Radio Shack PRO-91 User`s guide

Add to my manuals
96 Pages

advertisement

Radio Shack PRO-91 User`s guide | Manualzz
20-428
PRO-2055 1,000 Channel
Triple Trunking
Mobile/Base Scanner
NOTE: Actual product may vary from the images found
in this document.
Please read this user’s guide before installing,
setting up and using your new product
www.radioshack.com
Contents
Thank you for purchasing your PRO-2055 triple trunking
scanner from RadioShack. You can mount your scanner
in a fixed position and use it as a base scanner or you can
use it as a mobile scanner by mounting it in a vehicle. No
additional hardware or add-on cards are needed. This
scanner is one of a new generation of scanners designed
to track Motorola® Type I and II (such as Smartnet®
and Privacy Plus®) and hybrid analog trunking systems,
GE-Ericsson (EDACS®) type systems, and EF Johnson
(LTR) type systems which are extensively used in many
communication systems.
user’s guide • quick start guide • preloaded data addendum
DC cable w/fuse
Scanner
Antenna
AC adapter
Mounting
bracket
Knob (2)
Rubber washer (2)
Lock washer (2)
Screw (2)
DIN sleeve and keys (2)
Rubber foot (3)
2
The Basics
contents
your scanner’s keypad
7
your scanner’s rear view
9
your scanner’s display
10
step 1: install your scanner
11
mounting your scanner in your dashboard
mobile mounting in your vehicle
using your scanner as a base station
step 2: power your scanner
from a wall outlet
through your vehicle’s ignition
from your vehicle’s cigarrette lighter
step 3: connect your scanner
connect the supplied antenna
connect an external antenna
connect an external speaker or headphones
quick start
11
12
13
14
14
15
16
17
17
17
18
20
understanding your scanner’s modes
setting up your scanner
turning on the scanner and setting squelch
3
20
29
29
The Basics
storing known frequencies into channels
CTCSS and DCS
storing trunking frequencies into channels
storing text tags
finding and storing active
frequencies
searching a preprogrammed frequency
range
band charts
searching active frequencies in a range
manually tuning a frequency
listening to the weather band
skywarn
using frequency copy
Signal Stalker II
scanning the channels
using CTCSS and DCS
deleting frequencies from channels
deleting all frequencies in a channel bank
using delay
locking out channels or frequencies
priority
changing the receive mode
using the attenuator
turning the key tone on and off
using the dimmer
changing the display contrast
cloning the programmed data
4
30
32
35
36
40
40
42
47
49
50
52
53
55
57
59
59
60
60
61
63
65
66
67
67
67
68
The Basics
trunking
69
how trunking works
setting squelch for trunking mode
programming trunking frequencies
care
69
71
71
85
replacing fuse
resetting/initializing your scanner
service and repair
birdie frequencies
85
85
86
86
specifications
88
The FCC wants you to know
91
scanning legally
91
glossary
93
FAQs (Frequenctly Asked Questions) 95
warranty
96
5
The Basics
©2005 RadioShack Corporation.
All Rights Reserved.
RadioShack, RadioShack.com. Hypersearch, Hyperscan, and Adaptaplug are
trademarks used by RadioShack Corporation.
Motorola, Smartnet, ASTRO and Privacy Plus are registered trademarks of
Motorla Inc.
EDACS is a registered trademark of MA-COM Inc.
LTR is a registered trademark of EF Johnson.
6
The Basics
your scanner’s keypad
TRUNK — stores the trunking ID code or holds
the trunking ID while scanning.
L/OUT — locks out selected channels and ID
codes, and skips specified frequencies during
a search.
CLEAR — clears an incorrect entry.
PROG — programs frequencies in selected
channels.
PWR/VOL/SQ — long knob turns OFF/ON, and
controls volume. Short knob controls squelch.
PC/IF — connect data cable for cloning or
connecting to a PC.
s — attach headphones with 1/8” jack here.
7
The Basics
FUNC — press in
combination with other keys
to perform various functions.
TUNE — Press TUNE,
PAUSE then e or d to tune
to a frequency.
ATT — Press to
activate attenuation (reduce
scanner sensitivity, block
strong signals). Press again to
deactivate attenuation.
PAUSE — pauses search
or tune operation.
DIM — adjusts the
backlight level (Light, Dark,
or OFF).
e or d — press to
scan or search in either
direction.
WX/
— scans through
the seven preprogrammed
weather channels, or jumps
to a Skywarn channel you
programmed (997-999).
PRI — turns the
priority function on or off.
TEXT — press to input text.
MODE — press to
change the receive mode.
SRCH — press to search
through search banks.
— scans
SCAN/
through the programmed
channels, or activates the
Signal Stalker II function.
MAN — press to manually
enter a channel number.
8
The Basics
Press to enter a number or a
character (in text mode).
ENT — press to
confirm frequency
and text entries.
./DELAY — press to enter a
decimal point, space, or hyphen.
Press to program delay time for a
channel/search bank.
your scanner’s rear view
RESET—
press to
reset your
scanner.
ANT — connect the
supplied antenna or an
external antenna here.
DC 13.8V — connect a
power source here.
SCREW HOLE — use to mount
the scanner in a car with some
hardware (screw not supplied).
EXT SP — connect an
external speaker here.
9
The Basics
your scanner’s display
10
The Basics
step 1: install your scanner
You can mount your trunking scanner in your vehicle,
install it for mobility, or install it as a base station.
mounting your scanner in your
dashboard
If you are unsure about how to install your scanner in
your vehicle, consult your automobile manufacturer,
dealer, or a qualified installer. Before installing, confirm
your scanner fits in the
desired mounting area and
you have all the necessary
materials. Your scanner
requires a 2 x 71/8 x 5 5/16
inch (50 x 180 x 135 mm)
mounting area.
1. Remove the four
rear screws and pull
off the black case
before installing your
scanner.
2. Install the DIN sleeve
into the opening in
your dashboard, lip
facing out.
3. Push out the top and
bottom tabs to hold
the sleeve firmly in
place.
4. Slide the scanner into the sleeve until it locks in
place.
11
The Basics
Note
To remove your scanner from the DIN sleeve,
insert the two keys straight into the scanner’s front
panel. Then, remove the scanner by pulling front
panel.
When mounting in your dashboard, you will need
to connect an external antenna and an external
speaker.
mobile mounting in your vehicle
You can mount your scanner under the dashboard, or
on top of it, using the mounting bracket.
1. Attach the three protective rubber feet to the
mounting bracket
when you use
the scanner on a
flat surface. Do
not use them
when you mount
the bracket with
screws.
2. Use the supplied
mounting
bracket as a
template to mark
positions for the
two mounting
screws.
3. At the marked
positions, drill holes slightly smaller than the
screws.
12
The Basics
4. Remove the paper backing from each washer and
stick one inside of each bracket’s ear, aligning the
washer’s hole with the bracket’s hole.
5. Attach the mounting bracket to your vehicle’s
surface using the supplied screws and lockwashers.
6. Slide the scanner into the bracket, aligning the
scanner’s holes with the holes in the bracket, and
then screw the mounting knobs into the scanner.
When drilling holes, be sure to avoid obstructions
Note
behind the mounting surface. Consult a qualified
installer if in doubt.
using your scanner as a base station
You can place your scanner on a desk, shelf, or table
to use it as a base station. Since the speaker is on
the bottom of the scanner, you may want to use the
mounting bracket to elevate your scanner off the
surface for better sound. Follow the mobile vehicle
mounting instructions above to affix your scanner to a
desk, shelf, table or other flat surface (except that the
bracket will be below the scanner).
13
The Basics
step 2: power your scanner
You can power your scanner from a wall outlet,
through your vehicle’s ignition, or from your vehicle’s
cigarette lighter.
from a wall outlet
1. Connect the tip of the supplied AC adapter to the
DC 13.8V jack at the rear of your scanner.
Note
2. Plug the AC adapter into your wall outlet.
You must use a Class 2 power source that supplies
13.8V DC and delivers at least 600mA. Its center
tip must be set to positive and its plug must fit the
scanner’s DC 13.8V jack. Using an adapter that does
not meet these specifications could damage the
scanner or the adapter.
Warning!
To prevent electric shock, do not use the AC
adapter’s polarized plug with an extension cord,
receptacle, or other outlet unless you can fully
insert the blades to prevent blade exposure.
14
The Basics
through your vehicle’s ignition
1. Disconnect the cable from the negative (-) terminal
of your vehicle’s battery.
2. Ground the black wire
of the supplied DC
power cord to your
vehicle’s chassis.
Be sure the grounding
Note
screw makes complete contact with the metal
frame of your vehicle.
3. Connect the red wire of the supplied DC power
cord to a voltage source that turns on and off with
the ignition switch, such as a spare accessory
terminal in your vehicle’s fuse box.
4. Insert the power
cord’s barrel plug
into the scanner’s
DC 13.8V jack.
5. Reconnect the cable
to the negative
(-) terminal of your
Rear View
vehicle’s battery.
You must use a power source that supplies 12V DC
Note
and delivers at least 600 mA. Its center tip must be
set to positive and its plug must fit the scanner’s
DC 13.8V jack. The supplied DC power cord meets
these specifications. Using a power cord that does
not meet these specifications could damage the
scanner or the adapter.
15
The Basics
from your vehicle’s cigarrette lighter
To power your scanner from a 12V power source in
your vehicle, such as a cigarette-lighter socket, you
need a 12V, 600 mA DC cigarette-lighter adapter (not
supplied), available at your local RadioShack store.
1. Insert the adapter’s barrel plug into the scanner’s DC
13.8V jack.
2. Plug the adapter’s other end into your vehicle’s
cigarette lighter or power socket.
When you use a cigarette-lighter adapter, you
Notes
might hear electrical noise from your engine while
scanning. This is normal.
16
The Basics
step 3: connect your scanner
connect the supplied antenna
Push the antenna onto
your scanner’s antenna
connector and rotate
until it locks into place.
Your scanner’s
sensitivity to various
frequencies depends
on its location and the antenna’s length. For best
reception, adjust the antenna’s length as follows:
Frequency
Antenna Length
25-54 MHz
Extend fully
108-174 MHz
Extend 4 segments
216-225 MHz
Extend 3 segments
225-406 MHz
Extend 2 segments
406-1300 MHz
Collapse fully
connect an external antenna
You will need to connect an external antenna when you
mount your scanner in
the dashboard of your
vehicle. You may also
want to connect an
external antenna if you
use your scanner as a
base station.
17
The Basics
Your local RadioShack store sells a variety of antennas.
Always use 50-ohm coaxial cable, such as RG-58 or
RG-8, to connect an outdoor antenna. For lengths
exceeding 50 feet, use RG-8 low-loss dielectric coaxial
cable. If your coaxial cable does not have a BNC
connector, you will also need a BNC adapter (not
supplied).
Warning!
Use extreme caution when installing or removing
an outdoor antenna. If the antenna starts to fall,
let it go! It could contact overhead power lines.
If the antenna touches a power line, touching
the antenna, mast, cable, or guy wires can cause
electrocution and death. Call the power company
to remove the antenna. Do not attempt to do so
yourself.
connect an external speaker or
headphones
When you mount your scanner in your dashboard,
you will need to connect an external speaker or
headphones.
Connect
headphones here
18
Connect external
speaker here
The Basics
listening safely
To protect your hearing, follow these guidelines when
you use headphones.
•
Adjust VOL (volume) to its lowest level before
putting on headphones. With the headphones on,
adjust VOL to a comfortable level.
•
Avoid increasing the volume once you set it. Over
time, your sensitivity to volume decreases, so
volume levels that do not cause discomfort might
damage your hearing.
•
Avoid listening at high volume levels. Prolonged
exposure to high volume levels can cause
permanent hearing loss.
traffic safety
Do not wear headphones while driving. This can create
a traffic hazard and is illegal in some areas. Even
though some headphones let you hear outside sounds
when you listen at normal levels, they still can present
a traffic hazard.
19
The Basics
quick start
To help familiarize yourself with the scanner’s
functions, keypad, and available frequencies, you can
utilize one of these four features before you begin
programming the scanner.
Signal Stalker II — searches nearby strong signals
quickly. See “Signal Stalker II”.
Preprogrammed Search Banks — allow you to listen to
frequencies and decide which frequencies you want to
store when you are ready to program the scanner. See
“Searching a Preprogrammed Frequency Range”.
Manual Tuning — allows you to manually move
through the entire range of available frequencies. (See
“Specifications” for a list of the available frequency
ranges.)
Weather Radio — allows you to listen to NOAA
weather broadcasts without programming. See
“Listening to the Weather Band”.
understanding your scanner’s modes
You can program each channel with any of seven
receive modes (AM, FM, CT, DC, MO, ED, and LT).
Each receive mode affects how your scanner operates
when scanning and receiving transmissions.
Note
Trunked modes (MO, ED and LT) can only be
selected for frequencies above 137 MHz.
Your scanner’s closed mode lets you hear only
those trunking talkgroups you specify. For more
information, see “Open and Closed Modes”.
20
The Basics
AM mode
The AM mode sets the scanner to receive
transmissions using amplitude modulation (AM),
primarily used for aircraft, military, some amateur
radio, and some government transmissions. (Refer to
“Specifications” for a list of the frequencies covered.)
When the scanner receives a transmission on a
channel set to the AM mode, it always stops on the
transmission.
FM mode
The FM mode sets the scanner to receive transmissions
using frequency modulation (FM), used for most public
safety transmissions, as well as broadcast, business,
and amateur radio transmissions. When the scanner
receives a transmission on a channel set to the FM
mode, it always stops on the transmission.
CTCSS (CT) mode
CTCSS mode sets the scanner to receive transmissions
using frequency modulation (FM) with Continuous
Tone Coded Squelch System (CTCSS) subaudible
tone codes. CTCSS allows multiple users to share a
single radio frequency without hearing each other’s
transmissions. CTCSS mode also features a Code
Search setting that allows you to instantly display and
store unknown codes into the channel memory. CTCSS
tones can sometimes be heard as a low “hum” in the
background of a voice transmission.
21
The Basics
DCS (DC) mode
DCS mode sets the scanner to receive transmissions
using frequency modulation (FM) with Digital Coded
Squelch (DCS) subaudible data signaling. DCS is
very similar to CTCSS, except that a digital code is
transmitted instead of an audio tone. Like CTCSS, DCS
allows multiple users to share a single radio frequency
without hearing each other’s transmissions. DCS mode
also features a Code Search setting that allows you
to instantly display and store unknown codes into the
channel memory. DCS data can sometimes be heard
as a low “purring” sound in the background of a voice
transmission. Some DCS systems transmit a special
“turn off code” at the end of each transmission. The
turn off code causes a properly equipped receiver to
mute before the transmission ends, eliminating the
“squelch tail” burst of noise the commonly occurs
when the signal is lost.
Motorola mode
You can set your scanner so it decodes the talk group
IDs used with Motorola trunking systems. This setting
is called the Motorola mode.
Motorola systems are trunking systems used primarily
by business and public safety groups to efficiently
allocate a small number of frequencies (as few as
five) to many groups of users (as many as several
thousand). To do this, each group of users in the
system is assigned to a specific talk group. For
example, the east side patrol officers might all be
assigned to talk group 2160. One channel in the system
is continuously transmitting data that identifies which
talk groups are active on which channel. In addition,
22
The Basics
this talk group information is also transmitted as
subaudible data on each active channel.
When the scanner receives a transmission on a channel
set to the Motorola mode, it first decodes the talk
group ID data included with the transmission. In the
open mode, the scanner stops on the transmission
and displays the talk group ID on the bottom line of
the display. In the closed mode, the scanner only stops
on the transmission if the talk group ID matches a talk
group ID that you have stored in the bank’s talk group
ID list and have not locked out.
Motorola trunking systems come in three categories:
Type I, Type II, and Type I/II Hybrid. Each category
displays and uses talk group IDs in slightly different
ways.
Motorola Type II IDs are in the form FFF-SS, where;
FFF=Fleet ID
SS=Subfleet ID
Type I systems are usually organized with different user
groups assigned to different fleets.
Note
For example, a valid fleet-subfleet ID identifying
all detectives within a police department might be
000-12, where 000 identifies all police users and 12
identifies the Detective division.
Tuning the scanner to an active control channel
while in Motorola mode will display the Motorola
System. ID and the approximate control channel
message decode success rate. This information can
help you identify the Motorola trunking system that
you are monitoring and the receive quality of the
control channel signal.
23
The Basics
To properly map the raw Type I data to the correct
fleet-subfleet format, you must program the correct
fleet map into the scanner. Fleet map information
is widely available on the Internet for most Type I
systems in use.
Type II system talk groups are identified by a 5-digit
number. Valid talk group IDs are divisible by 16. If you
try to enter an invalid talk group ID, the scanner rounds
the ID down to the next valid ID.
Type I/II hybrid systems use both fleet-subfleet and
5-digit formats for talk group IDs.
Note
If the scanner decodes control channel data while
receiving transmissions from a Motorola trunking
system, CNTRL appears on the bottom line of the
display.
EDACS mode
You can set your scanner so it decodes the talk group
IDs used with EDACS (GE/Ericsson) trunking systems.
This setting is called the EDACS mode.
EDACS systems are trunking systems used
primarily by business or private communications
service providers, as well as by some public safety
organizations. EDACS systems transmit active talk
group information only on a dedicated control channel.
EDACS frequencies are organized in a specific order.
Each frequency is assigned a Logical Channel Number
(LCN). For the scanner to correctly switch to an active
frequency, you must program the frequencies in LCN
order, starting with Memory 01. EDACS talk group IDs
are entered as a 4-digit decimal number from 0001 to
2047 or AFS (Agency Fleet Subfleet) number from 00001 to 15-157.
24
The Basics
When there is activity on an EDACS system, that
information is sent out on the control channel. The
scanner decodes the ID for the active talk group. In the
open mode, the scanner then goes to the transmission
and displays the talk group ID on the bottom line of the
display. In the closed mode, the scanner only goes to
transmissions with IDs that match talk group IDs you
have stored in the bank’s talk group ID list which are
not locked out.
Because EDACS scanning requires clear reception of
the control channel at all times, EDACS systems tend
to have a smaller usable area. An external antenna can
greatly improve EDACS scanning in a fringe area. If
you are having trouble scanning an EDACS system, try
manually selecting the data channel. If you are getting
good reception, the scanner will indicate talk group
CTL-01. Try changing your location or using an outdoor
antenna to improve reception.
LTR mode
You can set your scanner so it decodes the talk group
IDs used with LTR systems. This setting is called the
LTR mode.
LTR frequencies are organized in a specific order.
Each frequency is assigned a Home Repeater Number
(HR). For the scanner to correctly switch to an active
frequency, you must program the frequencies in HR
order, starting with Memory X01 in the selected bank.
Your PRO-2055 scanner features a new tool to help
you determine the correct channel mapping for LTR
system frequencies. The scanner’s LTR Repeater Finder
displays the current Home Repeater when monitoring
LTR transmissions in manual mode.
25
The Basics
To determine the correct Home Repeater programming,
enter the system channels of an LTR system in any
order. Be sure to program the mode for each LTR
channel to LT. Listen to each channel one at a time
in manual mode and watch for the decoded LTR
data at the bottom of the scanner’s display. When
an LTR transmission occurs, you should see the LTR
talkgroup information on the bottom line of the display,
and a number preceded by “R” in the bottom right
hand corner (i.e., R12). The “R” number is the Home
Repeater number that the current transmission is
occurring on. To correctly program this Home Repeater
number into your scanner, be sure that the channel
number in the bank is equal to the number that is
displayed after the “R”. For example, if you see R12
displayed on a particular LTR frequency, that frequency
needs to be programmed into Channel 12 of the
current bank in order to track the LTR system activity
properly.
LTR systems are trunking systems used primarily by
business or private communications service providers,
such as taxicabs, delivery trucks, and repair services.
These systems encode all trunking information
as digital subaudible data that accompanies each
transmission. Users on an LTR system are assigned to
specific talk groups, which are identified by the radio
as six-digit numbers. These numbers are in the form
AHHUUU, where:
A = Area code (0 or 1)
H = Home repeater (01 through 20)
U = User ID (000 through 254)
When the scanner receives a transmission on a channel
set to the LTR mode, it first decodes the LTR data
included with the transmission. In the open mode,
the scanner stops on the transmission and displays
26
The Basics
the talk group ID on the bottom line of the display.
In the closed mode, the scanner only stops on the
transmission if the LTR data matches a talk group ID
that you have stored in the bank’s talk group ID list and
have not locked out.
LTR systems are frequently programmed so that each
radio has a unique ID code.
open and closed modes
You can set your scanner to change the way it receives
signals. These settings, called open mode and closed
mode, affect how the scanner receives signals from
communications systems that use some type of closed
squelch (such as Motorola, EDACS, and LTR systems).
Note
In open mode, you hear all active talk groups
except those you specifically exclude, making it
easy to hear everything going on. In closed mode,
you hear only those talk groups you specify. This
makes it easy to listen only to talk groups you are
interested in and exclude others.
When you select a system voice channel manually,
any transmission opens squelch, regardless of the
current mode.
When no ID code is programmed into the
scanner, it receives the signal in MO, ED, or LT
mode. In open mode, the scanner stops on any
transmission. If the ID is stored, the text tag
appears on the display. Otherwise, the talk group
ID appears on the display. In closed mode, the
scanner only stops on a transmission if the ID is
stored.
You can set each of the scanner’s channel storage
banks to open or closed mode.
27
The Basics
In open mode, the scanner scans signals transmitted in
all systems. The scanner stops on any ID code and only
uses the ID list to look up ID text tags.
In closed mode, the scanner stops only on signals that
have an ID code which is found in the ID list for the
bank. Also, the scanner scans signals transmitted only
under the following conditions:
•
When the signals are in the FM, CT, or DC mode.
•
When the signals are in the MO, ED, or LT mode
and the signal’s ID code matches the programmed
ID code
You can also select the user or talk groups you want
the scanner to receive in closed mode.
When you set a channel storage bank to open mode,
+ appears under the bank’s number while scanning.
When you set a channel storage bank to closed mode,
- appears under the channel storage bank’s number
while scanning. OPEN or CLOSED appears while the
scanner is in manual mode or while the scanner is
receiving a signal during scanning. See “Changing the
Open/Closed Mode” for more information about setting
the open and closed modes.
28
The Basics
setting up your scanner
turning on the scanner and setting
squelch
1. To turn on the scanner, turn VOL clockwise. Multisystem Trunking Scanner appears. After about 3
seconds, you might hear a hissing sound. Then
adjust VOL to a comfortable level.
2. Turn SQ fully counterclockwise, then turn SQ
clockwise until the hissing sound stops.
3. To turn off the scanner, turn VOL counterclockwise
to OFF.
The scanner does not scan if there are no
Note
frequencies stored in channels. If the scanner does
not scan and you have already stored frequencies
in channels, turn SQ further clockwise.
If the scanner picks up unwanted, partial, or very
weak transmissions, turn SQ clockwise to decrease
the scanner’s sensitivity to these signals. If you
want to listen to a weak or distant station, turn SQ
counterclockwise.
If SQ is adjusted so you always hear a hissing
sound, the scanner will not scan properly.
To ensure the scanner operates properly while in
the trunking mode, we suggest you set SQ using
the steps listed above.
If SQ is adjusted precisely at the threshold where
the hissing sound stops, the radio will be most
sensitive to very weak signals. The radio may also
receive unwanted noise or signals that are too
29
The Basics
weak to understand. Most users prefer to position
the squelch control a little bit past the point of
threshold to avoid receiving noise or signals that
are too weak to understand.
storing known frequencies into
channels
Good references for active frequencies are
RadioShack’s Police Call, Aeronautical Frequency
Directory, and Maritime Frequency Directory. We
update these directories every year, so be sure to get a
current copy.
Follow these steps to store frequencies into channels.
Note
If you are storing frequencies for an EDACS
system, you must store them in order, with the
first frequency in channel 1 for the current bank.
For example, if you want to store frequency of
150.0000, 150.0125, 150.0250, and 150.0375 MHz,
you must store them in Channels 1, 2, 3, and 4
respectively.
When M appears on the display, you can use FUNC
and the arrow keys to select your desired bank and
channel number.
1. Press MAN, enter the bank (0-9) and channel number
(00-99) where you want to store a frequency, then
press MAN again. M and the bank and channel
number appear at the upper left corner of the
display (for example: M000).
30
The Basics
Note
Press FUNC. Then press e or d. The bank number
moves in the direction of the arrow pressed.
Press FUNC. Then hold down e or d. The bank
number moves continuously in the assigned
direction.
Press e. The channel number moves upward one
by one. Or, press d. The channel number moves
downward one by one.
2. Press PROG. M changes to P.
3. Use the number keys and ./DELAY to enter the
frequency (including the decimal point) you want
to store.
If you make a mistake, press CLEAR to delete a single
digit or press and hold CLEAR about 2 seconds to
delete all digits.
4. Press ENT to store the frequency into the channel.
If you made a mistake in Step 3, Invalid Freq.
Note
briefly appears and the scanner beeps when you
press ENT. Start again from Step 3.
Your scanner automatically rounds the entered
frequency to the nearest valid frequency. For
example, if you enter a frequency of 151.553, your
scanner accepts it as 151.550.
All scanners tune by steps. Your RadioShack
scanner uses steps consistent with the latest US or
worldwide standards. If you enter a non-valid step
frequency, any scanner will tune to the next step.
Some scanner designs do this without showing
the correct step in the display. This scanner will
show the actual tuned frequency in the display.
Because steps are so close together, the audio
31
The Basics
quality will not be affected by the offset.
After a transmission, the scanner automatically
pauses for 2 seconds on this channel before
proceeding to the next active transmission. Press
./DELAY to turn the delay function off or on. See
“Using Delay”. The scanner stores this setting in
the channel.
5. If necessary, press MODE to change the receiving
mode.
6. If desired, program a text tag for the channel (see
“Assigning a Text Tag to a Channel”).
7. The next channel in sequence is ready for
programming. Press PROG then repeat steps 3
through 6.
CTCSS and DCS
CTCSS and DCS allow you to program frequencies into
your scanner that are used by more than one group in
your area and listen only to the group that is of interest
to you by specifying the group’s specific CTCSS or
DCS code. CTCSS and DCS can also help reduce
instances where interfering signals cause your scanner
to stop on one channel.
There are two ways you can program your scanner to
operate with CTCSS and DCS. If you know the CTCSS
or DCS code that is used on a particular frequency,
you can manually enter the code when you are
programming the scanner, or any time afterwards.
You can also set a special search code up that will
instantly decode the CTCSS or DCS code on a received
transmission. Channels programmed with the search
32
Beyond the Basics
code will receive all traffic on the channel, and will
instantly decode and display any CTCSS or DCS code
that is found with the transmission. You can then
store the found code in the channel memory with one
keystroke.
This section of the manual describes the process for
configuring a memory channel for CTCSS or DCS
operation and manually programming a known code.
For more information on using the CTCSS and DCS
feature while scanning, see “Using CTCSS and DCS”.
To program channel memories for CTCSS or DCS
operation, follow these steps:
1. First, enter a conventional frequency. See “Storing
Known Frequencies into Channels”.
2. Once you have entered the frequency, press MODE
until the desired mode appears in the upper left
hand corner of the display. Use CT for CTCSS, and
DC for DCS.
3. By default, the search code (indicated with Code
Search in the bottom of the display) is programmed.
To program a specific code, press FUNC, MODE, and
then use the arrow keys to scroll to the desired
CTCSS or DCS code. You can also use the keypad
to enter the code manually. Note that the scanner
will automatically fill the code field as you enter the
code.
4. Once the desired code is selected, press ENT to
store the code in the channel memory.
5. It is possible to program memory channels for
CTCSS or DCS operation at any time. Simply place
33
Beyond the Basics
the scanner in program mode, navigate to the
channel you wish to change, and follow the steps
above.
6. When stopped on an active conventional channel
while scanning, you can press MODE to cycle
through the valid modes for that channel, including
CTCSS and DCS. This will reset any stored CT
or DC code to the search code, allowing you to
easily check for other CT or DC codes that may be
present on the frequency.
CTCSS, DCS and digital voice all operate
Note
independently of each other. If a channel is
configured for CTCSS or DCS, it will not be able to
decode digital transmissions. Use the FM mode
when mixed analog and digital voice reception is
desired.
CTCSS Code Table:
67.0 Hz
94.8 Hz
131.8 Hz
171.3 Hz
203.5 Hz
69.3 Hz
97.4 Hz
136.5 Hz
173.8 Hz
206.5 Hz
71.9 Hz
100.0 Hz
141.3 Hz
177.3 Hz
210.7 Hz
74.4 Hz
103.5 Hz
146.2 Hz
179.9 Hz
218.1 Hz
77.0 Hz
107.2 Hz
151.4 Hz
183.5 Hz
225.7 Hz
79.7 Hz
110.9 Hz
156.7 Hz
186.2 Hz
229.1 Hz
82.5 Hz
114.8 Hz
159.8 Hz
189.9 Hz
233.6 Hz
85.4 Hz
118.8 Hz
162.2 Hz
192.8 Hz
241.8 Hz
88.5 Hz
123.0 Hz
165.5 Hz
196.6 Hz
250.3 Hz
91.5 Hz
127.3 Hz
167.9 Hz
199.5 Hz
254.1 Hz
34
Beyond the Basics
DCS Code Table:
006
050
125
174
255
343
445
526
703
007
051
131
205
261
346
446
532
712
015
053
132
212
263
351
452
546
723
017
054
134
214
265
356
454
565
731
021
065
141
223
266
364
455
606
732
023
071
143
225
271
365
462
612
734
025
072
145
226
274
371
464
624
743
026
073
152
243
306
411
465
627
754
031
074
155
244
311
412
466
631
032
114
156
245
315
413
503
632
036
115
162
246
325
423
506
654
043
116
165
251
331
431
516
662
047
122
172
252
332
432
523
664
storing trunking frequencies into
channels
1. Press PROG and FUNC then e or d to select the
desired bank to program.
2. Press TRUNK to enter into trunking mode.
3. Repeatedly press MODE to select Motorola, EDACS,
or LTR.
4. Press PROG and select the channel number using e
or d.
35
Beyond the Basics
5. Enter the UHF trunking frequency and press ENT.
6. Repeat Steps 4 and 5 to enter the other trunking
group frequencies for EDACS or additional control
channel frequencies for Motorola systems.
7. If necessary, press MODE to change the receiving
mode.
storing text tags
You can customize your scanner by storing text tags
(up to 16 characters) for easy identification of channel
transmissions, trunk IDs, or banks.
assigning a text tag to a channel
1. Press MAN, enter the channel number where you
want to enter the text, then press MAN again. M and
the bank and channel number appear at the upper
left corner of the display (for example: M100).
2. Press PROG. M changes to P.
3. Press TEXT. The cursor appears at the third line.
4. Enter the text using the numeral keys (see “Text
Input Chart”).
If you make a mistake, press e or d to move to the
Note
character you want to change.
For example, to identify amateur (ham) radio
transmissions in the 6 meter range, input “HAM
6m” as follows:
36
Beyond the Basics
• “H” is the second letter associated with 4 on the
keypad. Press 4 then 2.
• “A” is the first letter associated with 2 on the
keypad. Press 2 then 1.
• “M” is the first letter associated with 6 on the
keypad. Press 6 then 1.
• A space is entered by pressing ./DELAY.
• “6” is the sixth number associated with 1 on the
keypad. Press 1 then 6.
• “m” is the first letter associated with 6 on the
keypad. Press 6 and FUNC (for the lower case set),
then press 1.
5. Press ENT to input the text.
assigning a text tag to a group ID
1. Press PROG.
2. Press TRUNK.
3. Press FUNC then e or d to select the desired bank.
4. Press TRUNK to select the desired sub-bank.
5. Press or hold down e or d to select the desired
group ID.
6. Press TEXT then enter the tag using the keypad. (See
“Text Input Chart”).
7. Press ENT to store.
37
Beyond the Basics
assigning a text tag to a bank
1. Press PROG.
2. Press FUNC then press bank number. Bank X (0 through
9) selected. Fn+CLR to delete all frequencies, TEXT to edit tag
appears.
3. Press TEXT, then enter the text using the keypad.
4. Press ENT to store.
text input chart
Notes
To access the numbers, after you press TEXT (when
you assign the text tag to a channel) or you press
FUNC and bank number (when you assign the text
tag to a bank), press 1. Then press the desired
number you want to enter.
To enter lowercase character or a character from
the second set for the key 0, press FUNC after
pressing the first numeral key.
PRESSED
CHARACTERS
1
0123456789
2
ABC
2 then FUNC
abc
3
DEF
3 then FUNC
def
4
GHI
4 then FUNC
ghI
5
JKL
5 then FUNC
jkl
38
Beyond the Basics
6
MNO
6 then FUNC
mno
7
PQRS
7 then FUNC
pqrs
8
TUV
8 then FUNC
tuv
9
WXYZ
9 then FUNC
wxyz
0
.-#_@+*&/,
0 then FUNC
$%!^()?~‘∆
•/DELAY
Space
CLEAR
Back Space
39
Beyond the Basics
finding and storing active
frequencies
You can search for transmissions in the scanner’s
preprogrammed search bank. The search bank is
divided into seven search bands. You can change the
search range of Bank SR6 manually by setting the
lower and higher ends of the search range.
Note
You can use the scanner’s delay feature while
searching the search bank. See “Using Delay”.
The scanner does not search locked-out
frequencies while searching ranges. See “Locking
Out Channels or Frequencies”.
searching a preprogrammed
frequency range
The scanner contains these preprogrammed search
ranges, stored in the search bank (SR0-SR6).
Bank
Band
SR0
Marine
SR1
CB
SR2
FRS/GMRS/MURS
SR3
Police/Fire
SR4
Aircraft
SR5
Amateur Bands
SR6
Limit search (User
changeable)
40
Beyond the Basics
Follow these steps to select preprogrammed search
bands and search them for active frequencies:
1. Repeatedly press SRCH to select your desired search
bank (SR0, SR1, SR2, SR3, SR4, SR5, or SR6).
2. In the marine, CB, and FRS/GMRS/MURS bands,
you can directly select a channel or search through
the band. When MAN appears at the right of the
third line, you can directly select a channel (refer to
“Band Charts”). Press the desired channel number
while MAN appears to select it. You can also change
the channels by pressing e or d.
3. Press FUNC then SRCH while MAN appears. MAN
changes to SRCH and now you can search through
the band. Press FUNC then SRCH again to return to the
previous mode.
4. Rotate SQ clockwise and leave it set to a point just
after the rushing sound stops. After 2 seconds
(if the delay feature is on), the scanner starts
searching.
5. When the scanner finds an active frequency, it
stops searching.
41
Beyond the Basics
band charts
search bank: SR0 marine band
Two frequencies are assigned in one channel in
some Marine frequencies. For example, 157.000
and 161.600 are assigned in Channel 20.
Note
Receive mode: FM
Ch.
Frequency
(MHz)
Ch.
Frequency
(MHz)
01
156.0500
05
156.2500
06
156.3000
07
156.3500
08
156.4000
09
156.4500
10
156.5000
11
156.5500
12
156.6000
13
156.6500
14
156.7000
15
156.7500
16
156.8000
17
156.8500
18
156.9000
19
156.9500
20
157.0000
161.6000
21
157.0500
22
157.1000
23
157.1500
24
157.2000
161.8000
25
157.2500
161.8500
26
157.3000
161.9000
27
157.3500
161.9500
28
157.4000
162.0000
63
156.1750
64
156.2250
160.8250
65
156.2750
42
Beyond the Basics
66
156.3250
67
156.3750
68
156.4250
69
156.4750
70
156.5250
71
156.5750
72
156.6250
73
156.6750
74
156.7250
77
156.8750
78
156.9250
79
156.9750
80
157.0250
81
157.0750
82
157.1250
83
157.1750
84
157.2250
161.8250
85
157.2750
161.8750
86
157.3250
161.9250
87
157.3750
161.9750
88
157.4250
Frequency
(MHz)
Search bank: SR1 CB band
Receive mode: AM
Ch.
Frequency
(MHz)
Ch.
01
26.9650
02
26.9750
03
26.9850
04
27.0050
05
27.0150
06
27.0250
07
27.0350
08
27.0550
09
27.0650
10
27.0750
11
27.0850
12
27.1050
13
27.1150
14
27.1250
15
27.1350
16
27.1550
17
27.1650
18
27.1750
19
27.1850
20
27.2050
43
Beyond the Basics
21
27.2150
22
27.2250
23
27.2550
24
27.2350
25
27.2450
26
27.2650
27
27.2750
28
27.2850
29
27.2950
30
27.3050
31
27.3150
32
27.3250
33
27.3350
34
27.3450
35
27.3550
36
27.3650
37
27.3750
38
27.3850
39
27.3950
40
27.4050
Search bank: SR2 FRS/GMRS/MURS
Receive Mode: FM
Ch.
Frequency
(MHz)
Ch.
Frequency
(MHz)
01
462.5625
02
462.5875
03
462.6125
04
462.6375
05
462.6625
06
462.6875
07
462.7125
08
467.5625
09
467.5875
10
467.6125
11
467.6375
12
467.6625
13
467.6875
14
467.7125
15
462.5500
16
462.5750
17
462.6000
18
462.6250
19
462.6500
20
462.6750
21
462.7000
22
462.7250
23
151.8200
24
151.8800
44
Beyond the Basics
25
151.9400
27
154.6000
26
154.5700
Search bank: SR3 Police/Fire band
Receive Mode: FM
Group
0
Frequency
(MHz)
Step (kHz)
33.420 – 33.980
20
37.020 – 37.420
20
39.020 – 39.980
20
42.020 – 42.940
20
44.620 – 45.860
40
45.880
45.900
1
45.940 – 46.060
40
46.080 – 46.500
20
153.770 – 154.130
60
154.145 – 154.445
15
154.650 – 154.950
15
155.010 – 155.370
60
155.415 – 155.700
15
155.730 – 156.210
60
158.730 – 159.210
60
166.250
170.150
45
Beyond the Basics
2
3
453.0375
– 453.9625
12.5
458.0375
– 458.9625
12.5
460.0125
– 460.6375
12.5
465.0125
– 465.6375
12.5
851.0125
– 860.9875
25
866.0125
– 868.9875
12.5
Search bank: SR4 Aircraft
Receive mode: AM
Note
Frequency (MHz)
Step (kHz)
108.000 – 136.99166
8.33
All scanners tune by steps. Your RadioShack
scanner uses steps consistent with the latest US or
worldwide standards. If you enter a non-valid step
frequency, any scanner will tune to the next step.
Some scanner designs do this without showing
the correct step in the display. This scanner will
show the actual tuned frequency in the display.
Because steps are so close together, the audio
quality will not be affected by the offset.
46
Beyond the Basics
Search bank: SR5 Ham band
Receive mode: FM
Group
Frequency (MHz)
Step (kHz)
0
28.0000 – 29.7000
5
1
50.0000 – 54.0000
5
2
144.0000 – 148.0000
5
3
222.0000 – 225.0000
5
4
420.0000 – 450.0000
12.5
5
1240.0000 – 1300.0000
6.25
search bank: SR6 programmable limit search
Receive mode: FM or AM (Default setting)
searching active frequencies in a
range
You can program the desired frequency range for a
search.
1. Repeatedly press SRCH to select SR6.
2. Press PROG then SRCH. Enter SR6 Search Range Limits:
appears and the cursor blinks L on the third line for
the lower-end limit frequency.
3. Use the number keys and ./DELAY to enter the
desired lower-end limit frequency (including the
decimal point).
4. Press ENT to set the frequency. The cursor moves to
U. If the entered frequency is incorrect, Invalid Freq.
briefly appears.
47
Beyond the Basics
5. Enter your desired upper-end frequency and press
ENT.
6. Press SRCH to start searching.
7. Rotate SQ clockwise and leave it set to a point just
after the rushing sound stops. When the scanner
finds an active frequency, it stops searching.
You can copy and save a frequency into a specified
Note
bank, channel, or priority channel when the
scanner finds an active frequency. See “Using
Frequency Copy” to save the frequency.
While the scanner is searching, you can use the
seek search by pressing FUNC then 7. Seek Search
ON. appears on the bottom line about 2 seconds.
When Seek Search ON. disappears, the scanner
displays S mark The scanner stops at an active
frequency for five seconds and restarts searching
automatically. The scanner repeats this operation.
You can set Zeromatic on or off by pressing FUNC then
0. Press FUNC then 0 again to reverse the Zeromatic
setting. Whenever this feature is turned on, Zeromatic
ON. briefly appears then ZM appears at the right of
the second line and the scanner stops at the correct
frequency. When you turn this feature off, ZM changes
to small caps (zm) and the scanner stops when it
detects an active signal. Zeromatic functions only in
search banks 3, 4, 5 and 6.
There are several group banks in SR3 Police/Fire and
SR5 Amateur bands. You can turn off or on the groups
by pressing the group numbers. For example to turn
off 0, press 0.
In the Air and Limit search bands, press FUNC then
press e to start searching up from the lowest
48
Beyond the Basics
frequency or press d to start searching down from the
highest frequency.
Note
If you press PAUSE while searching, the scanner
stops searching and *** PAUSED *** appears.
Press PAUSE again, and the scanner resumes
searching.
manually tuning a frequency
You can manually set the scanner to move through all
receivable frequencies, or select a specific frequency
as a starting point.
1. Press TUNE. The currently-tuned frequency , ***
PAUSED ***, and Fine Tune Mode appear.
2. Use the number keys to enter the frequency where
you want the scanner to start.
3. Press ENT.
4. Press PAUSE. The scanner starts the tune operation.
To change the tune direction, press e or d to tune
up or down. When the scanner finds an active
frequency, it stops on the frequency.
5. You can press FUNC TUNE while the scanner is
stopped on a frequency in MANUAL mode to
begin the TUNE function from that frequency. For
example, if the scanner is stopped in MANUAL
mode on channel 144 with frequency 145.31000
MHz, pressing FUNC TUNE will enter TUNE mode
and automatically set the TUNE frequency for
145.31000 MHz.
49
Beyond the Basics
listening to the weather band
The FCC (Federal Communications Commission) has
allocated channels for use by the National Oceanic
and Atmospheric Administration (NOAA). Regulatory
agencies in other countries have also allocated
channels for use by their weather reporting authorities.
NOAA and your local weather reporting authority
broadcast your local forecast and regional weather
information on one or more of these channels.
listening to a weather channel
To hear your local forecast and regional weather
information, press WX. Your scanner scans through the
weather band then stops within a few seconds on the
next available weather broadcast.
SAME standby mode
The National Weather Service precedes each weather
alert with a digitally encoded SAME (Specific Area
Message Encoding) signal, then a 1050 Hz tone. The
SAME signal includes a FIPS (Federal Information
Processing Standard) area code, and an event code
that corresponds with the type of alert being sent.
You can configure your scanner to operate in SAME
Standby mode, where it monitors a selected weather
radio station for SAME alerts for areas you specify. You
can program your scanner with up to 10 FIPS codes
for the areas you desire. The National Weather Service
maintains a current list of FIPS codes at http://www.
nws.noaa.gov/nwr/.
To configure your scanner for SAME Standby mode,
follow these steps:
50
Beyond the Basics
1. Press WX until you identify the weather station with
the strongest signal for your location.
2. Press FUNC, and then PROG to access the FIPS code
entry table.
3. Use the e or d keys to select the desired FIPS
code storage location.
Note
4. Use the numeric keys to enter the desired FIPS
code, and then press ENT to store the code. Press
TEXT to label the code entry with an alphanumeric
text table if desired. Repeat this process for all the
FIPS codes that you wish to store.
To delete a FIPS code, select it and then press FUNC
CLEAR.
5. Press L/OUT to lock out or enable specific FIPS
entries.
6. Press WX to exit the FIPS code entry table.
Press WX then a number key to quickly review
Notes
stored FIPS codes. Press L/OUT to toggle lockout
status.
Your scanner can also detect the 1050 Hz weather
alert tone when a weather channel is set as the
priority channel and weather priority operation is
enabled. (see “Priority”). In this mode all alerts are
received. FIPS settings are ignored.
The scanner sounds an alert or beep when it
receives the SAME code. If you do not stop the
alert (or beep) for five minutes, the alert stops
and the scanner beeps every ten seconds. If
the scanner receives a new message after five
minutes, it sounds the alert or beep. To stop the
sound and ready the scanner to receive a new alert
51
Beyond the Basics
signal before the five minute time out, press any
key except DIM.
7. Press FUNC, and then WX to initiate SAME standby.
The scanner will monitor the selected weather
radio station for alerts with FIPS codes that match
the codes you entered in the FIPS entry table. To
exit SAME standby, press FUNC, and then WX.
WX Alert and beep tone confirmation
1. To test the WX alert, press WX for more than 2
seconds while SAME Standby appears.
The display indicates the type of message, and the
scanner sounds an alert or series of beeps. The
beeps automatically change every 3 seconds.
2. Press any key except DIM to stop test sound mode.
Skywarn
Many areas of the country have amateur radio
repeaters that have been designated as “Skywarn”
repeaters. During times of severe weather, these
repeaters are used to relay reports of severe weather
directly to meteorologists at a local National Weather
Service (NWS) forecast office. Using the Skywarn
feature in your scanner, you can easily jump to one of
three Skywarn repeater frequencies and monitor these
reports, in many cases hearing about severe weather in
your area instantly as it occurs.
This function lets you quickly move to the skywarn
channels (channels 997 through 999) from any mode
except SAME standby by pressing and holding WX
about 1 second. The scanner displays Skywarn-1 in the
52
Beyond the Basics
fourth line. The scanner has 3 Skywarn channels. Press
e or d to select different Skywarn channels.
Note
To activate this function, you must program your
desired Skywarn frequencies into the Skywarn
channels.
using frequency copy
You can copy a frequency into a specified channel,
a vacant channel in a specified bank, or a priority
channel. However, you cannot copy a frequency from
the Marine search band.
copying a frequency into a specified channel
You can copy a frequency into a specified channel
when the scanner stops on that frequency during
search mode or manual tuning.
1. Press FUNC then PROG when you find a frequency.
Store in ChXXX ? appears on the bottom line. After
about 1 second, the frequency to be copied flashes.
2. Press the desired bank and the channel number
where you want to store the frequency. The display
indicates the bank and channel number. After about
1 second, the frequency to be copied flashes.
3. Press ENT. All the conditions such as receive
mode and delay condition are copied onto the
channel. Channel Stored! briefly appears. The scanner
automatically returns to search mode.
If you try to copy a frequency which is already stored
in the same bank, the scanner sounds the notice tone
3 times after you press ENT. Dupl.Freq. ChXXX appears.
If you want to copy the duplicate frequency anyway,
press ENT, or if not, press CLEAR to cancel.
53
Beyond the Basics
copying a frequency into an empty channel
within a bank
You can copy a frequency into a vacant channel
in a specified bank when the scanner stops on the
frequency during search or tune mode.
1. Press FUNC then ENT when you find a frequency you
want to copy. Bank 9 Store? appears.
2. If you want to copy the frequency into bank 9,
press ENT. It is stored in the first available vacant
channel in the bank. Or, press your desired bank
number to store, then press ENT. Channel Stored!
appears for 2 seconds. All the conditions such as
receiving mode and delay condition are copied on
the channel. After about 2 seconds, the scanner
automatically returns to search mode.
3. If you try to copy a frequency which is already
stored in the same bank, the scanner sounds the
notice tone 3 times after you press ENT. Dupl.Freq.
ChXXX appears on the third line. If you want to
copy the duplicate frequency anyway, press ENT, or
if not, press CLEAR to cancel.
copying a frequency into the priority channel
You can copy a frequency into the priority channel (see
“Priority”) when the scanner stops on the frequency
during Search, Scan, Manual, Tune, or WX mode.
Press FUNC then PRI when the frequency appears. The
display flashes twice and the frequency is copied to the
priority channel.
54
Beyond the Basics
Signal Stalker II
Your scanner’s Signal Stalker II feature provides a
powerful new tool for you to rapidly detect, monitor
and store frequencies for nearby radio transmissions.
The Signal Stalker II feature is similar in functionality
to portable frequency counters that cost much more
than your scanner, but provides many advantages over
typical portable frequency counters. For example:
The Signal Stalker II allows you to sweep the entire
range of your scanner’s design frequencies, or you
can specify those frequency ranges that you wish
to sweep and exclude ranges that you do not want
to sweep. This allows you to omit frequency ranges
with constant strong frequency activity, such as
those with paging or broadcast transmitters. Many
portable frequency counters will remain locked to a
nearby constant signal, such as a paging or broadcast
transmitter, and will not function properly until you
have left the vicinity of the transmitter.
The Signal Stalker II feature is more sensitive
than portable frequency counters and will detect
transmissions at a greater distance. You can activate
the Attenuator to reduce the sensitivity if desired.
Once an active frequency is found, the transmission
is played through your scanner’s speaker, and you
can quickly store it in any of your scanner’s memory
locations.
using Signal Stalker II
Your scanner’s Signal Stalker II functions when
you press and hold
for approximately 1 second.
The Signal Stalker II function can be set to watch
for activity on all band frequencies or Police/Fire
55
Beyond the Basics
frequencies only. To change the all bands to police/fire
or vice versa, press FUNC then .
You can also turn on/off frequency sub-bands using the
corresponding number keys while Signal Stalker II is
active.
Notes
Priority mode is not available while using the
Signal Stalker II.
Press FUNC then e or d, you can change the normal
Signal Stalker II operation to the Special Signal Stalker
II operation. In the Special Stalker operation, Sp.
Stalker appears and the frequency range is divided by
1 MHz segment. If you lock out 5 frequencies within a
1 MHz segment, the scanner will skip that segment in
subsequent sweeps. See “Using Signal Stalker II with
Lockout” below.
using Signal Stalker II with lockout
The scanner’s lock out feature can be used to bypass
unwanted transmissions while using the Signal Stalker
II. Press L/OUT when the scanner is stopped on an
undesired transmission. Press FUNC L/OUT to review or
clear locked out frequencies in the Signal Stalker II.
You can lock out 150 frequencies while searching all
bands and 50 frequencies while searching Police/Fire
frequencies.
Signal Stalker II functions by rapidly sweeping through
the RF spectrum in 1 MHz segments. If RF signal
energy is detected in a 1 MHz segment, Signal Stalker
II will sweep through the 1MHz segment in finer steps
until the source of the RF signal energy is found.
Certain segments of RF spectrum are used by high
power transmitters, such as paging transmitters. The
Signal Stalker II can detect these transmitters easily,
even at great distances due to their high transmitter
56
Beyond the Basics
output power. You can press L/OUT when the Signal
Stalker II stops on these undesired transmissions
to prevent the Signal Stalker II from stopping on
them in future sweeps, however, the Signal Stalker
II will still see their RF signal energy when sweeping
through the 1 MHz segment. This will cause the Signal
Stalker II to execute another fine step search of the
1 MHz segment. Of course, if you have locked out
the undesired transmissions, the Signal Stalker II will
not stop on them again, however, the overall sweep
performance of the Signal Stalker II will be impacted.
Signal Stalker II features a special lockout mode that
causes the scanner to skip a 1 MHz segment if five or
more lockouts exist in that 1 MHz segment. To activate
this mode, press FUNC e while in the Signal Stalker II
mode. If a 1 MHz segment contains 5 or more lockouts
it will be skipped entirely while Signal Stalker II is
sweeping. Use FUNC L/O to review or clear locked Signal
Stalker II frequencies.
To clear a locked-out frequency, select that frequency,
then press CLEAR.
scanning the channels
To begin scanning channels or to start scanning again
after monitoring a specific channel, press SCAN.
Notes
You must store frequencies into channels before
the scanner can scan them. The scanner does not
scan through empty channels.
To change the scanning direction, press e or d.
The scanner scans through all channels (except those
you have locked out) in the active banks (see “Turning
Channel-Storage Banks Off and On”and “Locking Out
Channels or Frequencies”).
57
Beyond the Basics
turning channel-storage banks off and on
To turn off banks while scanning, press the bank’s
number key so the bank’s number disappears. For
example, to turn off bank 1, press 1. The scanner does
not scan any of the channels within the banks you
turned off.
To turn on banks while scanning, press the number key
until the bank’s number appears. For example to turn
bank 1 on again, press 1.
Notes
You cannot turn off all banks. There must be at
least one active bank.
You can manually select any channel in a bank,
even if the bank is turned off.
monitoring a single channel/power save circuit
You can monitor a single channel with your scanner by
navigating to that channel while in manual mode. The
scanner will receive traffic on the selected frequency.
58
Beyond the Basics
using CTCSS and DCS
Your scanner’s advanced, CTCSS and DCS decoder
allows you to listen only to the group that is of interest
to you by specifying the group’s specific CTCSS or
DCS code for a certain frequency. CTCSS and DCS can
also help reduce instances where interfering signals
cause your scanner to stop on one channel.
When your scanner stops on a conventional frequency
that is configured for CTCSS or DCS, it checks for
a match between the transmitted and stored codes
match, the scanner stops on the transmission and
allows the audio to pass to the speaker. If the codes
do not match, the scanner resumes scan operation.
If the special “search” code is in use, the scanner
will instantly display any detected CTCSS code
if programmed for CTCSS mode, or DCS code if
programmed for DCS code. You can store the detected
code into the channel memory by pressing ENT while
the code is displayed.
For more information about your scanner’s receive
modes, including CTCSS and DCS, see “Understanding
Your Scanner’s Modes”. For more information on
programming memory channels for CTCSS or DCS
operation, see “CTCSS and DCS”.
deleting frequencies from channels
1. Press MAN.
2. Use the number keys to enter the channel with the
frequency you want to delete.
3. Press MAN again.
59
Beyond the Basics
4. Press PROG to enter the program mode. M changes
to P.
5. Press FUNC.
6. Press CLEAR. The frequency number changes and
0.0000 appears.
deleting all frequencies in a channel
bank
1. Press PROG.
2. Press FUNC then the bank number you want to clear.
Bank X selected. Fn+CLR to delete all frequencies. TEXT to
edit tag appears.
3. Press FUNC then CLEAR. Clear entire bank? Press 1 to clear
all, any other key aborts appears.
4. Press 1 to clear the selected bank’s all channel
memory. please stand by. appears while the scanner
clears all channel memory. Press any other than 1
to cancel clear.
using delay
Many conversations might have a pause of several
seconds between a query and a reply. To avoid missing
a reply, you can program a 2-second delay into any
of your scanner’s channels. Then, when the scanner
stops on the channel, DLY appears and the scanner
continues to monitor the channel for 2 seconds after
the transmission stops before it resumes scanning. The
delay feature is also available while searching.
60
Beyond the Basics
Notes
Delay is automatically set as the default for each
channel when you turn on the scanner.
To turn delay on or off, press ./DELAY. DLY (delay on) or
dly (delay off) appears on the display.
locking out channels or frequencies
You can scan existing channels or search frequencies
faster by locking out channels or frequencies that have
a continuous transmission, such as a weather channel.
locking out channels
To lock out a channel while scanning, press L/OUT when
the scanner stops on the channel. To lock out a channel
manually, select the channel then press L/OUT so lo
changes to LO on the display.
Note
You can still manually select locked-out channels.
To remove the lockout from a channel, manually select
the channel and press L/OUT so LO changes to lo.
reviewing locked-out channels
To review all locked out channels, press MAN. Then
repeatedly alternate between pressing FUNC and then
L/OUT to view each locked-out channel. When you finish
reviewing locked-out channels, press MAN.
locking out frequencies
To lock out a frequency during a search, press L/OUT
when the scanner stops on that frequency. The scanner
locks out the frequency, then continues searching.
Note
The scanner does not store locked out frequencies
during a search.
61
Beyond the Basics
You can lock out as many as 50 frequencies in each
bank. If you try to lock out more, L/O Memory Full!
appears.
If you lock out all frequencies in one search bank
and only this search bank is activated, All ranges
Locked out! appears and the scanner does not
search.
reviewing locked-out frequencies
To review the frequencies within a search bank that you
locked out:
1. Press SRCH to set search mode.
2. Press FUNC then L/OUT. The locked-out frequency
and Lockout list appear. Press e or d to review the
list. The locked-out number and the total lockedout number also appears as Lockout XX of YY. (The
tenth of thirty locked out number would appear as
Lockout 10 of 30). If the search bank has no lockedout frequencies, No Lockout appears. Press FUNC
then L/OUT again to cancel reviewing locked-out
frequencies.
clearing a locked-out frequency
To clear a locked-out frequency, select that frequency
(see “Reviewing Locked-Out Frequencies”), then press
CLEAR.
62
Beyond the Basics
If all locked-out frequencies are cleared within a bank,
No Lockout appears.
clearing all locked-out frequencies in a search
bank
1. Press SRCH.
2. Select the search bank in which you want to clear
all locked-out frequencies.
3. Press FUNC then press L/OUT. Lockout list appears.
4. Press FUNC then 6. Clear entire list ? Press 1 to clear all, any
other key aborts appears. Press 1 to clear all lockedout frequencies. List cleared. appears for about 2
seconds. Press any key other than 1 to cancel clear.
priority
In addition to the 1,000 programmable memory
channels, the scanner has one priority channel.
With the priority feature, you can scan through
programmed channels and still not miss an important
or interesting transmission on a specific channel. When
priority is turned on, the scanner checks that channel
every 2 seconds, and stays on the channel if there is
activity until the activity stops.
Note
The priority feature does not operate while the
scanner receives a trunking voice channel or
during trunking delay time. Therefore, the priority
check seems random during peak hours.
If you program a weather channel as the priority
channel, the scanner stays in the priority channel
63
Beyond the Basics
only when the scanner detects the weather alert
tone.
This scanner cannot set a channel as the priority
channel if the channel’s receive mode is MOT, ED,
or LTR.
If you press PAUSE while the scanner receives the
priority channel, the scanner displays *** PAUSED
*** and stays on the priority channel even after the
transmission finished.
To program a frequency in the priority channel:
1. Press MAN.
2. Use the number keys to enter the channel number
which contains the frequency you want to program
as the priority channel. Then press MAN again.
3. Press FUNC then PRI. The display blinks.
To program the priority channel directly:
1. Press PROG.
2. Press PRI.
3. Enter the frequency you want to enter into the
priority channel, then press ENT.
To program a weather channel as the priority channel:
1. Press WX.
2. Select the weather channel you want to program as
the priority channel.
3. Press FUNC then PRI. The display flashes two times.
To turn on the priority feature, press PRI so pri changes
64
Beyond the Basics
PRI on the display while scanning. If the scanner
detects activity on the priority channel, Priority Channel
appears. Or if the scanner detects a weather alert
tone in Priority WX mode, Priority Channel! appears
for 3 seconds then changes to Weather ALERT and the
scanner sounds an alert tone.
Note
Priority WX is only for receiving a weather alert.
When the scanner detects a 1050 Hz alert tone,
priority WX activates and you receive a weather
alert.
If you program a weather frequency into the
priority channel and the scanner detects a weather
alert tone on that frequency, the scanner sounds
the alert tone.
To turn off the priority feature, press PRI.
changing the receive mode
The scanner is preset to the most common AM or
FM receive mode for each frequency range. The
preset mode is correct in most cases. However, some
amateur radio transmissions and trunked systems do
not operate in the preset mode. If you try to listen to a
transmission when the scanner is not set to the correct
receive mode, the transmission might sound weak or
distorted.
If you want to listen to trunking transmissions in closed
mode, you might have to change the receive mode.
To change the receive mode, repeatedly press MODE.
The receive mode changes as follows:
AM – accesses the AM mode
FM – accesses the FM mode
CT – accesses the FM mode, CTCSS System
65
Beyond the Basics
DC – accesses the FM mode, DCS System
MO – accesses the FM Mode, Motorola Trunking
System (with 4- or 5-digit ID code)
ED – accesses the FM Mode, EDACS Trunking System
(with 4-digit decimal ID code or 5-digit AFS code)
LT – accesses the FM mode, LTR Trunking System (with
6-digit ID code)
Notes
MO (MOT), ED, and LT modes are not available
when the scanner tunes up or down through the
frequency ranges in which the trunking operation
is not used.
using the attenuator
To reduce interference or noise caused by strong
signals, you can reduce the scanner’s sensitivity to
these signals.
There are two attenuator modes in your scanner.
One is normal attenuator mode in which you set the
attenuator in each channel or each band/group in the
search and tune mode. The other is global mode in
which you set the attenuator only once. This setting is
applied all the time in every mode.
Press ATT to turn on or off the attenuator while the
channel number is indicated or while the scanner is
searching through bands/groups. When the attenuator
is on, att changes to ATT.
When you turn it off, ATT changes to att. You cannot set
the attenuator while the scanner is scanning.
Press FUNC and then ATT to set the attenuator to its
global mode. Global ATT. appears for 2 seconds at the
bottom line and atg appears. Press ATT to turn the
66
Beyond the Basics
attenuator on or off. ATG or atg appears on the second
line.
Press FUNC and then ATT again to turn off the global
attenuation mode. Normal ATT. appears on the bottom
line for about 2 seconds.
Note
If you turn on the attenuator, the scanner might not
receive weak signals.
turning the key tone on and off
Each time you press any of the scanner’s keys, the
scanner sounds a tone. To turn the scanner’s key tone
off or on:
1. If the scanner is on, turn OFF/VOL counterclockwise
until it clicks to turn the scanner off.
2. Turn OFF/VOL clockwise to turn the scanner on. Multisystem Trunking Scanner appears.
3. While Multi-system Trunking Scanner appears, press 1 to
turn on the key tone or 2 to turn it off.
using the dimmer
Repeatedly press DIM to adjust the brightness of the
display backlight to Dark, Light Off, or Light.
changing the display contrast
1. Press MAN.
2. Press FUNC then 9. Use Up/Down keys to set contrast,
ENTER key saves. appears.
67
Beyond the Basics
3. Press e or d to select the contrast.
4. Press ENT to set the display contrast.
cloning the programmed data
You can transfer the programmed data to and from
another PRO-2055 or PRO-97 scanner using an
optional connecting cable with 1/8-inch (3.5 mm)
phone plugs on both ends (not supplied, available at
your local RadioShack store).
Note
“CLONE MODE” Incorrect Model appears if the
scanner receives data from another scanner other
than a PRO-2055 or PRO-97.This scanner can
send/receive the data to or from a PRO-97 scanner.
Only the Light (PRO-97) and Dimmer (PRO-2055)
settings are not transferred, they are set to default.
1. Turn on both scanners.
2. Connect the connecting cable to each scanner’s
PC/IF jack. **CLONE MODE** Press UP to send Remove
cable to exit. appears.
3. Press e. Confirm to send data? 1 -> YES Press other key for
NO. appears.
4. Press 1 to send the data to the other unit or press
any other key to cancel the operation.
The scanner sends the data. To exit the clone mode,
remove the cable.
68
Beyond the Basics
trunking
how trunking works
The scanner tracks transmissions that use the Motorola
Type I and Type II (such as Smartnet and Privacy
Plus) and hybrid analog trunking systems, plus GE/
Ericsson (EDACS) and EF Johnson (LTR) type systems
extensively used in many communication systems.
Trunking systems allocate a few frequencies to many
different users. When the mobile unit transmits a
signal, one frequency is chosen from among the
allocated frequencies in that trunking system. The
user’s ID talk group is sent with the signal.
To receive trunking signals, you must store all the
trunking control frequencies for Motorola systems or
all the trunking group frequencies for EDACS and LTR
in one bank (see “Storing Known Frequencies into
Channels”) and input ID codes in the ID memory (see
“Storing Talk Group IDs”).
Your PRO-2055 automatically calculates Motorola
voice channel frequencies when it decodes the control
channel. This eliminates the need to enter all the
Motorola group frequencies.
The control channels are subject to change depending
on the day. Therefore enter all the control frequencies
in the same bank. If you do not know which is the
control channel, it is better to enter all the system
frequencies into the same bank.
When the scanner decodes the Motorola control
channel and finds the voice channel, the scanner
displays the control channel memory location on
the top line, the received frequency with VC (voice
channel) on the second line, the bank and control
69
Beyond the Basics
channel memory location number on the third line and
the Motorola ID number on the bottom line.
Note
To listen to the transmission, the mode of the
programmed channel must be the same as that of
the trunking channel (MO, ED, or LT).
When an ID code is received, the ID list for the bank is
searched, and if found, the text name stored for the ID
appears. If not found, scanning resumes immediately
unless the bank is in open trunking mode.
Note
There might be more than one talk group
transmitting at a time in some Motorola trunking
systems. If you set the scanner to manually tune
in Motorola trunking mode, you will hear the
talk group on that channel, but the display will
alternate between all active IDs.
Frequency fleet map and talk group information
are also widely available on the Internet (for
example, at www.trunkscanner.com).
In the past, groups that transmit frequently, such as
police departments, could transmit on only a few
frequencies. This resulted in heavy traffic and often
required 2-way radio users to wait for a specific
frequency to clear before transmitting. Trunked
systems allow more groups of 2-way radio users to
use fewer frequencies. Instead of selecting a specific
frequency to transmit on, a trunked system chooses
one of several frequencies when the 2-way radio user
transmits. The system automatically transmits the call
on that frequency, and also sends a code that identifies
that 2-way radio user’s transmission on a control
channel.
Your scanner lets you easily hear both the call and
response transmissions for that 2-way radio user and
therefore follow the conversation. For EDACS and
70
Beyond the Basics
Motorola (above 406 MHz range), the scanner monitors
the control channel between each transmission to
identify talk groups. For some Motorola (under 512
MHz range) and LTR systems, the scanner uses the
subaudible data sent with each transmission to identify
talk groups.
setting squelch for trunking mode
Your scanner automatically mutes the audio during
trunk scanning when it decodes control channel data.
However, we recommend you turn SQ clockwise and
leave it set to a point just after the rushing sound stops.
This lets the scanner quickly acquire the data channel.
programming trunking frequencies
You program trunking frequencies the same as nontrunked frequencies, except that you must store the
appropriate mode (MO, ED, or LT) with each frequency.
Note
You can scan only one type of trunked frequency,
either EDACS, Motorola, or LTR in a bank at one
time. You can, however, mix conventional channels
and frequencies in a bank.
If you are programming trunked frequencies for
Motorola Type I and hybrid systems, you must first
program the fleet map (see “Programming Fleet
Maps”).
If you are programming frequencies for an EDACS
system you must store them in the Logical Channel
Number order (usually listed as LCN#). For
example, LCN1 would go into channel 01 for the
current bank, and LCN2 would go into channel 02.
If you are programming frequencies for an LTR
system you must store them in the home repeater
71
Beyond the Basics
order. For example, home repeater order 1 would
go into channel 01 for the current bank, and home
repeater order 2 would go into channel 02.
Follow these steps to program trunked frequencies:
1. Press PROG and select the bank.
Note
To move through the bank selection faster, press
PROG then FUNC and hold down e or d. To move
through the banks one at a time, repeat the
sequence of PROG, FUNC then e or d until you reach
the desired bank.
2. Press TRUNK to enter the ID program mode.
3. Repeatedly press MODE to select Motorola, EDACS
(GE/Ericsson), or LTR (EF Johnson) system to scan.
This sets the talk group ID decoding method to be
used for the bank.
Note
If you select conventional mode instead of
Motorola, EDACS, or LTR, the scanner does not
scan trunked frequencies. Trunking mode not
selected, press Mode key. appears.
72
Beyond the Basics
4. Press PROG to enter the program mode.
5. Enter the desired trunking frequency then press ENT
to store.
6. To enter additional trunking frequencies as
subsequent channels in the same bank, press PROG
or e to access the next open channel then enter
the frequencies. (See “Storing Known Frequencies
into Channels”).
7. Press SCAN to start scanning.
If you enter a frequency that has already been
Note
entered in the current bank, the scanner sounds an
error tone and displays Dupl.Freq. and the channel
number that has been duplicated. If the dual
entry is an error press CLEAR and enter the correct
73
Beyond the Basics
frequency. If the dual entry is intentional press ENT
to accept.
You may replace any frequency by selecting the
bank and channel, pressing PROG and entering the
new frequency.
If you make an error in the entry process, press CLEAR
as often as needed to erase the incorrect data.
programming Motorola trunking systems
(UHF-Lo)
You can program the scanner to receive transmissions
in the UHF-Lo band (406-512 MHz) of the Motorola
trunking system. You can receive these transmissions
by checking the trunking system’s control channel. You
must program the system’s base frequency and offset
frequency to do this.
Note
Base and offset frequencies vary for each type of
trunking system. You can get information about
these frequencies for the trunking system you
want to scan using www.trunkscanner.com, other
Internet sources, or locally published guidebooks.
If you try to program an offset frequency in the UHF-Hi
bands (806-960 MHz), the scanner ignores the entry.
Follow these steps to program Motorola trunking
frequencies in the UHF-Lo band:
1. Press PROG then TRUNK to enter the ID program
mode.
2. Press FUNC and press (or hold) e or d to select the
bank.
3. Press MODE and select MOT.
74
Beyond the Basics
4. Press FUNC then 2. The display indicates Custom Range
1/3 on first line, Base: 406.0000 on the second line,
Offset: 380 on the third line and Step:25.0kHz on the
bottom line.
5. While B in Base blinks, if necessary, press the
desired Base frequency with the number keys and
press ENT. Confirm the entry. If it is incorrect, press
the number keys again to set the base frequency.
After you confirm the input, press ENT again.
6. While O in Offset blinks, if necessary, enter the offset
number and press ENT. Confirm the entry. If it is
incorrect, then press the number keys again to set
the frequency. After you confirm the input, press
ENT again.
7. While S in Step blinks, repeatedly press e or d to
select the step number, 5.0, 6.25, 10.0, 12.5, 15.0,
18.75, 20.0, 25.0, 30.0, 31.25, 35.0, 37.5, 40.0,
43.75, or 50.0 kHz, then press ENT.
8. Press PROG to enter the program mode. Store the
trunking IDs into the sub-bank in the same bank.
programming Motorola trunking systems (800
MHz)
Follow these steps to program 800 MHz band Motorola
trunking.
Note
On the 800 MHz trunking band, you can select a
base frequency (normal or offset).
On the 900 MHz trunking band, you do not need to
set the base frequency (base, offset, step).
1. Press PROG then TRUNK to enter the ID program
mode.
75
Beyond the Basics
2. Press FUNC then e or d to select the desired bank.
3. Press MODE and select Motorola trunking mode.
4. Press FUNC then 3. Use Up/Down keys to set 800MHz
Motorola ch plan NORMAL appears.
5. Press e or d to select NORMAL or SPLINTER and
press ENT.
•
If you are uncertain about the base frequency, use
the default setting. The default setting is normal.
•
If you cannot receive with the normal setting,
change to OFFset. The base frequency in normal
is 851.0125 MHz. The base frequency in OFFset is
851.0000 MHz.
programming fleet maps
You must set the fleet map if you want to receive a
Motorola Type I system. Fleet maps are included along
with other information about Motorola Type I systems
at www.trunkscanner.com.
Follow these steps to program a fleet map.
1. Press PROG then TRUNK.
2. For each bank you want to program, repeatedly
press FUNC. Then e or d to select the bank.
3. Press FUNC. Then press 8. Size Code Setting appears.
76
Beyond the Basics
4. Enter the size code supplied with the Type I system
information, referring to the instruction that
appears on the display. If the information was not
supplied, try the following common fleet maps.
Block
Size Code
1
2
3
4
5
6
7
8
0
S11
S4
S4
S12
S4
S3
S10
S1
1
S11
S4
S4
—
S4
S10
S10
S1
2
S11
S4
S4
S4
S12
S4
S11
S2
3
S11
S4
S4
S4
—
S4
S4
S2
4
S11
S4
S4
S4
S4
S12
S4
S3
5
S11
S4
S4
S4
S4
—
S4
S3
6
S11
S4
S12
S4
S4
S12
S4
S4
7
S11
S4
—
S4
S4
—
S4
S4
Block
Size Code
9
10
11
12
13
14
15
16
0
S4
S0
S4
S0
S3
S4
S4
S3
1
S4
S0
S0
S0
S3
S3
S4
S10
2
S0
S0
S0
S0
S11
S10
S4
S10
3
S0
S0
S0
S0
S4
S4
S11
S11
4
S0
S0
S0
S0
S4
S4
S11
S0
5
S0
S0
S0
S0
S0
S4
S0
S0
6
S0
S4
S0
S0
S0
S12
S12
S12
7
S0
S4
S0
S4
S0
—
—
—
77
Beyond the Basics
5. Press ENT for each entry. If you make a mistake,
press CLEAR and enter the correct size code.
The default setting of the bank is for Motorola Type
Note
II. However, if you set Type I and you want to return
to Type II, enter 15 at Step 4.
To confirm the input, repeat Steps 1-5 and press
ENT. Each time you press ENT, you confirm the size
code. If you find an error, press CLEAR and begin
again at Step 1.
6. Press SCAN to start scanning.
talk group IDs
There are 10 talk group ID banks and each ID bank has
5 sub-banks. Each sub-bank has 30 ID locations. You
can program up to 150 talk group IDs in each bank,
so you can program up to 1,500 talk group IDs in 10
banks. When the scanner stops on a transmission in
the Motorola, EDACS, or LTR mode, it checks to see
if the ID has been stored. In the closed mode, the
scanner only stops on the transmission and displays
its text tag if you have stored and not locked out the
ID. In the open mode, the scanner always stops on a
transmission, but it displays the ID’s text tag if you have
stored the ID.
storing talk group IDs
To store a talk group ID, press TRUNK when the scanner
stops on a voice channel transmission or when a talk
group ID is indicated in the manual mode. The bottom
line indicates where the ID was stored (as ID save XXX), then it changes to ID#XXXX.
78
Beyond the Basics
The first X in ID save X-XX is the sub-bank number (0-4)
in the bank. XX is the number of IDs from (00-29) in
each sub-bank.
If the ID has already been stored when you press
TRUNK, ID was saved appears.
Note
When you try to store more than 150 talk group
IDs in a bank, Memory Full! appears. Clear some
talk group IDs in order to store new ones (see
“Clearing Talk Group IDs”).
Follow these steps to manually store talk group IDs or
to edit a stored ID.
1. Press PROG.
2. Press TRUNK.
3. To select the bank where you want to store the ID,
repeatedly press FUNC then e or d until you reach
the desired bank.
4. Press MODE to select MOT, ED, or LTR.
5. Repeatedly press TRUNK to select the sub-bank.
6. Press e or d to select the location where you
desire to store the ID number.
7. Enter the talk group ID and press ENT. If necessary,
use the decimal point for a hyphen.
79
Beyond the Basics
8. If you want to tag the ID, press TEXT, enter the
desired text tag for the ID. Then press ENT (see
“Text Input Chart”).
9. To store the next ID memory in sequence, press e
and repeat Step 7.
10. Press SCAN to start scanning.
If you made a mistake in Step 4, Invalid ID value
Note
appears and the scanner beeps when you press
ENT. Start again at Step 3.
You can enter either a decimal or AFS code for
ED (EDACS) IDs. The default setting is decimal ID
entry. When you press FUNC then 2, AFS Format
appears for about 2 seconds. Now you can enter
the ID code with AFS format.
If you entered an ID code that is already stored in
another ID channel, Dupl. ID of X-XX appears. If you
want to store the ID code, press ENT. To cancel the
operation, press CLEAR.
80
Beyond the Basics
talk group ID hold
You can set your scanner to follow a trunking signal
that you want to track during scanning. While the
scanner is stopped on a voice channel (VC appears),
hold down TRUNK until ID hold ON. appears.
When ID hold is activated and the scanner receives a
voice channel, the scan indication S at the first digit in
the top line changes to H.
To release ID hold, press SCAN or TRUNK.
turning an ID sub-bank on or off
Follow these steps to turn the ID sub-bank on or off
during the program mode:
1. Press TRUNK repeatedly to select the desired subbank.
2. Press FUNC then 1 to turn the sub-bank on if it is off
or off if it is on.
Follow these steps to turn the ID sub-bank on or off
during the scan mode:
1. Press FUNC while the scanner is stopped on a voice
channel transmission.
2. Press TRUNK. The display indicates which sub-bank
is turned on or off, and the active sub-bank number
flashes.
81
Beyond the Basics
3. Press FUNC and the number of the sub-bank you
desire to turn on or off. For example to turn subbank 4 on or off, press FUNC. Then press 4.
locking out talk group IDs
1. Press PROG.
You can only lock out talk group IDs when the
Note
scanner is in the closed mode (see “Open and
Closed Modes”).
2. Press TRUNK.
3. Press FUNC, e or d to move to the desired bank.
4. Press e or d to select the ID memory.
5. Press L/OUT to lock out the ID. lo changes to LO.
6. To remove the lockout from a trunking ID, manually
select the ID memory, and press L/OUT. LO changes
to lo.
You can confirm the ID code while the scanner shows
the text when the received signal is a voice channel.
1. Press TEXT while the scanner is receiving the voice
channel and indicating the text name. The ID code
appears as MOT:XXXXXX, etc.
2. Press TEXT again to cancel.
delay function in ID indication mode
You can set the ID delay function separate from the
channel delay.
82
Beyond the Basics
1. Press FUNC then ./DELAY while you are programming
the trunked ID. Use Up/Down keys to set ID Delay. ENTER
key saves. 2.0 seconds appears.
2. Press e or d to select None, 0.5, 1.0, 1.5, 2.0, 2.5,
3.0, 3.5, or 4.0 seconds.
3. Press ENT.
When activated, ID delay watches the control
Note
channel command for the delay time when the
signal disappears from the voice channel.
reviewing locked-out talk group IDs
You cannot clear all lockouts from a talk group at the
same time.
1. Press PROG then TRUNK.
2. Press FUNC. Then L/OUT. The locked out ID appears.
If the ID memory bank has no locked-out ID, you
hear the low beep tone.
clearing talk group IDs
1. Press PROG then TRUNK.
2. Press FUNC, e or d to select ID memory.
3. Press FUNC then CLEAR.
clearing all talk group IDs in a single bank
You can clear all talk group IDs within a bank. This lets
you quickly delete all talk group IDs from a bank if you
want to use the bank to store different data (such as a
new set of talk group IDs).
83
Beyond the Basics
1. Press PROG.
2. Press TRUNK to enter a talk group ID memory mode.
3. Select a talk group ID bank using FUNC, e or d.
4. Press FUNC then 6. Clear entire list ? Press 1 to clear all, any
other key aborts appears.
5. Press 1 to clear all talk group IDs within a bank. List
cleared. appears.
To cancel the deletion, press any key except 1. The
scanner returns to the talk group ID memory mode.
changing the open/closed mode
1. Press MAN.
2. Press FUNC then e or d to select the channel
storage bank.
3. Press FUNC then ./DELAY. Bank OPEN. or Bank
CLOSED. appears. After that message disappears,
the fifteenth digit on the second line of the display
changes from + to – or vice versa.
4. Repeat Steps 2 and 3 for each bank.
84
Beyond the Basics
care
Keep the scanner dry; if it gets wet, wipe it dry
immediately. Use and store the scanner only in normal
temperature environments. Handle the scanner
carefully; do not drop it. Keep the scanner away
from dust and dirt, and wipe it with a damp cloth
occasionally to keep it looking new.
replacing fuse
Frist, turn off the scanner and your vehicle’s ignition.
Make sure you replace the fuse only with another fuse
of the same type and rating (2-amp, fast-acting glass
fuse).
resetting/initializing your scanner
If the scanner’s display locks up or does not work
properly after you connect a power source, you might
need to reset or initialize it. If you have problems with
the scanner, first try resetting it, which will retain items
stored in memory. If that does not work, initialize the
scanner. You may be able to save the information in
your scanner’s memory to your computer, or another
scanner before initializing it. See “Cloning Programmed
Data”.
Warning! Unspecified key operations may clear your
scanner’s memory.
resetting your scanner
1. Turn off your scanner, and then turn it on again.
2. Insert a pointed object into the reset hole on the
back of the scanner. Then, gently press and release
the reset button.
85
Beyond the Basics
initializing your scanner
Initializing your scanner clears all information stored
in your scanner’s working memory. Initialize your
scanner only when you are sure it is not working
properly.
1. Turn off the scanner, and turn it on again. Multisystem Trunking Scanner appears.
2. Press 0 while Multi-system Trunking Scanner appears.
3. Press 1.
Note
4. Press ENT. Initializing please stand by. appears for about
5 seconds.
Do not turn off your scanner until the initialization
is complete. When the initialization is complete,
M000 and Bank 0 Ch 00 appear on the display.
service and repair
If your scanner is not performing as it should, take
it to your local RadioShack store for assistance. To
locate your nearest RadioShack, use the store locator
feature on RadioShack’s website (www.radioshack.
com), or call 1-800-The Shack (800-843-7422) and
follow the menu options. Modifying or tampering
with the scanner’s internal components can cause a
malfunction and might invalidate its warranty and void
your FCC authorization to operate it.
birdie frequencies
Every scanner has birdie frequencies. Birdies
are signals created inside the scanner’s receiver.
These operating frequencies might interfere with
86
Beyond the Basics
transmissions on the same frequencies. If you
program one of these frequencies, you hear only noise
on that frequency. If the interference is not severe, you
might be able to turn SQ clockwise to omit the birdie.
To find the birdies in your scanner, begin by
disconnecting the antenna and moving it away from
the scanner. Make sure that no other nearby radio
or TV sets are turned on near the scanner. Use the
search function and scan every frequency range from
its lowest frequency to the highest. Occasionally, the
searching will stop as if it had found a signal, often
without any sound. This is a birdie. Make a list of all
the birdies in your scanner for future reference.
87
Beyond the Basics
specifications
Frequency Coverage:
25–54 MHz ...................................................... (in 5 kHz steps)
108–136.99166 MHz .................................. (in 8.33 kHz steps)
137–174 MHz ..................... (in 5, 6.25, 7.5, or 12.5 kHz steps)
216.0025–225.0000 MHz ................................ (in 5 kHz steps)
225.025–405.975 MHz .................................. (in 25 kHz steps)
406–512 MHz ...............................................(in 6.25 kHz steps)
806–823.9875 MHz .................................... (in 6.25 kHz steps)
849–868.9875 MHz .................................... (in 6.25 kHz steps)
894– 960 MHz ............................................. (in 6.25 kHz steps)
1240–1300 MHz ......................................... (in 6.25 kHz steps)
Memory channels .............................................................1000
Channel memory banks .......................................................10
Number of memory channels per bank ............................100
Talk group ID memories ..................................................1,500
ID memory banks .................................................................10
Sub-banks per bank .............................................................. 5
Number of memory IDs per sub-bank ............................... 30
Sensitivity (20 dB S/N):
FM:
25–54 MHz ..................................................................... 0.3 µV
108 –136.99166 MHz ..................................................... 0.3 µV
137–174 MHz ................................................................. 0.5 µV
216–225 MHz .................................................................... 1 µV
406–512 MHz ................................................................ 0.5 µV
88
Beyond the Basics
806–960 MHz ................................................................. 0.7 µV
1240–1300 MHz ............................................................. 0.7 µV
AM:
25–54 MHz ........................................................................ 1 µV
108–136.99166 MHz ......................................................... 1 µV
137–174 MHz ................................................................. 1.5 µV
216–225 MHz .................................................................... 3 µV
406–512 MHz .................................................................... 2 µV
806–960 MHz .................................................................... 2 µV
1240–1300 MHz ................................................................ 3 µV
Selectivity:
25 – 27.995 MHz at AM mode
–6 dB ..............................................................................±5 kHz
–50 dB ........................................................................... ±6 kHz
All frequencies at AM and FM mode except 25 – 27.995 MHz
at AM
–6 dB ........................................................................... ±10 kHz
–50 dB ..........................................................................±18 kHz
Spurious Rejection (at 154.1 MHz FM) ........................... 40 dB
Scanning Rate ........................ Up to 60 Channels per Second
Search Rate ..................................Up to 75 Steps per Second
Delay Time ...............................................................2 seconds
Intermediate Frequencies (IF):
1st ............................................................................ 380.8 MHz
2nd ............................................................................. 21.4 MHz
3rd ............................................................................... 455 kHz
Priority Sampling .................................................... 2 seconds
89
Beyond the Basics
Operating Temperature .................. –14 to 140° F (–20 to 60°)
IF Rejection:
380.8 MHz at 154.1 MHz ................................................. 60 dB
21.4 MHz at 154.1 MHz ................................................. 100 dB
Squelch Sensitivity:
Threshold (FM and AM) ................................................. 0.5 µV
Tight (FM) ........................................................................ 25 dB
Tight (AM) ........................................................................ 20 dB
Antenna Impedance ...................................................50 Ohms
Audio Output Power (10% THD) .................................... 1.5 W
Built-in Speaker ............................................ 3 Inches (77 mm)
(8-ohm, Dynamic Type)
Power Requirements ...................................................... 13.8 V
Current Drain ...............................................................600 mA
Dimensions (HWD) ......................2 1/4 x 7 1/4 x 5 5/16 Inches
(55 x 185 x 135 mm)
Weight (without cabinet and accessories) ..... 27.7 oz. (790 g)
Specifications are typical; individual units might vary.
Specifications and depictions are subject to change and
improvement without notice.
90
Beyond the Basics
The FCC wants you to know
This equipment has been tested and found to comply with the limits
for a scanning receiver, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
scanning legally
Your scanner covers frequencies used by many different groups
including police and fire departments, ambulance services,
government agencies, private companies, amateur radio services,
military operations, pager services, and wireline (telephone and
telegraph) service providers. It is legal to listen to almost every
transmission your scanner can receive. However, there are some
transmissions you should never intentionally listen to. These
include:
• Telephone conversations (cellular, cordless, or other private
means of telephone signal transmission)
• Pager transmissions
• Any scrambled or encrypted transmissions
According to the Electronic Communications Privacy Act (ECPA),
you are subject to fines and possible imprisonment for intentionally
listening to, using, or divulging the contents of such a transmission
91
Beyond the Basics
unless you have the consent of a party to the communication (unless
such activity is otherwise illegal).
This scanner has been designed to prevent reception of illegal
transmissions. This is done to comply with the legal requirement
that scanners be manufactured so as to not be easily modifiable to
pick up those transmissions. Do not open your scanner’s case to
make any modifications that could allow it to pick up transmissions
that are illegal to monitor. Doing so could subject you to legal
penalties.
In some areas, mobile use of this scanner is unlawful or requires a
permit. Check the laws in your area. It is also illegal in many areas to
interfere with the duties of public safety officials by traveling to the
scene of an incident without authorization.
We encourage responsible, safe and legal scanner use.
92
Beyond the Basics
glossary
Frequency — the receving signal location (expressed
in MHz). To find active frequencies, you can
use frequency guides available from your local
RadioShack store, frequency listings posted on the
Internet, or the built-in search function.
Channels — programmable memory locations for
the frequencies you want to monitor. Each time
the scanner finds an active frequency, it stops and
monitors the radio traffic on that channel until the
transmission ends, then resumes scanning.
Channel Storage Banks — a storage area for a
group of channels. Channels are storage areas for
frequencies. Whereas a channel can only contain one
frequency, a bank can hold numerous channels.
Search Banks – contain preprogrammed frequencies
in the scanner’s memory. Your scanner has six
preprogrammed search banks configured to search
various radio services, and one limit search bank that
you can configure. You can set the lower and higher
frequency limit in the limit search bank. For example,
if you wanted to find active frequencies between a
range of 150.1000 and 150.5000, you would put both
of those frequencies in the limit search bank. You can
even change the frequency range in a search bank
(SR6) to customize your search parameters.
Talkgroup IDs — each channel storage bank has an
associated talkgroup ID list, for a total of 10 talkgroup
ID lists. Each ID list has 5 sub-banks. Each sub-bank
has 30 ID locations. You can program up to 150
talkgroup IDs in each bank, so you can program up
to 1500 talkgroup IDs in 10 banks. When the scanner
93
Beyond the Basics
stops on a transmission in the Motorola or EDACS
mode, it checks to see if the ID has been stored in the
associated ID list. In the Closed Mode, the scanner
only stops on the transmission and displays its text
tag if you have stored and not locked out the ID. In
the Open Mode, the scanner always stops on all
transmissions except those you specifically exclude,
and diplays the ID’s text tag if you have stored the ID.
For a detailed description of Open and Closed Mode
operation, see “Open and Closed Mode Operation”.
94
Beyond the Basics
FAQs (Frequently Asked
Questions)
The scanner is not working at all. What’s wrong?
The AC or DC adapter or DC cable might not be
connected. Be sure the adapter/cable’s barrel plug is
fully inserted into the PWR DC 13.8V jack. The center
tip of the adapter/cable’s barrel plug must be set to
positive.
The scanner does not receive any stations or
reception is poor. What’s wrong?
The scanner might need to be reset or initialized. Insert
a pointed object into the reset hole on the back of the
scanner, or initialize the scanner (see”Initializing your
Scanner”).
The scanner is on but does not scan. What’s wrong?
The squelch might not be adjusted correctly. Turn SQ
clockwise. There might only be one channel or no
channels stored in the scanner. Store frequencies into
more than one channel.
While scanning, the scanner locks on frequencies that
have an unclear transmission. What’s wrong?
Some frequencies programmed into the scanner
might be the same as “birdie” frequencies. Avoid
programming “Birdie Frequencies” or only listen to
them manually.
95
This product is warranted by RadioShack against manufacturing defects in material
and workmanship under normal use for one (1) year from the date of purchase
from RadioShack company-owned stores and authorized RadioShack franchisees
and dealers. For complete warranty details and exclusions, check with your local
RadioShack store.
RadioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102
04/04
Printed in Hong Kong
GE-05D-0620
04A05
©2005. RadioShack Corporation.
All rights reserved. RadioShack and RadioShack.com are
trademarks used by RadioShack Corporation.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement