony
Symphonic
Tascam
TDK
Teac
Technics
Victor
Wards
Yamaha
Yorx
40420
40029
40626
41087
40420
40029
40420, 40180, 40000
40420
40420, 40180, 40087,
40000
40435
40420
40000
40087, 40000
40180, 40037
41950, 40180
41364, 40490, 40185,
40100, 40000
40180
40420
41208
40490, 40420, 40180
40029
40072
40087
41292, 40490, 40036
40000
A/V Receivers
ADC
40531
Aiwa
41641, 41405, 41388,
41243, 40189, 40121
Alco
41390
AMC
41077
Anam
41609, 41074
Arcam
41189
Audiotronic 41189
Audiovox
41390
Bose
41933, 41841, 41629,
41253, 41229, 40639
Cairn
40189
Capetronic 40531
Carver
41289, 41189, 40189,
40121
Curtis
40014
Mathes
Daewoo
41250
Denon
41360, 41306, 41142,
40121
Emerson
40531
Fisher
41801
Grundig
40189
Harman/
41306, 41304, 41289,
Kardon
40891, 40189, 40110
Hitachi
41801
Insignia
42169, 41893, 41077,
41030
71
Appendices
Appendix A: Programming the Remote Control, continued
Programming Codes, continued
A/V Receivers
Integra
41805, 41320, 41298,
40842
JBL
41306, 40110
JVC
42331, 41643, 41495,
41374, 41282, 41058
Kawasaki
41390
Kenwood
41570, 41569, 41313
KLH
41428, 41390
LG
42197, 41293
Linn
40189
Magnavox
41514, 41269, 41266,
41189, 40531, 40189
Marantz
41289, 41269, 41189,
40891, 40189
McIntosh
41289
Micromega 41189, 40189
Mitsubishi
41957, 41922, 41921,
41920, 41393
Myryad
41189
Nakamichi
41313
Onkyo
41905, 41805, 41320,
41298, 40842
Optimus
41074, 41023, 40531,
40121, 40014
Panasonic
42967, 41764, 41763,
41633, 41548, 41518,
41509, 41316, 41308,
41288, 41275
Philips
41269, 41266, 41189,
40891, 40531, 40189
Pioneer
41935, 41384, 41123,
41023, 40630, 40531,
40150, 40014
Polaroid
41508
Polk Audio 41289, 40189
Proscan
41254
RadioShack 41609
RCA
41609, 41511, 41390,
41254, 41123, 41074,
41023, 40531
Realistic
41609, 40121
Revox
40189
Rio
41869
Samsung
41500, 41304, 41295
Sansui
41189, 40189
Sanyo
41801
Sherwood
42169, 41905, 41077
Sherwood
42169
Newcastle
Sonic Blue 41869
Sony
41858, 41822, 41759,
41758, 41658, 41622,
41558, 41441, 41382,
41258, 41131, 41058
Stereophonics 41023
Sunfire
41313
Teac
41390, 41074
Downloaded From TV-Manual.com Manuals
A/V Receivers
Technics
41518, 41308
Thorens
41189
Toshiba
41788, 41123, 40842
Venturer
41390
Wards
40189, 40014
Yamaha
41815, 41476, 41376,
41375, 41331, 41276,
41176, 41023, 40176
YBA
41921
Zenith
41293
Satellite Receivers
Bell ExpressVu 11170, 10775
Chaparral
10216
Crossdigital 11109
DirecTV
11856, 11749, 11640,
11639, 11609, 11442,
11414, 11392, 11377,
11142, 11109, 10819,
10749, 10639, 10566,
10392, 10247, 10099
Dish
11775, 11505, 11170,
Network
10775
System
Dishpro
11775, 11505, 10775
Echostar
11775, 11505, 11170,
10775
Expressvu 11775, 10775
Fortec Star 11821
Funai
11377
GE
10566
GOI
11775, 10775
Hitachi
11250, 10819, 10749
Houston
10775
HTS
11775, 10775
Hughes
11749, 11442, 11142,
Network
10749
Systems
Humax
11790, 11781
Innova
10099
JVC
11775, 11170, 10775
LG
11414
Magnavox 10722
Mitsubishi 10749
Netsat
10099
Panasonic 10701, 10247
Pansat
11807
Philips
11749, 11442, 11142,
10775, 10749, 10722,
10099
Proscan
10566, 10392
RadioShack 10775, 10566
RCA
11442, 11392, 11142,
10855, 10775, 10566,
10392, 10143
Samsung
11609, 11442, 11377,
11276, 11142, 11109
Satellite Receivers
SKY
10099
Sony
11640, 11639, 10639
Thomson
10566, 10392
Tivo
11442, 11142
Toshiba
11749, 10790, 10749
UltimateTV 11640, 11392
Uniden
10722
Zenith
11856, 11810
VCRs
A-Mark
ABS
Accurian
Admiral
Adventura
Aiko
Aiwa
Akai
Alba
Alienware
Allegro
America
Action
American
High
Amstrad
Astra
Audiovox
Avis
Bell &
Howell
Bell
ExpressVu
Broksonic
20278, 20046, 20037,
20000
21972
20000
20479, 20209, 20060,
20048, 20047, 20039
20037, 20000
20278
20124, 20037, 20000
20242, 20175
20278, 20209
21972
20039
20278
20081, 20035
20000
20035
20278, 20038, 20037
20000
20479, 20048, 20046,
20039, 20035, 20000
21944
20479, 20209, 20184,
20121
Calix
20037
Candle
20038, 20037
Canon
20035
Carver
20081, 20035
CCE
20278
Cineral
20278
Citizen
20479, 20278, 20209,
20037, 20035, 20000
Classic
20037
Colortyme 20278, 20060, 20045,
20035
Colt
20000
Craig
20047, 20037
Criterion
20000
Crosley
20081, 20035, 20000
Crown
20278
Curtis
20432, 20278, 20162,
Mathes
20060, 20035, 20000
CyberPower 21972
Daewoo
20278, 20046, 20045,
20037
72
Appendices
Appendix A: Programming the Remote Control, continued
Programming Codes, continued
VCRs
Daytron
Dell
Denon
DirecTV
Dish
Network
System
Dishpro
Dual
Durabrand
Dynatech
Echostar
Electrohome
20278, 20037
21972
20081, 20042
20739
21944
21944
20000
20039, 20038
20000
21944
20209, 20060, 20043,
20037, 20000
Electrophonic 20037
Emerald
20184, 20121
Emerex
20032
Emerson
21593, 20593, 20479,
20278, 20209, 20184,
20121, 20043, 20037,
20000
Expressvu 21944
Fisher
20047, 20046, 20039,
20000
Fuji
20035, 20033
Fujitsu
20000
Funai
21593, 20593, 20278,
20037, 20000
Garrard
20000
Gateway
21972
GE
20060, 20048, 20035,
20000
Gemini
20060
Genexxa
20278, 20037, 20000
GFM
21593
Go Video
20614, 20432
GOI
21944
GoldStar
20278, 20039, 20038,
20037, 20035, 20000
Goodmans 20278, 20081, 20037,
20000
Gradiente
20000
Granada
20081, 20042
Grundig
20081
Harley
20000
Davidson
Harman/
20081, 20075, 20038
Kardon
Headquarter 20046
Hewlett
21972
Packard
HI-Q
20047, 20035, 20000
Hitachi
20089, 20045, 20042,
20037, 20035, 20000
Howard
21972
Computers
HP
21972
Downloaded From TV-Manual.com Manuals
VCRs
HTS
Hughes
Network
Systems
Humax
Hush
Hytek
iBUYPOWER
Instant
Replay
Jensen
JVC
KEC
Kenwood
Kodak
KTV
LG
Linksys
Lloyd’s
Loewe
Logik
Lumatron
Luxor
LXI
21944
20739, 20042
21988, 21797, 20739
21972
20047, 20000
21972
20035
20067
21944, 20067
20278, 20037
20067, 20046, 20038
20037, 20035
20000
20038, 20037
21972
20038, 20000
20081
20000
20278
20046
20067, 20042, 20037,
20000
Magnasonic 20593, 20278, 20037,
20000
Magnavox 21593, 20618, 20593,
20563, 20081, 20048,
20039, 20037, 20035,
20000
Marantz
20081, 20038, 20035
Marta
20037
Matsui
20209, 20037
Matsushita 20162, 20081, 20035
Media
21972
Center PC
MEI
20035
Memorex
20479, 20278, 20209,
20162, 20048, 20047,
20046, 20039, 20037,
20035, 20000
Metz
20037
MGA
20060, 20043
Microsoft
21972
Mind
21972
Minolta
20042
Mitsubishi 20443, 20242, 20214,
20173, 20075, 20067,
20060, 20048, 20047,
20043, 20042, 20000
Motorola
20048, 20035
MTC
20000
MTX
20000
Multitech
20039, 20000
NEC
20067, 20038
Nikko
20278, 20037
VCRs
Nikkodo
Niveus
Media
Northgate
Olympus
Onkyo
Optimus
20278, 20037
21972
21972
20162, 20035
20222
21062, 21048, 20593,
20432, 20162, 20048,
20047, 20037, 20035,
20000
Orion
20479, 20278, 20209,
20184, 20121, 20000
Panama
20035
Panasonic 21062, 20616, 20614,
20225, 20162, 20035,
20000
Penney
20162, 20081, 20067,
20047, 20042, 20038,
20037, 20035, 20000
Pentax
20042
Philco
20479, 20209, 20081,
20035, 20000
Philips
21181, 21081, 20739,
20618, 20616, 20209,
20162, 20081, 20048,
20045, 20035, 20000
Pilot
20037
Pioneer
20162, 20081, 20067,
20042
Polk Audio 20081
Portland
20278
Presidian
21593
Proscan
20060
Protec
20000
Pulsar
20278, 20039
Quarter
20046
Quartz
20047, 20046, 20035
Quasar
20162, 20035
RadioShack 20162, 20048, 20047,
20046, 20037, 20035,
20000
Radix
20037
Randex
20037
RCA
20880, 20060, 20048,
20045, 20042, 20035,
20000
Realistic
20278, 20162, 20121,
20048, 20047, 20046,
20037, 20035, 20000
ReplayTV
20616, 20614
Ricavision 21972
Runco
20039
Salora
20075
Samsung
20739, 20432, 20060,
20045, 20038, 20000
Sanky
20048, 20039
Appendices
73
Appendix A: Programming the Remote Control, continued
Programming Codes, continued
VCRs
Sansui
20479, 20209, 20067,
20000
Sanyo
20479, 20159, 20047,
20046, 20000
Scott
20184, 20121, 20045,
20043
Sears
20209, 20162, 20067,
20060, 20048, 20047,
20046, 20045, 20043,
20042, 20039, 20037,
20035, 20033, 20000
Sharp
20848, 20048, 20047,
20032, 20000
Shintom
20039, 20000
Siemens
20037
Signature
20479, 20060, 20048,
20046, 20037, 20035,
20000
Singer
20037
Sonic Blue 20616, 20614
Sonographe 20046
Sony
21972, 21032, 20636,
20067, 20047, 20046,
20035, 20033, 20032,
20000
Soundmaster 20000
Stack 9
21972
STS
20042
SV2000
20000
SVA
20000
Sylvania
21593, 20593, 20081,
20043, 20035, 20000
Symphonic 21593, 20593, 20000
Systemax
21972
Tagar
21972
Systems
Tandy
20000
Tashiko
20037
Tatung
20081, 20067, 20048,
20000
Teac
20067, 20000
Technics
20162, 20037, 20035,
20000
Teknika
20037, 20035, 20000
Tevion
20479
Thomas
20000
Thomson
20060
Tisonic
20278
Tivo
21944, 20739, 20636,
20618
TMK
20000
TNIX
20037
Toshiba
21988, 21972, 21008,
20209, 20045, 20043,
20000
Tosonic
20278
Totevision 20037
Downloaded From TV-Manual.com Manuals
VCRs
Touch
Trix
Ultra
Vector
Vector
Research
Victor
Video Concepts
Videomagic
Videosonic
Viewsonic
Villain
Voodoo
Wards
21972
20037
20278, 20045
20045
20184, 20038
20067
20242, 20045
20037
20000
21972
20000
21972
20479, 20081, 20060,
20048, 20047, 20046,
20045, 20043, 20042,
20038, 20037, 20035,
20033, 20000
Wharfedale 20593
White
20479, 20278, 20209,
Westinghouse 20000
World
20479, 20209
XR-1000
20035, 20000
Yamaha
20038
Zenith
21139, 20479, 20278,
20209, 20039, 20037,
20033, 20000
ZT Group
21972
DVD and Blu-ray Players
3D LAB
30539, 30503
Accurian
31416, 30675
Acoustic
30730
Solutions
Adcom
31094
Afreey
30698
Aiwa
30641, 30533
Akai
31089, 30770, 30705,
30695
Alba
30717, 30672
Alco
30790
Allegro
30869
Amphion
30872
Media
Works
AMW
30872
Apex Digital 31061, 31056, 31020,
31004, 30797, 30796,
30794, 30755, 30717,
30672, 30533
Arrgo
31023
Aspire
31168, 31407
Digital
Astar
31489
Audiovox
31041, 30790, 30717
Awa
30730
DVD and Blu-ray Players
B&K
30662, 30655
BBK
31224
Bel Canto
31571
Design
Blaupunkt 30717
Blue Parade 30571
Blue Sky
30699, 30695
Bose
32023, 31895
Brandt
30651
Broksonic 30695
California
30490
Audio Labs
Celestial
31020
Centrex
31004, 30672
Cinea
30831
CineVision 30869, 30833
Citizen
32116, 31587, 31277,
31003, 30695
Clairtone
30571
Coby
31351, 31177, 31165,
31107, 31086, 31077,
30852, 30778
Craig
30831
Creative
30539, 30503
Curtis
31087
Mathes
CyberHome 31537, 31502, 31129,
31117, 31024, 31023,
30874, 30816
Cytron
30705
Daewoo
31242, 31234, 31172,
31169, 30869, 30833,
30784, 30770, 30705
Dansai
30770
Daytek
30872
Decca
30770
Denon
32258, 30634, 30490
Denver
30778
Desay
31407
DigitalMax 31738
Digitrex
30672
Disney
31270, 30675
DiViDo
30705
Dual
31068, 30675
Durabrand 31127, 31023
DVD2000
30521
Electrohome 32116, 31003
Emerson
31268, 30675, 30591
Enterprise 30591
Entivo
30539, 30503
Enzer
30770
ESA
31268
Firstline
30651
Fisher
30670
Funai
31268, 30675
Gateway
31158, 31077, 31073
GE
30815, 30717, 30522
74
Appendices
Appendix A: Programming the Remote Control, continued
Programming Codes, continued
DVD and Blu-ray Players
GFM
31268, 30675
Go Video
31730, 31304, 31158,
31144, 31099, 31075,
31044, 30869, 30833,
30783, 30744, 30741,
30717, 30715, 30573
GoldStar
30869, 30741
Goodmans 30790
GPX
30769, 30699
Gradiente
30651, 30490
Greenhill
30717
Grundig
30705, 30539
Harman/
30702, 30582
Kardon
Hello Kitty 30831
Hitachi
30664, 30573
Hiteker
30672
Humax
31588, 31500
iLo
31348
Initial
30717
Insignia
32095, 31268, 30675
Integra
31769, 30627, 30571
IRT
30783
JBL
30702
JMB
30695
JSI
31423
JVC
31550, 31275, 31164,
30867, 30623, 30558
jWin
31049
Kawasaki
30790
Kenwood
30534, 30490
KLH
31149, 31020, 30790,
30717
Kloss
30533
Koss
31423, 31061, 30769,
30651
Lasonic
30798, 30627
Lecson
31533
Lenoxx
31127
LG
30869, 30741, 30591
LiteOn
31738, 31656, 31440,
31416, 31158, 31058
Loewe
30741, 30511
Logix
30783
Magnasonic 30675, 30651
Magnavox 31506, 31354, 31268,
30675, 30646, 30539,
30503
Marantz
30675, 30539, 30503
McIntosh
31533, 31273
Medion
30651
Memorex
31270, 30831, 30695
Microsoft
32083, 30522
Minato
30752
Mintek
30839, 30717
Mitsubishi 31521, 30521
Mustek
30730
Downloaded From TV-Manual.com Manuals
DVD and Blu-ray Players
Myryad
30894
NAD
30741
Naiko
30770
NEC
30869, 30785
Nesa
30717
NexxTech
31402
Norcent
31265, 31107, 31003,
30872
Onkyo
31769, 30627, 30503
Oppo
31224, 30575
Optimus
30571
Oritron
30651
Palsonic
30852, 30672
Panasonic 31762, 31641, 30703,
30632, 30571, 30503,
30490
Philco
30675
Philips
32084, 32056, 31506,
31354, 31340, 31267,
31158, 30675, 30646,
30539, 30503
Phonotrend 30699
PianoDisc 31024
Pioneer
31571, 31512, 31460,
30632, 30631, 30571,
30525, 30142
Polaroid
31086, 31061, 31020
Polk Audio 30539
Portland
30770
Presidian
31738, 30675
Proceed
30672
Proscan
30522
Prosonic
30699
ProVision
30778
Qwestar
30651
Radionette 30741
RadioShack 30571
RCA
31769, 30822, 30790,
30717, 30571, 30522
Realistic
30571
Reoc
30752
Revoy
30699
Rio
30869
Rotel
31178, 30623
Rowa
31004
Saba
30651
Sampo
30752, 30698
Samsung
31075, 31044, 30820,
30744, 30573, 30490,
30199
Sansui
30695
Sanyo
30873, 30695, 30675,
30670
Schneider 30783
Schwaiger 30752
Sensory
31158
Science
DVD and Blu-ray Players
Sharp
32250, 31256, 30752,
30675, 30630
Sharper
31117
Image
Sherwood 31077, 31043, 30770,
30633
Sherwood 31077
Newcastle
Shinsonic
30839, 30533
Slim Art
30784
SM Elec30730
tronic
Sonic Blue 31099, 30869, 30783,
30715, 30573
Sony
31536, 31533, 31516,
31431, 31070, 31033,
30864, 30533
Sungale
31074
SVA
30860, 30717
Sylvania
31268, 30675
Symphonic 31268, 30675
TAG
30894
McLaren
Tatung
30770
Teac
30790, 30717, 30571
Technics
30703, 30490
Technika
30770
Technosonic 30730
Tevion
30651
Theta Digital 30571
Thomson
30522, 30511
Tivo
31588, 31512, 31503
Toshiba
31769, 31608, 31588,
31515, 31510, 31503,
31154, 30695, 30573,
30539, 30503
Tredex
30800
Unimax
30770
United
30730
Universum 30591
Urban Con- 30539, 30503
cepts
US Logic
30839
V
31226, 31064
Venturer
30790
Vizio
31226, 31064
Wesder
30699
Xbox
32083, 30522
Yamaha
30646, 30545, 30539,
30497, 30490
Yamakawa 30872
Zenith
30869, 30741, 30591,
30503
Zeus
30784
Zoece
31265
Appendices
75
Appendix B: HDMI Control of CEC Devices
Many new HDMI devices have a feature called Consumer Electronics Control (CEC) or HDMI Control. HDMI Control allows one device, such as the TV, to
control other devices, such as an A/V receiver or disc
player. Use of CEC is optional.
Each manufacturer chooses which CEC functions to
support so it is difficult to predict which devices and
features are compatible with Mitsubishi’s HDMI Control. You may find that CEC functions for a specific device are
limited.
To use HDMI Control, you must enable it in both
the TV and the device.
• In the TV. Enable HDMI control from the New
Device Found screen or from the Inputs > HDMI
Control menu.
• In the Device. Most devices with HDMI CEC compatibility let you turn it on or off in the device menus,
where it is typically listed as “HDMI Control.”
4. If prompted for a name,
highlight the name you want
to assign the device.
5. Highlight On.
7. Highlight EXIT and press ENTER to close the New
Device Found screen.
Note: At any time after completing Auto Input Sensing, you can set the TV’s HDMI control on or off
in the Inputs > HDMI Control menu.
8. 153 or 249 Series. To supplement HDMI control
with NetCommand IR control, see page 55.
Enabling HDMI Control of CEC Devices
To ensure proper detection
• Power on HDMI devices before connecting them to
the TV.
• Connect and set up HDMI devices one at a time.
1. Power on the device and allow it to complete the
2.
3.
power-on sequence (boot up). Stop any playback.
Connect the device to one of the TV’s HDMI inputs.
When the TV detects the connection, the New
Device Found screen will appear.
Note: See “If the New Device Found Screen Displays
No HDMI Control Option” on this page if there is
no HDMI Control option.
New Device Found screen with HDMI Control option.
This screen displays only if the device’s HDMI Control is
enabled.
Downloaded From TV-Manual.com Manuals
If the New Device Found Screen
Displays No HDMI Control Option
If the New Device Found screen shows no option for
HDMI Control, one of these conditions applies:
• HDMI Control is turned off in the menus of the
new device
Action:
a. Highlight EXIT and press ENTER to close the
New Device Found screen.
b. Display the device’s setup menus and enable
the device’s CEC capabilities.
c. Wait for the TV’s New Device Found screen
to appear again.
d. If the New Device Found screen does not
appear, power off the device. Power on the
device and wait for the New Device Found
screen to display with the HDMI Control
option.
• The device does not have CEC compatibility
Action:
-- Control the device with its own remote
control or program the TV’s remote control to
operate the device.
-- 153 and 249 Series. Use the TV’s
NetCommand IR control (page 55).
76
Appendices
HDMI Control of an HDMI A/V
Receiver and Connected Devices
Note: Connect the A/V receiver to the TV with an
HDMI cable before making other connections.
R
AVR AUDIO OUTPUT
L
1. Enable HDMI Control for the A/V receiver as
2.
3.
4.
5.
described in “Enabling HDMI Control of CEC
Devices” on the previous page.
Power on the HDMI device you wish to connect to
the A/V receiver (such as a disc player, cable box,
or satellite receiver). Allow the device to complete
L
R
AUDIO if
the power-on sequence (boot up). Stop playback
the device starts playing.
Connect the device to the A/V receiver with an
HDMI cable.
Select the device’s HDMI input on the A/V receiver’s front panel controls or remote control.
When the TV detects the connection, the New
Device Found screen will appear.
Note: If the TV is unable to detect the device, either
the device’s CEC capability is not enabled or
the device is not CEC compatible. Enable
HDMI control through the device’s menus
before continuing. You may need to temporarily connect the device directly to the TV to view
device menus.
6. Highlight On.
7. Highlight EXIT and press ENTER to close the New
8.
Device Found screen.
Optional: Connect the TV’s DIGITAL AUDIO
OUTPUT to an input on the A/V receiver. Use this
additional connection if:
• You want the ability to switch between the A/V
receiver speakers and the TV speakers.
• You want to use the A/V receiver to listen to
devices connected to the TV only, e.g., an
antenna input or camcorder.
9. 153 Series. If desired, perform NetCommand IR
Learning to supplement CEC functions. You must
first connect and place IR emitters for the devices. See page 55.
Downloaded From TV-Manual.com Manuals
TV
Optional
digital audio
cable
HDMI cable
A/V receiver
with HDMI
output
HDMI OUT
L
R
ANALOG AUDIO IN
HDMI cables
DIGITAL
AUDIO IN
VCR
High-definition
DVD player
DVD player
Cable box
Connecting HDMI devices. The optional digital audio
connection allows you to hear audio through the A/V
receiver from devices connected to the TV only.
77
Appendices
Resolving CEC Conflicts
Using HDMI Control
Because each manufacturer selects which CEC functions to support, some devices can conflict with other
devices. If control conflicts arise, you can:
• Turn off TV control of an individual CEC-enabled
device (see below).
• Turn off CEC in the setup menu of one of the
devices.
As an example of using HDMI Control, press PLAY on
the device itself to:
• Power on the TV
• Switch to the device (no need to display the
Activity menu)
• Begin play of the device
Turning Off the TV’s HDMI Control of a CEC Device
Test your equipment with the TV’s remote control to
find additional supported commands. See the table
below for commands that may be available, depending
on the individual device.
1. Press MENU on the TV remote control.
2. Highlight Inputs > HDMI Control and press ENTER
to open the menu.
Direct Keys
3. Move to the device name and press
CEC-enabled VCR, DVD, and DVR functions that
may be available:
4.
Record/
Playback
to select
Off to turn off the TV’s ability to control the device.
Press MENU to clear the menu.
Menu
Navigation
Channel Tuning
Other
CHANNEL UP/DN
Guide
Enter
Digits 0–9, CANCEL
MENU
CANCEL
(to cancel)
ENTER
Inputs > HDMI Control menu
Removing an HDMI Device
1. Power off the device.
2. Disconnect the HDMI cable.
3. Press MENU on the TV remote control to enter the
4.
5.
6.
TV main menu.
Highlight Inputs > Name and press ENTER to open
the menu.
Select Delete from the HDMI input names.
Press MENU to clear the menus.
If you have a CEC-enabled A/V receiver, CEC-enabled
devices connected to the A/V receiver with an HDMI
cable may also be controllable. They can be selected
from the TV’s Activity menu.
CEC-enabled A/V receiver functions that may be
available:
• Try the VOLUME UP/DOWN, MUTE, and menu-navigation
keys.
• To open the A/V receiver menu, follow these steps:
1. While watching TV, press More then 9 (AUDIO).
2. Press until the Speakers option displays.
3. Press to select AVR as the source.
4. Press MORE and then 1 (MENU) to display the
menu.
The MORE Menu and HDMI Control
Press MORE on the TV’s remote control to see a menu
of additional supported functions for the current
CEC-enabled device. To issue a command, press the
number key indicated in the menu.
Inputs > Name menu with Delete selected for HDMI-3.
MORE key: Sample menu for
a CEC-enabled DVD player
Downloaded From TV-Manual.com Manuals
78
Appendices
Appendix C: TV Care
Cleaning Recommendations
General Cleaning Precautions
Normally, light dusting with a dry, non-scratching duster
will keep your TV clean. If cleaning beyond this is
needed, please use the following guidelines:
•
First, turn off the TV and unplug the power cord from
the power outlet.
•
•
Top and Sides of the TV
•
•
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using
a vacuum cleaner with a brush attachment.
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel, microfiber, or a clean
cloth diaper, lightly moistened with water. Dry with
a second dry, soft, non-abrasive cloth.
•
•
DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it gently.
Care of the Remote Control
Remote Control Tips
•
•
•
•
•
For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
• Glossy Surfaces: Take special care when cleaning
the TV’s glossy surfaces.
-- Always shake or brush the cleaning cloth first to
remove any dirt particles.
-- Wipe the glossy areas gently, without applying
pressure.
-- If necessary, lightly dampen the cloth with
water. Use no chemical or abrasive cleaners.
LCD Screen Cleaning
IMPORTANT
DO NOT apply any type of liquid to the surface of
the TV screen.
•
•
•
Use only a soft, dry cloth to clean the LCD
screen. Do not use any liquids.
Wipe the screen gently with an up and down
motion.
Clean the entire screen evenly, not just sections of
the screen.
Downloaded From TV-Manual.com Manuals
•
•
•
•
For longer life, use alkaline batteries.
Do not mix old and new batteries.
Be within 20 feet of the equipment.
Do not press two or more keys at the same time
unless instructed to do so.
Do not allow the unit to get wet or become heated.
Keep the unit out of direct sunlight.
Avoid dropping on hard surfaces.
Do not use harsh chemicals to clean. Use only a
soft, lightly moistened cloth.
Resetting the Remote Control
If TV mode is selected and the TV does not respond
properly, reset the remote control.
1. Press and hold POWER for several seconds until the
mode indicator blinks twice and goes off.
2. Release the POWER key.
3. Press keys 0 0 9 3 5 and the mode indicator will
blink twice when you finish entering the code. When entering the code, pause for a moment
between each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the mode indicator blinks five
times, replace the remote control’s batteries.
Appendices
Appendix D: Bypassing
the Parental Lock
79
Mitsubishi Unisen LCD HDTV
151 Series
153 Series
249 Series
Lock Bypass Instructions Have Been Filed for
Future Reference
Bypassing the Parental Lock
IMPORTANT
Cut along the dotted line and file bypass
instructions in a safe place for future
reference.
Downloaded From TV-Manual.com Manuals
After you set the lock, you must use your pass code to:
• View a locked program
• View the locked TV
• Cancel the lock
• Enter the Lock menus
If you forget your pass code, you can view the locked
TV without entering your pass code. When prompted
for the pass code, press the number 9 and
(LAST)
keys on the TV remote control at the same time. This
process temporarily unlocks the TV.
When entering the Lock menu, you are prompted to
enter a pass code.
•
To change the pass code, press 9 and
(LAST)
at the same time. Either enter a new pass code to
open the Lock menu and make changes or press
BACK to close the menu.
•
If any of the locks are turned on and you exit the
menus when prompted for a new code, the old
code and all lock settings are retained.
•
If all locks are turned off and you exit the menus
when prompted for a new code, then the previous
code is erased.
IMPORTANT
When changing or deleting your pass code,
you must use the remote control included
with this TV. You cannot use a Mitsubishi
remote control from another component or a
“universal” remote.
80
Appendices
This page intentionally left blank
Downloaded From TV-Manual.com Manuals
Appendices
81
Appendix E: Troubleshooting
TV Reset Comparison Guide
You can resolve many common TV problems using the reset
functions described in the following table. See also the
troubleshooting suggestions later in this appendix.
IMPORTANT
Before you change sound or picture settings: If picture
or sound settings seem wrong for a broadcast channel
(a channel from the ANT input, a cable box, or satellite
receiver), first check other channels from the same input
before changing settings. If most other channels from the
same input seem correct, there is likely a problem with the
broadcast rather than with the TV. Use care in this case, as
changes you make to fix problems on individual channels
also affect all other channels on the same input.
Reset Name
When to Use
How to Use
Resulting Action
Format
When the picture
shape seems
incorrect, use
MORE > 0 (FORMAT) to
change the shape of
the picture.
Press the MORE key and then repeatedly press 0 (FORMAT) to cycle
through the available aspect ratios.
The last-used format for a signal
type is memorized for each
input. The next time the same
input and the same signal type is
viewed, the last-used format will
be recalled.
PerfectColor™
Reset
or
PerfectColor™/
PerfecTint™
Reset (153 and
249 Series)
(for the single
input currently
being watched)
When the color
1. While viewing the input to
intensities seem out
be reset, press MENU and
of balance, use the
go to Adjust > Picture+ >
PerfectColor/PerfecTint
PerfectColor.
reset to reset the color 2. Press ENTER to display the
balances to the original
PerfectColor adjustment screen.
factory settings.
3. Press CANCEL to reset the colors.
Both PerfectColor and
PerfecTint are reset at
the same time.
All PerfectColor/PerfecTint
sliders are reset to the
original center position. The
PefectColor/PerfecTint settings
for other inputs remain
unchanged.
A/V Memory
Reset
(for the single
input currently
being watched)
When audio and/
1. While viewing the input to reset,
or video settings for
press MENU and go to Adjust >
a single input seem
Reset.
incorrect, use A/V
2. Press ENTER to highlight the
Memory Reset to return
Reset icon.
the input to the original
3. Press ENTER again to reset.
factory settings.
All Audio and Video settings
for the individual input are
reset except for the Listen To,
Language, audio Balance,
Closed Caption, and Advanced
Picture settings.
A/V Reset
(for all inputs)
To reset audio and
video adjustments for
all inputs to the original
factory settings.
All Audio and Video settings are
returned to the original factory
settings, including Listen To,
Language, audio Balance,
Closed Captions, and Format.
While viewing the TV, press the
control-panel buttons ACTIVITY and
VOLUME DOWN at the same time for at
least two seconds.
Service and Customer Support
Customer Support
Service
• To order replacement or additional remote controls or to purchase an IR emitter cable, visit
our website at www.mitsuparts.com or call
(800) 553-7278.
If you are unable to correct a problem with your TV,
consult your Mitsubishi dealer or Mitsubishi Consumer
Relations at (800) 332-2119.
• DO NOT adjust any controls other than those
described in this Owner’s Guide.
• DO NOT remove the protective back cover of your
TV.
Downloaded From TV-Manual.com Manuals
• For questions:
Call Consumer Relations at 800-332-2119.
E-mail: [email protected]
Website: www.mitsubishi-tv.com
• 249 Series. If you are having difficulty with your
VUDU account, contact VUDU Customer Care at
www.VUDU.com/support.
82
Appendices
Appendix E: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
Channel
Memorization
To erase and
re-memorize channels
on the Ant input.
1. While viewing the TV, press
MENU to display the main menu.
2. Navigate to the Initial> Channel menu.
3. Press ENTER.
4. Highlight the reception mode,
e.g. Ant Air.
5. Highlight Scan.
6. Press ENTER to start channel
memorization.
All previously memorized channels for the antenna input are
erased and a new set of memorized channels is created. To
add or delete individual channels, see Initial > Channel >
Edit menu instructions on page
48.
Lock Menu
Pass Code
To change your Lock
menu pass code
See the cutout page from Appendix D,
page 79.
Allows establishment of a new
code.
Control-Panel
Lock Release
To re-enable the
control-panel buttons
after activation of the
Control-Panel Lock
Press and hold the ACTIVITY button
Allows the control panel to be
on the control panel for ten seconds. unlocked if the remote control is
If the TV is powered off, you can
misplaced.
now press the POWER button to turn
it on.
Auto Input
Sensing for
HDMI
If the New Device
Found screen does
not appear when you
connect an HDMI
device.
1. Disconnect the HDMI device.
The New Device Found screen
2. Delete the HDMI input in the Inputs will display.
> Name menu (see page 50).
3. Power on and connect the new
device.
System Reset
If the TV does not turn
on or off, does not
respond to the remote
control or controlpanel buttons, or has
audio but no video.
Press and hold the POWER button on
the control panel for ten seconds.
The TV will turn off. Power on the
TV and the green LED will flash
quickly for about one minute. The
changes you made most recently,
before using SYSTEM RESET, may
be lost.
TV Reset
To reset all consumeraccessible settings
and all memories to
the original factory
defaults.
1. While viewing the TV, press
MENU to display the TV main
menu.
2. With the main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
Use TV Reset if the TV
3. READ THE ON-SCREEN
can respond to conWARNING AND INSTRUCtrols but TV behavior is
TIONS.
abnormal.
• If you do not wish to use this
CAUTION: All ownerreset, press BACK or MENU to
performed setups and
back out.
adjustments will be
• If you do wish to use the
erased.
reset, press ENTER to erase
all memories and settings.
The TV will start the initialization
process and then turn off. Power on the TV and the front
green LED will start flashing. All
memory and settings outlined in
this Owner’s Guide will need to
be set again.
• VUDU does not
1. Press the MORE Key.
respond to commands. 2. Press the 2 key.
• The selection does not
play (e.g., screen is
black or the “Loading”
messge is frozen on
screen).
The screen will briefly go blank
while VUDU initializes.
This reset does not reset the TV
or any TV settings.
IMPORTANT: Use this reset
only if other
troubleshooting
has been unsuccessful.
VUDU™
Reset VUDU
Connection
(249 Series)
Downloaded From TV-Manual.com Manuals
Appendices
83
Appendix E: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
VUDU
Reset VUDU
Account
Password
(249 Series)
You have forgotten
your account password.
Using a computer, go to
www.VUDU.com.
Reset your account password
from the VUDU website (requires
access to e-mail).
VUDU
Reset Parental
Controls
Passcode
(249 Series)
You have forgotten
your passcode.
Call VUDU Customer Care at
1-888-554-VUDU (8838).
VUDU Customer Care will reset
your passcode.
General TV Operation
Symptom
Remarks
1.
The TV remote control does not work.
•
•
•
•
•
2.
When I try to use the remote control, the
POWER key blinks five times.
Replace the batteries.
3.
TV does not respond to the remote control or •
to control-panel buttons and TV will not power •
on or off.
Unplug the AC power cord for 10 seconds.
Press and hold the POWER button on the control panel to
perform system reset.
4.
When a device is selected from the Activity
menu, the screen is blue or black (no signal
source).
•
•
Make sure the selected device is turned on.
Begin play of the device.
5.
You have forgotten your Lock menu pass code.
See “Bypassing the Parental Lock”, Appendix D.
6.
Rating restrictions are not working.
Open the Lock > Parental Lock menu and:
• Verify that the ratings locks are active.
• Check the Lock Time/Unlock Time to check if rating restrictions are disabled.
• Rating restrictions apply only to content on the ANT input.
7.
On-screen displays appear each time you
change a function.
Normal TV operation.
I have turned on CEC for my HDMI devices
but control is erratic and I wish to disable it.
•
Check that the batteries are fresh and installed correctly.
Check that the control mode on the remote is set to TV.
Be no more than 20 feet from the TV when using the remote control.
Program the remote control to operate the TV or other device.
Reset the remote control.
8.
9.
•
•
Downloaded From TV-Manual.com Manuals
First turn off the TV’s HDMI control for the specific device. Open the Inputs > HDMI Control menu, select the device,
select Off.
Disable CEC on the device itself. See the device’s instructions.
If the problem persists, do the following:
1. Disconnect the device from the TV.
2. Open the Inputs > Name menu and select Delete for the
device.
3. Reconnect the device to the TV and Auto Input Sensing
will recognize the device with CEC disabled.
84
Appendices
Appendix E: Troubleshooting, continued
TV Channels
1.
Symptom
Remarks
The TV takes several seconds to respond to
channel changes.
•
•
•
•
2.
You cannot access a channel.
•
•
•
•
•
•
3.
When ChannelView list is displayed, information appears incomplete
•
•
•
•
It is normal for digital channels to take longer to tune in.
Press ENTER after entering a channel number to avoid
delays.
Use a 4-digit number for an over-the-air digital channel.
Use a 6-digit number for digital cable channels if your cable
service is able to recognize 6-digit channel numbers.
Use number keys instead of CHANNEL Up/Down.
Be sure the channel you want to view is in memory.
Check that the TV is switched to the correct device or
antenna for that channel by pressing the ACTIVITY key.
Make sure the Lock > Parent menu lock is set to Off.
If you cannot tune to a virtual digital channel even though the
TV has already memorized digital channels, tune to the physical channel number used by the broadcaster. The virtual
channel will then be automatically added to memory.
You may be trying to tune to an analog channel that is no
longer broadcasting.
Press INFO to update the display for the highlighted channel.
Program information is displayed only for the currently tuned
channel.
Available information is sent from the broadcaster or cable
provider. No other data is available.
Make sure the TV clock is set correctly.
TV Power On/Off
1.
Symptom
Remarks
TV takes an excessively long time to power
on.
•
•
When powered on, the TV needs time to boot up, just as
does a computer.
For faster power-up, change the Energy setting to Fast
Power On (Initial > Energy menu). With this setting the TV’s power usage when off exceeds ENERGY STAR® recommended levels for a powered-down device.
2.
You cannot program the TV to turn on automatically (Timer function)
•
•
The TV may be locked.
The clock may not be set.
3.
TV turned itself off and the light on the front
panel started to blink.
•
Momentary power fluctuation caused the TV to turn off to
prevent damage. Wait for the green light to stop flashing
and turn the TV on again.
If the TV does not stay on, press the POWER button on the
control panel for at least eight seconds to perform System
Reset. If this happens frequently, obtain an AC line power
conditioner/surge protector.
An unusual digital signal may have been received, triggering a
protection circuit. Wait for the light to stop flashing and turn TV
on.
•
•
4.
TV will not power off.
Downloaded From TV-Manual.com Manuals
Press the POWER button on the control panel for ten seconds
to perform System Reset.
Appendices
85
Appendix E: Troubleshooting, continued
Picture
Symptom
Remarks
1.
Picture does not look like a high-definition
picture.
Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must
subscribe to the provider’s high-definition service. Some overthe-air broadcasts are in high-definition and can be received with
a high-quality antenna suited to your location.
2.
TV has sound but no picture.
•
•
3.
Picture has become dimmer.
Adjust picture brightness and contrast to maximum levels.
4.
There is a large black or gray rectangle on
the screen.
The TV’s analog closed captioning has been set to “text” mode
in the Captions menu. Turn off because there is no text information being broadcast.
5.
You cannot view a picture when playing a
VHS tape.
Check your VCR’s owner’s guide for further troubleshooting.
6.
VCR or DVD player’s on-screen menus jitter
up and down.
Stop playback. Possible cause: Many VCRs and DVD players
provide on-screen menus at only half-resolution that may
appear to jitter up and down.
7.
When viewing a stopped VCR, white lines
are rolling on the screen.
•
•
•
8.
A color program appears as a black and
white image, or the colors are dim, or the
screen is black.
The PerfectColor color balance has been incorrectly set. Reset
the PerfectColor balance.
9.
Picture from an HDMI input is noisy (poor
quality).
Upgrade a Category 1 (unmarked) HDMI cable to a Category 2
high-speed HDMI cable.
10. The image from a computer appears distorted when viewed on the TV.
•
•
Check that all video inputs are plugged in firmly.
Press and hold the POWER button on the control panel for
ten seconds to perform System Reset.
Turn off video mute for the VCR.
Begin playing the tape.
Change the VCR input from Line 1 to the VCR antenna input.
Normal TV operation. The TV does not correct distortion in
the picture from a computer because the correction process
may cut off the edges of the image.
The aspect ratio may be wrong for the image. Press MORE
and then 0 (FORMAT) to change.
Sound
1.
Symptom
Remarks
There is no sound even when the
volume is turned up.
•
•
•
•
•
Downloaded From TV-Manual.com Manuals
Check if the MUTE key is on.
The TV’s “Listen to:” setting may be set to SAP (analog program
from the ANT input) but no SAP is being broadcast.
Check that the Speakers option is set to TV to hear sound from
the TV speakers. Possibly sound is being sent to one of the audio
outputs for an A/V receiver or headphones.
If using an A/V receiver, check that the Speakers option is set to AV
Receiver to hear sound from the A/V receiver speakers.
Press and hold the POWER button on the control panel for 10
seconds to perform System Reset.
86
Appendices
Appendix E: Troubleshooting, continued
Sound
Symptom
Remarks
2.
The sound does not match the screen
picture.
The TV’s “Listen to:” setting may be set to SAP (analog program from
the ANT input).
3.
The sound from my A/V receiver does
not match the screen picture (I should
hear the correct audio from my A/V
receiver).
•
•
Check that DIGITAL AUDIO OUTPUT and/or AVR AUDIO
OUTPUT on TV’s main panel is connected to the A/V receiver.
Without this connection, devices connected only to the TV (and
not the A/V receiver) can be heard only from the TV speakers. Note that this includes the ANT input, a device (such as a
camcorder) connected to the convenience panel, and any other
device sending audio to the TV only.
If using a NetCommand-controlled A/V receiver, NetCommand
may be selecting the wrong A/V receiver audio input. Check the
A/V receiver’s NetCommand setup in the Inputs > AVR menu.
4.
Cannot select an audio-only device; it
does not appear in the Activity menu.
Plug an unused video plug into the Y/VIDEO jack to activate Auto
Input Sensing and make the audio device selectable in the Activity
menu.
5.
Sound is coming from the TV speakers
instead of the A/V receiver.
Disconnect headphones. Connect the TV’s AUDIO OUT to the A/V
receiver and select AV Receiver from the New Device Found screen.
NetCommand IR Control (NetCommand-equipped models only)
Symptom
Remarks
1.
•
Cannot see the menu from the A/V Receiver.
•
•
2.
NetCommand unable to learn specific device
keys.
•
•
•
•
•
Downloaded From TV-Manual.com Manuals
A/V Receiver Set Up for Audio-Only Switching
The A/V Receiver is not connected to any video input of the
TV. To check the A/V Receiver menu, temporarily plug into
an unused input of the TV, such as Input 3. Exit the New
Device Found screen and select Input 3 from the Activity
menu. Press MENU on the A/V receiver’s remote control.
A/V Receiver Set Up for Audio and Video Switching over
HDMI
Use the MENU key on the A/V receiver’s remote control.
A/V Receiver with HDMI Control
Switch the remote control to AUDIO mode. Press the
MORE key and then 1 (Menu).
A/V Device does not use IR format for remote control
signal. ITT and RF formats cannot be learned.
Room lighting may affect the signal. Have the remotes very
close (6 inches or less) to the TV during Learning.
If learning a Mitsubishi remote control, make sure mode is
not set to TV.
Some, but not all, device key functions can be learned by
NetCommand. For example, POWER and PLAY may be
learned, but other functions may not.
The signal from the remote control may not be strong
enough. Insert fresh batteries and try Learning again.
Appendices
87
Appendix E: Troubleshooting, continued
NetCommand IR Control (NetCommand-equipped models only)
Symptom
3.
Remarks
The A/V receiver is the selected audio source •
but there is no sound.
•
A/V Receiver Set Up for Audio-Only Switching
-- Check to see if the A/V Receiver power is turned on.
-- With A/V receiver power turned on, redisplay the Activity menu and press ENTER to allow NetCommand to
correctly select the A/V Receiver input.
-- Incorrect setup in the Inputs > AVR menu. Check the
device connection assigned in the AVR menu.
A/V Receiver Set Up for Audio and Video Switching over HDMI
-- Check to see if the A/V Receiver power is turned on.
-- If the device is connected only to the TV (e.g., on ANT
or a front panel input), verify that the TV’s AUDIO
OUTPUT is connected to the A/V receiver.
-- The A/V receiver is not switching properly because
you have not learned the IR codes for the A/V receiver
inputs to which your devices are connected.
4.
There is no sound from the A/V receiver
for my DVD player or other surround sound
device even though I learned the IR code for
the A/V receiver’s DVD input or other input.
(A/V Receiver Set Up for Audio-Only Switching)
NetCommand A/V receiver setup for the DVD player or digital
surround sound device or other device is not switching properly. See “Automatic Switching (Audio or Audio/Video),” page
63, and perform A/V receiver setup for a digital surround sound
device.
5.
There is no sound or picture from the A/V
receiver for my DVD player or other device
connected to the A/V receiver; the A/V
receiver should be sending video to the TV
over an HDMI cable.
(A/V Receiver Set Up for Audio and Video
Switching over HDMI)
The NetCommand A/V receiver setup is not switching audio
and video inputs properly because you did not “learn” the A/V
receiver’s IR codes for the device inputs. See “Case 3: Automatic Audio and Video Switching via HDMI,” page 65.
6.
I’ve selected my DVD player or other surround sound device in combination with the
TV speakers but hear no sound from the TV
speakers.
•
•
7.
A/V Receiver Set Up for Audio-Only Switching
If you have only an audio connection from the device to the
A/V receiver, a physical audio connection from the device
to the TV is also required.
-- Connect the left and right audio output from the device
to the appropriate TV audio input. Now you can hear
audio from the device through either the TV speakers or
the A/V receiver.
-- To switch audio sources, press MORE 9 (Audio), press
to show the Speakers option, then press to
select AV Receiver or TV.
A/V Receiver Set Up for Audio and Video Switching over HDMI
With your DVD player connected to the A/V receiver, only
video is passed from the A/V receiver to the TV because of
copy-protection restrictions on the HDMI signal
I “learned” the RECORD key for my VCR/DVR Check that the VCR or DVR is receiving a signal directly from
but when I pressed the RECORD key, the
your cable box or satellite receiver.
VCR/DVR did not record anything.
Downloaded From TV-Manual.com Manuals
88
Trademark and License Information
Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Manufactured under license from Cambridge Mechatronics Ltd.
Rapidfire and the 1... logo are trademarks of Cambridge Mechatronics Ltd
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
ENERGY STAR® and the ENERGY STAR mark are registered U.S. marks. ENERGY STAR is a registered mark owned
by the U.S. government.
HDMI™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
Imaging Science Foundation Certified Calibration Controls
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
x.v.Color and the x.v.Color logo are trademarks of Sony Corporation.
VUDU™ is a trademark of VUDU, Inc.
ChannelView™, DeepField™ Imager, Easy Connect™, NetCommand®, PerfectColor™, PerfecTint™, Plush 1080p®
5G, SharpEdge™, Smooth120Hz™ Film Motion, Unisen™ are trademarks of Mitsubishi Digital Electronics America,
Inc.
Network Service Disclaimer
Third party content and services, including without limitation home entertainment services by VUDU, Inc., are
provided in accordance with whatever terms and conditions are established by the third party providers and
agreed to by you. Mitsubishi Digital Electronics America (“MDEA”) has no control over any such third parties or
any agreement you reach with them. MDEA has no control over the networks or transmission facilities by which
content and services are provided by third parties. Your connection to the internet may vary in availability and
quality. Customer service questions are to be directed to the third-party provider, not MDEA.
MDEA DOES NOT WARRANT CONTENT OR SERVICES PROVIDED BY ANY THIRD PARTY, EITHER
EXPRESSLY OR IMPLIEDLY, FOR ANY PURPOSE. MDEA DOES NOT WARRANT THAT ANY THIRD PARTY
SERVICE WILL REMAIN AVAILABLE FOR ANY PERIOD OF TIME OR THAT IT WILL BE SATISFACTORY, UNINTERRUPTED OR ERROR FREE. MDEA EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING
BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
WITH RESPECT TO ANY THIRD PARTY CONTENT AND SERVICES.
MDEA WILL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE, WHETHER IN CONTRACT OR TORT OR
OTHER LEGAL THEORY, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING OUT OF, OR IN CONNECTION WITH, YOUR USE OF ANY CONTENT OR SERVICE THAT IS PROVIDED TO YOU BY ANY THIRD PARTY,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Downloaded From TV-Manual.com Manuals
Trademark and License Information
89
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By
utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software
only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any
violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation
of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license
is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any
provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned
by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software
is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and
treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.
5.
EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software
back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development,
or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in
U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S.
federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN
NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MDEA’S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE
ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s
liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money
paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.
WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects
or other reproductive harm.
Downloaded From TV-Manual.com Manuals
90
Trademark and License Information
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991
Free Software Foundation, Inc.
675 Mass Ave, Cambridge, MA 02139, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the
Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by
the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software
or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate
to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure
that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify
the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is
modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will
not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not
licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this
General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another
language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running
the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of
any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the
most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying
that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print
an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this
License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or
distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above
provided that you also do one of the following:
Downloaded From TV-Manual.com Manuals
Trademark and License Information
91
GNU General Public License, continued
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on
a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing
source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the
source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code
from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights,
from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program
or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work
based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program
or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly
or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as
a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/
donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who
places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you
have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does
not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision
will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD
THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF
DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Downloaded From TV-Manual.com Manuals
92
Warranty
Mitsubishi LCD Flat Panel HDTV Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants to the original purchaser of this LCD Flat Panel HDTV
that if purchased from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of improper workmanship and/or material:
a. Parts. All parts (except any software incorporated into this HDTV) are warranted for a period of one year from the date of the
original purchase at retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for
replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.
b. Embedded Software. MDEA warrants that all software incorporated into this HDTV (the “Embedded Software”) will
perform in accordance with the functional description of Embedded Software in all material respects, but MDEA does not
warrant that the Embedded Software is error-free. The warranty contained in this section shall continue for a period of one
year, from the date of the original purchase from the authorized dealer. If, after prompt notice within the warranty period, MDEA
determines that the Embedded Software has failed to perform in accordance with such functional description in all material
respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then
MDEA shall modify or replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion
may be fulfilled by means of modification or replacement software contained on a replacement memory card for Consumer
installation. The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to your compliance with the terms of the Software License Agreement applicable to this HDTV, and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is
modified or changed in any manner except as specifically authorized by MDEA.
c. Labor. For certain items that are designed to be replaced by the consumer, including (but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, we will provide the labor for a
warranty repair by an authorized MITSUBISHI service center without charge for one year from the original date of purchase at
retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period.
BEFORE REQUESTING SERVICE, please review the TV owner’s guide to insure proper installation and correct customer control adjustment. If the problem persists, please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center whose name and address can be obtained from your MITSUBISHI dealer, by writing to the address provided below, calling MDEA at 800-332-2119, or using the support feature of our
website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your television is
located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If not, you must either
deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation costs
the service center may charge to and from you home. Actual service labor will be provided without charge.
c. Proof of purchase from an authorized MITSUBISHI dealer is required when requesting warranty service. Present your sales
receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER REGISTRATION
CARD IS NOT A CONDITION OF WARRANTY COVERAGE. However, please return the Owner Registration Card so that we can
contact you should a question of safety arise which could affect you.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Cosmetic damage or any other damage where such damage is caused by unauthorized modification, alteration, repairs to
or service of the product by anyone other than an authorized MITSUBISHI service center; physical abuse to or misuse of the
product (or any product damaged by excessive physical or electrical stress); any products that have had a serial number or any
part thereof altered, defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any
damage caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused
by electrical system or damages caused by use of third party mounting brackets or stands. This limited warranty also excludes
service calls where no defect in the product covered under this warranty is found, service calls related to unsatisfactory audio
or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty, all costs,
expenses or any other damages arising from product installation, removal from or re-installation into custom installations or on
Downloaded From TV-Manual.com Manuals
Warranty
93
wall mountings, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness),
other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna, cable
or satellite systems, or service of products purchased or serviced outside the U.S.A. Please consult the operating instructions
contained in the Owner’s Guide furnished with the product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT
ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF
ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF
CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental,
special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the state
where the television was purchased and the laws of such state will govern. In no event shall Mitsubishi have any liability, including with out limitation, for general, consequential, incidental, or special damages for loss, destruction, damage or corruption
of recorded data, media or software resulting from use of this television, or cost of recovery of lost data, media or software
therefore.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
Downloaded From TV-Manual.com Manuals
94
Index
Index
A
Accent Lighting 44
Activity Menu 25
Automatic Generation 51
Change Input Name 50
Customizing 50
NetCommand-Controlled Switching of A/V Receiver Inputs 58
Removing a Disconnected HDMI
Device 50
Anamorphic Picture Format 28
Antenna Input (ANT) 17, 18
Signal Strength for Digital Channels 27
Audio Lock (A/V receiver control) 69
Audio Output Jacks 17, 18
Auto Input Sensing 13
Auto-Off (Sleep Timer) 25
Auto-On (Timer) 47
A/V Receiver
and Speakers Option 42
and TV’s Remote Control 68
Audio Lock 69
Connecting 18, 23, 65, 76
Controlling Sound Volume 26
Disconnecting Analog 26
NetCommand IR Control 61, 62
Controlling a Device Connected
to the A/V Receiver 39, 66
Video and Audio Switching via
HDMI 66
B
Backlight 9, 41
Batteries 7
Blue Glow 44
Brightness (picture adjustment) 41
C
Cable Box
and TV’s Remote Control 68
Connecting 20, 21, 22
Camera Files 31
Captions Menu 46
CEC (Consumer Electronics Control) 6, 39, 75
A/V Receiver 26, 76, 86
Troubleshooting 83
Channels
antennaweb.org 48
Physical/Virtual Channel Numbers 48
Scan (memorize) 12, 48
Troubleshooting 84
ChannelView™ Channel Listings 26
Cleaning 78
Downloaded From TV-Manual.com Manuals
Clock, Set Date and Time 47
Closed Captions 46
Color Adjustments 45
Reset Color 45, 81
Computer
and Display Formats 30
Connecting 29
Contrast 41
Control Panel 11
Control Panel Lock 11, 54
D
Date. See Clock
Default Settings, Returning to 81
DIGITAL AUDIO INPUT 18
DIGITAL AUDIO OUTPUT 18
Digital Camera Video Output 33
DVD Player
and TV’s Remote Control 68
Connecting 20, 21
DVI Device, Connecting 21
E
Energy Usage 48
F
Fast Power On 48
Film Mode 44
Font (digital closed captions) 46
FORMAT (aspect ratio, MORE menu) 28
Freeze Picture (PAUSE key) 10
Front Panel 11
Blue Glow Accent Lighting 44
Full Native 28
G
Game
Game Picture Mode 41
HDMI Cables for Games 18
GUIDE Key
ChannelView 26
HDMI Control 77
NetCommand Control 58, 60
H
HD (High-Definition) Signal) 28
HDMI
Changing Out an HDMI Device
and Auto Input Sensing 13
Connecting an HDMI Device 20
A/V Receiver with HDMI 23
HDMI Cable Categories 18
HDMI Control of CEC Devices 75
HDMI Jack 18
Removing an HDMI Device from
the Activity Menu 50
Headphones
Jack 18
Speakers Option 42
I
INFO Key
ChannelView 26
Status Display 27
USB Menu 31
Internet Video 37
IR Emitter Placement 56
IR NetCommand Output (jack) 19
L
Language
Changing the Menu Language 47
in Digital Programs 43
SAP (Second Audio Program) 43
Learn 50. See also NetCommand IR
Control
Letter Box Image Display 28
Level Sound 43
Listen To 43
Listings (ChannelView) 26
Lock TV
Bypassing the Lock 79
Lock by Ratings 53
Lock by Time 54
Lock Control Panel 54
Preset V-Chip Blocking 52
M
Memorizing Channels 12, 48
Add Single Channel to Memory 48
MP3 Player (audio-only connection) 24
Music Files 31
Mute
Closed Captions 46
MUTE Key 10
Video Mute 44
N
Name (for inputs; Inputs > Name
menu) 50
NetCommand IR Control
About 55
A/V Receiver Control 62
Initial Setup for Most Devices 57
Operating 58
Troubleshooting 86
P
Parental Menu (TV locks) 53
Pass Code
Resetting 79
Setting 52
VUDU Password 83
PAUSE Key 10
PerfectColor/PerfecTint 45
Reset 81
Index
Photo Viewing 32
Picture
Global Picture Adjustments 44
Picture+ Adjustments 45
Picture Menu Adjustments 41
Picture Quality and Film Mode 44
Troubleshooting 85
Subwoofer 26, 42
Surround Sound
External Sound System 23
Simulated Surround Sound 42
Sound Projector 34
TV Audio Outputs 18
System Reset 11, 82
R
Test Picture 44
Time. See Clock
Timer (auto-on) 47
Time Zone. See Clock
Troubleshooting 81
Ratings (TV and Movie) 53
Remote Control
Batteries 7
Keys and Functions 10
Programming Codes (reference
chart) 70
Programming Instructions 69
Reset 78
Reset
A/V Memory Reset (for the current input) 81
A/V Reset (for all inputs) 81
HDMI Auto Input Sensing 13
Pass Code 79
PerfectColor/PerfecTint 81
Remote Control 78
Remote Control Audio Lock 69
System Reset 11
TV Reset Comparison Guide 81
VUDU 82
RS-232C 19
T
U
USB Menu 31, 32
V
V-Chip Ratings
Definitions 53
In Status Display 27
VCR
Connecting 22
Troubleshooting 85
Video Game. See Game
Video Mute 44
Viewing Device. See Activity Menu
VUDU Movie Service 37
VUDU Help 82, 83
W
Wall-Mounting 8
S
Safety Instructions 4, 5
SAP (second audio program) 43
Satellite Receiver
and the Remote Control 68
Connecting 20, 21
Scan (memorize channels) 48
ScreenSaver 44
SD (Standard-Definition Signal) 28
Service and Support 81
Signal Definitions 28
Signal Strength Indicator 27
Sleep Timer 25
Sound
Controlling A/V Receiver Volume
(NetCommand) 62
Audio Lock 69
Level Sound 43
Sound Mode (audio effects) 42
Sound Projector
Connecting Source Devices 20
Sound Projector Setup 34
Speakers Option 42
Standard-Definition Signal 28
Stand Installation 8
Status Display 27
Stereo System. See A/V Receiver
Downloaded From TV-Manual.com Manuals
X
x.v.Color 18, 20, 41
95
Website:
www.mitsubishi-tv.com
E-mail:
[email protected]
For questions, call Consumer Relations at
800-332-2119
To order replacement or additional
remote controls or IR emitter cables,
Visit our website www.mitsuparts.com
or call
800-553-7278
SYSTEM RESET
If the TV does not respond to the remote control,
control-panel buttons, or will not power on/off, press
and hold the POWER button on the control panel for
ten seconds.
The TV will turn off. Power on the TV and the green LED
will flash quickly for about one minute. The changes you
made most recently, before using SYSTEM RESET, may
be lost.
VLP41_VLP41+_IB_e_20090827
© 2009 Mitsubishi Digital Electronics America, Inc.
Downloaded From TV-Manual.com Manuals

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement