MC65
MOBILE COMPUTER
INTEGRATOR GUIDE
MC65 MOBILE COMPUTER
INTEGRATOR GUIDE
72E-142435-02
Rev. B
June 2012
ii
MC65 Integrator Guide
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means,
without permission in writing from Motorola. This includes electronic or mechanical means, such as
photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to
change without notice.
The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on
a licensed basis. Motorola grants to the user a non-transferable and non-exclusive license to use each
software or firmware program delivered hereunder (licensed program). Except as noted below, such license
may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of
Motorola. No right to copy a licensed program in whole or in part is granted, except as permitted under
copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with
other program material, create a derivative work from a licensed program, or use a licensed program in a
network without written permission from Motorola. The user agrees to maintain Motorola’s copyright notice on
the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in
whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed
program delivered to the user or any portion thereof.
Motorola reserves the right to make changes to any software or product to improve reliability, function, or
design.
Motorola does not assume any product liability arising out of, or in connection with, the application or use of
any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any Motorola, Inc.,
intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in
Motorola products.
iii
Revision History
Changes to the original guide are listed below:
Change
Date
Description
-01 Rev A
9/2010
Initial release.
-01 Rev. B
3/2011
Correct scan button wake up on page 1-9.
-02 Rev. A
11/2011
Updates due to latest software, OEM version 02.31.00XX.
-02 Rev. B
06/30/12
Add Power off procedure, add new registry settings.
iv
MC65 Integrator Guide
TABLE OF CONTENTS
Revision History .............................................................................................................................. iii
About This Guide
Introduction .....................................................................................................................................
Documentation Set .........................................................................................................................
Configurations.................................................................................................................................
Software Versions .....................................................................................................................
Chapter Descriptions ......................................................................................................................
Notational Conventions...................................................................................................................
Related Documents ........................................................................................................................
Service Information .........................................................................................................................
xi
xi
xi
xii
xii
xiii
xiii
xiv
Chapter 1: Getting Started
Introduction ....................................................................................................................................
Unpacking ......................................................................................................................................
Getting Started ...............................................................................................................................
Installing a microSD Card ........................................................................................................
Installing the SIM Card .............................................................................................................
Installing the Battery ................................................................................................................
Charging the Battery ................................................................................................................
Charging the Main Battery .................................................................................................
Charging Spare Batteries ...................................................................................................
Charging Temperature .......................................................................................................
Powering On the MC65 ............................................................................................................
Calibrating the Screen ........................................................................................................
Powering Off the MC65 ............................................................................................................
First-time Network Activation ...................................................................................................
Network Activation .............................................................................................................
Replacing the Battery .....................................................................................................................
Resetting the MC65 .......................................................................................................................
Performing a Clean Boot ................................................................................................................
Waking the MC65 ..........................................................................................................................
1-1
1-1
1-2
1-2
1-3
1-4
1-5
1-5
1-6
1-6
1-6
1-6
1-7
1-7
1-7
1-8
1-8
1-9
1-9
vi
MC65 Integrator Guide
Chapter 2: Accessories
Introduction ....................................................................................................................................
Single Slot USB Cradle ..................................................................................................................
Setup ........................................................................................................................................
Charging the MC65 Battery .....................................................................................................
Charging the Spare Battery .....................................................................................................
Battery Charging Indicators .....................................................................................................
Charging Temperature .......................................................................................................
Single Slot Ethernet/Modem/USB Cradle ......................................................................................
Required Software ...................................................................................................................
Country Settings ......................................................................................................................
Setup ........................................................................................................................................
Indicators .................................................................................................................................
MC65 Software Setup ..............................................................................................................
Ethernet Setup ...................................................................................................................
Modem Setup .....................................................................................................................
Four Slot Ethernet Cradle ..............................................................................................................
Setup ........................................................................................................................................
Daisychaining Ethernet Cradles ...............................................................................................
Ethernet Cradle Drivers ...........................................................................................................
Charging and Communication .................................................................................................
LED Charging Indicators ....................................................................................................
Charge LED .......................................................................................................................
Speed LED .........................................................................................................................
Link LED ............................................................................................................................
Charging Temperature .......................................................................................................
LED Communication Indicators (CRD5500-4000ER) ........................................................
LED Communication Indicators (CRD5501-4000ER) ........................................................
Four Slot Charge Only Cradle .......................................................................................................
Setup ........................................................................................................................................
Charging Temperature .......................................................................................................
Wall Mount Bracket ........................................................................................................................
VCD5500 Vehicle Cradle ...............................................................................................................
Requirements ...........................................................................................................................
Connector Pin-Outs ...........................................................................................................
Mounting the Cradle .................................................................................................................
Power Connection ....................................................................................................................
Charging the MC65 Battery .....................................................................................................
Removing the MC65 ..........................................................................................................
Battery Charging Indicators .....................................................................................................
Charging Temperature .......................................................................................................
Four Slot Battery Charger ..............................................................................................................
Spare Battery Charging ...........................................................................................................
Battery Charging Indicators .....................................................................................................
Charging Temperature .......................................................................................................
Cables ............................................................................................................................................
USB Charging Cable ................................................................................................................
Charge Only Cable ..................................................................................................................
Auto Charge Cable ..................................................................................................................
Connecting to the MC65 ..........................................................................................................
Battery Charging Indicators .....................................................................................................
2-1
2-3
2-3
2-3
2-4
2-4
2-5
2-6
2-6
2-6
2-7
2-7
2-8
2-8
2-8
2-10
2-10
2-11
2-11
2-13
2-13
2-13
2-13
2-13
2-14
2-14
2-14
2-15
2-15
2-15
2-16
2-18
2-18
2-18
2-18
2-19
2-21
2-21
2-22
2-22
2-23
2-23
2-23
2-23
2-25
2-25
2-25
2-26
2-26
2-27
Table of Contents
Charging Temperature .............................................................................................................
Vehicle Holder ................................................................................................................................
Installation Reminders .............................................................................................................
Device Mounting Precautions ..................................................................................................
Installation ................................................................................................................................
Assembly ............................................................................................................................
Windshield Installation .......................................................................................................
Flat Surface Installation ......................................................................................................
2-27
2-28
2-28
2-28
2-28
2-29
2-29
2-30
Chapter 3: ActiveSync
Introduction ....................................................................................................................................
Installing ActiveSync ......................................................................................................................
MC65 Setup ...................................................................................................................................
Setting Up an ActiveSync Connection on the Host Computer .......................................................
Synchronization the MC65 .......................................................................................................
3-1
3-1
3-2
3-3
3-3
Chapter 4: Application Deployment
Introduction ....................................................................................................................................
Security ..........................................................................................................................................
Application Security .................................................................................................................
Digital Signatures .....................................................................................................................
Locking Down a Mobile Computer .....................................................................................
Installing Certificates ..........................................................................................................
Device Management Security ..................................................................................................
Remote API Security ................................................................................................................
Packaging ......................................................................................................................................
Deployment ....................................................................................................................................
Installation Using ActiveSync ...................................................................................................
Installation Using Storage Card ...............................................................................................
Installation Using AirBEAM ......................................................................................................
MSP .........................................................................................................................................
Update Loader Image ..............................................................................................................
Download Update Loader Package ...................................................................................
ActiveSync .........................................................................................................................
microSD Card .....................................................................................................................
XML Provisioning ...........................................................................................................................
Creating an XML Provisioning File ...........................................................................................
XML Provisioning vs. RegMerge and Copy File .......................................................................
RegMerge ..........................................................................................................................
CopyFiles ...........................................................................................................................
Storage ..........................................................................................................................................
Random Access Memory .........................................................................................................
Volatile File Storage (Cache Disk) .....................................................................................
Persistent Storage ...................................................................................................................
Application Folder ....................................................................................................................
Enterprise Mobility Developer Kits .................................................................................................
4-1
4-1
4-1
4-1
4-2
4-3
4-3
4-3
4-4
4-4
4-4
4-4
4-5
4-5
4-5
4-5
4-5
4-6
4-6
4-6
4-7
4-7
4-7
4-8
4-8
4-8
4-9
4-9
4-9
vii
viii
MC65 Integrator Guide
Chapter 5: Phone Setup
Introduction ....................................................................................................................................
Automatic Network Setup ........................................................................................................
Manual Network Setup .............................................................................................................
CDMA Network Setup ........................................................................................................
GSM Network Setup ..........................................................................................................
Dual Network Usage ......................................................................................................................
Switching Between CDMA Networks .............................................................................................
Global Usage .................................................................................................................................
Configuring a GSM Data Connection ............................................................................................
Phone Settings ..............................................................................................................................
Sounds .....................................................................................................................................
Security ....................................................................................................................................
Enabling a PIN ...................................................................................................................
Changing a PIN ..................................................................................................................
Disabling a PIN ..................................................................................................................
GSM Services ..........................................................................................................................
Call Barring (Call Blocking) ................................................................................................
Caller ID .............................................................................................................................
Call Forwarding ..................................................................................................................
Call Waiting ........................................................................................................................
Voice Mail and Text Messages ..........................................................................................
Fixed Dialing ......................................................................................................................
Internet .....................................................................................................................................
Services ...................................................................................................................................
Broadcast Channels ...........................................................................................................
GPS Privacy .......................................................................................................................
HAC .........................................................................................................................................
5-1
5-1
5-1
5-1
5-2
5-3
5-3
5-3
5-5
5-6
5-6
5-6
5-6
5-7
5-8
5-8
5-8
5-8
5-8
5-9
5-9
5-9
5-10
5-10
5-10
5-10
5-10
Chapter 6: Maintenance & Troubleshooting
Introduction ....................................................................................................................................
Maintaining the MC65 ....................................................................................................................
Removing the Screen Protector .....................................................................................................
Battery Safety Guidelines ..............................................................................................................
Cleaning .........................................................................................................................................
Materials Required ...................................................................................................................
Cleaning the MC65 ..................................................................................................................
Housing ..............................................................................................................................
Display ...............................................................................................................................
Scanner Exit Window .........................................................................................................
Connector ..........................................................................................................................
Cleaning Cradle Connectors ....................................................................................................
Cleaning Frequency .................................................................................................................
Troubleshooting .............................................................................................................................
MC65 .......................................................................................................................................
Bluetooth Connection ...............................................................................................................
Single Slot USB Cradle ............................................................................................................
Four Slot Ethernet Cradle ........................................................................................................
Vehicle Cradle ..........................................................................................................................
Four Slot Battery Charger ........................................................................................................
6-1
6-1
6-2
6-2
6-3
6-3
6-4
6-4
6-4
6-4
6-4
6-4
6-5
6-5
6-5
6-7
6-7
6-8
6-9
6-9
Table of Contents
Cables ...................................................................................................................................... 6-10
Magnetic Stripe Reader ........................................................................................................... 6-10
Appendix A: Technical Specifications
MC65 Technical Specifications ......................................................................................................
MC65 .......................................................................................................................................
Decode Zones ..........................................................................................................................
SE4500-SR ........................................................................................................................
SE4500-DL .........................................................................................................................
MC65 External Connector Pin-Outs .........................................................................................
MC65 Accessory Specifications .....................................................................................................
Single Slot USB Cradle ............................................................................................................
Four Slot Battery Charger ........................................................................................................
Four Slot Charge Only Cradle ..................................................................................................
Four Slot Ethernet Cradle ........................................................................................................
Magstripe Reader ....................................................................................................................
Vehicle Cradle ..........................................................................................................................
Cables ......................................................................................................................................
A-1
A-1
A-6
A-6
A-8
A-10
A-11
A-11
A-11
A-12
A-12
A-13
A-14
A-14
Appendix B: Software
SMS8 Configuration .......................................................................................................................
Cache Disk Configuration ..............................................................................................................
Auto Reboot ...................................................................................................................................
Daily Reboot ..................................................................................................................................
SMS Cell Broadcast .......................................................................................................................
B-1
B-1
B-2
B-2
B-2
Glossary
Index
ix
x
MC65 Integrator Guide
ABOUT THIS GUIDE
Introduction
This Integrator Guide provides information about setting up and configuring the MC65 and it’s accessories.
NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.
Documentation Set
The documentation for the MC65 is divided into guides that provide information for specific user needs.
• MC65 Quick Start Guide - describes how to get the MC65 up and running.
• MC65 User Guide - describes how to use the MC65.
• MC65 Integrator Guide - describes how to set up the MC65 and it's accessories.
• Enterprise Mobility Developer Kit (EMDK) Help File - provides API information for writing applications.
Configurations
This guide covers the following configurations:
Configuration
MC659B
Radios
WLAN: 802.11 a/b/g
WPAN: Bluetooth
v2.0 EDR
WWAN: CDMA or
GSM/UMTS
GPS: Stand-alone
GPS or
A-GPS
Display
3.5” VGA
Color
Memory
256 MB RAM/
1 GB Flash or
512 MB
RAM/1 GB
Flash
Data Capture
Options
2D imager or 2D
imager and
camera
Operating
System
Windows
Mobile 6.5
Professional
Keypads
Numeric,
QWERTY,
QWERTZ,
AZERTY, PIM
or DSD
xii
MC65 Integrator Guide
Software Versions
This guide covers various software configurations and references are made to operating system or software
versions for:
• Adaptation Kit Update (AKU) version
• OEM version
• Fusion version
• Phone version.
AKU Version
To determine the Adaptation Kit Update (AKU) version:
Tap Start > Settings > System > About > Version.
The second line lists the operating system version and the build number. The last part of the build number
represents the AKU number. For example, Build 23103.5.3.3 indicates that the device is running AKU version
5.3.3.
OEM Version
To determine the OEM software version:
Tap Start > Settings > System > System Info > System.
Fusion Software
To determine the Fusion software version:
Tap Status Bar >
> Wireless Status > Versions.
Phone Software
To determine the Phone software version:
Press
>
> Phone information.
Chapter Descriptions
Topics covered in this guide are as follows:
• Chapter 1, Getting Started provides information on MC65 configurations and accessories, charging the
battery, and resetting the device.
• Chapter 2, Accessories describes the accessories available for the MC65 and how to set up power
connections and battery charging capabilities, where applicable.
• Chapter 3, ActiveSync provides instructions on installing ActiveSync and setting up a partnership
between the MC65 and a host computer.
• Chapter 4, Application Deployment provides information for provisioning and deploying applications to
the MC65.
• Chapter 5, Phone Setup explains how to setup the phone on GCSM/UMTS and CDMA networks.
About This Guide
xiii
• Chapter 6, Maintenance & Troubleshooting includes instructions on cleaning and storing the MC65, and
provides troubleshooting solutions for potential problems during MC65 operation.
• Appendix A, Technical Specifications includes tables listing the technical specifications for the MC65 and
its accessories.
Notational Conventions
The following conventions are used in this document:
• “EDA” refers to Motorola MC65 family of hand-held computers.
• Italics are used to highlight the following:
• chapters and sections in this and related documents
• dialog box, window, and screen names
• drop-down list and list box names
• check box and radio button names
• icons on a screen.
• Bold text is used to highlight the following:
• key names on a keypad
• button names on a screen.
• Bullets (•) indicate:
• action items
• lists of alternatives
• lists of required steps that are not necessarily sequential.
• Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
Related Documents
• MC65 Quick Start Guide, p/n 72-114971-xx.
• MC65 Windows Mobile 6 Regulatory Guide, p/n 72-134232-xx.
• MC65 User Guide, p/n 72E-133769-xx.
• Mobility Services Platform 3.2 User Guide, p/n 72E-100158-xx.
• AirBEAM Smart Windows CE Client Product Reference Guide, p/n 72-63060-01.
• Wireless Fusion Enterprise Mobility Suite User Guide for Version 3.20, p/n 72E-113153-01.
• Enterprise Mobility Developer Kits (EMDKs), available at: http://supportcentral.motorola.com.
• Latest ActiveSync software, available at: http://www.microsoft.com.
For the latest version of this guide and all guides, go to: http://supportcentral.motorola.com.
xiv
MC65 Integrator Guide
Service Information
If you have a problem with your equipment, contact Motorola Solutions Global Customer Support for your
region. Contact information is available at: http://www.motorolasolutions.com/contactsupport.
When contacting Enterprise Solutions support, please have the following information available:
• Serial number of the unit (found on manufacturing label)
• Model number or product name (found on manufacturing label)
• Software type and version number.
Manufacturing label
Motorola responds to calls by e-mail, telephone or fax within the time limits set forth in support agreements.
If your problem cannot be solved by Motorola Solutions Global Customer Support, you may need to return your
equipment for servicing and will be given specific directions. Motorola is not responsible for any damages
incurred during shipment if the approved shipping container is not used. Shipping the units improperly can
possibly void the warranty.
If you purchased your Enterprise Solutions business product from a Motorola business partner, contact that
business partner for support.
CHAPTER 1 GETTING STARTED
Introduction
This chapter lists the parts and accessories for the MC65 and explains how to set up the MC65 for the first
time.
Unpacking
Carefully remove all protective material from the MC65 and save the shipping container for later storage and
shipping.
Verify that you received the following:
• MC65 EDA
• 3600 mAh Lithium-ion battery
• stylus with tether (installed)
• screen protector, installed on display window
• Regulatory Guide
• Quick Start Guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Motorola Solutions
Global Customer Support center immediately. SeeService Information on page xiv for contact information.
Prior to using the MC65 for the first time, remove the protective shipping film that covers the scan window,
display and camera window.
1-2
MC65 Integrator Guide
Getting Started
To start using the MC65 for the first time:
• Install a microSD card (optional)
• Install the SIM card (GSM only)
• Install the main battery pack.
• Charge the MC65.
• Power on the MC65.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack.
Refer to the documentation provided with the card for more information, and follow the manufacturer’s
recommendations for use.
CAUTION
Follow proper ESD precautions to avoid damaging the SD card. Proper ESD precautions include, but
are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
To install the microSD card:
1.
Remove the handstrap.
2.
Lift rubber access door.
3.
Slide the SIM card holder door up to unlock.
4.
Lift SIM card holder door.
Rubber access door
SIM card holder door
microSD card holder door
Figure 1-1 Lift SIM Slot Holder Door
5.
Lift microSD card holder door.
6.
Insert the microSD card into card holder door ensuring that the card slides into the holding tabs on each
side of the door.
Getting Started
1-3
microSD card
Holding tab
Figure 1-2 Insert microSD Card in Holder
7.
Close the card holder door and push down until it is securely into place.
8.
If installing a SIM card, proceed to Installing the SIM Card.
9.
Close SIM card holder door and slide down until it locks into place.
10. Close rubber access door.
Installing the SIM Card
NOTE
GSM only.
The MC65 does not support copying multiple contacts to some SIM cards. If an error message appears,
see Chapter 6, Maintenance & Troubleshooting for more information.
GSM phone service requires a Subscriber Identification Module (SIM) card. Obtain the card from the your
service provider. The card fits into the MC65 and can contain the following information:
• Mobile phone service provider account details.
• Information regarding service access and preferences.
• Contact information, which can be moved to Contacts on the MC65.
• Any additional services to which you have subscribed.
NOTE For more information about SIM cards, refer to the service provider's documentation.
To install the SIM card:
1.
Lift rubber access door.
2.
Slide the SIM card holder up to unlock.
3.
Lift the SIM card holder door.
1-4
MC65 Integrator Guide
Figure 1-3 Lifting the SIM Cover
4.
Insert the SIM card, as shown in Figure 1-4 ensuring that the card slides into the holding tabs on each side
of the door.
Figure 1-4 Inserting the SIM Card
5.
Close SIM card holder door and slide down to lock into place.
6.
Close the rubber access door.
7.
Install the battery.
NOTE For detailed information about WWAN activation and settings, refer to the MC65 Integrator Guide.
Installing the Battery
To install the battery.
1.
Insert the battery, bottom first, into the battery compartment in the back of the MC65.
2.
Press the battery down into the battery compartment until the battery release latch snaps into place.
3.
Replace the handstrap.
Getting Started
1-5
Battery Release Latch
2
1
Battery
Figure 1-5 Inserting the Battery
Charging the Battery
CAUTION
Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page
6-2.
Charging the Main Battery
Before using the MC65 for the first time, charge the main battery until the amber Charging/Battery Status LED
remains lit (see Table 1-1 on page 1-6 for charge status indications). To charge the MC65, use a cable or a
cradle with the appropriate power supply. For information about the accessories available for the MC65, see
Chapter 2, Accessories.
The MC65 is equipped with a memory backup battery which automatically charges from the fully-charged main
battery. When using the MC65 for the first time, the backup battery requires approximately 40 hours to fully
charge. This is also true any time the backup battery is discharged, which occurs when the main battery is
removed for several hours. The backup battery retains RAM data in memory for at least 15 minutes (at room
temperature) when the MC65’s main battery is removed. When the MC65 reaches a very low battery state, the
combination of main battery and backup battery retains RAM data in memory for at least 36 hours.
For cable and cradle setup and charging procedures refer to the MC65 Integrator Guide.
• USB Charging Cable
• Charge Only Cable
• Single Slot USB Cradle
• Four Slot Charge Only Cradle
• Four Slot Ethernet Cradle.
To charge the main battery:
1.
Connect the charging accessory to the appropriate power source.
1-6
MC65 Integrator Guide
2.
Insert the MC65 into a cradle or attach to a cable. The MC65 begins charging. The Charging/Battery Status
LED blinks amber while charging, then turns solid amber when fully charged. See Table 1-1 for charging
indications.
The 3600 mAh battery charges in less than six hours.
Table 1-1 LED Charge Indicators
Charging/Battery
Status LED
Indication
Off
MC65 is not charging.
MC65 is not inserted correctly in the cradle or connected to a power source.
Charger/cradle is not powered.
Slow Blinking Amber
(1 blink every 2 seconds)
MC65 is charging.
Solid Amber
Charging complete.
Note: When the battery is initially inserted in the MC65, the amber LED flashes once if
the battery power is low or the battery is not fully inserted.
Fast Blinking Amber
(2 blinks/second)
Charging error, e.g.:
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
Charging Spare Batteries
See Chapter 2, Accessories for information on using accessories to change spare batteries.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Note that charging is intelligently
controlled by the MC65.
To accomplish this, for small periods of time, the MC65 or accessory alternately enables and disables battery
charging to keep the battery at acceptable temperatures. The MC65 or accessory indicates when charging is
disabled due to abnormal temperatures via its LED. See Table 1-1.
Powering On the MC65
Press the Power button to turn on the MC65. The splash screen displays for about a minute as the MC65
initializes its flash file system, then the calibration window appears.
Calibrating the Screen
NOTE The Calibration screen can be accessed by pressing Blue key then Backspace key.
To calibrate the screen so the cursor on the touch screen aligns with the tip of the stylus:
1.
Remove the stylus from its holder on the side of the MC65.
2.
Carefully press and briefly hold the tip of stylus on the center of each target that appears on the screen.
3.
Repeat as the target moves around the screen, then tap the screen to continue.
Getting Started
1-7
Powering Off the MC65
NOTE Only available on OEM version 02.31.002 and above.
To power off the MC65, press the Power button for five seconds. Tap Power Off.
Figure 1-6 Power Key Menu
First-time Network Activation
Network Activation
To activate on a GSM/UMTS network:
1.
If an active SIM card was installed in the MC65, the MC65 performs the activation process.
2.
The Phone Network - GSM/UMTS Setup dialog box displays.
3.
Tap Yes and then OK. For some carriers, the MC65 resets.
4.
If during start-up, no update connection settings message appears, tap Start > Settings > Connection >
Phone Network Setup and tap Update Connection Settings button.
5.
If the network is unsupported, a message appears with links for manually setting the data connection and
MMS settings.
To activate on a CDMA network:
1.
Create an account with the CDMA carrier. Provide the MEID number (located on the back of the MC65 or
tap Start > Settings > System Display Info) to the customer service representative.
2.
If a SIM card was not installed, a No SIM card found dialog box displays.
3.
Tap OK. The Phone Network - CDMA Activation dialog box displays.
4.
Tap Yes to activate on a CDMA network.
5.
On the CDMA Setup tab, tap the Preferred network option and select a network.
6.
Tap Yes.
7.
Tap the Start Activation button.
8.
Tap Yes to activate.
1-8
MC65 Integrator Guide
9.
Press Activate Now button.
For detailed information for configuring the phone and activating on a different network, see Chapter 5, Phone
Setup.
Replacing the Battery
CAUTION
The MC65 backup battery retains data for up to 15 minutes. Replace the battery within 15 minutes to
ensure that application states are maintained and that data is not lost.
1.
If the MC65 is in suspend mode, press the red Power button to wake the device.
2.
Press and hold the red Power button for approximately 5 seconds.
3.
Release the Power button. On OEM version 02.31.00XX and above, tap Battery Swap. The Data Capture
LED lights red.
4.
When the LED turns off, remove the handstrap.
5.
Slide the battery latch to the right. The battery ejects slightly.
Battery Latch
1
2
Figure 1-7 Removing the Battery
6.
Lift the battery from the MC65.
7.
Insert the replacement battery, bottom first, into the battery compartment in the back of the MC65.
8.
Press the battery down until the battery release latch snaps into place.
9.
Replace the handstrap.
Resetting the MC65
A reset restarts the MC65 by closing all running programs. Data saved in flash memory or a memory card is
not lost.
If the MC65 is not functioning properly, perform a reset.
To perform a reset:
Getting Started
• On a numeric keypad, simultaneously press the red Power button and the
and
• On an alphanumeric keypad, simultaneously press the red Power button and the
• On a PIM keypad, simultaneously press the red Power button and the
and
1-9
keys.
and
keys.
keys.
Performing a Clean Boot
CAUTION
A clean boot should only be performed by an authorized system administrator. You must connect the
MC65 to AC power during a clean boot.
Removing AC power from the MC65 during a clean boot may render the MC65 inoperable.
A clean boot resets the MC65 to the factory default settings. All data in the Application folder is retained. You
must download the Clean Boot Package file from the Support Central web site,
http://supportcentral.motorola.com and install on the MC65.
To perform a clean boot:
1.
Download the Clean Boot Package from the Support Central web site. Follow the instructions included in
the package for installing the package onto the MC65.
2.
Perform a reset.
3.
Immediately, as soon as the device starts to boot and before the splash screen is visible, press and hold
the left scan button.
4.
Insert the MC65 into a powered cradle.
5.
The MC65 updates and then resets.
6.
Calibrate the screen.
Waking the MC65
The wake-up conditions define what actions wake up the MC65 after it has gone into suspend mode. The
MC65 can go into suspend mode by either pressing the Power button or automatically by time-out settings
Table 1-2 Wake-up Default Settings
Condition for Wake-up
Power Button
Automatic Time-out
AC power is applied.
No
Yes
MC65 is inserted into a cradle.
Yes
Yes
MC65 is removed from a cradle.
Yes
Yes
MC65 is connected to a USB device.
No
Yes
MC65 is disconnected from a USB device.
No
Yes
A key is pressed.
No
No
The left scan trigger is pressed.
Yes
Yes
1 - 10 MC65 Integrator Guide
Table 1-2 Wake-up Default Settings
Condition for Wake-up
Power Button
Automatic Time-out
The screen is touched.
No
No
Bluetooth communication
Yes
Yes
Incoming phone call
Yes
Yes
CHAPTER 2 ACCESSORIES
Introduction
This chapter provides set up information for the MC65 various accessories listed in Table 2-1:
Table 2-1 MC65 Accessories
Accessory
Part Number
Description
Cradles
Single Slot USB Cradle
CRD5500-1000UR
Charges the MC65 main battery and a spare battery.
Synchronizes the MC65 with a host computer through a USB
connection.
Single Slot
Ethernet/Modem/USB
Cradle
CRD5500-1000XR
Charges the MC65 main battery and a spare battery.
Synchronizes the MC65 with a host computer through an
Ethernet, Modem or USB connection. Refer to the Motorola
Support Central web site, http://supportcentral.motorola.com
from required software.
Four Slot Charge Only
Cradle
CRD5500-4000CR
CRD5501-4000CR
Charges up to four MC65 devices.
Four Slot Ethernet Cradle
CRD5500-4000ER
CRD5501-4000ER
Charges up to four MC65 devices and connects the MC65 with
an Ethernet network.
Vehicle Cradle
VCD5500-1001R
Installs in a vehicle and charges the MC65 main battery.
Vehicle Holder
VCH5500-1000R
Provides an alternative mounting solution for the MC65 in a
vehicle. Requires the Auto Charge cable for charging the MC65
battery.
Four Slot Spare Battery
Charger
SAC5500-4000CR
Charges up to four MC65 battery packs.
USB Charging Cable
25-108022-02R
Provides power to the MC65 and USB communication with a
host computer.
Charge Only Cable
25-112560-01R
Connects to a power supply to provide power to the MC65.
Auto Charge Cable
VCA5500-01R
Charges the MC65 using a vehicle’s cigarette lighter.
Chargers
2-2
MC65 Integrator Guide
Table 2-1 MC65 Accessories (Continued)
Accessory
Part Number
Description
Miscellaneous
Spare 3600 mAh lithium-ion
battery
BTRY-MC55EAB02
Replacement 3600 mAh battery.
DEX Cable
25-127558-01R
For use with electronic data exchange For example, vending
machines.
Trigger Handle
TRG5500-101R
Adds a gun-style handle with a scanning trigger for comfortable
and productive data capture.
Magnetic Stripe Reader
MSR5500-100R
Captures data from magnetic stripe cards.
Belt Mounted Rigid Holster
SG-MC5511110-01R
Clips onto belt to hold the MC65 when not in use.
Fabric Holster
SG-MC5521110-01R
Soft holder for added protection.
Stylus
KT-119150-03R
KT-119150-50R
Replacement stylus (3-pack).
Replacement stylus (50-pack).
Spring Loaded Stylus
STYLUS-00001-03R
STYLUS-00001-10R
Optional spring loaded stylus (3-pack).
Optional spring loaded stylus (10-pack).
Wall Mounting Kit
KT-136648-01R
Use for wall mounting the four slot cradles.
Screen Protector
KT-129195-03R
Package of 3 screen protectors.
Software
-
Enterprise Mobility Developer Kits (EMDKs), available at:
http://supportcentral.motorola.com.
Accessories
Single Slot USB Cradle
This section describes how to set up and use a Single Slot USB cradle with the MC65. For USB
communication setup procedures see Chapter 3, ActiveSync.
The Single Slot USB cradle:
• Provides 5.4 VDC power for operating the MC65.
• Synchronizes information between the MC65 and a host computer. See Chapter 3, ActiveSync for
information on setting up a partnership between the MC65 and a host computer.
• Charges the MC65’s battery.
• Charges a spare battery.
Setup
AC Line Cord
Power Supply
USB Port
Power Port
Figure 2-1 Single Slot USB Cradle Power and USB Connections
Charging the MC65 Battery
Connect the cradle to power. Insert the MC65 into the MC65 slot to begin charging.
2-3
2-4
MC65 Integrator Guide
Charge Status LED
Figure 2-2 MC65 Battery Charging
Charging the Spare Battery
Spare Battery
Spare Battery
Charging LED
Figure 2-3 Spare Battery Charging
Battery Charging Indicators
The Single Slot USB cradle charges the MC65’s main battery and a spare battery simultaneously.
Accessories
2-5
The MC65’s Charging/Battery Status LED indicates the status of the battery charging in the MC65. See Table
1-1 on page 1-6 for charging status indications.
The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle.
See Table 2-2 for charging status indications.
The 3600 mAh battery fully charges in approximately six hours.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the
MC65.
To accomplish this, for small periods of time, the MC65 or accessory alternately enables and disables battery
charging to keep the battery at acceptable temperatures. The MC65 or accessory indicates when charging is
disabled due to abnormal temperatures via its LED. See Table 1-1 on page 1-6 and Table 2-2.
Table 2-2
Spare Battery LED Charging Indicators
Spare Battery LED
(on cradle)
Indication
Slow Blinking Amber
Spare battery is charging.
Solid Amber
Spare battery is fully charged.
Fast Blinking Amber
Charging error.
Off
Not charging.
2-6
MC65 Integrator Guide
Single Slot Ethernet/Modem/USB Cradle
This section describes how to set up and use a Single Slot Ethernet/Modem/USB cradle with the MC65. For
USB communication setup procedures see Chapter 3, ActiveSync.
The Single Slot Ethernet/Modem/USB cradle:
• Provides 5.4 VDC power for operating the MC65.
• Connects the MC65 to a host computer using USB, a dial-up network using the modem or an Ethernet
network.
• Charges the MC65’s battery.
• Charges a spare battery.
Required Software
Download the USB Modem Driver and Update Loader Image Keyboard Micro Firmware for MC55xx package
from the Motorola Support Central web site: http://supportcentral.motorola.com.
First ensure that the MC65 has Keyboard Firmware version 4.2 or higher. To determine the Keyboard
Firmware version, tap Start > Settings > System > System Info icon > HW Version tab. If the Kbd FW Ver:
is 4.1 or lower, install the Keyboard Firmware 4.2 upgrade.
Install the Micro USB Modem Driver software. Following the instructions with the software package to install
the software.
Country Settings
The modem defaults to operation with US telephone networks. To operate the modem with other country
telephone networks, it must be configured using an application on the MC65. Download the Cradle Modem
Country Configurator Application Software for MC55xx package from the Motorola Support Central web site:
http://supportcentral.motorola.com.
Following the instructions with the software package to install the application on the MC65. The application
includes country selections for all supported countries and automatically programs the modem and adjust its
operating parameters to comply with the telephone network in the selected country.
Accessories
2-7
Setup
Ethernet Hub
AC Line Cord
Power Supply
USB Port
Phone Port
Ethernet Port
Power Port
Figure 2-4 Cradle Setup
Modem USB Ethernet
Figure 2-5 Connection Switch
Indicators
• Spare Battery Charging LED - Indicates the charging status of the spare battery.
• Ethernet/Modem LED - Blinks whenever Ethernet or modem connectivity is established.
• Speed LED - Lights green indicating that the transfer rate is 100 Mbps. When it is not lit, indicates that
the transfer rate is 10Mbps.
• Link LED - Blinks yellow to indicate activity, or stays lit to indicate that a link is established. When it is not
lit, indicates there is no link.
2-8
MC65 Integrator Guide
Spare Battery
Charging LED
Ethernet/Modem LED
Speed LED
Link LED
Figure 2-6 Cradle Indicators
MC65 Software Setup
Ethernet Setup
1.
Tap Start > Settings > Connections tab > Wi-Fi icon.
2.
Select Work from the drop-down menu.
3.
Select USB/Ethernet Series Adapter from the list box.
4.
Tap Ok.
5.
Tap Start > Settings > Connections tab > Connections icon.
6.
Tap Advanced tab.
7.
Tap Select Networks button.
8.
Select My Work Network from both drop-down menus.
9.
Tap Ok.
10. Tap the Tasks tab.
11. Select Edit my proxy server.
12. Enable both checkboxes.
13. Tap Advanced... button.
14. Tap HTTP type.
15. In the Server text box, enter the proxy server name.
16. In the Port text box, enter the port number.
17. In the User name text box, enter the user name for the proxy server.
18. In the Password text box, enter the password for the proxy server.
19. Tap ok three times.
20. Perform a warm boot.
Modem Setup
1.
Tap Start > Settings > Connections tab > Connections icon.
2.
Tap Add a new modem connection.
Accessories
3.
In the Enter a name for the connection text box, enter a name for the connection.
4.
In the Select a modem drop-down list, select Modem Cradle on USB.
5.
Tap Next.
6.
In the text box, enter the phone number to dial.
7.
Tap Next.
8.
In the User name text box, enter the user name, if required.
9.
In the Password text box, enter the password, if required.
10. Tap Finish.
11. To test the connection, tap Start > Programs > Internet Explorer. Enter a web address.
2-9
2 - 10 MC65 Integrator Guide
Four Slot Ethernet Cradle
This section describes how to set up and use a Four Slot Ethernet cradle with the MC65.
The Four Slot Ethernet cradle:
• Provides 5.4 VDC power for operating the MC65.
• Connects the MC65 (up to four) to an Ethernet network. The CRD5500-4000ER provides a maximum of
100 Mbps data rate. The CRD5501-4001ER provides a maximum of 1 Gbps data rate.
• Simultaneously charges up to four MC65s.
You cannot ActiveSync using the Four Slot Ethernet cradle. To ActiveSync with a host computer, use the Single
Slot USB/Serial cradle, USB Charging cable or Serial Charging cable.
Yellow Link LED (CRD4000-4000ER)
Green Right LED (CRD40001-4000ER)
Green Speed LED (CRD4000-4000ER)
Green Left LED (CRD40001-4000ER)
Figure 2-7 Four Slot Ethernet Cradle
Setup
Connect the Ethernet cradle to a power source and to an Ethernet switch, router, or hub, or a port on the host
device.
Accessories 2 - 11
Ethernet Port 1
Power Port
Ethernet Port
Ethernet Switch,
Router, or Hub
Connection
Figure 2-8 Four Slot Ethernet Cradle Connection
Daisychaining Ethernet Cradles
Daisychain up to four Ethernet cradles to connect several cradles to an Ethernet network. Use either a straight
or crossover cable. Daisy-chaining should not be attempted when the main Ethernet connection to the first
cradle is 10 Mbps as throughput issues will almost certainly result.
To daisychain more than one Ethernet cradle:
1.
Connect power to each Ethernet cradle to daisychain.
2.
Connect an Ethernet cable to Port 1 of the first cradle as shown in Figure 2-8.
3.
Connect a second Ethernet cable between Port 2 of the first cradle, and Port 1 of the second cradle.
4.
Connect additional cradles as described in Step 3.
Left LED
Right LED
Ethernet Port 2
Ethernet Port 1
Figure 2-9 Daisychaining Four Slot Ethernet Cradles
Ethernet Cradle Drivers
The MC65 includes Ethernet cradle drivers that initiate automatically when you place the MC65 in a properly
connected Four Slot Ethernet cradle. After inserting the MC65, configure the Ethernet connection:
2 - 12 MC65 Integrator Guide
1.
Tap Start > Settings > Connections tab >WiFi icon. The Configure Network Adapters window appears.
Figure 2-10 Configure Network Adapters Window
2.
In the My network card connects to: drop-down list, select the appropriate connection.
3.
In the Tap an adapter to modify settings: list, select USB/Ethernet Series Adapter.
Figure 2-11 IP Address Tab
4.
In the IP address window, select the appropriate radio button:
• Use server-assigned IP address
or
• Use specific IP address. Enter the IP address, Subnet mask, and Default gateway, as needed.
5.
Tap the Name Servers tab.
Accessories 2 - 13
Figure 2-12 Name Servers Tab
6.
Enter the appropriate DNS, Alt DNS, WINS, and Alt WINS server addresses.
7.
Tap ok.
Figure 2-13 Adapters Dialog Box
8.
Tap ok to confirm the setup.
9.
Tap ok to exit.
Charging and Communication
Insert the MC65 into a slot to begin charging.
LED Charging Indicators
The MC65’s charge LED shows the status of the battery charging in the MC65. See Table 1-1 on page 1-6 for
charging status indications.
The 3600 mAh battery fully charges in approximately six hours.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the
MC65.
To accomplish this, for small periods of time, the MC65 alternately enables and disables battery charging to
keep the battery at acceptable temperatures. The MC65 indicates when charging is disabled due to abnormal
temperatures via its LED. See Table 1-1 on page 1-6.
LED Communication Indicators (CRD5500-4000ER)
There are two LEDs on the front of the cradle and two on the Ethernet 2 port. The green Speed LED lights to
indicate that the transfer rate is 100 Mbps. When the LED is not lit the transfer rate is 10 Mbps. The yellow Link
LED blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates that
there is no link.
2 - 14 MC65 Integrator Guide
Table 2-3 CRD5500-4000ER LED Indicators
Data Rate
Green Speed LED (Left)
Yellow Link LED (right)
100 Mbps
On
On/Blink
10 Mbps
Off
On/Blink
LED Communication Indicators (CRD5501-4000ER)
There are two green LEDs on the front of the cradle and two green LED on the Ethernet 2 port. These green
LEDs light and blink to indicate the data transfer rate. When the LEDs are not lit the transfer rate is 10 Mbps.
Table 2-4 CRD5501-4000ER LED Indicators
Data Rate
Left LED (Green)
Right LED (Green)
1 Gbps
On/Blink
Off
100 Mbps
Off
On/Blink
10 Mbps
Off
Off
Accessories 2 - 15
Four Slot Charge Only Cradle
This section describes how to set up and use a Four Slot Charge Only cradle with the MC65.
The Four Slot Charge Only cradle:
• Provides 5.4 VDC power for operating the MC65.
• Simultaneously charges up to four MC65s.
You cannot ActiveSync using the Four Slot Charge Only cradle. To ActiveSync with a host computer, use the
Single Slot USB cradle.
Setup
Connect the Four Slot Charge Only cradle to a power source.
Figure 2-14 Four Slot Charge Only Cradle Connection
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the
MC65.
To accomplish this, for small periods of time, the MC65 alternately enables and disables battery charging to
keep the battery at acceptable temperatures. The MC65 indicates when charging is disabled due to abnormal
temperatures via its LED. See Table 1-1 on page 1-6.
2 - 16 MC65 Integrator Guide
Wall Mount Bracket
Use the optional Wall Mount Bracket to mount a four slot cradle to a wall. To attach the Wall Mount Bracket:
1.
Use the Wall Mount Bracket as a template and mark the locations of the four mounting screws.
NOTE Use fasteners appropriate for the type of wall and the Wall Mount Bracket mounting slots. The Wall Mount
Bracket mounting slots are designed for a fastener with a #8 pan head. Fasteners must be able to hold a
minimum of 4.9 Kg (10.8 lbs).
2.
Mount the fasteners to the wall. The screw heads should protrude about a half of an inch from the wall.
3.
Slip the Wall Mount Bracket over the screw heads and slide the bracket down over the screw heads.
4.
Tighten the screws to secure the bracket to the wall.
Mounting Tab (2)
Mounting Screw (4)
Mounting Slot
Figure 2-15 Wall Mount Bracket
To mount a four slot cradle:
1.
Screw the supplied screws into the bottom of the four slot cradle. The screw heads should protrude about
a quarter of an inch from the cradle.
Four Slot
Cradle Bottom
Mounting Screw (2)
Figure 2-16 Cradle Mounting Screws
2.
Align the Wall Mount Bracket mounting tabs with the mounting slots in the back of the four slot cradle. Slip
the two mounting tabs into mounting slots.
Accessories 2 - 17
3.
Swing the four slot cradle down onto the mounting bracket and align the mounting screws so that they fit
into the screw slots.
Wall Mount
Bracket
Screw Slots
Power Supply
Well
Figure 2-17 Wall Mount Bracket
4.
Tighten the mounting screws to secure the four slot cradle to the bracket.
Figure 2-18 Mounting Screws
5.
Connect power (see Figure 2-14 on page 2-15). The power supply should be located in the power supply
well.
2 - 18 MC65 Integrator Guide
VCD5500 Vehicle Cradle
This section describes how to set up and use a VCD5500 vehicle cradle with the MC65.
Once installed in a vehicle, the cradle:
• holds the MC65 securely in place
• provides power for operating the MC65
• re-charges the battery in the MC65.
Requirements
For mounting:
• four #8-32 self-locking nuts
• four #8 washers
• a drill with a #6 drill bit (.204”).
For power connection:
• power input cable (optional), p/n 25-61987-01R or 25-128974-01R
• UL Listed in-line fuse rated 250V, 5A (included), must be used if not connecting to vehicle’s fuse panel
• in-line fuse holder (included), must be used if not connecting to vehicle’s fuse panel.
Connector Pin-Outs
Table 2-5 Power Input Cable
Pin
Signal
1
Chassis ground (Black Wire)
2
Chassis ground (Bare Wire)
3
V+ (Red Wire)
4
V+ (Red Wire)
1
Connector on Power Cable
CAUTION
ROAD SAFETY - Do not use the MC65 while driving. Park the vehicle first. Always ensure the
MC65 is fully inserted into the cradle. Do not place it on the seat or where it can break loose in a
collision or sudden stop. Lack of proper insertion may result in property damage or personal injury.
Motorola, Inc. is not responsible for any loss resulting from the use of the products while driving.
Remember: Safety comes first.
Mounting the Cradle
CAUTION
Only mount the Vehicle Cradle in a vertical position with the release level at the top or in a horizontal
position with the MC65 display facing up. Never mount the vehicle cradle on the side or upside down or
on a wall that can be subject to impact or collision of greater than 40Gs, in accordance with SAE J1455
Section 4.10.3.5
Accessories 2 - 19
1.
Select a mounting location for the cradle. It should be flat, and must provide adequate support for the
cradle.
NOTE If using the GPS functionality of the MC65, ensure that the vehicle cradle is positioned so that the MC65
has a clear unobstructed view of the sky.
2.
Prepare the mounting surface to accept four #8-32 studs, using the mounting template below. Drill four
holes with a #6 drill bit.
1.2”
1.5”
Figure 2-19 Vehicle Cradle Mounting Template
3.
Position the cradle on the mounting surface.
4.
Fasten it using four #8 washers and four #8-32 self-locking nuts.
CAUTION
Do not install a VCD5500 Vehicle Cradle on or near an air bag cover plate or within an aerobic zone.
Also, do not install it in a location that affects vehicle safety or driveability.
Power Connection
Please read all of the following instructions before beginning.
WARNING! A properly trained technician must perform the power connection. Improper connection can
damage your vehicle, cradle or MC65. Refer to the vehicle’s Owner’s Manual for instructions for
removing power.
To connect the cradle to power:
CAUTION
1.
When setting up connection for this cradle, only use the power input cable, part number 25-61987-01R
or 25-128974-01R.
Locate the vehicle power source.
NOTE The ideal location for connecting the vehicle cradle power input cable would be an accessory output in
your vehicle’s fuse panel. The vehicle cradle should be added to a circuit with a maximum load capacity
for the cradle and the original circuit. Refer to the vehicle’s Owner’s Manual for identification of the circuit.
If a fused output is not available, the vehicle cradle must be installed with the provided in-line fuse holder
and UL Listed 5A fuse. The fuse protects the vehicle from an electrical short on the power line to the
cradle.
To use the cradle to charge the MC65 and spare battery, when the vehicle’s ignition is off, connect the
cradle to unswitched power.
2 - 20 MC65 Integrator Guide
2.
Route the power input cable from the cradle’s power port to the connection point for the vehicle’s power
source.
CAUTION
3.
The means of routing and securing the power input cable from the cradle through to the vehicle power
source is extremely important. Hazards associated with improper wiring can be severe. To avoid
unintentional contact between the wire and any sharp edges, provide the cable with proper bushings
and clamping where it passes through openings. If the wire is subjected to sharp surfaces and excess
engine vibration, the wiring harness insulation can wear away, causing a short between the bare wire
and chassis. This can start a fire.
To avoid any mishaps, all wiring should be routed away from moving parts, high temperature areas and
any contaminants.
When using the supplied in-line fuse holder (which must be used if not connecting to vehicle’s fuse panel):
a.
Ensure the fuse holder contains a 5A UL Listed slow-blow fuse.
b.
Splice the fuse holder to the end of the red V+ wire, as shown above. Make the distance from the fuse
to the power connection point as short as possible.
Ground
Wire (black)
5A Fuse and
Fuse Holder
Shield Wire
(bare wire)
V+ Power (red)
Figure 2-20 Vehicle Cradle Power Connection
4.
Prepare the cable termination.
a.
Red wire: connect to a +12/24 V vehicle power source.
b.
Black wire and Shield wire: connect to vehicle ground wire or chassis ground.
NOTE How the cable terminates depends on the vehicle. If the vehicle has a power output connector, then you
must attach a mating connector to the end of the power cable. You may be able to connect to a fuse panel
with a simple blade terminal or commercially available connector. Consult the vehicle Owner’s Manual for
information on how to access the power supply in the vehicle.
5.
Connect the power input cable into the power port on the cradle.
To see if the cradle has power, insert the MC65. The Charging LED on the MC65 blinks slowly to indicate
charging and turns solid amber when the battery is completely charged. See Table 1-1 on page 1-6 for other
indications.
Accessories 2 - 21
Charging the MC65 Battery
Insert the MC65 into the vehicle cradle to begin charging. A click indicates that the MC65 button release
locking mechanism is enabled and the MC65 is locked in place.
Release Lever
Figure 2-21 MC65 Battery Charging
CAUTION
Ensure the MC65 is fully inserted in the cradle. Lack of proper insertion may result in property damage
or personal injury. Motorola, Inc. is not responsible for any loss resulting from the use of the products
while driving.
Removing the MC65
To remove the MC65, press the release levers on the cradle and pull the MC65 up and out of the cradle.
Release Lever
Figure 2-22 Removing the MC65
2 - 22 MC65 Integrator Guide
Battery Charging Indicators
The MC65’s charge LED indicates the status of the battery charging in the MC65. See Table 1-1 on page 1-6
for charging status indications.
The 3600 mAh battery charges in approximately six hours.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the
MC65.
To accomplish this, for small periods of time, the MC65 alternately enables and disables battery charging to
keep the battery at acceptable temperatures. The MC65 indicates when charging is disabled due to abnormal
temperatures via its LED. See Table 1-1 on page 1-6.
Accessories 2 - 23
Four Slot Battery Charger
This section describes how to use the Four Slot Battery Charger to charge up to four MC65 spare batteries.
Spare Battery Charging
1.
Connect the charger to a power source.
2.
Insert the spare battery into a spare battery charging well and gently press down on the battery to ensure
proper contact.
Battery Charging
LEDs (4)
Battery
Figure 2-23 Four Slot Spare Battery Charger
Battery Charging Indicators
An amber LED is provided for each battery charging well. See Table 2-6 for charging status indications. The
3600 mAh battery charges in approximately six hours.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the
charger in order to ensure safe operation and optimize long-term battery life.
To accomplish this, for small periods of time, the charger alternately enables and disables battery charging to
keep the battery at acceptable temperatures. The charger indicates when charging is disabled due to abnormal
temperatures via its LED. See Table 2-6.
2 - 24 MC65 Integrator Guide
Table 2-6
Spare Battery LED Charging Indicators
LED
Indication
Off
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
Fast Blinking Amber
Error in charging; check placement of spare battery.
Slow Blinking Amber
Spare battery is charging.
Solid Amber
Charging complete.
Accessories 2 - 25
Cables
This section describes how to set up and use the cables. The cables are available with a variety of connection
capabilities.
The following communication/charge cables are available:
• USB Charging cable
• Charge Only cable
• Auto Charge cable.
USB Charging Cable
The USB Charging cable provides the MC65 with operating and charging power when used with the Motorola
approved power supply and AC line cord and synchronize information between the MC65 and a host
computer.
Figure 2-24 USB Charging Cable
Charge Only Cable
The Charge Only cable provide the MC65 with operating and charging power when used with the Motorola
approved power supply.
2 - 26 MC65 Integrator Guide
Figure 2-25 Charge Only Cable
Auto Charge Cable
The Auto Charge cable plugs into a vehicle cigarette lighter and provide the MC65 with operating and charging
power.
Figure 2-26 Auto Charge Cable
Connecting to the MC65
1.
If required, connect the cable power input connector to the Motorola approved power source.
2.
Slide the bottom of the MC65 into the connector cup end of the cable until the MC65 is firmly seated in the
cup.
3.
Slide the two locking tabs up until they both lock into position.
Accessories 2 - 27
Locking Tab
Figure 2-27 Cable Cup Locking Tabs
4.
To remove, slide the two locking tab down and remove the cable from the MC65.
Battery Charging Indicators
The MC65 amber Charge LED indicates the MC65 battery charging status. The 3600 mAh battery charges in
less than six hours. See Table 1-1 on page 1-6 for charging status indications.
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the
MC65.
To accomplish this, for small periods of time, the MC65 alternately enables and disables battery charging to
keep the battery at acceptable temperatures. The MC65 indicates when charging is disabled due to abnormal
temperatures via its LED. See Table 1-1 on page 1-6.
2 - 28 MC65 Integrator Guide
Vehicle Holder
WARNING!
Some countries prohibit the mounting of any electronic device in any location on the vehicle
dashboard and windshield. Be sure to check your local laws acceptable mounting areas
before installing the auto mounting kit.
Installation Reminders
Figure 2-28 Vehicle Holder Mounting
• Do not mount the vehicle holder where it will obscure the driver’s view of the road.
• Do not mount the vehicle holder near the driver seat air bag deployment area.
• Do not place the MC65 on top of the dashboard or anywhere without securing it in the vehicle holder.
• Do not mount the vehicle holder near the passenger seat air bag deployment area.
• Install the vehicle holder on the surface of your vehicle that is reasonably flat and free of dirt and oil.
Device Mounting Precautions
• Some countries prohibit the mounting of any electronic device in any location on the vehicle dashboard.
Be sure to check your local laws acceptable mounting areas before installing the vehicle holder.
• The heating and cooling cycle of a vehicle’s interior will in some cases loosen the adhesion of the suction
cup. Check the vacuum seal of the vehicle mount kit for adequate adhesion each time you use the unit,
and reinstall if necessary.
• If the vehicle holder has problems staying on, clean the plastic suction cup with alcohol, then reinstall.
Installation
Install the vehicle mount on the surface of your vehicle that is reasonably flat and free of dirt and oil. Clean the
mounting surface with a glass cleaner and a clean cotton cloth. Install the vehicle mount on the windshield or
other flat car surface using the supplied mounting disc.
Accessories 2 - 29
Assembly
1.
Insert the vehicle holder’s cradle plate to the holes on the back of the cradle.
2.
Push the cradle down until both parts are engaged.
Windshield Installation
1.
Fix the suction cup mount to the selected area with the suction lever facing up.
Suction Cup Mount
Cradle Plate
Cradle
Figure 2-29 Windshield Installation
2.
Flip the lever down to create a vacuum between the suction cup and the mounting surface.
3.
Make sure that the suction bond is strong enough before proceeding to the next step.
4.
Slide the MC65 into the cradle.
2 - 30 MC65 Integrator Guide
Locking Tab
Figure 2-30 Insert MC65 into Vehicle Holder
5.
Connect the auto charger cable to the MC65 and slide the two locking tabs up to secure the cable cup to
the MC65.
6.
Connect the other end to the cigarette lighter socket.
The LED indicator on the right side of the touch screen lights up orange during charging.
NOTE Prior to removing the MC65 from the vehicle holder, disconnect the auto-charge cable from the MC65.
Flat Surface Installation
1.
Remove the plastic sheet on the bottom of the mounting disc.
2.
Place the disc, sticky side down, on a clean flat surface.
Figure 2-31 Mounting Disc
3.
Fix the suction cup mount to the disc with the suction lever facing up.
4.
Flip the lever down to create a vacuum between the suction cup and the disc.
Accessories 2 - 31
5.
Make sure that the suction bond is strong enough before proceeding to the next step.
6.
Slide the MC65 into the cradle.
Figure 2-32 Vehicle Holder Mounted on Flat Surface
7.
Connect the auto charger cable to the MC65 and slide the two locking tabs up to secure the cable cup to
the MC65.
8.
Connect the other end to the cigarette lighter socket.
The LED indicator on the right side of the touch screen lights up orange during charging.
2 - 32 MC65 Integrator Guide
CHAPTER 3 ACTIVESYNC
Introduction
To communicate with various host devices, install Microsoft ActiveSync (version 4.5 or higher) on the host
computer. Use ActiveSync to synchronize information on the MC65 with information on the host computer.
Changes made on the MC65 or host computer appear in both places after synchronization.
NOTE When an MC65 with Windows Mobile 6.5 is connected to a host computer and an ActiveSync connection
is made, the WLAN radio (if applicable) is disabled. This is a Microsoft security feature to prevent
connection to two networks at the same time.
ActiveSync software:
• Allows working with mobile computer-compatible host applications on the host computer. ActiveSync
replicates data from the MC65 so the host application can view, enter, and modify data on the MC65.
• Synchronizes files between the MC65 and host computer, converting the files to the correct format.
• Backs up the data stored on the MC65. Synchronization is a one-step procedure that ensures the data is
always safe and up-to-date.
• Copies (rather than synchronizes) files between the MC65 and host computer.
• Controls when synchronization occurs by selecting a synchronization mode, e.g., set to synchronize
continually while the MC65 is connected to the host computer, or set to only synchronize on command.
• Selects the types of information to synchronize and control how much data is synchronized.
Installing ActiveSync
To install ActiveSync on the host computer, download version 4.5 or higher from the Microsoft web site at
http://www.microsoft.com. Refer to the installation instructions included with the ActiveSync software.
3-2
MC65 Integrator Guide
MC65 Setup
NOTE Microsoft recommends installing ActiveSync on the host computer before connecting the MC65.
The MC65 by default is set up to communicate through a USB connection. Chapter 2, Accessories provides
the accessory setup and cable connection information for use with the MC65. The MC65 communication
settings must be set to match the communication settings used with ActiveSync.
1.
On the MC65 tap Start > ActiveSync icon.
2.
Tap Menu > Connections.
3.
Select the connection type from the drop-down list.
4.
Tap OK to exit the Connections window and tap OK to exit the ActiveSync window.
5.
Proceed with installing ActiveSync on the host computer and setting up a partnership.
ActiveSync
3-3
Setting Up an ActiveSync Connection on the Host Computer
To start ActiveSync:
1.
Select Start > Programs > Microsoft ActiveSync on the host computer. The ActiveSync Window displays.
Figure 3-1 ActiveSync Window
NOTE Assign each MC65 a unique device name. Do not try to synchronize more than one MC65 to the same
name.
2.
In the ActiveSync window, select File > Connection Settings. The Connection Settings window appears.
Figure 3-2 Connection Settings Window
3.
Select Allow USB connections checkbox.
4.
Select the Show status icon in Taskbar check box.
5.
Select OK to save any changes made.
Synchronization the MC65
NOTE When a MC65 with Windows Mobile 6.5 is connected to a host computer and an ActiveSync connection is
made, the WLAN radio (if applicable) is disabled. This is a Microsoft security feature to prevent connection
to two networks at the same time.
3-4
MC65 Integrator Guide
To synchronize:
1.
If the Get Connected window does not appear on the host computer, select Start > All Programs > Microsoft
ActiveSync.
Figure 3-3 Synchronization Setup Wizard Window
2.
Click Next.
Figure 3-4 Synchronization Directly With a Server Window
3.
Select the check box to synchronize with a server running Microsoft Exchange if applicable.
4.
Click Next.
ActiveSync
Figure 3-5 Synchronization Option Window
5.
Select the appropriate settings and click Next.
Figure 3-6 Wizard Complete Window
6.
Click Finish.
Figure 3-7 ActiveSync Connected Window
3-5
3-6
MC65 Integrator Guide
During the first synchronization, information stored on the MC65 is copied to the host computer. When the copy
is complete and all data is synchronized, the MC65 can be disconnect from the host computer.
NOTE The first ActiveSync operation must be performed with a local, direct connection. Windows Mobile retains
partnerships information after a reset.
For more information about using ActiveSync, start ActiveSync on the host computer, then see ActiveSync
Help.
CHAPTER 4 APPLICATION DEPLOYMENT
Introduction
This chapter describes features in Windows Mobile including new security features, how to package
applications, and procedures for deploying applications onto the MC65.
Security
The MC65 implements a set of security policies that determine whether an application is allowed to run and, if
allowed, with what level of trust. To develop an application, you must know the security configuration of the
device, and how to sign an application with the appropriate certificate to allow the application to run (and to run
with the needed level of trust).
Application Security
Application security controls the applications that can run on the MC65.
• Trusted - All applications must be digitally signed by a certificate on the MC65.
• Prompted - User is prompted to allow unsigned applications to run.
• Open - All applications run.
Developers can include their own certificates and provision the device to “trusted.”
Digital Signatures
Digital signatures provide a way to authenticate the author of EXEs, DLLs, and packages. Digitally signed
applications give users confidence that an application comes from where they think it comes from. For
example, if an end-user downloads an update package from the internet that is digitally signed with Motorola's
software certificate, they are assured that the package is authentic and that it was created by Motorola. By
enforcing the use of digital signatures, users can also prevent malicious applications from executing on the
MC65. For example, users can provision the MC65 to only execute “trusted” applications (digitally signed).
Motorola ships all Windows Mobile 6 based products in an “open” state, which means all signed and unsigned
applications should work. However, customers can still reconfigure their MC65 to operate in the “trusted”
4-2
MC65 Integrator Guide
mode. This means that only applications signed with a certificate from the Privileged Execution Trust
Certificate Store can run.
To support the broadest number of deployments, third-party software developers should perform the following
when releasing software for a Windows Mobile 6 devices:
• Sign all their EXEs & DLLs with their private key
• Provide the corresponding public certificate to end-users so that it can be installed into Privileged
Execution Trust Certificate Store.
If the software is installed via a .CAB file, developer should also:
• Sign the .CAB file with their private key
• Provide the corresponding public certificate to end-users so that it can be installed into SPC Certificate
Store.
Locking Down a Mobile Computer
Like most configuration options in Windows Mobile, security settings are set via XML provisioning. For
example, to enforce the “trusted” model and only allow applications signed with a privileged certificate to run,
use the following provisioning document:
<wap-provisioningdoc>
<characteristic type=”SecurityPolicy”>
<!-- Disallow unsigned apps -->
<parm name= “4102” value= “0”/>
<!-- No Prompt -->
<parm name= “4122” value= “1”/>
</characteristic>
</wap-provisioningdoc>
For more information on various security options, refer to the Security Policy Settings topic in the latest
Windows Mobile documentation.
Application Deployment
4-3
Installing Certificates
Use XML provisioning to query and delete certificates from certificate stores. To add a new certificate the
Privileged Execution Trust Certificate Store, use the following sample provisioning document:
<wap-provisioningdoc>
<characteristic type= “CertificateStore”>
<characteristic type= “Privileged Execution Trust Authorities”>
<characteristic type= “657141E12FA45786F6A57CA6464032D4B3A55475”>
<parm name= “EncodedCertificate” value= “
This is sample text. This is sample text. This is sample text. This is sample text.
This is sample text. This is sample text. This is sample text. This is sample text.
This is sample text. This is sample text. This is sample text. This is sample text. = “/>
</characteristic>
</characteristic>
</characteristic>
</wap-provisioningdoc>
To create your own provisioning document with real certificate information:
1.
Obtain a certificate from a security provider such as VeriSign.
2.
Double-click on the certificate file (.CER) to open it.
3.
Click on the Details tab and locate the Thumbprint field.
4.
Copy the contents of the Thumbprint field and replace the value in the XML example above.
5.
Click the Copy to File… button.
6.
Click Next to start the Certificate Export Wizard.
7.
Select Base-64 encoded X.509 (.CER) and then click Next.
8.
Set the File Name to CertOutput.xml and click Next.
9.
Click Finish to export the certificate.
10. Open the exported file, CertOutput.xml, in a text editor (i.e., NotePad).
11. Copy the contents of the file (excluding the first line, last line, and CR/LF) and replace the value of the
“EncodedCertificate” parameter in the xml example above.
Device Management Security
You can control access to certain device settings and security levels, such as installing applications and
changing security settings. Refer to the Windows Mobile Version 6 Help file for information on device
management security.
Remote API Security
The Remote API (RAPI) enables applications that run on a desktop to perform actions on a remote device.
RAPI provides the ability to manipulate the file system on the remote device, including the creation and
deletion of files and directories. By default, Motorola ships with RAPI in the restricted mode. Certain tools, such
4-4
MC65 Integrator Guide
as RAPIConfig, may not work properly. Refer to the Windows Mobile Version 6 Help file for finding information
on Remote API security policies.
Packaging
NOTE Applications compiled for Windows Mobile 6 are not backward-compatible with previous versions.
Packaging combines an application's executable files into a single file, called a package. This makes it easier
to deploy and install an application to the MC65. Package new applications and updates, such as new DLL
files, as CAB files, then deploy them to devices. Refer to the Microsoft Windows Mobile 6 Help file for
information on CAB files.
Deployment
To install applications onto the MC65, developers package the application and all required files into a CAB file,
then load the file onto the MC65 using one of the following options:
• Microsoft ActiveSync 4.5 or higher
• Storage Card
• MSP
• AirBEAM
• Image Loader Image (for updating the operating system).
Refer to the Microsoft Windows Mobile 6 Help file for information on CAB files.
Installation Using ActiveSync
To install an application package:
• Connect the MC65 to a host computer using ActiveSync. See Chapter 3, ActiveSync for more
information.
• Locate the package file on the host computer.
• In ActiveSync on the host computer, open Explorer for the MC65.
• Copy the CAB file from the host computer to the \temp directory on the MC65.
• On the MC65, navigate to the \temp directory.
• Tap on the application CAB file. The application installs on the MC65.
Installation Using Storage Card
To install an application package:
• Copy the package CAB file to a microSD storage card using an appropriate storage card reader.
• Install the storage card into the MC65. See Installing a microSD Card on page 1-2 for more information.
• On the MC65, open File Explorer.
Application Deployment
4-5
• Open the Storage Card directory.
• Tap the package CAB file. The application installs on the MC65.
Installation Using AirBEAM
The AirBEAM Smart Client provides backward-compatible legacy AirBEAM functionality and
backward-compatible legacy MSP 2.x Level 2 Agent functionality.
Refer to the AirBEAM Smart Windows CE Client Product Reference Guide, p/n 72-63060-xx, for instructions
for AirBEAM Smart client.
MSP
The MSP 3 Client Software is a set of software components that come pre-installed on the MC65. The MSP 3
Client software consists of the following components:
The RD Client provides support for MSP 3 Staging functionality, provides support for the MSP 3 Legacy
Staging process, and provides support for backward-compatible legacy MSP 2.x Legacy Staging functionality.
The MSP 3 Agent provides MSP 3 Provisioning functionality and Control functionality when used with MSP 3.2
Control Edition.
Refer to the Mobility Services Platform 3.2 User’s Guide, p/n 72E-100158-xx, for instructions for using the
Rapid Deployment and MSP3 Agent clients.
Update Loader Image
Windows Mobile contains an Image Update feature that updates all operating system components. All updates
are distributed as update packages. Update packages can contain either partial or complete updates for the
operating system. Motorola distributes the update packages on the Support Central Web Site,
http://supportcentral.motorola.com.
To update an operating system component, copy the update package to the MC65 using one of a variety of
transports, including ActiveSync, an microSD card, AirBEAM or MSP.
Download Update Loader Package
1.
Go to the Motorola Support Central web site, http://supportcentral.motorola.com.
2.
Download the appropriate update loader package to a host computer.
3.
Locate the update loader package file on the host computer and un-compress the file into a separate
directory.
ActiveSync
To install an update loader package using ActiveSync:
1.
Connect the MC65 to a host computer using ActiveSync. See Chapter 3, ActiveSync for more information.
2.
In ActiveSync on the host computer, open Explorer for the MC65.
3.
Copy all the update loader package files from the host computer to the \temp directory on the MC65.
4.
On the MC65, navigate to the \temp directory.
5.
Tap on the update loader file, STARTUPDLDR.EXE. The Update Loader application installs the update
loader package on the MC65.
4-6
MC65 Integrator Guide
A progress bar displays until the update completes.
6.
The MC65 re-boots.
7.
The calibration screen appears.
microSD Card
To install an update loader package using a microSD card:
1.
Copy all the update loader package files to the root directory of a microSD card.
2.
Install the microSD card into the MC65. See Installing a microSD Card on page 1-2 for installation
instructions.
3.
Connect the MC65 to AC power. See Chapter 2, Accessories.
4.
Perform a reset.
5.
Immediately, as soon as the device starts to boot and before the splash screen is visible, press and hold
the left scan button.
6.
The Update Loader application looks for the update loader file in the root directory of the microSD card.
When it finds the file, it loads the update loader package onto the MC65. A progress bar displays until the
update completes.
7.
The MC65 re-boots.
8.
The calibration screen appears.
XML Provisioning
To configure the settings on an MC65, use XML provisioning. To install an XML provisioning file on the MC65,
create a Cabinet Provisioning File (CPF). A CPF file is similar to a CAB file and contains just one file:
_setup.xml. Like a CAB file, the CPF extension is associated with WCELoad.EXE. Opening a CPF extracts the
XML code and uses it to provision and configure the MC65. The user receives an e-mail notification indicating
success or failure.
XML provisioning provides the ability to configure various features of the MC65 (i.e., registry and file system).
However, some settings require security privileges. To change registry settings via a CPF file, you must have
certain privileges (roles). Some registry keys require you to simply be an Authenticated User, while other
registry keys require you to be a Manager. Refer to the Microsoft Windows Mobile 6 Help file, Metabase
Settings for Registry Configuration Service Provider section, for the default role settings in Windows Mobile 6.
For those registry settings that require the Manager role, the CPF file must be signed with a privileged
certificate installed on the device. Refer to the Microsoft Windows Mobile 6 Help file and the Windows Mobile 6
SDK for instructions and sample test certificates.
Creating an XML Provisioning File
To create a .cpf file:
1.
Create a valid provisioning XML file named _setup.xml using an XML editor or the tools supplied with
Visual Studio 2005. (For example, use the SampleReg.xml sample created in the RegMerge on page 4-7
section and rename it _setup.xml.) Ensure the file contains the required parameters for the operation.
Refer to the Microsoft Windows Mobile 6 Help file for information.
Application Deployment
2.
4-7
In the Windows Mobile 6 tools directory on the desktop computer (typically \Program Files\Windows CE
Tools\wce500\Windows Mobile 6 Pocket PC SDK\Tools), run the Makecab.exe utility, using the following
syntax to create a .cpf file from the _setup.xml file:
MakeCab.exe /D COMPRESS=OFF _setup.xml myOutCpf
NOTE COMPRESS=OFF is required for backward compatibility with Pocket PC.
3.
Optionally, use the Authenticode tools to sign the .cpf file.
4.
Tap the filename to install.
5.
Certain applications and settings require a reset to take affect. In these cases, reset the MC65. Refer to the
Windows Mobile Version 6 Help file for more information.
XML Provisioning vs. RegMerge and Copy File
Prior to Windows Mobile 5.0, Motorola used two drivers (RegMerge and CopyFiles) to update the registry and
to copy files during a reset. With Windows Mobile 6, Motorola recommends using XML provisioning instead.
RegMerge and CopyFiles are supported for backward compatibility but Motorola may eliminate support in the
future. The following sections provide examples of how RegMerge and CopyFiles were used, and how to
perform the same function using XML provisioning.
RegMerge
RegMerge.dll is a built-in driver that allows updating the registry during a clean boot. RegMerge runs very early
in the boot process and looks for registry files (.reg files) in certain Flash File System folders (i.e., \Application)
during a clean boot. It then merges the registry changes into the system registry located in RAM.
The following example uses RegMerge to set a registry key:
SampleReg.reg
[HKEY_LOCAL_MACHINE\Hardware\DeviceMap\Backlight]
“BacklightIntensity”=dword:00000036
The following example uses XML provisioning to perform the same task:
SampleReg.xml
<wap-provisioningdoc>
<characteristic type= “Registry”>
<characteristic type= “HKLM\Hardware\DeviceMap\Backlight”>
<parm name= “BacklightIntensity” value= “54” datatype= “integer” />
</characteristic>
</characteristic>
</wap-provisioningdoc>
CopyFiles
CopyFiles copies files from one folder to another on a clean boot. During a clean boot CopyFiles looks for files
with a .CPY extension in the root of the Application FFS partition. These files are text files containing the
source and destination for the desired files to copy, separated by “>”.
The following example uses CopyFiles to copy a file from the \Application folder to the \Windows folder:
4-8
MC65 Integrator Guide
SampleCpy.cpy
\Application\example.txt > \Windows\example.txt
The following example uses XML provisioning to perform the same task:
SampleCpy.xml
<wap-provisioningdoc>
<characteristic type= “FileOperation”>
<characteristic type= “\Windows” translation= “filesystem”>
<characteristic type= “MakeDir”/>
<characteristic type= “example.txt” translation= “fileystem”>
<characteristic type= “Copy”>
<parm name= “Source” value= “\Application\example.txt” translation= “filesystem”/>
</characteristic>
</characteristic>
</characteristic>
</characteristic>
</wap-provisioningdoc>
Storage
Mobile 6 contains three types of file storage:
• Random Access Memory (RAM)
• Persistent Storage
• Application folder.
Random Access Memory
Executing programs use RAM to store data. Data stored in RAM is lost upon a warm boot. RAM also included
a volatile file storage area called Cache Disk.
Volatile File Storage (Cache Disk)
Windows Mobile 6 memory architecture uses persistent storage for all files, registry settings, and database
objects to ensure data is retained even after a power failure. Persistent storage is implemented using Flash
memory technology which is generally slower than volatile RAM memory. In certain situations the speed of the
operation is more important than the integrity of the data. For these situations, Motorola has provided a small
volatile File Storage volume, accessed as the Cache Disk folder. Disk operations to the Cache Disk folder are
much faster than to any of the persistent storage volumes, but data is lost across warm boots and power
interruptions. Note that a backup battery powers RAM memory, including the Cache Disk, when you remove
the main battery for a short period of time.
The MC65 uses the Cache Disk for temporary data that can be restored from other sources, for example, for
temporarily “caching” HTML web pages by a browser or generating formatted files to send to a printer. Both
situations benefit from the increased speed of the cache disk, but you can restore the data if needed.
DO NOT use the Cache Disk as a method to improve application performance. Analyze applications that
perform slower in persistent storage to optimize disk access. Common areas for optimization include
Application Deployment
4-9
minimizing the number of reads and writes to a file, removing unneeded debug logging, and minimizing file
flushing or closing files.
Persistent Storage
Windows Mobile 6 protects all data and applications from power-related loss. Because Windows Mobile 6
mounts the entire file system and registry in persistent storage (rather than using RAM), MC65 devices provide
a reliable storage platform even in the absence of battery power.
Persistent storage provides application developers with a reliable storage system available through the
standard file system and registry APIs. Persistent storage is optimized for large reads and writes; therefore,
applications reading and writing data in large chunks tend to outperform those applications reading and writing
small blocks of data. Data in persistent storage is lost upon a reset.
Persistent storage contains all the directories under the root directory except for Application, Cache Disk, and
Storage Card (if a storage card is installed). Persistent storage is approximately 650 MB (formatted).
Application Folder
The Application folder is a super-persistent storage that is persistent even after a reset. Accessing data in the
Application folder is slower than accessing persistent storage. The Application folder is used for deployment
and device-unique data. For example, network profiles can be stored in the Application folder so that
connection to the network is available after a reset. The Application folder is approximately 96 MB (formatted).
Enterprise Mobility Developer Kits
The Motorola Enterprise Mobility Developer Kit (EMDK) family of products allows you to write applications that
take advantage of the capture, move and manage capabilities of the MC65. Go to the Support Central
(http://supportcentral.motorola.com) to download the appropriate developer kit.
4 - 10 MC65 Integrator Guide
CHAPTER 5 PHONE SETUP
Introduction
If the cellular service is with AT&T, Telcel, Bell Mobility, Telstra, or any other operator that supplies a SIM card,
install the SIM card into the MC65. Refer to Installing the SIM Card on page 1-3 for more information. Note that
first-time power-up may take up to five minutes, as the MC65 automatically configures itself for the carrier.
If the cellular service is with a carrier that requires calling-in for activation, such as Verizon or Sprint, activate
using the Phone Network Setup application. It may take 10 to 15 minutes to complete the activation the first
time. Note that another phone needs to be available, for calling your wireless operator’s customer service
department. Also, the MC65 needs to be in-coverage, i.e. in the service area, of your wireless operator, for it’s
activation process to complete.
If the user has a Global Phone service with Verizon or Sprint, and has a SIM card as part of the service,
power-up the MC65 and complete activation, without inserting the SIM card. Insert the SIM card afterwards.
The Phone Network Setup application provides the ability to change networks when detected: by the MC65
or manually: when the user decides to change networks.
Automatic Network Setup
See Network Activation on page 1-7 for information on activating the MC65 upon startup.
Manual Network Setup
NOTE On OEM version 01.121.0X, when an AT&T SIM card is installed in the MC65, the user interface for the
CDMA settings is hidden. To restore access to these settings, please contact Motorola Enterprise Mobility
Support.
CDMA Network Setup
NOTE Upon a Master Reset or a software upgrade, CDMA users must restore data services and MMS settings.
Tap Start > Setting > Connections > Phone Network Setup. On the Band tab, tap Network Type and
select either CDMA Only or CDMA First.
To manually configure the MC65 for a CDMA network:
1.
Tap Start > Setting > Connections > Phone Network Setup.
5-2
MC65 Integrator Guide
2.
On the Band tab, select the Network Type:
• CDMA Only - Searches for only CDMA networks. GSM/UMTS networks are ignored.
• CDMA First - Searches first for CDMA networks and then for GSM/UMTS networks if CDMA networks
are not found.
3.
On the CDMA Setup tab, tap Preferred network and select your carrier.
4.
Tap Start Activation button.
5.
On the Phone Network - CDMA Activation dialog box, tap Yes.
6.
On an active phone line, call your carrier to active the MC65. Provide the MEID number on the screen to
the customer representative.
7.
When requested, tap Activate Now to activate the MC65.
GSM Network Setup
To manually configure the MC65 for a GSM/UMTS network:
1.
Install an active SIM card into the MC65. Refer to Installing the SIM Card on page 1-3.
2.
Tap Start > Setting > Connections > Phone Network Setup.
3.
On the Band tab, select the Network Type:
• GSM/UMTS Only - Searches for only GSM/UMTS networks. CDMA networks are ignored.
• GSM/UMTS First - Searches first for GSM/UMTS networks and then for CDMA networks if GSM/UMTS
networks are not found.
4.
Select GSM/UMTS Preferred and select:
• Auto (GSM & UMTS) - Searches for either GSM or UMTS networks.
• GSM Only - Searches for only GSM networks.
• UMTS Only - Searches for only UMTS networks.
5.
Tap Band. Select:
• All - Configures the MC65 to use all bands.
• NA & CA - Configures the MC65 to use bands used in North America and Canada.
• EMEA/APAC - Configures the MC65 to use bands used in the Europe, Middle East, Africa (EMEA)
region, and Asia Pacific (APAC) region.
• Brazil - Configures the MC65 to use bands used in the Brazil region.
6.
On the GSM/UMTS tab, tap Preferred network and select your carrier.
7.
Tap the Update Connection Settings button.
NOTE SIM cards of supported carriers automatically configure the data connection and MMS settings upon
activation. Data connection and MMS settings for non-supported carriers must be manually configured.
See Configuring a GSM Data Connection on page 5-5 and refer to the MC65 User Guide for MMS set up
information.
The Public Land Mobile Network (PLMN) tab displays only when Network Type is set to GSM/UMTS Only.
Tap Show List to display the PLMN list.
Phone Setup
5-3
Dual Network Usage
The MC65 can be set up to be used on both a CDMA and GSM/UMTS networks and the user can switch
between them.
NOTE Each active network account uses its own phone number.
On OEM version 01.121.0X, when an AT&T SIM card is installed in the MC65, the user interface for the
CDMA settings is hidden. To restore access to these settings, please contact Motorola Enterprise Mobility
Support.
1.
Obtain an active GSM/UMTS SIM card.
2.
Activate the MC65 on a CMDA network. See CDMA Network Setup on page 5-1.
3.
Install the SIM card. See Installing the SIM Card on page 1-3.
To set the MC65 to use the CDMA network:
1.
Tap > Start > Setting > Connections > Phone network Setup.
2.
On the Band tab, tap Network type and select CDMA First or CDMA Only.
3.
Tap OK.
To set the MC65 to use the GSM/UMTS network:
1.
Tap > Start > Setting > Connections > Phone network Setup.
2.
On the Band tab, tap Network type and select GSM/UMTS First.
3.
On the GSM/UMTS tab, tap the Update Connection Settings button.
4.
Tap OK.
Switching Between CDMA Networks
If the MC65 was initially provisioned on the Verizon network it can be switched to another CDMA network. If the
MC65 is to be provisioned back to the Verizon network, additional carrier support is required. Contact the
Motorola Enterprise Mobility support for detailed information. See Service Information on page xiv.
Global Usage
CDMA networks can be used internationally will the use of a Global SIM card provided by the CDMA carrier.
After arriving, install the global SIM card into the MC65. See Installing the SIM Card on page 1-3.
To set the MC65 to use the global SIM card:
1.
Tap > Start > Setting > Connections > Phone network Setup.
2.
On the Band tab, tap Network type and select GSM/UMTS First.
3.
Tap GSM/UMTS Preferred and select Auto (GSM & UMTS), GSM Only or UMTS Only.
4.
Tap Band and select All, NA & CA, EMEA/APAC or Brazil.
5-4
MC65 Integrator Guide
5.
On the GSM/UMTS tab, tap the Update Connection Settings button.
NOTE If using an unsupported network, data connection and MMS settings must be manually configured. See
Configuring a GSM Data Connection on page 5-5 and refer to the MC65 User Guide for MMS set up
information.
6.
Tap OK.
7.
Upon return, remove the global SIM card.
8.
Tap > Start > Setting > Connections > Phone network Setup.
9.
On the Band tab, tap Network type and select CDMA First or CDMA Only.
10. Tap OK.
Phone Setup
Configuring a GSM Data Connection
NOTE SIM cards of supported carriers automatically configure the data connection upon activation. Data
connections for non-supported carriers must be manually configured.
A data connection allows Internet access across a wireless network.
To set up a new data connection:
1.
Acquire an Access Point Name (APN) from the service provider.
2.
Tap Start > Settings > Connections > Connections > Tasks.
3.
Under My ISP select Add a new modem connection.
4.
Enter a connection name in the Enter a name for the connection text box.
5.
Select Cellular Line (GPRS) from the Select a modem: drop-down list.
6.
Tap Next.
7.
Enter the APN from the service provider in the Access point name text box.
8.
Tap Next.
9.
Enter a username in the User name text box, if required by the service provider.
10. Enter a password in the Password text box, if required by the service provider.
11. Enter a domain name in the Domain text box, if required by the service provider.
12. Tap Finish.
13. Tap OK to exit Connections.
5-5
5-6
MC65 Integrator Guide
Phone Settings
Use the Phone Settings window to customize settings, such as the ring type and ring tone for incoming calls,
security options, and other options depending on the type of service.
Sounds
Use the Sounds tab to customize ring type, ring tone, keypad tone.
Tap Start > Settings > Personal > Phone > Sounds.
Figure 5-1 MC65 Phone Window - Phone Tab
1.
Select a ring type from the Ring type: drop-down list. The ring type changes the way the MC65 rings when
it receives an incoming call. Regardless of the ring type selected, a dialog box appears on the MC65’s
display for incoming calls.
2.
Select a ring tone for incoming calls from the Ring tone: drop-down list. To hear a sample of the selected
ring tone, tap
. Tap
to end the ring tone.
NOTE To use custom .wav, .mid, or .wma files as ring tones, use ActiveSync on the host computer to copy the
file to the /Windows/Rings folder on the MC65. Then select the sound from the ring tone list.
3.
Select a keypad tone from the Keypad: drop-down list. This selection determines the tone that sounds
when entering a phone number on the keypad.
Select Short tones or Long tones to specify the duration of the sound when you press a number on the
keypad. Select Off to disable tones.
NOTE Turning off sounds saves power and prolongs battery life.
Security
Enabling a PIN
Tap Start > Settings > Personal > Phone > Security.
NOTE Place emergency calls at any time, without requiring a PIN or a SIM card.
Phone Setup
5-7
Figure 5-2 Security Tab
To require a PIN when using the phone:
1.
Select the Require PIN when phone is used check box.
Figure 5-3 Enter PIN
2.
Use the dialer keypad to enter a four to eight digit PIN.
3.
Tap Enter to enable the PIN and return to the Security tab.
Changing a PIN
CAUTION
If the user enters an incorrect PIN, the message “SIM PIN incorrect: Try again” appears. After three
consecutive incorrect attempts, the SIM card is blocked. The phone does not allow entering a PIN
again and the user must obtain a PIN Unblock Key from the service provider.
1.
Tap Change PIN.
2.
Use the dialer keypad to enter the current PIN.
3.
Tap Enter.
4.
Use the dialer keypad to enter a new four to eight digit PIN.
5.
Tap Enter.
6.
Reenter the new PIN for confirmation and tap Enter.
7.
Tap OK to confirm the change.
5-8
MC65 Integrator Guide
Disabling a PIN
1.
Deselect the Require PIN when phone is used check box.
2.
Use the dialer keypad to enter the current PIN.
3.
Tap Enter.
4.
Tap OK to confirm the change and exit settings.
GSM Services
Use the GSM Services tab to configure settings for subscribed phone services. For example, block certain
types of incoming and/or outgoing calls ( page 5-8), disclose the caller’s identity when making outgoing calls (
page 5-8), forward incoming calls to a different phone number ( page 5-8), receive notification of incoming calls
when a phone session is in use ( page 5-9), and set up voice mail and short message service ( page 5-9).
1.
Tap Start > Settings > Personal > Phone> GSM Services.
Figure 5-4 Phone Window - GSM Services
2.
Select a service from the list and tap Get Settings... .
3.
Change services settings as follows.
Call Barring (Call Blocking)
Use call barring to block certain types of incoming and/or outgoing calls. Select the type of incoming and/or
outgoing calls to block.
Caller ID
Enable caller ID to reveal the identity of the person making an outgoing call. Select the Everyone radio button
to always display the caller ID. Select the No one radio button to prevent the caller’s identity from appearing to
others.
Call Forwarding
NOTE Call Forwarding may not be available on all networks. Check with the service provider for availability.
Use call forwarding to forward incoming calls to a different phone number.
Phone Setup
5-9
• To forward all calls to a different phone number:
• select the Forward all incoming phone calls check box.
• enter the phone number to receive forwarded calls in the To: text box.
• To forward incoming calls to a different phone number based on a specific situation, select one or more
of the check boxes under Forward phone calls only if:.
• No answer: enter the phone number to receive forwarded calls only when the phone cannot be
answered. Then select a time period from the Forward after: drop-down list. Options are 5, 10, 15, 20,
25, and 30 seconds.
• Unavailable: enter the phone number to receive forwarded calls only when the phone is turned off or
the user is unreachable.
• Busy: enter the phone number to receive forwarded calls only when the line is busy.
Call Waiting
NOTE Call Waiting may not be available on all networks. Check with your service provider for availability.
Call waiting notifies the user of an incoming call when the phone is in a phone session. Select the Notify me
radio button to enable call waiting. Select the Do not notify me radio button to disable call waiting.
Voice Mail and Text Messages
To use voice mail and send short messages, enter the voice mail and/or text message phone number in the
appropriate text boxes.
Fixed Dialing
Use Fixed Dialing to restrict the phone to dial only the phone number(s) or area code(s) specified in a Fixed
Dialing list.
1.
Select Fixed Dialing and tap Get Settings.
2.
Select the Enable fixed dialing check box.
3.
To add a number to the list, tap Menu > Add.
4.
Enter the phone number or area code to restrict and tap Done.
5.
Repeat steps 3 and 4 to add more numbers, and tap Done twice when complete.
6.
Enter PIN2 and tap Done.
NOTE PIN2 is buffered in the MC65 indefinitely after entry and will not be requested again until a reboot of the
MC65 has been performed. Should PIN2 be required, then the user must perform a reboot of the MC65.
5 - 10 MC65 Integrator Guide
Internet
Use the Internet tab to configure Internet calling.
Select an option from the down-down list.
Tap OK.
Services
Use the Services tab to set Broadcast Channels and GPDS Privacy features.
Broadcast Channels
Enable broadcast messages from local cell sites. These messages include emergency directions and
information services.
GPS Privacy
Allows internet applications to use current location.
HAC
Turn Hearing Aide Compatibility (HAC) on and off.
CHAPTER 6 MAINTENANCE &
TROUBLESHOOTING
Introduction
This chapter includes instructions on cleaning and storing the MC65, and provides troubleshooting solutions
for potential problems during MC65 operation.
Maintaining the MC65
For trouble-free service, observe the following tips when using the MC65:
• Do not scratch the screen of the MC65. When working with the MC65, use the supplied stylus or
plastic-tipped pens intended for use with a touch-sensitive screen. Never use an actual pen or pencil or
other sharp object on the surface of the MC65 screen.
Motorola recommends using a screen protector, p/n KT-129195-03R.
• The touch-sensitive screen of the MC65 is glass. Do not to drop the MC65 or subject it to strong impact.
• Protect the MC65 from temperature extremes. Do not leave it on the dashboard of a car on a hot day,
and keep it away from heat sources.
• Do not store or use the MC65 in any location that is dusty, damp, or wet.
• Use a soft lens cloth to clean the MC65. If the surface of the MC65 screen becomes soiled, clean it with
a soft cloth moistened with a diluted window-cleaning solution.
• Periodically replace the rechargeable battery to ensure maximum battery life and product performance.
Battery life depends on individual usage patterns.
6-2
MC65 Integrator Guide
• A screen protector is applied to the MC65. Motorola recommends using this to minimize wear and tear.
Screen protectors enhance the usability and durability of touch screen displays. Benefits include:
• Protection from scratches and gouges
• Durable writing and touch surface with tactile feel
• Abrasion and chemical resistance
• Glare reduction
• Keeping the device’s screen looking new
• Quick and easy installation.
Removing the Screen Protector
A screen protector is applied to the MC65. Motorola recommends using this to minimize wear and tear. Screen
protectors enhance the usability and durability of touch screen displays.
To remove the screen protector, lift the corner using a thin plastic card, such as a credit card, then carefully lift
it off the display.
Lift Screen
Protector
Corner
Figure 6-1 Removing the Screen Protector
CAUTION
Do not use a sharp object to remove the protector. Doing so can damage the display.
NOTE Not using a screen protector can affect warranty coverage. To purchase replacement protectors, contact
your local account manager or Motorola, Inc. These include screen protector installation instructions.
Part number: KT-129195-03R Screen Protector 3/pk.
Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and combustible materials or
chemicals. Particular care should be taken where the device is charged in a non commercial
environment.
• Follow battery usage, storage, and charging guidelines found in this guide.
• Improper battery use may result in a fire, explosion, or other hazard.
Maintenance & Troubleshooting
6-3
• To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF and
+104 ºF (0 ºC and +40 ºC)
• Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a
risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a
battery or a charger, contact Motorola Solutions Global Support.
• For devices that utilize a USB port as a charging source, the device shall only be connected to products
that bear the USB-IF logo or have completed the USB-IF compliance program.
• To enable authentication of an approved battery, as required by IEEE1725 clause 10.2.1, all batteries will
carry a Motorola hologram. Do not fit any battery without checking it has the Motorola authentication
hologram.
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to
overheat.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to
water or other liquids, or expose to fire, explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle
or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to properly dispose of used re-chargeable batteries.
• Do not dispose of batteries in fire.
• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact
has been made, wash the affected area with large amounts of water and seek medical advice.
• If you suspect damage to your equipment or battery, contact Motorola Solutions Global Customer
Support to arrange for inspection.
Cleaning
CAUTION
Always wear eye protection.
Read warning label on compressed air and alcohol product before using.
If you have to use any other solution for medical reasons please contact Motorola for more
information.
WARNING! Avoid exposing this product to contact with hot oil or other flammable liquids. If such
exposure occurs, unplug the device and clean the product immediately in accordance with
these guidelines.
Materials Required
• Alcohol wipes
• Lens tissue
• Cotton tipped applicators
6-4
MC65 Integrator Guide
• Isopropyl alcohol
• Can of compressed air with a tube.
Cleaning the MC65
Housing
Using the alcohol wipes, wipe the housing including keys and in-between keys.
Display
The display can be wiped down with the alcohol wipes, but care should be taken not to allow any pooling of
liquid around the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent
streaking.
Scanner Exit Window
Wipe the scanner exit window periodically with a lens tissue or other material suitable for cleaning optical
material such as eyeglasses.
Connector
1.
Remove the main battery from mobile computer. See Installing the Battery on page 1-4.
2.
Dip the cotton portion of the cotton tipped applicator in isopropyl alcohol.
3.
Rub the cotton portion of the cotton tipped applicator back-and-forth across the connector on the bottom of
the MC65. Do not leave any cotton residue on the connector.
4.
Repeat at least three times.
5.
Use the cotton tipped applicator dipped in alcohol to remove any grease and dirt near the connector area.
6.
Use a dry cotton tipped applicator and repeat steps 4 through 6.
7.
Spray compressed air on the connector area by pointing the tube/nozzle about ½ inch away from the
surface.
CAUTION
8.
Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face.
Inspect the area for any grease or dirt, repeat if required.
Cleaning Cradle Connectors
To clean the connectors on a cradle:
1.
Remove the DC power cable from the cradle.
2.
Dip the cotton portion of the cotton tipped applicator in isopropyl alcohol.
3.
Rub the cotton portion of the cotton tipped applicator along the pins of the connector. Slowly move the
applicator back-and-forth from one side of the connector to the other. Do not let any cotton residue on the
connector.
4.
All sides of the connector should also be rubbed with the cotton tipped applicator.
Maintenance & Troubleshooting
5.
6-5
Spray compressed air in the connector area by pointing the tube/nozzle about ½ inch away from the
surface.
CAUTION
Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face.
6.
Ensure that there is no lint left by the cotton tipped applicator, remove lint if found.
7.
If grease and other dirt can be found on other areas of the cradle, use lint free cloth and alcohol to remove.
8.
Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry
before applying power to cradle.
If the temperature is low and humidity is high, longer drying time is required. Warm temperature and dry
humidity requires less drying time.
Cleaning Frequency
The cleaning frequency is up to the customer’s discretion due to the varied environments in which the mobile
devices are used. They may be cleaned as frequently as required. However when used in dirty environments it
may be advisable to periodically clean the scanner exit window to ensure optimum scanning performance.
Troubleshooting
MC65
Table 6-1 Troubleshooting the MC65
Problem
When pressing the
power button the MC65
does not turn on.
Cause
Solution
Battery not charged.
Charge or replace the battery in the MC65.
Battery not installed
properly.
Install the battery properly. See Installing the Battery on page 1-4.
System crash.
Perform a reset. See Resetting the MC65 on page 1-8.
When pressing the
power button the MC65
does not turn on but two
LEDs blink.
Battery charge is at a
level where data is
maintained but
battery should be
re-charged.
Charge or replace the battery in the MC65.
Rechargeable battery
did not charge.
Battery failed.
Replace battery. If the MC65 still does not operate, perform a reset.
See Resetting the MC65 on page 1-8.
MC65 removed from
cradle while battery
was charging.
Insert MC65 in cradle. The 3600 mAh battery fully charges in less
than six hours.
Extreme battery
temperature.
Battery does not charge if ambient temperature is below 0°C (32°F)
or above 40°C (104°F).
MC65 not powered
on.
Press the Power button.
Cannot see characters
on display.
6-6
MC65 Integrator Guide
Table 6-1 Troubleshooting the MC65 (Continued)
Problem
Cause
Solution
During data
communication, no data
transmitted, or
transmitted data was
incomplete.
MC65 removed from
cradle or
disconnected from
host computer during
communication.
Replace the MC65 in the cradle, or reattach the communication cable
and re-transmit.
Incorrect cable
configuration.
See the system administrator.
Communication
software was
incorrectly installed or
configured.
Perform setup. Refer to the MC65 Integrator Guide for details.
No sound.
Volume setting is low
or turned off.
Adjust the volume.
MC65 shuts off.
MC65 is inactive.
The MC65 turns off after a period of inactivity. If the MC65 is running
on battery power, set this period from 1 to 5 minutes, in one-minute
intervals.
Check the Power window by selecting Tap Status Bar >
.
Battery is depleted.
Replace the battery.
Battery is not inserted
properly.
Insert the battery properly. See Installing the Battery on page 1-4.
Screen is not
calibrated correctly.
Re-calibrate the screen. Press Blue key - Backspace key.
The device is not
responding.
Reset the device. See Resetting the MC65 on page 1-8.
Too many files stored
on the MC65.
Delete unused memos and records. If necessary, save these records
on the host computer (or use an SD card for additional memory).
Too many
applications installed
on the MC65.
Remove user-installed applications on the MC65 to recover memory.
Select Start > Settings > System and tap the Remove Programs
icon. Select the unused program and tap Remove.
The Charging/Battery
Status LED flashes with
the Power button is
pressed and the MC65
does not turn on.
The MC65’s battery is
low.
Recharge the battery.
Camera application does
not launch.
DataWedge
application running.
Stop DataWedge application. Tap Start > Settings > System > Task
Manager. Select DataWedge application and tap End Task.
Tapping the window
buttons or icons does not
activate the
corresponding feature.
A message appears
stating that the MC65
memory is full.
Maintenance & Troubleshooting
6-7
Table 6-1 Troubleshooting the MC65 (Continued)
Problem
Cause
Solution
The MC65 does not
decode with reading bar
code.
Scanning application
is not loaded.
Load a scanning application on the MC65. See your system
administrator.
Unreadable bar code.
Ensure the symbol is not defaced.
Distance between exit
window and bar code
is incorrect.
Place the MC65 within proper scanning range.
MC65 is not
programmed for the
bar code.
Program the MC65 to accept the type of bar code being scanned.
Refer to the EMDK or Control Panel application.
MC65 is not
programmed to
generate a beep.
If the MC65 does not beep on a good decode, set the application to
generate a beep on good decode.
Battery is low.
If the scanner stops emitting a laser beam upon a trigger press, check
the battery level. When the battery is low, the scanner shuts off before
the MC65 low battery condition notification.
Note: If the scanner is still not reading symbols, contact the distributor
or Motorola.
Bluetooth Connection
Table 6-2 Troubleshooting Bluetooth Connection
Problem
MC65 cannot find any
Bluetooth devices
nearby.
Cause
Solution
Too far from other
Bluetooth devices.
Move closer to the other Bluetooth device(s), within a range of 10
meters (32.8 feet).
The Bluetooth
device(s) nearby are
not turned on.
Turn on the Bluetooth device(s) to find.
The Bluetooth
device(s) are not in
discoverable mode.
Set the Bluetooth device(s) to discoverable mode. If needed, refer to
the device’s user documentation for help.
Single Slot USB Cradle
Table 6-3 Troubleshooting the Single Slot USB Cradle
Symptom
Possible Cause
Action
LEDs do not light when
MC65 or spare battery is
inserted.
Cradle is not receiving
power.
Ensure the power cable is connected securely to both the cradle and
to AC power.
MC65 is not seated
firmly in the cradle.
Remove and re-insert the MC65 into the cradle, ensuring it is firmly
seated.
Spare battery is not
seated firmly in the
cradle.
Remove and re-insert the spare battery into the charging slot,
ensuring it is firmly seated.
6-8
MC65 Integrator Guide
Table 6-3 Troubleshooting the Single Slot USB Cradle (Continued)
Symptom
MC65 battery is not
charging.
Spare battery is not
charging.
During data
communication, no data
transmits, or transmitted
data was incomplete.
Possible Cause
Action
MC65 was removed
from cradle or cradle
was unplugged from
AC power too soon.
Ensure cradle is receiving power. Ensure MC65 is seated correctly.
Confirm main battery is charging under Tap Status Bar >
3600 mAh battery fully charges in less than six hours.
. The
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty
battery.
The MC65 is not fully
seated in the cradle.
Remove and re-insert the MC65 into the cradle, ensuring it is firmly
seated.
Extreme battery
temperature.
Battery does not charge if ambient temperature is below 0°C (32°F)
or above 40°C (104°F).
Battery not fully
seated in charging
slot.
Remove and re-insert the spare battery in the cradle, ensuring it is
firmly seated.
Battery inserted
incorrectly.
Re-insert the battery so the charging contacts on the battery align
with the contacts on the cradle.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty
battery.
MC65 removed from
cradle during
communications.
Replace MC65 in cradle and retransmit.
Communication
software is not
installed or configured
properly.
Perform setup as described in Single Slot USB Cradle on page 2-3.
Four Slot Ethernet Cradle
Table 6-4 Troubleshooting the Four Slot Ethernet Cradle
Symptom
During
communication, no
data transmits, or
transmitted data was
incomplete.
Cause
Solution
MC65 removed
from cradle during
communications.
Replace MC65 in cradle and retransmit.
MC65 has no active
connection.
An icon is visible in the status bar if a connection is currently
active.
Maintenance & Troubleshooting
6-9
Table 6-4 Troubleshooting the Four Slot Ethernet Cradle (Continued)
Symptom
Battery is not
charging.
Cause
MC65 removed
from the cradle too
soon.
Solution
Replace the MC65 in the cradle. The 3600 mAh battery fully
charges in less than six hours. Tap Status Bar >
battery status.
to view
Battery is faulty.
Verify that other batteries charge properly. If so, replace the
faulty battery.
MC65 is not
inserted correctly in
the cradle.
Remove the MC65 and reinsert it correctly. Verify charging is
Ambient
temperature of the
cradle is too warm.
Move the cradle to an area where the ambient temperature is
between 0°C (32°F) and 35°C (95°F).
active. Tap Status Bar >
to view battery status.
Vehicle Cradle
Table 6-5 Troubleshooting the Vehicle Cradle
Symptom
Possible Cause
Action
MC65 battery charging
LED does not light up.
Cradle is not receiving
power.
Ensure the power input cable is securely connected to the cradle’s
power port.
MC65 battery is not
recharging.
MC65 was removed
from the cradle too
soon.
Replace the MC65 in the cradle. The 3600 mAh battery fully charges
in less than six hours.
Battery is faulty.
Replace the battery.
MC65 is not placed
correctly in the cradle.
Remove the MC65 from the cradle, and re-insert correctly. If the
battery still does not charge, contact customer support.
The MC65 battery charging LED slowly blinks amber when the MC65
is correctly inserted and charging.
Ambient temperature
of the cradle is too
warm.
Move to an area where the ambient temperature is between 0°C and
40°C (32°F and 104°F).
Four Slot Battery Charger
r
Table 6-6 Troubleshooting The Four Slot Battery Charger
Symptom
Battery not charging.
Possible Cause
Action
Battery was removed
from the charger or
charger was
unplugged from AC
power too soon.
Re-insert the battery in the charger or re-connect the charger’s power
supply. The 3600 mAh battery fully charges in less than six hours.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty
battery.
Battery contacts not
connected to charger.
Verify that the battery is seated in the battery well correctly with the
contacts facing down.
6 - 10 MC65 Integrator Guide
Cables
Table 6-7 Troubleshooting the Cables
Symptom
MC65 battery is not
charging.
During data
communication, no data
transmits, or transmitted
data was incomplete.
Possible Cause
MC65 was
disconnected from
AC power too soon.
Action
Connect the power cable correctly. Confirm main battery is charging
under Tap Status Bar >
less than six hours.
. The 3600 mAh battery fully charges in
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty
battery.
The MC65 is not fully
attached to power.
Detach and re-attach the power cable to the MC65, ensuring it is
firmly connected.
Cable was
disconnected from
MC65 during
communications.
Re-attach the cable and retransmit.
Incorrect cable
configuration.
See the system administrator.
Communication
software is not
installed or configured
properly.
Perform setup as described in Cables on page 2-25.
Magnetic Stripe Reader
Table 6-8 Troubleshooting the Magnetic Stripe Reader
Symptom
MSR cannot read card.
MC65 battery is not
charging.
Possible Cause
Action
MSR removed from
MC65 during card
swipe.
Reattach MSR to MC65 and reswipe the card.
Faulty magnetic stripe
on card.
See the system administrator.
MSR application is
not installed or
configured properly.
Ensure the MSR application is installed on the MC65.
Ensure the MSR application is configured correctly.
MC65 was removed
from MSR or MSR
was unplugged from
AC power too soon.
Ensure MSR is receiving power. Ensure MC65 is attached correctly.
Confirm main battery is charging under Start > Settings > System >
Power. The 3600 mAh battery fully charges in less than six hours.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty
battery.
The MC65 is not fully
attached to the MSR.
Detach and re-attach the MSR to the MC65, ensuring it is firmly
connected.
Maintenance & Troubleshooting 6 - 11
Table 6-8 Troubleshooting the Magnetic Stripe Reader (Continued)
Symptom
Possible Cause
Action
During data
communication, no data
transmits, or transmitted
data was incomplete.
MC65 detached from
MSR during
communications.
Reattach MC65 to MSR and retransmit.
Incorrect cable
configuration.
See the system administrator.
Communication
software is not
installed or configured
properly.
Perform setup as described in the MC65 Integrator Guide.
6 - 12 MC65 Integrator Guide
APPENDIX A TECHNICAL SPECIFICATIONS
MC65 Technical Specifications
The following tables summarize the EDA’s intended operating environment and technical hardware
specifications.
MC65
Table A-1 MC65 EDA Technical Specifications
Item
Description
Physical Characteristics
Dimensions
Height: 1.2 cm (6. in.)
Width: 7.7 cm (3.03 in.)
Depth: 3. cm (1. in.)
Weight
359 g (12.5 oz.)
Display
Color 3.5” VGA with backlight, 65K colors, 480 x 640
Touch Panel
Glass analog resistive touch
Backlight
LED backlight
Battery Pack
Rechargeable Lithium Ion 3.7V, 3600 mAh battery
Expansion Slot
microSD slot (supports up to 32 GB).
Connection Interface
USB 2.0 High Speed (host and client)
Notification
Audible tone plus multi-color LEDs
Keypad Options
numeric, QWERTY, AZERTY, QWERTZ, DSD or PIM
Audio
Dual microphone support with noise cancellation; vibrate alert; speaker;
Bluetooth headset
A-2
MC65 Integrator Guide
Table A-1 MC65 EDA Technical Specifications (Continued)
Item
Description
Performance Characteristics
CPU
MSM Qualcomm 7627@ 600 MHz (multi-processor architecture)
Operating System
Microsoft® Windows Mobile™ 6.5 Professional
Memory
256 MB RAM/1 GB Flash or 512 MB RAM/1 GB Flash
Output Power
USB: 5VDC @ 300 mA max.
User Environment
Operating Temperature
-10°C to 50°C (14°F to 122°F)
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Charging Temperature
32°F to 104°F
Humidity
5 to 95% non-condensing
Drop Specification
Multiple 6 ft. drops per MIL-STD 810G specifications
Multiple 5 ft. drops to concrete at room temperature
Multiple 4 ft. drops to concrete across the operating temperature range
Tumble
1,000 1.6 ft. tumbles at room temperature; per applicable IEC tumble
specifications
Electrostatic Discharge (ESD)
+/-15kVdc air discharge, +/-8kVdc direct discharge, +/-8kVdc indirect
discharge
Sealing
IP64; per applicable IEC sealing specifications
Vibration
4g’s PK Sine (5Hz to 2KHz); 0.04g2/Hz Random (20Hz to 2KHz); 60 minute
duration per axis, 3 axis
Thermal Shock
-40° C to 70° C (-40° F to 158° F) rapid transition
Battery Performance
Standby Time
100 hours
Talk Time
6 hours
User Profiles
8 hours
Motorola Interactive Sensor Technology (IST)
Motion Sensor
3-axis accelerometer that enables motion-sensing applications for dynamic
screen orientation and power management.
Light Sensor
Ambient light sensor to auto adjust display brightness.
Wireless WAN Data and Voice Communications
Radio
Dual 3.5G: GSM HSPA/HSUPA and CDMA EVDO Rev A
Frequency Band
UMTS/HSDPA and HSUPA: 850, 1900 and 2100 MHz
GSM/EDGE: 850, 900, 1800 and 1900 MHz
CDMA/EVDO Rev A: 850 and 1900 MHz
Technical Specifications
A-3
Table A-1 MC65 EDA Technical Specifications (Continued)
Item
Description
Wireless LAN Data and Voice Communications
Radio
Tri-mode IEEE® 802.11a/b/g
Data Rates Supported
1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps
Operating Channels
Chan 36-165 (5180 – 5825 MHz)
Chan 1-13 (2412-2472 MHz)
Chan 14 (2484 MHz) Japan only
Actual operating channels/frequencies depend on regulatory rules and
certification agency
Security
WPA2 (Personal or Enterprise); 802.1x; EAP-TLS; TTLS (CHAP, MS-CHAP,
MS-CHAPv2, PAP or MD5); PEAP (TLS, MSCHAPv2, EAP-GTC); LEAP,
EAP-FAST (TLS, MS-CHAPv2, EAP-GTC)
Voice Communications
Voice-over-IP ready, Wi-Fi™-certified, IEEE 802.11a/b/g direct sequence
wireless LAN, Wi-Fi ™ (WMM and WMM-PS) Motorola Voice Quality
Manager (VQM), Motorola TEAM Express Ready
Wireless PAN Data and Voice Communications
Bluetooth
Class II, v2. with Enhanced Data Rate (EDR)
Global Positioning System
GPS
Integrated stand-alone or Assisted-GPS (A-GPS).
Data Capture Specifications
Options
2D imager and color camera
2D Imager Engine (SE4500-SR) Specifications
Field of View
Horizontal - 39.6°
Vertical - 25.7°
Optical Resolution
WVGA 752 H x 480 V pixels (gray scale)
Roll
360°
Pitch Angle
+/- 60° from normal
Skew Tolerance
+/- 60° from normal
Ambient Light
Indoor: 450 ft. candles (4845 lux)
Outdoor: 9000 ft. candles (96,900 lux)
Sunlight: 8000 ft. candles
Fluorescent: 450 ft. candles
Focal Distance
From center of exit window: 19 cm (7.5 in.)
Aiming Element (VLD)
655 nm +/- 10 nm
Illumination Element (LED)
625 nm +/- 5 nm
A-4
MC65 Integrator Guide
Table A-1 MC65 EDA Technical Specifications (Continued)
Item
Description
2D Imager Engine (SE4500-DL) Specifications
Field of View
Horizontal - 39.2°
Vertical - 25.4°
Optical Resolution
752 H x 480 V pixels (gray scale)
Roll
360°
Pitch Angle
+/- 60° from normal
Skew Tolerance
+/- 60° from normal
Ambient Light
Indoor: 450 ft. candles (4845 lux)
Outdoor: 9000 ft. candles (96,900 lux)
Sunlight: 8000 ft. candles
Fluorescent: 450 ft. candles
Focal Distance
From center of the exit window: 18.5 cm (7.3 in.)
Aiming Element (VLD)
655 nm +/- 10 nm
Illumination Element (LED)
625 nm +/- 5 nm LEDs (2x)
Camera Specifications
Resolution
3.2 Mega pixel
Technical Specifications
A-5
Table A-2 Data Capture Options
Item
Description
Imaging Decode Capability
Code 39
Code 128
Code 93
Codabar
Code 11
Interleaved 2 of 5
Discrete 2 of 5
MSI
EAN-8
EAN-13
UPCA
UPCE
UPC/EAN supplementals Coupon Code
Trioptic 39
Webcode
TLC39
Composite AB
Composite C
Micro PDF-417
PDF-417
Macro PDF-417
(Macro) Micro PDF-417 QR Code
Data Matrix
Maxi Code
US Postnet
US Planet
UK 4-state
Australian 4-state
Canadian 4-state
Japanese 4-state
Dutch Kix
Chinese 2 of 5
USPS 4-state (US4CB) Aztec
microQR
GS1 DataBar
GS1 DataBar Truncated
GS1 DataBar Limited
GS1 DataBar Stacked
GS1 DataBar Expanded GS1 DataBar Expanded Stacked
GS1 DataBar Stacked Omni
Camera Decode Capability
Code 39
Code 128
Codabar
Code 11
Discrete 2 of 5
MSI
EAN-13
UPCA
UPC/EAN supplementals Coupon Code
Webcode
TLC39
Composite C
Micro PDF-417
Macro PDF-417
(Macro) Micro PDF-417
Data Matrix
Maxi Code
US Planet
UK 4-state
Canadian 4-state
Japanese 4-state
GS1 DataBar
GS1 DataBar Truncated
GS1 DataBar Stacked
GS1 DataBar Expanded
GS1 DataBar Expanded Stacked
Code 93
Interleaved 2 of 5
EAN-8
UPCE
Trioptic 39
Composite AB
PDF-417
QR Code
US Postnet
Australian 4-state
Dutch Kix
GS1 DataBar Limited
GS1 DataBar Stacked Omni
A-6
MC65 Integrator Guide
Decode Zones
SE4500-SR
Figure A-1 shows the decode zone for the SE4500-SR. Typical values appear. Table A-3 lists the typical
distances for selected bar code densities. The minimum element width (or “symbol density”) is the width in mils
of the narrowest element (bar or space) in the symbol.
Note: Typical performance at 73˚F (23˚C)
on high quality symbols in normal room light.
Vcc = 3.3V
in.
cm
9
22.9
4.5 11.4
0
4.5 11.4
5 mil Code 39
7.5
2.1
6.67 mil PDF417
7.1
3.4
7.5 mil Code 39
*
1.6
9
10.6
10 mil PDF417
*
10.1
13 mil (100% UPC)
15.5
15 mil PDF417
*
2.8
15 mil Data Matrix
14.7
12.4
20 mil Code 39
24.7
*
In.
cm
0
0
5
12.7
0
10
25.4
15
38.1
20
50.8
25
63.5
Depth of Field
* Minimum distance determined by symbol length and scan angle.
Figure A-1 SE4500-SR Decode Zone
22.9
W
i
d
t
h
o
f
F
i
e
l
d
Technical Specifications
Table A-3
SE4500-SR Decode Distances
Symbol Density/
Bar Code Type
Typical Working Ranges
Bar Code Content/
ContrastNote 2
Near
Far
5.0 mil
Code 39
ABCDEFGH
80% MRD
2.1 in
5.33 cm
7.5 in
19.05 cm
6.67 mil
PDF417
4 Col, 20 Rows
80% MRD
3.4 in
8.64 cm
7.1 in
18.03 cm
7.5 mil
Code 39
ABCDEF
80% MRD
Note 1
10.6 in
26.92 cm
10 mil
PDF417
3 Col, 17 Rows
80% MRD
Note 1
10.1 in
25.65 cm
13 mil
UPC-A
012345678905
80% MRD
1.6 in
5.08 cm
15.5 in
39.37 cm
15 mil
PDF417
80% MRD
Note 1
14.7 in
37.34 cm
15 mil
Data Matrix
18 x 18 Modules
80% MRD
2.8 in
7.11 cm
12.4 in
31.50 cm
20 mil
Code 39
123
80% MRD
Note 1
24.7 in
62.74 cm
Notes:
1. Near distances are field-of-view (FOV) limited.
2. Contrast is measured as Mean Reflective Difference (MRD) at 670 nm.
3. Working range specifications at temperature = 23°C, pitch=18°, roll=0°, skew=0°, photographic quality,
ambient light ~30 ft-c, humidity 45-70% RH.
4. Distances measured from front edge of scan engine chassis.
A-7
A-8
MC65 Integrator Guide
SE4500-DL
Figure A-2 shows the decode zone for the SE4500-DL. Typical values appear. Table A-4 lists the typical
distances for selected bar code densities. The minimum element width (or “symbol density”) is the width in mils
of the narrowest element (bar or space) in the symbol.
Note: Typical performance at 73˚F (23˚C)
on high quality symbols in normal room light.
Vcc = 3.3V
3 mil Code 39
4.2
2.7
5 mil Code 39
1.4
7.3
5 mil PDF417
4.5
2.8
1.9
6.67 mil PDF417
6.9
7.5 mil Code 39
*
9.9
10 mil PDF417
*
9.0
13 mil (100% UPC)
1.6
15 mil PDF417
*
2.3
15 mil Data Matrix
12
11.7
11.2
20 mil Code 39
19.7
*
In.
cm
0
0
4
10.2
8
20.3
12
30.5
16
40.6
20
50.8
Depth of Field
* Minimum distance determined by symbol length and scan angle.
Figure A-2 SE4500-DL Decode Zone
in.
cm
8
20.3
4
10.2
0
0
4
10.2
8
20.3
W
i
d
t
h
o
f
F
i
e
l
d
Technical Specifications
Table A-4
SE4500-DL Decode Distances
Symbol Density/
Bar Code Type
Typical Working Ranges
Bar Code Content/
ContrastNote 2
Near
Far
3.0 mil
Code 39
80% MRD
2.7 in
6.86 cm
4.2 in
10.67 cm
5.0 mil
Code 39
ABCDEFGH
80% MRD
1.4 in
3.56 cm
7.3 in
18.54 cm
5.0 mil
PDF417
80% MRD
2.8 in
7.11 cm
4.5 in
11.43 cm
6.67 mil
PDF417
4 Col, 20 Rows
80% MRD
1.9 in
4.83 cm
6.9 in
17.53 cm
7.5 mil
Code 39
ABCDEF
80% MRD
Note 1
9.9 in
25.15 cm
10 mil
PDF417
3 Col, 17 Rows
80% MRD
Note 1
9.0 in
22.86 cm
13 mil
UPC-A
012345678905
80% MRD
1.6 in
5.08 cm
12.0 in
30.48 cm
15 mil
PDF417
80% MRD
Note 1
11.7 in
29.72 cm
15 mil
Data Matrix
18 x 18 Modules
80% MRD
2.3 in
5.84 cm
11.2 in
28.45 cm
20 mil
Code 39
123
80% MRD
Note 1
19.7 in
50.04 cm
Notes:
1. Near distances are FOV limited.
2. Contrast is measured as Mean Reflective Difference (MRD) at 670 nm.
3. Working range specifications at temperature = 23°C, pitch=18°, roll=0°, skew=0°, photographic quality,
ambient light ~30 ft-c, humidity 45-70%RH.
4. Distances measured from front edge of scan engine chassis.
A-9
A - 10 MC65 Integrator Guide
MC65 External Connector Pin-Outs
Pin 1
Figure A-3 External Connector
Table A-5 External Connector Pin-Outs
Pin
Description
1
External Trigger/Cradle Detect
2
USB_ID
3
5.4 VDC
4
USB_VCC
5
USB_D-
6
USB_D+
7
Ground
Technical Specifications A - 11
MC65 Accessory Specifications
Single Slot USB Cradle
Table A-6 Single Slot USB Cradle Technical Specifications
Feature
Description
Dimensions
Height: 7.1 cm (2.80 in.)
Width: 11.0 cm (4.33 in.)
Depth: 15.0 cm (5.91 in.)
Weight
210 g (7.41 oz)
Input Voltage
12 VDC
Power Consumption
30 watts
Interface
USB
Operating Temperature
0°C to 50°C (32°F to 122°F)
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Charging Temperature
0°C to 40°C (32°F to 104°F)
Humidity
5% to 95% non-condensing
Drop
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
Four Slot Battery Charger
Table A-7 Four Slot Battery Charger Technical Specifications
Feature
Description
Dimensions
Height: 4.7 cm (1.85 in.)
Width: 15.5 cm (6.10 in.)
Depth: 21.0 cm (8.27 in.)
Weight
384 g (13.55 oz)
Input Voltage
12 VDC
Power Consumption
30 watts
Operating Temperature
0°C to 40°C (32°F to 104°F)
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Charging Temperature
0°C to 40°C (32°F to 104°F)
A - 12 MC65 Integrator Guide
Table A-7 Four Slot Battery Charger Technical Specifications (Continued)
Feature
Description
Humidity
5% to 95% non-condensing
Drop
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
Four Slot Charge Only Cradle
Table A-8 Four Slot Charge Only Cradle Technical Specifications
Feature
Description
Dimensions
Height: 13.7 cm (5.39 in.)
Width: 46.8 cm (18.43 in.)
Depth: 9.9 cm (3.90 in.)
Weight
1115 g (39.33 oz)
Input Voltage
12 VDC
Power Consumption
100 watts
Operating Temperature
0°C to 50°C (32°F to 122°F)
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Charging Temperature
0°C to 40°C (32°F to 104°F)
Humidity
5% to 95% non-condensing
Drop
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
Four Slot Ethernet Cradle
Table A-9 Four Slot Ethernet Cradle Technical Specifications
Feature
Description
Dimensions
Height: 13.7 cm (5.39 in.)
Width: 46.8 cm (18.43 in.)
Depth: 9.9 cm (3.90 in.)
Weight
1115 g (39.33 oz)
Power
12 VDC
Operating Temperature
0°C to 50°C (32°F to 122°F)
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Technical Specifications A - 13
Table A-9 Four Slot Ethernet Cradle Technical Specifications (Continued)
Feature
Description
Charging Temperature
0°C to 40°C (32°F to 104°F)
Humidity
5% to 95% non-condensing
Drop
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
Magstripe Reader
Table A-10 Magstripe Reader (MSR) Technical Specifications
Feature
Description
Dimensions
8.4 cm x 9.4 cm (3.3 in. x 3.7 in.)
Weight
79.4 g (2.8 oz)
Interface
Serial with baud rate up to 19,200
Format
ANSI, ISO, AAMVA, CA DMV, user-configurable generic format
Swipe Speed
5 to 50 in. (127 to 1270 mm) /sec, bi-directional
Decoders
Generic, Raw Data
Mode
Buffered, unbuffered
Track Reading Capabilities
Tracks 1 and 3: 210 bpi
Track 2: 75 and 210 bpi, autodetect
Operating Temperature
32° to 122° F (0° to 50° C)
Storage Temperature
-40° to 158° F (-40° to 70° C)
Humidity
5% to 95% non-condensing
Drop
4 ft. (1.22 m) drops to concrete
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
A - 14 MC65 Integrator Guide
Vehicle Cradle
Table A-11 Vehicle Cradle Technical Specifications
Feature
Description
Dimensions
Height: 10.4 cm (4.09 in.)
Width: 11.1 cm (4.37 in.)
Depth: 6.9 cm (2.72 in.)
Weight
240 g (8.47 oz)
Power
9- 32 VDC
Operating Temperature
-20°C to 50°C (-4°F to 122°F)
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Charging Temperature
0°C to 40°C (32°C to 104°F)
Humidity
10% to 95% non-condensing
Drop
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
Cables
Table A-12 USB Charging Cable Technical Specifications
Feature
Description
Length
161.9 cm (63.74 in.)
Operating Temperature
-10°C to 50°C (14°F to 122°F)
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Humidity
10% to 95% non-condensing
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
Table A-13 Charge Only Cable Technical Specifications
Feature
Description
Length
28.0 cm (11.00 in.)
Operating Temperature
-10°C to 50°C (14°F to 122°F)
Technical Specifications A - 15
Table A-13 Charge Only Cable Technical Specifications (Continued)
Feature
Description
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Humidity
10% to 95% non-condensing
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
Table A-14 Auto Charge Cable Technical Specifications
Feature
Description
Length
169.0 cm (66.54 in.)
Input Voltage
12 - 24 VDC
Operating Temperature
-10°C to 50°C (14°F to 122°F)
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Humidity
10% to 95% non-condensing
Electrostatic Discharge (ESD)
+/- 15 kV air
+/- 8 kV contact
A - 16 MC65 Integrator Guide
APPENDIX B SOFTWARE
SMS8 Configuration
To set the primary local language for SMS messages:
Using a registry editor, navigate to the following:
[HKEY_LOCAL_MACHINE\Comm\Cellular\RIL\SMS\NLTables]
Edit the following key:
“LocalePrimaryLangauge” = dword:1
where:
dword:0 = None
dword:1 = Turkish
dword:2 = Spanish
dword:3 = Portuguese
Cache Disk Configuration
To enable or disable the use of cache disk:
Using a registry editor, navigate to the following:
[HKEY_LOCAL_MACHINE\Drivers\Builtin\RAMDisk]
Edit the following key:
“Size” = dword:4194304
where:
dword:0 = Cache disk size is 0.
dword:4194304 = Cache disk size is 4,194,304 bytes (4 MB)
B-2
MC65 User Guide
Auto Reboot
To warm boot the MC65 in case of an ARM9 lockup.
Using a registry editor, navigate to the following:
[HKEY_LOCAL_MACHINE\Software\Motorola\AutoReboot]
Edit the following key:
“Enable” = dword:1
where:
dword:0 = disabled.
dword:1 = enabled (default).
NOTE The absence of a value shall default to “Enabled.”
Daily Reboot
To warm boot the MC65 at a specified time of day.
Using a registry editor, navigate to the following:
[HKEY_LOCAL_MACHINE\Software\Motorola\dailyReboot]
Edit the following key:
“dailyRebootTime” = XX:XX
where:
XX:XX is a time from 00:00 (12:00 am) to 23:59 in 24 hours time format.
Edit the following key:
“Disable” = dword:1
where:
dword:0 = enabled.
dword:1 = disabled (default).
NOTE If this key is not present then the default is “Disabled.”
SMS Cell Broadcast
To locally enable or disable the Cell Broadcast feature. Cell Broadcast is one-to-many geographically focused
service.
Software
Using a registry editor, navigate to the following:
[HKEY_LOCAL_MACHINE\Software\Motorola\SMS_CB]
Edit the following key:
“Enable” = dword:1
where:
dword:0 = disabled.
dword:1 = enabled (default).
NOTE The absence of a value shall default to “Enabled.”
B-3
B-4
MC65 User Guide
GLOSSARY
A
API. (Application Programming Interface) An interface by means of which one software component communicates with
or controls another. Usually used to refer to services provided by one software component to another, usually via
software interrupts or function calls
AZERTY. A standard keyboard commonly used on French keyboards. “AZERTY” refers to the arrangement of keys on
the top row of keys.
AKU. (Adaptation Kit Update) Updates to the Windows Mobile operating system.
AFH. Adaptive Frequency Hopping
ActiveSync. ActiveSync is a data synchronization program developed by Microsoft for use with Windows Mobile
operating systems.
B
Bar Code. A pattern of variable-width bars and spaces which represents numeric or alphanumeric data in
machine-readable form. The general format of a bar code symbol consists of a leading margin, start character, data
or message character, check character (if any), stop character, and trailing margin. Within this framework, each
recognizable symbology uses its own unique format. See Symbology.
Bit. Binary digit. One bit is the basic unit of binary information. Generally, eight consecutive bits compose one byte of
data. The pattern of 0 and 1 values within the byte determines its meaning.
Bits per Second (bps). Bits transmitted or received.
Bluetooth. A wireless protocol utilizing short-range communications technology facilitating data transmission over short
distances.
boot or boot-up. The process a computer goes through when it starts. During boot-up, the computer can run
self-diagnostic tests and configure hardware and software.
Glossary - 2
MC65 Integrator Guide
bps. See Bits Per Second.
Byte. On an addressable boundary, eight adjacent binary digits (0 and 1) combined in a pattern to represent a specific
character or numeric value. Bits are numbered from the right, 0 through 7, with bit 0 the low-order bit. One byte in
memory is used to store one ASCII character.
C
CDRH. Center for Devices and Radiological Health. A federal agency responsible for regulating laser product safety.
This agency specifies various laser operation classes based on power output during operation.
CDRH Class 1. This is the lowest power CDRH laser classification. This class is considered intrinsically safe, even if all
laser output were directed into the eye's pupil. There are no special operating procedures for this class.
CDRH Class 2. No additional software mechanisms are needed to conform to this limit. Laser operation in this class
poses no danger for unintentional direct human exposure.
Character. A pattern of bars and spaces which either directly represents data or indicates a control function, such as a
number, letter, punctuation mark, or communications control contained in a message.
Codabar. A discrete self-checking code with a character set consisting of digits 0 to 9 and six additional characters: (“-”,
“$”, “:”, “/”, “,” and “+”).
Code 128. A high density symbology which allows the controller to encode all 128 ASCII characters without adding extra
symbol elements.
Code 3 of 9 (Code 39). A versatile and widely used alphanumeric bar code symbology with a set of 43 character types,
including all uppercase letters, numerals from 0 to 9 and 7 special characters (“-”, “.”, “/”, “+”, “%”, “$” and space).
The code name is derived from the fact that 3 of 9 elements representing a character are wide, while the remaining
6 are narrow.
Code 93. An industrial symbology compatible with Code 39 but offering a full character ASCII set and a higher coding
density than Code 39.
COM port. Communication port; ports are identified by number, e.g., COM1, COM2.
Cradle. A cradle is used for charging the terminal battery and for communicating with a host computer, and provides a
storage place for the terminal when not in use.
D
DCP. See Device Configuration Package.
Decode. To recognize a bar code symbology (e.g., UPC/EAN) and then analyze the content of the specific bar code
scanned.
Decode Algorithm. A decoding scheme that converts pulse widths into data representation of the letters or numbers
encoded within a bar code symbol.
Decryption. Decryption is the decoding and unscrambling of received encrypted data. Also see, Encryption and Key.
Glossary - 3
Depth of Field. The range between minimum and maximum distances at which a scanner can read a symbol with a
certain minimum element width.
Device Configuration Package. The Symbol Device Configuration Package provides the Product Reference Guide
(PRG), flash partitions, Terminal Configuration Manager (TCM) and the associated TCM scripts. With this package
hex images that represent flash partitions can be created and downloaded to the mobile computer.
Discrete 2 of 5. A binary bar code symbology representing each character by a group of five bars, two of which are
wide. The location of wide bars in the group determines which character is encoded; spaces are insignificant. Only
numeric characters (0 to 9) and START/STOP characters may be encoded.
E
EAN. European Article Number. This European/International version of the UPC provides its own coding format and
symbology standards. Element dimensions are specified metrically. EAN is used primarily in retail.
EMDK. Enterprise Mobility Developer’s Kit.
ESD. Electro-Static Discharge
F
File Transfer Protocol (FTP). A TCP/IP application protocol governing file transfer via network or telephone lines. See
TCP/IP.
Flash Memory. Flash memory is nonvolatile, semi-permanent storage that can be electronically erased in the circuit
and reprogrammed.
FHSS (Frequency Hopping Spread). A method of transmitting radio signals by rapidly switching a carrier among many
frequency channels, using a pseudorandom sequence known to both transmitter and receiver.
G
GPS (Global Positioning System). A satellite-based navigation system made up of a network of 24 satellites. GPS
satellites circle the earth and transmit signal information to earth. GPS receivers take this information and use
triangulation to calculate the user's exact location.
H
Hz. Hertz; A unit of frequency equal to one cycle per second.
Host Computer. A computer that serves other terminals in a network, providing such services as computation,
database access, supervisory programs and network control.
Glossary - 4
MC65 Integrator Guide
I
IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various
laser operation classes based on power output during operation.
IEC (825) Class 1. This is the lowest power IEC laser classification. Conformity is ensured through a software restriction
of 120 seconds of laser operation within any 1000 second window and an automatic laser shutdown if the scanner's
oscillating mirror fails.
IEEE Address. See MAC Address.
Input/Output Ports. I/O ports are primarily dedicated to passing information into or out of the terminal’s memory. MC65
mobile computers include USB ports.
Interleaved 2 of 5. A binary bar code symbology representing character pairs in groups of five bars and five
interleaved spaces. Interleaving provides for greater information density. The location of wide elements
(bar/spaces) within each group determines which characters are encoded. This continuous code type uses no
intercharacter spaces. Only numeric (0 to 9) and START / STOP characters may be encoded.
Internet Protocol Address. See IP.
I/O Ports. The connection between two devices, defined by common physical characteristics, signal characteristics, and
signal meanings. Types of interfaces include RS-232 and USB.
IP. Internet Protocol. The IP part of the TCP/IP communications protocol. IP implements the network layer (layer 3) of
the protocol, which contains a network address and is used to route a message to a different network or subnetwork.
IP accepts “packets” from the layer 4 transport protocol (TCP or UDP), adds its own header to it and delivers a
“datagram” to the layer 2 data link protocol. It may also break the packet into fragments to support the maximum
transmission unit (MTU) of the network.
IP Address. (Internet Protocol address) The address of a computer attached to an IP network. Every client and server
station must have a unique IP address. A 32-bit address used by a computer on a IP network. Client workstations
have either a permanent address or one that is dynamically assigned to them each session. IP addresses are written
as four sets of numbers separated by periods; for example, 204.171.64.2.
IPX/SPX. Internet Package Exchange/Sequential Packet Exchange. A communications protocol for Novell. IPX is
Novell’s Layer 3 protocol, similar to XNS and IP, and used in NetWare networks. SPX is Novell's version of the Xerox
SPP protocol.
ISM. Industry Scientific and Medical
K
Key. A key is the specific code used by the algorithm to encrypt or decrypt the data. Also see, Encryption and
Decrypting.
Glossary - 5
L
LASER. Light Amplification by Stimulated Emission of Radiation.The laser is an intense light source. Light from a laser
is all the same frequency, unlike the output of an incandescent bulb. Laser light is typically coherent and has a high
energy density.
laser scanner. A type of bar code reader that uses a beam of laser light.
LCD. See Liquid Crystal Display.
LED Indicator. A semiconductor diode (LED - Light Emitting Diode) used as an indicator, often in digital displays. The
semiconductor uses applied voltage to produce light of a certain frequency determined by the semiconductor's
particular chemical composition.
Light Emitting Diode. See LED.
Liquid Crystal Display (LCD). A display that uses liquid crystal sealed between two glass plates. The crystals are
excited by precise electrical charges, causing them to reflect light outside according to their bias. They use little
electricity and react relatively quickly. They require external light to reflect their information to the user.
M
MC. Mobile Computer.
MDN. Mobile Directory Number. The directory listing telephone number that is dialed (generally using POTS) to reach
a mobile unit. The MDN is usually associated with a MIN in a cellular telephone -- in the US and Canada, the MDN
and MIN are the same value for voice cellular users. International roaming considerations often result in the MDN
being different from the MIN.
MIN. Mobile Identification Number. The unique account number associated with a cellular device. It is broadcast by the
cellular device when accessing the cellular system.
Mobile Computer. In this text, mobile computer refers to the MC65. It can be set up to run as a stand-alone device, or
it can be set up to communicate with a network, using wireless radio technology.
N
Nominal. The exact (or ideal) intended value for a specified parameter. Tolerances are specified as positive and
negative deviations from this value.
NVM. Non-Volatile Memory.
O
Open System Authentication. Open System authentication is a null authentication algorithm.
Glossary - 6
MC65 Integrator Guide
P
PAN . Personal Area Network. Using Bluetooth wireless technology, PANs enable devices to communicate wirelessly.
Generally, a wireless PAN consists of a dynamic group of less than 255 devices that communicate within about a
33-foot range. Only devices within this limited area typically participate in the network.
PING. (Packet Internet Groper) An Internet utility used to determine whether a particular IP address is online. It is used
to test and debug a network by sending out a packet and waiting for a response.
Q
QWERTY. A standard keyboard commonly used on European keyboards. “QWERTY” refers to the arrangement of keys
on the top row of keys.
QWERTZ. A standard keyboard commonly used on German keyboards. “QWERTZ” refers to the arrangement of keys
on the top row of keys.
R
RAM. Random Access Memory. Data in RAM can be accessed in random order, and quickly written and read.
RF. Radio Frequency.
ROM. Read-Only Memory. Data stored in ROM cannot be changed or removed.
Router. A device that connects networks and supports the required protocols for packet filtering. Routers are typically
used to extend the range of cabling and to organize the topology of a network into subnets. See Subnet.
S
Scanner. An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the
bars and spaces of the symbol. Its three main components are: 1) Light source (laser or photoelectric cell) illuminates a bar code,; 2) Photodetector - registers the difference in reflected light (more light reflected from
spaces); 3) Signal conditioning circuit - transforms optical detector output into a digitized bar pattern.
SDK. Software Development Kit
Shared Key. Shared Key authentication is an algorithm where both the AP and the MU share an authentication key.
SID. System Identification code. An identifier issued by the FCC for each market. It is also broadcast by the cellular
carriers to allow cellular devices to distinguish between the home and roaming service.
Space. The lighter element of a bar code formed by the background between bars.
Specular Reflection. The mirror-like direct reflection of light from a surface, which can cause difficulty decoding a bar
code.
Glossary - 7
Start/Stop Character. A pattern of bars and spaces that provides the scanner with start and stop reading instructions
and scanning direction. The start and stop characters are normally to the left and right margins of a horizontal code.
Subnet. A subset of nodes on a network that are serviced by the same router. See Router.
Subnet Mask. A 32-bit number used to separate the network and host sections of an IP address. A custom subnet mask
subdivides an IP network into smaller subsections. The mask is a binary pattern that is matched up with the IP
address to turn part of the host ID address field into a field for subnets. Default is often 255.255.255.0.
Substrate. A foundation material on which a substance or image is placed.
Symbol. A scannable unit that encodes data within the conventions of a certain symbology, usually including start/stop
characters, quiet zones, data characters and check characters.
Symbol Aspect Ratio. The ratio of symbol height to symbol width.
Symbol Height. The distance between the outside edges of the quiet zones of the first row and the last row.
Symbol Length. Length of symbol measured from the beginning of the quiet zone (margin) adjacent to the start
character to the end of the quiet zone (margin) adjacent to a stop character.
Symbology. The structural rules and conventions for representing data within a particular bar code type (e.g. UPC/EAN,
Code 39, PDF417, etc.).
T
TCP/IP. (Transmission Control Protocol/Internet Protocol) A communications protocol used to internetwork dissimilar
systems. This standard is the protocol of the Internet and has become the global standard for communications. TCP
provides transport functions, which ensures that the total amount of bytes sent is received correctly at the other end.
UDP is an alternate transport that does not guarantee delivery. It is widely used for real-time voice and video
transmissions where erroneous packets are not retransmitted. IP provides the routing mechanism. TCP/IP is a
routable protocol, which means that all messages contain not only the address of the destination station, but the
address of a destination network. This allows TCP/IP messages to be sent to multiple networks within an
organization or around the world, hence its use in the worldwide Internet. Every client and server in a TCP/IP
network requires an IP address, which is either permanently assigned or dynamically assigned at startup.
Telnet. A terminal emulation protocol commonly used on the Internet and TCP/IP-based networks. It allows a user at a
terminal or computer to log onto a remote device and run a program.
Terminal. See Mobile Computer.
Terminal Emulation. A “terminal emulation” emulates a character-based mainframe session on a remote
non-mainframe terminal, including all display features, commands and function keys. The VC5000 Series supports
Terminal Emulations in 3270, 5250 and VT220.
TFTP. (Trivial File Transfer Protocol) A version of the TCP/IP FTP (File Transfer Protocol) protocol that has no directory
or password capability. It is the protocol used for upgrading firmware, downloading software and remote booting of
diskless devices.
Tolerance. Allowable deviation from the nominal bar or space width.
Transmission Control Protocol/Internet Protocol. See TCP/IP.
Glossary - 8
MC65 Integrator Guide
Trivial File Transfer Protocol. See TFTP.
U
UDP. User Datagram Protocol. A protocol within the IP protocol suite that is used in place of TCP when a reliable
delivery is not required. For example, UDP is used for real-time audio and video traffic where lost packets are simply
ignored, because there is no time to retransmit. If UDP is used and a reliable delivery is required, packet sequence
checking and error notification must be written into the applications.
UPC. Universal Product Code. A relatively complex numeric symbology. Each character consists of two bars and two
spaces, each of which is any of four widths. The standard symbology for retail food packages in the United States.
V
Visible Laser Diode (VLD). A solid state device which produces visible laser light.
INDEX
A
accessories
auto charge cable . . . . . . . . . . . . . . . . . . . . . . . . 2-1
cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
charge only cable . . . . . . . . . . . . . . . . . . . . . . . . 2-1
EMDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
fabric holster . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
four slot charge only cradle . . . . . . . . . . . . . . . . 2-1
four slot Ethernet cradle . . . . . . . . . . . 2-1, 2-3, 2-10
four slot spare battery charger . . . . . . 2-1, 2-3, 2-23
holster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
MMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
mounting bracket . . . . . . . . . . . . . . . . . . . . . . . 2-16
screen protector . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
single slot USB cradle . . . . . . . . . . . . . . . . . . . . 2-3
spare battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
specifications . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
spring loaded stylus . . . . . . . . . . . . . . . . . . . . . . 2-2
stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
USB charging cable . . . . . . . . . . . . . . . . . . . . . . 2-1
USB cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
vehicle cradle . . . . . . . . . . . . . . . . . . . . . . . 2-1, 2-18
vehicle holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
wall mounting kit, cradle . . . . . . . . . . . . . . . . . . . 2-2
ActiveSync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
deploying CAB files . . . . . . . . . . . . . . . . . . . . . . 4-4
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
setting up a connection . . . . . . . . . . . . . . . . . . . . 3-3
AirBEAM
deploying CAB files . . . . . . . . . . . . . . . . . . . . . . 4-5
APN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
application deployment . . . . . . . . . . . . . . . . . . . . 4-1, 4-4
CAB files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
application folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
application packaging . . . . . . . . . . . . . . . . . . . . . . . . 4-4
application security . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
auto charge cable . . . . . . . . . . . . . . . . . . 2-1, 2-25, 2-26
B
battery
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
battery chargers
four slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
four slot Ethernet cradle . . . . . . . . . . . . . . . . . . 2-13
single slot cradle . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
spare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
vehicle cradle . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
bullets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiii
C
CAB files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4, 4-6
deployment via ActiveSync . . . . . . . . . . . . . . . . . 4-4
deployment via AirBEAM . . . . . . . . . . . . . . . . . . . 4-5
deployment via image update . . . . . . . . . . . . . . . 4-5
deployment via storage card . . . . . . . . . . . . . . . . 4-4
cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
auto charge cable . . . . . . . . . . . . . . . . . . . . . . . . 2-1
pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
cache disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
calibrating the screen . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
call blocking See call barring . . . . . . . . . . . . . . . . . . . 5-8
call forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
call waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
caller id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
changing a PIN for phone use . . . . . . . . . . . . . . . . . . 5-7
charge only cable . . . . . . . . . . . . . . . . . . . . . . . 2-1, 2-25
Index - 2
MC65 Integrator Guide
charge only cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
charging
four slot Ethernet cradle . . . . . . . . . . . . . . . . . . 2-13
single slot cradle . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
spare batteries . . . . . . . . . . . . . . . . . . . . . .1-6, 2-23
vehicle cradle . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
charging temperature . . . . . . . . . . . . . . . . . . . . . . . . 1-6
clean boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
communication/charge cables . . . . . . . . . . . . . . . . . 2-25
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
conventions
notational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
copyfile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
cpf file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
cradles
daisychaining . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Ethernet drivers . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
four slot charge only . . . . . . . . . . . . . . . . . . . . . . 2-1
four slot Ethernet . . . . . . . . . . . . . . . . . 2-1, 2-3, 2-10
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
charging indicators . . . . . . . . . . . . . . . . . . . 2-13
setup . . . . . . . . . . . . . . . . . . . . . . . . . .2-10, 2-15
four slot spare battery charger . . . . . . . . . .2-3, 2-23
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
charging indicators . . . . . . . . . . . . . . . . . . . 2-23
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
mounting bracket . . . . . . . . . . . . . . . . . . . . . . . 2-16
single slot USB . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
charging indicators . . . . . . . . . . . . . . . . . . . . 2-4
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
charging indicators . . . . . . . . . . . . . . . . . . . 2-22
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
creating cpf file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
D
data capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
data connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
decode distances
DL focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-9
SR focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
decode zones
DL focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1, 4-4
CAB files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
digital signatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
disabling PIN for phone use . . . . . . . . . . . . . . . . . . . 5-8
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
E
EMDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
See EMDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
enabling PIN for phone use . . . . . . . . . . . . . . . . . . . . 5-7
enterprise mobility developer kit . . . . . . . . . . . . . 2-2, 4-9
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Ethernet cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
F
fabric holster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
flash file system
copyfile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
regmerge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
four slot Ethernet cradle . . . . . . . . . . . . . . . . . . 2-1, 2-10
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
charging indicators . . . . . . . . . . . . . . . . . . . . . . . 2-13
daisychaining . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
link indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10, 2-15
speed indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
four slot spare battery charger . . . . . . . . . .2-1, 2-3, 2-23
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
charging indicators . . . . . . . . . . . . . . . . . . . . . . . 2-23
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
G
GPRS
data connection . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
registry file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
WAN configuration . . . . . . . . . . . . . . . . . . . . . . . . 5-5
GSM
access point name . . . . . . . . . . . . . . . . . . . . . . . . 5-5
configure GPRS data connection . . . . . . . . . . . . . 5-5
settings
phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7, 5-8
security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
services . . . . . . . . . . . . . . . . . . . . . . . . . 5-8, 5-9
H
holster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
I
image update
deploying CAB files . . . . . . . . . . . . . . . . . . . . . . . 4-5
information, service . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
installing battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
internet
Index - 3
wireless connection . . . . . . . . . . . . . . . . . . . . . . 5-5
K
removing main battery . . . . . . . . . . . . . . . . . . . . . . . . 1-8
reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
rigid holster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
S
L
screen
calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
screen protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
device management . . . . . . . . . . . . . . . . . . . . . . 4-3
digital signatures . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
locking device . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
remote API . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
service information . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
services, GSM
call barring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
call forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
call waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
caller id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
voice mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
settings
GSM/GPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
SIM card
accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
single slot USB cradle . . . . . . . . . . . . . . . . . . . . . . . . 2-3
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
charging indicators . . . . . . . . . . . . . . . . . . . . . . . 2-4
spare battery
3600 mAh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
spare battery charger . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
charging indicators . . . . . . . . . . . . . . . . . . . . . . 2-23
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
spring loaded stylus . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
SR focus decode distances . . . . . . . . . . . . . . . . . . . . A-7
starting the EDA . . . . . . . . . . . . . . . . . . . . . . . . . 1-2, 1-6
storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
application folder . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
cache disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
persistent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
volatile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
storage card
deploying CAB files . . . . . . . . . . . . . . . . . . . . . . . 4-4
strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1, 2-2
subscriber identification module . . . . . . . . . . . . . . . . . 1-3
suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
lithium-ion battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
locking EDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
M
main battery
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2, 1-5
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
MMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
multi media card . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
N
network
configuring GPRS WAN . . . . . . . . . . . . . . . . . . . 5-5
network activation
CDMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
GSM/UMTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
O
operating environment . . . . . . . . . . . . . . . . . . . . . . . A-1
operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
P
packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
persistent storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
phone security . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7, 5-8
phone settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
PIN, changing for phone . . . . . . . . . . . . . . . . . . . . . . 5-7
PIN, disabling for phone use . . . . . . . . . . . . . . . . . . . 5-8
PIN, enabling for phone use . . . . . . . . . . . . . . . . . . . 5-7
pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
R
radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
random access memory . . . . . . . . . . . . . . . . . . . . . . 4-8
RAPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
regmerge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
remote API . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Index - 4
MC65 Integrator Guide
T
technical specifications . . . . . . . . . . . . . . . . . . . . . . . A-1
accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
U
unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
USB charge cable . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
USB charging cable . . . . . . . . . . . . . . . . . . . . . .2-1, 2-25
USB client charge cable . . . . . . . . . . . . . . . . . . . . . 2-25
USB cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
V
vehicle cradle . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1, 2-18
charging indicators . . . . . . . . . . . . . . . . . . . . . . 2-22
vehicle holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
voice mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
volatile storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
W
wakeup conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
waking EDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
wall mount bracket . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
wall mounting kit, cradle . . . . . . . . . . . . . . . . . . . . . . 2-2
wireless
internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
WLAN 802.11a/b/g . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
WPAN Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
WWAN
configuring GPRS . . . . . . . . . . . . . . . . . . . . . . . . 5-5
X
XML provisioning . . . . . . . . . . . . . . . . . . . . . . . . .4-6, 4-7
certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Motorola Solutions, Inc.
1301 E. Algonquin Rd.
Schaumburg, IL 60196-1078, U.S.A.
http://www.motorolasolutions.com
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered
trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are
the property of their respective owners.
© 2012 Motorola Solutions, Inc. All Rights Reserved.
72E-142435-02 Revision B - June 2012