EverFocus EZN3160 Plus User`s manual

EZN Plus Series
IR Bullet Camera
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: August, 2012
Copyright  2012 EverFocus Electronics Corp.
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by
any means without written permission of the EverFocus Electronics Corporation.
EverFocus
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 2380
www.everfocus.com.tw
August, 2012
Regulatory Notices
About this document
All the safety and operating instructions should be read and followed before the unit is operated. This
manual should be retained for future reference. The information in this manual was current when
published. The manufacturer reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.
FCC Notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved by EverFocus or
parties authorized by EverFocus could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
EverFocus Electronics Corp.
12F, No. 79, Sec. 1, Shin-Tai Wu Rd., Hsi-Chi,
Taipei Hsien, Taiwan, R.O.C.
EZN Plus Series cameras comply with CE and FCC.
i
Safety Notice
-These limits are designed to provide reasonable protection. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: -Reorient or
relocate the receiving antenna.
-Increase these separations between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
To reduce risk of fire or electric shock, do not expose this appliance to rain or moisture.
Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or
covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.
Handle the appliance with care. Do not strike or shake, as this may damage the appliance.
Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to
clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe
gently.
Do not operate the appliance beyond its specified temperature, humidity or power source ratings.
The input power source for this appliance is DC 12V & PoE. Do not use the appliance in an extreme
environment where high temperature or high humidity exists. Use the appliance at a temperature
between -40°C ~ 55°C / -40°F ~ 131°F (DC 12V); -20°C ~ 55°C / -4°F ~ 131°F (PoE) and humidity between
20% ~ 80%.
ii
Use only the recommended power supplies. Power supplies must comply with the requirement of
the latest version of IEC60950-1. Substitutions may damage the unit or cause a fire or shock hazard.
Electrostatic-sensitive device. Use proper CMOS/MOSFET handing precautions to avoid
electrostatic discharge.
Installation should be performed by qualified service personnel only in accordance with the
National Electrical Code or applicable local codes.
Terms and Trademark
Ethernet, Internet Explorer, Linux, Microsoft, Windows, WWW are registered trademarks of the
respective holders. Other product names appearing in this User's Guide may be trademarks or registered
trademarks of their respective holders. Java™ and all Java-related logos and trademarks are trademarks
or registered trademarks of Sun Microsystems, Inc. in the United States and other countries.
Support
If the unit ever needs to be repaired or serviced, the customer should contact the nearest EverFocus
Electronics Corp. Service Center for return authorization and shipping instructions.
iii
TABLE OF CONTENTS
1.
Introduction ............................................................................................................... 1
2.
Features ..................................................................................................................... 2
3.
Overview .................................................................................................................... 3
4.
Installation ................................................................................................................. 4
4.1
Packing List ....................................................................................................................................... 4
4.2
4-Pin Data Cable ............................................................................................................................... 4
4.3 Basic Installation .............................................................................................................................. 5
4.3.1 Mounting and Wiring ........................................................................................................................................ 5
4.3.2 Inserting a Micro SD Card .................................................................................................................................. 7
4.3.3 Adjusting Camera Focus / Zoom........................................................................................................................ 8
5.
Accessing the User Interface ...................................................................................... 9
5.1 Assigning an IP Address ................................................................................................................... 9
5.2 Connecting the Camera to the Network ........................................................................................ 11
5.3 Live View Window.......................................................................................................................... 13
6.
Playback ................................................................................................................... 17
6.1 Assigning an IP Address ................................................................................................................. 17
6.2 Setting Up the Playback Function .................................................................................................. 19
6.2.1 Preparing the Micro SD Card ........................................................................................................................... 19
6.2.2 Testing the Playback Function ......................................................................................................................... 20
6.3
7.
Playing Back Using ARV Viewer ..................................................................................................... 21
Settings .................................................................................................................... 22
7.1 System Info .................................................................................................................................... 22
7.1.1 Information...................................................................................................................................................... 22
7.1.2 Log ................................................................................................................................................................... 23
7.2
User Config ..................................................................................................................................... 24
7.2.1 Live View Config .............................................................................................................................................. 24
7.2.2 Recording / Snapshot ...................................................................................................................................... 25
7.2.3 Language ......................................................................................................................................................... 26
7.3 Network ......................................................................................................................................... 27
7.3.1 Network ........................................................................................................................................................... 27
iv
7.3.2 DDNS................................................................................................................................................................ 29
7.3.3 SMTP / FTP ...................................................................................................................................................... 31
7.3.4 HTTPS............................................................................................................................................................... 33
7.3.5 SNMP ............................................................................................................................................................... 36
7.3.6 Network Alarm ................................................................................................................................................ 36
7.4
Video .............................................................................................................................................. 37
7.4.1 Multi Streaming ............................................................................................................................................... 37
7.4.2 Camera ............................................................................................................................................................ 39
7.4.3 Advanced ......................................................................................................................................................... 41
7.4.4 ROI (Region of Interest) ................................................................................................................................... 47
7.4.5 Privacy Mask .................................................................................................................................................... 48
7.5 Audio .............................................................................................................................................. 50
7.6
User ................................................................................................................................................ 51
7.6.1 User Information ............................................................................................................................................. 51
7.6.2 IP Address Filter ............................................................................................................................................... 53
7.7 Event .............................................................................................................................................. 54
7.7.1 Event Settings .................................................................................................................................................. 54
7.7.2 Motion Detection ............................................................................................................................................ 57
7.7.3 Tamper Detection............................................................................................................................................ 58
7.7.4 Alarm I/O ......................................................................................................................................................... 58
7.7.5 Schedule .......................................................................................................................................................... 59
7.8 System ............................................................................................................................................ 60
7.8.1 Date/Time ........................................................................................................................................................ 60
7.8.2 Daylight Saving ................................................................................................................................................ 61
7.8.3 SD Card ............................................................................................................................................................ 61
7.8.4 Maintenance ................................................................................................................................................... 62
8.
Upgrading Firmware Using IP Utility ......................................................................... 64
9.
Specifications ........................................................................................................... 66
v
EZN Plus Series
1.
Introduction
The EZN Plus series is an outdoor bullet camera delivering image quality of up to 3-megapixel. The camera
supports both H.264 and MJPEG compression formats. The IP66-rating and vandal proof housing make it
suitable for outdoor use. The IR LEDs are also implemented for infrared illumination in night vision
applications.
The EZN Plus series features the Wide Dynamic Range (WDR) function, which can provide clear images
even under back light circumstances where intensity of illumination can vary excessively. A built-in micro
SDHC card slot and Power over Ethernet (IEEE802.3af) features are also provided. You can power the
camera over the network or by connecting the camera to a 12V DC power supply. Since the EZN Plus series
conforms to ONVIF / PSIA for compatibility with other network video devices, it interoperates with a wide
variety of hardware and software systems.
The EZN Plus Series Models
Model Name
Megapixel
P-Iris
WDR
EZN3160 Plus
1.3 MP
Yes
Yes
EZN3260 Plus
2 MP
Yes
Yes
EZN3340 Plus
3 MP
Yes
No
System Requirement
Before installing, please check that your computer meets this system requirement.
•
Microsoft Internet Explorer 7 or above
1
EZN Plus Series
2.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Features
1/3” Panasonic CMOS sensor (for EZN3160 Plus / 3260 Plus)
1/2.8” Sony CMOS sensor (for EZN3340 Plus)
Triple streams (stream 1 / 2 / 3 from H.264 or MJPEG)
Up to 15 fps at 2048 x 1536 (only for EZN3340 Plus)
Built-in micro SD / SDHC card slot
Removable IR-cut filter for Day / Night function
3-axis mechanism (pan / tilt / rotate)
One alarm input and output
Two-way audio
TV-out
Wide Dynamic Range (for EZN3160 Plus / 3260 Plus)
Digital Slow Shutter (DSS)
2D / 3D Dynamic Noise Reduction (DNR)
Motion Detection
10x Digital Zoom
Privacy Mask
DC 12V / PoE
2
3.
EZN Plus Series Overview No. Name Description Connects to a handheld test monitor for adjusting camera focus and 1 TV‐Out Connector 2 Focus / Zoom Control Press this control to the left or right to adjust camera focus. To zoom in / out the camera view, press this control up or down. 3 Reset Button Resets all configurations to the factory default settings. 4 Lens Varifocal lens. 5 Micro SD / SDHC Slot For inserting a micro SD / SDHC card. 6 IR LEDs 44 IR LEDs for infrared illumination in night vision applications. 7 Light Sensor Detects lights. 8 Camera Cover Remove the cover for adjusting camera focus and zoom / inserting a micro SD card or connecting to a handheld test monitor. 9 Sunshield Protect the camera from the direct rays of the sun. zoom. 3 4.
EZN Plus Series Installation 4.1
Packing List Please check that there is no missing item in the package before installing. 



EZN Plus Series Camera x 1  4‐Pin Terminal Block x 1 Quick Mounting Ring x 1  Software CD x 1 RJ‐45 Connector x 1  Quick Installation Guide x 1 Mounting Kit x 1 ‐ Long Screw x 4 (for attaching the Quick Mounting Ring to the mounting surface) ‐ Short Screw x 4 (for connecting the camera base to the quick Mount Ring) ‐ Screw Anchor x 4 (in conjunction with Long Screw) ‐ Hexagon Key x 1 (for adjusting the camera position) ‐ Hexagon Wrench x 1 (for removing the sunshield) ‐ Torx Wrench x 1 (for removing the lock tab) ‐ Mounting Template x 1 Note: Contact the shipper if any items appear to have been damaged in the shipping process. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service Branch. Please also keep the shipping carton for possible future use. 4.2
4‐Pin Data Cable The 4‐Pin Data Cable provides connections for power, audio input / output and alarm input / output. The wires are illustrated and defined below. Pin Assignment for Alarm Input / Output Pin 1: Alarm GND Pin 2: Alarm In Pin3: Alarm Out‐ Pin4: Alarm Out+ 4 4.3
EZN Plus Series Basic Installation This section will introduce the basic installation on mounting / wiring the camera, inserting a micro SD card and adjusting camera focus / zoom. 4.3.1 Mounting and Wiring Follow the steps below for mounting and wiring the camera. 1. Before screwing the camera to the wall, drill four holes on the wall according to the hole‐positions on the supplied Quick‐Mounting Ring. If you wish to run the wires into the wall, drill another hole in the middle of the circular area within the Quick‐Mounting Ring. 2. Push the four supplied anchors into the four holes on the wall. 3.
Place the Quick‐Mounting Ring against the anchoring surface so that the holes line up. Screw the Quick‐Mounting Ring to the wall using the supplied Long Screws. 4.
Screw the camera body to the Quick‐Mounting Ring using the supplied four Short Screws. a. If you want to wire the cables from the side of the camera base: 5 EZN Plus Series b. If you want to wire the cables through the wall, feed the cables through the wall and then screw the camera base to the Quick‐Mounting Ring. 5.
6.
7.
8.
Connect the network, power and other cables of the camera to the related devices. Please refer to 4.2 4‐Pin Data Cable. Optionally insert a micro SD / SDHC card into the card slot. Please refer to 4.3.2 Inserting a Micro SD Card. Access the camera live view. Please see 5. Assigning an IP Address. Or connect a handheld test monitor to the TV‐out connector on the camera module for setting image zoom and focus. Please refer to 4.3.3 Adjusting Camera Focus / Zoom. Adjust the camera angles. Pan Adjustment: Twist the Base Disk forcefully until it unscrews from the Lock Ring. Rotate the camera 360° to the desired position and then screw the Lock Ring until it locks against the Base Disk. Tilt Adjustment: Loosen the Tilt Screw using the provided hexagon key and adjust the tilt angle 90°. Rotational Adjustment: Loosen the Rotate Screws on both side of the camera body using the providing hexagon key and rotate the camera 360° (180° to the left / 180° to the right). 6 EZN Plus Series 4.3.2 Inserting a Micro SD Card You can optionally insert a micro SD card into the card slot on the camera module for recording videos. 1. Remove the Sunshield from the camera. Loosen the screw on the Sunshield using the provided hexagon wrench. Slide the Sunshield out from the rail on the camera body. 2. Unscrew the Fix Screw using the provided torx wrench and then remove the Lock Tab. 3. Rotate and then remove the camera cover. 4. Insert a micro SD card into the card slot. 5. Slide the Sunshield back to the camera body. Note: When properly installed, the rear‐side of the Sunshield should be even with the rear‐side of the camera body. Extending the Sunshield in order to shade the lens will compromise the image quality. 7 EZN Plus Series 4.3.3 Adjusting Camera Focus / Zoom After wiring the cables, you can adjust the camera focus and zoom for better image quality. 1.
2.
3.
4.
Follow Steps 1 ~ 3 in 4.3.2 Inserting a Micro SD Card to remove the camera cover. Connect the power cable of the camera to the power source. Connect a handheld test monitor to the TV‐out connector for setting image zoom and focus. To adjust camera focus, push the Focus / Zoom Control to the left or right. To zoom in / out the camera, push the Focus / Zoom Control up or down. 5. Slide the Sunshield back to the camera body. Note: When properly installed, the rear‐side of the Sunshield should be even with the rear‐side of the camera body. Extending the Sunshield in order to shade the lens will compromise the image quality. 8 EZN Plus Series
5.
Accessing the User Interface
This section explains how to access the Web interface of the camera for configuration.
5.1
Assigning an IP Address
You have to assign an IP address for your camera to be accessible. To assign an IP address to the camera,
use the IP Utility (IPU) software included in the software CD. Please connect the IP camera in the same
LAN of your computer.
1.
Install and then start the IPU program
. The following dialog box appears.
2.
3.
Click Find Devices to search the cameras connected in the LAN. The default network values of
the cameras will be displayed. By default, the network protocol of the camera is DHCP.
To configure the network settings, select a camera and then click Login/Multi Login to log in.
4.
Type the user ID and password. Click OK.
Note:
1. The default user ID is user1 and the default password is 11111111.
2. If you select more than one camera that has the same user ID / password, you will be able
to log in several cameras at once.
9
EZN Plus Series
5.
To change the IP address, double-click the IP Address of the camera. Type a new IP address and
then click Set IP Address to save the settings.
You can also change the other settings by double-clicking the values. After configuring the values,
click Save Configuration.
Note: Most networks support DHCP protocol, but if you are unsure of your network protocol,
please consult your IP administrator for network configuration details.
6.
7.
To access the camera, highlight the camera and click Connect to Selected IP. The Internet
Explorer window pops up.
Type the user ID and password to log in. The Live View window of the camera appears.
Note: You might be required to download ActiveX, which is required to view the camera feed.
If asked, click "Yes".
10
EZN Plus Series
5.2
Connecting the Camera to the Network
There are three methods to connect the IP camera to the network: Router or LAN Connection, Direct
High-Speed Connection and One-to-One Connection.
Router or LAN connection
This is the most common connection in which the IP camera is connected to a router and allows
multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The camera must be
assigned an IP address that is compatible with its LAN. By setting up port forwarding on the router, you
can remotely access the cameras from outside of the LAN via the Internet. To remotely access the Web
interface of the IP camera, please refer to 7.3.2 DDNS. To set up port forwarding, please consult the
manual of the router.
Straight-through LAN patch cable
Right: Pinout of a straight-through cable.
11
EZN Plus Series
Direct High-Speed Connection
In a Direct High-Speed Connection, the camera connects directly to a modem without the need for a
router. You need to set the static or dynamic WAN IP address assigned by your ISP (Internet Service
Provider) in the camera’s configuration web pages. To access the camera, just type “http://xxx”, where
xxx is the IP address given by your ISP. If you have a dynamic IP address, this connection may require
that you use DDNS for a reliable connection. Please refer to 7.3.2 DDNS.
One-to-One Connection (Directly from PC to IP Camera)
You can connect directly without using a switch, router or modem. However, only the PC connected to
the camera will be able to view the IP camera. You will also have to manually assign a compatible IP
address to both the computer and the IP camera. Unless the PC has another network connection, the IP
camera will be the only network device visible to the PC. See the diagram below:
Pinout of straight patch cable
Right: Pinout of a crossed-over cable.
12
EZN Plus Series
5.3
1.
Live View Window
Press the
button to display the "Live View" window. Double-click on the
image to show a full-screen display, double-click again or press ESC to return to the normal display.
If you experience video feed lag time (if connected via Internet), you can reduce the resolution or
limit the number of streams. See 7.4.1 Multi Streaming.
2.
Press the
button to play the recorded data directly from the on-camera Micro
SD / SDHC card (for this function to become active, you have to insert a Micro SD / SDHC card in the
Micro SD / SDHC card slot on the rear panel of the camera. See 7.8.3 SD Card).
13
EZN Plus Series
3.
Press the
button to enter the Settings page. On the Settings page, there are
8 submenu sections: [System Info], [User Config], [Network], [Video], [Audio], [User], [Event] and
[System]. Click on the section buttons to open their configuration fields. See the Settings section
below for more information.
4.
Press the
button to exit the system and close this browser page.
5.
Video Stream
Select the Video Stream (Stream 1, Stream 2 or Stream 3) that will be displayed in the video box on
the right. Stream 2 and Stream 3 are only selectable if you have enabled the stream. The default
setting is Stream 1 only. See 7.4.1 Multi Streaming.
6.
View Size
Use this to select the appropriate view size and shape of the video box on the right. A smaller size
might increase transmission speed and video quality.
7.
Digital Zoom
Click the Zoom In / Zoom Out buttons or roll the mouse wheel to zoom in / out the camera live view
up to 10x. Clicking on a magnified image will re-center the image around that point.
8.
One Push
This function is only available for EZN3160 Plus / 3260 Plus. The One Push button can be displayed
on the live view window by enabling the Show One Push Buttons function on the User Config < Live
View Config Setting page (see 7.2.1 Live View Config). To enable the button (turned from faded to
clear), on the Video < Advanced Setting page, select One Push from the White Balance Settings
Mode drop-down list, and click the Apply button. Once this is done, pressing the One Push button
on the Live View Window will instruct the camera to adjust the white balance settings, and these
settings will be active until the button is pushed again. This is like a “semi-automatic” way to adjust
white balance to suit the user, if the Auto or Manual mode does not give the result the user wants.
9.
Record
The Record button is used to record the current video stream. Click the Record button to start /
stop recording. This icon is only for one-minute video recording. To record long-period recordings,
please set a recording schedule (See 7.7.5 Schedule). The location on your computer, where the
image files will be saved to, and file size can be specified in the submenu (see 7.2 User Config).
14
EZN Plus Series
10. Snapshot
Click the Snapshot button to save a snapshot of the video image currently being displayed. The
location on your computer where the snapshot data will be saved can be specified in “Settings >
User Config” (see 7.2 User Config).
11. Play Audio / Transmit Audio
Click the “Play Audio” (speaker) and “Transmit Audio” (microphone) buttons to switch the sound
on/off for the speaker and microphone, respectively (if such external devices have been connected
to the camera directly or via the network).
12. Manual Control
– Trigger Event
Press the “Trigger Event” button to trigger an event directly from the Live View window. If you have
configured an event (in the Event submenu) that will trigger a reaction (like a recording) when a
Manual Trigger event occurs, clicking this button will trigger that reaction. You can select what that
reaction will be. You can, for instance, set the camera to record the audio/video feed to the SD card
on board the camera. You can then click on the Playback button to open the Playback page and
search for and play all such recordings that had been stored on the card. Such event actions will be
effective once they have been configured in the “Event” menu (see 7.7 Event).
– Reset Alarm
Press the “Reset Alarm” button to reset the alarm output remotely.
13. Lens Control
These buttons control the lens actions. Click the
icon to focus closer quickly. Click the
icon to focus closer slowly. Click the
icons to focus farther quickly or slowly. Click the
icons to zoom in quickly or slowly. Click the
icons to zoom out quickly or slowly.
14. Status Display (info line that can be placed above video box or at bottom of page)
This shows the name of the camera that is currently active or being configured, current date/time
and current frame rate. You can activate these info displays in the Settings > User Config page (see
7.2 User Config).
15
EZN Plus Series
15. Event signal icons (above video screen)
When an alarm or motion event is triggered, a signal icon will appear at the top right of the Live
View window to alert the user.
Alarm event icon
: When an alarm is triggered, this icon appears.
Motion detection icons
: The colors of these motion event icons correspond to the
colors of the motion trigger areas you have configured in the Motion Detection submenu (see 7.7.2
Motion Detection).
Recording icon
: When the camera is recording to a PC-based folder, this icon appears.
16
EZN Plus Series
6.
Playback
You can remotely play back the recordings stored in the on-camera micro SD card on the Web interface, or
play back the recordings stored in the computer using the ARV Viewer included in the software CD.
Playback is designed as a quick way to check recent recordings that were triggered by Events that were
configured to “Record to SD Card” in the Settings > Event > Event Settings page (see 7.7.1 Event Settings).
Note: Note that the Playback page is only accessible once the on-camera SD card is inserted and active.
6.1
Assigning an IP Address
On the Live View Window, click the Playback button
17
to open the Playback page.
EZN Plus Series
Search by File: Click the Search button to search for all recording files on the on-camera SD card.
Search results will be displayed in the Filename area.
Search by Time: Click the calendar icon and select the date and time from which you want to search
until the present moment. Click search to get your search results, which will be displayed in the
Filename area.
Search by event: Click the type of Event recordings you want to search for (Alarm, Motion, Manual
Trigger) and then click the calendar icons to select the Start Time date/time and the End Time
date/time of your search. Click Search to get your search results, which will be displayed in the
Filename area.
Multiple Files: Check this box if you want the video player to play all the files in the selected folder.
The files will be displayed in the Filename area.
Loop Again: Check this box if you want the video player to play the selected file over and over again.
Play: Once you have opened the file’s folder and have clicked on the file to highlight it, its details will
be displayed in the File Information area. You can now click Play to play that specific file.
Pause: Click this button to pause the playback.
Stop: Click this button to stop the playback.
【Recording List】
Filename: This area will display a list of search results (recording files and folders). Folders (named
with the recorded date) will be displayed first. Click on the folder and click on each subfolder until
the recording files (.arv) in that folder is listed.
File Information: Click a file on the Filename list, the selected file information will be listed.
Copy: Click this button to copy the selected file to the computer-based folder of your choice. A
browsing box will open so that you can search for the folder of your choice. You can use the ARV
Viewer to play back the recordings recorded in your computer. For details on ARV Viewer, see 6.3
Playing Back Using ARV Viewer.
Lock: Click this button to lock the selected file. This will protect that file from being overwritten
during any overwrite procedure. The file will thus be saved on the micro SD card indefinitely.
However, the file will still be deleted if the micro SD card is ever formatted.
Remove: Click this button to delete the selected file.
18
6.2
EZN Plus Series Setting Up the Playback Function Note that the Playback function will not be active until the user has inserted a micro SD card in the camera’s micro SD card slot. The card may also have to be formatted in the Settings submenu. 6.2.1 Preparing the Micro SD Card Once you insert a functional Micro SD card into the slot, the Playback button on the Live page should become active within seconds (see section 6.2.2 below – the grey letters should turn white). IF NOT, do the following: 1. From the Live page, click Settings > System > SD Card. If no card has been inserted yet, the Remove button should be faded, indicating that no card is being detected. (If a card is inserted, and the Remove button is still faded, pull the card out and re‐insert it.) 2. Slide the card into the slot until it clicks into position. 3. The Remove button should become active within a few seconds, indicating the card is active. 4. If the Remove button stays faded, click the Format button to format the card. NOTE: All data on the disk will be deleted if the Format button is clicked. 19 EZN Plus Series
6.2.2 Testing the Playback Function
1. Once the micro SD card is detected by the system, the button
turn to
(inactive) will
(active).
2. To test the Playback function (this is not required), set up a “Manual Trigger” Recording Event by
clicking Settings > Event > Event Settings.
3. Click the “Add” button on the middle right side of the page to open an “Add Event” box.
4. Give the event a name, like “Test 1”.
5. In the “Event Triggered by” field, click on Manual Trigger.
6. Below this, check “Enable This Event”, “Enable Post-trigger Buffer”, and “Record to SD Card”.
7. To save your settings, click OK, or close the box by clicking on the red x icon at top right of the box
(in which case you will be asked if you want to save the data, to which you should reply OK). The
box will close and the new event will be listed in the list area of the Event Settings page.
8. Look at the “Post-trigger Buffer” at the bottom to make sure the buffer time is set to 10 seconds.
9. Click “Apply” to make sure all settings are saved.
10. Click the Live button to go back to the Live page.
11. Get ready to click the Trigger Event button at the bottom of the page. Before you do, see if you can
find something in the view screen that will give you a visual time marker. For instance, if you can
get your hand in front of the camera’s lens, get ready to count down on your fingers.
12. Click the Trigger Event button and slowly count down on your fingers in front of the lens (if you are
able to do so – if not, try to find visual cues on the view screen that will help you to mark the
moment you pushed the trigger). The recording period will be as long as the buffer time you
selected – the default period is 10 seconds.
13. Click the Playback button to open the Playback page.
14. There are different ways to search for recording files on the camera’s micro SD card (i.e. the
Playback memory). For a recent recording like your test event, simply click the “Search” button
under the “Search by File” header.
15. If the micro SD card is active and formatted correctly, the recording folder’s name (the recording
day’s date) will appear in the Filename box at the bottom. Click on this folder to open it. If there are
sub-folders, click on the bottom one (the most recent would be at the bottom) until you can click
on a file that cannot open to another sub-level and shows data in the File Information box to the
right. This would be the file of the most recent recording event.
16. To play this file, click the Play button below the video box. The test footage you have recorded
should start playing. Play time should be 10 seconds if you left the Post-trigger Buffer as 10
seconds.
20
6.3
EZN Plus Series Playing Back Using ARV Viewer You can play back the recordings stored in the computer using the ARV Viewer included in the software CD. To store the recordings in the computer, please refer to Recording List > Copy in 6.1 Remote Playback using Playback Page. No. Item Name Descriptions 1 Snapshot Click to take and save a snapshot. 2 Load File Click to load the recordings for playing back. 3 Convert ARV to AVI Convert the recording from ARV format to AVI format. 4 Playback Time Display the playback time. 5 Total Time of Recording Display the total time of the recording. 6 Stop Click to stop playing the recording. 7 Step Reverse Click to display the previous frame. 8 Play Click to play back the recording. 9 Pause Click to pause the recording. 10 Step Forward Click to display the next frame. 21 EZN Plus Series
7.
Settings
Click the Settings button on the Live View Window to enter the settings submenu. There are nine buttons
on the left-side of the submenu: Live, System Info, User Config, Network, Video, Audio, User, Event and
System. Click the Live button can go back to the Live View Window.
7.1
System Info
The System Information and System Log can be checked on this page. Click the top tab of the one you
want to see.
7.1.1
Information
Click the Information tab, the following dialog box appears. These values cannot be changed on this
page, and are for reference only.
22
EZN Plus Series
7.1.2
Log
Click the Log tab, the following dialog box appears. The sequence number, date, time and event
messages of the log event will be displayed in the System Log field. The log will display the last 256 log
events. Click the Export button to export the system log event list into a “.txt” file and select the
location where the exported log file will be saved to.
23
EZN Plus Series
7.2
User Config
Each user can set a different configuration for his/her Live page here. These settings will be applied to
the logged-in user’s Live page every time he/she logs in.
7.2.1
Live View Config
【Video/Audio Connection Protocol Setting】If needed, select the protocol that applies to your
connection setup. Click Apply to apply the changes or Reset to reset without saving the changes.
【Text Settings】Check the box of each option (Machine name, Date/Time, Frame Rate) to display this
info on the Live View Page.
Foreground Color: Slide the Red, Green and Blue bars to create your preferred text color for the info
text line.
Position: Select the position where the text will be displayed. Choose from Upper Left / Lower Right /
Lower Left.
Click Apply to apply the changes or Reset to reset without saving the changes.
【Date/Time Format Used in Text】Click the dropdown menu to select date/time format from the
listed options. Click on the desired hour format. Click Apply to apply the setting changes or Reset to
reset without saving the change.
【Live View Layout Settings】 Check the Show One Push Buttons or the Show Lens Control Buttons
boxes if you want to show these buttons on the Live View Page. Uncheck these boxes to hide these
buttons. This function is only available for EZN3160 Plus / 3260 Plus.
24
EZN Plus Series
7.2.2
Recording / Snapshot
This configures where your Record Button and Snapshot Button (
) files will be saved if you
click one of these buttons. Selectable folders will be on the computer only, not on the on-camera SD
card.
【Video/Audio Connection Protocol Setting】If needed, select the protocol that applies to your
connection setup. Click Apply to apply the changes or Reset to reset without saving the changes.
【Recording / Snapshot Export Settings】
Enable Event Recording to PC: Checking this box will let the system save Record/Snapshot Button
recordings to the folder configured below on the user’s PC.
Export Folder: Select the Export folder for the action above by clicking on the browse (…) button, and
then select the desired folder.
File size: The user can limit the size of each recorded file here (in minutes). When a single recording
file exceeds the time you set, the system will create a new file to save that data to.
Overwrite: Select “ON” for overwriting recording/snapshot file when the disk storage capacity is full.
The user can set the storage capacity limitation in the in-sentence field in the gray box below the
Overwrite setting: “If the remaining hard disk capacity is less than ____ MB (50~2000), system will
stop recording or start overwriting. “
Click Apply to apply the setting changes or Reset to reset without saving the changes.
25
EZN Plus Series
7.2.3
Language
Select the language to be displayed on the Web interface of the IP camera. The default language is
English.
To add a new language not listed in the current Language list, click the Browse button to locate the
new language file (.evb) on your computer and then click the Upload button. Updated language files
might be available on the manufacturer’s website. Contact your vendor if required.
Click Apply to apply any changes or Reset to reset without saving the changes.
Note: Uploading a new language file will cause the system to reboot automatically. Please create a
new network connection to the IP camera when the reboot is complete.
26
EZN Plus Series
7.3
Network
This page covers network-related settings, including Network, DDNS, SMTP/FTP, HTTPS, SNMP, and
Network Alarm.
7.3.1
Network
The following information is required to configure the network settings. Contact your network
administrator or your internet service provider to get the info.
【IP Settings】
IP Type: Refer to the network administrator for these settings of the server. Default: DHCP



DHCP: This setting lets the system use an automatically assigned (dynamic) IP address. This address
can change under certain circumstances. For instance, when the camera’s network switch/hub has
to be rebooted. Do not assign to the DHCP server the same IP addresses used for the other network
cameras and PCs with unique IP addresses.
Static IP: The user can manually set the Static IP address. This type of address is stable and cannot
change, but the user has to make sure there are no address conflicts with other network-connected
devices.
PPPoE: This is a DSL-connection application. The ISP will ask the user to input a username and
password. Contact your ISP for these details.
27
EZN Plus Series
Note: If PPPoE is selected as the IP type, the supplied IP Utility program will not be able to
detect the device.
IP address: When DHCP is not used, the user needs to manually enter the IP address of the camera. Do
not enter an IP address that is already used for your computer or other network cameras.
Subnet Mask: This field is used to set the subnet mask for your network, so that the IP camera will be
recognized within the network. Example: 255.255.255.0. When DHCP is selected, the DHCP server will
assign this value automatically.
Gateway: This field is used to set the gateway for your network so that the IP camera will be
recognized within the network. When DHCP is selected, the DHCP server will assign this value
automatically.
Primary DNS: Enter the IP address of the DNS server if this is provided by an ISP.
Secondary DNS: If your ISP provided you with a secondary DNS address, please enter it here.
Username: Enter the account’s username (used only for PPPoE).
Password: Used only for PPPoE.
IPv6: Enter the IPv6 details in this area, if this applies to your system.
Click Apply to apply the setting changes or Reset to reset without saving the change.
【Port Settings】Enter the HTTP, HTTPS and RTSP port numbers and click Apply to save.
【Multicast Settings】Enable if required, fill in the setting options and click Apply to save.
28
EZN Plus Series
7.3.2
DDNS
DDNS (Dynamic Domain Name System) is a service used to map a domain name to the dynamic IP
address of a network device. You can set up the DDNS service for remote access to the IP camera.
DDNS assigns a domain name (URL) to the IP camera, so that the user does not need to go through the
trouble of checking if the IP address assigned by DHCP Server has changed. Once the IP is changed, the
IP camera will automatically update the information to the DDNS to ensure it is always available for
remote access.
Before enabling the following DDNS function, user should have applied for a host name from the DDS
service provider’s website. We support these four DDNS server providers:
www.everfocusddns.com, www.sitelutions.com, www.dyndns.com, and www.no-ip.com
Note: We highly recommend that you use xxxx.everfocusddns.com for the simplicity of setting up
your IP cameras.
【DDNS Settings】
Enable: Check this box to enable the DDNS function.
Service ISP: You can either apply for a host name from EverFocus or other DDNS server providers.
If you choose the EverFocus DDNS server, you can obtain a free host name from EverFocus by following
the steps below:
• From EverFocus: To obtain a free host name from EverFocus, type a desired host name in the
textbox, click the Register / Update button, and then click the Apply button.
• From other DDNS server providers: To obtain a domain name from one of the three DDNS server
providers, you have to register your name with the provider first, and then select the provider and
fill in the required information. Please refer to the specific DDNS company’s website for further
information.
Click Apply to apply the setting changes or Reset to reset without saving the changes.
29
EZN Plus Series
Note:
1. In order to support the full functionality of the camera, you must open the port numbers (80,
554, 443) on the router for remote access to the IP camera. This function is available on most
routers in the market and is often known as “Port Forwarding”. To set up Port Forwarding,
please consult the manual of the router.
2. In certain router models, it is possible that you will not be able to access the camera using
DDNS while inside the router’s network. Please try using a PC located outside of your router’s
network.
Default Ports on All EverFocus IP Cameras:
HTTP: 80
RTSP: 554
HTTPS: 443
30
EZN Plus Series
7.3.3
SMTP / FTP
【Set SMTP Server (email)】This area is for configuring the mail server that is used to send e-mail
notifications from the camera to predefined addresses via SMTP. Note that to enable e-mail
notification function, you have to check the Send Mail Notification item on the Event dialog box
(see 7.7.1 Event).
SMTP Server: Enter the IP address or the host name of the SMTP server used to send e-mails.
SMTP Port: Enter the port number for SMTP. The default is 25.
Authentication: Check this box if the SMTP server requires authentication (user/password).
User name: Input the user’s login ID if the SMTP server requires authentication.
Password: Input the user’s login password if the SMTP server requires authentication.
31
EZN Plus Series
Receiver Address: Input the e-mail addresses for receiving an e-mail message when an EVENT is
enabled and triggered. Please use “;” to separate multiple addresses.
Sender Address: Input the sender’s e-mail address, so that the receiver can recognize the sender
when an Event message is received.
Attach Image: Check this box if you want to attach an image when an alarm is triggered or an IP
camera detects events.
Send Test Email: Click the Test button to send a testing email to the assigned address.
Click Apply to apply the setting changes or Reset to reset without saving the changes.
【Set FTP Server】The settings relating to the FTP server used to transmit the alarm images can be
configured here. Note that to enable uploading images to the FTP server function, you have to
check the Upload to FTP item on the Event dialog box (see 7.7.1 Event).
FTP Server: Enter the IP address or the host name of the FTP server.
FTP Port: Enter the port number for the FTP server. Default is 21.
Recording Path: Assign the recording path.
User Name: Set FTP User’s name.
Password: Set FTP password.
PASV mode: Check to enable Passive mode. Passive mode is normally enabled. If a connection
cannot be established, uncheck "PASV Mode”.
Test FTP Server: Click the Test button to send a testing file to the assigned FTP server.
Click Apply to apply the setting changes or Reset to reset without saving the changes.
32
EZN Plus Series
7.3.4
HTTPS
Hypertext Transfer Protocol Secure (HTTPS) is a combination of the Hypertext Transfer Protocol and
the SSL/TLS protocol and provides encrypted communication and secure identification of a network
web server.
【Create Certificate】To use HTTPS, a Certificate must be created first. There are two ways to create
and install a certificate:

Create Self-signed Certificate: A self-signed certificate can be used until a Certificate
Authority-issued certificate has been obtained. Click the Create Self-signed Certificate button
to install a self-signed certificate. Although self-signed certificates are free and offer some
protection, true security is only implemented after the installation of a signed certificate issued
by a certificate authority. Enter the required Certificate information as shown below. This info
will be displayed on the certificate if anyone wants to inspect it. Enter all required information
and click Apply to save it.
33
EZN Plus Series

Create Certificate Request: An official certificate can be requested from an issuing Certificate
Authority by clicking the Create Certificate Request button. Enter all the required info and
click Apply to save and send the request.
【Created Request】This field will show the Subject field of the created request (see below). The
properties of any current certificate request can be viewed by clicking the Property button in this
field. To create and install another certificate or request, remove the existing one by clicking the
Remove button to erase the certificate or request.
【Install Signed Certificate】When the signed certificate is sent back to you from the Issuing
Authority, download it on your computer. Then click the Browse button in this field to search for
the file. Click on the file and press the Upload button to import the certificate.
【Installed Certificate Information】Once a certificate has been uploaded, this field will show the
subject line of the certificate (see the example below).
34
EZN Plus Series
Press the Property button to view the details of the certificate. A pop-up window will appear with
the information (below is an example of the Property pop-up window of a self-signed certificate).
To create and install other certificates, remove the existing one by clicking the Remove button to
erase the certificate.
35
EZN Plus Series
7.3.5
SNMP
The default values for SNMP v1/v2/v2c and SNMP v3 are already filled in. Click either of the Enable
buttons to enable either of the two. Make your changes as desired. Click on the Trap Address field to
enter the digits, if required.
7.3.6
Network Alarm
This function works with EverFocus’s CMS software, e.g. the PowerCon or the Power Video Plus. For
the setting details, please refer to the CMS network alarm protocol.
36
EZN Plus Series
7.4
Video
The settings relating to video such as streaming, camera OSD can be configured on this page. The
"Video" page has five tabs: Multi-streaming, Camera, Advanced, ROI and Privacy Mask.
7.4.1
Multi Streaming
【Installed Certificate Information】This IP camera can output three video streams simultaneously.
For each of these streams, the user can set the compression format, resolution, bit rate, and frame
rate individually. Stream 1 is always enabled for live view. To enable Stream 2 and/or Stream 3,
check the “Enable” box the header of each stream.
Note: If you connect to the camera via the Internet and experience a delay (lag time) in the
video feed, try to reduce the number of streams and the quality and resolution of the streams –
but keep the frame rate at its maximum.
Format: Select the encoding format – H.264 or MJPEG.
Resolution: Select the most suitable resolution for your needs.
Frame Rate: Select from 1 to 30 fps.
Bit Rate: If required, select whether you want the stream to stream a Constant Bit Rate or a
Variable Bit Rate, and set the values of whichever option you choose.
Click Apply to apply the setting changes or Reset to reset without saving the changes.
37
EZN Plus Series
【Video Recording Settings】Select the stream you want to configure and then select whether you
want the recording files of that stream to be saved in AVI or ARV format. Click Apply to apply the
setting changes or Reset to reset without saving the changes.
【Time Stamp Settings】 You can select the Date/Time format, position, and add the setting to the
streaming.
Click Apply to apply the changes, or Reset to reset without saving the changes.
38
EZN Plus Series
7.4.2
Camera
【Image Settings】 Set the Brightness, Contrast or Sharpness of the image. Click Apply to apply the
changes, or Reset to reset without saving the changes.
【Camera Settings】
Mirror: Switch Mirror ON to rotate the image horizontally around a vertical axis.
Flip: Switch Flip ON to rotate the image vertically around a horizontal axis.
AE: The options vary among models:
 ALC: Selecting Automatic Light Control allows the camera circuitry to either take bright
spots more into consideration (peak), bringing out detail in bright areas, or less into
consideration (average) bringing out detail in shadows.
 AES: Selecting Auto Electronic Shutter disables the Shutter setting below this setting. In this
mode, the camera measures the light level and decides whether it needs more or less light
and then automatically adjusts the shutter speed accordingly.
 Manual: Select this option to manually set up the Shutter (Manual) and AGC (Manual)
values.
 Auto: Select this option to apply the system settings.
BLC: Back Light Compensation (BLC) is used to make the subject appear clearer when it is set
against a bright background.
 OFF: Select to switch Back Light Compensation functions off.
 ON (BLC): The BLC can increase the exposure of a dark area surrounded by a brighter area,
HLC can decrease the exposure of bright areas surrounded by darker areas. This enables the
camera to better display information that would otherwise have been “whited out”, like a
license plate between two bright headlights on a dark road.
39
EZN Plus Series
ON (HLC): The Highlight-Suppression BLC is used to reduce the brightness of light sources in
a specific area. It is activated only in a low illumination environment to minimize the effects
of glare from bright lights such as spotlights, street lights or headlights in the field of view.
WDR: The Wide Dynamic Range (WDR) function provides clearer images when both of the very
bright and dark areas simultaneously appear on the camera view. There are four value options:
OFF, Low, Middle and High. Note that when WDR is ON, some parts of the image may appear
solarized. This is normal for WDR, and is not a camera malfunction. This function is only available
for EZN3120 Plus / 3220 Plus.

D/N Mode
 Auto: Select to let the camera automatically switch to Night mode (black and white) when
the light levels fall to a specified level, and back to Day mode (color) when the light levels
rise to a specified level.
 Day: Select to keep the camera in Day mode (color), even in nighttime.
 Night: Select to keep the camera in Night mode (black and white), even in daytime.
【Lens Control】Set the Zoom, Focus and Digital Zoom actions of your camera.
: Click and hold the button to add the value continuously
: Click and hold the button to minus the value continuously.
: Click the button to add the value one step forward
: Click the button to minus the value one step backward.
40
EZN Plus Series
7.4.3
Advanced
41
EZN Plus Series 【Camera Settings】 Exposure Settings (AE): This setting is used to adapt to the amount or type of light used by the camera. The options vary among models. Mode: This function is not available for EZN3260 Plus.  ALC: Selecting Automatic Light Control allows the camera circuitry to either take bright spots more into consideration (peak), bringing out detail in bright areas, or less into consideration (average) bringing out detail in shadows.  AES: Selecting Auto Electronic Shutter disables the Shutter setting below this setting. In this mode, the camera measures the light level and decides whether it needs more or less light and then automatically adjusts the shutter speed accordingly.  Manual: Select this option to manually set up the Shutter (Manual) and AGC (Manual) values.  Auto: Select this option to apply the system settings. IRIS: Specify the size of the Iris opening by adjusting the slide bar to the left or right. Shutter: If enabled, this setting lets you set the shutter speed yourself (measured in fractions of a second). AGC: Set the Auto Gain Control limit here. The lower the AGC level, the lower the video signal and the noise. However, the image will be darker under low‐light condition with IR‐off if you set up the Iris to the maximum level. Slow Shutter: This option can be switched on when AES Mode is selected in the Exposure Settings (AE) field. Flickerless: If the Mode field in the Exposure Settings (AE) area has been set to AES, then this option becomes available. Choose between OFF, 50HZ, 60HZ, 50HZ (High Luminance) or 60HZ (High Luminance). EV Setting: Set up the Exposure Value. Note the brightness of the screen changes when you change the EV value. AE Response: Set up the Auto Exposure Response time. This function is only available for EZN3340 Plus. AE Weighting Area: Select an AE Weighting area. Each setup AE Weighting Area is configured with the appropriate brightness level on the center and the surrounding areas. This function is only available for EZN3340 Plus. Brightness: Set the image brightness here. AE Reference: Set the Auto Exposure value here. Black Level: Set the Black level here. This function is only available for EZN3340 Plus. 42 EZN Plus Series WDR: The Wide Dynamic Range (WDR) function provides clearer images when both of the very bright and dark areas simultaneously appear on the camera view. There are four value options: OFF, Low, Middle and High. Note that when WDR is ON, some parts of the image may appear solarized. This is normal for WDR, and is not a camera malfunction. This function is only available for EZN3160 Plus / 3260 Plus. Visibility Enhancement: (OFF/Low/Middle/High) Images in foggy or rain environments or in environments with a very strong luminous intensity have a dynamic range that is significantly lower than ordinary images. The user can use this Visibility Enhancement setting to “DEFOG” the image if such “FOGGING” is an issue. This function is only available for EZN3260 Plus. BLC Settings: Back Light Compensation (BLC) is used to make the subject appear clearer when it is set against a bright background. The options vary among models. 
OFF: Select to switch Back Light Compensation functions off. 
Back Light: The Back Light function is useful when the background of the subject is very bright and the subject itself is dark. Select Back Light and adjust the slide bar to the left / right for setting up the back light value. The higher the value, the more the backlight compensation. 
Front Light: This function is useful when the bright highlights, such as flashlight or car headlights, appear on the camera view. Select Front Light and adjust the slide bar to the left / right for setting up the front light value. The higher the value, the more the highlight compensation. 
ON (BLC): This option is useful when the background of the subject is very bright and the subject itself is dark. The BLC will measure the light of the image center and the lens iris will automatically set for optimal image quality. For EZN3160 Plus: Select ON (BLC), the button next to the Mode drop‐down list will be active (see image below). Click the button, the green setup areas appear on the left screen. Click on the areas to enable / disable the BLC function. The selected areas (in green) will be applied with the BLC function. 43 EZN Plus Series For EZN3260 Plus: You can configure one area to apply the BLC function. Select ON (BLC), the setup buttons appears (see image below). Select Low / Middle / High from the BLC Gain drop‐down list. To set up a BLC area, click the Edit Area button and then click on the blue color tab to turn your mouse cursor into a blue pen. Move the cursor to the position on the right screen where you want the BLC rectangle to start and then click. Move your cursor to the position (diagonally opposing corner) where you want the BLC rectangle to end and then click. The blue area will be applied with the BLC function. 
ON (HLC): This option is only available when you select AES Mode in the Exposure Settings (AE) field. This function is useful when the bright highlights, such as flashlight or car headlights, appear on the camera view. The higher the value, the more the highlight compensation. For EZN3160 Plus: Select ON (HLC), and then select a level from the drop‐down list. The higher the level, the more the highlight compensation. For EZN3260 Plus: HLC Level: Select a level for the HLC setting. The higher the level, the more the highlight compensation. HLC Mode: Select All Day / Night mode to apply the HLC function. HLC Black Mask: Select On / Off to apply the black mask on the selected areas. The over‐exposure portions within the selected areas will be applied with the black mask. Color Tabs: You can set up four HLC areas with different colors. To set up a HLC area, click the Edit Area button and then click on the color tab to turn your mouse cursor into a pen of that color. Move the cursor to the position on the right screen where you want the HLC rectangle to start and then click. Move your cursor to the position (diagonally opposing corner) where you want the HLC rectangle to end and then click. Select ON from the color tab drop‐down list. The rectangular area with the selected color will be applied with the HLC function. 44 EZN Plus Series
Noise Reduction Settings: This limits the amount of digital “video noise” that is usually found in any
video stream, and helps to reduce file size. The higher the level, the more the reduction.
For EZN3160 Plus / 3340 Plus:
Select ON / OFF to enable / disable the Noise Reduction function. Or select Auto to let the camera
automatically enable / disable the Noise Reduction function. Slide the Level bar to set up the level.
The higher the level, the more the reduction.
For EZN3260 Plus:
2D DNR: Select ON to enable the 2D DNR function.
3D DNR: Select ON to enable the 3D DNR function. You can further set up the following settings.

3D Start AGC: Set up the AGC level to automatically start the 3D NR function.

3D End AGC: Set up the AGC level to automatically stop the 3D NR function.

3D Level: Set up the 3D DNR level.

Smart NR: Select ON to enable the Smart NR function. The 3D NR function will be
automatically turned on when a motion event occurs.
White Balance Settings: Select the mode that delivers the best quality image for the camera’s light
environment. There are five options: Auto, Manual, Indoor, Outdoor, One Push.

Auto: Select to let the camera automatically adjust the White Balance. In the Auto mode the
camera computes the white balance value output using color information from the entire
screen. It outputs the proper value using the color temperature radiating from a black subject
based on a range of value from 3000 to 7500K.

Manual: Select to adjust the Red and Blue values yourself in the fields below this field.

One Push: Select to enable the Push button
next to the Mode drop-down field. This will
allow you to force the camera to readjust the white balance every time you push the Push
button. The lens will hold the same focal position until the next trigger command is received.
This function helps to prevent incorrect focusing in dark environments. This function is only
available for EZN3160 Plus / 3260 Plus.
Day/Night Settings:

Auto: Select to let the camera automatically switch to Night mode (black and white) when the
light levels fall to a specified level, and back to Day mode (color) when the light levels rise to a
specified level.

Day: Select to keep the camera in Day mode (color), even in nighttime.

Night: Select to keep the camera in Night mode (black and white), even in daytime.
IR Smart Settings: Select ON and set up the level to enhance the image quality when the images are
over exposure. This function is useful when the camera is in the Night mode. This function is only
available for EZN3260 Plus.
45
EZN Plus Series
Saturation: Set the saturation value. This function is only available for EZN3160 Plus / 3340 Plus.
Monitor Type: Select a gamma value from Set 1, Set 2 or Set 3. This function is only available for
EZN3160 Plus.
Negative: Switch this setting ON to view a color negative version of the video image. This is useful
at night or when viewing temperature-sensitive images.
Sharpness Settings: Select the sharpness level of the image. A low sharpness level will deliver a
softer, less detailed image. A high level will deliver a sharp, highly detailed image. Switch Resolution
Enhancement ON to enable the resolution enhancement function.
(Auto) Contrast: Select the contrast level of the image.
Suppress Function: This function is only available for EZN3340 Plus.
Aperture Compensation Suppression: (OFF/Low/Middle/High) This setting can be activated to
suppress luminance noise when the AGC level increases.
Chroma Suppression: (OFF/Low/Middle/High) This setting can be activated to suppress
chrominance noise when the AGC level increases.
Ygamma: (gamma 2.2/standard/contrast enhance/high light range mode L/High light range mode
H). Select the Ygamma value for the video quality of the monitor. This function is only available for
EZN3340 Plus.
Monitor Settings: The user can use this field to optimize video quality for his or her specific type of
monitor – LCD or CRT. This function is only available for EZN3260 Plus.
Color Space Standard: The options are YUV601 for SD and YUV709 for HD. These define the color
space standard required to convert an RGB picture to a YUV picture. Generally, YUV601 is used for
Standard Definition (720P) devices and the YUV709 is used for High Definition (1080P) devices.
Click Apply to save all changes. Click Reset to cancel all changes.
46
EZN Plus Series
7.4.4
ROI (Region of Interest)
The Region of Interest (ROI) function allows users to set up multiple regions within an image with
better quality and less distortion than the rest of the image. You can also use this function together
with the Digital Zoom function on the Live View Page to get a better image result. Up to eight ROIs can
be configured in the ROI settings page.
To set up an ROI region:
1. Select an ROI number from the ROI No. drop-down list.
2. Click the Add button, the mouse cursor will turn into a pen when you move it over the live image
on the left.
3.
4.
5.
Move the cursor to the position where you want the ROI rectangle to start and then click. Move
the cursor to the position (diagonally opposing corner) where you want the ROI rectangle to end
and then click.
Slide the Quality bar to set up the quality value.
Click the Apply button to apply the settings, or click the Reset button to reset without saving the
settings.
47
7.4.5
EZN Plus Series Privacy Mask The Privacy Mask can block out sensitive areas from view, covering the areas with colored or black and white boxes in both live view and recorded clips. This feature is useful when users’ don’t want the sensitive information visible. Up to four Privacy Masks can be configured. 【Privacy Mask Color Settings】The Modes vary among camera models. Mode: Click Color to make the masks appear as colored rectangles on the screen. Click B/W to make the masks appear as gray rectangles on the screen. Click Mosaic to make the masks appear as mosaic‐effect rectangles on the screen. Level: Select the color of the masks if you selected Color Mode. Select the level of grayness of the masks if you selected B/W Mode. Select the level of small/middle/large if you selected Mosaic Mode. Click Apply to apply the settings, or click Reset to reset without saving the settings. Color Tabs
: Click on a color tab to turn your mouse cursor into a pen of that color. You can now create a block of that color on the video screen. Move your cursor to the position where you want your mask rectangle to start and then click. Move your cursor to the position (diagonally opposing corner) where you want your mask rectangle to end and then click. The rectangular area with the selected color will appear. The live image will display the rectangular area with the color you selected. If you want to create another mask, use one of the other three colors. Each color denotes a different mask area. Only one block per color is allowed. As the number of colors suggests, you can configure up to four blocks. Select All: Click to turn the whole screen into a mask area. Clear All: Click to delete all configured mask blocks. Eraser: Click to turn the mouse cursor into an eraser to delete any block you click on. 48 EZN Plus Series
Area: Shows the color and number of the block.
Enable: Check this box to enable the related mask block.
Click Apply to apply the settings, or click Reset to reset without saving the settings.
49
EZN Plus Series
7.5
Audio
The EZN Plus series IP camera can transmit audio to your computer if you have connected an external
microphone to its audio Input cable. It can also receive audio input from you and transmit it via an
external speaker, if you have connected such a speaker to its audio Output cable.
Check the Enable Audio box to enable the camera’s audio function. The camera will now act as a
digital bridge (via the IP network) between any connected audio input device and any connected
audio device.
Adjust the Audio Input Volume if you have external audio input devices (microphones) connected to
the camera and if there are problems with the sound input being too low or high.
Click Apply to save all settings, or click Reset to cancel.
50
EZN Plus Series
7.6
User
7.6.1
User Information
The system administrator can create up to ten user accounts on this page.
To set up a user account:
1. Highlight a user account and click the Modify button. The following dialog box appears.
2. Type the account name, account description and password for the account. Type the password
again in the Confirm field.
3. Select an authority level for the user account from the Authority drop-down list.
•
Supervisor / Administrator: The only difference between a supervisor and administrator is
that a supervisor can edit an administrator’s account and password, but an administrator
cannot edit the supervisor’s account and password. Multiple administrators can be
configured, but there can be only one supervisor. The supervisor and administrators all
have unrestricted access to the Settings submenus and can determine the registration of
all other users.
•
User: A user can view the Live View page and view the system, network, video, and audio
information. A user can only adjust the User Config page settings. The user does not have
access to the User, Event and System pages.
51
EZN Plus Series
4.
5.
6.
7.
• Guest: The lowest level of access, which only allows the user access to the Live View page.
Select Active or Disable from the Status drop-down list to active or disable the user account.
Click On in the SD Card Playback field to allow the user to access the SD card playback
function.
Click OK.
Click Apply to save all the settings.
52
EZN Plus Series
7.6.2
IP Address Filter
Use this page to specify IP addresses that are not allowed to access this camera. By default, any IP
address can access the camera.
Note: The Allowed List addresses only become relevant when the Denied List contains a network or
range, and the supervisor wants to allow one or more IP addresses within that excluded range or
network. In such a scenario, the user would enter the excluded range or network in the Denied List,
and enter the exceptions in the Allowed List.
To set up the IP Address Filter:
1. Select Denied List. Click the Add button, the following dialog box appears.
2. Select an IP type from the IP Type drop-down list.
3. Select a network rule from the Rule drop-down list, type the IP address and click OK.
Single: Type a single IP address in the IP Address field below.
Network: Type the IP address and subnet mask in the field below.
Range: Type a range for the IP addresses.
4. If you have set up an IP range in Step 3, you can optionally set up the Allowed List to allow one
or more IP addresses within the setup IP range to access the IP camera.
5. Click Apply.
53
EZN Plus Series
7.7
Event
You can set up the Motion Detection event, Tamper Detection event or the Alarm I/O to automatically
notify the users when an event occurs or an alarm is triggered. You can also set up a schedule to
automatically record the videos when an event occurs or an alarm is triggered.
7.7.1
Event Settings
You can create a total of ten event or alarm settings page in the Event List
【Event List】
Click the Add button, and the following Event Configuration Window appears.
54
EZN Plus Series
Enter Event Name: Type an event name.
Event Triggered by: Select an event or alarm type for the to-be-specified-below reaction/s.
Alarm Input: Select this if you want a reaction trigger coming from any external, connected sensor
to activate a to-be-specified-below reaction/s via the camera system. Make sure that a suitable
device is actually connected to the alarm input relay.
Manual Trigger: Select this option if you want to manually trigger the alarm by clicking the Trigger
Event button on the Live View Page.
Motion Detection: Select this option if you want motion in a specified part of the camera’s viewing
rectangle (the screen image) to trigger the to-be-specified-below reaction/s.
Tampering Detection: Select this option if you want the camera’s tampering detection sensor to
trigger the to-be-specified-below reaction/s.
Schedule Recording: Select this option if you want the Schedule Recording periods configured in
the recording schedule (the Settings > Event > Schedule page) to activate this event. In this
scenario, a preconfigured event reaction like a log entry will list the start and end times of each
period. Actual recording will only be triggered if the event is preconfigured to do so.





Enable This Event: Select to activate the event.
Enable Re-trigger: Click to set a minimum time after the event is triggered before the event
can be triggered again.
Enable Pre-trigger Buffer: Click if you want the Event reaction (as selected in the “Notification
Over” field below) to be the activation of the video recording function, and if you want the
recording to include the video feed from the time period (configurable on the previous “Event
Settings” page) just before the Event trigger occurred.
Enable Post-trigger Buffer: Click if you want the Event reaction (as selected in the Notification
Over field) to be the activation of the video recording function, and if you want the recording
to include the video feed from a time period (configurable on the Event Settings page) just
after the Event trigger occurred.
Motion Area: Select a setup motion detection area from the drop down list. Note this
function only becomes relevant after the Motion Detection areas have been set up (see 7.7.2
Motion Detection).
Notification Over: Select the desired notification types form the following items.


Log: Click if you want the camera to list the event’s details in its log if the event is triggered.
Trigger Alarm Output: Click if you want the camera to relay the event reaction to a device
attached to the alarm relay output wire and then set up the alarm output duration time.
55
EZN Plus Series



Send Mail Notification: Click if you want the camera to send an Event notification email to the
email address entered in the Set SMTP Server(email) field of the Network > SMTP/FTP page, if
the Event occurs (see 7.3.3 SMTP / FTP).
Upload to FTP: Click if you want the camera to upload recorded footage to the FTP server
entered in the Set SMTP Server(email) field of the Network > SMTP/FTP page, if the Event
occurs (see 7.3.3 SMTP / FTP).
Record to SD Card: Click if you want the camera to start recording its video feed (when the
event occurs) on an on-camera SD Card (if such a card has been inserted).
Note: The recording will only be as long as the combined Pre- and Post-trigger Buffers, so
make sure you enable at least one of these buffers, especially the Post-trigger Buffer.

Record to PC: Check this box if you want the camera to start recording its video feed (when
the event occurs) on the same folder on the same PC as configured on the User Config > User
Config page (if such a folder has been enabled and configured).
Note: The recording will only be as long as the combined Pre- and Post-trigger Buffers (and
for as long as the event trigger is happening – e.g. a motion is detected), so make sure you
enable at least one of these buffers, especially the Post-trigger Buffer.

Network Alarm: Check this box if you want the camera to send a network alarm signal (when
the event occurs) to the CMS servers configured on the Network > Network Alarm page (see
7.3.6 Network Alarm).
Click OK to save all settings, or click Cancel to cancel.
【Pre/Post Trigger Settings】
Pre-trigger Buffer: Select the duration for the buffer. This will determine the amount of footage
(length of time) before the event trigger moment that will be included in an event-triggered video
recording, if that buffer and video recording has been enabled in the Event Configuration Window.
Post-trigger Buffer: Select the duration for the buffer. This will determine the amount of footage
(length of time) after the event trigger moment that will be included in an event-triggered video
recording, if that buffer and video recording has been enabled in the Event Configuration Window.
Click Apply to save all settings, or click Reset to cancel.
56
7.7.2
EZN Plus Series Motion Detection Use this page to configure up to four areas in which motion will be detected. When a motion is detected by the camera, the motion detection icon will appear at the top right of the Live page to alert the user. This function can also be linked with correctly configured Events to trigger Event reactions like the activation of video recording periods, snapshots, alarms, etc. Color Tabs
: Click on a color tab to turn your mouse cursor into a pen of that color. You can now create a block of that color on the video screen. Move your cursor to the position where you want your detection rectangle to start and then click. Move your cursor to the position (diagonally opposing corner) where you want your detection rectangle to end and then click. The rectangular area with the selected color will appear. This block will be an area inside which the camera will detect motion. If you want to create another detection area, use one of the other three palette colors. Each color denotes a different detection area. Only one block per color is allowed. As the number of colors suggests, you can configure up to four blocks. Select All: Click to turn the whole screen into a motion detection area. Clear All: Click to delete all configured motion detection blocks. Eraser: Click to turn your mouse cursor into an eraser to delete any block you click on. Area: Shows the color and number/ID of the block. Enable: Check this box to enable the related motion detection block. Sensitivity: Set the sensitivity of the motion detection sensor function. Click Apply to save all settings, or click Reset to cancel. 57 EZN Plus Series
7.7.3
Tamper Detection
Use this page to set the number of seconds that an alarm signal will be active if the device is physically
tampered (moved, covered up, or out of focus.
7.7.4
Alarm I/O
Use this page to set the type of trigger input and the type of output contact for each of the camera’s
two configurable alarm channels.
58
EZN Plus Series
7.7.5
Schedule
Use this page to configure a schedule for periods during which the camera should deactivate all
user-activated Events (gray Deselect periods), or when the camera should deactivate all user-activated
Events, except Schedule Recording (SR) events (blue Schedule Recording-only periods), or when the
camera should deactivate only SR events (red Event Recording-only periods), or when it should enable
all activated Events (yellow periods).
Event Recording: Click this button to make every hour block you click on red. A red block represents
an Event Recording-only block, which represents an hour when the camera will deactivate all
preconfigured, activated Schedule Recording events and keep all the other activated events active.
Schedule Recording: Click this button to make every hour block you click on blue. A blue block
represents a Schedule Recording-only block, which represents an hour when the camera will
deactivate all other preconfigured, activated events and keep only the preconfigured, activated
Schedule Recording events active.
Event + Schedule: Click this button to make every hour block you click on yellow. A yellow block
represents an hour in which all activated events, including Schedule Recording events, will be
active.
Deselect: Click this button to make every hour block become grey. A grey block represents an hour
in which all activated events, including Schedule Recording events, will be inactive.
Click Apply to save all settings, or click Reset to cancel.
59
EZN Plus Series
7.8
System
You can set up the system’s time and SD card settings, and to do maintenance and reset actions like
reboots and upgrades.
7.8.1
Date/Time
【Machine Name Settings】If required, enter a new name for the machine. This name will be visible
in the Machine Name field of the IP Utility software, which is included in the software CD.
【Set Time Zone】Set the time zone of the camera’s location.
【Set Date/Time Manually】Set the date/time here if you won’t be using an NTP server to update the
date/time (see below).
【Set Date/Time Sync.】Enter the Network Time Protocol server, if applicable. The camera’s time will
be automatically adjusted by synchronizing with the NTP server.
Click Apply to save all settings, or click Reset to cancel.
60
EZN Plus Series
7.8.2
Daylight Saving
Click Enable Daylight Saving to enable this schedule, and select the dates when the region’s daylight
saving period begins and ends. Click Apply to save all settings, or click Reset to cancel.
7.8.3
SD Card
Use this page to prepare the system for safely removing the SD Card from its slot.
【Setup SD Card】
Notification: Select the percentage of storage space that should be left on the card before the
camera notifies you of the impending storage shortage or overwrite.
Event Recording: Select if you want Event Recording only, FTP Backup only, or both.
Overwrite: Click ON if you want the card to start writing over recorded footage when its memory is
full. Click OFF if you want the card to stop recording new footage when its memory is full.
【SD Card Utility】
Capacity: This shows you how much card memory has been used and how much memory capacity
remains on the card.
Remove: Click this button before removing the card from the system.
Format: Click this button to format the card. All data saved on the SD card will be removed if the
card is formatted.
61
EZN Plus Series
7.8.4
Maintenance
【Maintenance Server】
Reboot: Click this button to reboot the unit without changing any of the settings. Use this function if
the unit is not behaving as expected.
Restore: Click this button to restart and reset most of the current settings to their factory default
values. The only settings that will not be changed to default are:
• IP settings
• DDNS settings
Default: The Default button should be used with caution. Pressing this button will return all of the
camera's settings, including the IP address, to the factory default values. The camera will then have
to be reconfigured.
【Save/Load Configuration Server】
Save: To make a backup file of the machine’s current configurations, press Save to save all the
configurations to a config. file. This will enable the user to reload these configuration settings if the
settings are changed and there is unexpected behavior.
Load: To load a previously saved configuration, press the Browse button to locate the saved config.
file (see above) and then click the Load button. The system’s settings will be restored to the saved
configuration.
62
EZN Plus Series
【Save/Load Video Configuration Server】
Save: To make a backup file of the machine’s video configurations, press Save to save the video
configurations to a config. file. This will enable the user to reload these configuration settings if the
settings are changed and there is unexpected behavior.
Load: To load a previously saved video configuration, press the Browse button to locate the saved
config. file (see above) and then click the Load button. The system’s settings will be restored to the
saved video configuration.
【Upgrade Firmware】Click the Browse button to find a previously prepared firmware upgrade file.
Click Upgrade to install the new firmware.
Note:
1. Do not disconnect power to the unit during the upgrade sequence. The unit will reboot
automatically after the upgrade has completed (1-5 minutes).
2. During the upgrade process, all event recording actions will be stopped. Event recording
actions will resume after the camera is rebooted.
63
8.
EZN Plus Series Upgrading Firmware Using IP Utility You can upgrade the Firmware using the IP Utility software included in the software CD. 1.
Install and then start the IP Utility . The following dialog box appears. 2.
Click Find Devices to search the cameras connected in the LAN. The default network values of the cameras will be displayed. By default, the network protocol of the camera is DHCP. 3.
Select a camera and then click Login/Multi Login to log in the camera. 4.
Type the user ID and password. Click OK. Note: 1. The default user ID is user1 and the default password is 11111111. 2. If you select more than one camera that has the same user ID / password, you will be able to log in several cameras at once. 64 EZN Plus Series
5.
Click Upgrade Firmware. A browsing window appears.
6.
Select the firmware file (.evb) and then click Open. The IP Utility will automatically upgrade the
firmware.
The camera will reboot once the update is complete. Click Find Devices, the new firmware version
should be displayed in the last part of the Machine Name.
65
EZN Plus Series
9.
Specifications
Model
EZN3160 Plus
EZN3260 Plus
EZN3340 Plus
Camera
Image Sensor
1/3" Panasonic CMOS
1/3" Panasonic CMOS
1/2.8” Sony CMOS
Megapixel
1.3 MP
2 MP
3 MP
Picture Elements (H x V)
1280 x 1024
1944 x 1092
2048 x 1536
Min. Illumination
0 lux at F1.3 (IR on)
Electronic Shutter
1/125 ~ 1/60,000 s
Scanning System
NTSC / PAL
WDR
Yes
Yes
No
Digital Zoom
10x
BLC
Yes
Gain Control
Yes
White Balance
Yes
Lens
Lens Type
Varifocal
Focal Lens
2.8 ~ 10 mm
Day / Night
Yes (with removable IR-cut filter)
Angle of View
Horizontal Wide 100° / Tele 27°
Vertical
Wide 73° / Tele 20°
IR Distance
40 m / 131 ft
IR LED Quantity
44
Video
Video Compression
NTSC
2048 x 1536, 1920 x 1200 (for EZN3340 Plus only)
1920 x 1080 (for EZN3260 Plus / 3340 only Plus)
1280 x 1024, 1280 x 720, 1024 x 768, 720 x 480, 704 x 480, 640 x 480, 352 x
240, 320 x 240, 160 x 120
PAL
2048 x 1536, 1920 x 1200 (for EZN3340 Plus only)
1920 x 1080 (for EZN3260 Plus / 3340 Plus only)
1280 x 1024, 1280 x 720, 1024 x 768, 720 x 576, 704 x 576, 640 x 480, 352 x
288, 320 x 288, 160 x 120
Resolution
Frame Rate
H.264 and MJPEG
30 fps at 1280 x 1024
30 fps at 1920 x 1080
66
15 fps at 2048 x 1536
EZN Plus Series
Audio
Audio Streaming
Two-way audio
Audio Compression
G.711
Network
Interface
10 / 100 Base-T Ethernet, LAN / PoE Cable
Supported Protocols
TCP/IP, IPV6, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, SNMP, FTP,
HTTP, HTTPs, PPPoE, UPnP, Bonjour, RTP, RTSP, RTCP, IGMP, ARP,
ONVIF, PSIA
Mechanical
Memory Card
One micro SD / SDHC card slot
LAN / PoE Cable
Connects to a 10 / 100 Base-T Ethernet or PoE
Camera
Angle
Pan
360°
Tilt
90°
Adjustment
Rotate
360°
Alarm In/Out
4-Pin terminal block
Audio Input
3.5mm stereo socket (pink)
Audio Output
speaker (green)
Power
12V DC input
4-Pin Data
Cable
General
Power Source
12V DC / PoE (IEEE802.3af)
Power Consumption
(IR LEDs On)
9W (DC 12V)
12.25W (PoE)
9W (DC 12V)
12.85W (PoE)
Humidity
-40°C ~ 55°C / -40°F ~ 131°F (DC 12V)
-20°C ~ 55°C / -4°F ~ 131°F (PoE)
20% ~ 80% (no condensation)
Safety
CE, FCC
Dimensions (L x W x H)
359.9 x 95.5 x 95.5 mm / 14.17 x 3.76 x 3.76 in
Weight
1.62 kg / 3.57 lbs
Operating Temperature
67
8W (DC 12V)
11.5W (PoE)
EverFocus Electronics Corp.
EverFocus Taiwan:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 2380
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495
www.everfocus.de
info@everfocus.de
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY
11788, USA
TEL: +1 631 436 5070
FAX: +1 631 436 5027
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
5F, Kinshicho City Building, 2-13-4
Koto-Bashi,Sumida-Ku, Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
EverFocus Europe - UK:
Unit 12, Spitfire Business Park,
Hawker Road, Croydon Surrey, CR0 4WD, UK
TEL: +44 20 8649 9757 / +44 845 430 9999
FAX: +44 20 8649 9907
www.everfocusuk.co.uk
salesuk@everfocus.com
EverFocus India:
Suite 803, Housefin Bhavan, C-21,
Bandra Kurla Complex, Bandra (East),
Mumbai 400051, India
TEL: +91 22 6128 8700
FAX: +91 22 6128 8705
www.everfocus.in
sales@everfocus.in
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605PZ3160B010A-Ver.A