Installation and Service Manual
R-Series
Slim Design
Two-Stage R410a
Model Sizes 25-80
Liquid to Air Geothermal Heat Pumps
Maritime Geothermal Ltd.
P.O. Box 2555
Petitcodiac, N.B.
E4Z 6H4
Ph. (506) 756-8135
02 JAN 2014
Email: info@nordicghp.com
Web: www.nordicghp.com
Document Number: 001200MAN-05
ECO 000212
Page 1
DATE : 02 JAN 2014
001200MAN-05
!
SAFETY PRECAUTIONS
!
WARNING: Ensure all access panels are in place and properly secured before applying power to the unit.
Failure to do so may cause risk of electrical shock.
WARNING: Before performing service or maintenance on the heat pump system, ensure all power sources
are DISCONNECTED. Electrical shock can cause serious personal injury or death.
WARNING: Heat pump systems contain refrigerant under high pressure and as such can be hazardous to
work on. Only qualified service personnel should install, repair, or service the heat pump.
CAUTION: Safety glasses and work gloves should be worn at all times whenever a heat pump is serviced. A
fire extinguisher and proper ventilation should be present whenever brazing is performed.
CAUTION: Venting refrigerant to atmosphere is illegal. A proper refrigerant recovery system must be
employed whenever repairs require removal of refrigerant from the heat pump.
MODEL NOMENCLATURE
R—65—HACW—P—1T—C—SDERF—xx
Series:
R = Active Cooling Liquid to Air
Revision:
01, 02 etc.
Nominal Size:
25 = 2 Ton
45 = 3 Ton
55 = 4 Ton
65 = 5 Ton
75 = 6 Ton
80 = 6 Ton Single Stage
Fan Outlet Orientation:
D = Down flow
F = Field Configurable
Functions:
H = Heating
AC = Active Cooling
W = Domestic Hot Water
Fan Motor:
E = ECM (Variable Speed)
Fan Return Orientation:
L = Left Return
R = Right Return
Fan Type:
D = Direct Drive
Refrigerant:
P = R410a
Air Coil:
S = Standard
Voltage Code:
1 = 230-1-60 VAC
2 = 208-3-60 VAC
6 = 220-1-50 VAC
7 = 380-3-50 VAC
Outdoor Loop Exchanger:
C = Copper
Z = Cupro-Nickel (CuNi)
Compressor Stages*:
S = 1 Stage
T = 2 Stage
* 2 stage unless unavailable
due to voltage code, refer to
the Electrical Tables.
001200MAN-05
Page 2
02 JAN 2014
APPLICATION TABLE
SIZE
FUNCTION
REFRIGERANT
VOLTAGE COMPRESSOR
STAGES*
1
25
45
55
65
75
80
HACW
HACW
HACW
HACW
HACW
HACW
FAN/CASE
T
REVISIONS
09
SDELF
SDERF
2
T
6
T
7
T
09
1
T
09
2
T
6
S
7
T
09
1
T
09
2
T
6
S
7
T
09
1
T
09
2
T
6
S
7
T
1
T
P
P
P
P
2
T
6
S
7
T
1
S
P
P
OUTDOOR
COIL
2
S
7
S
C
Z
C
Z
C
Z
C
Z
09
09
SDELF
SDERF
09
09
SDELF
SDERF
09
09
SDELF
SDERF
09
09
09
09
C
Z
SDELF
SDERF
09
09
09
09
C
Z
SDELF
SDERF
09
09
This manual applies only to the models and revisions listed in this table
* T = Two Stage, S = Single Stage
Maritime Geothermal Ltd. has a continuous improvement policy and reserves the right to modify specification
data at any time without prior notice .
02 JAN 2014
Page 3
001200MAN-05
Table of Contents
TABLES, DIAGRAMS & DRAWINGS: ……..……...………….……………………………………………………………… PAGE 5
INSTALLATION INFORMATION: …………………...………….………………………………………………………………
Unit description: …………………………………………………………………………………………………..…...
Unpacking the unit: …………………………………………………………………………………………………...
Optimum Placement: ………………………………………………………………………………………………….
Electrical Connections: ………………………………………………………………………………………………
Control Transformer : ……..…………………...……………………………………………………………………
Circulator Pump Module Wiring (Ground Loop Only): ………………………………………………………….
Thermostat Requirements: …………………………………………………………………………………………..
Fan Motor: ………………………………………………………………………………………………………………
Fan Return Orientation: ………………………...……………………………………………………………………
Fan Outlet Orientation : ………………………...……………………………………………………………………
Safety Controls: ……………………………………………………………………………………………………….
Domestic Hot Water Connections (HACW only): …………………..……………………………………………
PAGE 6
Page 6
Page 6
Page 6
Page 6
Page 6
Page 6
Page 7
Page 7
Page 7
Page 7
Page 7
Page 8
SIZING AND DUCTWORK: ………………...…………………………………………………………………………………… PAGE 11
Heat Pump Sizing: ……………………………………………………………………………………………………. Page 11
Duct Systems - General: …………………………………………………………………………………………….. Page 11
Duct Systems - Grill Layout: ………………………………………………………………………………………… Page 11
Thermostat Location: ………………………………………………………………………………………………… Page 12
Plenum Heater (Optional): …………………………………………………………………………………………… Page 12
Condensate Drain: …………………………………………………………………………………………………….. Page 12
Duct Sizing Guide: ……………………………………………………………………………………………………. Page 14
GROUND WATER SYSTEM INFORMATION: ………………………………………………………………………………… PAGE 15
General Requirements: ………………….…………………………………………………………………………… Page 15
Plumbing the Heat Pump: ……………………………………………………………………………………………. Page 15
Pipe Insulation: ………………………………………………………………………………………………………… Page 15
Water Discharge Methods: …………………………………………………………………………………………… Page 15
GROUND LOOP SYSTEM INFORMATION: …………………………………………………………………………………..
Circulator Pump Module: …………………………………………………………………………………………….
Flushing & Purging the Ground Loop: …………………………………………………………………………….
Adding Antifreeze Solution: …………………………………………………………………………………………
Initial Pressurization: …………………………………………………………………………………………………
Pipe Insulation: ………………………………………………………………………………………………………..
PAGE 18
Page 18
Page 18
Page 19
Page 19
Page 19
STARTUP PROCEDURE: ……………………………………………………………………………………………………….
Pre-start Inspection: ………………………………………………………………………………………………….
Unit Startup: …………..……………………………………………………………………………………………….
Startup Record: ……………….……………………………………………………………………………………….
Page 21
Page 21
Page 22
Page 23
GENERAL MAINTENANCE: ……………...…………………….……………………………………………………………… PAGE 24
TROUBLESHOOTING GUIDE: ………………………………….……………………………………………………………… PAGE 25
Repair Procedures: …………………………………………………………………………………………………… Page 34
MODEL SPECIFIC INFORMATION: …………………..……………………………………………………………………….
Refrigerant Charge Chart: ……………………………………………………………………………………………
Shipping Information: …………………………………………………………………………………………...……
Standard Capacity Ratings: …………..…………………………………………………………………………….
Capacity Ratings: ………..………………..………………………………………………………………………….
Electrical Tables: ………………………………………………………………………………………………………
Electrical Diagrams: ………………………..…………………………………………………………………………
Refrigeration Circuit Diagrams: …………………………………………………………………………………….
Case Details: ………………………….…..……………………………………………………………………………
PAGE 35
Page 35
Page 35
Page 35
Page 37
Page 43
Page 45
Page 49
Page 51
APPENDIX A: Control Board Specifications: ……………………………………………………………………………… PAGE 57
APPENDIX B: ECM Fan Airflow Tables: …………………………………………………………………………………….
PAGE 58
WARRANTY INFORMATION: ………………………………………………………………………………………………….. PAGE 60
001200MAN-05
Page 4
02 JAN 2014
Tables, Diagrams and Drawings
TABLES
Table 1 - Power Supply Connections (Heat Pump): ……………...………………………………...…..……....
Table 2 - Power Supply Connections (Optional Plenum Heater): ………..……………………...…..……....
Table 3 - Control Signal Description: …….………………………………………………………………..……....
Table 4 - Airflow Selections: ………………………………………………………………………………………...
Table 5 - Control Board Fault Codes: ……...……………………………………………………………………...
Table 6 - Heat Pump Size vs. Heated Area for Ground Loop Systems: …..………………………………...
Table 7 - Heat Pump Size vs. Heated Area for Ground Water Systems: ….………………………………...
Table 8 - Heat Pump Size vs. Hot Air Grills: …..………………………………….……………………………...
Table 9 - Plenum Heater Sizing: …..………………………………………………..……………………………...
Table 10 - Duct Sizing Guide: …………………………………………………...………………………………...
Table 11 - Required Flow and Air Tank Sizing: …..……………………………………………….……………...
Table 12 - Antifreeze Percentages by Volume: ………………………………..………………………………...
Table 13 - Volume of Fluid per 100ft. Of Pipe: …..………………………………….…………………………...
Table 14 - Refrigerant Charge Chart: …..………………………..………………….….………………………...
Table 15 - Shipping Information: ………...………………………..………………….….………………………...
Table 16 - Standard Capacity Ratings - Ground Loop Heating 60Hz: …………..…………………………...
Table 17 - Standard Capacity Ratings - Ground Water Heating 60Hz: …………….………………………...
Table 18 - Standard Capacity Ratings - Ground Loop Cooling 60Hz: …….…….…………………………...
Table 19 - Standard Capacity Ratings - Ground Water Cooling 60Hz: …..…….………….………………...
Table 20 - Heat Pump Electrical Information (208/230-1-60): …..…………………….……..………………...
Table 21 - Heat Pump Electrical Information (208-3-60): …..…………………….….………………………...
Table 22 - Heat Pump Electrical Information (460-3-60): …..…………………….….………………………...
Table 23 - Heat Pump Electrical Information (220-1-50): …..…………………….….………………………...
Table 24 - Heat Pump Electrical Information (380-3-50): …..…………………….….………………………...
Table 25 - Plenum Heater Electrical Information (208/230-1-60): ……………….….………………………...
Page 6
Page 6
Page 7
Page 7
Page 8
Page 11
Page 11
Page 12
Page 12
Page 14
Page 15
Page 19
Page 19
Page 35
Page 35
Page 35
Page 35
Page 36
Page 36
Page 43
Page 43
Page 43
Page 43
Page 44
Page 44
DIAGRAMS
Diagram A - Typical P/T (Pete’s) Plug & Thermometer Stem: …….……………………….…………..……..
Diagram B - Typical Purge Cart: ……………………………………………………………………………………
Case Details - Left Return - Size 25 to 75: ……..…………….…………...………………………………….…..
Case Details - Right Return - Size 25 to 75: ……..………….…………...………………………………….…..
Case Details - Left Return - Size 80: ……..…………….…………...…………..…………………………….…..
Case Details - Right Return - Size 80: ……..………….…………...….…………..………………………….…..
Page 18
Page 18
Page 51
Page 53
Page 55
Page 56
DRAWINGS
001827CDG - Typical Thermostat Connections: ………………………………………….……………………..
000970PDG - Single Unit Connection to DHW Pre-Heat Tank (Brass FPT): ………………………………..
001201CDG - Typical Duct and Condensate Connections (Modular Case): ……………………………….
000907CDG - Typical Ground Water Installation for Size 25-75 Heat Pumps (Brass FPT): ……………..
000619INF - Ground Water Disposal Methods: …………………………………………………………………
000906CDG - Geo-Flo Circulator Pump Module Installation (Brass FPT): …………………………………
001754SCH-01 - R-25-75-HAC*-P-1*-*-*DE** Schematic Diagram: …………….…………..…………..……
001755ELB-01 - R-25-75-HAC*-P-1*-*-*DE** Electrical Box Diagram: ….…………..………………..………
001135SCH-03 - R-**-HAC*-P-1*-*-*DE** Schematic Diagram: …………….…….…………..…………..……
001136ELB-03 - R-**-HAC*-P-1*-*-*DE** Electrical Box Diagram: …………………..………………..………
001207RCD - R(H)-Series Refrigeration Circuit Diagram—Heating Mode: …….……………………………
001208RCD - R(H)-Series Refrigeration Circuit Diagram—Cooling Mode: …….……………………………
02 JAN 2014
Page 5
Page 9
Page 10
Page 13
Page 16
Page 17
Page 20
Page 45
Page 46
Page 47
Page 48
Page 49
Page 50
001200MAN-05
Installation Information
UNIT DESCRIPTION
The R-Series unit is a high efficiency two-stage geothermal heat pump. Two-stage units offer longer runtimes and fewer cycles resulting in higher efficiency and a higher comfort level. The heat pump contains environmentally friendly R410a
refrigerant.
An electrically commutated (ECM) fan with several speed
options is standard. The motor has a soft start function for improved efficiency and reduced wear.
The unit has several key features that are described in the
specifications document for the particular heat pump. Please
request a copy if desired or visit www.nordicghp.com
The Electrical Tables in the Model Specific section and the
ELB diagram contain information about the size of wire for the
connections, as well as the recommended breaker size for both
the heat pump and optional plenum heater. Connections are as
per TABLE 1 and TABLE 2.
NOTE: There are two separate power supplies, one for the
heat pump and a second one for the plenum heater if installed, each must have its supply wires and breaker.
NOTE: A properly qualified electrician should be retained
to make the connections to the heat pump and associated
controls. The connections to the heat pump MUST CONFORM TO LOCAL CODES.
TABLE 1 - Power Supply Connections
(Heat Pump)
UNPACKING THE UNIT
When the heat pump reaches its destination it should be
unpacked to determine if any damage has occurred during
shipment. Any visible damage should be noted on the carrier's
freight bill and a suitable claim filed at once.
Line
The heat pump is well constructed and every effort has
been made to ensure that it will arrive intact, however it is in the
customer's best interest to examine the unit thoroughly when it
arrives.
OPTIMUM PLACEMENT
For liquid to air units, to achieve the greatest efficiency, the
heat pump should be centrally located in the home with respect
to the conditioned space. This design provides the utmost in
economy and comfort and usually can be accomplished in
harmony with the design of the home. A heating system cannot
be expected to produce an even warmth throughout the
household when it is located at one end of the structure and the
warm air is transmitted with uninsulated metal ductwork.
Voltages
Line 1
All
L2
Line 2
All
L3
Line 3
208-3-60, 460-3-60, 380-3-50
N**
Neutral
208/230-1-60, 208-3-60, 380-3-50
** Only required if connecting 115VAC circulators to the heat
pump for 208/230-1-60 and 208-3-60 models, the heat pump
itself does not require a neutral. Required for 380-3-50 models.
TABLE 2 - Power Supply Connections
(Optional Plenum heater)
Line
L1
Description
Line 1
Voltages
208/230-1-60, 208-3-60
L2
Line 2
208/230-1-60, 208-3-60
Contact factory for three phase plenum heater requirements.
CONTROL TRANSFORMER
If possible the access panels should remain clear of
obstruction for a distance of two feet to facilitate servicing and
general maintenance.
Raising the heat pump off the floor a few inches is generally
a good practice since this will prevent rusting of the bottom
panel of the unit. We recommend that the heat pump be placed
on a piece of 2'' thick styrofoam. The styrofoam will smooth out
any irregularities in the cement floor and deaden any
compressor noise emitted from the bottom of the cabinet.
The low voltage controls are powered by a 75VA class II
transformer. The transformer has a resettable breaker on the
secondary side for circuit protection. Should the breaker trip,
locate and correct the problem and then reset the breaker by
pressing in on it.
IMPORTANT NOTE: For 208/230VAC-1-60 units, if connecting to 208VAC power supply move the red wire connected
to the 240 terminal of the transformer to the 208 terminal of
the transformer.
The heat pumps come equipped with an air-filter rack which
can be installed with the removable end (where the filter is inserted) on either side to facilitate changing the filter.
CIRCULATOR PUMP MODULE WIRING
(GROUND LOOP ONLY)
ELECTRICAL CONNECTIONS
The heat pump has a concentric 1.093” / 0.875” knockout
for power supply connection to the electrical box, as well as one
for connection to the circulator pump module for ground loop
applications. There are two 1/2” openings with plastic grommets (grommet hole is 3/8”) in the upper section of the electrical
box, one for the thermostat connections, and one for the optional plenum heater connections.
A schematic diagram (SCH) and electrical box layout
diagram (ELB) can be found inside the electrical box cover of
the unit as well as in the Model Specific section of this manual.
001200MAN-05
Description
L1
The heat pump has provisions for connecting the circulator
pump module so that the pumps will be turned on whenever the
compressor operates. Connect the circulator pump module to
the appropriate two terminals of the terminal strip marked
OUTDOOR CIRCULATORS in the heat pump, as per the voltage of the circulator pump module. Ensure that the total current
draw does not exceed the value indicated on the label in the
heat pump electrical box. Refer to the electrical box drawing
on the electrical box cover for more information.
Page 6
02 JAN 2014
THERMOSTAT REQUIREMENTS
The R-Series model requires a three-stage heating and
two stage cooling heat pump configurable thermostat for twostage models. The stages are S1 = Stage 1 compressor, S2 =
Stage 2 compressor and S3 = electric auxiliary (heating only).
One can be purchased with the unit, or other heat pump thermostats with the same number of stages can be used. The electrical box diagram on the electrical box cover provides a description of the signal connections as in TABLE 3. Refer to DRAWING 001827CDG for a diagram of the connections between the
thermostat and the heat pump.
NOTE: Some models are not available in two-stage at the present time, models numbers with a T in the Compressor Stages
designator are two-stage, models with an S are single stage
(verify the model number against pages 2 and 3 of this manual,
or refer to the Electrical Tables near the end of this manual to
determine if the model is two stage or one stage). The Y2 signal is not used for these units, and they only require a 2 stage
heat 1 stage cool thermostat. The stages are S1 = Compressor
and S2 = electric auxiliary (heating only). If the selected thermostat has more stages than this, configure it for 2 and 1.
retrofits with undersized ductwork, to help reduce air flow noise
in the ductwork. It is recommended that airflow reduction only
be used with the High or Max air flow setting. Care should be
taken to ensure that the unit does not trip a safety control in
heating or cooling mode if the 15% reduction is used in conjunction with the MED or LOW air flow setting.
TABLE 4 - Airflow Selections
Position
-6%
MED
HIGH
MAX
Nominal
+6%
+12%
The R-Series heat pump can be ordered as a left or right
hand return from the factory. This must be specified at time of
order as the physical construction of the two configurations is
different. Refer to the CASE DETAILS section of this manual or
the specification documents for physical dimensions of the units.
FAN OUTLET ORIENTATION
The R-Series heat pumps have a field configurable fan.
It’s default location from the factory is in the top of the unit,
providing a “ninety” in the airflow. It can easily be placed in the
side of the unit for straight through airflow.
Description
C
G
Y1
RH
L
24VAC Common (Ground)
Fan low speed (for air circulation)
Heat Pump Stage 1
24VAC Hot
Fault (24VAC when fault condition)
Heat Pump Stage 3 (auxiliary heat) /
W2
Emergency Heat
O
Cooling Mode (reversing valve)
Heat Pump Stage 2 (Not used for single
Y2
stage units)
AR1
Airflow Reduction*
AR2
Airflow Reduction*
Plenum Heater dry contact
C(I)
(Connect to C or I in plenum heater)
Plenum Heater dry contact.
1
(Connect to 1 and 2 in plenum heater)
* Connect AR1 to AR2 with a dry contact to reduce the airflow by 15%. Refer to the Fan Motor sub-section for more
information.
To switch the location of the fan outlet follow these simple steps:
1. Turn the power of to the unit.
2. Remove the screw that holds the side access panel in
place and remove the access panel by pulling up on
the handle and then outward from the bottom.
3. Disconnect the two wire harnesses and ground wire
from the fan motor.
4. Repeat step 2 for the access panel with the fan
mounted in it. Set the assembly on the floor.
5. Disconnect the plenum heater extension from the fan
housing and from the access panel.
6. Mount the fan housing directly to the access panel.
7. Install the fan/panel in the new location and secure
with the screw.
8. Reconnect both harnesses and ground wire.
9. Install the remaining access panel and secure with the
remaining screw.
SAFETY CONTROLS
FAN MOTOR
The heat pump has two built in safety controls which are
designed to protect the unit from situations which could damage
it should the operation of the refrigeration circuit fall outside the
allowable operating range.
The unit is equipped with a direct drive ECM fan motor for
maximum efficiency. The motor features a soft start which further improves efficiency by eliminating inrush current and provides a smooth, quiet ramp up to speed . The motor will maintain the programmed air flow up to the maximum external static
value. Refer to the APPENDIX B: ECM Fan Airflow Tables.
A. Low Pressure Control
The low pressure control monitors the compressor suction
pressure and will shut the compressor down if the refrigerant
evaporating pressure becomes too low, risking the danger of
freezing conditions in the evaporator.
The air flow can be set to four different levels by changing
the position on the Air Flow board located in the electrical box.
The four levels are indicated in TABLE 4. The actual air flow
values can be found in APPENDIX B.
Units are shipped with the MED position selected for nominal air flow. The air flow can be further reduced by 15% by
making a dry contact across AR1 and AR2 on the terminal strip.
This can be used for applications that have multiple zones, or
02 JAN 2014
LOW
FAN RETURN ORIENTATION
TABLE 3 - Control Signal Description
Signal
Airflow
There are (3) main reasons why this control would activate
in response to the operating conditions of the unit while operating in heating mode:
Page 7
1. Low or no Outdoor loop flow.
2. Low Outdoor loop entering liquid temperature.
3. Dirty or fouled Outdoor loop heat exchanger.
001200MAN-05
DOMESTIC HOT WATER
CONNECTIONS (HACW only)
B. High Pressure Control
The high pressure safety control monitors the compressor
discharge pressure and will shut the compressor down if the
condensing pressure becomes too high.
There are (3) main reasons why this control would activate
in response to the operating conditions of the unit while operating in heating mode:
1. Low or no airflow.
2. High return air temperature.
3. Dirty air coil due to poor filter maintenance.
The port connections for the DHW circuit are 1/2” brass FPT
fittings. They are marked as DHW IN and DHW OUT
A typical piping diagram for a pre-heat tank configuration
can be found in DRAWING 000970PDG at the end of this section. Be sure to note the position of the check valve and the
direction of water flow. Other configurations are possible, and
there may be multiple units tied together in larger buildings.
The unit contains a control board that monitors the safety
controls and operates the compressor accordingly. Refer to
APPENDIX A for control board specifications. The low pressure
control is connected to LP1 and LP2. The high pressure control
is connected to HP1 and HP2.
The control board also has provisions for a flow switch.
The flow switch is unused from the factory and a jumper wire is
placed across the FLOW SWITCH terminals. If a flow switch is
desired, the jumper can be removed and the two leads from the
flow switch can be connected to the FLOW SWITCH terminals
on the safety board. The flow switch is ignored for 5 seconds on
compressor startup to allow time for flow to be established. The
high and low pressure controls are monitored at all times. The
compressor will not be able to start if either of them has a fault.
The control board has an on-board LED and a FAULT
pin with a 24VAC output, which is routed to the L terminal of the
thermostat terminal strip. An external indicator or relay can be
connected across L and C on the terminal strip if external signaling is desired. Should a fault condition occur, the LED will
flash the code of the fault condition while the safety control in
question is open. The codes are shown in TABLE 5. The control board will lock out the compressor for five minutes when a
fault occurs. The control board will then restart the compressor
if the fault has been cleared. Should a second fault condition
occur within a 60 minute period the control board will go into
permanent lockout mode and energize the FAULT pin. The
LED will flash the fault code until the control board is reset by
powering down the unit.
TABLE 5 - Control Board Fault Codes
Fault
!
!
LED Flashes
High Pressure
1
Low Pressure
Flow
2
3
!
WARNING: USE ONLY COPPER LINES TO
CONNECT THE DESUPERHEATER. TEMPERATURES COULD REACH 200F SHOULD THE DHW
CUTOUT SWITCH FAIL, POTENTIALLY RUPTURING
PEX PIPING.
Ensure the tank is filled with water and under pressure
before activating the heat pump. Slightly loosen the boiler drain
on the DHW Out pipe to allow air to escape from the system
before the unit is started. This step will make certain that the
domestic hot water circulator in the unit is flooded with water
when it is started.
!
CAUTION: the domestic hot water pump is water lubricated; damage will occur to the pump if it is run
dry for even a short period of time.
Connect the brown wire with the blue insulated terminal to
L1 of the compressor contactor. Ensure the power is off
when connecting the wire.
The DHW loop may have to be purged of air several times
before good circulation is obtained. A temperature difference
between the DHW In and DHW Out can be felt by hand when
the circulator pump is operating properly.
For the pre-heat tank setup, the final tank should be set to
140°F(60°C), unless local code requires a higher setting. The
pre-heat tank does not require electric elements. This setup
takes full advantage of the desuperheater as it is the sole heat
provider to the pre-heat tank. The desuperheater remains active
during the compressor runtime until the pre-heat tank has been
completely heated by the desuperheater alone. This setup is
more energy efficient than a single tank setup.
!
CAUTION: If two (2) shut-off valves are located on
the domestic hot water ines as shown in the diagram,
a pressure relief valve must be installed to prevent
possible damage to the domestic hot water circulator
pump should both valves be closed.
WARNING: If the control board enters permanent
lockout mode there is a serious problem with the
system and it must be rectified if the unit is to
maintain good service.
WARNING: REPEATED RESETS OF A LOW PRESSURE LOCKOUT COULD CAUSE THE HEAT EXCHANGER TO FREEZE AND RUPTURE, DESTROYING
THE HEAT PUMP AND VOIDING THE WARRANTY.
001200MAN-05
Page 8
02 JAN 2014
02 JAN 2014
Page 9
001200MAN-05
001200MAN-05
Page 10
02 JAN 2014
Sizing and Ductwork
HEAT PUMP SIZING
heat pump are greatly reduced.
TABLE 6 depicts a rough guideline as to the size of home
each heat pump size can handle for ground loop installations.
TABLE 6 - Heat Pump Size vs. Heated Area
for a Ground Loop System
Model
Sq.ft.
Sq.m.
25
800
75
45
55
65
75
80
1,400
2,000
2,600
3,100
3,500
130
185
240
290
325
DUCT SYSTEMS - GENERAL
TABLE 7 depicts a rough guideline as to the size of home
each heat pump size can handle for ground water installations.
TABLE 7 - Heat Pump Size vs. Heated Area
for a Ground Water System
Model
Sq.ft.
1,000
95
45
55
65
75
80
1,800
2,500
3,200
3,800
4,200
165
230
295
355
390
1. Generally allow 100 cfm for each floor grill.
2. All leads to the grills should be 6'' in diameter (28sq.in. each).
3. The main hot air trunks should be at least 75% of the square
surface area of leads being fed at any given point.
4. Return air grills should have a minimum of the same total
square surface area as the total of the supply grills.
5. The square surface area of the return trunks should equal
the square surface area of the grills being handled at any
given point along the trunk.
THE TABLES ABOVE ARE FOR INFORMATION ONLY,
THEY SHOULD NOT BE USED TO SELECT A UNIT SIZE.
They simply show on average what size unit is required for a
typical two-level home (main level and below grade basement)
with R-20 walls, R-40 ceiling and average size and number of
windows. The Heated Area is the area of the main level, The
tables account for a basement the same size as the heated area.
MARITME GEOTHERMAL LTD. HIGHLY RECOMMENDS
THAT A PROPER HEAT LOSS/GAIN ANALYSIS BE PERFORMEDE BY A PROFESSIONAL INSTALLER WITH CSA
APPROVED SOFTWARE BEFORE SELECTING THE SIZE OF
UNIT REQUIRED FOR THE APPLICATION. For heating
dominant areas, we recommend sizing the unit to 100% of
the heating design load for maximum long term efficiency
with minimal supplementary heat. The unit should be installed as per CSA 448.2-02. For ground loop applications,
the ground exchanger should be designed using suitable
software with a multi-year analysis.
There are many factors to consider when sizing the heat
pump. Some of these factors include the number of levels, the
size of the windows, the orientation of the home, attached garage, bonus rooms, walk-in basement, coldest outdoor temperature, etc. The heat loss program will take all of these factors
into consideration in its calculations. An undersized installation
will not be as efficient as it will require excessive relatively expensive supplemental heat to maintain a comfortable temperature in the home, and the cost savings of having a geothermal
02 JAN 2014
Ductwork layout for a heat pump will differ from traditional hot
air furnace design in the number of leads and size of main
trunks required. Air temperature leaving the heat pump is
normally 95º -105ºF (35-40ºC), much cooler than that of a
conventional warm air furnace. To compensate for this, larger
volumes of lower temperature air must be moved and
consequently duct sizing must be able to accommodate the
greater air flow without creating a high static pressure or high
velocity at the floor diffusers.
A duct system capable of supplying the required air flow is of
utmost importance. Maritime Geothermal Ltd. recommends that
the static pressure be kept below 0.2 inches of water total. In
some instances the number of floor diffusers will actually double
when compared to the number that would be used for a hot air
oil-fired furnace. Refer to TABLE 10 at the end of this section.
Sq.m.
25
Once the total heat loss has been calculated, the unit can
be sized using the performance tables (from the specifications
document) in conjunction with the minimum expected entering
liquid temperature of the ground loop (well water temperature for
ground water system). The heat pump output must be able to
match the total heat loss at the selected entering water temperature in order to provide a comfortable environment with minimal
auxiliary heat.
It is VERY IMPORTANT that all turns in both the supply
trunks and the return trunks be made with TURNING RADII. Air
act like a fluid and, just like water, pressure drop is increased
when air is forced to change direction rapidly around a sharp or
irregular corner.
It is recommended that flexible collars be used to connect the
main trunks to the heat pump. This helps prevent any vibrations
from travelling down the ductwork. If a plenum heater is installed, the collar should be at least 12” away from the heater
elements.
The first 5-10 feet of the main supply trunks should be insulated with acoustical duct insulation to further inhibit any noise
from the unit from travelling down the ductwork. If a plenum
heater is installed, insulation should not be placed within 12” of
the heater elements.
Page 11
DRAWING 001201CDG shows a typical installation.
001200MAN-05
DUCT SYSTEMS - GRILL LAYOUT
Most forced air heating systems in homes have the floor grills
placed around the perimeter of the room to be heated. Supply
grills should be placed under a window when possible to help
prevent condensation on the window. As mentioned in the previous sub-section, supply grill leads should be 6'' in diameter (28
sq.in. each) to allow 100cfm of air flow.
In a typical new construction, there should be one supply
grill for every 100sq.ft. of area in the room. When rooms require
more than one grill, they should be placed in a manner that promotes even heat distribution, such as one at each end of the
room. It is always a good idea to place a damper in each grill
supply or place adjustable grills so that any imbalances in the
heat distribution can be corrected.
INSTALLATION—Fan outlet at side of unit: The plenum
heater should be installed in the supply duct in a manner that
allows all of the airflow to pass through it to prevent any hot
spots in the heater elements. Ensure that the plenum heater is
mounted in an approved position as per its instructions.
TABLE 8 - Heat Pump Size vs. Hot Air Grills
Size (tons)
# of Grills (@100cfm)
25
45
55
65
2
3
4
5
8
12
15
19
75
6
21
80
6
24
INSTALLATION—Fan outlet at top of unit: The heat pump
comes equipped with an internal mounting location for the plenum heater. Remove the screws from the cover plate, remove
the cover plate and place the plenum heater in the hole. Secure
it in place with the cover plate screws. Use the indicated knockouts on the heat pump case for electrical connections.
When installation is complete, check the appropriate box
of the label on the unit door to indicate which size heater
was installed.
The total number of supply grills available is based on the
heat pump nominal airflow. TABLE 8 shows the number of
grills available per heat pump size.
Model
The second function of the plenum heater is to provide emergency heat should a problem occur that causes the heat pump
to be locked out. This can be engaged by setting the thermostat
to emergency heat, allowing the plenum heater to function while
preventing the heat pump from operating. Should the heat
pump fail while the home is vacant, the auxiliary function of the
thermostat will maintain the temperature setting of the thermostat.
Only two control wires are needed to connect the plenum
heater to the heat pump terminal strip. Refer to the label on the
plenum heater or the electrical box diagram on the inside of the
electrical box cover of the compressor unit for details on the
connections.
Return grills should be mounted on the floor. At minimum
they should be the same size as the supply grill, it is highly
recommended that they be 25% to 50% larger than the total
supply. They should be placed opposite the supply grills when
possible to ensure distribution across the room. For rooms requiring more than one supply grill, it may be possible to use one
larger return grill if it can be centrally positioned opposite of the
supply grills, however it is preferred to have one return for each
supply to maximize heat distribution across the room.
The plenum heater requires its own separate power supply. TABLE 9 shows the recommended size plenum heater, as
well as the wire size and breaker size needed to provide power
to the plenum heater. Refer to the Electrical Tables for electrical connection information.
TABLE 9 - Plenum Heater Sizing
Heat
Pump
Model
Size
25
45
55
65
75 - 80
THERMOSTAT LOCATION
Most homes are a single zone with one thermostat. The thermostat should be centrally located within the home, typically on
the main floor. It should be placed away from any supply grills,
and should not be positioned directly above a return grill. Most
installations have the thermostat located in a hallway, or in the
inner wall of the living room. It should be noted that most
homes do not have any supply ducts in the hallway. This can
lead to a temperature lag at the thermostat if there is very little
air movement in the hallway, causing the home to be warmer
than indicated by the thermostat.
PLENUM HEATER (OPTIONAL)
For installations that do not already have a backup heat
source such as electric baseboard, wood stove, propane etc, it
is recommended that a plenum heater be installed. This provides two functions.
The first function of the plenum heater is to act as an auxiliary
heat source. As such it will provide additional heat on extremely
cold days if the heat pump is unable to bring the home temperature up quickly enough, eliminating any discomfort to the homeowner.
Plenum Heater Sizes (kW)
Recommended
7
10
10
15
20
Available
5
7
7
10
15
15
20
CONDENSATE DRAIN
The unit comes equipped with a 3/4” PVC socket fitting
(female) labeled “Condensate Drain”. This drain allows the condensate which forms during the air-conditioning cycle to be removed from the unit. The drain should be connected as per
local codes. During high humidity weather, there could be as
much as 25 gallons of water formed per day.
Care should be taken in the spring to ensure that this pipe is
not plugged with dust that has collected during the winter causing the condensate to overflow into the bottom of the heat pump
and onto the floor. The condensate drain is internally
trapped; however, proper venting is required external to
the heat pump. Refer to local codes to ensure the installation is done properly.
DRAWING 001201CDG shows a typical installation.
001200MAN-05
Page 12
02 JAN 2014
02 JAN 2014
Page 13
001200MAN-05
TABLE 10 - Duct Sizing Guide (external static of 0.20”H2O)
Airflow
(CFM)
Minimum
Diameter
Duct Area
(in)
(sq.in)
Return Air
Diameter
(in)
Rectangular Equivalents (in)
37
20
5
2.25 x 10
3x8
3.5 x 6
4 x 5.5
5x5
63
20
5
2.25 x 10
3x8
3.5 x 6
4 x 5.5
100
28
6
3.25 x 10
4x8
5x6
152
38
7
3.25 x 14
4 x 11
212
50
8
4 x 15
226
50
8
277
64
304
5
17
5x5
6
30
5.5 x 5.5
6x6
7
47
5 x 8.5
6x7
6.5 x 6.5
8
72
5 x 12
6 x 10
7x8
8x8
9
100
4 x 15
5 x 12
6 x 10
7x8
8x8
10
107
9
5 x 15
6 x 12
7 x 10
8x9
8.5 x 8.5
10
131
64
9
5 x 15
6 x 12
7 x 10
8x9
8.5 x 8.5
12
143
393
79
10
6 x 15
7 x 13
8 x 11
9 x 10
9.5 x 9.5
12
185
411
113
12
7 x 18
8 x 16
9 x 14
10 x 12
11 x 11
12
194
655
113
12
7 x 18
8 x 16
9 x 14
10 x 12
11 x 11
14
309
680
154
14
8 x 22
9 x 19
10 x 17
11 x 15
12 x 14
13 x 13
14
321
995
154
14
8 x 22
9 x 19
10 x 17
11 x 15
12 x 14
13 x 13
16
470
1325
201
16
8 x 30
10 x 22
12 x 18
14 x 16
15 x 15
18
625
1450
201
16
8 x 30
10 x 22
12 x 18
14 x 16
15 x 15
20
684
1750
254
18
8 x 40
10 x 30
12 x 24
14 x 20
16 x 17
16.5 x 16.5
20
826
2000
254
18
8 x 40
10 x 30
12 x 24
14 x 20
16 x 17
16.5 x 16.5
22
944
2250
314
20
10 x 38
12 x 30
14 x 26
16 x 22
18 x 19
18.5 x 18.5
22
1062
2600
314
20
10 x 38
12 x 30
14 x 26
16 x 22
18 x 19
18.5 x 18.5
24
1227
2900
380
22
12 x 36
14 x 30
16 x 26
18 x 23
20 x 20
24
1369
3400
380
22
12 x 36
14 x 30
16 x 26
18 x 23
20 x 20
26
1605
3600
452
24
14 x 38
16 x 32
18 x 28
20 x 25
22 x 22
26
1699
4300
452
24
14 x 38
16 x 32
18 x 28
20 x 25
22 x 22
28
2029
5250
531
26
16 x 38
18 x 32
20 x 30
22 x 24
24 x 24
30
2478
6125
616
28
18 x 38
20 x 34
22 x 30
24 x 28
26 x 26
32
2891
6500
616
28
18 x 38
20 x 34
22 x 30
24 x 28
26 x 26
34
3068
7250
707
30
20 x 40
22 x 38
24 x 32
26 x 30
28 x 28
34
3422
7800
707
30
20 x 40
22 x 38
24 x 32
26 x 30
28 x 28
36
3681
8500
804
32
22 x 40
24 x 38
26 x 34
28 x 32
30 x 30
36
4012
9200
804
32
22 x 40
24 x 38
26 x 34
28 x 32
30 x 30
38
4342
9800
908
34
24 x 42
25 x 40
26 x 38
28 x 34
30 x 32
31 x 31
38
4625
10900
908
34
24 x 42
25 x 40
26 x 38
28 x 34
30 x 32
31 x 31
40
5144
28 x 40
30 x 36
32 x 34
33 x 33
30 x 42
32 x 38
34 x 36
35 x 35
30 x 45
34 x 40
36 x 38
37 x 37
001200MAN-05
Page 14
`
Airflow
(L/s)
02 JAN 2014
Ground Water System Information
GENERAL REQUIREMENTS
1.
Water flow to the heat pump can be controlled very accurately
by the installation of a reverse action refrigeration pressure
valve in the discharge line of the unit.
The temperature of the well water should be a minimum
of 39°F (4°C), and should normally be 45+°F (7°C)
The well system must be able to supply the required
water flow as listed under the Total Flow column in
TABLE 11.
2.
TABLE 11 - Required Flow and Air Tank Sizing
Heat
Pump
Model
Size
Heat
Pump
Flow*
USGPM
(L/s)
Home
Flow
USGPM
(L/s)
Total
Flow
USGPM
(L/s)
Minimum Air
Bladder
Tank**
USgal
(L)
25
7.0 (0.44)
4 (0.25)
11 (0.69)
22 (83)
45
10.0 (0.63)
4 (0.25)
14(0.88)
28 (106)
55
12.0 (0.76)
4 (0.25)
16(1.01)
32 (121)
65
14.0 (0.88)
4 (0.25)
18(1.14)
36 (136)
75
16.0 (1.01)
4 (0.25)
20 (1.26)
40 (151)
80
17.0 (1.07)
4 (0.25)
21(1.32)
42 (159)
Another more common method of regulating the flow is by the
use of a DOLE Valve. This valve will automatically control the
amount of water flowing through it by varying the diameter of a
flexible rubber orifice through which the water passes. This
minimizes the water usage of the unit and also prevents excessively low discharge pressure when in cooling mode. Dole
valves can be noisy, it is recommended that they be installed
outside if possible.
Optionally a water flow meter can be installed in the discharge line so that the exact amount of water flowing can be
determined at a glance. It should be placed between the Outdoor OUT (Supply OUT) pipe of the heat pump and the water
valve.
With Proper flow, there should be 5-7°F (3-4°C) delta T between the IN and OUT water temperatures of the heat pump
when operating in the heating mode.
All water line valves on both the supply and discharge lines
should be either BALL or GATE valves. GLOBE valves have a
higher pressure drop, meaning more pumping power to maintain
the required flow to the heat pump.
* These are minimum water requirements based on an
entering water temperature of 46° F.
PIPE INSULATION
**Based on two-minute well pump run time. Use next size
larger tank if there is not a match for the value indicated.
A larger tank may be used if a longer run time is desired.
All ground water piping to and from the Outdoor Loop ports
on the heat pump should be insulated with 3/8” closed cell pipe
insulation, to prevent condensation and dripping onto floors or
walls.
PLUMBING THE HEAT PUMP
The port connections for the Outdoor Loop are 1” brass
FPT fittings They are marked as OUTDOOR IN and OUT.
WATER DISCHARGE METHODS
Plumbing lines, both IN (supply) and OUT (discharge), must
be of adequate size to handle the water flow necessary for the
heat pump. A 1” copper or plastic line should be run to the Outdoor IN (Supply IN) pipe of the heat pump. Similarly, a 1”' line
should be run from the Outdoor OUT (Supply Out) pipe to the
method of disposal. P/T plugs should be installed at each port.
See Diagram A in the Ground Loop section for a description of
P/T plugs. The water valve should be installed in the OUT
(discharge) line. Refer to drawing 000907CDG at the end of
this section for the recommended setup. Placing the water
valve in the discharge line ensures that the heat exchanger inside the heat pump remains full of water when the unit is not
running. Unions or some other form of disconnect should be
used so that the coaxial heat exchanger may be accessed
should it required cleaning.
Water disposal methods vary from area to area. However,
some consideration should be made to prevent the cooled
discharge water from immediately coming in contact with the
supply source. Attempting to return the water to the source well
will eventually cool the water so much that the heat pump will
shut off on its low pressure safety control.
Acceptable methods for disposing of the waste water are
listed below. The waste water is clean, the heat pump has no
effect other than reducing the temperature of the water. Refer
to drawing 000907INF for typical disposal method diagrams.
The heat pump has an electrical connector for the water valve
just inside the case. After the water valve is installed, run the
valve harness into the case through the hole provided. Remove
the jumper plug from the Valve Connector and connect the harness in its place.
•
•
•
Second well (return well)
Percolation (Drain, ditch, leaching field)
Pond, river or stream.
ENSURE SELECTED METHOD CONFORMS TO LOCAL CODES.
Ideally there will be water flow available in excess of the
requirement of the heat pump. In such a situation the proper
pump can be selected to maintain a pressure of 30 to 40 psig.
on the lines when the heat pump is operating. However in some
cases a well can supply a heat pump only if the minimum
requirement for water is used.
02 JAN 2014
Page 15
001200MAN-05
A return well should be a minimum of 80 ft. from the supply
well for residential applications. The water returned to the well
will not necessarily be pumped into the same aquifer, depending on underground conditions. The return well must be able to
supply at least the same quantity of water as the amount you
wish to recharge into it. If the static level (level when not being
pumped) of a well is high (10 to 20 ft. from the surface) it may
be necessary to place a well cap on the well to keep the return
water from flowing out the top of the well. This cap is commonly
required since a certain amount of pressure is needed to force
the return water back down the well if the static level is high.
Water discharged by percolation will generally soak into the
ground within a distance of 50 to 100 ft. If suitable care is taken
to ensure that the drain pipe runs downhill and the end of the
pipe is protected by a bale of hay or spruce bows etc. the end of
the pipe will not freeze as the pipe will empty out when the heat
pump shuts off and the water valve closes.
001200MAN-05
When snow comes it will usually cover the entire process
much like a small spring. It is recommended that the pipe be
below the frost line when possible for maximum freeze protection.
When discharging into a river or stream, or above the surface
of a pond, the same guidelines should be followed as described
in the paragraph above for the percolation method.
When discharging the waste water below the surface of a
pond, the discharge pipe should be placed below the frost line
to prevent the pipe from freezing. As opposed to the percolation method, water will remain in the end of the pipe. It is recommended that the surface of the pond be lower than the installation location of the heat pump where practical. This reduces
the back pressure generated by the weight of the water in the
pond.
Page 16
02 JAN 2014
02 JAN 2014
Page 17
001200MAN-05
Ground Loop System Information
Once the ground loop has been pressure tested and the
header pipes have been connected to the circulator pump
module, the heat pump can be connected to the circulator pump
module.
The port connections for the Outdoor Loop are 1” brass
FPT fittings. They are marked as OUTDOOR IN and OUT.
CIRCULATOR PUMP MODULE
Maritime Geothermal Ltd. has compact pump modules with
built in three way valves to facilitate filling and purging the
ground loop. Refer to drawing 000906CDG at the end of this
section. Alternatively, Grundfoss® Model UPS 26-99 or Taco®
Model 0011 pumps or other brands with similar pumping
capability may be used. The single pump module will typically
handle systems up to 3 tons (model sizes 25, 35, and 45); the
two pump module will typically handle 4 to 6 ton systems (model
sizes 55, 65, 75, 80). This is based on a typical parallel system
with one circuit per ton.
Maritime Geothermal recommends calculating the total
pressure drop of the ground loop (including headers, indoor
piping and heat pump exchanger drop) based on the antifreeze
type and concentration at the desired minimum loop
temperature. A pump module that can deliver the flow required
for the unit at the calculated total pressure drop should be
selected. Refer to the Model Specific Information section for
unit flow requirements.
The P/T plug will allow the installer or homeowner to check
water flow through the loop by measuring the pressure
difference through the heat exchanger and comparing it to that
listed in the Model Specific Information section, or the
specifications document. Optional fittings with P/T ports are
available for the circulator pump modules sold by Maritime
Geothermal Ltd..
FLUSHING & PURGING THE GROUND
LOOP
Once the groundloop has been installed and all connections
are completed between the heat pump, circulator pump module
and ground loop, the entire ground loop system should be
pressure tested with air to 100 PSIG to make sure there are
no leaks on any of the inside fittings. Soap all joints and observe
that the pressure remains constant for 1 hour.
When satisfied that all connections are leak free, release the
air pressure and connect a purge cart (see Diagram B ) to the
flushing access ports at the pump module (refer to drawing
000906CDG). A temporary flushing system can alternately be
constructed using a 45 gal. barrel and a pump with sufficient
volume and head capability to circulate fluid at a velocity of at
least 2 ft./min. through all parts of the loop.
DIAGRAM B - Typical Purge Cart
Loop pressure drops can be calculated using software such
as those mentioned in the Horizontal Ground loops section, or
can be calculated in a spreadsheet using the pipe
manufacturer’s pressure drop tables for pipe diameter and
fittings.
The circulator pump module must be connected to the heat
pump Outdoor Loop ports with a lineset suitable for the flow
required with minimum pressure drop. 1” rubber or plastic lines
should be used. The installation of P/T plugs (pressure /
temperature, pronounced “Pete’s plugs” ) is recommended on
both the entering and leaving lines at the heat pump (see
Diagram A).
DIAGRAM A - Typical P/T (Pete’s) Plug
& Thermometer Stems
Adjust the circulator pump module valves to connect the
purge cart to the ground loop. Begin pumping water through the
ground loop, ensuring that the intake of the pump stays
submerged at all times by continuously adding water. Water
flowing back from the return line should be directed below the
water level in the barrel or flush tank to prevent air being mixed
with the outgoing water.
001200MAN-05
Page 18
02 JAN 2014
Once the lines have been filled and no more air bubbles are
appearing in the line, adjust the circulator pump module valves
to circulate water through the heat pump using the same
technique as described above. When all air is removed reverse
the flow of water through the lines by interchanging the flush
cart lines and purge again. You will be able to visibly tell when
all air is removed.
TABLE 13 - Volume of fluid per 100 ft. of pipe
Volume /100ft.
Type of Pipe
Diameter
Igal
USgal
L
Copper
1”
3.4
4.1
15.5
ADDING ANTIFREEZE SOLUTION
1-1/4”
5.3
6.4
24.2
In most mid and northern areas of the US and in all of
Canada it is necessary to condition the loop fluid by the addition
of some type of antifreeze solution so that it will not freeze
during operation in the winter months. This antifreeze is required
because the loop fluid will normally reach a low entering
temperature of 28°F to 32°F (-2°C to 0°C) and refrigerant
temperatures inside the heat pump’s heat exchanger may be as
low as 20°F (11°C) cooler. See TABLE 12 for details of freeze
protection provided by different concentrations.
1-1/2”
7.7
9.2
34.8
Rubber Hose
1”
3.2
3.9
14.8
Polyethylene
3/4” IPS SDR11
2.3
2.8
10.6
1” IPS SDR11
3.7
4.5
17.0
1-1/4” IPS SDR11
6.7
8.0
30.3
1-1/2” IPS SDR11
9.1
10.9
41.3
2” IPS SDR11
15.0
18.0
68.1
1.5
5.7
TABLE 12 - Antifreeze Percentages
Other Item Volumes
BY VOLUME
Protection to:
10°F
15°F
20°F
25°F
Heat Exchanger
Average
Methanol
25%
21%
16%
10%
Purge Cart Tank
See cart manual
Propylene Glycol
38%
30%
22%
15%
Methanol
Propylene Glycol
!
10°F
15°F
20°F
25°F
16.8%
13.6%
10%
6.3%
30%
23.5%
18.3%
12.9%
INITIAL PRESSURIZATION
WARNING: Add enough antifreeze to allow for a
temperature 20°F (11°C) lower than the expected
lowest loop fluid temperature entering the heat pump.
Insufficient antifreeze concentration could cause the
heat exchanger to freeze and rupture, voiding the
warranty.
Although many different antifreeze solutions have been
employed in geothermal systems, the alcohols such as
methanol or ethanol have the most desirable characteristics for
groundloop applications. The overall heat transfer
characteristics of these fluids remain high although care must be
taken when handling pure alcohols since they are extremely
flammable. Once mixed in a typical 25% by volume ratio with
water the solution is not flammable. In situations where alcohols
are not allowed as a loop fluid due to local regulations then
propylene glycol is a non-toxic alternative which can be
substituted . Propylene glycol should only be used in cases
where alcohols are not permitted since the heat transfer
characteristics are less desirable and it becomes more viscous
at low temperatures, increasing pumping power.
The volume of fluid that your loop system holds can be
closely estimated by totaling the number of ft. of each size pipe
in the system and referencing TABLE 13 the for approximate
volume per 100 ft.
When the volume of the loop has been calculated and the
appropriate amount of antifreeze is ready for addition by
referencing TABLE 12 , drain the equivalent amount of water
from the flush cart or mixing barrel and replace it with the
antifreeze.
02 JAN 2014
TBD
When using alcohols, be sure to inject below the water
line to reduce initial volatility of the pure antifreeze. If the
loop is large it may be necessary to refill the tank with antifreeze
several times to get all the antifreeze into the loop. Pump the
loop for 5 to 10 minutes longer to ensure the remaining fluid has
been well mixed.
BY WEIGHT
Protection to:
1.2
At this point open all valves in the flow circuit and slowly close
off the supply and return flush cart valves in a manner that
leaves about 20-30 psig. on the system. If an air bladder
expansion tank is used it should be charged to the above
pressure before actual water pressure is put on the system .
Systems without an expansion tank will experience greater
fluctuations in pressure between the heating and cooling
seasons, causing pressure gauges to have different values as
the loop temperature changes. This fluctuation is normal since
expansion and contraction of the loop fluid must be handled by
the elasticity of the plastic loop.
• Pressurize the loop to a static pressure of 45 psig. when
installing a system in the fall going into the heating season.
• Pressurize the loop to a static pressure of 25 psig. when
installing a system in the spring or summer going into the
cooling season.
After operating the heat pump for a period of time, any
residual air in the system should be bled off and the static
pressure should be verified and adjusted if necessary. Add
additional water / antifreeze mix with the purge cart to bring the
pressure back to the original setting if required.
PIPE INSULATION
All ground loop piping inside the structure (between the
structure entry point and the heat pump) should be insulated
with 3/8” thick closed cell pipe insulation to prevent
condensation and dripping onto floors or walls.
Page 19
001200MAN-05
001200MAN-05
Page 20
02 JAN 2014
Startup Procedure
The following steps describe how to perform the startup procedure of the geothermal heat pump.
The R-Series Two-Stage R410a Startup Record located in this manual is used in conjunction with this startup procedure to provide a detailed record of the installation. A completed copy should be left on site, a copy kept on file by the installer and a copy should
be sent to Maritime Geothermal Ltd.
Check the boxes or fill in the data as each step is completed. For data boxes, circle the appropriate units. Fill in the top section of all
three copies, or one copy if photocopies can be made after the startup has been completed.
PRE-START INSPECTION
Ductwork:
1. Verify that all ductwork has been completed and is firmly attached to the unit. Verify that any dampers or diverters are
properly set for operation of the heat pump.
2. Verify that all registers are open and clear of any objects that would restrict the airflow.
3. Verify that a new air filter is installed and the cover is secured.
4. Verify the condensate drain is connected, properly vented and free of debris.
5. If a plenum heater has been installed, verify that it is securely fastened to the ductwork.
Outdoor Loop (Ground Loop):
1. Verify that all shutoff valves are fully open and there are no restrictions in the piping from the heat pump to the ground loop,
and that full flow is available to the heat pump.
2. Verify that the entire system has been flooded and all the air has been purged as much as possible. Further purging may
be required after the system has been operating for a while.
3. Verify that the loop contains the proper mix of antifreeze for the intended application. Record the type of antifreeze and the
mixture value on the startup sheet; circle % Vol. or % Weight.
4. Record the static loop pressure on the startup sheet.
Outdoor Loop (Ground Water):
1. Verify there are no leaks in the connections to the unit. Verify the water valve is installed and properly oriented in the
return line.
2. Verify that there is flow control in the return line.
Domestic Hot Water (if equipped):
1. Verify that all shutoff valves are fully open and there are no restrictions in the piping from the heat pump to the domestic
hot water tank.
2. Verify that the entire system has been flooded and all the air has been purged as much as possible. Further purging may
be required after the system has been operating for a while.
3. Verify that the brown wire with the insulated terminal is disconnected in the electrical box. Refer to the schematic diagram
for more information.
Electrical:
1. Ensure the power to the unit is off. Ensure the power to the plenum heater is off if equipped.
2. Verify all high voltage connections. Ensure that there are no stray wire strands, all connections are tight and the ground
wire is connected tightly to the ground connector for the heat pump and plenum heater.
3. Record the fuse / circuit breaker size and wire gauge for the heat pump. Record the fuse / circuit breaker size, wire gauge
and size of the plenum heater if installed.
4. Verify that the control connections to the thermostat and plenum heater (if installed) are properly connected and all control
signals are off, so that the unit will not start up when the power is turned on.
5. Ensure all access panels except the lower one that provides access to the electrical box are in place.
02 JAN 2014
Page 21
001200MAN-05
UNIT STARTUP
The unit is now ready to be started. The steps below outline the procedure for starting the unit and verifying proper operation of
the unit. It is recommended that safety glasses be worn during the following procedures.
Preparation:
1. Remove the caps from the service ports and connect a refrigeration manifold set to the unit.
2. Turn the power on to the heat pump and set the thermostat to OFF. Set up the thermostat as per the instructions provided
with it so that it will function properly with the heat pump system (set for heat pump, not for heating and cooling). The O
signal should be set to active in cooling mode.
3. Measure the following voltages on the compressor contactor and record them on the startup sheet: L1-L2, L2-L3, L1-L3.
Heating Mode:
1. Set the thermostat to heating mode and adjust the setpoint to activate Stage 1 and Stage 2. The fan should slowly ramp up
to speed after the time delay of the thermostat expires (if applicable) and the compressor will start (allow 30-60 seconds for
the water valve to open for ground water systems)
2. Check the refrigeration gauges. The suction and discharge pressures will depend on the loop temperatures, but they should
be about 90-110PSIG and 260-360PSIG respectively for a typical start-up.
3. Monitoring the refrigeration gauges while the unit runs. Record the following after 10 minutes of runtime:
1. Suction pressure
2. Discharge pressure
3. Duct Return temperature (poke a small hole in the flex collar and insert probe in airstream)
4. Duct Supply temperature (poke a small hole in the flex collar and insert probe in airstream)
5. Duct Delta T (should be between 22-32°F, 12-18°C)
6. Outdoor Loop In (Supply In) temperature
7. Outdoor Loop Out (Supply Out) temperature
8. Outdoor Delta T (should be between 5-8°F, 3-4°C)
9. Outdoor flow (if available)
10. Compressor L1(C) current (black wire, place meter between electrical box and compressor)
4. Adjust the thermostat setpoint to the desired room temperature and let the unit run through a cycle. Record the setpoint,
Suction, and discharge pressures when the unit shuts off.
5. For units with a desuperheater, turn the power off to the unit. Connect the brown wire with the blue insulated terminal to the
compressor contactor as shown in the electrical box diagram. Turn the DHW Switch in the unit post on. Turn the power to the
unit on.
6. Remove the electrical cover from the plenum heater. Place a current clamp meter around one of the supply wires. Turn on
the power to the plenum heater. Adjust the thermostat setpoint to 85°F (29°C). Verify that the current draw increase as
each stage is activated. (10kW has 2 stages, 15kW has 3 stages and 20kW has 4 stages).
7. Verify the DHW IN and DHW OUT temperatures (if applicable) by hand (caution: pipes get hot). If the DHW OUT line does
not become hotter than the DHW IN line the circulator is air locked. Bleed the air from the system and check the
temperature differential again to ensure there is flow from the circulator.
Cooling Mode:
1. Set the thermostat to cooling mode and adjust the setpoint to activate Stage 1 and Stage 2.
2. Monitoring the refrigeration gauges while the unit runs. Record the following after 10 minutes of runtime:
1. Suction pressure
2. Discharge pressure
3. Duct Return temperature
4. Duct Supply Out temperature
5. Duct Delta T
6. Outdoor Loop In (Supply In) temperature
7. Outdoor Loop Out (Supply Out) temperature
8. Outdoor Delta T
3. Adjust the thermostat setpoint to the desired room temperature if possible, otherwise set it just low enough to allow the unit
to run (ie 1°F (0.5°C) less than room temperature) and let the unit run through a cycle. Record the thermostat setpoint,
suction pressure and discharge pressure when the unit shuts off.
Final Inspection:
1. Turn the power off to the unit (and plenum heater if installed) and remove all test equipment.
2. Install the electrical box cover and the access panel on the heat pump. Install the service port caps securely to prevent
refrigerant loss. Install the electrical cover on the plenum heater if applicable.
3. Do a final check for leaks in the ground water / ground loop system and ensure the area is clean.
4. Turn the power on to the unit and the plenum heater if installed. Set the thermostat to the final settings.
Startup Record:
1. The installer shall sign and date the Startup Record and have the homeowner sign as well. The installer shall leave the Startup
Record with the homeowner, retain a copy for filing and send a copy to Maritime Geothermal Ltd. for warranty registration.
001200MAN-05
Page 22
02 JAN 2014
Startup Record —R-Series Size 25-80 Two-Stage R410a
Installation Site
Startup Date
Installer
City
Company
Province
Model
Country
Serial #
Homeowner Name
Homeowner Phone #
Check boxes unless asked to record data. Circle data units.
PRE-START INSPECTION
Ductwork
Ductwork is completed, dampers/ diverters are adjusted
Registers are open and clear of objects
Air filter and end cap are installed
Condensate Drain is connected, properly vented and free of debris
Plenum heater is securely fastened (if applicable)
Ground Loop
System
All shut-off valve are open (full flow available)
Loop is full and purged of air
Antifreeze type
Antifreeze concentration
% Volume
Loop static pressure
PSI
Ground Water
Water Valve installed in return line
System
Flow control installed in return line
Domestic Hot
All shut-off valves are open
Water
Lines are full and purged
% Weight
kPa
Desuperheater pump wire is disconnected
Electrical
High voltage connections are correct and securely fastened
Circuit breaker (or fuse) size and wire gauge for Heat Pump
A
Ga.
Circuit breaker (or fuse) size, wire gauge, and Plenum Heater size
A
Ga.
kW
Low voltage connections are correct and securely fastened
STARTUP DATA
Preparation
Voltage across L1 and L2, L1 and L3, L2 and L3
Heating Mode
Suction Pressure / Discharge Pressure
(10 minutes)
Duct Return, Duct Supply, and Delta T
In
Out
°F
°C
Outdoor In (Supply In), Outdoor Out (Supply Out), and Delta T
In
Out
°F
°C
Outdoor Flow
Igpm
Compressor L1 (black wire) current
A
psig
kPa
VAC
psig
USgpm
kPa
L/s
Domestic Hot Water functioning
Thermostat setpoint, suction and discharge pressures at cycle end
°F
°C
Cooling Mode
Suction Pressure / Discharge Pressure
(10 minutes)
Duct Return, Indoor Out, and Delta T
In
Out
°F
°C
Outdoor In (Supply In), Outdoor Out (Supply Out), and Delta T
In
Out
°F
°C
Thermostat setpoint, suction and discharge pressures at cycle end
°F
psig
kPa
Date:
psig
Installer Signature:
°C
kPa
Homeowner Signature:
A total of three copies are required, one for the homeowner, one for the installer and on to be sent to Maritime Geothermal Ltd.
02 JAN 2014
Page 23
001200MAN-05
General Maintenance
GENERAL MAINTENANCE SCHEDULE
Item
Interval
Procedure
Air Filter
6 months
Inspect for dirt. Replace if necessary.
Contactor
1 year
Inspect for pitted or burned points. Replace if necessary.
Condensate Drain
1 year
Inspect for clogs. Remove and clean if necessary.
Heat exchanger
As required*
Clean as per HEAT EXHCANGER FLUSING PROCEDURE below.
*Generally not required for closed loop systems. Whenever system performance is reduced for open loop.
COAXIAL HEAT EXCHANGER FLUSHING PROCEDURE—GROUNDWATER
STEP 1
Isolate the heat exchanger by closing the valves in the IN and OUT ports to the heat exchanger.
STEP 2
Blow out the heat exchanger into a clean 5 gallon bucket using compressed air.
STEP 3
If a purge cart is not available, use a 5 gallon plastic bucket, a circulator and some plastic piping to create a
makeshift pump system. Connect a the inlet and outlet to the heat exchanger ports.*
STEP 4
Place 2 gallons of RYDLYME in the purge cart (or bucket). Circulate the fluid through the heat exchanger
for at least 2 hours (3 recommended).
STEP 5
Disconnect the purge system dispose of the solution. RYDLYME is non-toxic and biodegradable and as
such can be poured down a drain.
STEP 6
Connect fresh water and a drain to the heat exchanger ports and flush the exchanger for several minutes.
STEP 7
Return the plumbing to its original configuration and open the IN and OUT valves. Operate the system and
check for improved performance.
*Depending on the plumbing, there should be either unions or boiler drains for to access the heat exchanger.
COAXIAL HEAT EXCHANGER FLUSHING PROCEDURE—GROUND LOOP
STEP 1
Isolate the heat exchanger by placing the pump module valves in the exchanger flushing position.
STEP 2
Connect a compressed air and a drain pipe to the pump module purge ports and blow the anti-freeze solution into a clean 5 gallon bucket.
STEP 3
Connect a purge cart to the pump module purge ports.
STEP 4
Place 2 gallons of RYDLYME in the purge cart. Circulate the fluid through the heat exchanger for at least 2
hours (3 recommended).
STEP 5
Disconnect the purge cart and dispose of the solution. RYDLYME is non-toxic and biodegradable and as
such can be poured down a drain. Clean the purge cart thoroughly.
STEP 6
Connect fresh water and a drain to the pump module purge ports and flush the exchanger for several
minutes.
STEP 7
Blow the heat exchanger out with compressed air as per STEP 2 and dump the water down a drain.
STEP 8
Connect the purge cart to the pump module purge ports. Re-fill and purge the heat exchanger with as per
standard procedures (the anti-freeze from STEP 2 can be re-used).
STEP 9
Disconnect the purge cart and set the pump module valves back to the original positions.
STEP 10
Operate the system and check for improved performance.
*Depending on the plumbing, there should be either unions or boiler drains for to access the heat exchanger.
001200MAN-05
Page 24
02 JAN 2014
Troubleshooting Guide
The following steps are for troubleshooting the geothermal heat pump. If the problem is with the domestic hot water or the
plenum heater, proceed to those sections at the end of the troubleshooting guide. Repair procedures and reference refrigeration circuit diagrams can be found at the end of the troubleshooting guide.
STEP 1: Verify that the display is present on the thermostat. If it is not, proceed to POWER SUPPLY TROUBLE
SHOOTING, otherwise proceed to STEP 2.
STEP 2: Remove the door and electrical box cover and check to see if there is a fault code on the control board. If
there is, record the fault code. Turn the power off, wait 10 seconds and turn the power back on. Set the
thermostat to call for heating or cooling depending on the season.
STEP 3: If a 24VAC signal does not appear across Y1 and C of the terminal strip within 6 minutes, proceed to the
THERMOSTAT TROUBLESHOOTING section, otherwise proceed to STEP 4.
STEP 4: If a fault code appears once a signal is present at Y1 and the compressor does not attempt to start,
proceed to the FAULT CODE TROUBLESHOOTING section, otherwise proceed to STEP 5.
STEP 5: If no fault codes appear and the compressor does not attempt to start, attempts to start but cannot, starts hard, or starts
but does not sound normal, proceed to the COMPRESSOR TROUBLESHOOTING section, otherwise proceed to
STEP 6.
STEP 6: If the compressor starts and sounds normal, this means the compressor is OK and the problem lies
elsewhere. Proceed to the OPERATION TROUBLESHOOTING section.
NOTE: To speed up the troubleshooting process, the Test Jumper on the safety board can be placed to the YES position to change
the anti-short cycle timer to 5 seconds. Be sure to set it back to NO when servicing is complete.
POWER SUPPLY TROUBLESHOOTING
Fault
No power to the
heat pump
No display on
thermostat.
02 JAN 2014
Possible Cause
Verification
Recommended Action
Disconnect switch open
(if installed)
Verify disconnect switch is in the
ON position.
Fuse blown /
Breaker Tripped.
At heat pump disconnect box,
Reset breaker or replace fuse
voltmeter shows 230VAC on the with proper size and type. (Timeline side but not on the load side. delay type “D”)
Transformer breaker
tripped.
Breaker on transformer is sticking Push breaker back in. If it trips
out.
again locate cause of short circuit
and correct.
Faulty transformer
Transformer breaker is not
Replace transformer.
tripped, 230VAC is present
across L1 and L3 of the compressor contactor but 24VAC is not
present across RH and C of the
terminal strip.
Faulty wiring between
heat pump and thermostat.
24VAC is not present across C
and R(RH) of the thermostat.
Faulty Thermostat.
24VAC is present across C and R Replace thermostat.
(RH) of the thermostat but thermostat has no display.
Page 25
Determine why the disconnect
switch was opened, if all is OK
close the switch.
Correct the wiring.
001200MAN-05
THERMOSTAT TROUBLESHOOTING
Fault
No Y1 signal to
heat pump
(after 6 minutes)
Possible Cause
Verification
Recommended Action
Incorrect thermostat setup.
Thermostat does not indicate a call Correct the setup.
for heat. No 24VAC signal present
across C and Stage 1 of the thermostat
Faulty thermostat to heat
pump wiring.
24VAC signal present across Stage
1 and C of the thermostat but not
present across Y1 and C of the terminal strip.
Faulty thermostat.
No 24VAC between Stage 1 and C Replace thermostat.
of the thermostat when a call is indicated on the thermostat.
Correct or replace wiring
FAULT CODE TROUBLESHOOTING
Fault
Fault Code 1
(High Pressure
Control)
Fault Code 2
(Low Pressure
Control)
Fault Code 3
(Flow Switch)
001200MAN-05
Possible Cause
Verification
Recommended Action
Faulty High Pressure Con- Verify if there is 24VAC across HP1
trol (open).
on the control board and C of the ter* Must be a signal present minal strip, as well as HP2 and C.
on Y1 for this test.
*HP pressures must be at
static levels.
Replace high pressure control if
voltage is present on HP1 but not
on HP2.
Faulty control board.
Replace control board.
24VAC is present across HP1 and
C1, and HP2 and C, but no voltage
is present across CC on the control
board and C.
Faulty Low pressure con- Verify if there is 24VAC across LP1
trol (open).
on the control board and C of the ter* Must be a signal present minal strip, as well as LP2 and C.
on Y1 for this test.
*HP pressures must be at
static levels.
Replace high pressure control if
voltage is present on LP1 but not
on LP1.
Faulty control board.
24VAC is present across LP1 and C, Replace control board.
and LP2 and C, but no voltage is
present across CC on the control
board and C.
Unit out of refrigerant.
Check static refrigeration pressure
of the unit for a very low value.
Locate the leak and repair it.
Spray nine, a sniffer and dye are
common methods of locating a
leak.
Flow switch jumper removed or faulty.
Verify jumper is in place between
pins marked FLOW SWITCH.
Place a jumper if missing.
Flow switch faulty.
(Only if installed)
Verify 24VAC is present between
each flow switch pin on the control
board and the C terminal of the terminal strip while there is flow
through the unit.
Replace flow switch if signal is
not present at both terminals on
the control board.
Faulty control board.
24VAC is present across each
FLOW SWITCH terminal and C, but
not voltage is present across CC on
the control board and C.
Replace control board.
Page 26
02 JAN 2014
COMPRESSOR TROUBLESHOOTING
Fault
Compressor will
not start
Compressor
starts hard
Compressor
Stage 2 will not
activate
02 JAN 2014
Possible Cause
Verification
Recommended Action
Faulty control board.
Measuring from C on the terminal
strip, verify there is voltage at Y,
HP1, HP2, LP1, LP2, and both flow
pins but no voltage present at CC.
Replace control board.
Faulty run capacitor.
(Single phase only)
Check value with capacitance meter. Replace if faulty.
Should match label on capacitor.
Compressor will hum while trying to
start and then trip its overload.
Loose or faulty wiring.
Check all compressor wiring, includ- Fix any loose connections. Reing inside compressor electrical box. place any damaged wires.
Faulty compressor
contactor.
Voltage on line side with contactor
Replace contactor.
held closed, but no voltage on one
or both terminals on the load side.
Points pitted or burned.
Or, 24VAC across coil but contactor
will not engage.
Thermal overload on
compressor tripped.
Ohmmeter shows reading when
Proceed to Operation Troubleplaced across R and S terminals
shooting to determine the cause
and infinity between C & R or C & S. of the thermal overload trip.
A valid resistance reading is present
again after the compressor has
cooled down.
Burned out motor
(open winding)
Remove wires from compressor.
Replace the compressor.
Ohmmeter shows infinite resistance
between any two terminals Note: Be
sure compressor overload has had a
chance to reset. If compressor is hot
this may take several hours.
Burned out motor
(shorted windings)
Remove wires from compressor.
Resistance between any two terminals is below the specified value.
Replace the compressor.
Motor shorted to ground.
Remove wires from compressor.
Check for infinite resistance between each terminal and ground.
If any terminal to ground is not
infinite replace the compressor.
Seized compressor due to Compressor attempts to start but
locked or damaged
trips its internal overload after a few
mechanism.
seconds. (Run capacitor already
verified)
Attempt to “rock” compressor free.
If normal operation cannot be
established, replace compressor.
Start capacitor faulty.
(Single phase only)
Check with capacitance meter.
Check for black residue around
blowout hole on top of capacitor.
Replace if faulty.
Remove black residue in electrical
box if any.
Potential Relay faulty.
(Single phase only)
Replace with new one and verify
compressor starts properly.
Replace if faulty.
Compressor is “tight” due
to damaged mechanism
Compressor attempts to start but
trips its internal overload after a few
seconds. Run capacitor has been
verified already.
Attempt to “rock” compressor free.
If normal operation cannot be established, replace compressor.
Faulty Stage 2 module
Verify if 24VAC is present across
Y2 and C of the terminal strip.
Replace module if signal is present. Check wiring if signal is not
present.
Page 27
001200MAN-05
OPERATION TROUBLESHOOTING - HEATING MODE
Fault
High Discharge
Pressure
Possible Cause
Verification
Recommended Action
Air Flow
See Fan Troubleshooting section
Correct the problem.
TXV adjusted too far
closed.
Verify superheat. It should be beAdjust TXV to obtain 8-12°F
tween 8-12°F (3-6°C). Superheat will (3-6°C) superheat.
be high if TXV is closed too far.
TXV stuck almost closed Adjusting the TXV does not affect the Adjust the TXV all the way in and
or partially blocked by for- superheat or the suction pressure.
out a few times to loosen it. Reeign object.
place TXV if this does not work.
Low Suction
Pressure
Filter-drier plugged
Feel each end of the filter- drier, it
Replace filter-drier.
should be the same temperature. If
there is a temperature difference then
it is plugged. Also causes low suction pressure.
Unit is overcharged.
(Only possible if unit has
been opened in the field
and incorrectly charged).
High sub-cooling, low delta T across
air coil.
Remove 1/2lb of refrigerant at a
time and verify that the discharge
pressure reduces.
Low or no Outdoor liquid
flow
Delta T across the Outdoor Loop
ports should be between 5-7°F
(3-4°C), or compare pressure drop to
the tables for the unit.
Determine the cause of the flow
restriction and correct it.
Verify pumps are working and
sized correctly for ground loop
systems.
Verify well pump and water valve
is working for ground water systems.
Entering liquid temperature too cold.
Measure the entering liquid tempera- Increase the size of the ground
ture. Most likely caused by underloop.
sized ground loop.
Dirty or fouled coaxial
Disconnect the water lines and
heat exchanger.
check the inside of the pipes for
(typically for ground water, scale deposits.
unlikely for ground loop)
Have a qualified service technician backflush the coaxial exchanger.
Return air too cold
Restrict air flow temporarily until
room comes up to temperature.
Measure return air temperature.
Should be above 60°F (15°C).
TXV stuck almost closed Adjusting the TXV does not affect the Adjust the TXV all the way in and
or partially blocked by for- superheat or the suction pressure.
out a few times to loosen it. Reeign object.
TXV may be frosting up.
place TXV if this does not work.
001200MAN-05
Low refrigerant charge.
Entering liquid temperature, flow and
entering air temperature are good but
suction is low. Check static refrigeration pressure of the unit for a very
low value.
Locate the leak and repair it.
Spray nine, a sniffer and dye are
common methods of locating a
leak.
Faulty compressor, not
pumping.
Pressures change only slightly from
static values when compressor is
started.
Replace compressor.
Page 28
02 JAN 2014
OPERATION TROUBLESHOOTING - HEATING MODE
Fault
High Suction
Pressure
(may appear to
not be pumping)
Possible Cause
Verification
Recommended Action
Leaking reversing valve.
Reversing valve is the same temper- Replace reversing valve.
ature on both ends of body, common suction line is warm, compressor is running hot.
TXV adjusted too far
open.
Verify superheat. It should be between 8-12°F (3-6°C). Superheat
will be low if TXV is open too far.
TXV stuck open.
Adjust the TXV all the way in and out
Adjusting the TXV does not affect
a few times to loosen it. Replace
the superheat or the suction pressure. Low super heat and discharge TXV if this does not work.
pressure.
Adjust TXV to obtain 8-12°F
(3-6°C) superheat.
Compressor
frosting up
See Low Suction
Pressure in this section.
TXV frosting up
TXV stuck almost closed Adjusting the TXV does not affect
or partially blocked by for- the superheat or the suction preseign object.
sure.
Attempt to adjust the TXV all the
way out and all the way in a few
times to loosen it. Replace TXV
if this does not work.
Random high
pressure trip
(does not occur
while on site)
Faulty compressor contac- Points pitted or burned. Contactor
tor.
sometimes sticks causing the compressor to run without the fan, tripping the high pressure control.
Replace contactor.
Intermittent fan.
Correct the problem.
See Fan Troubleshooting section.
OPERATION TROUBLESHOOTING - COOLING MODE
Fault
Heating instead
of cooling
High Discharge
pressure
Possible Cause
Verification
Thermostat not set up
properly.
Verify that there is 24VAC across
O/B/W1 and C of the terminal strip
when calling for cooling.
Correct thermostat setup.
Change to a different thermostat.
Faulty reversing valve solenoid coil.
Verify solenoid by removing it from
the shaft while the unit is running.
There should be a loud “whoosh”
sound when it is removed.
Replace solenoid if faulty.
Faulty reversing valve.
A click can be heard when the coil
is energized but the unit continues
to heat instead of cool.
Replace reversing valve.
Low or no Outdoor liquid
flow
Delta T across the Outdoor Loop
ports should be between 8-12°F
(4-7°C), or compare pressure drop
to the tables for the unit.
Determine the cause of the flow
restriction and correct it.
Verify pumps are working for
ground loop systems. Verify well
pump and water valve is working
for ground water systems.
Entering liquid temperature too warm.
Most likely caused by undersized
ground loop.
Verify the ground loop sizing. Increase the size of the ground loop
if undersized.
Dirty or fouled coaxial
Disconnect the water lines and
heat exchanger.
check the inside of the pipes for
(typically for ground water, scale deposits.
unlikely for ground loop)
02 JAN 2014
Recommended Action
Page 29
Have a qualified service technician
backflush the coaxial exchanger.
001200MAN-05
OPERATION TROUBLESHOOTING - COOLING MODE
Fault
Possible Cause
Verification
Recommended Action
High Discharge
pressure
Unit is overcharged.
(Only possible if unit has
been opened in the field
and incorrectly charged).
High sub-cooling, low delta T
across water coil.
Remove 1/2lb of refrigerant at a
time and verify that the discharge
pressure reduces.
High Suction
Pressure
(may appear to
not be pumping)
TXV adjusted too far
open.
Verify superheat. It should be between 8-12°F (3-6°C). Superheat
will be low if TXV is open too far.
Adjust TXV to obtain 8-12°F
(3-6°C) superheat.
TXV stuck open.
Adjusting the TXV does not affect
the superheat or the suction pressure. Low super heat and discharge pressure.
Adjust the TXV all the way in and out a
few times to loosen it. Replace TXV if
this does not work.
Leaking reversing valve.
Reversing valve is the same temReplace reversing valve.
perature on both ends of body,
common suction line is warm, compressor is running hot.
Air Flow
See Fan Troubleshooting section.
Note: low airflow will cause the air
coil to ice up once the suction
drops below 90PSIG.
Low Suction
Pressure
Correct the problem.
TXV stuck almost closed Adjusting the TXV does not affect
or partially blocked by for- the superheat or the suction preseign object.
sure. TXV may be frosting up.
Adjust the TXV all the way in and
out a few times to loosen it. Replace TXV if this does not work.
Low or no refrigerant
charge.
Entering air temperature and airflow are good but suction is low.
Check static refrigeration pressure
of unit for very low value.
Locate the leak and repair it.
Spray nine, a sniffer and dye are
common methods of locating a
leak.
Faulty compressor, not
pumping.
Pressures change only slightly from Replace compressor.
static values when compressor is
started.
Compressor
frosting up
See Low Suction
Pressure in this section.
TXV frosting up
TXV stuck almost closed Adjusting the TXV does not affect
or partially blocked by for- the superheat or the suction preseign object.
sure.
Random Low
Pressure trip
(does not occur
while there)
Faulty compressor
contactor.
Points pitted or burned. Contactor Replace contactor.
sometimes sticks causing the compressor to run without the fan, tripping the low pressure control.
Intermittent fan.
See Fan Troubleshooting section.
001200MAN-05
Page 30
Adjust the TXV all the way in and out a
few times to loosen it. Replace TXV if
this does not work.
Correct the problem.
02 JAN 2014
FAN TROUBLESHOOTING
Fault
Low Airflow
Possible Cause
Verification
Dirty air filter
Inspect.
Replace.
Dirty air coil.
Inspect.
Clean.
Poor Ductwork
Measure delta T between supply
and return ducts at the unit, it in
heating mode, it should not be
above 30°F(17°C).
The ECM fan will provide proper
airflow up to 0.5 inH2o for 1/2HP
motors and 0.7 inH2o for 1HP
motors. The ductwork is poorly
designed or greatly undersized if
the fan motor cannot provide the
required airflow.
Air flow selected on Tap
Board is too low.
Check selection on Air Flow Tap
Board.
Select a higher setting.
Air flow reduction is enabled.
AR1 and AR2 are connected with a
dry contact.
Air flow reduction may not be feasible with poor ductwork, and/or
lower Air Flow selections. Increase settings until unit operates
properly.
Fan operating on Fan Control Signal Harness is loose.
wrong Stage
speed
Verify that the connector is properly Repair any loose connections.
inserted into the fan motor. Gently
tug on each wire to verify it is
properly inserted into the connector.
Faulty Control Signal Har- Measure 24VAC between White (pin
ness or faulty motor head. 3) and the following at the fan control signal harness (insert probes in
Ensure signal is present connector where wire is inserted, do
not unplug the connector):
on terminal strip.
Circulation = Grey (pin 15)
Stage 1 = Yellow (pin 6)
Stage 2=Yellow/Black (pin14)
Stage 3 = Violet (pin 2)
Fan not operating or operating
intermittently
Fan Control Signal Harness and/or Fan Power
Harness is loose.
Faulty Fan Power Harness or faulty motor.
If proper signal isn’t present, replace Fan Control Signal Harness. If proper signal is present,
replace fan motor head.
Verify that the connector is properly Repair any loose connections.
inserted into the fan motor. Gently
tug on each wire to verify it is
properly inserted into the connector.
Faulty Control Signal Har- Measure 24VAC between White (pin
ness or faulty motor head. 3) and the following at the fan control signal harness (insert probes in
Ensure signal is present connector where wire is inserted, do
not unplug the connector):
on terminal strip.
Circulation = Grey (pin 15)
Stage 1 = Yellow (pin 6)
Stage 2=Yellow/Black (pin14)
Stage 3 = Violet (pin 2)
02 JAN 2014
Recommended Action
If proper signal isn’t present, replace Fan Control Signal Harness. If proper signal is present,
replace fan motor head.
Insert the tips of the voltmeter
Replace Power Harness if
probes into the back of the connect- 230VAC is not present, replace
or at the fan to measure the voltage motor if 230VAC is present
across the red and black wires, value should be 230VAC
Page 31
001200MAN-05
PLENUM HEATER TROUBLE SHOOTING
Fault
No 230VAC
across plenum
heater L1 and L2
Possible Cause
Verification
Recommended Action
Disconnect switch open.
(if installed)
Verify disconnect switch is in the ON
position.
Determine why the disconnect
switch was opened, if all is OK
close the switch.
Fuse blown /
Breaker Tripped.
At plenum heater disconnect box (if
installed), voltmeter shows voltage on
the line side but not on the load side.
Check if breaker is tripped.
Reset breaker or replace fuse at
plenum heater disconnect box.
Replace fuse with proper size
and type. (Time-delay type “D”)
Same “Line” to L1 and L2
Measuring L1 to ground and L2 to
ground both yield 115VAC, but L1 to
L2 yields 0VAC.
Correct wiring.
No call for auxiliary or
Verify that the thermostat is indicating Set thermostat to engage auxiliaNo W2 signal at
ry or emergency heat (note some
Heat pump termi- emergency heat from ther- that auxiliary or emergency heat
mostat.
should be on.
thermostats require a jumper benal strip
tween auxiliary and emergency.
Check the thermostat manual).
Faulty thermostat.
Thermostat doesn’t indicate a call for Replace thermostat.
auxiliary or emergency when it
should.
Faulty thermostat.
Thermostat indicates auxiliary or
Replace thermostat.
emergency but no 24VAC signal present across C and the auxiliary and/
or emergency pin at the thermostat.
Faulty thermostat wiring.
24VAC signal is present across C
and the auxiliary and/or emergency
pin at the thermostat but no 24VAC
signal is present across W2 and C at
the heat pump terminal strip.
No 24VAC signal Plenum Heater transform- Voltmeter does not show 24VAC
across transformer secondary windfrom C to ground er is burned out.
ing.
at the plenum
heater control
connector
Plenum heater control
board is faulty.
Transformer tested OK in previous
step.
Correct wiring.
Replace transformer.
Replace control board.
No 24VAC signal Faulty wiring.
from 1 to ground
at the plenum
heater control
connector
24VAC present across C and ground Correct wiring.
at the plenum heater, but not across
ground of the plenum heater and I of
the heat pump terminal strip
Faulty wiring.
If previous step tested OK, 24VAC is Correct wiring.
present across ground of the plenum
heart and 1 of the heat pump terminal
strip, but not across ground of the
plenum heater and 1 of the plenum
heater.
001200MAN-05
Page 32
02 JAN 2014
PLENUM HEATER TROUBLE SHOOTING
Fault
Possible Cause
Verification
Recommended Action
No 24VAC signal Faulty Plenum Heater
from 1 to ground Relay in heat pump
at the plenum
heater control
connector
24VAC is present across pin 1 and Replace relay.
pin 3 of the relay, 24VAC is present
from heat pump terminal strip I to
plenum heater ground, but not from
heat pump terminal strip 1 to plenum
heater ground.
Thermal overload Fan not operating
is tripped.
See Fan Not Operating section
Correct problem. Reset thermal
overload.
Reset thermal overload
Replace if faulty.
Faulty overload
DOMESTIC HOT WATER (DHW) TROUBLE SHOOTING
Fault
Insufficient hot
water
(Tank Problem)
Insufficient hot
water
(Heat Pump
Problem)
Water is too hot.
Possible Cause
Verification
Recommended Action
Thermostat on hot water
tank set too low. Should
be set at 120°F. (140°F if
required by local code)
Visually inspect the setting.
Readjust the setting to 120°F.
(140°F if required by local code)
Breaker tripped, or fuse
blown in electrical supply
to hot water tank.
Check both line and load sides of
fuses. If switch is open determine
why.
Replace blown fuse or reset
breaker.
Reset button tripped on
hot water tank.
Check voltage at elements with
multimeter.
Push reset button.
Circulator pump not
operating.
Visually inspect the pump to see if
shaft is turning. Use an amprobe to
measure current draw.
Replace if faulty.
Blockage or restriction in Check water flow and power to
the water line or hot water pump. Check water lines for
heat exchanger.
obstruction
Remove obstruction in water
lines. Acid treat the domestic hot
water coil.
Faulty DHW cutout (failed
open).
Check contact operation. Should
close at 120°F and open at 140°F.
Replace DHW cutout if faulty.
Heat pump not running
enough hours to make
sufficient hot water.
Note the amount of time the heat
pump runs in any given hour.
Temporarily turn up the tank
thermostats until colder weather
creates longer run cycles.
Faulty DHW cutout (failed
closed).
Check contact operation. Should
close at 120°F and open at 140°F.
Replace DHW cutout if faulty.
Thermostat on hot water
tank set too high. Should
be set at 120°F. (140°F if
required by local code)
Visually inspect the setting.
Readjust the setting to 120°F.
(140°F if required by local code)
Trouble Shooting Tools
Dole flow control Valve
Refrigeration Gauges
In-line Flowmeter
02 JAN 2014
Digital Thermometer
Page 33
Multimeter Voltmeter /
Amprobe
The Dole® flow control is a simple, selfcleaning device designed to deliver a constant
volume of water from any outlet whether the
pressure is 15 psig or as high as 125 psi. The
controlling mechanism consists of a flexible
orifice that varies its area inversely with
pressure so that a constant flow is maintained.
001200MAN-05
REPAIR PROCEDURES
PUMP DOWN PROCEDURE
STEP 1
Connect the refrigerant recovery unit to the heat pump service ports via a refrigeration charging manifold
and to a recovery tank as per the instructions in the recovery unit manual. If there was a compressor
burn out, the refrigerant cannot be reused and must be disposed of according to local codes.
STEP 2
All water coil heat exchangers must either have full flow or be completely drained of fluid before recovery
begins. Failure to do so can freeze and rupture the heat exchanger, voiding its warranty. (Note that this
does not apply to double wall domestic hot water exchangers (desuperheater coils)
STEP 3
Ensure all hose connections are properly purged of air. Start the refrigerant recovery as per the instructions
in the recovery unit manual.
STEP 4
Allow the recovery unit suction pressure to reach a vacuum. Once achieved, close the charging manifold
valves. Shut down, purge and disconnect the recovery unit as per the instructions in its manual. Ensure the
recovery tank valve is closed before disconnecting the hose to it.
STEP 5
Connect a nitrogen tank to the charging manifold and add nitrogen to the heat pump until a positive pressure of 5-10PSIG is reached. This prevents air from being sucked into the unit by the vacuum when the
hoses are disconnected.
STEP 6
The heat pump is now ready for repairs. Always ensure nitrogen is flowing through the system during any
soldering procedures to prevent soot buildup inside the pipes. Maritime Geothermal Ltd. recommends replacing the liquid line filter-drier anytime the refrigeration system has been exposed to the atmosphere.
VACUUM AND CHARGING PROCEDURE
STEP 1
After completion of repairs and nitrogen pressure testing, the refrigeration circuit is ready for vacuuming.
STEP 2
Release the refrigerant circuit pressure and connect the vacuum pump to the charging manifold. Start the
vacuum pump and open the charging manifold valves. Vacuum until the vacuum gauge remains at less
than 500 microns for at least 1 minute with the vacuum pump valve closed.
STEP 3
Close the charging manifold valves then shut off and disconnect the vacuum pump. Place a refrigerant tank
with the proper refrigerant on a scale and connect it to the charging manifold. Purge the hose to the tank.
STEP 4
Weigh in the appropriate amount of refrigerant through the low pressure (suction) service port. Refer to the
label on the unit or the Refrigerant Charge Chart in the MODEL SPECIFIC INFORMATION section for the
proper charge amount.
STEP 5
If the unit will not accept the entire charge, the remainder can be added through the low pressure service
port after the unit has been restarted.
REPLACMENT PROCEDURE FOR A COMPRESSOR BURN-OUT
STEP 1
Pump down the unit as per the Pump Down Procedure above. Discard the refrigerant according to local
codes.
STEP 2
Replace the compressor. Replace the liquid line filter-drier.
STEP 3
Vacuum the unit until it remains under 500 microns for several minutes with the vacuum pump valve closed.
STEP 4
Charge the unit with NEW REFRIGERANT and operate it for continuously for 2 hours. Pump down the unit
and replace the filter-drier. Vacuum the unit until it remains under 500 microns for several minutes with the
vacuum pump valve closed.
STEP 5
Charge the unit (refrigerant can be re-used) and operate it for 2-3 days. Perform an acid test. If it fails,
pump down the unit and replace the filter-drier.
STEP 6
Charge the unit (refrigerant can be re-used) and operate it for 2 weeks. Perform and acid test, If it fails
pump down the unit and replace the filter-drier.
STEP 7
Charge the unit a final time. Unit should now be clean and repeated future burn-outs can be avoided.
001200MAN-05
Page 34
02 JAN 2014
Model Specific Information
This section provides general information particular to each model. For complete specifications please see the specifications
document for the desired model.
REFRIGERANT CHARGE CHART
SHIPPING INFORMATION
Table 14 - Refrigerant - R410a
SIZE
Lbs.
kg
25
7.5
3.4
45
7.5
3.4
55
8.0
65
Table 15 - Shipping Information
MODEL
WEIGHT
DIMENSIONS in (cm)
Lbs. (kg)
L
W
H
25
370 (168)
44 (112)
36 (91)
66 (167)
3.6
45
390 (177)
44 (112)
36 (91)
66 (167)
10.0
4.5
55
460 (209)
44 (112)
36 (91)
66 (167)
75
12.5
5.7
65
490 (222)
44 (112)
36 (91)
66 (167)
80
11.5
5.2
75
530 (240)
44 (112)
36 (91)
66 (167)
80
598 (271)
44 (112)
36 (91)
68 (173)
System contains POE oil.
STANDARD CAPACITY RATINGS
The tables below depict the results of standard capacity rating tests according to C13256-1, which is identical to ISO13256-1.
Stage 1 values do not apply to single stage units. Refer to the Electrical Tables to determine which models are single stage.
Table 16 - Standard Capacity Ratings - Ground Loop Heating*
EAT 68°F (20°C)
Model
60Hz
STAGE 1 - ELT 41°F (5°C)
STAGE 2 - ELT 32°F (0°C)
Nominal
Size
Tons
Liquid Flow
USGPM
L/s
Pressure
Drop
PSI kPA
25
2
8.0
0.50
2.9
20.0
45
3
10.0
0.63
4.4
30.8
55
4
12.0
0.76
4.1
28.3
65
5
14.0
0.88
5.3
36.5
75
6
16.0
1.01
4.1
28.6
80
6
17.0
1.07
4.5
31.0
Mode
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Airflow
CFM
680
800
1030
1200
1240
1500
1540
1900
1660
2100
2400
L/s
320
378
486
566
585
708
727
897
783
991
1133
Input
Energy
Watts
1,035
1,450
1,535
2,155
2,045
2,700
2,565
3,390
3,435
4,355
4,940
Capacity
BTU/Hr
15,200
18,300
22,000
27,200
29,300
35,900
35,900
44,000
45,700
53,500
63,000
kW
4.5
5.4
6.4
8.0
8.6
10.5
10.5
12.8
13.4
15.7
18.4
* 15% NaCl by Weight Ground Loop Fluid
EAT 68°F (20°C)
Model
W/W
4.3
3.7
4.2
3.7
4.2
3.9
4.1
3.8
3.9
3.6
3.7
REV-09
Table 17 - Standard Capacity Ratings - Ground Water Heating
Nominal
Size
Tons
COPH
60Hz
ELT 50°F (10°C)
Liquid Flow
USGPM
L/s
Pressure
Drop
PSI kPA
25
2
8.0
0.50
2.7
18.6
45
3
10.0
0.63
4.0
27.3
55
4
12.0
0.76
3.5
24.1
65
5
14.0
0.88
4.3
29.7
75
6
16.0
1.01
3.6
24.8
80
6
17.0
1.07
4.1
28.3
Mode
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Airflow
CFM
680
800
1030
1200
1240
1500
1540
1900
1660
2100
2400
L/s
320
378
486
566
585
708
727
897
783
991
1133
Input
Energy
Watts
1,070
1,540
1,625
2,375
2,075
2,960
2,670
3,740
3,540
4,780
5,315
Capacity
BTU/Hr
17,900
23,100
25,500
35,700
34,700
47,500
42,800
58,700
52,000
68,500
77,500
kW
5.2
6.8
7.5
10.5
10.2
13.9
12.5
17.2
15.2
20.1
22.7
COPH
W/W
4.9
4.4
4.6
4.4
4.9
4.7
4.7
4.6
4.3
4.2
4.3
REV-09
02 JAN 2014
Page 35
001200MAN-05
STADARD CAPACITY RATINGS (continued)
Table 18 - Standard Capacity Ratings - Ground Loop Cooling*
EAT 80.6°F (27°C)
Model
Size
Tons
60Hz
STAGE 1 - ELT 68°F (20°C)
STAGE 2 - ELT 77°F (25°C)
Liquid Flow
USGPM
L/s
Pressure
Drop
PSI kPA
25
2
8.0
0.50
2.7
18.5
45
3
10.0
0.63
3.7
25.5
55
4
12.0
0.76
3.8
26.2
65
5
14.0
0.88
4.1
28.2
75
6
16.0
1.01
3.5
24.2
80
6
17.0
1.07
4.2
29.0
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
CFM
680
800
1030
1200
1240
1500
1540
1900
1660
2100
L/s
320
378
486
566
585
708
727
897
783
991
Input
Energy
Watts
790
1,460
1,130
2,155
1,470
2,640
1,910
3,445
2,620
4,300
Stage 1
2400
1133
4,950
Mode
Airflow
Capacity
BTU/Hr
20,100
24,800
26,800
35,100
36,000
45,700
45,500
57,600
55,000
67,500
84,200
COPc
EER
kW
5.9
7.3
7.8
10.3
10.5
13.4
13.3
16.9
16.1
19.8
W/W
7.5
5.7
6.9
4.8
7.2
5.1
6.7
4.9
6.3
4.7
BTU/W
25.5
17.0
23.7
16.3
24.5
17.3
23.8
16.8
21.0
15.7
24.7
5.00
17.1
* 15% NaCl by Weight Ground Loop Fluid
REV-09
Table 19 - Standard Capacity Ratings - Ground Water Cooling
60Hz
EAT 80.6°F (27°C)
ELT 59°F (15°C)
Tons
USGPM
L/s
Pressure
Drop
PSI kPA
25
2
8.0
0.50
2.6
18.1
45
3
10.0
0.63
3.7
28.3
55
4
12.0
0.76
3.3
22.7
65
5
14.0
0.88
4.1
28.0
75
6
16.0
1.01
3.4
23.6
80
6
17.0
1.07
3.9
26.9
Model
Size
Liquid Flow
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
Stage 1
Stage 2
CFM
680
800
1030
1200
1240
1500
1540
1900
1660
2100
L/s
320
378
486
566
585
708
727
897
783
991
Input
Energy
Watts
640
1,160
1,080
1,805
1,315
2,245
1,705
2,865
2,305
3,710
Stage 1
2400
1133
4,130
Mode
Airflow
COPc
EER
BTU/Hr
21,000
26,800
29,500
38,500
37,500
50,500
47,200
62,600
56,500
72,000
Capacity
kW
6.2
7.9
8.6
11.3
11.0
14.8
13.8
18.3
16.6
21.1
W/W
9.6
6.8
8.0
6.2
8.3
6.6
8.1
6.4
7.2
5.7
BTU/W
32.7
23.1
27.3
21.3
28.5
22.5
27.5
21.8
24.5
19.4
87,900
25.8
6.23
21.1
REV-09
001200MAN-05
Page 36
02 JAN 2014
CAPACITY RATINGS
Heating Mode
R-25-HACW-P-1T
Source Data (Outdoor Loop)
Nominal 2 ton
Power Consumption
ELT
Evap.
Temp
Flow
LLT
Delta T
HAB
Compressor
Fan*
°F
°C
°F
°C
USGPM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
Watts Amps
Watts
Watts
24.0
15
7.0
20.4
3.6
12,091
1,431
73
1,497
-4.4
-9.4
0.442
-6.5
2.0
3,543
30.0
20
7.0
26.0
4.0
13,328
-1.1
-6.7
0.442
-3.3
2.2
3,905
36.0
25
7.0
31.6
4.4
14,644
2.2
-3.9
0.442
-0.2
2.4
4,291
42.0
30
7.0
37.1
4.9
16,286
5.6
-1.1
0.442
2.8
2.7
4,772
45.0
35
7.0
39.8
5.2
18,061
7.2
1.7
0.442
4.4
2.9
5,292
51.0
40
7.0
45.4
5.6
19,694
10.6
4.4
0.442
7.4
3.1
5,770
57.0
45
7.0
50.9
6.1
21,427
13.9
7.2
0.442
10.5
3.4
6,278
63.0
50
7.0
56.3
6.7
23,268
17.2
10.0
0.442
13.5
3.7
6,817
6.6
1,460
6.7
1,491
6.9
73
1,526
1,556
1,531
7.0
73
1,597
1,575
7.2
73
1,633
1,614
7.4
EAT
Cond.
Temp.
Air
Flow
LAT
Delta T
Net
Output
W/W
°F
°C
°F
°C
CFM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
3.33
68
100
800
89.3
21.3
17,019
20.0
37.8
378
31.8
11.8
4,987
Effective COPh
73
73
1,673
R410a 60 Hz
Sink Data (Indoor Loop)
3.52
3.72
3.96
4.21
4.42
1,658
7.6
73
1,716
4.63
1,706
7.8
73
1,764
4.84
68
102
800
90.9
22.9
18,355
20.0
38.9
378
32.7
12.7
5,378
19,776
68
104
800
92.7
24.7
20.0
40.0
378
33.7
13.7
5,794
68
106
800
94.9
26.9
21,555
20.0
41.1
378
35.0
15.0
6,315
68
108
800
97.9
29.9
23,469
20.0
42.2
378
36.6
16.6
6,876
68
110
800
100.2
32.2
25,236
20.0
43.3
378
37.9
17.9
7,394
68
112
800
102.6
34.6
27,119
20.0
44.4
378
39.2
19.2
7,946
68
114
800
105.1
37.1
29,123
20.0
45.6
378
40.6
20.6
8,533
* @ 37.3Pa (0.15inH2o) Ext. Static
Compressor: ZPS20K5E-PFV
Cooling Mode
R-25-HACW-P-1T
Source Data (Indoor Loop)
EAT
Evap.
Airflow
Temp
LAT Delta T Latent Sensible
°F
°C
BTU/Hr BTU/Hr
Watts
Watts
Power Consumption
HAB
Compressor
°F
°C
°F
°C
CFM
L/s
°F
°C
80.6
46
800
56.3
24.3 9,561 20,629 30,190 1,142
6,044
BTU/Hr
Watts
27.0
7.8
378
13.5
13.5 2,801
80.6
47
800
56.6
24.0 9,422 20,328 29,749 1,206
27.0
8.1
378
13.7
13.3 2,760
5,956
800
57.0
23.6 9,270 20,001 29,271 1,276
378
13.9
13.1 2,716
80.6
47
800
58.4
22.2 8,716 18,805 27,521 1,320
8.5
378
14.7
12.3 2,554
48
800
59.0
21.6 7,841 17,951 25,792 1,366
27.0
8.7
378
15.0
12.0 2,297
°F
°C
°F
°C
USGPM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
53
70
7.0
62.8
9.8
34,321
0.442 17.1
4.5
68
1,203
25.1
4.8
68
1,266
23.5
5.1
68
1,337
21.9
5.4
68
1,380
19.9
5.7
68
1,425
18.1
8,064
5.84
7,557
5.30
80.6
48
800
59.5
21.1 7,679 17,580 25,258 1,453
27.0
8.9
378
15.3
11.7 2,250
80.6
49
800
59.9
20.7 7,507 17,187 24,694 1,547
6.1
68
1,512
7,401
16.7
4.89
27.0
9.2
378
15.5
11.5 2,200
80.6
49
800
60.4
20.2 7,326 16,774 24,100 1,648
27.0
9.4
378
15.8
11.2 2,147
6.5
68
1,606
15.4
6.9
68
1,707
14.1
7,235
4.51
7,061
4.14
11.7 21.1
58
75
14.4 23.9
63
80
17.2 26.7
68
85
20.0 29.4
73
90
22.8 32.2
78
95
25.6 35.0
83
100
28.3 37.8
88
105
31.1 40.6
Delta
Rejection
T
5.5
10,056
67.7
9.7
34,097
0.442 19.9
5.4
9,990
72.7
9.7
33,859
0.442 22.6
5.4
9,920
77.2
9.2
32,257
0.442 25.1
7.0
7.0
7.0
5.1
9,451
82.2
9.2
30,687
0.442 27.9
5.1
8,991
87.2
9.2
30,450
0.442 30.6
5.1
8,922
92.1
9.1
30,206
0.442 33.4
7.0
7.0
7.0
5.0
8,850
97.0
9.0
29,958
0.442 36.1
5.0
8,778
7.0
* @ 37.3Pa (0.15inH2o) Ext. Static
Compressor: ZPS20K5E-PFV
02 JAN 2014
EER
COPc
6.42
27.0
4,915
Watts
8,576
80.6
5,036
LLT
6.88
47
5,151
Flow
8,716
8.3
5,260
Cond.
Temp.
7.35
27.0
5,510
ELT
8,846
80.6
5,860
Efficiency
Fan* Effective
Watts Amps Watts
R410a 60 Hz
Sink Data (Outdoor Loop)
Page 37
001200MAN-05
CAPACITY RATINGS (continued)
Heating Mode
R-45-HACW-P-1T
Source Data (Outdoor Loop)
Nominal 3 ton
Power Consumption
ELT
Evap.
Temp
Flow
LLT
Delta T
HAB
°F
°C
°F
°C
USGPM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
Watts Amps Watts
Watts
26.0
15
10.0
21.9
4.1
19,393
1,963
2,128
-3.3
-9.4
0.631
-5.6
2.3
5,682
32.0
20
10.0
27.6
4.4
21,005
0.0
-6.7
0.631
-2.5
2.5
6,154
38.0
25
10.0
33.2
4.8
22,718
3.3
-3.9
0.631
0.7
2.7
6,656
44.0
30
10.0
38.7
5.3
25,249
6.7
-1.1
0.631
3.7
3.0
7,398
49.0
35
10.0
43.4
5.6
28,175
9.4
1.7
0.631
6.3
3.1
8,255
55.0
40
10.0
48.9
6.1
30,329
12.8
4.4
0.631
9.4
3.4
8,886
61.0
45
10.0
54.5
6.5
32,592
16.1
7.2
0.631
12.5
3.6
9,549
67.0
50
10.0
60.0
7.0
34,965
19.4
10.0
0.631
15.6
3.9
10,245
Compressor
8.4
2,045
8.8
2,130
9.1
179
179
2,211
2,295
2,239
9.5
179
2,404
2,324
9.8
179
2,479
2,417 10.2
EAT
Cond.
Temp.
Air
Flow
LAT
Delta T
Net
Output
W/W
°F
°C
°F
°C
CFM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
3.63
61
96
22.7
26,396
16.1
35.6
12.6
7,734
Fan* Effective COPh
179
179
2,572
R410a 60 Hz
Sink Data (Indoor Loop)
3.75
3.87
4.05
4.30
4.43
2,514 10.6
179
2,669
4.55
2,615 11.1
179
2,770
4.67
62
99
16.7
37.2
63
102
17.2
38.9
63
105
17.2
40.6
63
107
17.2
41.7
63
110
17.2
43.3
64
113
17.8
45.0
65
116
18.3
46.7
1,200 83.7
566
28.7
1,200 86.3
566
30.2
1,200 89.0
566
24.3
28,290
13.5
8,289
26.0
30,291
31.7
14.5
8,875
1,200 91.5
28.5
33,196
33.1
15.8
9,726
1,200 94.3
31.3
36,401
17.4
10,665
566
566
34.6
1,200 96.4
33.4
38,873
35.8
18.6
11,390
1,200 99.6
35.6
41,467
37.6
19.8
12,150
1,200 103.0
38.0
44,185
21.1
12,946
566
566
566
39.4
* @ 37.3Pa (0.15inH2o) Ext. Static
Compressor: ZPS30K5E-PFV
Cooling Mode
R-45-HACW-P-1T
Source Data (Indoor Loop)
EAT
Evap.
Airflow
Temp
LAT Delta T Latent Sensible
°F
°C
BTU/Hr BTU/Hr
Watts
Watts
Power Consumption
HAB
Compressor
°F
°C
°F
°C
CFM
L/s
°F
°C
80.6
44
1,200
57.4
23.2 13,299 28,417 41,716 1,487
8,326
BTU/Hr
Watts
27.0
6.6
566
14.1
12.9 3,897
80.6
44
1,200
57.7
22.9 13,115 28,024 41,140 1,611
27.0
6.8
566
14.3
12.7 3,843
80.6
45
1,200
58.0
22.6 12,968 27,709 40,677 1,737
27.0
7.2
566
14.4
12.6 3,800
80.6
46
1,200
58.4
22.2 12,721 27,182 39,904 1,881
8,211
8,119
7,964
Watts
EER
COPc
°F
°C
°F
°C
USGPM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
51
70
10.0
60.5
9.5
47,375
0.631 15.8
5.3
13,881
10.0
65.5
9.5
47,222
0.631 18.6
5.3
13,836
6.0
171
1,642
25.4
6.4
171
1,766
23.3
6.9
171
1,892
11,918
21.5
6.30
566
14.7
12.3 3,727
1,200
58.7
21.9 12,344 26,670 39,014 2,031
27.0
7.9
566
14.8
12.2 3,617
80.6
47
1,200
59.0
21.6 12,165 26,283 38,447 2,171
27.0
8.3
566
15.0
12.0 3,564
80.6
48
1,200
59.4
21.2 11,931 25,777 37,707 2,317
7.4
171
2,036
19.6
7.9
171
2,192
17.8
11,692
5.74
11,431
5.22
8.4
171
2,332
11,265
16.5
4.83
27.0
8.6
566
15.2
11.8 3,496
80.6
48
1,200
59.9
20.7 11,685 25,246 36,931 2,471
27.0
8.9
566
15.5
11.5 3,424
9.0
171
2,478
15.2
9.6
171
2,632
14.0
11,048
4.46
10,821
4.11
10.6 21.1
56
75
13.3 23.9
61
80
16.1 26.7
66
85
18.9 29.4
72
90
22.2 32.2
77
95
25.0 35.0
82
100
27.8 37.8
87
105
30.6 40.6
10.0
Delta
Rejection
T
70.4
9.4
47,190
0.631 21.4
5.2
13,826
10.0
75.4
9.4
46,908
0.631 24.1
5.2
13,744
10.0
81.8
9.8
46,530
0.631 27.7
5.4
13,633
86.8
9.8
46,441
0.631 30.4
10.0
5.4
13,607
10.0
91.7
9.7
46,200
0.631 33.2
5.4
13,537
10.0
96.7
9.7
45,950
0.631 35.9
5.4
13,463
* @ 37.3Pa (0.15inH2o) Ext. Static
Compressor: ZPS30K5E-PFV
001200MAN-05
LLT
6.82
46
7,397
Flow
12,054
7.6
7,552
Cond.
Temp.
7.44
27.0
7,701
ELT
12,223
80.6
7,814
Efficiency
Fan* Effective
Watts Amps Watts
R410a 60 Hz
Sink Data (Outdoor Loop)
Page 38
02 JAN 2014
CAPACITY RATINGS (continued)
Heating Mode
R-55-HACW-P-1T
Source Data (Outdoor Loop)
Nominal 4 ton
Power Consumption
ELT
Evap.
Temp
Flow
LLT
Delta T
HAB
Compressor
Fan*
°F
°C
°F
°C
USGPM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
Watts Amps
Watts
Watts
27.0
15
12.0
22.3
4.7
26,809
2,567 11.8
185
2,718
-2.8
-9.4
0.757
-5.4
2.6
7,855
33.0
20
12.0
27.8
5.2
29,763
0.6
-6.7
0.757
-2.3
2.9
8,721
39.0
25
12.0
33.2
5.8
32,940
3.9
-3.9
0.757
0.7
3.2
9,651
45.0
30
12.0
38.7
6.3
36,095
7.2
-1.1
0.757
3.7
3.5
10,576
50.0
35
12.0
43.4
6.6
39,435
10.0
1.7
0.757
6.3
3.7
11,554
56.0
40
12.0
48.8
7.2
43,264
13.3
4.4
0.757
9.3
4.0
12,676
62.0
45
12.0
54.1
7.9
47,338
16.7
7.2
0.757
12.3
4.4
13,870
68.0
50
12.0
59.4
8.6
51,663
20.0
10.0
0.757
15.2
4.8
15,137
2,633 12.1
EAT
Cond.
Temp.
Air
Flow
LAT
Delta T
Net
Output
W/W
°F
°C
°F
°C
CFM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
3.86
68
98
23.6
35,782
20.0
36.7
13.1
10,484
Effective COPh
185
2,784
4.10
2,699 12.5
185
2,850
4.36
2,791 12.8
185
2,942
4.56
2,885 13.1
185
3,033
4.78
2,955 13.4
185
3,102
5.06
3,026 13.8
185
3,174
5.34
3,100 14.1
185
3,247
R410a 60 Hz
Sink Data (Indoor Loop)
5.64
68
100
20.0
37.8
68
102
20.0
38.9
68
104
20.0
40.0
68
106
20.0
41.1
68
108
20.0
42.2
68
110
20.0
43.3
68
112
20.0
44.4
1,500 91.6
708
33.1
1,500 93.7
25.7
38,963
34.3
14.3
11,416
1,500 96.0
28.0
42,364
708
35.5
15.5
12,413
1,500 98.3
708
30.3
45,834
16.8
13,429
708
36.8
1,500 100.0
32.0
49,511
37.8
17.8
14,507
1,500 102.7
34.7
53,577
39.3
19.3
15,698
1,500 105.5
37.5
57,895
20.8
16,963
40.4
62,471
22.5
18,304
708
708
708
40.8
1,500 108.4
708
42.5
* @ 37.3Pa (0.15inH2o) Ext. Static
Compressor: ZPS40K5E-PFV
Cooling Mode
R-55-HACW-P-1T
Source Data (Indoor Loop)
EAT
Evap.
Airflow
Temp
LAT Delta T Latent Sensible
°F
°C
BTU/Hr BTU/Hr
Watts
Watts
Power Consumption
HAB
Compressor
°F
°C
°F
°C
CFM
L/s
°F
°C
80.6
43.6
1,500
58.3
22.3 16,911 36,135 53,046 1,993
BTU/Hr
Watts
Watts
EER
COPc
°F
°C
°F
°C
USGPM
L/s
°F
°C
51
70
12.0
9.1
192
2,297
22.7
708
14.6
12.4 4,955 10,587 15,542
1,500
58.7
21.9 16,606 35,484 52,090 2,139
27.0
6.6
708
14.8
12.2 4,866 10,397 15,262
80.6
44
1,500
59.1
21.5 16,289 34,806 51,095 2,287
27.0
6.7
708
15.1
11.9 4,773 10,198 14,971
80.6
44.3
1,500
59.5
21.1 15,993 34,173 50,166 2,373 10.3
7.23
6.64
9.7
192
2,444
20.9
6.12
27.0
6.8
708
15.3
11.7 4,686 10,013 14,699
80.6
45
1,500
60.2
20.4 16,727 32,470 49,197 2,455 11.0
27.0
7.0
708
15.7
11.3 4,901
80.6
45
1,500
60.6
20.0 16,409 31,853 48,262 2,605 11.6
27.0
7.2
708
15.9
11.1 4,808
80.6
45
1,500
61.1
19.5 16,009 31,077 47,087 2,761 12.3
192
2,530
19.8
192
2,614
18.8
5.81
14,415
5.51
192
2,764
14,141
17.5
5.12
27.0
7.3
708
16.1
10.9 4,691
80.6
45
1,500
61.6
19.0 15,594 30,270 45,864 2,924 13.0
27.0
7.4
708
16.4
10.6 4,569
192
2,920
16.1
192
3,083
14.9
13,796
4.72
13,438
4.36
10.6 21.1
56
75
13.3 23.9
61
80
16.1 26.7
66
85
18.9 29.4
71
90
21.7 32.2
76
95
24.4 35.0
81
100
27.2 37.8
86
105
30.0 40.6
BTU/Hr
Watts
5.6
17,727
66.0 10.0 60,047
0.757 18.9
12.0
°F
°C
61.1 10.1 60,504
0.757 16.2
12.0
Delta
Rejection
T
5.6
17,593
70.9
9.9
59,555
0.757 21.6
5.5
17,449
12.0
75.8
9.8
58,920
0.757 24.3
5.5
17,263
12.0
81.2 10.2 58,230
0.757 27.3
12.0
17,061
86.1 10.1 57,809
0.757 30.1
12.0
5.7
5.6
16,938
91.0 10.0 57,166
0.757 32.8
5.6
16,749
12.0
95.9
9.9
56,499
0.757 35.5
5.5
16,554
* @ 37.3Pa (0.15inH2o) Ext. Static
Compressor: ZPS40K5E-PFV
02 JAN 2014
LLT
24.7
6.4
8,869
Flow
2,151
43.8
9,106
Cond.
Temp.
192
27.0
9,333
ELT
8.5
80.6
9,514
Efficiency
Fan* Effective
Watts Amps Watts
R410a 60 Hz
Sink Data (Outdoor Loop)
Page 39
001200MAN-05
CAPACITY RATINGS (continued)
Heating Mode
R-65-HACW-P-1T
Source Data (Outdoor Loop)
Nominal 5 ton
Power Consumption
ELT
Evap.
Temp
Flow
LLT
Delta T
HAB
Compressor
Fan*
°F
°C
°F
°C
USGPM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
Watts Amps
Watts
Watts
26.0
15
14.0
21.2
4.8
31,644
3,290 14.9
300
3,573
-3.3
-9.4
0.883
-6.0
2.6
9,272
32.0
20
14.0
26.8
5.2
34,798
0.0
-6.7
0.883
-2.9
2.9
10,196
38.0
25
14.0
32.3
5.7
37,954
3.3
-3.9
0.883
0.2
3.2
11,120
44.0
30
14.0
37.6
6.4
42,566
6.7
-1.1
0.883
3.1
3.6
12,472
49.0
35
14.0
42.2
6.8
47,314
9.4
1.7
0.883
5.7
3.8
13,863
55.0
40
14.0
47.6
7.4
51,599
12.8
4.4
0.883
8.7
4.1
15,118
61.0
45
14.0
53.0
8.0
56,159
16.1
7.2
0.883
11.7
4.5
16,455
67.0
50
14.0
58.3
8.7
61,001
19.4
10.0
0.883
14.6
4.8
17,873
3,384 15.3
EAT
Cond.
Temp.
Flow
LAT
Delta T
Net
Output
W/W
°F
°C
°F
°C
CFM
L/min
°F
°C
°F
°C
BTU/Hr
Watts
3.56
68
97
1,900 90.6
22.6
43,391
20.0
36.1
12.6
12,713
Effective COPh
300
3,667
3.74
3,522 15.9
300
3,806
3.89
3,620 16.3
300
3,903
4.16
3,765 16.9
300
4,045
4.40
3,865 17.4
300
4,144
4.62
3,968 17.8
300
4,247
4.85
4,074 18.3
300
4,353
R410a 60 Hz
Sink Data (Indoor Loop)
5.08
68
99
20.0
37.2
68
102
20.0
38.9
68
104
20.0
40.0
68
107
20.0
41.7
68
109
20.0
42.8
68
111
20.0
43.9
68
113
20.0
45.0
897
32.6
1,900 92.4
24.4
46,866
33.6
13.6
13,732
1,900 94.3
26.3
50,495
34.6
14.6
14,795
1,900 96.9
28.9
55,440
16.1
16,244
897
897
897
36.1
1,900 99.0
31.0
60,717
37.2
17.2
17,790
1,900 101.4
33.4
65,344
38.5
18.5
19,146
1,900 103.9
35.9
70,253
19.9
20,584
38.6
75,456
21.4
22,108
897
897
897
39.9
1,900 106.6
897
41.4
* @ 49.7Pa (0.20inH2o) Ext. Static
Compressor: ZPS51K5E-PFV
Cooling Mode
R-65-HACW-P-1T
Source Data (Indoor Loop)
EAT
Evap.
Airflow
Temp
LAT Delta T Latent Sensible
°F
°C
BTU/Hr BTU/Hr
Watts
Watts
Power Consumption
HAB
Compressor
°F
°C
°F
°C
CFM
L/s
°F
°C
80.6
44.8
1,900
56.0
24.6 19,665 49,095 68,760 2,373 10.8
BTU/Hr
Watts
27.0
7.1
897
13.3
13.7 5,762 14,385 20,147
45.1
1,900
56.4
24.2 19,362 48,337 67,698 2,574 11.6
27.0
7.3
897
13.5
13.5 5,673 14,163 19,835
80.6
45.4
1,900
56.8
23.8 19,043 47,542 66,585 2,777 12.4
27.0
7.4
897
13.8
13.2 5,580 13,930 19,509
80.6
45.7
1,900
57.5
23.1 18,462 46,091 64,553 2,896 13.2
ELT
Cond.
Temp.
Flow
LLT
Watts
EER
COPc
°F
°C
°F
°C
USGPM
L/s
°F
°C
325
2,663
25.8
49
70
14.0
7.56
9.4
21.1
325
2,864
23.6
54
75
6.93
325
3,067
21.7
6.36
27.0
7.6
897
14.2
12.8 5,409 13,504 18,914
80.6
46
1,900
58.0
22.6 18,682 43,799 62,481 3,008 14.0
27.0
7.8
897
14.4
12.6 5,474 12,833 18,307
80.6
46
1,900
58.5
22.1 18,309 42,926 61,235 3,214 14.8
27.0
7.9
897
14.7
12.3 5,365 12,577 17,942
80.6
47
1,900
58.9
21.7 17,919 42,012 59,931 3,429 15.7
325
3,186
20.3
325
3,307
18.9
5.94
5.54
325
3,513
17.4
5.11
27.0
8.1
897
15.0
12.0 5,250 12,309 17,560
80.6
47
1,900
59.4
21.2 17,512 41,056 58,567 3,653 16.6
27.0
8.3
897
15.2
11.8 5,131 12,029 17,160
325
3,728
16.1
325
3,952
14.8
4.71
4.34
12.2 23.9
59
80
15.0 26.7
64
85
17.8 29.4
70
90
21.1 32.2
75
95
23.9 35.0
80
100
26.7 37.8
85
105
29.4 40.6
6.1
22,612
6.0
22,135
6.2
21,640
6.1
21,481
90.9 10.9 72,743
0.883 32.7
14.0
22,735
86.0 11.0 73,315
0.883 30.0
14.0
6.2
81.1 11.1 73,856
0.883 27.3
14.0
22,845
74.8 10.8 75,547
0.883 23.8
14.0
6.2
70.0 11.0 77,174
0.883 21.1
14.0
BTU/Hr
Watts
65.1 11.1 77,594
0.883 18.4
14.0
°F
°C
60.1 11.1 77,969
0.883 15.6
14.0
Delta
Rejection
T
6.1
21,314
95.8 10.8 72,145
0.883 35.5
6.0
21,138
* @ 49.7Pa (0.20inH2o) Ext. Static
Compressor: ZPS51K5E-PFV
001200MAN-05
Efficiency
Fan* Effective
Watts Amps Watts
80.6
R410a 60 Hz
Sink Data (Outdoor Loop)
Page 40
02 JAN 2014
CAPACITY RATINGS (continued)
Heating Mode
R-75-HACW-P-1T
Source Data (Outdoor Loop)
Nominal 6 ton
Power Consumption
ELT
Evap.
Temp
Flow
LLT
Delta T
HAB
Compressor
Fan*
°F
°C
°F
°C
USGPM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
Watts Amps
Watts
Watts
28.0
15
16.0
22.9
5.1
38,593
3,695 17.5
410
4,094
-2.2
-9.4
1.009
-5.0
2.8
11,308
34.0
20
16.0
28.4
5.6
42,497
1.1
-6.7
1.009
-2.0
3.1
12,452
40.0
25
16.0
33.9
6.1
46,404
4.4
-3.9
1.009
1.1
3.4
13,596
46.0
30
16.0
39.3
6.7
50,856
7.8
-1.1
1.009
4.1
3.7
14,901
51.0
35
16.0
44.1
6.9
55,258
10.6
1.7
1.009
6.7
3.8
16,191
57.0
40
16.0
49.5
7.5
60,316
13.9
4.4
1.009
9.7
4.2
17,672
63.0
45
16.0
54.8
8.2
65,697
17.2
7.2
1.009
12.7
4.6
19,249
69.0
50
16.0
60.1
8.9
71,411
20.6
10.0
1.009
15.6
5.0
20,923
3,787 17.9
410
EAT
Cond.
Temp.
Air
Flow
LAT
Delta T
Net
Output
W/W
°F
°C
°F
°C
CFM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
3.73
68
97
24.6
52,075
20.0
36.1
13.6
15,258
Effective COPh
4,186
3.94
3,922 18.5
410
4,320
4.11
4,068 19.0
410
4,466
4.30
4,264 19.7
410
4,643
4.46
4,364 20.1
410
4,743
4.70
4,467 20.6
410
4,845
4.95
4,572 21.1
410
4,951
R410a 60 Hz
Sink Data (Indoor Loop)
5.20
68
99
20.0
37.2
68
102
20.0
38.9
68
104
20.0
40.0
68
107
20.0
41.7
68
109
20.0
42.8
68
111
20.0
43.9
68
113
20.0
45.0
2,100 92.6
991
33.6
2,100 94.5
26.5
56,292
34.7
14.7
16,493
2,100 96.6
28.6
60,659
991
35.9
15.9
17,773
2,100 98.9
991
30.9
65,609
17.2
19,223
991
37.2
2,100 100.7
32.7
70,689
38.2
18.2
20,712
2,100 103.2
35.2
76,088
39.5
19.5
22,294
2,100 105.8
37.8
81,818
21.0
23,973
40.6
87,893
22.6
25,752
991
991
991
41.0
2,100 108.6
991
42.6
* @ 49.7Pa (0.20inH2o) Ext. Static
Compressor: ZPS60K5E-PFV
Cooling Mode
R-75-HACW-P-1T
Source Data (Indoor Loop)
EAT
Evap.
Airflow
Temp
LAT Delta T Latent Sensible
°F
°C
BTU/Hr BTU/Hr
Watts
Watts
Power Consumption
HAB
Compressor
°F
°C
°F
°C
CFM
L/s
°F
°C
80.6
44
2,100
59.4
21.2 24,039 51,083 75,123 2,991 13.1
BTU/Hr
Watts
27.0
6.7
991
15.2
11.8 7,043 14,967 22,011
44.1
2,100
59.9
20.7 23,576 50,099 73,675 3,197 13.9
27.0
6.7
991
15.5
11.5 6,908 14,679 21,586
80.6
44.2
2,100
60.3
20.3 23,097 49,082 72,179 3,407 14.7
27.0
6.8
991
15.7
11.3 6,767 14,381 21,148
80.6
44.3
2,100
60.6
20.0 22,755 48,353 71,108 3,519 15.6
ELT
Cond.
Temp.
Flow
LLT
Watts
EER
COPc
°F
°C
°F
°C
USGPM
L/s
°F
°C
450
3,412
22.0
52
70
16.0
450
3,619
20.4
6.45
5.96
450
3,828
18.9
5.52
27.0
6.8
991
15.9
11.1 6,667 14,167 20,834
80.6
44
2,100
60.3
20.3 21,843 48,167 70,010 3,625 16.5
27.0
6.9
991
15.7
11.3 6,400 14,113 20,513
80.6
45
2,100
60.8
19.8 21,321 47,017 68,338 3,838 17.4
27.0
6.9
991
16.0
11.0 6,247 13,776 20,023
80.6
45
2,100
61.3
19.3 20,782 45,828 66,610 4,060 18.3
450
3,941
18.0
450
4,050
17.3
5.29
5.06
450
4,263
16.0
4.70
27.0
7.0
991
16.3
10.7 6,089 13,427 19,517
80.6
45
2,100
61.8
18.8 20,225 44,599 64,824 4,292 19.3
27.0
7.1
991
16.6
10.4 5,926 13,067 18,993
450
4,485
14.9
450
4,717
13.7
4.35
4.03
11.1 21.1
57
75
13.9 23.9
62
80
16.7 26.7
67
85
19.4 29.4
73
90
22.8 32.2
78
95
25.6 35.0
83
100
28.3 37.8
88
105
31.1 40.6
5.9
25,005
5.9
24,803
6.1
24,587
6.1
24,311
93.8 10.8 82,003
1.009 34.3
16.0
25,234
88.9 10.9 82,973
1.009 31.6
16.0
6.0
84.0 11.0 83,917
1.009 28.9
16.0
25,451
77.6 10.6 84,654
1.009 25.3
16.0
6.0
72.7 10.7 85,342
1.009 22.6
16.0
BTU/Hr
Watts
67.8 10.8 86,123
1.009 19.9
16.0
°F
°C
62.9 10.9 86,865
1.009 17.1
16.0
Delta
Rejection
T
6.0
24,027
98.7 10.7 81,008
1.009 37.0
5.9
23,735
* @ 49.7Pa (0.20inH2o) Ext. Static
Compressor: ZPS60K5E-PFV
02 JAN 2014
Efficiency
Fan* Effective
Watts Amps Watts
80.6
R410a 60 Hz
Sink Data (Outdoor Loop)
Page 41
001200MAN-05
CAPACITY RATINGS (continued)
Heating Mode
R-80-HACW-P-1S
Source Data (Outdoor Loop)
Nominal 6 ton
Power Consumption
ELT
Evap.
Temp
Flow
LLT
Delta T
HAB
Compressor
Fan*
°F
°C
°F
°C
USGPM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
Watts Amps
Watts
Watts
25.0
15
16.8
19.9
5.1
40,320
4,366 23.5
661
4,869
-3.9
-9.4
1.060
-6.7
2.8
11,814
31.0
20
16.8
25.3
5.7
45,235
-0.6
-6.7
1.060
-3.7
3.1
13,254
37.0
25
16.8
30.7
6.3
50,440
2.8
-3.9
1.060
-0.7
3.5
14,779
43.0
30
16.8
36.2
6.8
53,978
6.1
-1.1
1.060
2.4
3.8
15,815
48.0
35
16.8
41.2
6.8
57,024
8.9
1.7
1.060
5.1
3.8
16,708
54.0
40
16.8
46.5
7.5
62,791
12.2
4.4
1.060
8.1
4.2
18,397
60.0
45
16.8
51.8
8.2
68,924
15.6
7.2
1.060
11.0
4.6
20,195
66.0
50
16.8
57.0
9.0
75,450
18.9
10.0
1.060
13.9
5.0
22,107
4,449 23.8
661
EAT
Cond.
Temp.
Air
Flow
LAT
Delta T
Net
Output
W/W
°F
°C
°F
°C
CFM
L/s
°F
°C
°F
°C
BTU/Hr
Watts
3.41
68
98
2,400 92.8
24.8
56,598
20.0
36.7
1,133 33.8
13.8
16,583
Effective COPh
4,951
3.66
4,531 24.2
661
5,033
3.92
4,649 24.5
661
5,151
4.05
4,830 25.1
661
5,365
4.10
4,908 25.5
661
5,444
4.36
4,985 25.8
661
5,520
4.64
5,058 26.1
661
5,594
R410a 60 Hz
Sink Data (Indoor Loop)
4.94
68
100
2,400 95.1
27.1
61,795
20.0
37.8
1,133 35.1
15.1
18,106
68
102
2,400 97.5
29.5
67,279
20.0
38.9
1,133 36.4
16.4
19,713
68
104
2,400 99.2
31.2
71,219
20.0
40.0
1,133 37.4
17.4
20,867
68
107
2,400 100.9
32.9
75,029
20.0
41.7
1,133 38.3
18.3
21,983
68
109
2,400 103.6
35.6
81,064
20.0
42.8
1,133 39.8
19.8
23,752
68
111
2,400 106.4
38.4
87,458
20.0
43.9
1,133 41.3
21.3
25,625
68
113
2,400 109.3
41.3
94,236
20.0
45.0
1,133 43.0
23.0
27,611
* @ 49.7Pa (0.20inH2o) Ext. Static
Compressor: ZP70KWE-PFV
Cooling Mode
R-80-HACW-P-1S
Source Data (Indoor Loop)
EAT
Evap.
Airflow
Temp
LAT Delta T Latent Sensible
°F
°C
BTU/Hr BTU/Hr
Watts
Watts
Power Consumption
HAB
Compressor
°F
°C
°F
°C
CFM
L/s
°F
°C
80.6
44.5
2,400
56.4
24.2 29,318 60,890 90,208 3,081 17.6
BTU/Hr
Watts
27.0
6.9
1,133
13.6
13.4 8,590 17,841 26,431
45.1
2,400
56.6
24.0 29,075 60,387 89,462 3,293 18.5
27.0
7.3
1,133
13.7
13.3 8,519 17,693 26,212
80.6
45.8
2,400
56.8
23.8 28,842 59,903 88,744 3,512 19.5
27.0
7.7
1,133
13.8
13.2 8,451 17,551 26,002
80.6
46.5
2,400
57.2
23.4 28,443 59,074 87,517 3,790 20.5
ELT
Cond.
Temp.
Flow
LLT
Watts
EER
COPc
°F
°C
°F
°C
USGPM
L/s
°F
°C
710
3,611
25.0
47
75
16.8
7.32
8.3
23.9
710
3,823
23.4
52
80
6.86
710
4,041
22.0
6.43
27.0
8.1
1,133
14.0
13.0 8,334 17,308 25,642
80.6
47
2,400
57.2
23.4 27,062 58,850 85,912 4,088 21.6
27.0
8.4
1,133
14.0
13.0 7,929 17,243 25,172
710
4,319
20.3
710
4,642
18.5
5.94
5.42
80.6
48
2,400
57.6
23.0 26,694 58,048 84,742 4,353 22.7
27.0
8.8
1,133
14.2
12.8 7,821 17,008 24,829
80.6
48
2,400
58.0
22.6 26,222 57,022 83,243 4,640 23.9
710
4,908
17.3
5.06
27.0
9.1
1,133
14.4
12.6 7,683 16,707 24,390
80.6
49
2,400
58.4
22.2 25,700 55,887 81,587 4,950 25.3
27.0
9.4
1,133
14.7
12.3 7,530 16,375 23,905
710
5,194
16.0
710
5,504
14.8
4.70
4.34
11.1 26.7
57
85
13.9 29.4
62
90
16.7 32.2
71
95
21.7 35.0
76
100
24.4 37.8
81
105
27.2 40.6
86
110
30.0 43.3
6.8
30,224
6.8
30,142
7.1
29,970
7.1
29,892
93.7 12.7 101,503
1.060 34.3
16.8
30,215
88.8 12.8 102,023
1.060 31.5
16.8
6.8
83.8 12.8 102,288
1.060 28.8
16.8
30,222
74.3 12.3 102,874
1.060 23.5
16.8
6.8
69.3 12.3 103,154
1.060 20.7
16.8
BTU/Hr
Watts
64.3 12.3 103,125
1.060 17.9
16.8
°F
°C
59.3 12.3 103,148
1.060 15.2
16.8
Delta
Rejection
T
7.1
29,740
98.6 12.6 100,905
1.060 37.0
7.0
29,565
* @ 49.7Pa (0.20inH2o) Ext. Static
Compressor: ZP70KWE-PFV
001200MAN-05
Efficiency
Fan* Effective
Watts Amps Watts
80.6
R410a 60 Hz
Sink Data (Outdoor Loop)
Page 42
02 JAN 2014
ELECTRICAL TABLES
Table 20 - Heat Pump Electrical Information (208/230-1-60)
RLA
LRA
RLA
Outdoor
Circulators
Max A
Amps
Amps
Max Fuse/
Breaker
Amps
25
11.4
52
2.5
4.0
18.7
21.6
30
#10-2
45
18.6
82
3.5
4.0
26.9
31.6
40
#8-2
55
23.6
96
4.0
5.0
33.4
39.3
50
#8-2
65
28.6
118
5.5
5.0
39.9
47.1
60
#6-2
75
30.4
150
6.5
5.0
42.7
50.3
60
#6-2
60
#6-2
Model
Compressor
Fan
FLA
MCA
80*
35.7
148
7.0
5.0
48.5
57.4
* Models are single stage
** Three (3) wire required if connecting 115VAC circulators to the unit.
Wire
Size**
ga
Table 21 - Heat Pump Electrical Information (208-3-60)
Model
FLA
MCA
RLA
Outdoor
Circulators
Max A
Amps
59
2.5
4.0
58
3.5
4.0
Compressor
Fan
RLA
LRA
25
7.9
45
12.4
Amps
Max Fuse/
Breaker
Amps
Wire
Size**
ga
15.2
17.2
25
#10-3
20.7
23.8
30
#10-3
55
15.0
88
4.0
5.0
24.8
28.6
40
#8-3
65
19.6
123
5.5
5.0
30.9
35.8
50
#8-3
75
21.2
123
6.5
5.0
33.5
38.8
80*
25.0
149
7.0
5.0
37.8
44.1
* Models are single stage
** Four (4) wire required if connecting 115VAC circulators to the unit.
60
#6-3
60
#6-3
Table 22 - Heat Pump Electrical Information (460-3-60)
Model
Compressor
Fan
RLA
RLA
LRA
Outdoor
Circulators
Max A
Amps
Max Fuse/
Breaker
Amps
Wire
Size
ga
FLA
MCA
Amps
25
3.9
28
2.5
-
7.2
8.2
15
#12-3
45
6.4
38
3.5
-
10.7
12.3
20
#12-3
55
7.1
41
4.0
-
11.9
13.7
20
#12-3
65
8.1
52
5.5
-
14.4
16.4
25
#10-3
75
9.4
66
6.5
-
16.7
19.1
30
#10-3
80*
11.8
75
7.0
-
19.6
22.6
30
#10-3
* Models are single stage
Table 23 - Heat Pump Electrical Information (220-1-50)
RLA
LRA
RLA
Outdoor
Circulators
Max A
Amps
Amps
Max Fuse/
Breaker
Amps
25
10.3
52
2.5
4.0
17.6
20.2
30
#10-2
45*
15.0
67
3.5
4.0
23.3
27.1
40
#8-2
55*
17.7
98
4.0
5.0
27.5
31.9
50
#6-2
65*
27.3
153
5.5
5.0
38.6
45.4
60
#6-2
75*
32.9
176
6.5
5.0
45.2
53.4
80
#4-2
Model
Compressor
Fan
FLA
MCA
Wire
Size
ga
* Models are single stage
02 JAN 2014
Page 43
001200MAN-05
ELECTRICAL TABLES continued
Table 24 - Heat Pump Electrical Information (380-3-50)
Model
FLA
MCA
RLA
Outdoor
Circulators
Max A
Amps
Max Fuse/
Breaker
Amps
Wire
Size
ga
Amps
27
2.5
4.0
29
3.5
4.0
11.2
12.2
15
#14-4
13.3
14.6
20
#12-4
7.1
41
4.0
10.0
62
5.5
5.0
16.9
18.7
25
#10-4
5.0
21.3
23.8
30
#10-4
10.9
64
11.8
74
6.5
5.0
23.2
25.9
40
#8-4
7.0
5.0
24.6
27.6
40
#8-4
Compressor
Fan
RLA
LRA
25
3.9
45
5.0
55
65
75
80*
* Models are single stage
TABLE 25 - Plenum Heater Electrical Information
(230-1-60)
Nominal Actual FLA
(kW)
(kW)
(A)
5
7
10
15
20
5
7
10
15
20
001200MAN-05
20.8
29.2
41.7
62.5
83.3
MCA
(A)
26.0
36.5
52.1
78.1
104.2
(208-1-60)
Breaker Wire
(A)
Size
30
40
60
80
100
#10
#8
#6
#4
#3
Actual FLA
(kW)
(A)
3.8
5.3
7.5
11.3
15.0
18.1
25.3
36.1
54.2
72.2
(220-1-50)
MCA Breaker Wire
(A)
(A)
Size
22.6
31.6
45.1
67.7
90.3
Page 44
30
40
50
80
100
#10
#8
#6
#4
#3
Actual
(kW)
FLA
(A)
MCA Breaker Wire
(A)
(A)
Size
4.2
5.9
8.4
12.6
16.8
19.1
26.7
38.1
57.2
76.3
19.1
26.7
38.1
57.2
76.3
30
40
50
80
100
#10
#6
#6
#3
#3
02 JAN 2014
ELECTRICAL DIAGRAMS—Size 25 to 75 (208/230-1-60)
02 JAN 2014
Page 45
001200MAN-05
ELECTRICAL DIAGRAMS—Size 25 to 75 (208/230-1-60) - continued
001200MAN-05
Page 46
02 JAN 2014
ELECTRICAL DIAGRAMS—Size 80 (208/230-1-60)
02 JAN 2014
Page 47
001200MAN-05
ELECTRICAL DIAGRAMS—Size 80 (208/230-1-60) continued
001200MAN-05
Page 48
02 JAN 2014
REFRIGERATION CIRCUIT DIAGRAMS
02 JAN 2014
Page 49
001200MAN-05
REFRIGERATION CIRCUIT DIAGRAMS (continued)
001200MAN-05
Page 50
02 JAN 2014
CASE DETAILS (LEFT RETURN)—Size 25 to 75
02 JAN 2014
Front View—Left Return
Right Side View—Left Return (Size 25 & 45)
Left Side View– Left Return
Right Side View—Left Return (Size 55 to 75)
Page 51
001200MAN-05
CASE DETAILS (LEFT RETURN)—Size 25 to 75 - continued
Top View (Size 25 & 45)
Top View (Size 55 to 75)
001200MAN-05
Page 52
02 JAN 2014
CASE DETAILS (RIGHT RETURN)—Size 25 to 75
Front View—Right Return
Left Side View—Right Return (Size 25 & 45)
Right Side View– Right Return
Left Side View—Right Return (Size 55 to 75)
02 JAN 2014
Page 53
001200MAN-05
CASE DETAILS (RIGHT RETURN)—Size 25 to 75 - continued
Top View (Size 25 & 45)
Top View (Size 55 to 75)
001200MAN-05
Page 54
02 JAN 2014
CASE DETAILS (LEFT RETURN)—Size 80
Top View—Left Return
Front View—Left Return
Left Side View– Left Return
02 JAN 2014
Right Side View—Left Return
Page 55
001200MAN-05
CASE DETAILS (RIGHT RETURN)—Size 80
Front View—Right Return
Top View—Right Return
Right Side View– Right Return
Left Side View—Right Return
001200MAN-05
Page 56
02 JAN 2014
APPENDIX A - Control Board Specifications
02 JAN 2014
Page 57
001200MAN-05
APPENDIX B - ECM Fan Airflow Tables
NOMINAL AIRFLOW SETTING (MED)
STAGE 2
Model
Full
STAGE 1
Reduced*
Full
FAN ONLY (Recirculation)
Reduced*
Full
Reduced*
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
25
45
800
1200
378
566
680
1020
321
481
680
1030
321
486
578
876
273
413
448
672
211
317
381
571
180
270
55
65
75
80
1500
1900
2100
2400
708
897
991
1133
1275
1615
1785
2040
602
762
842
963
1240
1540
1660
N/A
585
727
783
N/A
1054
1309
1411
N/A
497
618
666
N/A
840
1064
1176
1344
396
502
555
634
714
904
1000
1142
337
427
472
539
-6% AIRFLOW SETTING (LOW)
STAGE 2
Model
Full
STAGE 1
Reduced*
Full
FAN ONLY (Recirculation)
Reduced*
Full
Reduced*
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
25
45
752
1128
355
532
639
959
302
453
639
968
302
457
543
823
256
388
421
632
199
298
358
537
169
253
55
65
75
80
1410
1786
1974
2256
665
843
932
1065
1199
1518
1678
1918
566
716
792
905
1166
1448
1560
N/A
550
683
736
N/A
991
1230
1326
N/A
468
581
626
N/A
790
1000
1105
1263
373
472
522
596
671
850
940
1074
317
401
443
507
+6% AIRFLOW SETTING (HIGH)
STAGE 2
Model
Full
STAGE 1
Reduced*
Full
FAN ONLY (Recirculation)
Reduced*
Full
Reduced*
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
25
45
848
1272
400
600
721
1081
340
510
721
1092
340
515
613
928
289
438
475
712
224
336
404
605
191
286
55
65
75
80
1590
2014
2226
2544
750
951
1051
1201
1352
1712
1892
2162
638
808
893
1021
1314
1632
1760
N/A
620
770
830
N/A
1117
1388
1496
N/A
527
655
706
N/A
890
1128
1400
1425
420
532
661
672
757
959
1190
1211
357
452
562
572
+12% AIRFLOW SETTING (MAX)
STAGE 2
Model
Full
STAGE 1
Reduced*
Full
FAN ONLY (Recirculation)
Reduced*
Full
Reduced*
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
CFM
L/s
25
45
896
1344
423
634
762
1142
359
539
762
1154
359
544
647
981
306
463
502
753
237
355
426
640
201
302
55
65
75
80
1680
2128
2352
2688
793
1004
1110
1269
1428
1809
1999
2285
674
854
944
1078
1389
1725
1859
N/A
655
814
877
N/A
1180
1466
1580
N/A
557
692
746
N/A
941
1192
1317
1505
444
562
622
710
800
1013
1120
1279
377
478
528
604
NOTES: Unit sizes 45 and 55 nominal value up to 0.50 inH2o, sizes 65, 75 and 80 up to 0.70inH2o
*To obtain the REDUCED airflow values use a dry contact to connect AR1 to AR2 on the terminal strip
001200MAN-05
INFORMATION TAKEN FROM DOCUMENT 000527INF-04
Page 58
02 JAN 2014
THIS PAGE INTENTIONALLY LEFT BLANK
02 JAN 2014
Page 59
001200MAN-05
LIMITED EXPRESS WARRANTY
It is expressly understood that unless a statement is specifically identified as a warranty, statements made by Maritime Geothermal Ltd., a corporation registered in New
Brunswick, Canada, (“MG”) or its representatives, relating to MG’s products, whether oral, written or contained in any sales literature, catalogue or agreement, are not express
warranties and do not form a part of the basis of the bargain, but are merely MG’s opinion or commendation of MG’s products.
EXCEPT AS SPECIFICALLY SET FORTH HEREIN, THERE IS NO EXPRESS WARRANTY AS TO ANY OF MG’S PRODUCTS. MG MAKES NO WARRANTY AGAINST
LATENT DEFECTS. MG MAKES NO WARRANTY OF MERCHANTABILITY OF THE GOODS OR OF THE FITNESS OF THE GOODS FOR ANY PARTICULAR PURPOSE.
LIMITED EXPRESS RESIDENTIAL WARRANTY - PARTS
MG warrants its Residential Class products, purchased and retained in the United States of America and Canada, to be free from defects in material and workmanship under
normal use and maintenance as follows:
(1) Air conditioning, heating and/or heat pump units built or sold by MG (“MG Units”) for five (5) years from the Warranty Inception Date (as defined below).
(2) Thermostats, auxiliary electric heaters and geothermal pumping modules built or sold by MG, when installed with MG Units, for five (5) years from the Warranty Inception
Date (as defined below).
(3) Sealed refrigerant circuit components of MG Units (which components only include the compressor, refrigerant to air/water heat exchangers, reversing valve body and
refrigerant metering device) for ten (10) years from the Warranty Inception Date (as defined below).
(4) Other accessories and parts built or sold by MG, when installed and purchased with MG Units, for five (5) years from the date of shipment from MG.
(5) Other accessories, when purchased separately, for (1) year from the date of shipment from MG.
The “Warranty Inception Date” shall be the date of original unit installation, as per the date on the installation Startup Record or six (6) months from date of unit
shipment from MG, whichever comes first.
To make a claim under this warranty, parts must be returned to MG in Petitcodiac, New Brunswick, freight prepaid, no later than ninety (90) days after the date of the failure of
the part. If MG determines the part to be defective and within MG’s Limited Express Residential Warranty, MG shall, when such part has been either replaced or repaired, return
such to a factory recognized distributor, dealer or service organization, freight prepaid. The warranty on any part repaired or replaced under warranty expires at the end of the
original warranty period.
LIMITED EXPRESS RESIDENTIAL WARRANTY - LABOUR
This Limited Express Residential Labour Warranty shall cover the labour incurred by MG authorized service personnel in connection with the installation of a new or repaired
warranty part that is covered by this Limited Express Residential Warranty only to the extent specifically set forth in the current labour allowance schedule "A" provided by MG’s
Warranty Department and only as follows:
(1) MG Units for two (2) years from the Warranty Inception Date.
(2) Thermostats, auxiliary electric heaters and geothermal pump modules built or sold by MG, when installed with MG Units, for two (2) years from the Warranty Inception Date.
(3) Sealed refrigerant circuit components of MG Units (which components only include the compressor, refrigerant to air/water heat exchangers, reversing valve body and
refrigerant metering device) for five (5) years from the Warranty Inception Date.
Labour costs are not covered by this Limited Express Residential Warranty to the extent they exceed the amount allowed under said allowance schedule, they are not
specifically provided for in said allowance schedule, they are not the result of work performed by MG authorized service personnel, they are incurred in connection with a part not
covered by this Limited Express Residential Warranty, or they are incurred more than the time periods set forth in this paragraph after the Warranty Inception Date.
This warranty does not cover and does not apply to:
(1) Air filters, fuses, refrigerant, fluids, oil.
(2) Products relocated after initial installation.
(3) Any portion or component of any system that is not supplied by MG, regardless of the cause of the failure of such portion or component.
(4) Products on which the unit identification tags or labels have been removed or defaced.
(5) Products on which payment to MG, or to the owner’s seller or installing contractor, is in default.
(6) Products subjected to improper or inadequate installation, maintenance, repair, wiring or voltage conditions.
(7) Products subjected to accident, misuse, negligence, abuse, fire, flood, lightning, unauthorized alteration, misapplication, contaminated or corrosive liquid or air supply,
operation at abnormal air or liquid temperatures or flow rates, or opening of the refrigerant circuit by unqualified personnel.
(8) Mold, fungus or bacteria damage
(9) Corrosion or abrasion of the product.
(10) Products supplied by others.
(11) Products which have been operated in a manner contrary to MG’s printed instructions.
(12) Products which have insufficient performance as a result of improper system design or improper application, installation, or use of MG’s products.
(13) Electricity or fuel, or any increases or unrealized savings in same, for any reason whatsoever.
Except for the limited labour allowance coverage set forth above, MG is not responsible for:
(1) The costs of fluids, refrigerant or system components supplied by others, or associated labour to repair or replace the
same, which is incurred as a result of a defective part covered by MG’s Limited Residential Warranty.
(2) The costs of labour, refrigerant, materials or service incurred in diagnosis and removal of the defective part, or in obtaining
and replacing the new or repaired part.
(3) Transportation costs of the defective part from the installation site to MG, or of the return of that part if not covered by
MG’s Limited Express Residential Warranty.
(4) The costs of normal maintenance.
This Limited Express Residential Warranty applies to MG Residential Class products manufactured on or after February 15, 2010. MG’S LIABILITY UNDER THE TERMS OF
THIS LIMITED WARRANTY SHALL APPLY ONLY TO THE MG UNITS REGISTERED WITH MG THAT BEARS THE MODEL AND SERIAL NUMBERS STATED ON THE
INSTALLATION START UP RECORD, AND MG SHALL NOT, IN ANY EVENT, BE LIABLE UNDER THE TERMS OF THIS LIMITED WARRANTY UNLESS THIS
INSTALLATION START UP RECORD HAS BEEN ENDORSED BY OWNER & DEALER/INSTALLER AND RECIEVED BY MG LIMITED WITHIN 90 DAYS OF START UP.
Limitation: This Limited Express Residential Warranty is given in lieu of all other warranties. If, not withstanding the disclaimers contained herein, it is determined that other
warranties exist, any such express warranty, including without imitation any express warranties or any implied warranties of fitness for particular purpose and merchantability,
shall be limited to the duration of the Limited Express Residential Warranty.
LIMITATION OF REMEDIES In the event of a breach of the Limited Express Residential Warranty, MG will only be obligated at MG’s option to repair the failed part or unit, or to
furnish a new or rebuilt part or unit in exchange for the part or unit which has failed. If after written notice to MG’s factory in Petitcodiac, New Brunswick of each defect, malfunction or other failure, and a reasonable number of attempts by MG to correct the defect, malfunction or other failure, and the remedy fails of its essential purpose, MG shall
refund the purchase price paid to MG in exchange for the return of the sold good(s). Said refund shall be the maximum liability of MG. THIS REMEDY IS THE SOLE AND
EXCLUSIVE REMEDY OF THE BUYER OR PURCHASER AGAINST MG FOR BREACH OF CONTRACT, FOR THE BREACH OF ANY WARRANTY OR FOR MG’S
NEGLIGENCE OR IN STRICT LIABILITY.
LIMITATION OF LIABILITY MG shall have no liability for any damages if MG’s performance is delayed for any reason or is prevented to any extent by any event such as, but
not limited to: any war, civil unrest, government restrictions or restraints, strikes, or work stoppages, fire, flood, accident, shortages of transportation, fuel, material, or labour, acts
of God or any other reason beyond the sole control of MG. MG EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGE IN CONTRACT, FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, OR IN TORT, WHETHER FOR MG’s NEGLIGENCE OR AS STRICT LIABILITY.
OBTAINING WARRANTY PERFORMANCE Normally, the dealer or service organization who installed the products will provide warranty performance for the owner. Should the
installer be unavailable, contact any MG recognized distributor, dealer or service organization. If assistance is required in obtaining warranty performance, write or call: Maritime
Geothermal Ltd • Customer Service • PO Box 2555 • Petitcodiac, New Brunswick E4Z 6H4 • (506) 756‐8135 • or e-mail to info@nordicghp.com NOTE: Some states or Canadian
provinces do not allow limitations on how long an implied warranty lasts, or the limitation or exclusions of consequential or incidental damages, so the foregoing exclusions and
limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state and from Canadian province to
Canadian province. Please refer to the MG Installation, Installation and Service Manual for operating and maintenance instructions.
An extended warranty option is also available. Please contact Maritime Geothermal Ltd. via the contact information in the previous paragraph for more information.
001200MAN-05
Page 60
02 JAN 2014