Westinghouse LCM-15V5 Specifications

15” LCD MONITOR
Model LCM-15v5
Table of Contents
IMPORTANT PRODUCT SAFETY INSTRUCTIONS ...................................................................... 2
CLEANING THE LCD MONITOR ................................................................................................................. 4
SAFETY GUIDELINES ............................................................................................................................... 5
FCC COMPLIANCE STATEMENT .............................................................................................................. 5
INSTALLATION...................................................................................................................................... 6
1.
2.
3.
4.
ATTACHING THE BASE STAND TO THE LCD MONITOR .................................................................... 6
CONNECT THE VGA AND AUDIO CABLES ........................................................................................ 6
CONNECT THE POWER CABLE ......................................................................................................... 6
TURN THE POWER ON ..................................................................................................................... 6
OSD MENU FUNCTIONS...................................................................................................................... 7
OSD MENUS ........................................................................................................................................... 8
BACKLIGHT CONTROL...................................................................................................................... 9
DISPLAY MODES ..................................................................................................................................... 9
9IMAGE PROBLEM ........................................................................................................................ 10
NO SIGNAL INPUT ................................................................................................................................... 10
OUT OF RANGE ..................................................................................................................................... 10
APPENDIX ..............................................................................................................................................11
SPECIFICATIONS .................................................................................................................................... 11
TROUBLESHOOTING .............................................................................................................................. 12
No Power.......................................................................................................................................... 12
No Image.......................................................................................................................................... 12
Power is ON but no Screen Image ................................................................................................... 12
“Out Of Range”................................................................................................................................ 12
Fuzzy Image..................................................................................................................................... 12
Image Too Bright or Too Dark ......................................................................................................... 12
Distorted Image................................................................................................................................ 12
Image is Not Centered (size is not scaled correctly)........................................................................ 12
Colors are Not Correct. .................................................................................................................... 12
No Sound.......................................................................................................................................... 12
Mounting the LCD Monitor on a Wall............................................................................................. 13
Additional Questions........................................................................................................................ 13
1
IMPORTANT PRODUCT SAFETY
INSTRUCTIONS
Read carefully and follow all warnings and instructions in this User's Manual and those
marked on the product before you use the monitor. Failing to follow these warnings can result
in personal injury or damage to the monitor. Keep this User’s Manual in a convenient location
for future reference. Important: Save the original box and all packing material for future
shipping needs.
Proper Handling of the Monitor
Always handle the LCD monitor with care. Avoid touching the LCD screen. Skin oils are
difficult to remove.
Always position the LCD monitor on a stable and level surface. Unstable surfaces can cause
the monitor to topple and fall, resulting in possible damage or injury.
Avoid exposing the monitor to direct sunlight or high temperatures, which can damage or
shorten its useful life. Do not place it near heat sources such as radiators, heat registers, or
other appliances that generate heat. Orient the monitor away from direct sunlight to reduce
glare.
Avoid exposing the monitor to rain, water, moisture or high humidity. Do not place it near
basins or sinks where it may come in contact with water.
Never place heavy or sharp objects on the LCD monitor, video cable, or power cord.
Overloading Outlets
Do not overload electrical power sources when installing the LCD monitor. Overloading wall
outlets, circuits, or extension cords can result in overheating, fire, or electric shock. Use only
grounded or polarized outlets.
Power Cord Protection
Minimize wear on the power supply cord. The power supply cord should be routed away from
foot traffic and contact with other objects. Do not route the power cord under rugs or carpeting.
The cord should never be severely bent, pinched, or twisted. Periodically inspect the power
cord and each end of the cord for wear or damage. Unplug and replace the cord if it is
damaged.
Ventilation
Slots and openings on the cabinet are provided for ventilation purposes. To ensure reliable
operation of the product and to protect it from overheating, these openings must not be
blocked or covered. Keep the LCD monitor a minimum of four (4) inches away from any wall to
assure sufficient airflow and ventilation. Increased temperatures may cause fire or device
failure.
2
To assure proper ventilation, do not block the openings by placing the monitor on a bed, sofa,
rug or other similar surface. Do not place it in a built-in installation, such as a bookcase or
enclosed rack, unless proper ventilation is provided.
Other Notices and Precautions
Caution: Never remove the rear cover. There are no user serviceable parts inside. The LCD
monitor contains high voltage parts. You may be seriously injured if you touch them.
Do not attempt repairs yourself. The warranty does not cover repairs or attempted repairs by
anyone not authorized by Westinghouse Digital. Refer all servicing and repairs to qualified
service personnel.
If the monitor begins to emit smoke, an abnormal noise, or a strange odor, immediately turn it
off and unplug the power cord. Contact the Westinghouse Service Center.
If the LCD Monitor will not be used for an extended period of time, unplug the power cord.
3
Cleaning the LCD Monitor
•
•
MAKE SURE THE LCD MONITOR IS TURNED OFF
NEVER SPRAY OR POUR LIQUID DIRECTLY ONTO THE SCREEN OR CASE
To Clean the Screen:
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2. If it still is not clean, use a small amount of non-ammonia, non-alcohol based glass cleaner on a
clean, soft, lint-free cloth to clean the screen.
To Clean the Case:
1. Use a soft, dry cloth.
2. If it still is not clean, use a small amount of non-ammonia, non-alcohol based, mild non-abrasive
detergent on a clean, soft, lint-free cloth to clean the surface.
Disclaimer
Westinghouse Digital does not recommend the use of any ammonia or alcohol-based cleaners on the
LCD screen or case. Some chemical cleaners have been reported to damage the screen and/or
display case. Westinghouse Digital will not be liable for damage resulting from the use of any
ammonia or alcohol-based cleaners.
4
Safety Guidelines
Warning: This device must be operated with the original power supply, part number ADP-60CF A.
CAUTION: The power supply outlet should be located near the equipment and should be easily accessible.
Use a power cable that is properly grounded. Always use the appropriate AC cord that is certified for the
individual country. Some examples are listed below:
USA.................UL
Switzerland ..... SEV
Canada.............CSA
Britain ............. BASE/BS
Germany..........VDE
Japan ............... Electric Appliance Control Act
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The power cord set for this unit has been enclosed and has been selected according to the country of destination
and must be used to prevent electric shock. Use the following guidelines if it is necessary to replace the original
cord, or if it is not enclosed.
The female receptacle of the power cord must meet IEC-60320 requirements and should look like Figure A1
below:
Figure A1
Figure A2
For the United States and Canada
In the United States and Canada the male end of the plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA
Labeled. For units that are mounted on a desk or table, type SVT or SJT power cords may be used. If the monitor
is placed on the floor, only SJT type cords may be used. The power cord must be selected according to the
current rating for your unit. Please consult the table below for the selection criteria for power cords used in the
United States and Canada.
Cord Type
SJT
SVT
Size of Conductors in Cord Maximum Current Rating of Unit
18 AWG
16 AWG
14 AWG
18 AWG
17 AWG
10 Amps
12 Amps
12 Amps
10 Amps
12 Amps
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and may cause harmful interference to radio
communications if not installed and used in accordance with the instructions. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
•
•
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced technician for help.
FCC Warning:
To assure continued FCC compliance, the user must use a grounded power supply cord and the
provided shielded cables. Any unauthorized changes or modifications not expressly approved by
Westinghouse Digital could void the user's authority to operate this device.
5
Installation
Congratulations on your purchase of a Westinghouse 15” LCD monitor. Sleek and practical,
this lightweight and wall-mountable LCD monitor delivers a crisp and clear display optimized
for 1024 x 768 resolution.
Package Contents
•
•
•
•
LCD Monitor (15”)
Detachable LCD Base Stand
Cables
o AC/DC Power Supply Adapter and Cord
o VGA (HD15) Male – Male Cable
o 3.5 mm Male – Male Stereo Audio Cable
Literature
o User’s Manual
o Warranty Card
1. Attaching the Base Stand to the LCD Monitor
Attach the base stand to the LCD monitor stand neck. Align the holes and tabs; press in and
snap into place. To remove the base stand, press the tabs on the bottom of the stand neck
and remove the base.
2. Connect the VGA and Audio Cables
Connect a VGA cable (to the connector labeled “D-SUB”) and an audio cable (to the connector
labeled “LINE-IN”) from the back panel of the LCD monitor to your PC.
3. Connect the Power Cable
Connect the DC power adapter cord to the monitor (to the connector labeled “DC-IN”) and
then connect the female AC power cord to the adapter. Plug the AC power cord into a properly
grounded AC outlet.
4. Turn the Power On
Press the power button on the front of the LCD monitor. The LED light will turn green if a
signal input is detected or it will be orange if no input is detected.
Auto Adjust
Although a computer can detect the new monitor with the built-in VESA Plug & Play feature,
the Auto Adjust function can be used to enhance the display. To perform the Auto Adjust:
Turn on the computer and monitor. Press the “Auto” button to start Auto Adjust. The LCD
monitor will perform the Auto Adjust process automatically for 10 seconds and you will notice
the image change after it has been adjusted.
6
OSD Menu Functions
1
Power Switch
LED
2
Auto
3
Exit/
4
┼/
5
―/
6
Menu
7
Turbo
Input / Turbo
Speaker
8
Power On/Off
Power Indicator
Green: Normal
Orange: Power Saving
Off: Power Off
Automatically optimizes positions, phase & clock (only
when the OSD is not on)
Exit the OSD menu
OSD selection and adjustment
Quick Brightness adjustment
OSD selection and adjustment
Quick Contrast adjustment
Enter the OSD menu
Access the OSD sub-menu & selection
Quick Brightness switching
D-Sub (VGA)
All the function settings for the LCD monitor are controlled via the control keys located on the
bottom part of the front panel. To display the OSD main menu, press the “Menu” keypad
button on the control keys. (Note: The OSD menu display will disappear automatically after
approximately 10 seconds, if no action is taken.)
The LCD monitor has been adjusted to optimal settings before shipment. Adjustments to the
monitor settings can be made using the OSD menu.
Press the “Menu” keypad button to display the OSD menu.
Press the “+” or “-“ keypad button to select the function to be adjusted.
Press the “Menu” keypad button to enter the OSD sub-menu to be adjusted.
Press the “+” or “-“ keypad button to change the setting of the function.
To exit the OSD menu or go back to the previous action, press the “Exit” keypad button. It
automatically will save any changes that have been made.
Repeat the steps above to change the setting of other functions. The following is a list of the
OSD sub-menus for the LCD monitor.
7
OSD Menu
Image
Audio
Color
Language
Sub-Menu
Description and Function
Brightness
Adjust the brightness of the screen
Contrast
Adjust the contrast of the image
Clock
Adjust the clock pulse of the image
Phase
Adjust the focus of the image
H. Position
Move the image left and right on the screen
V. Position
Move the image up and down on the screen
Sharpness
Adjust the picture sharpness of lower resolutions
Volume
Adjust the audio volume
Mute
Turn on or off audio muting
9300K
Set the color temperature to 9300K white color
7500K
Set the color temperature to 7500K white color
6500K
Set the color temperature to 6500K white color
User/Red
Adjust red gain
User/Green
Adjust green gain
User/Blue
Adjust blue gain
English
Select the OSD language
Français
Italiano
Deutsch
Español
日本語
简体中文
繁體中文
Settings
OSD Timeout
Adjust OSD display time setting
OSD Position
Move the OSD display position to one of the following 5 positions
within the overall screen.
1
2
3
4
Input Source
5
Auto Setting
Adjust clock, phase and positions automatically
Recall
Restore to factory settings
Analog
Select Analog input source:
8
Language Selection
Color Temp. Selection
Volume Adjustment
Image Adjustment
Settings
Input Source
Audio Current Status
Source Resolution & Frequency
Color Temp. Status
Input Source Status
Backlight Control
Display Modes
The monitor backlighting can be controlled by using the Turbo button on the keypad. There
are 3 modes: Economy, Text and Picture. To toggle between these modes, press the Turbo
key until the mode you desire is selected. These modes automatically change the backlighting
levels between bright, brighter and brightest.
9
Image Problem
No Signal Input
If there is no source connected to the monitor, the following error message will be displayed:
Out of Range
If the monitor settings are not compatible with the PC or out of range of the LCD monitor, the
following error message will be displayed:
10
Appendix
Specifications
Panel
Type
15" Color TFT LCD Panel
Optimum Resolution
1024 x 768
Response Time
16 ms
Contrast Ratio
450:1
Maximum Brightness
370 Nits
Viewing Angles
120° (H) / 110° (V)
Color Saturation
72% TBD
Wall/Arm Mount
Physical
75mm VESA®
Input Signal
Video
HD-15 pin mini D-Sub (VGA connector)
Audio
3.5mm Mini-Stereo jack male-male
Built-in audio amplifier and speakers, 2.5 watts * 2 channels
Speaker Output
Power
Voltage
100-240 VAC, 50/60 Hz (auto switch), 1.5A
Operating Conditions
Temperature
32° F to +95° F (0° C to +35° C)
Humidity
20% to 80% (no condensation)
Altitude
Up to 3,000 meters
Temperature
-4° F to +130° F (-20° C to +55° C)
Humidity
20% to 85% (no condensation)
Altitude
Up to 12,000 meters
Dimensions
Physical
16.1 (w) x 15.9 (h) x 4.9 (d) in
Weight
Net
5.7 lb (2.6 kg)
Storage Conditions
Regulations
FCC-B, UL, CSA (CUL), Energy Star®, Plug & Play
Lamp Life
40,000 hours
11
Troubleshooting
No Power
•
•
•
Make sure the DC cord is plugged into the back of the LCD monitor.
Make sure the AC power cord is securely connected to the AC socket.
Plug another electrical device (like a radio) to the power outlet to verify that the outlet is
supplying the proper voltage.
No Image
•
•
Make sure the power button is ON.
Check whether the LCD monitor and computer power cords are plugged in and check
the power supply.
Power is ON but no Screen Image
•
•
Adjust the brightness and contrast levels.
Make sure the VGA cable is securely connected to both the computer and monitor.
“Out Of Range”
•
Check the computer image output resolution and frequency and compare the value with
the preset values of the computer’s graphics card.
Fuzzy Image
•
Adjust the Phase setting on the monitor.
Image is Too Bright or Too Dark
•
•
•
•
Adjust the brightness and contrast levels using the OSD.
Make sure that the computer is not displaying an irregular image.
Check the VGA connection between the computer and LCD monitor.
Perform Auto Adjust.
Distorted Image
•
•
Reset the LCD monitor by performing the “Recall” function using the OSD.
Remove extra accessories (such as a VGA extension cord).
Image is Not Centered (size is not scaled correctly)
•
Perform Auto Adjust.
•
•
Adjust the horizontal and/or vertical position of the image using the OSD.
Check the image size setting.
Colors are Not Correct
•
Adjust the color setting using the OSD.
No Sound
•
Check the audio connection.
12
Mounting the LCD Monitor on a wall
•
•
•
Check the Westinghouse Digital website for wall mounting solutions.
Use the 75mm VESA hole pattern to secure a mounting plate to the LCD monitor.
Use professional installation to reduce the risk of injury and damage.
Additional Questions
•
•
See our website at www.westinghousedigital.com
Contact Westinghouse Digital Customer Service at (866) 287-5555 or write us at
service@westinghousedigital.com
13
SE-UM-1502-0501