Samsung DS 24D Product specifications

iii
Copyright © Samsung Electronics Co., Ltd. 2003
All rights reserved. Samsung, the Samsung logo, Samsung iDCS 100 are registered trademarks. All
other product names are used for identification only and may be trademarks and/or registered
trademarks of their respective companies. Product specifications subject to change without notice.
No part of this manual may be reproduced in any form or by any means – graphic, electronic or
mechanical, including recording, taping, photocopying or information retrieval systems – without
express written permission of the publisher of this material.
iv
PREFACE
About This Manual
iDCS 100, Digital Communication System, is a digital telephone system designed for small to
medium–sized businesses.
This manual provides an overview of the Samsung iDCS 100, Digital Communication System,
including system structure and hardware, features and facilities and specifications.
This guide consists of the following chapters.
! Introduction to System
! Hardware Descriptions
! Specifications
! Business Feature Package
! General User Information
Supporting Documents
Further detail on all of the aspects covered in this manual is included in the system Installation and
Programming guide.
The iDCS 100 system provides the following manuals for more information:
! General Description Guide
This manual provides an overview of the Samsung iDCS 100, Digital Communication System,
including system structure and hardware, features and facilities and specifications.
! Installation Guide
This manual provides the information about installation of the Samsung iDCS 100, Digital
Communication System, including information about connecting the equipments.
! Programming Guide
iDCS 100 system provides MMC(Man Machine Communication) program. Users can configure the
system using the MMC program at the digital telephone.
The Programming Guide describes how to use the MMC program.
v
Table of Contents
CHAPTER
1
INTRODUCTION TO SYSTEM............................................................................................ 1-1
GENERAL DESCRIPTION ................................................................................................................ 1-1
SIZE AND CONFIGURATION............................................................................................................. 1-2
TECHNOLOGY ............................................................................................................................... 1-7
PROGRAMMING ............................................................................................................................. 1-8
CHAPTER
2
HARDWARE DESCRIPTIONS............................................................................................ 2-1
KEY SERVICE UNIT........................................................................................................................ 2-1
EXPANSION CABINET ..................................................................................................................... 2-2
INTERFACE CARDS ........................................................................................................................ 2-3
STATION EQUIPMENT ..................................................................................................................... 2-5
iDCS SERIES EQUIPMENT .................................................................................................................. 2-5
DCS SERIES EQUIPMENT ................................................................................................................... 2-7
CHAPTER
3
SPECIFICATIONS .............................................................................................................. 3-1
CHAPTER
4
BUSINESS FEATURE PACKAGE ...................................................................................... 4-1
SYSTEM FEATURES.................................................................................................................. 4-2
SYSTEM FEATURE DESCRIPTIONS ................................................................................................... 4-3
STATION FEATURES ............................................................................................................... 4-25
STATION FEATURE DESCRIPTIONS ................................................................................................. 4-25
DISPLAY FEATURES ............................................................................................................... 4-32
DISPLAY FEATURE DESCRIPTIONS ................................................................................................. 4-32
SAMPLE DISPLAYS............................................................................................................................ 4-36
SAMPLE CALLER ID DISPLAYS......................................................................................................... 4-37
SAMPLE UCD DISPLAYS ......................................................................................................... 4-38
SAMPLE SMDR PRINTOUT (WITHOUT CALLER ID) .............................................................. 4-39
SAMPLE SMDR PRINTOUT (WITH CALLER ID) ................................................................................. 4-39
SAMPLE SMDR PRINTOUT (WITH CALLER ID) ................................................................................. 4-40
SAMPLE UCD REPORT ........................................................................................................... 4-41
UCD CALL STATISTICS ........................................................................................................... 4-42
UCD AGENT STATISTICS ........................................................................................................ 4-44
SAMPLE TRAFFIC REPORT.................................................................................................... 4-45
TRAFFIC REPORT OVERVIEW ............................................................................................. 4-466
SAMPLE ALARM REPORT..................................................................................................... 4-522
DECT SERVICE .......................................................................................................................... 4-53
LIST OF FIGURES
Figure 1–1
Figure 1–2
Figure 1–3
Figure 1–4
Figure 1–5
Figure 1–6
iDCS 100 Configuration Matrix Table (with Analogue Trunks) – Expansion A type.............. 1-3
iDCS 100 Configuration Matrix Table (with Digital Trunks) – Expansion A type................... 1-3
iDCS 100 Configuration Matrix Table (with Analogue Trunks) – Expansion B type.............. 1-4
iDCS 100 Configuration Matrix Table (with Digital Trunks) – Expansion B type................... 1-4
iDCS 100 System Configuration (Basic KSU + Expansion A ) ............................................ 1-4
iDCS 100 System Configuration (Basic KSU + Expansion B ) ............................................ 1-5
Figure 2–1
KSU ................................................................................................................................ 2-1
vi
Figure 2–2 28 Button iDCS Keyset .................................................................................................... 2-5
Figure 2–3 18 Button iDCS Keyset .................................................................................................... 2-5
Figure 2–4 8 Button iDCS Keyset ...................................................................................................... 2-5
Figure 2–5 64 Button iDCS AOM ...................................................................................................... 2-6
Figure 2–6 14 Button iDCS AOM ...................................................................................................... 2-6
Figure 2–7 LCD 24B Euro Keyset ..................................................................................................... 2-7
Figure 2–8 LCD 24B Keyset ............................................................................................................. 2-7
Figure 2–9 STD 12B Keyset ............................................................................................................. 2-7
Figure 2–10 6B LCD Model Keyset .................................................................................................... 2-8
Figure 2–11 48 Button AOM ............................................................................................................... 2-8
Figure 2–12A DS 24S Keyset ............................................................................................................. 2-8
Figure 2–12B DS 24D Keyset ............................................................................................................. 2-9
Figure 2–13 Economic Keyset ........................................................................................................... 2-9
Figure 2–14 Door Phone Interface Module ....................................................................................... 2-10
Figure 2–15 Door Phone .................................................................................................................. 2-10
Figure 2–16 Single Line Telephone .................................................................................................. 2-10
1-1
Chapter 1 Introduction To System
This chapter describes the introduction to iDCS 100 system as follows.
! General Description
! Size and Configuration
! Technology
! Programming
General Description
iDCS 100, Digital Communication System, is a digital telephone system designed for small to
medium–sized businesses. It can operate with the functionality of a square key system, PABX or a
combination of both (hybrid). iDCS 100 employs the very latest DSP technology (Digital Signal
Processors).
iDCS 100 offers a variety of interface cards that allow connection to the public telephone network or
private networks. These are generally referred to as trunk cards. Two types of telephones can be
connected to the systems. Proprietary digital phones called "Keysets" connect to digital line interface
cards (DLI). Standard telephone sets generally called "single line telephones" connect to single line
interface cards (SLI). In addition, DLI station ports are used to connect peripheral devices such as
door phones and add–on modules. Miscellaneous circuits are provided to allow such optional
features as external paging, music on hold, background music, common audible devices, alarms and
emergency power failure telephones.
All DCS keysets utilize a single PCB with surface–mounted components assuring the highest product
quality and long life. Samsung's customary large, easy–to–read displays and LEDs in the button
design make them much easier to use. In many instances, sophisticated features are made simple
through the use of friendly display prompts or push–on/push–off feature keys.
1. 'DCS' is the general term used in the text to refer to all systems. Any differences
between the systems are indicated under separate headings ‘iDCS 100’ and 'DCS'.
2. It is not possible to expand from iDCS 100 to a DCS system nor to expand from DCS
Compact II to iDCS 100.
1-2
Chapter 1
Introduction To System
Size and Configuration
The iDCS 100 system consists of the basic Key Service Unit, an Expansion cabinet, Interface cards and
Digital keysets. The Key Service Unit begins with eight (8) keyset ports expandable to 18 analogue
C.O. line ports, or 24 lines if 4 BRI cards are used, or 32 stations. In addition, up to 8 keyset daughter
boards may be added to the system along with the optional 2 SLI card.
The Expansion cabinet A type has three Universal slots and one DCS slot for TEPRI(PRI) or VM
service, which provides the maximum configuration of 66 ports with analogue trunk lines or 96 ports
with Digital trunk lines.
The Expansion cabinet B type has two Universal slots and two DCS slot for TEPRI(PRI) or VM service,
which provides the maximum configuration of 58 ports with analogue trunk lines or 88 ports with
Digital trunk lines.
Two types of telephones can be connected to the system: proprietary digital stations called "keysets"
that connect to DLI (Digital Line Interface) ports and standard telephone sets, generally called "single
line telephones", that connect to SLI (Single Line Interface) ports.
The system also has an optional MISC card which provides Music on Hold facilities, two serial I/O
ports and other useful facilities.
The following charts (Figures 1–1, 1–2, 1-3, 1-4) describe configurations using the basic Key Service
Unit (KSU), an Expansion cabinet and expansion cards. However, by using the DCS's unique keyset
daughter boards (KDbs), which are installed in the base of a digital keyset, the capacity of the system
can be increased by one station per KDb. Installing a KDb–DLI adds another digital port while a KDb–
SLI adds a single line port. Mix and match these two types of KDb to get up to a total of 8 KDbs in the
system. Using this method allows the iDCS 100 to expand to a maximum of 64 stations. Adding the
optional 2 SLI card to the KSU provides a further two SLI ports. The combination of the basic 008 KSU
plus three expansion cards in the KSU plus three expansion cards and one DCS card in the Expansion
cabinet plus 8 KDbs plus a 2 SLI card provides a maximum configuration of 96 ports plus
Miscellaneous card.
1. Only one 2 SLI card can be installed in the system.
2. Only one MISC card can be installed in the system.
3. Only three expansion cards can be installed in the Key Service Unit.
4. Expansion A type consists of three universal expansion slots and one DCS card slot
for TEPRI(PRI) or SVMi-8.
Expansion B type consists of two universal expansion slots and two DCS card slot for
TEPRI(PRI) and SVMi-8.
5. Only 8 KDbs can be installed in the keysets connected to the 008 Basic KSU
6. iDCS 100 system can have up to 48 stations if SVMi-8 is not used up to 40 stations if
SVMi-8 is used.
1-3
Figure 1–1 iDCS 100 Configuration Matrix Table (with Analogue Trunks) – Expansion A type
Trunk Lines
36
Two Cabinets
30
24
18
12
KSU
6
0
8
16
18
26
34
Station Lines
Figure 1–2 iDCS 100 Configuration Matrix Table (with Digital Trunks) – Expansion A type
Trunk Lines
42
50
58
66
1-4
Chapter 1
Introduction To System
Figure 1–3 iDCS 100 Configuration Matrix Table (with Analogue Trunks) – Expansion B type
Trunk Lines
Figure 1–4 iDCS 100 Configuration Matrix Table (with Digital Trunks) – Expansion B type
Trunk Lines
The Figure 1–5 describes iDCS 100 system configuration using the Basic Key Service Unit (KSU) and
Expansion A type cabinet.
The Figure 1–6 describes iDCS 100 system configuration using the Basic Key Service Unit (KSU) and
Expansion B type cabinet.
1-5
Figure 1–5 iDCS 100 System Configuration (Basic KSU + Expansion A )
CHAMP connector
P5
P2
CHAMP connector
P1
2
S
L
I
M
E
M
M
I
S
C
S
L
O
T
1
S
L
O
T
2
S
L
O
T
3
P4
S
L
O
T
4
Ringer
PLL
Power Supply
Figure 1–6 iDCS 100 System Configuration (Basic KSU + Expansion B )
S
L
O
T
5
S
L
O
T
6
D
C
S
P
R
I
1-6
Chapter 1
Introduction To System
1. Only one 2 SLI card can be installed in the KSU.
2. Only one MISC card can be installed in the KSU.
3. Only three expansion cards can be installed in the KSU and the additional can be
added in the Expansion cabinet when expanded.
4. Only 8 KDbs can be installed in the keysets connected to the Basic KSU.
5. ISDN cards(BRI, PRI and TEPRI) require a PLL card installed in the KSU.
1-7
Technology
Switching
System switching is accomplished by means of a custom IC "engine" that provides 256 switchable
digital channels. The engine is controlled by its own 16–bit Motorola MC 68000 microprocessor and
switching control program. Each of the 256 digital channels is automatically assigned to carry voice or
data as required by system operation in a PCM format.
In addition to the 256 channels mentioned above, the systems also utilize Digital Signal Processors
(DSPs). Each DSP may be configured by the switching control program as a DTMF sender, a DTMF
receiver or as a C.O. tone detector on a per–call basis. Each engine chip contains 4 DSP channels.
Four additional DSPs are added when a MISC card is installed. This means that the system contains a
total of 8 DSP channels when fully expanded. The DSP channels are fully shared throughout the
system as a common resource.
Memory
The systems operate using stored program control. This program is stored in EPROM chips or flash
menory. All specific customer data is stored in RAM(Random Access Memory) which is protected
against the loss of AC power to the system by an on–board battery backup system.
Microprocessors
iDCS 100 uses distributed processing. The primary processor of the system is a 16–bit Motorola
MC68000 operating at a clock speed of 16 MHz. Secondary processing is in the some special cards like
as BRI and also done in the keysets. The digital keyset uses a Hitachi H8 processor for data
communication within the iDCS 100.
1-8
Chapter 1
Introduction To System
Programming
The iDCS 100 system arrives from the factory with default data.
Connect it to trunks, stations and power.
Turn the system on and it is fully operational.
The only thing left to do is customize the data to fit the customer’s needs. This is called programming
the system.
MMC stands for Man Machine Communication and each program is assigned a different three digit
code(e.g. 100). These MMC codes are used to view, create or change customer data. Programming is
simply deciding what needs to be done and knowing which MMC is used to do it. For example: use
MMC 601 to designate a station group; enter system speed dial numbers in MMC 705.
Programming Levels
There are three levels of programming: System, Customer and Station.
System and Customer are under passcode protection while Station programming does not require a
passcode.
To prevent conflicting data from being entered, only one person at a time can enter programming code
with the passcode for technician or customer. While programming is in progress, normal system
operation is not affected. For your convenience, the system displays [xxx PGM MODE] when another
keyset is in the program mode.
System Level
This level is entered via MMC 800 and requires the technician’s passcode. It allows access to all
system programs, station programs and maintenance programs.
Customer Level
This level is entered via MMC 200 and requires the customer’s passcode. It allows access to station
programs and system programs permitted by the technician in MMC 802. When using the customer’s
passcode to access station programs, data for all stations can be viewed or changed.
After opening programming with the customer’s passcode, you must press TRSF key to exit. Then
press TRSF key followed by the MMC number you wish to access.
Station Level
All keysets can access station programs 102~119 without using a passcode.
Each user can only change station data for his/her own keyset.
The iDCS 100 also allows the use of a proprietary computer program called SAPM-PCMMC. This
permits a technician to program the system using a personal computer. SAPM-PCMMC can be used
on-site to modify the customer database or to download (save) the entire customer database to a file.
This file can then be saved as a backup and be uploaded when required to restore the database.
Through the use of SIO, SAPM-PCMMC can access the iDCS 100 system remotely (off-site) to make
database changes or perform uploads or downloads of the customer database as if the technician were
on-site.
2-1
Chapter 2 Hardware Descriptions
This chapter describes the hardware of the iDCS 100 system as follows.
! Key Service Unit
! Interface Cards
! Station Equipment
Key Service Unit
The iDCS 100 Key Service Unit (KSU, Figure 2–1) is a single
metal cabinet containing the following:
! A power supply
! Processing and switching
! Eight 2B+D digital keyset interfaces
! Memory Card
- MEM3: A removable MEM3 card, containing 3Myte
Program memory, 1Mbyte Data memory with a back–up
super capacitor, real time clock, a monitor LED and a
RAM clear switch
- MEM4: A removable MEM4 card, containing 3Myte
Program memory, 1Mbyte Data memory (only
512Kbyte is back-uped), 512Kbyte common menory,
real time clock, a monitor LED, a RAM clear switch,
and LAN interface
Figure 2–1 KSU
! One Internal Music source or an External Music interface for Music–on–Hold and Back–ground
Music
! One External Page interfaces
! One general–purpose Dry contact
! Three universal expansion slots, a MEM3 or MEM4 card slot, a 2 SLI card slot and a MISC card slot
2 Champ connectors for external connections and other connectors for the Expansion cabinet and the
Ring Generator Unit
Ring Generator Unit RGU1 or RGU2
Two kinds of sinusoidal–waveform Ring Generator Units are available. RGU1 drives 3W ring signals
while the other provides 20W ring signals. The larger unit is required when a large number of single
line telephones are operation behind the system.
2-2
Chapter 2
Hardware Descriptions
MISC card MISC 1 or MISC 2
One dedicated slot in the Basic KSU is for an MISC card and two kinds of MISC cards are available.
The MISC 1 card contains one additional External Music Interface for MOH or BGM, one additional
External Page Interface, one Alarm Sensor Detection circuitry, 4 channels DTMF receiver, three
General–purpose Dry contact relays, two RS232C Serial interfaces with connectors for PCMMC and
SMDR and MODEM card interface. The MISC 2 card is similar to the MISC 1 card but is also
equipped with a built–in 4–ch AA function.
It is strongly recommended that this card be used in situations requiring heavy single line telephone
use.
MODEM card
One built–in MODEM card can be installed in a MISC card.
PLL card
Any ISDN card, that is a BRI or a PRI, requires the PLL card which can be installed in a dedicated
place on the KSU motherboard.
MEM3 card
MEM3 card has EPROM memory to support new features Window PC-MMC, ITM3 & TEPRI cards
MEM4 card
MEM4 card with LAN interface module, no selectable options. The LAN module is required to expand
the system memory, to provide SIO ports 1EA, and a 10/100 base T LAN interface processor.
MEM4 card has Flash memory to support new features Window PC-MMC, ITM3, TEPRI cards and
Networking solution by TE/PRI, Program/Database up/download by LAN interface.
Expansion Cabinet
One metal Expansion cabinet can be attached to the Key Service Unit for expansion. Expansion A type
consists of three Universal expansion slots and one DCS card slot for PRI(TEPRI) or SVMi-8.
Expansion B type consists of two Universal expansion slots and two DCS card slot for PRI(TEPRI) or
SVMi-8. The Expansion cabinet connects to the KSU via a 64-pin flat cable, two 2-wire power
connections and a F-GND connection. It contains a 50-pin champ connector for external connections.
Please be noticed that a DCS card has its own connector.
2-3
Interface Cards
2 SLI card
The 2 SLI card is installed in a dedicated slot on the KSU motherboard. The card provides two single
line telephone interfaces equipped with Long Line protection and the ability to provide a loop
disconnect signal.
3 TRK card
The 3 TRK card provides three loop start C.O. interfaces with optional Caller ID relays. The first two
C.O. interfaces are equipped with PFT relays. Each interface contains an interface for MPD or PRS
which is optional. The MPD or PRS hybrid chips of the DCS system can be used.
6 TRK card
The 6 TRK card provides six loop start C.O. interfaces. The first two C.O. interfaces are equipped with
PFT relays. Each interface contains an interface for MPD or PRS which is optional. The MPD or PRS
hybrid chips of the DCS system can be used.
4 BRI card
The 4 BRI card contains four Basic Rate access ports, i.e. eight ISDN channels. Protocol is compatible
for Euro–ISDN BRI. For S0 application, power feeding to ports is selectable by programming.
2 BRI card
The 2 BRI card contains two Basic Rate access ports, i.e. four ISDN channels. Protocol is compatible
for Euro–ISDN BRI. For S0 application, power feeding to ports is selectable by programming.
TEPRI or PRI card
The PRI card contains one Primary Rate access ports, i.e. thirty ISDN channels. Protocol is compatible
for Euro–ISDN PRI. TEPRI card must be equipped into the last slot of the expansion cabinet. When
programmed as a E1 this card provides up to 30 trunk circuits in any combination of the following:
! Loop start lines
! DID(Direct Inward Dialing)
! Ground start lines
! E & M tie lines or two way DID calling
8 DLI card
The 8 DLI card provides eight DLI ports.
8 SLI card
The 8 SLI card provides eight SLI ports for industry–standard single line telephones and the ability to
provide a loop disconnect signal. Please note that this card does not provide Long Line protection.
6 MWSLI card
The 6 MWSLI card provides six SLI ports for industry–standard single line telephones and the ability
to provide a loop disconnect signal and a message waiting signal. Please note that this card does not
provide Long Line protection.
KDb–DLI, KDb–SLI card
2-4
Chapter 2
Hardware Descriptions
The KDb–DLI board or KDb–SLI board, if installed in a digital keyset connecting to the 008 Basic KSU,
provides a second DLI or SLI port. Only 8 KDbs can be installed in the keysets connected to the basic
KSU.
ITM3 card
The number of the installed ITM3 card is limited to one in the iDCS 100 system.
The ITM3 card supports 8 VoIP channels. These channels are H.323 compliant and are used in
conjunction with either the G.723 or G.729 voice compression protocols. The ITM3 card can be
installed in the universal slot on the Basic KSU.
SVMi-4 Card
The SVMi-4 is a self contained plug in voice mail and auto attendant card for the iDCS 100.
It is designed to meet the demands of the sophisticated voice mail user without sacrificing simplicity.
The SVMi-4 may act as an Auto Attendant system only, a Voice Mail System only or both.
Out of the box the SVMi-4 can handle 2 calls simultaneously. It can be easily upgraded to handle up to
4 calls simultaneously. No external line or power connections and necessary, these are accomplished
directly through phone system
At this time of this writing the memory capacity is about 5 hours, although change in technology will
allow for additional storage as time go on. Only one card is permitted per system and it can be
installed in any universal card slot.
CADENCE (SVMi-8) card
The CADENCE Voice Mail system is a fully integrated Auto Attendant/Voice Mail/Fax System on a
single DCS circuit card. This optional card is designated the SVMi-8 and provides 4 or 8 channels of
communication. Only one card is permitted per system and it can be installed in DCS slot on the
expansion cabinet.
This fully featured self contained system is connected directly to the DCS data bus and communicates
with the DCS Processor. This design means that installation time is minimized, operation is
streamlined and many features can be implemented that are not normally possible with older
conventional stand alone Voice Mail/Auto Attendant systems.
All power to run this self contained system comes from the power supply. Each of the power supply is
rated according to the number of stations it will support. When CADENCE is installed it counts as (8)
eight stations of the PSU rating regardless of the number of Voice Processing Modules installed
2-5
Station Equipment
iDCS SERIES EQUIPMENT
28 Button iDCS Keyset
! 32 character display (2 x 16) with three
associated soft keys and a scroll key
! 28 programmable keys with tri-colored lights
FALC
ON 28
D
Call 1
! Four fixed function keys
Call 2
Scroll
Messag
e
! Terminal Status Indicator
! Built-in speakerphone
Memory
Transfer
Volum
r
HOLD
ANS/R
LS
! Eight selectable ring tones
! UP/DOWN buttons for digital control of
speaker, handset and ringer volumes
Redial
Speake
e
Figure 2–2 28 Button iDCS Keyset
! Desk- or wall-mounted
! Available in dark gray or light gray
18 Button iDCS Keyset
! 32 character display (2 x 16) with three
associated soft keys and a scroll key
! 18 programmable keys with tri-colored lights
FALC
ON 18
D
! Four fixed function keys
Call 1
Scroll
Call 2
Messag
e
! Terminal Status Indicator
! Built-in speakerphone
Memory
Transfer
Volum
r
HOLD
! Eight selectable ring tones
! UP/DOWN buttons for digital control of
speaker, handset and ringer volumes
Redial
Speake
e
ANS/R
LS
Figure 2–3 18 Button iDCS Keyset
! Desk- or wall-mounted Available in dark gray
or light gray
8 Button iDCS Keyset
! 32 character display (2 x 16) with three
associated soft keys and a scroll key
FALCON
! 8 programmable keys with tri-colored lights
8D
Volum
Scroll
e
Call1
! Four fixed function keys
Call2
Messag
e
Transfer
Speake
r
! Terminal Status Indicator
HOLD
! Built-in speakerphone
! Eight selectable ring tones
! UP/DOWN buttons for digital control of
speaker, handset and ringer volumes
! Desk- or wall-mounted
! Available in dark gray or light gray
ANS/R
LS
Figure 2–4 8 Button iDCS Keyset
2-6
Chapter 2
Hardware Descriptions
64 Button iDCS AOM
! 64 programmable keys with red lights
! A maximum of 2 can be assigned to any keyset
to provide additional programmable keys
! A maximum of 4 per DCS System
! Available in dark gray or light gray
Figure 2–5 64 Button iDCS AOM
14 Button iDCS AOM
! 14 programmable keys with red lights
! A maximum of one can be assigned to any
keyset to provide additional programmable
keys
Available in dark gray or light gray
Figure 2–6 14 Button iDCS AOM
2-7
DCS SERIES EQUIPMENT
LCD 24B Keyset
! Built-in speakerphone
! 24 programmable keys (16 with tri-colored LEDs)
! Four fixed function keys
! 32 character display (2 x 16) with three
associated soft keys and a scroll key
! UP/DOWN buttons for digital control of
speaker, handset and ringer volumes
Figure 2–7 LCD 24B Euro Keyset
! Eight selectable ring tones
! Desk- or wall-mounted
! Available in almond or charcoal
STD 24B Keyset
! Built-in speakerphone
! 24 programmable soft keys (16 with tri-colored LEDs)
! Four fixed function keys
! UP/DOWN buttons for digital control of
speaker, handset and ringer volumes
! Eight selectable ring tones per keyset
! Desk- or wall-mounted
Figure 2–8 STD 24B Keyset
! Available in almond or charcoal
STD 12B Keyset
! Built-in speakerphone
! 12 programmable soft keys (16 with tri-colored LEDs)
! Four fixed function keys
! UP/DOWN buttons for digital control of
speaker, handset and ringer volumes
! Eight selectable ring tones per keyset
! Desk- or wall-mounted
! Available in almond or charcoal
Figure 2–9 STD 12B Keyset
2-8
Chapter 2
Hardware Descriptions
6B LCD Model Keyset
! Built-in speakerphone
! 6 programmable keys
! Four fixed function keys
! UP/DOWN buttons for digital control of speaker,
handset and ringer volumes
! Eight selectable ring tones per keyset
! Desk- or wall-mounted
Figure 2–10 6B LCD Model Keyset
Available in almond or charcoal
48 Button AOM
! 48 programmable keys
! Available in almond or charcoal
! One or two can be assigned to any DCS keyset to
provide additional programmable keys
Figure 2–11 48 Button AOM
S-Phone
DS 24S Keyset
! 8 programmable keys with tri-colored lights: Used to
call stations directly, to indicate busy conditions of
other stations, for One Touch dialing and many other
system features.
! Volume Control Keys: Used to set independent levels
for handset, speaker, background music, ring and page
volumes.
! Transfer Key
! Redial Key
! Microphone: For handsfree operation.
! Hold Key
! Speaker Key
! 16 programmable keys with red lights: Used to call
stations directly, to indicate busy conditions of other
stations, for One Touch dialing and many other system
features.
! Speaker: For handsfree operation and ringing.
Figure 2–12A DS 24S Keyset
2-9
DS 24D Keyset
! 8 programmable keys with tri-colored lights: Used to
call stations directly, to indicate busy conditions of
other stations, for One Touch dialing and many other
system features.
! Volume Control Keys: Used to set independent levels
for handset, speaker, background music, ring and page
volumes.
! Transfer Key
! Redial Key
! Microphone: For handsfree operation.
! Hold Key
! Speaker Key
Figure 2–12B DS 24D Keyset
! 16 programmable keys with red lights: Used to call
stations directly, to indicate busy conditions of other
stations, for One Touch dialing and many other system
features.
! Speaker: For handsfree operation and ringing.
! Scroll Key: Used to scroll through displays.
Economic Keyset
! VOLUME CONRTOL KEYS: Used to set independent
levels for handset, speaker, background music, ring
and page volumes.
! TRANSFER KEY
! REDIAL KEY
! MICROPHONE: For handsfree operation.
! HOLD KEY
! SPEAKER KEY
! SPEAKER: For handsfree operation and ringing.
Figure 2–13 Economic Keyset
2-10
Chapter 2
Hardware Descriptions
Door Phone Interface Module (DPIM) & Door Phone
! The DPIM adapts any DLI circuit for use with the door phone unit
! Commonly used to request entry through locked doors (interior or exterior) or as a room
monitoring box
! Provides contact control to be used with customer-provided electric door lock
! Door phone is wall-mounted
! Door phone is weather resistant
Figure 2–14 Door Phone Interface Module
Figure 2–15 Door Phone
Single Line Telephone
! Data Port: selectable to share station extension
or utilize a separate extension
! On hook dialing
! Message Waiting/Ring Indicator
! Desk or wall mounted
! Ring volume control,
! Four available ring tones.
Figure 2–16 Single Line Telephone
! Available in almond and black
This single line telephone set is FCC approved for direct connection to the public telephone
network.
FCC # A3LKOR-24627-TE-T REN 0.9B UL LISTED 19X9 FILE # ETI 8093
Serial Interface Module (SIM)
Provides an RS232 connection required for SMDR and PC programming features connects to any DLI
circuit
2-11
KDb-DLI
This is a small daughterboard that can be installed only in the 12 or 24 button keyset. The KDb-DLI
will provide one additional DLI circuit for the connection of any digital station device such as a
keyset, add-on module or DPIM. This KDb-DLI will only operate when the keyset is connected to an
8 port DLI card so it can use the second B channel. Each port on this card is intended for connection to
one telephone. Connecting multiple telephones to a port may result in incorrect operation or damage
to the card. See the installation manual Chatper 8 for details.
KDb-SLI
This is a daughter board that can be installed only in the 12 or 24 button keyset. The KDb-SLI will
provide one additional SLI circuit for the connection of any standard telephone device. This KDb-SLI
will only operate when the keyset is connected to an 8 port DLI card it can use the second B channel.
Each port on this card is intended for connection to one telephone. Connecting multiple telephones to
a port may result in incorrect operation or damage to the card. See the installation manual Chapter 8
for details.
The circuitry on a KDb-SLI does not provide a loop open disconnect signal or have the
over-voltage protection necessary for OPX operation.
2-12
Chapter 2
Hardware Descriptions
(This page is left blank intentionally.)
3-1
Chapter 3 Specifications
This chapter describes the technical data for the iDCS 100 hybrid/key telephone system as follows.
! Electrical Specifications Key Service Unit
! Interface Cards
! Station Equipment
Electrical Specifications
AC INPUT
220~240VAC, 50Hz, 3.0A
POWER CONSUMPTION (MAX)
140 WATTS MAX
FUSE RATING 2AMP
+5 VOLTS 4.0 AMPS MAX
DC OUTPUT
- 55 VOLTS 1.7 AMPS MAX (for SLT/KTS Feeding
voltage)
- 54 VOLTS 0.4 AMPS MAX (for Battery charge)
Dimensions and Weights
Height(mm)
Width(mm)
Depth(mm)
Weight(kg)
SINGLE CABINET
464
365
148
7.5
TWO CABINETS
464
467
148
12.5
DIGITAL KEYSET
(ALL MODELS)
75
243
220
1.1
ADD–ON
MODULE
71
133
220
0.4
DPIM
120
91
28
0.2
DOOR PHONE
127
99
30
0.2
Environments
OPERATING TEMPERATURE
STORAGE TEMPERATURE
0 – 40 °C
–10.5 – 70 °C
Cable Requirements
EQUIPMENT
CABLE
AWG
MAX FEET
MAX METERS
DIGITAL KEYSETS
1 PR. TWISTED
24
1300
400
ADD–ON MODULES
1 PR. TWISTED
24
1300
400
SINGLE–LINE STATION
1 PR. TWISTED
24
3000
1 KM
DOOR PHONE
2 PR. TWISTED
24
330*
100
3-2
Chapter 3
Specifications
This is the maximum length of the cable between the door phone and the DPIM. The
DPIM can be installed up to 274 cable meters from the KSU.
System Tones
Tone
Frequencies
Cadence
Dial Tone
350 + 440 Hz
CONTINUOUS
Ring Back Tone
440 + 480 Hz
1 sec on + 3 sec off
Busy Tone
480 + 620 Hz
0.5 sec on + 0.5 sec off
DND/No More Tone
480 + 620 Hz
0.25 sec on + 0.25 sec off
Error Tone
480 + 620 Hz
0.25 sec of each tone
Confirmation Tone
350 + 440 Hz
Three bursts of tone 0.1 sec on + 0.1 sec
Transfer/CONF
350 + 440 Hz
0.1 sec on + 0.1 sec off
The details of system tones may vary according to the specifications of each
country.
Keyset LEDs
Condition
LED Color
LED On
LED Off
Off
–
Off
Red/Green
Steady
–
Amber
500 ms
500 ms
Call On Hold
Red/Green
500 ms
500 ms
Ringing C.O. Call
Red/Green
100 ms
100 ms
Green
100 ms
100 ms
Red
100 ms ON/100 ms
OFF for 500 ms
500 ms
Line Idle
Line In Use
Recall
Ringing Internal Call
DND Indication
4-1
Chapter 4 Business Feature Package
This chapter describes various features of the iDCS 100 system as follows.
! System Features
! Station Features
! Display Features
! Sample SMDR Printout without Caller ID
! Sample SMDR Printout with Caller ID
! Sample UCD Report
! UCD Call Statistics
! UCD Agent Statistics
! Sample Traffic Report
! Traffic Report Overview
! Sample Alarm Report
! DECT Service
4-2
Chapter 4
Business Feature Package
SYSTEM FEATURES
Account Code Entry
Forced - Verified
Forced - Not Verified
Voluntary
Account Code Key
All Call Voice Page
Attention Tone
Authorization Codes
Forced
Voluntary
Auto Attendant†
Automatic Hold
Background Music
Cadence–Integrated Voice Mail
Call Activity Display
Call Costing
Caller Identification†
Caller ID
Calling Line Identification (CLI)
Calling ID Features
Name/Number Display
Next Call
Save Caller ID Number
Store Caller ID Number
Inquire Park/Hold
Caller ID Review List
Investigate
Abandon Call List
Caller ID on SMDR
Number to Name Translation
Call Forwarding
All Calls
Busy
No Answer
Busy/No Answer
Forward DND
Follow Me
External
To Voice Mail
Preset Destination
Call Forward Busy (CFB - Networking)
Call Forward No Response
(CFNR - Networking)
Call Forward Unconditional
(CFU - LE Version)
Call Hold
Exclusive
System
Remote
Call Park and Page
Call Pickup
Directed
Groups
Call Waiting/Camp-On
Centrex/PBX Use
Chain Dialing
Class of Service
Common Bell Control
Conference
Add On (5 Party)
Unsupervised
Computer Telephony Integration (CTI)
TAPI 2.1
Customer Set Relocation
Data Security
Database Printout
Dialed Number Identification Service (DNIS)
Direct In Lines
Direct Inward Dialing (DID)
E1/Copper
Day/Night Routing
Busy or Camp-On Option
Direct Inward System Access (DISA)
Direct Trunk Selection
Directory Names
DISA Security
Distinctive Ringing
Door Lock Release (Programmable)
Door Phones
E & M Tie Lines E1/Copper
Executive Barge-In (Override)
With Warning Tone
Without Warning Tone
Trunk Monitor or Service Observing
External Music Interfaces
External Page Interfaces
Flash Key Operation
Flexible Numbering
Hot Line
In Group/Out of Group
Incoming Call Distribution
Incoming/Outgoing Service
Individual Line Control
ISDN Service
Primary Rate Interface (PRI)
Basic Rate Interface (BRI)
Least Cost Routing
Live System Programming
From any Display Keyset
With a Personal Computer
Meet Me Page and Answer
Memory Protection
Message Waiting Indications
Microphone On/Off per Station
Music on Hold—Flexible
Music on Hold—Sources
Off Premises Extensions (OPX)
Operator Group
Overflow
Operator
Station Group
Override Code
Paging
Internal Zones (4)
External Zones (4)
All Internal
All External
Page All
Park Orbits
Primeline Selection
Private Lines
Programmable Line Privacy
Programmable Timers
Recalls
Remote Programming—PC
Ring Modes
Time Based Routing–Plans
Automatic / Manual
Holiday Schedule
Temporary Override
Ring Over Page
Secretary Pooling
Single Line Connections
Speed Dial Numbers
Station List (50 Max)
System List (500 Max)
Speed Dial by Directory
Station Hunt Groups (20)
Distributed
Sequential
Unconditional
Station Message Detail Recording (SMDR)
System Alarms
System Maintenance Alarms
System Directory
Toll Restriction
By Day or Night
By Line or Station
Eight Dialing Classes
Special Code Table
Toll Restriction Override
Tone or Pulse Dialing
Traffic Reporting
Transfer
Screened/Unscreened
Voice Mail Transfer Key
With Camp-On
Trunk Groups (11)
Uniform Call Distribution (UCD)†
UCD Groups
Call Statistics
Agent Statistics
Group Supervisors
Printed Reports
Universal Answer
Voice Mail – Inband Integration
Walking Class of Service
Requires optional hardware and/or software. Ask your dealer for details.
4-3
SYSTEM FEATURE DESCRIPTIONS
ACCOUNT CODE ENTRY
Station users may enter an account code (maximum 12 digits) before hanging up from a call. This
account code will appear in the SMDR printout for that call record. Keyset users may enter this code
using an account code key without interrupting a conversation. Single line telephone users must
temporarily interrupt the call by hook-flashing and dialing the feature access code. Manually entered
account codes can be up to 12 digits long. In some cases users can be forced to enter an account code
and this account code may or may not be verified as described below.
Forced – Verified
When set for this option the user must enter an account code for all outgoing calls. The account code
entered will be verified from a system list of 500 entries. Forced Verified codes can contain the digits
0~9.
Forced - Not Verified
When set for this option the user must enter an account code for all outgoing calls, but the account
code is not verified against the system list. Non verified account codes can contain the digits 0~9, and
#.
Voluntary
In this case account codes are not required to make outgoing calls but may be used if desired. This is
also the method used to assign an account code to incoming calls. These account codes can contain
the digits 0~9, * and #.
ACCOUNT CODE KEY
The account code (ACCT) key can be programmed on any keyset and will appear as a soft key on
display keysets. This key allows the user to enter account codes without interrupting a call.
ALL CALL VOICE PAGE
Users can page all internal and all external paging zones at the same time by dialing the All Page code.
Keysets may be restricted from making or receiving pages in system programming. A maximum of 40
keysets can be programmed in each internal page zone to receive page announcements.
ATTENTION TONE
To get your attention, a brief tone precedes all page announcements and intercom voice calls. There
are separate programmable duration timers for page and voice announce tones.
AUTHORIZATION CODES
Authorization codes are used to give permission to make a call. A maximum of 250 four digit
authorization codes can be either forced or voluntary for iDCS 100. When used, authorization codes
will automatically change the dialing station’s class of service to the level assigned to the
authorization code. Authorization codes may be programmed to print or not print on SMDR.
FORCED
When a station is programmed for forced authorization, the user must always enter this code before
dialing is allowed. The dialed authorization code is verified from the system list of 250 authorization
codes on an iDCS 100.
4-4
Chapter 4
Business Feature Package
VOLUNTARY
Any station user can always enter an authorization code before they begin dialing. The dialed
authorization code is verified from a system list of 250 authorization codes for iDCS 100.
AUTO ATTENDANT
The integrated digital automated attendant feature (AA) provides six ports per AA card and four ports
at MISC2 for simultaneous answering and call processing. A maximum of five cards can be installed
in one system. Each sixteen professionally recorded announcements inform callers of the progress of
their calls. Several examples are the following: “I’m sorry. There is no answer”, “That station is busy”,
and “Invalid Number. Please try again”. A maximum of four minutes of super capacitor backed (100
hours) random access memory (RAM) provide up to 48 customer recordings for announcements or
greetings. Twelve individual announcements (boxes), each with its own dialing options, allow you to
build call routing branches as needed. Callers are routed through the branches by dialing extension
numbers or single digits. This system is compatible with Starmail and Cadence.
Announcements recorded on one AA card can not be played to callers on another AA
card.
AUTOMATIC HOLD
While a keyset user is engaged on an outside (C.O.) call, pressing another trunk key, route key or
CALL button automatically places the call on hold when Automatic Hold is enabled. Pressing TRSF,
CONFERENCE, PAGE or a DSS key always automatically places a C.O. call on hold. Intercom calls
can be automatically held only by pressing TRSF or CONFERENCE. Each keyset user can enable or
disable Automatic Hold.
BACKGROUND MUSIC
Keyset users may choose to hear music through their keyset speakers when optional external sources
are installed. Each user may adjust this level by the use of a volume control program at the selected
keyset.
4-5
CADENCE–INTEGRATED VOICE MAIL
The iDCS 100 can be equipped with Samsung’s proprietary integrated voice mail and auto attendant
card (SVMi Series). It provides 4–8 (2-4) ports of voice processing, expandable in four (two) port
increments. Because it is built into the system it provides such feature as one touch Call Record,
Answering Machine Emulation and Voice Mailbox Administration with interactive keyset displays.
Ask your dealer for literature on Cadence.
CALL ACTIVITY DISPLAY
The iDCS 100 will record and buffer all calling activity within the system. With a Call Activity Display
(CAD) key, the iDCS 100 will display a “snapshot” of the following information:
! The maximum number of ports that have been used
! The maximum number of trunks that have been used
! The maximum number of stations that have been used
! The current number of ports in use
! The current number of trunks in use
! The current number of stations in use
This feature is only available on an iDCS 100 with a LAN module.
CALL COSTING
The iDCS 100 provides programmable call costing tables to calculate the cost of incoming and
outgoing calls. Rates are calculated by the number dialed, and may include surcharges. Display
keysets can be set to show the call duration timer or the call cost. The SMDR report will show either
the call duration or the call cost depending on the station selection. One call handled by multiple
callers will cost each call segment separately.
CALLER IDENTIFICATION
The iDCS 100 supports two methods of identifying an incoming caller depending on the circuit type as
described below.
Caller ID
On an analog, loop start C.O. Line, calling party information is called Caller ID and is available from
the telephone company in two formats, Number only and Name and Number, sometimes called
Deluxe. The iDCS 100 is compatible with both formats. Even if the telephone company only offers the
number only, a name can be attached to the telephone number of frequent callers via the CLIP
translation table.
4-6
Chapter 4
Business Feature Package
Calling Line Identification (CLI)
On ISDN circuits, calling party information is called CLI and is supported on both BRI and PRI type
circuits. The iDCS 100 only supports Number delivery and a name can be attached the telephone
number of frequent callers via the CLIP translation table.
CALLER ID FEATURES
The following features apply to all forms of Caller Identification, however, to make them easier to read
caller identification is referred to as Caller ID.
NAME/NUMBER DISPLAY
Each LCD keyset user can decide if he/she wants to see the name or number in the display.
Regardless of which one is selected to be seen first, the NND key is pressed to view the other pieces of
information.
NEXT CALL
In the event that you have a call waiting or a camped-on call at your keyset, you can press the NEXT
key to display the Caller ID information associated with this next call in queue at your station. Either
the Caller ID name or number will show in the display depending on your selection.
SAVE CALLER ID NUMBER
At any time during an incoming call that provides Caller ID information, you may press the SAVE key.
This saves the Caller ID number in the Save Number feature. Pressing the SAVE number redial key
will dial the Caller ID number. The system must be using Least Cost Routing (LCR) to dial the saved
number.
STORE CALLER ID NUMBER
At any time during an incoming call that provides Caller ID information, you may press the STORE
key. This saves the Caller ID number as a speed dial number in your personal speed dial list. The
system must be using LCR to dial the stored number.
INQUIRE PARK/HOLD
Having been informed that an incoming call is on hold or has been parked, you may view the Caller
ID information before you retrieve the call. This will influence how you choose to handle the call.
CALLER ID REVIEW LIST
This feature allows display keyset users to review Caller ID information for calls sent to their stations.
This list can be from ten to fifty calls in a first in, first out basis. The list includes calls that you
answered and calls that rang your station but that you did not answer. When reviewing this list, you can
press one button to dial the person back. The system must be using LCR to dial the stored number.
4-7
INVESTIGATE
This feature allows selected stations with a special class of service to investigate any call in progress.
If Caller ID information is available for an incoming call, you will know to whom this station user is
speaking. On outgoing calls, you can see who was called. After investigating, you may barge-in on
the conversation, disconnect the call or hang up.
ABANDON CALL LIST
The system has a system-wide abandon call list that stores Caller ID information for calls that rang but
were not answered. The list is accessed using the administrator’s passcode. When reviewing this list,
you are provided options to CLEAR the entry or DIAL the number. You can see the NND key to
toggle between the Caller ID name, number and the date and time the call came in. The system must
be using LCR to dial numbers from the abandon call list. The abandoned call list will store up to 50
unanswered calls on iDCS 100.
Caller ID ON SMDR
The Station Message Detail Records report can be set to include Caller ID name and Caller ID number
for incoming calls. This format expands the printout to 113 characters. Use a wide carriage printer or
an 80 column printer set for condensed print.
NUMBER TO NAME TRANSLATION
The system provides a translation table for 350 entries on iDCS 100. When the Caller ID number is
received, the table is searched. When a match is found, the system will display the corresponding
name.
CALL FORWARDING
This feature allows the user to redirect (forward) incoming calls. The calls can be redirected to the
attendant, a hunt group, voice mail, external number or another station user. If the destination station
is in Do Not Disturb (DND), the calling party will receive DND/Reorder tone. Calls cannot be
forwarded to a door phone.
ALL CALLS
This type of forwarding is not affected by the condition of the station. All calls are immediately
redirected to the designated destination. If desired, the destination station may redirect the call back
to the forwarded station by using the transfer feature. The forwarded station user can continue to
originate calls as usual. If no key is programmed as Forward All, the TRSF key lights steady when a
Forward All condition is set.
BUSY
This feature forwards all calls only when the station set is busy. The station user can originate calls as
usual.
NO ANSWER
This feature forwards calls that are not answered within a preprogrammed time. The user can
originate calls as usual and receive call if present. The timer is programmable on a per-station basis to
allow for differences in individual work habits.
BUSY/NO ANSWER
This feature allows the station user to use both types of forwarding simultaneously, provided the
destinations have already been entered in the usual manner.
4-8
Chapter 4
Business Feature Package
FORWARD DND
This feature works with the Do Not Disturb feature. This allows calls directed to a station in Do Not
Disturb or One Time Do Not Disturb to forward immediately to another destination.
FOLLOW ME
This feature allows the user to forward all calls from another station to the user’s station or change the
forward destination to the user’s current location.
EXTERNAL
This feature forwards C.O. calls to an external number via a central office trunk if allowed by class of
service. Intercom calls may also be programmed to forward to an external number via a central office
trunk. These calls will forward only after the programmable external call forward delay timer expires.
TO VOICE MAIL
Each station may be programmed to allow or deny the ability to forward intercom calls to voice mail.
When denied, valuable message time in the voice mail system can be saved.
PRESET DESTINATION
If desired this feature provides for a permanent (preset) forward no answer destination for each
extension. It can only be programmed by the system technician or system administrator. When any
station does not have FWD/NO-ANSWER set, the call will ring this preset destination if one is
programmed.
Call Forward Busy (CFB) (Networking Enabled only)
This is a different feature from the normal call forward busy and is only used when the forward
destination is in a different node of the network. The operation of the feature is the same as the
normal forward busy where when the forwarded station is busy a calling station will be forwarded to
the forward destination.
Call Forward No Response (CFNR) (Networking Enabled only)
This is a different feature from the normal call forward no answer and is only used when the forward
destination is in a different node of the network. The operation of the feature is the same as the
normal forward no answer where when the forwarded station does not answer after a programmed
amount of time a calling station will be forwarded to the forward destination.
Call Forward Unconditional (CFU)(Networking Enabled only)
This is a different feature from the normal call forward all and is only used when the forward
destination is in a different node of the network. The operation of the feature is the same as the
normal forward all where all calls to the forwarded station will be forwarded to the forward
destination.
CALL HOLD (EXCLUSIVE)
Outside calls can be placed on exclusive hold at any keyset by pressing HOLD twice during a call.
Calls placed on exclusive hold can only be retrieved at the keyset that placed the call on hold.
Intercom calls are always placed on exclusive hold.
4-9
CALL HOLD (SYSTEM)
Outside calls can be placed on system hold at any station. Users may dial the access code or press the
HOLD button. Calls on system hold may be retrieved at any station.
CALL HOLD (REMOTE)
Outside calls can be placed on hold at a remote station. This feature allows calls to be answered at one
keyset and placed on hold at another station. This allows time for the user to proceed to that station
or allows the party that the call was intended for to have that call placed at their station. The call or
trunk button will flash at the remote hold station.
Intercom calls cannot be remote held.
CALL PARK AND PAGE
Each C.O. line has its own park zone. This simple method eliminates confusion and ensures that a
park zone is always available. Pressing the PAGE key parks the call automatically. There are no extra
buttons to press and there is no lost time looking for a free zone.
CALL PICKUP
DIRECTED
With directed call pickup, users can answer calls ringing at any station by dialing a code plus that
station’s extension number or by pressing the feature button and then dialing the extension.
GROUPS
In addition, calls can be picked up from a station group in a similar manner. The group pickup feature
allows users to answer any call ringing within any pickup group. There are 20 pickup groups
available on iDCS 100. A station cannot be in more than one pickup group. To use this feature, station
users either dial the access code or press the assigned feature button followed by the pickup group
number.
CALL WAITING/CAMP-ON
Busy stations are notified that a call is waiting (camped-on) when they receive a tone. The tone is
repeated at a programmable interval. Keysets receive an off-hook ring signal through the speaker and
single line stations receive a tone in the handset. The volume of the camp-on tone can be set by the
station user. Camped-on calls follow Forward No Answer if a Forward No Answer destination has
been set.
Optionally any station can be programmed to automatically camp-on to a busy station instead of
having to press the camp-on button or dial a camp-on code.
CENTREX/PBX USE
CENTREX and PBX lines can be installed in lieu of central office trunks. CENTREX and PBX feature
access codes including the command for hook-flash (FLASH) can be stored under one touch buttons.
Toll restriction programming can ignore PBX or CENTREX access codes so that toll calls can be
controlled when using these services.
4-10
Chapter 4
Business Feature Package
CHAIN DIALING
Keyset users may manually dial additional digits following a speed dial call or chain together as many
speed dial numbers as are required.
CLASS OF SERVICE
The system allows a maximum of 30 station classes of service. Each class of service can be customized
in memory to allow or deny access to features and to define a station’s dialing class. Each station can
be assigned different classes of service for day and night operation.
COMMON BELL CONTROL
The MISC card provides relays that may be programmed to control a customer-provided common bell
or common audible device. These contacts must be programmed as members of a station group and
may provide steady or interrupted closure.
CONFERENCE
The system allows six simultaneous conferences up to 5 parties each.
ADD-ON (5 PARTY)
Any combination of up to five parties (stations or outside lines) can be joined together in an add-on
conference. Parties may be eliminated or added after a conference has been established.
UNSUPERVISE
A station user may set up a conference with two or more outside lines and then exit the conference
leaving the outside lines connected in an unsupervised (trunk to trunk) conference.
This feature requires individual trunk buttons and auto-hold must be enabled.
COMPUTER TELEPHONY INTEGRATION (CTI)
Computer Telephone Integration (CTI) allows integration between the iDCS 100 and a personal
computer system (PC) or a local area network (LAN). Caller ID service is required for TAPI inbound
call applications that use the CID information to display computer records in conjunction with the
presentation of the call to the station on the iDCS 100.
TAPI 2.1
TAPI 2.1 is the method of integrating the iDCS 100 system to a computer. TAPI 2.1 is a LAN based
solution allowing computers to communicate directly to the telephone system over the network
system. This establishes a logical connection rather than a physical connection between telephone and
computer. It eliminates the cost and administrative overhead of connecting every PC to a desktop
phone. It emphasizes third-party call control. (Example: calls can be tracked as they are transferred,
making it more suited to large office applications). TAPI 2.1 can emulate first-party type call control
for the iDCS 100 system, rather than from the telephone as TAPI 2.0 does. For example, to make a call
the iDCS 100, rather than the telephone would dial the phone number, and the call would be then
transferred to the telephone.
4-11
CUSTOMER SET RELOCATION
Customer Set Relocation allows the customer to exchange or swap similar stations in the iDCS 100
without wiring changes. All individual station assignments such as trunk ring, station group, station
COS, station speed dial, button appearances, call forwarding, etc. will follow the Customer Set
Relocation program.
DATA SECURITY
Single line extensions used with modems and facsimile machines can be programmed so that they will
not receive any system-generated tones that would disrupt data transmissions. In addition, these
devices receive DCS C.O. ringing pattern instead of intercom ring pattern. Devices connected to an
SLI card receive a disconnect signal upon termination.
DATABASE PRINTOUT
A copy of the customer database can be obtained by using PCMMC. This information can be directed
to a printer or the PC screen and may be done either on-site or remotely. A complete database or
specific data blocks may be obtained.
DECT Service
The iDCS 100 system provides DECT cordless communications in a single office or throughout a large
commercial or industrial complex. To implement this service, you need BSI card, DBS card and DECT
handsets. Users of this service meet improved overall efficiency, since staff can be reached or make
calls wherever they are.
DIALED NUMBER IDENTIFICATION SERVICE (DNIS)
When DNIS service is provided on an incoming trunk the iDCS 100 can route calls based on the
numbers received.
DIRECT IN LINES
Outside lines may be programmed to bypass the operator(s) and ring directly at any station or group
of stations.
4-12
Chapter 4
Business Feature Package
DIRECT INWARD DIALING (DID) E1/COPPER
The term Direct Inward Dialing or DID refers to four types of digit steered inbound call handling.
These are DID, Both Way DID, Dialed Number Identification service (DNIS and Direct Dial In (DDI).
The iDCS 100 supports all four types as described below.
DID is an inbound only service where multiple telephone numbers are assigned, usually in blocks of
twenty, to a single circuit or small group of circuits. These circuits can be single pair analog circuits
that will terminate on a DID card. The iDCS 100 DID card supports up to four circuits. In addition the
DID circuit can be a channel on a digital E1 service terminating on an iDCS 100 TEPRI card.
Both way DID is a service that combines DID service with normal outbound local telephone service.
This service is provided over E&M tie line circuits. These E&M tie line circuits can terminate on either
the iDCS E&M card or on a channel of a digital E1 circuit on an iDCS TEPRI card.
Dialed Number Identification service (DNIS) is a feature of 800 or 900 type numbers that allows the
number dialed by the caller to be identified in the telephone system by means of a sequence of DTMF
digits (usually four). This service terminates on E&M tie lines. These E&M tie line circuits can
terminate on either the iDCS E&M card or on a channel of a digital E1 circuit on an iDCS TEPRI card.
Direct Dial In (DDI). This is the name given to the above three services when they are provided over
an ISDN PRI circuit.
DIRECT INWARD SYSTEM ACCESS (DISA)
Users can call in on specific DISA lines at any time, input a security code and receive system dial tone.
Users can now place internal calls or if permitted, calls using C.O. lines. The caller must have a tone
dial phone and know his/her DISA security code. DISA lines can be used as both way lines or
incoming only and may be active in day mode, night mode or both. The C.O. lines used for DISA
must have disconnect supervision.
DIRECT TRUNK SELECTION
Each station can be allowed access to or denied access from a trunk or trunk group by access code
when LCR is activated. When restricted, the station user must use a trunk key or a route key.
DIRECTORY NAMES
Each station, station group and C.O. line may be assigned a directory name (maximum 11 characters).
In addition, each personal speed dial number, system speed dial number and entry in the DID
translation table may be assigned a name (maximum 11 characters). These names are displayed
during calls with these ports and in the case of station and speed dial names, can be used to originate
calls. See the Dial by Name feature (Station Features).
DISA SECURITY
Telephone fraud and long distance theft are a serious concern. The iDCS 100 provides a strong DISA
security system. If an incorrect DISA passcode is entered repeatedly (as is the case with “hackers”),
the DISA system can be automatically disabled temporarily. Both the number of incorrect passcode
attempts and the time that DISA is disabled are programmable. In addition, all failed attempts to
access DISA print on SMDR (if provided) with a “DE” DISA error flag.
4-13
DISTINCTIVE RINGING
A user knows the type of call received by the type of ring heard. Outside calls have a single ring
repeated while internal calls have a double ring repeated.
In addition any trunk or station can be programmed to ring a keyset with a predefined ring tone (1–8)
or a single line port with a predefined cadence (1–5) selection. This provides for easy identification of
special lines or extensions that ring your phone.
DOOR LOCK RELEASE (PROGRAMMABLE)
After answering a call from the door phone, users can dial a code to activate a contact closure. This
can be used to operate a customer-provided electric door lock release mechanism. The contact closure
timer is programmable from 100–2500 ms.
DOOR PHONES
The door phone interface module (DPIM) provides for connection of a door phone to a DLI port.
Pressing the button on the door phone produces a distinctive ring (three short rings repeated) at the
assigned station or station group. If not answered within a programmable time, the system releases
the door phone and stops the ringing. Stations may call the door phone directly and monitor the
surrounding areas. Door phones follow the system ring mode plan.
E & M TIE LINES (E1/COPPER)
Your office can be connected to another office with a tie line. Use it to make calls to stations in the
other system. If programming allows, you can access lines in the other system to make outside calls.
Tie line calls can be put on hold, transferred and conferenced in the same way as are other outside
calls. Users accessing the tie line from the other system can get a line in your system and make
outgoing calls. These calls can be controlled by assigning a dialing class to the tie line. Your local
telephone company may use E&M tie lines to provide DID service. In this case these tie lines can be
programmed to follow the DID translation table. See DID. Translated E & M tie line calls have Day
and Night routing capabilities.
EXECUTIVE BARGE-IN (OVERRIDE)
The feature allows specially programmed stations with a barge-in key to override the automatic
privacy of another station or outside trunk. Programming allows barge-in with or without a warning
tone. Stations may also be programmed as “secure” so that they cannot be barged-in on.
WITH WARNING TONE
When the barge-in with tone option is set, the barging-in keyset has its microphone on and the bargedin on station receives an override display. A double burst of warning tone sounds and repeats every
ten seconds. This feature does not work from single line sets.
WITHOUT WARNING TONE
When the barge-in without tone option is set, the barging-in keyset has its microphone muted and the
barged-in on station does not receive an override display. This feature does not work from single line
sets.
TRUNK MONITOR or SERVICE OBSERVING
This feature allows the user who barged-in to retain the trunk call after the original station has hung
up.
4-14
Chapter 4
Business Feature Package
EXTERNAL MUSIC INTERFACES
The iDCS 100 MISC card provides up to two inputs for connecting to customer provided external
music sources. One is located on iDCS 100 base board which is selectable using internal music source
or external music source by shunt pin setting. Another is located on the MISC card.
These sources can be used to provide background music, or any of the varied Music On Hold (MOH)
uses.
EXTERNAL PAGE INTERFACES
The iDCS 100 base board provides one external page output and the iDCS 100 MISC card provides an
additional external page output and three relays which can be used to control the page zone control.
Multiple relays may be assigned to each zone.
FLASH KEY OPERATION
While a user is on an outside line, pressing the FLASH key will flash the central office or PBX. This is
used for custom calling features on C.O. lines or in conjunction with CENTREX/PBX operation.
System programming allows individual flash times for C.O. and PBX lines. When C.O. or PBX flash is
not required, setting the timers for two seconds releases the existing call and returns dial tone to make
a new call.
FLEXIBLE NUMBERING
System programming allows stations to have two, three or four digit extension numbers beginning
with the digit 2 or 3. Default extension numbers begin with 201. Station group numbers can be two or
three digits beginning with the digit 5.
Using digits other than 2, 3 or 5 will require the technician to change other feature access codes in the
system default numbering plan. User guides will need to be modified as these are all written using
the iDCS 100 default numbering plan.
HOT LINE
Stations can be programmed to call a pre-defined station or station group whenever that station goes
off-hook. A hot line delay timer of 0–250 seconds can be programmed to allow sufficient time to make
a different call.
IN GROUP/OUT OF GROUP
Individuals assigned to a station hunt group may temporarily remove their telephones from the group
by pressing the In/Out of Group button providing that there is someone still in the group.
The L version of software has a system wide option to allow all members to log out of a station group.
Stations out of a group will not receive calls to that group but will continue to receive calls to their
individual extension numbers. When desired, the user may put him/herself back into the group by
pressing the button again. Users who do not have this button may dial the access code and the group
desired. A station user is allowed to be in several groups, providing a key and the extender of that
group are assigned for each group on the user’s phone.
4-15
INCOMING CALL DISTRIBUTION
Incoming calls can be assigned to ring a distributed station hunt group. This allows all members of
the group to share the call load.
INCOMING/OUTGOING SERVICE
Outside lines are available for incoming or outgoing service. Programming allows any outside line to
be used for incoming calls only, outgoing calls only or both way service.
INDIVIDUAL LINE CONTROL
Each station in the system can be individually programmed to allow or deny dialing out as well as
allow or deny answering for each outside line.
ISDN SERVICE
PRIMARY RATE INTERFACE (PRI)
The iDCS 100 supports Primary Rate Interface ISDN. PRI allows simultaneous data calls, calling party
and calling line identification, high speed call setup and disconnect are among the benefits of ISDN
calling. The 30+D configuration of ISDN allows call information to be delivered via the data channel
(the “D” of 30B+D) thus leaving the bearer channels (the “B” of 30B+D) available for single use or
combined use to provide a wider bandwidth for data and video.
BASIC RATE INTERFACE (BRI)
The iDCS 100 BRI card supports trunk or station level Basic Rate Interface services (BRI). Trunk or
station BRI use is software programmable. BRI allows simultaneous data calls, called party and
calling number identification, high speed call setup and disconnect are among the benefits of ISDN
calling. The 2B+D configuration of ISDN allows call information to be delivered via the data channel
(the “D” of 2B+D) thus leaving the bearer channels (the “B” of 2B+D) available for single use or
combined use to provide a wider bandwidth for data and video.
LEAST COST ROUTING
Least Cost Routing (LCR) is the ability to automatically select the most cost effective central office
route for the outside number dialed by any station. The iDCS 100 LCR program includes the
following features:
! Option to use or not use LCR or a tenant basis
! Programmable LCR access code
! Digit analysis table 1000 entries each with ten digits for an iDCS 100
! Routing by time of day and day of week (4 time bands per day)
! Routing according to individual station class
! Modify digits table 100 entries for an iDCS 100.
! Flexible trunk group advance timer
! Option to use or not use trunk group advance warning tones
4-16
Chapter 4
Business Feature Package
LIVE SYSTEM PROGRAMMING
The system can be programmed from any display keyset or personal computer without interrupting
normal system operation. There are three levels of programming: technician, customer and station.
The technician level has access to all programs and can allow the customer access to system programs
as needed. Technician and customer access are controlled by different security passcodes.
Programming from a PC requires the PCMMC program.
MEET ME PAGE AND ANSWER
After a user makes a Meet Me Page, the user may remain off-hook to allow the paged party to meet
the user for a private conversation.
MEMORY PROTECTION
In the event that power is lost to the system, all customer data contained in memory is retained by the
use of a “super capacitor” for approximately 7 days. In addition, the PCMMC computer program may
be used to produce a backup copy of the customer data. Additionally, the Smart Media card may be
used to store the system database.
MESSAGE WAITING INDICATIONS
When calling a station and receiving a busy signal or the no answer condition, the caller can leave an
indication that a message is waiting. The message button will flash red at the messaged keyset.
A single line phone will receive a distinctive message waiting dial tone. Five message waiting
indications can be left at any station.
MICROPHONE ON/OFF PER STATION
The microphone can be disabled at any keyset. When the microphone is disabled, the keyset cannot
use the speakerphone, although on-hook dialing and group listening are still possible.
MUSIC ON HOLD—FLEXIBLE
The iDCS 100 allows its music sources to be used in a very flexible manner as follows:
! Each keyset can have a designated music source for playing as Background Music (BGM) through
the keyset speaker.
! Each Station can have a designated music source for playing to callers placed on Exclusive hold at
that station.
! Each Trunk can have a designated music source for playing to callers placed on hold. This setting is
overridden by some of the other settings such as station music on hold, and UCD MOH.
! Each UCD group can have a designated music source to be played while a caller is in queue.
4-17
MUSIC ON HOLD – SOURCES
The iDCS 100 provides for up to six different types of Music on Hold source including silence or
“NONE” as listed below:
! None: No audio is played to the listener
! Tone: A tone or “beep” is repeated at a programmable interval
! Chime: A music chime source located on the Base board is played to the listener.
! External source: An external source connected to a MISC card, such as a digital announcer or radio,
is played to the listener.
! Digital Announcement on AA card: If the system is equipped with an AA card the last port of this
card can be flagged as a MOH source and used to repeatedly play a message recorded on the AA
card to the listener.
! Voicemail Sound File: If the iDCS 100 system has an optional CADENCE card installed, up to 100
custom recorded sound files from the Voice Mail card can be used for MOH sources. For
information on creating the sound files see CADENCE System Administrator Manual-Recording
greeting by number. If you select this option be advised that each VMMOH source requires a
dedicated CADENCE port/channel.
NETWORKING
The iDCS 100 networking feature package allows an iDCS 500 system to be connected together with
some basic feature transparency. The physical connection between the systems is via a proprietary
PRI connection (TEPRI card must be used) and is based on the Q-SIG specification. The following
features are supported between two networked systems.
Call Completion, Busy Station (CCBS) also known as Callback or Busy Station Callback. When a
station in one system calls a station in another system across the network link and the destination
station is busy the calling station can set a Callback to the busy station. When the busy station
becomes idle the system will notify the callback originating station by ringing that station and when
the originating station answers, the system will call the destination station.
Call Completion, No Response (CCNR) also known as Callback or No Answer Callback. When a
station in one system calls a station in another system across the network link and the destination
station does not answer the calling station can set a Callback to the called station. When that station
indicates the user is present by becoming busy then idle the system will notify the callback originating
station by ringing that station and when the originating station answers, the system will call the
destination station.
Call Forward Busy (CFB). This is a different feature from the normal call forward busy and is only
used when the forward destination is in a different node of the network. The operation of the feature
is the same as the normal forward busy where when the forwarded station is busy a calling station
will be forwarded to the forward destination.
Call Forward No Response (CFNR). This is a different feature from the normal call forward no
answer and is only used when the forward destination is in a different node of the network. The
operation of the feature is the same as the normal forward no answer where when the forwarded
station does not answer after a programmed amount of time a calling station will be forwarded to the
forward destination.
4-18
Chapter 4
Business Feature Package
Call Forward Unconditional (CFU). This is a different feature from the normal call forward all and is
only used when the forward destination is in a different node of the network. The operation of the
feature is the same as the normal forward all where all calls to the forwarded station will be forwarded
to the forward destination.
Forward External. This feature operates in the same manner as a non networked system with the
exception that, because calls across a network link are trunk calls, network calls do not follow the ICM
FWD EXT ON/OFF setting in MMC 210. It is therefore suggested that this setting be set to ON in a
networked switch to avoid confusion in operation between networked and non networked calls.
Call Intrusion (Barge In). This feature operates in the same manner as in a non networked switch.
Call Offer/Call Waiting (Camp On). This feature operates in the same manner as in a non networked
switch. When a called station is busy the caller can press a camp on key and appear as a ringing call
on the second call button. The Auto camp on feature will not work on calls across a network link if set
to ON in MMC 110.
Call Transfer. Calls answered in one network node can be transferred to a station or station group in
another network node.
Transfer Retrieve. Calls on Transfer Hold during a screened transfer can be retrieved by pressing the
call button for that call.
Transfer Recall. Calls transferred across a network link will recall to the transferring station after the
originating systems transfer recall timer expires. After recalling, if not answered prior to that systems
attendant recall timer expiring, the call will recall to that systems designated operator group.
Attendant recalls will not recall to a ‘Centralized Attendant’.
DID with Pass Through. Incoming DID, DNIS or DDI calls can be routed through one switch across a
network link to be processed by the DID table of the destination switch.
Do Not Disturb (DND). This feature operates in the same manner as in a non networked switch. There
is an option in MMC 823 to determine the type of DND tone sent across the network link.
Caller ID. Caller ID in its various forms that are currently available (Analog CID Name and Number,
ANI Number, PRI Name and Number and BRI number) will be transported across the network link
with the original call.
Centralized Attendant. This feature basically allows a user in any switch to dial “0” and ring at the
designated Central attendant group. Each system on the network requires its own designated
attendant group for local usage, recalls and the like.
Intercom Calling/Uniform dialing plan. Station to station and station to group calls can be made across
the network link without having to dial an access code for a call within the network. LCR can also be
programmed to route calls across a network link to access local trunks in another networked system.
Centralized Voice Mail with Message Waiting Lights. This feature will only operate with Cadence
and/or SVMi voicemail systems only. Users in one node can call forward (CFNR, CFB & CFU) to the
Cadence group in a different switch and messages left in that switch will be indicated on the VMSG
key in the origination switch. Messages can be returned to the Cadence or SVMi voice mail system.
OFF PREMISES EXTENSIONS (OPX)
A single line (tip and ring) extension from an 4SLI card may be connected to telephone companyprovided OPX circuits to remote locations. 8SLI cards and KDb-SLIs do not support off premises
extensions.
4-19
OPERATOR GROUP
The operator group can contain 32 stations to answer incoming calls. Calls to this group can be set for
distributed, sequential or unconditional ringing. Operators can use the In/Out of Group feature to
meet flexible operator requirements. Operator groups are selectable per ring plan.
OVERFLOW
OPERATOR
When calls ringing a operator group go unanswered, they can overflow to another destination after a
programmed period of time. The operator group has its own timer. The overflow destination can be a
station or station group.
STATION GROUP
When calls ringing a station group go unanswered, they can overflow to another destination after a
programmed period of time. Each station group has its own timer. The overflow destination can be a
station or station group.
OVERRIDE CODE
This feature allows users to make emergency outside calls from a station that has a forced code such as
Account code or authorization code enabled but without requiring them to enter a forced code. The
basis of this feature is an override code table containing 5 entries of up to 11 digits each. The iDCS 100
will examine digits that are dialed from a station to see if they match any entry in the Emergency
Number table. If the digits match the table, the system will process the call without requiring a forced
code.
PAGING
System software allows the use of four internal and four external paging zones. Stations can page any
individual zone, all internal zones, all external zones or all zones simultaneously. Using system
programming, each station may be allowed or denied the abilities to make and/or receive page
announcements to any zone or combination of zones.
PARK ORBITS
The system has 10 park orbits (0–9). These orbits can be used to park calls prior to paging and allows
the call to be retrieved by dialing a park code plus the orbit number. Calls parked in this manner can
also be retrieved by dialing the park pickup code (10) plus the station or trunk number. This feature is
in addition to Call Park and Page.
PRIME LINE SELECTION
Any station can be programmed to select a specific line, trunk group, telephone number, station or
station group when the handset is lifted or the speaker key is pressed (same as Hot Line feature).
PRIVATE LINES
For private line use, stations can be prevented from dialing and/or answering any line.
PROGRAMMABLE LINE PRIVACY
Each outside line can be programmed to ignore the automatic line privacy. This allows up to four
other parties to join your conversation by simply pressing the line button. This is similar to 1A2 key
telephone operation.
4-20
Chapter 4
Business Feature Package
PROGRAMMABLE TIMERS
There are over 50 programmable system timers to allow each installation to be customized to best fit
the end user’s application.
RECALLS
Calls put on hold, transferred or camped-on to any station will recall to the originating station if not
answered within a programmable time. A recall that goes unanswered for the duration of the
attendant recall timer will recall to the system operator group. Hold, transfer, camp-on and attendant
recalls have individual programmable timers. Calls recalling to buttons with tri-colored LEDs will
flash amber.
REMOTE PROGRAMMING—PC
Remote programming allows the technician to access the system database from a remote location for
the purpose of making changes to the customer data. Customer-provided modems and a PC using an
optional software package will be needed to implement this feature.
RING MODES
TIME BASED ROUTING – PLANS
Each C.O. line can be programmed to ring at any station or station group. Each line can be assigned a
ring destination based on six (6) different ring plans based on time of day and the day of the week.
AUTOMATIC / MANUAL
Ring destinations will automatically change based on time of day and day of week. At any time the
system can be manually forced into a specific ring plan. It will remain in this ring plan until manually
taken out.
HOLIDAY SCHEDULE
The system has a table of 20 dates that are used to define holidays. On a date designed as a holiday
the system will remain in a ring plan for that calendar day providing the system was already in night
service. This feature will override the ring plan time table.
TEMPORARY OVERRIDE
At any time the system can be forced into a specific ring plan for a temporary period of time until the
next scheduled ring plan automatically takes effect.
RING OVER PAGE
Any outside line can be programmed to ring over a customer-provided paging system. Outside lines,
door phones and station groups may ring over page in the day or night mode.
4-21
SECRETARY POOLING
Each keyset may be defined as an executive (BOSS in programming) or a secretary (SEC in
programming) in system programming. Each executive can have up to four secretaries and each
secretary can have up to four executives. These arrangements are known as executive/secretary
pools. There can be multiple pools in a system. When an executive is in DND, all calls to the
executive ring the first secretary assigned to that executive; if that secretary is busy, the call hunt to the
next available secretary assigned to that executive. If the secretary must communicate with the
executive while he/she is in DND, pressing the corresponding executive button on the secretary’s
keyset results in an Auto Answer intercom call being made to the executive (providing the executive is
free). The iDCS 100 has a system wide option to allow the stations to ring rather than auto announce
the executive secretary calls. A station can only be the executive of one secretary pool. In addition, a
station cannot be in more than one pool.
SINGLE LINE CONNECTIONS
Single line ports allow connection of a variety of single line telephones plus facsimile machines,
answering machines, loud bells, computer modems, cordless phones and credit card machines. When
connecting customer-provided equipment to these extensions, compatibility should be checked out
before purchase to ensure correct operation. Central office ring cadence can be selected for SLT
stations. This is helpful when optional devices cannot detect iDCS 100 intercom ring cadence.
SPEED DIAL NUMBERS
A library of 1500 speed dial numbers may be allocated as needed for iDCS 100. The system list can
have up to 500 numbers and each station can have up to 50 numbers. Speed dial numbers are
assigned in blocks of ten. Each speed dial number may contain up to 24 digits.
SPEED DIAL BY DIRECTORY
The iDCS 100 system provides the user with the ability to look up a speed dial number and place the
call. There are three speed dial selections: personal, system and station. This feature requires a display
keyset.
STATION HUNT GROUPS
System programming allows up to 20 station hunt groups on an iDCS 100. One of three ring
patterns—sequential, distributed and unconditional—is available for each group. Each unconditional
group may contain a maximum of 32 stations and each sequential and distributed group may contain
a maximum of 48 stations. A station may be assigned to more than one group. Each station group has
its own recall timer for calls transferred to that group.
STATION MESSAGE DETAIL RECORDING (SMDR)
The system provides records of calls made, received and transferred. Connecting a customerprovided printer or call accounting system will allow collection of these records. Each call record
provides the following details: station number, outside line number, start date, start time, duration of
call, digits dialed (maximum 18) and an account code if entered. The system may print a header
followed by 50 call records per page or send continuous records with no header for use with a call
accounting machine. See the sample printouts.
The SMDR format contains many options that allow it to be customized for a company’s individual
needs. Options to print include incoming calls, outgoing calls, in and out of group status, change in
DND status and authorization codes.
i
4-22
Chapter 4
Business Feature Package
SYSTEM ALARMS
A DISA alarm will warn the customer if the DISA security system has been triggered by too many
incorrect password attempts. The alarm can ring any station or group of stations and show an
appropriate display at the assigned stations.
SYSTEM MAINTENANCE ALARMS
The iDCS 100 continuously performs internal system diagnostics. When either a major or minor fault
is detected the system can ring stations with an ALARM KEY assigned. The keyset display shows
information that includes the description, location and date and time stamp for each alarm.
A log of 100 alarms are stored in a buffer and can be reviewed at a display keyset or sent to a printer
(see sample Alarm Report in section 4.11 of this document).
System Maintenance Alarms are only available and with a LAN module.
SYSTEM DIRECTORY
Each station, station group and outside line can have an 11 character directory name. This name will
appear on keyset displays to provide additional information about lines and stations.
TOLL RESTRICTION
There are 250 allow and 250 deny entries of 11 digits each. Each of these entries can apply to dialing
classes B, C, D, E, F and G. Expensive 976, 1-900, 411 and operator-assisted calls, as well as specific
area and office codes, can be allowed or denied on a per-class basis. Class A stations have no dialing
restrictions and Class H stations cannot make outside calls.
Any outside line may be programmed to follow station toll restriction or follow the toll restriction
class assigned to it. Each station and trunk can have a day dialing class and a night dialing class.
SPECIAL CODE TABLE
A Special Code Table of ten entries (four digits each) allows use of telephone company features such as
CID blocking (*67) or call waiting disable (*70) without interference to toll restriction or LCR. The
Special Code table allows use of these custom calling features on a per call basis.
TOLL RESTRICTION OVERRIDE
Program options allow system speed dial numbers to follow or bypass a station’s toll restriction class.
In addition, users may make calls from a toll restricted station by using the walking class of service or
authorization code feature.
4-23
TONE OR PULSE DIALING
Outside lines can be programmed for either tone or pulse dialing to meet local telephone company
requirements.
TRAFFIC REPORTING
The iDCS 100 system can store peg counts for various types of calls. These peg counts can be printed
on-demand, daily, hourly, or up to three separate programmable shifts. The report includes statistics
for each trunk, trunk group, station, station groups and page announcements. For more details and
explanations see sections 4.9 and 4.10 of this document.
Traffic Reporting is only available with a LAN module.
TRANSFER
System operation permits station users to transfer calls to other stations in the system. T ransfers can
be screened, unscreened or camped-on to a busy station.
TRUNK GROUPS
Outside lines can be grouped for easy access by dialing a code or pressing a button. There are 11 trunk
groups available for iDCS 100.
UNIFORM CALL DISTRIBUTION (UCD)
UCD is used whenever the user expects to have more ringing calls than people to answer them. It
prevents callers from receiving busy signals or lengthy delays before answering. Callers reaching a
busy station group are held in queue for an available agent. First and second announcements reassure
the caller until an agent becomes free. Programmable automatic logout removes a station from the
group if a call is placed to an unattended station, thus preventing unanswered calls. A wrap-up timer
prevents calls to a station for a programmable period of time to allow the agent to finish up work
associated with the call.
Requires optional hardware. Ask your dealer for details.
UCD GROUPS
The UCD group option allows callers in queue at a UCD group to be temporarily diverted to an
announcement device and then placed back in the queue. A wrap-up timer will allow agents to
complete paperwork before receiving the next UCD call.
CALL STATISTICS
UCD supervisor positions using a display keyset can monitor the number of calls in queue, the time
that the oldest caller has been waiting, the total number of calls received for the current day and the
average time a caller waits to be answered.
AGENT STATISTICS
UCD supervisor positions using a display keyset can monitor the number of agents in a group and
how many agents are currently logged in. Each station’s status can be reviewed for the number of
calls answered and the average call length of the current day.
4-24
Chapter 4
Business Feature Package
GROUP SUPERVISORS
Multiple supervisors can be assigned to each group or one station can be given supervisor status for
multiple groups. The group supervisor (using a display keyset) can add and delete agents in real time
from the group to handle the workload.
PRINTED REPORTS
Agent supervisors may run printed reports to a customer-provided printer, showing the data available
on the supervisor displays.
UNIVERSAL ANSWER
Station users may dial the Universal Answer code or press the UA key to answer any outside lines
programmed to ring the UA device. The UA device can be a station, group of stations, common bell or
ring over page.
VOICE MAIL – INBAND INTEGRATION
The iDCS 100 system uses DTMF tones (inband signaling) to communicate with any compatible voice
mail system. Stations can call forward to a voice mail system. When answered, the system will send
DTMF tones routing the caller directly to the called station user’s mailbox. Keyset users can press one
button to retrieve messages from the voice mail system. A Voice Mail Transfer key permits keyset
users to easily transfer a caller directly to an individual voicemail box without navigating through
menus.
Although most voice mail systems will work with the iDCS 100, the system data has
default values set to work with the Starmail Voice Processing System. They may need
to be changed if you are using another system.
WALKING CLASS OF SERVICE
This feature allows users to make calls or use features from a station that is restricted. The users may
either use the WCOS feature code or the authorization code feature. Both methods change the class of
service to correspond with the station passcode or authorization code that is dialed. After the call is
completed, the station returns to its programmed class of service.
4-25
STATION FEATURES
ADD-ON MODULE
PROGRAMMABLE KEYS
APPOINTMENT REMINDER
PROGRAMMED STATION MESSAGES
AUTOMATIC HOLD
PROTECTION FROM BARGE-IN
AUTOMATIC PRIVACY
PULLOUT DIRECTORY TRAY
BACKGROUND MUSIC
PULSE TO TONE SWITCH OVER
BUSY STATION CALLBACK
REDIAL
BUSY STATION INDICATIONS (BLF)
AUTO RETRY
CALL FORWARDING
LAST NUMBER
CALL LOGS
MEMO REDIAL
SAVE NUMBER
CALL PICKUP
DIRECT STATION SELECTION (DSS)
REMOTE HOLD
DO NOT DISTURB (OVERRIDE)
RING MODES
DO NOT DISTURB (PROGRAMMABLE)
AUTO ANSWER
DOOR LOCK RELEASE
RING–EIGHT TONE CHOICES
EXCLUSIVE HOLD
VOICE ANNOUNCE
GROUP LISTENING
RINGING PREFERENCE
HEADSET OPERATION
SPEAKERPHONE
HEARING AID COMPATIBLE
STATION LOCK
LINE QUEUING WITH CALLBACK
TRI-COLORED LIGHTS
LINE SKIPPING
VOLUME SETTINGS
LOUD RINGING INTERFACE
HANDSET
MESSAGE WAITING LIGHT/INDICATION
BGM
MUTE MICROPHONE/HANDSET
RINGING
OFF-HOOK RINGING
PAGING
OFF-HOOK VOICE ANNOUNCE (STANDARD)
SPEAKER
OFF-HOOK VOICE ANNOUNCE (EXECUTIVE)
ONE TIME DO NOT DISTURB
OFF-HOOK RING
WALL-MOUNTABLE KEYSETS
ONE TOUCH DIALING KEYS
ON-HOOK DIALING
Requires optional hardware and/or software. Ask your dealer for details.
STATION FEATURE DESCRIPTIONS
ADD-ON MODULE
32 BUTTON AOM
The 32-button add-on module (AOM) adds to the capability of any keyset. The 32 programmable
buttons with red buttons can be used for feature keys, DSS/BLF keys or one touch speed dial buttons.
Because this AOM has a microphone and a speaker it can be used to provide executive off hook voice
announce or as a stand alone unit whenever a handset and dial pad are not required.
64 BUTTON MODULE
The 64-button module adds to the capability of any keyset. Up to four 64-button modules can be
added to each keyset. The 64 programmable red LED buttons with red LED can be used for feature
keys, DSS/BLF keys or one touch speed dial buttons. A maximum of 5 can be installed on an iDCS 100
system.
4-26
Chapter 4
Business Feature Package
APPOINTMENT REMINDER
Keysets with an alarm key can be used like an alarm clock. When programmed for a specific time, the
keyset will sound a distinctive ring to remind the user of meetings or appointments. Alarms can be
set for “today only” or for every day at the same time. Up to three alarms may be set at each keyset.
Display keysets can also show a programmed message when the alarm rings.
AUTOMATIC HOLD
Station users can enable or disable automatic hold at their keysets. While a user is engaged on an
outside (C.O.) call, pressing another trunk key, route key or CALL button automatically puts the call
on hold when this feature is enabled. Pressing TRSF, CONFERENCE, PAGE or a DSS key will always
automatically place the call on hold. This type of automatic hold is not a user-selectable option.
AUTOMATIC PRIVACY
All conversations on outside lines and intercom calls are automatically private. The privacy feature
can be turned off on a per-line basis.
Intercom calls cannot be automatically held.
BACKGROUND MUSIC
Keyset users may choose to hear music through their keyset speakers when optional external sources
are installed. Each user may adjust this level by the use of a volume control program at the selected
keyset.
BUSY STATION CALLBACK
When reaching a busy station, callers may request a callback by pressing one button or dialing a code.
The system rings the caller back when that station becomes idle (a system-wide maximum of 100
callbacks are allowed at one time including busy station and busy trunk).
BUSY STATION INDICATIONS (BLF)
DSS/BLF keys may be assigned to any keyset or add-on module. These buttons will be off when the
station is idle, light red when that station is in use and flash distinctively when that station is in the
DND mode.
CALL FORWARDING
Station users can forward internal and outside calls to other destinations immediately (Forward All),
when busy (Forward Busy) or if not answered in a programmable number of seconds (Forward No
Answer). These forward destinations can all be different. Once a destination has been programmed,
it can be turned on and off with a programmable key. Forward All takes priority over Busy and No
Answer conditions.
In addition to the three usual methods of forwarding described above, a fourth option called Follow
Me is available. This option allows a station user to set a Forward All condition from his/her station
to another station while at the remote station. To display the Follow Me condition, the TRSF key lights
steady red at the station that is forwarded. The TRSF key also lights if Forward All is set and no key is
programmed for Forward All.
Keyset users can be given an external call forward button to forward their calls to an external phone
4-27
number. Each outside line may be programmed to either follow or ignore station call forwarding. A
per-station option controls whether internal calls forward to voice mail or not. Single line telephones
must have the system administrator program this feature for them.
CALL LOGS
With the call log feature, a display keyset user can review up to 50 of the last incoming calls from the
Caller ID review list or up to 50 of the last external telephone numbers that were dialed.
The numbers can be viewed, stored and/or dialed using the associated soft keys. LCR must be
enabled for dialing and storing numbers from the CID review list. Optional hardware and/or
software may be needed for Caller ID.
Call Logs are only available with a LAN module.
CALL PICKUP
With directed call pickup, a user can answer calls ringing at any station by dialing a code plus that
extension number. The group pickup feature allows the user to answer any call ringing within a
pickup group. Pickup keys may be customized with extenders to allow pickup from a specific station
or pickup group. The iDCS 100-M version software has 20 programmable pickup groups and the iDCS
100.
DIRECT STATION SELECTION (DSS)
Programmable keys can be assigned as DSS keys and associated with extension numbers.
Users press these keys to call or transfer calls to the assigned stations.
DO NOT DISTURB (OVERRIDE)
The DND Override feature allows a keyset with a DND Override key (DNDO) and the appropriate
class of service to override the DND setting at a called keyset. This will allow a user to go into DND
while waiting for an important call and have that call transferred to them via a screened transfer from
a station (for example the users secretary) with a DNDO key.
DO NOT DISTURB (PROGRAMMABLE)
The Do Not Disturb (DND) feature is used to stop all calls to a station. System programming can
allow or deny use of the DND feature for each station. Parties calling a station in DND will receive
reorder tone. When in DND mode, calls may be forwarded to another destination. See Forward DND
option. A keyset without a DND button can activate DND via the feature access code. The ANS/RLS
key will flash at 112 ipm (rapidly) when DND is set. There is a programmable option to allow a C.O.
line to override DND at its ring destination if that destination is a single station.
DOOR LOCK RELEASE
Stations programmed to receive calls from a door phone can dial a code to activate a contact closure
for control of a customer-provided electronic door lock.
EXCLUSIVE HOLD
Pressing HOLD twice will hold a call exclusively at a station so no other station can pick up that call.
Intercom calls are automatically placed on exclusive hold.
4-28
Chapter 4
Business Feature Package
GROUP LISTENING
This feature allows users to turn on the speaker while using the handset. It allows a group of people
to listen to the distant party over the speaker without the microphone turned on.
HEADSET OPERATION
Every keyset can be programmed to allow the use of a headset. In the headset mode, the hookswitch
is disabled and the ANS/RLS key is used to answer and release calls. Keyset users may turn headset
operation ON/OFF by keyset programming or more easily by pressing the headset ON/OFF key. The
headset key lights steady red when the keyset is in headset mode. The ANS/RLS key lights if headset
mode is activated by keyset programming only.
HEARING AID COMPATIBLE
All iDCS 100 keysets are hearing aid compatible as required by Part 68 of the FCC requirements.
LINE QUEUING WITH CALLBACK
When the desired outside line is busy, the user can press the CALLBACK key or dial the access code to
place his/her station in a queue. The user will be called back when the line is available (a maximum
of 100 callbacks are allowed system-wide at one time including busy station and busy trunk).
LINE SKIPPING
When the user is talking on an outside line and the automatic hold feature is turned off, he/she may
press an idle line key and skip to that line without causing the previous call to go on hold.
LOUD RINGING INTERFACE
The MISC board has 3 relays that can be programmed to provide a dry contact closure for control of a
customer provided loud ringing device. Any of these relays can be programmed to operate with a
specific station or station group.
MESSAGE WAITING LIGHT/INDICATION
When a message indication is left at a keyset, the MESSAGE button will slowly flash red. Single line
telephones will receive a distinctive dial tone to notify them that a message is waiting. Message
waiting indications can be left for any station or group of stations.
MUTE MICROPHONE/HANDSET
Any keyset user can mute the keyset’s handset transmitter by pressing the MUTE key. In addition,
keyset users can also mute the keyset microphone while the keyset is in speakerphone mode.
4-29
OFF-HOOK RINGING
When a keyset is in use, the system will provide an off-hook ring signal to indicate that another call is
waiting. The ring signal is a single ring repeated. The interval is controlled by a system-wide timer.
Single line stations will receive a tone burst through the handset receiver instead of a ring.
OFF-HOOK VOICE ANNOUNCE (EXECUTIVE)
A keyset associated with an add-on module may receive an executive off-hook voice announcement
while on another call. The called keyset user may reply handsfree without interrupting the call in
progress. Only keysets with an off-hook voice announce button (OHVA) can off-hook voice announce
to keysets with AOMs.
OFF-HOOK VOICE ANNOUNCE (STANDARD)
Keysets may receive a voice announcement while on another call. The calling station must have an
OHVA key. When transferring a call to a busy keyset or while listening to busy signal, the station user
can press the OHVA key to make an OHVA call to the busy keyset. If the called keyset is in the DND
mode, it cannot receive OHVA calls.
ONE TIME DO NOT DISTURB
The Do Not Disturb (One Time) feature is used to stop all calls to a station when the user is on an
outside line and does not want to be disturbed for the duration of the call. Upon completion of the
call, DND is canceled and the station is returned to normal service. This feature requires a
programmed button.
ONE TOUCH DIALING KEYS
Frequently used speed numbers can be assigned to one touch dialing keys for fast accurate dialing.
ON-HOOK DIALING
Any keyset user can originate calls without lifting the handset. When the called party answers, the
user may speak into the microphone or lift the handset for more privacy.
PROGRAMMABLE KEYS
LCD 24B and STD 24B keysets have 24 programmable keys, LCD 12B and Basic 12B keysets have 12,
and 7B keysets have 12. Each key can be programmed for more than 25 different uses to personalize
each phone. Examples of keys include individual outside line, individual station, group of lines,
group of stations and one touch speed dial buttons. Using these keys eliminates dialing access codes.
The following feature keys have extenders that make them more specific: SPEED DIAL, SUPERVISOR,
PAGE, DSS, DIRECTED PICKUP, GROUP PICKUP, DOOR PHONE, BOSS, PROGRAMMED
MESSAGE, IN AND OUT OF GROUP, FORWARD and VOICE MAIL TRANSFER. The extender can
be a station, a group or another identifying number.
PROGRAMMED STATION MESSAGES
Any station may select one of 20 to be displayed at a calling party’s keyset. Ten messages are factoryprogrammed but may be reprogrammed.
The calling party must have a display keyset to view these messages.
4-30
Chapter 4
Business Feature Package
PROTECTION FROM BARGE-IN
Each station can be programmed as secure or not secure. Secure stations cannot be barged-in on. A
station that is not secure cannot be barged-in on when talking to a secure station.
PULLOUT DIRECTORY TRAY
A pullout directory tray is conveniently located beneath all keysets. It is used to record station
directory names and speed dial numbers.
PULSE TO TONE SWITCHOVER
When dialing a number on a dial pulse network, a station user can dial # and the DCS system will
begin to send DTMF.
REDIAL
There are three types of external redial available to all station users. Each type can redial up to a
maximum of 18 digits.
! AUTO RETRY— When an outside number is dialed and a busy signal is received, the auto retry
feature can be used to reserve the outside line and automatically redial the number for a
programmable number of attempts (available to keyset users only).
! LAST NUMBER— The most recently dialed number on a C.O. line is saved and may be redialed by
pressing the redial key or dialing the LNR access code.
! MANUAL RETRY with LNR— When you make an outside call and receive a busy signal you can
press the LNR key to redial the same number again. This operation can be manually repeated for a
limited number of attempts as defined by system programming (available to keyset users only).
! SAVE NUMBER— Any number dialed on a C.O. line may be saved for redial at a later time.
REMOTE HOLD
When you wish to place a call on hold at another station, press TRSF and dial the station number (or
press the appropriate DSS key). Press the HOLD key. This will place the call on system hold on an
available CALL button or Line Key at the remote station.
4-31
RING MODES
Each keyset user can select one of three distinct ways to receive intercom calls. The phone can
automatically answer on the speakerphone, voice announce through the speaker or receive ringing.
When the ring mode is selected, keyset users can choose one of eight distinct ring tones. Forced Auto
Answer is invoked by the calling station and is controlled by the calling station’s class of service.
RINGING PREFERENCE
Lifting the handset or pressing the speaker button automatically answers a call ringing at the keyset.
Using this method, users are assured of answering the oldest call first. When ringing preference is
turned off, the user must press the flashing button to answer. Users may answer ringing lines in any
order by pressing the flashing button.
SPEAKERPHONE
DCS LCD 24B and DCS LCD 12B keysets have built-in speakerphone. The speakerphone enables calls
to be made and received without the use of the handset. All iDCS keysets are speakerphones. The
iDCS 28 Button and the iDCS 18 Button can have a Full Duplex Speakerphone Module added.
STATION LOCK
With a programmable personal station passcode, any keyset or single line station can be locked and
unlocked to control use of each telephone. There are two lock options: 1=LOCKED OUTGOING and
2=LOCKED ALL CALLS. See the following table for more details.
TRI-COLORED LIGHTS
LCD 24B and STD 24B keysets have 16 keys equipped for tri-colored LED indications (green, red and
amber). LCD 12B and Basic 12B models have six of these keys and 7 button keysets have three. To
avoid confusion, your calls always light green, other calls show red and recalls light amber.
VOLUME SETTINGS
Each keyset user may separately adjust the volume of the ringer, speaker, handset receiver,
background music, page announcement and off-hook ring tone.
WALL-MOUNTABLE KEYSETS
Each keyset, add on module and 64 button module can be wall mounted by reversing the base wedge.
The newest base wedge may not fit all wall mounting scenarios so in these cases the original wall
mount/base wedge unit should be used.
4-32
Chapter 4
Business Feature Package
DISPLAY FEATURES
ACCOUNT CODE DISPLAY
ENHANCED STATION PROGRAMMING
CALL DURATION TIMER
IDENTIFICATION OF RECALLS
CALL FOR GROUP IDENTIFICATION
IDENTIFICATION OF TRANSFERS
CALL PROCESSING INFORMATION
MESSAGE WAITING CALLER NUMBER
CALLER ID INFORMATION
OUTSIDE LINE IDENTIFICATION
CALLING PARTY NAME
OVERRIDE IDENTIFICATION
CALLING PARTY NUMBER
PROGRAMMED MESSAGE DISPLAY
CONFERENCE INFORMATION
SOFT KEYS
DATE AND TIME DISPLAY
STOPWATCH TIMER
DIALED BY NAME
DIALED NUMBERUCD SUPERVISOR DISPLAYS
DISPLAY FEATURE DESCRIPTIONS
ACCOUNT CODE DISPLAY
Account codes are conveniently displayed for easy confirmation. If entered incorrectly, users may
press the ACCOUNT key again and reenter the account code.
CALL DURATION TIMER
The system can automatically time outside calls and show the duration in minutes and seconds.
Station users may manually time calls by pressing the TIMER button.
CALL FOR GROUP IDENTIFICATION
When a call is made to a station group, the display shows [CALL FOR GROUP] and the user’s group
number. These calls can be answered with a different greeting than calls to the user’s extension
number.
CALL PROCESSING INFORMATION
During everyday call handling, the keyset display will provide information that is helpful and in some
cases invaluable. Displays such as [CALL FROM 203], [TRANSFER TO 202], [701: RINGING],
[TRANSFER FM 203], [708 busy], [Camp on to 204], [Recall from 204], [Call for 501], [message from
204] and [FWD ALL to 204] keep users informed of what is happening and where they are. In some
conditions, the user is prompted to take action and in other cases the user receives directory
information.
CALLER ID INFORMATION
Caller ID information is dependent on the use of display keysets. The following list explains the
displays that are used with Caller ID.
NAME/NUMBER DISPLAY
Each display keyset user can decide if he/she wants to see the Caller ID name or Caller ID number in
the display. Regardless of which one is selected to be seen first, the NND key is pressed to view the
other piece of CLIP information.
4-33
NEXT CALL
In the event that there is a call waiting or a camped-on call at the user’s keyset, the user can press the
NEXT key to display the Caller ID information associated with the next call in queue at the station.
Either the CLIP name or CLIP number will show in the display depending on the N/N selection.
SAVE CLIP NUMBER
At any time during an incoming call that provides CLIP information, the user may press the SAVE
key. This saves the CLIP number in the Save Number feature. Pressing the SAVE number redial key
will dial the CLIP number. The system must be using LCR to dial the saved number.
STORE CLIP/ANI NUMBER
At any time during an incoming call that provides CLIP information, the user may press the STORE
key. This saves the CLIP number as a speed dial number in the personal speed dial list. The system
must be using LCR to dial the stored number.
INQUIRE PARK/HOLD
When a user is informed that an incoming call is on hold or has been parked, the user may view the
Caller ID or ANI information before he/she retrieves the call. This will influence how the user
chooses to handle the call.
CLIP REVIEW LIST
This feature allows display keyset users to review CLIP information for calls sent to their stations.
This list can be from ten to fifty calls in a first in, first out basis. The list includes calls that were
answered and calls that rang the user’s station but that were not answered. When reviewing this list,
the user can press one button to dial the person back. The system must be using LCR to dial the
stored number.
INVESTIGATE
This feature allows selected stations with a special class of service to investigate any call in progress.
If CLIP information is available for an incoming call, the selected stations can know to whom the iDCS
100 user is speaking. On outgoing calls, the selected stations can see who was called. After
investigating, the selected stations may barge-in on the conversation, disconnect the call or hang up.
ABANDON CALL LIST (50)
The system has a system-wide abandon call list that stores CLIP information for calls that rang but
were not answered. The list is accessed using the operator’s passcode. When reviewing this list, you
are provided options to CLEAR the entry or DIAL the number. You can use the NND key to toggle
between the CLIP name, CLIP number and the date and time the call came in. The system must be
using LCR to dial numbers from the abandon call list. The abandoned call list will store up to 50.
CALLING PARTY NAME
For intercom calls, LCD 24B and LCD 12B keysets show the calling party’s name before answering.
The names must be stored in the system directory list and can be up to 11 characters long.
CALLING PARTY NUMBER
When an intercom call is received, all display stations show the calling party’s extension number
before the call is answered.
4-34
Chapter 4
Business Feature Package
CONFERENCE INFORMATION
When a conference is set up, each extension and outside line number is displayed at the controlling
station when it is added. When a station is added, its display shows [Conf with xxx] alerting the user
that other parties are on the line.
DATE AND TIME DISPLAY
In the idle condition, the current date and time are conveniently displayed. Display keysets can have
a 12 or 24 hour clock in either the ORIENTAL or WESTERN display format with information shown in
upper case or lower case letters.
DIAL BY NAME
Each station and speed dial number can have an associated directory name. Any station or speed dial
number can be selected by scrolling alphabetically through a directory list. There are three directories:
1. System wide speed dial list
2. Personal speed dial list
3. Station directory list
This online “phone book” allows display keyset users to look up and dial any speed dial number or
station in seconds.
DIALED NUMBER
When an outside call is made, digits are displayed as the user dials them. If the display indicates an
incorrect number was dialed, the user can quickly hang up before billing begins.
ENHANCED STATION PROGRAMMING
Personal programming options are easier to select and confirm with the help of the display.
IDENTIFICATION OF RECALLS
Hold recalls and transfer recalls are identified differently than other ringing calls. Hold recalls
indicate the recalling line or station number and the associated name. Transfer recalls indicate the
recalling line or station and where it is coming from.
IDENTIFICATION OF TRANSFERS
The display will identify who transferred a call to the user.
MESSAGE WAITING CALLER NUMBER
When the message indication is on, pressing the MESSAGE button displays the station number(s) of
the person(s) who have messages for the user. Display keyset users can scroll up and down to view
message indications.
OUTSIDE LINE IDENTIFICATION
Each line can be identified with an 11 character name. Incoming calls display this name before the call
is answered. This feature is helpful when individual lines must be answered with different greetings.
4-35
OVERRIDE IDENTIFICATION
If another station barges-in on a user’s conversation, the display will alert the user with a [Barge from
2xx] display if the system is set for barge-in with tone.
PROGRAMMED MESSAGE DISPLAY
Preprogrammed station messages set by other stations are displayed at the calling station’s keyset.
SOFT KEYS
Below the display, there are three soft keys and a SCROLL button. These keys allow the user to access
features in his/her class of service without requiring the keyset to have designated feature keys.
STOPWATCH TIMER
Display keyset users find this feature very convenient to time meetings, calls and other functions.
Users simply press once to start the timer and press again to stop the timer.
UCD SUPERVISOR DISPLAYS
With the optional AA card, when UCD is used, multiple supervisors can view information about the
UCD groups calls or agents.
Call Screen
This allows the supervisor to view how many calls are in queue, the longest wait time, how many calls
have been received today, what the average time in queue is and how many calls were abandoned.
Agent Screen
This allows the supervisor to monitor how many agents are logged in, check each agents status (IN
GROUP, OUT OF GROUP, or DND), view each agents total number of calls, average call length or
average ring time.
Accessing this screen will also allow a Supervisor to change the status of each agent (IN
GROUP, OUT OF GROUP, or DND).
4-36
Chapter 4
Business Feature Package
SAMPLE DISPLAYS
PROSTAR LCD 12B and LCD 24B display model keysets have a large, easy-to-read, 32 character liquid
crystal display. Helpful call processing information is provided so everyday call handling is quick and
easy. Here are just some of the displays you may see.
209: Tim Kelly
RRI 23 Sep 02:54
Camp on to 203
Wait for answer
Idle display shows extension, name, day,
This station is camped-on to extension 203
date and time.
and is waiting for 203 to answer.
Call for 501
202 Mr. Smith
Call for 501
706 Local #6
This station in the sales department is
This display tells you this is a new incoming
receiving a group call from Mr. Smith.
call to the sales department.
203: Busy
CBK MSG CAMP "
OHVA from 203
REJECT
This station is calling station 203 which is
This station is receiving an off-hook voice
currently busy.
announcement from station 203.
Conf with 203
John
CONF: 202 702
CONF "
This station is on a conference call with John,
This station is on a conference call with
extension 203. Assume other parties will hear
extension 202 and trunk 702 and has the
your conversation.
option to add two more parties.
Transfer to 203
John
Call from 201
Operator
This station is transferring a call to John at
This station is receiving a call from
extension 203.
extension 201.
DO NOT DISTURB
ON
OFF
703 Local 3
CONF PAGE MUTE "
This station is setting the Do Not Disturb
This station is receiving a call from
feature.
extension 201.
4-37
SAMPLE CALLER ID DISPLAYS
13054264100
702: RINGING
05/25, 09: 41, 702
CLEAR
NND
This display shows an incoming call from
This display shows the information on the
1-305-426-4100 on Line 702 ringing
abandoned call list. This call came in on May 25
directly at your station.
at 9:41 A.M on line 702. The user can CLEAR
the entry. DIAL the caller back or examine
further NND information.
13054264100
TRANSFER FM 201
SAMSUNG TELECOM
CLEAR
NND
This display shows an incoming call from
This display shows an entry in a station review list
1-305-426-4100 on Line 702 ringing
showing the three initial options. The arrow
directly at your station.
indicates other options available to you by
pressing the SCROLL key.
SAMSUNG TELECOM
BARGE NND DROP
13054264100
NEXT NND
ANS
This display shows an investigation of a
This display is seen while examining calls
station that is talking to Samsung
in oueue at your keyset.
Telecom. Investigator can BARGE-in to
the conversation, DROP the call from the
system of examine further NND
information.
SAMSUNG TELECOM
CALL FOR: 500
TALKING TO: 203
BARGE
DROP
This display shows an incoming call from
This display can be seen when
Samsung Telecom ringing at group 500.
investigating an intercom call.
The investigator can BARGE-in or
DROP the connection.
SAMSUNG TELECOM
ANS NND IGNORE
This display is seen while using the
INQUIRE feature. It shows the three
options available while you are checking
on a held or parked call.
4-38
Chapter 4
Business Feature Package
SAMPLE UCD DISPLAYS
005 calls in
queue now
06 available
04 logged in
There are five calls currently waiting to be
There are six members in the group. Four of the
answered by the UCD group.
members are currently logged in.
longest wait
time is 02:24
201: answered
065 calls today
The longest call on hold (waiting to be
The agent at station 201 has answered 65
answered) was for two minutes, 24
calls today.
seconds. This data applies to all calls since
the supervisor data was last cleared. It
does not necessarily represent calls
currently in queue.
124 calls
received today
201: average
call time 04:43
The UCD group has received 124 calls
The average call length for station 201 is
today.
four minutes and 43 seconds.
average time in
queue is 03:51
202: Sondra
STATUS: OUT
The average time on hold (waiting to be
Station 202 is currently out of the group.
answered) is three minutes and 51
(The display can also show IN GROUP
seconds.
and DND.)
4-39
SAMPLE SMDR PRINTOUT (WITHOUT CALLER ID)
1
T
202
226
208
EXT
702
704
703
703
705
TRK
09/23
09/23
09/23
09/23
09/23
09/23
09/23
MM/DD
16:21:31
16:21:12
16:18:16
16:19:53
16:15:51
16:15:28
16:14:00
16:13:31
16:12:33
STT.TIME
00:04:15
00:00:19
00:01:57
00:00:25
00:01:45
00:01:52
00:00:25
00:00:29
00:05:12
DURATION
IT
O
T
I
O
TT
IT
OT
FG
12145551234567
DIALED DIGIT
SMDR REPORT FOR [Samsung R & D] 09/23/94 17:30
1
210
703
09/23
AUTH
1
201
703
09/23
1
1
1
1
1
1
208
211
210
208
204
211
09/23
09/23
09/23
09/23
17:16:55
17:12:05
17:12:07
17:04:10
16:20:59
00:02:43
GROUP IN
GROUP OUT
DND OFF
709
735
735
09/23
09/23
09/23
09/23
09/23
18:00:03
17:25:15
17:25:15
17:18:08
17:17:38
17:17:15
00:08:12
00:10:25
00:00:28
00:12:19
00:00:30
00:00:11
O
FO
FI
DO
DI
DE
13054264100
4205071
DND ON
18005551234
ALARM RINGING
4205068
4205069
1
208
09/23
5555
702
1
207
209
701
09/23
O
1
207
735
706
706
1
1
1
706
705
Telephone No. Dialed
1-18 Digits
13055551234
3833
1
701
1
1
312
2326
1
Call Type Flag
2 Characters
Call Duration
Hrs:Mins:Secs
Time Call Made or Received
Hrs:Mins:Secs
1
C.O. Line No.
2-4Digit
Authorization Code Data Call Made or
Received Month:Day
4 Digit
Extension
2-4Digit
Tenant
1 Digit
ACCOUNT CODE
1234567890*#
987654321012
232552779600
Account Code
1-12 Digits
O
I
DI
DO
FO
DE
T
IT
FI
OT
DISA call with error
Transferred call that was
terminated
Incoming transfer
Incoming call forwarded to
an external number
Outgoing transfer-Outgoing call
made and transferred
Caller received a transferred
call and transferred it again
Call Type Flag Definitions
Outgoing
Incoming Call
DISA call in
DISA call out
Outgoing record
of forwarded call
TT
Chapter 4
4-40
Business Feature Package
SAMPLE SMDR PRINTOUT (WITH CALLER ID)
SMDR REPORT FOR [Samsung R & D] 09/23/94 17:30
1
1
1
1
1
1
1
1
1
1
T
203
203
201
203
203
203
217
202
202
247
205
201
EXT AUTH
702
702
701
701
702
702
702
702
702
702
702
701
701
TRK
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
01/02
MM/DD
17:41:45
17:33:24
17:31:06
17:29:54
17:28:38
17:28:34
17:28:04
17:27:13
17:26:46
17:26:35
17:25:56
17:25:14
17:24:49
17:15:41
17:15:13
STT.TIME
00:00:30
00:02:18
00:03:00
00:00:00
00:00:14
00:00:04
00:00:00
00:00:20
00:00:16
00:00:11
00:00:00
00:00:03
00:00:25
00:00:02
00:00:28
DURATION
A
T
TT
OT
T
IT
O
O
T
IT
O
T
IT
T
IT
4264385
4264385
FG DIALED DIGIT
13055553426
13055556420
13055556420
13055558703
13055559748
13054264385
13054264385
13055552354
13055557890
13054264100
13054264100
TERRY PRUITT
PIZZA DELIVERY
PIZZA DELIVERY
LENNY WILKINS
JOAN LEVIN
SAMSUNG TELECOM
SAMSUNG TELECOM
SUSAN HOLLINS
CURTIS SMITH
SAMSUNG TELECOM
SAMSUNG TELECOM
CID/ANI NAME
1
205
702
CID/ANI NUMBER
1
701
ACCOUNT CODE
1
209
5556420
4264100
1
01/03
01/02
17:51:17
17:42:15
00:00:22
00:00:02
A
O
A
13055556733
13055554676
CHAZ NEWMAN
ALEX DAULTON
BLANCHE MARKER
1
701
00:00:05
13055559723
5555069
702
17:56:02
A
203
01/03
00:00:54
1
701
17:56:07
1
1
01/03
Caller ID/ANI Name
1-15 Characters
701
Telephone No. Dialed
1-18 Digits
Caller ID/ANI Number
1-15 Digits
1
Account Code
1-12 Digits
Time Call Made or Received
Hrs:Mins:Secs
Call Duration
Hrs:Mins:Secs
Call Type Flag
2 Characters
C.O. Line No.
2-4Digit
Authorization Data Call Made
Code 4 Digit
or Received
Month:Day
Extension
2-4Digit
Tenant
1 Digit
O
I
DI
DO
FO
DISA call with error
Transferred call that was
terminated
Incoming transfer
Incoming call forwarded to
an external number
Outgoing transfer-Outgoing call
made and transferred
Caller received a transferred
call and transferred it again
Call Type Flag Definitions
Outgoing
DE
Incoming Call
T
DISA call in
DISA call out
IT
Outgoing record FI
of forwarded call
OT
TT
4-41
SAMPLE UCD REPORT
UCD GROUP 529 : SALES
FROM: SUN 02 Feb 00:00
TO : SUN 02 Feb 02:54
CALL STATISTICS
===============
AVERAGE RING TIME(TIME TO ANSWER)......
NUMBER OF TIMES ALL AGENTS BUSY........
AVERAGE TIME IN QUEUE..................
TOTAL CALLS RECEIVED...................
LONGEST QUEUE TIME(TODAY)..............
TOTAL CALLS ABANDONED..................
AGENT STATISTICS
================
MEMBER
AGENT
00:40
00002
00:51
00011
02:14
00004
NAME
CALLS
AVERAGE
RING
ANSWERED
CALL TIME
TIME
--------------------------------------------------------------------01
210
JOHN
0002
01:55
00:05
02
211
SAM
0001
02:18
00:06
03
208
MIKE
0003
01:22
00:04
04
207
PETER
0001
03:16
00:05
======================================================================
UCD GROUP 515 : SUPPORT
FROM: MON 03 Jan 08:30
TO : SUN 02 Jan 02:54
CALL STATISTICS
===============
AVERAGE RING TIME(TIME TO ANSWER)......
NUMBER OF TIMES ALL AGENTS BUSY........
AVERAGE TIME IN QUEUE..................
TOTAL CALLS RECEIVED...................
LONGEST QUEUE TIME(TODAY)..............
TOTAL CALLS ABANDONED..................
AGENT STATISTICS
================
MEMBER
AGENT
NAME
00:07
00005
01:06
00023
01:02
00001
CALLS
AVERAGE
RING
ANSWERED
CALL TIME
TIME
-----------------------------------------------------------------01
223
FRED
0012
02:33
00:08
02
213
JANE
0010
01:04
00:04
4-42
Chapter 4
Business Feature Package
UCD CALL STATISTICS
CALLS IN QUEUE NOW
How many calls are currently in queue.
This statistic is a real time statistic and so will not print on a report.
ABANDONED CALLS
This shows the number of callers that reached the UCD group, but hung up before being answered. A
high number probably means that there are not enough agents available and the wait time is too long.
AVERAGE RING TIME
This is calculated from the time an agent begins to ring until the time an agent answers the call, this
does not include ringing at an agent station that does not answer or is logged out because of the ring
next option.
NUMBER OF TIMES ALL AGENTS BUSY
This is the number of times that a call is placed to an UCD group and all agents are busy or out of
group. This check is made when the call is first placed to the group.
Example: If there are 5 members in a group, 3 are Out of Group one is busy and one is idle, and a call
is placed to the group, because there is an idle station the all agents busy counter is not incremented.
If the idle station rings, does not answer and is logged out, although the condition of the group is now
all agents busy, the check has been made and the agent busy statistic does not increment.
Also if a call comes into a group with all agents busy and then one becomes idle, the busy counter will
increment because the check has been made.
AVERAGE TIME IN QUEUE
This is calculated as an average of all the calls that were in queue.
Note that this is ONLY an average of the calls that were in queue. The caller must have overflowed to
the UCD recording to be considered in queue.
A call is considered in queue until it is answered or until it goes to the final destination.
TOTAL CALLS RECEIVED
The total number of times that calls were sent to a group. This includes calls that were answered by
the group, calls that went to a group with all agents busy or out of group, calls that are abandoned and
calls that go to UCD final destination. This includes intercom calls to the UCD group.
If this number is less than the total calls received by all the agents it is possible that calls were
transferred from one agent to another.
If this number is more than the total calls received by all the agents it is possible that calls were
unanswered by an agent and went to final destination or callers hung up while in queue.
4-43
This statistic includes:
a) Calls answered by agent.
b) Calls that are not answered by an agent and go to final destination.
c) Calls that are sent to the UCD group but callers hang up before being answered.
LONGEST QUEUE TIME TODAY
This shows the longest call in queue today. The queue time is calculated as follows:
a) Queue time begins when a caller starts to hear the first UCD message.
b) Queue time ends when a caller is either
• Answered by an agent
• System gets disconnected from C.O. or
• Caller is transferred to final destination
LONGEST QUEUE TIME NOW
This shows the longest call currently in queue. The queue time is calculated as follows:
a) Queue time begins when a caller starts to hear the first UCD message.
b) Queue time ends when a caller is either
• Answered by an agent
• System gets disconnected from C.O. or
• Caller is transferred to final destination
4-44
Chapter 4
Business Feature Package
UCD AGENT STATISTICS
LOGGED IN
The number of stations programmed in the UCD group and the number of stations that are currently
logged in.
This statistic is a real time statistic and so will not print on a report.
STATUS
This screen shows the agents name, extension number and status. The status can be In Group, Out of
group or in DND.
This statistic is a real time statistic and so will not print on a report.
CALLS ANSWERED
The total number of calls answered by the agent. This does not include ring no answer to an agent
station.
If this total number is less than the calls received by the group it is possible that calls were
unanswered by an agent and went to final destination or that callers hung up while in queue.
If this total number is more than the calls received by the group it is possible that calls were
transferred from one agent to another.
AVERAGE CALL TIME
This is an average of all the call durations for the agent.
AVERAGE RING TIME
This is an average of all the ring times for the agent. Ring times are previously explained.
4-45
SAMPLE TRAFFIC REPORT
TRAFFIC REPORT FOR [ SAMSUNG ] Mar/21/1999 13:35
**************************** SYSTEM STATISTICS *******************************
BEGINNING:
Mar/15/1999
00:42
ENDING: Mar/21/1999 13:32
ACTIVITY
SYSTEM TOTAL
INCOMING TRUNK CALLS
INCOMING TRUNK CALLS
OUTGOING TRUNK CALLS
A SELECTED TRUNK WAS
- ANSWERED..................
- NOT ANSWERED..............
............................
BUSY........................
3041
26
2168
44
INTERCOM CALLS – COMPLETED .......................
INTERCOM CALLS - NOT ANSWERED ....................
7178
1540
TRUNK RECALLS TO STATION .........................
TRUNK RECALLS TO OPERATOR GROUP ..................
145
32
INTERNAL PAGE USED ...............................
35
EXTERNAL PAGE USED ...............................
79
ALL PAGE USED ....................................
231
***************************** TRUNK GROUPS ***********************************
GROUP
OUTGOING BUSY
9
1245
18
800
521
3
801
20
3
802
0
0
*************************** INDIVIDUAL TRUNKS ********************************
TRUNK
701
702
703
TRUNK-NAME
LOCAL 1
LOCAL 2
LOCAL 3
ATTA
0
0
0
ANSD
737
541
290
NOT-ANSD
0
4
1
OUTGOING
19
26
37
BUSY
12
11
21
************************* STATION HUNT GROUPS ********************************
GROUP
500
501
502
503
504
<———————— OUTSIDE CALL ————————>
ANSD
NOT-ANSD
439
19
261
37
40
2
87
5
19
1
<-INTERCOM->
ANSD
61
38
77
162
44
*********************** INDIVIDUAL STATIONS **********************************
EXT
201
202
203
<—————— OUTSIDE CALL ——————————————————————————><-INTERCOM——>
STATION-NAME ATTA ANSD NOT-ANSD DIALED ICM–TRSF TRK-TRK PICKUP ANSD DIALED
Operator
9
360
11
15
341
0
0
39
72
Barbara
12 60
2
80
20
0
12
49
66
Ivania
4
25
1
36
3
0
18
86
29
4-46
Chapter 4
Business Feature Package
TRAFFIC REPORT OVERVIEW
A**************************** SYSTEM STATISTICS **************************
1 BEGINNING: Mar/15/2001 08:00
ENDING: Mar/15/2001 17:30
2 ACTIVITY SYSTEM TOTAL
3
4
5
6
INCOMING TRUNK CALLS
INCOMING TRUNK CALLS
OUTGOING TRUNK CALLS
A SELECTED TRUNK WAS
- ANSWERED..................0000
- NOT ANSWERED..............0000
............................0000
BUSY........................0000
7 INTERCOM CALLS - COMPLETED.......................0000
8 INTERCOM CALLS - NOT ANSWERED....................0000
9 TRUNK RECALLS TO STATION.........................0000
10 TRUNK RECALLS TO OPERATOR GROUP.................0000
11 INTERNAL PAGE USED..............................0000
12 EXTERNAL PAGE USED..............................0000
13 ALL PAGE USED...................................0000
1. BEGINNING & ENDING
This identifies when the statistics were collected. It includes dates and time.
2. ACTIVITY
Overall summary of traffic in the system for activities 3 to 13.
3. INCOMING TRUNK CALLS-ANSWERED
These are any incoming trunk calls to the system. These calls are pegged when answered by any
device and/or station in the system whether it is a new call or a recall.
4. INCOMING TRUNK CALLS-NOT ANSWERED
These are any incoming trunk calls that were not answered by any station or device in the systems.
These are the same calls that would be flagged as abandoned in SMDR.
5. OUTGOING TRUNK CALLS
These are all outgoing trunk calls that were originated by any station or through the DISA feature.
Outgoing trunk calls are valid calls as defined by the SMDR START TIME in MMC 501.
6. A SELECTED TRUNK WAS BUSY
Pegged every time a trunk or trunk group was busy regardless of the manner in which it was
selected (e.g., DTS key, LCR, “9”, 7XX, TRK GROUP SELECT, SPD, External call forward, DISA).
7. INTERCOM CALLS COMPLETED
These are all intercom calls that were completed to any station, station group or device.
8. INTERCOM CALLS NOT COMPLETED
These are all intercom calls that were not answered and resulted in the calling party hanging up. A
call to a station group that overflows to another station is considered not answered whether the
overflow destination did or did not answer.
4-47
9. TRUNK RECALLS TO STATION
These are trunk calls that were placed on any kind of hold and recalled a station. These are also
trunk calls that were transferred and were not answered and recalled the transferring station. This
includes members of the operator group that put calls on hold and then recall the operators station.
10.TRUNK RECALLS TO OPERATOR GROUP
These are any trunk calls that recalled to the operator group.
11.INTERNAL PAGE USED
Peg count of every time internal page was accessed.
12.EXTERNAL PAGE USED
Peg count for every time external page was accessed.
13.ALL PAGE USED
Peg count of every time the all page feature was accessed. This does not include internal or
external page, only 55+ * or PAGE *.
B**************************** TRUNK GROUPS **************************
1 GROUP
9
800
801
2 OUTGOING
0000
0000
0000
3 BUSY
0000
0000
0000
1. GROUP
A listing of all trunk groups assigned in the system.
2. OUTGOING
These are the number of outgoing trunk calls made using each trunk group. Pegged every time a
member of this trunk group was used to make a valid outgoing call. A valid outgoing call is
defined by the SMDR Start Time programmed in MMC 501.
3. BUSY
This is the number of times each trunk group was busy when someone attempts to access it.
4-48
Chapter 4
Business Feature Package
C**************************** INDIVIDUAL TRUNKS **************************
1TRUNK
701
702
703
704
705
706
707
708
709
710
2TRUNK-NAME
3ATTA
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
4ANSD
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
5NOT-ANSD
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
6OUTGOING
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
7BUSY
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
1. TRUNK
A listing of each trunk in the system.
2. TRUNK NAME
The names of each trunk as programmed in MMC 404.
3. ATTA
Average Time To Answer for trunks is counted in the number of seconds that ringing voltage is
detected at the trunk interface and the timer stops when trunk is answered by station or device in
the system. The ATTA is the sum of all answered times divided by the answered call count.
4. ANSD
This is the number of times this specific trunk was answered by any station or device whether it is
a new call or a recall.
5. NOT-ANSD
This is the number of times this specific trunk rang the system but was not answered. These are
the same calls that would be flagged as abandoned in SMDR.
6. OUTGOING
This is the number of times this trunk was used to make an outgoing call. A valid outgoing call is
defined by the SMDR START TIME programmed in MMC 501.
7. BUSY
This is the number of times this trunk was busy when accessed by a button or dial code.
4-49
D************************** STATION HUNT GROUPS **************************
<———————— 1 OUTSIDE CALL —————————————————————> 5 <INTERCOM->
2GROUP
500
501
502
503
3ANSD
0000
0000
0000
0000
4NOT-ANSD
0000
0000
0000
0000
6ANSD
0000
0000
0000
0000
1. OUTSIDE CALLS
These statistics are for outside calls that reach these station groups regardless how they arrive
there.
2. GROUP
Listing of all station groups in the system.
3. ANSD
This column is a peg count of all answered trunk calls that rang to the specific group directory
number regardless of how these arrived.
4. NOT-ANSD
The number of times any trunk call directed to the specific group number was not answered by any
member of the group.
5. INTERCOM
An intercom call made from a station or device within the system to the specific group number.
6. ANSD
This is a count of how many times an intercom call was answered by any group member of that
specific group.
4-50
Chapter 4
Business Feature Package
E****************************** INDIVIDUAL STATIONS **************************
1
11
<—————————————————— OUTSIDE CALL —————————————————> <-INTERCOM->
2
3
4
5
6
7
8
9
10
12
13
EXT STATION-NAME ATTA ANSD NOT-ANSD DIALED ICM-TRSF TRK–TRK PICKUP ANSD DIALED
201
0000 0000
0000
0000
0000
0000
0000 0000 0000
202
0000 0000
0000
0000
0000
0000
0000 0000 0000
203
0000 0000
0000
0000
0000
0000
0000 0000 0000
1. OUTSIDE CALLS
These statistics are for outside calls that in any way reach individual stations or devices.
2. EXT
Listing of all extension numbers in the system. This also includes AA, VM, and CADENCE ports.
3. STATION NAME
The name for each particular station as programmed in MMC 104.
4. ATTA
Average Time To Answer for stations is counted in the number of seconds that ringing signal is
applied to a station for trunk calls and recalls. The ATTA is the sum of all answered times divided
by the answered call count. Use the same calculation method as used for individual trunk ATTA.
5. ANSD
This is a count of how many times an outside call was answered by the specific station. Outside
callers recalling a station are not counted again when they are answered.
6. NOT-ANSD
This is a count of how many times a trunk call was directed to the station but was not answered by
this station.
7. DIALED
Peg count of how many times the station made a valid outside call. An outside call is defined by
the SMDR start time in MMC 501.
8. ICM-TRSF
This is the number of times a trunk call was successfully transfered to another station using the
intercom. It includes both screened and unscreened transfer.
9. TRK–TRK
This is the number of times a trunk call was transfered to another trunk (tie line) This is called a
trunk–to–trunk transfer. This field gets pegged every time the station completes a trunk to trunk
transfer.
10.PICKUP
This is a count of the outside calls that were picked up by the specific station. Picked-up calls are
calls that are not ringing at your station but were answered by you. This peg count is separate
from the number of answered call in #5 of Individual Stations section E.
4-51
11.INTERCOM
Statistics for intercom calls. An intercom call made from a station or a station device within the
system to another station.
12.ANSD
This is the number of times an intercom call was answered by this specific station. Screened
transfers count as an answered intercom call.
13.DIALED
The number of times the specific station dialed another station or station group. Screened transfers
count as a dialed intercom call.
4-52
Chapter 4
Business Feature Package
SAMPLE ALARM REPORT
ALARM REPORT FOR [iD C S 100 SAMPLE ] MAR/24/1999 19:45
==============================================================================
MM/DD/YYYY ERR.TIME ERR.CODE ERROR DISPLAY
POSITION
==============================================================================
03/14/1999 16:45:00 [MNF03] IPC Error
C1-S01
03/14/1999 16:45:00 [MNF03] IPC Error
C1-S04
03/14/1999 16:45:00 [MNF03] IPC Error
C1-S01
03/14/1999 16:45:00 [MNF03] IPC Error
C1-S04
03/14/1999 16:45:00 [MNF03] IPC Error
C1-S01
03/14/1999 16:45:00 [MNF03] IPC Error
C1-S04
03/14/1999 16:46:00 [MNF01] Card Out
C1-S05
03/14/1999 16:46:00 [MNF02] Card In
C1-S05
03/14/1999 16:47:00 [MJD01] SYNC Failure
C1-S05
03/14/1999 16:47:00 [MJD02] SYNC Recvry
C1-S05
03/16/1999 16:47:00 [MNF04] Trunk Fault
C1-S06-P03
03/16/1999 16:48:00 [MNF05] Trunk Recvry
C1-S06-P01
03/16/1999 16:48:00 [MNF05] Trunk Recvry
C1-S06-P02
03/16/1999 16:48:00 [MNF05] Trunk Recvry
C1-S06-P03
03/18/1999 16:51:00 [MNF01] Card Out
C1-S02
03/18/1999 16:51:00 [MNF02] Card In
C1-S02
03/19/1999 17:23:00 [MNF01] Card Out
C1-S03
03/20/1999 17:24:00 [MJC01] DTMF Fault
BASE
03/20/1999 17:24:00 [MNF03] IPC Error
C1-S01
03/20/1999 17:24:00 [MNF03] IPC Error
C1-S04
03/24/1999 17:24:00 [MJD19] PRI Restart
C1-S07
4-53
DECT Service
iDCS 100 system provides DECT cordless communications in a single office or throughout a large
commercial or industrial complex. To implement this service, you need 8BSI card, DBS card and
DECT handsets. Users of this service meet improved overall efficiency, since staff can be reached or
make calls wherever they are.
4-54
Chapter 4
Business Feature Package
(This page is left blank intentionally.)