Miele DA424V Operating instructions

Installation Instructions
DA424V-6
en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
Installation
Before installation
 Before installing the appliance,
read all of the information contained
in this chapter and also in the
"IMPORTANT SAFETY
INSTRUCTIONS" section.
4 telescopic extension piece holders
for aligning and securing the telescopic
chimney
Installation parts
4 screws M³/₁₆" x ⁵/₁₆" (M4 x 8.5 mm)
for securing the telescopic extension
piece holders.
4 screws, 6 ⁹/₁₆" x 4 ⁵/₁₆" (7 x 110
mm) and
4 plugs, ³/₈" x 3 ¹/₈" (10 x 80 mm)
for securing the hood to the ceiling.
The screws and plugs are designed
for use in solid ceilings only.
The plugs must only be used
together with the included 6 9/16" x
4 5/16" (7 x 110 mm) screws. For
other types of ceiling construction,
alternative fixings will be required.
Make sure the ceiling is able to take
the weight of the hood.
14 screws M³/₁₆" x ⁵/₁₆" (M4 x 8 mm)
for securing the spacer frame and
securing the hood to the installation
frame.
1 screw M³/₁₆" x ⁵/₈" (M4 x 16 mm)
for securing the chimney.
29
Installation
Appliance dimensions
a Mounting area for the exhaust ducting and power cable. In recirculation mode,
only the power cord is required.
b Alternative installation with spacer frame
c A power cord is required to connect the hood to the outlet in the ceiling. With
extraction mode flexible ducting is also required.
Exhaust connection 6" (150 mm)
30
Installation
Distance between cooktop and ventilation hood (S)
Provided a larger distance is not given by the manufacturer of the cooktop,
follow the minimum safety distances between a cooktop and the bottom of the
hood.
Please also observe the information contained in the "IMPORTANT SAFETY
INSTRUCTIONS" section.
Minimum distance S
Cooking appliance
Miele range
Non-Miele
range
Electric Cooktops
24" (610 mm)
Electric Barbeques and Fryers
26" (660 mm)
Multiburner Gas Cooktops
≤ 43,000 BTU/hr (12.6 W),
no burner > 15,000 BTU/hr (4.5 kW).
26" (660 mm)
30" (760 mm)
Multiburner Gas Cooktops
≤ 73,800 BTU/hr (21.6 W),
no burner > 16,500 BTU/hr (4.8 kW)
30" (760 mm)
Multiburner Gas Cooktops
> 73,800 BTU/hr (21.6 W),
or one of the burners > 16,500 BTU/hr (4.8 kW)
Not possible
Single Burner Gas Cooktops
≤ 20,500 BTU/hr (6 kW)
26" (660 mm)
30" (760 mm)
Single Burner Gas Cooktops
> 20,500 BTU/hr (6 kW)
≤ 27,600 BTU/hr (8.1 kW)
30" (760 mm)
Single Burner Gas Cooktops
> 27,600 BTU/hr (8.1 kW)
Not possible
The fully lowered canopy must not go below the minimum distances given.
The height range for the appliance can be extended or limited by moving the
limit switch (see "Installation").
31
Installation
Installation recommendations
Structural support
– When selecting an installation height,
always take the user height into
consideration. Users should have
ample space to work comfortably on
the cooktop and reach the ventilation
hood controls with ease.
– Please note that the greater the
distance from the cooktop, the less
effective the hood is at drawing in the
cooking vapors.
– To achieve optimal vapor extraction,
make sure that the hood covers the
cooktop. The hood should be
positioned centrally over the
cooktop, not to the side or rear.
– The cooktop should be no wider than
the hood. Preferably, it should be
narrower.
– The mounting area must be easily
accessible. The ventilation hood
should be easy to reach and
disassemble in case a service call is
necessary. This should be taken into
consideration when planning the
position of cupboards, shelves,
ceilings or decorative elements in the
vicinity of the ventilation hood.
The hood must be attached to rigid
structural framing that is supported
in its entirety by the ceiling joists, or
to the ceiling joists directly. Do not
attach the plate directly to the ceiling
with anchors, toggle bolts, etc.
Removing the protective film
The housing components are covered
by a protective film to prevent them
from becoming damaged during
transport.
 Please remove this film before
installing the housing components. It
can be peeled off easily without any
additional tools.
32
Installation
85
5/8" m 22 /8"
0
8 m
22
0
mm
 For vented mode:
dai3435aus
 Draw two intersecting lines on the
ceiling.
– Place a section of the exhaust
ducting in the ceiling and feed it
down through the cross-sectional
area as illustrated. Exhaust ducting of
approx. 8" (200 mm) length is
required between the ceiling and the
hood exhaust socket.
– Secure the exhaust ducting to the
exhaust socket, e.g. with a hose clip
(available as an optional accessory)
on flexible ducting.
 Place the power cord and guide it
through the ceiling in the area shown.
A power cord approx. 12" (300 mm)
in length is required between the
ceiling and the hood connectors.
33
Installation
 Use a knife to release the four
spacers and the two covers from the
spacer frame supplied.
 Drill four holes  ³/₈" (10 mm),
approx. 4 ¹/₂" (115 mm) deep for the
plugs supplied.
 Use the spacer frame as a drilling
template. Place it on the ceiling with
the arrows pointing forwards. Using
the notches, align the spacer frame
on the intersecting lines and make
pencil marks for the drill holes.
34
 Place the four plugs in the holes and
screw in the four screws so that they
protrude by approx. 1 ³/₁₆" (30 mm).
Installation
 Loosen the two telescopic extension
piece holders from the installation
frame.
The spacer frame can be installed
between the chimney and the ceiling.
This creates a shadow which gives the
illusion of a gap between the ceiling
and the chimney. This is useful if the
ceiling is not level or is uneven. The
hood is aligned vertically with the
spacers supplied. Visual irregularities
between the chimney and the ceiling
are then concealed by the shadow.
 If you wish to install the hood with the
spacer frame, remove the four inserts
from the fixing holes.
35
Installation
 Mount the spacer frame onto the
installation frame.
 Hang the hood on the four screws,
making sure the controls are at the
front.
 If using the spacer frame, place the
two covers into the fixing holes.
36
Installation
 Place the exhaust ducting onto the
exhaust socket.
 Connect the power cord. See
"Electrical connection."
 Align the installation frame and
secure it with the screws.
The spacers, which were removed
from the spacer frame at the start,
can be used to align the hood
vertically.
37
Installation
 Remove the grease filters from the
hood.
 Push the tower and the telescopic
extension piece upwards and bend
the retaining tabs outwards again to
prevent the tower and telescopic
extension piece from slipping down
again.
 Remove the safety screw for the
tower on the inside of the frame.
38
Installation
When the canopy is lowered, the safety
distance to the cooker may not be
exceeded (see "Appliance
dimensions"). The height range for the
appliance can be extended or limited
by moving the limit switch.
 Press the  button.
The canopy will be lowered to its fullest
extent.
 Check the distance to the cooker.
If the safety distance is undershot, the
limit switch must be readjusted.
 Fit the four telescopic extension
piece holders between the tower and
the telescopic extension piece. The
internal telescopic extension piece
rests on the clamps. When the
screws are tightened, the telescopic
extension piece holders spread out
and push the telescopic extension
piece upwards.
 Loosen the top limit switch.
Tighten the screws only until the top
edge of the telescopic extension
piece is evenly aligned with the
ceiling or the spacer frame.
39
Installation
 Move the canopy to the required
height by pressing the  button and
stop it by pressing the  or 
button.
 Screw on the limit switch opposite
the guide.
 Hold the chimney securely, bend
back the retaining tabs and carefully
lower it.
The chimney will locate in the cut-out in
the canopy.
40
Installation
1x
T20 M4x16
 Insert the safety screw on the inside.
 Carefully remove the protective foil
from the grease filters.
 Reinsert the grease filters.
41
Exhaust duct
WARNING: Danger of toxic fumes.
Gas cooking appliances release
carbon monoxide that can be
harmful or fatal if inhaled.
To reduce the risk of fire and to
properly exhaust air, the exhaust
gases extracted by the hood should
be vented outside of the building
only.
Do not vent exhaust air into spaces
within walls or ceilings or in attics,
crawl spaces or garages.
To reduce the risk of fire, only use
metal ductwork.
Please read and follow the
"IMPORTANT SAFETY
INSTRUCTIONS" to reduce the risk
of personal injury. Follow all local
building codes when installing the
hood.
 Only use smooth pipes or flexible
duct hoses made from nonflammable materials for exhaust
ductwork.
 To achieve the greatest possible air
extraction with the lowest noise
levels, please note the following:
– The diameter of the exhaust duct
should not be less than 6" (150 mm).
– If flat exhaust ducts are used, the
cross section should not be smaller
than that of the exhaust connector.
– The exhaust duct should be as short
and straight as possible.
– If elbows are needed, make sure they
have a large radius.
– The exhaust duct itself must not be
kinked or compressed.
42
– Make sure that all connections are
secure and airtight.
Remember that any constriction of
the airflow will reduce extraction
performance and increase operating
noise.
 If the exhaust duct is to be routed
through an outside wall, we
recommend installing a telescopic
wall vent or a rooftop vent (available
as an optional accessory).
 If the exhaust air is to be conducted
into a vent flue, the intake piece must
be aligned with the flow direction of
the flue.
 When installing the exhaust duct
horizontally, you must slope it away
from the source by at least ³/₈" per
3 ³/₈" (1 cm per meter). This ensures
that condensate cannot drain back
into the ventilation hood.
 If the exhaust duct is to be routed
through rooms, ceiling space etc., the
temperatures in these different areas
may differ greatly, which means that
the problem of condensation will
need to be addressed. The exhaust
duct will need to be insulated.
Exhaust duct
Condensate trap
In addition to insulating the exhaust
duct, we recommend installing a
condensate trap to collect and
evaporate any condensate which might
accumulate.
Condensate traps are available for
exhaust ducts with a diameter of 5"
(125 mm) or 6" (150 mm).
 When installing a condensate trap,
make sure that it is positioned
vertically and, if possible, directly
above the hood outlet duct collar.
The arrow on the housing indicates
the direction of airflow.
43
Electrical connection
WARNING: TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
All electrical work should be
performed by a qualified electrician
in strict accordance with national
regulations (for USA: ANSI-NFPA 70)
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous.
Ensure that power to the appliance is
OFF while installation or repair work
is performed.
Verify that the voltage, load and
circuit rating information found on
the data plate (located behind the
baffle filters), match the household
electrical supply before installing the
hood.
Use only with ventilation hood cordconnection kits that have been
investigated and found acceptable
for use with this model hood.
If there is any question concerning
the electrical connection of this
appliance to your power supply,
please consult a licensed electrician
or call Miele’s Technical Service
Department.
WARNING: THIS APPLIANCE MUST
BE GROUNDED
44
Grounding Instructions
WARNING - Improper grounding can
result in a risk of electric shock.
This appliance must be grounded. In
the event of an electrical short
circuit, grounding reduces the risk of
electric shock by providing a path of
least resistance.plug.
If there is any doubt, have the
electrical system of the house
checked by a qualified electrician.
To increase security before the
machine is installed, it is
recommended to install a protective
switch (30 mA).
 The hood must be hard wired
accordingly:
Black/Red wire: connect to L1 (live)
White wire: connect to N (neutral)
Green wire: connect to GND (ground)
Activating Con@ctivity 2.0
Installation of the Con@ctivity
2.0 stick
In order for you to be able to use the
Con@ctivity 2.0 function, the cooktop
must be equipped with a Con@ctivity
2.0 stick.
 See the relevant installation
instructions of the Con@ctivity 2.0
stick.
Activating the ventilation hood
 The cooktop and hood must be
switched off.
 Press the delayed shut-down button
515 for approx. 10 seconds until
the 1 indicator appears in the fan
level display.
 Then, press the following buttons in
order:
Activating the Con@ctivity 2.0
function
– The "" button,
To use the Con@ctivity 2.0 function, the
radio link between the cooktop and the
ventilation hood must be activated.
– And then the lighting button .
Both appliances must be installed and
operational.
Wireless connection must be activated
on the ventilation hood and the cooktop
at the same time. Activation on the
ventilation hood is described below.
Activation on the cooktop is described
in the relevant operating and installation
instructions. Please refer to the
operating instructions before starting.
Activate the ventilation hood first, then
the cooktop.
– Followed by the "" button,
The hood is in log on / log off mode.
If the wireless connection is already
activated, 2 and 3 will light up at the
same time.
If there is no wireless connection, 2 and
3 will flash constantly (Con@ctivity 2.0
is already activated or a remote control
is logged on).
 To activate Con@ctivity 2.0, press the
"" button.
The search for a wireless connection
will start.
 As this is happening, begin activation
on the cooktop.
45
Activating Con@ctivity 2.0
Activating the cooktop
Activation failed
 While the ventilation hood is
searching for a wireless connection,
start activation on the cooktop.
More information can be found in the
operating instructions for the
cooktop.
 If a wireless connection cannot be
established despite activation of the
Con@ctivity function on the
ventilation hood and cooktop, the
function must first be deactivated
and then reactivated on both
appliances.
 When the cooktop registers that
connection has been established,
confirm activation on the ventilation
hood with the delayed shut-down
button 515. All indicators will go
out.
 Confirm activation on the cooktop.
The Con@ctivity 2.0 function is now
ready for use.
If you do not confirm within 4 minutes,
activation will be canceled.
You only need to carry out the
activation procedure once. If the
appliances are disconnected from the
electricity supply, for example during
a loss of power, they will still remain
activated.
46
Deactivating Con@ctivity 2.0
 Deactivation on the hood is carried
out in the same way as activation, by
selecting "" instead of "."
 To deactivate the burner, please refer
to the corresponding operating
instructions.
Please keep in mind that disabling the
connection will also disable any
remote control function being used.
The remote control must then be
reactivated.
Service and warranty
For faults that you cannot resolve on
your own, please contact your Miele
dealer or Miele Technical Service.
The telephone number for the Technical
Service Department is listed at the back
of these instructions.
When contacting Miele, please state
the model and serial number of your
ventilation hood.
These can be found on the data plate.
Location of the data plate
The data plate is visible once you have
removed the grease filters.
Warranty
For further information, please refer to
your warranty booklet.
47
Technical data
Fan motor
350 W
Height adjustment motor
150 W
LED cooktop lighting
4x3W
Total connected load
512 W
Voltage, frequency
Fuse rating
Weight
120 V AC, 60 Hz
15 A
107.8 lbs (49 kg)
Contains
FCC ID: 2ACUWEI8800
IC: 5669C-EI8800
This device complies with Part 15 of the FCC Rules and with Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
48
Please have the model and serial number
of your appliance available before
contacting Technical Service.
U.S.A.
Canada
Miele, Inc.
Importer
Miele Limited
National Headquarters
9 Independence Way
Princeton, NJ 08540
Phone: 800-843-7231
609-419-9898
609-419-4298
Fax:
www.mieleusa.com
Technical Service & Support
Nationwide
Phone: 800-999-1360
888-586-8056
Fax:
TechnicalService@mieleusa.com
Headquarters and Miele Centre
161 Four Valley Drive
Vaughan, ON L4K 4V8
www.miele.ca
Customer Care Centre
Phone: 800-565-6435
905-532-2272
customercare@miele.ca
Germany
Manufacturer
Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
49
DA 424V-6

en-US
M.-Nr. 10 118 580 / 00