Emerson EWC1303 Service manual

SERVICE MANUAL
Main Section
I Specifications
I Preparation for Servicing
I Adjustment Procedures
I Schematic Diagrams
I CBA’s
I Exploded Views
I Parts List
When servicing the deck
mechanism, refer to MK12.5 Deck
Mechanism Section.
Deck Mechanism Part No.:
N2226FT
13" COLOR TV/VCR COMBINATION
EWC1303A
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and
described in this service manual are effective methods of performing service
operations. Some of these service special tools should be used when and as
recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk of
personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand
that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not
possibly know, evaluate and advice the service trade of all conceivable ways
in which service might be done or of the possible hazardous consequences of
each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by
the service method selected.
MAIN SECTION
13" COLOR TV/VCR COMBINATION
EWC1303A
Main Section
I Specifications
I Preparation for Servicing
I Adjustment Procedures
I Schematic Diagrams
I CBA’s
I Exploded Views
I Parts List
TABLE OF CONTENTS
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1
Important Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1
Preparation for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1
Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5-1
Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1
Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1
Mechanical Trouble Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-7
Power Supply Trouble Shooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-9
Schematic Diagrams / CBA’s and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8-1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10-1
System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1
IC Pin Function Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1
Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1
Cabinet Exploded Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1
Packing Exploded Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-3
Mechanical Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1
Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1
SPECIFICATIONS
*ˆMode---------SP mode unless otherwise specified
*Test input terminal
<Except Tuner>-------------Video input (1Vp-p)
Audio input (-10dB)
<Tuner>-----------------------Ant. input (80dBµV) Video: 87.5%
Audio: 25kHz dev (1kHz Sin)
<DEFLECTION>
Description
Condition
Unit
Nominal
Limit
—
%
90
±5
Horizontal
%
—
15
Vertical
%
—
10
—
kV
22
—
Condition
Unit
Nominal
Limit
Center
m/m
—
0.3
Corner
m/m
—
1.5
Side
m/m
—
1.2
2. Tint Control Range
—
deg
±30
—
3. Contrast Control Range
—
dB
12
8
APL 100%
ft-L
55
40
—
K
9200
—
Condition
Unit
Nominal
Limit
1. Horizontal Resolution
(R/P)
Line
230
200
2. Jitter (Low)
(R/P)
µS
0.05
0.2
(R/P)
dB
38
33
(R/P)
dB
36
33
(R/P)
%
0.25
0.5
Condition
Unit
Nominal
Limit
1. Video S/N
—
dB
45
40
2. Audio S/N (W/LPF)
—
dB
43
40
1. Over Scan
2. Linearity
3. High Voltage
<VIDEO & CHROMA>
Description
1. Misconvergence
4. Brightness
5. Color Temperature
<VCR>
Description
3. S/N Chroma
AM(SP)
PM(SP)
4. Wow & Flutter (RMS)
<TUNER>
Description
1-1-1
T5553SP
<AUDIO>
All items are measured across 8Ω resistor at speaker output terminal.
Description
Condition
Unit
Nominal
Limit
1. Audio Output Power (Max.)
(R/P)
W
1.0
0.8
2. Audio S/N (W/LPF)
(R/P)
dB
40
36
3. Audio Distortion (W/LPF)
(R/P)
%
3.0
5.0
200Hz (R/P)
8kHz (R/P)
dB
dB
-2.0
0
-2.0±5.0
0±6.0
4. Audio Freq. Response
(-10dB Ref. 1KHz)
Note: Nominal specifications represent the design specifications. All units should be able to approximate these.
Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications.
1-1-2
T5553SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for TV Circuit
1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following
items:
a. Be sure that no built-in protective devices are defective and have been defeated during servicing.
(1) Protective shields are provided on this chassis
to protect both the technician and the customer.
Correctly replace all missing protective shields, including any removed for servicing convenience. (2)
When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all
protective devices, including but not limited to,
nonmetallic control knobs, insulating fishpapers,
adjustment and compartment covers/shields, and
isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated
without all protective devices correctly installed and functioning. Servicers who defeat
safety features or fail to perform safety checks
may be liable for any resulting damage.
b. Be sure that there are no cabinet openings through
which an adult or child might be able to insert their
fingers and contact a hazardous voltage. Such
openings include, but are not limited to, (1) spacing
between the picture tube and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and (3)
an improperly fitted and/or incorrectly secured
cabinet back cover.
c. Antenna Cold Check - With the instrument AC
plug removed from any AC source, connect an
electrical jumper across the two AC plug prongs.
Place the instrument AC switch in the on position.
Connect one lead of an ohmmeter to the AC plug
prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the
coaxial connector. If the measured resistance is
less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected
before the instrument is returned to the customer.
Repeat this test with the instrument AC switch in
the off position.
d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line
cord directly into a 120V AC outlet. (Do not use an
isolation transformer during this test.) Use a leak-
1-2-1
age current tester or a metering system that complies with American National Standards Institute
(ANSI) C101.1 Leakage Current for Appliances
and Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on position and then in the off position, measure from a
known earth ground (metal water pipe, conduit,
etc.) to all exposed metal parts of the instrument
(antennas, handle brackets, metal cabinet, screw
heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current
measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet
and repeat the test.
READING SHOULD
NOT BE ABOVE 0.5 mA
DEVICE
BEING
TESTED
LEAKAGE
CURRENT
TESTER
TEST ALL EXPOSED
METAL SURFACES
ALSO TEST WITH
PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
EARTH
GROUND
ANY MEASUREMENTS NOT WITHIN THE LIMITS
SPECIFIED HEREIN INDICATE A POTENTIAL
SHOCK HAZARD THAT MUST BE ELIMINATED
BEFORE RETURNING THE INSTRUMENT TO
THE CUSTOMER OR BEFORE CONNECTING
THE ANTENNA OR ACCESSORIES.
e. X-Radiation and High Voltage Limits - Because
the picture tube is the primary potential source of
X-radiation in solid-state TV receivers, it is specially constructed to prohibit X-radiation emissions.
For continued X-radiation protection, the replacement picture tube must be the same type as the
original. Also, because the picture tube shields
and mounting hardware perform an X-radiation
protection function, they must be correctly in place.
High voltage must be measured each time servic-
SFTY_2
ing is performed that involves B+, horizontal deflection or high voltage. Correct operation of the
X-radiation protection circuits also must be reconfirmed each time they are serviced. (X-radiation
protection circuits also may be called "horizontal
disable" or "hold down.") Read and apply the high
voltage limits and, if the chassis is so equipped,
the X-radiation protection circuit specifications given on instrument labels and in the Product Safety
& X-Radiation Warning note on the service data
chassis schematic. High voltage is maintained
within specified limits by close tolerance safety-related components/adjustments in the high-voltage
circuit. If high voltage exceeds specified limits,
check each component specified on the chassis
schematic and take corrective action.
2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the
receiver chassis, or on the picture tube.
3. Design Alteration Warning - Do not alter or add
to the mechanical or electrical design of this TV receiver. Design alterations and additions, including,
but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video
output connections, might alter the safety characteristics of this receiver and create a hazard to the
user. Any design alterations or additions will void
the manufacturer's warranty and may make you,
the servicer, responsible for personal injury or
property damage resulting therefrom.
4. Picture Tube Implosion Protection Warning The picture tube in this receiver employs integral
implosion protection. For continued implosion protection, replace the picture tube only with one of
the same type number. Do not remove, install, or
otherwise handle the picture tube in any manner
without first putting on shatterproof goggles
equipped with side shields. People not so
equipped must be kept safely away while picture
tubes are handled. Keep the picture tube away
from your body. Do not handle the picture tube by
its neck. Some "in-line" picture tubes are equipped
with a permanently attached deflection yoke; because of potential hazard, do not try to remove
such "permanently attached" yokes from the picture tube.
5. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord
and maybe safety-serviced without an isolation
transformer only if the AC power plug is inserted
so that the chassis is connected to the ground side
of the AC power source. To confirm that the AC
power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known
1-2-2
earth ground. If a voltage reading in excess of 1.0V
is obtained, remove and reinsert the AC power
plug in the opposite polarity and again measure
the voltage potential between the chassis and a
known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can
be safety-serviced only with an isolation transformer inserted in the power line between the receiver
and the AC power source, for both personnel and
test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation
material that must not be defeated or altered.
6. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage,
and e. antenna wiring. Always inspect in all areas
for pinched, out of place, or frayed wiring. Check
AC power cord for damage.
7. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or wiring that meet original specifications. Additionally,
determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.
8. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual
inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc.. Parts
that have special safety characteristics are identified by a ( # ) on schematics and in parts lists. Use
of a substitute replacement that does not have the
same safety characteristics as the recommended
replacement part might create shock, fire, and/or
other hazards. The Product's Safety is under review continuously and new instructions are issued
whenever appropriate. Prior to shipment from the
factory, our products are strictly inspected to confirm with the recognized product safety and electrical codes of the countries in which they are to be
sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
SFTY_2
Precautions during Servicing
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
A. Parts identified by the ( # ) symbol are critical for
safety.
I. Also check areas surrounding repaired locations.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set.
K. Crimp type wire connector
When replacing the power transformer in sets
where the connections between the power cord
and power transformer primary lead wires are performed using crimp type connectors, in order to
prevent shock hazards, perform carefully and precisely the following steps.
Replacement procedure
2) Double insulated wires
1) Remove the old connector by cutting the wires at
a point close to the connector.
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
Important: Do not re-use a connector (discard it).
2) Strip about 15 mm of the insulation from the ends
of the wires. If the wires are stranded, twist the
strands to avoid frayed conductors.
3) Align the lengths of the wires to be connected. Insert the wires fully into the connector.
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heatsinks, oxide metal film resistors, fusible resistors, etc.)
4) Use the crimping tool to crimp the metal sleeve at
the center position. Be sure to crimp fully to the
complete closure of the tool.
L. When connecting or disconnecting the VCR connectors, first, disconnect the AC plug from AC supply socket.
G. Check that replaced wires do not contact sharp
edged or pointed parts.
1-2-3
SFTY_2
Safety Check after Servicing
Examine the area surrounding the repaired location
for damage or deterioration. Observe that screws,
parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance
with safety standards.
Chassis or Secondary Conductor
Primary Circuit Terminals
d'
d
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1 : Ratings for selected area
AC Line Voltage
Region
Clearance
Distance (d) (d')
110 to 130 V
USA or
CANADA
≥ 3.2 mm
(0.126 inches)
Fig. 1
Note: This table is unofficial and for reference only.
Be sure to confirm the precise values.
Exposed Accessible Part
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.).
AC Voltmeter
(High Impedance)
Z
Measuring Method : (Power ON)
Insert load Z between B (earth ground, power cord
plug prongs) and exposed accessible parts. Use an
AC voltmeter to measure across both terminals of load
Z. See Fig. 2 and following table.
B
One side of
Power Cord Plug Prongs
Fig. 2
Table 2 : Leakage current ratings for selected areas
AC Line Voltage
Region
Load Z
Leakage Current (i)
Earth Ground (B) to:
110 to 130 V
USA or
CANADA
0.15µF CAP. & 1.5kΩ
RES. connected in
parallel
i≤0.5mA rms
Exposed accessible
parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
1-2-4
SFTY_2
STANDARD NOTES FOR SERVICING
Circuit Board Indications
How to Read the Values of the Rectangular Type Chip Components
1. The output pin of the 3 pin Regulator ICs is indicated as shown:
Top View
Out
Example:
(a) Resistor
Bottom View
In
473
Input
= 473 = 47 [kΩ]
2. For other ICs, pin 1 and every 5th pin is indicated
as shown:
(Top View)
(b) Capacitor
5
Pin 1
= Not Shown
(Top View)
Caution:
Once chip parts (Resistors, Capacitors, Transistors,
etc.) are removed, they must not be reused. Always
use a new part.
10
3. The 1st pin of every pin connector are indicated as
shown:
Pb Free Solder (PbF)
Pin 1
When soldering, be sure to use the Pb free solder.
Replacement Procedures for
Leadless (Chip) Components
Instructions for Connectors
1. When you connect or disconnect FFC cable (connector), be sure to disconnect the AC cord.
The Following Procedures are Recommended for the Replacement of the Leadless Components Used in this Unit.
2. FFC cable (connector) should be inserted parallel
into the connector, not at an angle.
1. Preparation for replacement
a. Soldering Iron
Use a pencil-type soldering iron (less than 30
watts).
FFC Cable
b. Solder
Eutectic solder (Tin 63%, Lead 37%) is recommended.
Connector
c. Soldering time
Do not apply heat for more than 4 seconds.
CBA
d. Preheating
Leadless capacitor must be preheated before
installation. (130°C~150°C, for about two minutes.)
* Be careful to avoid a short circuit.
Notes:
a. Leadless components must not be reused after
removal.
[ CBA= Circuit Board Assembly ]
b. Excessive mechanical stress and rubbing for the
component electrode must be avoided.
1-3-1
SFTY_Z13N
How to Remove / Install Flat Pack IC
2. Removing the leadless component
Grasp the leadless component body with tweezers
and alternately apply heat to both electrodes. When
the solder on both electrodes has melted, remove
leadless component with a twisting motion.
Caution:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
Notes:
2. Do not apply the hot air to the chip parts around the
Flat Pack-IC for over 6 seconds as damage may
occur to the chip parts. Put Masking Tape around
the Flat Pack-IC to protect other parts from damage. (Fig. S-1-2)
a. Do not attempt to lift the component off the board
until the component is completely disconnected
from the board by the twisting action.
b. Take care not to break the copper foil on the printed
board
3. The Flat Pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or solder lands under the IC when removing it.
3. Installing the leadless component
a. Presolder the contact points of the circuit board.
b. Press the part downward with tweezers and solder
both electrodes as shown below.
1. Removal
With Hot - Air Flat Pack - IC Desoldering Machine:
a. Prepare the Hot - Air Flat Pack - IC Desoldering
Machine, then apply hot air to Flat Pack - IC (about
5~6 seconds). (Fig. S-1-1)
Note:
Do not glue the replacement leadless component to
the circuit board.
b. Remove the Flat Pack- IC with tweezers while
applying the hot air.
Tweezers
With Soldering Iron:
a. Using desoldering braid, remove the solder from all
pins of the Flat Pack - IC. When you use solder flux
which is applied to all pins of the Flat Pack - IC, you
can remove it easily. (Fig. S-1-3)
Chip
b. Lift each lead of the Flat Pack - IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air Desoldering
Machine. (Fig. S-1-4)
Soldering Iron
With Iron Wire:
Tweezers
a. Using desoldering braid, remove the solder from all
pins of the Flat Pack - IC. When you use solder flux
which is applied to all pins of the Flat Pack - IC, you
can remove it easily. (Fig. S-1-3)
Soldering Iron
Solder
b. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
c. Pull up on the wire as the solder melts so as to lift
the IC leads from the CBA contact pads, while
heating the pins using a fine tip soldering iron or
hot air blower.
Soldering Iron
Note:
Presolder
When using a soldering iron, care must be taken
to ensure that the Flat Pack - IC is not being held
by glue, or when it is removed from the CBA, it
may be damaged if force is used.
1-3-2
SFTY_Z13N
2. Installation
a. Using desoldering braid, remove the solder from
the foil of each pin of the Flat Pack - IC on the CBA,
so you can install a replacement Flat Pack - IC
more easily.
b. The "I" mark on the Flat Pack - IC indicates pin 1
(See Fig. S-1-6). Make sure this mark matches the
1 on the CBA when positioning for installation.
Then pre - solder the four corners of the Flat PackIC (See Fig. S-1-7).
Sharp
Pin
Fine Tip
Soldering Iron
c. Solder all pins of the Flat Pack - IC. Make sure that
none of the pins have solder bridges.
Fig. S-1-4
Hot Air Blower
or
Iron Wire
Soldering Iron
Fig. S-1-1
To Solid
Mounting Point
Fig. S-1-5
CBA
Masking
Tape
Tweezers
Hot-air
Flat Pack-IC
Desoldering
Machine
Example :
Flat Pack-IC
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Fig. S-1-2
Flat Pack-IC
Fig. S-1-6
Desoldering Braid
Soldering Iron
Fig. S-1-3
1-3-3
SFTY_Z13N
Instructions for Handling
Semiconductors
Presolder
Electrostatic breakdown of the semiconductors may
occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
Ground for Human Body
Be sure to wear a grounding band (1MΩ) that is properly grounded to remove any static electricity that may
be charged on the body.
Ground for Work Bench
Flat Pack-IC
Be sure to place a conductive sheet or copper plate
with proper grounding (1MΩ) on the work bench or
other surface, where the semiconductors are to be
placed. Because the static electricity charge on the
clothing will not escape through the body grounding
band, be careful to avoid contacting semiconductors to
clothing.
CBA
Fig. S-1-7
<Incorrect>
CBA
<Correct>
Grounding Band
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
1-3-4
SFTY_Z13N
PREPARATION FOR SERVICING
How to Enter the Service Mode
Key
Adjustment Mode
7
Purity check mode: Shows Red, Green,
Blue or White cyclically on the screen
each time the "7" key is pressed.
8
H. Shift adjustment mode: See
adjustment instructions page 1-6-4.
9
V.size/V. shift adjustment: See
adjustment instructions page 1-6-4.
1. Cover Q202 (START SENSOR) and Q201 (END
SENSOR) with Insulation Tape or enter the service
mode to activate Sensor Inhibition automatically.
VOL p
Initial Setting mode: See adjustment
instructions page 1-6-1.
Cut-off Adjustment mode: See
adjustment instructions page 1-6-4.
Note: Avoid playing, rewinding or fast forwarding the
tape to its beginning or end, because both Tape End
Sensors are not active.
Caution: 2
Caution: 1
1. Optical sensors system are used for Tape Start and
End Sensor on this equipment. Read this page
carefully and prepare as described on this page
before starting to service; otherwise, the unit may
operate unexpectedly.
Preparing: 1
1. The deck mechanism assembly is mounted on the
Main CBA directly, and SW211 (REC-SAFETY
SW) is mounted on the Main CBA. When deck
mechanism assembly is removed from the Main
CBA due to servicing, this switch can not be operated automatically.
How to Enter the Service Mode
1. Turn power on.
2. Use service remote control unit and press WAKEUP/SLEEP key. (See page 1-6-1)
Preparing: 2
3. When entering the service mode, one of the number (1, 2 or 4) will display at corners of the screen.
1. To eject the tape, press the STOP/EJECT button
on the unit (or Remote Control).
4. During the service mode, electrical adjustment
mode can be selected by remote control key (service remote control unit).
2. When you want to record during the Service mode,
press the Rec button while depressing SW211
(REC-SAFETY SW) on the Main CBA.
Details are as follows.
Key
Adjustment Mode
MENU
Picture adjustment mode: Press the
MENU button to change from BRT
(Bright), *CNT (Contrast), *COL (Color),
*TNT(Tint) and *V-T. Press CH UP/
DOWN key to display Initial Value.
*Marked items are not necessary to
adjust normally.
0
C-Trap and Y DL Time TV/Y DL Time
EXT/Y SW LPF/Black Stretch Off/ Black
Stretch CONT/C. Angle adjustment
mode: See adjustment instructions
page 1-6-2 and 1-6-3.
1
No need to use.
2
H adjustment mode: See adjustment
instructions page 1-6-2.
3
No need to use.
4
Auto record mode: Perform recording
(15 Sec.)-->Stop-->Rewind (Zero
return) automatically.
5
Head switching point adjustment mode:
See adjustment instructions page 1-66.
6
No need to use.
Q201
(END SENSOR)
SW211
(REC-SAFETY SW)
1-4-1
Q202
(START SENSOR)
MAIN CBA
T5553PFS
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
(1): Order of steps in Procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in Figures.
(2): Parts to be removed or installed.
(3): Fig. No. showing Procedure of Part Location.
(4): Identification of part to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
S=Screw, P=Spring, L=Locking Tab, CN=Connector, *=Unhook, Unlock, Release, Unplug, or
Desolder
2(S-2) = two screws (S-2)
(5): Refer to the following Reference Notes in the
Table.
This flowchart indicates the disassembly steps for the
cabinet parts and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
Caution !
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
[1] Rear Cabinet
[2] Tray Chassis
[3] Deck Unit
Reference Notes in the Table
[4] Main CBA
1. Removal of the Rear Cabinet.
Remove screws 4(S-1) and (S-2).
Caution !
Discharge the Anode Lead of the CRT with the CRT
Ground Wire before removing the Anode Cap.
2. Removal of the Tray Chassis.
Discharge the Anode Lead of the CRT with the
CRT Ground Wire before removing the Anode Cap.
Disconnect the following: Anode Cap, CN505, CRT
CBA, CN601, CN571 and CN801. Then, pull the
Tray Chassis backward.
[5] CRT
2. Disassembly Method
REMOVAL
ID/
LOC.
No.
PART
REMOVE/
*UNHOOK/
Fig.
UNLOCK/RELEASE/ Note
No.
UNPLUG/DESOLDER
[1]
Rear
Cabinet
1, 2 4(S-1), (S-2)
1
[2]
Tray
Chassis
Anode Cap, CN505,
3, 5 CRT CBA, CN601,
CN801, CN571
2
[3]
Deck Unit
7(S-3), (S-4), (S-5),
Desolder (CL201,
3, 5
CL401, CL402,
CL403)
3
[4]
Main CBA
3, 5 5(S-6), (S-7)
4
[5]
CRT
4
5
4(S-8)
↓
↓
↓
↓
↓
(1)
(2)
(3)
(4)
(5)
3. Removal of the Deck Unit.
Remove screws 7(S-3), (S-4) and (S-5). Then, desolder connectors (CL201, CL401, CL402, CL403)
and lift up the Deck Unit.
4. Removal of the Main CBA.
Remove screws 5(S-6) and (S-7). Then, pull up the
Main CBA.
5. Removal of the CRT.
Remove screws 4(S-8) and pull the CRT backward.
1-5-1
T5553DC
S-1
[1] REAR CABINET
S-2
Fig. 1
S-1
S-1
S-1
S-2
S-1
S-1
[1] REAR CABINET
Fig. 2
1-5-2
T5553DC
[2] TRAY CHASSIS
S-3
S-3
[3] DECK UNIT
S-3
S-6
[4] MAIN CBA
S-6
S-6
S-6
S-5
S-4
S-7
Fig. 3
1-5-3
T5553DC
ANODE CAP.
S-8
CRT CBA
S-8
S-8
[5] CRT
S-8
Fig. 4
1-5-4
T5553DC
ANODE
CL502A
CRT
CN505
CL501A
CRT CBA
FOCUS
SCREEN
GND
TO SPEAKER
MAIN CBA
CL403
TO DEGAUSS
COIL
CN801
CN601
AC CORD
CL502B
CL401
CL402
CN571
CL201
CL501B
CYLINDER
ASSEMBLY
FE HEAD
CAPSTAN
MOTOR
ACE HEAD
ASSEMBLY
DECK UNIT
Fig. 5
1-5-5
T5553DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
How to Set up the Service mode:
General Note:
"CBA" is abbreviation for "Circuit Board
Assembly."
Service mode:
1. Use the service remote control unit.
NOTE:
2. Turn the power on.
Electrical adjustments are required after replacing circuit components and certain mechanical parts.
It is important to perform these adjustments only after
all repairs and replacements have been completed.
Also, do not attempt these adjustments unless the
proper equipment is available.
3. Press "WAKE-UP/SLEEP" button on the service
remote control unit.
1. DC 105V (+B) Adjustment
Purpose: To obtain correct operation.
Test Equipment Required
Symptom of Misadjustment: The picture is dark and
unit does not operate correctly.
1. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)
2. AC Milli Voltmeter (RMS)
3. Alignment Tape (FL8A, FL8N), Blank Tape
4. DC Voltmeter
5. Oscilloscope: Dual-trace with 10:1 probe,
V-Range: 0.001~50V/Div,
F-Range: DC~AC-60MHz
6. Frequency Counter
7. Plastic Tip Driver
How to make service remote control
unit:
Test point
Adj. Point
Mode
Input
D613
Cathode
(+B)
C613(-)
(GND)
VR601
---
-----
Tape
M. EQ.
Spec.
---
DC Voltmeter
Plastic Tip Driver
+105±0.5V DC
Note: D613 Cathode (+B), C613(-) (GND),
VR601 --- Main CBA
1. Connect the unit to AC Power Outlet.
1. Prepare remote control unit. (Part No. N0107UD or
N0150UD) Remove 3 screws from the back lid.
(Fig. 1-1)
2. Connect DC Volt Meter to D613 Cathode (+B) and
C613(-) (GND).
3. Adjust VR601 so that the voltage of D613 Cathode
(+B) becomes +105±0.5V DC.
SCREW
2. Initial Setting
Remote control unit (Bottom)
General
Fig. 1-1
1. Enter the Service mode. (See page 1-4-1)
2. Press "VOL p" button on the service remote control
unit. Display changes "C/D," "7F," "FM," "ACCESS
CODE," "9V," and "RC5" cyclically when "VOL p"
button is pressed.
3. To set the following each data value, press "CH o
/ p" buttons on the service remote control unit.
JJ11
2. Remote control unit: Part No. N0107UD
Add J1 (Jumper Wire) to the remote control CBA.
(Fig. 1-2)
Remote control
control CBA
CBA
Remote
7F --- Set to "FF."
Fig. 1-2
1-2
Fig.
FM --- Set to "OFF."
Remote control unit: Part No. N0150UD
Cut off pin 10 of the remote control microprocessor
and short circuit pins 10 and 17 of the microprocessor with a jumper wire.
ACCESS CODE --- Set to "OFF."
9V --- Set to "OFF."
RC5 --- Set to "OFF."
Note: C/D data value does not need to be adjusted at
this moment.
Note: The remote control with the unit cannot be used
as service remote control unit.
1-6-1
T5553EA
3-1. H Adjustment
3-2. C-Trap Adjustment
Purpose: To get correct horizontal position and size of
screen image.
Purpose: To get minimum leakage of the color signal
carrier.
Symptom of Misadjustment: Horizontal position and
size of screen image may not be properly displayed.
Symptom of Misadjustment: If C-Trap Adjustment is
incorrect, stripes will appear on the screen.
Test point
Adj. Point
Mode
Input
Test point
Adj. Point
Mode
Input
R583
CH o / p
buttons
Video
---
J271
(B-OUT)
CH o / p
buttons
---
Color Bar
Tape
M. EQ.
Tape
M. EQ.
Spec.
---
Oscilloscope
Pattern Generator
---
---
Spec.
Frequency Counter 15.734kHz±300Hz
Note: R583 --- Main CBA
Figure
1. Connect Frequency Counter to R583.
2. Set the unit to the VIDEO mode and no input is
necessary. Enter the Service mode.
(See page 1-4-1.)
minimum
3. Operate the unit for at least 20 minutes.
4. Press "2" button on the remote control unit and
select H-Adj mode. (Press "2" button, then display
will change H-Adj and AGC.)
Fig. 2
5. Press "CH o / p" buttons on the remote control
unit so that the display will change "0" to "7."
At this moment, choose display "0" to "7" when the
Frequency counter display is closest to
15.734kHz±300Hz.
Note: J271 (B-Out)--- Main CBA
1. Connect Oscilloscope to J271.
2. Input a color bar signal from RF input.
Enter the Service mode. (See page 1-4-1.)
6. Turn the power off and on again.
3. Press "0" button on the remote control unit and
select C-TRAP mode.
4. Press "CH o / p" buttons on the remote control
unit so that the carrier leakage B-Out (3.58MHz)
value becomes minimum on the oscilloscope.
5. Turn the power off and on again.
1-6-2
T5553EA
3-3. Y DL Time TV/Y DL Time EXT/
Y SW LPF/Black Stretch Off/
Black Stretch CONT/C. Angle
Adjustment
C-TRAP Adjustment (Factory mode)
"0"
button
CH
button
C-TRP 0
Purpose: To get minimum leakage of the color signal
carrier.
C-TRP 1
CH
button
Symptom of Misadjustment: If Y DL Time Adjustment is incorrect, stripes will appear on the screen.
"0" button
Y DL Time TV Adjustment
1. Enter the Service mode. (See page 1-4-1.)
2. Y DL Time TV Adjustment: Press "0" button on
the service remote control unit twice to show "D-T
TV" on the display.
Y DL Time EXT Adjustment: Press "0" button on
the service remote control unit three times to show
"D-T EXT" on the display.
Y SW LPF Adjustment: Press "0" button on the
service remote control unit four times to show "Y
SW" on the display.
Black Stretch Off Adjustment: Press "0" button
on the service remote control unit five times to
show "B-S" on the display.
Black Stretch CONT Adjustment: Press "0" button on the service remote control unit six times to
show "BS2" on the display.
C. Angle Adjustment: Press "0" button on the service remote control unit seven times to show "CANG" on the display.
D-T
CH
button
TV 0
D-T
TV 1
CH
button
"0" button
Y DL Time EXT Adjustment
D-T
EXT 0
CH
button
D-T
EXT 1
CH
button
"0" button
Y SW LPF Adjustment
Y SW
0
CH
button
Y SW
1
CH
button
3. Y DL Time TV Adjustment: Select "2" by pressing
"CH o / p" buttons on the service remote control.
Y DL Time EXT Adjustment: Select "2" by pressing "CH o / p" buttons on the service remote control.
Y SW LPF Adjustment: Select "1" by pressing
"CH o / p" buttons on the service remote control.
Black Stretch Off Adjustment: Select "OFF" by
pressing "CH o / p" buttons on the service remote
control.
Black Stretch CONT Adjustment: Select "0" by
pressing "CH o / p" buttons on the service remote
control.
C. Angle Adjustment: Select "103" by pressing
"CH o / p" buttons on the service remote control.
"0" button
Black Stretch Off Adjustment
B-S
OFF
CH
button
B-S
0
CH
button
"0" button
Black Stretch CONT Adjustment
BS2 0
CH
button
BS2 1
CH
button
"0" button
C. Angle Adjustment
C-ANG 103
CH
button
C-ANG 95
CH
button
1-6-3
T5553EA
4. V. Size Adjustment
6. H. Shift Adjustment
Purpose: To obtain correct vertical height of screen
image.
Purpose: To obtain correct horizontal position and
size of screen image.
Symptom of Misadjustment: If V. Size is incorrect,
vertical height of image on the screen may not be
properly displayed.
Symptom of Misadjustment: Horizontal position and
size of screen image may not be properly displayed.
Test point
Adj. Point
Mode
---
CH o / p
buttons
Tape
M. EQ.
Spec.
---
Pattern Generator
90±5%
Test point
Adj. Point
Mode
Input
---
CH o / p
buttons
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern Generator
90±5%
Input
---
Monoscope
1. Enter the Service mode. (See page 1-4-1.)
Press "8" button on the remote control unit and
select H-P mode.
1. Enter the Service mode. (See page 1-4-1.)
Press "9" button on the remote control unit and
select V-S mode. (Press "9" button then display will
change to V-P and V-S).
2. Input monoscope pattern.
3. Press "CH o / p" buttons on the remote control
unit so that the left and right side of the monoscope
pattern are equal to each other.
2. Input monoscope pattern.
3. Press "CH o / p" buttons on the remote control
unit so that the monoscope pattern is 90±5% of display size and the circle is round.
4. Turn the power off and on again.
7. Cut-off Adjustment
5. V. Shift Adjustment
Purpose: To adjust the beam current of R, G, B, and
screen voltage.
Purpose: To obtain correct vertical position of screen
image.
Symptom of Misadjustment: White color may be
reddish, greenish or bluish.
Symptom of Misadjustment: If V. position is incorrect, vertical position of image on the screen may not
be properly displayed.
Test point
Adj. Point
Mode
Input
---
CH o / p
buttons
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern Generator
90±5%
Test point
1. Enter the Service mode. (See page 1-4-1.)
Press "9" button on the remote control unit and
select V-P mode. (Press "9" button then display will
change to V-P and V-S).
Adj. Point
Mode
Input
Ext.
Black
Raster /
White
Raster
---
Screen-Control
Tape
M. EQ.
Spec.
---
Pattern Generator
See Reference
Notes below
Figure
2. Input monoscope pattern.
3. Press "CH o / p" buttons on the remote control
unit so that the top and bottom of the monoscope
pattern are equal to each other.
PATTERN GENERATOR
EXT. INPUT
Fig. 3
1-6-4
T5553EA
Notes: Screen Control FBT --- MAIN CBA
F.B.T= Fly Back Transformer
Use the Remote Control Unit
8. Sub-Brightness Adjustment
1. Degauss the CRT and allow CRT to operate for 20
minutes before starting the alignment.
Symptom of Misadjustment: If Sub-Brightness is
incorrect, proper brightness cannot be obtained by
adjusting the Brightness Control.
Purpose: To get proper brightness.
2. Set the screen control to minimum position. Input
the Black raster signal from RF input.
3. Enter the Service mode. (See page 1-4-1.)
Dimmed horizontal line appears on the CRT.
4. Press the "VOL p" button.
(Press "VOL p" then display will change CUT OFF/
DRIVE adjustment).
5. Choose CUT OFF/DRIVE mode then press "1" button. This adjustment mode is CUT OFF (R).
Test point
Adj. Point
Mode
Input
---
CH o / p
buttons
---
SYMPTE
7.5IRE
Tape
M. EQ.
Spec.
---
Pattern
Generator
See below
Figure
6. Press the "CH o / p" button until the horizontal line
becomes white.
7. Choose CUT OFF/DRIVE mode then press "2" button. This adjustment mode is CUT OFF (G). Press
"CH o / p" until the horizontal line becomes white.
White
8. Choose CUT OFF/DRIVE mode then press "3" button. This adjustment mode is CUT OFF (B). Press
"CH o / p" until the horizontal line becomes white.
Black
This bar
just
visible
9. Input the White Raster Signal from Video In.
10.Choose CUT OFF/DRIVE mode then press "4."
Adjust the RED DRIVE as needed with the "CH o /
p" buttons to get the following value, X= 286, Y=
294.
Fig. 4
Note: SYMPTE Setup level --- 7 IRE
11.Choose CUT OFF/DRIVE mode then press "5."
Adjust the BLUE DRIVE as needed with the "CH o
/ p" buttons to get the following value, X= 286.
1. Enter the Service mode. (See page 1-4-1.)
Then input SYMPTE signal from RF input.
2. Press MENU button. (Press MENU button then display will change BRT, CNT, COL, TNT and V-T).
Select BRT and press "CH o / p" buttons so that
the bar is just visible (See above figure).
12.Turn the power off and on again.
3. Turn the power off and on again.
1-6-5
T5553EA
9. Focus Adjustment
The following 2 adjustments normally are not
attempted in the field. They should be done
only when replacing the CRT then adjust as a
preparation.
Purpose: Set the optimum Focus.
Symptom of Misadjustment: If Focus Adjustment is
incorrect, blurred images are shown on the display.
12.Purity Adjustment
Test point
Adj. Point
Mode
Input
---
Focus Control
---
Monoscope
Tape
M. EQ.
Spec.
---
Pattern Generator
See below.
Purpose: To obtain pure color.
Symptom of Misadjustment: If Color Purity Adjustment is incorrect, large areas of color may not be
properly displayed.
Test point
Adj. Point
Mode
Input
---
Deflection Yoke
Purity Magnet
---
*Red Color
Tape
M. EQ.
Spec.
---
Pattern Generator
See below.
Note: Focus VR (FBT) --- MAIN CBA
FBT= Fly Back Transformer
1. Operate the unit more than 30 minutes.
2. Face the unit to the East and degauss the CRT
using a Degaussing Coil.
3. Input the monoscope pattern.
Figure
4. Adjust the Focus Control on the FBT to obtain clear
picture.
10. Head Switching Position Adjustment
Purpose: Determine the Head Switching Point during
Playback.
GREEN
RED
Symptom of Misadjustment: May cause Head
Switching Noise or Vertical Jitter in the picture.
BLUE
Fig. 5
Note: Unit reads Head Switching Position automatically and displays it on the screen (Upper Left Corner).
1. Insert the test tape (FL8A, FL8N).
* This becomes RED COLOR if push 7KEY with a
service mode.
2. Set the unit to the stop condition.
1. Set the unit facing east.
3. Enter the Service mode. (See page 1-4-1.)
2. Operate the unit for over 30 minutes before adjusting.
4. Press "PAUSE" button on the remote control unit.
3. Fully degauss the unit using an external degaussing coil.
5. Confirm that indication of OSD is 6.5H.
11. CCS Text Box Location
4. Set the unit to the AUX mode which is located
before CH2 then input a red raster from video in.
When replacing the CRT, the CCS Box might not stay
in appropriate position. Then, replace micro computer.
5. Loosen the screw on the Deflection Yoke Clamper
and pull the Deflection Yoke back away from the
screen. (See Fig. 6.)
Note: This adjustment automatically done by the
microcomputer.
6. Loosen the Ring Lock and adjust the Purity Magnets so that a red field is obtained at the center of
the screen. Tighten Ring Lock. (See Fig. 5,6.)
7. Slowly push the Deflection Yoke toward the bell of
the CRT and set it where a uniform red field is
obtained.
8. Tighten the clamp screw on the Deflection Yoke.
1-6-6
T5553EA
13. Convergence Adjustment
1. Set the unit to the AUX mode which is located
before CH2 then input a Dot or crosshatch pattern.
Purpose: To obtain proper convergence of red, green
and blue beams.
2. Loosen the Ring Lock and align red with blue dots
or Crosshatch at the center of the screen by rotating (RB) C.P. Magnets. (See Fig. 7.)
Symptom of Misadjustment: If Convergence Adjustment is incorrect, the edge of white letters may have
color edges.
Test point
Adj. Point
Mode
Input
---
C.P. Magnet (RB),
C.P. Magnet (RB-G),
Deflection Yoke
---
Dot Pattern
or
Crosshatch
Tape
M. EQ.
Spec.
---
Pattern Generator
See below.
3. Align red / blue with green dots at the center of the
screen by rotating (RB-G) C.P. Magnet.
(See Fig. 8.)
4. Fix the C.P. Magnets by tightening the Ring Lock.
5. Remove the DY Wedges and slightly tilt the Deflection Yoke horizontally and vertically to obtain the
best overall convergence.
6. Fix the Deflection Yoke by carefully inserting the DY
Wedges between CRT and Deflection Yoke.
Figure
CRT
COIL
PURITY
RB
SCREW
RB-G
RING LOCK
SCREW
DY WEDGE
COIL CLAMPER
C.P. MAGNET
CLAMPER
C.P. MAGNET
Fig. 6
DEFLECTION YOKE
C.P. MAGNET (RB)
R
R
G
G
B
B
Fig. 7
C.P. MAGNET (RB-G)
RB
RB
G
G
Fig. 8
1-6-7
T5553EA
1-7-1
DRUM
MOTOR
M
LOADING
MOTOR
PG
SENSOR
CYLINDER ASSEMBLY
CONTROL
HEAD
AC HEAD ASSEMBLY
(DECK ASSEMBLY)
2
1
M
CTL(+)
CTL(-)
ST-SENS.
Q202
CAPSTAN
MOTOR
M
P-ON+12V
P-ON+5V(2)
C-FG
C-F/R
C-CONT
FG-GND
LD-CONT
D-CONT
D-PFG
M-GND
D/L+12V
D/L+15V
SENSOR CBA
(END-SENSOR)
END-SENS.
Q201
CAPSTAN MOTOR
SENSOR CBA
(ST-SENSOR)
CL402
2
1
MAIN CBA
CL201
1
2
3
4
5
6
7
8
9
10
11
12
TIMER+5V
RESET
D/L+12V
DEF+B
P-ON+12V
P-ON+5V
WF3 TP201
CTL
RS201
REMOTE
SENSOR
Q205
SW212
LD-SW
T-REEL
Q206
D203
S-LED
AL+5V
82 LD-CONT
77 D-CONT
90 D-PFG
87 C-FG
66 C-F/R
76 C-CONT
34 RESET
9 ST-SENS.
7 END-SENS.
80 T-REEL
1 LD-SW
SDA 72
74
8
21
26
SP-MUTE 12
A-MUTE 65
D-REC-H 44
C-SYNC
AFT-IN
IF-MUTE
FM/TV-SW
I C-OPEN 45
2
SCL 71
REC LED 23
REC LED 22
P-ON-H 31
P-DOWN 84
YCA-SCLK 70
YCA-CS 69
YCA-SOUT 68
DV-SYNC 13
V-ENV 10
ROTA 15
RF-SW 18
REC-SAFETY 33
97 CTL AMP OUT
95 CTL(+)
94 CTL(-)
14 REMOTE
KEY 1 6
KEY 0 5
IC201
(SERVO/SYSTEM CONTROL)
SW211
REC
SAFETY
P-ON-H
P-DOWN
SW210
D204 REC
SW205,SW207
KEY
SWITCH
SW201 SW204,SW206
KEY
SWITCH
RF-SW
YCA-SCLK
YCA-CS
YCA-SOUT
DV-SYNC
V-ENV
ROTA
SCL
SDA
SP-MUTE
A-MUTE
D-REC-H
SCL
SDA
C-SYNC
AFT-IN
IF-MUTE
FM/TV-SW
7 CS
5 SDA
6 SCL
IC202 (MEMORY)
TO
VIDEO BLOCK
TO
AUDIO BLOCK
TO
CHROMA /TUNER
BLOCK
AL+5V
TO
POWER SUPPLY
BLOCK
Servo/System Control Block Diagram
BLOCK DIAGRAMS
T5553BLS
1-7-2
VIDEO (L) HEAD
VIDEO (R) HEAD
(DECK ASSEMBLY)
TO
SERVO/SYSTEM
CONTROL BLOCK
JK701
FRONT V-IN
TO
CHROMA/TUNER
BLOCK
VIDEO
DV-SYNC
YCA-SCLK
YCA-SOUT
YCA-CS
LINE-VIDEO
TU-VIDEO
WF5
TP301
V-OUT
LINE
TUNER
VIDEO
AGC
SERIAL
I/F
24 DV-SYNC
53
54
55
30
42
32
WF4
1
2
3
R P
FBC
QV/QH
6dB
AMP
26
TO
SERVO/SYSTEM
CONTROL BLOCK
CL401
V(R)
V-COM
V(L)
IC401
(VIDEO SIGNAL PROCESS/ HEAD AMP)
Q401
BUFFER
TP202
RF-SW
ROTA
RF-SW
V-ENV
WF1
Y/C
MIX
37
SP
HEAD
AMP
36
57 C-ROT/RF-SW
59 V-ENV
74
73
72
VCA
MAIN CBA
39
CHROMINANCE
SIGNAL PROCESS
YNR/COMB FILTER
CCD 1H
DELAY
Q402
BUFFER
34
CLAMP
REC VIDEO SIGNAL
VXO
49
WF2
70
69
P
R
LUMINANCE
SIGNAL PROCESS
50
X401
3.58MHz
PB VIDEO SIGNAL
WF6
TP402
V-ENV
14
MODE: SP/REC
Video Block Diagram
T5553BLV
SDA
SCL
TU-AUDIO
1-7-3
FULL
ERASE
HEAD
FE HEAD UNIT
AUDIO
ERASE
HEAD
AUDIO
HEAD
AC HEAD ASSEMBLY
BLOCK DIAGRAM FOR SECTION 2 (DECK MECHANISM)
JK702
FRONT A-IN
TO
SERVO/SYSTEM
CONTROL BLOCK
TO
CHROMA/TUNER
BLOCK
21
26
14
15
24
SERIAL
I/F
CL403
2 FE-H
1 FE-H-GND
3
4
6
5
LINE
CL402
A-PB/REC
A-COM
AE-H
AE-H/FE-H
VCR
TUNER
AUDIO
ATT
WF8
TP401
A-OUT
Q874
Q873
32
IC301(CHROMA/DEFLECTION SIGNAL PROCESS)
Q875
BIAS
OSC
Q872
P-ON+5V
P-ON+5V
Q871
6
2
SP-MUTE
MUTE
/STANDBY
AMP
6
11
SP/LP-ON
AUTO
BIAS
5
EQ
AMP
8
4
3
78
WF9
2
9
P
R
REC
AMP
ALC
CN801
SPEAKER
SP-GND
Mode : SP/REC
TUNER
LINE
76
TO
SERVO/SYSTEM
CONTROL BLOCK
REC-AUDIO SIGNAL
IC401 (AUDIO SIGNAL PROCESS)
1
IC801 (AMP)
MAIN CBA
PB-AUDIO SIGNAL
LINE
AMP
CL802
1
2
58
MUTE
10
A-MUTE
D-REC-H
SP801
SPEAKER
JK801
EARPHONE JACK
TO
SERVO/
SYSTEM
CONTROL
BLOCK
Audio Block Diagram
T5553BLA
TO
SERVO/SYSTEM
CONTROL BLOCK
1
5
4
8
IF 11
AGC
SDA
SCL
FSC
TU001
SCL
SDA
C-SYNC
AFT-IN
1-7-4
WF10
35
34
9
8
WF18 V-SYNC 59
WF17 H-SYNC 58
16
INTELLIGENT
MONITORING
6
V-SYNC
PROCESS
CIRCUIT
SYNC
SEPARATION
SERIAL
I/F
14
15
12
11
10
13
OSD-R
OSD-G
OSD-B
OSD-BLK
AFT
VCO
VIDEO
DET
4
IF AGC DET
H-SYNC
PROCESS
CIRCUIT
LPF
4.5MHz
FILTER
CF032
4.5MHz
TRAP
CF031
OSD MIX/RBG MATRIX/
BLIGHT/DRIVE AMP/
HV BLANKING
CHROMA
SIGNAL
PROCESS
CIRCUIT
LUMA
SIGNAL
PROCESS
CIRCUIT
7
2
CHROMA
BPF
WF7
CHROMA
TRAP
IC301 (CHROMA/DEFLECTION SIGNAL PROCESS)
RF
AGC
14
31
AMP
VIF
AMP
IC001 (IF SIGNAL PROCESS)
11
13
16
17
64
63
62
60
CV-IN 56
IC201
(SYSTEM CONTROL/OSD)
SAW
FILTER
SF001
FM
DET
EQ
AMP
FILTER
TUNING
VCR
LINE
TUNER
VCR
LINE
TUNER
REC-AUDIO SIGNAL
VXCO
40
41
5
2
3
4
18
23
25
20
6
9
WF11
X301
3.58MHz
VCO F/B
AF
AMP
1
REC VIDEO SIGNAL
TP302
AFC
TO VIDEO BLOCK
Mode : SP/REC
AFC
H-DRIVE
ACL
V-RAMP-NF
V-DRIVE
TO
CRT/H.V. BLOCK
CL502A
TO
VIDEO BLOCK
TO
CRT/H.V. BLOCK
VIDEO
LINE-VIDEO
TO
SERVO/ SYSTEM
FM/TV-SW CONTROL BLOCK
IF-MUTE
TU-AUDIO TO AUDIO BLOCK
TU VIDEO
CL502B
2 RED
3 GREEN
4 BLUE
MAIN CBA
PB VIDEO SIGNAL
Chroma/Tuner Block Diagram
T5553BLC
1-7-5
TO
CHROMA/TUNER
BLOCK CL502B
TO
CHROMA/TUNER BLOCK
TO
POWER SUPPLY BLOCK
RED
GREEN
BLUE
V-DRIVE
H-DRIVE
AFC
ACL
V-RAMP-NF
DEF+B
+B
CL502A
2
3
4
WF12
H.DRIVE
Q572
Q571
H.OUTPUT
T572
4
3
5
1
11
S
HV
F
CRT CBA
GREEN AMP
Q521
6
AMP
SCREEN VR
FOCUS VR
WF14
MAIN CBA
6
9
7
10
8
Q511
RED AMP
T571 F.B.T.
1
7
FOCUS
SCREEN
ANODE
VCC
2
5
WF15
CL501B
3 HEATER
1 +160V
3
PUMP
UP
THERMAL
PROTECTION
IC551 (V-DEFLECTION CONTROL)
REC VIDEO SIGNAL
BLUE AMP
Q531
CL501A
3
1
WF16
PB VIDEO SIGNAL
1
3
4
5
CN505
GND
V501
R
CRT
G
B
HEATER
FOCUS
SCREEN
GND
ANODE
HDRIVE
VDRIVE
L551
DEFLECTION-YOKE
JK501
CN571
WF13
Mode : SP/REC
CRT/H.V. Block Diagram
T5553BLCRT
DG601
DEGAUSSING
COIL
W601
CN601
L601
Q601
1-7-6
LIMITER
Q602
PS601
LINE
FILTER
SWITCHING
F601
4A/125V
4A/125V
HOT CIRCUIT. BE CAREFUL.
BRIDGE
RECTIFIER
D603 - D606
HOT
CAUTION !
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
1
2
4
3
IC601
ERROR
VOLTAGE DET
1
2
4
6
T601
4A/125V
8
7
9
FEED
BACK
Q604
10
11
12
COLD
+B ADJ.
VR601
Q610
Q611
Q608
IC602
Q613
Q605
+8V REG.
+5V REG.
+5V REG.
+5V REG.
+5V REG.
MAIN CBA
Q607
Q606
27
P-ON-ON
IC301
+5.7V
REGULATOR
Q612
30
P-ON-H
(TO PIN31 OF IC201)
P-DOWN
(TO PIN84 OF IC201)
TIMER+5V
P-ON+12V
AL+5V
P-ON+8V
AL+12V
P-ON+5V
P-ON+5V
P-ON+5V
P-ON+5V
DEF+B
AL+33V
+B
NOTE :
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Q609
+5V REG.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,
REPLACE ONLY WITH SAME TYPE 4 A, 125V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE 4A, 125V.
Power Supply Block Diagram
T5553BLP
MECHANICAL TROUBLE INDICATOR
1, Each Malfunction Indication
POWER SAFETY
If the MONITOR is turned ON right after the Mechanical Malfunction occurs or POWER SAFETY is turned
ON, display the following character to show Malfunction after the EJECT display.
1) POWER SAFETY 2
Immediately preceding
Malfunction
If P-SAFETY 2 port becomes continuously 2.5V or
less for 120 msec. (4 times 40 msec. interval) when
P-ON-H port is ON, the unit shall be assumed to be
the Power Malfunction 2 and immediately turn OFF
the POWER/MONITOR and switch over the
Mechanical Malfunction mode with POWER OFF.
(Shall not unload)
(To return from this mode shall become possible
only by POWER Key as in the case of the Mechanical Malfunction).
* However the POWER SAFETY 2 function shall be
disabled during 500 msec. right after the P-ON-H
turns ON.
2) POWER SAFETY 3
Display character
REEL Malfunction
R
DRUM Malfunction
D
CASSETTE LOADING Malfunction
C
TAPE LOADING Malfunction
T
P-SAFETY 2
2
P-SAFETY 3
3
P-SAFETY 1
1
If P-SAFETY 3 port becomes continuously 2.5V or
over for 120 msec. (4 times 40 msec. interval)
when MONITOR is ON, P-SAFETY 3 function is
available. After that, if P-SAFETY 3 port becomes
continuously 2.5V or less for 120 msec. (4 times 40
msec. interval), the unit shall be assumed to be the
Power Malfunction 3 and immediately turn OFF the
POWER/MONITOR and switch over the Mechanical Malfunction mode with POWER OFF.
(Shall not unload)
(To return from this mode shall become possible
only by POWER Key as in the case of the Mechanical Malfunction).
Example: If REEL Malfunction
EJECT R
2, Each Malfunction evaluation
method
P-SAFETY 1 protect
If P-SAFETY 1 port becomes continuously 2.5V or
more for 120 msec. (4 times 40 msec. interval), the
unit shall immediately turn OFF the POWER/MONITOR and switch over to the Mechanical Malfunction
mode with POWER OFF.
(To return from this mode shall become possible only
by POWER Key as in the case of the Mechanical Malfunction).
1-7-7
T5553MTI
Mechanical Malfunction determination
4) Countermeasure for CASSETTE LOADING Malfunction
1) REEL Malfunction detection
a) CASSETTE IN operating Malfunction
Countermeasure for REEL and CAPSTAN motor
rotation malfunction (Except CASSETTE LOADING function)
After the Malfunction detection with REEL/CAPSTAN sensor, the unit shall switch over to STOP
(B) and be REEL Mechanical Malfunction.
If LD-SW does not go to SB position after a lapse
of 5 sec. or more from the CASSETTE insertion
start, the unit starts the CASSETTE OUT operation.
After switch over to CASSETTE OUT operation and
then a laps of 5 sec. or more from the CASSETTE
OUT operation start, if LD-SW does not go to the
EJ position or if START Sensor and END Sensor
does not turn "ON" at the EJ position, the unit
starts again to insert CASSETTE.
(However in S-INH state, the START/END Sensor
shall be disabled).
a) If the T-REEL pulse is not impressed after a lapse
of 5 sec. at SP, 10 sec. at LP, 14 sec. at SLP, or
more in the REEL Rotation Mode like PLAY/REC,
FS/RS Mode, and the T-REEL or S-REEL pulse is
not impress after a lapse of 4 sec. or more in REEL
Rotation Mode of FF/REW, it shall be assumed to
stop the rotation and switch over to STOP (B) position, then POWER be turned OFF and the unit be
REEL Mechanical Malfunction. (T-REEL and SREEL for the models on S-REEL and only T-REEL
for other models)
b) CASSETTE OUT operating Malfunction
After a lapse of 5 sec. or more from CASSETTE
OUT operation start, if LD-SW does not go to the
EJ position or if START Sensor and END Sensor
does not turn "ON" at the EJ position, the unit
starts to insert CASSETTE.
(However in S-INH state, the START/END Sensor
shall be disabled).
b) If the C-FG pulse is not impressed for a lapse of 1
sec. or more during the CAPSTAN MOTOR rotation, it shall be MOTOR Rotation Malfunction
(REEL Malfunction).
2) DRUM Malfunction detection
Detect the DRUM rotation at the D-FG input terminal.
If the variation of D-FG input level is not detected
for a lapse of 1 sec. or more when D-CONT is "H",
it shall be assumed to be Rotation Malfunction and
be DRUM Malfunction.
When detect Drum Malfunction, POWER shall be
turned OFF after the unit switches over to STOP
(B) Mode.
When the unit switches over to CASSETTE insertion at CASSETTE IN or CASSETTE OUT Malfunction, if LD-SW does not go to the SB position
after a lapse of 5 sec. or more from CASSETTE
insertion start, the function shall immediately be
stopped and POWER be turned OFF, and the unit
be CASSETTE LOADING Malfunction.
c) When POWER is turned ON, if the CL position or
GC position cannot be detected after 5 sec. LDREV operation and 5 sec. LD-FWD operation, the
function shall immediately be stopped and POWER
be turned OFF, and the unit be CASSETTE LOADING Malfunction.
3) Countermeasure for TAPE LOADING Malfunction
Detect the Malfunction with the LOADING Switch.
a) TAPE LOADING Malfunction
If LD-SW does not go to the established position
after a lapse of 7 sec. or more from TAPE LOADING or TAPE UNLOADING start, the LOADING
function shall immediately be stopped and POWER
be turned OFF, and inform the Timer about the
LOADING Mechanical Malfunction.
d) When POWER is turned ON without CASSETTE
(EJ position) and LD-SW is monitored all the time,
if the CL or GC position is detected continuously for
1 sec. or more, the POWER shall be turned OFF
and the unit be CASSETTE LOADING Malfunction.
b) LD-SW Position Malfunction at each mode
Countermeasure for Mechanical
Malfunction
When the unit operates at each mode, even if the
LD-SW position changes from the established one
in its mode, it keeps the function according to its
mode.
If the unit detects Mechanical Malfunction, turn the
POWER OFF. If the unit is Mechanical Malfunction,
Key input except POWER key shall be disabled and
CASSETTE insertion disabled. When POWER Key is
entered, the POWER is turned ON and the unit
switches over the EJECT Mode. (Return with POWER
ON)
1-7-8
T5553MTI
Power Supply Trouble Shooting Guide
It is highly recommended that a variable isolation
transformer which can monitor current be used.
(Alternatively a variable AC source which monitors
current will do). Read directions below before
power is added!
Voltage approx. 5Vp-p
0V
T=Approx. 6 to 14 sec
Oscilloscope setting: 1V/DIV.
2 sec./DIV
CHECK
Repair method
Fig.1
Repair method #1
Check Fuse (F601) is blown
out or not.
If fuse is blown out,
do repair method #1
(Power must be off)
YES
Short circuit in the secondary side. check diode D613,
D614, D616, D617 and D618, switching transistor
(Q601), control transistor (Q602), diode and resistor
replace as necessary.
#1
NO
Check whether the primary
rectifying DC of the Switching
NO
power supply has an output.
(Reading should be about 168V.
Disconnect 105V diode (D613), 25V diode (D614), 8V
diode (D616), 12V diode (D617), 12V diode (D618)
and Check the load continuity of 105V line, 25V line,
8V line, 12V line through a tester (resistance range).
#2
If the tester indicates a lower resistance value around
0 ohm, the line is short-circuited.
YES
Voltage of the 105V line
higher than normal?
YES
Before repairing the switching power supply, find out
the short-circuited area of such line and repair it.
#3
If the tester does not indicate any low resistance value
(around 0 ohm), no load is short-circuited and there is
no problem.
NO
The transformer of the power
supply makes a higher sound
or the oscillation wave form is
abnormal.
(E.g. intermittent oscillation)
YES
Connect the positive probe of
#4
oscilloscope to the pin 16 of
T601, then connect the negative
probe to the pin 12. Observe the
waveform and check to see if
the waveform is out of limit of
value shown in Fig.1.
Check for any defective parts while the secondary rectifying diodes are disconnected (D613, D614, D616,
D617 and D618) perform a diode check in both forward and reverse directions through a tester.
NO
There is no problem on the
SW power supply
1-7-9
T5553TR1
Repair method #2
Check the primary rectifying diodes (D603-D606) as
possible problems. Remove the above mentioned
parts and check them. Perform check according to the
step 1 and 2 of repair method #1 and check for defects
following parts, then if necessary replace with factory
originals.
R602 is open or not.
Q601, Q602, D607, D608 and D611 are short or not.
Repair method #3
The feedback circuit which is monitored by the output
of D613 105V may not work and this may be regarded
as a possible cause, remove IC601 (Photo Coupler),
diode (D620) and transistor (Q604) check for defects.
Repair method #4
Check control circuitly which is connecting to Pin 2
and 1 of Switching Transformer T601.
1-7-10
T5553TR1
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS
Standard Notes
Note:
1. Do not use the part number shown on these drawings for ordering. The correct part number is shown
in the parts list, and may be slightly different or
amended since these drawings were prepared.
Warning
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage,
etc. Replacement parts that have these special safety
characteristics are identified in this manual and its
supplements; electrical components having such features are identified by the mark " # " in the schematic
diagram and the parts list. Before replacing any of
these components, read the parts list in this manual
carefully. The use of substitute replacement parts that
do not have the same safety characteristics as specified in the parts list may create shock, fire, or other
hazards.
2. All resistance values are indicated in ohms (K=103,
M=106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF
(P=10-6µF).
5. All voltages are DC voltages unless otherwise
specified.
Capacitor Temperature Markings
Mark
Capacity
change rate
Standard
temperature
Temperature
range
(B)
±10%
20°C
-25~+85°C
(F)
+30 -80%
20°C
-25~+85°C
(SR)
±15%
20°C
-25~+85°C
(Z)
+30 -80%
20°C
-10~+70°C
Capacitors and transistors are represented by the following symbols.
CBA Symbols
(Top View) (Bottom View)
+
Electrolytic Capacitor
(Bottom View)
Transistor or Digital Transistor
E
C
B
Schematic Diagram Symbols
(Top View)
(Top View)
PNP Transistor
NPN Transistor
ECB
ECB
(Top View)
(Top View)
PNP Digital
Transistor
NPN Digital Transistor
ECB
Digital Transistor
ECB
1-8-1
SC_1
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective
before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the
power supply circuit to fail.
3. Note:
(1) Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts
list, and may be slightly different or amended since the drawings were prepared.
(2) To maintain original function and reliability of repaired units, use only original replacement parts which are listed
with their part numbers in the parts list section of the service manual.
4. Wire Connectors
(1) Prefix symbol "CN" means "connector" (can disconnect and reconnect).
(2) Prefix symbol "CL" means "wire-solder holes of the PCB" (wire is soldered directly).
5. Note: Mark "•" is a leadless (chip) component.
6. Mode: SP/REC
7. Voltage indications for PLAY and REC modes on the schematics are as shown below:
1
2
5.0
The same voltage for
both PLAY & REC modes
3
5.0
(2.5)
PLAY mode
REC mode
Unit: Volts
Indicates that the voltage
is not consistent here.
8. How to read converged lines
3
1-D3
1-B1
AREA D3
Distinction Area
2
Line Number
(1 to 3 digits)
1
Examples:
1. "1-D3" means that line number "1" goes to area "D3".
2. "1-B1" means that line number "1" goes to area "B1".
AREA B1
1-D3
A
B
C
D
9. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
1-8-2
SC_2
Main 1/5 Schematic Diagram
A4
B4
C4
D4
F4
E4
MAIN 1/5
Ref No.
Position
ICS
C-2
IC201
D-1
IC202
TRANSISTORS
B-1
Q205
D-3
Q206
CONNECTOR
F-4
CL201
TEST POINTS
TP201
B-4
TP202
B-2
A3
B3
C3
D3
E3
F3
A2
B2
C2
D2
E2
F2
A1
B1
C1
D1
E1
F1
1-8-3
1-8-4
T5553SCM1
Main 2/5 Schematic Diagram
REC Video Signal
REC Audio Signal
G4
H4
I4
J4
PB Video Signal
PB Audio Signal
L4
K4
MAIN 2/5
Ref No.
Position
ICS
G3
H3
I3
J3
K3
L3
G2
H2
I2
J2
K2
L2
G1
H1
I1
J1
K1
L1
1-8-5
1-8-6
H-2
IC401
K-4
IC801
TRANSISTORS
K-2
Q401
K-3
Q402
H-2
Q871
Q872
H-1
G-1
Q873
Q874
G-1
Q875
H-1
CONNECTORS
G-3
CL401
L-1
CL402
G-1
CL403
K-4
CN801
TEST POINTS
K-2
TP301
J-1
TP401
TP402
J-1
T5553SCM2
Main 3/5 Schematic Diagram
PB Video Signal
PB Audio Signal
REC Video Signal
REC Audio Signal
M4
N4
O4
P4
Q4
R4
MAIN 3/5
Ref No.
Position
ICS
Q-2
IC001
M-2
IC301
TRANSISTOR
N-1
Q301
TEST POINT
TP302
O-1
M3
N3
O3
P3
Q3
R3
M2
N2
O2
P2
Q2
R2
M1
N1
O1
P1
Q1
R1
1-8-7
1-8-8
T5553SCM3
Main 4/5 Schematic Diagram
CAUTION !
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE
MÊME TYPE DE 4A, 125V.
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
MAIN 4/5
Ref No.
Position
ICS
W-2
IC601
T-3
IC602
TRANSISTORS
X-2
Q601
W-2
Q602
V-2
Q604
Q605
U-2
U-3
Q606
Q607
U-2
Q608
T-2
Ref No.
Position
TRANSISTORS
T-2
Q609
T-2
Q610
T-1
Q611
S-2
Q612
S-1
Q613
CONNECTOR
CN601
X-1
VARIABLE RESISTOR
VR601
V-2
VOLTAGE CHART (Power off mode)
2
3
Ref. No.
1
10.0
0
IC601
11.0
1
2
Ref. No.
3.0
0
IC602
S
D
Ref. No.
0
137.0
Q601
E
C
Ref. No.
0
3.2
Q602
6.7
9.9
Q604
0
7.9
Q605
8.9
8.8
Q606
0
0
Q607
0
3.0
Q608
5.8
8.2
Q609
0.9
5.6
Q610
0.1
3.0
Q611
Q612
5.1
5.1
0
3.0
Q613
4
16.0
3
1.8
G
1.8
B
0
7.8
0
8.2
0.7
0
6.5
1.4
0
1.9
0
S3
T3
U3
V3
W3
X3
S2
T2
U2
V2
W2
X2
S1
T1
U1
V1
W1
X1
1-8-9
1-8-10
T5553SCM4
Main 5/5 & CRT Schematic Diagram
MAIN 5/5
Ref No.
CRT
Ref No.
Position
TRANSISTORS
CC-2
Q511
CC-2
Q521
CC-2
Q531
CONNECTORS
BB-3
CL501A
BB-2
CL502A
CN505
DD-2
Position
IC
Y-3
IC551
TRANSISTORS
AA-2
Q571
Z-3
Q572
Z-2
Q591
CONNECTORS
BB-3
CL501B
BB-2
CL502B
CN571
Z-3
REC Video Signal
PB Video Signal
Y3
Z3
AA3
BB3
CC3
DD3
Y2
Z2
AA2
BB2
CC2
DD2
Y1
Z1
AA1
BB1
CC1
DD1
1-8-11
1-8-12
T5553SCM5
Sensor CBA Top View
Main CBA Top View
CAUTION !
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, check to see that all components in the power supply circuit
are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply
WF3
WF1
circuit to fail.
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
TP201
CTL
TP202
RF-SW
TO SENSOR CBA
(END-SENSOR)
J271
B-OUT
4A/125V
WF6
WF5
TP402
V-ENV
TP301
V-OUT
WF8
TP401
A-OUT
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE
MÊME TYPE DE 4A, 125V.
BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER
SUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED.
ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUT
SLOWLY, WHEN TROUBLESHOOTING THIS TYPE POWER SUPPLY
CIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.
BHB300F01014-A
BHB300F01014-B
Position
ICS
CL602 B
C650
B
CL301
C613 GND
(+B Adjustment)
VR601
+B ADJ
D613 Cathode
(+B Adjustment)
R583
(H Adjustment)
1-8-13
MAIN CBA
Ref No.
TO SENSOR CBA
(START-SENSOR)
1-8-14
D-4
IC001
A-3
IC201
B-3
IC202
B-4
IC301
C-3
IC401
D-2
IC551
IC601
E-3
D-2
IC602
A-1
IC801
TRANSISTORS
A-4
Q205
B-3
Q206
A-4
Q301
B-3
Q401
B-3
Q402
D-1
Q571
C-1
Q572
C-1
Q591
E-3
Q601
E-3
Q602
E-3
Q604
D-3
Q605
D-3
Q606
D-2
Q607
D-3
Q608
C-4
Q609
C-4
Q610
C-4
Q611
D-3
Q612
D-4
Q613
C-3
Q871
D-3
Q872
C-2
Q873
C-3
Q874
C-2
Q875
CONNECTORS
C-1
CL201
C-3
CL401
C-2
CL402
C-4
CL403
D-1
CL501B
D-3
CL502B
D-1
CN571
D-4
CN601
B-4
CN801
TEST POINTS
B-4
TP201
C-4
TP202
C-4
TP301
B-4
TP302
D-4
TP401
C-4
TP402
VARIABLE RESISTOR
VR601
E-2
BT5500F01011
Main CBA Bottom View
CAUTION !
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
WF7
PIN 7
OF IC001
4A/125V
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE
MÊME TYPE DE 4A, 125V.
WF9
PIN 9
OF IC401
BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER
SUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED.
ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUT
SLOWLY, WHEN TROUBLESHOOTING THIS TYPE POWER SUPPLY
CIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.
WF11
PIN 41
OF IC301
WF10
PIN 9
OF IC301
WF2
PIN 49
OF IC401
WF18
PIN 59
OF IC201
WF17
PIN 58
OF IC201
WF4
PIN 32
OF IC401
WF13
PIN 5
OF CN571
WF12
Q571
Collector
1-8-15
1-8-16
BT5500F01011
CRT CBA Top View
CRT CBA Bottom View
CRT CBA
Ref No.
Position
TRANSISTORS
B-1
Q511
B-1
Q521
A-1
Q531
CONNECTORS
A-1
CL501A
B-1
CL502A
CN505
B-2
WF15
Q521
Collector
1-8-17
WF14
Q511
Collector
1-8-18
WF16
Q531
Collector
BT5500F01011
1DIV: 0.2V 0.1µsec
IC401 PIN 49
1DIV: 1V 10msec
TP201 CTL
1DIV: 0.25V 20µsec
IC401 PIN 32
WF3
WF4
1DIV: 2V
5msec
TP202 RF-SW
WF2
WF1
1DIV: 0.5V 20µsec
TP301 V-OUT
1-9-1
1DIV: 0.2V 0.5msec
IC001PIN 7
1DIV: 0.5V 0.5msec
TP401 A-OUT
WF7
WF8
Upper: WF6 Lower: WF1
1DIV: 0.2V 2DIV: 5V 5msec
TP402 V-ENV
WF5
1DIV: 0.5V 0.5msec
IC401 PIN 9
WF12 1DIV: 200V 20µsec
Q571 COLLECTOR
WF11 1DIV: 1V 20µsec
IC301 PIN41
5msec
WF10 1DIV: 2V
IC301 PIN 9
WF9
WF16 1DIV: 20V 20µsec
Q531 COLLECTOR
WF15 1DIV: 20V 20µsec
Q521 COLLECTOR
WF14 1DIV: 20V 20µsec
Q511 COLLECTOR
5msec
WF13 1DIV: 10V
CN571 PIN 5
WF18 1DIV: 1V
5msec
IC201 PIN 59
WF17 1DIV: 1V 20µsec
IC201 PIN 58
WAVEFORM NOTES
INPUT: NTSC COLOR BAR SIGNAL (WITH 1kHz AUDIO SIGNAL)
BRIGHTNESS, COLOR AND TINT CONTROLS: CENTER POSITION
CONTRAST CONTROL: APPROX 70%
VOLTAGES SHOWN ARE RANGE OF OSCILLOSCOPE SETTING.
WAVEFORMS
Z13WF
CRT
1-10-1
W601
VD
HD
D.Y.
ANODE
GND
1
2
CN601
CN571
1
2
3
4
5
SCREEN
CN505
FOCUS
1
2
3
CL501A
+160V
GND
HEATER
T571
FBT
1
2
3
4
CL502A
GND
RED
GREEN
BULE
CRT CBA
BT5500F01011
CL802
MAIN CBA
BT5500F01011
SENSOR CBA
(ST-SENSOR)
BHB300F01014A,B
SENSOR CBA
(END-SENSOR)
BHB300F01014A,B
SP801
SPEAKER
CL502B
GND
RED
GREEN
BLUE
CL501B
1 +160V
2 GND
3 HEATER
1
2
3
4
CN801
1 SPEAKER
2 SP-GND
CL403
FE-H-GND
FE-H
CL402
AE-H
AE-H/FE-H
A-COM
A-PB/REC
CTL(+)
CTL(-)
CL401
V(L)
V-COM
V(R)
CL201
P-ON+12V
P-ON+5V(2)
C-FG
C-F/R
C-CONT
FG-GND
LD-CONT
D-CONT
D-PFG
M-GND
D/L+12V
D/L+15V
1
2
6
5
4
3
2
1
3
2
1
1
2
3
4
5
6
7
8
9
10
11
12
CAPSTAN MOTOR
M
WIRING DIAGRAM FOR SECTION 2
(DECK MECHANISM)
VIDEO
(R) HEAD
FULL ERASE HEAD
FE HEAD
AC HEAD ASSEMBLY
CONTROL HEAD
AUDIO HEAD
AUDIO ERASE
HEAD
DRUM
MOTOR
VIDEO
(L) HEAD
M
PG
SENSOR
CYLINDER ASSEMBLY
LOADING
MOTOR
WIRING DIAGRAM
T5553WI
SYSTEM CONTROL TIMING CHARTS
Chart 1
EJ
0.2S
CL SB
CASS.LOAD
LD-FWD
0.2S
SB
0.2S
STOP(B)
POWER
0.2S
LD-FWD
1.2S
after channel setting
+100mS(NTSC)
+620mS(PAL)
TL
0.2S
FB
TL
0.2S
0.4S
STOP
0.2S
SM
SF
LD-FWD
0.2S
0.2S
LD-FWD
SF SM AL
AU
LD-REV
0.5S
SM
40mS
0.4S
AU
LD-REV
20mS
0.2S
STOP(A)
AL
AU
0.2S
0.2S
PLAY
0.8S
0.3S
PLAY
SS
LD-FWD
REW
RS
RS
0.3S
RS1(RS2)
0.2S
AL
SS AU
LD-REV
FF
FS
LD-FWD
AL
1.0S
FS1(FS2)
PLAY
PLAY
PLAY
5.0S
STILL
STILL
1.0S
0.12S
0.3S
PLAY
PLAY
AU
0.4S
SM
40mS
STOP
0.8S
STOP(A)
STOP
/EJECT
LD-REV
PAUSE
OFF
SP MODE LP/SLP MODE
>5.0S
NOISE
CANCEL
PAUSE
ON
STILL
NTSC 80mS 6mS 240mS 6mS
PAL 80mS 6mS 160mS 6mS
PAUSE
PLAY
20mS
0.2S
1. EJECT (POWER OFF) -> CASSETTE IN (POWER ON) -> STOP(B) -> STOP(A) -> PLAY -> RS -> FS -> PLAY -> STILL(N-CANCEL) -> PLAY -> STOP(A)
PIN NO.
1
LD-SW
CL/SS
EJ
AU
RS
SF
SM
TL
FB
AL
SB
82
LD-CONT
ON
ON
"Z"
C-DRIVE
66 C-F/R
DRUM
ROTATION
31 P-ON
65 A-MUTE-H
D-PB-H
44 D-REC-H
DISPLAY
ST-S
"OFF"
POWER
-OFF
NOISE
CANCEL
PAUSE
ON
PAUSE
OFF
STILL
PLAY
LD-FWD
REC
SFT-SW
LD-REV
T5553TI
1-11-1
EJECT
Chart 2
SM
FB SM
SF
LD-FWD
FF
SF
REV
1.0S
AU SM
STOP
0.4S
LD-REV
40mS
SM AL
AU
0.5S
LD-FWD
STOP(A)
LD-REV
SF TL
FB
REW
20mS
0.2S
0.2S
FB SM
SF
LD-FWD
REW
SF
LD-FWD
LD-REV
40mS
0.4S
SM AL AU SM
AU
0.5S
STOP
0.2S
STOP(A)
REC
AU
AL
0.2S
1.0S
20mS
LD-FWD
REC
LD-FWD
SS RS
2.5S Short REV
LD-REV
AL AU
SS
0.2S
REC PAUSE
LD-FWD
AL
1.2S
1.5S
SS RS
REC PAUSE REC or
PAUSE
REC
STOP
/EJECT
LD-FWD
REC
LD-REV
AU SM
1.5S(NTSC)
1.0S(PAL)
0.4S
AL
0.2S
LD-FWD
0.5S
AL AU
SS
LD-REV
40mS
LD-REV
20mS
SB
0.2S
LD-REV
FB TL
SF
STOP
/EJECT
0.2S
STOP(A)
STOP
0.5S
0.2S
0.5S
0.1S
CL EJ
EJECT
ST-S
"ON"
CASS. UNLD
STOP
/EJECT
0.2S
REW
LD-REV
1.0S
STOP
/EJECT
0.2S
FF
SF TL
FB
0.2S
REC
PAUSE
2. STOP(A) -> FF -> STOP(A) -> REW -> STOP(A) -> REC -> PAUSE -> PAUSE or REC -> STOP(A) -> EJECT
PIN NO.
1
LD-SW
CL/SS
EJ
AU
RS
SF
SM
TL
FB
AL
SB
82
LD-CONT
ON
ON
"Z"
C-DRIVE
66 C-F/R
DRUM
ROTATION
31 P-ON
65 A-MUTE-H
D-PB-H
44 D-REC-H
DISPLAY
FF
LD-REV
T5553TI
1-11-2
STOP(A)
STOP
IC PIN FUNCTION DESCRIPTIONS
IC201 (TV/VCR Micro Controller)
“H” ≥ 4.5V, “L” ≤ 1.0V
Pin IN/
No. OUT
1
IN
2
-
3
Signal
Name
Function
Pin IN/
No. OUT
32
-
33
Signal
Name
Function
NU
Not Used
IN
RECSAFETY
Record Protection Tab
Detection
LD-SW
Loading Switch Input
NU
Not Used
34
IN
RESET
System Reset Signal
(Reset=”L”)
IN
P-SAFETY 2
Power Supply Failure
Detection 2
35
IN
XC-IN
Sub Clock 32 kHz
4
IN
Power Supply Failure
P-SAFETY 3
Detection 3
37
-
5
IN
KEY0
Key 0 Input
38
IN
6
IN
KEY1
Key 1 Input
7
IN
END-SENS End-Sensor
8
IN
AFT-IN
AFT Input
9
IN
ST-SENS
Start-Sensor
10
IN
V-ENV
Video Envelope Input
11
-
NU
Not Used
12
OUT SP-MUTE
Speaker Mute Output
13
OUT DV-SYNC
Artificial V-Sync Output
14
15
IN
REMOTE
OUT ROTA
40
41
V-H-SW(NU) Not Used
17
-
NU
Not Used
Video Head Switching
Pulse
OUT XC-OUT
-
Vcc
X-IN
Main Clock Input
GND
OUT SPOT-KILL
-
43
IN
Sub Clock 32 kHz
TIMER+5V
OUT X-OUT
42
44
Color Phase Rotary
Changeover SIgnal
-
OUT RF-SW
39
Remote Signal Input
16
18
36
Main Clock Output
GND
Counter-measure for Spot
NU
Not Used
CLKSEL
Clock Select (GND)
OUT D-REC-H
Delayed Record Signal
I2C-OPEN
White Balance Adjust
Mode Judgment
-
GND
GND
47
-
NU
Not Used
48
-
NU
Not Used
49
-
GND
OSD GND
50
-
GND
GND
51
-
NU
Not Used
52
-
NU
Not Used
45
IN
46
19
-
NU
Not Used
53
-
P-ON+5V
OSD Vcc
20
-
NU
Not Used
54
-
HLF
HLF
21
-
IF-MUTE
IF-MUTE Signal
55
IN
V-HOLD
VHOLD
OUT REC-LED
Recording LED Control
Signal
56
IN
CV-IN
Video Signal Input
57
-
GND
GND
OUT REC-LED
Recording LED Control
Signal
58
IN
H-SYNC
H-SYNC Input
59
IN
V-SYNC
V-SYNC Input
22
23
24
-
NU
Not Used
25
-
NU
Not Used
26
-
FM/TV-SW
FM/TV-SW Signal
27
-
NU
Not Used
28
-
NU
Not Used
29
-
NU
Not Used
30
-
NU
Not Used
31
OUT P-ON-H
60
61
Power On Signal at High
1-12-1
OUT OSD-BLK
-
NU
Output for Picture Cut off
Not Used
62
OUT OSD-B
Blue Output
63
OUT OSD-G
Green Output
64
OUT OSD-R
Red Output
65
OUT A-MUTE
Audio Mute Output
66
OUT C-F/R
Capstan Motor FWD/REV
Control Signal
T5553PIN
Pin IN/
No. OUT
Signal
Name
67
-
NU
68
-
YCA-SOUT YCA-SOUT Signal
69
-
YCA-CS
YCA-CS Signal
70
-
YCA-SCLK
YCA-SCLK Signal
Not Used
71
OUT SCL
E2PROM/CHROMA IC
Tuner Communication
Clock
72
IN/
SDA
OUT
E2PROM/CHROMA IC
Tuner Communication Data
73
-
74
IN
75
-
NU
Not Used
C-SYNC
C-Sync Input
NU
Not Used
76
OUT C-CONT
Capstan Motor Control
Signal
77
OUT D-CONT
Drum Motor Control Signal
78
-
NU
Not Used
79
-
NU
Not Used
80
IN
T-REEL
Take Up Reel Rotation
Signal
81
-
NU
Not Used
82
OUT LD-CONT
83
-
84
IN
85
Not Used
P-DOWN
Power Voltage Down
Detector Signal
-
NU
Not Used
86
-
GND
GND
87
IN
C-FG
Capstan Motor Rotation
Detection Pulse
88
-
GND
GND (AMP)
89
-
NU
Not Used
90
IN
D-PFG
Drum Motor Pulse
Generator
91
-
NU
Not Used
92
OUT
AMP VREF
IN
Standard Voltage Input
93
-
C
C
94
IN/
CTL (-)
OUT
CTL (-)
95
IN/
CTL (+)
OUT
CTL (+)
-
AMPC
Signal
Name
Function
97
OUT
CTL AMP
OUT
Control Amp Output
98
-
P-ON+5V
Power Supply for AMP
99
-
AL+5V
A/D, D/A Standard Voltage
100
-
NU
Not Used
Loading Motor Control
Signal
NU
96
Pin IN/
No. OUT
Function
AMPC
1-12-2
T5553PIN
LEAD IDENTIFICATIONS
2SC5884000RF
TT2138LS-YB11
2SK3563
MID-32A22F
PT204-6B-12
E: Emitter
C: Collector
B: Base
S: Souce
D: Drain
G: Gate
C
B C E
S D G
E
2SC1815-GR(TPE2)
2SC2120-(O,Y)(TPE2)
2SC3331(T,U)
KRA103M
KTC3203(Y)
LA78040A
ECB
ECB
IN G OUT
LTV-817B-F
LTV-817C-F
PC817X6
A
KA7805A
KIA7805API
2SA1015-GR(TPE2)
2SA1175(F)
2SA950(O,Y)
2SC1627Y-TPE2
2SC2482 TPE6
2SC2785(F)
2SC3468(D,E)-AE
BN1F4M-T
KTA1267(GR)
KTA1271(Y)
KTC3199(GR)
KTC3207
C
K
M37762M8A-8D4GP
80
E
AN17811A
8
5
1
4
51
81
50
100
31
1
30
IN G OUT
M61113FP
20
BR24C02F-W
CAT24WC02JI
M24C02-WMN6
8
60
1
4
41
10
61
40
80
21
M61275FP-61
5
42
1
LA71205M-MPB-E
11
1
22
21
1-13-1
1
20
T5553LE
EXPLODED VIEWS
Cabinet
SHINWHA
TAPE SGT-730
(BLACK)
V501-2
Details for L551
and surrounding parts
SHINWHA
TAPE SGT-730
(WHITE)
V501-1
L551
L1
V501-3
TL3
B2
TB24
CRT CBA
CLN551
A3
L1
B3
TB2
TL3
L551
TB24
L7
TL1
TL1
B2
B2
DG601
TL1
B1
SCOTCH
TAPE #880
L1
1B1
L1
TL2
TB9
W601
TL1
B2
V501
TB3
TB26
SENSOR CBA
TB8
L4
TL1
A1X
A2
TL2
TL2
TL1
TB10
TL1
TB21
SP801
A1-5
TB11
A1-1
MAIN CBA
CL802
TB7
TL4
A1-4
TL5
SENSOR CBA
L2
A1-3
B13
TB1
See Electrical Parts List
for parts with this mark.
A1-2
1-14-1
1-14-2
T5553CEX
Packing
X2
X3
X7
X4
S2
X1
TAPE
X5
S6
S3
S1
S4
S15
FR
ON
T
1-14-3
T5553PEX
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a #
have special characteristics important to safety. Before
replacing any of these components, read carefully the
product safety notice in this service manual. Don't
degrade the safety of the product through improper servicing.
Ref. No.
X4
X5
NOTE:
Parts that are not assigned part numbers (---------) are
not available.
Ref. No.
A1X
Description
FRONT CABINET ASSEMBLY T5553UD
Part No.
0EM101449
X7
Description
DRY BATTERY R6P UM3 or
Part No.
XB0M451GH001
DRY BATTERY R6P(AR)2PX or
XB0M451HU002
DRY BATTERY R6P(AR)2P X ICI or
XB0M451HU003
DRY BATTERY(SUNRISE) R6SSE/2S or
XB0M451MS002
DRY BATTERY R6P/2S
XB0M451T0001
ROD ANTENNA T5200UA or
0EMN01755
ROD ANTENNA L7720UA:NTSC W/COO or
0EMN00673
ROD ANTENNA T5000UA
0EMN01599
SHEET RETURN STOP T4259UK
0EM406203A
Note:
1. V501 (CRT) HAS COUPLE OF SUBSTITUTIONAL PARTS AND EACH PARTS
ALSO HAS MATCHING COMBINATION WITH L551.
PLEASE SEE TABLE 1 FOR DETAILS OF MATCHING COMBINATION.
2. L551 (DEFLECTION YOKE) HAS MATCHING COMBINATION WITH V501.
PLEASE SEE TABLE 1 FOR DETAILS OF MATCHING COMBINATION.
CRT TYPE A
A2
REAR CABINET T5553UD
0EM101452
A3#
RATING LABEL T5553UD
----------
L551#
DEFLECTION YOKE LLBY00ZSY005 or
LLBY00ZSY005
A1-1
FRONT CABINET T5553UD
0EM101453
#
DEFLECTION YOKE KDY3GDA82X
LLBY00ZMS011
A1-2
CONTROL PLATE T5553UD
0EM201826
V501#
CRT A34AGT13X
TCRT190CP036
C.P.MAGNET JH225-FN-00
XM04000BV003
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
A1-3
BRAND PLATE T5303UDEMERSON
0EM406919
V501-1
A1-4
CASSETTE DOOR T5553UD
0EM302054
V501-2
A1-5
SPRING DOOR(Z10) T5200UA
0EM406687
1B1
DECK ASSEMBLY CZD013/VM2226
N2226FT
V501-3
RUBBER MAGNET 20X10X1.2
XM05000BV001
CRT TYPE B
B1
SPRING TENSION B0080B0:EM40808
B2
M5 CRT SCREW(B) B4000UA
26WH006
0VM403923
L551#
DEFLECTION YOKE LLBY00ZSY002 or
LLBY00ZSY002
B3
SHIELD PLATE T5500UA
0EM408707
#
DEFLECTION YOKE KDY3GCE83X
LLBY00ZMS027
B13
CLOTH(15X10XT0.5) L9700UA
0EM405038
V501#
CRT A34JQQ093X
TCRT190MS010
C.P.MAGNET JH225-FN-00
XM04000BV003
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
CL802
WIRE ASSEMBLY 2P/150
WX1B5900-001
V501-1
CLN551
CRT GND WIRE CRT GND
WX1L7720-001
V501-2
DG601#
DEGAUSSING COIL F-019 or
LLBH00ZTM019
#
DEGAUSSING COIL AVDG016
LLBH00ZWR016
V501-3
RUBBER MAGNET 20X10X1.2
XM05000BV001
CRT TYPE C
L1
SCREW, P-TIGHT 4X18 BIND HEAD +
GBMP4180
L2
SCREW TAPPING M4X14
DBU14140
L551#
DEFLECTION YOKE KDY3GCE83X or
L4
SCREW, P-TIGHT 3X10 BIND HEAD
GBUP3100
#
DEFLECTION YOKE LLBY00ZSY002 or
LLBY00ZSY002
L7
SCREW, P-TIGHT 3X10 BIND HEAD+
GBKP3100
#
DEFLECTION YOKE CDY-M1456S or
LLBY00ZQS008
SP801
SPEAKER S08F02B or
DSD0808XQ010
#
DEFLECTION YOKE DSE1493FU(S)
LLBY00ZSM008
SPEAKER J-F097-C5
DSD0808DCP01
V501#
CRT A34KQW42X
TCRT190SM013
XM04000BV003
LLBY00ZMS027
TB1
TRAY CHASSIS T5400UA
0EM000688
V501-1
C.P.MAGNET JH225-FN-00
TB2
TOP SHIELD T5500UA
0EM201787
V501-2
WEDGE FT-00110W or
XV10000T4001
TB8
SPEAKER HOLDER T5100UA
0EM201157B
WEDGE DB25SR
XV10000D9001
TB10
RCA HOLDER T5400UA
0EM407677
TB11
CLOTH(10X30XT:0.3) T5300UA
0EM407441
V501-3
RUBBER MAGNET 20X10X1.2
XM05000BV001
CRT TYPE D
TB24
WIRE HOLDER T5400UA
0EM407678
L551#
DEFLECTION YOKE CDY-M1422F
LLBY00ZQS001
TL1
SCREW, P-TIGHT 3X12 WASHER HEAD+
GCMP3120
V501#
CRT A34JLL90X(W)
TCRT190QS015
TL3
SCREW, S-TIGHT 3X4 BIND HEAD+
GBMS3040
V501-1
C.P.MAGNET JH225-FN-00
XM04000BV003
TL4
SCREW, B-TIGHT M3X8 BIND HEAD+
GBMB3080
V501-2
WEDGE FT-00110W or
XV10000T4001
TL5
SCREW, P-TIGHT M3X8 BIND HEAD+
GBCP3080
WEDGE DB25SR
XV10000D9001
S1
CARTON T5553UD
S2
STYROFOAM TOP T5553UD
0EM000892
L551#
DEFLECTION YOKE CDY-M1455F or
LLBY00ZQS007
S3
STYROFOAM BOTTOM T5553UD
0EM000893
#
DEFLECTION YOKE LLBY00ZSY003 or
LLBY00ZSY003
S4
SERIAL NO. LABEL L9750UA
----------
#
DEFLECTION YOKE KDY3GD592X
LLBY00ZMS004
S6
SET SHEET B5506UG:800X1500
0EM402369
V501#
CRT A34LRQ90X(VW)
TCRT190P7003
S15
LABEL, EAS(H3761UD) MAKER NO.ZLLFNSLE1
----------
V501-1
C.P.MAGNET JH225-FN-00
XM04000BV003
V501-2
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
V501-3
PACKING
ACCESSORIES
X1
BAG POLYETHYLENE 235X365XT0.03
0EM408420
X2#
OWNERS MANUAL T5553UD
0EMN02375
X3
REMOTE CONTROL 512/ERC001/N0162UD or
N0162UD
REMOTE CONTROL 512/ERC001/N0159UD
N0159UD
20040106
RUBBER MAGNET 20X10X1.2
XM05000BV001
CRT TYPE E
0EM408945
V501-3
RUBBER MAGNET 20X10X1.2
XM05000BV001
CRT TYPE F
L551#
1-15-1
DEFLECTION YOKE LLBY00ZSY002 or
LLBY00ZSY002
T5553CA
Ref. No.
Description
Part No.
#
DEFLECTION YOKE KDY3GCE83X or
LLBY00ZMS027
#
DEFLECTION YOKE CDY-M1456S
LLBY00ZQS008
V501#
CRT A34KPU02XX
TCRT190GS016
V501-1
C.P.MAGNET JH225-FN-00
XM04000BV003
V501-2
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
V501-3
RUBBER MAGNET 20X10X1.2
XM05000BV001
CRT TYPE G
L551#
DEFLECTION YOKE LLBY00ZSY002 or
#
DEFLECTION YOKE KDY3GCE83X or
LLBY00ZMS027
#
DEFLECTION YOKE CDY-M1456S
LLBY00ZQS008
V501#
CRT A34JXV70X
TCRT190THA02
V501-1
C.P.MAGNET JH225-FN-00
XM04000BV003
V501-2
WEDGE FT-00110W or
XV10000T4001
WEDGE DB25SR
XV10000D9001
RUBBER MAGNET 20X10X1.2
XM05000BV001
V501-3
LLBY00ZSY002
Table 1 (V501 and L551 Combination)
Note 1: Purity and Convergence Adjustments must be
performed following CRT replacement. Refer to Electrical Adjustment Instructions.
Note 2: Please confirm CRT Type No. on the CRT
Warning Label which is located on the CRT. Then See
the Table 1 for V501 and L551 combination chart.
Please refer this CRT, Deflection Yoke combination
chart for parts order.
V501: CRT Type No.
V501: CRT Part No.
A34AGT13X
TCRT190CP036
A34JQQ093X
TCRT190MS010
L551: Deflection
Yoke Part No.
LLBY00ZSY005
LLBY00ZMS011
LLBY00ZSY002
LLBY00ZMS027
LLBY00ZMS027
A34KQW42X
TCRT190SM013
A34JLL90X(W)
TCRT190QS015
A34LRQ90X(VW)
TCRT190P7003
LLBY00ZSY002
LLBY00ZQS008
LLBY00ZSM008
LLBY00ZQS001
LLBY00ZQS007
LLBY00ZSY003
LLBY00ZMS004
LLBY00ZSY002
A34KPU02XX
TCRT190GS016
LLBY00ZMS027
LLBY00ZQS008
LLBY00ZSY002
A34JXV70X
TCRT190THA02
LLBY00ZMS027
LLBY00ZQS008
CRT Warning Label Location
CRT Type No.
CRT Warning Label
CRT
20040106
1-15-2
T5553CA
ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read carefully the product safety notice in this service manual.
Don't degrade the safety of the product through
improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
MMA CBA
Ref. No.
Description
MMA CBA
Part No.
0ESA05886
Consists of the following
MAIN CBA
Ref. No.
Description
MAIN CBA
Consists of the following
C210
CHIP CERAMIC CAP. F Z 0.47µF/10V
CHD1AZB0F474
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
C212
CHIP CERAMIC CAP. CH J 22pF/50V
CHD1JJBCH220
C213
CHIP CERAMIC CAP. CH J 22pF/50V
CHD1JJBCH220
C214
ELECTROLYTIC CAP.(SS.T) 220µF/10V M H7
CA1A221S6028
C216
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
C217
CHIP CERAMIC CAP.(MELF) SL D 10pF/50V
CZM1JDBSL100
C218
CHIP CERAMIC CAP. CH J 15pF/50V
CHD1JJBCH150
C219
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C220
ELECTROLYTIC CAP. 220µF/6.3V M H7
CE0KMAVSL221
C221
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
C222
CHIP CERAMIC CAP.(MELF) Y K 2200pF/35V
CZM1GKB0Y222
C223
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C224
CHIP CERAMIC CAP.(MELF) Y K 1000pF/35V
CZM1GKB0Y102
C225
CHIP CERAMIC CAP. CH J 560pF/50V
CHD1JJBCH561
C231
CHIP CERAMIC CAP. CH J 100pF/50V
CHD1JJBCH101
C232
CHIP CERAMIC CAP. CH J 100pF/50V
CHD1JJBCH101
C233
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
C235
CHIP CERAMIC CAP. B K 4700pF/50V
CHD1JKB0B472
C236
CERAMIC CAP.(AX) F Z 0.047µF/16V
CCA1CZTFZ473
C238
CHIP CERAMIC CAP.(MELF) Y K 1000pF/35V
CZM1GKB0Y102
ELECTROLYTIC CAP. 22µF/50V M or
CE1JMASDL220
ELECTROLYTIC CAP. 22µF/50V M
CE1JMASTL220
C240
CERAMIC CAP.(AX) B J 560pF/50V
CCA1JJT0B561
C241
CHIP CERAMIC CAP. B K 4700pF/50V
CHD1JKB0B472
C242
CHIP CERAMIC CAP. CH J 100pF/50V
CHD1JJBCH101
-----------C245
CAPACITORS
C002
CHIP CERAMIC CAP. CH J 100pF/50V
CHD1JJBCH101
C003
CHIP CERAMIC CAP. CH J 100pF/50V
CHD1JJBCH101
Part No.
CE0KMAVSL470
C211
C243
Part No.
Description
ELECTROLYTIC CAP. 47µF/6.3V M H7
C239
----------------------0ESA04524
MAIN CBA
CRT CBA
SENSOR CBA
Ref. No.
C208
C247
ELECTROLYTIC CAP. 22µF/16V M LL or
CE1CMASLL220
ELECTROLYTIC CAP. 22µF/16V M LL
CE1CMASLH220
ELECTROLYTIC CAP. 220µF/16V M or
CE1CMASDL221
ELECTROLYTIC CAP. 220µF/16V M
CE1CMASTL221
ELECTROLYTIC CAP. 220µF/16V M or
CE1CMASDL221
ELECTROLYTIC CAP. 220µF/16V M
CE1CMASTL221
CCA1JZTFZ104
ELECTROLYTIC CAP. 220µF/6.3V M or
CE0KMASDL221
C250
CERAMIC CAP.(AX) F Z 0.1µF/50V
ELECTROLYTIC CAP. 220µF/6.3V M
CE0KMASTL221
C252
ELECTROLYTIC CAP.(SS.T) 100µF/16V M H7
CA1C101S6028
C007
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C253
ELECTROLYTIC CAP. 100µF/6.3V M or
CE0KMASDL101
C008
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMAVSL100
ELECTROLYTIC CAP. 100µF/6.3V M
CE0KMASTL101
C032
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
ELECTROLYTIC CAP. 47µF/35V M or
CE1GMASDL470
C033
ELECTROLYTIC CAP. 470µF/10V M or
CE1AMASDL471
ELECTROLYTIC CAP. 470µF/10V M
CE1AMASTL471
C036
CHIP CERAMIC CAP. B K 1000pF/50V
C037
CHIP CERAMIC CAP. F Z 1µF/10V
C039
C005
C254
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASTL470
C257
CHIP CERAMIC CAP.(MELF) Y K 1000pF/35V
CZM1GKB0Y102
CHD1JKB0B102
C265
CHIP CERAMIC CAP. CH J 100pF/50V
CHD1JJBCH101
CHD1AZB0F105
C266
CHIP CERAMIC CAP. CH J 100pF/50V
CHD1JJBCH101
ELECTROLYTIC CAP. 0.1µF/50V M H7
CE1JMAVSLR10
C267
CERAMIC CAP.(AX) CH J 100pF/50V
CA1J101TU008
C042
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C301
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
C043
CHIP CERAMIC CAP. F Z 0.022µF/50V
CHD1JZB0F223
C302
CHIP CERAMIC CAP. CH J 33pF/50V
CHD1JJBCH330
C044
CERAMIC CAP.(AX) Y M 0.01µF/16V
CCA1CMT0Y103
C303
CHIP CERAMIC CAP. CH J 33pF/50V
CHD1JJBCH330
C046
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
C304
CHIP CERAMIC CAP. CH J 33pF/50V
CHD1JJBCH330
C047
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C309
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C048
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASDL100
C310
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASTL100
C314
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C315
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C049
C052
CHIP CERAMIC CAP. F Z 0.047µF/50V
CHD1JZB0F473
C316
CHIP CERAMIC CAP. F Z 2.2µF/10V
CHD1AZB0F225
C053
FILM CAP.(P) 0.018µF/50V J
CA1J183MS029
C317
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
C054
CERAMIC CAP.(AX) Y M 0.01µF/16V
CCA1CMT0Y103
C319
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C203
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C320
CHIP CERAMIC CAP. F Z 0.47µF/10V
CHD1AZB0F474
C206
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C321
ELECTROLYTIC CAP. 220µF/6.3V M H7
CE0KMAVSL221
C207
ELECTROLYTIC CAP.(SS.T) 47µF/25V M H7
CA1E470S6028
C322
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
20040106
1-16-1
T5553EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
C323
CHIP CERAMIC CAP. F Z 2.2µF/10V
CHD1AZB0F225
C572#
P.P. CAP 0.33µF/200V J or
CA2D334VC012
C324
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
#
PP CAP. 0.33µF/250V J
CT2E334MS041
C325
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C574#
ELECTROLYTIC CAP. 4.7µF/250V M or
CE2EMASDL4R7
C326
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
#
ELECTROLYTIC CAP. 4.7µF/250V M
CE2EMASTL4R7
C327
ELECTROLYTIC CAP. 100µF/10V M H7
CE1AMAVSL101
C577
FILM CAP.(P) 0.022µF/50V J or
CMA1JJS00223
C330
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
FILM CAP.(P) 0.022µF/50V J
CA1J223MS029
C331
ELECTROLYTIC CAP.(SS.T) 220µF/10V M H7
CA1A221S6028
ELECTROLYTIC CAP. 47µF/35V M or
CE1GMASDL470
C336
ELECTROLYTIC CAP. 1µF/50V H7(P=2.5MM)
CA1J1R0S6023
C337
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C578
C580#
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASTL470
P.P. CAP 0.0082µF/1.6K J or
CA3C822VC011
C338
CHIP CERAMIC CAP. F Z 2.2µF/10V
CHD1AZB0F225
#
PP CAP. 0.0082µF/1.6KV J or
CT3C822MS039
C339
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
#
METALLIZED FILM CAP. 0.0082µF/1.6KV J or
CT3C822F7004
C340
CHIP CERAMIC CAP. CH J 47pF/50V
CHD1JJBCH470
#
POLYPROPYLENE FILM CAP. 0.0082µF/1.6KV
CT3C822HJE16
C342
ELECTROLYTIC CAP.(SS.T) 220µF/10V M H7
CA1A221S6028
C584#
ELECTROLYTIC CAP. 1µF/160V M or
CE2CMASDL1R0
C351
ELECTROLYTIC CAP.(SS.T) 220µF/10V M H7
CA1A221S6028
#
ELECTROLYTIC CAP. 1µF/160V M
CE2CMASTL010
C352
ELECTROLYTIC CAP.(SS.T) 220µF/10V M H7
CA1A221S6028
C591
ELECTROLYTIC CAP. 2.2µF/50V M H7
CE1JMAVSL2R2
C410
ELECTROLYTIC CAP. 1µF/50V M H7
CE1JMAVSL1R0
C592
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C411
ELECTROLYTIC CAP. 100µF/10V M H7
CE1AMAVSL101
C593
ELECTROLYTIC CAP. 2.2µF/50V M or
CE1JMASDL2R2
C412
CHIP CERAMIC CAP.(MELF) F Z 0.01µF/16V
CZM1CZB0F103
ELECTROLYTIC CAP. 2.2µF/50V M
CE1JMASTL2R2
C413
CHIP CERAMIC CAP. CH J 390pF/50V
CHD1JJBCH391
C416
CHIP CERAMIC CAP.(MELF) SL J 100pF/50V
CZM1JJBSL101
C417
CHIP CERAMIC CAP.(MELF) SL J 100pF/50V
CZM1JJBSL101
C418
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
C419
ELECTROLYTIC CAP. 1µF/50V M H7
C420
C594
ELECTROLYTIC CAP. 10µF/160V M or
CE2CMZPDL100
ELECTROLYTIC CAP. 10µF/160V M
CE2CMZNTL100
C602#
SAFETY CAP. 4700pF/250V KX
CA2E472MR050
C605#
METALLIZED FILM CAP. 0.1µF/250V or
CT2E104MS037
CE1JMAVSL1R0
#
FILM CAP.(MP) 0.1µF/250V K or
CT2E104DC011
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
#
METALLIZED FILM CAP. 0.1µF/275V K or
CT2E104HJE06
C421
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
#
LINE ACROSS CAP. 0.1U/250V
CT2E104DC015
C422
ELECTROLYTIC CAP. 1µF/50V M H7
CE1JMAVSL1R0
C606
CERAMIC CAP. F Z 0.01µF/500V or
CCD2JZP0F103
C423
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
CERAMIC CAP. 0.01µF/AC250V or
CCD2EZA0F103
C424
ELECTROLYTIC CAP. 0.1µF/50V M H7
CE1JMAVSLR10
CERAMIC CAP. E Z 0.01µF/500V
CCD2JZP0E103
C425
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
CERAMIC CAP. F Z 0.01µF/500V or
CCD2JZP0F103
C607
C426
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
CERAMIC CAP. 0.01µF/AC250V or
CCD2EZA0F103
C427
CERAMIC CAP.(AX) B K 0.01µF/50V
CA1J103TU011
CERAMIC CAP. E Z 0.01µF/500V
CCD2JZP0E103
C428
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C610#
ELECTROLYTIC CAPACIT0R 150µF/200V or
CA2D151S6012
C429
ELECTROLYTIC CAP. 47µF/6.3V M H7
CE0KMAVSL470
#
ALMINIUM ELECTROLYTIC CAP150µF/200V
CA2D151NC088
C430
CHIP CERAMIC CAP. B K 0.022µF/50V
CHD1JKB0B223
C611
CERAMIC CAP. BN 680pF/2KV or
CCD3DKA0B681
C431
ELECTROLYTIC CAP. 1µF/50V M H7
CE1JMAVSL1R0
CERAMIC CAP. 680pF/2KV or
CA3D681PAN04
C432
ELECTROLYTIC CAP. 1µF/50V M H7
CE1JMAVSL1R0
CERAMIC CAP. RB 680pF/2KV
CA3D681TE006
C435
ELECTROLYTIC CAP. 1µF/50V M H7
CE1JMAVSL1R0
C436
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C612
C438
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZB0F105
C439
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C441
CHIP CERAMIC CAP. F Z 0.047µF/50V
CHD1JZB0F473
C614#
FILM CAP.(P) 0.056µF/50V J or
CMA1JJS00563
C442
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
#
FILM CAP.(P) 0.056µF/50V J
CA1J563MS029
C443
CHIP CERAMIC CAP. F Z 0.047µF/50V
CHD1JZB0F473
C615
CERAMIC CAP. BN 560pF/2KV or
CCD3DKA0B561
C444
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
CERAMIC CAP. 560pF/2KV or
CA3D561PAN04
C445
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
CERAMIC CAP. RB 560pF/2KV
CA3D561TE006
CE2CMZPDL101
C613
FILM CAP.(P) 0.039µF/50V J or
CMA1JJS00393
FILM CAP.(P) 0.039µF/50V J
CA1J393MS029
FILM CAP.(P) 0.001µF/50V J or
CMA1JJS00102
FILM CAP.(P) 0.001µF/50V J
CA1J102MS029
C447
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C616#
ELECTROLYTIC CAP. 100µF/160V M or
C449
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
#
ELECTROLYTIC CAP. 100µF/160V M or
CE2CMZPTL101
C552
MYLAR CAP. 0.22µF/50V J or
CMA1JJS00224
#
ELECTROLYTIC CAP. 100µF/160V M W/F
CE2CMZNTL101
FILM CAP.(P) 0.22µF/50V J or
CA1J224MS029
C617#
ELECTROLYTIC CAP. 470µF/35V M or
CE1GMASDL471
TF CAP. 0.22µF/50V J
CT1J224MS045
#
ELECTROLYTIC CAP. 470µF/35V M
CE1GMASTL471
ELECTROLYTIC CAP. 1µF/50V LL or
CE1JMASLH1R0
C618#
ELECTROLYTIC CAP. 1000µF/16V M or
CE1CMZPDL102
ELECTROLYTIC CAP. 1µF/50V M LL or
CE1JMASLL1R0
#
ELECTROLYTIC CAP. 1000µF/16V M
CE1CMZPTL102
ELECTROLYTIC CAP. 1µF/50V M LL
CE1JMASLL010
C619
ELECTROLYTIC CAP. 47µF/35V M or
CE1GMASDL470
C553
C555
C556
ELECTROLYTIC CAP. 470µF/16V M or
CE1CMASDL471
ELECTROLYTIC CAP. 470µF/16V M
CE1CMASTL471
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASTL470
C620#
ELECTROLYTIC CAP. 1000µF/16V M or
CE1CMZPDL102
ELECTROLYTIC CAP. 1000µF/25V M or
CE1EMZPDL102
#
ELECTROLYTIC CAP. 1000µF/16V M
CE1CMZPTL102
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZPTL102
C622
CERAMIC CAP.(AX) CH J 100pF/50V
CA1J101TU008
C558
CERAMIC CAP.(AX) B K 0.01µF/50V
CA1J103TU011
C623
FILM CAP.(P) 0.01µF/50V J or
CMA1JJS00103
C559
ELECTROLYTIC CAP. 330µF/35V M or
CE1GMASDL331
FILM CAP.(P) 0.01µF/50V J
CA1J103MS029
ELECTROLYTIC CAP. 330µF/35V M
CE1GMASTL331
C624
CERAMIC CAP.(AX) B K 0.01µF/50V
CA1J103TU011
FILM CAP.(P) 0.01µF/100V J
CMA2AJS00103
C625
ELECTROLYTIC CAP. 3.3µF/50V M or
CE1JMASDL3R3
C560
20040106
1-16-2
T5553EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
ELECTROLYTIC CAP. 3.3µF/50V M
CE1JMASTL3R3
C626
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C627
ELECTROLYTIC CAP. 47µF/35V M or
CE1GMASDL470
LED LAMP 333HT/F45-50K or
NPWK333HTF45
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASTL470
LED LAMP 333HT/F45-50L or
NPWL333HTF45
C628
C629
C630
C631
C632
C633
C634
C635
ELECTROLYTIC CAP. 10µF/50V M or
CE1JMASDL100
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASTL100
D204
ELECTROLYTIC CAP. 47µF/35V M or
CE1GMASDL470
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASTL470
ELECTROLYTIC CAP. 100µF/10V M or
CE1AMASDL101
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASTL101
NPWM333HTF45
ZENER DIODE MTZJT-776.2B or
QDTB0MTZJ6R2
ZENER DIODE DZ-6.2BSBT265
NDTB0DZ6R2BS
D225
ZENER DIODE MTZJT-776.2B or
QDTB0MTZJ6R2
ZENER DIODE DZ-6.2BSBT265
NDTB0DZ6R2BS
D226
ZENER DIODE MTZJT-776.2B or
QDTB0MTZJ6R2
ZENER DIODE DZ-6.2BSBT265
NDTB0DZ6R2BS
D227
PCB JUMPER D0.6-P5.0
JW5.0T
ELECTROLYTIC CAP. 100µF/16V M or
CE1CMASDL101
D231
ZENER DIODE MTZJT-775.6B or
QDTB0MTZJ5R6
ELECTROLYTIC CAP. 100µF/16V M
CE1CMASTL101
ELECTROLYTIC CAP. 47µF/35V M or
CE1GMASDL470
ELECTROLYTIC CAP. 47µF/35V M
CE1GMASTL470
ELECTROLYTIC CAP. 100µF/16V M or
CE1CMASDL101
ELECTROLYTIC CAP. 100µF/16V M
CE1CMASTL101
ELECTROLYTIC CAP. 47µF/16V M H7
CE1CMAVSL470
CHD1JZB0F104
CCD2JKS0B222
C648
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C650
ELECTROLYTIC CAP. 47µF/25V M or
CE1EMASDL470
ELECTROLYTIC CAP. 47µF/25V M
CE1EMASTL470
ELECTROLYTIC CAP. 220µF/16V M or
CE1CMASDL221
ELECTROLYTIC CAP. 220µF/16V M
CE1CMASTL221
ELECTROLYTIC CAP. 470µF/16V M or
CE1CMASDL471
ELECTROLYTIC CAP. 470µF/16V M
CE1CMASTL471
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C804
ELECTROLYTIC CAP. 0.22µF/50V M H7
CE1JMAVSLR22
C805
CHIP CERAMIC CAP. B K 4700pF/50V
CHD1JKB0B472
C852
ELECTROLYTIC CAP. 33µF/16V M H7
CE1CMAVSL330
C853
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
C854
ELECTROLYTIC CAP. 22µF/16V M H7
CE1CMAVSL220
C856
CHIP CERAMIC CAP. F Z 0.1µF/50V
CHD1JZB0F104
C858
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C861
CHIP CERAMIC CAP. CH J 820pF/50V
CHD1JJBCH821
C862
CHIP CERAMIC CAP. B K 0.015µF/50V
CHD1JKB0B153
C863
ELECTROLYTIC CAP. 4.7µF/50V M H7
CE1JMAVSL4R7
C865
CHIP CERAMIC CAP. B K 0.01µF/50V
CHD1JKB0B103
C866
CHIP CERAMIC CAP. B K 2700pF/50V
CHD1JKB0B272
C867
CHIP CERAMIC CAP. B K 1000pF/50V
CHD1JKB0B102
C872
ELECTROLYTIC CAP. 220µF/6.3V M H7
CE0KMAVSL221
C873
ELECTROLYTIC CAP.(SS.T) 100µF/16V M H7
CA1C101S6028
C875
LED LAMP 333HT/F45-50M
D208
CE0KMASDL221
CHIP CERAMIC CAP. F Z 0.1µF/50V
C874
D251
D254
ZENER DIODE DZ-5.6BSBT265
NDTB0DZ5R6BS
ZENER DIODE MTZJT-7715B or
QDTB00MTZJ15
ZENER DIODE DZ-15BSBT265
NDTB00DZ15BS
ZENER DIODE MTZJT-7718A or
QDTA00MTZJ18
ZENER DIODE DZ-18BSAT265
NDTA00DZ18BS
D302
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D303
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D304
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D305
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D306
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D309
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D311
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D312
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D313
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D314
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D315
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D401
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D552
DIODE 1N5397-B or
NDLZ001N5397
RECTIFIER DIODE ERB12-06
QDQZ0ERB1206
CERAMIC CAP. B K 470pF/100V or
CCD2AKS0B471
D571#
DIODE FR154 or
NDLZ000FR154
CERAMIC CAP. B K 470pF/500V
CCD2JKS0B471
#
FAST RECOVERY DIODE ERB44-02
QDPZ0ERB4402
FILM CAP.(P) 0.018µF/100V J or
CMA2AJS00183
D572#
DIODE FR104-B
NDLZ000FR104
FILM CAP.(P) 0.018µF/50V J
CA1J183MS029
D584
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
CONNECTOR BASE, 5P TV-50P-05-V3 or
J3TVC05TG002
D585
ZENER DIODE MTZJT-775.1B or
QDTB0MTZJ5R1
CONNECTORS
CN571
NPQZLTL4214M
CE0KMASTL221
CERAMIC CAP. B K 2200pF/500V
C803
LED LTL-4214M1 or
ELECTROLYTIC CAP. 220µF/6.3V M
C636
C802
NPZZM1E534A2
ELECTROLYTIC CAP. 220µF/6.3V M or
C639
C801
LED MIE-534A2
ZENER DIODE DZ-5.1BSBT265
NDTB0DZ5R1BS
ZENER DIODE MTZJT-7736B or
QDTB00MTZJ36
#
ZENER DIODE DZ-36BSBT265
NDTB00DZ36BS
D595
ZENER DIODE MTZJT-7718B or
QDTB00MTZJ18
ZENER DIODE DZ-18BSBT265
NDTB00DZ18BS
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
CONNECTOR BASE, 5P RTB-1.5-5P
J3RTC05JG001
CN601
CONNECTOR BASE, 2P TV-50P-02-V3 or
J3TVC02TG002
D591#
CONNECTOR BASE, 2P RTB-1.5-2P
J3RTC02JG001
CN801
STRAIGHT CONNECTOR BASE 00 8283 0212 00 J383C02UG002
000 or
STRAIGHT PIN HEADER, 2P 173981-2
D596
1770258
DIODES
SWITCHING DIODE 1N4148
NDTZ001N4148
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D031
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D203
LED SIR-563ST3F P or
QPQPS1R563ST
D598#
DIODE FR104-B
NDLZ000FR104
LED SIR-563ST3F Q or
QPQQS1R563ST
D603
DIODE 1N5397-B or
NDLZ001N5397
20040106
D597
1-16-3
T5553EL
Ref. No.
D604
D605
D606
Description
Part No.
Ref. No.
#
ZENER DIODE DZ-36BSAT265
NDTA00DZ36BS
DIODE 1N5397-B or
NDLZ001N5397
D643
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
RECTIFIER DIODE ERB12-06
QDQZ0ERB1206
DIODE 1N5397-B or
NDLZ001N5397
RECTIFIER DIODE ERB12-06
QDQZ0ERB1206
DIODE 1N5397-B or
NDLZ001N5397
RECTIFIER DIODE ERB12-06
QDQZ0ERB1206
ZENER DIODE MTZJT-7720C or
QDTC00MTZJ20
#
ZENER DIODE DZ-20BSCT265
NDTC00DZ20BS
D609
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D611
Part No.
QDQZ0ERB1206
D607#
D610
Description
RECTIFIER DIODE ERB12-06
SWITCHING DIODE 1N4148
NDTZ001N4148
ZENER DIODE MTZJT-775.6B or
QDTB0MTZJ5R6
ZENER DIODE DZ-5.6BSBT265
NDTB0DZ5R6BS
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D646
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D801
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D802
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D803
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D964
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
D965
ZENER DIODE MTZJT-776.2B or
QDTB0MTZJ6R2
ZENER DIODE DZ-6.2BSBT265
NDTB0DZ6R2BS
SWITCHING DIODE 1N4148
NDTZ001N4148
D613#
RECTIFIER DIODE 15DF4 or
QDQZ00015DF4
#
RECOVERY DIODE ERC18-04
QDZZ0ERC1804
IC001
IC:VIF/SIF M61113FP
D614#
DIODE FR104-B
NDLZ000FR104
IC201#
MICRO COMPUTER M37762M8A-8D4GP
QSZAA0RHT013
D615#
DIODE 1ZC33 or
QDQZ0001ZC33
IC202
IC:MEMORY BR24C02F-W or
QSMBA0SRM003
#
ZENER DIODE RD33FB
QDQZ000RD33F
IC:EEPROM CAT24WC02JI or
NSZBA0SBG001
D616#
SCHOTTKY BARRIER DIODE 21DQ04 or
QDQZ0021DQ04
IC(EEP-ROM) M24C02-WMN6 or
NSZAA0SSS004
#
SCHOTTKY BARRIER DIODE ERB81-004
AERB81004***
IC BR24L02F-WE2
QSZBA0TRM068
D617#
SCHOTTKY BARRIER DIODE 11EQS04 or
QD4Z011EQS04
IC301
MICRO-COMPUTER/VCD M61275FP-61
QSZAB0RMB133
#
SCHOTTKY BARRIER DIODE ERA81-004
QDPZERA81004
IC401
IC:Y/C/A LA71205M-MPB-E
QSZBA0RSY037
D618#
SCHOTTKY BARRIER DIODE 11EQS04 or
QD4Z011EQS04
IC551#
VERTICAL OUTPUT IC LA78040A
QSBBA0SSY003
ICS
QSZBA0SHT019
#
SCHOTTKY BARRIER DIODE ERA81-004
QDPZERA81004
IC601#
PHOTOCOUPLER LTV-817B-F or
NPEB0LTV817F
D619
DIODE FR104-B
NDLZ000FR104
#
PHOTOCOUPLER LTV-817C-F or
NPEC0LTV817F
D620#
ZENER DIODE MTZJT-776.8B or
QDTB0MTZJ6R8
#
PHOTO COUPLER PC817X6
QPE600PC817X
#
ZENER DIODE DZ-6.8BSBT265
NDTB0DZ6R8BS
IC602#
VOLTAGE REGULATOR KIA7805API or
NSBBA0SJY011
D621
D622
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
#
VOLTAGE REGULATOR KA7805A
NSZBA0SF3052
SWITCHING DIODE 1N4148
NDTZ001N4148
IC801
AUDIO AMP IC AN17811A
QSZAA0SMS015
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
COILS
SWITCHING DIODE 1N4148
NDTZ001N4148
L001
PCB JUMPER D0.6-P5.0
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
L031
PCB JUMPER D0.6-P5.0
JW5.0T
SWITCHING DIODE 1N4148
NDTZ001N4148
L033
INDUCTOR 15µH-J-26T or
LLAXJATTU150
D625
CARBON RES. 1/4W J 220 Ω
RCX4JATZ0221
INDUCTOR 15µH-K-26T
LLAXKDTKA150
D626
ZENER DIODE MTZJT-7736A or
QDTA00MTZJ36
L041
PCB JUMPER D0.6-P5.0
JW5.0T
ZENER DIODE DZ-36BSAT265
NDTA00DZ36BS
L202
INDUCTOR 0.10µH-K-26T
LLAXKATTUR10
D627#
ZENER DIODE MTZJT-7713B or
QDTB00MTZJ13
L211#
CHOKE COIL 47µH-K or
LLBD00PKV007
#
ZENER DIODE DZ-13BSBT265
NDTB00DZ13BS
#
CHOKE COIL 47µH-K
LLBD00PKV005
D628
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
L302
PCB JUMPER D0.6-P5.0
JW5.0T
SWITCHING DIODE 1N4148
NDTZ001N4148
L303
PCB JUMPER D0.6-P5.0
JW5.0T
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
L402
INDUCTOR 22µH-J-26T or
LLAXJATTU220
SWITCHING DIODE 1N4148
NDTZ001N4148
INDUCTOR 22µH-K-26T
LLAXKDTKA220
ZENER DIODE MTZJT-776.8A or
QDTA0MTZJ6R8
CHOKE COIL 47µH-K or
LLBD00PKV007
ZENER DIODE DZ-6.8BSAT265
NDTA0DZ6R8BS
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
D623
D629
D631
D632
D633
D634
D635
D636
D638
D640
D641#
L403
L404
JW5.0T
CHOKE COIL 47µH-K
LLBD00PKV005
CHOKE COIL 47µH-K or
LLBD00PKV007
SWITCHING DIODE 1N4148
NDTZ001N4148
CHOKE COIL 47µH-K
LLBD00PKV005
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
L601#
LINE FILTER SA-91213B or
LLBG00ZSA002
SWITCHING DIODE 1N4148
NDTZ001N4148
#
LINE FILTER 5.0MH 6Y075
LLBG00ZKT004
ZENER DIODE MTZJT-778.2B or
QDTB0MTZJ8R2
L601
LINE FILTER UU10.5-A
LLBG00ZY2008
ZENER DIODE DZ-8.2BSBT265
NDTB0DZ8R2BS
L871
PCB JUMPER D0.6-P5.0
JW5.0T
L872
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
SWITCHING DIODE 1SS133(T-77) or
QDTZ001SS133
SWITCHING DIODE 1N4148
NDTZ001N4148
ZENER DIODE MTZJT-7736A or
QDTA00MTZJ36
20040106
INDUCTOR 47µH-K-5FT or
LLARKBSTU470
INDUCTOR 47µH-K-5FT
LLARKDSKA470
TRANSISTORS
Q205
Q206
1-16-4
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
PHOTO TRANSISTOR MID-32A22F or
NPWZ1D32A22F
PHOTO TRANSISTOR PT204-6B-12
NPWZT2046B12
T5553EL
Ref. No.
Q301
Description
Part No.
Ref. No.
Description
Part No.
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
R002
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
R003
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
RRXAJB5Z0101
RESISTORS
TRANSISTOR 2SA1175(F) or
QQSF02SA1175
R032
CHIP RES.(1608) 1/10W J 100 Ω
TRANSISTOR KTA1267(GR) or
NQS10KTA1267
R033
CHIP RES.(1608) 1/10W J 390k Ω
RRXAJB5Z0394
TRANSISTOR 2SA1015-GR(TPE2)
QQS102SA1015
R034
CHIP RES.(1608) 1/10W J 150 Ω
RRXAJB5Z0151
TRANSISTOR 2SA1175(F) or
QQSF02SA1175
R035
CHIP RES.(1608) 1/10W J 220k Ω
RRXAJB5Z0224
TRANSISTOR KTA1267(GR) or
NQS10KTA1267
R036
CHIP RES.(1608) 1/10W J 220k Ω
RRXAJB5Z0224
TRANSISTOR 2SA1015-GR(TPE2)
QQS102SA1015
R037
CHIP RES.(1608) 1/10W J 180 Ω
RRXAJB5Z0181
Q571#
TRANSISTOR TT2138LS-YB11 or
QQZZ00TT2138
R038
CHIP RES.(1608) 1/10W J 150 Ω
RRXAJB5Z0151
#
TRANSISTOR 2SC5884000RF
QQZZ02SC5884
R039
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
Q572
TRANSISTOR 2SC1627Y-TPE2
QQSY02SC1627
R040
CHIP RES.(1608) 1/10W J 2.7k Ω
RRXAJB5Z0272
Q591#
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
R041
CHIP RES.(1608) 1/10W J 18k Ω
RRXAJB5Z0183
#
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
R042
CARBON RES. 1/4W J 3.9k Ω
RCX4JATZ0392
#
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
R201
CARBON RES. 1/4W G 4.7k Ω
RCX4GATZ0472
Q601#
MOS FET 2SK3563
QFWZ02SK3563
R202
CHIP RES. 1/10W F 22k Ω or
RRXAFB5J2202
Q602#
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
CHIP RES.(1608) 1/10W F 22k Ω
RRXAFB5H2202
#
TRANSISTOR 2SC2120-Y(TPE2)
QQSY02SC2120
Q604
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
Q606#
TRANSISTOR 2SA950(O) or
Q2SA9500TPE2
#
TRANSISTOR 2SA950(Y) or
#
Q607
Q401
Q402
R203
R204
CHIP RES. 1/10W F 470 Ω or
RRXAFB5J4700
CHIP RES.(1608) 1/10W F 470 Ω
RRXAFB5H4700
CHIP RES. 1/10W F 1.5k Ω or
RRXAFB5J1501
CHIP RES.(1608) 1/10W F 1.5k Ω
RRXAFB5H1501
R205
CHIP RES. 1/10W F 3.6k Ω or
RRXAFB5J3601
CHIP RES.(1608) 1/10W F 3.6k Ω
RRXAFB5H3601
R206
CHIP RES. 1/10W F 10k Ω or
RRXAFB5J1002
CHIP RES.(1608) 1/10W F 10k Ω
RRXAFB5H1002
Q2SA950YTPE2
R208
CHIP RES.(1608) 1/10W J 22k Ω
RRXAJB5Z0223
TRANSISTOR KTA1271(Y)
NQSY0KTA1271
R209
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
R210
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
R211
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
R212
CHIP RES.(1608) 1/10W J 2.2k Ω
RRXAJB5Z0222
Q608#
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
R213
CHIP RES.(1608) 1/10W J 2.7k Ω
RRXAJB5Z0272
#
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
R214
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
#
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
R215
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
Q609
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
R216
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
R217
CHIP RES.(1608) 1/10W J 2.2k Ω
RRXAJB5Z0222
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
R218
CHIP RES.(1608) 1/10W J 2.7k Ω
RRXAJB5Z0272
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
R219
CHIP RES.(1608) 1/10W J 1k Ω
RRXAJB5Z0102
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
R220
CHIP RES.(1608) 1/10W J 390k Ω
RRXAJB5Z0394
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
R221
PCB JUMPER D0.6-P5.0
JW5.0T
TRANSISTOR 2SC2785(F) or
QQSF02SC2785
R222
CHIP RES.(1608) 1/10W J 270k Ω
RRXAJB5Z0274
TRANSISTOR KTC3199(GR) or
NQS10KTC3199
R223
CHIP RES.(1608) 1/10W J 560 Ω
RRXAJB5Z0561
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
R224
CHIP RES.(1608) 1/10W J 47k Ω
RRXAJB5Z0473
RES. BUILT-IN TRANSISTOR KRA103M or
NQSZ0KRA103M
R225
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
RES. BUILT-IN TRANSISTOR BN1F4M-T
QQSZ00BN1F4M
R226
CHIP RES.(1608) 1/10W J 33k Ω
RRXAJB5Z0333
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
R227
CARBON RES. 1/4W J 270 Ω
RCX4JATZ0271
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
R229
CHIP RES.(1608) 1/10W J 330 Ω
RRXAJB5Z0331
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
R232
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
TRANSISTOR 2SA1175(F) or
QQSF02SA1175
R233
CHIP RES.(1608) 1/10W J 2.2k Ω
RRXAJB5Z0222
TRANSISTOR KTA1267(GR) or
NQS10KTA1267
R234
CHIP RES.(1608) 1/10W J 1.2k Ω
RRXAJB5Z0122
TRANSISTOR 2SA1015-GR(TPE2)
QQS102SA1015
R235
CHIP RES.(1608) 1/10W J 47 Ω
RRXAJB5Z0470
TRANSISTOR 2SC2120-O-TPE2 or
QQS002SC2120
R236
CHIP RES.(1608) 1/10W J 100k Ω
RRXAJB5Z0104
TRANSISTOR 2SC2120-Y(TPE2) or
QQSY02SC2120
R237
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
TRANSISTOR KTC3203(Y)
NQSY0KTC3203
R238
CHIP RES.(1608) 1/10W J 470k Ω
RRXAJB5Z0474
TRANSISTOR 2SC3331(T) or
QSC3331TNPAA
R239
CHIP RES.(1608) 1/10W J 2.7k Ω
RRXAJB5Z0272
TRANSISTOR 2SC3331(U) or
QSC3331UNPAA
R240
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
R241
CHIP RES.(1608) 1/10W J 5.6k Ω
RRXAJB5Z0562
TRANSISTOR 2SC3331(T) or
QSC3331TNPAA
R243
CHIP RES.(1608) 1/10W J 1k Ω
RRXAJB5Z0102
TRANSISTOR 2SC3331(U) or
QSC3331UNPAA
R244
CHIP RES.(1608) 1/10W J 1M Ω
RRXAJB5Z0105
Q605
Q610
Q611
Q612
Q613
Q871
Q872
Q873
Q874
Q875
TRANSISTOR 2SC1815-GR(TPE2)
QQS102SC1815
R245
CHIP RES.(1608) 1/10W J 470 Ω
RRXAJB5Z0471
RES. BUILT-IN TRANSISTOR KRA103M or
NQSZ0KRA103M
R247
CHIP RES.(1608) 1/10W J 820 Ω
RRXAJB5Z0821
RES. BUILT-IN TRANSISTOR BN1F4M-T
QQSZ00BN1F4M
20040106
1-16-5
T5553EL
Ref. No.
Description
Part No.
Ref. No.
CHIP RES.(1608) 1/10W J 470 Ω
RRXAJB5Z0471
R426
R249
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
R250
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
R251
CHIP RES.(1608) 1/10W J 3.3k Ω
R252
Description
Part No.
CHIP RES.(1608) 1/10W J 2.2k Ω
RRXAJB5Z0222
R427
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R428
CHIP RES.(1608) 1/10W J 680k Ω
RRXAJB5Z0684
RRXAJB5Z0332
R429
CHIP RES.(1608) 1/10W J 1.2k Ω
RRXAJB5Z0122
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
R431
CHIP RES.(1608) 1/10W J 8.2k Ω
RRXAJB5Z0822
R253
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
R432
CHIP RES.(1608) 1/10W J 1.8k Ω
RRXAJB5Z0182
R254
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
R544
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R255
PCB JUMPER D0.6-P5.0
JW5.0T
R551
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
R256
CHIP RES.(1608) 1/10W J 5.6k Ω
RRXAJB5Z0562
R552#
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R257
PCB JUMPER D0.6-P5.0
JW5.0T
R556
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R258
PCB JUMPER D0.6-P5.0
JW5.0T
R557
CARBON RES. 1/4W J 470 Ω
RCX4JATZ0471
R259
CHIP RES.(1608) 1/10W J 5.6k Ω
RRXAJB5Z0562
R558
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R260
PCB JUMPER D0.6-P5.0
JW5.0T
R559
CARBON RES. 1/4W J 3.3k Ω
RCX4JATZ0332
R262
CHIP RES.(1608) 1/10W J 220k Ω
RRXAJB5Z0224
R560
CARBON RES. 1/4W J 10k Ω
RCX4JATZ0103
R263
CHIP RES.(1608) 1/10W J 39k Ω
RRXAJB5Z0393
R561
CARBON RES. 1/4W J 8.2k Ω
RCX4JATZ0822
R267
CHIP RES.(1608) 1/10W J 82k Ω
RRXAJB5Z0823
R562
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R269
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
R563
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R270
CHIP RES.(1608) 1/10W J 220k Ω
RRXAJB5Z0224
R565
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R273
CHIP RES.(1608) 1/10W J 1.8k Ω
RRXAJB5Z0182
R566
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R274
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
R570
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R275
CHIP RES.(1608) 1/10W J 22k Ω
RRXAJB5Z0223
R571
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R278
CHIP RES.(1608) 1/10W J 1k Ω
RRXAJB5Z0102
R573
CARBON RES. 1/4W J 470 Ω
RCX4JATZ0471
R279
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R574#
METAL OXIDE FILM RES. 2W J 1k Ω or
RN02102ZU001
R283
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
#
METAL OXIDE FILM RES. 2W J 1k Ω
RN02102DP004
R291
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R575#
METAL OXIDE FILM RES. 2W J 1k Ω or
RN02102ZU001
R292
CHIP RES.(1608) 1/10W J 22k Ω
RRXAJB5Z0223
#
METAL OXIDE FILM RES. 2W J 1k Ω
RN02102DP004
R301
CARBON RES. 1/4W J 330 Ω
RCX4JATZ0331
R576
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
R303
CARBON RES. 1/4W J 330 Ω
RCX4JATZ0331
R577
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R305
CARBON RES. 1/4W J 330 Ω
RCX4JATZ0331
R578
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R308
CARBON RES. 1/4W J 120k Ω
RCX4JATZ0124
R579
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R310
CHIP RES.(1608) 1/10W J 180k Ω
RRXAJB5Z0184
R580
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R312
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
R581
CARBON RES. 1/4W J 56 Ω
RCX4JATZ0560
R314
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
R583#
METAL OXIDE FILM RES. 1W J 2.2 Ω or
RN012R2ZU001
R315
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
#
METAL OXIDE FILM RES. 1W J 2.2 Ω
RN012R2DP003
R316
CHIP RES.(1608) 1/10W J 8.2k Ω
RRXAJB5Z0822
R584
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
R329
CHIP RES.(1608) 1/10W J 15k Ω
RRXAJB5Z0153
R587#
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R331
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
R588
CARBON RES. 1/4W J 100k Ω
RCX4JATZ0104
R332
CARBON RES. 1/2W J 39 Ω or
RCX2JZQZ0390
R590
METAL OXIDE FILM RES. 1W J 3.3k Ω or
RN01332ZU001
R248
CARBON RES. 1/2W J 39 Ω
RCX2390KA013
METAL OXIDE FILM RES. 1W J 3.3k Ω
RN01332DP003
R333
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
R592#
CARBON RES. 1/4W J 180k Ω
RCX4JATZ0184
R334
CHIP RES.(1608) 1/10W J 56k Ω
RRXAJB5Z0563
R593
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R335
CHIP RES.(1608) 1/10W J 5.6k Ω
RRXAJB5Z0562
R594
CHIP RES.(1608) 1/10W J 56k Ω
RRXAJB5Z0563
R336
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R595
CARBON RES. 1/4W J 15k Ω
RCX4JATZ0153
R337
CHIP RES.(1608) 1/10W J 470 Ω
RRXAJB5Z0471
R596
CHIP RES.(1608) 1/10W J 6.8k Ω
RRXAJB5Z0682
R338
CHIP RES.(1608) 1/10W J 18k Ω
RRXAJB5Z0183
R597
CHIP RES.(1608) 1/10W J 470 Ω
RRXAJB5Z0471
R339
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R598
CHIP RES.(1608) 1/10W J 22k Ω
RRXAJB5Z0223
R340
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
R599
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R405
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R602#
CEMENT RES. 3W K 1.2 Ω or
RW031R2PG007
R406
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
#
CEMENT RES. 5W K 1.2 Ω or
RW051R2DP005
R407
CHIP RES.(1608) 1/10W J 18k Ω
RRXAJB5Z0183
#
CEMENT RESISTOR 5W K 1.2 Ω or
RW051R2PG001
R408
CHIP RES.(1608) 1/10W J 18k Ω
RRXAJB5Z0183
#
CEMENT RESISTOR 5W J 1.2 Ω H:10MM or
RW051R2PAK10
R409
CHIP RES.(1608) 1/10W J 39k Ω
RRXAJB5Z0393
#
CEMENT RESISTOR 3W K 1.2 Ω
RW031R2PAK10
R410
CHIP RES.(1608) 1/10W J 3.3k Ω
RRXAJB5Z0332
R603#
METAL OXIDE FILM RES. 2W J 0.39 Ω or
RN02R39ZU001
R414
CHIP RES.(1608) 1/10W J 47k Ω
RRXAJB5Z0473
#
METAL OXIDE FILM RES. 2W J 0.39 Ω
RN02R39DP004
R415
CHIP RES.(1608) 1/10W J 1.5k Ω
RRXAJB5Z0152
R604#
CARBON RES. 1/4W J 1.5M Ω
RCX4JATZ0155
R417
CHIP RES.(1608) 1/10W J 220 Ω
RRXAJB5Z0221
R605
CARBON RES. 1/4W J 1.2M Ω
RCX4JATZ0125
R418
CHIP RES.(1608) 1/10W J 330 Ω
RRXAJB5Z0331
R606
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R419
CARBON RES. 1/4W J 330 Ω
RCX4JATZ0331
R607
CARBON RES. 1/4W J 220 Ω
RCX4JATZ0221
R423
CHIP RES.(1608) 1/10W J 3.9M Ω
RRXAJB5Z0395
R608
CARBON RES. 1/4W J 220k Ω
RCX4JATZ0224
R424
CHIP RES.(1608) 1/10W J 100k Ω
RRXAJB5Z0104
R610
CARBON RES. 1/4W J 1k Ω
RCX4JATZ0102
R425
CHIP RES.(1608) 1/10W J 82k Ω
RRXAJB5Z0823
R613
CARBON RES. 1/4W J 150 Ω
RCX4JATZ0151
20040106
1-16-6
T5553EL
Ref. No.
Description
Part No.
Ref. No.
Description
Part No.
R614
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R856
CARBON RES. 1/4W J 22k Ω
RCX4JATZ0223
R616
CARBON RES. 1/4W J 1 Ω
RCX4JATZ01R0
R857
CHIP RES.(1608) 1/10W J 3.9k Ω
RRXAJB5Z0392
R617
CARBON RES. 1/4W J 180 Ω
RCX4JATZ0181
R862
PCB JUMPER D0.6-P5.0
JW5.0T
R618
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R863
CHIP RES.(1608) 1/10W J 1k Ω
RRXAJB5Z0102
R619
PCB JUMPER D0.6-P12.5
JW12.5T
R864
CHIP RES.(1608) 1/10W J 22k Ω
RRXAJB5Z0223
R620
METAL OXIDE FILM RES. 2W J 10k Ω or
RN02103ZU001
R865
CHIP RES.(1608) 1/10W J 8.2k Ω
RRXAJB5Z0822
METAL OXIDE FILM RES. 2W J 10k Ω
RN02103DP004
R866
CHIP RES.(1608) 1/10W J 12k Ω
RRXAJB5Z0123
R621#
CARBON RES. 1/4W J 12k Ω
RCX4JATZ0123
R867
CHIP RES.(1608) 1/10W J 270 Ω
RRXAJB5Z0271
R622
CARBON RES. 1/4W J 12k Ω
RCX4JATZ0123
R868
CHIP RES.(1608) 1/10W J 330k Ω
RRXAJB5Z0334
R623
CARBON RES. 1/4W J 33k Ω
RCX4JATZ0333
R871
CHIP RES.(1608) 1/10W J 1k Ω
RRXAJB5Z0102
R624#
CARBON RES. 1/4W J 39k Ω
RCX4JATZ0393
R872
CHIP RES.(1608) 1/10W J 22k Ω
RRXAJB5Z0223
R625#
CARBON RES. 1/4W J 39k Ω
RCX4JATZ0393
R873
CARBON RES. 1/4W J 18k Ω
RCX4JATZ0183
R629
CARBON RES. 1/4W J 13k Ω
RCX4JATZ0133
R874
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
R630
CARBON RES. 1/4W J 13k Ω
RCX4JATZ0133
R875
CHIP RES.(1608) 1/10W J 2.2k Ω
RRXAJB5Z0222
R631
CARBON RES. 1/4W J 13k Ω
RCX4JATZ0133
R876
CHIP RES.(1608) 1/10W J 2.2k Ω
RRXAJB5Z0222
R632
CARBON RES. 1/4W J 680 Ω
RCX4JATZ0681
R877
CARBON RES. 1/4W J 820 Ω
RCX4JATZ0821
R633
CARBON RES. 1/4W J 5.6k Ω
RCX4JATZ0562
R980
CARBON RES. 1/4W J 6.8k Ω
RCX4JATZ0682
R634
CHIP RES.(1608) 1/10W J 6.8k Ω
RRXAJB5Z0682
R981
CARBON RES. 1/2W J 1.2 Ω
RCX2JZQZ01R2
R635
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
METAL OXIDE FILM RES. 2W J 10k Ω or
RN02103ZU001
METAL OXIDE FILM RES. 2W J 10k Ω
RN02103DP004
R639#
CARBON RES. 1/2W J 1k Ω or
RCX2JZQZ0102
#
CARBON RES. 1/2W J 1k Ω
RCX2102KA013
R640
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R641
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R642
CHIP RES.(1608) 1/10W J 8.2k Ω
RRXAJB5Z0822
R643
PCB JUMPER D0.6-P5.0
JW5.0T
R644
CHIP RES.(1608) 1/10W J 47k Ω
RRXAJB5Z0473
R645
CARBON RES. 1/4W J 5.6 Ω
RCX4JATZ05R6
R637
SWITCHES
SW201
SW202
SW203
SW204
SW205
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
CARBON RES. 1/2W J 3.9 Ω or
RCX2JZQZ03R9
CARBON RES. 1/2W J 3.9 Ω
RCX23R9KA013
R648
CARBON RES. 1/4W J 5.6 Ω
RCX4JATZ05R6
R650
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R651#
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R652#
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R653
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
R654
CARBON RES. 1/4W J 2.2 Ω
RCX4JATZ02R2
R655#
CARBON RES. 1/4W J 2.2k Ω
RCX4JATZ0222
R656
CARBON RES. 1/4W J 8.2 Ω
RCX4JATZ08R2
R657
CARBON RES. 1/4W J 4.7 Ω
RCX4JATZ04R7
R659
CHIP RES.(1608) 1/10W J 100 Ω
RRXAJB5Z0101
LEAF SWITCH MXS00052MPP0 or
SSC0101MCE01
R660
PCB JUMPER D0.6-P5.0
JW5.0T
LEAF SWITCH MXS00981MPP0
SSC0101MCE02
R661
CARBON RES. 1/4W J 8.2 Ω
RCX4JATZ08R2
ROTARY MODE SWITCH SSS-53MD
SSR0106KB003
R662
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R665
CARBON RES. 1/4W J 5.6 Ω
RCX4JATZ05R6
BC571
BEAD INDUCTORS FBA04HA600VB-00
LLBF00STU026
R666
CARBON RES. 1/4W J 5.6 Ω
RCX4JATZ05R6
BC601
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
R667
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
BC602
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
R670
CARBON RES. 1/4W J 100 Ω
RCX4JATZ0101
BC603
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
R701
CHIP RES.(1608) 1/10W J 75 Ω
RRXAJB5Z0750
BC605
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
R801#
METAL OXIDE FILM RES. 1W J 12 Ω or
RN01120ZU001
BC606
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
#
METAL OXIDE FILM RES. 1W J 12 Ω
RN01120DP003
CF031
CERAMIC TRAP 4.5MHz or
FBE455PMR003
R802
CARBON RES. 1/4W J 4.7k Ω
RCX4JATZ0472
4.5M TRAP XT4.5MB2 or
FBE455PLN001
R803
CHIP RES.(1608) 1/10W J 2.2k Ω
RRXAJB5Z0222
CERAMIC TRAP 4.5MHz
FBE455PMS002
R804
CHIP RES.(1608) 1/10W J 5.6k Ω
RRXAJB5Z0562
R805
CHIP RES.(1608) 1/10W J 10k Ω
RRXAJB5Z0103
R806
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R807
CARBON RES. 1/4W J 47 Ω
RCX4JATZ0470
R808
CARBON RES. 1/4W J 47k Ω
R851
R647
SW206
SW207
SW208
SW209
SW210
SW211
SW212
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
TACT SWITCH SKQNAED010 or
SST0101AL055
TACTILE SWITCH KSHG612BT
SST0101HH027
LEAF SWITCH LSA-1142-2AU or
SSC0101KB014
MISCELLANEOUS
CERAMIC FILTER SFSRA4M50CF00-B0 or
FBB455PMR004
4.5M FILTER LTH4.5MCB
FBB455PLN001
CL201
FMN CONNECTOR, TOP 12P 12FMN-BTRK
JCFNG12JG002
CL301
LEAD WIRE WX3001B65512
WX3001B65512
RCX4JATZ0473
CL602
LEAD WIRE WX3001B25505
WX3001B25505
CHIP RES.(1608) 1/10W J 22k Ω
RRXAJB5Z0223
F601#
FUSE 4.00A/125V or
PAGU20CAG402
R852
CHIP RES.(1608) 1/10W J 3.3k Ω
RRXAJB5Z0332
#
FUSE 51MS040L or
PAFC20CHV402
R853
CHIP RES.(1608) 1/10W J 2.2M Ω
RRXAJB5Z0225
20040106
CF032
1-16-7
T5553EL
Ref. No.
Description
CRT CBA
Part No.
#
FUSE STC4A125V U/CT or
PAGE20CW3402
#
FUSE 4.00A/125V
PAGG20CNG402
Ref. No.
Description
CRT CBA
Consists of the following
Part No.
------------
FH601
FUSE HOLDER MSF-015
XH01Z00LY001
FH601#
FUSE HOLDER FH-V-03078
XH01Z00DK001
FH602
FUSE HOLDER MSF-015
XH01Z00LY001
FH602#
FUSE HOLDER FH-V-03078
XH01Z00DK001
CERAMIC CAP. B K 1000pF/2KV or
CA3D102MR030
J145
CHIP RES.(1608) 1/10W 0 Ω
RRXAZB5Z0000
CERAMIC CAP. B K 1000pF/2KV
CCD3DKD0B102
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL1R0
JK701
JK702
CAPACITORS
C501
CERAMIC CAP. B K 1000pF/2KV or
CCD3DKP0B102
RCA JACK(YELLOW) MSP-281V4-B or
JXRL010LY003
RCA JACK 1P:YELLOW DA1-15A3N0S001
JXRL010RP026
ELECTROLYTIC CAP. 1µF/50V M or
CE1JMASDL010
RCA JACK(WHITE) MSP-281V1-B or
JXRL010LY005
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASTL1R0
C502
RCA JACK 1P:WHITE DA1-15A4N0S001
JXRL010RP025
C511
CHIP CERAMIC CAP. B K 390pF/50V
CHD1JKB0B391
EARPHONE JACK MSJ-035-12APC or
JYSL030LY001
C521
CHIP CERAMIC CAP. B K 390pF/50V
CHD1JKB0B391
EARPHONE JACK HTJ-035-1ZEBTZ
JYSL030GE001
C531
CHIP CERAMIC CAP. B K 390pF/50V
CHD1JKB0B391
PS601#
THERMISTOR ZPB45BL7R0A
QNZZ45BL7R0A
RS201
REMOTE RECEIVER PIC-37042LU
USESJRSKK033
SA601#
SURGE ABSORBER 470V+-10PER or
NVQZ10D471KB
CONNECTOR PIN, 1P LV or
1700576
#
SURGE ABSORBER CNR-10D471K
NVQZR10D471K
CONNECTOR PIN, 1P RT-01N-2.3A
1730688
SF001
SAW FILTER SAFGM45M7VHHZC0B03
FBB456PMR008
SG001#
GAP. FNR-G3.10D
FAZ000LD6005
T571#
FLYBACK TRANSFORMER JF0501-3101B or
LTF00CPXB039
#
FLYBACK TRANS BSC23-2603S
LTF00CPS2054
T572
H0RIZONTAL DRIVE TRANS LP2-005
LTH00CPA5005
T601#
SWITCHING TRANS 01746 or
LTT00CPKT089
#
SWICHING TRANS CSA-SW0041
LTT00CPSA117
TB3
HEAD SHIELD(DC) T5400UA
0EM301721
JK801
TB7
LED HOLDER T5400UA
0EM407679
TB9
13VPOW HEAT SINK PHA T5400UA
0EM407602
CONNECTORS
CN505
Q521
Q531
BUSH, LED(F) H3700UD
0VM409508
TB26
13V H/V HEAT SINK PGZ T5400UA
0EM301720
TL2
SCREW, B-TIGHT M3X8 BIND HEAD+ or
GBMB3080
SCREW, B-TIGHT M3X8 BIND HEAD+
GBMB3080
TP201
PCB JUMPER D0.6-P5.0
JW5.0T
TP202
PCB JUMPER D0.6-P25.0
JW25.0T
TP301
PCB JUMPER D0.6-P5.0
JW5.0T
TP302
PCB JUMPER D0.6-P5.0
JW5.0T
TP401
PCB JUMPER D0.6-P5.0
JW5.0T
TP402
PCB JUMPER D0.6-P5.0
JW5.0T
TU001#
TUNER B8135AP or
UTUNNTUSP023
#
TUNER ENV56DC9G3
UTUNNTUMS010
VR601#
CARBON P.O.T. 10k Ω B
VRCB103HH014
W601#
AC CORD PB8K9F9110A-057 or
WAC0172LW008
AC CORD WAC0172AS006 or
WAC0172AS006
#
AC CORD A0A0280-007
WAC0172LTE04
X201
X'TAL 32.768kHz(20PPM) or
FXC323LJNY01
X'TAL 32.768kHz(20PPM) or
FXC323LCT001
X'TAL 32.768kHz(20PPM) or
FXC323LDS002
X'TAL 32.768kHz(20PPM) or
FXC323LQUA01
X'TAL 32.768kHz(20PPM)
FXC323LCHE01
X'TAL HC-49/U 10.6MHz or
FXD106LLN001
X'TAL AT49-10.6
FXD106LDS002
X202
X301
X401
X'TAL 3.579545 MHz or
FXD355LLN003
X'TAL 3.579545MHz(30PPM)
FXD355LCHE01
X'TAL 3.579545MHz(20PPM) or
FXC355LLN003
X'TAL 3.579545MHz(20PPM) or
FXC355LDS001
X'TAL 3.579545MHz(20PPM)
FXC355LCHE01
JTEA001TG001
TRANSISTORS
Q511
TB21
#
PIN CONNECTOR 005P-5100 or
TRANSISTOR 2SC2482 TPE6 or
QQSZ02SC2482
TRANSISTOR 2SC3468(E)-AE or
QQSE02SC3468
TRANSISTOR 2SC3468(D)-AE or
QQSD02SC3468
TRANSISTOR KTC3207
NQSZ0KTC3207
TRANSISTOR 2SC2482 TPE6 or
QQSZ02SC2482
TRANSISTOR 2SC3468(E)-AE or
QQSE02SC3468
TRANSISTOR 2SC3468(D)-AE or
QQSD02SC3468
TRANSISTOR KTC3207
NQSZ0KTC3207
TRANSISTOR 2SC2482 TPE6 or
QQSZ02SC2482
TRANSISTOR 2SC3468(E)-AE or
QQSE02SC3468
TRANSISTOR 2SC3468(D)-AE or
QQSD02SC3468
TRANSISTOR KTC3207
NQSZ0KTC3207
RESISTORS
R510#
METAL OXIDE FILM RES. 1W J 15k Ω or
#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153DP003
R511
CHIP RES.(1608) 1/10W J 15 Ω
RRXAJB5Z0150
R512
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R513
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R515
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R516
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R517
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R520#
METAL OXIDE FILM RES. 1W J 15k Ω or
RN01153ZU001
RN01153ZU001
#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153DP003
R521
CHIP RES.(1608) 1/10W J 15 Ω
RRXAJB5Z0150
R522
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R523
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R525
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R526
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R527
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R530#
METAL OXIDE FILM RES. 1W J 15k Ω or
RN01153ZU001
#
METAL OXIDE FILM RES. 1W J 15k Ω
RN01153DP003
R531
CHIP RES.(1608) 1/10W J 15 Ω
RRXAJB5Z0150
R532
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R533
CARBON RES. 1/4W J 56k Ω
RCX4JATZ0563
R535
CARBON RES. 1/4W J 560 Ω
RCX4JATZ0561
R536
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
R537
CARBON RES. 1/4W J 1.5k Ω
RCX4JATZ0152
MISCELLANEOUS
20040106
CL501A
LEAD WIRE 3P/300MM
WX1T5500-001
CL502A
LEAD WIRE 4P/300MM
WX1T5500-002
JK501#
CRT SOCKET ISMS02S
JSCC220PK003
1-16-8
T5553EL
SENSOR CBA
Ref. No.
Description
SENSOR CBA
Consists of the following
Part No.
0ESA04524
TRANSISTORS
Q201
Q202
PHOTO TRANSISTOR MID-32A22F or
NPWZ1D32A22F
PHOTO TRANSISTOR PT204-6B-12
NPWZT2046B12
PHOTO TRANSISTOR MID-32A22F or
NPWZ1D32A22F
PHOTO TRANSISTOR PT204-6B-12
NPWZT2046B12
20040106
1-16-9
T5553EL
EWC1303A
T5553UD
2004-01-20