Rosslare AC-Q41H Instruction manual

AC-Q4x Family
Vandal Resistant
Stand-Alone controllers
Instruction Manual
Models:
AC-Q41H/HB
AC-Q41SB
AC-Q42H/HB
AC-Q42SB
AC-Q44
December 2006
Table of Contents
Table of Contents
1.
General Information........................................................... 4
1.1
1.2
1.3
1.4
1.5
1.6
1.7
2.
INTRODUCTION ............................................................................... 4
CONTROLLER TYPES...................................................................... 4
BOX CONTENT ................................................................................. 5
ANCILLARY EQUIPMENT .............................................................. 5
TECHNICAL SPECIFICATIONS ...................................................... 6
KEY FEATURES ................................................................................ 7
FRONT PANEL DESCRIPTION ....................................................... 8
Installation ........................................................................... 9
2.1 MOUNTING THE CONTROLLER ................................................... 9
2.2 WIRING THE CONTROLLER ........................................................ 10
2.2.1
Pre-wired Models........................................................................... 10
2.2.2
Terminal Block Models ................................................................. 15
3.
Operation .......................................................................... 19
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.1
3.2.2
3.2.3
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
MODES OF OPERATION................................................................ 19
Normal Mode (Default) ................................................................. 19
Secure Mode .................................................................................. 19
Bypass Mode.................................................................................. 20
USER LEVELS ................................................................................. 20
Normal User................................................................................... 20
Secure User .................................................................................... 21
Master User .................................................................................... 21
SWITCHING OPERATIONAL MODES......................................... 21
From Normal to Secure Mode ....................................................... 21
From Secure to Normal Mode ....................................................... 22
From Normal to Bypass Mode....................................................... 22
From Bypass to Normal Mode....................................................... 23
SPECIAL OPERATIONAL FEATURES......................................... 23
Auxiliary Input & Output............................................................... 23
Request to Exit Button (REX) ....................................................... 23
Tamper Feature .............................................................................. 24
Lockout Feature (Keypad / Card Tamper)..................................... 24
BL-D40 External Sounder ............................................................. 25
AC-Q4x Family, Installation and user Manual
Page ii
Table of Contents
4.
Programming .................................................................... 26
4.1 INTRODUCTION ............................................................................. 26
4.1.1
Entering the Programming Mode .................................................. 28
4.1.2
Exiting the Programming Mode .................................................... 28
4.2 CHANGING THE OPEN CODE ...................................................... 29
4.3 CHANGING THE AUXILIARY CODE .......................................... 29
4.4 CHANGING THE PROGRAMMING CODE.................................. 30
4.5 CHANGING THE NORMAL/SECURE CODE .............................. 31
4.6 CHANGING THE NORMAL/BYPASS CODE............................... 31
4.7 SETTING FAILSAFE/SECURE OPERATION............................... 32
4.8 SETTING AUXILIARY MODES .................................................... 33
4.8.1
General ........................................................................................... 33
4.8.2
Quick Reference Guide for Auxiliary Mode Setting..................... 35
4.8.3
Detailed Reference Guide .............................................................. 36
4.9 KEYPAD HEATER OPERATION................................................... 41
4.10 SETTING THE LOCKOUT FEATURE........................................... 41
4.11 BACKLIGHT and LED BEHAVIOR ............................................... 43
4.12 ENROLLING CODES ...................................................................... 43
4.12.1 Primary Codes Definition .............................................................. 43
4.12.2 Secondary Codes Definition .......................................................... 44
4.12.3 Primary and Secondary Codes Enrolling Methods........................ 44
4.12.4 Standard Method for Codes Enrolling ........................................... 45
4.12.5 Search Method for Codes Enrolling .............................................. 46
4.13 DELETING CODES.......................................................................... 47
4.13.1 Standard Method for Deleting Codes ............................................ 47
4.13.2 Search Method for Deleting Codes................................................ 47
4.14 RELAY CODES ASSIGNMENT ..................................................... 49
4.14.1 Relay Code Assignment using Standard Method .......................... 49
4.14.2 Relay Code Assignment using Search Method ............................. 50
4.15 PIN CODE LENGTH / FACTORY DEFAULT SETTINGS ........... 51
4.16 REPLACING A PROGRAMMING CODE...................................... 52
4.17 REPLACING A NORMAL/SECURE CODE .................................. 52
Appendix A.
Appendix B.
Page iii
Limited Warranty............................................ 53
Technical Support ......................................... 55
AC-Q4x Family, Installation and user Manual
General Information
1.
General Information
1.1
INTRODUCTION
The AC-Q4x series Access Control units are vandal resistant standalone controllers. All the units are water resistant and suitable for
indoor or outdoor mounting. The unit(s) accepts up to 500 users
and allows entry via a personal identification number (PIN) and /
or by presenting a proximity card.
1.2
CONTROLLER TYPES
The different types of control units described in this manual are:
•
•
•
Type 41 is PIN only
Type 42 is PIN and proximity card
Type 44 is PIN and proximity card, with Piezo contacts
Heater
Relay
Current
Backlight
Keypad
Type
AC-Q41H
2A
Standard
AC-Q41HB
2A
Standard
AC-Q41SB
2A
Standard
AC-Q42H
2A
Standard
AC-Q42HB
2A
Standard
AC-Q42SB
2A
Standard
AC-Q44
2A
Piezo
AC-Q4x Family, Installation and user Manual
Proximity
Page 4
General Information
1.3
BOX CONTENT
Before beginning verify that all of the following is in the box, if
anything is missing please report the discrepancy to your nearest
Rosslare Office.
•
•
•
•
•
1.4
One unit
One Drilling Template (Label/Sticker)
One security spline key
One security hex screw
Four mounting screws and wall plugs
ANCILLARY EQUIPMENT
The following ancillary equipment may be required to complete
your installation:
•
•
•
•
•
Electric Lock Strike Mechanism - fail safe (power to lock) or
fail secure (power to open).
Power Supply with Backup Battery - 12 to 24 VDC (from a
regulated power supply) or 16 to 24 VAC (from a
transformer).
Request to Exit (REX) Button (optional) - normally open type;
switch is closed when pressed.
BL-D40 External Sounder (optional) - provides siren, bell, and
chime.
Magnetic Contact (optional) - installed for door monitor
capabilities.
Page 5
AC-Q4x Family, Installation and user Manual
General Information
1.5
TECHNICAL SPECIFICATIONS
AC-Q41H
VDC
VAC
Maximum Input Heater Off
Current (12VDC) Heater On
Standby Input
Heater Off
Current (12VDC) Heater On
Maximum Relay Current
REX Input
Aux. Input
Max. Proximity read range
Proximity Modulation
Proximity card compatibility
LED Indicators
Operating Temperatures
Outdoor Usage
Size
Weight
AC-Q41HB AC-Q42H AC-Q42HB
Input Voltage
AC-Q41SB
AC-Q42SB
AC-Q44
12-24 VDC
12-24 VAC
100mA
130mA
580mA
610mA
40mA
70mA
520mA
550mA
16-24 VAC
125mA
145mA
605mA
625mA
65mA
85mA
545mA
565mA
12-24 VAC
130mA
610mA
70mA
550mA
145mA
625mA
85mA
565mA
16-24 VAC
125mA
N/A
65mA
N/A
2A
Normally Open(Dry Contact)
Normally Open(Dry Contact)
N/A
65 mm (2.5")
N/A
65 mm (2.5")
N/A
ASK at 125 KHz
N/A
ASK at 125 KHz
N/A
26 Bits EM cards
N/A
26 Bits EM cards
Two 3 colored LED (Mode and Door)
-20ºC to +60ºC (-4ºF to +140ºF)
Water resistant, meets IP-54
Weather resistant, meets IP-65, Epoxy potted
H 120 x W 76 x T 27 mm H 4.72" x W 3" x T 1.06"
H 120 x W 76 x T 22 mm H 4.72" x W 3" x T 0.85"
440 gr. 1 lbs.
521 gr.
1.18 lbs.
AC-Q4x Family, Installation and user Manual
Page 6
General Information
1.6
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
KEY FEATURES
500 Users
Water and vandal resistant
Programmable Backlight and active LED control (option “B”)
Three user levels: normal; secure; master
Three modes of operation: normal; bypass; secure
Integrated keypad for PIN entry (Piezoelectric - Q44 only)
Integrated proximity card reader (Q42 and Q44 only)
Selectable PIN code length up to 8 digits
Auxiliary input and auxiliary output
Ten auxiliary modes including: door ajar; forced door; shunt;
door monitor; normal / secure; LED control
Input for Request to Exit (REX) button
Code search feature for easy maintenance of user codes
Internal buzzer
Vandal proof screw (special tool supplied)
Two tri-colored status/programming LED indicators
Built-in case and back tamper protection
Lockout feature on wrong entries (Keypad / Card Tamper)
Bell, chime, siren and strobe features available with BL-D40
Programmable siren time (with BL-D40)
Programmable lock strike release time.
Supplied with mounting template for easy installation
Page 7
AC-Q4x Family, Installation and user Manual
General Information
1.7
FRONT PANEL DESCRIPTION
Controls and indicators of all controller versions are identical. See
Figure 1 (excluding the antenna, which is unique to Q42 and Q44).
Figure 1: Front Panel
AC-Q4x Family, Installation and user Manual
Page 8
Installation
2.
2.1
Installation
MOUNTING THE CONTROLLER
Prior to starting, select the location where the controller unit is to
be mounted. Perform the following steps:
1) Open the controller by loosening and removing the case
security screw at the bottom using the security spline key.
2) Depending on the type of installation, gang box or panel
mount, drill the respective holes in the rear cover. See Figure
2 for details. For gang box mounting, drill two holes marked
“A”. For flat panel mount, drill four holes marked “B”.
Figure 2: Drilling Holes Identification
Note:
The central hole, marked “C” is for routing the wiring to the
controller.
Page 9
AC-Q4x Family, Installation and user Manual
Installation
3)
Use the provided drilling template to accurately locate and
drill the required holes in the wall or panel.
Use the hardware provided to mount the back plate on the
wall or on a gang box. Be sure to route the wiring via the
large center hole in the back plate. Check for level.
Wire the controller according to the type supplied: pre-wired
cable or terminal block terminal, as instructed hereafter.
Once wired, replace the controller back onto its back plate
and secure using tamper-proof screw and special tool,
supplied with the hardware.
4)
5)
6)
2.2
WIRING THE CONTROLLER
The controllers are provided either with a sixty-centimeter, prewired, 10-conductor cable or with a screw-type terminal block.
Specifically:
Pre-wired cabling Models
AC-Q41SB
AC-Q42SB
AC-Q44
2.2.1
Terminal block models
AC-Q41H/HB
AC-Q42H/HB
Pre-wired Models
These controllers come with a 60cm 24-AWG wiring.
Wire according to the following steps:
1)
2)
Cut and strip the conductors to the necessary length.
Splice the controller pigtail wires to the corresponding
ancillary devices and insulate each connection, including
unused wires. Refer to the wiring color guide table below and
to the wiring diagrams, depending on the desired
application:
Wiring the Lock Strike Relay & REX (Figure 3)
Wiring for Auxiliary Input & Output (Figure 4)
Wiring for the BL-D40 External Sounder (Figure 5)
AC-Q4x Family, Installation and user Manual
Page 10
Installation
Wiring Color Guide
Color
Page 11
Description
Red
V input
Black
Ground
Green
REX / BL
White
In / Monitor
Purple
Lock: Com
Gray
Lock: N.O.
Brown
Lock: N.C.
Blue
Aux: Com
Yellow
Aux: N.O.
Orange
Aux: N.C.
AC-Q4x Family, Installation and user Manual
Installation
Figure 3: Pre-Wired Connection for Lock Strike Relay & REX
AC-Q4x Family, Installation and user Manual
Page 12
Installation
Figure 4: Pre-Wired Connection for Auxiliary Input & Output
Page 13
AC-Q4x Family, Installation and user Manual
Installation
Figure 5: Pre-Wired Connection for the BL-D40 External Sounder
AC-Q4x Family, Installation and user Manual
Page 14
Installation
2.2.2
Terminal Block Models
These controllers come with removable terminal blocks that are
pushed on pins on the motherboard of the controllers. Wire
according to the following steps:
3)
4)
Route the wires or cable through the large hole in the back
cover See Figure 6. Connect the terminal blocks as shown.
Wire the cabling according to the following diagrams.
Wiring the Lock Strike Relay & REX (Figure 7)
Wiring for Auxiliary Input & Output (Figure 8)
Wiring for the BL-D40 External Sounder (Figure 9)
Figure 6: Connections to Terminal Blocks
Page 15
AC-Q4x Family, Installation and user Manual
Installation
Figure 7: Terminal Block Wiring of the Lock Strike Relay & REX
AC-Q4x Family, Installation and user Manual
Page 16
Installation
Figure 8: Terminal Block Wiring of the Auxiliary Input & Output
Page 17
AC-Q4x Family, Installation and user Manual
Installation
Figure 9: Terminal Block Wiring of the BL-D40 External Sounder
AC-Q4x Family, Installation and user Manual
Page 18
Operation
3.
Operation
•
•
3.1
Note:
In the Operation chapter, “code” refers to a PIN code or
proximity card depending on the unit you have.
Memory slots can be a proximity card or PIN code depending
on the unit you have.
MODES OF OPERATION
The Control units have three modes of operation. These are
indicated by the color of the Mode indicator:
3.1.1
•
Normal Mode (Default)
Mode indicator is green.
In normal mode, the door is locked until a valid primary code is
presented to the controller.
The controller can only be programmed in normal mode.
3.1.2
•
Secure Mode
Mode indicator is red.
Only secure and master users can access the premises in secure
mode.
A secure user must enter a primary and secondary code to gain
entry. Once the primary code has been entered, the Door
indicator will flash green for 10 seconds. During this time, the
secondary code must be entered. A master user only needs to
enter his code to gain entry.
Page 19
AC-Q4x Family, Installation and user Manual
Operation
3.1.3
•
Bypass Mode
Mode indicator is orange.
In bypass mode, access to the premises is dependent on the Lock
Strike relays; that is, if the relay is programmed for failsafe
operation or fail-secure operation.
When the Lock Strike relay is programmed for fail secure
operation, the door is locked until the star button (Å) is depressed.
When the Lock Strike relay is programmed for failsafe operation,
the door is constantly unlocked.
In case of power failure, once the power is restored, the controller
will return to normal mode, for security reasons.
3.2
USER LEVELS
AC-Q4x series Access Control units accept up to 500 users and
provide entry via the use of codes. Each user is allocated two
memory slots: Memory Slot 1 (primary code) and Memory Slot 2
(secondary code).
The way in which the two memory slots are programmed,
determines a user’s access level and also establishes access is
granted for each of the three modes of operation.
There are three user levels:
3.2.1
Normal User
A normal user only has a primary code and is granted access only
when the controller is in its normal or bypass mode.
AC-Q4x Family, Installation and user Manual
Page 20
Operation
3.2.2
Secure User
A secure user must have a primary and secondary code assigned,
and the two codes must not be the same. The secure user can
gain access in any mode of operation. In normal mode the
secure user must use the primary code to gain entry. In secure
mode, the secure user must first enter the primary and then the
secondary code, in order to gain entry.
3.2.3
Master User
A master user must have identical primary and secondary codes
assigned. The codes are entered with the same proximity card or
the same PIN. The master user can gain access during any mode
of operation by entering their code only once.
3.3
SWITCHING OPERATIONAL MODES
The three modes of operation defined above, can be changed
through a few steps.
3.3.1
From Normal to Secure Mode
The default factory setting for the normal / secure code is 3838.
1) Enter the normal / secure code.
Mode
Door
Green
•
Mode indicator will flash red.
Mode
Door
Red
2) Depress the # key to confirm the Mode
change.
•
Mode indicator is red.
Mode
Door
Red
The auxiliary input of the controller can also be used to switch the
mode of operation from secure to normal and vice versa, if the
auxiliary input is selected it de-activates the Norma/Secure mode
code. Refer to Setting the Auxiliary Mode, paragraph 4.8.
Page 21
AC-Q4x Family, Installation and user Manual
Operation
3.3.2
From Secure to Normal Mode
The default factory setting for the normal / secure code is 3838.
1) Enter the normal / secure code.
Mode
Door
Red
•
Mode indicator will flash green.
Mode
Door
Green
2) Depress the # key to confirm the Mode
change.
•
Mode indicator will turn green.
Mode
Door
Green
The auxiliary input of the controller can also be used to switch the
mode of operation from secure to normal and vice versa, if the
auxiliary input is selected it de-activates the Norma/Secure mode
code. Refer to Setting the Auxiliary Mode, paragraph 4.8.
3.3.3
From Normal to Bypass Mode
By default, there is no normal / bypass code. The normal / bypass
code must first be programmed to use this function. Refer to
paragraph 4.6 to create / modify the normal / bypass code.
1) Enter the normal / bypass code.
Mode
Door
Green
•
Mode indicator will flash orange.
Mode
Door
Orange
2) Depress the # key to confirm the mode
change.
•
Mode indicator will turn orange.
AC-Q4x Family, Installation and user Manual
Mode
Door
Orange
Page 22
Operation
3.3.4
From Bypass to Normal Mode
1) Enter the normal / bypass code.
Mode
Door
Orange
•
Mode indicator will flash green.
Mode
Door
Green
2) Depress the # key to confirm the mode change.
Mode
• Mode indicator will turn green.
Door
Green
3.4
SPECIAL OPERATIONAL FEATURES
Some installation-specific features are exercised, as required by
the system. These features are implemented as shown in Figures 4
thru 9.
3.4.1
Auxiliary Input & Output
For optimum usability in different applications, the controller’s
auxiliary input and output can be configured in ten different
modes of operation. Refer to Setting the Auxiliary Mode, on
paragraph 4.8.
3.4.2
Request to Exit Button (REX)
The REX pushbutton is located within the premises and is used to
open the door from the inside. It is usually located in a convenient
location (e.g.: next to the door or at a receptionist’s desk). The
door chime (if enabled) in the BL-D40 does not sound when the
REX pushbutton is used to open the door.
The function of the REX pushbutton depends on the Lock Strike
relay, whether it is programmed for failsafe or for fail secure
operation.
Page 23
AC-Q4x Family, Installation and user Manual
Operation
Fail Secure Operation: from the moment the REX pushbutton is
depressed, the door will be unlocked until the Lock Strike release
time has elapsed. After this time, the door will be locked, even if
the REX pushbutton has not been released.
Failsafe Operation: from the moment the REX pushbutton is
depressed, the door will be unlocked until the REX pushbutton is
released. In this case the Lock Strike relay only begins its
countdown once the REX pushbutton has been released. This
feature is designed to keep the door open, when used in
conjunction with fire systems.
3.4.3
Tamper Feature
In case the controller is forcibly opened or the controller is
removed from the wall, a tamper event is triggered. A tamper
signal is sent to the BL-D40.
If the BL-D40 External Sounder receives a tamper event signal, it
will activate a tamper output and a strobe light. The siren time
can be easily programmed in the controller from 0 to 9 minutes.
The tamper event can activate the auxiliary output if the
controller is in Auxiliary Mode 3. Refer to the Quick Reference
Guide for Auxiliary Mode Setting table in paragraph 4.8.2 below.
3.4.4
Lockout Feature (Keypad / Card Tamper)
In case the controller is presented with wrong codes, (PIN or Card)
consecutively several times the unit goes into lockout mode.
When a lockout occurs, the controller keypad and reader are deactivated so no codes can be entered until the set lockout period
expires.
AC-Q4x Family, Installation and user Manual
Page 24
Operation
During Lockout, Mode LED is Off, Door LED flashes Red, and the
controller beeps every two seconds.
Refer to programming menu 6 for detailed programming of this
feature.
3.4.5
BL-D40 External Sounder
The BL-D40 External Sounder is designed for indoor use only and
installed within the secured premises. The Sounder can be
powered by a 12 to 24 VDC power supply or by a 16VAC
transformer. The BL-D40 is capable of emitting four different types
of audible and visual alerts: bell, chime, siren and strobe light.
•
•
•
The bell sounds when the controller’s bell button is depressed.
The door chime can be programmed to sound whenever a
valid code is entered as well as for a door held open alert.
The siren can be programmed to sound when the controller is
tampered with (opened or removed from the wall). The
length of the siren can also be programmed in the controller.
The controller communicates with the BL-D40 via a Rosslare
proprietary protocol. If the BL-D40 receives an unrecognized code
over its communication line or communications between the
controller and the BL-D40 are severed, the strobe will flash
repeatedly, until the communication problem has been resolved.
Page 25
AC-Q4x Family, Installation and user Manual
Programming
4.
Programming
•
•
4.1
Note:
In the Programming chapter, “code” refers to a PIN code or
proximity card depending on the unit you have.
When entering a PIN or presenting a proximity card is
mentioned, the meaning may vary between units.
INTRODUCTION
Programming an AC-Q4x series Access Control unit is done solely
via the unit’s keypad-driven Programming Menu System. To reach
the Programming Menu System, the controller must first be placed
into Programming Mode. Refer to Entering Programming Mode,
paragraph 4.1.1
During the manufacturing process, certain codes and settings are
pre-programmed. These settings are the called default factory
settings.
AC-Q4x Family, Installation and user Manual
Page 26
Programming
The table below shows all the programming menus, with default factory codes and settings.
Menu
No.
1
2
3
4
5
6
6
6
6
6
7
8
9
0
Description
Change open code
Change auxiliary code
Change program code
Change normal / secure code
Change normal / bypass code
Change door release time
Define auxiliary inputs / outputs
Enable or disable keypad heater
Set Lockout Feature
Backlight and LED Behavior
Enroll proximity cards, PIN or both
Delete proximity cards or PIN
Code assignment with strike/auxiliary
Return to factory defaults / Change
PIN code Length
4 Digit
5 Digit
2580
0852
1234
3838
0004
2004
3000
4000
5100
-
25802
08520
12341
38383
Default
6 Digit
258025
085208
123412
383838
Page No.
4-8 Digits
25802580
08520852
12341234
38383838
29
29
30
31
31
32
33
41
41
43
43
47
49
51
Table 1 programming Menu
Page 27
AC-Q4x Family, Installation and user Manual
Programming
4.1.1
Entering the Programming Mode
Note:
•
•
•
1)
•
•
The controller must be in normal mode to enter the
programming mode.
The factory default 4-digit programming code is 1234.
If a programming code is not entered within 5 seconds, the
controller will return to its normal mode.
Depress the # key twice, within 0.5 seconds.
Mode indicator will turn off.
Door indicator will turn red.
2) Enter your programming code.
If the programming code is valid, the door
Indicator will turn green and the controller will
enter the programming mode.
4.1.2
Mode
Door
Red
Mode
Door
Green
Exiting the Programming Mode
Note:
•
•
Wrong entries may reset the controller back to its normal mode.
If no key is pressed for 1 minute, while in programming mode,
the controller will exit the programming mode and return to its
normal mode.
To exit the programming mode, depress the # key twice, within 0.5
seconds.
•
•
•
You will hear three beeps.
The door indicator will be off.
The mode indicator will turn green.
Mode
Door
Green
The above indicates that the controller has returned to its normal
mode.
Note:
While enrolling, deleting users, or while in code assignment
mode, depress the # key, twice to exit the programming mode.
AC-Q4x Family, Installation and user Manual
Page 28
Programming
4.2
CHANGING THE OPEN CODE
The open code is mainly used as a method to quickly test the
Lock Strike relay during installation.
The factory 4-digit default setting for the open code is 2580.
For security reasons when the first user is added to the controller or
the auxiliary code is changed, the default open code will
automatically be deleted, non-default codes will not be erased
automatically.
Note:
•
•
•
1)
2)
3)
4)
Open code does not function in secure mode.
Wrong entries: you will hear a long beep and the controller will
return to its normal mode.
Code 0000 will erase and deactivate the open code.
Enter the programming mode.
Depress 1 to enter Menu 1.
•
The Mode indicator will turn red.
Mode
Door
Red
Enter the new code you wish to set as open code.
System returns to its normal mode.
• You will hear three beeps.
Mode
• The Door indicator will turn off.
Green
• The Mode indicator will turn green.
4.3
Green
Door
CHANGING THE AUXILIARY CODE
The auxiliary code is mainly used as a method to quickly test the
Auxiliary relay during installation. The default 4-Digit factory setting
for the auxiliary code is 0852.
For security reasons when the first user is added to the controller or
the open code is changed, the default auxiliary code will
automatically be deleted, non-default codes will not be erased
automatically.
Page 29
AC-Q4x Family, Installation and user Manual
Programming
•
•
•
•
Note:
Auxiliary code does not function in secure mode.
Auxiliary code only works when the auxiliary mode is 0, 1, 8 or 9.
Wrong entries: you will hear a long beep and the controller will
return to its normal mode.
Code 0000 will erase and deactivate the auxiliary code.
1)
2)
Enter the programming mode.
Depress 2 to enter Menu 2.
•
The Mode indicator will turn orange.
3)
4)
Enter a new auxiliary code.
System returns to its normal mode.
• You will hear three beeps.
• The Door indicator will turn off.
• The Mode indicator will turn green.
4.4
Mode
Door
Mode
Green
Door
Orange Green
Mode
Door
Green
CHANGING THE PROGRAMMING CODE
Note:
•
•
1)
The code 0000 is not valid; thus, the programming code cannot
be erased.
Wrong entries: you will hear a long beep and the controller will
return to its normal mode.
Enter the programming mode.
Mode
Door
Green
2)
3)
4)
•
Depress 3 to enter Menu 3.
The Mode indicator will turn green.
Enter the new programming code.
System returns to its normal mode.
• You will hear three beeps.
• The Door indicator will turn off.
• The Mode indicator will turn green.
AC-Q4x Family, Installation and user Manual
Mode
Door
Green Green
Mode
Door
Green
Page 30
Programming
4.5
CHANGING THE NORMAL/SECURE CODE
Note:
•
•
•
1)
When the auxiliary mode is 1, 2, 3 or 4, the auxiliary input takes
priority over the normal/secure code.
Wrong entries: you will hear a long beep and the controller will
return to its normal mode.
Code 0000 will erase and deactivate the normal/secure code.
Enter the programming mode.
Mode
Door
Green
2)
3)
4)
•
Depress 4 to enter Menu 4.
The Mode indicator will flash red.
Enter the new Normal/Secure code.
System returns to its normal mode.
• You will hear three beeps.
• The Door indicator will turn off.
• The Mode indicator will turn green.
4.6
Mode
Door
Red
Mode
Green
Door
Green
CHANGING THE NORMAL/BYPASS CODE
The normal / bypass code is also used to turn the door chime off
and on. Chime only functions with the BL-D40 External Sounder.
Note:
•
•
•
1)
The chime is only heard when the Lock Strike relay is activated
by a valid code entry.
Wrong entries: you will hear a long beep and the controller will
return to its normal mode.
Code 0000 will erase and deactivate the normal/bypass code.
Enter the programming mode.
Mode
Door
Green
2)
•
Depress 5 to enter Menu 5.
The Mode indicator will flash orange.
Page 31
Mode
Door
Orange Green
AC-Q4x Family, Installation and user Manual
Programming
3)
Hereafter, are four different ways to program the normal /
bypass code and door chime.
a. Disable both Bypass Code and the
0 0 0 0
door chime.
Enter the code 0000.
b. Disable Bypass Code and enable the
0 0 0 1
door chime.
Enter the code 0001.
c. Enable Bypass Code and disable the
? ? ? 0
door chime.
Enter any code ending with 0.
d. Enable Bypass Code and enable the
? ? ? 0
door chime.
Enter a code not ending with 0.
4) System returns to its normal mode.
• You will hear three beeps.
Mode
Door
• The Door indicator will turn off.
Green
• The Mode indicator will turn green.
4.7
SETTING FAILSAFE/SECURE OPERATION
In this paragraph, the failsafe / fail secure operation of the door
lock and the door lock strike release time are set. Setting the
sounding period for the siren feature requires a BL-D40 External
Sounder.
1)
Enter the programming mode.
2)
•
Depress 6 to enter Menu 6.
The Mode indicator will flash green.
AC-Q4x Family, Installation and user Manual
Mode
Door
Green
Mode
Door
Green Green
Page 32
Programming
3)
Construct a code using instructions hereafter.
?
?
?
?
First Digit
For fail secure operation, the first digit is set to 0.
For failsafe operation, the first digit is set to 1.
Second Digit
Siren time, enter any number from
0 to 9 (minutes).
Third and Fourth Digits
The Lock Strike is to be released after the
number of seconds entered (1 to 99).
For example 0 5 1 2 means: fail secure operation (0), with5 minutes
siren time (5) and a 12-second Lock Strike release time (12).
4)
•
•
•
System returns to its normal mode.
You will hear three beeps.
The Door indicator will turn off.
The Mode indicator will turn green.
4.8
Mode
Door
Green
SETTING AUXILIARY MODES
4.8.1
General
The default auxiliary setting is 2004.
1)
Enter the Programming Mode.
Mode
Door
Green
2)
•
Depress 6 to enter Menu 6.
The Mode indicator will flash green
Page 33
Mode
Door
Green Green
AC-Q4x Family, Installation and user Manual
Programming
3) Construct a code using the instructions hereafter.
The Quick Reference Guide for Auxiliary Mode
2
?
?
?
Setting Table provides a quick reference listing for the
auxiliary modes and settings.
Auxiliary Mode
Auxiliary Setting
Note:
Auxiliary Relay activation is subject to users' Auxiliary code
assignment (Excluding Shunt, which is activated by all users), for
more details see paragraph 4.14 RELAY CODES ASSIGNMENT.
Auxiliary Mode
In addition to the Lock Strike relay and the Lock Strike REX, the
controller features an auxiliary output relay and an auxiliary input,
whose function is established by the auxiliary mode selection (0
thru 9).
The auxiliary mode also determines if the auxiliary output relay is
set for failsafe or for fail secure operation.
For a more detailed explanation on each auxiliary mode, refer to
the Auxiliary Mode Reference table below.
Auxiliary Settings
Each of the auxiliary modes has a two-digit setting which affects
the operation of the related relay(s).
4)
•
•
•
System returns to its normal mode.
You will hear three beeps.
The Door indicator will turn off.
The Mode indicator will turn green.
AC-Q4x Family, Installation and user Manual
Mode
Door
Green
Page 34
Programming
4.8.2
Quick Reference Guide for Auxiliary Mode Setting
Auxiliary
Mode
0
AUX REX
1
Normal/Secure
switch
Normal/Secure
switch
Normal/Secure
switch
Normal/Secure
switch
Door Monitor
Door Monitor
Door Monitor
LED control –
Green
LED control - Red
2
3
4
5
6
7
8
9
Page 35
Auxiliary Input
Function
Auxiliary
Output
Activated by
Auxiliary
Relay
Valid code or
AUX REX
Valid code
N.O.
N.O.
Star button (Å)
N.O.
Tamper event
N.C.
Direct shunt
N.O.
Shunt
Forced door
Door ajar
Valid code
N.C.
N.C.
N.C.
N.O.
Valid code
N.O.
Auxiliary Settings
(in seconds)
01 to 99 Aux. relay release time
00 Aux. relay toggle
01 to 99 Aux. relay release time
00 Aux. relay toggle
01 to 99 Aux. relay release time
00 Aux. relay toggle
01 to 99 Aux. relay release time
00 Aux. relay tamper activated
01 to 99 Shunt time
01 to 99 Maximum shunt time
01 to 99 Forced delay
01 to 99 Ajar delay
01 to 99 Aux. relay release time
00 Aux. relay toggle
01 to 99 Aux. relay release time
00 Aux. relay toggle
AC-Q4x Family, Installation and user
Manual
Programming
4.8.3
Detailed Reference Guide
The following are brief descriptions of each auxiliary mode. To
implement the features of each mode, refer to Setting the
Auxiliary Mode, paragraph 4.8.1.
AUXILIARY MODE 0
Auxiliary input function: Activates the auxiliary output
Auxiliary output activated by: Valid user code, Auxiliary code,
Auxiliary input
E.g. In auxiliary mode 0, the controller can function as a two-door
controller. The auxiliary relay is to be attached to the lock on the
second door. The auxiliary setting defines the door open time for
the second door. The auxiliary input is to be attached to the REX
pushbutton for the second door. Door Monitor input feature for
the second door is not enabled when using this mode.
AUXILIARY MODE 1
Auxiliary input function:
Toggles normal/secure modes
Auxiliary output activated by: Valid user code, Auxiliary code
E.g. In auxiliary mode 1, the controller can function as a two-door
controller. The auxiliary relay is to be attached to the lock on the
second door. REX feature for the second door is not enabled
when using this mode.
The auxiliary setting defines the door open time for the second
door. The auxiliary input can switch the mode of operation of the
controller between normal and secure mode. By connecting a
switch timer or alarm system output to the auxiliary input, the
controller can be automatically switched from normal mode
(during office hours) to secure mode (after office hours).
AC-Q4x Family, Installation and user Manual
Page 36
Programming
AUXILIARY MODE 2
Auxiliary input function:
Toggles normal/secure modes
Auxiliary output activated by: Star Button (*)
E.g. In auxiliary mode 2, the auxiliary relay can function as a
general purpose time switch that can be activated when the star
button (Å) is depressed. The auxiliary setting establishes for how
long the auxiliary relay is to be activated. The auxiliary input can
switch the mode of operation of the controller between normal
and secure mode. By connecting a switch timer or alarm system
output to the auxiliary input, the controller can be automatically
switched from normal mode (during office hours) to secure mode
(after office hours).
AUXILIARY MODE 3
Auxiliary input function:
Toggles normal/secure modes
Auxiliary output activated by: Alarms
E.g. In auxiliary mode 3, the auxiliary output is activated if the
controller is tampered; that is, if the case is forcibly opened or
removed from the wall. The auxiliary input can switch the mode of
operation of the controller between normal and secure mode. By
connecting a switch timer or alarm system output to the auxiliary
input, the controller can be automatically switched from normal
mode (during office hours) to secure mode (after office hours).
Page 37
AC-Q4x Family, Installation and user Manual
Programming
AUXILIARY MODE 4
Auxiliary input function:
Toggles normal/secure modes
Auxiliary output activated by: direct shunt (explanation below)
E.g. In auxiliary mode 4, the controller is capable of bypassing an
alarm zone by shunting an alarm system’s door sensor. The
auxiliary output is to be wired in parallel to the door sensor output.
When in use, the auxiliary output is normally open and the door
sensor functions normally. When a valid code is entered, the
auxiliary relay shunts the door sensor for the duration of the shunt
time, as defined by the auxiliary setting. If the door is left open
longer than the shunt time, an alarm will be triggered.
AUXILIARY MODE 5
Auxiliary input function:
Door Monitor
Auxiliary output activated by: Shunt (explanation below)
E.g. In auxiliary mode 5, the controller is capable of shunting an
alarm system. In this mode, the auxiliary input is to be wired to the
magnetic contact switch on the door. The auxiliary relay is wired
to the alarm system. Without a valid code entered, the auxiliary
relay will match the condition of the magnetic contact switch; if
the door opens, the auxiliary relay will open; if the door closes, the
auxiliary relay will close. When a valid code is entered, a count
down for maximum shunt time, as defined by the auxiliary setting,
begins; if the door is not closed before the maximum shunt time,
the alarm will be triggered.
AC-Q4x Family, Installation and user Manual
Page 38
Programming
AUXILIARY MODE 6
Auxiliary input function:
Door Monitor
Auxiliary output activated by: Forced entry
E.g. In auxiliary mode 6, the controller can trigger the auxiliary
relay if the door has been forced. If the Siren Settings is enabled
the siren will be activated.
In this mode, the auxiliary input functions as a door monitor switch
and is wired to the magnetic contact switch on the door. The
auxiliary relay is to be wired to the alarm system. If the door is
forced open, the controller will wait for the period of the forced
door delay time to elapse and then, it will activate the auxiliary
relay. The auxiliary setting sets the forced door delay period.
AUXILIARY MODE 7
Auxiliary input function:
Door Monitor
Auxiliary output activated by: Door Ajar (door held open)
E.g. In auxiliary mode 7, the controller can trigger the auxiliary
relay, if it detects that the door has been held open (ajar) too
long. In this mode the auxiliary input functions as a door monitor
switch and is wired to the magnetic contact switch on the door.
The auxiliary relay is to be wired to the alarm system. If the door is
opened, the controller will wait for the door ajar delay time to
elapse and if the door does not close prior to the end of this
period, the controller will activate the auxiliary relay. The auxiliary
setting defines the door-ajar time.
If the BL-D40 External Sounder is connected in the system and a
door-ajar event occurs, the BL-D40 will chime every few seconds
for 1 minute or until the door is closed.
Page 39
AC-Q4x Family, Installation and user Manual
Programming
AUXILIARY MODE 8
Auxiliary input function:
Green LED control
Auxiliary output activated by: Valid user code, Auxiliary code
E.g. In auxiliary mode 8, the controller can function as a two-door
controller and also provide indicator functionality control. The
auxiliary relay is connected to the lock on the second door. The
auxiliary setting defines the door open time for the second door.
The auxiliary input is used to control the Door indicator. If the
auxiliary input is open, the indicator will flash green; if the auxiliary
input is closed, the Door indicator will flash red.
Note:
This mode takes control of the Door indicator LED.
The indicator LED will not be lit when:
1. A valid code is entered
2. While in secure mode, when waiting for a secondary code.
AUXILIARY MODE 9
Auxiliary input function:
Red LED control
Auxiliary output activated by: Valid user code, Auxiliary code
E.g. In auxiliary mode 9, the controller can function as a two-door
controller and also provide indicator functionality control. The
auxiliary relay is connected to the lock on the second door. The
auxiliary setting defines the door open time for the second door.
The auxiliary input is used to control the indicator. If the auxiliary
input is open the Door indicator will flash red; if the auxiliary input is
closed the Door indicator will flash green.
Note:
This mode takes control of the Door indicator LED.
The indicator LED will not be lit when:
1. A valid code is entered
2. While in secure mode, when waiting for a secondary code.
AC-Q4x Family, Installation and user Manual
Page 40
Programming
4.9
KEYPAD HEATER OPERATION
⌦ NOT APPLICABLE FOR AC-Q44 (without keypad heater)
The controllers contain a built-in keypad heater. Once the heater
circuitry is activated, the heater will turn on when the ambient
temperature drops to 4±1°C and will remain on until the keypad
temperature rises to 7(+2 or -1)°C.
When the heater is on, the controller can operate down to an
ambient temperature of -20°C. When the heater is disabled, the
lowest operating temperature is 0°C.
The default setting for the keypad heater is disabled state (3000).
1)
2)
Enter the programming mode.
Depress 6 to enter Menu 6.
• The Mode indicator will flash green.
3)
Mode
Door
Green Green
Construct a code using the following
instructions:
3
0
0
?
To disable the heater, the fourth digit is set to 0.
To enable the heater, the fourth digit is set to 1.
4.10
SETTING THE LOCKOUT FEATURE
In case the controller is presented with wrong codes, (PIN or Card)
consecutively several times the unit goes into lockout mode.
When a lockout occurs, the controller keypad and reader are
locked so no codes can be entered until the set lockout period
expires.
Page 41
AC-Q4x Family, Installation and user Manual
Programming
During Lockout, Mode LED is Off, Door LED flashes Red, and the
controller beeps every two seconds.
The default setting for the Lockout Feature is 4000 (Lockout
Disabled)
Note:
Using the lockout feature is highly recommended, especially
when selecting to use short PIN code length (4 or 5 digits).
1)
2)
3)
Enter the programming mode.
Depress 6 to enter Menu 6.
• The Mode indicator will flash green.
Construct a code using the following
instructions:
Mode
Door
Green Green
4
?
?
?
Set the number of wrong code
attempts, which will cause Lockout
between 0 and 9 attempts.
Sets the Duration of the lockout,
between 00 and 99, the value is
multiplied by ten, resulting in 0-990
seconds
AC-Q4x Family, Installation and user Manual
Page 42
Programming
4.11 BACKLIGHT and LED BEHAVIOR
⌦ APPLICABLE FOR AC-Q4xHB/SB MODELS ONLY (backlight)
The controller allows you to define the way the units' Backlight as
well as the Mode and Door LEDs will work.
To define the Backlight and LEDs operation:
1)
2)
Enter the programming mode.
Depress 6 to enter Menu 6.
• The Mode indicator will flash green.
3)
Door
Green Green
Construct a code using the following
instructions:
the first digit is five indicating the backlight
and Led option
the second key can be 0-3 indicating the
type of activity
• Option 0 - LED Active / Backlight Off
• Option 1 - LED Active / Backlight On
(default)
• Option 2 - LED and Backlight Off, both
activated on any key press for ten seconds.
• Option 3 - LED Active / Backlight Dimmed,
backlight activated on any key press for
ten seconds.
4.12
4.12.1
•
Mode
5
?
0
0
ENROLLING CODES
Primary Codes Definition
Primary codes can only be enrolled to an empty user slot, a
slot with no existing primary code in the controller’s memory.
Page 43
AC-Q4x Family, Installation and user Manual
Programming
•
•
•
A primary code must be unique; for instance, one user’s
primary code may not be the same as that of another user.
Primary codes cannot be the same as system codes, such as:
the normal / secure code or the open code.
Users possessing a primary code can gain entry during
normal and bypass modes.
4.12.2
•
•
•
•
•
Secondary Codes Definition
Secondary codes can only be enrolled to a user slot that
already includes a primary code.
A Secondary code need not be unique; for instance, one
user’s Secondary code may be the same as that of another
user.
Secondary codes cannot be the same as any system codes,
such as: the normal / secure code or the open code.
Users possessing secondary codes can gain entry in any
mode of operation.
A Secondary code can be the same as the primary code of
any user.
4.12.3
Primary and Secondary Codes Enrolling Methods
There are two methods used to enroll primary and secondary
codes: the standard method and the code search method.
1)
2)
The standard method is used when the user slot number, for
the user you wish to program, is known. You can program
both primary and secondary codes using this method.
The code search method is mainly used when enrolling a
secondary code and the user’s slot code is unknown. The
code search method will function only if a user’s primary
code is already enrolled and the secondary code is not.
AC-Q4x Family, Installation and user Manual
Page 44
Programming
4.12.4
1)
Standard Method for Codes Enrolling
Enter the programming mode.
Mode
Door
Green
2)
•
Depress 7 to enter Menu 7.
The Door indicator will turn orange.
Mode
Door
Orange
3)
4)
5)
Enter the 3-digit user slot number into the memory
? ? ?
(from 001 to 500) so as to enroll a primary or
secondary code.
For example, the user slot 003 represents user no. 3.
At this time three possibilities exist:
a. If the selected slot has no primary code, the Mode
indicator will flash green, indicating
Mode
Door
that the controller is ready to
Green Orange
accept a primary code.
b. If the selected slot already has a primary code, but no
secondary code, the Mode
Mode
Door
indicator will flash red, indicating
Red Orange
that the controller is ready to
accept a secondary code.
c. If the selected slot already has a primary and secondary
code, a long beep will be heard and the controller will
return to its normal mode.
Enter the code to be assigned as the primary or secondary
code for this slot number.
If the code that is entered is valid, the Mode indicator will
cease flashing and the controller is ready for the next 3-digit
slot number (step 3) or depress the # key to move to the next
slot number (step 4). If you do not wish to continue enrolling
codes, depress the # key twice and the controller will return
to its normal mode.
Page 45
AC-Q4x Family, Installation and user Manual
Programming
4.12.5
Search Method for Codes Enrolling
The code search method enables to quickly enroll a secondary
code for a user whose primary code is known and whose slot
number is unknown.
1)
2)
Enter the programming mode.
Depress 7 to enter Menu 7.
•
The Door indicator will turn orange.
3)
5)
The Door indicator will flash orange.
The controller is now waiting for the
primary code of the user.
Door
Green
Mode
Door
Orange
Enter the 3-digit user slot number 000.
•
4)
Mode
Mode
Door
Orange
Enter the primary code belonging to the user who needs a
secondary code.
Mode
Door
•
The Mode indicator will flash red.
Red Orange
If the primary code entered is not
valid, a long beep will sound and the controller will wait
for a valid primary code.
Enter the code to be used as the secondary code.
If the secondary code is valid, the controller will beep three
times and return to its normal mode.
If the secondary code is invalid, the controller will produce a
long beep and will wait for a valid secondary code to be
entered.
AC-Q4x Family, Installation and user Manual
Page 46
Programming
4.13
DELETING CODES
There are two methods to delete primary and secondary codes: a
standard method and a search method. When deleting a user
slot, both the primary code and the secondary code are erased.
Note:
It is recommended that a record be kept of added and deleted
users. This makes it easier to keep track of user slots’ status
(empty or not)
4.13.1
1)
Standard Method for Deleting Codes
Enter the programming mode.
Mode
Door
Green
2)
3)
4)
•
•
Depress 8 to enter Menu 8.
The Mode indicator will turn red.
Mode
Door
Red
Orange
Enter the 3-digit user slot code to be deleted.
? ? ?
The Mode indicator will flash red, indicating the
Mode
Door
controller is waiting for a
programming code to confirm the
Red Orange
deletion.
If the user slot is empty, a long beep will be heard and the
controller will return to its normal mode.
Enter your programming code to confirm the deletion.
If the programming code is valid, three beeps will be heard
and the controller will return to its normal mode.
If the programming code is invalid, a long beep will be heard
and the controller will return to its normal mode.
4.13.2
Page 47
Search Method for Deleting Codes
AC-Q4x Family, Installation and user Manual
Programming
1)
Enter the programming mode.
Mode
Door
Green
2)
•
3)
5)
Mode
Door
Red
Enter 000 for user slot.
•
4)
Press 8 to enter Menu 8.
The Mode indicator will turn red.
•
The Door indicator will flash orange.
The controller is now waiting for the
primary code of the user to be
deleted.
Enter the primary code to be deleted.
The Mode indicator will flash red.
Orange
0
Mode
0
0
Door
Red
Orange
Red
Orange
Mode
Door
Enter your programming code to confirm the deletion.
If the programming code is valid, three beeps will be heard
and the controller will return to its normal mode.
If the programming code is invalid, a long beep will be heard
and the controller will return to its normal mode.
AC-Q4x Family, Installation and user Manual
Page 48
Programming
4.14
RELAY CODES ASSIGNMENT
When a primary code is enrolled for any user, the user is
authorized to activate the Lock Strike relay. However, different
user codes may be set to operate the auxiliary relay instead or
operate both the Lock strike and auxiliary relay. Assignment of
such codes is achievable for any valid user code entered in the
controller.
There are two methods to assign relay codes to users: a standard
method and a search method.
4.14.1
1)
2)
•
•
3)
Depress 9 to enter Menu 9.
The Mode indicator will turn green.
The Door indicator will turn orange.
Mode
Door
Green
Mode
Door
Green
Enter the 3-digit user slot for code assignment.
•
4)
Relay Code Assignment using Standard Method
Enter the programming mode.
•
•
•
The Door indicator will flash green.
Orange
? ?
Mode
?
Door
Green Orange
Enter the assignment digit for the current user slot:
1 will activate the Lock Strike relay only deafult
2 will activate the Auxiliary relay only
3 will activate the Lock Strike and Auxiliary relays.
If the assignment code is valid, the Mode
indicator will stop flashing.
Mode
Door
Green
Orange
The controller is now waiting for another slot number. Depress the
# key to move to the next slot or enter a new slot number. If you
do not wish to continue, depress the # key twice and the
controller will return to its normal mode.
Page 49
AC-Q4x Family, Installation and user Manual
Programming
4.14.2
1)
2)
Relay Code Assignment using Search Method
Enter the programming mode.
Depress 9 to enter Menu 9.
• The Mode indicator will turn green.
• The Door indicator will turn orange.
3)
Mode
Door
Green
Mode
Door
Green
Enter 000 for user slot access.
•
The Door indicator will flash orange.
Orange
0
Mode
0
0
Door
Green Orange
The controller is now waiting for the primary code of the user.
4)
Enter the primary code belonging to
the user.
• The Mode indicator will flash green.
5)
•
•
•
Mode
Door
Green Orange
Enter the assignment digit for the current user slot:
1 will activate the Lock Strike relay only deafult
2 will activate the Auxiliary relay only
3 will activate the Lock Strike and Auxiliary relays.
If the assignment digit is valid, three beeps will be heard and the
controller will return to its normal mode.
If the assignment digit is invalid, a long beep will sound and the
controller will wait for another assignment digit to be entered.
AC-Q4x Family, Installation and user Manual
Page 50
Programming
4.15
PIN CODE LENGTH / FACTORY DEFAULT
SETTINGS
Warning:
You must be very careful before using this command!
Changing the pin code length will also erase the entire
memory contents, including all user and special codes, and
return all codes to their factory-default settings
1)
Enter the programming mode.
Mode
Door
Green
2)
Select the desired pin code length as
followes:
a. 00 – Returns to factury defaults and sets a 4 digit code.
b. 05 - Returns to factury defaults and sets a 5 digit code.
c. 06 - Returns to factury defaults and sets a 6 digit code.
d. 08 - Returns to factury defaults and sets a 4-8 digit code.
Note:
When choosing the 4-8 option, please note that you should
either enter zeros before the code, or press pound at the end
(for example if your code is 12345, enter either 00012345 or
12345#).
•
3)
Both the Mode and Door indicators
will flash red.
Mode
Door
Red
Red
Enter your programming code.
If the programming code is valid, all memory will be erased, you
will hear three beeps and the controller will return to normal mode
If the programming code is invalid you will hear a long beep and
the controller will return to normal mode, without erasing the
memory contents.
Page 51
AC-Q4x Family, Installation and user Manual
Programming
4.16
REPLACING A PROGRAMMING CODE
Note:
The controller must be in its normal mode for the procedure
to work. Insure that the Mode indicator is green before
proceeding.
1)
2)
3)
4)
5)
4.17
Remove power from the controller.
Depress and hold the REX pushbutton.
Apply power to the unit with the REX pushbutton depressed.
Release the REX pushbutton.
You now have 15 seconds to program a new programming
code into the unit using the initial default code, before the
controller reverts to the existing code.
the deafult code depends on the pin length selected, reffer
to the programming Menu table on page 27.
REPLACING A NORMAL/SECURE CODE
Note:
The controller must be in its secure mode for the procedure
to work. Insure that the Mode indicator is red before
proceeding.
1)
2)
3)
4)
5)
Remove power from the controller.
Depress and hold the REX pushbutton.
Apply power to the unit with the REX pushbutton depressed.
Release the REX pushbutton.
You now have 15 seconds to use the normal/secure code to
return to the normal mode. Once in the normal mode, enter
the programming mode to program a new normal/secure
code. the deafult code depends on the pin length selected,
reffer to the programming Menu table on page 27.
AC-Q4x Family, Installation and user Manual
Page 52
Limited Warranty
Appendix A. Limited Warranty
ROSSLARE ENTERPRISES LIMITED (Rosslare) TWO and/or FIVE YEAR LIMITED
WARRANTY is applicable worldwide. This warranty supersedes any other warranty.
Rosslare's TWO and/or FIVE YEAR LIMITED WARRANTY is subject to the following
conditions:
Warranty
Warranty of Rosslare's products extends to the original purchaser (Customer) of the
Rosslare product and is not transferable.
Products Covered By This Warranty and Duration
ROSSLARE ENTERPRISES LTD. AND / OR SUBSIDIARIES (ROSSLARE) warrants that
the AC-Qx, metal stand alone controller family as listed above, to be free from defects in
materials and assembly in the course of normal use and service. The warranty period
commences with the date of shipment to the original purchaser and extends for a period of
2 years (24 Months) for models AC-Q41H, AC-Q41HB, AC-Q42H and AC-Q42HB and 5
years (60 months) for models AC-Q41SB, AC-Q42SB and AC-Q44.
Warranty Remedy Coverage
In the event of a breach of warranty, ROSSLARE will credit Customer with the price of the
Product paid by Customer, provided that the warranty claim is delivered to ROSSLARE by
the Customer during the warranty period in accordance with the terms of this warranty.
Unless otherwise requested by ROSSLARE ENTERPRISES LTD. AND / OR
SUBSIDIARIES representative, return of the failed product(s) is not immediately required.
If ROSSLARE has not contacted the Customer within a sixty (60) day holding period
following the delivery of the warranty claim, Customer will not be required to return the
failed product(s). All returned Product(s), as may be requested at ROSSLARE
ENTERPRISES LTD. AND /OR SUBSIDIARY’S sole discretion, shall become the property
of ROSSLARE ENTERPRISES LTD. AND /OR SUBSIDIARIES.
To exercise the warranty, the user must contact Rosslare Enterprises Ltd. to obtain an
RMA number after which, the product must be returned to the Manufacturer freight prepaid
and insured
In the event ROSSLARE chooses to perform a product evaluation within the sixty (60) day
holding period and no defect is found, a minimum US$ 50.00 or equivalent charge will be
applied to each Product for labor required in the evaluation.
Rosslare will repair or replace, at its discretion, any product that under normal conditions
of use and service proves to be defective in material or workmanship. No charge will be
applied for labor or parts with respect to defects covered by this warranty, provided that
the work is done by Rosslare or a Rosslare authorized service center.
Page 53
AC-Q4x Family, Installation and user Manual
Limited Warranty
Exclusions and Limitations
ROSSLARE shall not be responsible or liable for any damage or loss resulting from the
operation or performance of any Product or any systems in which a Product is
incorporated. This warranty shall not extend to any ancillary equipment not furnished by
ROSSLARE, which is attached to or used in conjunction with a Product, nor to any Product
that is used with any ancillary equipment, which is not furnished by ROSSLARE.
This warranty does not cover expenses incurred in the transportation, freight cost to the
repair center, removal or reinstallation of the product, whether or not proven defective.
Specifically excluded from this warranty are any failures resulting from Customer's
improper testing, operation, installation, or damage resulting from use of the Product in
other than its normal and customary manner, or any maintenance, modification, alteration,
or adjustment or any type of abuse, neglect, accident, misuse, improper operation, normal
wear, defects or damage due to lightning or other electrical discharge. This warranty does
not cover repair or replacement where normal use has exhausted the life of a part or
instrument, or any modification or abuse of, or tampering with, the Product if Product
disassembled or repaired in such a manner as to adversely affect performance or prevent
adequate inspection and testing to verify any warranty claim.
ROSSLARE does not warrant the installation, maintenance, or service of the Product.
Service life of the product is dependent upon the care it receives and the conditions under
which it has to operate.
In no event shall Rosslare be liable for incidental or consequential damages.
Limited Warranty Terms
THIS WARRANTY SETS FORTH THE FULL EXTENT OF ROSSLARE ENTERPRISES LTD. AND
IT’S SUBSIDIARIES’ WARRANTY
THE TERMS OF THIS WARRANTY MAY NOT BE VARIED BY ANY PERSON, WHETHER OR
NOT PURPORTING TO REPRESENT OR ACT ON BEHALF OF ROSSLARE.
THIS LIMITED WARRANTY IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES. ALL OTHER
WARRANTIES EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
SPECIFICALLY EXCLUDED.
IN NO EVENT SHALL ROSSLARE BE LIABLE FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT, OR FOR ANY OTHER INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF
USE, LOSS OF TIME, COMMERCIAL LOSS, INCONVENIENCE, AND LOSS OF PROFITS,
ARISING OUT OF THE INSTALLATION, USE, OR INABILITY TO USE SUCH PRODUCT, TO
THE FULLEST EXTENT THAT ANY SUCH LOSS OR DAMAGE MAY BE DISCLAIMED BY LAW .
THIS WARRANTY SHALL BECOME NULL AND VOID IN THE EVENT OF A VIOLATION OF THE
PROVISIONS OF THIS LIMITED WARRANTY.
AC-Q4x Family, Installation and user Manual
Page 54
Technical Support
Appendix B. Technical Support
Asia Pacific, Middle East, Africa
Rosslare Security Products Headquarters
905-912 Wing Fat Industrial Bldg,
12 Wang Tai Road,
Kowloon Bay Hong Kong
Tel:
+852 2795-5630
Fax:
+852 2795-1508
E-mail: support.apac@rosslaresecurity.com
United States and Canada
1600 Hart Court, Suite 103
Southlake, TX, USA 76092
Toll Free:+1-866-632-1101
Local:+1-817-305-0006
Fax:
+1-817-305-0069
E-mail: support.na@rosslaresecurity.com
Europe
Global Technical Support & Training Center
HaMelecha 22
Rosh HaAyin, Israel 48091
Tel:
+972 3 938-6838
Fax:
+972 3 938-6830
E-mail: support.eu@rosslaresecurity.com
South America
Pringles 868, 1640 Martinez
Buenos Aires
Argentina
Tel:
+54 11 4798-0095
Fax:
+54 11 4798-2228
E-mail: support.la@rosslaresecurity.com
Web Site: www.rosslaresecurity.com
Page 55
AC-Q4x Family, Installation and user Manual
0706-0960121+02
www.rosslaresecurity.com