ES340 Chassis
User Manual
Chenbro
ES340
Chassis
User Manual
www.chenbro.com
1
ES340 Chassis
User Manual
Copyright
Copyright © 2007 Chenbro Micom Co., Ltd.. All rights reserved.
Unless otherwise indicated, all materials in this manual are copyrighted by Chenbro Micom
Co., Ltd.. All rights reserved. No part of this manual, either text or image may be used for any
purpose other than internal use within purchasing company. Therefore, reproduction,
modification in any form or by any means, electronic, mechanical or otherwise, for reasons
other than internal use, is strictly prohibited without prior written permission.
Chenbro Micom Co., Ltd. reserves the right to make improvement and modification to the
products indicated in this manual at any time. Specifications are therefore subject to change
without prior notice.
Information provided in this manual is intended to be accurate and reliable. However,
Chenbro Micom Co., Ltd., assumes no responsibility for its use, nor for any infringements upon
the rights of third parties, which may result from its use.
Technical Support
Chenbro works hard to offer our customers maximum performance from our chassis.
But in case you have any problem with our product you can find supports from the
following resources.
Web Support
Detail information of our products is in our website. You can find technical updates, installation
guides, FAQs, Technical specifications and more. Our web address is: www.chenbro.com.
Email Support
You can also fill out the technical support form at our Technical Support page. You technical
issue inquiries will be sent directly to our support professionals.
Phone Support
You can also contact Chenbro HQ or branch office for immediate support; contact
Information is as following:
Chenbro HQ
Tel: 886-2-8226-5500
Fax: 886-2-8226-5423
Chenbro Europe B.V.
Tel: 31-40-295-2045
Fax: 31-40-295-2044
Chenbro Beijing
Tel: 86-10-8274-3036~ 39
Fax: 8610-8274-3035
Chenbro Micom (USA) Inc.
Tel: 1-909-947-3200
Fax : 1-909-947-4300
Preliminary Edition Aug 2007
www.chenbro.com
2
ES340 Chassis
User Manual
Content
Packing list ……………………………………….…………………………4
Features …………………………………………..……………………………6
Technical specification ………………………..………………………........6
Opening the chassis …………………………..…………………………….7
Installing devices ……………………………..……………………………10
Installing Mini-ITX M/B …...………………...……………………….........10
Installing Slim-CDROM ……...……………..……………………………10
Installing 3.5” Hot-swap hard drive …...…...……………………………..11
Installing card reader ……..……………………………………………….12
Installing heatsink ………………………..……………………………..13
Installing riser card ………………………..…………………………….14
Installing 2.5” internal hard drive ………….……………………………..14
Connecting devices ………………………..……….……………………15
Connecting SATA2 HDD …...……………...………………………..........15
Connecting the power …...………………...……………………..............15
Connecting front panel I/O and LEDs ..…...…………………...….........16
Power adaptor and backplane ….…..……….……..…….………………18
Power Adaptor Specification …………….….….………………………....18
Power Distribution Board ……….……….….….………………………....19
SATA2 Hot-swap Backplane ……………..….….………………………....20
www.chenbro.com
3
ES340 Chassis
User Manual
Packing List
z
ES340 chassis
SATA2/SAS
Shield USB 2.0
SATA 7-pin Cable,
Backplane (2)
Cables (1)
260mm (2)
Power Distribution
Hot-swap HDD
Slim-CDROM
SATA 7-pin Cable,
Board (1)
Carrier (4)
Carrier (1)
360mm (2)
Split Power Cable,
Split Power Cable,
Split Power Cable,
Type-II (1)
Type-II (1)
Type-II (1)
70mm fans (2)
Intrusion Switch (1)
z
Power adaptor kit
120W Power Adaptor (1)
www.chenbro.com
Power Cord (1)
4
ES340 Chassis
User Manual
z
Accessory pack
Screw Pack for
Slim ODD Adaptor
MB (1)
(1)
Power Cable, Big 4P
Screw Pack for
PCI Add-on Card
to Small 4P (1)
HDD (1)
Cable Tie (1)
Front Bezel Key (1)
Bracket (1)
Optional Kits
There are optional kits for different purposes, please contact our sales for more
information and availability.
PCI 32-bit Riser Card (1)
www.chenbro.com
4-in-1 Card
Active Heatsink for
Reader (1)
AMD/Intel LV CPU (1)
5
ES340 Chassis
User Manual
Features
z
Silver-gray powder coating combined with simple lining
z
Ideal for high storage capacity (Hot-swap HDDs) with RAID-5 functionality
z
Available for multi-media platform
z
9.5 liters small form factor with Mini-ITX M/B
z
Removable M/B carrier for excellent thermal performance & easy cabling
z
External adapter reduces noise level
z
Optional remote control & riser card
Technical Specifications
Model Name
◆ES340
M/B Form Factor
◆Mini-ITX, Mini-DTX
Dimension (DxWxH)
◆260mm x140mm x260mm
Drive Bay
◆Hot-swap: 3.5" x 4
PSU
◆Form Factor: External Adapter
Indicator
◆Power, HDD Activity, 2 x LAN, Fault
Front Control
◆Power, Reset, 2 x USB 2.0
Front Access
◆2 x USB 2.0,
Security
◆Kensington Lock Supported, Padlock Loop
Cooling Fan
◆Front: 60mm (Optional)
Slot Opening
◆1 x Low Profile (Optional)
Material
◆SECC
Plastic Material Type
◆ABS-HB
Sheet Metal Thickness
◆0.8mm
Net Weight
◆4.5 Kgs
Gross Weight
◆7.0 Kgs
Backplane
◆SATA2/SAS
Container Info.
◆Internal: 2.5" x 1
◆Slim ODD: 1
◆SD/Mini-SD/MMC/MS Card Reader (Optional)
◆Single Packing
◆Bulk Packing + Pallet
www.chenbro.com
◆10.24" x 5.51" x 10.24"
6
◆Rear: 2 x 70mm
20'
40'
40'H
560
1160
1305
X
X
X
ES340 Chassis
User Manual
Opening the Chassis
Overview
Side Panel w/Venting
Slim CD-ROM Carrier
Main Cable Through Hole
w/Rubber pad
Front Bezel
(w/Key Lock)
Intrusion
Switch
USB & Front
Control Cables
Motherboard Cage
Front
Card Reader (Option)
-- Support MS,SD,Mini-SD,MMC
Slim CD-ROM Cover
USB 2.0 ports x2
Front Control Display:
4x 3.5” HDD Carrier
IR Receiver Lens
„
Power Status LED (Blue)
„
HDD Access LED (Amber)
„
LAN#1 Activities LED (Green)
„
„
LAN#2 Activities LED (Green)
Global Failure LED (Red)
Front Control Switches:
Back
„
Power On Switch
„
System Reset
„
Alarm Mute
Kensington
Pad Lock
Rear 70mm fans (x2)
Side Panel Screws
Power Adaptor Input
I/O Gasket
(Provided by M/B)
www.chenbro.com
7
ES340 Chassis
User Manual
To open the chassis for assembly of internal parts, users need to:
z
Remove the side panel
z
Remove the front bezel
To remove the side panel:
1
2
■ Release the side panel thumb screw on the rear
■ Push and slide the side panel toward rear to open the
chassis
To remove the front bezel:
1
2
■ Lift up the latch along the side to detach the bezel
■ Detach the bezel from Slim ODD side gently
3
4
■ Angle the latch until it is 15 degree away from the
■ gently pull the bezel to make it detach
chassis
www.chenbro.com
8
ES340 Chassis
User Manual
To remove the M/B cage:
1
2
■ Release the secure screws on the M/B cage
■ Release the two screws around the rear fans
3
4
■ Remove the motherboard cage
■ Disconnect the extension fan cables
5
6
■ Detach the motherboard cage with System Cables
(SATA, Power, Fan cables) through the cable routing hole
■ Finish detaching the M/B cage and make sure all the
www.chenbro.com
connection on backplane and PDB are still tight before
assembly back the M/B cage
9
ES340 Chassis
User Manual
Installing Devices:
There are other optional devices for ES340, including:
z Mini-ITX or Mini-DTX
z
z
z
z
Slim Optical Drive
Standard SATA2 Hard Drive
4-in-1 Mini Card Reader (Optional)
Dedicated Universal Heatsink for AMD/Intel CPU
Installing Mini-ITX or Mini-DTX M/B:
1
2
■ Attach the motherboard I/O gasket (provided by M/B)
■ Attach screws to fix the motherboard.
Installing Slim Optical Drive:
Before install the slim CD-ROM, the front bezel must be removed. And the slim CD-ROM
carrier should be apart from the chassis.
1
2
■ Assemble the Slim CD-ROM adapter with attached
screws to the Slim CD-ROM
■ Make sure the Slim CD-ROM is fully seated with holder
clip on the side.
www.chenbro.com
10
ES340 Chassis
User Manual
3
4
■ Slide in the assembled CD-ROM into the chassis
■ Make sure the holder latch is secured when fully
seated
Installing 3.5” SATA2 Hard Drive:
1
2
■ Remove the HDD Carrier from the chassis and place
the SATA2 HDD into it.
■ Attach the HDD screws on both sides
3
4
■ Slide in the assembled HDD into the chassis, suggest
■ Make sure the carrier is fully seated
install by the ID definition on the front panel (No need to
remove the front bezel)
www.chenbro.com
11
ES340 Chassis
User Manual
Installing Card Reader (optional):
1
2
■ Detached the front screw of Card Reader holder
■ Pull out the Card Reader holder
3
4
■ Remove the seal on the holder and make sure the
sockets is right to the opening
■ Attach screws to fix the Card Reader
5
6
■ Connect the short end of USB split cable to Card
Reader with
■ Install the assembled Card Reader back to the chassis
with attach screw
www.chenbro.com
12
ES340 Chassis
User Manual
Installing Dedicated AMD/Intel Heatsink (optional):
The Chenbro heatsink for ES340 is designed specifically to support Intel and AMD
desktop LV (Low Voltage) CPU in universally. Note the CPU power rating should not
over 65W as maximum.
1
2
■ Attach the heatsink retainer on to M/B before install
M/B into the chassis (Note: AMD M/B are preinstalled it)
■ After installing CPU with heat spread, gently clip the
heatsink with metal clipper in one end.
3
4
■ Secure the heatsink clipper in other end
■ Connect the heatsink fan to the M/B
www.chenbro.com
13
ES340 Chassis
User Manual
Installing Riser Card (optional):
1
2
■ The PCI card mounting bracket must be detach and
use special one for mounting, (Ex. PCI RAID card)
■ Connect the cables before install.
3
4
■ Gently install the PCI card with riser into the slot.
(Please pay attention to the cable arrangement)
■ Attach screws on the rear side to secure the PCI card
Installing 2.5” HDD:
1
2
■ Place the 2.5” HDD underneath the Slim ODD
■ Fix the 2.5” HDD with attached screws
Note: (1) To install 2.5” HDD, the M/B cage is required to disassemble.
(2) IDE cable adaptor is required to connect 2.5" IDE HDD to the M/B.
www.chenbro.com
14
ES340 Chassis
User Manual
Connecting Devices:
ES340 is pre-installed with several cables inside as factory default, which
includes:
z
SATA2 cable for Hot-swap hard drive
z
Power cable for M/B
z
Front panel I/O cables
„
USB 2.0 cable
„
4-in-1 card reader (optional)
To connect SATA2 Hot-swap hard drive:
1
2
■ Check the bundled cable with number tag
■ Connect the SATA cables to the M/B properly
Note: If there is not enough SATA ports from M/B, users can either remove or keep the
bundled P3/P4 SATA cable.
To connect the power:
1
2
■ The DC harness comes with 20+4 pin as main
connection for different M/B requirement.
■ Install and secure the DC harness cable to the M/B
properly
www.chenbro.com
15
ES340 Chassis
User Manual
To connect front panel I/O and LEDs:
a. USB 2.0 cable connection
1
■ Front USB cable should be connected to on-board USB
header properly depends on different M/B.
b. Front display cable connection
1
2
■ The display fan-out cable with different connection for:
Power on, HDD, LAN, FAIL and the front switch
■ Connect to the M/B according to the M/B pin header
definition properly.
c. Card reader cable connection (optional)
1
■ After installing the assembled Card Reader, the shorter
USB cable should be connected to the M/B
www.chenbro.com
16
ES340 Chassis
User Manual
d. Slim ODD cable connection (optional)
1
2
■ Use power split cable in accessory pack for conversion
■ Use either standard IDE cable from 3rd party M/B, or
of DC harness, small 4P is connected to the Slim ODD
adaptor board
use optional cable from Chenbro to connect to the Slim
ODD adaptor board
e. Cable management
1
2
■ Due to limited space inside the chassis, make sure all
■ Tie up the cable so the cables are fixed in certain
space.
cable are connected properly and use the cable tie
through the bridge land on side wall
www.chenbro.com
17
ES340 Chassis
User Manual
Power Adaptor and Backplane
Power Adaptor Specification:
For electrical specification:
Input Characteristics
Output Characteristics
Item
Spec
Item
Spec
Rated Input Voltage
100V / 240V
Output Raged Voltage
19V
Input Voltage Range
90VAC to 264VAC
Output Current
6.32A
Input Frequency Range
47Hz to 63Hz
Output Voltage Setting
18.05V~19.95V
Efficiency
86%
In regards of the protection characteristics, this power adaptor will act as power
shut-down automatically base on:
z
Over Current Protection
z
Over Voltage Protection
z
Over Temperature Protection
For the environment operation:
z
Temperature: 0 ~ 40 degC @ Operating and -20 ~ +80 @ Storage
z
Humidity: 20% ~ 80% @ Operating and 10% ~ 90% @ Storage
z
MTBF: > 100,000 hrs
Mechanical characteristics:
z
Dimension: 167mm * 65mm * 37mm
z
Input AC socket type:
z
Output DC cable length: 14#AWG, L=1.8m
www.chenbro.com
18
ES340 Chassis
User Manual
Power Distribution Board:
The PDB (Power Distribution Board) inside the ES340 is a specific DC to DC adaptor,
which only provides the converting from DC19V to multiple voltages include +5V, +3.3V
and +12V for all the devices and boards usage scale up to 180W Power Adaptor. As the
warning message on the back side, any improper 3rd party Power Adaptor may cause
damage to the PDB or internal components.
6Pin
20Pin
4Pin
Connection of DC harness:
1
2
■ When doing the PDB maintenance, please make sure
the cables are plugged properly
■ The single ATX 20-pin connector should be connected
to PDB, another side with split 20+4 pin are for M/B.
Note: Do not plug the DC cable in reverse direction, it will cause serious system and
power adaptor damage
Connect the backplane cables:
1
2
P4
P3
P2
P1
■ Connect the Big-4P power to the backplane
■ The SATA cables (tagged P1~P4) are strongly
recommended to connect following the port orders
indicated as picture.
www.chenbro.com
19
ES340 Chassis
User Manual
2-port SATA2 Backplane Introduction:
ES340 is integrated with two SATA2 backplanes to support four 3.5” HDD hot-swap
feature. With dedicate backplane bracket assembled, users can directly attach the HDD
on the tray and plug into the HDD slot.
Hardware Specification:
Host Interface
SATA 7-pin compatible
HDD Interface
SAS (22+7), SATA2 compatible
Hot-Swap
Yes, allows user to on line replace Hard Disk Drive
Cooling
Five Fan connectors
Environment Monitor
Fan speed detection and temperature detector
Connectors
1.
SATA2 * 2 to host
2.
SAS (22+7) *2 (for HDD ),
3.
Standard 4P Power connector x 1 for +5V, +12V from
power supply
Dimension
206(L) x 20(W) x 2.4(H) mm
Material
FR4 4 layer
Backplane Connectors
SW1
CN2
Rear View
CN23
FAN5
FAN4
FAN3
FAN2
CN1
CN13
CN3
FAN1
B1
CN22
CN12
Front View
www.chenbro.com
20
ES340 Chassis
User Manual
(1) [CN12/CN22] : Connect “22+7”pin SAS connector to HDD
(2) [CN13/CN23] : SATA connector to Host
(3) [FAN1 / FAN2 / FAN3 / FAN4 / FAN5] : Fan connectors
(4) [SW1] : Function Setting Switch
(5) [CN3] : Power Connectors
(6) [CN1] : LED Header
(7) [CN2] : Micro-P Programming Interface (Reserved)
Pin Assignment
[CN1]
Pin
Def.
Pin
Def.
1
NC
2
NC
3
NC
4
NC
5
HDD1 PWR LED+
6
HDD1 PWR LED-
7
HDD2 PWR LED+
8
HDD2 PWR LED-
9
Fail+
10
Fail-
11
Mute+
12
GND
13
NC
14
Key
LED Header
[SW1]
DIP
Def.
On
Off
1
FAN1
Enable
Disable
2
FAN2
Enable
Disable
3
FAN3
Enable
Disable
4
FAN4
Enable
Disable
5
FAN5
Enable
Disable
6
TEMP SETTING
65
55
Setting
7
TEMP SENSOR
Enable
Disable
Switch
8
Reserved
NA
NA
www.chenbro.com
21
Function