advertisement
• Make sure you read this guide, including the "Safety
COP
ENGLISH
Checking the Package Contents
Check if the following items are included in your camera package.
If anything is missing, contact the retailer from which you purchased the camera.
Camera
Battery Charger
CB-2LB/CB-2LBE
Battery Pack NB-9L
(with Terminal Cover)
2
Interface Cable
IFC-400PCU
Stereo AV Cable
AVC-DC400ST
Y
Wrist Strap
WS-DC7
Getting Started “Canon Customer
Support” Leaflet
DIGITAL CAMERA
Solution Disk
COP
Using the PDF Manuals
Warranty
Card
Also refer to the PDF manuals on the CD-ROM. After installation, shortcut icons appear on the desktop. If the software installation fails, you can find the manuals in the Readme folder on the CD-ROM.
• Camera User Guide (This Guide)
Once you have mastered the basics, use the camera’s many features to shoot more challenging photos.
• Personal Printing Guide
Read when you want to connect the camera to a printer (sold separately) and print.
• Software Guide
Read when you want to use the included software.
• A memory card is not included.
• Adobe Reader is required to view the PDF manuals.
Read This First
Test Shots and Disclaimer
Take some initial test shots and play them back to make sure the images were recorded correctly. Please note that Canon Inc., its subsidiaries and affiliates, and its distributors are not liable for any consequential damages arising from any malfunction of a camera or accessory, including memory cards, that results in the failure of an image to be recorded or to be recorded in a way that is machine readable.
Warning Against Copyright Infringement
The images recorded with this camera are intended for personal use. Do not record images that infringe upon copyright laws without the prior permission of the copyright holder. Please be advised that in certain cases the copying of images from performances, exhibitions, or commercial properties by means of a camera or other device may contravene copyright or other legal rights even if the image was shot for personal use.
Warranty Limitations
Y
This camera’s warranty is only effective in the country of sale. If there is a problem with the camera while abroad, please return it to the country of sale before proceeding with a warranty claim to a Canon Customer Support Help
Desk. For Canon Customer Support contacts, please see the customer
LCD Monitor (Screen)
•
The LCD monitor is produced with extremely high-precision manufacturing techniques. More than 99.99% of the pixels operate to specification, but occasionally non-performing pixels may appear as bright or dark dots. This is not a malfunction and has no effect on the recorded image.
•
The LCD monitor may be covered with a thin plastic film for protection against scratches during shipment. If so, remove the film before using the camera.
Camera Body Temperature
Please take care when operating the camera for an extended period as the camera body may become warm. This is not a malfunction.
3
4
What Do You Want to Do?
Shoot
●
4
Take good people shots
I
Portraits
V
Kids and pets
Facial Expressions
w P
At the beach
Against snow
Shoot various other scenes
Night Scene
Low Light
O
Foliage
t
Fireworks
Shoot with special effects
Super vivid colors
COP
Miniature Effect
●
Focus on faces ..................................................................25, 62, 84
●
Shoot in places where I cannot use the flash (turn off the flash) ....56
●
Take pictures with me in them too (self-timer)...................60, 66, 81
●
Insert the date and time into my shots .........................................59
What Do You Want to Do?
●
View
1
●
Automatically play back pictures (slideshow).............................110
●
Look at my pictures on a TV ......................................................115
●
Look at my pictures on a computer. .............................................33
●
Quickly search pictures ..............................................................108
●
Erase pictures ......................................................................29, 120
Shoot/View Movies
●
●
View movies .................................................................................32
●
Y
E
Shoot fast moving subjects and play them back in slow motion ....99
●
COP
2
Save
●
Save images to a computer .........................................................33
●
Other
3
●
Use the camera abroad........................................................15, 146
●
Understand what is displayed on the screen .............................162
5
Table of Contents
Chapters 1 – 3 explain the basic operations and frequently used functions of this camera. Chapters 4 onward explain the advanced functions, letting you learn more as you read each chapter.
6
Checking the Package Contents .......2
Read This First ..................................3
What Do You Want to Do? ................4
Table of Contents ..............................6
Conventions Used in This Guide .......9
Safety Precautions...........................10
MENU – Basic Operations .............. 47
Changing the Sound Settings ......... 48
Changing the Screen Brightness .... 49
Returning the Camera to Default
Settings ........................................... 50
Power Down)................................... 51
Clock Functions............................... 51
1 Getting Started................... 13
Charging the Battery........................14
Separately) ......................................16
Inserting the Battery.........................17
Inserting the Memory Card ..............18
Formatting ....................................... 52
Turning the Flash Off ...................... 56
Setting the Date and Time ...............20
Setting the Display Language..........22
Taking Pictures (Smart Auto)...........25
Viewing Images ...............................28
Erasing Images................................29
Subjects (Digital Zoom)................... 57
Inserting the Date and Time............ 59
Using the Self-Timer ....................... 60
Shooting in Various Conditions ....... 61
Detecting a Smile and Shooting...... 64
Using the Wink Self-Timer .............. 65
Shooting Movies ..............................30
Using the Face Self-Timer .............. 66
Viewing Movies................................32
High-Speed Continuous Shooting
Transferring Images to a Computer
(High-speed Burst) .......................... 67
for Viewing .......................................33
Accessories .....................................38
Expressions (Best Image Selection)68
Separately Sold Accessories ...........39
Shoot with the Effects of a Fish-Eye
Lens (Fish-eye Effect) ..................... 69
2 Learning More.................... 41
Miniature Model (Miniature Effect) .. 70
Components Guide..........................42
Screen Display.................................44
Indicator ...........................................45
FUNC. Menu – Basic Operations ....46
Table of Contents
Checking for Shut Eyes................... 91
Changing the Color and Shooting ... 92
Yourself...............................71
Shooting Long Exposures ............... 95
Shooting in Program AE ................. 72
Shooting Stitch Assist Images......... 96
Adjusting the Brightness (Exposure
Compensation)................................ 72
Turning the Flash On ...................... 73
Shooting Movies................ 97
(Macro/Infinity) ................................ 73
Changing the Movie Mode .............. 98
Setting (Image Size) ....................... 74
Movies ............................................. 99
Changing the Compression Ratio
(Image Quality) ............................... 74
Changing the ISO Speed ................ 76
Adjusting the White Balance ........... 77
Continuous Shooting....................... 78
(My Colors) ..................................... 79
Changing the Composition with the Focus Lock................................ 82
Editing ........................................... 105
Using the Self-Timer to Prevent
Camera Shake ................................ 80
Customizing the Self-Timer............. 81
Editing Functions............ 107
Quickly Searching Images............. 108
Playback........................................ 109
Camera................................83
Viewing Slideshows....................... 110
Checking the Focus....................... 112
Changing the AF Frame Mode........ 84
Miniature Model (Miniature Effect) .. 99
Changing the Movie Quality .......... 101
Y
Playback Functions ....................... 104
Magnifying Images ........................ 113
Magnifying the Focal Point.............. 85
Displaying Various Images (Smart
Shuffle) .......................................... 113
Shooting with the AF Lock .............. 86
Changing Image Transitions ......... 114
Shooting with Servo AF .................. 86
Changing the Metering Method....... 87
Shooting with the AE Lock .............. 88
Shooting with the FE Lock .............. 88
Shooting with Slow Synchro ........... 89
Shooting (i-Contrast)....................... 90
Red-Eye Correction ........................ 90
Viewing Images on a TV ............... 115
High-Definition TV ......................... 116
Protecting Images ......................... 117
Erasing Images ............................. 120
Tagging Images as Favorites ........ 122
7
8
Table of Contents
(My Category) ................................123
Rotating Images.............................126
Resizing Images ............................127
Trimming........................................128
Adding Effects with the My Colors
Function .........................................129
(i-Contrast).....................................130
Correcting the Red-Eye Effect .......131
8 Printing ............................. 133
Printing Images..............................134
(DPOF) ..........................................136
(DPOF) ..........................................137
Print Added Images .......................140
Settings.............................141
Changing Camera Settings ........... 142
Settings ......................................... 147
Settings ......................................... 151
10Useful Information ...........153
Using Household Power................ 154
Using an Eye-Fi Card.................... 155
Troubleshooting ............................ 157
List of Messages That Appear on
Y the Screen..................................... 162
Handling Precautions .................... 165
Shooting Mode .............................. 166
Playback Mode FUNC. Menu........ 171
Specifications ................................ 172
Index ............................................. 175
Conventions Used in This Guide
•
Icons are used in the text to represent the camera buttons and switches.
•
Language that displays on the screen appears inside [ ] (square brackets).
•
The directional buttons, control dial, and FUNC./SET button are represented by the following icons.
FUNC./SET button
Up button
Left button
Right button
Down button
Control dial
Â
•
•
•
•
: Things you should be careful about
: Troubleshooting tips
: Hints for getting more out of your camera
: Supplemental information
Y
•
(p. xx): Reference pages (“xx” stands for a page number)
•
This guide assumes all functions are at their default settings.
•
The various types of memory cards that can be used in this camera are collectively referred to as memory cards in this guide.
COP
9
10
Safety Precautions
•
Before using the product, please ensure that you read the safety precautions described below. Always ensure that the product is used correctly.
•
The safety precautions noted on the following pages are intended to prevent injuries to yourself and other persons, or damage to the equipment.
•
Be sure to also check the guides included with any separately sold accessories you use.
Warning
Denotes the possibility of serious injury or death.
• Do not trigger the flash in close proximity to human eyes.
Exposure to the intense light produced by the flash could damage eyesight. In particular, remain at least one meter (39 inches) away from infants when using the flash.
•
• Store this equipment out of the reach of children and infants.
Strap: Putting the strap around a child’s neck could result in asphyxiation.
• Use only recommended power sources.
Y
• Avoid dropping or subjecting the product to severe impacts.
• To avoid the risk of injury, do not touch the interior of the product if it has been
• dropped or otherwise damaged.
• Stop using the product immediately if it emits smoke, a strange smell, or otherwise behaves abnormally.
equipment.
COP
• Do not let the product come into contact with water (e.g. sea water) or other liquids.
• Do not allow liquids or foreign objects to enter the camera.
This could result in electrical shock or fire.
If liquids or foreign objects come into contact with the camera interior, immediately turn the camera power off and remove the battery.
If the battery charger becomes wet, unplug it from the outlet and consult your camera distributor or the closest Canon Customer Support Help Desk.
• Do not play the supplied CD-ROM(s) in any CD player that does not support data
CD-ROMs.
Playing the CD-ROM(s) in an audio CD player (music player) could damage the speakers. It is also possible to suffer hearing loss from listening with headphones to the loud sounds of a CD-ROM played on a music CD player.
Safety Precautions
• Use only the recommended battery.
• Do not place the battery near or in direct flame.
• Unplug the power cord periodically and wipe away any dust and dirt that has collected on the plug, the exterior of the power outlet, and the surrounding area.
• Do not handle the power cord with wet hands.
• Do not use the equipment in a manner that exceeds the rated capacity of the electrical outlet or wiring accessories. Do not use if the power cord or plug are damaged, or not fully plugged into the outlet.
• Do not allow dirt or metal objects (such as pins or keys) to contact the terminals or plug.
The battery may explode or leak, resulting in electrical shock or fire. This could cause injury and damage the surroundings. In the event that a battery leaks and the battery acid contacts eyes, mouth, skin or clothing, immediately flush with water.
Caution
Y
• Be careful not to bang the camera or subject it to strong impacts or shocks when hanging it by the strap.
•
• Be careful not to bump or push strongly on the lens.
This could lead to injury or damage the camera.
COP
• When using the flash, be careful not to cover it with your fingers or clothing.
This could result in burns or damage to the flash.
• Avoid using, placing or storing the product in the following places.
- Places subject to strong sunlight.
- Places subject to temperatures above 40 °C (104 °F).
- Humid or dusty areas.
These could cause leakage, overheating or an explosion of the battery, resulting in electrical shock, fire, burns or other injuries.
High temperatures may cause deformation of the camera or battery charger casing.
• The slideshow transition effects may cause discomfort when viewed for prolonged periods.
11
12
Safety Precautions
Denotes the possibility of damage to the equipment.
Caution
• Do not aim the camera at bright light sources (the sun, etc.).
Doing so may damage the image sensor.
• When using the camera on a beach or at a windy location, be careful not to allow dust or sand to enter the camera.
This may cause the camera to malfunction.
• In regular use, small amounts of smoke may be emitted from the flash.
This is due to the high intensity of the flash burning dust and foreign materials stuck to the front of the unit. Please use a cotton swab to remove dirt, dust or other foreign matter from the flash to prevent heat build-up and damage to the unit.
•
• Remove and store the battery when you are not using the camera.
If the battery is left inside the camera, damage caused by leakage may occur.
Y
• Unplug the battery charger from the power outlet after charging is complete, or when you are not using it.
• Do not place anything, such as cloth on top of the battery charger while it is charging.
distort, resulting in fire.
COP
• Do not place the battery near pets.
Pets biting the battery could cause leakage, overheating or explosion, resulting in fire or damage.
• Do not sit down with the camera in your pocket.
Doing so may cause malfunctions or damage the screen.
• When putting the camera in your bag, ensure that hard objects do not come into contact with the screen.
• Do not attach accessories to the strap.
Doing so may cause malfunctions or damage the screen.
1
Getting Started
This chapter explains preparations before shooting, how to shoot in
A mode, and then how to view and erase the images you take. The latter part of this chapter explains how to shoot and view movies and transfer images to a computer.
Attaching the Strap/Holding the Camera
Y
•
Be sure to attach the supplied strap to the camera and wrap it around your
•
wrist when shooting to avoid dropping the camera.
COP
Strap
13
Charging the Battery
Use the included charger to charge the battery. Be sure to charge the battery as it is not charged at the time of purchase.
Remove the cover.
14
CB-2LBE
Insert the battery.
●
Align the o marks on the battery and charger, then insert the battery by sliding it in ( ) and down ( ).
CB-2LB
Charge the battery.
●
Y
) and plug the charger into a power outlet ( ).
●
For CB-2LBE: Plug the power cord into
X the charger, then plug the other end into a
COP charging starts.
X
The charge lamp will light green when charging has finished. Charging takes approx. 1 hour and 50 minutes.
Remove the battery.
●
Unplug the battery charger from the power outlet, then remove the battery by sliding it in ( ) and up ( ).
To protect the battery and prolong its life, do not charge it for longer than
24 hours continuously.
Charging the Battery
Approximate Number of Shots That Can Be Taken
Number of Shots
Approx. 150
Playback Time
Approx. 4 hrs. 30 min.
• The number of shots that can be taken is based on the Camera & Imaging Products
Association (CIPA) measurement standard.
• Under some shooting conditions, the number of shots that can be taken may be less than mentioned above.
Battery Charge Indicator
An icon or message will appear on the screen indicating the battery’s charge state.
Display
Sufficient charge.
Y
Summary
Slightly depleted, but sufficient.
(Blinking red) Nearly depleted. Charge the battery.
Depleted. Recharge the battery.
“Change the battery pack.”
•
Using the battery and charger effectively
COP
•
How to store the battery for long periods:
Deplete and remove the battery from the camera. Attach the terminal cover and store the battery. Storing a battery for long periods of time (about a year) without depleting it may shorten its life span or affect its performance.
•
The battery charger can also be used when abroad.
The charger can be used in regions that have 100 – 240 V (50/60 Hz) AC power.
If the plug does not fit the outlet, use a commercially available plug adapter. Do not use electrical transformers for foreign travel as they will cause damage.
•
The battery may develop a bulge.
This is a normal characteristic of the battery and does not indicate a problem.
However, if the battery bulges to the point where it will no longer fit into the camera, please contact a Canon Customer Support Help Desk.
•
If the battery is quickly depleted even after charging, it has reached the end of its life span. Purchase a new battery.
15
16
Compatible Memory Cards (Sold Separately)
•
SD memory cards (2 GB and less)*
•
SDHC memory cards
(more than 2 GB, up to and including 32 GB)*
•
SDXC memory cards
(more than 32 GB)*
•
MultiMediaCards
•
MMCplus memory cards
•
HC MMCplus memory cards
•
Eye-Fi Cards
* This memory card complies with the SD standards. Some cards may not operate properly depending on the brand of card used.
Depending on your computer’s OS version, SDXC memory cards may not make sure that your OS supports this function beforehand.
About Eye-Fi Cards
Y
This product is not guaranteed to support Eye-Fi card functions (including wireless transfer). In case of an issue with an Eye-Fi card, please check with the card manufacturer.
Also note that an approval is required to use Eye-Fi cards in many countries or regions. Without approval, use of the card is not permitted. If it is unclear whether the card has been approved for use in the area, please check with the card manufacturer.
COP
Inserting the Battery
Insert the included battery.
Open the cover.
●
Slide the cover ( ) and open it ( ).
Insert the battery.
●
Insert the battery as shown until it locks into place with a click.
Terminals
●
Be sure to insert the battery in the correct direction or it will not properly lock into place.
Y
Close the cover.
●
Close the cover ( ), and press downward
COP
).
Removing the Battery
●
Open the cover and press the battery lock in the direction of the arrow.
X
The battery will pop up.
17
18
Inserting the Memory Card
Insert a memory card (sold separately).
Check the card’s write-protect tab.
●
If the memory card has a write-protect tab, you will not be able to record images if the tab is in the locked position. Slide the tab up until you hear a click.
Open the cover.
●
Slide the cover ( ) and open it ( ).
Terminals
●
Insert the memory card as shown until it locks into place with a click.
●
Be sure the memory card is oriented correctly. Inserting the memory card in the
COP
●
Close the cover ( ) and press downward as you slide it until it clicks into place ( ).
Removing the Memory Card
●
Open the cover and push the memory card in until you hear a click, then slowly release it.
X
The memory card will pop up.
Inserting the Memory Card
What if [Memory card locked] appears on the screen?
SD, SDHC and SDXC memory cards, and Eye-Fi cards have a write-protect tab.
If this tab is in the locked position, [Memory card locked] will appear on the screen and you will not be able to take or erase images.
Approximate Number of Shots per Memory Card
4 GB
1471
16 GB
6026
Memory Card
Number of Shots
• Values are based on the default settings.
• The number of shots that can be taken will vary depending on camera settings, the subject and the memory card used.
Can you check the number of shots that can be taken?
Y
Number of shots that can be taken
COP
19
Setting the Date and Time
The Date/Time settings screen will appear the first time the camera is turned on. Since the dates and times recorded into your images are based on these settings, be sure to set them.
Turn on the camera.
●
Press the power button.
X The Date/Time screen will appear.
Set the date and time.
●
Press the qr buttons to choose an option.
to set a value.
●
Press the op buttons or turn the  dial
Y
●
Press the m button.
X
Once the date and time have been set, the
Date/Time screen will close.
●
Pressing the power button will turn off the camera.
Reappearing Date/Time screen
Set the correct date and time. If you have not set the date and time, the Date/Time screen will appear each time you turn on the camera.
Daylight saving time settings
If you choose in Step 2 and press the op buttons or turn the  dial and choose , you will set the time to daylight saving (1 hour ahead).
20
Changing the Date and Time
You can change the current date and time settings.
Setting the Date and Time
Display the menus.
●
Press the n button.
Choose [Date/Time] in the
3 tab.
●
Press the qr buttons to choose the 3 tab.
●
Press the op buttons or turn the  dial button.
Y m
●
Follow Steps 2 and 3 on p. 20 to adjust the
setting.
●
Pressing the n button will close the menu.
Date/Time battery
•
The camera has a built-in date/time battery (backup battery) that allows the date/time settings to be retained for about three weeks after the battery pack has been removed.
•
By inserting a charged battery or connecting an AC adapter kit (sold separately,
p. 39) the date/time battery can be charged in about 4 hours even if the camera
is not turned on.
•
If the date/time battery is depleted, the [Date/Time] menu will appear when you
turn the camera on. Follow the steps on p. 20 to set the date and time.
21
22
Setting the Display Language
You can change the language that displays on the screen.
Enter Playback mode.
●
Press the
1 button.
Display the settings screen.
●
Press and hold the m button, then immediately press the n button.
Set the display language.
●
Press the m button.
Y
X
Once the display language has been set, the settings screen will close.
COP
What if the clock appears when the
m button is pressed?
The clock will appear if too much time passes between pressing the m button and the n button in Step 2. If the clock appears, press the m button to remove the clock and repeat Step 2.
You can also change the display language by pressing the n button, choosing the
3 tab, and choosing the [Language] menu item.
Formatting Memory Cards
Before you use a new memory card or one that has been formatted in other devices, you should format the card with this camera.
Formatting (initializing) a memory card erases all data on the memory card.
As you cannot retrieve the erased data, exercise adequate caution before formatting the memory card.
Before formatting an Eye-Fi card (p. 155), be sure to install the software
contained on the card to a computer.
Display the menu.
●
Press the n button.
Choose [Format].
●
Press the qr buttons to choose the 3 tab.
●
Press the op buttons or turn the  dial to choose [Format], then press the m button.
Y
Choose [OK].
COP qr buttons or turn the  dial to choose [OK], then press the m button.
Format the memory card.
●
Press the op buttons or turn the  dial to choose [OK], then press the m button.
X
The memory card will be formatted.
Complete formatting.
X
When formatting ends, [Memory card formatting complete] will appear on the screen.
●
Press the m button.
23
Pressing the Shutter Button
24
Formatting or erasing data on a memory card merely changes the file management information on the card and does not ensure its contents are completely erased. Be careful when transferring or disposing of a memory card. When disposing of a memory card, take precautions such as physically destroying the card to prevent personal information leaks.
The total capacity of the memory card displayed in the formatting screen may be less than indicated on the memory card.
Pressing the Shutter Button
To take images that are in focus, be sure to first press the shutter button lightly (halfway) to focus, then press fully to shoot.
Press halfway
Y
.
●
Press lightly until the camera beeps twice
X and AF frames appear where the camera focused.
COP
(Press fully to shoot)
.
The camera plays the shutter sound and takes the shot.
●
Since the shot is being taken while the shutter sound plays, be careful not to move the camera.
Does the length of the shutter sound change?
•
Since the time required to shoot differs according to the scene you want to take, the length of the shutter sound may change.
•
If the camera or subject moves while the shutter sound is playing, the recorded image may be blurry.
If you shoot without pressing the shutter button halfway, the image may not be in focus.
Taking Pictures (Smart Auto)
Since the camera can determine the subject and shooting conditions, you can let it automatically select the best settings for the scene and just shoot. The camera can also detect and focus on faces, setting the color and brightness to optimal levels.
Turn on the camera.
●
Press the power button.
X
The start-up screen will appear.
Zoom bar
Choose
A mode.
●
Set the mode switch to
A.
●
When you point the camera toward the
Y
X
The icon for the determined scene will appear in the upper right of the screen.
X
The camera will focus on detected faces
X and display frames on them.
COP sides of the screen. These areas cannot be recorded when shooting.
Compose the shot.
●
Moving the zoom lever toward i
(telephoto) will zoom in on your subject, making it appear larger. Moving the lever toward j (wide angle) will zoom out from your subject, making it appear smaller.
(The zoom bar showing the zoom position appears on the screen.)
●
If you move the zoom lever all the way toward j (wide angle) or i (telephoto), you will zoom quickly. If you move it slightly, you will zoom slowly.
25
26
Taking Pictures (Smart Auto)
Focus.
●
Press the shutter button halfway to focus.
X
When the camera focuses, it will beep twice and AF frames will appear where the camera focused.
Several AF frames will appear when the camera focuses on more than one point.
AF Frame
Shoot.
●
X
Y shoot. The flash will automatically fire in low light conditions.
X
The image will appear on the screen for
● about two seconds.
COP an image is displayed by pressing the shutter button again.
What if an icon appears in the upper right of the screen?
The icon for the determined scene will appear in the upper right of the screen. For
details on the icons that appear, see “Scene Icons” (p. 163).
Taking Pictures (Smart Auto)
What if...
• What if the color and brightness of the images do not turn out as expected?
The scene icon (p. 163) that appears on the screen may not match the actual
scene. If this happens, try shooting in
• What if white and gray frames appear when you point the camera toward a subject?
When faces are detected, a white frame appears on the face of the main subject, while gray frames appear on other detected faces. The frames will
follow the subjects within a certain range (p. 84).
If the main subject moves, however, the gray frames will disappear, leaving only the white frame.
• What if a blue frame appears when you press the shutter button halfway?
•
A blue frame appears when a moving subject is detected; the focus and exposure will continuously adjust (Servo AF).
What if the indicator blinks orange and
image.
Y
• What if the camera does not play any sounds?
Pressing the n button while turning on the camera power will turn off all sounds except for warning sounds. To turn the sounds on, press the n button to choose [Mute] in the
3 tab, then press the qr buttons to choose [Off].
•
COP
The subject is too far away for the flash to reach. The effective flash range is approximately 30 cm – 3.5 m (12 in. – 12 ft.) at maximum wide angle ( j), and approximately 1.0 – 2.0 m (3.3 – 6.6 ft.) at maximum telephoto ( i).
• What if the camera beeps once when the shutter button is pressed halfway?
Your subject may be too close. Move the zoom lever toward j and hold it until the lens stops moving. The camera will be at its maximum wide angle setting and you will be able to focus on subjects that are about 1 cm (0.4 in.) or more away from the end of the lens. Move the zoom lever toward i and hold it until the lens stops moving. The camera will be at its maximum telephoto setting and you will be able to focus on subjects that are about 1 m (3.3 ft.) or more away from the end of the lens.
• What if the lamp lights when the shutter button is pressed halfway?
To reduce red-eye and to assist in focusing, the lamp may light when shooting in dark areas.
• What if the
h icon blinks when you try to shoot?
The flash is charging. You can shoot when recharging ends.
27
28
Viewing Images
You can view the images you have taken on the screen.
Enter Playback mode.
●
Press the
1 button.
X The last image you took will appear.
Choose an image.
●
Pressing q or turning the  dial counterclockwise will cycle through the images in the reverse order they were taken, from the newest image to the oldest.
●
Pressing r or turning the  dial
Y newest.
●
The images change more quickly if you keep the qr buttons pressed, but they will
●
The lens will retract after approximately 1 minute elapses.
●
Pressing the
1 button again while the lens is retracted will turn off the power.
Switching to Shooting mode
•
Pressing the shutter button halfway while in Playback mode switches the camera to Shooting mode.
Erasing Images
You can choose and erase images one at a time. Please note that erased images cannot be recovered. Exercise adequate caution before erasing an image.
Enter Playback mode.
●
Press the
1 button.
X The last image you took will appear.
Choose an image to erase.
●
Press the qr buttons or turn the  dial to display an image to erase.
Y
●
After pressing the m button, press op buttons or turn the
 dial to choose a, then press the m button again.
X
[Erase?] appears on the screen.
●
Press the qr buttons or turn the  dial to choose [Erase], then press the m button.
X
The displayed image will be erased.
●
To exit instead of erasing, press the qr buttons or turn the
 dial to choose
[Cancel], then press the m button.
29
30
Shooting Movies
The camera can automatically select all settings so that you can shoot movies just by pressing the movie button. The audio will record in stereo.
If you continue shooting for a long time, the camera may become warm. This is not a malfunction.
Choose
A mode.
●
Set the mode switch to
A.
Remaining Time
Elapsed Time
Compose the shot.
●
Moving the zoom lever toward i will zoom
COP j will zoom out from your subject, making it appear smaller.
Shoot.
Y
●
Press the movie button.
X
The camera will beep once, recording will start, and [ Rec] and the elapsed time will appear on the screen.
●
Once shooting begins, take your finger off the movie button.
●
If you change the composition of your shot during shooting, the focus, brightness and tone will automatically adjust.
Shooting Movies
●
Do not touch the microphone while shooting.
●
Do not press any buttons other than the movie button while shooting. The sound the buttons make will be recorded in the movie.
Microphone
Stop shooting.
●
Press the movie button again.
X The camera will beep twice and stop shooting the movie.
X
The movie will record to the memory card.
X Shooting will automatically stop when the memory card fills.
Magnifying the subject while shooting
Y
Pressing the zoom lever while shooting will zoom in on or out from the subject.
However, operation sounds will be recorded.
icon that appears may not match the actual scene.
•
If you change the composition while shooting so the optimum white balance is not possible, press the Movie button to stop recording, then start recording again. (only when the movie quality is fixed at
•
Movies can be shot by pressing the movie button even when the mode switch is in positions other than
•
When the mode switch is set to
E, you can set each setting for shooting
Estimated Shooting Times
Memory Card
4 GB 16 GB
Shooting Time
14 min. 34 sec.
• Shooting times are based on default settings.
• Maximum clip length is approx. 10 minutes.
59 min. 40 sec.
• Recording may stop even if the maximum clip length has not been reached on some memory cards. SD Speed Class 6 or higher memory cards are recommended.
31
32
Viewing Movies
You can view the movies you have shot on the screen.
Enter Playback mode.
●
Press the
1 button.
X The last image you took will appear.
X
appears on movies.
Choose a movie.
●
Press the qr buttons or turn the  dial to choose a movie, then press the m button.
Y
Play the movie.
COP button.
(Play), then press the
X
The movie will play.
m
●
If you press the m button, the movie will pause and the movie control panel will appear. Press the qr buttons or turn the
 dial to choose
(Play), then press the m button to resume playback.
●
Press the op buttons to adjust the volume.
X
After the movie finishes, appears.
Transferring Images to a Computer for Viewing
What if you can’t play back movies on a computer?
•
Install the included software (p. 34).
•
When watching a movie on a computer, frames may drop, it may not play smoothly, and the audio may stop suddenly depending on the computer’s capabilities.
•
If you use the supplied software to copy the movie back onto the memory card, you can play back the movie smoothly with the camera. For enhanced playback you can also connect the camera to a TV.
CPU
RAM
Transferring Images to a Computer for Viewing
You can use the included software to transfer images you have shot with the
Y
System Requirements
Windows
OS
COP
Computer model
Windows XP Service Pack 3
The above OS should be pre-installed on computers with built-in
USB ports.
Pentium 1.3 GHz or higher (still images), Core2 Duo 2.6 GHz or higher (movies)
Windows 7 (64 bit): 2 GB or more
Windows 7 (32 bit), Windows Vista (64 bit, 32 bit): 1 GB or more
(still images), 2 GB or more (movies)
Windows XP: 512 MB or more (still images), 2 GB or more (movies)
Interface
Free Hard Disk
Space
USB
ZoomBrowser EX: 200 MB or more
CameraWindow: 150 MB or more*
PhotoStitch: 40 MB or more
1,024 x 768 pixels or higher Display
* For Windows XP, Microsoft .NET Framework 3.0 or later (max. 500 MB) must be installed. Installation may take some time depending on your computer’s capabilities.
33
34
Transferring Images to a Computer for Viewing
Macintosh
OS
Computer model
CPU
Mac OS X (v10.4 – v10.6)
The above OS should be pre-installed on computers with built-in
USB ports.
PowerPC G4/G5 or Intel Processor (still images), Core 2 Duo 2.6
GHz or higher (movies)
RAM Mac OS X v10.4 – v10.5: 512 MB or more (still images), 2 GB or more (movies)
Mac OS X v10.6: 1 GB or more (still images), 2 GB or more
(movies)
Interface
USB
ImageBrowser: 250 MB or more
CameraWindow: 150 MB or more
Free Hard Disk
Space
Display
PhotoStitch: 50 MB or more
1,024 x 768 pixels or higher
Preparations
Y
Windows Vista and Mac OS X (v10.5) are used for these explanations.
Install the Software.
COP
Place the CD in the computer’s CD-
ROM drive.
●
Place the supplied CD-ROM (DIGITAL
CAMERA Solution Disk) (p. 2) into the
computer’s CD-ROM drive.
Begin installation.
●
Click [Easy Installation] and follow the on-screen instructions to proceed with the installation.
●
If the [User Account Control] window appears, follow the on-screen instructions to proceed.
Transferring Images to a Computer for Viewing
When the installation finishes, click
[Restart] or [Finish].
Remove the CD-ROM.
●
Remove the CD-ROM when your desktop screen appears.
Macintosh
Place the CD in the computer’s CD-
ROM drive.
●
Place the supplied CD-ROM (DIGITAL
CAMERA Solution Disk) (p. 2) into the
Begin installation.
Y
●
Double-click the on the CD.
●
Click [Install], and follow the on-screen instructions to proceed with the
Connect the camera to the computer.
●
Turn off the camera.
●
Open the cover and insert the small plug of
the included interface cable (p. 2) firmly
into the camera terminal in the direction shown.
●
Insert the interface cable’s larger plug into the computer. For connection details, refer to the user guide provided with the computer.
35
36
Transferring Images to a Computer for Viewing
Turn on the camera.
●
Press the
1 button to turn on the camera.
Open CameraWindow.
Windows
●
Click [Downloads Images From Canon
Camera using Canon CameraWindow].
X
CameraWindow will appear.
●
If CameraWindow does not appear, click the [Start] menu and choose [All
Programs], followed by [Canon Utilities],
[CameraWindow] and [CameraWindow].
Macintosh
Y
X
CameraWindow will appear when you
● establish a connection between the camera and computer.
the CameraWindow icon on the Dock (the bar which appears at the bottom of the desktop).
For Windows 7, use the following steps to display CameraWindow.
Click on the task bar.
In the screen that appears, click the link to modify the program.
Choose [Downloads Images From Canon Camera using Canon
CameraWindow] and click [OK].
Double click .
Transferring Images to a Computer for Viewing
Transfer and View Images
●
Click [Import Images from Camera], and then click [Import Untransferred Images].
X
All images not previously transferred will transfer to the computer. Transferred images will be sorted by date and saved in separate folders in the Pictures folder.
●
When [Image import complete.] appears, click [OK], then click [X] to close
CameraWindow.
●
Turn off the camera and unplug the cable.
●
For details on how to view images using a
Y
You can transfer images even without using the image transfer function in the included software by simply connecting your camera to a computer.
There are, however, the following limitations.
•
It may take a few minutes from when you connect the camera to the
•
COP horizontal orientation.
•
Protection settings for images may be lost when transferred to a computer.
•
There may be problems transferring images or image information correctly depending on the version of the operating system in use, the file size, or the software in use.
•
Some functions in the included software may not be available, such as editing movies, and transferring images to the camera.
37
38
Accessories
Supplied with Camera
Wrist Strap
WS-DC7
Battery Pack NB-9L with
Terminal Cover*
Battery Charger
CB-2LB/CB-2LBE*
DIGITAL CAMERA
Solution Disk
Stereo AV Cable
AVC-DC400ST*
Interface Cable
IFC-400PCU*
Memory Card
USB card reader
COP
Canon-Brand PictBridge Compliant Printers
Windows/Macintosh
TV
HDMI Cable HTC-100
High-Definition TV
Separately Sold Accessories
The following camera accessories are sold separately. Some accessories are not sold in some regions, or may no longer be available.
Power Supplies
Battery Charger CB-2LB/CB-2LBE
●
An adapter for charging Battery Pack NB-
9L.
Battery Pack NB-9L
●
Rechargeable lithium-ion battery.
●
Y household power. Recommended for powering the camera for an extended period of time or when connecting to a
COP
Using Accessories Abroad
The battery charger and the AC adapter kit can be used in regions that have 100 –
240 V (50/60 Hz) AC power.
If the plug does not fit the outlet, use a commercially available plug adapter. Do not use electrical transformers for foreign travel as they will cause damage.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATION.
39
40
Separately Sold Accessories
Flash
High-Power Flash HF-DC1
●
This externally mounted flash can be used to capture photographic subjects that are too distant for the built-in flash to illuminate.
Other Accessories
Printers
SELPHY series
HDMI Cable HTC-100
●
Use this cable to connect the camera to
TV set.
the HDMI™ terminal on a high-definition
Y
Canon-Brand PictBridge Compliant
Printers
●
By connecting your camera to a Canon-
COP use a computer.
For more information, visit your nearest
Canon retailer.
PIXMA series
Use of genuine Canon accessories is recommended.
This product is designed to achieve excellent performance when used with genuine
Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this warranty does not apply to repairs arising out of the malfunction of non-genuine Canon accessories, although you may request such repairs on a chargeable basis.
2
Learning More
This chapter explains the parts of the camera and what appears on the screen, as well as the basic operating instructions.
Y
COP
41
Components Guide
42
Lamp (pp. 60, 66, 80, 81, 147)
Lens
Zoom Lever
Shooting: i (Telephoto) / j (Wide
Playback: k (Magnify) / g (Index)
Mode Switch
Mode Switch
Speaker
Tripod Socket
Memory Card Slot Cover (p. 18)
For shooting movies
You can leave it to the camera to select settings for fully automatic
You can shoot with the best settings for the scene
(p. 61) or choose settings yourself to take various
types of pictures (pp. 55, 71, 83).
Components Guide
Screen (LCD Monitor)
A/V OUT (Audio/Video Output) /
DIGITAL Terminal (pp. 35, 115, 134)
Control Dial
1 (Playback) Button (pp. 28, 32, 107)
Q (Self-Timer) (p. 60) / o Button
eu (Focus Range) (p. 73) / q Button
m FUNC./SET (Function/Set) Button
Y
l (Display) (p. 44) / p Button
Turning the control dial allows you to perform
COP operations, the same operations are possible with the opqr buttons.
If you touch the control dial in a Shooting mode, the function assigned to the position you touch will appear on the screen. When you switch to Playback mode, the function assigned to the dial in Playback mode will appear for a few seconds.
43
44
Screen Display
Switching the Display
You can change the screen display using the
details on information that appears on the screen.
Shooting
Information Display No Information Display
Playback
Y
No Information
Display
Focus Check
Simple Information
Display
Detailed Information COP
Display
You can also switch the display by pressing the p button while the image displays right after shooting. However, Simple Information Display is not available. You can change the display that appears first by pressing the
n button, then choosing [Review info] in the 4 tab (p. 149).
Indicator
Screen Display in Dark Shooting Conditions
The display automatically brightens when shooting in dark conditions, allowing you to check the composition (Night Display function). However, the brightness of the image on the screen, and the brightness of the actual image recorded may be different. Screen noise may appear and the movement of the subject may appear somewhat jagged on the screen. This has no effect on the recorded image.
Overexposure Warning during Playback
In “Detailed Information Display” (p. 44), overexposed areas of the image
flash on the screen.
Histogram during Playback
Dark
Bright
High
Low
●
The graph that appears in “Detailed
Information Display” (p. 164) is called the
Y horizontally, and the amount of brightness vertically. When the graph approaches the right side, the image is bright, but when it approaches the left side, the image is dark, and in this way you can judge the
Indicator
The indicator on the back of the camera (p. 43) will light or blink depending
on the camera’s status.
Colors
Green
Orange
Status
Lights
Blinks
Lights
Blinks
Operation Status
Shooting preparation complete/Display off (p. 145)
Recording/reading/transmitting image data
Shooting preparation complete (flash on)
Camera shake warning (pp. 27, 56)
When the indicator blinks green, data is being recorded/read or various information is being transmitted. Do not turn off the power, open the memory card slot cover/battery cover, shake or jolt the camera. These actions may corrupt the image data or cause the camera or memory card to malfunction.
45
46
FUNC. Menu – Basic Operations
Commonly used functions can be set with the
ø menu.
The menu items and options differ depending on the Shooting mode and
Playback mode (pp. 166 – 169).
Display the
ø menu.
●
Press the m button.
Choose a menu item.
Menu Items
Available Options
●
Press the op buttons or turn the  dial to choose a menu item, then press the m
● or r button.
Y
Choose an option.
●
Press the op buttons or turn the  dial
● to choose an option.
COP
.
●
To return to the menu item, press the q button.
Complete the setting.
●
Press the m button.
X
The shooting screen will reappear and the setting you chose will display on the screen.
MENU – Basic Operations
Various functions can be set from the menus. The menu items are organized under tabs, such as for shooting (
4) and playback (1). The options differ
depending on the Shooting mode and the Playback mode (pp. 168 – 171).
Display the menu.
●
Press the n button.
Choose a tab.
●
Press the qr buttons, or move the zoom
● lever left or right to choose a tab.
Choose an item.
Press the
Y to choose an item.
●
Some items require you to press the m or r button to display a submenu in which
Choose an option.
●
Press the qr buttons to choose an option.
Complete the setting.
●
Press the n button to restore the normal screen.
47
48
Changing the Sound Settings
You can silence or adjust the volume of camera sounds.
Muting Sounds
Display the menu.
●
Press the n button.
Choose [Mute].
●
Press the qr buttons to choose the 3 tab.
●
Press the op buttons or turn the  dial to choose [Mute], then press the qr buttons to choose [On].
●
Press the n button to restore the normal screen.
Y
You can also mute camera sounds by holding down the p button and turning on the power.
Adjusting the Volume
COP
●
Press the n button.
Choose [Volume].
●
Press the qr buttons to choose the 3 tab.
●
Press the op buttons or turn the  dial to choose [Volume], then press the m button.
Change the volume.
●
Press the op buttons or turn the  dial to choose an item, then press the qr buttons to adjust the volume.
●
Press the n button twice to restore the normal screen.
Changing the Screen Brightness
The screen brightness can be changed in two ways.
Using the Menu
Display the menu.
●
Press the n button.
Choose [LCD Brightness].
●
Press the qr buttons to choose the 3 tab.
●
Press the op buttons or turn the  dial
● to choose [LCD Brightness].
Change the brightness.
Press the
Y brightness.
●
Press the n button twice to restore
Using the p Button
● the normal screen.
COP
Press the p button for more than one second.
X
The screen increases to maximum brightness regardless of the setting in the
3 tab.
●
Pressing the p button again for more than one second will return the screen to the original brightness.
•
The next time you turn on the camera, the screen will be at the brightness setting chosen in the
3 tab.
•
When you have set the brightness to its highest setting in the
3 tab, you cannot change the brightness with the p button.
49
50
Returning the Camera to Default Settings
When you have mistakenly changed a setting, you can reset the camera to the default settings.
Display the menu.
●
Press the n button.
Choose [Reset All].
●
Press the qr buttons to choose the 3 tab.
●
Press the op buttons or turn the  dial to choose [Reset All], then press the m
● button.
Reset the settings.
Press the
Y choose [OK], then press the m button.
X
The camera will reset to the default settings.
COP
•
The [Date/Time] (p. 21) in the
3 tab, [Language] (p. 22), [Video System]
(p. 115), [Time Zone] (p. 146), and the image registered in [Start-up Image]
•
The saved data for custom white balance (p. 77).
•
Colors that were chosen in Color Accent (p. 92) or Color Swap (p. 93).
•
Shooting modes set with the mode switch set to
Power Saving Function (Auto Power Down)
To save battery power, the screen turns off, and the camera shuts down automatically when it is not operated for a certain time.
Power Saving during Shooting
The screen will turn off approximately 1 minute after the camera is last operated. After about 2 more minutes, the lens will retract and the power will turn off. When the screen has turned off but the lens has not yet retracted,
pressing the shutter button halfway (p. 24) turns on the screen and shooting
can continue.
Power Saving during Playback
The power will turn off approximately 5 minutes after the camera is last operated.
•
•
Y
Clock Functions
You can check the current time.
COP m button.
X The current time appears.
●
If you hold the camera vertically while using the clock function, it will switch to vertical display. Press the qr buttons or turn the
 dial to change the display color.
●
Press the m button again to cancel the clock display.
When the camera power is off, press and hold the m button, then press the power button to display the clock.
51
52
Low Level Memory Card Formatting
Perform low level formatting when [Memory card error] appears, the camera does not operate properly, or you think that the recording/reading speed of a memory card has dropped. As you cannot retrieve the erased data, exercise adequate caution before formatting the memory card.
Display the menu.
●
Press the n button.
Choose [Format].
●
Press the qr buttons to choose the 3 tab.
●
Press the op buttons or turn the  dial to choose [Format], then press the m button.
Y
Choose [Low Level Format].
●
Press the op buttons or turn the  dial
● to choose [Low Level Format], then press the qr buttons to display
.
COP button.
opqr buttons or turn the  dial to choose [OK], then press the m
Start the low level format.
●
Press the op buttons or turn the  dial to choose [OK], then press the m button.
X
Low level formatting starts.
X
When low level formatting ends, [Memory card formatting complete] will appear.
Complete the low level format.
●
Press the m button.
Low Level Memory Card Formatting
•
Low level formatting may take longer than standard formatting (p. 23),
since all recorded data is erased.
•
You can stop a low level format of a memory card by choosing [Stop].
When stopping low level formatting, the data will be erased but the memory card can be used without problem.
COP
Y
53
54
COP
Y
3
flash.
Shooting with Commonly
Used Functions
This chapter explains how to shoot in different conditions, as well as
Y
COP
•
This chapter assumes the camera is set to
A mode for “Turning the
Flash Off” (p. 56) to “Using the Self-Timer” (p. 60). When shooting in a
mode other than
A, check which functions are available in that mode
•
“Shooting in Various Conditions” (p. 61) to “Take Shots That Look Like a
Miniature Model (Miniature Effect)” (p. 70) assumes that the corresponding
mode has been chosen.
55
56
Turning the Flash Off
You can shoot with the flash turned off.
Press the
r button.
Choose
!.
●
Press the qr buttons or turn the  dial to choose
!, then press the m button.
X Once set,
! will appear on the screen.
●
To turn the flash back on, follow the Steps above to return the setting to .
Y
What if the indicator blinks orange and a flashing appears?
COP
will appear on the screen. Attach the camera to a tripod to prevent it from moving.
Zooming in More Closely on Subjects
(Digital Zoom)
You can use the digital zoom to zoom up to approximately 40x and capture subjects that are too far away for the optical zoom to enlarge. The images
may appear coarse, however, depending on the recording pixel setting (p. 74)
and the zoom factor used.
Move the zoom lever toward
i.
●
Hold the lever until zooming stops.
X
The zoom will stop when the largest possible zoom factor without image deterioration has been reached, and the
Zoom Factor zoom factor will appear when you release the zoom lever.
Move it toward
Y i again.
X
The digital zoom will zoom in even further on the subject.
COP
What if the zoom factor appears in blue?
Images shot at zoom factors that appear in blue will be coarse.
Turning off the digital zoom
To turn off the digital zoom, press the n button to choose [Digital Zoom] in the
4 tab, then choose [Off].
The focal length when using the optical zoom and digital zoom together is
36 – 1440 mm, and 36 – 360 mm when using the optical zoom alone (all focal lengths are 35mm film equivalent).
57
58
Zooming in More Closely on Subjects (Digital Zoom)
Digital Tele-Converter
The focal length of the lens can be increased by approx. 1.4x or approx. 2.3x.
This enables a faster shutter speed and less chance of camera shake than the zoom (including digital zoom) used by itself at the same zoom factor. The images may appear coarse, however, depending on the combination of
recording pixel (p. 74) and digital tele-converter settings used.
Choose [Digital Zoom].
●
Press the n button.
●
Press the qr buttons to choose the 4 tab.
●
Press the op buttons or turn the  dial to choose [Digital Zoom].
Accept the setting.
Y
●
Press the qr buttons to choose a
X magnification.
●
Pressing the n button will restore the
COP factor will appear on the screen.
●
To return to standard digital zoom, choose
[Digital Zoom] and the [Standard] option.
What if the zoom factor appears in blue?
Using this function at a recording pixel setting of deterioration (the zoom factor will appear in blue).
or will cause image
•
The respective focal lengths when using [1.4x] and [2.3x] are 50.4 –
504 mm and 82.8 – 828 mm (35mm film equivalent).
•
The digital tele-converter cannot be used together with the digital zoom.
Inserting the Date and Time
You can insert the shooting date and time in the lower right corner of an image. Once inserted, however, they cannot be deleted. Be sure to check
beforehand that the date and time are correctly set (p. 20).
Choose [Date Stamp].
●
Press the n button.
●
Press the qr buttons to choose the 4 tab.
●
Press the op buttons or turn the  dial to choose [Date Stamp].
Accept the setting.
●
Press the qr buttons to choose [Date] or
●
[Date & Time].
Pressing the
Y shooting screen.
X
Once set, [DATE] will appear on the screen.
Shoot.
COP in the image’s lower right corner.
●
To restore to the original setting, choose
[Off] in Step 2.
You can insert and print the shooting date in images which do not have an embedded date and time as follows. However, if you do this for images with an embedded date and time, the date and time may be printed twice.
•
Use the DPOF print settings (p. 137) to print.
• Use the included software to print.
Refer to the Software Guide for details.
• Print using printer functions.
Refer to the Personal Printing Guide for details.
59
Using the Self-Timer
The self-timer can be used to shoot a group photo that includes the photographer. The camera will shoot approximately 10 seconds after the shutter button is pressed.
Press the
o button.
60
Choose
Ò.
●
Press the op buttons or turn the  dial to choose
Ò, then press the m button.
X Once set,
Ò will appear on the screen.
Y
●
Press the shutter button halfway to focus on the subject, then press it fully.
X
When the self-timer starts, the lamp blinks and the self-timer sound plays.
X
Two seconds before the shutter releases, the lamp and sound speed up (the lamp remains lit when the flash will fire).
●
To cancel shooting with the timer after countdown has started, press the o button.
●
To restore the original setting, choose in Step 2.
You can change the delay time and number of shots (p. 81).
Shooting in Various Conditions
The camera will select the necessary settings for the conditions in which you wish to shoot when you choose the matching mode.
Set the mode switch to
4.
Choose the Shooting mode.
●
After pressing the m button, press the op buttons or turn the  dial to choose
G, then press the m button again.
●
Press the op buttons or turn the  dial to choose a Shooting mode, then press the m button.
Y
Shoot.
●
Produces a soft effect when photographing people.
V Take shots of kids and pets
(Kids&Pets)
●
Lets you capture subjects that move around, such as children and pets, without missing photo opportunities.
●
At maximum wide angle setting you will be able to focus on subjects that are about
1 m (3.3 ft.) or more away from the end of the lens, and at maximum telephoto setting you will be able to focus on subjects that are about 3 m (9.8 ft.) or more away from the end of the lens.
61
62
Shooting in Various Conditions
Take nightscapes without using a tripod (Handheld NightScene)
●
Lets you take beautiful snapshots of city nightscenes by combining several continuous shots to reduce camera shake and noise.
●
When using a tripod, you should shoot in
●
A recording pixel setting of will display, and the image will be fixed at 3648 x 2736
● pixels.
Take shots in low light conditions
(Low Light)
Y camera shake and subject blur.
w
●
A recording pixel setting of will display, and the image will be fixed at 1824 x 1368
COP
(Beach)
●
Lets you take shots of brightly lit people on sandy beaches where the reflected sunlight is strong.
O
Take shots of foliage (Foliage)
●
Lets you shoot trees and leaves, such as new growth, autumn leaves or blossoms, in vivid colors.
Shooting in Various Conditions
P
Take shots of people in snow
(Snow)
●
Lets you take bright, natural-colored shots of people against snowy backgrounds.
t
Take shots of fireworks (Fireworks)
●
Lets you take shots of fireworks in vivid colors.
•
In t mode, attach the camera to a tripod to prevent the camera from moving and blurring the image. Additionally, you should set the [IS Mode]
to [Off] when shooting with a tripod (p. 150).
Y
•
In mode, hold the camera firmly while shooting as multiple images are captured in succession.
•
In
V or
mode, images may appear coarse because the ISO speed
(p. 76) is increased to match the shooting conditions.
•
COP result depending on shooting conditions.
Adding Effects and Shooting
mode, the camera may not be able to combine images or you may not obtain the expected
Shoot images with vivid colors
(Super Vivid)
●
Lets you take shots with vivid, intense colors.
Take posterized shots
(Poster Effect)
●
Lets you take shots that look like an old poster or illustration.
63
Detecting a Smile and Shooting
Since you may not achieve the expected results with images shot in and , try taking some test shots first.
Detecting a Smile and Shooting
The camera will shoot, even without pressing the shutter button, when it detects a smile.
Choose .
●
Follow Steps 1 – 2 on p. 61 to choose
, then press the n button for more than
●
Press the qr buttons or turn the  dial to
X one second.
choose
Y n button.
and [Smile Detection on] will appear on the
● screen.
Point the camera at a person.
COP shoot after the lamp lights.
●
Pressing the o button will pause smile detection. Press the o button again to resume smile detection.
What if a smile is not detected?
Smiles are easier to detect if the subject faces the camera, and opens their mouth enough to show some teeth when smiling.
Changing the number of shots
After choosing in Step 1, press the op buttons.
•
You should switch to another mode when you finish shooting, or the camera will continue taking shots each time the camera detects a smile.
•
You can also shoot by pressing the shutter button.
64
Using the Wink Self-Timer
Point the camera at a person and press the shutter button fully. The camera will shoot approximately two seconds after it detects a wink.
Choose .
●
Follow Steps 1 – 2 on p. 61 to choose
, then press the n button for more than one second.
●
Press the qr buttons or turn the  dial to choose , then press the n button.
Compose the shot and press the shutter button halfway.
●
Confirm that a green frame appears around
Y
Press the shutter button fully.
X The camera will enter shooting stand-by,
X and [Wink to take picture] will appear on the screen.
COP will play.
Face the camera and wink.
X
The shutter will release approximately 2 seconds after a wink is detected from the person with a frame around the person’s face.
●
To cancel the countdown, press the o button.
What if a wink is not detected?
•
Wink a bit slowly.
•
A wink may not be detected if eyes are covered by hair or a hat, or when wearing glasses.
65
Using the Face Self-Timer
Changing the number of shots
After choosing in Step 1, press the op buttons.
•
Shutting both eyes will also be detected as a wink.
•
If a wink is not detected, the shutter will release approximately 15 seconds later.
•
If there are no people in the shot when the shutter button is pressed fully, the camera will shoot after a person enters the shot and winks.
66
Using the Face Self-Timer
The shutter will release approximately two seconds after the camera detects
a new face (p. 84). You can use this when the photographer wants to be in
the image, such as a group photo.
Choose .
Y
●
Follow Steps 1 – 2 on p. 61 to choose
, then press the n button for more than
●
Press the qr buttons or turn the  dial to choose , then press the n button.
Compose the shot and press the shutter button halfway.
●
Make sure a green frame appears on the face focused on and white frames appear on other faces.
Press the shutter button fully.
X The camera will enter shooting stand-by, and [Look straight at camera to start count down] will appear on the screen.
X
The lamp will blink and the self-timer sound will play.
High-Speed Continuous Shooting (High-speed Burst)
Join the subjects and look at the camera.
X
When the camera detects a new face, the lamp and sound will speed up (the lamp remains lit when the flash will fire), and two seconds later the shutter will release.
●
To cancel shooting with the timer after countdown has started, press the o button.
Changing the number of shots
After choosing in Step 1, press the op buttons.
release approximately 15 seconds later.
Y
High-Speed Continuous Shooting
(High-speed Burst)
COP
8.8 images/second while the shutter button is pressed fully and held.
The recording pixel setting will be fixed at (1824 x 1368 pixels).
Choose .
●
Follow Steps 1 – 2 on p. 61 to choose
,
Shoot.
X
As long as you hold the shutter button down, the camera will shoot successive images.
•
Focus, exposure and white balance settings are set with the first shot.
•
Depending on the shooting conditions, camera settings and the zoom position, the shooting speed may slow down.
•
As the number of images increases, the shooting speed may slow down.
67
68
Capturing the Best Facial Expressions
(Best Image Selection)
The camera takes five continuous shots, then detects various aspects of the shot such as facial expressions, and saves only one picture detected as the best.
The recording pixel setting will be fixed at (1824 x 1368 pixels).
Choose .
●
Follow Steps 1 – 2 on p. 61 to choose
.
Shoot.
X
When the shutter button is pressed fully,
•
the camera takes five continuous shots, and saves one picture only.
Y
•
Depending on the shooting condition, you may not obtain the expected result.
COP
Shoot with the Effects of a Fish-Eye Lens
(Fish-eye Effect)
Lets you shoot with the distorting effect of a fish-eye lens.
Choose .
●
Follow Steps 1 – 2 on p. 61 to choose
.
Choose an effect level.
●
Press the n button for more than one second.
X
[Effect Level] will appear on the screen.
●
Press the qr buttons or turn the  dial to
X choose an effect level, then press the n button.
Y
Shoot.
Since you may not achieve the expected results depending on the
COP
69
70
Take Shots That Look Like a Miniature
Model (Miniature Effect)
Blurs chosen portions in the top and bottom of an image to produce the effect of a miniature model.
Choose .
●
Follow Steps 1 – 2 on p. 61 to choose
.
Choose the area to keep in focus.
●
Press the n button for more than one second.
X
A white frame (the area that will not be blurred) appears on the screen.
●
Move the zoom lever to change the frame size, and press the op buttons to change the frame position, then press the n button.
Y
•
Shoot.
COP change the frame vertical orientation and also change the area to focus in. Pressing the op buttons will return the frame to horizontal orientation.
•
Holding the camera vertically will change the orientation of the frame.
•
Since you may not achieve the expected results depending on the shooting conditions, try taking some test shots first.
4
Choosing Settings Yourself
In this chapter you will learn how to use the various functions in
G mode to progressively advance your shooting skills.
Y
•
This chapter assumes that you have set the mode switch to camera is in
G mode.
COP
•
G stands for Program AE.
4 and the
•
Before attempting to shoot using a function explained in this chapter in modes other than
G mode, check if the function is available in those modes
71
72
Shooting in Program AE
You can choose the settings for various functions to suit your preferences.
AE stands for Auto Exposure.
The focusing range is approximately 5 cm (20 in.) – infinity at maximum wide angle ( j), and approximately 1 m (3.3 ft.) – infinity at maximum telephoto
( i).
Enter
G mode.
●
Follow Steps 1 – 2 on p. 61 to choose
G.
Adjust the settings according to
your purposes (pp. 73 – 81).
Shoot.
Y halfway, the shutter speed and aperture value are shown in orange. Try the following settings to obtain the correct exposure.
•
•
Choose a higher ISO speed (p. 76)
COP
You can adjust the standard exposure set by the camera in 1/3-stop increments in the range of -2 to +2.
Enter Exposure Compensation mode.
●
After pressing the m button, press the op buttons or turn the  dial to choose
#, then press the m button again.
Adjust the brightness.
●
While watching the screen, press the op buttons or turn the
 dial to adjust the brightness, then press the m button.
X
The exposure compensation amount will appear on the screen.
Turning the Flash On
You can make the flash fire every time you shoot. The effective flash range is approximately 30 cm – 3.5 m (12 in. – 12 ft.) at maximum wide angle ( j), and approximately 1.0 – 2.0 m (3.3 – 6.6 ft.) at maximum telephoto ( i).
Choose
h.
●
After pressing the r button, press the qr buttons or turn the
 dial to choose h, then press the m button.
X
Once set, h will appear on the screen.
Changing the Focusing Range
(Macro/Infinity)
Y
Choose a focusing range.
●
After pressing the q button, press the qr buttons or turn the
 dial to choose an
COP m button.
The icon for the set mode will appear.
Focusing Range Description
e u
Approx. 1 – 50 cm* (0.4 in. – 1.6 ft.)
Approx. 3 m (9.8 ft.) – infinity
Only focuses on close subjects.
Only focuses on far-away subjects.
* When at the maximum wide angle ( j) setting of the lens.
In macro shooting, the edges of the image may darken if the flash fires.
How can I take better close-ups?
Try attaching the camera to a tripod and shooting in
Î to prevent the camera from
moving and blurring the image (p. 80).
For macro shooting, e will turn gray in the area that displays in the yellow bar underneath the zoom bar, and the camera will not focus.
73
74
Changing the Recording Pixel Setting
(Image Size)
You can choose from five recording pixel (image size) settings.
Choose the recording pixel setting.
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
Choose an option.
●
Press the op buttons or turn the  dial to choose an option, then press the m button.
•
If you choose
X
The setting will appear on the screen.
•
If you press the movie button when the camera is set to , the aspect ratio of the display will change and recording will begin (when set to [640]
COP
You can choose from the following two compression ratios (image quality):
(Fine), (Normal).
Choose the compression ratio setting.
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
Choose an option.
●
Press the op buttons or turn the  dial to choose an option, then press the m button.
X
The setting will appear on the screen.
Changing the Compression Ratio (Image Quality)
Approximate Values for Recording Pixels and Compression
Ratio
Recording Pixels
Compression
Ratio
Single Image Data
Size (Approx. KB)
(Large)
10M/3648x2736
(Medium 1)
6M/2816x2112
2565
1226
1620
780
Number of Shots per
Memory Card
4 GB
1471
16 GB
6026
3017
2320
4641
12354
9503
19007
558 6352 26010
(Medium 2)
2M/1600x1200
(Small)
0.3M/640x480
(Widescreen)
3648x2048
278
150
84
1920
918
Y
12069
20116
30174
1978
4022
49420
82367
123550
8101
16473
• The values in the table are measured according to Canon standards and may change depending on the subject, memory card and camera settings.
A2
A3 – A5
5" x 7"
Postcard size
3.5" x 5"
●
Suitable for sending images as e-mail attachments.
●
For printing on wide size paper.
75
76
Changing the ISO Speed
Choose the ISO speed.
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
Choose an option.
●
Press the op buttons or turn the  dial to choose an option, then press the m button.
X
The setting will appear on the screen.
Automatically adjusts the ISO speed to the Shooting mode and shooting conditions.
Low
High
Fine weather conditions, outdoor shooting.
Cloudy, twilight
Y
Nightscapes, dark interiors
•
Changing the ISO speed
COP
•
Raising the ISO speed results in a faster shutter speed, reducing image blurring and letting the flash reach greater distances to the subject. The images, however, will appear coarse.
When the camera is set to , you can press the shutter button halfway to display the automatically set ISO speed.
Adjusting the White Balance
The white balance (WB) function sets the optimal white balance for natural looking colors to match the shooting conditions.
Choose the white balance function.
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
Choose an option.
●
Press the op buttons or turn the  dial to choose an option, then press the m button.
Auto
Day Light
Cloudy conditions.
X
The setting will appear on the screen.
Automatically sets the optimal white balance for the shooting
Y
Cloudy, shady, twilight conditions
Tungsten
Fluorescent
Custom
Tungsten, bulb-type (3-wavelength) fluorescent lighting
Warm-white fluorescent, cool-white fluorescent, warm-white-type
(3-wavelength) fluorescent lighting
COP
Custom White Balance
You can adjust the white balance to the light source at the shooting location.
Make sure that you set the white balance under the light source of the actual scene you will shoot.
●
In Step 2 above, choose .
●
Make sure the entire screen is filled with a plain, white colored subject, then press the n button.
X
The tint on the screen will change when a white balance data is set.
If you change camera settings after recording white balance data, the tone may not turn out properly.
77
78
Continuous Shooting
As long as you hold the shutter button down, the camera will shoot continuously.
Choose a Drive mode.
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
Mode
W
Continuous
Continuous
Shooting AF
Continuous
Shooting LV*
Maximum Speed
(Approx. images/ sec.)
3.7
0.8
0.9
Choose an option.
●
Press the op buttons or turn the  dial to choose
W or
, then press the m button.
Shoot.
X
Y the camera will shoot successive images.
COP
Description
The camera shoots continuously with the focus and exposure set when the shutter button is pressed halfway.
The camera shoots continuously and focuses.
The [AF Frame] is set to [Center].
In t mode, the focus is locked on the first shot.
* When in
t (p. 63) or AF lock modes (p. 86),
will change to .
•
Cannot be used with the self-timer (pp. 60, 80, 81).
•
Continuous shooting speed increases in
•
Depending on the shooting conditions, the camera settings and the zoom position, the camera may stop shooting momentarily, or the shooting speed may slow down.
•
As the number of images increases, the shooting speed may slow down.
•
If the flash fires, the shooting speed may slow down.
Changing the Tone of an Image (My Colors)
You can change the tone of an image to sepia or black and white when shooting.
Choose My Colors.
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
Choose an option.
●
Press the op buttons or turn the  dial to choose an option, then press the m button.
Vivid
My Colors Off
X
The setting will appear on the screen.
Y
—
Emphasizes the contrast and color saturation for a vivid
Tones down the contrast and color saturation for neutral impression.
Neutral
Sepia
B/W
Positive Film
Lighter Skin Tone hues.
Sepia tones.
COP
Blue to produce intense natural appearing colors like those obtained with positive film.
Makes skin tones lighter.
Darker Skin Tone
Vivid Blue
Vivid Green
Vivid Red
Makes skin tones darker.
Emphasizes blue tints. Makes the sky, ocean and other blue subjects more vivid.
Emphasizes green tints. Makes mountains, foliage and other green subjects more vivid.
Emphasizes red tints. Makes red subjects more vivid.
You can adjust contrast, sharpness, and color saturation
etc. to your preference (p. 80).
Custom Color
•
The white balance cannot be set in the and
•
In and modes, colors other than people’s skin color may change.
You may not obtain the expected results with some skin colors.
79
80
Using the Self-Timer to Prevent Camera Shake
Custom Color
The contrast, sharpness, color saturation, red, green, blue, and skin tones in an image can be chosen and set at 5 different levels.
●
Follow Step 2 on p. 79 to choose
, then press the n button.
●
Press the op buttons to choose an option, then press the qr buttons or turn the
 dial to choose a value.
●
The more to the right, the stronger/darker
(skin tone) the effect gets, the more to the
● left, the weaker/lighter (skin tone) the effect gets.
Press the setting.
Y
The camera will shoot approximately two seconds after the shutter button is pressed, preventing any camera shake that occurs when pressing the shutter button.
Using the Self-Timer to Prevent Camera Shake
COP
Choose
Î.
●
After pressing the o button, press the op buttons or turn the  dial to choose
Î, then press the m button.
X Once set,
Î will appear on the screen.
●
Follow Step 3 on p. 60 to shoot.
Customizing the Self-Timer
You can set the time delay (0 – 30 seconds) and the number of shots (1 – 10 shots).
Choose
$.
●
After pressing the o button, press the op buttons or turn the  dial to choose
$, then press the n button immediately.
Choose the settings.
●
Press the op buttons to choose [Delay] or [Shots].
●
Press the qr buttons or turn the  dial to choose a value, then press the m button.
●
Y
•
What if the number of shots is set to two or more shots?
•
Exposure and white balance settings are set with the first shot.
If the flash fires or you set a high number of shots, the shooting interval may take longer than usual.
COP
•
If the memory card becomes full, shooting stops automatically.
When you set the time delay for more than 2 seconds, the self-timer lamp and sound speed up 2 seconds before the shutter releases (when the flash will fire, the lamp lights).
81
82
Shooting Using a TV Monitor
You can use a TV to display the camera screen content while shooting.
•
To connect the camera to a TV, follow the Steps in “Viewing Images on a
•
Shooting procedures are the same as when using the camera screen.
TV display is not available when using HDMI Cable HTC-100 (sold separately) to connect the camera to a high-definition TV.
Changing the Composition with the
Focus Lock
While you keep the shutter button pressed halfway, the focus and exposure
Y
Focus.
●
Center the subject you want in focus, and
● press the shutter button halfway.
is green.
Recompose.
●
Keep the shutter button pressed halfway and move the camera to recompose the scene.
Shoot.
●
Press the shutter button fully.
5
Getting More Out of Your
Camera
This chapter serves as the advanced version of Chapter 4 and explains how to take pictures using various functions.
Y
COP
•
This chapter assumes that you have set the mode switch to
4 and set the camera to
G mode.
•
The sections “Changing the Color and Shooting” (p. 92), “Shooting Long
Exposures” (p. 95) and “Shooting Stitch Assist Images” (p. 96) assume
you have set the mode switch to
4 and chosen the corresponding mode.
•
Before attempting to shoot using a function explained in this chapter in modes other than
G mode, check if the function is available in those modes
83
84
Changing the AF Frame Mode
You can change the AF (Auto Focus) frame mode to match the scene you want to shoot.
Choose [AF Frame].
●
After pressing the n button, choose
[AF Frame] in the
4 tab, then press the qr buttons to choose an option.
Face Detect
•
Detects people’s faces and sets the focus, exposure (evaluative metering
•
only) and white balance ( only).
•
When the camera is pointed at subjects, a white frame appears on the face the camera judges to be the main subject, and gray frames (max. 2) will appear on other faces.
Y
•
When the shutter button is pressed halfway, up to 9 green frames will appear on faces that the camera focuses on.
•
shutter button halfway.
COP
•
The AF frame will appear in the center of the screen if you press the
shutter button halfway when Servo AF (p. 86) is set to [On] and a face is
not detected.
•
Examples of faces that cannot be detected:
• Subjects that are far away or extremely close.
• Subjects that are dark or light.
• Faces turned to the side or at a diagonal, or faces with a portion hidden.
•
The camera may mistakenly identify non-human subjects as a face.
•
If the camera cannot focus when you press the shutter button halfway, the AF frame will not appear.
Center
The AF frame is locked to the center. This is effective for focusing on a specific point.
Magnifying the Focal Point
You can reduce the AF frame size
•
Press the n button to choose [AF Frame Size] in the 4 tab, then choose
[Small].
•
The AF frame is set to [Normal] when using Digital Zoom (p. 57) or Digital Tele-
If the camera cannot focus when you press the shutter button halfway, the
AF frame will turn yellow and will appear.
Magnifying the Focal Point
check the focus.
If you press the shutter button halfway, the AF frame will magnify and you can
Y
●
Press the n button to choose [AF-
Point Zoom] in the
4 tab, then press the qr buttons to choose [On].
●
Press the shutter button halfway.
X
In [Face Detect] (p. 84), the face detected
as the main subject will appear magnified.
X
In [Center] (p. 84), the contents of the
center AF frame will appear magnified.
What if the display does not magnify?
The display will not appear magnified in [Face Detect] if a face cannot be detected or is too big in relation to the screen. In [Center], it will not appear magnified if the camera cannot focus.
The magnified display will not appear when using Digital Zoom (p. 57),
Digital Tele-converter (p. 58), Servo AF (p. 86) or when connected to a TV
85
86
Shooting with the AF Lock
The focus can be locked. After locking the focus, the focal distance will not change even when you release your finger from the shutter button.
Lock the focus.
●
Keep the shutter button pressed halfway and press the q button.
X
The focus locks and
% appears on the screen.
●
If you release your finger from the shutter button and press the q button again, % will disappear and the focus will unlock.
Compose the scene and shoot.
Y
Shooting with Servo AF
While the shutter button is pressed halfway, the focus and exposure will continue to adjust, allowing you to take pictures of moving subjects without missing a shot.
COP
Choose [Servo AF].
●
Press the n button to choose [Servo
AF] in the
4 tab, then press the qr buttons to choose [On].
Focus.
●
The focus and exposure will be maintained where the blue AF frame appears while you press the shutter button halfway.
Changing the Metering Method
•
The camera may not be able to focus in some conditions.
•
In low light conditions, AF frames may not turn blue even after pressing the shutter button halfway. In this case, you can set the focus and exposure with the AF frame setting.
•
If a correct exposure cannot be obtained, the shutter speed and aperture value appear in orange. Release your finger from the shutter button, then press it again halfway.
•
You cannot shoot with the AF lock in this mode.
•
The [AF-Point Zoom] option in the
4 tab is not available in Servo AF mode.
•
Not available when using Self-Timer (pp.60 , 80, 81).
Changing the Metering Method
match the shooting conditions.
COP
Y
Choose the metering method.
●
After pressing the m button, press the op buttons or turn the  dial to choose m button again.
Choose an option.
●
Press the op buttons or turn the  dial to choose an option, then press the m button.
X
The setting will appear on the screen.
Evaluative
Center
Weighted Avg.
Spot
Suitable for standard shooting conditions, including back lit shots.
Automatically adjusts the exposure to match the shooting conditions.
Averages the light metered from the entire frame, but gives greater weight to the center.
Only meters within the the center of the screen.
(Spot AE Point frame) that appears at
87
88
Shooting with the AE Lock
You can lock the exposure and shoot, or set the focus and exposure separately to shoot. AE stands for “Auto Exposure”.
Choose
Lock the exposure.
●
Point the camera toward the subject and press the o button while pressing the shutter button halfway.
X
When
& appears, the exposure will be locked.
●
If you release your finger from the shutter button and press the o button again, &
Y
Shooting with the FE Lock
the flash. FE stands for “Flash Exposure”.
Choose
Lock the flash exposure.
●
Point the camera toward the subject and press the o button while pressing the shutter button halfway.
X
The flash will fire and when
( appears, the flash output will be retained.
●
If you release your finger from the shutter button and press the o button again, ( will disappear and FE will unlock.
Compose the scene and shoot.
Shooting with Slow Synchro
You can make the main subject, such as people, appear bright by having the camera provide the appropriate illumination with the flash. At the same time, you can use a slow shutter speed to brighten the background that the light from the flash cannot reach.
Choose
….
●
After pressing the r button, press the qr buttons or turn the
 dial to choose …, then press the m button.
X Once set,
… will appear on the screen.
Shoot.
●
Even if the flash fires, ensure that the sound ends.
Y
Attach the camera to a tripod to prevent the camera from moving and blurring the image. Additionally, you should set the [IS Mode] to [Off] when
shooting with a tripod (p. 150).
COP
89
90
Correcting the Brightness and Shooting
(i-Contrast)
The camera can detect areas in the scene, such as faces or backgrounds, that are too bright or dark and automatically adjust them to the optimum brightness when shooting. Also, when the overall image is lacking in contrast, the camera will automatically correct the image for a sharper impression when shooting.
Choose [i-Contrast].
●
Press the n button and choose [i-
Contrast] in the
4 tab, then press the qr buttons to choose [Auto].
corrected properly.
X
Once set,
@ will appear on the screen.
Y
You can correct recorded images (p. 130).
flash.
COP
You can automatically correct red-eye that occurs in images taken with the
Choose [Flash Settings].
●
Press the n button to choose [Flash
Settings] in the
4 tab, then press the m button.
Adjust the setting.
●
Press the op buttons or turn the  dial to choose [Red-Eye Corr.], then press the qr buttons to choose [On].
X
Once set,
Πwill appear on the screen.
Checking for Shut Eyes
Red-eye correction may be applied to areas other than red eyes. For example, when red make-up has been used around eyes.
•
You can correct recorded images (p. 130).
•
You can also display the screen in Step 2 by pressing the r button, then the n button.
Checking for Shut Eyes
When the camera detects the possibility that people have their eyes shut, appears.
●
Press the
Y
[Blink Detection] in the
4 tab. Press the qr buttons to choose [On].
Shoot.
COP
appear.
•
In function is only available for the last image shot.
•
Not available in
W, , mode.
91
92
Changing the Color and Shooting
You can change the look of an image when shooting. However, depending on shooting conditions the image may become coarse, or the colors may not come out as expected.
Color Accent
You can choose to retain a single color and change the rest to black and white in a composition.
Recorded color
Choose
T.
●
Follow Steps 1 – 2 on p. 61 to choose
T.
Press the
n button for more
than one second.
X
Y
●
The color for default settings is green.
Specify the color.
●
Position the center frame so it is filled with
COP
Specify the range of colors.
q button.
●
Press the op buttons or turn the  dial to change the range of colors to be retained.
●
Choose a negative value to limit the range of colors. Choose a positive value to extend the range of colors to similar colors.
●
Pressing the n button accepts the setting and restores the shooting screen.
Using the flash may cause unexpected results in this mode.
Changing the Color and Shooting
Color Swap
You can swap one color in an image for another when recording it. You can only swap one color.
Choose
Y.
●
Follow Steps 1 – 2 on p. 61 to choose
Y.
Press the
n button for more
than one second.
X
The unchanged image and the Color Swap
●
Y gray.
Specify the color to be swapped.
●
Position the center frame so it is filled with
COP
Specify the target color.
q button.
●
Position the center frame so it is filled with the color you want and press the r button.
X
The specified color will be recorded.
93
94
Changing the Color and Shooting
Specify the range of colors to be swapped.
●
Press the op buttons or turn the  dial to adjust the range of colors to be changed.
●
Choose a negative value to limit the range of colors. Choose a positive value to extend the range of colors to similar colors.
●
Pressing the n button accepts the setting and restores the shooting screen.
•
Using the flash may cause unexpected results in this mode.
•
Under some conditions, the image may appear coarse.
Y
COP
Shooting Long Exposures
You can set the shutter speed to a range between 1 and 15 seconds to shoot long exposures. However, you should attach the camera to a tripod to prevent the camera from moving and blurring the image.
Choose
≈
.
●
Choose
Choose the shutter speed.
●
After pressing the m button, press the op buttons or turn the  dial to choose
●
, then press the m button again.
Press the
Y the m button.
Confirm the exposure.
COP shutter speed will appear on the screen.
•
The brightness of the image may differ from the brightness of the screen in Step 3 when the shutter button was pressed halfway.
•
When shutter speeds of 1.3 seconds or slower are used, images are processed to eliminate noise after being taken. A certain amount of processing time may be needed before you can take the next shot.
•
You should set the [IS Mode] to [Off] when shooting with a tripod
If the flash fires, the image may be overexposed. If this happens, set the flash to
!
and shoot.
95
96
Shooting Stitch Assist Images
Large subjects can be split into several shots that can later be merged together using the included software on a computer to create a panoramic image.
Choose
x or v.
●
Follow Steps 1 – 2 on p. 61 to choose
or v
.
x
Take the first shot.
X
The exposure and white balance will be set with the first shot.
●
Overlap part of the first shot when taking the second shot.
●
Minor discrepancies in the overlapping
● portions will be corrected when the images are merged.
COP same procedures.
Finish shooting.
Y
●
Press the m button.
Merge the images on a computer.
●
For details on how to merge the images, refer to the Software Guide.
This function is not available when a TV is used as the monitor (p. 82).
6
Using Various Functions for
Shooting Movies
This chapter serves as a more advanced version of the “Shooting
Y
COP
•
This chapter assumes that the mode switch is set to
E.
•
The latter half of the chapter explaining movie playback and editing assumes that the
1 button has been pressed to enter Playback mode.
Shooting Movies in Modes Other than
E
•
When the mode switch is set to
A, the camera can automatically select
all settings so that you can shoot movies (p. 30).
•
You can shoot movies by pressing the movie button, however, certain settings made in the
ø and Shooting menus will automatically change to match settings for shooting movies.
•
When you finish shooting a movie, the settings will return to those before the movie was shot.
97
98
Shooting Movies in E Mode
Enter
E mode.
●
Set the mode switch to
E.
Adjust the settings according to
your purposes (pp. 98 – 103).
Shoot.
●
Press the movie button.
●
To stop shooting the movie, press the movie button again.
Changing the Movie Mode
You can choose between five Movie modes.
COP
Normal mode.
Y
●
After pressing the m button, press the op buttons or turn the  dial to choose
E, then press the m button again.
●
Press the op buttons or turn the  dial to choose a mode, then press the m button.
E Standard
Captures fleeting moments at high-speed for playback in slow
Super Slow Motion
Miniature Effect
You can shoot movies that look like a miniature model (p. 99).
>
Color Accent
These Shooting modes let you change all colors except the chosen color to black and white, or exchange the chosen color for another color, when shooting. See “Changing the Color and
Shooting” (p. 92) for details. Choose the color you wish to leave
in or change before shooting the movie.
z
Color Swap
Under some conditions, colors may not turn out as expected in
> and z modes.
•
Pressing the movie button in mode will record a movie in
E.
•
Even if you press the movie button when in
T or Y, you can shoot
movies with Color Accent (p. 92) or Color Swap (p. 93).
Shooting Super Slow Motion Movies
You can shoot fast moving subjects and play them back in slow motion. The maximum clip length you can record is approximately 30 seconds long, which will take approximately 4 minutes to play back in slow motion.
Choose .
●
Follow the steps for "Changing the Movie
.
Shoot.
●
Press the movie button.
●
To stop shooting the movie, press the movie button again.
Viewing Super Slow Motion Movies
Y
•
The movie will play back in slow motion when you following Steps 1 – 3 on p. 32.
•
You can use the included software to change the playback speed of movies shot in . Refer to the Software Guide for details.
•
Even if you press the zoom lever, the zoom will not operate while
•
shooting.
The focus, exposure and white balance will be set when the movie button is pressed
COP
Shoot Movies That Look Like a Miniature
Model (Miniature Effect)
You can shoot movies that look like moving miniature models.
You create the miniature model effect by choosing the upper and lower portions of the scene that will be blurred and the playback speed, which makes people and objects in the scene move quickly during playback.
Audio will not be recorded.
Choose .
●
Follow the steps for "Changing the Movie
.
99
100
Shoot Movies That Look Like a Miniature Model (Miniature Effect)
X A white frame (the area that will not be blurred) appears on the screen.
Choose the area to keep in focus.
●
Press the n button for more than one second.
●
Move the zoom lever to change the frame size, and press the op buttons to change the frame position.
Choose a playback speed.
●
Press the m button.
●
Press the qr buttons or turn the  dial to choose a playback speed.
●
Pressing the n button restores the settings screen.
Y
Shoot.
●
Press the movie button.
●
To stop shooting the movie, press the movie button again.
Speed Playback Time
12 sec.
6 sec.
3 sec.
•
For the screen in Step 2, pressing the qr buttons will allow you to change the frame vertical orientation and also change the area to focus in. Pressing the op buttons will return the frame to horizontal orientation.
•
Holding the camera vertically will change the orientation of the frame.
•
Since you may not achieve the expected results depending on the shooting conditions, try taking some test shots first.
Changing the Movie Quality
You can choose between four movie quality settings.
Choose the movie quality setting.
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
Choose an option.
●
Press the op buttons or turn the  dial to choose an option, then press the m button.
X
The option you set will appear on the screen.
Movie Quality Table
Movie Quality
(Recording Pixels/Frame Rate)
Y
Content
1920 x 1080 pixels, 24 frames/sec. For shooting full high-definition movies.
1280 x 720 pixels, 30 frames/sec. For shooting high-definition movies.
640 x 480 pixels, 30 frames/sec. For shooting standard quality movies.
COP
Estimated Shooting Time
Since the number of recording pixels is smaller than
, the movie quality will appear coarse, but you can record approximately three times the length.
Shooting Time
Movie Quality
4 GB
14 min. 34 sec.
16 GB
59 min. 40 sec.
20 min. 43 sec.
43 min. 43 sec.
1 hr. 58 min. 19 sec.
1 hr. 24 min. 54 sec.
2 hrs. 59 min. 3 sec.
8 hrs. 4 min. 30 sec.
• Based on Canon’s testing standards.
• Recording will automatically stop when the clip file size reaches 4 GB, or when the recording time reaches approximately 10 minutes when shooting in or , and approximately 1 hour when shooting in or .
• Recording may stop even if the maximum clip length has not been reached on some memory cards. SD Speed Class 6 or higher memory cards are recommended.
101
102
AE Lock/Exposure Shift
You can lock the exposure or change it in 1/3 steps within a range of ±2 before shooting.
Focus.
●
Press the shutter button halfway to focus.
Lock the exposure.
●
After releasing the shutter button, press the r button to lock the exposure. The exposure shift bar appears.
●
Press the r button again to release the lock.
●
While watching the screen, turn the
 dial to adjust the exposure.
Shoot.
COP
Y
●
Press the movie button.
●
To stop shooting the movie, press the movie button again.
Other Shooting Functions
The following functions can be used in the same way as for still images.
Functions marked with a * can be used in the same way as for still images when in , ,
> or z.
• Zooming in More Closely On Subjects
- The optical and digital zooms (p. 57) are available in
E.
- Only the optical zoom is available in
>
and z
.
- Neither the optical nor digital zooms are available while shooting in .
Be sure to set the optical zoom before shooting.
- The sound of the zoom will be recorded.
•
•
Changing the Focusing Range (Macro/Infinity) (p.73)
Neither macro nor infinity shooting are available in .
•
Adjusting the White Balance (p.77)
•
Changing the Tone of an Image (My Colors) (p.79)
•
•
Customizing the Self-Timer (p.81)
Y
The number of shots cannot be changed.
•
Shooting Using a TV Monitor (p.82)*
•
Shooting with the AF Lock (p.86)
•
Turning Off the AF Assist Beam (p.147)*
•
•
Changing the IS-Mode Settings (p.150)*
You can switch between [Continuous] and [Off].
103
104
Playback Functions
The following functions can be used in the same way as for still images.
•
•
Quickly Searching Images (p.108)
•
Viewing Images in Filtered Playback (p.109)
•
•
Changing Image Transitions (p.114)
•
Viewing Images on a TV (p.115)
•
Viewing Images on a High-Definition TV (p.116)
•
•
•
Tagging Images as Favorites (p.122)
•
•
Organizing Images by Category (My Category) (p.123)
Y
(p. 32)
Exit
Playback speed. Sound will not play back.)
Display the first frame
Previous frame (Rewind if you hold down the m button.)
Next frame (Fast forward if you hold down the m button.)
Display the last frame
*
Appears when connected to a PictBridge compliant printer (p. 134).
Refer to the Personal Printing Guide for details.
Editing
You can trim the beginnings and ends of recorded movies.
Choose
*.
●
Follow Steps 1 – 3 on p. 32 to choose
*, then press the m button.
X
The movie editing panel and the movie editing bar will appear.
Movie Editing Panel
Set the editing range.
●
Press the op buttons and choose
or
.
Movie Editing Bar
●
Press the qr buttons or turn the  dial to move . will display at a point where
Y
, from . If you choose , you can trim the end of the movie from .
X
Even if you move to a point other than a
COP
to
is chosen.
Only the portion from the nearest to the right will be trimmed when is chosen.
X
The section indicated with will be the section of the movie that remains after editing.
105
106
Editing
Check the edited movie.
●
Press the op buttons to choose
(Play), then press the m button. The edited movie will play.
●
To edit the movie again, repeat Step 2.
●
To cancel editing, press the op buttons, and choose . After pressing the m button, press the qr buttons or turn the
 dial to choose [OK], then press the m button again.
Save the edited movie.
●
Press the op buttons to choose press the m button.
Y
, then
●
Press the opqr buttons, or turn the  dial to choose [New File], then press the m
•
button.
X
The movie will be saved as a new file.
COP with the edited movie, erasing the original.
•
When there is not enough space left on the memory card, only
[Overwrite] can be chosen.
•
If the battery is depleted partway through editing, the edited movie clips may not be saved.
•
When editing movies, you should use a fully charged battery, or an AC
adapter kit (sold separately) (p. 39).
7
Using Various Playback and
Editing Functions
•
This chapter explains various ways to play back and edit images.
Press the
Y
•
It may not be possible to play back or edit images that have been edited
•
on a computer, had their file name changed, or have been taken on a different camera.
107
Quickly Searching Images
Searching Images Using Index Display
Displaying multiple images at the same time lets you quickly find the image you want.
Move the zoom lever toward
g.
X
Images will display in an index.
●
The number of images increases each time you move the lever toward g.
●
The number of images decreases each time you move the lever toward k.
Choose an image.
●
●
X
Turn the
Press the
Y
An orange frame appears on the chosen image.
●
Press the m button to display the chosen image by itself.
Turning the control dial will display images in a line letting you quickly search them. You can also jump by the shooting date (Scroll Display).
Choose an image.
●
If you set the camera to single image playback and turn the
 dial quickly, the images will display as shown on the left.
Turn the
 dial to choose an image.
●
Pressing the m button restores single image playback.
●
If you press the op buttons during Scroll
Display, you can search images by the shooting date.
To turn off this effect, press the n button to choose [Scroll Display] in the
1 tab, then choose [Off].
108
Viewing Images in Filtered Playback
When there are many images on the memory card, you can filter and display
them by a specified filter. You can also protect (p. 117) or delete (p. 120) all
images at once while filtered.
Choose
‚
.
●
After pressing the m button, press the op buttons or turn the  dial to choose
‚, then press the m button again.
Choose a filter.
●
Press the op buttons or turn the  dial to choose a filter, then press the m button.
Y
●
Press the op buttons or turn the  dial to choose a filter for playback, then press
● the m button (except for
).
X
Filtered playback starts and a yellow frame
COP qr buttons or turn the  dial, only the chosen target images will display.
●
If you choose in Step 2, filtered playback will be canceled.
Search filters
Favorites
Shot Date
;
My Category
File Type
Displays images tagged as favorites (p. 122)
Displays the images shot on a specified date
Displays the images of a specified category (p. 123)
Displays only still images or movies
What if you can’t choose a filter?
Filters that do not have any corresponding images cannot be chosen.
109
Viewing Slideshows
Filtered playback
In filtered playback (Step 3), you can view filtered images with “Quickly Searching
Images” (p. 108), “Viewing Slideshows” (p. 110), and “Magnifying Images”
(p. 113). You can process all filtered images at once while performing operations
in “Protecting Images” (p. 117), “Erasing Images” (p. 120), or “Printing from the
Print List (DPOF)” (p. 137), by choosing all of the filtered images.
However, if you change the category (p. 123), or edit an image and save it as a
new image (p. 127), a message will appear, and filtered playback will cancel.
Viewing Slideshows
You can automatically play back images recorded to a memory card. Each image displays for approximately 3 seconds.
Choose
..
Y
●
After pressing the m button, press the op buttons or turn the  dial to choose
., then press the m button again.
110
●
Press the op buttons or turn the  dial to choose an effect, then press the m button.
X
The slideshow will start a few seconds after
[Loading image...] appears.
●
In filtered playback (p. 109), only images
matching a filter play back.
●
You can pause/restart a slideshow by pressing the m button again.
●
Press the n button to stop the slideshow.
•
If you press the qr buttons or turn the  dial during playback, the image will switch. If you keep the qr buttons pressed, you can fastforward through images.
•
The power saving function (p. 51) does not work during slideshows.
Viewing Slideshows
Changing Settings
You can set a slideshow to repeat, or change transition effects and the time that slideshow images are displayed. You can choose from six transition effects when switching between images.
Choose [Slideshow].
●
Press the n button to choose
[Slideshow] from the
1 tab, then press the m button.
Make the setting.
●
Press the op buttons or turn the  dial to choose an item, then press the qr
●
Y m button, the slideshow starts with your settings.
●
Pressing the n button will restore the
COP
You cannot change [Play Time] if [Bubble] is chosen in [Effect].
111
112
Checking the Focus
You can magnify the area of a recorded image that was inside the AF Frame, or the area of a face that was detected, to check the focus.
Press the
p button to switch to the
focus check display (p. 44).
X
A white frame will appear where the AF frame or face was when the focus was set.
X
A gray frame will appear on a face detected during playback.
X
The area within the orange frame appears
●
X magnified.
Switch frames.
Y k once.
The screen shown to the left will appear.
●
Press the m button to move to a different frame when multiple frames appear.
COP
●
Use the zoom lever to change the display size, and the opqr buttons to change the display position while checking the focus.
●
Pressing the n button resets the display to Step 1.
Magnifying Images
Move the zoom lever toward
k.
●
The display will zoom in on the image. If you continue to hold the zoom lever, it will zoom in up to a maximum factor of 10x.
●
If you press the opqr buttons, you can move the location of the displayed area.
●
Move the zoom lever toward g to zoom out, or continue to hold it to return to single image playback.
●
If you turn the
 dial, you can switch
Approximate Location of
Displayed Area images while zoomed.
You can return to single image playback immediately by pressing the n button while the image is magnified.
Y
Displaying Various Images (Smart Shuffle)
COP letting you enjoy the playing back of images in an unexpected order.
This will work best if you take many shots of various scenes.
Choose .
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
X
Four images will appear as possibilities.
113
114
Changing Image Transitions
Choose an image.
●
Press the opqr buttons to choose the image you want to view next.
X
The chosen image will be displayed in the middle, and the next four possibilities will appear.
●
Pressing the m button will display the middle image at full size. Press the m button again to restore the original display.
You can also use the zoom lever in the
•
same way.
●
Pressing the n button restores single image playback.
Y
•
Only still images shot with this camera will play back in Smart Shuffle.
is not available in the following situations:
-
-
If there are less than 50 images taken with this camera on the memory card.
-
If you play back images not supported by Smart Shuffle.
COP
Changing Image Transitions
You can choose from three transition effects when switching between images in single image playback.
Choose [Transition].
●
Press the n button to choose
[Transition] in the
1 tab, then press the qr buttons to choose a transition effect.
Viewing Images on a TV
Using the supplied stereo AV cable (p. 2), you can connect the camera to a
TV to view images you have shot.
Turn off the camera and TV.
Connect the camera to the TV.
●
Open the camera’s terminal cover and fully insert the cable plug into the camera’s terminal.
Yellow
Yellow
White
Red
Red
White
●
Insert the cable plug fully into the video
Y
Turn on the TV and switch it to the input the cable is connected to.
●
Press the
1 button to turn on the camera.
X
The image will appear on the TV (nothing will appear on the screen of the camera).
●
After you finish, turn off the camera and
TV, and unplug the cable.
What if the images don’t display correctly on the TV?
Images will not display correctly if the camera’s video output setting (NTSC/PAL) does not match the TV system. Press the n button, choose the 3 tab and
[Video System] to switch to the correct video system.
115
116
Viewing Images on a High-Definition TV
Use the separately sold HDMI Cable HTC-100 to connect the camera to a high-definition TV for an enhanced viewing experience.
Turn off the camera and TV.
Connect the camera to the TV.
●
Open the camera’s terminal cover and fully insert the cable plug into the camera’s terminal.
●
Fully insert the cable plug into the TV’s
HDMI terminal.
Y
●
Follow Steps 3 and 4 on p. 115 to display
the images.
The supplied stereo A/V and interface cables and the separately sold
HDMI Cable HTC-100 cannot be plugged into the camera at the same time. Doing so could cause the camera to malfunction.
Operation sounds will not play when connected to a high-definition TV.
Protecting Images
You can protect important images so that they cannot be accidentally erased
with the camera (pp. 29, 120).
Protect the image.
●
After pressing the m button, press the op buttons or turn the  dial to choose
:, then press the m button again.
X
[Protected] will appear on the screen.
●
To unlock an image, follow the Step above to choose
: again, then press the m button.
If you format the memory card (pp. 23, 52), protected images will also be
erased.
erase an image, cancel protection settings first.
Y
Using the Menu
Choose [Protect].
COP button.
n button to choose
[Protect] in the
1 tab, then press the m
Choose a selection method.
●
Press the op buttons or turn the  dial to choose a selection method, then press the m button.
●
Pressing the n button will restore the menu screen.
Choosing Images Individually
Choose [Select].
●
Follow Step 2 above to choose [Select], then press the m button.
117
118
Protecting Images
Choose images.
●
Press the qr buttons or turn the  dial to choose an image, then press the m button.
X
will appear on the screen.
●
Pressing the m button again deselects the image and will disappear.
●
To choose additional images, repeat the above procedure.
Protect the image.
●
If you press the n button, a
● confirmation screen will appear.
Press the
Y choose [OK], then press the m button.
If you switch shooting modes or turn off the power before performing the operations in Step 3, images will not be protected.
Select Range
COP
Choose [Select Range].
●
Follow Step 2 on p. 117 to choose [Select
Range], then press the m button.
Choose a starting image.
●
Press the m button.
●
Press the qr buttons or turn the  dial to choose an image, then press the m button.
Protecting Images
Choose an ending image.
●
Press the r button to choose [Last image], then press the m button.
●
Press the qr buttons or turn the  dial to choose an image, then press the m button.
●
You cannot choose images before the first image.
Protect images.
●
Press the p button to choose [Protect], then press the
Y
Choose images with the
 dial
You can also choose the first or last image by turning the
 dial when the upper
COP
Choose All Images
Choose [All Images].
●
Follow Step 2 on p. 117 to choose [All
Images], then press the m button.
Protect images.
●
Press the op buttons or turn the  dial to choose [Protect], then press the m button.
You can unlock groups of protected images if you choose [Unlock] in Step
4, while in [Select Range] or Step 2 while in [All Images].
119
Erasing Images
You can choose images and then erase them in groups. Since erased images cannot be recovered, exercise adequate caution before erasing. Protected
images (p. 117) cannot be erased.
Choose a selection method
Choose [Erase].
●
Press the n button to choose [Erase] in the
1 tab, then press the m button.
120
Choose a selection method.
●
Press the op buttons or turn the  dial
● to choose a selection method, then press the m button.
Pressing the
Y menu screen.
Choosing Images Individually
COP and press the m button.
Choose an image.
X
If you follow Step 2 on p. 118 to choose
images, will appear on the screen.
●
Pressing the m button again deselects the image and will disappear.
●
To choose additional images, repeat the above procedure.
Erase.
●
If you press the n button, a confirmation screen will appear.
●
Press the qr buttons or turn the  dial to choose [OK], then press the m button.
Erasing Images
Select Range
Choose [Select Range].
●
Follow Step 2 on p. 120 to choose [Select
Range], then press the m button.
Choose images.
●
Follow Steps 2 and 3 on p. 118 to choose
images.
Erase.
Choose All Images
●
Press the p button to choose [Erase], then press the m button.
Y
Choose [All Images].
●
Follow Step 2 on p. 120 to choose [All
COP
Erase.
m button.
●
Press the qr buttons or turn the  dial to choose [OK], then press the m button.
121
122
Tagging Images as Favorites
When you tag images as favorites, you can easily categorize just those images. You can also filter out just those images for viewing, protecting or
Make the setting.
●
After pressing the m button, press the op buttons or turn the  dial to choose
, then press the m button again.
X
[Tagged as favorites] will appear on the screen.
Using the Menu
●
To untag the image, follow the above Step to choose again, then press the m button.
Y
●
Press the n button to choose
[Favorites] in the
1 tab, then press the m button.
COP
●
Press the qr buttons or turn the  dial to choose an image, then press the m button.
X
will appear on the screen.
●
Pressing the m button again untags the image and disappears.
●
To choose additional images, repeat the above procedure.
Make the setting.
●
If you press the n button, a confirmation screen will appear.
●
Press the qr buttons or turn the  dial to choose [OK], then press the m button.
Organizing Images by Category (My Category)
If you switch Shooting modes or turn off the power before making the setting in Step 3, images will not be tagged as favorites.
If you use Windows 7 or Windows Vista and transfer tagged images to the computer, they will be given a star rating of 3 ( movies).
) (except for
Organizing Images by Category
(My Category)
You can organize images into categories. You can display the images in a
category in Filtered Playback (p. 109) and process all images at once by
using the functions below.
•
Images are automatically categorized by shooting condition as they are shot.
: Images with detected faces, or images shot in
I or V mode.
: Images detected as
or
O mode.
: Images shot in
, or
COP
Choose
;
.
in
A mode, or images shot in
●
After pressing the m button, press the op buttons or turn the  dial to choose
;, then press the m button again.
Choose a category.
●
Press the op buttons to choose a category, then press the m button.
X
will appear on the screen.
●
Pressing the m button again deselects the image and will disappear.
123
Organizing Images by Category (My Category)
Make the setting.
●
If you press the n button, a confirmation screen will appear.
●
Press the qr buttons or turn the  dial to choose [OK], then press the m button.
If you switch Shooting modes or turn off the power before making the setting in
Step 3, images will not be tagged as My Category.
Using the Menu
Choose [My Category].
●
Press the n button to choose [My
Category] in the
1 tab, then press the m button.
Y
Choose a selection method.
●
Press the op buttons or turn the  dial to choose a selection method, then press
●
Pressing the n button will restore the menu screen.
Choosing Images Individually
Choose [Select].
●
Follow Step 2 above to choose [Select], then press the m button.
Choose an image.
●
Press the qr buttons or turn the  dial to choose an image.
Choose a category.
●
Press the op buttons, or turn the  dial to choose a category, then press the m button.
124
Organizing Images by Category (My Category)
X will appear on the screen.
●
Pressing the m button again deselects the image and will disappear.
●
To choose additional images, repeat the above procedure.
Make the setting.
●
If you press the n button, a confirmation screen will appear.
●
Press the qr buttons or turn the  dial to choose [OK], then press the m button.
If you switch Shooting modes or turn off the power before making the setting in
Step 4, images will not be tagged as My Category.
Select Range
Y
Choose [Select Range].
●
Follow Step 2 on p. 124 to choose [Select
COP
●
Follow Steps 2 and 3 on p. 118 to choose
images.
m button.
Choose a category.
●
Press the p button to choose an item, then press the qr buttons or turn the  dial to choose a category.
Choose the setting.
●
Press the p button to choose [Select], then press the m button.
If you choose [Deselect] in Step 4, you can deselect all of the images in the [Select Range] category.
125
126
Rotating Images
You can change the orientation of an image and save it.
Using the Menu
Choose
\
.
●
After pressing the m button, press the op buttons or turn the  dial to choose
\, then press the m button again.
Rotate the image.
●
Press the qr buttons to rotate the image
90° in the chosen direction.
●
Press the m button to make the setting.
Choose [Rotate].
Y
●
Press the n button to choose [Rotate] in the
1 tab, then press the m button.
●
Press the qr buttons or turn the  dial to choose an image.
X
The image will rotate 90° with each press of the m button.
●
Pressing the n button will restore the menu screen.
Movies with a resolution of or cannot be rotated.
Resizing Images
You can resize images to a lower pixel setting and save the resized image as a separate file.
Choose [Resize].
●
Press the n button to choose
[Resize] in the
1 tab, then press the m button.
Choose an image.
●
Press the qr buttons or turn the  dial to choose an image, then press the m button.
●
Press the
Y choose an option, then press the m button.
X The [Save new image?] screen will appear.
COP qr buttons or turn the  dial to choose [OK] and press the m button.
X
The image will be saved as a new file.
Display the new image.
●
When you press the n button, the
[Display new image?] screen will appear.
●
Press the qr buttons or turn the  dial to choose [Yes], then press the m button.
X
The saved image will be displayed.
•
You cannot resize an image to a larger size.
•
Images recorded at a pixel setting of
in Step
3 cannot be edited.
127
128
Trimming
You can cut out a portion of a recorded image and save it as a new image file.
Choose [Trimming].
●
Press the n button to choose
[Trimming] in the
1 tab, then press the m button.
Choose an image.
●
Press the qr buttons or turn the  dial to choose an image, then press the m button.
Trimming Area
Adjust the trimming area.
X
A frame will appear around the portion of
X
Y left and the trimmed image will display in
Trimming Area Display
Recorded pixels after trimming
● the lower right.
●
If you move the zoom lever to the left or
COP opqr buttons, you can move the frame.
●
If you press the m button, you can change the frame orientation.
●
In an image with detected faces, gray frames appear around the faces located in the upper left image. The frames can be used for trimming. You can switch between frames by turning the
 dial.
●
Press the n button.
Save as a new image and display.
●
Follow Steps 4 and 5 on p. 127.
Adding Effects with the My Colors Function
•
Images recorded at a pixel setting of or
resized to
•
The width and height ratio of an image that can be trimmed is fixed at 4:3.
•
The number of recorded pixels in a trimmed image will be smaller than before trimming.
Adding Effects with the My Colors Function
You can change the color of an image and save it as a separate image. Refer
to p. 79 for details on each menu item.
Choose [My Colors].
●
Press the n button to choose [My
Colors] in the
1 tab, then press the m button.
Y
Choose an image.
●
Press the qr buttons or turn the  dial to choose an image, then press the m
Choose a menu option.
●
Press the qr buttons or turn the  dial to choose an option, then press the m button.
Save as a new image and display.
●
Follow Steps 4 and 5 on p. 127.
If you repeatedly change the color of the same image, the quality will gradually deteriorate and you may not achieve the expected color.
The color of images changed with this function may vary from those
recorded with the My Colors function (p. 79).
129
Correcting the Brightness (i-Contrast)
The camera can detect areas in an image, such as faces or backgrounds, that are too dark and automatically adjust them to the optimum brightness. Also, when the overall image is lacking in contrast, the camera will automatically correct the image for a sharper impression. You can choose from four levels of correction, and save the image as a new file.
Choose [i-Contrast].
●
Press the n button to choose [i-
Contrast] in the
1 tab, then press the m button.
Choose an image.
●
Press the qr buttons or turn the  dial to choose an image, then press the m button.
Y
Choose a menu item.
●
Press the qr buttons or turn the  dial to choose an option, then press the m
Save as a new image and display.
●
Follow Steps 4 and 5 on p. 127.
•
Under some conditions, the image may appear coarse or not be corrected properly.
•
Repeatedly adjusting the same image may cause it to become coarse.
What if the image wasn’t corrected by the [Auto] option as well as you would like?
Choose [Low], [Medium] or [High] and adjust the image.
130
Correcting the Red-Eye Effect
You can automatically correct red eyes in images and save them as new files.
Choose [Red-Eye Correction].
●
Press the n button to choose [Red-
Eye Correction] in the
1 tab, then press the m button.
Choose an image.
●
Press the qr buttons or turn the  dial to choose an image.
Correct the image.
●
Press the m button.
X
Y the corrected portion.
●
You can magnify or reduce the size of the image using the procedures in “Magnifying
COP
●
Press the opqr buttons or turn the  dial to choose [New File], then press the m button.
X
The image will be saved as a new file.
●
•
Some images may not be corrected properly.
•
When [Overwrite] in Step 4 is chosen, the uncorrected image is overwritten with the corrected data, erasing the original image.
•
Protected images cannot be overwritten.
131
132
COP
Y
8
Printing
This chapter explains how to choose images for printing, and print
using a Canon-brand PictBridge compliant printer (sold separately)
Y
Canon-Brand PictBridge Compliant Printers
COP
133
134
Printing Images
You can easily print the pictures you take by connecting the camera to a
PictBridge compliant printer (sold separately) using the supplied interface
Turn off the camera and printer.
Connect the camera to the printer.
●
Open the cover and insert the small plug of
the included interface cable (p. 2) firmly
into the camera terminal in the direction shown.
●
Insert the interface cable’s larger plug into the printer. For connection details, refer to
Y
Turn on the camera.
●
Press the
1 button to turn on the camera.
Choose an image to print.
●
Press the qr buttons or turn the  dial to choose an image.
Printing Images
Choose
2.
●
After pressing the m button, press the op buttons or turn the  dial to choose
2, then press the m button again.
Print images.
●
Press the op buttons or turn the  dial to choose [Print], then press the m button.
X
Printing will start.
Y
●
If you want to print additional images, repeat Steps 5 to 7 after printing has completed.
●
After printing has completed, turn off the
COP
•
Refer to the Personal Printing Guide for details on printing.
•
Refer to p. 40 for Canon-brand Pictbridge compliant printers.
•
Index printing (p. 137) is not available on certain Canon-brand PictBridge
compliant printers (sold separately).
135
136
Printing from the Print List (DPOF)
You can add images to the print list (DPOF) directly after shooting or during playback in the
ø menu.
These selection methods comply with the DPOF (Digital Print Order Format) standards.
Choose an image.
●
Press the qr buttons or turn the  dial to choose an image.
Choose
c (movies will be
excluded).
●
After pressing the m button, press the op buttons or turn the  dial to choose
Y
●
Press the op buttons to choose the number of prints, then press the qr buttons or turn the
 dial to choose [Add]
COP m button.
●
To cancel adding images, repeat Steps 1 and 2, and press the qr buttons or turn the
 dial to choose [Remove], then press the m button.
You cannot add images when the camera is connected to the printer.
Choosing Images for Printing (DPOF)
You can choose up to 998 images on a memory card for printing and specify settings such as the number of copies so that they can be printed together
(p. 140) or processed at a photo developer service. These selection methods
comply with the DPOF (Digital Print Order Format) standards.
Print Settings
You can set the print type, date and file number. These settings apply to all images chosen for printing.
Print Type
Date
File No.
Clear DPOF data
On
Off
On
Off
On
Off
Choose [Print Settings].
Both
●
Press the n button to choose [Print
Settings] in the
2 tab, then press the m
● button.
Press the
Y to choose a menu item, then press the qr
Index buttons to choose an option.
●
Pressing the n button accepts the
COP
Standard Prints one image per page.
Prints several reduced size images per page.
Prints both standard and index formats.
Prints the shooting date.
—
Prints the file number.
—
Removes all print settings after printing.
—
•
Some printers or photo developer services may not be able to reflect all of the settings in the prints.
•
may appear when using a memory card with print settings set by a different camera. These settings will be overwritten with those set by your camera.
•
If [Date] is set to [On], some printers may print the date twice.
137
Choosing Images for Printing (DPOF)
138
•
With [Index] chosen, the [Date] and [File No.] options cannot be set to
[On] at the same time.
•
The date will be printed in the style set in the [Date/Time] function in the
•
Movies cannot be added to a print list.
Choosing the Number of Copies
Choose [Select Images & Qty.].
●
Press the n button to choose [Select
Images & Qty.] in the
2 tab, then press
● the m button.
Choose an image.
Press the
Y choose an image, then press the m
● button.
X
You will be able to set the number of print
COP appears on the screen. Pressing the m button again will deselect the image and
will disappear.
Set the number of prints.
●
Press the op buttons or turn the  dial to set the number of prints (maximum 99).
●
Repeat Steps 2 and 3 to choose other images and the number of prints for each.
●
You cannot set the number of copies for index prints. You can only choose which images to print (as shown in Step 2).
●
Pressing the n button accepts the settings and restores the menu screen.
Choosing Images for Printing (DPOF)
Select Range
Choose [Select Range].
●
In Step 1 on p. 138, choose [Select
Range], then press the m button.
●
Follow Steps 2 and 3 on p. 118 to choose
images.
Make print settings.
●
Press the op buttons to choose [Order], then press the m button.
Set All Images to Print Once
Y
Choose [Select All Images].
●
In Step 1 on p. 138, choose [Select All
Images], then press the m button.
●
Press the qr buttons or turn the  dial to choose [OK], then press the m button.
Clearing All Selections
Choose [Clear All Selections].
●
In Step 1 on p. 138, choose [Clear All
Selections], then press the m button.
All selections will be cleared.
●
Press the qr buttons or turn the  dial to choose [OK], then press the m button.
139
140
Print Added Images
You can print images added to the print list by connecting the camera to a
PictBridge compliant printer (pp. 136 – 139).
Number of copies to print
Connect the camera to the printer.
●
Follow Steps 1 to 4 on p. 134.
Print.
●
Press the op buttons to choose [Print now], then press the m button.
X
Printing will start.
●
If you stop the printer during printing and start again, it will start from the next print.
Y
COP
9
Customizing Camera Settings
You can customize various settings to suit your shooting preferences.
The first part of this chapter explains convenient and commonly used functions.
to suit your purposes.
Y
COP
141
142
Changing Camera Settings
You can customize convenient and commonly used functions from the
3 tab
Changing Sounds
You can change each of the camera’s operation sounds.
●
Choose [Sound Options], then press the m button.
●
Press the op buttons or turn the  dial to choose an option.
●
Press the qr buttons to choose an option.
1
2
Preset sounds (cannot be modified)
Preset sounds
Y
Turning Off Hints & Tips
When you choose an item in the
ø menu (p. 46) or MENU (p. 47), a
description of the function (hints and tips) is displayed. You can turn off this function.
●
Choose [Hints & Tips], then press the qr buttons to choose [Off].
Changing Camera Settings
Changing the Start-up Screen
You can change the start-up screen that appears when you turn on the camera.
●
Choose [Start-up Image], then press the m button.
●
Press the qr buttons or turn the  dial to choose an option.
No start-up image
Preset images (cannot be modified)
1
2
Registering Recorded Images as the Start-up
Screen
Preset images
You can set recorded images, and use the included software to change the images.
Y
When you press the
1 button and set the camera to Playback mode, you can register an image.
COP
●
Press the qr buttons or turn the  dial to choose [2], then press the m button.
●
Press the qr buttons or turn the  dial to choose an image, then press the m button.
●
Press the qr buttons or turn the  dial to choose [OK], then press the m button to complete registration.
Any previously registered start-up image will be overwritten when registering a new start-up image.
143
144
Changing Camera Settings
Register the start-up image or sounds with the included software
The dedicated operation sounds and start-up images on the included software can be registered to the camera. Refer to the Software Guide for details.
Changing the File Number Assignment
Images you shoot are automatically assigned file numbers in the order they were taken, from 0001 – 9999, and saved to folders of up to 2,000 images.
You can change the file number assignment.
●
Choose [File Numbering], then press the qr buttons to choose an option.
Continuous
Even if you shoot using a new memory card, the file numbers
Y is taken/saved.
If you replace the memory card
Auto Reset
COP with a new one, or a new folder is created, file numbering begins with 0001 again.
•
If you use a memory card already containing images, the newly assigned file numbers may continue the existing numbering for both [Continuous] and [Auto Reset]. If you want to start over with file number 0001, format
the memory card before use (p. 23).
•
Refer to the Software Guide for information regarding folder structure or image types.
Creating Folders by Shooting Date
Images are saved into folders created each month, however, you can also create folders by shooting date.
●
Choose [Create Folder], then press the qr buttons to choose [Daily].
●
Images will be saved into folders created on each shooting date.
Changing Camera Settings
Changing the Lens Retract Time
For safety reasons, the lens retracts about 1 minute after pressing the
1
button when in a Shooting mode (p. 28). If you want the lens to retract
immediately when you press the
1 button, set the retract time to [0 sec.].
●
Choose [Lens Retract], then press the qr buttons to choose [0 sec.].
Turning Off the Power Saving Function
You can set the power saving function (p. 51) to [Off]. Setting it to [On] is
recommended to save battery power.
button.
Y
●
Choose [Power Saving], then press the m
●
Press the op buttons or turn the  dial to
● choose [Auto Power Down], then press the
COP
If you set the power saving function to [Off], be sure to turn the camera off after use.
Setting the Screen Shut-Off Time
You can adjust the time the screen takes to shut off automatically (p. 51). This
also works when [Auto Power Down] is set to [Off].
●
Choose [Power Saving], then press the m button.
●
Press the op buttons or turn the  dial to choose [Display Off], then press the qr buttons to choose a time.
●
In order to save battery power, you should choose less than [1 min.].
145
146
Changing Camera Settings
Using the World Clock
When traveling abroad, you can record images with local dates and times simply by switching the time zone setting. If you pre-register the destination time zones, you can enjoy the convenience of not having to switch the Date/
Time settings.
Set the home time zone.
●
Choose [Time Zone], then press the m button.
●
When setting this for the first time, check
● the information that displays on the screen at the left, then press the m button.
Press the
Y
●
To set daylight saving time (adds 1 hour), press the op buttons to choose
.
●
Press the m button.
COP to choose [ World], then press the m button.
op buttons or turn the  dial
●
Press the qr buttons or turn the  dial to choose the destination time zone.
●
You can also set the daylight saving time as in Step 1.
●
Press the m button.
Choose the world time zone.
●
Press the op buttons or turn the  dial to choose , then press the n button.
X
will appear on the shooting screen
Changing Shooting Function Settings
If you change the date or time in the
Home] time and date will automatically change.
Changing Shooting Function Settings
If you set the mode switch to
4, and the mode to G, you can change the settings in the
Before attempting to shoot using a function explained in this chapter in modes other than
G mode, check if the function is available in those
Switching the Focus Setting
the shutter button is pressed halfway.
●
Choose [Continuous AF], then press the qr buttons to choose [Off].
COP
On
Since the camera focuses continuously until you press the shutter button halfway, it allows you to shoot without missing photo opportunities.
The camera does not focus continuously, thereby conserving battery power.
Off
Turning Off the AF Assist Beam
The lamp will automatically light to assist focusing in low light conditions when you press the shutter button halfway. You can turn off the lamp.
●
Choose [AF-assist Beam], then press the qr buttons to choose [Off].
147
148
Changing Shooting Function Settings
Turning Off the Red-Eye Reduction Function
The red-eye reduction lamp lights in order to reduce the red-eye effect that occurs when shooting in dark conditions with the flash. You can turn off this function.
●
Choose [Flash Settings], then press the m button.
●
Press the op buttons or turn the  dial to choose [Red-Eye Lamp], then press the qr buttons to choose [Off].
Changing the Image Display Time Right After
Shooting
Y
●
Choose [Review], then press the qr buttons to choose an option.
2 – 10 sec.
Displays images for the set time.
COP
The image displays until you press the shutter button halfway.
Off
Images will not display.
Changing Shooting Function Settings
Changing the Way the Image Displays Right After
Shooting
You can change the way the image displays right after shooting.
●
Choose [Review Info], then press the qr buttons to choose an option.
Displays the image only.
Off
Detailed
Displays detailed information
The area inside the AF frame is magnified, allowing you to check
Focus Check
Displaying the Overlay
the focus. The procedure is the same as in “Checking the Focus”
Y
You can display gridlines for vertical and horizontal guidance, or a 3:2 guide to confirm the printable area for postcard size prints.
COP qr
Grid Lines A grid overlays the screen.
Gray bars appear on the top
3:2 Guide and bottom of the screen. This area will not print when printing on paper with a 3:2 aspect ratio.
Both grid lines, and the 3:2 guide appear.
Both
•
In , you cannot set [3:2 Guide] or [Both].
•
Grid lines will not be recorded on the image.
•
The gray areas displayed with [3:2 Guide] are the areas that will not be printed. The actual image recorded will include the portion in the gray areas.
149
150
Changing Shooting Function Settings
Changing the IS-Mode Settings
●
Choose [IS Mode], then press the qr buttons to choose an option.
Continuous
Image stabilization is always on.
You can confirm the effects directly on the display, which makes it easier to check the composition or focus. When shooting movies, the camera also reduces strong camera shake, for example when walking (Dynamic mode).
Shoot Only*
Panning*
Image stabilization is only active at the moment of shooting.
Y objects moving horizontally.
* Setting changes to [Continuous] when shooting movies.
•
COP
•
When using [Panning], hold the camera horizontally to shoot. Image stabilization does not work when the camera is held vertically.
When shooting movies, if you press the zoom lever toward j and zoom out, the effect increases.
Changing Playback Function Settings
You can adjust the settings in the
1 tab by pressing the 1 button (p. 47).
Choosing the Image that First Displays in
Playback
●
Choose [Resume], then press the qr buttons to choose an option.
Last seen
Last shot
Resumes with the image last viewed.
Resumes with the most recently shot image.
COP
Y
151
152
COP
Y
10
Useful Information
This chapter introduces how to use the AC adapter kit and Eye-Fi card
(both sold separately), troubleshooting tips, and contains lists of functions and items that appear on the screen.
Y
COP
153
154
Using Household Power
If you use AC Adapter Kit ACK-DC70 (sold separately), you can use the camera without worrying about how much charge is left in the battery.
Terminals
Turn off the camera.
Insert the coupler.
●
Follow Step 1 on p. 17 to open the cover,
then insert the coupler as shown until it locks into place with a click.
●
Follow Step 3 on p. 17 to close the cover.
Plug the cord into the coupler.
● into the coupler.
Y
●
Connect the power cord to the compact power adapter, then plug the other end into a power outlet.
●
Turn the camera on to use it.
●
After you finish, turn off the camera and unplug the power cord from the power outlet.
Do not unplug the plug or power cord with the camera turned on. This could erase images you have taken or damage the camera.
Using an Eye-Fi Card
Before using an Eye-Fi card, be sure to check whether Eye-Fi card use is
authorized in the country or territory of use (p. 16).
When you put a prepared Eye-Fi card into the camera, you can automatically transfer your images wirelessly to a computer, or upload them to a web service.
Image transfer is a function of the Eye-Fi card. For details on how to setup and use the card, and concerning problems transferring images, please refer to the Eye-Fi card user guide, or contact the manufacturer.
Please keep the following things in mind when using an Eye-Fi card.
•
Even if you set [Eye-Fi trans.] to [Disable] (p. 156), the Eye-Fi card may
transmit radio waves. Be sure to remove the Eye-Fi card from the camera before entering areas that prevent unauthorized transmission of radio waves,
• such as hospitals and airplanes.
• If you have trouble transferring images, check the card or computer settings.
Y
• Due to its transfer function, the Eye-Fi card may become hot.
• Battery consumption will be quicker than in normal use.
• Camera operations will be slower than in normal use. This may be resolved by setting [Eye-Fi trans.] to [Disable].
COP checked in the shooting screen (Information Display) and playback screen
(Simple Information Display).
(Gray) Not connected
(Flashing white) Connecting
(White)
(Animated)
Transfer standby
Transferring
Interrupted
Error retrieving Eye-Fi card info (Turn the camera off and on again.
If this continues to appear, there may be a problem with the card.)
will appear on transferred images.
The power saving function does not work while transferring images (p. 51).
155
156
Using an Eye-Fi Card
Checking Connection Information
You can check the Eye-Fi card’s access point SSID, or connection status.
Choose [Connection info].
●
Press the n button, then choose
[Eye-Fi Settings] from the
3 tab, and press the m button.
●
Press the op buttons or turn the  dial to choose [Connection info], then press the m button.
X
The Connection info screen will appear.
Disabling Eye-Fi Transfer
You can set the card to disable Eye-Fi transfer.
Y
Choose [Disable] in [Eye-Fi trans.].
●
Press the n button to choose [Eye-Fi
Settings] from the
3 tab, then press the
●
Press the op buttons or turn the  dial to choose [Eye-Fi trans.], then press the qr buttons to choose [Disable].
What if [Eye-Fi Settings] does not appear?
[Eye-Fi Settings] will only appear when an Eye-Fi card is inserted in the camera.
If the Eye-Fi card has a write-protect tab, you will not be able to check the card's connection status, or set [Eye-Fi trans.] to [Disable] when the tab is in the locked position.
Troubleshooting
If you think there is a problem with the camera, first check the following. If the items below do not solve your problem, contact a Canon Customer Support
Help Desk as listed on the included customer support list.
Power
You pressed the power button, but nothing happened.
•
Confirm that the battery is the correct type, and is not depleted (p. 15).
•
Confirm that the battery is properly inserted (p. 17).
•
Confirm that the memory card/battery cover is securely closed (pp. 17, 18).
•
If the battery terminals are dirty, battery performance will decrease. Clean the terminals with a cotton swab and re-insert the battery several times.
Battery is consumed quickly.
•
Battery performance decreases at low temperatures. Warm the battery, for example,
•
by placing it in your pocket with the terminal cover on.
Lens will not retract.
Y
TV output
•
Image is distorted or not showing on TV (p. 115).
Shooting
Cannot shoot.
COP
Screen does not display properly in dark places (p. 45).
Screen does not display properly while shooting.
Please note, the following will not be recorded in still images, but will be recorded in movies.
•
When the camera is subjected to powerful light sources, the display may darken.
•
When shooting under fluorescent or LED lighting, the screen may flicker or horizontal lines may appear across the screen.
•
When shooting bright light sources, a bar of light (purplish red) may appear on the screen.
A flashing
h appears on the screen and the shot cannot be taken even
though the shutter button was pressed fully (p. 27).
appears when the shutter button is pressed halfway (p. 56).
•
Set the [IS mode] to [Continuous] (p. 150).
•
Set the flash to
•
Increase the ISO speed (p. 76).
•
Attach the camera to a tripod. Additionally, you should set the [IS Mode] to [Off] when
shooting with a tripod (p. 150).
157
Troubleshooting
158
Image is blurred.
•
Press the shutter button halfway to focus on the subject, then press fully to shoot
•
Shoot the subject within the focusing distance (p. 172).
•
Set the [AF-assist Beam] to [On] (p. 147).
•
Confirm that functions which you do not intend to use (macro, etc.) are not set.
•
Shoot using the focus lock or AF lock (pp. 82, 86).
Even when you press the shutter button halfway, the AF frame does not appear, and the camera does not focus.
•
If you center on the light and dark contrasting area of the subject and push the shutter button halfway, or repeatedly push the shutter button halfway, the AF frame will appear and the camera will focus.
Subject is too dark.
•
Set the flash to
•
Correct the brightness with exposure compensation (p. 72).
•
Adjust the image with i-Contrast (pp. 90, 130).
•
Use AE Lock, or spot metering to shoot (pp. 87, 88).
Y
Subject is too bright (overexposed).
•
Set the flash to
•
•
Correct the brightness with exposure compensation (p. 72).
•
Use AE Lock, or spot metering to shoot (pp. 87, 88).
COP
•
Shoot within an appropriate distance for flash photography (p. 73).
•
Increase the ISO speed (p. 76).
Image taken using the flash is too bright (overexposed).
•
Shoot within an appropriate distance for flash photography (p. 73).
•
Set the flash to
White dots appear on the image when shooting with the flash.
•
Light from the flash has reflected off dust particles or other objects in the air.
Image appears rough or grainy.
•
Shoot with the ISO speed on a lower setting (p. 76).
•
Depending on the Shooting mode, when shooting in a high ISO speed the image may
appear rough or grainy (pp. 62, 63).
•
Set the [Red-Eye Lamp] to [On] (p. 148). When shooting with the flash, the lamp (on
the front of the camera) lights (p. 42), and for approximately 1 second while the camera
is reducing red-eye, it is not possible to shoot. It is more effective if the subject is looking directly at the lamp. Even better results can be obtained by increasing the lighting in indoor settings or approaching closer to the subject.
Troubleshooting
Recording images to the memory card takes a long time, or continuous shooting slows down.
•
Perform a low-level format of the memory card in the camera (p. 52).
Cannot make settings for shooting functions or
ø menu.
•
The items in which settings can be made differ depending on the shooting mode. Refer
to “Functions Available in Each Shooting Mode” and “Shooting Menu” (pp. 166 – 169).
Shooting movies
Correct shooting time does not display, or stops.
•
Format the memory card in the camera, or use a memory card capable of recording at high speeds. Even when the shooting time does not display properly, the recorded
video will be the length that it was actually shot (pp. 23, 31).
appeared on the screen and shooting ended automatically.
•
The camera’s internal memory was insufficient. Try one of the following:
•
Perform a low-level format of the memory card in the camera (p. 52).
•
Change the movie quality setting (p. 101).
Subject appears distorted.
Y
•
The subject may appear distorted if it passes quickly in front of the camera while shooting. This is not a malfunction.
•
Playback
Cannot play back images or movies.
COP
Playback stops, or audio cuts out.
•
Use a memory card that has had a low-level format performed on it with this camera
•
If you copy a movie to a memory card that reads slowly, playback may interrupt momentarily.
•
Depending on its capabilities, when playing movies on a computer, frames may drop or the audio may cut out.
Computer
Cannot transfer images to a computer.
It may be possible to solve the problem when the camera is connected to a computer via cable by reducing the transfer speed.
•
Press the
1 button to enter Playback mode. Then press and hold the n button and press the o and m buttons together. In the screen that appears, press the qr buttons to choose [B] and press the m button.
Eye-Fi Card
Cannot transfer images (p. 155).
159
160
List of Messages That Appear on the Screen
If error messages appear on the screen, try one of the following solutions.
No memory card
•
The memory card is not installed in the correct direction. Install the memory card in the
Memory card locked
•
The SD memory card, SDHC memory card, SDXC memory card or Eye-Fi card’s write
protect tab is set to “LOCK”. Unlock the write protect tab (pp. 18, 19).
Cannot record!
•
You attempted to shoot an image without a memory card. Install the memory card in
the correct direction to shoot (p. 18).
•
If the same message appears even when a formatted memory card is installed in the
correct direction, contact a Canon Customer Support Help Desk (p. 18).
Insufficient space on card
•
There is not enough free space on the memory card to shoot (pp. 25, 30, 55, 71, 98)
or edit images (pp. 127 – 131). Erase the images (pp. 29, 120) to open space for new
images, or insert an empty memory card (p. 18).
Change the battery pack. (p. 15)
No Image.
RAW
•
There are no images recorded on the memory card that can be displayed.
COP
•
Unsupported images, or images with corrupted data cannot be displayed.
•
Images manipulated on a computer, that have had their file name changed, or have been taken with a different camera may not display.
Cannot magnify!/Cannot play back this content in Smart Shuffle/Cannot rotate/Cannot modify image/Cannot register this image!/Cannot modify/
Cannot assign to category/Unselectable image.
•
Incompatible images cannot be magnified (p. 113), played back in Smart Shuffle
(p. 113), tagged as favorites (p. 122), rotated (p. 126), edited (pp. 127 – 131),
registered to the start-up screen (p. 143), categorized (p. 123), or added to a print list
•
Images manipulated on a computer, that have had their file name changed, or have been taken with a different camera may not be magnified, played back in Smart
Shuffle, tagged as favorites, rotated, edited, registered to the start-up screen, categorized, or added to a print list.
•
Movies cannot be magnified (p. 113), played back in Smart Shuffle (p. 113), edited
(pp. 127 – 131), added to a print list (pp. 136, 137), or registered to the start-up screen
List of Messages That Appear on the Screen
Invalid selection range
•
When choosing the selection range (pp. 118, 121, 125, 139), you tried to choose a
starting image that was after the last image or you tried to choose an ending image that was before the starting image.
Exceeded selection limit
•
You chose more than 998 images in print settings. Choose less than 998 images
•
Print settings could not be saved correctly. Reduce the number of selected images and
•
You chose 501 or more images in Protect (p. 117), Erase (p. 120), Favorites (p. 122),
My Category (p. 123) and Print Settings (pp. 136, 138).
Communication error
•
Images could not be transferred to the computer or printed due to the large amount of
•
images (approx. 1000) stored on the memory card. Use a commercially available USB card reader to transfer the images. Insert the memory card into the printer’s card slot to print.
Naming error!
Y name as the folder or image that the camera is attempting to create, or the highest possible file number has already been reached. In the
3 menu, change [File
•
Numbering] to [Auto Reset] (p. 144) or format the memory card (p. 23).
Lens Error
•
If this error message continues to appear, contact a Canon Customer Support Help
Desk as there may be a problem with the lens.
A camera error was detected (Error number)
•
If an error code appears directly after taking a picture, the shot may not have been recorded. Check the image in Playback mode.
•
If this error code reappears, note the Error number (Exx) and contact a Canon
Customer Support Help Desk as there may be a problem with the camera.
161
Information Displayed on the Screen
Shooting (Information Display)
162
*
Battery Charge Indicator
Movies: Remaining Time
Y
Self-Timer
Camera Orientation*
Camera shake warning
Spot AE Point Frame
COP
Image Quality
Digital Tele-converter
Shutter Speed
Aperture Value
Exposure Compensation
Super Slow Motion Movie
Still Images: Recordable
Flash Mode
Eye-Fi Connection
Red-Eye Correction
Exposure Shift Bar
: Standard, : Held vertically
When shooting, the camera detects if it is held vertically or horizontally, and adjusts settings accordingly for the best shot. It also detects orientation during playback, so you can hold the camera in either orientation and it will automatically rotate images for correct viewing.
This function may not operate correctly when the camera is pointed straight up or down.
Information Displayed on the Screen
Scene Icons
In
A mode, the camera displays an icon for the scene it has determined and then automatically focuses and selects the optimum settings for subject brightness and color.
Subject People
Background
When
Moving
With
Strong
Facial
Shadows
Non-
Human
Subjects/
Landsca pes
Close
Subjects
Icon
Background
Color
Bright
Gray
Including
Blue Skies
Dark
Backlit
Backlit
Sunsets
Spotlights
*
—
—
—
COP
Y
*
—
—
When
Using
Tripod
—
* Appears when the scene is dark and the camera is attached to a tripod.
Light Blue
Orange
Dark Blue
163
Information Displayed on the Screen
Playback (Detailed Information Display)
164
Eye-Fi Transfer
Battery Charge Indicator
Y
Still Images: Recording
Movies: Movie Length
Playback Speed
Exposure Compensation
Folder Number – File
COP
Displayed image number
/ Total number of images
Shutter Speed, Movie
Quality, Frame Rate
Image Editing
Compression (Image Red-Eye Correction
Aperture Value
Shooting Date and Time
MOV (Movies)
Handling Precautions
•
This camera is a high-precision electronic device. Do not drop it or subject it to strong impacts.
•
Never place the camera close to magnets, motors or other devices that generate strong electromagnetic fields. Exposure to strong magnetic fields may cause malfunctions or corrupt image data.
•
If water droplets or dirt become stuck on the camera or screen, wipe with a dry soft cloth or eyeglass wiper. Do not rub or apply force.
•
Never use cleaners containing organic solvents to wipe the camera or screen.
•
Use a commercially available blower brush to remove dust from the lens.
For stubborn dirt contact a Canon Customer Support Help Desk as listed on the customer support leaflet supplied with your camera.
•
When you move the camera rapidly from cold to hot temperatures,
Y and let it adjust to temperature changes slowly before removing it from the bag.
•
If condensation has formed on the camera, stop using it immediately, as continued use may damage the camera. Remove the battery and memory resuming use.
COP
165
166
Functions Available in Each Shooting Mode
Shooting modes
4
A
G I V
Function
Self-Timer (pp. 60, 66, 80, 81)
AE Lock/Exposure Shift (p. 102)
$
Ò Î
{ { { { — — —
{
{ { { — — —
— — — — — — —
—
{ — — — — —
h
…
!
{ { { { { { {
—
{ { { { { {
*
2
{ — — — — —
{ { { { { { { e u
Func. Menu
—
Y
{ — — — — —
{ { { { { { {
—
{ — — — — —
—
{ — — — — —
{ { { { { { {
COP
—
{ — — — — —
{ { { { { { {
—
{ — — — — —
{ { { { { { {
—
{ { { { { { {
{ — — — — —
—
{ — — — — —
—
{ { { { { {
W
{ { { { — — —
—
{ { { — — —
—
{ { { — — —
{ { { { { { {
{ { { { { { {
{ { { { { { {
*1 The number of shots cannot be specified, and the time delay cannot be set to 0 seconds.
*2 Not selectable but switches to
… depending on the circumstances.
*3 Not selectable but switches to
… when the flash fires.
*4 White Balance data not recordable.
*5
Functions Available in Each Shooting Mode
4
E
T Y w O P t
≈ xv E
— — { { { {
{ { { { { { { { { { { { {
— — { { { {
*
1
*
1
*
1 { { { { {
*
1
*
1
*
1
*
1
*
1
— — — — — — — — — — — — — — —
{
— — —
— — — — — — — — — — — — — — — — — — —
— — — { { {
{ { { { { { — —
— — — — —
— — — — { {
{ { { { { { — { {
— — — —
— — — — — — — — — — — — —
*
3
{
— — — —
{ { { { { { { { { { { { { { {
— — — —
{ — — — — — {
— — — — — — {
{ { {
—
{
{ { { { { { { { { { { { { { { { { { {
{ — — — — — {
— — — — — — {
{ { {
—
{
— — — — — — — — — — — — — {
Y
—
{
— — —
Func. Menu
{ { { { { { { { { { { { { { { { { { {
— — — — — — — — — — — — — — — — — — —
{ { { { { { { { { { { { { { { { { { {
— — — — — — —
COP
{ {
— — —
{ { { { { { { { { { { { { { { { { { {
{ — — { — —
— — — — — — — {
*
4 {
— — —
{ { { { { { { { { { { { { { { { { { {
— — — — — — — — — — — — — — — — — — —
{ — { { { —
—
{ { { { { { — {
— — — —
— — { { { {
{ { { { { { { { {
— — — —
{ { — { { { { { { { { { { —
— — — — —
— — — { { {
*
6
*
6
*
7
*
6
{ { { { { {
*
5
— —
{ { { { { { { { { {
*
8
—
{
—
{
—
{
—
{
{ { { { { { { { { { { { { { { {
*
9
*
10 {
{ { { { { { { { { { { { { { { { { { {
*6 Recording pixels are fixed to
*7 Fixed to .
*8 Recording pixel setting
.
not selectable.
*9 Fixed to
*10 or
.
is not available.
>z
{ Selectable, or set automatically. – Not selectable
167
168
Menus
4 Shooting Menu
Shooting Modes
4
A
G I V
Function
Face Detect
Center
Normal/Small
Standard
{ { { { { { {
Off
{ { { { { { {
Digital Tele-converter (1.4x/2.3x)
{ { { { { { {
Flash Settings
On/Off
On/Off
On/Off
On/Off
Red-Eye Corr.
On/Off
Red-Eye Lamp On/Off
{ { {
—
{ { {
*
*
3
4
Y
{ {
*
4
{ {
—
— — —
*
4
{ { { {
*
4
{ {
{ { { { { { {
{ { { { { { {
*
4
*
4
Auto/Off
Off/2 – 10 sec./Hold
On/Off
COP
*
5 { — — — — —
{ { { { { { {
{ { { { { { {
{ { { { { { {
Grid Lines
3:2 Guide
{ { { { { { {
{ { { { { { {
Continuous/Off
*
6 { { { { { {
—
{ { { { { {
Shoot Only/Panning
Off/Date/Date & Time
*
1
{ { { { { {
—
{ { {
— — —
—
{ — — — — —
{ { { { { { {
*1 9 points when a face is not detected.
*2 Only available for shooting still images.
*3 [On] when movement is detected.
*4 Fixed to [On].
*5 Fixed to [Auto].
*6 Fixed to [Continuous].
Menus
4 E
T Y w O P t
≈ xv E
{
{
{ {
— —
*
1
{
{
{
{
{
{
{
— — { { { — {
{ — { { { { {
—
{
*
2
*
2
*
2
*
2
—
—
*
2
*
2
— — — — — — — — — — — — — — — — — — —
— — — — { { — — — { { { { { —
{
— — —
{ { { { { { { { { { { { { { { { { { {
— — — — { { — — — { { { { { — — — — —
{ {
—
{ { { {
— — { { { — { — — — — —
— — —
{ { { {
— — { { { — — — — — — —
*
4
{
*
4
{
{
{
— { {
{ { {
{
{
{
{
{
{
{
{
{
{
{ — {
{ — {
Y
{
{
*
4
{
*
4
{ { {
— — —
{ { {
— — — { { { — { — — — — —
— — —
{ { { { { { { { { — { {
— — — —
*
4
*
4
*
5
*
5
*
5
—
— — —
{
— — — — — — — — — — — — — — —
{ { { { { { { { { { { { { { {
— — — —
{ { { { {
{
{
{
COP
{ { {
— — — — —
— — — — —
{ { { { { { { { { { { { { {
—
{ { { {
{ { { { { { { { { { { { { {
— — — — —
{ {
*
6
{ { { { { { { { { { { { { { { {
{ {
—
{ { { { { { { { { { { {
— — — —
— — — — { {
{ { { { { { { {
— — — — —
{ Selectable, or set automatically. – Not selectable
>z
169
170
Menus
3 Set up Menu
Item
Mute
Volume
Sound Options
Hints & Tips
LCD Brightness
Start-up Image
Format
File Numbering
Create Folder
Lens Retract
Power Saving
Time Zone
Date/Time
Video System
Eye-Fi Settings
Language
Reset All
* Default setting
2 Print Menu
Content
On/Off*
Set all operation sounds (5 levels).
Set the sounds for each camera operation.
On*/Off
Set within a range of ±2.
Add an image as a start-up image.
Formats memory card, erasing all data
Continuous*/Auto Reset
Monthly*/Daily
1 min.*/0 sec.
Auto Power Down: On*/Off
Home*/World
Y
Date and time settings
NTSC* / PAL
Eye-Fi connection settings (only appears when
Eye-Fi card is inserted)
COP
Ref. Page
Item
Select Images & Qty.
Select Range
Select All Images
Clear All Selections
Print Settings
Content
Displays printing screen (When connected to a printer).
Chooses individual images for printing.
Chooses starting and ending images for printing.
Chooses all images for printing.
Cancels all settings for printing.
Sets the printing style.
Ref. Page
—
Playback Mode FUNC. Menu
1 Playback Menu
Slideshow
Item
Erase
Protect
Protect
Favorites
Erase
Play Movie
Smart Shuffle
Filtered Playback
Slideshow
My Category
Content
Plays back images automatically.
Erases images (Select, Select Range, All
Images)
Protects images (Select, Select Range, All
Images)
Rotates images.
Tags or untags images as favorites.
Rotate
Favorites
My Category Categorizes images (Select, Select Range) i-Contrast Corrects dark portions and contrast in still
Red-Eye Correction
Trimming
Resize
My Colors
Scroll Display images.
On*/Off
Corrects red eyes in still images.
Trims portions of still images.
Resizes and saves still images.
Adjusts colors in still images.
Y
Resume
Transition
* Default setting
Last seen*/Last shot
Fade*/Scroll/Slide/Off
COP
Item Content
Rotate
Print List
Rotates displayed image.
Selects or clears settings for printing displayed image. (Print appears when the camera is connected to the printer)
Protects/unlocks displayed image.
Tags/untags displayed image as favorites.
Erases displayed image.
Starts Play Movie.
Starts Smart Shuffle.
Filters/cancels filter for displayed image.
Plays back images automatically.
Categorizes images.
Ref. Page
Ref. Page
171
172
Specifications
Image Sensor
Camera Effective Pixels ..... Approx. 10 million pixels
Lens
Focal Length ...................... 10x zoom: 6.3 (W) – 63.0 (T) mm (35mm film equivalent: 36 (W)
– 360 (T) mm)
Focusing Range ................. 1 cm (0.4 in.) – infinity (W), 1 m (3.3 ft.) – infinity (T)
• Macro: 1 – 50 cm (0.4 in. – 1.6 ft.) (W)
Image Stabilizer (IS) System Lens-shift type
Imaging Processor .................. DIGIC 4
LCD Monitor
Type ................................... TFT color (wide viewing angle type)
Size .................................... 3.0 type
Effective Pixels................... Approx. 230,000 dots
Aspect Ratio....................... 16:9
Function ............................. Brightness adjustment (5 levels), Quick-bright LCD
Focus
Control System................... Autofocus: Single (Continuous in Auto mode), Continuous
Servo AF (Servo AE)
AF Frame ........................... Face Detect, Center
Y
Metering Method ..................... Evaluative, Center-weighted average, Spot
Exposure Compensation (Still Images)
/Exposure Shift (Movies) ......... 2 stops in 1/3-stop increments
ISO Speed............................... Auto, ISO 125/200/400/800/1600/3200
(Standard Output Sensitivity,
Recommended Exposure Index)
COP
Custom
Shutter Speeds........................ 1 – 1/4000 sec.
15 – 1/4000 sec. (Total shutter speed range)
Aperture
Type ................................... Blade (x2) f/number ............................. f/3.4 – f/7.1 (W), f/5.6 – f/9.0 (T)
Flash
Flash Mode ........................ Auto, on, Slow Synchro, off
Range................................. 30 cm – 3.5 m (W), 1.0 – 2.0 m (T)
(12 in. – 12 ft. (W), (3.3 – 6.6 ft. (T))
Shooting Mode ........................ Auto, P, Portrait, Kids&Pets, Smart Shutter*
1
, High-speed Burst,
Best Image Selection, Handheld Night Scene, Low Light, Super
Vivid, Poster Effect, Color Accent, Color Swap, Fish-eye Effect,
Miniature Effect, Beach, Foliage, Snow, Fireworks, Long
Shutter, Stitch Assist, Movie*
2
*
3
*1 Smile, Wink Self-timer, Face Self-timer
*2 Smart Auto available
*3 Standard, Super Slow Motion, Miniature Effect, Color
Accent, Color Swap
Specifications
Digital Zoom ............................ Still images/Movies: Approx. 4x (up to approx. 40x in combination with the optical zoom)
Safety Zoom, Digital Tele-converter
Continuous Shooting
Modes................................. Normal, AF, LV
Speed (Normal) .................. Approx. 3.7 shots/sec. (In P mode)
Approx. 8.8 shots/sec. (In High-speed Burst mode)
Number of Possible Shots
(CIPA compliant) ..................... Approx. 150 shots
Recording Media ..................... SD memory card, SDHC memory card, SDXC memory card,
MultiMediaCard, MMCplus card, HC MMCplus card
File Format .............................. Design rule for Camera File system, DPOF (Version 1.1) compliant
Data Type
Still Images......................... Exif 2.3 (JPEG)
Movies ................................ MOV (Image data: H.264, Audio data: Linear PCM (stereo))
Recording Pixels
Still images ......................... Large: 3648 x 2736, Medium 1: 2816 x 2112, Medium 2: 1600 x
1200, Small: 640 x 480, Widescreen: 3648 x 2048
Selection, and Low Light
Y
• Fixed to 1824 x 1368 when in High-speed Burst, Best Image
Movies ................................ Smart Auto, Standard, Color Accent, Color Swap: 1920 x 1080
(24 fps*
1
), 1280 x 720 (30 fps*
2
), 640 x 480 (30 fps*
2
), 320 x 240
(30 fps*
2
)
Super Slow Motion: 320 x 240 (240 fps*
COP
Playback: 30 fps*
Playback: 30 fps*
*1 Actual frame rate is 23.976 fps.
3
when shooting, 30 fps*
2
during playback)
Miniature Effect: 1280 x 720 (Shooting: 6 fps/3 fps/1.5 fps,
2
), 640 x 480 (Shooting: 6 fps/3 fps/1.5 fps,
2
)
*2 Actual frame rate is 29.97 fps.
*3 Actual frame rate is 239.76 fps.
Interface................................... Hi-Speed USB
HDMI output
Analog audio output (stereo)
Analog video output (NTSC/PAL)
Direct Print Standard ............... PictBridge
Power ...................................... Battery Pack NB-9L
AC Adapter Kit ACK-DC70
Dimensions (CIPA compliant).. 101.3 x 58.5 x 22.3 mm (3.99 x 2.30 x 0.88 in.)
Weight (CIPA compliant) ......... Approx. 190 g (6.70 oz.) (Including the battery and memory card)
Approx. 167 g (5.89 oz.) (camera body only)
173
174
Specifications
Battery Pack NB-9L
Type ........................................ Rechargeable lithium-ion battery
Nominal Voltage ...................... 3.5 V DC
Nominal Capacity .................... 870 mAh
Battery Life (Charge Cycles) ... Approx. 300 times
Operating Temperatures ......... 0 – 40 °C (32 – 104 °F)
Dimensions.............................. 14.6 x 43.1 x 15.3 mm (0.57 x 1.70 x 0.60 in.)
Weight ..................................... Approx. 21 g (0.74 oz.)
Battery Charger CB-2LB/CB-2LBE
Regions ................................... CB-2LB: Japan/Americas
CB-2LBE: Europe/Asia/Oceania
Rated Input.............................. 100 V – 240 V (50/60 Hz)
8.5 VA (100 V) – 12 VA (240 V)
0.085 A (100 V) – 0.05 A (240 V)
Rated Output ........................... 4.2 V, 0.7 A
Y
Two indicator system
Operating Temperatures ......... 0 – 40 °C (32 – 104 °F)
Dimensions.............................. 82.0 x 59.0 x 24.5 mm (Protrusion: 26.4 mm)
(3.23 x 2.32 x 0.96 in. (Protrusion:1.04 in.))
Weight ..................................... CB-2LB: Approx. 73 g (2.57 oz.)
COP
•
All data is based on tests by Canon.
•
Camera specifications or appearance are subject to change without notice.
Index
Numerics D
3:2 Guide ................................................. 149
A
AC Adapter Kit................................... 39, 154
Accessories ............................................... 39
AE Lock ............................................. 88, 102
AF Frames .................................... 26, 84
AF Lock....................................... 86, 162
AFB Mode................................................ 162
AF-Point Zoom .......................................... 85
AUTO Mode (Shooting Mode) ................... 25
Date/Time
Adding to Image..................................59
Changing ............................................21
Date/Time Battery...............................21
Setting.................................................20
World Clock ......................................146
Default Settings .........................................50
DIGITAL CAMERA Solution Disk ................2
Digital Tele-Converter................................58
Digital Zoom ..............................................57
Display Language......................................22
AV Cable ................................................. 115
Battery
B
Battery Charger .................................. 14
Charge Indicator ................................. 15
Date/Time Battery............................... 21
Editing
DPOF...............................................136, 137
Drive Mode ................................................78
Dynamic Mode.........................................150
Y
E
i-Contrast ..........................................130
My Colors..........................................129
Power Saving.............................. 51, 145
Recharge ............................................ 14
Battery Charger ..................................... 2, 39
Black and White Images............................ 79
Blink Detection........................................... 91
Red-Eye Correction ..........................131
Resizing (Making Images Smaller) ...127
Trimming...........................................128
Erasing Images..................................29, 120
Error Messages .......................................160
Exposure
AE Lock ......................................88, 102
C
Correction ...........................................72
FE Lock...............................................88
Shift...................................................102
Eye-Fi Card .......................................16, 155
Camera
Default Settings .................................. 50
Holding the Camera............................ 13
Camera Shake............................. 27, 56, 150
Center (AF Frame Mode) .......................... 84
Clock Functions......................................... 51
Color Accent (Shooting Mode) ............ 92, 98
Color Swap (Shooting Mode) .............. 93, 98
Components Guide.................................... 42
Compression (Image Quality).................... 74
Continuous Shooting ................................. 78
AF ....................................................... 78
Best Image Selection.......................... 68
High-speed Burst................................ 67
LV ....................................................... 78
F
Face Detect (AF Frame Mode)..................84
Face Self-Timer (Shooting Mode) .............66
Factory Settings J Default Settings
FE Lock .............................................88, 162
File Numbering ........................................144
Filtered Playback .....................................109
Fireworks (Shooting Mode) .......................63
Fish-eye Effect (Shooting Mode) ...............69
Flash
Off .......................................................56
175
Index
176
Long Shutter (Shooting Mode) .................. 95
Low Light (Shooting Mode) ....................... 62
On....................................................... 73
Slow Synchro...................................... 89
Focus
AF Frame...................................... 26, 84
AF Lock .............................................. 86
AF-Point Zoom ................................... 85
Servo AF............................................. 86
Focus Check ........................................... 112
Focus Lock................................................ 82
Foliage (Shooting Mode) ........................... 62
Format J Memory Cards, Formatting
Formatting (Memory Card) .................. 23, 52
FUNC. Menu
List .................................................... 171
M
Magnified Display .................................... 113
Manual White Balance .............................. 77
Memory Cards........................................... 16
Available Shots............................. 19, 75
Formatting .................................... 23, 52
Shooting Time ............................ 31, 101
Menu
Basic Operations ................................ 47
List .................................................... 168
Menu................................................... 46
G
Grid Lines........................................ 149, 162
Handheld NightScene (Shooting Mode).... 62
Images
H
Movies
Metering Method ....................................... 87
Miniature Effect (Movie Mode) .................. 99
Miniature Effect (Shooting Mode).............. 70
Modes................................................. 98
Movie Quality (Recording Pixels/
Frame Rate) ..................................... 101
High-speed Burst....................................... 67
Household Power.................................... 154
I
Image Quality J Compression Ratio
Display Time..................................... 148
Shooting Time ............................ 31, 101
Viewing (Playback) ..................... 32, 104
MultiMediaCard/MMCplus J Memory Cards
My Category ............................................ 123
My Colors .................................................. 79
P
Erasing Images........................... 29, 120
Protect .............................................. 117
Indicator............................................... 43, 45
Interface Cable .............................. 2, 35, 134
ISO Speed......................................... 76, 162
K
P (Shooting mode) .................................... 72
Personal Printing Guide .............................. 2
PictBridge .......................................... 40, 134
Playback With Transition Effects............. 114
Portrait (Shooting Mode) ........................... 61
Poster Effect (Shooting Mode) .................. 63
Power J Battery, AC Adapter Kit
Power Saving .................................... 51, 145
Printing .................................................... 134
Program AE............................................... 72
Protect ..................................................... 117
Kids&Pets (Shooting Mode) ...................... 61
L
Lamp ......................................... 42, 147, 148
LCD Monitor (Screen) ................................. 3
Super Vivid (Shooting Mode).....................63
R
T
Recording Pixels (Image Size) .................. 74
Red-Eye Correction ........................... 90, 131
Resizing (Making Images Smaller).......... 127
Rotate ...................................................... 126
S
Tag Images as Favorites .........................122
Terminal.....................35, 115, 116, 134, 154
Travel Abroad ..............................15, 39, 146
Trimming..................................................128
Troubleshooting.......................................157
Screen
Display Language............................... 22
V
Information Display................... 162, 164
Viewing
Switching the Display.......................... 44
Filtered Playback ..............................109
SD/SDHC/SDXC Memory Card J Memory
Images on a TV ........................115, 116
Cards
Self-Timer
10 Second Self-Timer ......................... 60
Shots .................................................. 81
Face Self-Timer (Shooting Mode)....... 66
Two Second Self-Timer ...................... 80
Wink Self-Timer (Shooting Mode)....... 65
Index Display ....................................108
Magnified Display .............................113
Single Image Playback .......................28
Viewing Images on a TV..................115, 116
W
Sepia Tones .............................................. 79
Servo AF.................................................... 86
Shooting
Shooting Date and Time J Date/Time
Shooting Info .................................... 162
Shooting Time............................. 31, 101
White Balance ...........................................77
Wide (Recording Pixels) ......................74, 75
Wink Self-Timer (Shooting Mode) .............65
World Clock .............................................146
Zoom .............................................25, 30, 57
Z
Shooting Using a TV.................................. 82
Slideshow ................................................ 110
Smart Shuffle........................................... 113
Smile (Shooting Mode) .............................. 64
Snow (Shooting Mode).............................. 63
Software
DIGITAL CAMERA Solution Disk ......... 2
Installation........................................... 34
Software Guide ..................................... 2
Transferring Images to a Computer for
Viewing ............................................... 33
Sound Settings .......................................... 48
Stereo AV Cable.................................. 2, 115
Stitch Assist (Shooting Mode) ................... 96
Strap.......................................................... 13
Super Slow Motion (Movie Mode) ............. 99
177
Index
178
MEMO
COP
Y
MEMO
COP
Y
179
Disclaimer
• Reprinting, transmitting, or storing in a retrieval system any part of this guide without the permission of Canon is prohibited.
• Canon reserves the right to change the contents of this guide at any time without prior notice.
• Illustrations and screenshots in this guide may differ slightly from the actual equipment.
Y
• The above items notwithstanding, Canon accepts no liability for damages due to mistaken operation of the products.
COP
CDP-E104-020 © CANON INC. 2010
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project