Matrix SETU ATA211 SIP-FXS-FXO Specifications

SETU ATA211
System Manual
SETU ATA211
VoIP-FXS-FXO Adaptor
System Manual
Documentation Disclaimer
Matrix Comsec reserves the right to make changes in the design or components of the product as engineering and
manufacturing may warrant. Specifications are subject to change without notice.
This is a general documentation for all models of the product. The product may not support all the features and
facilities described in the documentation.
Information in this documentation may change from time to time. Matrix Comsec reserves the right to revise
information in this publication for any reason without prior notice. Matrix Comsec makes no warranties with respect
to this documentation and disclaims any implied warranties. While every precaution has been taken in the
preparation of this system manual, Matrix Comsec assumes no responsibility for errors or omissions. Neither is any
liability assumed for damages resulting from the use of the information contained herein.
Neither Matrix Comsec nor its affiliates shall be liable to the purchaser of this product or third parties for damages,
losses, costs or expenses incurred by the purchaser or third parties as a result of: accident, misuse or abuse of this
product or unauthorized modifications, repairs or alterations to this product or failure to strictly comply with Matrix
Comsec's operating and maintenance instructions.
Copyright
All rights reserved. No part of this system manual may be copied or reproduced in any form or by any means
without the prior written consent of Matrix Comsec.
Version 3
Release date: February 2, 2011
Contents
Introduction..................................................................................................................................................... 1
Welcome! ............................................................................................................................................................ 1
About this System Manual .................................................................................................................................. 1
How to Read this System Manual ....................................................................................................................... 2
Knowing SETU ATA211 .................................................................................................................................. 5
The Overview ...................................................................................................................................................... 5
Applications of SETU ATA211 ............................................................................................................................ 7
Getting Started ................................................................................................................................................ 9
Preparing for Installation ..................................................................................................................................... 9
Connecting SETU ATA211 ............................................................................................................................... 11
Configuring SETU ATA211 ............................................................................................................................... 13
Basic Settings ............................................................................................................................................... 19
Region ............................................................................................................................................................... 20
SIP Trunks ........................................................................................................................................................ 23
FXO Port ........................................................................................................................................................... 37
FXS Port ............................................................................................................................................................ 49
Passwords ......................................................................................................................................................... 57
Network Parameters ......................................................................................................................................... 61
Advanced Settings ....................................................................................................................................... 67
System Parameters ........................................................................................................................................... 67
Called Party Number Table ............................................................................................................................... 73
Dialed Number Table ........................................................................................................................................ 76
Peer-to-Peer Numbers ...................................................................................................................................... 79
Digest Authentication ........................................................................................................................................ 83
Daylight Savings Time ...................................................................................................................................... 86
Static Routing Table .......................................................................................................................................... 89
Restart SETU ATA211 ...................................................................................................................................... 92
Reinstate Factory Defaults ................................................................................................................................ 93
Software Upgrade ............................................................................................................................................. 95
Syslog (Debug) ................................................................................................................................................. 97
PCAP Trace .................................................................................................................................................... 100
Auto Configuration .......................................................................................................................................... 103
Features of SETU ATA211 .......................................................................................................................... 107
Call Hold .......................................................................................................................................................... 107
Table of Contents
i
Making a Second Call ..................................................................................................................................... 108
Call Transfer .................................................................................................................................................... 109
Call Toggle ...................................................................................................................................................... 111
Call Waiting ..................................................................................................................................................... 112
Conference ...................................................................................................................................................... 115
Do Not Disturb (DND) ..................................................................................................................................... 116
Call Forward .................................................................................................................................................... 118
Caller ID Restriction ........................................................................................................................................ 122
Selective Trunk Access ................................................................................................................................... 123
Speed Dialing .................................................................................................................................................. 124
Supplementary Services of Service Provider .................................................................................................. 127
Multi Stage Dialing .......................................................................................................................................... 128
Disconnect the Call ......................................................................................................................................... 133
Making New Call ............................................................................................................................................. 134
PIN Authentication .......................................................................................................................................... 135
System Status ............................................................................................................................................. 137
Viewing System Status from Jeeves ............................................................................................................... 137
Viewing System Status on Phone ................................................................................................................... 142
Appendix ..................................................................................................................................................... 145
Call Progress Tone Generation ...................................................................................................................... 145
Ring Cadences ................................................................................................................................................ 146
Frequently Asked Questions (FAQs) .............................................................................................................. 147
Acronyms ........................................................................................................................................................ 150
Features at a Glance ....................................................................................................................................... 152
Product Specifications ..................................................................................................................................... 153
System Commands ......................................................................................................................................... 156
Warranty Statement ........................................................................................................................................ 157
Regulatory Information .................................................................................................................................... 159
Open Source Licensing Terms and Conditions ............................................................................................... 161
Index ............................................................................................................................................................ 169
ii
Table of Contents
CHAPTER 1
Introduction
Welcome!
Welcome to the world of Telecom Solutions. Thank You for choosing SETU ATA211. This product is designed to
give you the highest performance, combined with real ease of use. We hope you will make optimum use of this
intelligent, intuitive, feature-packed VoIP Phone Adapter. Please read this document before installing SETU
ATA211.
About this System Manual
This document contains detailed information and instructions for installing, configuring, and operating SETU
ATA211. It also contains information on maintenance and safety instructions.
Intended Audience
This System Manual is aimed at:
Network Administrator and System Engineers: who will install, maintain and support SETU ATA211. It is
assumed that they have some experience in installing VoIP Phone Adapter and are familiar with VoIP
technology.
End Users, the persons/organizations who will use SETU ATA211. They include home users, personnel of
small and medium businesses, large enterprises, other commercial and public organizations/institutions.
Organization of this document
This System Manual contains the following topics:
Introduction: Gives information about this system manual.
Know Your SETU ATA211: Provides overview of SETU ATA211.
Getting Started: Contains information on how to install SETU ATA211, how to configure the device using the
web-based programming tool, Jeeves, and using the phone connected to the device.
Configuring Basic Settings: Provides instructions for configuring the basic parameters of SETU ATA211,
which are sufficient to get the system into operation.
Matrix SETU ATA211 System Manual
1
Configuring Advanced Settings: Contains instructions for configuring the more advanced features and
facilities of SETU ATA211.
Features of SETU ATA211: Describes in detail, the features of SETU ATA211, along with instructions for
configuring and using these features.
System Status: Describes the status indicators for the LAN and WAN ports, SIP trunk registration, and
details of the System Firmware.
How to Read this System Manual
This System Manual is organized in a manner to help you get familiar with SETU ATA211, learn how to install it,
how to connect it to the IP network, how to configure the Basic Settings that allow you to start making and receiving
calls, and move on to the Advanced configuration to use the special features and functions. You may read it in the
sequence it is organized.
Conventions used in this System Manual
Instructions
The instructions in this document are written in a step-by-step format. Each step, its result, indication/notification,
where and as it occurs, has been described.
Notices
The following symbols have been used for notices to draw your attention to important items.
Important: to indicate something that requires your special attention or to remind you of something you
might need to do when you are using the system.
Caution: to indicate an action or condition that is likely to result in malfunction or damage to the system or
your property.
Warning: to indicate a hazard or an action that will cause damage to the system and or cause bodily harm.
Tip: to indicate a helpful hint giving you an alternative way to operate the system or carry out a procedure
more efficiently.
Cross References
Cross references are highlighted in blue font and hyperlinked. You may click on the hyperlinked text to reach the
source of the cross-reference.
Terminology used in this System Manual
The technical terms and Acronyms used in this manual are standard terms, commonly used in the
telecommunications and data communications industry. Considering the broad group of intended users of this
manual, wherever possible, use of jargon is avoided.
Acronyms have been defined in the text and a complete list of Acronyms used in this document is provided in the
Appendix.
2
Matrix SETU ATA211 System Manual
The words ATA, ATA211, SETU ATA211, System and gateway means SETU ATA211.
Some of the terms specific to this manual that you will encounter freguently are defined below:
•
Admin: A person who installs, configures and maintains SETU ATA211. Admin can also be the user.
Admin has full accessibility of the system.
•
User: A person who uses SETU ATA211. User has limited access to the system
•
Caller/Calling party: A person making a call.
•
Callee/Called party: A person receiving a call.
•
Remote user/Remote party/Remote end: The person with whom the user interacts.
•
Transferor: The user who transfers the call.
•
Transferee: The remote user whose call is to be transferred (first party) to another remote user (second
party).
•
Transfer Target: The remote user to whom the call is to be transferred (second party).
•
LAN administrator: A person who maintains the LAN network of an organization.
Using this manual, you will be able to install, operate and make optimum use of SETU ATA211. If you encounter
any technical problems, please contact your Dealer/reseller or Matrix for support.
Matrix SETU ATA211 System Manual
3
4
Matrix SETU ATA211 System Manual
CHAPTER 2
Knowing SETU ATA211
The Overview
ATA211 is a VoIP-FXS-FXO Adapter. It allows you to make and receive voice calls over IP Network as well as
PSTN network using a conventional telephone instrument.
ATA211 uses SIP (Session Initiation Protocol) protocol to make voice calls over the IP network. It converts the
voice traffic into IP packets for transmission over the internet. When a telephone number is dialed by you, ATA211
converts it into an IP call using the Session Initiation Protocol (SIP) and initiates a call, thereby making VoIP calls
as easy as normal telephone calls. You also have the flexibility to make a call by selecting any SIP Trunk or the
FXO port.
Using ATA211, you can make VoIP calls and browse the Internet simultaneously.
SETU ATA211 can be used in residences, small and home offices, offices of medium and large enterprises.
SETU ATA211 supports 3 SIP trunks, allowing you to subscribe with three different Internet Telephony Service
Providers or to use the SIP trunks for Peer-to-Peer Calls.
Matrix SETU ATA211 System Manual
5
For the ease of configuration, SETU ATA211 has a an embedded, HTTP Web server with an graphic user interface,
which you can access by connecting a computer to SETU ATA211.
Ports and Connectors
Port Name
Connector
Description
Power
DC Jack
Power Adapter, to connect 12VDC, 1.00A power adapter.
LAN
RJ45
To connect a standalone computer or a LAN Switch.
WAN
RJ45
To connect to the IP network over a DSL Modem or Router or a LAN Swtich
FXS
RJ11
To connect a standard telephone instrument or a PBX.
FXO
RJ11
To connect a PSTN line or a PBX.
LEDs
SETU ATA211 has an LED each for the FXS port, FXO Port, the SIP Trunks (SIP1, SIP2) and POWER, to indicate
the status of the ports, and various events occurring on the ports, including errors.
6
POWER
FXO
FXS
SIP1
SIP2
The LEDs on the module are as shown in the figure below.
Matrix SETU ATA211 System Manual
Applications of SETU ATA211
ATA211 finds its application in following scenarios:
1. Residential Application - Home users use SETU ATA211 to make low-cost international calls to family,
friends and relatives.
IP Network
FXS
ATA211
Broadband
Modem/Router
LAN
FXO
Proxy
PSTN
2. SOHO Application - Small Office owners use SETU ATA211 to make low-cost calls to their overseas
customers, employees, suppliers, etc
IP Network
FXS
PBX
WAN
Broadband
Modem/Router
FXO
ATA211
LAN
Proxy
PSTN
Matrix SETU ATA211 System Manual
7
3. Business Application - Corporate Offices use SETU ATA211 to make low-cost international calls to their
overseas customers, employees, suppliers, etc.
IP Network
Proxy
FXS1
PBX
WAN
ATA211
Broadband
Modem/Router
Switch
LAN
FXO
PSTN
4. Peer-to-Peer Calls Application - Corporate Offices also use SETU ATA211 to communicate between
various branch offices, at no cost..
Location D
Location A
FXS
FXS
WAN
ATA211
WAN
ATA211
Broadband
Modem/Router
LAN
LAN
IP Network
Location C
Location B
Broadband
Modem/Router
FXS
WAN
ATA211
LAN
8
FXS
WAN
ATA211
LAN
Matrix SETU ATA211 System Manual
CHAPTER 3
Getting Started
Preparing for Installation
Package Contents
SETU ATA211
Adaptor 12V, 1.25Amp
(Country Specific)
Quick Start and User Card
Ethernet Cable (RJ45)
CD containing System Manual,
Quick Start and User Card
Two Screws M 7/30
Two Screw Grips
RJ11 Line Cord
Warranty Card Set
1. Unpack SETU ATA211.
2. Verify the package contents. Contact your vendor/Service Provider/system administrator, if any of the
above listed items is missing or damaged.
Protecting SETU ATA211
You are recommended to take the measures listed in the following protect yourself and SETU ATA211.
Installation Precautions
Do not install the system in a place where
• it may be exposed to direct sunlight, excessive cold or humidity.
• it may be exposed to dust, water, oil, corrosive fumes.
• it may fall, causing damage to the product.
• shocks or vibrations are frequent or strong.
• there is a water source or body, like a wash basin/kitchen sink, bath-tub, a swimming pool, sprinkler, etc.
Make sure there is enough open space for ventilation at the site of installation.
Matrix SETU ATA211 System Manual
9
Safety Instructions
Take every measure to reduce the risk of fire, electric shock and injury to the person handling this product.
•
•
•
•
•
•
•
Read all the instructions given in this manual.
Always switch off the product, unplug the product from the wall outlet when handling it. Removing covers
or opening the system or incorrect reassembly increases the risk of electric shock.
Never open the system in power ON condition.
Use the adapter provided with the product.
Make sure Interfacing cables not touch exposed power line cable.
Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
Unplug the product from the wall outlet before cleaning.Do not use liquid cleaners. Use only dry and soft
cloth.
Always get your product serviced by a trained, qualified person. Contact your authorised dealer or Matrix support,
if:
• liquid has been spilled into the product or the product has been exposed to rain or water.
• the product has been dropped or the cabinet has been damaged.
• the product does not operate normally or exhibits a distinct change in performance.
Mounting the SETU ATA211
To mount SETU ATA211 on the wall,
• Select a suitable place.
• Use the mounting template provided to you to drill holes of appropriate size and distance.
• Fix the screw grips in the holes you drilled.
• Fix the screws in the holes, leaving the screw heads protruding a few millimeters from the wall.
• Check the strength of the screws.
• Mount SETU ATA211 on the wall.
10
Matrix SETU ATA211 System Manual
Connecting SETU ATA211
•
Connect a standalone computer/ LAN Switch to the LAN Port of SETU ATA211 using an Ethernet cable.
•
Connect the WAN Port of SETU ATA211 to the IP Network—a DSL modem or Router or a LAN
Switch—using the Ethernet cable provided to you.
•
Connect a telephone to the FXS Port of SETU ATA211, using a standard telephone cable with an RJ11
plug.
You may also connect a PBX to the FXS port of SETU ATA211.
•
Connect the PSTN line to the FXO Port of SETU ATA211, using a standard telephone cable with an RJ11
plug.
You may also connect PBX to the FXO port of SETU ATA211.
•
Connect the power adapter provided with SETU ATA211 to the power jack labeled 12VDC-1A(MAX).
•
Connect the adapter plug into a power outlet.
•
Switch ON power.
•
Wait for the Reset Cycle to complete.
POTS
Power
Adaptor
IP
DSL Modem/
Router
PC/LAN
Reset Recycle
•
At Power ON,
• POWER LED will glow Green, continuously.
• All LEDs—FXS, FXO, SIP1 and SIP2 —will blink Red thrice (250 ms On - 250 ms Off).
Matrix SETU ATA211 System Manual
11
•
On successful completion of initialization cycle, each LED will glow as per the call conditions as
summarized below:
LED Status
Meaning
FXS Continuously ON
Indicates that FXS port is either Off-hook or in speech during
incoming call / outgoing call.
Blinks fast 200ms ON,
200ms OFF
Indicates that FXS port is in Error state during incoming/outgoing
call.
Blinks slow 500ms ON,
500ms OFF
Indicates that FXS port is Ringing for incoming call or Number is
being dialed for outgoing call (After end of dialing).
Continuously OFF
Indicates that FXS port is in On-hook.
FXO Continuously ON
Indicates that FXO port is either Off-hook or in speech during
incoming/outgoing call.
Blinks fast 200ms ON,
200ms OFF
Indicates that FXO port is in Error state during incoming/outgoing
call.
Blinks slow 500ms ON,
500ms OFF
Indicates that FXO port is Ringing for incoming Call or Number is
being dialed for outgoing call (After end of dialing).
Continuously OFF
Indicates that FXO port is On-hook.
SIP1 Continuously ON
Indicates that SIP1 is enabled and is registered with the SIP server
or 'Active' status of SIP Trunk.
Blinks fast 200ms ON,
200ms OFF
Indicates that SIP1 is enabled but not registered with the SIP server
(SIP is configured as proxy).
Blinks slow 500ms ON,
500ms OFF
Indicates that SIP1 is enabled but not registered with the SIP server
(SIP is configured for P2P calling).
Continuously OFF
Indicates that SIP1 is disabled.
SIP2 Continuously ON
Indicates that SIP2 is enabled and is registered with the SIP server
or 'Active' status of SIP Trunk.
Blinks fast 200ms ON,
200ms OFF
Indicates that SIP2 is enabled but not registered with the SIP server
(SIP is configured as proxy).
Blinks slow 500ms ON,
500ms OFF
Indicates that SIP2 is enabled but not registered with the SIP server
(SIP is configured for P2P calling).
Continuously OFF
Indicates that SIP2 is disabled.
You can also view the status of the ports on the Status page of the web-based graphical user interface of SETU
ATA211. See “System Status”.
12
Matrix SETU ATA211 System Manual
Configuring SETU ATA211
SETU ATA211 provides access to system configuration at two levels: Admin and User. A distinct set of features
and facilities can be configured at each of these levels.
SETU ATA211 can be configured using its Web-based graphic user interface (GUI) and from the phone connected
to its FXS port. While the entire system configuration can be done using the GUI, you can configure only certain
parameters from the phone.
Admin Mode
Admin is defined as the person who installs, configures and maintains the SETU ATA211. The Admin can also be
the User. In the Admin mode, you have full access to system configuration, all configurable parameters, features
and facilities, and system maintenance:
• Basic Settings
• Advanced Settings
• Supplementary Services
Access to Admin mode is protected by a password. The default Admin Password is 1234. The password may be
changed.
User Mode
In the User mode, you can configure (enable/disable, set/cancel) specific features and facilities of SETU ATA211,
as listed below:
• Supplementary Features
• Speed Dialing
• Network parameters
• User Password
• Syslog (debug)
• Factory Defaults
• PCAP
Access to the User mode is also protected by a password, referred to as the User Password. The default User
Password is 1234. The password may be changed.
Configuration using Web-based GUI: Jeeves
SETU ATA211 has a graphic user interface (GUI), Jeeves, an easy-to-use proprietary software of Matrix for system
configuration. Jeeves is an embedded, web server which you can access from the computer you connected to the
LAN Port or the WAN Port of SETU ATA211.
Jeeves allows system configuration in the Admin mode and User mode.
To access Jeeves, follow these steps:
•
Connect a standalone computer to the LAN port of SETU ATA211. The LAN Port of SETU ATA211 and that
of the computer must be in the same Subnet.
The default IP Address of the LAN port of SETU ATA211 is: 192.168.002.006
The default Subnet Mask of the LAN port of SETU ATA211 is: 255.255.255.0
Matrix SETU ATA211 System Manual
13
If required, change the IP Address and the Subnet of the computer.
You may also connect the LAN port of SETU ATA211 to a computer on LAN. If you connect the LAN port
of SETU ATA211 to a LAN Switch, make sure that the IP Address of LAN port of SETU does not conflict
with the IP Address of any device on the LAN, and SETU ATA211 is in the same Subnet as the LAN
computer.
You may change the IP Address and Subnet Mask of the LAN Port of SETU ATA211 by dialing the
relevant System Commands from the phone connected to the FXS port of SETU ATA211. See the topic
“Configuring using a Phone”.
When installing the system for the first time, you are advised to connect SETU ATA211 to a standalone
computer only.
•
Make sure a web-browser, either Internet Explorer Version 7 or higher or Mozilla Firefox 3.5 or higher, is
installed on the computer.
•
Open the browser on the computer.
•
Type 192.168.002.006, the default IP address of the LAN port of SETU ATA211, in the address bar of the
browser and press Enter key/click Go.
If you have connected SETU ATA211 to the LAN and have changed the IP Address of the LAN port of
SETU ATA211, enter the current IP Address in the address bar of the browser.
The Login page of Jeeves opens.
You can also use the WAN Port of SETU ATA211 to access the embedded web server in the same
manner.
The default IP Address of the WAN Port of SETU ATA211 is: 192.168.001.171
The default Subnet Mask of the WAN Port of SETU ATA211 is: 255.255.255.0
14
Matrix SETU ATA211 System Manual
On the Login page of Jeeves, you are offered two Login modes: Admin and User.
To log in as Admin,
•
In the Login as box, select Admin.
•
In the Password field, enter 1234, the default Admin Password.
•
Click the Login button.
•
On successful login, the Admin mode page will open.
•
The left pane shows the links Basic Settings, Advanced Settings, Supplementary Services, and
Status.
Basic Settings are sufficient to get your SETU ATA211 into operation.
•
Click the links to expand.
To log in as User,
Matrix SETU ATA211 System Manual
15
•
In the Login as combo box, select User.
•
In the Password field, enter 1234, the default User Password.
•
Click the Login button.
•
On successful login, the User mode page will open.
•
The left pane displays User Settings and Status links.
•
Click the User Settings link to expand. The sub-links to the functions and features that are allowed
to be configured from the User mode appear on the left pane: Supplementary Features, Speed
Dialing, Network, User Password, Syslog, and Factory Defaults.
•
Click the Status link to view the status of the system and the ports.
Configuring using a Phone
You can enter the Admin mode and the User mode using the phone connected to the FXS Port of SETU ATA211,
and change feature settings, and certain network parameters like the IP Address and Subnet Mask of the LAN and
the WAN port of SETU ATA211, select the Connection Type (IP Addressing) by dialing “System Commands” from
the phone connected to the FXS port of SETU ATA211.
You can also dial System Commands to view the current IP Addresses of the WAN and LAN Ports (if your phone
has a display).
Follow the instructions given below to configure the system from the phone.
Admin Mode
16
•
Lift the receiver of the phone.
•
Dial #19 to enter the Admin mode.
Matrix SETU ATA211 System Manual
•
Dial the Admin Password (default: 1234).
You will get programming tone.
•
Dial the System Command for the feature/facility you want to configure.
For example:
To change IP Address of the LAN Port dial 12<LAN IP Address>#*
For example, to change the IP address to 192.168.1.120, dial 12192168001120#*
•
When you dial a valid command, SETU ATA211 plays a confirmation tone for 3 seconds, and plays the
programming tone.
•
Dial 0 to exit configuration mode.
When network parameters are changed, SETU ATA211 will restart, without dial tone/confirmation tone.
You can also view the Network parameters (IP Address, Subnet Mask, Connection Type. etc.) on the phone’s
display. See “System Status”.
For a complete list of commands, refer “System Commands” in the Appendix.
User Mode
•
•
•
•
•
Lift the receiver of the phone.
Dial #18 to enter the User mode.
Dial the User Password (default: 1234).
You will get programming tone.
Dial the command for the feature/facility you want to configure.
For example,
To configure the destination number for Call Forward -Unconditional, dial 51-Destination Number-#*
• To configure 2001 as the destination number for Call Forward-Unconditional, dial 512001#*
•
Dial 0 to exit programming mode.
For a complete list of commands, refer “System Commands” in the Appendix.
Matrix SETU ATA211 System Manual
17
18
Matrix SETU ATA211 System Manual
CHAPTER 4
Basic Settings
The Basic Settings enable you to configure SETU ATA211 for basic functions. As Basic Settings cover much of
your configuration requirements, you will be able to operate and use the system efficiently, when you configure
Basic Settings.
To configure Basic Settings,
•
Click Basic Settings link.
The links to the different basic parameters appear on the left pane.
There are two ways to configure Basic Settings:
•
Using the Wizard. The Wizard will guide you step-by-step through the configuration.
OR
•
Selectively configuring the Basic Settings parameters, by clicking the links on the left pane.
To use the Wizard,
Matrix SETU ATA211 System Manual
19
•
Click the Wizard
icon on the top right of your screen.
•
The Next button takes you to the next page, saving the changes you made on the current page.
•
The Back button returns you to the previous page.
•
The More
button expands parameters on the page.
•
The Less
button collapses parameters on the page.
•
The Default button assigns factory set values to all the parameters on the page.
•
The Quit
button allows you to exit the Wizard at any stage, saving changes you made before
exiting.
To use selective configuration,
• Click Basic Settings link to expand.
• Click each parameter link, Region, SIP, FXO, FXS, Passwords, Network.
• The selected parameter page opens.
• The More button expands parameters on the page.
• The Less button collapses parameters on the page
• Set the desired values on the page.
• Click Submit to save your settings on the page.
You may use the Wizard or selectively configure the Basic Settings pages, whichever works best for you.
The instructions provided in this chapter, describe selective configuration of the Basic Settings pages.
1. Click Basic Settings to expand.
2. The following links appear under Basic Settings:
•
•
•
•
•
•
Region
SIP
FXO
FXS
Passwords
Network
Each of these are explained in detail in the following.
Region
1. Click Region.
20
Matrix SETU ATA211 System Manual
2. Click More button to view all parameters on the page.
3. Select Admin Language and User Language. Default: English.
SETU ATA211 can display the Admin and User pages of the GUI, Jeeves, in the following languages:
• English
• Italian
• Spanish
• French
• German
• Portuguese
All the Admin and User Pages of the GUI will appear in the language you selected, when you login again
as Admin or User.
You can also select a Language on the Login page; however, it will be applied for the current session only.
4. Select CPTG (Call Progress Tone Generation) to match the CPTG of the country where SETU ATA211 is
installed. Default: India.
The SETU ATA211 supports country specific Call Progress Tones Generation (CPTG) to simulate the
same tones of the local PSTN to which it is connected. The CPTG supported by SETU ATA211 for different
countries are presented in the “Appendix”.
When you reset SETU ATA211 to factory defaults, CPTG you selected will not be set to default.
5. Select Ring cadence to match the ring cadence of the country where SETU ATA211 is installed. Select
your country from the drop down list. Default: India.
During an incoming call, SETU ATA211 will play the ring over the SLT as per the Ring Cadence of the
country you selected. For a complete list of Ring Cadences of different countries supported by SETU
ATA211, see “Appendix”.
When you reset SETU ATA211 to factory defaults, the Ring you selected will not be set to default.
Matrix SETU ATA211 System Manual
21
6. To synchronize Date and Time of SETU ATA211 with that of the country where it is installed, select Time
Zone from the drop down list. Default: (GMT+05:30) Kolkata, Chennai, Mumbai, New Delhi.
7. To use a public internet time server for date and time synchronization, select an internet based time server
as NTP Server. You may select any of the three reliable public internet time servers1 supported by SETU
ATA211:
• ntp1.cs.wisc.edu
• time.windows.com
• time.nist.gov
Default: Ntp1.cs.wisc.edu
If you want to use an NTP server other than these, select the radio button and enter the IP Address/
domain of the server in the empty field.
When you reset SETU ATA211 to factory defaults, Date and Time settings will not be set to default.
8. Click Submit to save your region settings.
1. You can select from three free, reliable public internet time servers run by the University of Wisconsin-Madison, Microsoft, and the
National Institute of Standards and Technology (NIST), to obtain date and time. You can also configure an NTP time server of your
preference, other than these. These public internet time servers provide time offset from the Greenwich Mean Time (GMT), and you
can select the time according to the time zone of the country you are installing the SETU ATA211. For instance, if your SETU ATA211
is installed in India, you can select the time zone for India (GMT+5.30 Calcutta, Chennai, Mumbai, and New Delhi). The time for India
is offset from GMT by +5.30 hours. Similarly, if your SETU ATA211 is installed in Hawaii, select the time zone for Hawaii, which is offset by GMT -10:00 hours, to set the correct time and date.
22
Matrix SETU ATA211 System Manual
SIP Trunks
SETU ATA211 supports three SIP trunks, which may be configured as Proxy or Non-Proxy, i.e. Peer-to-Peer trunks.
You may register with three different ITSPs and use their services.
1. Click the link SIP.
The parameters of SIP Trunk 1 appear on your screen.
2. Click More button to view all parameters of SIP Trunk 1 on this page.
Matrix SETU ATA211 System Manual
23
Trunks Settings
1. Select the check box Enable to use the SIP Trunk. Default: Disabled.
You may disable the SIP trunk, if you do not want to include it in Call Routing.
2. Select SIP Trunk Mode according to your installation. Default: Peer-to-Peer.
•
Select Proxy, if you want to register this SIP trunk with an ITSP or a Registrar Server.
•
Select Peer-to-Peer, if you want to use the trunk for Peer-to-Peer (non-proxy) calls.
If you select Peer-to-Peer, you must also configure the number strings in the Peer-to-Peer Table.
•
24
Click the arrow icon to configure the Peer-to-Peer Table. A new window opens.
Matrix SETU ATA211 System Manual
•
You can configure as many as 500 number strings, which are stored against an Index number.
•
In the Number field, enter the peer-to-peer number string—prefix or entire number—that will be
dialed. The number string must not exceed 24 characters. Default: Blank.
If the number to be dialed out is <dialednumber@destination address>, for example,
123@abc.com, you must enter 1234 in this field.
•
To identify the number string you configured, enter a name in the Name field. It may be the name of
your contact or any name you wish to assign to the number string. The name may consist of 24
characters (maximum). Default: Blank.
•
As Minimum Digits, define the minimum length of the number string that must be dialed for the
system to consider it as a valid number. Default: 01.
If the peer-to-peer number string you dial is shorter than the Minimum Digits you have configured,
the system will not dial out the number.
•
As Maximum Digits, define the maximum length of the number string that must be dialed out for
the system to consider it the complete number string. Default: 24.
If the peer-to-peer number string you dial is longer than the Maximum Digits you have configured,
the system will strip off the additional digits and dial out the number.
•
In the Destination Address field, enter the domain name or IP Address to where the dialed peerto-peer number string is to be sent. The Destination Address may consists of up to 40 characters.
Default: Blank.
For example, if the peer-to-peer number to be dialed out is 123@abc.com, enter abc.com as
Destination Address. If the number is 1234@ 192.168.1.197, enter 192.168.1.197 as the
Destination Address. The Destination Address can also be in the form of Address:Port number.
Matrix SETU ATA211 System Manual
25
•
the Click Submit to save entries.
•
Close the window.
3. Enter the SIP ID. This is the ID which remote parties will use to call this SIP Trunk. Default: Blank.
The SIP ID may be a number or text consisting of a maximum of 40 characters.
If you have defined the trunk mode as Proxy, enter the SIP ID provided by your ITSP. For example, if SIP
URI provided by the ITSP is 12345@abc.com, enter 12345 in this field.
If you have defined the trunk mode as Peer-to-Peer, enter the desired SIP ID.
4. Enter Authentication ID. Default: Blank.
If you have defined the SIP trunk mode as Proxy, enter the Authentication ID (User ID) provided by your
ITSP.
If you have defined the trunk mode as Peer-to-Peer, enter the ID of your preference as Authentication ID.
5. Enter Authentication Password. Default: Blank.
If you have defined the SIP trunk mode as Proxy, enter the Authentication Password provided by your
ITSP.
If you have defined the trunk mode as Peer-to-Peer, enter a password of your preference as
Authentication Password.
6. SIP Registration is applicable for Proxy SIP Trunks only. Default: Disabled.
Select the check box to enable. SETU ATA211 will send the REGISTER message to Registrar proxy or
Outbound proxy as applicable.
7. Select the OG Calls without Registration check box to allow the users to make outgoing calls
irrespective of whether the SIP Trunk has been successfully registered with proxy or not.
By default, the system does not allow outgoing calls to be made if the status of the SIP trunk is 'not
registered'.
8. If you have defined the SIP trunk mode as Proxy, in the Registrar Server Address: Port field, enter the
Registrar Server Address and the Registrar Server’s listening port for SIP messages.
The registrar server address may be an IP address or a domain. Default: Blank.
The valid port range is: 1024-65534. Default: 5060.
9. If your service provider uses an outbound proxy for handling voice calls, enable Outbound Proxy check
box.
•
In the Outbound Proxy Server Address: Port field, enter the IP address or domain name of the
Outbound Proxy Server and the number of the Outbound Proxy Server’s Listening Port for SIP.
The Server Address may consist of maximum 40 characters. Default: Blank.
26
Matrix SETU ATA211 System Manual
The valid range for the port is 1024-65534. Default: 05060.
10. To add ‘rinstance’ in REGISTER? Message, keep this feature enabled. Default: Enabled.
‘rinstance’ is any random value which can be used by the SETU ATA211 to fetch its own contact binding,
i.e. to know the Registration Expiry Timer assigned by the server.
When you enable ‘rinstance’ in Register, SETU ATA211 will generate any random value of 'rinstance' and
include in the REGISTER message. The system will use the registration expiry timer of that contact
binding.
11. Set the Re-registration Timer. This is the time period after which the SETU ATA211 will send registration
request to maintain registration binding with the Registrar server.
The valid range of this timer is 00001- 65535. Default: 3600 seconds.
12. Define the Registration Retry Timer. When a registration attempt fails, SETU ATA211 will resend
registration request to the Registrar Server after the expiry of the Re-registration Timer. The valid range of
this timer is from 00001- 65535. Default: 10 seconds.
13. Click Submit.
Incoming Call
1. Select an appropriate Incoming Call Routing option for the SIP Trunk. Default: Route to FXS. You may
select:
Reject Incoming Calls: The system will reject all calls received on the SIP Trunk. Select this option, if
you want to block calls on this SIP trunk.
•
Route To FXS: The system will place all calls received on the SIP Trunk on the FXS port. The phone
connected to the port will start ringing for the duration of the Ring Timer (default: 45 seconds). If the call
is not answered within this timer, it will be rejected.
Matrix SETU ATA211 System Manual
27
•
Route to fixed destination number through FXO: The system will place all calls received on the SIP
Trunk to a Fixed Destination Number through the FXO port.
If you select this option, define the destination number in the Fixed Destination Number field.
•
Route to FXS. If not answered within ring timer, route to fixed destination number through FXO:
The system will place all calls received on the SIP Trunk on the FXS port. The phone connected to the
port will start ringing for the duration of the Ring Timer (default: 45 seconds). If the call is not answered
within this timer, the call will be automatically routed to the fixed destination number through the FXO
port.
If you select this option, define the destination number in the Fixed Destination Number field.
•
Answer the call and connect to FXO: The system will connect all calls received on the SIP Trunk on
the FXO port. You will get dial tone of the PSTN, if the FXO port is connected to the PSTN
exchange.You can now dial the desired number.
•
Route to FXS. If not answered within ring timer, answer the call and connect to FXO: The system
will place all calls received on the SIP Trunk on the FXS port. The phone connected to the port will start
ringing for the duration of the Ring Timer (default: 45 seconds). If the call is not answered within this
timer, the system will automatically connect the call to the FXO port. You will get dial tone of the PSTN
if the FXO port is connected to PSTN exchange. You can now dial the desired number.
•
Answer the call, collect number & route to FXS: Select this option, if FXS port of SETU ATA211 is
connected to the FXO port of the PBX and you want callers to reach extensions of the PBX by simply
dialing the extension number. When there is an incoming call on the SIP trunk, the call is answered and
dial tone is played to the caller. When the caller dials the number, ATA will collect the digits and route
the call from its FXS port.
•
Answer the call, collect number & route to FXO: Select this option, if you want the system to first
answer the call on the SIP trunk, play dial tone to the caller, and when the caller dials the number, to
collect the digits and route the call to the FXO port.
•
Route as per called party number: Select this option, if you want all incoming calls on the SIP trunk to
be routed on the basis of the Called Party Number received in INVITE message.
If you select this option, you must configure the Called Party Number Table.
To do this,
•
Click the arrow icon. The Called Party Number Table opens in a new window.
•
In this table, entries are stored at Index numbers from 02 to 10.
•
For each index number,
•
enter the desired Number (max. 24 characters) you want to store in the table.
The first Index number 01, is reserved for No Match Found. Start your entries from Index 02.
•
28
For the number you entered, define the Minimum Digits, which the system must receive to
consider it as a valid number. Default:01
Matrix SETU ATA211 System Manual
•
For the number you entered, define the Maximum Digits. The number received must not
exceed the maximum digits you have defined here. Default:24
•
For the number you entered, select the Destination Route. It may be the FXS or FXO port to
route the Called Party number.
Click Submit and close the window. To know more see “Called Party Number Table”.
2. Enter the Fixed Destination Number in this field, if the incoming call routing option requires the call to be
finally placed at a fixed destination. You can configure the fixed destination number of maximum 16 digits.
Default: Blank
3. Enter the time duration in the Ring Timer field, for which the system plays the ring on the FXS Port for an
incoming call. Range of the ring timer is of 01 to 99 seconds. Default: 45 sec.
4. To display CLI Number on FXS Port2, you may select:
•
•
Calling Number
Called Number
Default: Calling Number
5. Define the type of response the system should send on the receipt of an incoming call on the SIP trunk.
For the On Connecting Media, Send parameter, you may select:
• 183 Session Progress
• 200 OK
Default: 183 Session Progress
6. If you want to Authenticate Incoming Calls on SIP, that is, you want to allow incoming calls only after
callers have authenticated themselves. You can select:
•
Pin Authentication: Select this option to authenticate callers with a unique PIN.
•
Digest Authentication:Select this type of authentication if you want to allow incoming calls on the SIP
Trunk only after callers have authenticated themselves with their User ID and Password.
Default: Disabled.
If you have selected Pin Authentication, you must configure the PIN Authentication Table.
To do this,
2. SETU ATA211 supports display of Calling Line Identity (CLI) on the FXS Port, depending on number received in the request SIP message.
Matrix SETU ATA211 System Manual
29
•
Click the arrow icon.
•
The PIN Authentication Table page opens in a new window.
•
Enter the PIN to be authenticated against each Index in the Table.
PIN number can be a of maximum 4 digits. The characters allowed are: 0-9,*, #.
•
•
If you have finished entering, click Submit.
Close the window.
To know more about this feature, see “PIN Authentication”.
PIN Authentication is applicable when incoming call option on the SIP Trunk is selected as Answer the
call, collect the number and route to FXS OR Answer the call, collect the number and route to FXO.
If you select Digest Authentication, you must configure the Digest Authentication Table.
30
Matrix SETU ATA211 System Manual
To do this,
• Click the arrow icon.
•
The Digest Authentication Table page opens in a new window.
•
Enter the User ID to be authenticated along with its corresponding Password against each Index in
the Table.
The User ID may be a maximum of 40 characters. The User Password may be a maximum of 16
characters.
•
•
If you have finished entering the User IDs and their corresponding User Passwords in this Table,
click Submit.
Close the window.
To know more about this feature, see “Digest Authentication”.
Matrix SETU ATA211 System Manual
31
Vocoders
1. Select Vocoders in the order of preference from the multiple selection box.
Vocoders are the various voice codecs used to compress the data in RTP packets for optimum use of
bandwidth and for ensuring voice quality. You can set 4 Vocoder options in the order of preference.
The Vocoders supported by SETU ATA211 in the order of preference, i.e. 1st to 4th, listed in the Used
Codecs box are:
• G.711 A - Law
• G.711  Law
• G.729
• G.723
• To remove a Vocoder from this list, select the Vocoder and the back arrow <
• The Vocoder will be moved to the Unused Codecs box.
• Select the required Vocoders from the right list box with your cursor.
• Use the Up and Down arrows near the Used Codecs box to change the order of Vocoder preference..
2. If you have G.723 as a Preferred Vocoder, select G.723 Bit Rate as: 5.3 Kbps or 6.3 Kbps. Default:
6.3kpbs.
When G.723 is negotiated, the selected Bit Rate will be applied only when sending the RTP packets.
When receiving RTP packets from the remote end, both Bit Rates of G.723 will be accepted.
32
Matrix SETU ATA211 System Manual
Advanced
1. Select the default SIP Transport for outgoing SIP messages from the following options:
•
UDP: Outgoing messages are transported using UDP.
•
TCP: Outgoing messages are transported using TCP.
•
TCP (Fallback to UDP): TCP is used for outgoing messages. However, if the TCP connection fails, the
system will attempt to send the message again over UDP.
Default: UDP
To use TCP or TCP (Fallback to UDP), to must enable SIP over TCP in the “System Parameters” page.
2. Select the Automatic Number Translation check box, if you want to apply this feature on the SIP trunk.
Default: Disabled.
Automatic Number Translation (ANT) of SETU ATA211 modifies the number strings—entire numbers or
part thereof—you dial into number strings understood by the IP network.
The ANT feature is useful when the network requires adding or stripping off of parts of the dialed number
strings. For example, the PSTN requires you to dial the prefix 00 for calling international numbers,
whereas the ITSP you have subscribed this SIP trunk restricts the dialing of the prefix 00 for international
numbers. If you happen to dial this prefix, your call will be rejected by the ITSP.
ANT is also used when SETU ATA211 is deployed for networking between PBXs at multiple sites, and
“Multi Stage Dialing” is required.
To use ANT, select the check box and configure the Automatic Number Translation Table. To do this,
Matrix SETU ATA211 System Manual
33
•
Make a list of numbers that need to be modified before being dialed out from this SIP trunk. Make a list
of the corresponding modified numbers that the system should substitute the dialed numbers with.
•
Click the arrow icon.
•
The Automatic Number Translation table opens in a new window.
In this table, you can store as many as 24 Dialed Numbers and their corresponding Substitute
Numbers, at Index Numbers 01 to 24.
34
Matrix SETU ATA211 System Manual
•
In the Dialed Number column, enter the numbers that need to be modified when dialed out from this
SIP trunk.
•
In the Substitute Number column, enter the numbers which the system should dial out in place of the
dialed numbers.
Make sure you enter a Dialed Number and its corresponding Substitute Number at the same Index
number in the table. For example, if you entered 001 as Dialed Number at Index 01, you must enter its
corresponding Substitute Number 1 also at Index 01.
•
Click Submit to save your entries.
•
Close the window.
3. By default, the CLI of the SIP Trunk is sent to the called party when outgoing calls are made using the SIP
trunk. If you do not want to send CLI, enable the CLIR check box. Default: Disabled.
4. If you want the system to reject incoming calls which do not have the identity of the caller (Calling Party
Information), enable the Anonymous Call Rejection check box. Default: Disabled
5. If you want the system to send RTP packets to original IP and Port from where RTP packets are received,
by ignoring the contact information received in SDP, enable the Symmetric RTP check box. Default:
Disabled
6. If you want the system to send DNS SRV query to the configured domain server, enable DNS SRV. When
disabled, the system will send DNS A query to the configured domain server. Default: Disabled.
7. When the system is installed behind a NAT Router, select specific NAT traversal mechanism to be used as
NAT Type. Default: Disabled.
•
Select Router’s IP Address, if your ATA is located behind the NAT router (any type).
Make sure you disable Outbound Proxy on SIP trunk and configure the same IP Address under NAT
settings in the “System Parameters” page.
•
Select STUN if your ATA is located behind the NAT router other than Symmetric.
Make sure you disable Outbound Proxy on SIP trunk and configure the STUN Server Address and port
in “System Parameters”.
8. Select the appropriate DTMF sending/receiving mechanism that is compatible with the DTMF sending/
receiving mechanism of your ITSP or remote peer. SETU ATA211 supports:
• Inband
• Outband
• SIP (INFO)
Default: Outband
•
In the On Time field, set the time for which the DTMF digit should remain on, when the digit is dialed
out by the system. The DTMF On Time may be 100 or 150 or 200 milliseconds. Default: 100
milliseconds.
•
In the Off Time field, set the time for which system should wait before dialing the successive DTMF
digits. The DTMF Off Time may be 100 or 150 or 200 milliseconds. Default: 100 milliseconds.
Matrix SETU ATA211 System Manual
35
9. Configure the Pause Timer (sec), if you want to insert a delay before the digits of a number string is out
dialed from the SIP trunk.
The range of the Pause Timer is from 1 to 9 seconds. Default: 2 seconds.
10. Select an appropriate Call Hold Method that is compatible with your ITSP proxy server/remote peer.You
may select:
• RFC 2543
• RFC 3261
Default: RFC 3261
11. To send and receive the Fax over IP from and on the FAX machine connected to FXS port of the SETU
ATA211, select the desired Fax over IP protocol:
•
T.38(UDPTL): If you select this option, the device you are sending the fax to, must also support this
protocol.
•
Pass Through: Select this option if you need to send fax over G.711. The device you are sending fax
to must also use G.711.
Default: T.38 (UDPTL).
If the FAX sent using T.38 is rejected, SETU ATA211 will use Pass Through as the Fall Back protocol to
send the fax.
12. If you have completed the configuration of SIP Trunk 1, click Submit to save settings.
13. To configure another SIP trunk, click the SIP Trunk Number tab.
14. Follow the same instructions as described here to configure the next SIP trunk.
36
Matrix SETU ATA211 System Manual
FXO Port
SETU ATA211 supports a FXO Port,
•
•
which may be interfaced with the analog trunk from PSTN and used to route incoming calls to FXS port or
SIP trunks.
which may be interfaced with FXS port of the PBX.
To configure the FXO port parameters,
1. Click the link FXO.
2. Click More button to view all parameters on this page.
General
1. Select the Enable check box to use the FXO Port. Default: Disabled.
You may disable the FXO Port, if you do not want to include it in Call Routing.
2. You can assign a Name to the FXS port, which will be displayed to the called party (if the instrument of the
called party supports name display name functionality). Default: Blank
Matrix SETU ATA211 System Manual
37
The name you assign may consist of a maximum of 24 characters.
Incoming Call
1. Select an appropriate Incoming Call Routing option for the FXO Port. Default: Route to FXS. You may
select:
•
Ignore Incoming Calls: Select this option, if you do want to receive incoming calls on FXO port of
ATA211.
•
Route to FXS: The system will place all calls received on the FXO port on the FXS port. The phone
connected to the port will start ringing for the duration of the Ring Timer (default: 45 seconds). If the call
is not answered within this timer, it will be rejected.
If you select this option, you may configure the Ring Timer. Valid range: 01-99 sec.
•
Route to fixed destination number as per incoming call route selection: The system will place all
calls received on the FXO Port to a Fixed Destination Number as per the Incoming Call Route you
select: SIP1, SIP2, SIP3 or Dialed Number Table.
If you select this option, define the destination number in the Fixed Destination Number field and
select the Incoming Call Route.
•
Route to FXS. If not answered within ring timer, route to fixed destination number as per
incoming call route selection: The system will route all calls received on the FXO Port to the FXS
port. The phone connected to the FXS port will start ringing for the duration of the Ring Timer (default:
45 seconds). If the call is not answered within this timer, the call will be automatically routed to the
Fixed Destination number as per the Incoming Call Route you select: SIP1, SIP2, SIP3 or Dialed
Number Table.
If you select this option, define the destination number in the Fixed Destination Number field and
select the Incoming Call Route.
•
38
Answer the call, collect number & route as per incoming call route selection: Select this option, if
you want the system to first answer the call on the FXO port, play dial tone to the caller, and when the
caller dials the number, to collect the digits dialed by the caller and route the call as per the incoming
call route you select i.e SIP1, SIP2, SIP3 or Dialed Number Table.
If you select this option, select the Incoming Call Route.
Matrix SETU ATA211 System Manual
•
Route to FXS. If not answered within ring timer, answer the call, collect number & route as per
incoming call route selection: The system will place the incoming call on the FXO port to the FXS
port. The phone connected to the FXS port will start ringing for the duration of the Ring Timer (default:
45 seconds). If the call is not answered within the timer, ATA answers the call and gives dial tone to the
caller. When the caller dials the number, the system collects the digits and routes the call as per the
Incoming Call Route you select: SIP1, SIP2, SIP3 or Dialed Number Table.
If you select this option, select the Incoming Call Route. You may also configure the Ring Timer.
2. Enter the Fixed Destination Number in this field, if the incoming call routing option requires the call to be
finally placed to a fixed destination. You can configure the fixed destination number of maximum 40
characters. Default: Blank
3. You need to configure this parameter, only when the Incoming Call Routing option you selected requires
the Incoming Call Route to be selected. You can select:
•
SIP1/SIP2/SIP3: Select SIP1/SIP2/SIP3 as the Incoming Call Route, if you want to route the incoming
call received on FXO port using SIP1/SIP2/SIP3 trunk.
•
Dialed Number Table: Select option as Incoming Call Route, if you want ATA to route the incoming
call on the basis of the ‘number’ dialed. ATA will match the dialed number with the Dialed Number
Table. If the number matches, the destination route corresponding to the number will be used for call
routing. If you select this option, you must configure the Dialed Number Table.
To do this,
• Click the arrow icon. The Dialed Number Table opens in a new window.
Matrix SETU ATA211 System Manual
39
•
For each index number,
•
Enter the desired Number (max. 24 characters) you want to store in the table.
The first Index number 001, is reserved for No Match Found. Start your entries from Index 002.
•
For the number you entered, define the Minimum Digits, which the system should wait to
receive before considering it as a valid number. Default:01
•
For the number you entered, define the Maximum Digits, which the system should wait to
receive before considering it as End of Dialing. Default: 24
•
For the number you entered, select as Destination Route the SIP Trunk / FXS port/ FXO port.
At the bottom of the table, select Destination Route for dialed numbers that do not
match with any of the entries configured in this table (No Match Found) by the
Source Port.
40
Matrix SETU ATA211 System Manual
•
•
For calls made from the FXS port, select the destination route for the option If dialed number
does not match with either of the programmed number in the Dialed Number Table & call
is made from FXS, route the call through. Default: SIP Trunk 1.
•
For calls made from the FXO port, select the destination route for the option If dialed number
does not match with either of the programmed number in the Dialed Number Table & call
is made from FXO, route the call through. Default: SIP Trunk 1.
Click Submit and close the window. To know more see “Dialed Number Table”.
4. Enter the time duration in the Ring Timer field, for which the ring should be played on the FXO Port for an
incoming call. Range of the ring timer is of 01 to 99 seconds. Default: 45 sec.
5. If you want to Authenticate Incoming Calls on FXO port, that is you want to allow incoming calls only
after callers have authenticated themselves, enable PIN Authentication. Default: Disabled.
You must configure the PIN Authentication Table. To do this,
• Click the arrow icon.
Matrix SETU ATA211 System Manual
41
•
The PIN Authentication Table page opens in a new window.
•
Enter the PIN to be authenticated against each Index in the Table.
PIN number can be a of maximum 4 digits. The characters allowed are: 0-9,*, #
•
•
If you have finished entering, click Submit.
Close the window.
To know more about this feature, see “PIN Authentication”.
42
Matrix SETU ATA211 System Manual
Advanced
1. ATA uses Answer Supervision signaling to indicate to the FXS port that the call made through the FXO
port has been answered by the remote party.
Answer Supervision is used in the application where a PCO machine is connected to the FXS port of
ATA211. This signalling is used to indicate the event of call maturity (when the called party has gone Offhook) so that the PCO machine can start billing.
In absence of this signal, the call will not be considered as matured by the ATA, even when the called party
goes Off-hook. This will result in no billing.
Select the appropriate Answer Supervision Type from the options according to the type supported by
your CO network:
•
None: This option is to be selected when no signaling is available from the CO. If this option is
selected, the call will be considered as matured on the expiry of the 'Forced Maturity Timer'
(programmable; default: 15 seconds), irrespective of whether the call gets matured or not. After this
timer, the system will start detection of Disconnect signal or Tone programmed on the FXO port.
When the Answer Supervision type is selected as None, configure the Forced Maturity Timer. The
range of this timer is from 00 to 99 seconds. Default: 15 seconds.
•
Polarity Reversal: If this option is selected, ATA will consider the call as matured only if reversal of
polarity is detected on the FXO port. Forced Maturity Timer will not be applicable in this case.
Default: None.
2. Disconnect Signaling is used in the application where a PCO machine is connected to the FXS port of
ATA211. This signalling is used to indicate the event of call disconnection (when the called party has gone
On-hook) so that the PCO machine can stop billing.
Matrix SETU ATA211 System Manual
43
In the absence of this signal, the call will not be considered as disconnected, even when the caller goes
On-hook. This will result in inaccurate billing.
To resolve this, ATA211 supports 'Disconnect Signaling Detection'. When there is an outgoing call through
the FXO port or there is an incoming call on the FXO port, and call gets matured, if the called party
disconnects the call, the disconnect signal will be generated.
Select the appropriate Disconnect Signaling Type from the options according to the type supported by
your CO network:
•
None: Select this when no signaling is available from the CO.
•
Polarity Reversal: Select this when call disconnection is signaled in the form of Polarity Reversal.
When the call is disconnected by the remote user, the polarity of line gets reversed, the FXO port is
released (free) and caller gets error tone.
•
Open Loop Disconnect: Select this option when call disconnection is signaled in the form of Open
Loop Disconnect signal. ATA211 will check Open Loop Disconnect signal for the time configured as the
Open Loop Disconnect Timer.
If Open Loop signal is detected for the time less than the Open Loop Disconnect Timer configured, it
will not be considered as a valid Open Loop signal for releasing the port. If Open Loop is detected
continuously at least for the time set in the Open Loop Disconnect Timer, it is considered as a valid
Disconnect signal. After this signal is detected, the call will be released and caller will get error tone.
If you select this option, you must configure the Open Loop Disconnect Timer.
•
Open Loop Disconnect Timer: If you selected Open Loop Disconnect, you may set the value of
this timer, as required. Default: 500 milliseconds. Valid range: 001 to 999 msec.
Default: None
3. Disconnect Tone Detection is used by ATA to release the FXO port, when the remote party goes On-
hook or disconnects the call. The tone detection is applicable for both incoming and outgoing calls made
on/ from the FXO port. Consider this example:
IP
WAN Port
SETU ATA211
PSTN
FXO
FXS
Calling Party (X)
Calling Party (Y)
As shown in above the figure, the Extension-X is in an active call with remote party 'Y'.
Now, during the call, when remote party 'Y' goes On-hook, but the PSTN does not send any disconnect
signal as an indication of On-hook, party 'X' will not know this and remain Off-hook, even after party-Y has
gone On-hook.
44
Matrix SETU ATA211 System Manual
In such cases, if the PSTN sends some signaling in the form of Disconnect Tone, and if this is detected
by ATA211, ATA can use this to indicate to user 'X' that the remote party 'Y' has gone On-hook, to
disconnect the call.
•
Keep the Disconnection Tone Detection check box to if you want ATA to detect Disconnect Tone of
the PSTN. Default: Enabled.
•
In the Disconnect Tone ON Time and Disconnect Tone OFF Time fields, set the Disconnect Tone
Cadence as supported by the PSTN. Default: 0750 msec.
Ask you exchange for the details of Disconnect Tone's ON Time and OFF Time (Cadence).
4. Select the Automatic Number Translation check box, if you want to apply this feature on the FXO port.
Default: Disabled.
Automatic Number Translation (ANT) enables you to modify or translate the dialed number into another
number. ANT is useful when you need to modify or replace a few digits of the dialed number with other
digits, before the system dials out the number.
To apply ANT on the FXO port, you must enable ANT and configure the Automatic Number Translation
Table with dialed numbers and substitute numbers. To do this,
•
Make a list of numbers that need to be modified before being dialed out from the FXO port. Make a list
of the corresponding modified numbers that the system should substitute the dialed numbers with.
•
Click the arrow icon.
Matrix SETU ATA211 System Manual
45
•
The Automatic Number Translation table opens in a new window.
In this table, you can store as many as 24 Dialed Numbers and their corresponding Substitute
Numbers, at Index Numbers 01 to 24.
•
In the Dialed Number column, enter the numbers that need to be modified when dialed out from the
FXO port.
•
In the Substitute Number column, enter the numbers which the system should dial out in place of the
dialed numbers.
Make sure you enter a Dialed Number and its corresponding Substitute Number at the same Index
number in the table. For example, if you entered 001 as Dialed Number at Index 01, you must enter its
corresponding Substitute Number 1 also at Index 01.
•
Click Submit to save your entries.
•
Close the window.
5. Select the CLI Type from the options according to the type supported by your CO network:
•
•
•
DTMF
FSK, during ring
FSK, before ring
Default: DTMF
6. Select the appropriate Dial Type option as supported by your CO Network. You can select either Pulse or
Tone. Default:Tone
7. If you have selected the Dial Type as Pulse, you must set the Pulse Dial Ratio as per your country. You
can select the required pulse dial ratio from the following options: 40:60, 50:50 and 33:67. Default: 50:50.
46
Matrix SETU ATA211 System Manual
8. Configure the Flash Timer, as per your requirement. The Flash timer signifies the time period for which the
loop current breaks. SETU ATA211 uses this event to activate various features such as Call Hold, Call
Transfer, etc. Default: 600 msec.
9. You may configure the Ring Cadence-OFF Timer for the FXO port to set OFF time for Ring cadence.
During an incoming call on the FXO port, if the CO gives ring with a long Ring OFF period, the system will
consider that the ring has been stopped, and it will stop ringing the FXS port, even though the incoming
call is still present.
To get correct indication, the ATA211 supports the Ring Cadence OFF timer on the FXO port so that ring
can continue, even for incoming calls with long Ring OFF period.
The range of the Ring Cadence OFF timer is from 1 to 9 seconds. Default: 4 seconds.
10. In the DTMF On Time field, set the time as per the CO network. The DTMF On Time is the time for which
the DTMF digit which is to be out dialed remains ON. Valid range: 70 msec to 200 msec. Default: 70 msec.
11. In the DTMF Off Time field, set the time for which system should wait before dialing the successive DTMF
digits so that the CO network can detect the dialed digits. The DTMF Off Time may be 100 or 150 or 200
milliseconds. Default: 100 milliseconds.
12. Configure the Pause Timer to add delay, while a call is being made from FXO Port. ATA adds some delay
before dialing out the number after FXO Port goes Off-hook. During this time, no digit is dialed by the ATA
on FXO Port. This is used when exchange takes some tome to detect that FXO Port is Off-hook. Valid
range: 1 to 9 sec. Default: 1 sec.
13. Configure the FXO Busy Wait Timer, if you want SETU ATA211 to wait before routing a call to a busy FXO
port.
When there is an incoming call on a SIP trunk to be routed to the FXO port, and the FXO port is busy, you
can set the FXO Busy Wait Timer. SETU ATA211 will wait for the duration of this timer to route the call.
When the FXO port is free, it routes the call to the FXO port. The range of this timer is 00 to 99 sec.
Default: 45 sec.
14. To improve quality of speech, keep the Echo Cancellation3 check box enabled. Default: Enabled.
Also define the Tail Length depending on the length of the echo. Valid Range: 8 msec to 32 msec.
Default: 32 msec.
15. Select the appropriate AC Impedance according to the AC Impedance supported by the CO Network or
the PBX connected to the FXO port of SETU ATA211. You may select from the following impedance
options:
• 600 
• 900 
• 270  + (750  || 150 nF)
• 220  + (820  || 115 nF)
• 370  + (620  || 310 nF)
• 320  + (1050  || 230 nF)
• 350  + (1000  ||110 nF)
• 200  + (680  || 100 nF)
3. Echo Cancellation is a technique that allows isolation and filtering of unwanted signals caused by echoes during speech.
Matrix SETU ATA211 System Manual
47
•
•
•
•
•
600  + 2.16 µF
900  + 1 µF
900  + 2.16 µF
600  + 1 µF
Global complex impedance
Default: 600 
16. If required, you may adjust the Speaking Volume (Transmit) on the FXO port to increase or decrease the
volume of your voice being transmitted to the remote party. Select the appropriate Speaking Volume from
the drop-down list. Default: 0 db.
17. You may also adjust the Listening Volume (Receive) on FXO port to increase or decrease the volume of
the calling party's voice being transmitted to you. Select the required Listening Volume level from the dropdown list. Default: 0 db.
18. Click Submit to save the settings.
48
Matrix SETU ATA211 System Manual
FXS Port
SETU ATA211 supports an FXS port. Depending upon your requirement, you can either connect an standard,
analog telephone instrument to the FXS port, or interface the FXS port with the FXO port of a PBX.
To configure the FXS port parameters,
1. Click FXS.
2. Click More button to view all FXS port parameters on this page.
General
1. By default Call Routing is enabled on the FXS port.
You may disable the FXS Port and if you do not want to include it in Call Routing.
Matrix SETU ATA211 System Manual
49
2. You can assign a Name to the FXS port, which will be displayed to the called party (if the instrument of the
called party supports display name functionality).
The name you assign may consist of a maximum of 24 characters. Default: Blank
3. You can assign a Number to the FXS port. In case of Peer to Peer calls this number will be displayed to
the called party.
The length of the number string may have a maximum of 24 characters. Default: Blank.
Outgoing Calls
1. Select an appropriate Outgoing Call Routing option on the FXS port. Default: Route all calls from SIP1.
50
•
Select Don't allow outgoing calls, if you do not want to route calls through the FXS port.
•
Select Route all calls from SIP1, if you want all outgoing calls from the FXS port to be routed through
SIP Trunk 1.
•
Select Route all calls from SIP2, if you want all outgoing calls from the FXS port to be routed through
SIP Trunk 2.
•
Select Route all calls from SIP3, if you want all outgoing calls from the FXS port to be routed through
SIP Trunk 3.
•
Select Route all calls from FXO, if you want all outgoing calls from the FXS port to be routed through
the FXO port.
•
Select Route all calls as per Dialed Number Table, if you want specific numbers to be routed though
specific SIP Trunks only. If you select this option, you must configure the Dialed Number Table. To do
this,
Matrix SETU ATA211 System Manual
•
Click the arrow icon. The Dialed Number Table opens in a new window.
In this table, entries are stored at Index numbers from 002 to 100. For each index number,
•
Enter the desired Number (max. 24 characters) you want to store in the table.
•
For the number you entered, define the Minimum Digits, which the system should wait to receive
before considering it as a valid number. Default:01
•
For the number you entered, define the Maximum Digits, which the system should wait to receive
before considering it as End of Dialing. Default: 24
•
For the number you entered, select as Destination Route the SIP Trunk the system should use to
call the dialed number. Default: SIP 1.
•
At the bottom of the table, select Destination Route for dialed numbers that do not match with any of
the entries configured in this table, i.e.No Match Found.
Matrix SETU ATA211 System Manual
51
For calls made from the FXS port, select the destination trunk for the option If dialed number does
not match with either of the programmed number in the Dialed Number Table & call is made
from FXS, route the call through. Default: SIP Trunk 1.
For calls made from the FXO port, select the destination trunk for the option If dialed number does
not match with either of the programmed number in the Dialed Number Table & call is made
from FXO, route the call through. Default: SIP Trunk 1.
•
Click Submit and close the window.
To know more, see “Dialed Number Table”.
2. If you want to Authenticate Outgoing Calls from the FXS port only after users have authenticated
themselves with their PIN, enable the PIN Authentication check box. Default: Disabled.
If you enable PIN Authentication, you must configure the PIN Authentication Table. To do this,
• Click the arrow icon.
•
The PIN Authentication Table page opens in a new window.
•
Enter the PIN to be authenticated against each Index in the Table.
PIN number can be of a maximum of 4 digits. The characters allowed are: 0-9,*, #.
52
Matrix SETU ATA211 System Manual
•
If you have finished entering, click Submit to save.
•
Close the window.
To know more about this feature, see “PIN Authentication”.
3. Select the Auto PSTN Fallback check box, if you want ATA to automatically route the calls through the
FXO port when the internet (ethernet) link is down and the SIP trunks cannot be used for call routing.
Default: Disabled.
Class of Service
1. Select the features of SETU ATA211 that you want to allow in Class of Service4 (CoS) of the FXS port.
SETU ATA211 offers the following set of features in Class of Service:
• “Call Hold”.
• “Call Waiting”.
• “Call Transfer”.
• “Conference”.
• “Call Forward”.
• “Call Hold”.
• “Call Toggle”.
• “Do-Not-Disturb”.
By default all the features are enabled.
You may disable the feature you do not want to allow to the FXS port.
4. Class of Service (CoS) defines the set features of SETU ATA211 that the phone connected to the FXS port is to be allowed access to.
Matrix SETU ATA211 System Manual
53
Advanced
1. Select the appropriate Answer Signaling Type on the FXS port.
Answer Signalling is required when SETU ATA211 has a PCO/Billing machine connected on its FXS port.
When a call is made through SETU ATA211 and the called party answers the call, call maturity signal must
be generated on the FXS port of SETU ATA211 so that the PCO/Billing device connected to its FXS port
can start billing. In the absence of maturity information on the FXS port, the call will not be considered as
matured, resulting in inaccurate billing.
•
Select None, if no answer signaling is to be generated on the FXS port.
•
Select Polarity Reversal, if answer signaling is to be generated in the form of Polarity Reversal on the
FXS port.
Default: Polarity Reversal.
2. Select the appropriate Disconnect Signaling Type on the FXS port.
If a PCO machine is connected to the FXS port of the SETU ATA211, whenever the Called Party (remote
party) disconnects, the FXS port of SETU ATA211 needs to be informed of this event in the form of a
signal, so that the PCO machine can consider the call as complete and stop billing. In the absence of such
a signal, the call will be considered as completed only when the Caller goes On-hook, resulting in
inaccurate billing.
•
Select None, if no signaling is to be generated on FXS for call disconnection.
•
Select Polarity Reversal, if call disconnection is to be signaled in the form of Polarity Reversal.
•
Select Open Loop Disconnect, if call disconnection is to be signaled in the form of Open Loop
Disconnect signal.
If you select this option, you must configure the Open Loop Disconnect Timer.
54
Matrix SETU ATA211 System Manual
Default: Polarity Reversal.
•
Open Loop Disconnect Timer: If you selected Open Loop Disconnect, you may set the value of
this timer, as required. Default: 500 milliseconds.
3. Select the Subscriber Type for SETU ATA211. Default: Gateway.
When SETU ATA211is interfaced with a service provider server—ITSP, the Matrix ETERNITY IP-PBX, or
any other PBX—that supports supplementary services that require dialing of Flash, like Call Hold, Call
Transfer, Call Waiting, etc., you must select the Subscriber Type for SETU ATA according to the extent of
feature access you want on the FXS port connected to system.
•
Select Network, if you want to use the supplementary services supported by the PBX. When you set
SETU ATA211 in the Network mode, you can access the service provider features by dialing flash. You
will not be able to access the local features of SETU ATA211.
•
Select Gateway, if you want to use the supplementary features of SETU ATA211 primarily. In the
Gateway mode, you will also be able to access the supplementary services of the service provider
which required the dialing of Flash. See “Supplementary Services of Service Provider”.
4. Select the appropriate CLI Type according to the CLI Type supported by the telephone instrument
connected to the FXS port.
SETU ATA211 supports 3 signaling protocols for CLI on the FXS port:
•
•
•
DTMF
FSK-BellCore
FSK-ITU V.23
Default: FSK-ITU V.23
5. Configure the Flash Timer, as per your requirement. The Flash timer signifies the time period for which the
loop current breaks. SETU ATA211 uses this event to activate various features such as Call Hold, Call
Transfer, etc. Default: 600 msec.
6. To improve quality of speech, keep the Echo Cancellation5 check box enabled. Default: Enabled.
Also define the Tail Length depending on the length of the echo. Valid Range: 8 msec to 32 msec.
Default: 32 msec.
7. Select the appropriate AC Impedance according to the AC Impedance supported by the device connected
to the FXS port of SETU ATA211. The device may be a phone or a PBX. You may select from the following
impedance options:
• 600 
• 900 
• 270  + (750  || 150 nF)
• 220  + (820  || 115 nF)
• 370  + (620  || 310 nF)
• 320  + (1050  || 230 nF)
• 350  + (1000  || 210 nF)
• 200  + (680  || 100 nF)
• Default = 600 
5. Echo Cancellation is a technique that allows isolation and filtering of unwanted signals caused by echoes during speech.
Matrix SETU ATA211 System Manual
55
8. If required, you may adjust the Speaking Volume (Transmit) on the FXS port to increase or decrease the
volume of your voice being transmitted to the remote party. Select the appropriate Speaking Volume from
the drop-down list. Default: 0 db.
9.
You may also adjust the Listening Volume (Receive) on FXS port to increase or decrease the volume of
the remote party's voice being transmitted to you. Select the required Listening Volume level from the
drop-down list. Default: 0 db.
10. If you have completed the configuration of FXS port, click Submit to save settings.
56
Matrix SETU ATA211 System Manual
Passwords
The system can be programmed by the Administrator or the User, by logging into Jeeves as Admin or User with
their respective Passwords.
The default Admin and the default User Password are the same, 1234.
Since the Admin Login gives the you access to configure all the parameters of SETU ATA211, while the User login
has access to only user specific parameters, you may change the default password and use different Passwords
for Admin and User Login.
The password must not exceed 4 digits. Only the digits 0 to 9 are allowed.
Changing Admin Password
You can change the Admin Password only from Jeeves.
1. Log in as Admin with your Password.
2. Click the link Basic Settings on the left pane to expand.
3. Click Passwords.
4. In the Admin Password,
5. Enter the current password in the Old Password field.
6. Enter the new password in the New Password field.
7. Type the new password again for confirmation in the field Re-Enter to Confirm.
8. Click Submit to save.
Matrix SETU ATA211 System Manual
57
When you change the Admin Password, you will be logged out of Jeeves.
Restoring Default Admin Password?
In case you forget the Admin password, you must set the password to the default value. To do this,
1. Lift the handset of your phone.
2. Dial #***
You will get dial tone after successful execution.
3. Replace handset.
The Admin password will be set to the default value, if the option ‘Default Admin Password when User
defaults the ATA? is enabled in the System Parameters. To avoid this, make sure you disable this option
in the “System Parameters”.
Changing User Password
You can change the User Password only from Jeeves.
To change User Passwords from Admin Mode:
1. Log in as Admin.
2. Click the link Basic Settings on the left pane to expand.
3. Click Passwords.
58
Matrix SETU ATA211 System Manual
4. In User Password,
5. Enter the new password in the New Password field.
6. Type the new password again for confirmation in the Re-Enter to Confirm field.
7. Click Submit to save.
To change User Passwords from User Mode:
1. Log in as User.
2. Click the link User Settings on the left pane to expand.
3. Click User Password,
4. Enter the current password in the Old Password field.
5. Enter the new password in the New Password field.
6. Type the new password again for confirmation in the field Re-Enter to Confirm.
7. Click Submit to save.
Restoring Default User Password
The User Password is automatically set to the default value whenever you reinstate factory defaults in the system.
If you want to avoid having to set the entire system configuration to default settings, you may dial the related
system command from your phone.
To restore default User Password,
1. Lift the handset of your phone.
2. Dial #***
You will get dial tone after successful execution.
Matrix SETU ATA211 System Manual
59
3. Replace handset.
Dialing this command string will also reset the Admin Password to factory default, if the option ‘Default
Admin Password when User defaults the ATA? is enabled in the System Parameters. To avoid this,
make sure you disable this option before you default the User Password.
60
Matrix SETU ATA211 System Manual
Network Parameters
1. Click Network.
2. Click More button to view all Network parameters on this page.
Routing Mode
•
Select Routing Mode, according to your installation scenario as NAT or Bridge. Default: NAT.
•
Select NAT as Routing Mode, if the LAN and WAN port of SETU ATA are in different network
segments.
Matrix SETU ATA211 System Manual
61
•
You will need to configure NAT as Routing Mode, when the SETU ATA211 is at the edge of the network
and multiple hosts are connected behind ATA, and you want to share a common internet connection
between all hosts.
Select Bridge as Routing Mode, if the LAN and WAN port of SETU ATA are in the same network
segment.
Selecting Bridge mode will disable Network Address Translation (NAT) on the WAN port.
When you set SETU ATA211 in Bridge Mode, you need not configure the LAN port IP Address and Subnet
Mask. The WAN and the LAN port of SETU ATA211 can be accessed with the IP Address of the WAN port.
LAN
The LAN port of SETU ATA211 is used for connect a standalone computer or a LAN Switch.
If you need to change the IP Address or the Subnet Mask of the LAN Port of SETU ATA211, you may do so now.
Default IP Address of the LAN Port is: 192.168.002.006
Default Subnet Mask of the LAN Port is: 255.255.255.0
62
Matrix SETU ATA211 System Manual
WAN
1. Select the Connection Type according to the IP addressing scheme of the network which SETU ATA211
is connected: DHCP, PPPoE, and Static.
•
Select DHCP, if the network uses a DHCP server to assign the IP address, Subnet Mask and Gateway
address to SETU ATA211.
•
Select PPPoE, if the network uses PPPoE.
Enter PPPoE User ID (max. 40 characters) and Password (max. 24 characters). You may also enter
the PPPoE Service Name (max. 24 characters), if provided.
•
Select Static, if you want to assign manually assign the IP address, Subnet Mask and Gateway
address manually.
If you selected Static, enter the Static IP Address (default: 192.168.001.151) and the Subnet Mask
(default: 255.255.255.0), and the Gateway Address.
By default, the Connection Type for the WAN port is Static. IP Address: 192.168.001.171, Subnet
Mask: 255.255.255.0
Matrix SETU ATA211 System Manual
63
DNS Server
DNS stands for Domain Name Server which is used to resolve domain name into IP address. You can select either
Static or Automatic. Default: Static.
1. Select Static if you want to configure DNS manually.
•
Enter Primary DNS Address.
•
Enter Secondary DNS Address, if available.
Secondary DNS Address will be considered when the request to Primary DNS server fails.
•
Enter the DNS Domain Name.
2. Select Automatic DNS if you want DNS Address and Domain name to be assigned by the DHCP/PPPoE
server automatically.
This option will be applicable only if you have enabled DHCP or PPPoE as connection type.
64
Matrix SETU ATA211 System Manual
Advanced
1. If the SETU ATA211 is connected in VLAN network, configure the VLAN/CoS.
This parameter enables the SETU ATA211 to add VLAN header to the packets generated by it. The VLAN
header consists of the VLAN ID (12-bit) and Class of Service (CoS, 3-bit) for prioritization of traffic6.
•
Select the VLAN/CoS check box to enable VLAN ID tagging on all packets generated by the system.
Default: Disabled.
•
Enter the VLAN ID that you have assigned to the VLAN in which the SETU ATA211 is connected. The
valid range for this is 0-4094. Default: 0001.
•
For SIP CoS, define the CoS (priority) bits which will be added in all SIP packets. The range of CoS bits
is from 0 to 7. Default: 3
•
For RTP CoS, define the CoS (priority) bits which will be added in all RTP packets. The range of CoS
bits is from 0 to 7. Default: 6.
2. SETU ATA211 will send all SIP messages using SIP QoS setting, enter the SIP DiffServe/ ToS as per
your requirement.Valid range is from 00-63, Default: 26
6. The IEEE 802.1P standard allows Layer2 switches to prioritize the traffic, thus providing Quality of Service (QoS), i.e. better handling
of data that pass over a network, thereby resulting in greater reliability and quality. Quality of Service (QoS) on Layer2 is referred to as
Class of Service (CoS) which is defined by IEEE 802.1P.
Matrix SETU ATA211 System Manual
65
3. SETU ATA211 will send all the RTP packets with RTP QoS setting, enter the RTP DiffServe/ ToS as per
your requirement. Valid range is from 00-63, Default: 46
4. MAC address selection provides you two options: Unique and Clone. Default: Unique MAC Address.
If you select Unique MAC Address, the system will use the unique MAC address assigned to it as source
MAC address on all Ethernet frames.
Select Clone MAC Address, if you want the system to use MAC address other than unique MAC address.
If you select Clone MAC Address, enter the desired MAC address manually in the Clone MAC Address
field. MAC address is in hexadecimal format, e.g. 00:50:c2:55:b0:10.
5. SETU ATA211 has an embedded web server called Jeeves, for system configuration. You may change the
Web Server Port as per your requirement. Valid range of the port is: 80, 1024-65535. Default: 80
6. SETU ATA211 has an embedded FTP server for Software Upgrade. You may change the FTP Server
Port as per your requirement. Valid range is 21, 1024-65535.Default: 21
7. After you have set all the parameters as per your requirement, click Submit at the bottom of the page.
8. You will get a prompt, 'This will restart the system, do you want to continue?'
9. Click OK to save the settings.
The system will restart.
66
Matrix SETU ATA211 System Manual
CHAPTER 5
Advanced Settings
Advanced Settings include the features and facilities listed below:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
System Parameters
Called Party Number Table
Dialed Number Table
Peer-to-Peer Numbers
Digest Authentication
Daylight Saving Time
Static Routing
Factory Defaults
Restart
Syslog
PCAP
Software Upgrade
Auto-Configuration
System Parameters
Certain parameters of SETU ATA211 are applied system-wide and are not specific to a port. These parameters are
called System Parameters.
To configure System Parameters,
1. Log into Jeeves as Admin with your password.
2. Click Advanced Settings on the left pane to expand the links.
Matrix SETU ATA211 System Manual
67
3. Click the link System. The System Parameters page opens.
4. You may configure the following parameters on this page, as required:
General
68
Matrix SETU ATA211 System Manual
•
System Name: You can assign a name to SETU ATA211, as 'System Name'. This name has significance
when multiple SETU ATA211 are connected in the same LAN network.
The Name you assign may contain a maximum of 24 characters. Default: Matrix SETU ATA211
•
First Digit Wait Timer: The First Digit Wait Timer signifies the time for which the system waits for
receiving the first digit after going Off-hook from the FXS Port. On expiry of this timer, the system will give
error tone to the user. Valid range: 01 to 99 seconds. Default: 15 seconds.
•
Inter Digit Wait Timer: Inter Digit Wait Timer signifies the time period for which the system should wait
between two consecutive digits when receiving the digits from the FXS Port. On expiry of this timer, the
number is considered to be complete and is dialed. Refer topic “Dialed Number Table” for information
about End of Dialing while dialing minimum or maximum numbers. Valid range: 01 to 99 seconds. Default:
5 seconds.
•
Transfer Notification Timer: This is the time for which the system will wait for notification of the status of
a transferred call, i.e. whether the transfer target is busy, has answered, has disconnected, etc. Refer topic
“Call Transfer” to know more. Valid Range: 01-99 secs. Default: 60 seconds
•
Play Routing Tone: By default, the system plays routing tone when the call initiated from the FXS / FXO
port is being routed through a SIP Trunk.
SETU ATA211 plays routing tone to the FXS / FXO port user when call is made through the SIP trunk.
You may clear the Play Routing Tone check box, if you do not want the system to play routing tone.
•
Call Release Timer: This timer allows the system to release the matured calls made from the FXS port,
FXO port and from SIP trunks after a specified time period.
The Call Release Timer is used for disconnecting calls that remain connected in certain conditions. For
example, the FXS port has disconnected the call, but no disconnect event is received from the SIP trunk.
In this case, the call remains live in the system. On the expiry of the Call Release Timer, this call will be
disconnected.
This Timer may also be used to restrict the duration of calls made from the FXS port, FXO port and SIP
trunks.
To apply this timer, select the Call Release Timer check box and set the Timer to the required duration
from 001 to 999 minutes. Default: 999 Minutes.
•
VoIP Silence Disconnect Timer: This feature allows disconnecting the call if silence is detected during
speech, for more than the specified duration.
The SETU ATA211 supports this feature to detect the silence during VoIP calls. If this silence duration
exceeds the specified value, the call will be disconnected.
To apply this timer, select the VoIP Silence Disconnect Timer check box and set the Timer to the
required duration from 001 to 99 minutes. Default: 99 Minutes.
•
Forward Error Correction: Forward Error Correction is used for data transmission whereby ATA211 adds
redundant data to its messages, which allows the receiver to detect and correct errors without asking the
sender for additional data.
Matrix SETU ATA211 System Manual
69
Select the Forward Error Correction check box to enable. Default: Disabled.
•
Voice Activity Detection: Voice Activity Detection is a software application which allows data network,
carrying voice traffic over the internet, to detect the absence of audio and conserve bandwidth by
preventing the transmission of 'Silent Packets' over the network.
Select the Voice Activity Detection check box if you want SETU ATA211 to apply Voice Activity Detection
(also called ‘Silence Suppression'). Default: Disabled.
•
Default 'Admin' password when 'User' defaults the ATA?: When SETU ATA211 is set to factory
defaults, the Admin Password not be set to default, unless this flag is enabled.
By default the option Default 'Admin' Password when 'User' defaults the ATA? is enabled, clear the
check box to disable. Default: Enabled
If you are an ITSP, you may use this flag (disable) to prevent your customers (end users) from setting the
Admin Password to default and gaining unrestricted access to system configuration.
NAT
•
STUN (Simple Traversal of UDP through NAT) server facilitates traversing through most NATs, except
symmetric NATs. So, if your router has Symmetric NAT, do not configure STUN.
If your SETU ATA211 is located behind a NAT router that is other than symmetric,
•
in the STUN Server Address: Port field, enter the STUN Server Address and the Listening Port of the
STUN Server.
The STUN Server Address can have a maximum of 40 characters.
The valid range of the STUN Server Port is from 1024–65535. Default: 03478.
•
Clear the SIP Port fetched using STUN check box, if SETU ATA211 is located behind the NAT router
and you have forwarded the SIP listening port of the SETU ATA211 in the router.
Keep the SIP Port fetched using STUN check box enabled, if you have not forwarded the SIP
Listening Port in the router.
70
Matrix SETU ATA211 System Manual
Make sure you configure the NAT Type on the SIP Trunk as STUN. See “SIP Trunks”.
•
Router's Public IP Address: Routers public IP address specifies the public IP address of the NAT router
behind which system is located. Default: Blank.
You need to configure this field only if the system is located behind the NAT router and a Static IP Address
is assigned as Public IP Address of the Router.
Make sure you configure the NAT Type on the SIP Trunk as Router’s IP Address. See “SIP Trunks”.
•
UDP NAT Keep Alive: When SETU ATA211 is connected behind a NAT router and SIP messages are
transported over UDP, NAT Keep Alive messages must be sent to refresh the binding in the NAT router.
Select the UDP NAT Keep Alive check box to enable. Default: Disabled.
Select the type of Keep Alive Message to be sent. You may select either REGISTER or NOTIFY. Default:
NOTIFY.
As Interval, set the time period after which the system should send Keep Alive messages. This time period
should be less than the NAT binding timer of the router. The valid range for the UDP NAT Keep Alive
Interval is 001–999 seconds. Default: 120 seconds.
•
TCP NAT Keep Alive: When SETU ATA211 is connected behind a NAT router, and SIP messages are
transported over TCP, NAT Keep Alive messages must be sent to refresh the binding in the NAT router.
Select the TCP NAT Keep Alive check box, if you want the system to send Keep Alive messages
periodically to refresh the binding in the NAT router. Default: Disabled.
As Interval, set the time period after which the system should send Keep Alive messages. This time period
should be less than the NAT binding timer of the router. The valid range for the TCP NAT Keep Alive
Interval is 0001–9999 seconds. Default: 120 seconds.
SIP
Matrix SETU ATA211 System Manual
71
•
100rel/PRACK: This parameter is to be configured if you want to support reliable transmission of (SIP)
provisional responses over UDP.
Select the 100rel/PRACK Enable check box, if you want the SETU ATA211 to use 100rel SIP extension
for reliable transmission of SIP provisional responses and to use PRACK (Provisional Acknowledgement).
Default: Disabled.
•
SIP Over TCP: SETU ATA211 supports transporting of SIP messages over User Datagram Protocol
(UDP) as well as Transfer Control Protocol (TCP) connection. Despite the advantages that SIP over TCP
offers, it is more common to use UDP to transport SIP messages.
By default, SIP over TCP is enabled. If you want to receive SIP messages over TCP keep this option
enabled.
You must also enable ‘TCP' or 'TCP (Fallback to UDP)' on the “SIP Trunks”.
•
SIP UDP Port: This is the port on which the SETU ATA211 listens for SIP messages transported over
UDP. This port is also used as the source port for sending SIP messages to the remote peer. The valid
range for this port is 1024–65534. Default: 05060.
•
SIP TCP Port: This is the port on which the SETU ATA211 listens for SIP messages transported over TCP.
This port is also used as the source port for sending SIP messages to the remote peer. The valid range for
this port is 1025–65526. Default: 05060.
•
RTP Listening Port: This is the port on which the SETU ATA211 listens for RTP Packets. This port is also
used as the source port for sending RTP packets to the remote peer. The valid range for this port is
1024–65526. Default: 08000.
•
SIP INVITE Timer: This is the time in seconds for which SETU ATA211 waits for a response from the
called party after sending INVITE message. This timer starts after sending INVITE message to the called
party and stops on receipt of the provisional response or the final response or when the user disconnects
the call. On expiry of the timer, the SETU ATA211 terminates the call process and gives an error tone to
the user. The range of the SIP INVITE TIMER is 010–180 seconds. Default: 30 seconds.
•
SIP Provisional Timer: This is the time in seconds for which SETU ATA211 waits for final response after
receiving the provisional response from the called party. This timer starts on the receipt of the provisional
response from the called party and stops on receipt of the final response from the called party or when the
user disconnects the call. On expiry of the timer, the SETU ATA211 terminates the call process and gives
error tone to the user. The range of SIP Provisional Timer is 010–180 seconds. Default: 60 seconds.
•
General Request Timer: This is the time in seconds for which the SETU ATA211 waits for response of a
transaction request. This timer starts on initiating a transaction and stops on the receipt of a response for
the request. On expiry of the timer, the SETU ATA211 clears the transaction. This timer is used for
Registration request, etc. The range of the General Request Timer is 10–60 seconds. Default: 20 seconds.
5. Click Submit to save the settings.
72
Matrix SETU ATA211 System Manual
Called Party Number Table
Called Party Number Table is used for routing incoming calls on the SIP trunks on the basis of the Called Party
Number received, without answering the call.
You must configure this table, if you have selected Route as per called party number as the Incoming Call
Routing option for the SIP trunk.
In the Called Party Number Table, you can store a maximum of 10 numbers.
Each number is stored at an Index in the table. For each number that you enter in the table, you must define the
minimum and maximum digit length and select the desired port—FXS or FXO—to route the call.
Consider the following example of the Called Party Number Table:
Index Number
Minimum Digit Maximum Digit Destination Route
01
(No match found)
01
24
FXO
02
2
7
7
FXO
03
3
7
7
FXO
04
98
10
10
FXS
05
00
12
12
FXS
In this Table:
• The Called Party Number strings received in the incoming call are stored in the Number column against
Index 02 to 10. The first Index is reserved for the No Match Found Entry. The numbers may be prefixes
or the complete number strings.
•
For each number, the digit length is defined as Minimum Digit and Maximum Digit.
•
For each number, the port to be used for routing the call is selected as the Destination Route.
•
The incoming calls received from local numbers are to be routed through the FXO port. These are 7
digit numbers starting with ‘2’ or ‘3’. So, the prefixes of these numbers, '2' and ‘3’ are entered in the
Number field. The Minimum and Maximum Digits are defined as ‘7’. The Destination Route is selected
as FXO port.
•
Incoming calls from mobile numbers starting with ‘98’ are to be routed to the FXS port. Since the mobile
numbers are 10 digit numbers, the Minimum and Maximum digits are configured as ‘10’ and the
Destination Route is selected as FXS.
•
Twelve-digit International numbers starting with ‘00’, are to be routed through the FXO port. So, the
Minimum and Maximum digits are configured as ‘12’ and the Destination Route is selected as FXO.
When there is an incoming call and the incoming call routing option is selected as Route as per called party
number, the system will check the Called Party Number.
It will use the best match logic to match the number with the table. If the number received starts with ‘2’, the system
will match with the entry at Index02. The system will match the length of the digits with the minimum and maximum
configured for the entry at Index02. If the minimum and maximum digits match the system routes the call through
the FXO port selected as Destination Route for numbers starting with ‘2’.
Matrix SETU ATA211 System Manual
73
To be considered as a valid number, the number received must be equal to or more than the Minimum digits
configured. If the number received matches the Minimum digits but exceeds the maximum digits, the system will
strip off the extra digits and route the number.
If the incoming CLI does not match with any entry in Called Party Number Table (i.e. the number does not exist in
the table), the call will be routed through the destination route for the first entry at Index 001, i.e. the No Match
Found entry, in the table.
Configuring Called Party Number Table
If you have not already configured the Called Part Number Table for the SIP Trunk, you may do so now.
1. Login as Admin with your Password.
2. Click the link Advanced Settings on the left pane to expand.
3. Click Called Party Number Table.
The Called Party Number Table page will open.
4. For each Index Number,
•
Enter the desired Number you want to store in the table. The number must not exceed 24 characters.
The first Index Number 001, is reserved for No Match Found. Start your entries from Index 002.
74
•
For the number you entered, define the Minimum Digits, which the system must receive to consider it
as a valid number. Default:01
•
For the number you entered, define the Maximum Digits. The number received must not exceed the
maximum digits you have defined here. Default:24
Matrix SETU ATA211 System Manual
•
For the number you entered, select the Destination Route. It may be the FXS or FXO port to route the
Called Party number.
5. Click Submit save your entries.
Matrix SETU ATA211 System Manual
75
Dialed Number Table
The Dialed Number Table is a list of numbers or part numbers (you must configure), with a preferred SIP trunk /
FXO port / FXS port for each number. When the user dials a number from the FXS port, SETU ATA211 checks the
Dialed Number Table for a match using the best fit logic. If a match is found, it uses the Destination Route selected
for the number in the table to make the outgoing call.
In the Dialed Number table, upto 100 numbers can be stored.
Each number is stored at an Index in the table. For each number that you enter in the table, you must define:
• the minimum number of digits that the system should wait to receive to consider it a valid number to be
dialed out.
• the maximum number of digits which the system should wait to receive to consider it as “End of Dialing”
and dial out the number.
• the Destination Route (the SIP Trunk, FXO port or FXS port), which the system should use to dial out the
number.
The Dialed Number Table is to be configured only if you have selected:
• the Outgoing Call Routing option for the FXS port as Route all calls as per Dialed Number Table.
• the Incoming Call Route for the FXO port as Dialed Number Table.
When a number is dialed from the FXS port or received on the FXO port,
•
SETU ATA211 will match the dialed number with the entries of the Dialed Number Table.
•
If a match is found, it will check the Minimum Digits programmed for this entry to consider it a valid number.
If the length of the number string you dialed matches with the Minimum Digits programmed for this entry,
and “End of Dialing” is detected7, the system will consider it as a valid number. It will not wait to match it
with the Maximum Digits you configured for this entry. The system will dial out the number using the
Destination Route you have selected for this entry in the table.
However, if the number of digits dialed by you are less than the Minimum Digits you configured, you will get
error tone.
•
If the dialed number string exceeds the Minimum Digits, but is less than the Maximum Digits, the system
will check the Maximum Digits programmed for this entry.
•
If the length of the dialed number string equals the Maximum Digits programmed for this entry, the system
will not wait for further digits to be dialed. It will consider the Maximum Digits defined as End of Dialing, and
will dial out the number using the Destination Route you selected for this entry in the table.
•
You can configure the Destination Route for dialed numbers that do not match with the table by the Source
port.
•
•
•
If FXO port is the Source Port, you can route the call through — SIP1/SIP2/SIP 3, FXS.
If FXS port is the Source Port, you can route the call through— SIP1/SIP2/SIP3, FXO.
If you do not want dialed numbers that do not match with the table to be routed, select None.
7. You pressed the # key or the Inter Digit Wait Timer has expired. See “End of Dialing”.
76
Matrix SETU ATA211 System Manual
Configuring Dialed Number Table
If you have not already configured the Dialed Number Table for the FXS port, you may do so now.
1. Login as Admin with your Password.
2. Click the Advanced Settings link on the left pane to expand.
3. Click Dialed Number Table.
The Dialed Number Table page opens.
4. For each Index number,
•
Enter the desired Number you want to store in the table. The number must not exceed 24 characters;
all ASCII characters are allowed.
•
For the number you entered, define the Minimum Digits, which the system should wait to receive
before considering it as a valid number. Default:
•
For the number you entered, define the Maximum Digits, which the system should wait to receive
before considering it as End of Dialing. Default:
•
For the number you entered, select as Destination Route the port the system should use to call the
dialed number. Default: SIP 1
If no Destination Route is selected (‘None’) for an entry, the system will reject the call, even if a match
is found for the dialed number in this table.
Matrix SETU ATA211 System Manual
77
•
At the bottom of the table, select Destination Route for dialed numbers that do not match with any of
the entries configured in this table (No Match Found) by the Source Port.
•
For calls made from the FXS port, select the destination route for the option If dialed number does
not match with either of the programmed number in the Dialed Number Table & call is made
from FXS, route the call through. Default, SIP Trunk 1.
•
For calls made from the FXO port, select the destination route for the option If dialed number does
not match with either of the programmed number in the Dialed Number Table & call is made
from FXO, route the call through. Default, SIP Trunk 1.
5. Click Submit save your entries.
78
Matrix SETU ATA211 System Manual
Peer-to-Peer Numbers
Calls made between two IP clients without the intervention of a Proxy Server are defined as Peer-to-Peer Calls
(P2P calls). P2P call can be made from FXS or FXO port.
As the Peer-to-Peer call application does not require a SIP server, voice communication using this application is
done virtually free of cost. The major cost savings offered by this application makes it a very attractive mode of
inter-branch or intra-office voice communication.
Peer-to-Peer call applications can also be used by residential users for making overseas calls at no cost.
A maximum of 500 locations can be interfaced using ATA211.
To use this feature:
•
There must be a SETU ATA211 installed at each location.
•
The SETU ATA211 at each location must have a Static IP Address.
Let us take the installation scenario illustrated below as an example.
Location-B
Location-A
3001
2001
FXS
WAN
190.1.1.200
IP Network
Broadband
Modem/Router
ATA211
LAN
FXO
190.1.1.100
Broadband
Modem/Router
PSTN
WAN
FXS
ATA211
PSTN
•
At both locations ATA is directly connected to the IP network.
•
At each location, you must do the following configuration:
• enable a SIP trunk to be used for Peer-to-Peer calling.
• set the SIP Trunk Mode to Peer-to-Peer.
• configure the number callers must dial to reach this SIP trunk as its SIP ID.
• set the Incoming Call Routing option on the SIP trunk as Route to FXS.
• configure Outgoing Call Route on the FXS port.
• configure Incoming Call Routing on the FXO port.
• configure the Peer-to-Peer table.
FXO
LAN
The Peer-to-Peer table stores upto 500 entries. Each entry consists of the parameters Number, Name,
Minimum Digits, Maximum Digits and Destination Address.
•
In this example, you would have to configure the Peer-to-Peer table as follows:
•
At Location A, in the Number field of the Peer-to-Peer table, enter the Number you want to dial to
call the phone at Location B. In this case, 3001.
Matrix SETU ATA211 System Manual
79
•
For the number you entered, in the Destination Address field in the table, enter the IP Address of
the WAN Port of ATA connected at Location B. In this case, 190.1.1.100
•
For the number you entered, configure the digit length in the table. As the number you want to dial,
3001, has four digits, configure Minimum Digit for this number as ‘4’. Also configure the Maximum
Digit as ‘4’.
The Peer-to-Peer table you configure for SETU ATA211 at Location-A would look like this:
Index
Number
001
002
Name
Minimum Digit
Maximum Digit
No Match Found
01
24
3001
04
04
Destination Address
190.1.1.100
003
004
As the system uses the best match logic to match number strings in the Peer-to-Peer table, you
may configure only the prefix of the number to be dialed. Instead of the complete number string, you
may configure only the prefix as follows, the system will place all calls that start with ‘3’ to the IP
Address 190.1.1.100
Index
Number
001
002
Name
Minimum Digit
Maximum Digit
No Match Found
01
24
3
04
04
Destination Address
190.1.1.100
003
004
•
Similarly, the Peer-to-Peer table you configure at Location-B should look like this:
Index
Number
001
002
Name
Minimum Digit
Maximum Digit
No Match Found
01
24
2001
04
04
Destination Address
190.1.1.200
003
004
80
•
When user 2001 of Location-A or a caller on the FXO port calls 3001, the call is placed to the IP address
190.1.1.100 as the system finds a best match entry for the dialed number at index 002 of the Peer-to-Peer
table.
•
On receiving a call, the SETU ATA at Location-B routes this call to the FXS port, 3001.
•
Similarly, when the user 3001 of Location B or a caller on the FXO port, calls 2001, the call is placed to the
IP address 190.1.1.200 as the system finds a best match entry for the dialed number at index 002 of the
Peer-to-Peer table.
Matrix SETU ATA211 System Manual
Configuring Peer-to-Peer Calling
To use Peer-to-Peer calling, do the following:
• enable the SIP trunk.
• set the SIP Trunk Mode to Peer-to-Peer.
• configure the number callers must dial to reach this SIP trunk as its SIP ID.
• set the Incoming Call Routing option on the SIP trunk as Route to FXS.
• configure Outgoing Call Route on the FXS port.
• configure Incoming Call Routing on the FXO port.
• configure the Peer-to-Peer table.
If you have not configured the Peer-to-Peer table from the SIP Trunks page under Basic Settings, you may do so
now.
1. Log in as Admin.
2. Click the Advanced Settings link on the left pane to expand.
3. Click the Peer-to-Peer Numbers link. The Peer-to-Peer Table opens.
In the Peer-to-Peer table, each entry is stored against an Index Number from 001 to 500. The first entry at
Index001 is reserved for No Match Found.
4. For each Index number,
•
In the Number field, enter the peer-to-peer number string—prefix or entire number—that will be dialed.
The number string must not exceed 24 characters. Default: Blank.
Matrix SETU ATA211 System Manual
81
If the number to be dialed out is <dialednumber@destination address>, for example, 1234@abc.com,
you must enter 1234 in this field.
•
In the Name field, enter a name to identify the number string you configured. It may be the name of
your contact or any name you wish to assign to the number string. The name may consist of 24
characters (maximum). Default: Blank.
The name you configure here will not be used in SIP signaling.
•
As Minimum Digits, define the minimum length of the number string that must be dialed for the system
to consider it as a valid number. Default: 01.
•
As Maximum Digits, define the maximum length of the number string that must be dialed out for the
system to consider it the complete number string. Default: 24.
•
In the Destination Address field, enter the domain name or IP Address to where the call is to be
placed. The Destination Address may consists of up 40 characters (maximum). Default: Blank.
For example, if the peer-to-peer number to be dialed out is 1234@abc.com, enter abc.com as
Destination Address. If the number is 1234@ 192.168.1.197, enter 192.168.1.197 as the Destination
Address. The Destination Address can also be in the form of Address: Port number.
5. Click Submit to save your entries.
You may log out of Jeeves.
Making Peer-to-Peer Calls
To make a Peer-to-Peer Call:
•
Go Off-hook.
•
Dial the IP Address of the remote party or the number of the remote party stored in the Peer-to-Peer Table.
•
To dial an IP Address, press * key (star/asterisk).
For example, to call the IP Address 192.168.200.200, dial 192*168*200*200.
When you press the * key it is interpreted by the SETU ATA211 as a '.' (dot/period).
•
82
Talk, when the remote party answers the call.
Matrix SETU ATA211 System Manual
Digest Authentication
Digest Authentication is a challenge-based authentication service of SIP to authenticate the identity of the
originator of SIP request in the INVITE message. The recipient of the request can ascertain whether or not the
originator of the request is authorised to make the request. When the digest credentials of the originator—User
Name and Password—in the INVITE message are authenticated and accepted by the recipient, the originator and
the recipient are connected.
SETU ATA211 supports Digest Authentication. The Digest Authentication feature works on the basis of the Digest
Authentication Table, in which the credentials, namely the User Name and Passwords of trusted/authorised calling
party SIP devices are stored. You must configure this table.
When you enable this feature on a SIP trunk, for all incoming calls (SIP requests),
•
SETU ATA211 will challenge the identity of the calling party, i.e. the SIP device initiating the request to
send its digest credentials.
•
When the calling party sends its credentials, SETU ATA211 authenticates the credentials by matching it
with its Digest Authentication Table.
•
If a match is found, the calling party will be authenticated and the call will be allowed on the SIP trunk.
•
If no match is found, SETU ATA211 will consider it as invalid authentication information and reject the call.
You may use Digest Authentication to
• restrict access to SETU ATA211 to specific callers.
• prevent unwanted or malicious calls.
Let us understand Digest Authentication with the help of an example:
•
A Company has its head office in Mumbai and branch offices in the cities of Kolkata, Chennai and New
Delhi.
•
For voice communication over IP, the Company has installed SETU ATA211 in all its branches for making
Peer-to-Peer Calls.
•
The Company wants to use a SIP trunk for exclusively for inter-office calling.
•
To be able to do this, the Company must do the following in all its branch offices:
•
set the SIP Trunk mode of the desired SIP trunk to Peer-to-Peer mode, and configure Peer-to-Peer
Numbers8.
•
enable Digest Authentication on this SIP Trunk.
•
configure the Digest Authentication Table with the User Name and Password of the SIP devices of all
branches, from which calls are to be allowed on this SIP trunk. In this case, the User Name and
Password will be of the dedicated Peer-to-Peer SIP trunk in the branch offices. For example, In the
Digest Authentication Table you configure at the Mumbai office, you must configure the User Name
and Password for the dedicated SIP trunks at the offices in Kolkatta, Chennai and New Delhi. Similarly,
8. Static IP address is assigned to the WAN port of all Gateways and the SIP trunks are set to Peer-to-Peer mode in all the offices.
Matrix SETU ATA211 System Manual
83
in the Digest Authentication Table you configure in the New Delhi office, you must configure the User
Name and Password for the dedicated SIP trunks at the offices in Mumbai, Kolkatta, Chennai.
•
With Digest Authentication configured at all branches, whenever an incoming call is received on the
SIP trunk, the SIP trunk will challenge the identity of the caller. When the digest credentials sent by the
calling device matches with the Digest Authentication Table, the call will be allowed on the SIP trunk.
•
If the digest credentials do not match, the call will be rejected.
•
Thus the Company can use Digest Authentication to restrict all call except those from its branch offices
on a SIP trunk.
Configuring Digest Authentication
To use this feature, make sure you have enabled Digest Authentication on the desired SIP Trunk and configure
the Digest Authentication Table.
If you have not already configured the Digest Authentication Table on the SIP Trunk parameters page, you may do
so now.
1. Log in as Admin with your Admin Password.
2. Click the link Advanced Settings on the left pane to expand the links.
3. Click Digest Authentication.
The Digest Authentication Table page opens. You can configure upto 500 entries in this table. This Table
is common for all SIP trunks.
84
Matrix SETU ATA211 System Manual
•
Enter the user name assigned to the caller/calling device in the User ID field. SETU ATA211 will use this
User ID to match the digest credentials sent by the caller/calling devices when challenged.
Make sure the User ID you enter here and the User ID assigned at the calling end are the same. The User
ID can be up to 40 characters long. Default: Blank.
•
Enter the password to authenticate the user ID in the User Password field. The password may consist of
a maximum of 24 characters. Default: Blank.
Make sure the User Password you enter here and the User Password assigned at the calling end are the
same.
•
Click Submit to save the entries.
•
Now, enable Digest Authentication on the desired SIP Trunk. See “SIP Trunks” for instructions.
Matrix SETU ATA211 System Manual
85
Daylight Savings Time
Daylight Saving Time (DST) is the practice of advancing clocks so that afternoons have more daylight and
mornings have less. Typically clocks are adjusted forward one hour near the start of spring and are adjusted
backward in autumn. Many countries of the world9 use it, though the start and end dates of DST vary with location
and year.
SETU ATA211 supports Daylight Saving Time adjustment to set the Date and Time10 of SETU ATA211 forward and
backward according to the DST convention followed in your country.
You can set DST by: Day and Month or Date and Month.
When SETU ATA211 is set to default, your DST settings will remain unchanged.
Configuring DST
1. Log in as Admin.
2. Click the Advanced Settings link on left pane to expand the links.
3. Click Daylight Saving Time link.
4. Select the Daylight Saving Time Enable check box. Default: Disabled.
5. Enter the Time Offset. This is the time which the system will consider to forward the clock at the start of
DST and to set the clock back when DST ends. Default: 60 minutes
6. Select the desired Type of DST as:
9. In most countries in Asia and Africa, and in certain countries of South America, DST is not observed.
10. SETU ATA211 sets its Date and Time according to the Time Zone you selected, and synchronizes the time according to the NTP
Server you selected. See “Region”.
86
Matrix SETU ATA211 System Manual
•
Day-Month Wise. Select this option if the DST in your country starts and ends on a particular day of
the month. For example, if DST starts on the Second Sunday of March and ends on the First Sunday of
October.
OR
•
Date-Month Wise. Select this option if the DST in your country starts and ends on a particular date of
the month. For example, if DST starts on October 12 and ends on March 15.
Default: Day-Month Wise.
7. If you selected the Day-Month Wise option, configure the Start and End time for DST.
DST Start
•
•
•
•
Select the Ordinal day of the month when DST begins: 1st, 2nd, 3rd, 4th or 5th.
Select the Day of the month when DST begins: Sunday, Monday, Tuesday, Wednesday, Thursday,
Friday, Saturday.
Select the Month when DST begins: January to December.
Set the Time when you want DST to begin. The time mode is in 24 hours format.
Default: 1st Sunday March, Time 00 hours and 00 minutes.
DST End
• Select the Ordinal day of the month when DST ends: 1st, 2nd, 3rd, 4th or 5th.
• Select the Day of the month when DST ends: Sunday, Monday, Tuesday, Wednesday, Thursday,
Friday, Saturday.
• Select the Month when DST ends: January to December.
• Set the Time when you want DST to end. The time mode is in 24 hours format.
Default: 1st Sunday September, Time 00 hours and 00 minutes.
When the DST of a particular country starts or ends on the Last Sunday or any other day, e.g. the last
Tuesday, last Friday of the month, always set the Ordinal Number as '5th'.
8. If you select Date-Month Wise option, configure the following parameters:
DST Start
• Select the Month when DST begins: January to December.
• Select the Date on which DST begins: 1 to 31.
• Set the Time when DST begins. The time mode is in 24 hours format.
DST End
• Select the Month when DST ends: January to December.
• Select the Date on which DST ends: 1 to 31.
• Set the Time when DST ends. The time mode is in 24 hours format.
9. Click Submit to save your DST settings.
Example: If you are installing SETU ATA211 in a country in the European Union, as per the European Summer
Time, the DST would start on the Last Sunday in March and end on the Last Sunday in October each year. Clocks
Matrix SETU ATA211 System Manual
87
are advanced by one hour at 01:00 hours GMT at the start of DST and set back by one hour at 01:00 hours GMT
when DST ends.
1. Select the Daylight Saving Time Enable check box.
2. Set the Time Offset as 60 minutes.
3. Select the option Day-Month Wise as DST Type.
4. Configure the DST Start as follows:
•
•
•
•
Select 5th as the Ordinal.
Select Sunday as the Day.
Select March as the Month.
Set Time to 01 Hours and 00 Minutes.
5. Now, go to the option DST End, and configure as follows.
•
•
•
•
Select 5th as the Ordinal.
Select Sunday as the Day.
Select October as the Month.
Set Time to 01 Hours and 00 Minutes.
6. Click Submit to save DST settings.
88
Matrix SETU ATA211 System Manual
Static Routing Table
Static Routing Table is required when you have more than one router (Gateway) in your network and you want
SETU ATA211 to send packets to multiple routers/gateways for different types of calls.
To illustrate this with an example, two Local Area Networks, Network A and Network B, are connected through
Frame Relay/ MPLS network to give access to local resources and also to make Peer-to-Peer calls.
59.162.252.82
SIP Proxy
192.168.1.0/24
A
B
192.168.2.0/24
Public
IP
Frame Relay/MPLS
ATA211
ATA211
•
Both sites are also connected to public IP network:
• to give internet access to local hosts.
• to access the DID service provided by ITSPs to make PSTN/ GSM calls over the IP network.
•
SETU ATA211 is connected at both sites.
•
These sites are also connected to public IP network for the following reasons:
•
To give internet access to local hosts.
•
To access DID service provided by ITSPs to make PSTN/ GSM calls over IP network.
•
SETU ATA211 is connected at both sites, behind a router.
•
Network A and Network B are in different subnets.
•
You can configure only one default Gateway address in SETU ATA211 to send IP packets.
•
Now, as SETU ATA is connected behind two Routers, it will not be able to determine where to route the IP
packets.
•
So, either Peer-to-Peer calls or Proxy calls can be made at a time between Network A and Network B.
Matrix SETU ATA211 System Manual
89
The Static Routing Table in SETU ATA211 resolves this. The Static Routing Table defines the appropriate Gateway
Address (or Router’s LAN Address) where the IP packets are to be sent.
This Table makes it possible to route different types of outgoing calls (Peer to Peer or Proxy) made to different
subnets to the Gateway as per the called network.
In the Static Routing Table, you must configure:
• The address of the final Destination where the call is to be made.
• The Subnet Mask to be applied on the final destination address.
• The Gateway Address where the IP packets are to be sent.
When SETU ATA211 sends packets, if the final destination IP Address and SETU ATA211 are not in the same
Subnet, the system will check the Static Routing Table.
If a perfect match is found, SETU ATA211 will start sending the IP packets to the corresponding Gateway Address
configured in the table.
If no match is found, SETU ATA211 will send the IP Packets to the default Gateway Address you configured in the
“Network Parameters” page.
To take the above example further, if SETU ATA211 connected in Network A makes an outgoing call to
192.168.2.0/ 24, the call will be routed to Frame Relay/ MPLS link.
If the SETU ATA211 makes an outgoing call to the SIP proxy server 59.162.252.82, the call will be routed from
router which connects the system to public IP network.
Thus, on the basis of the destination address, SETU ATA211 will route the calls for the specified network to a
specific gateway.
Configuring Static Routing Table
The Static Routing Table must be configured at each location where SETU ATA211 is installed.
1. Login as Admin with your Password.
2. Click the link Advanced Settings to expand.
3. Click Static Routing.
The Static Routing Table opens.
90
Matrix SETU ATA211 System Manual
The Static Routing Table allows you to configure up to 5 entries. Each entry is stored against an Index
number.
For each entry, you must configure the following fields:
•
Destination Address: This is the address of the final destination where the call is to be made. This
can be a device IP Address or Network Address.
•
Subnet Mask: This is the mask to be applied on destination address.
•
Gateway Address: This is the IP address of the node where the IP packets are to be sent. Generally,
it is the IP address of the LAN interface of the Router (to which SETU ATA211 is connected).
The Gateway Address must be in the same subnet as SETU ATA211.
•
Click Submit to save your entries.
For example, the Static Routing Table of the SETU ATA211 at Location A, will be as shown below.
Index Destination Address Subnet Mask Gateway Address
1
192.168.2.0
255.255.255.0
192.168.1.1
:
5
Here, the Destination Address 192.168.2.0 specifies the network address of Location B.
The Subnet Mask is the mask to be applied on Destination address.
The Gateway Address 192.168.1.1 specifies the LAN address of the Router used to connect SETU
ATA211 at Location A with SETU ATA211 at Location B.
Now, the IP address of LAN interface of the Router which connects Location A to the Public Internet
should be configured as the ‘Default Gateway’ in the Network parameters.
With the Static Routing Table configured as shown above, packets sent by SETU ATA211 to
192.168.2.0/24 will be routed to the router which connects Location A to location B. Whereas, all
packets sent to an address other than 192.168.2.0/24 will be routed to the Default Gateway.
Matrix SETU ATA211 System Manual
91
Restart SETU ATA211
If you need to restart SETU ATA211, you may do it using Jeeves, instead of switching OFF and switching ON the
system again.
When you restart the system, all active calls will be disconnected and the ports in use will be released. The system
configuration however, will not be affected.
To restart the system using Jeeves,
1. Login as Admin with your Password.
2. Click the link Advanced Settings on the left pane to expand the links.
3. Click Restart.
4. An alert message will appear, "This will Restart System. Do you want to continue?”
5. Click OK button to restart the system.
92
Matrix SETU ATA1S System Manual
Reinstate Factory Defaults
SETU ATA211enables you to restore factory settings to all the programmable parameters using the option Factory
Defaults.
You can reinstate Factory Defaults by logging in as Admin or User. The factory set values will be assigned to all
parameters depending on the type of login, Admin or User.
When you log in as Admin to reinstate factory defaults, all parameters will be assigned default values except the
following:
• Time Parameters (see “Region”)
• Daylight Saving Time (DST) Parameters (see “Daylight Saving Time”).
• CPTG and Ring (see “Region”).
When you log in as User to reinstate factory defaults, default values will be assigned to the parameters listed
below:
• Supplementary Features
• Speed Dialing
• Network
• User Password
• Syslog
From the User Login, the Admin Password will be set to its default value, 1234, if you have enabled the option
'Default Admin password when ‘User’ defaults the ATA? in the System Parameters. See “Advanced Settings”.
Restoring Factory Defaults
Using Jeeves
To restore Factory Defaults from Admin mode,
1. Log in as Admin.
2. Click the Advanced Settings link on the left pane to expand.
3. Click Factory Defaults.
Matrix SETU ATA211 System Manual
93
An alert message will be displayed, "This option will assign default values to all the programmable
parameters and will Restart. Do you want to continue?"
4. Click OK.
The system will restart.
To restore Factory Defaults from User mode,
1. Log in as User.
2. Click Factory Defaults link under User Settings.
3. Click OK on the alert message: "This option will assign default values to all the programmable
parameters and will Restart. Do you want to continue?"
The system will restart.
Using Commands
1. Lift the handset of the phone.
2. To log in as Admin, dial the programming access code #19 followed by the Admin Password (default is
1234).
OR
3. To log in as User, dial the access code #18 followed by User Password (default is 1234).
4. You will get programming tone.
5. Dial 21-Reverse Admin/User Password-#*
For example: 21-4321-#* (the reverse of the default password 1234).
In case you have forgotten the password, set the User / Admin Password to default. See “Passwords” for
instructions.
94
Matrix SETU ATA211 System Manual
Software Upgrade
SETU ATA211 provides you the facility to upgrade the system software at the click of a button. SETU ATA211
supports an embedded FTP11 server which can be used for Uploading and Downloading System files,
configuration files, drivers etc.
To update configuration settings and firmware,
1. Login as Admin with your Password.
2. Click the link Advanced Settings on the left pane to expand.
3. Click System Upgrade. The following message box will be displayed.
4. In the Password field of the FTP login window, enter the Admin Password.
5. The following folders will be displayed:
•
•
•
config: contains the configuration files.
dhcp: contains files of DHCP configuration.
driver: contains the current driver files.
11. FTP or File Transfer Protocol is a standard Internet Protocol that is used to exchange files between computers on the IP network.
Matrix SETU ATA211 System Manual
95
•
•
•
ppp: contains files for PPPoE configuration.
system: contains the current firmware/software.
web: contains html files.
6. Click any of these folders to view the files that SETU ATA211 is currently using. You may either delete the
existing files or copy the existing files to another location (as backup).
7. Copy the new configuration files from their location and paste these new files in these folders.
Wait for the file transfer to complete.
8. Restart the system after uploading the files. The new configuration/driver/firmware will be applicable only
after the system restarts.
Before you upgrade software, you can save the existing application/configuration/driver/ web pages
folders and files as back-up for retrieval, later. For example: If you want to retain the existing Configuration
folder for future record, you can save the folder on your PC. When required, you can copy and paste the
same folder back on the FTP server of SETU ATA211.
96
Matrix SETU ATA211 System Manual
Syslog (Debug)
Debugs are logs of actions and events that take place on any computer system. These logs are useful for
troubleshooting and system security.
SETU ATA211 supports Syslog12 Client for debugging. Syslog Client enables the system to send debug messages
in syslog format to the remote 'Syslog Server' on IP network. You can view the system debug messages on the
remote server.
Each debug message includes the MAC Address of SETU ATA211 which is sending debug messages in 'syslog
server'.
SETU ATA211 supports following different Debug levels:
• APPL
• CONFIG
• SYS
• SIP
• CALL
• DSP
• REG
• STACK
• NAT
• AUTO CONFIG
• SNTP
• FXO
You can select any of these debug levels, and the Syslog Client will send only the debug messages for the selected
level to the remote server on the IP network. For example, if the debug log of Call is required, you can select this
option, and disable all others.
To be able to use this feature, you must enable 'Debug', configure the Remote Server Address and define the
Server Port on which Syslog will listen for debug messages.
Syslog uses the UDP as transport protocol and listens on the port 514 (the default listening port).
To debug the System from Admin mode,
1. Login as Admin with your Password.
2. Click the link Advanced Settings on the left pane to expand.
12. Syslog is one of the protocols used extensively for sending debug messages, and is defined in RFC 3164.
Matrix SETU ATA211 System Manual
97
3. Click Syslog.
4. Configure the following parameters:
•
Syslog: Select the check box to enable. Default: Disabled.
When the Debug flag is enabled, the system will send the debug messages to the Syslog Server IP
address. Debug report can be viewed on the Syslog Server or any other application which can capture
the Syslog messages/debug sent by the system.
•
Syslog Server Address: Port: Enter the IP Address of the Syslog Server.
Enter the address of the Listening Port of the Syslog Server from 1024-65535; 514. By default the
remote server port address is '514'.
•
Syslog Levels: By default, all debug levels are selected. Clear the check box to disable the debug
level you do not want. The system will send debug messages only for the level you have selected.
ATA supports following Syslog Levels:
• APPL
• CONFIG
• SYS
• SIP
• CALL
• DSP
• REG
• SNTP
• STACK
• NAT
• AUTO CONFIG
• FXO
5. Click Submit to save the settings.
98
Matrix SETU ATA211 System Manual
To debug the System from User mode,
1. Log in as User.
2. Click the Syslog link, under User Settings on the left pane.
3. To configure Syslog settings, refer the steps 4 and 5 described for the Admin mode.
Matrix SETU ATA211 System Manual
99
PCAP Trace
PCAP or packet capture consists of intercepting and logging the traffic passing over a digital network or a part of a
network. PCAP intercepts each packet in the data streams that flow across the network, and can decode and
analyze its contents.
PCAP can be used, among others, to monitor the network, analyze network problems, debug client/server
communications, debug network protocol implementations.
SETU ATA211 supports PCAP Trace, which you can use to detect and diagnose network related problems, for
example, when the SIP account is not getting registered, or any SIP related feature is not functioning.
Packets traveling over a network are captured and saved in the system. You can save these trace files (packets
captured by the system) on a PC and open these trace files using a graphical packet capture and protocol analysis
tool such as Wireshark or Ethereal.
A maximum of 1 MB of packets can be captured and stored in the system.
SETU ATA211 also supports Filters and Promiscuous mode for capturing packets, which you can use to specify the
types of data packets to be captured.
To use PCAP Trace from Admin mode,
1. Log in as Admin.
2. Click the Advanced Settings link on the left pane to expand.
3. Click PCAP.
4. Decide the type of packets to be captured and set the Filter accordingly. The Filter Settings parameter
should be maximum 60 characters in length. By default, this field is blank. So, all packets will be captured.
100
Matrix SETU ATA211 System Manual
Refer to the following examples to know how to set the Filters.
Examples of Filter settings:
• To capture packets of source port 5060, set the filter as src port 5060
•
To capture packets of destination port 80, set the filter as dst port 80
•
To capture packets transmitted from IP address 192.168.1.176, set the filter as src host 192.168.1.176
•
To capture packets received from IP address 192.168.1.176, set the filter as dst host 192.168.1.176
•
It is not mandatory to set Filters. When the Filter Settings field is left blank, the system will capture all
packets.
5. You may select the check box to enable Promiscuous Mode if you want. Default: Disabled.
When you enable Promiscuous Mode, the SETU ATA211 will capture all network traffic. However, this will
work only in a non-switched environment.
When Promiscuous Mode is disabled, the system will capture only traffic that is directly related to it. Only
traffic to, from or routed through the SETU ATA211 will be picked up by the PCAP Trace.
'Filter Settings' and 'Promiscuous Mode' (enabled) will not be cleared during power down.
6. Click the Start button to begin the capturing of the packets.
7. Click the Stop button to stop packet capture.
OR
Wait for the system to stop packet capturing. The system stops packet capturing once the maximum
allotted memory of 1 MB (RAM) is utilized.
Number of Packets and bytes captured as per the filter setting will be displayed as Packets Captured and
Total Bytes.
The Status field displays the current activity of packet capturing.
Capturing of packets will not stop if you open any other page of Jeeves. So, you may continue using
Jeeves for any other purpose while PCAP Trace is being used.
8. When the packet capturing is stopped (by you or the system), click the Save Trace File button to save the
files on your computer or on another computer.
A dialog box open. You can select the path for saving the trace file.
The current packets captured will not be deleted after you have saved the trace file. The current packets
will be deleted when you start the PCAP capture again.
9. You may log out of Jeeves.
Matrix SETU ATA211 System Manual
101
10. Now, you can open the trace files using Wireshark/Ethereal or any other similar software which supports
opening of trace files.
To use PCAP Trace from User mode,
1. Log in as User.
2. Click the PCAP link, under User Settings on the left pane.
3. To configure PCAP settings, refer the steps 4 to 10 described for the Admin mode.
102
Matrix SETU ATA211 System Manual
Auto Configuration
You can use Auto-Configuration to have the system automatically download the configuration files stored at a
central location: TFTP/HTTP/HTTPS Server.
This feature is useful for ITSPs and where multiple SETU ATA211 are connected. ITSPs can store the configuration
files of each SETU ATA211 that they provide to their customers on the Auto Configuration Server (ACS). The
configuration files of each ATA are to be stored in a folder named by its MAC Address.
When a customer connects to the ITSP network, the SETU ATA211 provided to the customer will automatically
download its configuration files stored in its MAC Address folder on the ACS. The customer can thus start using the
SETU ATA211 without the intervention or assistance of a technician, making it a 'plug-and-play' device.
To use this feature, end users must obtain from the ITSP or System Administrator the following information:
1. IP address of the Auto Configuration Server.
2. Path of the Folder (containing the configuration files) on the Auto Configuration Server.
3. The protocol to be used: TFTP, HTTP, HTTPS.
When your ACS uses HTTP, HTTPS protocol for Auto-Configuration, make sure:
•
•
•
The configuration files of each ATA are stored in a folder by its MAC Address.
Store the index.html or startup.html or any other default file name used by your server in the MAC Address
folder of each ATA.
This file should include the names of the configuration files of ATA in the same format as provided to you
on the CD-ROM supplied to you with your ATA. See the folder name Auto Configuration Sample Folder
on the CD.
When ATA sends GET request to perform Auto-Configuration, server should return index.html or
startup.html or other file, which includes the configuration file names to be supplied to ATA. Once ATA
receives the file (index.html or startup.html or other) with configuration file names, ATA will send separate
requests for each configuration file.
Using Auto Configuration:
1. Login as Admin with your Password.
2. Click the link Advanced Settings on the left pane to expand.
Matrix SETU ATA211 System Manual
103
3. Click Auto Configuration and configure the following parameter.
4. Auto Configuration: Select the desired method to be used to fetch configuration files. Default: Never.
•
Never: Select this option if you do not want Auto-Configuration process to be done during power ON.
•
At Each Power ON: Select this option if you want SETU ATA211 to perform Auto-Configuration at
each power ON.
•
At Next Power ON: Select this option if you want SETU ATA211 to perform Auto-Configuration only
during the next power ON. Once Auto-Configuration is done successfully, the option gets changed to
Never.
•
Resync Periodically: Select this option when SETU ATA211 does not need to auto configure during
power ON, but needs to resynchronize periodically with the ACS to check for updates in the
configuration. If you select this option, Auto-Configuration will be performed every time the Resync
Timer ends.
•
At Each Power ON & Resync Periodically: Select this option when SETU ATA211 needs to auto
configure during power ON and also to resynchronize periodically with the ACS to check for updates in
the configuration.
•
At Next Power ON & Resync Periodically: Select this option when SETU ATA211 needs to auto
configure only during the next power ON but resynchronize periodically with the ACS to check for
updates in the configuration. Once Auto-Configuration is done successfully at next power on, the option
gets changed to Resync Periodically option.
5. Protocol: Select the protocol used by the Auto-Configuration Server for file transfer. The system
generates file transfer request to the configuration server according to the protocol you selected. Default:
TFTP
104
•
TFTP: Select the radio button, if you want this protocol for the process of Auto-Configuration. TFTP is
preferred when Auto Configuration is to be done in Local Area Network (LAN).
•
HTTP: Select the radio button, if you want this protocol for the process of Auto-Configuration. HTTP is
preferred when Auto-Configuration is to be done in Wide Area Network (WAN).
Matrix SETU ATA211 System Manual
•
HTTPS: Select the radio button, if you want this protocol for the process of Auto-Configuration. HTTPS
is preferred when security is the concern during Auto-Configuration.
6. Server Address: Specify the Auto-Configuration Server Address. The Auto-Configuration Server Address
resembles the IP Address/Domain of ACS where all configuration files of SETU ATA211 are stored. The
server address can be configured using DHCP.
If the server address is to be configured manually, enter TFTP/HTTP/HTTPS server's IP address from
where ATA should download the configuration files. Default: Blank.
If you want the system to get the Server Address from the DHCP server, keep this field blank. Make sure
that you also set the 'Connection Type' on the Network page to 'DHCP'.
7. Config Folder Path: Specify the path of the folder (provided by your ITSP / System Administrator) on the
TFTP/HTTP/HTTPS server from where the configuration files are to be downloaded.
When SETU ATA211 gets auto configured, it will send the request for the configuration files to the selected
TFTP/HTTP/HTTPS server and restore the files from the folder as per this path.
Default: Blank.
8. Request Timeout: Request Timeout is used when SETU ATA211 tries to connect to the Auto-
Configuration Server for TCP/TLS binding. This timer specifies for how long SETU ATA211 should wait for
successful TCP/TLS binding.
Enter the required time in seconds. The range of Request Timeout is 01-99 seconds. Default: 60 seconds.
9. Retry Timer: This timer is used if the connection is not established with Auto-Configuration Server before
the expiry of the Request Timeout. Then, in such case, SETU ATA211 will try to reconnect automatically
after this time interval.
Enter the required time interval in seconds. The range of Retry Timer is 001-999 seconds. Default: 10
seconds.
10. Resync Timer: Resync Timer is the time after expiry of which SETU ATA211 will send the resync request
to check if there is any change in the configuration files. This timer is applicable only when Resync
Periodically or At Each Power ON & Resync Periodically or At Next Power ON & Resync
Periodically options of Auto-Configuration are selected.
Enter the required resync timer in hours. The range of Resync Timer is 001-999 hours. Default: 24 hours.
11. Click Submit to save.
Matrix SETU ATA211 System Manual
105
106
Matrix SETU ATA211 System Manual
CHAPTER 6
Features of SETU ATA211
Call Hold
Call Hold enables you to put an on-going conversation on hold, and call another person or receive a call from
another person. You can retrieve the call you put on hold, after the conversation with the other party has ended.
You can also retrieve the call you put on hold in the middle of the conversation with the other party.
Call Hold is also used in other features like Making Second Call, Call Waiting, Call Transfer- Blind, Call TransferAttended, Call Toggle and 3-Party Conference.
To use this feature, make sure that the Call Hold feature is enabled in the Class of Service of the FXS
port. See “FXS Port”.
Using Call Hold feature
•
•
•
•
•
You are in speech with party A.
To put your call with A on hold, dial Flash.
A is put on hold. You get feature tone for 7 seconds, followed by error tone.
To retrieve the call you put on hold, dial Flash again during feature tone OR during error tone.
You will in speech with A.
•
If you go On-hook during the feature tone, your call with party A will be disconnected.
•
If you go On-hook during error tone, you will get ring back. If you go Off-hook when your phone rings,
you will get connected with party A again.
Matrix SETU ATA211 System Manual
107
Making a Second Call
You can make a second call, by putting the current call on hold.
•
If the first call is a SIP call the second call can be a SIP or a PSTN call. But, if the first call is a PSTN
call the second call can only be a SIP call.
•
To use this feature, make sure that the Call Hold feature is enabled in the Class of Service of the FXS
port. See “FXS Port”.
Making a Second Call
•
•
•
•
•
You are in speech with party A.
Dial Flash to put party A on Hold.
You get feature tone.
Dial the number of the desired party B.
When party B answers the call, you are in speech with party B.
Making a second call feature can also be used with other features such as Call Transfer-Attended, Call
Toggle and 3-Party Conference.
108
Matrix SETU ATA211 System Manual
Call Transfer
Using Call Transfer you can connect the person you are in speech with, with another party.
SETU ATA211 offers two types of Call Transfer:
•
Call Transfer - Blind: You can transfer the call to the desired party, without informing the party of the
transfer.
•
Call Transfer - Attended: You can transfer the call to the desired party after consulting the party and or
obtaining their consent for transfer.
When you transfer a call, SETU A TA1S will wait for the notification from the destination number to which you have
transferred the call, for the duration of the 'Transfer Notification Timer'. This timer is set to 60 seconds by default. It
can be set to the desired value.
You will be notified about the success or failure of the transfer attempt during this Timer. You will get a confirmation
tone, when the call transfer is successful.
To use this feature, make sure that the Call Transfer feature is enabled in the Class of Service of the
FXS port. See “FXS Port”.
You may change the default value of the Transfer Notification Timer to the desired duration, if required,
from the “System Parameters” page under Advanced Settings.
Using Call Transfer
Call Transfer-Blind
•
•
•
•
•
•
•
•
You are in speech with party A.
Party A wishes to speak to party B.
Dial Flash-#6.
Party A is put on hold, and you will hear dial tone.
Dial the number of party B.
On successful transfer, you will get confirmation tone.
Party A will get connected with party B.
Replace the handset of your phone.
When you transfer a call, remain Off-hook, i.e. do not replace your handset, after dialing the transfer
destination’s number, until you know the result of the call transfer. One of the following results may occur:
• If the transfer is successful, you will get confirmation tone for 3 seconds, followed by error tone.
• If the transfer has failed, you will get error tone for 2 seconds and you will be connected to the
transferee (party A, in this case).
• If the transfer has timed out, i.e. the Notification Timer has expired and no notification has been
received from the transfer target (party B, in this case) you will get continuos error tone.
Call Transfer-Attended
•
•
•
•
•
You are in speech with party A.
Party A wishes to speak to party B.
Dial Flash.
Party A is put on hold, and you will hear dial tone.
Dial the number of party B.
Matrix SETU ATA211 System Manual
109
•
•
•
•
•
•
When party B answers the call, you will be in speech with party B.
You may now transfer the call if party B consents.
Dial Flash-#7 to transfer the call to party B.
On successful transfer, you will get confirmation tone.
Party A will get connected with party B.
Replace the handset of your phone.
To know the call transfer result, remain Off-hook after dialing the transfer target’s number (party B).
• If the transfer is successful, you will get a confirmation tone for 3 seconds followed by error tone.
• If the transfer has failed, you will get error tone for two seconds and will be connected to the transfer
target (party B), if available. If the transfer target has disconnected the call, you will be connected to the
transferee.
• If the transfer has timed out, you will get continuous error tone.
110
Matrix SETU ATA211 System Manual
Call Toggle
Call Toggle allows you to have two simultaneous telephone conversations, talking to two persons alternately.
You can toggle between: Two SIP calls, a SIP call and a PSTN call. The parties for Call Toggle can be:
• Two outgoing calls
• Two incoming calls
• One outgoing call and one incoming call
To use this feature, make sure that Call Toggle is enabled in the Class of Service of the FXS port. See
“FXS Port”.
Using Call Toggle
•
•
•
•
•
•
•
•
You are in speech with A and you want to talk to B.
Dial Flash, A is put on hold. You get feature tone.
Dial the number of B. When B answers the call, you are in speech with B.
To talk to A, dial Flash-#4.
You are in speech with A and B is put on hold.
To talk to B, dial Flash-#4 again.
You are in speech with B. A is put on hold.
This way, you can talk alternately to A and B, by dialing Flash-#4 again.
When toggling between calls, you can disconnect the call you are currently in speech with by going Onhook.
Matrix SETU ATA211 System Manual
111
Call Waiting
When your phone is busy, the Call Waiting feature notifies you about another incoming call in the form of beeps.
The Call Waiting feature of SETU ATA211 allows you to:
• reject/ignore the waiting call.
• hold the current call and attend to the waiting call.
• disconnect the current call and attend to the waiting call.
Configuring Call Waiting
To use this feature, make sure that the Call Waiting feature is enabled in the Class of Service of the FXS
port. See “FXS Port”.
Using Jeeves
To configure Call Waiting from the Admin mode:
1. Log in as Admin.
2. Click the Supplementary Services link on the left pane to expand.
3. Click Supplementary Features.
4. Keep the Call Waiting check box enabled.
5. Click Submit to save the settings.
6. You may log out.
To configure Call Waiting from the User mode:
1. Log in as User.
112
Matrix SETU ATA211 System Manual
2. Click the Supplementary Features link.
3. Keep the Call Waiting check box enabled.
4. Click Submit to save the settings.
5. You may log out.
Using Commands
•
•
•
•
•
•
Lift handset.
Dial #19-Admin Password (default: 1234).
OR
Dial #18-User Password (default: 1234).
Dial 72-1-#* to enable.
Dial 72-0-#* to disable.
Replace handset.
Using Call Waiting
When call waiting is enabled and you are busy on a call with party A,
•
You will hear beeps indicating another incoming call.
•
You may choose to do any of the following:
•
Reject the call, by dialing Flash-#3. The beeps will stop, you will remain in speech with party A.
Incoming call on the FXO port cannot be rejected. Hence, issuing this command will only stop playing
beeps and you will remain in speech with party A.
OR
•
put party A on hold, by dialing Flash-#4. The beeps will stop, you will be in speech with party B.
OR
Matrix SETU ATA211 System Manual
113
•
114
disconnect your call with party A, by dialing Flash-#5 and answer the waiting call. The beeps will stop,
you will be in speech with party B. Party A will be disconnected.
Matrix SETU ATA211 System Manual
Conference
Three-party Conference, also referred to as Three-Way Calling, is a telephone call, in which you can have two
other persons participate in the call.
You can initiate a conference by calling the first person, and then put the first person on hold to call the second
person. You can also include another person when you in the middle of speech with a person.
Conference can be made between PSTN and SIP calls or between two SIP calls. The parties to a conference can
be:
• Two outgoing calls
• Two incoming calls
• One outgoing call and one incoming call.
When you go On-hook during an active Conference, the Conference will be terminated and both the calls will be
disconnected.
While initiating the conference, the SETU ATA211 supports the Vocoder G.711 (Mu-law) only.
To use this feature, make sure that the Conference feature is enabled in the Class of Service of the FXS
port. See “FXS Port”.
Using Conference
•
•
•
•
•
•
•
•
•
Lift handset.
Dial the number of party A.
When A answers the call, dial Flash.
Party A is put on hold, and you will hear feature tone.
Now, dial the number of party B.
When B answers the call and you are in speech with B, dial Flash-#2.
Three-way speech will be established between you, party A and party B.
Replace the handset at the end of your conversation.
The conference will be terminated.
You can convert a 3-Party Conference to Call Toggle by dialing the Call Toggle access code Flash-#4.
You will be connected to one party and the other party will be put on hold.
Matrix SETU ATA211 System Manual
115
Do Not Disturb (DND)
If you do not want to receive any calls on your phone, you may set the Do-Not-Disturb feature on your phone. When
you set DND, all incoming calls on your phone will be rejected, but you can continue to make outgoing calls.
Configuring Do-Not-Disturb
To use this feature, make sure that Do-Not-Disturb feature is enabled in the Class of Service of the FXS
port. See “FXS Port”.
Using Jeeves
To set or cancel DND from Admin mode,
1. Log in as Admin.
2. Click the Supplementary Services link on the left pane to expand.
3. Click Supplementary Features link.
4. To set DND, select the Do-Not-Disturb check box. Default: disabled.
To cancel DND, clear the Do-Not-Disturb check box.
To set or cancel DND from User mode,
1. Log in as User.
116
Matrix SETU ATA211 System Manual
2. Click the Supplementary Features link, under User Settings on the left pane.
3. Select the Do-Not-Disturb check box to set DND. Default: Disabled.
To cancel, clear the check box.
Using Phone
•
•
•
Lift handset of your phone.
Dial #19-Admin Password (default: 1234).
OR
Dial #18-User Password (default: 234).
•
•
•
Dial 61-1-#* to set.
Dial 61-0-#* to cancel.
Replace handset.
Matrix SETU ATA211 System Manual
117
Call Forward
When you are away from your phone13, but would like to answer your calls, you can use the Call Forward feature to
have SETU ATA211 forward incoming calls to another number.
SETU ATA211 supports the following Call Forward options, which you can set on your phone:
•
Call Forward-Unconditional: All incoming calls received on the SIP Trunk are forwarded to the desired
destination number, automatically without waiting for a response from your phone.
•
Call Forward- Busy: All incoming calls received on the SIP Trunk are forwarded to the destination
number, when your phone is busy.
•
Call Forward- No Reply: All incoming calls received on the SIP Trunk are forwarded to the destination
number, when you do not answer your phone.
When you set Call Forward-No Reply, SETU ATA211 waits for the duration of the Call Forward-No Reply
Timer for the phone to answer. This timer is configurable, and is set to 45 seconds as default.
If the phone does not answer before the timer expires, SETU ATA211 considers it as No Reply and
forwards it to the desired destination number.
You can set a different destination number for each Call Forward option.
Configuring Call Forward
Call Forward feature is enabled in the Class of Service of the FXS port. See “FXS Port”.
Using Jeeves
To use Call Forward from Admin mode,
1. Log in as Admin.
2. Click the Supplementary Services link on the left pane to expand.
13. Connected to the FXS port of SETU ATA211.
118
Matrix SETU ATA211 System Manual
3. Click the Supplementary Features link.
4. Select the check box for the Call Forward option you want to set:
•
•
•
Call Forward-Unconditional
Call Forward-Busy
Call Forward-No Reply.
In the corresponding box enter the desired destination number (up to 40 characters) you want the calls to
be forwarded to.
5. If you selected Call Forward- No Reply, you may also change the duration of the no-reply Timer, if
required. The range of the Call Forward No-Reply Timer is 01 to 99 seconds. Default: 45 seconds.
6. Click Submit to save.
To use Call Forward from User mode,
1. Log in as User.
2. Click the Supplementary Features link under User Settings on the left pane.
3. Select the check box for the Call Forward option you want to set:
•
Call Forward-Unconditional
Matrix SETU ATA211 System Manual
119
•
•
Call Forward-Busy
Call Forward-No Reply.
In the corresponding box enter the desired destination number (up to 40 characters) you want the calls to
be forwarded to.
4. If you selected Call Forward- No Reply, you may also change the duration of the no-reply Timer, if
required. The range of the Call Forward No-Reply Timer is 01 to 99 seconds. Default: 45 seconds.
5. Click Submit to save.
Using Phone
Call Forward Un-conditional
To configure destination number for Call Forward-Unconditional:
•
•
•
•
•
Lift the handset of your phone.
Dial #19-Admin Password (default:1234)
OR
Dial #18-User Password (default:1234)
Dial 51-Destination Number-#*
Replace handset.
To set/cancel Call Forward-Unconditional:
•
•
•
•
•
•
Lift the handset of your phone.
Dial #19-Admin Password (default:1234)
OR
Dial #18-User Password (default:1234)
Dial 52-1-#* to set.
Dial 52-0-#* to cancel.
Replace handset.
Call Forward-Busy
To configure destination number for Call Forward-Busy:
•
•
•
•
•
Lift the handset of your phone.
Dial #19-Admin Password (default: 1234)
OR
Dial #18-User Password (default: 1234)
Dial 53-Destination Number-#*.
Replace handset.
To set/cancel Call Forward- Busy:
•
•
•
•
•
120
Lift the handset of your phone.
Dial #19-Admin Password (default:1234)
OR
Dial #18-User Password (default:1234)
Dial 54-1-#* to set.
Dial 54-0-#* to cancel.
Matrix SETU ATA211 System Manual
•
Replace handset.
Call Forward- No Reply
To configure destination number for Call Forward- No Reply:
•
•
•
•
•
Lift the handset of your phone.
Dial #19-Admin Password (default: 1234)
OR
Dial #18-User Password (default: 1234)
Dial 55-Destination Number-#*.
Replace handset.
To set the Timer for Call Forward-No Reply:
•
•
•
•
•
Lift handset of your phone.
Dial #19-Admin Password (default: 1234)
OR
Dial #18-User Password (default: 1234)
Dial 57-Time-#*. Valid range of the Timer is 01-99 seconds.
Replace handset.
To set/cancel Call Forward-No Reply:
•
•
•
•
•
•
Lift the handset of your phone.
Dial #19-Admin Password (default:1234)
OR
Dial #18-User Password (default:1234)
Dial 56-1-#* to set.
Dial 56-1-#* to cancel.
Replace handset.
Matrix SETU ATA211 System Manual
121
Caller ID Restriction
If you do not want your caller ID to be displayed to the called party, you can do so using this feature.
Configuring Caller ID Restriction
Using Jeeves
1. Log in as Admin with your Password.
2. Click the Basic Settings link on the left pane to expand.
3. Click SIP to open the SIP trunk parameters page.
4. Select the desired SIP Trunk by clicking the SIP trunk number tab.
5. Click More button to view all parameters on the page.
6. Scroll to Advanced.
7. Enable CLIR to hide your Caller ID. Default: Disabled.
:
Using Commands
•
•
•
•
122
Lift handset.
Dial #19-Admin Password (default: 1234).
Dial 66-SIP Trunk Number -Code-#*
Where,
SIP Trunk Number is
1 for SIP Trunk 1
2 for SIP Trunk 2
3 for SIP Trunk 3
Code is
1 to Enable CLIR
0 to Disable CLIR
Replace handset.
Matrix SETU ATA211 System Manual
Selective Trunk Access
Regardless of the trunk selected for ‘Outgoing Call Routing’, you can make outgoing calls from any trunk by dialing
the Access Code for that trunk.
1. To dial a number from FXO,
•
•
•
•
Lift the handset of your phone.
Dial #83.
Dial the desired number.
Talk, when the remote party answers the call.
2. To dial a number from SIP1:
•
•
•
•
Lift the handset of your phone.
Dial #84.
Dial the desired number.
Talk, when the remote party answers the call.
3. To dial a number from SIP2:
•
•
•
•
Lift the handset of your phone.
Dial #85.
Dial the desired number.
Talk, when the remote party answers the call.
4. To dial a number from SIP3:
•
•
•
•
Lift the handset of your phone.
Dial #86.
Dial the desired number.
Talk, when the remote party answers the call.
Matrix SETU ATA211 System Manual
123
Speed Dialing
As the name itself suggests, this feature offers you a quick way to dial a number. Using this feature, you can make
an outgoing call to a particular number by dialing a short code instead of dialing the entire number string.
Speed Dialing feature works on the basis of the Speed Dialing Table, which you must configure separately for each
port.
The Speed Dialing Table consists of Index Numbers that serve as short codes. You must store contact numbers
(along with their names) that you want to speed dial against the Index numbers in the table and select the
Destination Route through which the number should be dialed out.
Using Speed Dialing from the FXO port,
• Dial the FXO port number of ATA211.
• ATA will answer the call and then you can dial the feature access code for Speed Dial (#9) followed by the
Index Number.
• SETU ATA211 will check the FXO Speed Dialing Table to fetch the number configured for the Index
number and the corresponding Destination trunk (SIP1 / SIP2 / SIP3) to dial out the number.
This feature will work on the FXO port, only if Incoming Call Routing option is selected as:
• Answer the call, collect number & route as per incoming call route selection.
• Route to FXS. If not answered within ring timer, answer the call, collect number & route as per incoming
call route selection
Using Speed Dialing from the SIP Trunk,
• If you dial the SIP Trunk number of ATA211.
• ATA will answer the call and then you can dial the feature access code for Speed Dial (#9) followed by the
Index Number.
• SETU ATA211 will check the SIP Speed Dialing Table to fetch the number configured for the Index
number
• This number will be out dialled from the FXO port.
This feature will work on the SIP Trunk, only if Incoming Call Routing option is selected as Answer the call,
Collect number and route to FXO. See “SIP Trunks” topic.
In the Number field, if you enter:
• SIP ID, the Destination trunk configured can be a peer-to-peer or proxy SIP trunk.
• IP Address / SIP URI, the Destination trunk must be can a peer-to-peer SIP trunk only.
Using Speed Dialing from the FXS port,
• Lift the handset
• Dial the feature access code for Speed Dial (#9) followed by the Index Number.
• SETU ATA211 will check the FXS Speed Dialing Table to fetch the number configured for the Index
number and the corresponding destination Destination trunk (SIP1 / SIP2 / SIP3 / FXO) to dial out the
number.
124
Matrix SETU ATA211 System Manual
Configuring Speed Dialing
To use Speed Dialing you must configure the Speed Dialing Table separately for each port.
To configure Speed Dialing for the FXS port from the Admin mode:
1. Log in as Admin.
2. Click the Supplementary Services link on the left pane to expand the links.
3. Click Speed Dialing.
The Speed Dialing Table page opens. You can configure upto 20 entries in this table.
Against each index number:
•
•
•
•
Enter the Name (Max 24 characters) of the contact you wish to speed dial.
Enter the Number (Max. 40 characters) against each name.
Select the appropriate Destination Route, through which you want the system to dial out the number.
If you have finished entering, click Submit.
4. Similarly, to configure Speed Dialing Tables for the FXO port and the SIP trunk, click the FXO and SIP tabs
respectively.
To configure Speed Dialing for the FXS port from the User mode:
1. Log in as User.
Matrix SETU ATA211 System Manual
125
2. Click the Speed Dialing link. The Speed Dialing Table opens.
3. To configure the Speed Dialing Table, follow the same instructions as provided for configuring the table
from the Admin mode.
126
Matrix SETU ATA211 System Manual
Supplementary Services of Service Provider
When SETU ATA211 interfaced with a service provider server—ITSP, the Matrix ETERNITY IP-PBX, or any other
PBX—that supports supplementary services that require dialing of Flash14, like Call Hold, Call Transfer, Call
Waiting, you may choose to access the features of the service provider, or to access primarily, the features of
SETU ATA211.
If you want to use the features of the service provider, you must select Network as the Subscriber Type for the FXS
port of SETU ATA211.
If you want to use the features of SETU ATA211, you must select Gateway as the Subscriber Type for the FXS port
of SETU ATA211. However, you will be able to access the features of the service provider or network, also in the
Gateway mode, by dialing Flash, followed by #0, the Access Code for Using Supplementary Services of Service
Provider.
When the SETU ATA211 is set in the Gateway mode, when you dial flash and the access code #0 to access the
supplementary services of the service provider, the active call will be put on hold and you will get a feature tone.
SETU ATA211 will start the an internal timer, called the Service Provider Access Code Wait Timer. This timer
has a duration of 10 seconds. Any activity performed on the FXS port within this timer will be sent to the service
providers server. Any activity performed on the FXS port after the expiry of this timer, will be processed by SETU
ATA211.
To use Supplementary Services of Service Provider, configure the parameter Subscriber Type on the
FXS port as Network or as Gateway. See the topic “FXS Port” under Basic Settings.
Using Supplementary Services of Service Provider
If you have set SETU ATA211 in the Network Mode,
•
•
Dial Flash during speech.
You will get feature tone played by your service provider.
Dial feature access code provided by the service providers server.
If you have set SETU ATA211 in the Gateway Mode,
•
•
•
14.
Dial Flash during speech. This will place the active call on hold and you will get a feature tone.
Dial #0.
You will be in Network mode for 10 seconds.
Dial the feature access code provided by the service providers server within 10 seconds.
To be able to use features of the service provider SETU ATA211 supports dialing of Flash during speech on SIP.
Matrix SETU ATA211 System Manual
127
Multi Stage Dialing
Multi-stage Dialing is useful when SETU ATA211 connected to a SIP Server being used for networking the PBXs of
multiple sites. The extension users of the networked PBXs can dial the entire number string, both the destination
number and the extension number of the destination PBX together. The SETU ATA211 will split the string into two
stages. It will dial out the destination number first, and on receiving the answering signal from the PBX, it will dial
the extension number. Thus, extension users of all the networked PBXs can call each other, without hassle.
Let us understand this with the help of an example.
•
An organization has multiple offices across the globe: Canada, Australia, India and China. They require
voice over IP network connectivity for inter-branch calling.
•
At each office site, the existing voice infrastructure includes a PCM/ TDM PBX that does not support VoIP
connectivity.
•
So, to network the PBXs of the branch offices,
•
SETU ATA211 is interfaced with the existing PCM/ TDM PBX at each country office for VoIP
connectivity.
•
At the Head Office, an IP PBX is installed, connected to the public IP network.
•
The SETU ATA211 installed at the branch offices are registered with the IP PBX at the head office..
101
102
103
104
PBX1
FXS1
PBX2
FXO1
FXS2
FXO1
FXS1
FXO2
FXS2
PSTN
PSTN
FXO2
FXS3
FXS3
ATA1
FXS4
FXOn
FXS
ATA2
22
21
IP
FXS4
FXS
101
102
103
104
FXOn
IP
IP PBX
ATA1 - 21
ATA2 - 22
ATA3 - 23
ATA4 - 24
IP
101
102
103
104
PBX3
FXS1
PBX4
FXO1
FXS
23
FXS2
ATA3
FXS3
FXS4
FXOn-1
PSTN
FXOn
128
IP
FXS
24
FXO1
FXS1
FXS2
ATA4
PSTN
FXS3
FXOn-1
FXS4
101
102
103
104
FXOn
•
At the Canada office, PBX1 is interfaced with SETU ATA211, which is assigned the SIP ID 21.
•
At the Australia office, PBX2 is interfaced with SETU ATA211, which is assigned SIP ID 22.
Matrix SETU ATA211 System Manual
•
•
At the India office, PBX3 is interfaced with SETU ATA211, which is assigned SIP ID 23.
•
At the China office, PBX4 is interfaced with SETU ATA211, which is assigned a SIP ID 24.
Now, from the office in Canada, where PBX1 is installed, the extension user 101 of PBX1 wants to call
extension 102 of PBX2 in Australia. This is how it would work in absence of Multi-stage Dialing:
•
Extension user 101 of PBX1 dials the access code for a trunk line, followed by the number 22, which is
the SIP ID assigned to SETU ATA211 installed in Australia, and then the extension number 102. The
PBX1 routes this call to its FXO port which is connected to the FXS port of SETU ATA - 21.
•
SETU ATA - 21, then routes this call to IP-PBX, which is further routed by the IP-PBX to SETU ATA 22.
•
SETU ATA - 22 places the incoming call on its FXS port as per incoming call logic. PBX2 is connected
to the FXS port of SETU ATA -22.
•
PBX2 receives the incoming call. PBX2 has Auto-Attendant or Direct Inward Dialing enabled on the
landing trunk to answer the call on its FXO port.
•
Answer Signal is detected by SETU ATA -21.
•
PBX2 plays dial message/dial tone.
•
The caller (Extension 101 of PBX1) then dials 102, the desired called party number. PBX2 places the
call to its extension,102.
Thus, to make a call to an extension of another office, extension users need to dial the number in two stages, each
time, to reach the extension of the other office. In the first stage, the calling extension user dials the SIP ID of SETU
ATA. In the second stage, the calling extension user dials the desired extension number.
When Multi-Stage Dialing is used, extension users need to dial only the complete number string in one stage,
and SETU ATA211 converts the dialing method automatically into two stages.
To take the above example further, when Multi-Stage Dialing is used this is how it would work,
•
SETU ATA -21 (at calling end) accepts the complete number—trunk access code + SIP ID of ATA in
Australia + extention number 102—dialed by the extension user.
•
It dials only the number of the remote SIP device, which is SETU ATA - 22 (at called side).
•
When the call matures, SETU ATA - 21 (at calling end) then sends the remaining numbers - 102 - in DTMF
to the called device, SETU ATA -22.
•
While SETU ATA - 21 is sending the DTMF (102, the actual destination number which is the extension of
called PBX 2), the caller (extension 101 of PBX1) will hear the routing tone, if the Play Routing Tone flag
is enabled in the System Parameters of ATA - 21.
Matrix SETU ATA211 System Manual
129
Configuring Multi-Stage Dialing
For this feature to work, at each site where the SETU ATA211 is installed, do the following:
• Make sure that Auto Attendant or Direct Inward Dialing is enabled on the FXO port of the PBX on which
SETU ATA211 is interfaced.
• Enable Automatic Number Translation on the desired SIP Trunk of SETU ATA211.
• Configure the Automatic Number Translation Table.
• Set the DTMF ON Time, DTMF OFF Time.
• Enable ‘Play Routing Tone’ in the System Parameters, if required.
• Set the Pause Timer to the desired value.
To configure Multistage Dialing at each site where the SETU ATA211 is connected,
130
•
Open Jeeves.
•
Log in as Admin with your password.
•
Click the Basic Settings link.
•
Under Basic Settings, click SIP.
•
Now, click the SIP Trunk number tab (SIP Trunk 1, 2, or 3) on which you want to apply Multi-stage Dialing.
•
Click the More button to view all parameters on this page.
•
Scroll to Advanced.
•
Enable Automatic Number Translation on this SIP Trunk.
•
To configure the Automatic Number Translation Table, click the arrow icon.
Matrix SETU ATA211 System Manual
The Automatic Number Translation Table opens in a new window.
The Automatic Number Translation Table can accommodate upto 24 Dialed Numbers and their
corresponding Substitute Numbers, which are stored against Index numbers 01 to 24.
In the Dialed Number column, enter the numbers that users will dial out using the SIP trunk.
In the Substitute Number column, enter the number which the system should dial out in place of the
number dialed by the users.
The SETU ATA211 considers the character '~' as Wait for Answer and it considers the character '^' as
Pause.
You may use these characters in the Substitute Numbers, if you want SETU ATA211 to provide suitable
delay.
Make sure you enter a Dialed Number and its corresponding Substitute Number at the same Index. For
example, if you enter 22 as Dialed Number at Index 01, enter the Substitute Number 22~ also at Index 01.
To take the above example further, if extensions of PBX1 want to reach the extensions of PBX2 by dialing
22 + Extension Number (of PBX2), you must configure the Dialed Number and Substitute Number at
calling side, i.e. SETU ATA - 21, as follows:
Index Dialed Number Substitute Number
01
22
22~
02
03
::
24
Matrix SETU ATA211 System Manual
131
When any extension user of PBX1 dials '22 + Extension Number (of PBX2)', for example, 22101 (to reach
the extension 101 of PBX2),
•
SETU ATA -21 will first dial out ‘22’, which is the SIP ID of the called ATA and wait for answer' (22~).
The caller will only hear routing tone.
•
PBX2 on the called side answers the call (DID/Auto-Attendant must be enabled on the FXO port).
•
When the call matures, SETU ATA - 21 will send the remaining numbers, 101 in the RFC 2833
(Outband) to the called device, SETU ATA - 22.
•
These DTMF digits are then detected by PBX2 on its FXO port. The PBX places the call to extension
101.
•
In the above scenario, if you want some delay after the call matures and before SETU ATA -21 sends
the remaining DTMF digits, program '22~^' as Substitute Number instead of '22~'.
Index Dialed Number Substitute Number
01
22
22~^
02
03
::
24
•
Click Submit to save your entries.
•
Close the window.
•
Keep the DTMF ON and DTMF OFF Time to default values, if you don't have any specific requirement.
•
Change the Pause Timer to the desired value, if required. Default: 2 seconds.
•
Click Submit to save your SIP Trunk settings.
•
If you want Routing Tone to be played to the calling extension user, keep the Play Routing Tone flag
enabled in the “System Parameters” page.
•
You may log out of Jeeves or continue, as required.
The above example and configuration instructions are for Multi-stage Dialing on SIP trunks only. You may
also configure Multi-stage Dialing on the FXO port, if required.
132
Matrix SETU ATA211 System Manual
Disconnect the Call
You can disconnect a call by using an access code (default: #82). When the call disconnect access code is dialed,
the system will release the port engaged in the call.
Using Disconnect the Call
•
•
•
•
A is in speech with B
A dials #82 (access code for Disconnect the Call).
The current call is released.
A gets error tone.
You can disconnect calls using access codes on the FXO and FXS port only.
Matrix SETU ATA211 System Manual
133
Making New Call
Making New Call feature enables you to make a new call in the middle of an active call, by dialing an access code.
ATA will release the current call and you will get the dial tone, enabling you to dial digits for making the new call.
Using Making a New Call
1. A is in speech with B.
2. A dials #81 (access code for Making New Call).
3. The current call is released, A gets dial tone.
4. A can dial C’s number.
5. A is in speech with C.
•
•
•
•
•
134
You can use access code for Making New Call on the FXO and FXS port.
This feature call be used only by the caller.
If you have a call on hold, you will not be able to use Making New Call feature for the second call.
Making New Call will not be applicable when you are in a conference.
To use this feature make sure that the Incoming call routing option selected on the FXO port is:
• Answer the call, collect number & route as per incoming call route selection
• Route to FXS. If not answered within ring timer, answer the call, collect number & route as per
incoming call route selection
Matrix SETU ATA211 System Manual
PIN Authentication
SETU ATA211 supports PIN Authentication for outgoing calls from the FXS port and for incoming calls on the FXO
port and SIP trunks.
You may use PIN Authentication on the FXO port / the SIP trunks / FXS port to restrict access to SETU ATA211 to
specific callers.
The PIN Authentication feature works on the basis of the PIN Authentication Table, which you must configure.
When you enable PIN Authentication on the FXO port or the SIP trunk, for each incoming call,
•
•
•
•
•
ATA211 will answer the call and play Prompt tone to the caller.
the caller must dial the PIN.
ATA211 matches the PIN dialed by the caller with the PIN Authentication Table.
If a match is found the caller is authenticated and the caller can dial the number.
If no match is found ATA211 will play error tone, followed by Prompt tone. The caller is allowed two more
attempts to dial the PIN. If PIN Authentication fails again ATA will disconnect the call.
This feature will work on the FXO port, only if Incoming Call Routing option is selected as:
• Answer the call, collect number & route as per incoming call route selection.
OR
• Route to FXS. If the call is not answered within ring timer, answer the call, collect number & route as
per incoming call route selection.
This feature will work on the SIP trunk, only if Incoming Call Routing option is selected as:
• Answer the call, collect number and route to FXS.
OR
• Answer the call, collect number and route to FXO.
When you enable PIN Authentication on the FXS port, for each number dialed:
• ATA211 plays Prompt tone to the user.
• the user must dial the PIN.
• ATA211 matches the PIN dialed by the user with the PIN Authentication Table.
• If a match is found the user is authenticated and user can dial the number.
• If no match is found ATA211will play error tone followed by Prompt tone. The user is allowed two more
attempts to dial the PIN. If PIN Authentication fails thrice ATA will not allow the user to dial any number.
Configuring PIN Authentication
To use this feature, make sure you have enabled PIN Authentication on the desired port type: FXS, FXO, SIP.
• On the FXO port, enable the Authenticate Incoming Calls check box. See “FXO Port”
• On the SIP trunk, enable the Authenticate Incoming Calls check box. See “SIP Trunks”
• On the FXS port, enable the Authenticate Outgoing Call check box. See “FXS Port”
Now configure the PIN Authentication Table.
1. Log in as Admin.
2. Click the Advanced Settings link on the left pane to expand the links.
Matrix SETU ATA211 System Manual
135
3. Click PIN Authentication.
The PIN Authentication Table page opens. You can configure upto 100 entries in this table. This Table is
common for all port types.
•
Enter the PIN to be authenticated against each Index in the Table.
The PIN can have a maximum of 4 digits. The characters allowed are: 0 to 9,*, #
•
136
If you have finished entering the PIN Numbers, click Submit to save your entries.
Matrix SETU ATA211 System Manual
CHAPTER 6
System Status
You may view the status of the System, the Network ports (LAN and WAN), SIP Trunks and Auto Configuration
from Jeeves.
You can also check the status of certain parameters, like the Registration status of SIP Trunks, IP Address and
Subnet Mask of the LAN and WAN port, on the display of the Phone connected to FXS port by dialing the relevant
“System Commands”.
Viewing System Status from Jeeves
To view System Status on Jeeves from Admin Mode,
•
Log in as Admin.
•
Click the Status link to open the page.
To view System Status on Jeeves from User Mode,
Matrix SETU ATA211 System Manual
137
•
Log in as User.
•
Click Status link to open the page.
SIP
•
138
The following parameters will be displayed for SIP trunks 1, 2 and 3.
Matrix SETU ATA211 System Manual
•
Status: In this field, different status messages may be displayed, each of which are described briefly in the
table below.
Status
Description
Disable
Shows that SIP Trunk is disabled.
Registering
Shows that SIP Trunk is enabled and is waiting for response from the SIP
server.
Active
Shows that SIP Trunk is registered with the SIP server.
Failed
Shows that some error has occurred in the SIP Trunk and no calls can be
made using it (applicable only in case of Proxy Account).
•
Registration Time: The SIP Trunk is registered with the Registrar Server for a particular time period, after
which it has to be re-registered. The registrar server indicates the time remaining for re-registration of the
SIP Trunk. The same time is displayed in this field.
•
Registration Retry Count: This field displays the total number of register messages which have been
sent to the registrar server for registering SIP Trunk.
•
Reg. Last Failed Reason: This field displays the reason for failure of SIP Trunk registration with the
registrar server. The different reasons for registration failure that may appear in this field are:
Reason for Failure
Description
Message send fail
This reason is displayed when registration request sent to registrar
server fails.
Failed to create Register client
This reason is displayed when SIP stack has memory constraint/
resource limitation/ the number of SIP clients to register is greater
than the number programmed in the stack.
Failed to detach register client
This reason is displayed when SIP stack has memory constraint/
resource limitation/ the number of SIP clients to register is greater
than the number programmed in the stack.
Failed to send request
This reason is displayed when DNS server is not programmed.
Local Failure
This reason is displayed when DNS query fails.
Response time-out
This reason is displayed on the expiry of the General Request Timer.
Error Response- 4xx to 6xx
This is error response code.
No contact header in 2xx
This reason is displayed when no contact address is received in 2xx
response from the SIP server.
Authentication Failed
This reason is displayed when the SIP server does not authenticate
SETU ATA.
STUN address is not programmed
This reason is displayed when STUN is enabled but address is not
configured.
STUN query fail
This reason is displayed when a query to the STUN server fails.
Outbound address is not
programmed
This reason is displayed when Outbound is enabled but Outbound
address is not configured.
Router's IP address is not
programmed
This reason is displayed when Router's IP Address is to be used in
signaling but the address is not programmed.
Matrix SETU ATA211 System Manual
139
Network
LAN
•
IP Address: This field displays the current IP Address of the LAN port.
•
Subnet Mask: This field displays the current Subnet Mask Address of the LAN port.
•
MAC Address: This field displays the MAC Address of the LAN port.
WAN
140
•
•
Routing Mode: This field displays the Routing Mode selected, that is NAT or Bridge.
IP Address: This field displays the current IP Address of the WAN port.
•
Subnet Mask: This field displays the current Subnet Mask Address of the WAN port.
•
Gateway Address: This field displays Gateway Address assigned to the WAN Port of SETU ATA211. This
field displays the IP Address of the LAN port of the Router.
•
Primary DNS Address: This field displays the Primary DNS address of SETU ATA211.
•
Secondary DNS Address: This field displays the Primary DNS address of SETU ATA211.
•
DNS Domain Name: This field displays the DNS Domain Name of SETU ATA211.
•
MAC Address: This field displays MAC Address of the WAN Port of SETU ATA211.
Matrix SETU ATA211 System Manual
•
NAT Type: This field displays the NAT Type, if STUN is enabled in SETU ATA211. Commonly used NAT
types are:
• Unknown
• Open
• Conenat
• Restrictednat
• Portrestrictednat
• Symmetricnat
• Symmetricfirewall
• Blocked
•
IP Address fetched using STUN: This field displays the IP address fetched using STUN, if STUN server
address is configured.
•
SIP Port fetched using STUN: This field displays the SIP port fetched using STUN if STUN server
address is configured.
System
Date &Time
•
Current Date: The Current Date is displayed in this field.
•
Current Time: Current Time is displayed in this field.
.
Matrix SETU ATA211 System Manual
141
Firmware
•
Version-Revision: Current Software Version-Revision of SETU ATA211 is displayed here.
•
Kernel Date: The Date of current Kernel of the system is displayed here.
.
Auto Configuration
•
Status: This field displays the type of Auto Configuration option selected.
•
Next Resync: This field displays when the system will resync next for Auto Configuration.
•
Last Resync: This field displays the time when the system last resynchronized with the Auto Configuration
server.
•
You may log out of Jeeves.
Viewing System Status on Phone
To view System Status on the phone’s display from Admin Mode,
•
Lift the receiver of the phone.
•
Dial #19.
•
Dial the Admin Password (default: 1234).
To view System Status on phone’s display from User Mode,
•
Lift the receiver of the phone.
•
Dial #18.
•
Dial the User Password (default: 1234).
You will get programming tone.
On entering Admin/User Mode,
•
Dial the System Command for the status you want to view.
•
You get confirmation tone.
•
Go On-Hook (replace the receiver of the phone) on confirmation tone.
•
Your phone will ring.
•
The status for the port or trunk for you dialed the command will be displayed on your phone.
For example:
To view the IP address of the WAN port,
Dial 31-#*
142
Matrix SETU ATA211 System Manual
Go On-hook at the confirmation tone.
Your phone rings, and the IP Address will be displayed on your phone as: 192168001001
To view the WAN Subnet Mask,
Dial 33-#* and go On-hook at the confirmation tone.
Your phone rings and WAN Subnet Mask is displayed as: 255255255000
To view the IP address of LAN port,
Dial 32-#*
Go On-hook at the confirmation tone.
Your phone rings, and the IP Address of the LAN port is displayed as: 192168050001
To view the LAN Subnet Mask,
Dial 34-#* and go On-hook at the confirmation tone.
Your phone rings and the LAN Subnet mask is displayed as: 255255255000
To view the Gateway Address,
Dial 35-#* and go On-hook at the confirmation tone.
Your phone rings and the Gateway Address is displayed as: 192168001254
To view Primary DNS Address,
Dial 36-#* and go On-hook at the confirmation tone.
Your phone rings and the DNS Address is displayed as: 202100098054
To view Secondary DNS Address,
Dial 39-#* and go On-hook at the confirmation tone.
Your phone rings and the Secondary DNS Address is displayed as: 202100098053
To view the Connection Type,
Dial 37-#* and go On-hook at the confirmation tone.
If your connection type is DHCP, the phone will display 001
If your connection type is PPPoE, the phone will display 002
If your connection type is Static, the phone will display 003
To view the registration status of SIP Trunk,
Dial 38-SIP Trunk Number-#* and go On-hook at confirmation tone.
SIP Trunk Number is 1 for SIP Trunk1, 2 for SIP Trunk2 and 3 for SIP Trunk3
Your phone will ring and display one of the following:
001 for Disabled
002 for Registered
003 for Registering, when registration request is sent and the system is waiting for response
004 if the SIP trunk is configured as Peer-to-Peer Trunk.
005 if the registration request has failed, cannot be sent to the server.
Each time you go On-hook to view status of a port or trunk, you must enter the configuration mode again to
view the status of another ports or trunks.
Matrix SETU ATA211 System Manual
143
144
Matrix SETU ATA211 System Manual
Appendix
Call Progress Tone Generation
Dial Tone
Code Country
Ring Back Tone
Busy Tone
Error Tone1
Error Tone2
Freq.
Cadence
Freq.
Cadence
Freq.
Cadence
Freq.
Cadence
Freq.
Hz
second
Hz
second
Hz
second
Hz
second
Hz
second
Australia
425*25
cont.
400*25
0.4on 0.2off
0.4on 2.0off
425
0.375on
0.375off
425
0.375on 0.375off
425
1on 1off
02
Argentina
425
cont.
425
1.0on 4.0 off
425
0.3on 0.2off
425
0.3on 0.4off
425
1on 1off
03
Belgium
425
cont.
425
1.0on 3.0off
425
0.5on 0.5off
425
0.167on 0.167off
425
1on 1off
04
Brazil
425
cont.
425
1.0on 4.0 off
425
0.25on 0.25off
425
0.25on 0.25 off
425
1on 1off
05
China
450
cont.
450
1.0on 4.0off
450
0.35 on
0.36off
450
0.7on 0.7off
450
1on 1off
06
Egypt
425*50
cont.
425*50
2.0on 1.0off
425*50
1.0on 4.0off
450
0.5on 0.5off
450
1on 1off
07
France
440
cont.
440
1.5on 3.5off
440
0.5on 0.5off
440
0.25on 0.25off
440
1on 1off
08
Germany
425
cont.
425
1.0on 4.0off
425
0.48on 0.48off
425
0.24on 0.24off
425
1on 1off
09
Greece
425
0.2on 0.3off
0.7on 0.8off
425
1.0on 4.0off
425
0.3on 0.3off
425
0.15on 0.15off
425
1on 1off
10
India
400*25
cont.
400*25
0.4on 0.2off
0.4on 2.0off
400
0.75on 0.75off
400
0.25on 0.25off
400
1on 1off
11
Indonesia
425
cont.
425
1.0on 4.0off
425
0.5on 0.5off
425
0.25on 0.25off
425
1on 1off
12
Iran
425
cont.
425
1.0on 4.0off
425
0.5on 0.5off
425
0.25on 0.25off
425
1on 1off
01
Cadence
13
Israel
400
cont.
400
1.0on 3.0off
400
0.5on 0.5off
400
0.25on 0.25off
400
1on 1off
14
Italy
425
cont.
425
1.0on 4.0off
425
0.5on 0.5off
425
0.2on 0.2off
425
1on 1off
15
Japan
400
cont.
400*20
1.0on 2.0off
400
0.5on 0.5off
400
0.25on 0.25off
400
1on 1off
16
Kenya
425
cont.
425
0.67on 3.0off
1.5on 5.0off
425
0.2on 0.6off
0.2on 0.6off
425
0.2on 0.6off
425
1on 1off
17
Korea
350+440
cont.
440+480
1.0on 2.0off
480+620
0.5on 0.5off
480+620
0.3on 0.2off
480+620
1on 1off
18
Malaysia
425
cont.
425
0.4on 0.2off
0.4on 2.0off
425
0.5on 0.5off
425
0.5on 0.25off
425
1on 1off
19
Mexico
425
cont.
425
1.0on 4.0off
425
0.25on 0.25off
425
0.25on 0.25off
425
1on 1off
20
New Zealand
400
cont.
400+450
0.4on 0.2off
0.4on 2.0off
400
0.5on 0.5off
400
0.25on 0.25off
400
1on 1off
21
Philippines
425
cont.
425+480
1.0on 4.0off
480+620
0.5on 0.5off
480+620
0.25on 0.25off
480+620
1on 1off
22
Poland
425
cont.
425
1.0on 4.0off
425
0.5on 0.5off
425
0.5on 0.5off
425
1on 1off
23
Portugal
425
cont.
425
1.0on 5.0off
425
0.5on 0.5off
450
0.33on 1.0off
450
1on 1off
24
Russia
425
cont.
425
0.8on 3.2off
425
0.4on 0.4off
425
0.25on 0.25off
425
1on 1off
25
Saudi Arabia
425
cont.
425
1.2on 4.6off
425
0.5on 0.5off
425
0.25on 0.25off
425
1on 1off
26
Singapore
425
cont.
425*24
0.4on 0.2off
0.4on 2.0off
425
0.75on 0.75off
425
0.25on 0.25off
425
1on 1off
27
South Africa
400*33
cont.
400*33
0.4on 0.2off
0.4on 2.0off
400
0.5on 0.5off
400
0.25on 0.25off
400
1on 1off
1on 1off
28
Spain
29
Thailand
30
Turkey
31
UAE
425
cont.
425
1.5on 3.0off
425
0.2on 0.2off
425
0.25on 0.25off
425
400*50
cont.
400
1.0on 4.0off
400
0.5on 0.5off
400
0.3on 0.3off
400
1on 1off
450
cont.
450
2.0on 4.0off
450
0.5on 0.5off
450
0.2on 0.2off
0.6on 0.2off
450
1on 1off
350+440
cont.
400+450
0.4on 0.2off
0.4on 2.0off
400
0.375on
0.375off
400
0.4on 0.35off
0.225on 0.525off
400
1on 1off
Matrix SETU ATA211 System Manual
145
Dial Tone
Code Country
Ring Back Tone
Busy Tone
Error Tone1
Error Tone2
Freq.
Cadence
Freq.
Cadence
Freq.
Cadence
Freq.
Cadence
Freq.
Hz
second
Hz
second
Hz
second
Hz
second
Hz
Cadence
second
32
UK
350+440
cont.
400+450
0.4on 0.2off
0.4on 2.0off
400
0.375on
0.375off
400
0.4on 0.35off
0.225on 0.525off
400
1on 1off
33
USA/Canada
350+440
cont.
440+480
2.0on 4.0off
480+620
0.5on 0.5off
480+620
0.25on 0.25off
480+620
1on 1off
Note1:
Cont. = continuous
f1*f2: f1 is modulated by f2.
f1+f2: the juxtaposition of two freq. f1 and f2 without modulation.
Note 2:
The frequency and cadence for following tones are same and fixed for all countries:
• Confirmation Tone: 400Hz, 0.1 on - 0.1 off
• Programming Tone: 400Hz, 0.1 on - 0.9 off
• CCWT: 400Hz, 0.3 on 6.0 off
• Routing Tone: 400Hz, 0.1 on 1.9 off
Ring Cadences
Code Country
Frequency
(Hz)
CADENCE (In Seconds)
T1ON
T1OFF
T2ON
T2OFF
01
Australia
25
0.4
0.2
0.4
2.0
02
Belgium
25
1.0
3.0
03
Brazil
25
1.0
4.0
04
China
25
1.0
3.0
05
Egypt
25
2.0
4.0
06
France
25
1.5
3.5
07
Germany
25
3.5
5.5
0.79
1.1
08
Greece
25
1.0
4.0
09
India
25
0.4
0.2
0.4
2.0
10
Israel
25
2.0
3.0
11
Italy
25
1.0
4.0
12
Japan
25
1.0
2.0
13
Korea
25
1.0
3.0
14
Malaysia
25
2.0
3.0
15
New Zealand
25
2.0
3.0
16
Poland
25
2.0
3.0
17
Portugal
25
1.0
5.0
18
Russia
25
1.0
3.0
19
Singapore
25
0.4
0.2
0.4
2.0
20
South Africa
25
0.4
0.2
0.4
2.0
0.4
2.0
21
Spain
25
1.5
3.0
22
Thailand
25
2.0
3.0
23
UAE
25
2.0
3.0
24
UK
25
0.4
0.2
25
USA/Canada
25
2.0
4.0
146
Matrix SETU ATA211 System Manual
CADENCE (In Seconds)
Frequency
(Hz)
T1ON
T1OFF
T2ON
T2OFF
Australia
25
0.4
0.2
0.4
2.0
02
Belgium
25
1.0
3.0
03
Brazil
25
1.0
4.0
04
China
25
1.0
3.0
05
Egypt
25
2.0
4.0
06
France
25
1.5
3.5
07
Germany
25
3.5
5.5
0.79
1.1
08
Greece
25
1.0
4.0
09
India
25
0.4
0.2
0.4
2.0
10
Israel
25
2.0
3.0
11
Italy
25
1.0
4.0
12
Japan
25
1.0
2.0
13
Korea
25
1.0
3.0
14
Malaysia
25
2.0
3.0
15
New Zealand
25
2.0
3.0
16
Poland
25
2.0
3.0
17
Portugal
25
1.0
5.0
18
Russia
25
1.0
3.0
19
Singapore
25
0.4
0.2
0.4
2.0
20
South Africa
25
0.4
0.2
0.4
2.0
0.4
2.0
Code Country
01
21
Spain
25
1.5
3.0
22
Thailand
25
2.0
3.0
23
UAE
25
2.0
3.0
24
UK
25
0.4
0.2
25
USA/Canada
25
2.0
4.0
Where,
T1ON, T1OFF, are ON and OFF period for first ring cadence and T2ON, T2OFF, are ON and OFF period for
second ring cadence.
Waveform for 'ring', is Sine Wave.
Frequently Asked Questions (FAQs)
Q.1
Ans.
Which internet telephony (VoIP) protocols are supported by ATA211?
ATA211 supports Session Initiation Protocol (SIP) to make/receives calls on Internet network.
Q.2
Ans.
Can I make a call to another SIP terminal (e.g. Soft Phone running on PC) in my LAN network?
Yes. You can make a call to any SIP terminal in your LAN just by dialing an IP address of the SIP
terminal. If you are not comfortable in dialing an IP address, you can use 'Peer to Peer' feature which
allows you to dial the number instead an IP address for such type of applications.
Q.3
I have only one Internet connection for Internet surfing. Do I need another internet connection for making
VoIP calls using ATA211?
No. You do not need another internet connection to use ATA211. ATA211 has inbuilt router which enables
you to surf internet and making VoIP calls at the same time.
Ans.
Q.4
I am using the ATA211 to make VoIP calls and surf internet. I have connected my PC to LAN port of
Matrix SETU ATA211 System Manual
147
ATA211. Can I still surf the internet when ATA211 is power down?
Ans.
No. You can not surf Internet if ATA211 is power down. You must power ON the ATA211 to enable
Internet surfing on your PC. Else, connect the PC directly to the internet.
Q.5
I am using the ATA211 to make VoIP calls and surf internet. I have connected my PC to LAN port of
ATA211. Can I still make VoIP calls when my PC is shut down or not connected?
Yes. You can still make VoIP calls when your PC is shutdown or not connected.
Ans.
Q.6
Ans.
Q.7
Ans.
Q.8
Ans.
Q.9
Ans.
Q.10
Ans.
Q.11
Ans.
Q.12
Ans.
My Internet Service Provider (ISP) supports only PPPoE for internet services. Can I use ATA211 with my
ISP?
Yes. You need to configure PPPoE User-Id and PPPoE Password in ATA211 provided by your ISP.
My internet Service Provider (ISP) supports only DHCP to provide internet services. Can I use ATA211
with my ISP?
Yes. You need to enable the DHCP client in ATA211.
My internet service provider (ISP) provides me only dynamic IP address. Can I use ATA211 to make VoIP
calls and surf Internet at the same time?
Yes. Enable DHCP or PPPoE client in ATA211 as used by your ISP to provide internet services.
I do not have PC to access Web Jeeves for configuration. Can I change the IP address and subnet mask
of LAN/WAN port?
Yes. You can change the IP address and subnet mask of LAN/ WAN port of ATA211 if you do not have
PC to access Web Jeeves. You need to issue commands from the FXS port to change the IP address
and subnet mask.
I do not have PC to access Web Jeeves for configuration. Can I change the internet connection type of
ATA211 to DHCP or PPPoE or Static?
Yes. You can change the connection type by issuing command 37-#* from the FXS port of ATA211 and
configuring necessary parameters for the new connection type.
I do not have PC to access Web Jeeves for configuration. Can I know whether ATA211 is registered with
ITSP or not?
Yes. You can know the status of your SIP registration using LED provided on the enclosure of ATA211 or
by command to display registration status on the Phone connected to FXS port.
I have connected my PC to LAN port of ATA211. But, I am not able to access the Web Jeeves for
configuration.
Please ensure that the IP address of LAN port of ATA211 and IP address of your computer should be in
same subnet to enable Web Jeeves from your computer. If both the IP address is in the same subnet,
check for any error in the Ethernet cable which connects your computer to LAN port of ATA211.
Q.13
Ans.
Can I upgrade my ATA211 for new firmware?
Yes. You can upgrade the ATA211 for new firmware. To upgrade ATA211 for new firmware, please refer
“Software Upgrade”.
Q.14
Ans.
Can I upgrade the ATA211 for new firmware remotely?
Yes. If you know the public IP address of WAN port of ATA211, you can use the FTP server of ATA211 to
upgrade the firmware. Refer “Software Upgrade” topic.
Q.15
Ans.
If I forgot the password, can I still use the Web Jeeves for configuration?
Yes. But you need to set the password value to factory default.
148
Matrix SETU ATA211 System Manual
There are two important passwords for the configuration of ATA211 viz Admin Password and User
Password. Admin password protects the access to whole configuration while User password protects the
access to only few configuration of ATA211.
If you forgot the user password but you still have access to admin password, you can login to Web
Jeeves and change the user password. But, if you forgot the admin password, you need to default the
Password using access code '#***' from the Phone, connected to the ATA211.
Refer “Reinstate Factory Defaults” and “Configuring SETU ATA211” for more details.
Q.16
Ans.
I am not able to access the Web Jeeves since I forgot the IP address of LAN port of ATA211. How can I
know the IP address of LAN port?
You can use the system commands to know the IP address of LAN/WAN port of ATA211. Please ensure
that you have the SLT (compatible for CLI type) connected to the FXS port.
Q.17
Ans.
Can I make call to PSTN, GSM number using the FXO port of ATA211?
Yes. You can make call to any PSTN, GSM number using the FXO port of ATA211. You need to select the
FXO port by the command for 'Selective Trunk Access - FXO', #83 followed by the number to be dialed.
You can also do this by configuring the 'Outgoing Call Route' to 'FXO' in the Web page 'FXS Port', before
dialing the desired number or by setting 'Dialed Number Based Routing'.
Q.18
Ans.
Incoming calls on FXO port of ATA211 does not place on FXS port. Why?
Please check the destination route configured in Webpage 'FXO Port'.
Q.19
Ans.
Can I change the configuration of ATA211 to factory default?
Yes. You can change the configuration to factory default. Refer “Reinstate Factory Defaults” for
this information.
Q.20
Ans.
Can I select the SIP Trunk or FXO port to make OG call?
Yes. You can dial first the access code for the FXO, SIP1, SIP2 or SIP3 and then dial the required
number for OG call.
Q.21
Ans.
Can I use the ATA211 for Least Cost Routing (LCR) application?
Yes. You can do this by selecting 'Dialed Number based Routing' for parameter 'OG Call Route' in Web
page for 'FXS Port' . After selecting option for routing, program in the Webpage 'Dialed Number Table', the
numbers to be dialed and corresponding SIP Trunk or FXO port as Destination Route which is cheaper
for the call to be made.
Q.22
Ans.
Can I route the Incoming calls on SIP to FXO?
Yes. You can configure suitable routing option for 'Route the Incoming Calls' in the Webpage 'SIP Trunk'.
Refer “SIP Trunks”.
Matrix SETU ATA211 System Manual
149
Acronyms
CLI
Caller Line Identification
CPT
Call Progress Tone
CPTG
Call Progress Tone Generation
CWT
Call Waiting Tone
DHCP
Dynamic Host Configuration Protocol
DND
Do Not Disturb
DNS
Domain Name Service
DST
Daylight Savings Time
DTMF
Dual Tone Multi-Frequency
FEC
Forward Error Correction
FTP
File Transfer Protocol
GMT
Greenwich Mean Time
IC
Incoming call
IP
Internet Protocol
ISP
Internet Service Provider
ITSP
Internet Telephony Service Provider
ITU
International Telecommunication Union
LAN
Local Area Network
L2 VLAN
Layer2 Virtual Local Area Network
LED
Light Emitting Diode
MAC
Media Access Control
ms
Milliseconds
MPLS
Multi Protocol Label Switching
NAT
Network Address Traversal
NTP
Network Time Protocol
OG
Outgoing Call
PBX
Private Branch Exchange
PSTN
Public Switched Telephone Network
P2P
Peer to Peer
PPPoE
Point to Point Protocol over Ethernet
QoS
Quality of Service
RBT
Ring Back Tone
RFC
Request for Comments
RTP
Real Time Transport Protocol
SIP
Session Initiation Protocol
SLT
Single Line Telephone
SNTP
Simple Network Time Protocol
SOHO
Small Office Home Office
STUN
Simple Traversal of UDP over NAT
TCP
Transmission Control Protocol
TFTP
Trivial File Transfer Protocol
UDP
User Datagram Protocol
URI
Uniform Resource Identifier
URL
Universal Reference/Resource Locator
VAD
Voice Activity Detection
150
Matrix SETU ATA211 System Manual
WAN
Wide Area Network
VoIP
Voice Over Internet Protocol
Matrix SETU ATA211 System Manual
151
Features at a Glance
Description
Feature Code
To enter programming mode for Admin
#19-Admin Password
To enter programming mode for User
#18-User Password
To exit programming mode
0
Access Code for ‘Using Supplementary Services of Service Provider’,
that allows user to use both Gateway and Network types.
#0
Speed dialing
#9-Index Number
To default Login Password
#***
Making a new call
#81
Disconnect the call
#82
Selective Trunk Access-FXO
#83
Selective Trunk Access-SIP1
#84
Selective Trunk Access-SIP2
#85
Selective Trunk Access-SIP3
#86
152
Matrix SETU ATA211 System Manual
Product Specifications
Port Name Application
No. of
Connector Type
Ports
FXS Port
For connecting Analog Phone or Fax Machine
1
RJ 11
FXO Port
For accessing PSTN line
1
RJ 11
LAN Port
To connect a Computer
1
RJ 45, 10/100 Base T
WAN Port
To connect Ethernet cable router provided by service provider
1
RJ 45, 10/100 Base T
DC Jack
To connect the power adapter for DC supply voltage
1
DC Power Jack
VoIP and Networking Protocol
SIP (RFC 3261)
IPv4- Internet Protocol Version 4 (RFC 791)
ARP- Address Resolution Protocol (RFC 0826)
TCP- Transmission Control protocol (RFC 793)
UDP- User Datagram Protocol (RFC 768)
RTP- Real Time Protocol (RFC 1889)
RTCP- Real Time Control Protocol (RFC 1889)
SNTP- Simple Network Time Protocol
PPP- Point-to-Point Protocol (RFC 1661)
SDP
DHCP
HTTP
PPPoE
DTMF (RFC 2833)
DNS- Protocol (RFC 2136)
Outbound Proxy
STUN
NAT Keep Alive
VLAN- Virtual LAN (Layer2)
Voice Functionalities
Three SIP Trunks can be used
DTMF: Inband and Outband (RFC 2833)
Call Progress Tone Generation: Select as per the country
QoS (Layer3): RTP QoS and SIP QoS using Diffserv and ToS (Precedence)
Full Duplex Audio
Echo Cancellation: G. 168, with programmable tail length of 8, 16 and 32 msecs.
Forward Error Correction (FEC)
Voice Activity Detection (VAD)
Fax using T.38 and Pass Through
Flash Timer Programming
Voice Codecs
G.711 (a-Law and u-Law), G.729, G.723
Matrix SETU ATA211 System Manual
153
Telephony features
Voice Calls using SIP proxy and Voice calls without using SIP proxy (Peer-to-Peer Calling)
Call Waiting
Caller ID Blocking
Call Forwarding
3-Party conference
Call Transfer
Call Hold
Caller ID: Generation and Display
Answer supervision
Disconnect supervision
Speed Dialing
Do Not Disturb (DND)- Incoming calls can be rejected
Polarity Reversal- Useful when some billing machine is connected to ATA
Call Toggle- Used to toggle between active and held call
Auto PSTN fallback Support
If the Ethernet link is down or registration has failed, Route the calls to PSTN from FXO port.
Time Settings
Synchronizing with specific Time Server
Provisioning, Administration and Maintenance
Auto Configuration
Programming using Web Jeeves
Software Upgrade (Using FTP Server)
PCAP Trace
Programming using Phone of parameters such as:
• LAN IP Address
• WAN IP Address
LED Indication
LED for Power
LED for FXS
LED for FXO
LED for SIP1
LED for SIP2
Security
Password Protected Administrator and User settings
Dimension (W x H x D)
7.9x10.5x2.7 cm (3.1x4.1x1.1 inch)
154
Matrix SETU ATA211 System Manual
Unit Weight
0.45 kgs (1.10 lbs)
Shipping Weight
1 kg (2.20 lbs)
Power Supply
External Adapter: 12VDC@ 1.25Amp.
Power Consumption: 5W
Environmental
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Operating Humidity: 5-95% RH, Non-Condensing
Storage Temperature: -40°C to 85°C (-40°F to 185°F)
Storage Humidity: 0-95% RH, Non-Condensing
Matrix SETU ATA211 System Manual
155
System Commands
Command
Meaning
Allowed to?
#19-Admin Password
To enter programming code for Admin
Admin
#18-User Password
To enter programming code for User
User
0
To exit programming mode
Admin and
User
#0
Admin and
Access Code for ‘Using Supplementary Services of
Service Provider’, that allows user to use both Gateway User
and Network types.
11-WAN IP Address-#*
To program the WAN IP Address
Admin & User
12-LAN IP Address-#*
To program the LAN IP Address
Admin & User
13-Subnet Mask-#*
To program the Subnet Mask of WAN port
Admin & User
14-Subnet Mask-#*
To program the Subnet Mask of LAN port
Admin & User
15-Code-#*
To program the connection type of WAN port.
Admin & User
16-Code-#*
To enable/ disable 'L2 VLAN/ CoS' on WAN port.
Only Admin
21-Reverse Admin/User Password-#* To default the ATA211
Admin & User
31- #*
To display the WAN IP Address on SLT
Admin & User
32-#*
To display the LAN IP address on SLT
Admin & User
33-#*
To display the WAN Subnet Mask on SLT
Admin & User
34-#*
To display the LAN Subnet Mask on SLT
Admin & User
35-#*
To display the gateway address on SLT
Admin & User
36-#*
To display the Primary DNS address on SLT
Admin & User
37-#*
To display the connection type of WAN port on SLT
Admin & User
38-SIP Trunk-#*
To display the registration status of SIP
Admin & User
39-#*
To display the Secondary DNS address on SLT
Admin & User
51-Destination Number-#*
To program Call Forward-Unconditional number
Admin & User
52-Code-#*
Set/Cancel Call Forward-Unconditional
Admin & User
53-Destination Number-#*
To program Call Forward-When Busy number
Admin & User
54-Code-#*
Set/Cancel Call Forward-When Busy
Admin & User
55-Destination Number-#*
To program Call Forward-When No Reply number
Admin & User
56-Code-#*
Set/Cancel Call Forward-When No Reply
Admin & User
57-Timer-#*
Set Call Forward Timer
Admin & User
61-Code-#*
Set/Cancel DND
Admin & User
66-SIP Trunk-Code-#*
Send/Block Caller ID for SIP1, SIP2, SIP3
Only Admin
72-Code-#*
Set/Cancel Call Waiting
Admin & User
99-#*
Cancel all features
Admin & User
156
Matrix SETU ATA211 System Manual
Warranty Statement
Matrix warrants to its consumer purchaser any of its products to be free of defects in material, workmanship and
performance for a period of 15 months from date of manufacturing or 12 months from the date of installation
which ever is earlier.
During this warranty period, Matrix will at its option, repair or replace the product at no additional charge if the
product is found to have manufacturing defect. Any replacement product or part/s may be furnished on an
exchange basis, which shall be new or like-new, provided that it has functionality at least equal to that of the
product, being replaced. All replacement parts and products will be the property of Matrix. Parts repaired or
replaced will be under warranty throughout the remainder of the original warranty period only.
This limited warranty does not apply to:
1. Products that have been subjected to abuse, accident, natural disaster, misuse, modification, tampering,
faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the
documentation for the product or if the model or serial number has been altered, tampered with, defaced or
removed.
2. Products which have been damaged by lightning storms, water or power surges or which have been
neglected, altered, used for a purpose other than the one for which they were manufactured, repaired by
customer or any party without Matrix’s written authorization or used in any manner inconsistent with
Matrix’s instructions.
3. Products received improperly packed or physically damaged.
4. Products damaged due to operation of product outside the products’ specifications or use without
designated protections.
Warranty valid only if:
•
•
•
Primary protection on all the ports provided.
Mains supply is within limit and protected.
Environment conditions are maintained as per the product specifications.
Warranty Card:
•
When the product is installed, please return the warranty card with:
• Date, signature and stamp of the customer
• Date, signature and stamp of the channel partner
•
Matrix assumes that the customer agrees with the warranty terms even when the warranty card is not
signed and returned as suggested.
The Purchaser shall have to bear shipping charges for sending product to Matrix for testing/rectification. The
product shall be shipped to the Purchaser at no-charge if the material is found to be under warranty. The Purchaser
shall have to either insure the product or assume liability for loss or damage during transit.
Matrix reserves the right to waive off or make any changes in its warranty policy without giving any notice.
If Matrix is unable to repair or replace, as applicable, a defective product which is covered by Matrix warranty,
Matrix shall, within a reasonable time after being notified of the defect, refund the purchase price of the product
provided the consumer/purchaser returns the product to Matrix.
In no event will Matrix be liable for any damages including lost profits, lost business, lost savings, downtime or
delay, labor, repair or material cost, injury to person, property or other incidental or consequential damages arising
Matrix SETU ATA211 System Manual
157
out of use of or inability to use such product, even if Matrix has been advised of the possibility of such damages or
losses or for any claim by any other party.
Except for the obligations specifically set forth in this Warranty Policy Statement, in no event shall Matrix be liable
for any direct, indirect, special, incidental or consequential damages whether based on contract or any other legal
theory and where advised of the possibility of such damages.
Neither Matrix nor any of its distributors, dealers or sub-dealers makes any other warranty of any kind, whether
expressed or implied, with respect to Matrix products. Matrix and its distributors, dealers or sub-dealers specifically
disclaim the implied warranties of merchantability and fitness for a particular purpose.
This warranty is not transferable and applies only to the original consumer purchaser of the Product. Warranty shall
be void if the warranty card is not completed and registered with Matrix within 30 days of installation.
158
Matrix SETU ATA211 System Manual
Open Source Licensing Terms and Conditions
•
The firmware of this product also includes some of the Open-Source software released under GNU
General Public License (GPL) Version 2. Terms of this license is printed in full below.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.,
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change free
software--to make sure the software is free for all its users. This
General Public License applies to most of the Free Software
Foundation's software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is covered by
the GNU Lesser General Public License instead.) You can apply it to
your programs, too.
When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it
if you want it, that you can change the software or use pieces of it
in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the rights.
These restrictions translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know their
rights.
Matrix SETU ATA211 System Manual
161
We protect your rights with two steps: (1) copyright the software, and
(2) offer you this license which gives you legal permission to copy,
distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain
that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so
that any problems introduced by others will not reflect on the original
authors' reputations.
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making the
program proprietary. To prevent this, we have made it clear that any
patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and
modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains
a notice placed by the copyright holder saying it may be distributed
under the terms of this General Public License. The "Program", below,
refers to any such program or work, and a "work based on the Program"
means either the Program or any derivative work under copyright law:
that is to say, a work containing the Program or a portion of it,
either verbatim or with modifications and/or translated into another
language. (Hereinafter, translation is included without limitation in
the term "modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification are not
covered by this License; they are outside its scope. The act of
running the Program is not restricted, and the output from the Program
is covered only if its contents constitute a work based on the
Program (independent of having been made by running the Program).
Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's
source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the
notices that refer to this License and to the absence of any warranty;
and give any other recipients of the Program a copy of this License
along with the Program.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion
of it, thus forming a work based on the Program, and copy and
162
Matrix SETU ATA211 System Manual
distribute such modifications or work under the terms of Section 1
above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices
stating that you changed the files and the date of any change.
b) You must cause any work that
whole or in part contains or is
part thereof, to be licensed as
parties under the terms of this
you distribute or publish, that in
derived from the Program or any
a whole at no charge to all third
License.
c) If the modified program normally reads commands interactively
when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide
a warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this
License. (Exception: if the Program itself is interactive but
does not normally print such an announcement, your work based on
the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the Program,
and can be reasonably considered independent and separate works in
themselves, then this License, and its terms, do not apply to those
sections when you distribute them as separate works. But when you
distribute the same sections as part of a whole which is a work based
on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the
entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest
your rights to work written entirely by you; rather, the intent is to
exercise the right to control the distribution of derivative or
collective works based on the Program.
In addition, mere aggregation of another work not based on the Program
with the Program (or with a work based on the Program) on a volume of
a storage or distribution medium does not bring the other work under
the scope of this License.
3. You may copy and distribute the Program (or a work based on it,
under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable
source code, which must be distributed under the terms of Sections
1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than your
cost of physically performing source distribution, a complete
Matrix SETU ATA211 System Manual
163
machine-readable copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer
to distribute corresponding source code. (This alternative is
allowed only for noncommercial distribution and only if you
received the program in object code or executable form with such
an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to
control compilation and installation of the executable. However, as a
special exception, the source code distributed need not include
anything that is normally distributed (in either source or binary
form) with the major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless that component
itself accompanies the executable.
If distribution of executable or object code is made by offering
access to copy from a designated place, then offering equivalent
access to copy the source code from the same place counts as
distribution of the source code, even though third parties are not
compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense or distribute the Program is
void, and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such
parties remain in full compliance.
5. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify or
distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by
modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and
all its terms and conditions for copying, distributing or modifying
the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the
original licensor to copy, distribute or modify the Program subject to
these terms and conditions. You may not impose any further
restrictions on the recipients' exercise of the rights granted herein.
You are not responsible for enforcing compliance by third parties to
this License.
7. If, as a consequence of a court judgment or allegation of patent
164
Matrix SETU ATA211 System Manual
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot
distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you
may not distribute the Program at all. For example, if a patent
license would not permit royalty-free redistribution of the Program by
all those who receive copies directly or indirectly through you, then
the only way you could satisfy both it and this License would be to
refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under
any particular circumstance, the balance of the section is intended to
apply and the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to infringe any
patents or other property right claims or to contest validity of any
such claims; this section has the sole purpose of protecting the
integrity of the free software distribution system, which is
implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed
through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing
to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to
be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in
certain countries either by patents or by copyrighted interfaces, the
original copyright holder who places the Program under this License
may add an explicit geographical distribution limitation excluding
those countries, so that distribution is permitted only in or among
countries not thus excluded. In such case, this License incorporates
the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions
of the General Public License from time to time. Such new versions will
be similar in spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and "any
later version", you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number of
this License, you may choose any version ever published by the Free Software
Foundation.
10. If you wish to incorporate parts of the Program into other free
Matrix SETU ATA211 System Manual
165
programs whose distribution conditions are different, write to the author
to ask for permission. For software which is copyrighted by the Free
Software Foundation, write to the Free Software Foundation; we sometimes
make exceptions for this. Our decision will be guided by the two goals
of preserving the free status of all derivatives of our free software and
of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY
FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS
TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest
possible use to the public, the best way to achieve this is to make it
free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the
to attach them to the start of each source file
convey the exclusion of warranty; and each file
the "copyright" line and a pointer to where the
program. It is safest
to most effectively
should have at least
full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
166
Matrix SETU ATA211 System Manual
GNU General Public License for more details.
You should have received a copy of the GNU General Public License along
with this program; if not, write to the Free Software Foundation, Inc.,
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this
when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
This is free software, and you are welcome to redistribute it
under certain conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts
of the General Public License. Of course, the commands you use may be called
something other than `show w' and `show c'; they could even be mouse-clicks or
menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your
school, if any, to sign a "copyright disclaimer" for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
`Gnomovision' (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may
consider it more useful to permit linking proprietary applications with the
library. If this is what you want to do, use the GNU Lesser General
Public License instead of this License.
Matrix SETU ATA211 System Manual
167
168
Matrix SETU ATA211 System Manual
Index
Numerics
100rel 72
G
General Request Timer 72
A
AC Impedance 47, 55
I
Inter Digit Wait Timer 69
C
Call Release Timer 69
Call Transfer-Attended 109
Call Transfer-Blind 109
Class of Service 53, 65
Cloned 66
Connection Type
DHCP 63
PPPoE 63
Static 63
Current Date 141
Current Time 141
L
Language Selection 20
LEDs 6
D
Debug
configure system debug 97
Dialed Number Table
Configuring Dialed Number Table 74
Destination Route 40, 51, 77
Maximum Digits 29, 40, 51, 74, 77, 28, 40, 51, 74,
77
Number 25, 28, 40, 51, 74, 77, 81
DiffServe 65
DNS Setting
DNS Address 64
Static DNS 64
E
Echo Cancellation 47, 55
F
First Digit Wait Timer 69
Forced Maturity Timer 43
Forward Error Correction 69
O
Outgoing Calls 50
P
prioritization of traffic 65
R
Ring 21
Router's Public IP Address 71
Routing Tone 146
RTP QoS 66
S
SIP ID 24
SIP INVITE Timer 72
SIP Over TCP 72
SIP Provisional Timer 72
SIP/RTP Port
RTP Listening Port 72
SIP TCP Port 72
T
TCP NAT Keep Alive
Interval 71
Transfer Notification Timer 69
U
UDP NAT Keep Alive
Interval 71
Unique 66
V
VLAN header 65
VLAN/CoS Layer
RTP CoS 65
SIP CoS 65
Voice Activity Detection (VAD) 70
VoIP Silence Disconnect Timer 69
Volume 48, 56
W
Warranty Statement 157
Magyarországon a Matrix Telecom Ltd. képviselete,
Matrix termékek importőre, kizárólagos forgalmazója:
1095 Budapest, Mester u. 34.
Telefon: *218-5542, 215-9771, 215-7550, 216-7017, 216-7018
Fax: 218-5542 Mobil: 30 940-1970, 20 949-2688
E-mail: delton@delton.hu Web: www.delton.hu
Version 3, February 2011
www.matrixtelecom.hu