273 Branchport Ave.

Long Branch, N.J. 07740

631-2148 Thank you for using our products. www.wheelockinc.com INSTALLATION INSTRUCTIONS

SERIES RSS AND RSSP STROBE APPLIANCES

(WALL MOUNT VERSIONS)

Use this product according to this instruction manual. Please keep this instruction manual for future reference.

GENERAL:

Wheelock’s Series RSS and RSSP Strobes can provide a non-synchronized strobe appliance when connected directly to a Fire Alarm

Control Panel (FACP), or provide a synchronized strobe appliance when used in conjunction with a Sync Module (SM), Dual Sync

Module (DSM) or Power Supply (PS-12/24-8). The Series RSS and RSSP Strobe Appliances are UL Listed under Standard 1971

(Signaling Devices for the Hearing Impaired) for indoor fire protection service. These Strobes are listed for wall mount only, with the backboxes specified in these instructions (See Mounting Options). RSS models have an integrated Strobe Mounting Plate (SMP) that can be mounted to a single-gang, double-gang, 4” backbox, 100mm European backbox or SHBB surface backbox. The strobes use a

Xenon flashtube with solid state circuitry enclosed in a rugged Lexan  lens to provide maximum visibility and reliability for effective visible signaling. All inputs are polarized for compatibility with standard reverse polarity supervision of circuit wiring by the FACP.

NOTE: All CAUTIONS and WARNINGS are identified by the symbol . All warnings are printed in bold capital letters.

WARNING: THE RSS STROBE APPLIANCE IS A "FIRE ALARM DEVICE - DO NOT PAINT."

WARNING: READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO COMPLY WITH ANY OF THE

FOLLOWING INSTRUCTIONS, CAUTIONS AND WARNINGS COULD RESULT IN IMPROPER APPLICATION,

INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD

RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.

SPECIFICATIONS:

Model

Table 1: Ratings Per UL 1971

Regulated

Voltage

VDC/VRMS

Voltage

Range Limit

VDC/VRMS

Strobe

Candela

(CD)

Mounting

Options

Table 1A.

Audibles/Speakers for RSSP Strobe/Plate

Product Series

Multitone Appliances AMT, MT, MT4

A,B,C,D

Speakers

MB-G6/G10

ET-1010/1070/1080, ET70,

E7025/7070, E70

Chimes CH70

NOTES:

1. Strobes will produce 1 flash per second over the “Regulated

Voltage” range.

2. All models are UL Listed for indoor use with a temperature range of +32 o F to +120 o F (0 o C to +49 o C) and maximum humidity of 85% RH.

NOTE: THE MAXIMUM WIRE IMPEDANCE BETWEEN STROBES SHALL NOT EXCEED 35 OHMS. THE

MAXIMUM NUMBER OF STROBES ON A SINGLE NOTIFICATION APPLIANCE CIRCUIT SHALL NOT EXCEED 47.

WARNING: THESE APPLIANCES WERE TESTED TO THE OPERATING VOLTAGE LIMITS OF 16-33 VOLTS

FOR 24V MODELS AND 8-17.5 VOLTS FOR 12V MODELS USING FILTERED (DC) OR UNFILTERED FULL-WAVE

RECTIFIED (FWR). DO NOT APPLY 80% AND 110% OF THESE VOLTAGE VALUES FOR SYSTEM OPERATION.

WARNING: CHECK THE MINIMUM AND MAXIMUM OUTPUT OF THE POWER SUPPLY AND STANDBY

BATTERY AND SUBTRACT THE VOLTAGE DROP FROM THE CIRCUIT WIRING RESISTANCE TO DETERMINE

THE APPLIED VOLTAGE TO THE STROBES.

Copyright 2001 Wheelock, Inc. All rights reserved.

P84022 F

Sheet 1 of 6

Table 2A: Current Ratings (AMPS) for 24VDC Models

Rated Average Current

Voltage 2415W 2430W 2475W 24110W

MEAN RMS MEAN RMS MEAN RMS MEAN RMS

16.0VRMS ----- 0.105 ----- 0.141 ----- 0.262 ----- 0.330

24.0VRMS ----- 0.076 ----- 0.121 ----- 0.211 ----- 0.262

33.0VRMS ----- 0.070 ----- 0.105 ----- 0.185 ----- 0.229

Voltage 2415W

Rated Peak Current *

2430W

16.0VDC 0.185 0.264

2475W 24110W

0.456 0.584

24.0VDC 0.190

33.0VDC 0.195

16.0VRMS 0.182

24.0VRMS 0.185

33.0VRMS 0.197

0.269

0.274

0.259

0.268

0.286

Rated Inrush Current **

Voltage 2415W 2430W

16.0VDC 0.110 0.110

0.470 0.586

0.474 0.596

0.458 0.586

0.472 0.590

0.492 0.596

24.0VDC 0.165

33.0VDC 0.230

16.0VRMS 0.155

24.0VRMS 0.235

33.0VRMS 0.325

0.165

0.230

0.155

0.235

0.325

2475W 24110W

0.110 0.110

0.165 0.165

0.230 0.230

0.155 0.155

0.235 0.235

0.325 0.325

Table 2B: Current Ratings (AMPS) for 12VDC Models

Rated Average Current

Voltage 1215W

8.0VDC 0.220 0.246

12.0VDC 0.129 0.187

17.5VDC 0.099 0.163

8.0VRMS ----- 0.246

12.0VRMS ----- 0.198

17.5VRMS ----- 0.170

Rated Peak Current *

Voltage 1215W

8.0VDC 0.410

12.0VDC 0.426

17.5VDC 0.438

8.0VRMS 0.414

12.0VRMS 0.426

17.5VRMS 0.444

Rated Inrush Current **

Voltage 1215W

8.0VDC 0.081

12.0VDC 0.100

17.5VDC 0.145

8.0VRMS 0.098

12.0VRMS 0.140

17.5VRMS 0.190

* Rated average current is measured using mean value. ** The time duration for the peak current is 100 microseconds.

*** The time duration for the inrush current is 4 milliseconds.

WARNING: MAKE SURE THAT THE TOTAL AVERAGE CURRENT, TOTAL PEAK CURRENT AND TOTAL INRUSH CURRENT

REQUIRED BY ALL APPLIANCES THAT ARE CONNECTED TO THE SYSTEM’S PRIMARY AND SECONDARY POWER SOURCES, NAC

CIRCUITS, SM, DSM SYNC MODULES OR PS-12/24-8 POWER SUPPLY DO NOT EXCEED THE POWER SOURCES’ RATED CAPACITY

OR THE CURRENT RATINGS OF ANY FUSES ON THE CIRCUITS TO WHICH THESE APPLIANCES ARE WIRED. OVERLOADING

POWER SOURCES OR EXCEEDING FUSE RATINGS COULD RESULT IN LOSS OF POWER AND FAILURE TO ALERT OCCUPANTS

DURING AN EMERGENCY, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR

OTHERS.

P84022 F

Sheet 2 of 6

When calculating the total average, peak or inrush currents: Use Table 2A and 2B to determine the highest value of “Rated Average

Current” for an individual strobe (across the expected operating voltage range of the strobe) to determine the highest value of “Rated

Inrush Current” or “Rated Peak Current” (whichever is higher) of an individual strobe (across the expected voltage range of the strobe) then multiply the value by the total number of strobes; be sure to add the currents for any other appliances, including audible signaling appliances, powered by the same source and include any required safety factors.

If the inrush current or peak current exceeds the power supplies’ inrush capacity, the output voltage provided by the power supplies may drop below the listed voltage range of the appliances connected to the supply and the voltage may not recover in some types of power supplies. For example, an auxiliary power supply that lacks filtering at its output stage (either via lack of capacitance and/or lack of battery backup across the output) may exhibit this characteristic.

CAUTION: Strobes are not designed to be used on coded systems in which the applied voltage is cycled on and off.

LIGHT DISTRIBUTION:

Horizontal 15W

Table 3: Horizontal Plane

30W

Angle

(in deg.)

0

5

UL

Min.

15.0

13.5

Typ.

15W

24

24

UL

Min.

30.0

27.0

Typ.

30W

46

46

UL

Min.

75.0

67.5

75W

Typ.

75W

103

103

UL

Min.

110W

Typ.

110W

110.0

99.0

149

152

55

60

65

70

75

80

85

90

25

30

35

40

45

50

6.8

6.0

5.3

5.3

4.5

4.5

3.8

3.8

13.5

11.3

11.3

11.3

11.3

8.3

12

11

13

17

13

8

7

6

23

21

20

19

18

18

13.5

12.0

10.5

10.5

9.0

9.0

7.5

7.5

27.0

22.5

22.5

22.5

22.5

16.5

27

30

35

29

22

17

15

15

43

41

40

39

41

36

33.8

30.0

26.3

26.3

22.5

22.5

18.8

18.8

67.5

56.3

56.3

56.3

56.3

41.3

60

59

71

73

53

35

30

30

98

94

89

83

81

77

99.0

82.5

82.5

82.5

82.5

60.5

49.5

44.0

38.5

38.5

33.0

33.0

27.5

27.5

85

95

113

81

72

50

38

43

140

135

129

124

133

121

Vertical 15W

Table 3A: Vertical Plane

30W

Angle

(in deg.)

UL

Min.

Typ.

15W

UL

Min.

Typ.

30W

UL

Min.

0

5

15.0

13.5

24

24

30.0

27.0

46

46

75.0

67.5

75W

Typ.

75W

UL

Min.

110W

Typ.

110W

103

103

110.0

99.0

149

149

60

65

70

75

80

85

90

25

30

35

40

45

50

55

2.7

2.4

2.3

2.0

1.8

1.8

1.8

13.5

13.5

9.8

6.9

5.1

4.0

3.3

8

8

8

8

8

7

3

21

23

22

13

9

9

8

5.4

4.8

4.5

4.0

3.6

3.6

3.6

27.0

27.0

19.5

13.8

10.2

8.1

6.6

15

14

15

14

13

13

9

48

40

45

39

24

16

15

13.5

12.0

11.3

10.0

9.0

9.0

9.0

67.5

67.5

48.8

34.3

25.5

20.0

16.3

31

31

31

31

27

27

12

89

96

91

57

36

33

31

19.8

17.6

16.5

14.3

13.2

13.2

13.2

99.0

99.0

71.5

50.6

37.4

29.7

24.2

40

40

39

39

36

37

16

129

114

119

109

66

45

43

P84022 F

Sheet 3 of 6

WIRING INFORMATION:

Figure 1: Wiring Diagrams Figure 2.

STROBES

FROM PRECEDING

APPLIANCE, FACP

OR SYNC MODULE

TO NEXT SIGNAL

OR END OF LINE

RESISTOR (EOLR)

+ -

STROBE/PLATE

ASSEMBLY

AUDIBLE & VISIBLE

APPLIANCES

OPERATE

IN UNISON

FROM PRECEDING

APPLIANCE, FACP

OR SYNC MODULE

AUDIBLE VISIBLE

+ + -

RED BLK TO NEXT

APPLIANCE

OR EOLR

AUDIBLE VISIBLE

+ + -

STROBE/PLATE

ASSEMBLY

AUDIBLE & VISIBLE

APPLIANCES

OPERATE

INDEPENDENTLY

FROM PRECEDING

APPLIANCE, FACP

OR SYNC MODULE

TO NEXT

APPLIANCE

OR EOLR

FROM PRECEDING

APPLIANCE, FACP

OR SYNC MODULE

RED BLK

TO NEXT

APPLIANCE

OR EOLR

Refer to Sync Module instruction sheets SM (P83123), DSM (P83177) or PS-12/24-8 (P83862) for additional information.

MOUNTING OPTIONS:

1) All strobe appliances have in-out wiring terminals that accepts two #12 to 18 American Wire Gauge (AWG) wires at each screw terminal. Strip leads 3/8 inches and connect to screw terminals.

2) Break all in-out wire runs on supervised circuits to assure integrity of circuit supervision as shown in Figure 2.

Strobe/Plate assembly has two red leads and two black leads for in-out wiring. The polarity shown in the wiring diagrams is for the operation of the appliances. The polarity is reversed by the FACP during supervision.

WARNING: REMOVAL OF THE BLACK COVER AT THE BACK OF THE MOUNTING PLATE COULD RESULT IN SEVERE

ELECTRIC SHOCK.

CAUTION : The following figures show the maximum number of field wires (conductors) that can enter the backbox used with each mounting option. If these limits are exceeded, there may be insufficient space in the backbox to accommodate the field wires and stresses from the wires could damage the product.

Although the limits shown for each mounting option comply with the National Electrical Code (NEC), Wheelock recommends use of the largest backbox option shown and the use of approved stranded field wires, whenever possible, to provide additional wiring room for easy installation and minimum stress on the product from wiring.

A

FLUSH MOUNTING

STD. SINGLE-GANG

BACKBOX 2" DEEP

#6-32 X 5/8"

SCREWS

B

FLUSH OR SURFACE MOUNT

4" SQ. X 1-1/2" DEEP BACKBOX

OR 100m X 37.5mm

EUROPEAN BACKBOX

STROBE MOUNTING

PLATE (SMP)

#8-32 X 3/4"

SCREWS

C

FLUSH OR SURFACE MOUNT

DOUBLE-GANG X 2-1/4"

DEEP BACKBOX

#6-32 X 5/8"

SCREWS

STROBE MOUNTING

PLATE (SMP)

BEAUTY PLATE (SUPPLIED)

MAXIMUM NUMBER OF CONDUCTORS

AWG #18 AWG #16 AWG #14 AWG #12

4 4 4 4

D SURFACE MOUNTING

SHALLOW SURFACE

BACKBOX (SHBB)

#8-32 X 3/4"

SCREWS

STROBE MOUNTING

PLATE (SMP)

BEAUTY PLATE (SUPPLIED)

MAXIMUM NUMBER OF CONDUCTORS

AWG #18 AWG #16 AWG #14 AWG #12

4 4 4 4

BEAUTY PLATE (SUPPLIED)

MAXIMUM NUMBER OF CONDUCTORS

AWG #18 AWG #16 AWG #14 AWG #12

4 4 4 4

E

APPLIANCE

FLUSH MOUNTING

STANDARD 4" X 2-1/8"

DEEP BACKBOX

F

SURFACE MOUNTING

BACKBOX (SBL-2)

APPLIANCE

STROBE MOUNTING

PLATE (SMP)

BEAUTY PLATE (SUPPLIED)

MAXIMUM NUMBER OF CONDUCTORS

AWG #18 AWG #16 AWG #14 AWG #12

4 4 4 4

MAXIMUM NUMBER OF CONDUCTORS

AWG #18 AWG #16 AWG #14 AWG #12

8 8 8 8

MAXIMUM NUMBER OF CONDUCTORS

AWG #18 AWG #16 AWG #14 AWG #12

8 8 8 8

Figures E and F are shown with optional 6” bell. See Table 1A for other possible appliance combinations.

P84022 F

Sheet 4 of 6

MOUNTING PROCEDURES:

CAUTION : Check that the installed product will have sufficient clearance and wiring room prior to installing backboxes and conduit, especially if sheathed multiconductor cable or 3/4" conduit fittings are used.

1. RSS models have an integrated Strobe Mounting Plate (SMP).

2. The Strobe Mounting Plate (SMP) must be oriented correctly when it is mounted to the backbox. Turn the SMP so that the arrow above the words “Horizontal Strobe” points to the top side of the SMP.

3. RSS models can be flush mounted to a standard single-gang backbox (Figure A), 4” or 100mm backbox (Figure B) or doublegang backbox (Figure C). RSS models can also be surface mounted to a 4” or 100mm backbox (Figure B), double-gang backbox

(Figure C) or the SHBB (Figure D). RSSP models can be flush mounted to a 4” backbox (Figure E) or surface mounted to a

SBL-2 backbox (Figure F).

4. Mount the SMP first to the backbox. Next slide the Beauty Plate over the SMP until the 2 snaps of the Beauty Plate engage with the SMP.

5. The Beauty Plate can be removed from the strobe assembly once engaged. First, gently insert a screwdriver into one of the slots located on the top and bottom edges of the Beauty Plate. Second, gently pull away from the wall with the inserted screwdriver to disengage the snap. Third, repeat the first and second steps for the second slot. Finally, gently lift the Beauty Plate away from the SMP.

6. Mounting hardware for each mounting option is supplied.

7. Conduit entrances to the backbox should be selected to provide sufficient wiring clearance for the installed product.

8. When terminating field wires, do not use more lead length than required. Excess lead length could result in insufficient wiring space for the signaling appliance.

9. Use care and proper techniques to position the field wires in the backbox so that they use minimum space and produce minimum stress on the product. This is especially important for stiff, heavy gauge wires and wires with thick insulation or sheathing.

10. Do not pass additional wires (used for other than the signaling appliance) through the backbox. Such additional wires could result in insufficient wiring space for the signaling appliance.

WARNING: WHEN INSTALLING STROBES IN AN OPEN OFFICE OR OTHER AREAS CONTAINING PARTITIONS OR

OTHER VIEWING OBSTRUCTIONS, SPECIAL ATTENTION SHOULD BE GIVEN TO THE LOCATION OF THE STROBES SO

THAT THEIR OPERATING EFFECT CAN BE SEEN BY ALL INTENDED VIEWERS, WITH THE INTENSITY, NUMBER, AND

TYPE OF STROBES BEING SUFFICIENT TO MAKE SURE THAT THE INTENDED VIEWER IS ALERTED BY PROPER

ILLUMINATION, REGARDLESS OF THE VIEWER'S ORIENTATION. FAILURE TO DO SO COULD RESULT IN PROPERTY

DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.

RSS/RSSP-24110 strobe models are Listed for use in sleeping or non-sleeping areas when installed in accordance with appropriate

NFPA Standards and the Authority Having Jurisdiction.

WARNING: INSTALLATION OF WHEELOCK 110 CANDELA STROBE PRODUCTS IN SLEEPING AREAS SHOULD BE WALL

MOUNTED AT LEAST 24" BELOW THE CEILING AS FOLLOWS: (1) THE ON-AXIS (DIRECTLY IN FRONT OF LENS) LIGHT

OUTPUT SHOULD BE DIRECTED AT THE EYE-LIDS OF THE SLEEPING PERSON, E.G. PILLOW END OF BED, BED HEAD; (2)

NO PART OF THE BED SHALL BE MORE THAN SIXTEEN (16) FEET FROM THE STROBE NOTIFICATION APPLIANCE.

INSTALLERS MUST ADVISE OWNERS AND OPERATORS OF BUILDINGS WITH SLEEPING OCCUPANTS, E.G. HOTELS AND

MOTELS, TO WARN GUESTS, RESIDENTS AND EMPLOYEES TO NOT MOVE THE BED LOCATION TO A POSITION

VIOLATING POINTS (1) AND (2) ABOVE OR SERIOUS INJURY AND/OR LOSS OF LIFE MAY OCCUR DURING A FIRE

EMERGENCY.

WARNING: A SMALL POSSIBILITY EXISTS THAT THE USE OF MULTIPLE STROBES WITHIN A PERSON'S FIELD OF

VIEW, UNDER CERTAIN CIRCUMSTANCES, MIGHT INDUCE A PHOTO-SENSITIVE RESPONSE IN PERSONS WITH EPILEPSY.

STROBE REFLECTIONS IN A GLASS OR MIRRORED SURFACE MIGHT ALSO INDUCE SUCH A RESPONSE. TO MINIMIZE

THIS POSSIBLE HAZARD, WHEELOCK STRONGLY RECOMMENDS THAT THE STROBES INSTALLED SHOULD NOT

PRESENT A COMPOSITE FLASH RATE IN THE FIELD OF VIEW WHICH EXCEEDS FIVE (5) Hz AT THE OPERATING

VOLTAGE OF THE STROBES. WHEELOCK ALSO STRONGLY RECOMMENDS THAT THE INTENSITY AND COMPOSITE

FLASH RATE OF INSTALLED STROBES COMPLY WITH LEVELS ESTABLISHED BY APPLICABLE LAWS, STANDARDS,

REGULATIONS, CODES AND GUIDELINES.

NOTE : NFPA 72/ANSI 117.1 conform to ADAAG Equivalent Facilitation Guidelines in using fewer, higher intensity strobes within the same protected area.

CAUTION : Check the installation instructions of the manufacturers of other equipment used in the system for any guidelines or restrictions on wiring and/or locating Notification Appliance Circuits (NAC) and notification appliances. Some system communication circuits and/or audio circuits, for example, may require special precautions to assure immunity from electrical noise

(e.g. audio crosstalk).

ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM WHEELOCK MANUALS OR OTHER DOCUMENTS

DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR ANY OTHER USE,

INCLUDING DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION, INSTALLATION AND TESTING IS USED AT

THE SOLE RISK OF THE USER AND WHEELOCK WILL NOT HAVE ANY LIABILITY FOR SUCH USE.

P84022 F

Sheet 5 of 6

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna, 2) Increase the separation between the equipment and receiver, 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and 4) Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT: READ SEPARATE "GENERAL INFORMATION" SHEET FOR INFORMATION ON THE PLACEMENT,

LIMITATIONS, INSTALLATION, FINAL CHECKOUT, AND PERIODIC TESTING OF NOTIFICATION APPLIANCES.

Limited Warranty

Wheelock products must be used within their published specifications and must be PROPERLY specified, applied, installed, operated, maintained and operationally tested in accordance with these instructions at the time of installation and at least twice a year or more often and in accordance with local, state and federal codes, regulations and laws. Specification, application, installation, operation, maintenance and testing must be performed by qualified personnel for proper operation in accordance with all of the latest National

Fire Protection Association (NFPA), Underwriters' Laboratories (UL), Underwriters' Laboratories of Canada (ULC), National

Electrical Code (NEC), Occupational Safety and Health Administration (OSHA), local, state, county, province, district, federal and other applicable building and fire standards, guidelines, regulations, laws and codes including, but not limited to, all appendices and amendments and the requirements of the local authority having jurisdiction (AHJ). Wheelock products when properly specified, applied, installed, operated, maintained and operationally tested as provided above are warranted against mechanical and electrical defects for a period of three years from date of manufacture (as determined by date code). Correction of defects by repair or replacement shall be at Wheelock's sole discretion and shall constitute fulfillment of all obligations under this warranty. THE

FOREGOING LIMITED WARRANTY SHALL IMMEDIATELY TERMINATE IN THE EVENT ANY PART NOT FURNISHED BY

WHEELOCK IS INSTALLED IN THE PRODUCT. THE FOREGOING LIMITED WARRANTY SPECIFICALLY EXCLUDES ANY

SOFTWARE REQUIRED FOR THE OPERATION OF OR INCLUDED IN A PRODUCT. WHEELOCK MAKES NO REPRESENTATION OR

WARRANTY OF ANY OTHER KIND, EXPRESS, IMPLIED OR STATUTORY WHETHER AS TO MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE OR ANY OTHER MATTER.

USERS ARE SOLELY RESPONSIBLE FOR DETERMINING WHETHER A PRODUCT IS SUITABLE FOR THE USER'S PURPOSES, OR

WHETHER IT WILL ACHIEVE THE USER'S INTENDED RESULTS. THERE IS NO WARRANTY AGAINST DAMAGE RESULTING

FROM MISAPPLICATION, IMPROPER SPECIFICATION, ABUSE, ACCIDENT OR OTHER OPERATING CONDITIONS BEYOND

WHEELOCK'S CONTROL.

SOME WHEELOCK PRODUCTS CONTAIN SOFTWARE. WITH RESPECT TO THOSE PRODUCTS, WHEELOCK DOES NOT

WARRANTY THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE OR THAT THE SOFTWARE

WILL MEET ANY OTHER STANDARD OF PERFORMANCE, OR THAT THE FUNCTIONS OR PERFORMANCE OF THE SOFTWARE

WILL MEET THE USER'S REQUIREMENTS. WHEELOCK SHALL NOT BE LIABLE FOR ANY DELAYS, BREAKDOWNS,

INTERRUPTIONS, LOSS, DESTRUCTION, ALTERATION, OR OTHER PROBLEMS IN THE USE OF A PRODUCT ARISING OUT OF OR

CAUSED BY THE SOFTWARE.

THE LIABILITY OF WHEELOCK ARISING OUT OF THE SUPPLYING OF A PRODUCT, OR ITS USE, WHETHER ON WARRANTIES,

NEGLIGENCE, OR OTHERWISE, SHALL NOT IN ANY CASE EXCEED THE COST OF CORRECTING DEFECTS AS STATED IN THE

LIMITED WARRANTY AND UPON EXPIRATION OF THE WARRANTY PERIOD ALL SUCH LIABILITY SHALL TERMINATE.

WHEELOCK IS NOT LIABLE FOR LABOR COSTS INCURRED IN REMOVAL, REINSTALLATION OR REPAIR OF THE PRODUCT BY

ANYONE OTHER THAN WHEELOCK OR FOR DAMAGE OF ANY TYPE WHATSOEVER, INCLUDING BUT NOT LIMITED TO, LOSS

OF PROFIT OR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF

THE PURCHASER AND THE EXCLUSIVE LIABILITY OF WHEELOCK.

IN NO CASE WILL WHEELOCK'S LIABILITY EXCEED THE PURCHASE PRICE PAID FOR A PRODUCT.

Limitation of Liability

WHEELOCK'S LIABILITY ON ANY CLAIM OF ANY KIND, INCLUDING NEGLIGENCE AND BREACH OF WARRANTY, FOR ANY

LOSS OR DAMAGE RESULTING FROM, ARISING OUT OF, OR CONNECTED WITH THIS CONTRACT, OR FROM THE

MANUFACTURE, SALE, DELIVERY, RESALE, REPAIR OR USE OF ANY PRODUCT COVERED BY THIS ORDER SHALL BE LIMITED

TO THE PRICE APPLICABLE TO THE PRODUCT OR PART THEREOF WHICH GIVES RISE TO THE CLAIM. WHEELOCK'S LIABILITY

ON ANY CLAIM OF ANY KIND SHALL CEASE IMMEDIATELY UPON THE INSTALLATION IN THE PRODUCT OF ANY PART NOT

FURNISHED BY WHEELOCK. IN NO EVENT SHALL WHEELOCK BE LIABLE FOR ANY CLAIM OF ANY KIND UNLESS IT IS

PROVEN THAT OUR PRODUCT WAS A DIRECT CAUSE OF SUCH CLAIM. FURTHER, IN NO EVENT, INCLUDING IN THE CASE OF A

CLAIM OF NEGLIGENCE, SHALL WHEELOCK BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO

NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE PRECEDING

LIMITATION MAY NOT APPLY TO ALL PURCHASERS.

10/01

P84022 F

Sheet 6 of 6