Samsung WC-M15i Series Service manual

FACSIMILE
WC-M15i Series
SERVICE
MANUAL
Contents
FACSIMILE
1. Precautions
2. Specifications
3. Circuit Description
4. Disassembly
5. Troubleshooting
6. Exploded Views and Parts List
7. Electrical Parts List
8. Block Diagram
9. Connection Diagram
10. Schematic Diagrams
- This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law. -
Precautions
1. Precautions
Follow these safety, ESD, and servicing precautions to prevent personal injury and equipment damage.
1-1 Safety Precautions
1. Be sure that all built-in protective devices are in
place. Restore any missing protective shields.
2. Make sure there are no cabinet openings
through which people- particularly childrenmight insert fingers or objects and contact dangerous voltages.
3. When re-installing chassis and assemblies, be
sure to restore all protective devices, including
control knobs and compartment covers.
4. Design Alteration Warning:Never alter or add to
the mechanical or electrical design of this equipment, such as auxiliary connectors, etc. Such
alterations and modifications will void the manufacturer’s warranty.
7. Product Safety Notice:Some electrical and
mechanical parts have special safety-related
characteristics which might not be obvious from
visual inspection. These safety features and the
protection they provide could be lost if a replacement component differs from the original. This
holds true, even though the replacement may be
rated for higher voltage, wattage, etc.
8. Components critical for safety are indicated in
the parts list with symbols .
Use only replacement components that have the
same ratings, especially for flame resistance and
dielectric specifications. A replacement part that
does not have the same safety characteristics as
the original may create shock, fire, or other
safety hazards.
5. Components, parts, and wiring that appear to
have overheated or are otherwise damaged
should be replaced with parts which meet the
original specifications. Always determine the
cause of damage or overheating, and correct any
potential hazards.
6. Observe the original lead dress, especially near
sharp edges, AC, and high voltage power supplies. Always inspect for pinched, out-of-place,
or frayed wiring. Do not change the spacing
between components and the printed circuit
board.
1-1
Precautions
1-2 ESD Precautions
1. Certain semiconductor devices can be easily
damaged by static electricity. Such components
are commonly called “Electrostatically Sensitive
(ES) Devices”, or ESDs. Examples of typical
ESDs are: integrated circuits, some field effect
transistors, and semiconductor “chip” components.
4. Use only a grounded tip soldering iron to solder
or desolder ESDs.
Use only an “anti-static” solder removal device.
Some solder removal devices not classified as
“anti-static” can generate electrical charges sufficient to damage ESDs.
5.
The techniques outlined below should be followed to help reduce the incidence of component
damage caused by static electricity.
CAUTION : Be sure no power is applied to the chassis
or circuit, and observe all other safety precautions.
2. Immediately before handling a semiconductor
component or semiconductor-equipped assembly, drain off any electrostatic charge on your
body by touching a known earth ground. Alternatively, employ a commercially available wrist
strap device, which should be removed for your
personal safety reasons prior to applying power
to the unit under test.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most replacement ESDs are packaged
with all leads shorted together by conductive
foam, aluminum foil, or a comparable conductive
material.
7. Immediately before removing the protective
shorting material from the leads of a replacement ESD, touch the protective material to the
chassis or circuit assembly into which the device
will be installed.
8.
3. After removing an electrical assembly equipped
with ESDs, place the assembly on a conductive
surface, such as aluminum or copper foil, or conductive foam, to prevent electrostatic charge
buildup in the vicinity of the assembly.
Do not use Freon-propelled chemicals. When
sprayed, these can generate electrical charges
sufficient to damage ESDs.
Maintain continuous electrical contact between
the ESD and the assembly into which it will be
installed, until completely plugged or soldered
into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such
as the brushing together of clothing fabric and
lifting one’s foot from a carpeted floor, can generate static electricity sufficient to damage an ESD.
1-3 Super Capacitor or Lithium Battery Precautions
1. Exercise caution when replacing a super capacitor or Lithium battery. There could be a danger of
explosion and subsequent operator injury and/or
equipment damage if incorrectly installed.
3. Super capacitor or Lithium batteries contain toxic
substances and should not be opened, crushed,
or burned for disposal.
2. Be sure to replace the battery with the same or
equivalent type recommended by the manufacturer.
4. Dispose of used batteries according to the manufacture’s instructions.
1-2
Specification
2. Specification
Specifications are correct at the time of printing. Product specifications are subject to change without notice.
See below for product specifications.
2-1 General Specifications
Item
Description
Type of Unit
Desktop
Operation System
Win95/98/ME/ NT /2000/XP
Duplex Printing
Yes(Default)
Interface
IEEE1284(ECP)
USB(without HUB mode)
CPU
120 MHz(ARM946ES)
Emulation
PCL6
Warming up Time
30 Sec (Stand-By), 25˚C
Absolute Storage Condition
Temperature : -20°C ~ 40°C,
Humidity : 10% RH ~ 95% RH
Operating Condition
Temperature : 10˚C ~ 32˚C,
Humidity : 20% RH ~ 80 % RH
Recommended Operating Condition
Temperature : 16°C ~ 30°C,
Humidity : 30% RH ~ 70% RH
Dimension(W X D X H)
560 X 433 X 459 mm
Weight
About 22.5 Kg(with CRU)
* Acoustic Noise
Less than 56/50 dB(Copy/Printing mode)
Power Rating
AC 100VAC ~ 127VAC ± 15 %, 50/60Hz ± 3Hz
AC 220VAC ~ 240VAC ± 15 % , 50/60Hz ± 3Hz
Power Consumption
Avg. 320Wh
Power Save Consumption
Avg. 35Wh
Recommended System Requirement
Pentium IV 1.2 Ghz, 128 MB RAM, 220MB(Hard Disk)
Minimum System Requirement
Pentium II 400Mhz, 64 MB RAM, 120MB(Hard Disk)
LCD
16 characters X 2 lines
Memory
4 Mbyte for flash Memory , 16 Mbyte for SDRAM
* Sound Pressure Level, ISO 7779
Samsung Electronics
2-1
Specification
2-2 Printer Specifications
Item
Description
Printing Method
Laser Scanning Unit + Electro Photography
*Speed
Single Side : Up to 15 PPM
(Letter Size, 5% Character Pattern)
Duplex : Up to 7.5 IPM(Images/Min) (Letter Size, 5% Character Pattern)
Source of Light
LSU(Laser Scanning Unit)
Duplex Printing
Yes(Default)
Resolution(Horizontal X Vertical)
Up to 1200 x 1200 DPI effective output
Feed Method
Cassette Type , By Pass Tray,
ADF(Automatic Document Feeder)
Feed Direction
FISO(Front-In Side-Out)
Paper Capacity(Input)
Cassette : 550 Sheets
By Pass Tray : 100 Sheets(based on 75g/ß≥, 20lb)
Paper Capacity(Output)
Face Down : 250 Sheets
Effective Print Width
203 ± 1mm (8 inch)
* Print speed will be affected by Operating System used, computing performance, application software,
connecting method, media type, media size and job complexity.
2-3 Facsimile Specification(SCX-5315F Only)
Item
Description
Standard Recommendation
ITU-T Group3(ITU : International Telecommunications Union)
Application Circuit
PSTN or behind PABX
(PSTN : Public Switched Telephone Network.
PABX : Private Automatic Branch Exchange)
Data coding(Compression)
MH/MR/MMR/JPEG(Transmission)
Modem speed
33600 /14400/12000/9600/7200/4800/2400 bps
Transmission Speed
Approximately 3 sec(33,600 bps)
Effective Scanning Width
8.2 inches(208 mm)
Halftone
256 Levels
Paper Capacity(Input)
ADF(Automatic Document Feeder) : 30Sheets(75g/ß≥)
FAX Mode
Standard /Fine/Super Fine/Halftone
Memory
4MB
2-2
Samsung Electronics
Specification
2-4 Scanner Specification
Item
Description
Type
Flatbed(with ADF)
*Speed
Mono : Up to 1.2 msec/line, Color : Up to 2.5 msec/line
Device
Color CCD(Charge Coupled Device) Module
Interface
IEEE1284(ECP Support)
USB(without HUB Mode)
Compatibility
TWAIN Standard , WIA
Optical Resolution(H X V)
Up to 600 x 600 DPI effective output
Interpolation Resolution
Max. 4800 dpi
Halftone
256 Levels
Effective Scan width
8.2 inches(208 mm)
* Speed will be affected by Operating System used, computing performance, application software, connecting
method, media type, media size and job complexity.
2-5 Copy Specification
Item
Description
Mode
B/W
Quality
Text/Photo/Mixed
Mono Copy Speed(1)
Platen(SDMP) : Up to 12 cpm in A4 size, IDC 5% pattern
ADF (SDMP) : Up to 12 cpm in A4 size, IDC 5% pattern
ADF (MDSP) : Text/mixed : Approx. 7 cpm in A4 size, IDC 5% pattern
: Photo
: Approx. 3 cpm in A4 size, IDC 5% pattern
Optical Resolution (H x V)
Up to 600 x 600 DPI effective output
Multi Copy
99 pages
Maximum Original Size
Legal
Maximum Page Size
Legal
Paper Type Selection
Plain , Legal , Cardstock , Transparency
Zoom Range
Platen : 25 ~ 400%(1% Step)
ADF : 25~100 %(1% Step)
NOTE :
(1) Speed claims based on the test chart : Letter size.
SDMP : Single Document Multiple Printout
MDSP : Multiple Document Single Printout
• Speed will be affected by Operating System used, computing performance, application software,
connecting method, media type, media size and job complexity.
Samsung Electronics
2-3
Specification
2-6 Telephone Specification(SCX-5315F Only)
Item
Description
Speed Dial
80EA
Tone/Pulse
Tone only user modeTone/Pulse selectable in tech mode.
2-7 Consumables
Item
Type
Life
2-4
Description
Separate type
(Toner Cartridge / Drum Cartridge)
Toner Cartridge
Up to 6,000 sheets
( 5% coverage pattern, simplex normal mode )
Drum Cartridge
Up to 15,000 sheets
(simplex normal mode )
Samsung Electronics
Circuit Description
3. Circuit Description
3-1 Main PBA
3-1-1 Summary
The main circuit that consists of CPU, MFP controller (built-in 32bit RISC processor core: ARM946ES) including various I/O device drivers, system memory, scanner, printer, motor driver, PC I/F, and FAX transceiver controls the whole system. The entire structure of the main circuit is as follows :
OPE
H
SUPPLY
V
V
BLADE
FEED MOTOR
11P
2P
3P
CN 2 3
CN 2 1
CN 2 6
CN 5
CN22
CN1
CN20 CN27 CN30
CN28 CN3 CN24
CN 2 9
22P
DEV MOTOR
8P
LSU
THERMISTOR
FAN1
3P
FAN1
3P
CN 1 3
4P
10P
CN 1 8
2P
USB CABLE
MOTOR
DRIVER
H
+5V/+24V/+12V/+24Vs/Fuser
C N1 0 CN 1 1
4P
24P
CN 7
DEV CNT
MAIN PBA
CN 1 9 CN 1 7
4P
CN 2 5
HYPER
CN 1 9
2P
16MB
CN15(100P)
CN 1 2
PCNT
CN 3 1
4P
OPC
ADF
CN 3 3 CN 4
SDRAM DIMM
OUT BIN FULL
Option
CN 1 4
SCF
8P
CN 1 6
36P
15P D-SUB
FLAT MOTOR
Flash DIMM
PS3 (2MB)
CN15(100P)
Network CARD
CENTRONICS
CABLE
CN6
MICOM
- LCD Drive
- Key Scan
D-SUB
CONN.
DEV
SMPS / HVPS
CN2
CN8
Platen
M
SCAN
LCD 20x2line
5P
T
DEV_ID
3P
TONER_TX
4P
TONER_RX
2P
PTL
4P
COVER OPEN
S/W
+24V / +5V
DADF MOTOR
10P
PAPER SENSOR
POS,DET
3P x 2EA
CCD MODULE
External
Auditron
3P
3P
TRANSFORMER
6P
600/ / 600
2P
2P
14P
2P
Tx: Rx
LINE
SOLENOID
PICK_UP,DUPLEX,MP
PAPER
SENSOR
INT ERFACE
MODEM
EXT_PHONE
SEPRATING
PART
EXTERNAL
PHONE
INTERFACE
PART
LIU
LINE1
EXTERNAL
PHONE
FEED+P.EMP,EXIT,MP
<Block Diagram>
3-1
Circuit Description
3-2 Circuit Operation
3-2-1 Clock
1) System Clock
Device
Oscillator
Frequency
12MHz
• ARM946ES RISC PROCESSOR: drives PLL internally uses 120MHz and external Bus uses 60 MHz.
2) Video Clock
Device
Oscillator
Frequency
57.0167MHz
• Fvd =((PAPER 1SCAN LINE sending time * SCAN effective late /1SCAN LINE DOT #)*4
=(600dpi*600dpi*58.208mm/s*216mm*4)/(25.4mm*25.4mm*76.1%)=28.697MHz
•PAPER 1SCAN LINE sending time=SCAN LINE interval/DOCUMENT SPEED (58.208mm/S)
•1SCAN LINE DOT #=MAZ SCAN distance(216mm)*DOT# per 1mm
3)USB Clock
Device
Oscillator
Frequency
48MHz
3-2-2 POWER ON/OFF RESET
1) Signal Operation
Input Signal
Output Signal
RESET TIME (Td)
+3.3V Power Line (VCC)
ARM946ES nRESET and 29LU16ø
• POWER ON/OFF DETECT VCC RISING/FALLING 4.5°≠4.6V
1.48~1.52ms
• Td=(Ct*V sensing)/I charge (...Ct=33µF, Is=100µA)
2) TIMING CHART
MCLK
nRESET
20 MCLK
20 MCLK
5.461 ms
(65535 MCLK)
nPWRGD
HICLK
CLK falling
reRESETn
5.461 ms
(65535 MCLK)
RESETn
15 HCLK
3-2
Circuit Description
3-2-3 RISC MICROPROCESSOR
1) RISC MICROCESSOR PIN & INTERFACE(SPGPm)
Ball No
Pin No
Pin Name
I/O
Description
PAD
B1
1
SD15
I/O
SDRAM Bus Data[15]
BD8TARP_TC
C2
2
VSS_PLL1
-
VSS for Core PLL
-
D2
3
VDD_PLL1
-
VDD for Core PLL (1.8V)
-
D3
4
DATA0 / GPI1
I/O
ROM Bus Data[0] / GPI[1]
BD8TRP_FT
E4
5
MCLK
I
Core PLL Clock Input (12MHz)
TLCHT_TC
C1
6
DATA6 / GPI7
I/O
ROM Bus Data[6] / GPI[7]
BD8TRP_FT
D1
7
DATA1 / GPI2
I/O
ROM Bus Data[1] / GPI[2]
BD8TRP_FT
E3
8
DATA5 / GPI6
I/O
ROM Bus Data[5] / GPI[6]
BD8TRP_FT
E2
9
VDD_RING_OSC
-
VDD for Ring Oscillator (1.8V)
-
E1
10
DATA3 / GPI4
I/O
ROM Bus Data[3] / GPI[4]
BD8TRP_FT
F3
11
DATA9 / GPI10
I/O
ROM Bus Data[9] / GPI[10]
BD8TRP_FT
G4
12
GND
-
GROUND_RING
-
F2
13
DATA8 / GPI9
I/O
ROM Bus Data[8] / GPI[9]
BD8TRP_FT
F1
14
DATA7 / GPI8
I/O
ROM Bus Data[7] / GPI[8]
BD8TRP_FT
G3
15
DATA12 / GPI13
I/O
ROM Bus Data[12] / GPI[13]
BD8TRP_FT
G2
16
DATA11 / GPI12
I/O
ROM Bus Data[11] / GPI[12]
BD8TRP_FT
G1
17
DATA10 / GPI11
I/O
ROM Bus Data[10] / GPI[11]
BD8TRP_FT
H3
18
DATA4 / GPI5
I/O
ROM Bus Data[4] / GPI[5]
BD8TRP_FT
H2
19
DATA15 / GPI16
I/O
ROM Bus Data[15] / GPI[16]
BD8TRP_FT
H1
20
DATA14 / GPI15
I/O
ROM Bus Data[14] / GPI[15]
BD8TRP_FT
J4
21
VDD_CORE
-
VDD for CORE (1.8V)
-
J3
22
DATA19
I/O
ROM Bus Data[19]
BD8TRP_FT
J2
23
DATA18
I/O
ROM Bus Data[18]
BD8TRP_FT
J1
24
DATA17
I/O
ROM Bus Data[17]
BD8TRP_FT
K2
25
DATA16
I/O
ROM Bus Data[16]
BD8TRP_FT
K3
26
DATA22
I/O
ROM Bus Data[22]
BD8TRP_FT
K1
27
DATA13 / GPI14
I/O
ROM Bus Data[14] / GPI[14]
BD8TRP_FT
L1
28
DATA20
I/O
ROM Bus Data[20]
BD8TRP_FT
L2
29
DATA21
I/O
ROM Bus Data[21]
BD8TRP_FT
L3
30
DATA25
I/O
ROM Bus Data[25]
BD8TRP_FT
L4
31
DATA26
I/O
ROM Bus Data[26]
BD8TRP_FT
M1
32
DATA23
I/O
ROM Bus Data[23]
BD8TRP_FT
M2
33
DATA24
I/O
ROM Bus Data[24]
BD8TRP_FT
M3
34
DATA29
I/O
ROM Bus Data[29]
BD8TRP_FT
M4
35
DATA30
I/O
ROM Bus Data[30]
BD8TRP_FT
N1
36
DATA27
I/O
ROM Bus Data[27]
BD8TRP_FT
N2
37
DATA28
I/O
ROM Bus Data[28]
BD8TRP_FT
N3
38
VDD_ARM
-
VDD for ARM
-
P1
39
DATA31
I/O
ROM Bus Data[31]
BD8TRP_FT
P2
40
DATA2 / GPI3
I/O
ROM Bus Data[2] / GPI[3]
BD8TRP_FT
R1
41
VDD_CORE
-
VDD for CORE (1.8V)
-
P3
42
nROMCS2
O
ROM Bank2 Select_n
B4TR_TC
3-3
Circuit Description
Ball No
Pin No
Pin Name
I/O
Description
PAD
R2
43
nRD
O
ROM Bus Read_n
B4TR_TC
3-4
T1
44
nROMCS0
O
ROM Bank0 Select_n
B4TR_TC
P4
45
nROMCS3 / nIOCS3 /
GPO1
O
ROM Bank3 Select_n / IO Bank3
Select_n / GPO[1]
B4TR_TC
R3
46
nWR
O
ROM Bus Write_n
B4TR_TC
T2
47
nROMCS1
O
ROM Bank1 Select_n
B4TR_TC
U1
48
ADDR12
O
ROM Bus Addr[12]
B8TR_TC
T3
49
ADDR10
O
ROM Bus Addr[10]
B8TR_TC
U2
50
ADDR13
O
ROM Bus Addr[13]
B8TR_TC
V1
51
ADDR15
O
ROM Bus Addr[15]
B8TR_TC
T4
52
ADDR11
O
ROM Bus Addr[11]
B8TR_TC
U3
53
ADDR14
O
ROM Bus Addr[14]
B8TR_TC
V2
54
ADDR16
O
ROM Bus Addr[16]
B8TR_TC
W1
55
ADDR19
I/O
ROM Bus Addr[19]
BD8TRP_TC
V3
56
ADDR17
I/O
ROM Bus Addr[17]
BD8TRP_TC
W2
57
ADDR20
I/O
ROM Bus Addr[20]
BD8TRP_TC
Y1
58
nIOCS0
O
IO Bank0 Select_n
B4TR_TC
W3
59
ADDR21
I/O
ROM Bus Addr[21]
BD8TRP_TC
Y2
60
nIOCS1
O
IO Bank1 Select_n
B4TR_TC
W4
61
ADDR22
I/O
ROM Bus Addr[22]
BD8TRP_TC
V4
62
ADDR18
I/O
ROM Bus Addr[18]
BD8TRP_TC
U5
63
ADDR7
O
ROM Bus Addr[7]
B8TR_TC
Y3
64
VDD_CORE
O
VDD for CORE (1.8V)
-
Y4
65
nIOCS2 / nDACK0 /
GPO2
O
IO Bank2 Select_n / DMA IO Bank0
ACK_n / GPO[2]
B4TR_TC
V5
66
ADDR1
O
ROM Bus Addr[1]
B8TR_TC
W5
67
ADDR8
O
ROM Bus Addr[8]
B8TR_TC
Y5
68
ADDR9
O
ROM Bus Addr[9]
B8TR_TC
V6
69
ADDR4
O
ROM Bus Addr[4]
B8TR_TC
U7
70
ADDR6
O
ROM Bus Addr[6]
B8TR_TC
W6
71
ADDR2
O
ROM Bus Addr[2]
B8TR_TC
Y6
72
ADDR3
O
ROM Bus Addr[3]
B8TR_TC
V7
73
ADDR5
O
ROM Bus Addr[5]
B8TR_TC
W7
74
VDD_ARM
-
VDD for ARM Hard Macro(1.8V)
-
Y7
75
VDD_CORE
-
VDD for CORE (1.8V)
-
V8
76
EINT0 / TnRST
I
Ext. Interrupt0 / TAP Controller
Reset_n
SCHMITT_FT
W8
77
EINT1 / TCK
I
Ext. Interrupt1 / TAP Controller
Clock
SCHMITT_FT
Y8
78
EINT2 / nRXD2 / TMS
I
Ext. Interrupt2 / UART RX DATA[2] /
TAP Controller Mode Select
SCHMITT_FT
U9
79
EINT3 / nTXD2 / GPO9
I/O
Ext. Interrupt3 / UART TX Data[2] /
GPO[9]
BD4STRP_FT
V9
80
nRxD0
I
UART RX Data[0]
SCHMITT_FT
W9
81
nRxD1 / GPI17 / TDI
I
UART RX Data[1] / GPI[17] / TAP
Controller Data In
SCHMITT_FT
Y9
82
nTxD0
O
UART TX Data[0]
B4TR_TC
W10
83
TESTMODE
I
TESTMODE (Nomal : 0)
SCHMITT_TC
Circuit Description
Ball No
Pin No
Pin Name
I/O
Description
PAD
V10
84
nTxD1 / GPO10 / TDO
O
UART Tx Data[1] / GPO[10] / Tap
Controller Data Out
B4TR_TC
Y10
85
TESTSE
I
TESTSE (Normal : 0)
SCHMITT_TC
Y11
86
VDD_CORE
-
VDD for CORE (1.8V)
-
W11
87
RXERR / GPI25
I
MAC RX Error / GPI[25]
SCHMITT_TC
V11
88
GND
-
GROUND_RING
-
U11
89
RX_DV / GPI20
O
MAC RX Data Valid / GPI[20]
SCHMITT_TC
Y12
90
RXD0 / GPI21
O
MAC RX Data[0] / GPI[21]
SCHMITT_TC
W12
91
nLFPHB1 / nPRINT
O
Motor Out B_n / Print Start_n
B4TR_TC
V12
92
nLFPHB0 / nCMSG
O
Motor Out B / Command
Message_n
B4TR_TC
U12
93
nLFPHA0 / CCLK
O
Motor Out A / Communication Clock
B4TR_TC
Y13
94
RXD1 / GPI22
I
MAC RX Data[1] / GPI[22]
SCHMITT_TC
W13
95
VDO
O
Video Data Out
B8TR_TC
V13
96
SPD / nDREQ3
I/O
DIMM Detect / DMA REQ[3]_n
BD4SRTP_TC
Y14
97
nWAIT1 / CRS
I
Wait_n / MAC Carrier Sensor
SCHMITT_TC
W14
98
COL / EINT4
I
MAC Collision Detect / Ext.
Interrupt4
SCHMITT_TC
Y15
99
TX_EN
O
MAC TX Enable
B4TR_TC
V14
100
MDIO
I/O
MAC Management Data Inout
BD4STRUQP_TC
W15
101
TXD3 / GPO14
O
MAC TX Data[3] / GPO[14]
B4TR_TC
Y16
102
TXD2 / GPO13
O
MAC TX Data[2] / GPO[13]
B4TR_TC
U14
103
MDC / GPO15
O
MAC Management Data Clock /
GPO[15]
B4TR_TC
V15
104
TXCLK / GPI18
I
MAC TX Clock(25MHz) / GPI[18]
SCHMITT_TC
W16
105
TXD1 / GPO12
O
MAC TX Data[1] / GPO[12]
B4TR_TC
Y17
106
PD4
I/O
Parallel Port Data[4]
BD4STRP_FT
V16
107
TXD0 / nIOCS3
O
MAC TX Data[0] / IO Bank3
Select_n
B4TR_TC
W17
108
RXD3 / GPI24
I
MAC RX Data[3] / GPI[24]
SCHMITT_TC
Y18
109
PD2
I/O
Parallel Port Data[2]
BD4STRP_FT
U16
110
PD6
I/O
Parallel Port Data[6]
BD4STRP_FT
V17
111
RXD2
I
MAC RX Data[2] / GPI[23]
SCHMITT_TC
W18
112
PWMOUT2
O
PWM Output[2]
B4TR_TC
Y19
113
VCLK
I
Video Reference Clock
TLCHT_TC
V18
114
RXCLK / GPI19
I
MAC RX Clock(25MHz) / GPI[19]
SCHMITT_TC
W19
115
PD1
I/O
Parallel Port Data[1]
BD4STRP_FT
Y20
116
nINIT
I
Parallel Port Initialization_n
SCHMITT_FT
W20
117
VSS_ADC
-
VSS for ADC
-
V19
118
ATEST_OUT
O
ADC Test Output
ANA_TC
U19
119
AIN2
I
ADC Channel2 Input
ANA_TC
U18
120
AIN1
I
ADC Channel1 Input
ANA_TC
T17
121
AIN0
I
ADC Channel0 Input
ANA_TC
V20
122
VDD_ADC
-
Analog power for ADC (3.3V)
-
U20
123
VDD_CORE
-
VDD for CORE (1.8V)
-
T18
124
GND
-
GROUND_RING
-
T19
125
VDD_CORE
-
VDD for CORE (1.8V)
-
3-5
Circuit Description
Ball No
Pin No
Pin Name
I/O
Description
PAD
T20
126
VDD_CORE
-
VDD for CORE (1.8V)
-
R18
127
VBUS
I
USB Detect
SCHMITT_FT
P17
128
nLREADY / nEBSY
I
LSU Ready_n / Engine Busy_n
SCHMITT_FT
R19
129
nSELECTIN
I
Parallel Port Select Input_n
SCHMITT_FT
R20
130
LSUCLK / nCBSY /
GPO11
O
LSU Clock / Command Busy_n /
GPO[11]
B4TR_TC
P18
131
PD7
I/O
Parallel Port Data[7]
BD4STRP_FT
P19
132
PWMOUT1
O
PWM Output[1]
B4TR_TC
3-6
P20
133
PWMOUT0
O
PWM Output[0]
B4TR_TC
N18
134
nEMSG / nDACK3 /
PWMOUT3
I/O
Engine Message_n / DMA
ACK[3]_n / PWM Output[3]
BD4STRP_FT
N19
135
nFSYNC / nLFPHA1
I/O
Frame Sync_n / Motor Out A_n
BD4STRP_FT
N20
136
nHSYNC
I
Line Sync_n
SCHMITT_FT
M17
137
nSTROBE
I
Parallel Port Data Strobe_n
SCHMITT_FT
M18
138
PD5
I/O
Parallel Port Data[5]
BD4STRP_FT
M19
139
nWAIT0 / PDE
I/O
Wait_n / Parallel Port Data Enable
BD4STRP_TC
M20
140
nIOCS5 / nSCS4 /
GPO3 / TONEOUT
O
DRAM Bank4 / IO Bank5 Select_n /
GPO[3] / Tone Pulse Out
BD8TARP_TC
L19
141
PD3
I/O
Parallel Port Data[3]
BD4STRP_FT
L18
142
nFAULT
O
Parallel Port Fault_n
B4TR_TC
L20
143
nDREQ0 / GPI0 /
ADDR23
I/O
DMA REQ[0]_n / GPI[0] / ADDR[23]
BD4STRP_TC
K20
144
nRESET
I
External Reset_n Input
SCHMITT_TC
K19
145
PERROR
O
Parallel Port Paper Error
B4TR_TC
K18
146
nAUTOFD
I
Parallel Port Auto Feed_n
SCHMITT_FT
K17
147
nDACK2 / DQM7 /
GPO5
O
DMA ACK[2]_n / DQM[7] / GPO[5]
BD8TARP_TC
J20
148
nDREQ2 / DQM6 /
GPO6
I/O
DMA REQ[2]_n / DQM[6] / GPO[6]
BD8TARP_TC
J19
149
nDREQ1 / DQM4 /
GPO8
I/O
DMA REQ[1]_n / DQM[4] / GPO[8]
BD8TARP_TC
J18
150
VDD_CORE
-
VDD for CORE (1.8V)
-
J17
151
nSCS0
O
SDRAM Bank0 Select_n
BD8TARP_TC
H20
152
nSCS2
O
SDRAM Bank2 Select_n
BD8TARP_TC
H19
153
nCAS
O
SDRAM Column Address Select_n
BD8TARP_TC
H18
154
nSCS1
O
SDRAM Bank1 Select_n
BD8TARP_TC
G20
155
nIOCS4 / nSCS3 /
GPO4
O
IO Bank4 / SDRAM Bank3 Select_n
/ GPO[4]
BD8TARP_TC
G19
156
BUSY
O
Parallel Port Busy
B4TR_TC
F20
157
PD0
I/O
Parallel Port Data[0]
BD4STRP_FT
G18
158
SLCT_OUT
O
Parallel Port Selection Out
B4TR_TC
F19
159
nACK
O
Parallel Port Acknowledge_n
B4TR_TC
E20
160
nDACK1 / DQM5 /
GPO7
O
DMA ACK[1]_n / DQM[5] / GPO[7]
BD8TARP_TC
G17
161
nRSTOUT / CLKOUT /
GPO0
O
Internal Reset_n Out / Internal System Clock Out / GPO[0]
B8TR_TC
F18
162
SA7
O
SDRAM Bus Addr[7]
BD8TARP_TC
E19
163
SA9
O
SDRAM Bus Addr[9]
BD8TARP_TC
Circuit Description
Ball No
Pin No
Pin Name
I/O
Description
PAD
D20
164
VDD_USB
-
VDD for USB Hard Macro (1.8V)
-
E18
165
SA10
O
SDRAM Bus Addr[10]
BD8TARP_TC
D19
166
SA12
O
SDRAM Bus Addr[120
BD8TARP_TC
C20
167
BA0
O
SDRAM Bus Bank Select Addr[0]
BD8TARP_TC
E17
168
nRAS
O
SDRAM Row Address Select_n
BD8TARP_TC
D18
169
DQM2
O
SDRAM Bus DQM[2]
BD8TARP_TC
C19
170
DQM1
O
SDRAM Bus DQM[1]
BD8TARP_TC
B20
171
BA1
O
SDRAM Bus Bank Select Addr[1]
BD8TARP_TC
C18
172
DQM0
O
SDRAM Bus DQM[0]
BD8TARP_TC
B19
173
DQM3
O
SDRAM Bus DQM[3]
BD8TARP_TC
A20
174
RREF
I/O
USB PHY Register Reference
ANA_FT
A19
175
VSSL
-
VSS for Deserialisation Flip flops
-
B18
176
VDDL
-
VDD for Deserialisation Flip flops
(1.8V)
-
B17
177
VSSB
-
VSS for buffers
-
C17
178
DMNS
I/O
USB2 DATA-
ANA_FT
D16
179
DPLS
I/O
USB2 DATA+
ANA_FT
A18
180
VDD3_USB
-
VDD for USB1.1 FS compliance
(3.3V)
-
A17
181
VSSC
-
VSS for DLL and Xor tree
-
C16
182
VDDC
-
VDD for DLL and Xor tree (1.8V)
-
B16
183
VDDB
-
VDD for buffers (1.8V)
-
A16
184
VDD_USB
-
VDD for USB Hard Macro (1.8V)
-
C15
185
UCLK
I
USB PLL Input Clock (12MHz)
TLCHT_TC
D14
186
VSS_PLL2
-
VSS for USB PLL
-
B15
187
VDD_PLL2
-
VSS for USB PLL (1.8V)
-
A15
188
SA11
O
SDRAM Bus Addr[11]
BD8TARP_TC
C14
189
SA6
O
SDRAM Bus Addr[6]
BD8TARP_TC
B14
190
SA5
O
SDRAM Bus Addr[5]
BD8TARP_TC
A14
191
SA8
O
SDRAM Bus Addr[8]
BD8TARP_TC
C13
192
SA3
O
SDRAM Bus Addr[3]
BD8TARP_TC
B13
193
SA2
O
SDRAM Bus Addr[2]
BD8TARP_TC
A13
194
SA4
O
SDRAM Bus Addr[4]
BD8TARP_TC
D12
195
SA0
O
SDRAM Bus Addr[0]
BD8TARP_TC
C12
196
SA1
O
SDRAM Bus Addr[1]
BD8TARP_TC
B12
197
CKE
O
SDRAM Clock Enable
BD8TARP_TC
A12
198
nWE
O
SDRAM Write Enable_n
BD8TARP_TC
B11
199
SD30
I/O
SDRAM Bus Data[30]
BD8TARP_TC
C11
200
SD31
I/O
SDRAM Bus Data[31]
BD8TARP_TC
A11
201
SD29
I/O
SDRAM Bus Data[29]
BD8TARP_TC
A10
202
SD25
I/O
SDRAM Bus Data[25]
BD8TARP_TC
B10
203
SD26
I/O
SDRAM Bus Data[26]
BD8TARP_TC
C10
204
SD27
I/O
SDRAM Bus Data[27]
BD8TARP_TC
D10
205
SD28
I/O
SDRAM Bus Data[28]
BD8TARP_TC
A9
206
SD21
I/O
SDRAM Bus Data[21]
BD8TARP_TC
B9
207
SD22
I/O
SDRAM Bus Data[22]
BD8TARP_TC
3-7
Circuit Description
Ball No
Pin No
Pin Name
I/O
Description
PAD
C9
208
SD23
I/O
SDRAM Bus Data[23]
BD8TARP_TC
3-8
D9
209
SD24
I/O
SDRAM Bus Data[24]
BD8TARP_TC
A8
210
SD18
I/O
SDRAM Bus Data[18]
BD8TARP_TC
B8
211
SDCLK0
O
SDRAM Clock Output0
BD8TARP_TC
C8
212
SD20
I/O
SDRAM Bus Data[20]
BD8TARP_TC
A7
213
SD14
I/O
SDRAM Bus Data[14]
BD8TARP_TC
B7
214
SD19
I/O
SDRAM Bus Data[19]
BD8TARP_TC
A6
215
SD11
I/O
SDRAM Bus Data[11]
BD8TARP_TC
C7
216
SD16
I/O
SDRAM Bus Data[16]
BD8TARP_TC
B6
217
SDCLK1
O
SDRAM Clock Output1
BD8TARP_TC
A5
218
SD12
I/O
SDRAM Bus Data[12]
BD8TARP_TC
D7
219
SD17
I/O
SDRAM Bus Data[17]
BD8TARP_TC
C6
220
SD13
I/O
SDRAM Bus Data[13]
BD8TARP_TC
B5
221
SD8
I/O
SDRAM Bus Data[8]
BD8TARP_TC
A4
222
SD5
I/O
SDRAM Bus Data[5]
BD8TARP_TC
C5
223
SD9
I/O
SDRAM Bus Data[9]
BD8TARP_TC
B4
224
SD6
I/O
SDRAM Bus Data[6]
BD8TARP_TC
A3
225
SD3
I/O
SDRAM Bus Data[3]
BD8TARP_TC
D5
226
SD10
I/O
SDRAM Bus Data[10]
BD8TARP_TC
C4
227
SD7
I/O
SDRAM Bus Data[7]
BD8TARP_TC
B3
228
SD4
I/O
SDRAM Bus Data[4]
BD8TARP_TC
B2
229
SD1
I/O
SDRAM Bus Data[1]
BD8TARP_TC
A2
230
SD0
I/O
SDRAM Bus Data[0]
BD8TARP_TC
C3
231
SD2
I/O
SDRAM Bus Data[2]
BD8TARP_TC
Circuit Description
2) RISC MICROCESSOR PIN & INTERFACE(CIP4)
No
Pin Name
I/O
Description
Pad Type
Current drive
1
GND2
P
Vss Supply
vss2i
-
2
NTEST
I
Nand Tree Test Mode Selection
pticd
-
3
TM
I
Global Test Mode Selection
pticd
-
4
TEST1
I
Test Mode Selection 1
pticd
-
5
GND17
P
Vss Supply
vss3op
-
6
TEST2
I
Test Mode Selection 2
pticd
-
7
XDACK1
I
DMA Acknowledge Signal 1
ptis
-
8
XDREQ1
O
DMA Request Signal 1
phob4
4mA
9
VDD1
P
Vdd Supply
vdd2i
-
10
XDACK2
I
DMA Acknowledge Signal 2
ptis
-
11
XDREQ2
O
DMA Request Signal 2
phob4
4mA
12
XDACK3
I
DMA Acknowledge Signal 3
ptis
-
13
XDREQ3
O
DMA Request Signal 3
phob4
4mA
14
nRESET
I
Global Reset
ptis
-
15
CLK_OUT
O
PLL Clock Out
phob12
12mA
16
GND3
P
Vss Supply
vss2i
-
17
XP
I
Clock Oscillation Input
phsoscm26
10~40MHz
18
XPOUT
O
Clock Oscillation Output
phsoscm26
10~40MHz
19
GNDD16
P
Vss Supply
vss2t_abb
-
20
FILTER*
O
PLL Filter Pump Out
poar50_abb
-
21
GND1
P
Vss Supply
vbb_abb
-
22
VDDA9,VDDD9
P
Vdd Supply
vdd2t_abb
-
23
GND24,GND33
P
Vss Supply
vss3t_abb
-
24
RTC_XO
O
RTC Clock Oscillation Output
poar50_abb
-
25
RTC_XI
I
RTC Clock Oscillation Input
piar50_abb
-
26
VDD8,VDD18
P
Vdd Supply
vdd3t_abb
-
27
IRQ
O
Interrupt Request Signal
phob4
4mA
28
nCS
I
CIP4 Chip Select
ptis
-
29
GND4
P
Vss Supply
vss2i
-
30
nRD
I
CIP4 CPU Read Control
ptis
-
31
nWR
I
CIP4 CPU Write Control
ptis
-
32
BA1
I
Bank Address Bus [1]
ptis
-
33
BA0
I
Bank Address Bus [0]
ptis
-
34
GND19
P
Vss Supply
vss3op
-
35
A5
I
CPU Address Bus [5]
ptis
-
36
A4
I
CPU Address Bus [4]
ptis
-
37
A3
I
CPU Address Bus [3]
ptis
-
38
VDD2
P
Vdd Supply
vdd2i
-
39
A2
I
CPU Address Bus [2]
ptis
-
40
A1
I
CPU Address Bus [1]
ptis
-
41
A0
I
CPU Address Bus [0]
ptis
-
42
GND5
P
Vss Supply
vss2i
-
43
D31
B
CPU Data Bus [31]
phbst8
8mA
3-9
Circuit Description
No
Pin Name
I/O
Description
Pad Type
Current drive
44
D30
B
CPU Data Bus [30]
phbst8
8mA
45
D29
B
CPU Data Bus [29]
phbst8
8mA
46
D28
B
CPU Data Bus [28]
phbst8
8mA
47
GND20
P
Vss Supply
vss3op
-
48
D27
B
CPU Data Bus [27]
phbst8
8mA
49
D26
B
CPU Data Bus [26]
phbst8
8mA
50
D25
B
CPU Data Bus [25]
phbst8
8mA
51
VDD11
P
Vdd Supply
vdd3op
-
52
D24
B
CPU Data Bus [24]
phbst8
8mA
53
D23
B
CPU Data Bus [23]
phbst8
8mA
54
D22
B
CPU Data Bus [22]
phbst8
8mA
55
D21
B
CPU Data Bus [21]
phbst8
8mA
56
GND6
P
Vss Supply
vss2i
-
57
D20
B
CPU Data Bus [20]
phbst8
8mA
58
D19
B
CPU Data Bus [19]
phbst8
8mA
59
D18
B
CPU Data Bus [18]
phbst8
8mA
60
GND21
P
Vss Supply
vss3op
-
61
D17
B
CPU Data Bus [17]
phbst8
8mA
62
D16
B
CPU Data Bus [16]
phbst8
8mA
63
D15
B
CPU Data Bus [15]
phbst8
8mA
64
D14
B
CPU Data Bus [14]
phbst8
8mA
65
VDD3
P
Vdd Supply
vdd2i
-
66
D13
B
CPU Data Bus [13]
phbst8
8mA
67
D12
B
CPU Data Bus [12]
phbst8
8mA
68
D11
B
CPU Data Bus [11]
phbst8
8mA
69
GND7
P
Vss Supply
vss2i
-
70
D10
B
CPU Data Bus [10]
phbst8
8mA
71
D9
B
CPU Data Bus [9]
phbst8
8mA
72
D8
B
CPU Data Bus [8]
phbst8
8mA
73
D7
B
CPU Data Bus [7]
phbst8
8mA
74
GND22
P
Vss Supply
vss3op
-
75
D6
B
CPU Data Bus [6]
phbst8
8mA
76
D5
B
CPU Data Bus [5]
phbst8
8mA
77
D4
B
CPU Data Bus [4]
phbst8
8mA
78
VDD12
P
Vdd Supply
vdd3op
-
79
D3
B
CPU Data Bus [3]
phbst8
8mA
80
D2
B
CPU Data Bus [2]
phbst8
8mA
81
D1
B
CPU Data Bus [1]
phbst8
8mA
82
D0
B
CPU Data Bus [0]
phbst8
8mA
83
GND8
P
Vss Supply
vss2i
-
84
TX_EN1
O
Motor Control Tx Enable 1
phob4
4mA
85
TX_EN2
O
Motor Control Tx Enable 2
phob4
4mA
86
TX_A
O
Motor Control Tx Channel A
phob4
4mA
87
TX_B
O
Motor Control Tx Channel B
phob4
4mA
88
GND23
P
Vss Supply
vss3op
-
3-10
Circuit Description
No
Pin Name
I/O
Description
Pad Type
Current drive
89
nTX_A
O
Motor Control Tx Channel A
phob4
4mA
90
nTX_B
O
Motor Control Tx Channel A
phob4
4mA
91
MOTOR_POL
I
Motor Polarity
ptis
4mA
92
VDD4
P
Vdd Supply
vdd2i
-
93
PItg1
O
CIS/CCD PItg1 Signal
phob8
8mA
94
PI1
O
CIS/CCD PI1 Signal
phob8
8mA
95
PI2
O
CIS/CCD PI2 Signal
phob8
8mA
96
GND9
P
Vss Supply
vss2i
-
97
PIrs
O
CIS/CCD PIrs Signal
phob8
8mA
98
PIcp
O
CIS/CCD PIsh Signal
phob8
8mA
99
ADC_CLK
O
AFE ADC Clock
phob8
8mA
100
VDD13
P
Vdd Supply
vdd3op
-
101
CDS2_CLK
O
AFE CDS2 Clock
phob8
8mA
102
SCLK1
O
AFE SIO Sync. Clock
phob8
8mA
103
SLOAD1
O
AFE SIO Read/Write Control Signal
phob8
8mA
104
VDD10
P
Vdd Supply
vdd3op
-
105
SDO1
O
AFE SIO Serial Output 1
phob8
8mA
106
SDIO1
B
AFE SIO Serial Inout/Output 1
phbst8
8mA
107
SDIO2
B
AFE SIO Serial Inout/Output 2
phbst8
8mA
108
GND10
P
Vss Supply
vss2i
-
109
AFE_D9
I
A/D Converted Data Bus [9]
ptis
-
110
AFE_D8
I
A/D Converted Data Bus [8]
ptis
-
111
AFE_D7
I
A/D Converted Data Bus [7]
ptis
-
112
AFE_D6
I
A/D Converted Data Bus [6]
ptis
-
113
VDD5
P
Vdd Supply
vdd2i
-
114
AFE_D5
I
A/D Converted Data Bus [5]
ptis
-
115
AFE_D4
I
A/D Converted Data Bus [4]
ptis
-
116
AFE_D3
I
A/D Converted Data Bus [3]
ptis
-
117
GND25
P
Vss Supply
vss3op
-
118
AFE_D2
I
A/D Converted Data Bus [2]
ptis
-
119
AFE_D1
I
A/D Converted Data Bus [1]
ptis
-
120
AFE_D0
I
A/D Converted Data Bus [0]
ptis
-
121
GND11
P
Vss Supply
vss2i
-
122
SRAM_A15
O
SRAM Address Bus [15]
phob8
8mA
123
SRAM_A14
O
SRAM Address Bus [14]
phob8
8mA
124
SRAM_A13
O
SRAM Address Bus [13]
phob8
8mA
125
SRAM_A12
O
SRAM Address Bus [12]
phob8
8mA
126
VDD14
P
Vdd Supply
vdd3op
-
127
SRAM_A11
O
SRAM Address Bus [11]
phob8
8mA
128
SRAM_A10
O
SRAM Address Bus [10]
phob8
8mA
129
SRAM_A9
O
SRAM Address Bus [9]
phob8
8mA
130
GND26
P
Vss Supply
vss3op
-
131
SRAM_A8
O
SRAM Address Bus [9]
phob8
8mA
132
SRAM_A7
O
SRAM Address Bus [9]
phob8
8mA
133
SRAM_A6
O
SRAM Address Bus [9]
phob8
8mA
3-11
Circuit Description
No
Pin Name
I/O
Description
Pad Type
Current drive
134
SRAM_A5
O
SRAM Address Bus [9]
phob8
8mA
135
GND12
P
Vss Supply
vss2i
-
136
SRAM_A4
O
SRAM Address Bus [9]
phob8
8mA
137
SRAM_A3
O
SRAM Address Bus [9]
phob8
8mA
138
SRAM_A2
O
SRAM Address Bus [9]
phob8
8mA
139
SRAM_A1
O
SRAM Address Bus [9]
phob8
8mA
140
VDD6
P
Vdd Supply
vdd2i
-
141
SRAM_A0
O
SRAM Address Bus [9]
phob8
8mA
142
SRAM_nWR
O
SRAM Write Enable Signal
phob8
8mA
143
SRAM_D15
B
SRAM Data Bus [15]
phbst8
8mA
144
SRAM_D14
B
SRAM Data Bus [14]
phbst8
8mA
145
GND27
P
Vss Supply
vss3op
-
146
SRAM_D13
B
SRAM Data Bus [13]
phbst8
8mA
147
SRAM_D12
B
SRAM Data Bus [12]
phbst8
8mA
148
SRAM_D11
B
SRAM Data Bus [11]
phbst8
8mA
149
GND13
P
Vss Supply
vss2i
-
150
SRAM_D10
B
SRAM Data Bus [10]
phbst8
8mA
151
SRAM_D9
B
SRAM Data Bus [9]
phbst8
8mA
152
SRAM_D8
B
SRAM Data Bus [8]
phbst8
8mA
153
SRAM_D7
B
SRAM Data Bus [7]
phbst8
8mA
154
VDD15
P
Vdd Supply
vdd3op
-
155
SRAM_D6
B
SRAM Data Bus [6]
phbst8
8mA
156
SRAM_D5
B
SRAM Data Bus [5]
phbst8
8mA
157
SRAM_D4
B
SRAM Data Bus [4]
phbst8
8mA
158
GND28
P
Vss Supply
vss3op
-
159
SRAM_D3
B
SRAM Data Bus [3]
phbst8
8mA
160
SRAM_D2
B
SRAM Data Bus [2]
phbst8
8mA
161
SRAM_D1
B
SRAM Data Bus [1]
phbst8
8mA
162
SRAM_D0
B
SRAM Data Bus [0]
phbst8
8mA
163
GND14
P
Vss Supply
vss2i
-
164
GPO7/PItg2
O
General Purpose Output [7]
phob8
8mA
165
GPO6/RLED
O
General Purpose Output [6]
phob8
8mA
166
GPO5/GLED
O
General Purpose Output [5]
phob8
8mA
167
GPO4/BLED
O
General Purpose Output [4]
phob8
8mA
168
VDD7
P
Vdd Supply
vdd2i
-
169
GPO3/PItg3
O
General Purpose Output [3]
phob8
8mA
170
GPO2/PIsh
O
General Purpose Output [2]
phob8
8mA
171
GPO1/
LEVEL_SHIFT
O
General Purpose Output [1]
phob8
8mA
172
GPO0
O
General Purpose Output [0]
phob8
8mA
173
GND29
P
Vss Supply
vss3op
8mA
174
GPIO2B/AFE_D11
B
General Purpose Input/Output 2 [11]
phbst8
8mA
175
GPIO2A/AFE_D10
B
General Purpose Input/Output 2 [10]
phbst8
-
176
GPIO29/AFE_D9
B
General Purpose Input/Output 2 [9]
phbst8
8mA
177
GND30
P
Vss Supply
vss3op
8mA
178
GPIO28/AFE_D8
B
General Purpose Input/Output 2 [8]
phbst8
8mA
3-12
Circuit Description
No
Pin Name
I/O
Description
Pad Type
Current drive
179
GPIO27/AFE_D7
B
General Purpose Input/Output 2 [7]
phbst8
8mA
180
GPIO26/AFE_D6
B
General Purpose Input/Output 2 [6]
phbst8
-
181
GPIO25/AFE_D5
B
General Purpose Input/Output 2 [5]
phbst8
8mA
182
VDD16
P
Vdd Supply
vdd3op
8mA
183
GPIO24/AFE_D4
B
General Purpose Input/Output 2 [4]
phbst8
8mA
184
GPIO23/AFE_D3
B
General Purpose Input/Output 2 [3]
phbst8
8mA
185
GPIO22/AFE_D2
B
General Purpose Input/Output 2 [2]
phbst8
8mA
186
GND15
P
Vss Supply
vss2i
8mA
187
GPIO21/AFE_D1
B
General Purpose Input/Output 2 [1]
phbst8
8mA
188
GPIO20/AFE_D0
B
General Purpose Input/Output 2 [0]
phbst8
8mA
189
GPIO1F/
SRAM_D15
B
General Purpose Input/Output 1 [15]
phbst8
8mA
190
GPIO1E/
SRAM_D14
B
General Purpose Input/Output 1 [14]
phbst8
-
191
GND31
P
Vss Supply
vss3op
8mA
192
GPIO1D/
SRAM_D13
B
General Purpose Input/Output 1 [13]
phbst8
8mA
193
GPIO1C/
SRAM_D12
B
General Purpose Input/Output 1 [12]
phbst8
-
194
GPIO1B/
SRAM_D11
B
General Purpose Input/Output 1 [11]
phbst8
4mA
195
GPIO1A/
SRAM_D10
B
General Purpose Input/Output 1 [10]
phbst8
-
196
VDD17
P
Vdd Supply
vdd3op
197
GPIO19/SRAM_D9
B
General Purpose Input/Output 1 [9]
phbst8
198
GPIO18/SRAM_D8
B
General Purpose Input/Output 1 [8]
phbst8
199
GPIO17/SRAM_D7
B
General Purpose Input/Output 1 [7]
phbst8
200
GND32
P
Vss Supply
vss3op
201
GPIO16/SRAM_D6
B
General Purpose Input/Output 1 [6]
phbst8
-
202
GPIO15/SRAM_D5
B
General Purpose Input/Output 1 [5
phbst8
-
203
GPIO14/SRAM_D4
B
General Purpose Input/Output 1 [4]
phbst8
-
204
GPIO13/SRAM_D3
B
General Purpose Input/Output 1 [3]
phbst8
-
205
GND18
P
Vss Supply
vss3op
-
206
GPIO12/SRAM_D2
B
General Purpose Input/Output 1 [2]
phbst8
-
207
GPIO11/SRAM_D1
B
General Purpose Input/Output 1 [1]
phbst8
-
208
GPIO10/SRAM_D0
B
General Purpose Input/Output 1 [0]
phbst8
-
3-13
Circuit Description
3-2-4 PROGRAM ROM (FLASH MEMORY) CONTROL
1) DEVICE
TYPE No.
AM29LU160DB
CAPACITY
4 MBYTE (1MB * 16BITS * 2)
2) PROGRAMMING
BEFORE ASS’Y
EPROM PROGRAMMER or PROGRAMMING at the factory
AFTER ASS’Y
DOWNLOAD from PC
3) OPERATING PRINCIPLE
When the RCSO(ROM CHIP SELECT)signal is activated from the CPU after the POWER is ON, it activates RD SIGNAL and reads the DATA(HIGH/LOW) stored in the FLASH MEMORY to control the overall system. The FLASH MEMORY may also write. When turning the power on, press and hold the key(power
switch) for 2 - 3 seconds, then the LED will scroll and the PROGRAM DOWNLOAD MODE will be activated.
In this mode, you can download the program through the parallel port.
AC CHARACTERISTICS
Read Status Data (last two cycles)
Program Command Sequence (last two cycles)
tAS
tWC
Addresses
555h
PA
PA
PA
tAH
CE#
tCH
OE#
tWHWH1
tWP
WE#
tWPH
tCS
tDS
tDH
PD
A0h
Data
Status
DOUT
tBUSY
tRB
RY/BY#
tVCS
VCC
Notes:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
2. Illustration shows device in word mode.
Figure 17.
Program Operation Timings
CE#
The falling edge of the last WE# signal
WE#
BYTE
tSET
(tAS)
tHOLD (tAH)
Note: Refer to the Erase/Program Operations table for tAS and tAH specifications.
Figure 16.
3-14
BYTE# Timings for Write Operations
Circuit Description
3-2-5 DRAM CONTROL
1) DEVICE
TYPE NO.
K4S
CAPACITY
16MBYTES (1M * 16BITS * 4Bank * 2)
2) OPERATING PRINCIPLE
DRAM can either read or write. The data can be stored in the DRAM only when the power is on. It stores
data white the CPU processes data. The address to read and write the data is specified by RAS SIGNAL
and CAS SIGNAL. DRAMWE*SIGNAL is activated when writing data and DRAMOE*SIGNAL, when reading. You can expand up to 64MBYTE of DRAM in this system.
Start Address ~ End Address
Contents
0x00000000 ~ 0x00FFFFFF
ROM Bank0
0x01000000 ~ 0x01FFFFFF
ROM Bank1
0x02000000 ~ 0x02FFFFFF
ROM Bank2
0x03000000 ~ 0x03FFFFFF
ROM Bank3
0x04000000 ~ 0x0FFFFFFF
Unused
0x10000000 ~ 0x1FFFFFFF
Special Function Registers
0x20000000 ~ 0x20FFFFFF
I/O Bank0
0x21000000 ~ 0x21FFFFFF
I/O Bank1
0x22000000 ~ 0x22FFFFFF
I/O Bank2
0x23000000 ~ 0x23FFFFFF
I/O Bank3
0x24000000 ~ 0x24FFFFFF
I/O Bank4
0x25000000 ~ 0x25FFFFFF
I/O Bank5
0x26000000 ~ 0x26FFFFFF
DMA I/O Bank0
0x27000000 ~ 0x27FFFFFF
DMA I/O Bank1
0x28000000 ~ 0x28FFFFFF
DMA I/O Bank2
0x29800000 ~ 0x29FFFFFF
DMA I/O Bank3
0x2A000000 ~ 0x2FFFFFFF
Unused
0x30000000 ~ 0x30FFFFFF
RSH SRAM
0x31000000 ~ 0x31FFFFFF
HPVC SRAM
0x32000000 ~ 0x32FFFFFF
MOTOR SRAM
0x33000000 ~ 0x37FFFFFF
Unused
0x38000000 ~ 0x38FFFFFF
USB CSR & FIFO
0x39000000 ~ 0x390003FF
USB PLUG DETECT
0x38000500 ~ 0x3FFFFFFF
Unused
0x40000000 ~ 0x4FFFFFFF
SDRAM array0 (bank 0)
0x50000000 ~ 0x5FFFFFFF
SDRAM array1 (bank 1)
0x60000000 ~ 0x6FFFFFFF
SDRAM array2 (bank 2)
0x70000000 ~ 0x7FFFFFFF
SDRAM array3 (bank 3)
0x80000000 ~ 0xBFFFFFFF
SDRAM array0~4 (Mirror)
0xC0000000 ~ 0xC00007FF
MAC
0xC0000800 ~ 0xC0FFFFFF
Unused
3-15
Circuit Description
3-2-5-1 SDRAM DRAM read timing
Basically the Extended Data Out DRAM is similar to Fast Page Mode DRAM. For FPM, the data are valid only
when the nCAS is active while reading the internal data, however, it has a latch that the data will be
continuously outputted even after the nCAS is inactivated.
While configuring the software, you must set the timing register of SFR considering the clock speed and the
DRAM spec.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLOCK
HIGH
CKE
*Note 1
CS
RAS
*Note 2
CAS
ADDR
RAa
RBb
RAa
RBb
CAa
RCc
CBb
RDd
CCc
CDd
BA0
BA1
A10/AP
RCc
RDd
QAa0 QAa1 QAa2 QBb0
CL=2
QBb1 QBb2 QCc0 QCc1 QCc2 QDd0 QDd1 QDd2
DQ
CL=3
QAa0 QAa1 QAa2 QBb0
QBb1 QBb2 QCc0 QCc1 QCc2 QDd0 QDd1 QDd2
WE
DQM
Row Active
(A-Bank)
Read
(A-Bank)
Row Active
(B-Bank)
Read
(B-Bank)
Row Acive
(C-Bank)
Read
(C-Bank)
Precharge
(D-Bank)
Precharge
(C-Bank)
(D-Bank)
Precharge
(A-Bank)
Read
(D-Bank)
Precharge
(B-Bank)
: Don't care
* Note : 1. CS can be don’t cared when RAS, CAS and WE are hih at the clock high going dege.
2. To interrupt a burst read by row precharge, both the read and the precharge banks must be the
same.
3-16
Circuit Description
3-2-5-2 SDRAM write timing
CLOCK
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
HIGH
CKE
CS
RAS
CAS
ADDR
RAa
RBb CAa
CBb RCc
RDd CCc
CDd
BA0
BA1
*Note 2
A10/AP
RAa
DQ
RCc
RBb
RDd
DAa0 DAa1 DAa2 DAa3 DBb0 DBb1 DBb2 DBb3 DCc0 DCc1 DDd0 DDd1 DDd2
tCDL
tRDL
WE
*Note 1
DQM
Row Active
(A-Bank)
Write
(A-Bank)
Row Active
(B-Bank)
Write
(B-Bank)
Row Active
(C-Bank)
Row Active
(D-Bank)
Write
(D-Bank)
Precharge
(All Banks)
Write
(C-Bank)
: Don't care
*Note : 1. To interrupt burst write by Row precharge, DQM should be asserted to mask invalid input data.
2. To interrupt burst wrige by Row precharge, both the write and the prechargebanks must be the
same.
3-17
Circuit Description
3-2-6 FS781 (FREQUENCY ATTENUATOR)
This system used FS741 for the main clock for EMI SUPPRESSION.
It spreads the source clock in a consistent bandwidth to disperse the energy gathered in order to attenuate
the energy.
The capacitor value of the loop filter(PIN 4) is set depending on the source clock used or the spread bandwidth. Refer to FS781 Spec. for detail.
3-2-7 USB (Universal Serial Bus)
NS’s USBN9602 is used as the interface IC and 48MHz clock is used.
When the data is received through the USB port, EIRQ1 SIGNAL is activated to send interrupt to CPU,
then it directly sends the data to DRAM by IOCS4*&DRAMA(11) SIGNAL through DRAMD (24;31).
3-2-8 SRAM : 1MByte SRAM K6F1008U2C
It stores a variety of option data.
3-2-9 FAX Transceiver
3-2-9-1. GENERAL
This circuit processes transmission signals of modem and between LIU and modem.
3-2-9-2. modem (u44)
FM336 is a single ship fax modem. It has functions of DTMF detection and DTMF signal production as well as
functioins of modem. TX A1, 2 is transmission output port and RX IN is received data input port. / POR signal
controlled by MFP controller (U3:ARM946ES) can initialize modem (/M_RST) without turning off the system.
D0-D7 are 8-bit data buses. RS0-RS4 signals to select the register in modem chips. /RS and /WR signals control READ and WRITE respectively. /IRQ is a signal for modem interrupt.
Transmission speed of FM336 is supported up to 33.6k.
The modem is connected to LINE through transformer directly.
< FAX TRANSCEIVER >
3-18
Circuit Description
3-3 Scanner
3-3-1 SUMMARY
This flat-bed type device to read manuscripts has 600dpi CCD as an image sensor. There is one optical sensor for detecting CCD home position and Scan-end position. The home position is detected by a optical sensor which is attached to the CCD Module. The Scan-end position is calculated by numer of motor step.
CCD
Charge Coupled Device improves productivity and allows a compact design.
This machine uses a color CCD.
• Minimum Scan Line Time for One Color : 2.5mSec
• Light Source Power : +18V
• Maximum Pixel frequency : 10MHz
• Effective Sensor Element : 5340 X 3
• Clamp Level : 0.7~ 0.8V
• Bright Output : MIN 0.8V
AIN
PI_TG
AD C_REF T
ADC _REFB
12-bit
PI1
EXT SRAM
PI2
Sen so r
Shadi ng
Interface
Acqu isitio n
A/ D converter
AFE_CIP4
Vertical
D ecim ation
Shadi ng
C orrectio n
SRAM
1 024 x 8
( R/G/ B)
SRAM_A[ 15:0]
SRAM_D[ 15: 0]
SRAM_nRD
SRAM_nWR
Gam ma
C orrectio n
SRAM
8 192 x 8
( 2l ine)
Imag e
SRAM
Processing
256 x 8
Enlarge men t
Mo dule
/ Redu ction
SRAM
4 09 6 x16
(2 line )
IRQ
Vp eak
Contro l
Interrupt
Contro l
Mo to r
Con tro l
TX_A, B
n TX_A, B
TX_EN1, EN2
D MA
n CS
CPU I/F
CIP4
Mod ule
Register
n RD
n WR
A [ 5 : 0]
D [ 15 : 0]
Interface
SRAM
1 024 x 8
n XDREQ
n XDACK
<Block Diagram>
3-19
Circuit Description
3-3-2 Key Features
Overview
(1) 0.5µm C-MOS process(TLM), 208-PIN QFP, STD85 library
(2) Frequency : Max PLL 80 MHz
(3) On-Chip oscillator
(4) Method : Raster scanning method
(5) Image Sauce : 300/400/600dpi CIS & CCD
(6) Scanning Mode
• color gray image: each 8 bits / RGB
• mono gray image: 8 bits / pixel
• binary image: 1 bit / pixel (for text/phoot/mixed mode)
(7) Maximum scanning width : A3, 600dpi (8K effective pixels)
(8) Ideal MSLT (A4, 600/300dpi)
• color gray image: 3x5Kx80nsec = 1.2msec (7/28 CPM)
• mono gray image: 1x5Kx80nsec = 0.4msec (21/84 CPM)
• binary image: 1x5Kx80nsec = 0.4msec (21/84 CPM)
(9) A/D conversion depth : 12bits
Pixel processing structure
• Minimum pixel processing time : 4 system clocks
• High speed pipelined processing method
(Shading correction, Gamma correction, Enlargement/Reducement, and Binarization)
Shading Correction
(1) White shading correction support for each R/G/B
(2) White shading data memory : 3x8Kx12bits = 288Kbits
(3) Black shading data memory : 3x8Kx12bits = 288Kbits
384Kbits (external)
384Kbits (external)
Gamma Correction
(1) Independent Gamma table for each RGB component
(2) Gamma table data memory : 3x1Kx8bits = 24Kbits (internal)
Binarization (mono)
(1) 256 Gray’s halftone representation for Photo document : 3x5 EDF(Error DifFusion) method proposed by
Stucki.
(2) LAT(Local Adaptive Thresholding) for Text document :
• use of 5x5 LOCAL WINDOW (TIP ALGORITHM)
• ABC(Automatic Background Control) :Tmin Automatic change
(3) Mixed mode processing for text/photo mixed document
(4) EDF data memory : 2x4Kx16bits = 128Kbits (internal)
(5) LAT data memory : 4x4Kx16bits = 256Kbits (external)
Scaling of input image
(1) Scaling factor
• Horizontal direction: 25 ~ 800% by 1% unit
• Vertical direction: 25 ~ 100% by 1% unit
(2) Scaling data memory : 2x8Kx8bits = 128Kbits (internal)
3-20
Circuit Description
Intelligent scan motor controlloer
(1) Automatic acceleration/deceleration/uniform velocity
(2) Data memory : 256x16bits = 4Kbits (internal)
Auto-Run
Automatic CLK_LINE (line processing start control) and •’TG (line scan start control) signal generation|
(1)Available resynchronization of øTG signal
(2) programmable øTG’s period & CLK_LINE’s occurrence number
Processed data output format in DTM(Data Transfer Module)
(1)DMA mode : Burst/On-demand mode
(2) CDIP I/F : LINE_SYNC, PIXEL_SYSNC, PIXEL_DATA[7:0]
36 General Purpose Input/Output : 8(GPO), 28(GPIO)
Black/White reversion, and Image Mirroring support
ADD R BU S
DATA MEMORY
DMA Controller
DATA BUS
IW IN
Scan/Motor
Driver
T
R
D
M
A
T
R
D
M
A
Image
A
C
K
R
E
Q
Processor
_
CLK_PIX
L IN E_PERIO D
SRAM
_
CLK_LINE
CPU
SPGPm
1M bit
(SPGPm)
ADC _CLK
CD S2 _CLK
AFE Co ntro l
AFE
12b it ADC
Sig na l
12 b it (R/ G/ B)
ADD R- BUS
ADDR- BUS
Ana lo g Si gn al
PI_TG
PI1 , PI2
DAT A- BUS
Tx_A, Tx_B,
DAT A- BUS
Scanner
n Tx_A, nTx_B
CIP4
D OCU MENT IMAGE
<External interfce with CIP4>
3-21
Circuit Description
AIN
PI_TG
ADC_REFT
ADC_REFB
12-bit
PI1
EXT SRAM
PI2
Sen so r
Shadi ng
Interface
Acqu isitio n
A/ D converter
AFE_CIP4
Vertical
Decimation
Shadi ng
Correctio n
SRAM
1 024 x 8
( R/G/ B)
SRAM_A[ 15:0]
SRAM_D[ 15: 0]
SRAM_nRD
SRAM_nWR
Gam ma
Correctio n
SRAM
8 192 x8
( 2l ine)
Imag e
SRAM
Processing
256 x 8
Enlarge men t
Mo dule
/ Redu ction
SRAM
4096 x16
(2 line )
IRQ
Interrupt
Contro l
Vp eak
Contro l
Mo to r
Con tro l
TX_A, B
nTX_A, B
TX_EN1, EN2
DMA
nCS
CPU I/F
CIP4
Mod ule
Register
nRD nWR
A[5:0]
Interface
SRAM
1 024 x 8
D [15:0]
nXDREQ
nXDACK
<Block diagram of CIP4>
3-22
Circuit Description
3-4 HOST INTERFACE:
Referred to IEEE 1284 standard.
3-4-1. Host Interface
PARALLEL PORT INTERFACE PART ARM946ES has the Parallel Port Interface Part that enables Parallel
Interface with PC. This part is connected to PC through Centronics connector. It generates major control
signals that are used to actuate parallel communication. It is comprised of/ERROR, PE, BUSY, /ACK,
SLCT, /INIT, /SLCTIN, /AUTOFD and /STB. This part and the PC data transmission method support the
method specified in IEEE P1283 Parallel Port Standard (http://www.fapo.com/ieee1284.html). In other
words, it supports both compatibility mode (basic print data transmitting method), the nibble mode
(4bit data; supports data uploading to PC) and ECP (enhanced capabilities port: 8bits data - high speed
two-way data transmission with PC). Compatibility mode is generally referred to as the Centronics mode
and this is the protocol used by most PC to transmit data to the printer. ECP mode is an improved protocol for the communication between PC and peripherals such as printer and scanner, and it provides
high speed two-way data communication. ECP mode provides two cycles in the two-way data transmission; data cycle and command cycle. The command cycle has two formats; Run-Length Count and Channel Addressing. RLE (Run-Length Count) has high compression rate (64x) and it allows real-time data
compression that it is useful for the printer and scanner that need to transmit large raster image that has a
series of same data. Channel Addressing was designed to address multiple devices with single structure. For example, like this system, when the fax/printer/scanner have one structure, the parallel port can be
used for other purposes while the printer image is being processed.This system uses RLE for high speed
data transmission. PC control signals and data send/receive tasks such as PC data printing, high speed
uploading of scanned data to PC, upload/download of the fax data to send or receive and monitoring the system control signal and overall system from PC are all processed through this part.
PPD( 7: 0)
DATA
BUSY
nSTROBE
nACK
<Compatibility Hardware Handshaking Timing>
3-23
Circuit Description
1
2
3
4
5
6
nSTROBE
BUSY
PPD( 7: 0)
BYTE0
nAUTOFD
DATA BYTE
BYTE1
COMMAND BYTE
<ECP Hardware Handshaking Timing (forward) >
1. The host places data on the data lines and indicates a data cycle by setting nAUTOFD
2. Host asserts nSTROBE low to indicate valid data
3. Peripheral acknowledhes host by setting BUSY high
4. Host sets nSTROBE high. This is the edge that should be used to clock the data into the Peripheral
5. Peripheral sets BUSY low to indicate that it is ready for the next byte
6. The cycle repeats, but this time it is a command cycle because nAUTOFD is low
1 2
3
4
5 6
7
8
nACK
nAUTOFD
PPD( 7: 0)
BUSY
BYTE0
DATA BYTE
BYTE1
COMMAND BYTE
nINI T
PE
<ECP Hardware Handshaking Timing (forward)
1. The host request a reverse channel transfer by setting nINIT low
2. The peripheral signals that it is OK to proceed by setting PE low
3. The peripheral places data on the data lines and indicates a data cycle by setting BUSY high
4. Peripheral asserts nACK low to indicate valid data
5. Host acknow ledges by setting nAUTOFD high
6. Peipheral sets nACK high. This is the edge that should be used to clock the data into the host
7. Host sets nAUTOFD low to indicate that it is ready for the next byte
8. The cycle repeats, but this time it is a command cycle because BUSY is low
3-24
Circuit Description
3-4-2 USB INTERFACE
CS
RD
VVR
A0/ALE
D[7:0]/AD[7:0]
INTR
MODE[1:0]
RESET
Vcc
GND
Microcontroller Interface
Endpoint/Contol FIFOs
48 MHz
Status
Control
RX
TX
Oscillator
Clock
XIN
XOUT
CLKOUT
Generator
SIE
Media Access Controller[MAC]
Clock
Recovery
Physical Layer interface[PHY]
USB Event
Detect
V3.3
Trans ceiver
D+
D-
VReg
AGND
Upstream Port
3-4-2-1 Features
• Full-Speed USB Node Device
• USB transceiver
• 3.3V signal voltage regulator
• 48 MHz oscillator circuit
• Programmable clock generator
• Serial Interface Engine consisting of Physical Layer In-terface (PHY) and Media
• Access Controller (MAC), USB Specification 1.0 compliant
• Control/Status Register File
• USB Function Controller with seven FIFO-based End-points :
• One bidirectional Control Endpoint 0 (8bytes)
- Three Transmit Endpoints (2*32 and 1*64 bytes)
• Three Receive Endpoints (2*32 and 1*64 bytes)
• 8-bit parallel interface with two selectable modes :
- non-multoplexed
• multiplexed (Intel compatible)
• DMA support for parallel interface
• MICROWIRE/PLUS Interface
• 28-pin SO package
3-25
Circuit Description
CS
DATA_IN
0x00
A0
DATA_IN
VVR
RD
DATA_OUT
DATA_OUT
D[7:0]
ADDRESS
ADDR
0x3F
REGISTERFILE
<Non-Multiplexed Mode Interface Block Diagram>
cs
A0
RD
VVR
D[7:0]
input
out
vvrte Address
Read Data
<Non-Multiplexed Mode Basic Timing Diagram>
3-26
out
Burst Read Data
Circuit Description
3-5 Engine Controller
3-5-1. Fuser Control / Thermistor Circuit
This circuit controls the heat lamp temperature to fix the transferred toner on the paper. It is comprised of the
thermistor that has the negative resistance against the temperature and LM393 (voltage comparator) and
transistor for switching.
The thermistor has the resistance value reverse proportional to the heat lamp surface temperature. The voltage value is read by #60 pin(AVIN2) of CPU refering to the parallel combined resistance with the resistor(R43) connected parallel to it and the voltage distribution of R29. The voltage read activates (inactivates)
‘fuser’ signal to high (or low) referring to the set temperature and when the ‘fuseron’ signal turns down(high)
to low(high) by Q3 switching, the S21ME4 inside SMPS (PC3) turns on(off) and this eventually turns two-way
thyristor(SY1) on(off) to allow(shut) AC voltage to the heat lamp.
LM393 is a H/W designed to protect the system when the software heat lamp control does not run normal.
When the thermistor temperature goes up to 210°C, #1 pin’s level (LM393) will turn low to turn the ‘fuseron’
signal to high. (forcefully shuts off Q3)In other words LM393 shuts off the heat lamp forcefully.
3-5-2. Paper Sensing Circuit
1) Cover Open Sensing
Cover Open Sensor is located on the right rear side of the printer. In case the right cover is open, it
shuts +5V (LSU laser unit) and +24V(main motor, polygon motor of fixer LSU and HVPS) that are
supplied to each unit. It detects the cover opening through CPU. In this case, the red LED of the
OP Panel LED will turn on.
2) Paper Empty Sensing
The paper empty sensor (photo interruptor), located inside bottom of the bin cassette detects paper
with the actuator connected to it and informs the CPU of whether there is paper. When there is no
paper in the cassette, the red LED of the OP panel LED will turn on to tell the user to fill the cassette
with papers.
3) Paper Feeding When the paper is fed into the set and passes through the actuator of the feed sensor
unit, transistor inside the photo interrupter will turn on, ‘nFEED’ signal will turn low and inform CPU that
the paper is currently fed into the system. CPU detects this signal and sprays video data after certain
time (related to paper adjustment). If the paper does not hit the feed sensor within certain time, CPU
detects this and informs as “Paper Jam0” (red LED on the OP panel will turn on).
4) Paper Exit Sensing
The system detects the paper going out of the set with the exit sensor assembled to the actuator
attached to the frame. If CPU does not turn back high a while after the paper hits the exit sensor, CPU
detects this and inform as “Paper Jam2” (red LEDs on the OP panel will turn on).
3-27
Circuit Description
3-5-3. LSU Circuit
1) Polygon Motor Unit (actuated by +24V)
The polygon motor inside LSU rotates by the ‘PMOTOR’ signal. When it reaches the motor constant
velocity section through the initial transient (transient response) section, it sends the ‘nLREADY’ signal
to the CPU.
The ‘clock’ pin is the pin that receives clock of the required frequency when LSU uses external CLK as
the motor rotational frequency. Currently the external clock circuit is located in the HVPS and 1686Hz
= 6.9083MHz (crystal frequency)÷212(74HC4060N IC), is used as the rotational frequency of the
polygon motor.
2) Laser Unit (actuated by +5V)
After laser is turned on by ‘nLD_ON’ signal, it is reflected by 6 mirrors (polygon mirror) attached to
the polygon motor and performs scan in horizontal way.When the laser beam hits the corner of the
polygon mirror, it generates ‘nHSYNC’ signal (pulse) and the CPU forms the left margin of the image
using this signal (horizontal synchronous signal).
3-5-4. Fan/Solenoid Actuation Circuit
The fan actuation circuit its power using NPN TR. When it receives ‘FAN’ signal from the CPU. The TR will turn
on to make the voltage supplied to the fan to 24V in order to actuate the fan.
The solenoid is actuated in the same way. When it receives control signal from the CPU, the solenoid for
paper feeding is actuated by switching circuit.
D29(1N4003) diode is applied to the both ends of the output terminal to protect Q22(KSC1008-Y) from
noise pulse induced while the solenoid is de-energized.
3-5-5. PTL Actuation Circuit
PTL actuation circuit switches its power using NPN TR.
3-5-6. Motor Actuation Circuit
Motor actuation circuit is determined while selecting the initial driver IC (provided by the vendor). This system uses TEA3718(U57, U58), A2918(U59)’s motor driver IC. However, the sensing resistance (R273, R274,
R292, R293) and reference resistance (R284, R289, R294, R295) can vary depending on the motor actuation current value.
It receives motor enable signal (2 phase) from CPU and generates bipolar pulse (constant-current) and
sends its output to stepping motor input.
3-28
Circuit Description
3-5-7. High Voltage Power Supply
3-5-7-1. Summary
It is the high voltage power supply that has DC+24V/DC+5V (used for the image forming device in OA digital picture developing method) as the rated inputs. It supplies electrifying voltage (MHV), supply voltage
(SUPPLY), developing voltage (DEV), blade voltage(BLADE) and transferring voltage (THV).
Each high voltage supply shows the voltage required in each digital picture process.
3-5-7-2. Digital Picture Process
Digital picture developing method is widely used by copy machine, laser beam printer and fax paper.
The process is comprised of electrification, exposure, develop, transfer and fixing.
LSU
MHV
BLADE
SUPPLY
DEV
SUPPLY ROLLER
DEVELOPER ROLLER
HEAT ROLLER
DIRECTION OF PAPER
ELECTRIFICATION
ROLLER
THV
PRESSURE ROLLER
TRANSFER ROLLER
First, in the electrification process, retain constant charge at approx. -900V for the electric potential on the
OPC surface by electrifying OPC drum at approx. -1.4KV through the electrification roller.
The electrified surface of OPC is exposed responding to the video data by the LSU that received print command due to rotation. The unexposed non-video section will retain the original electric potential of -900V, but
the electric potential of the image area exposed by LSU will be approx. -180V that it will form the electrostatic latent image. The surface of the photo-conductive drum where the electrostatic latent image is
formed reaches the developer as the drum rotates. Then the electrostatic latent image formed on the OPC
drum is developed by the toner supplied to the developing roller by supplying roller and it is transformed into
visible image. It is the process to change the afterimage on the OPC drum surface formed by LSU into visible image by the toner particles.
While the supply roller energized with -450V by HVPS and the developer roller energized with -300V
rotate in the same direction, it keeps the toner particles between two rollers supplied to OPC drum in negative state by the friction between two rollers.
The toner supplied to the developer roller is biased to bias electric potential by the developer roller and
transferred to the developing area. After (-) toner is attached to the developer roller, it will move to the exposed
high electric potential surface (-180V) rather than to the unexposed low electric potential surface (-900V) of
the developer roller and OPC drum. Eventually the toner will not settle in the low electric potential surface to
form the visible image.
Later, the OPC drum continues to rotate and reaches to transfer location in order to accomplish the transfer
process.
This process transfers the (-)toner on the transfer roller to the printing paper by the transfer roller. The ()toner attached to the OPC drum will be energized to hundreds to thousands of the (+)transfer voltage by
HVPS. The (+)electrostatic force of the transfer roller generated has higher adhesiveness than the (-)toner
OPC drum and thus it moves to the surface of the paper passing through the transfer roller.
The toner transferred to the paper with weak electrostatic force is fixed to the paper by the pressure and heat
of the fixer composed of pressure roller and heat roller.
The toner attached to the paper is melted by applying the heat (approx. 180°C) from the heat roller and the
pressure (approx. 4kg) from the pressure roller. After the fixing process, the paper is sent out of the set to
finish the printing process.
3-29
Circuit Description
3-5-7-3. Organization of the Device
HVPS is comprised of electrification output unit, bias output unit and transfer output unit.
1) Input Unit
2) Electrification Output (Enable) Unit: MHV (Main High Voltage)
3) Bias Output (Enable) Unit: DEV (Development Voltage)/Supply(Supply Voltage)/BLADE(Blade Voltage)
4) Transfer ‘+’ Output (Enable) Unit: THV(+)(Transfer High Voltage(+))
5) Transfer ‘-’ Output (Enable) Unit: THV(-)(Transfer High Voltage(-))
6) Switching Unit
7) Feedback Unit
8) Regulation Unit
9) Output Unit
SWITCHING
CONTROL UNIT
TRANS
REGULATION
CIRCUIT
OUTPUT
CIRCUIT
MHV
MHV-PWM
<Electrification Unit Block-Diagram>
THVPWM
PWM
CONTROL UNIT
SWITCHING
CONTROL UNIT
REGULATION
CIRCUIT
TRANS
FE E DBACK
THVEA
SWITCHING
CONTROL UNIT
TRANS
REGULATION
CIRCUIT
THVREAD
THV
ENVIRONMENT
RECOGNITION
CIRCUIT
FEED BACK
<Transfer Output Unit Block Diagram>
3-30
THV
Circuit Description
MHV-PWM
PWM
CONTROL UNIT
SWITCHING
CONTROL UNIT
TRANS
MHV
REGULATION
CIRCUIT
OPC
FEEDBACK
<MHV Output unit Block Diagram>
BIAS-PWM
BLADE
PWM
CONTROL UNIT
SWITCHING
CONTROL UNIT
TRANS
REGULATION
CIRCUIT
SUPPLY
FEEDBACK
DEV
<BIAS Output Unit Block Diagram>
3-31
Circuit Description
3-5-7-4 MHV (Electrification Output Enable)
Electrification Output Enable is the electrification output control signal 'PWM-LOW ACTIVE'.
When MHV-PWM LOW signal is received, Q401 turns on and the steady voltage will be accepted to the noninverting terminal of OP-AMP 324. As the voltage higher than the inverting reference voltage of OP-AMP,
which is set to R405 and R406, OP-AMP output turns high. This output sends IB to the TRANS auxiliary
wire through current-restricting resistance Q402 via R408 and C403 and Q402 turns on. When the current
is accepted to Q402, Ic increases to the current proportional to time through the T401 primary coil, and when
it reaches the Hfe limit of Q402, it will not retain the "on" state, but will turn to "off". As Q402 turns 'off',
TRANS N1 will have counter-electromotive force, discharge energy to the secondary unit, sends current to
the load and outputs MHV voltage through the high voltage output enable, which is comprised of Regulation– circuit.
T401
24VS
MHV OUTPUT
C404
3K/471
18V
C406
3K/471
D402
4KV
U103 7407
MHV-PWM
Q402
D526
R405 220K
Q401 A708
24VS
R416
15M
R412 2.2K
R413
12M
OPC
R403 130K
_
KA324
C403
333
C407
104
R411 2K
R417
15M
R409
390
ZD401
150V
R404
27K
R402
82K
R408
47K
+
R406
2.2K
3-5-7-5 BIAS (supply/dev/blade output unit)
BIAS (Electrification Output Enable)Electrification Output Enable is the electrification output control signal
‘PWM-LOW ACTIVE’.When BIAS-PWM LOW signal is received, Q501 turns on and the steady voltage will
be accepted to the non-inverting terminal of OP-AMP 324. As the voltage higher than the inverting reference
voltage of OP-AMP, which is set to R506 and R507, OP-AMP output turns high. This output sends IB to
the TRANS auxiliary wire through current-restricting resistance Q502 via R509 and C504 and Q502 turns
on. When the current is accepted to Q502, Ic increases to the current proportional to time through the T201
primary coil, and when it reaches the Hfe limit of Q502, it will not retain the “on” state, but will turn to “off”.
As Q502 turns ‘off’, TRANS N1 will have counter-electromotive force, discharge energy to the secondary
unit, sends current to the load and outputs DEV voltage through the high voltage output enable, which is
comprised of Regulation-circuit.
24VS
T201
KAB-007
D502
4KV
R514
MGR1/2W 50K
7
BLADE
1
5V
R520
26K
BIAS-PWM
CON03-#24
R501
100
2
R508
47K
5
_
U1
R502
2K
6
C501
R504
56.6KF 104
C502
222
5
Q502
D526-Y
2
U103-A R519
7407
2.2K
R503
100KF
3-32
C503
104
R506
86.6KF
Q501
A708-Y
R507
12KF
+
U101-B
KA324
7
6
C505
2KV 680
C506
3KV 471
ZD501
100V
SUPPLY
ZD501
100V
4
R509
47K
R515
MGR1/2W 50K
R510
430
C504
333
R511
1W 3
R512
MGR1/2W 12MF
DEV
R516
MGR1/2W 50K
Circuit Description
3-5-7-6. THV(THV(+)/THV(-) Output Unit)
Transfer(+) output unit is the transfer output control signal 'PWM-LOW ACTIVE'.
When THV-PWM LOW signal is received, Q203 turns on and the steady voltage will be accepted to the noninverting terminal of OP-AMP 324. As the voltage is higher than the inverting reference voltage of OP-AMP,
OP-AMP output turns high.
The 24V power adjusts the electric potential to ZD201 and ZD202, sends IB to TRANS auxiliary wire
through current-restricting resistance R215 via R212 and C204, and eventually Q204 will turn on. When
the current is accepted to Q402, Ic increases to the current proportional to time through the T201 primary coil,
and when it reaches the Hfe limit of Q204, it will not retain the "on" state, but will turn to "off". As Q402 turns
'off', TRANS N1 will have counter-electromotive force, discharge energy to the secondary coil, sends current to the load and outputs THV voltage through the high voltage output enable, which is comprised of
Regulation– circuit. The output voltage is determined by the DUTY width. Q203 switches with PWM DUTY
cycle to fluctuate the output by fluctuating the OP-AMP non-inverting end VREF electric potential, and the
maximum is output at 0% and the minimum, at 100%.Transfer(-) output unit is THV-EA 'L' enable.
When THV-EA is 'L', Q302 turns on and the VCE electric potential of Q302 will be formed and sends IB to
TRANS auxiliary wire through R311, C305 and VR302 via current-restricting resistance R314, and eventually Q303 will turn on. When the current is accepted to Q303, Q303's Ic increases to the current proportional
to time through the T301 primary coil, and when it reaches the Hfe limit of Q303, it will not retain the "on" state,
but will turn to "off". As Q303 turns 'off', TRANS N1 will have counter-electromotive force, discharge
energy to the secondary coil, send current to load and output THV(-) voltage through the high voltage output
enable, which is comprised of Regulation– circuit.
5V
18V
24VS
R201
10K
#7
TEV-PWM
1
U2
2
3
T201
KAB-007
U2
1
R206
100
R205
1.8K
D201
1N4148
5 +
24VS
VR201
50K
7
U1
R209
100KF
R207
2K
6
C201
103
C202
121
R210
845KF
D202
1N4148
R211
1MF
5
R213
2.2K
_
Q204
D526
11 KA324
C203
472
D203
1N4148
ZD201 ZD202
5.65V 705V
C204
333Z
R214
2.2K
D207
6KV
C207
3KV470pF
4
R215
390
D206
6KV
C209
6KV
D205
6KV
R218
MGR1/2W100KF
R216
SBR306
R212
680K
#19
D204
6KV
6
2
+ C101
35V47UF
#17
C208
6KV
C205
2KV68pF
R208
30K
Q203
A708Y
C206
6KV470pF
7
R217
SBR207
5V
18V
D301
1N4148
5V
R312
1W56
R309
202K
#5
TEV-EA
5
6
7
U2
7407
R307
33K
24VS
KAB-006
T301
Q301
A708Y
1
C306
2KV68pF
18V
D-GND
5
C4
103
#24
TEV-READ
8
R310
2.2K
R308
33K
+ 10
U1
_
KA324
R301
470K
9
R302
33K
R303
100KF
C302
102
R304
389KF
D302
1N4148
C303
103
R306
26.1KF
C307
3KW470pF
Q303
D526
D304
4KV
6
R313
1W56
D303
4KV
C308
3KV470pF
R315
SBR306
7
2
Q302
A708Y
VR302
2K
R311
100KF
C305
333Z
4
R314
1.7K
R305
10KF
VR301
5K
C304
500V103Z
C301
222
3-33
Circuit Description
3-5-7-7. Environment Recognition
THV voltage recognizes changes in transfer roller environment and allows the voltage suitable for the environment in order to realize optimum image output. The analog input is converted to digital output by the
comparator that recognizes the environmental changes of the transfer roller. It is to allow the right transfer
voltage to perform appropriate environmental response considering the environment and the type of paper
depending on this digital output by the programs that can be input to the engine controller ROM.
This environment recognition setting is organized as follows: First, set the THV(+) standard voltage.
Allow 200MΩ load to transfer output, enable output and set the standard voltage 800V using VR201.
Then set 56 (CPU's recognition index value) as the standard using VR302.
This standard value with CPU makes sure that the current feedback is 4µA when output voltage is 800V and
load is 200MΩ.
If the load shows different resistance value when 800V is output, the current feedback will also be different
and thus the index value will also be different. according to the index value read by CPU, the transfer voltage
output will differ according to the preset transfer table.
The changes in transfer output required by each load is controlled by PWM-DUTY.
3-34
Circuit Description
3-6 OPE PBA
3-6-1 SUMMARY
OPE Board is separated functionally from the main board and operated by the micom(HT48R50) in the board.
OPE and the main use UART (universal asynchronous receiver/transmitter) channel to
exchange information. OPE reset can be controlled by the main. OPE micom controls key-scanning and LCD
and LED display. If there occurs an event in OPE (such as key touch), it sends specific codes to the main to
respond to the situation and the main analyzes these codes and operates the system. For example, it the
main is to display messages in OPE, the main transmits data through UART line to OPE according to the
designated format and OPE displays this on LCD, LED. OPE’s sensing is also transmitted to the main through
UART line and then the main drives necessary operation.
OPE PBA consists of U1(MICOM, HT48R50),LCD, key matrix, LED indicators. Refer to OPE Schematic
Diagram and Wiring Diagram sections of this manual.
• Signals from the key matrix are delivered to U1 input pin group (D1~D6)
• U1 pin 48 (TX DATA) is the UART code sent to MAIN PBA.
• Display from the controller is received at U1 pin 5(RX DATA).
• LCD drive signals are sent from U1 P2-x pin group, P3-4~P3-6 pins.
• Machine status LED drive signals are sent from U1 LED0~LED7.
RESONATOR
7.37 MHz
11
UART
Connector
Reset
MICOM
HT48R50
LCD
16 2line
7
X
Y
8
Key Matrix
LEDs
<OPE BLOCK DIAGRAM>
3-35
Circuit Description
3-7 LIU PBA
3-7-1. SUMMARY
LIU WIRE CONNECTS Main B’D’s MODEM AND LINE PARTS, AND IMPEDANCE MATCHING (AC, DC),
RING DETECTION PART and LINE SEIZURE (DIALER).
3-7-2. DC MATCHING PART
Normal movement range of LIU is 12mA ~ 9mA.
Adapting CTR21 standard, the regulation limits to 60mA CURRENT flow through the terminal.
Therefore, select (*:for EU PIT) Option to connect necessary items then the current through LIU will not
exceed 60mA.
• CTR21 Standard(Europe) : 12mA~60mA
• OTHER Standard (U.S.) : 12mA~90mA
DC has a character to pass through the LINE. And with Q1 (VN2410) GATE section’s LINE INPUT corrent
and Q1 Source connection to R20, can be decided as follows :
• -VDCR = VL1 + ILINE X R20
(VDCR : Tip-Ring CD Voltage, ILINE :
Current flow)VL1:Line Input Voltage, VL1=VBD1+VCE(Q2)+VDS(Q1)
3-7-3. AC MATCHING PART
Basic LIU’s AC IMPEDANCE is 600 and uses R47. 48. C36 to possibly control combined IMPEDANCE.
• U.S. Usage : A terminal IMPEDANCE Æ 600W(±30%)
• CTR21 : A Terminal IMPEDANCE Æ 270+750W//150nF
3-7-4. DIALER PART
*MF DIAL
DTMF Dialing is controlled by MODEM and should be selected by appropriate LEVEL and On-off Time output
based on each countries’ own National specification.
• Freq. Tolerance : ±1.5%
High Group : 1209, 1336, 1477, 1633Hz
Low Group : 697, 770, 852, 941 Hz
U.S. Usage
CTR21
High Freq Level
-9.0+2.0/-2.5
-7.0 +1.0/-2.0
Low Freq Level
-9.0+1.0/-2.0
-11.0+2.5/-2.0
*DP DIAL
Controls from MAIN through / DP-Terminal.
for U.S.Usage, set time to DF signal of 40:60 M/B. DP signal is made of U6 (pcb817). The DC current which
flows thru Q2 Base is regulated by On/Off switch and turns to DP dial signal with a COUPLER.
• CTR 21 does not have telephone capability but has the number 3 and 4 Line Connection. No DP condition
but possibility to get approval only on DTMF Dial based terminal.
3-7-5. RING DETECTION PART
RING SIGNALS from the LINE section (TIP, RING)are further passed through C5, R3, ZD1, and ZD2 and
ends up at U9, (PC 814). U9 then detects above RING SIGNAL and passes the output to MAIN B’D. The wilre
diagram’s C5 is RINGER CAPACITOR and it normally uses 1UF/250V.
A R3 limits AC current and controls upper and lower REN meter.
3-36
Circuit Description
3-8 SMPS (Switching Mode Power Supply) Unit.
3-8-1 SMPS Specifications
The SMPS (Switching Mode Power Supply) Unit used here is a PWM (Pulse Width Modulation) type power
supply unit that supplies DC+5V to controller and control panel, and DC+5V, DC+24V and DC+12V to the
engine. It also supplies AC power to fixer heat lamp.
No.
Output Channel
Ch.1
Ch.2
Ch.3
1
Channel Name
+5.1V
+24.0V
+12.0V
2
Rated Output Voltage
+5.1V
+24.0V
+12.0V
3
Rate Output Current
2A
2.5A
0.8A
4
Maximum Load Current
and Load Pattern
2.5A Continued
3.0A Continued
0.8A Continued
5
Load Change Range
0.5~2.0A
0.1~0.3A
0.1~0.8A
6
Rate output voltage
(For rated I/O)
+5.1V±5%
(+4.84~+5.35V)
+24.0V±10%
(+21.60~+26.40V)
+12V±5%
(+11.40~+12.60V)
7
1) Total Output Voltage
Deviation
(Input, Load, Temp., Aging)
2) Dynamic Input Change
3) Dynamic Load Change
Including All
+5.1V±5%
(+4.84~+5.35V)
Including Set Error
Including All
+24.0V±10%
(+21.60~+26.40V)
Including Set Error
Including All
+12V±5%
(+11.40~+12.60V)
Including Set Error
8
Refer to ripple & noise 27
150mVp-p or less
500mVp-p or less
200mVp-p or less
9
Refer to load short and
overload protection 23
Refer to load short and
overload protection 23
Must not ignite or
generate smoke
when output shorted
for 5 sec.
Output voltage must
shutdown withing
the range of
3.5A~6.5A
Must not ignite or
generate smoke
when output shorted
for 5 sec.
3-37
Circuit Description
3-8-2 AC Input Stage
AC Input power path is consist of the Fuse (F1) for AC current limit, the Varistor (TNR1) for by-passing high
Voltage Surge, the discharge resistor(R1), the AC Impalse Noise Filtering Circuit (C2, C4, LF1), the Common
Mode Grounding Circuit (C5, C6), the 2’nd noise filter (C7, LF2), and the thermistor (TH1).
Wher power is turned on, TH 1 limits Inlush-Current by it’s high resistanle, and When it’s temperature rise, it’s
resistance become about Zero ohm.
3-8-3 SMC(Switched Mode Control)
The AC input voltage is rectified and filtered by BD1 and C10 to create the DC high voltage applied to the primary winding of T1, Q5 pin #1 is driven by the SMPS device IC2, IC2. auto-starts and chops the DC voltage.
The U502 is PWM SMPS IC and has internally a SMC(switched mode control) IC and a MOSFET output
stage. The SMC IC has a Auto-restart without a Power Supply for the IC and a Thermal Shutdown function
and so on. R4, R5, C11, D1 clamp leading-edge voltage spikes caused by transformer leakage inductance.
The power secondary winding(Pin #5~6)is rectified and filtered by D8, D9, L2, C33, C34 to create the 5V output voltage. The bias winding(Pin #9~8)is rectified and filltered by D2 and C12 to create U502 bias voltage.
The secondary output 5V is regulated through the path of the voltage divide by R34, R35.
3-8-4. Fixed Temperature Control
3-8-4-1. Fixed Lamp Control Circuit
AC Power Live
AC Neutral
L1
R24
Zero crossing circuit
C18
4
Logic Unit
Fuser On
2
SY1
R66
1
6
CON502
R23
PC3
<Fixed Lamp Control Circuit>
3-38
SMPS Unit
DC Power
Circuit Description
3-8-4-2. The Concept of Fixed Lamp Control
For fixed lamp control, the logic unit "fuser on" control signal and SMPS unit DC power must be supplied.
This circuit turns on only when "fuser on" sends the signal and the DC power is supplied.
The following explains how the fixed lamp control circuit works.
logic unit "fuser on" sends trigger current to triac driver PC3 LED, then the infrared ray is detected by PC3
photo detector. Next, YC3 triac is conducted.
The conducted current sends trigger input to triac SY1 gate. At this point, SY1 is conducted and AC power
is supplied to fixed lamp. Lamp is turned on and temperature rises.
As this fixed lamp control circuit uses the AC voltage ("+" and "-" are repeated) as the power supply, it used
two-way triac (SY1), which has advantage over one-way SCR considering the price, size and reliability.
Triac's gate can be triggered by either forward or reverse signal. Once triac is turned on, it will not be controlled by gate signal, but will be continuously on until the current between major terminals decreases below
the holding current. In other words, you cannot turn it off with reverse signal unlike SCR. This property is called current-voltage threshold rise rate (commutation: dv/dt). In AC power control
application, triac has to turn off conduction in each zero crossing or switch it twice in each cycle. This switching operation is called commutation. It is possible to turn off the triac at the end of half cycle by eliminating the
gate signal when the load current (IL) is gained at the level equal to or lower than holding current. When
triac commutes off-line, the direction of the voltage of the both ends of triac will be reversed and increase
up to the maximum value of line voltage (VAC). At this point, the width of rise rate will be determined by dv/
dt and overshoot voltage, by the circuit. When triac commutes off-line, the voltage of both ends of triac will
have the same voltage as the line voltage.
IL
Inductive IL
VT
VAC
G
<Inductive Circuit>
3-39
Disassembly and Reassembly
4. Disassembly and Reassembly
4-1 General Precautions on Disassembly
When you disassemble and reassemble components, you must use extreme caution.
The close proximity of cables to moving parts makes proper routing a must. If components are removed, any
cables disturbed by the procedure must be restored as close as possible to their original positions. Before
removing any component from the machine, note the cable routing that will be affected.
Whenever servicing the machine, you must perform as follows:
1. Check to verify that documents are not stored in memory.
2. Unplug the power cord.
3. Use a flat and clean surface.
4. Replace only with authorized components.
5. Do not force to remove or planten plastic-material components.
6. Make sure all components are in their proper position.
4-2 Rear Cover
1. Remove the six screws securing the Rear Cover.
2. Separate the rear cover from the base frame
and Scanner Ass'y.
4-1
Disassembly and Reassembly
4-3 Scanner Ass'y
1. Before you remove the Scanner Ass'y, you
should remove:
- Rear Cover (see page 4-1)
4. Open the Side Cover assembly first to open the
Front cover. In the other words, close the front
cover first to assembly it.
.
2. Remove the six screws and take out the Shield
Main Upper.Unplug the one connector and CCD
cable.
Side Cover Ass’y
Shield Main Upper
2
1
Front Cover
Notice :
You should connector remove the CCD cable vertically to
avoid the CCD cable pin damage.
3. Remove the three screws, as shown below.
4-2
5. Remove two screws.
Disassembly and Reassembly
6. Pull up the Scanner Ass'y in the direction of
arrow.
9. Remove the three screws securing the Platen
Ass'y.
7. Remove the connector from the Platen Ass'y.
10. Pull the OPE Ass'y and unplug the one connector.
8. Open the ADF Ass’y in the direction of arrow.
Pull the ADF Ass'y upward and remove it.
11. Remove the five screws securing the Platen Ass'y.
4-3
Disassembly and Reassembly
12. Unlatch the Scan Upper Ass'y securing the
glass and remove it.
14. Remove the four screws and Channel Base
Frame.
Channel Base Frame
Notice :
When foreign material enters into the Scan Assy, it may
cause problems in product performance and deteriorate
scan image. Therefore, you should always dismantle or
assemble it at a clean place.
13. Remove the two scews and pull the Dummy
Upper Ass’y.
15. Remove the five screws and Dummy ScanLower.
Dummy Upper Ass’y
Cover Dummy Lower
Cover Scan Lower
4-4
Disassembly and Reassembly
16. Remove the CCD cable.
18. Remove three screws and take out the Motor
Bracket.
17. Pull up the Shaft CCD and take out the Scanner
Module.
19. Remove the OPE Harness from the Platen
PBA. Remove two screws and take out the
Platen PBA.
Platen PBA
Shaft CCD
OPE Harness
Pully
Scanner Module
Belt
4-5
Disassembly and Reassembly
4-4 ADF Ass'y
1. Before you remove the ADF Ass'y, you should
remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page 4-2)
4. Pull the ADF Ass'y upward and remove it.
2. Remove the five screws from the Platen Cover.
Platen Cover Ass’y
Platen Cover Ass’y
3. Open the Cover open and pull the Cover Side L
and Cover Side R and unlatch the Side Cover L
by pushing the part hooked the Platen Cover
using a sharp tool.
Side Cover R
Side Cover L
Cover Open
Platen Cover
Ass’y
4-6
5. Tack out he Open Cover.
Disassembly and Reassembly
6. Take out the Pick-up Ass’y.
Remove the four screws and the ADF Upper.
7. Remove three screws and take out the ADF
Motor ass'y.
Pick-up Ass’y
ADF Upper
4-7
Disassembly and Reassembly
4-5 OPE Ass'y
1. Before you remove the OPE Ass'y, you should
remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page 4-2)
2. Remove ten screws securing the OPE PBA and
the LCD Module from the OPE Cover.
3. Remove the contact rubbers from the unit.
4-8
4. Remove the key pad from the unit.
Disassembly and Reassembly
4-6 Side Cover Ass'y
1. Remove the two screws to release the Stopper(Main Frame side) securing the Side Cover
to the Main Frame.
* MP-Tray
1. Pull the both side of the
part to dissemble it.
1
1
2. Completely open the Side Cover Ass’y, and
after pull the
part to the arrow direction (to
the top), pull the
part to the arrow direction
(inner side).
2
2. As the
part, make the Tray-Case and the
Tray-Link in rectangular position to dissemble
the Tray-Case from the Tray Link. The Tray Link
locates at an angle of 45˚ from the Side Cover
Ass’y and then remove the Tray Link.
MP Tray
2
3
1
1
Tray Link
Tray-Case
4-9
Disassembly and Reassembly
* Duplex Ass’y
* Transfer Roller Ass’y
1. Unite the
part and home to the projection
part of the Side Cover assembly, and widen
them from each other to dissemble the Side
Cover Ass’y.
1. Take out the Transfer Roller, as shown below.
Deplex Ass’y
4-10
Disassembly and Reassembly
4-7 Fuser Ass'y
1. Before you remove the Fuser Ass'y, you should
be power off and remove:
- Side Cover Ass'y (see page 4-9)
2. Remove the one screw and take out the Cover
Sheet Connector.
6. Remove the two screws and take out the Halogen Lamp.
Halogen Lamp
5. Remove the four screws and take out the Thermostat.
Thermostat
3. Unplug the one connector.
7. After remove the two screw and open the Lower
Ass’y froward tack out the Heat Roller Ass’y
from Upper Fuser Ass’y.
4. Remove the three screws and take out the Fuser
Ass'y.
Heat Roller
4-11
Disassembly and Reassembly
4-8 Exit Ass'y
1. Before you remove Exit Ass'y, you should
remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page 4-2)
3. Pull the exit ass’y and remove it.
2. Remove four screws, and then untile the harness
from the Exit Upper. Unplug four connectors and
unlatch the Dummy Base Frame, as shown
below.
4-9 Cover Paper Exit Ass'y
1. Before you remove the Cover Paper Exit Ass'y,
you should remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page4-2)
2. Remove two screws and Cover Paper Exit Ass'y,
as shown below.
Cover Paper Exit Ass’y
4-12
Disassembly and Reassembly
4-10 Drive Ass'y
1. Before you remove the Drive Ass'y, you should
remove:
- Rear Cover (see page 4-1)
- Shield Main Upper (see page 4-2)
3. Remove the one screw and take out the Fan and
Dust Fan.
2. Unplug the two connectors.
(Main Motor:9pin, Duplex Solenoid : 2pin)
Fan
Dust Fan
4. Remove the five screws and take out the Drive
Ass'y.
4-13
Disassembly and Reassembly
4-11 SMPS
1. Before you remove the LSU, you should remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page 4-2)
- Cover Paper Exit Ass’y(see page 4-12)
3. Unplug the all connectors.
2. Remove three screws and take out the Shield
SMPS Upper.
4. Remove the SMPS, as shown below.
SMPS
4-14
Disassembly and Reassembly
4-12 LSU (Laser Scaning Unit)
1. Before you remove the LSU, you should remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page 4-2)
- Cover Paper Exit Ass’y (see page 4-12)
3. Remove the three screws and take out the LSU.
LSU
2. Unplug the two connectors.
4-15
Disassembly and Reassembly
4-13 Cover Exit Rear
1. Before you remove the Cover Exit Rear, you
should remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page 4-2)
- Exit Ass'y (see page 4-12)
- Cover Paper Exit Ass’y(see page 4-12)
- SMPS (see page 4-14)
2. Remove the one screw and take out the Panel
Connect MPF.
4-16
3. Remove the one screw and Cover Exit Rear, as
shown below.
Cover Exit Rear
Disassembly and Reassembly
4-14 Main Frame Ass'y
1. Before you remove the LSU, you should remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page 4-2)
- Side Cover Ass'y (see page 4-9)
- Fuser (see page 4-11)
- Exit Ass'y (see page 4-12)
- Cover Paper Exit Ass’y(see page 4-12)
- SMPS (see page 4-14)
- LSU (see page 4-15)
4. Unplug the all connectors.
2. Remove one screw in the Channel Base Frame
from the bellow section of the Base Frame, and
then remove the rest of the five screws to dissemble the Dummy Base Frame, the Cover
Front and the Cam Jam Remove.
Dummy Base Frame
Cam Jam Remove
5. Remove the seven screws and take out the
Main Frame Ass'y.
Main Frame Ass’y
Front Cover
3. Remove the Locker Deve, and then remove the
one screw and the Cover Motor Bracket.
Cover Motor Bracket
Lock Deve
4-17
Disassembly and Reassembly
4-15 MP Ass'y
1. Before you remove the MP Ass’y, you should
remove:
- Rear Cover (see page 4-1)
- Shield Main Upper (see page 4-2)
- Side Cover Ass'y (see page 4-9)
4. remove the three screws.
2. Unplug the two connectors.
3. Remove the one screw and take out the Dummy
Cover.
5. Release the SMPS fit. Pull the MP Ass'y upward
and remove it.
MP Ass’y
Dummy Cover
4-18
Disassembly and Reassembly
4-16 Feed Ass'y
1. Before you remove the Feed Ass’y, you should
remove:
- Rear Cover (see page 4-1)
- Scanner Ass'y (see page 4-2)
- Side Cover Ass'y (see page 4-9)
- Exit Ass'y (see page 4-12)
- Cover Paper Exit Ass’y(see page 4-12)
- LSU (see page 4-15)
- Main Frame Ass’y (see page 4-17)
3. Pull the Feed Ass'y upward and remove it.
Feed Ass’y
2. Remove the three screws.
Feed Ass’y
4-19
Disassembly and Reassembly
4-17 Pick Up Ass'y
1. Before you remove the Pick Up Ass’y, you should
remove:
- Rear Cover (see page 4-1)
- Shield Main Upper (see page 4-2)
- Drive Ass'y (see page 4-13)
4. Remove the four screws and take out the Pick Up
Ass'y, as shown below.
2. Unplug the three connectors.
Guide Paper Out
Pick-up Ass’y
3. Remove the two screws and take out the Cassette Rail.
Cassette Rail
4-20
Disassembly and Reassembly
4-18 Main PBA
1. Before you remove the Main PBA, you should
remove:
- Rear Cover (see page 4-1)
- Side Cover Ass'y (see page 4-9)
- Cover Paper Exit Ass’y(see page 4-12)
- SMPS (see page 4-14)
3. Remove the five screws and take out the main
PBA from the Shield Main Lower.
Main PBA
2. Remove the two screws and take out the Shield
Main Lower.
Shield Main Lower
4. Remove the one screw and unlatch the LIU PBA
securing the main PBA and remove it.
LIU PBA
(Only SCX-5312F)
Main PBA
4-21
Troubleshooting
5. Troubleshooting
In this chapter, it was mentioned about the functions for maintaining the product, how to find the causes of the
inferiority, and troubleshooting method.
5-1 Preventative Maintenance
The cycle period outlined below is a general guideline for maintenance.
The example list is for an average usage of 50 transmitted and received documents per day.
Environmental conditions and actual use will vary these factors.
The cycle period given below is for reference only.
COMPONENT
REPLACEMENT CYCLE
ADF Rubber
50,000 Pages
ADF Roller
50,000 Pages
Pick-up Roller
50,000 Pages
Transfer Roller
50,000 Pages
Fuser
50,000 Pages
Toner Cartridge
6,000 Pages
Drum Cartridge
15,000 Pages
5-2 Error Messages
ERROR MESSAGE
DESCRIPTION
SOLUTION
[BYPASS JAM]
When the machine detected the non-feeding from
BYPASS Tray.
Open the side Cover and clear the jam.
COMM. ERROR
A problem with the facsimile communications has
occurred.
Try again.
DOCUMENT JAM
Loaded document has Jammed in the feeder
When Document Jam aeeurred at ADF module
Clear the document Jam.
[DOOR OPEN ]
The side cover is not securely latched.
Clear the cover until it clicks in place.
DRUM WARNING
When the machine has encountered the drum
life,14000 print pages.
Use little more change if “REPLACE
DRUM” is marked in LCD window.
[DUPLEX JAM]
OPEN/CLOSE DOOR
When the machine detected the duplex jam in the
middle of machine.
Clear the jam.
GROUP NOT AVAILABLE
You have tried to select a group location where
only a single location number can be used, such
as when adding locations for a multi-dial operation.
Try again, check location for group.
HEATING ERROR
During operation, Temperatare does not go up.
Check thermister contact point & Heating
Lamp.
LINE ERROR
Your unit cannot connect with the remote
machine, or has lost contact because of a problem on the phone line. When the mechine has a
problem in cause of fax data reception step
Try again. If failure persists, wait an
hour or so for the line to clear then try
again.
5-1
Troubleshooting
ERROR MESSAGE
DESCRIPTION
SOLUTION
INVALID
CARTRIDGE
You have used unauthorised cartridge.
You must use a Samsung approved cartridge.
LINE BUSY
The remote FAX didn’t answer
Try again.
LOAD DOCUMENT
You have attempted to set up a sending operation with no document loaded.
Load a document and try again.
MEMORY FULL
The memory has become full.
Either delete unnecessary documents, or
retransmit after more memory becomes
available, or split the transmission into
more than one operation.
NO ANSWER
The remote machine was not answered after all
the redial attempts.
Try again.
Make sure the remote machine is OK.
NO DEVELOPER
CARTRIDGE
When the machine detected the toner cartridge
has not been installed.
Install the Cartridge.
NO. NOT ASSIGNED
The speed dial location you tried to use has no
number assigned to it.
Dial the number manually with the keypad, or assign the number.
[NO PAPER]
ADD PAPER
The recording paper has run out. The printer system stops.
Load the recording paper in the paper
feeder.
[PAPER JAM 0]
OPEN/CLOSE DOOR
Recording paper has jammed in paper feeding
area.
Recording paper is jammed in pick-up unit
Press STOP and clear the jam.
[PAPER JAM 1]
OPEN/CLOSE DOOR
Recording paper has jammed inside the unit.
Recording paper has jammed in paper exit unit.
Clear the jam.
[PAPER JAM 2]
CHECK INSIDE
Paper has jammed in the paper exit area.
[TONER EMPTY]
When the machine has encountered the Toner
Empty.
Replace the Toner Cartridge.
[TONER LOW]
The toner is almost empty.
Take out the toner cartridge and gently
shake it. By doing this, you can temporarily re-establish printing operations.
REPLACE DRUM
When the machine has encountered the out of
from lifr, 15000 print pages.
Replace the Drum Cartridge.
RETRY REDIAL?
The machine is waiting for the programmed interval to automatically redial.
You can press START to immediately
redial, or STOP to cancel the redial
operation.
OPEN HEAT EROR
Thermister does not connected to main board or
contact point is not coupled tightly in power on.
Check thermister contact point, Heating
Camp & Thermostat.
[OVERHEAT]
The printer part has overheated.
Your unit will automatically return to the
standby mode when it cools down to normal operating temperature. If failure persists, call service.
SCANNER LOCKED
Scanner is locked by locker.
Check locker.
Connect the Flat-Cable.
5-2
Troubleshooting
5-3 Tech Mode
5-3-1 How to Enter Service Mode
In service mode (tech) mode, the technician can check the machine and perform various test to isolate the
cause of a malfunction.
To enter the Tech mode, press MENU, #, 1, 9, 3, 4 in sequence, and the LCD briefly displays ‘T’, the
machine has entered service (tech) mode.
While in Tech mode, the machine still performs all normal operations.
To return to normal user mode, press MENU, #, 1, 9, 3, 4 in sequence again, or turn the power off, then on
by unplugging and plugging the power cord.
Options changed while in service mode do not remain changed unless you clear the machine’s memory.
5-3-2 SYSTEM DATA
DIALING MODE
Select the dialing mode according to the user's line status.
• TONE: Electrical type of dial
• PULSE: Mechanical type of dial
SILENCE TIME
In ANS/FAX mode, after a call is picked up by the answering machine, the machine monitors the line. If a
period of silence is detected on the line at any time, the call will be treated as a fax message and the machine
begins receiving.
Silence detection time is selectable between limited (about 12 seconds) and unlimited time.
When '12 sec' is selected, the machine switches to receiving mode as soon as it detects a period of silence.
When 'unlimited'is selected, the machine waits until the answering operation is concluded even though a
period of silence is detected. After the answering operation is concluded, the machine switches to receiving
mode.
SEND FAX LEVEL
You can set the level of the transmission signal. Typically, the Tx level should be under -12 dBm.
Caution: The Send Fax Level is set at the best condition in the shipment from factory. Never change
settings arbitrarily.
ERROR RATE
When the error rate is about to be over the setting value, the Baud rate automatically lowers up to 2400 bps to
make the error rate remain below the setting value.
You can select the rate between 5% and 10%.
MODEM SPEED
You can set the maximum modem speed.
Communication is done with modem speed automatically set at lower speed when communicating with the
modem with lower speed since communication is done on the standard of the side where modem speed is low
for transmission/reception. It is better set 33.6Kbps as default setting.
5-3
Troubleshooting
5-3-3 MEMORY CLEAR
CLEAR ALL MEMORY
The function resets the system as its very first condition as setting in at the factory.
This function is needed to operate to reset the system to the initial value when the product is abnormally operated or malfunction. All the values are returned to the default values, and all the information, which set in by
user, will be erased.
< Method >
1. Select the [MEMORY CLEAR] at the TECH MODE.
2. Push the ENTER button.
3. Select you country.
4. Push the ENTER button then it will be all memory clear. .
NOTICE : Always perform the memory clear after replace the main board. Otherwise, the system may
not operate properly.
5-3-4 MAINTENANCE
CLEAN DRUM
Use this feature to get rid of the toner remained in the development unit, so you can get a clean printout.
Perform this feature if stains or specks appear on the printing materials and print quality falls.
Perform this feature several times until a clean printing material appears. The machine automatically pulls in a
sheet of paper,and prints out.The toner particles on the OPC drum surface is fixed to the paper.
FLASH UPGRADE
It is Firmware Upgrade function and has two methods, Local and Remote.
More information can be found in the firmware upgrade items.
ADJUST SHADING
The function is to control to get the optimum scan quality by the specific character of the CCD(Charge Coupled Device). If the copy image quality is unsatisfied, perform the function to check the condition of the print
out for checking whether or not having CCD trouble.
< Method >
1. Select the [ADJUST SHADING] at the TECH MODE.
2. Push the SET UP button then an image will be scanned.
3. After the scan, CCD SHADING PROFILE will be print out.
4. If the printed image is different to the image, the CCD is defect.
NOTICE : When you test CCD, make sure
that the cover is closed.
5-4
Troubleshooting
ANSWER ON CNG
The function is to control the CNG TONE cognition times for entering receiving mode from the AUTO MODE
or ANS/FAX MODE
CLEAR COUNT
This function erases information of history such as replacement times of Developing part and OPC drum,
total printing pages, scan times, and etc.
• The items are in the below section of the System Data List, printed at TECH MODE.
• PASSWOEED: 1934
• Current Drum Page Count cannot be erased.
It is possible to erase at NEW DRUM function (USER MODE ⇒ MINTENANCE ⇒ NEW DRUM)
FIRMWARE VERSION
ENGINE VERSION
EMULATION VERSION
:
:
:
TOTAL PAGE COUNTS
CRU PRINTS
REPLACED TONER COUNTS
REPLACED DRUM COUNTS
CURRENT DRUM COUNTS
PLATEN SCAN PAGE COUNTS
ADF SCAN PAGE COUNTS
:
:
:
:
:
:
:
1.00
1.00
PCL6 2.32 07-11-2001
PCL5e 1.48 07-19-2001
123
123
1
1
112
23
10
< SYSTEM DATA LIST >
PATTERN TEST
Using this pattern printout, you can check if the printer mechanism is functioning properly.
It is needed in the production progress. Service person doesn't need to use it.
ROM TEST
Use this feature to test the machine'S ROM. The result and the software version appear in the LCD display.
• FLASH VER : 1.00 V
• ENGINE VER :1.00V
DRAM TEST
Use this feature to test the machine's DRAM. The result appears in the LCD display.
If all memory is working normally, the LCD shows << O K >>
SRAM TEST
Use this feature to test the machine's SRAM. The result appears in the LCD display.
If all memory is working normally, the LCD shows << O K >>
MODEM TEST
Use this feature to hear various transmission signals to the telephone line from the modem and to check the
modem. If no transmission signal sound is heard, it means that the modem part of the main board is poor.
5-5
Troubleshooting
SWITCH TEST
Use this feature to test all keys on the operation control panel. The result is displayed on the LCD window
each time you press a key.
NOTIFY TONER LOW
With this feature enabled, when the toner becomes low, the toner low information will be sent to ta specified
contact point, for example, the service company. After you access this menu, select ON, and when the LCD
prompts, enter the name and the number of the contact point, the customer's fax number, the model name,
and the serial number.
PROGRAM DIAL
It is a function setting transmitting conditions to transmit to specific address preliminary.
When user transmit specific address set this function, the conditionsapplied automatically.
5-6
Troubleshooting
5-3-5 REPORT/HELP
MSG. CONFIRM
It shows the result of the last send operation.
PROTOCOL LIST
This list shows the sequence of the CCITT group 3 T.30 protocol during the most recent sending or receiving
operation. Use this list to check for send and receive errors. If a communication error occurs while the
machine is in TECH mode, the protocol list will print automatically.
Facsimile Information Field
data described in hexdecmal code
Sending/Receiving
Name of signal
(Facsimile Control Field)
FIF data described
in ASCII code
PROTOCOL DUMP LIST
S/R FCF
S
S
S
S
S
S
R
R
S
R
R
S
R
S
S
NSF
CSI
DIS
NSF
CSI
DIS
TSI
DCS
FTT
TSI
DCS
CFR
MPS
MCF
DCN
FIF DATA!
NOV-20-2001
ASCII
61005820003380140200001302090018010000
2020202020202020202020202O20202020202020
00000000 01110111 00010111 00100010
61005020003380140200001302090018010000
202020202020202020202022O202020220202020
00000000 01110111 00010111 00100010
2020202020202020202020202O20202020202020
00000000 01100001 00010101 00000000
2020202020202020202020202O20202020202020
00000000 01100001 00010101 00000000
HELP
It shows a brief description on the machine's basic functions and commands.Use it as a quick reference guide
RECEPTION
This journal shows a specific information concerning reception activities, the time and dates of up to 40 of the
most recent receptions.
TRANSMISSION
This journal shows a specific information concerning transmission activities, the time and dates of up to 40 of
the most recent transmissions.
SYSTEM DATA
This list provides a list of the user system data settings and tech mode settings.
PHONEBOOK
It lists all telephone numbers that have been stored in the machine.
SCHEDULE JOB
This list shows a specific information on the documents currently stored for delayed transmission. It provides
the operation number, starting time, type of operation, etc.
ERROR CODE
It shows error history occurred using product.
5-7
Troubleshooting
5-3-6 Firmware Upgrade
It is a new Firmware, and there are two Upgrade methods by local and remote.
5-3-6-1 Local Machine
RCP(Remote Control Panel) mode
This method is for Parallel Port.or USB Port Connect to PC and activate RCP(Remote Control Panel) to
upgrade the Firmware.
< Method >
How to Update Firmware using RCP
1. Connect PC and Printer with Parallel Cable or USB Cable.
2. Execute RCP and select Firmware Update. Current Firmware version and Emulation Version are displayed
on Current version window.
3. Search Firmware file to update with Browse Icon.
4. Click Update icon, firmware file is transmitted to Printer automatically and printer is initialized when it finished.
5. Click Refresh icon and check what is updated.
DOS Command mode
This method is just for Parallel Port. Connect to PC with Parallel cable and enter DOS Command to upgrade
the Firmware.
< Method >
a). The first of all, need the files : down.bat, down_com.bin, fprt.exe, and Rom File: file name for upgrade.Save the files in the
same folder.
b). In the DOS, input as below and push the enter key. Then, it will be automatically upgraded.
c) There are two commands for the conditions of product.
* When the product is in idle condition
down "rom file"
* When the product is in idle condition(TECH MODE → MAINTENANCE → FLASH UPGRADE →LOCAL)
fprt "rom file"
d) Do not turn off the power while upgrading process.
Remote FAX
This is a function that a fax with the latest firmware sends files to a fax in long distance through telephone line.
< Method >
1. Operate a fax with the latest firmware to prepare it being upgrade.
(TECH MODE MAINTENANCE FLASH UPGRADE REMOTE)
2. Input the fax number, which needs to be upgraded.
(Several faxes can be upgrade at the same time. In this case, enter the each fax number.)
3. After push the enter button, send the firmware file by calling to the appointed number.
(Around 10~15 minutes needs to send the file.)
< Caution >
1. sending and receiving fax must be the same model.
2. A sending fax must be set up as ECM mode, and a receiving memory must be set up as 100%.
If not, the function operates abnormally.
5-8
Troubleshooting
5-4 ENGINE TEST MODE
The Engine Tests Mode supplies useful functions to check conducting condition of engine. It tests the conducting condition of each device and displays the result of the test at the LCD. It is classified in 6. items (0~5),
and the functions of items are as bellows.
5-4-1 To enter the Engine Test Mode
Press MENU, #, 1, 9, 3, 1 in sequence, and the LCD briefly displays ‘T’, the machine has entered service
(tech) mode.
5-4-2 Diagnostic
Remark
No .
Sub No .
0
1
Motor Test
1: On,
2: Off
2
PTL T est
1: On,
2: Off
3
F an T es t
1: On,
2: Off
4
F us er Test
1 : On, 2: Off
If its temperature is lower than the Standby
(160 C), the fuser is on, but if it is higher than
the Standby, the fuser is off.
1
LSU Motor Test
1: On,
2: Off
2
LSU Hsy nc Test
1: On,
2: Off
3
LD On Test
1: On,
2: Off
4
LSU Operation
1: On,
2: Off
1
F eed Sensor T es t
Sensor O n : FEED SENSOR ON Display
1
2
Eng ine test
Sensor O ff : FEED SENSOR OFF Display
2
Exit Sensor Test
3
Cov er Sensor T es t
Sensor O n : EXIT SENSOR ON Display
Sensor O ff : EXIT SENSOR OF F Display
Sensor O n : COVER SENSOR ON Display
Sensor O ff : COVER SENSOR OFF Display
4
1’st CAST Empty Test
Sensor O n : 1’s t PAPER Empty Display
Sensor O ff : 1’s t PAPER No Empty Display
5
MP Empty Sen T est
Sensor O n : MP PAPER Empty Dis play
Sensor O ff : MP PAPER No Empty Display
6
BIN FULL Sen TEST
Sensor O n : BIN F ULL SEN ON Display
Sensor O ff : BIN F ULL SEN O FF Display
3
4
5
1
1’st CAST Solenoid Test
1: On,
2: Off
2
MP Solenoid Test
1: On,
2: Off
3
Duplex Solenoid T es t
1: On,
2: Off
1
MHV Test
1: On,
2: Off (-1450v)
2
Dev Bias Test
1: On,
2: Off (-450v)
3
T HV EN/NEG T es t
1: On,
2: Off
4
T HV T es t
1: On,
2: Off (1300v)
5
T HV T rigger T est
1: On,
2: Off
1
All Function Test
F or SMD T est, Pus h up k ey : Next function
All Function : No.0~4
5-4-3 ENGINE PRINT
When the function is on, sentence to explain the condition of engine is printed in the below section of the printing output.
It is needed in the development progress. Service person doesn't need to use it.
5-9
Troubleshooting
5-5 Troubleshooting
5-5-1 Scanner
5-5-1-1 COPY
PROBLEM
White copy
Black copy
Defective image quality
Abnormal noise
5-10
ITEMS TO BE CHECKED.
HOW TO SOLVE
• Check the Scan-Cover open.
• Room light can transit a thin original.
• Check shading profile.
• Remake shading profile in the tech mode.
• Check white/black reference voltage in
Main PBA.
• Replace U16 if it is defective.
- U16-97 = 2.5V - U16-98 = 3.3V
- U16-99 = 1.5V
• Check turning the CCD Lamp on when
operating.
• If the CCD is defective, replace it.
- CN3-19 is 5.8V when white original copying for R, B and 3.5V for G.
• Check the CCD problem in Main PBA.
• Check the CCD harness contact.
• Check shading profile.
• Remake shading profile in the tech mode.
• Check the CCD problem in Main PBA.
• If the CCD is defective, replace it.
- Cn3-19 is 7.3V when idle for R, B, and 5V
for G.
• Check shading profile.
• Remake shading profile in the tech mode.
• Check the gap between original and scanner glass.
• The gap above 0.5mm can cause a
blurred image.
• Check printing quality.
• See “Print” troubleshooting.
• Check the Scanner Motor and any
mechanical disturbance.
• Check the right position of the Scanner
Motor, and check the any mechanical disturbance in the CCD carriaging part.
• Check the Motor Driver in Driver PBA.
• If any driver is defective, replace it.
- U55-1 or U55-15 = 0V to 24V swing signal
when operating.
Troubleshooting
5-5-1-2 PC-Scan
PROBLEM
Scanning Error
Defective image
Quality
Abnormal noise
ITEMS TO BE CHECKED.
HOW TO SOLVE
• Check the printer cable installed.
• Check correct installation, and use standard IEEE1284 cable.
• Check how TWAIN driver is installed.
• Remove any other scanner driver.
• Reboot after reinstallation of the TWAIN
driver.
• Check the printer port(Parallel).
• Check the parallel-port-related items in the
CMOS Setup.
As a printer port, Select ECP among
SPP(Normal), ECP, and EPP
modes(increase print-ing speed)
• Check harness contact.
.
• Check CN14 contact in Main PBA
• Check the IEEE1284 signal level.
• If any signal level is defective, replace
Driver PBA.
- U36-66~74 in Main PBA = 0.8V to 2.4V
TTL signal.
• Otherwise, replace Main PBA.
• Check the USB signal level.
• If USB signal level is defective, replace
Main PBA.
• Check shading profile.
• Remake shading profile in the tech mode.
• Check the gap between original and scanner glass.
• The gap above 0.5mm can cause a
blurred image.
• Check the Scanner Motor and any
mechanical disturbance.
• Check the right position of the Scanner
Motor, and check the any mechanical disturbance in the CCD carriaging part.
• Check the motor driver in Driver PBA.
• If any driver is defective, replace it.
- U55 or U56-1 = 0V to 24V swing signal
when operating.
5-11
Troubleshooting
5-5-2 FAX
5-5-2-1 FAX/TELEPHONE Precautions
PROBLEM
TEL LINE CANNOT BE
ENGAGED
(NO DIAL TONE)
ITEMS TO BE CHECKED.
• When you press “ OHD” key:
a) Check line cord connection.
b) Check MAIN LIU harness, and CN1
(LIU PBA).
c )Check relay operation of LIU PBA :
Is the control signal of CN20-7(main) low?
HOW TO SOLVE
a) insert it correctly into the connection
jack called “line”.
b) Replace defective parts.
c) Replace main PBA IF the control signal
of CN20-7(main) is high.
Replace LIU PBA if high but phone line
cannot be connected.
Cannot MF dial
• Check CN20 (main PBA), MAIN-LIU
harness, and CN1 (LIU PBA)
• Replace defective parts.
MF dial is possible but
not DP dial.
• Check DP control signal of CN20-11 of
MAIN PBA and the circuit around R15. U6
and Q2 of Liu PBA.
• Replace LIU PBA.
Defective fax transmission
• Check CN20 (main PBA), MAIN LIU
harness, and CN1(LIU PBA).
• Is the external phone hooked off?
• Check ‘hook off’ : Refer to ‘TEL LINE
CANNOT BE ENGAGED’ above.
• Check the control signals of CN20-11.
• Check transmission path : Check output of
CN20-3.4 and T2-4(LIU PBA).
• Check reception path : Check output CN11 (LIU PBA) and input of CN20-1
(main PBA).
• Replace defective parts.
• Replace LIU PBA if low.
• Refer to ‘TEL LINE CANNOT BE
ENGAGED’ above.
• Replace main PBA, if the signals of CN811 (MAIN PBA) is low.
• Replace main PBA, if abnormal.
• Replace LIU PBA if CN1-1(LIU PBA) is not
confirmed.
Replace main PBA if CN20-1(MAIN PBA)
is not confirmed.
Defective automatic fax
reception
• Is the ring checked?
Check ring pattern at CN1-9 (LIU PBA).
• Refer to ‘Defective Transmission.’
• Replace LIU PBA if it cannot be checked.
• Refer to ‘Defective Transmission’.
5-12
Troubleshooting
5-5-3 Print Quality
Error Status
Vertical black line and
band
Check
Solution
1. Bad blade of Toner cartridge
2. LSU
1. Change Toner cartridge
2. Replace LSU
1. LSU window contamination
2. Toner cartridge
1. Clean LSU window
2. If not LSU, change Toner cartridge.
1. Seal tape is removed?
2. GND OPC is well grounded?
1. Removing seal tipe
2. Measure the resistance between frame
ground and the ground spring attached
frame. Confirm stable ground. Unless bad
ground, detach cabinet, check where is
bad point
3.Adjust LSU or replace it
4. Normal Dev bias = -350V
5. Shake toner cartridge and print.If a liitke
good, toner is empty
6. Test engine test pattern , replace Main
PBA
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Vertical white line
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
No image
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
3. LSU running well?
4. Biss voltage is normal?
5. Lower toner?
6. Is there video data from Main PBA
Light image
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Check seal tape removing
2. LSU light power normal?
3. Enough toner?
4. High charger voltage?
5. Lower bias voltage
6. Contamination of high voltage contact.
1. Check and remove tape
2. LSU light power check is difficult.
Compare with new one and check.
3. Check toner and developer counter
4~5. Measure all high voltage output.
6. Leakage toner cause bad contact and
increase contact resistance. Clean contaminated area.
7. Transfer volatge and roller.
Dark image
Digital Printer
Digital Printer
1. LSU light power normal?
2. Bias voltage output is high?
3. Video data is always supplied?
1. Check the rated level and replace.
2. Set to power rating.
3. Replace defected board.
5-13
Troubleshooting
Error Status
Background
Check
Solution
1. High voltage output is normal?
2. C/R of Toner cartridge is contaminated?
1. Adjust to the rated status.
2. Replace Toner cartridge.
1. High voltage output.
2. Pre-Transfer Lamp.
3. Bad high voltage contact.
1. Check every high voltage.
2. Check the turn-on PTL, LED crash.
3. Clean the inside machine or replace toner
cartridge.
1. Contamination of transfer roller.
1. Clean the transfer roller with vaccum
cleaner.
2. Clean the area of paper path with cloth or
air cleaner.
3. Remove fuser and replace it.
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Ghost
Digital
Digital Printer
Printer
Digital
Digital Printer
Printer
Digital
Digital Printer
Printer
Stains on back of
paper
2. Stains of paper path.
3. Pressure roller’s contamination.
Poor Fusing
Partial blank image
(not periodic)
5-14
3. The machine was under the low tempera
ture for a long time?
1. Should use recommended paper.
2. Check engine controller board.
If you have not thermometer, measure
the thermistor voltage to CPU, If 2.3V±5%
in printing CPU works well. Then, disassemble fuser and check the thermistor
contact and thermistor.
3. Re-check after putting the machine in the
warm place for certain period.
1. Toner is low?
2. The toner cartridge is out of position?
1. Replace Toner cartridge.
2. Checkand adjust.
1. Use recommended paper?
2. Check fusing temperature.
Troubleshooting
Error Status
Partial blank image
(periodic)
Different image density
(left and right)
Horizonral band
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Check
Solution
1. Develope roller scar or particle.
2. Scar or particle. (94 mm)
3. Transfer roller scar or particle .
(47 mm)
1~2. Replace toner cartridge.
1. Charge roller’s pressure force unbalance
2. Dev. roller and OPC or Dev. roller and
blade’s pressure force unbalance
3. Transfer roller’s pressure force unbalance
of each side
1~2. Change toner cartridge
1. Unstable high voltage contact
1. Clean each contact and check good contact
2. Clean charge roller
3. Replace fuser unit
4. Check Main PBA.
3. Replace transfer roller.
3. Check left and right spring of transfer roller
and the spring pressing the developer
inside the machine
2. Charge roller’s contamination
3. Contamination of heat roller
4. Malfunction of LSU
Abnormal Image Printing and Defective Roller
If abnormal image prints periodically, check the parts shown below
NO
Roller
Abnormal image period
Kind of abnormal image
1
OPC Drum
94.3 mm
White spot. Black spot
2
Charge Roller
37.7 mm
White spot. Black spot
3
Supply Roller
35.8 mm
Horizontal dark band
4
Develope Roller
44.8 mm
Horizontal dark band
5
Transfer Roller
57.8 mm
Black side contamination/transfer fault
6
Heat Roller
82.5 mm
Black spot, White spot
7
Pressure Roller
78.5 mm
Black side contamination
5-15
Troubleshooting
No Image
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
No image?
A on
next page
NO
YES
Self test
pattern prints?
YES
Check connection to
computer or replace
controller
NO
Self testing
is possible ?
NO
Retest after replacing the
connector or controller board
YES
Take out the cartridge
and prepare the tester
for electronic connection
Is the OPC
terminal of machine
is well-connected
to Frame?
NO
Repair or replace the GND
terminal
YES
Does the
video data line to
LSU transit to High/Low
when printing?
NO
Check the path between
Main board
and HVPS. Repair or replace
the defective component
or board
YES
The mirror in LSU might be
misplaced so the light path to the
OPC deviates ->Repair or replace
LSU or remove any defective
matters in the machine
5-16
Troubleshooting
A
Transfer
voltage OK? (on the
transfer roller
shaft)
NO
YES
Are the
connection terminal
and connection
correct?
NO
Repair or replace terminal
YES
Replace HVPS or repair defective component
Developing
(-300V) and supplying
(-450V) voltage
are OK?
NO
Is the connection
terminal OK?
NO
Repair or replace terminal
YES
YES
Replace HVPS or repair
defective component
Does the
counter indicate over
the toner's guaranty
life
YES
Replace the toner cartridge
5-17
NO
Transfer roller might be out of its location
-> Locate the roller into its place
This could occurs when he power of LSU is low or
the density is low due to the obstacles on the window
-> Replace LSU or clean the window
Troubleshooting
All Black
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
All black in
printing area?
NO
YES
Does the
video data line to LSU
transit to High/Low when
printing?
NO
YES
Check the path among video
controller, engine board,
HVPS, LSU for the shortage
or open -> Repair or replace
the boards
Replace LSU
Is charge
voltage supplied
from HVPS?
NO
Repair or replace HVPS
YES
Is the
Hsync/ signal received
in LSU?
NO
Replace LSU
YES
Charge part's contact
is bad -> Repair or
replace toner cartridge
5-18
Troubleshooting
Vertical White Line (Band)
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
White line
missing definitely?
YES
Dirt of dust stuck onto the
window of internal lens of LSU
-> Clean it or replace LSU
Preventive obstacles through
the path between OPC of
developer and LSU prevent the
path -> Remove the obstacles
5-19
NO
Check if the
printout is still has the
same problem even right after
passed through the
transfer roller
NO
YES
Toner material might be stuck to
blade in the developer inside and it
prevents toner supply -> Replace
the developer
Check both if the toner cartridge's
counter is over its guaranty and
amount of the toner material
-> Replace the toner cartridge
The ribs in fuser or toner on the
roller may invoke the image
problem -> Replace the fuser
cover or the defective part
The image is originally black or the
black part is far close to the top
-> Use the pattern which has the
image below bigger than 10mm
from the top
Troubleshooting
Dark Image
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
NO
Dark selected
via RCP?
YES
Change to
Normal and test
NO
Same at Normal?
END
YES
Works cor
with -300V of Bias
voltage?
NO
Repair or replace the defective
component
YES
Works
correctly after
replaced LSU?
NO
Toner over supply due to the
adjustment fault of metering
blade in developer
-> Replace developer
YES
The power of LSU is set
high or internal problem
-> Replace LSU or adjust
volume
5-20
Troubleshooting
Background
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Recommended
paper used?
NO
Print 20 to 30 pages using
the recommended paper
YES
- Adjust voltage or
replace HVPS
- Repair or replace
after
checking the
terminals' contacts
NO
Transfer,
charge and developing
voltage are OK?
YES
Same problem
occurs?
NO
END
NO
Replace the
toner cartridge
YES
Operating/
storage atmosphere is
too high temperature
/humidity?
YES
Solve the problem under
the recommended condition
(10-32 degree Centigrade)
NO
Dirt or
dust around the
charge roller?
YES
Clean the charge roller
or replace step-up device
/terminal after check
Check Terminals or contacts and 'Guide-Deve Spring'
are misplaced
-> Repair or replace transfer roller etc.
Check if the LED of PTL in front of the transfer roller
is on when it presses the top cover switch on purpose
-> If not, replace PTL
NO
Work OK?
YES
Internal blade or
supplying part of the
developer is defective
-> Replace the toner
cartridge
5-21
Troubleshooting
Ghost
Digital
Digital Printer
Printer
Digital
Digital Printer
Printer
Digital
Digital Printer
Printer
Is it regular
interval of 95mm?
NO
YES
Replace PTL
assembly
NO
Is it regular
interval of 45mm?
Is it regular
interval of 58mm?
(as transfer roller
interval)
NO
YES
YES
A specific part of the transfer
roller has ruined or its
resistance value is changed
-> Replace transfer roller
PTL lamp
works OK?
YES
Transfer roller cannot force
regularly due to the gears
eccentricity of transfer roller
-> Replace the defective
component
Check HVPS
contacts and
HVPS's selfoutput
-> If failed,
repair/replace
HVPS
NO
Developing
/supplying voltage
normal? (-300V/
-500V)
Transfer
voltage is set to
standard?
NO
YES
YES
Irregularity of NIP
between rollers in
developer
-> Replace developer
Bias voltage
is OK? (-300V)
NO
- Repair or replace HVPS
- Check and Repair or
replace the terminal
contacts
Adjust the Bias
voltage or replace
HVPS
YES
Operating/storage
temperature is too low or
not recommended
paper used?
NO
There may be a problem in toner
layer control in toner cartridge
-> Replace the developer
YES
Use the machine with
recommended paper and
at condition
5-22
Troubleshooting
Black Spot
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Is it regular
interval of 38mm?
NO
YES
The problem occured
since the obstacles
stuck to charge roller
-> Clean the Charge Roller
and then reprint.
5-23
When taking
out the cartridge,
toner leaks?
YES
Toner leaks and much
toner material dropped
onto the paper ->
Replace the developer
NO
Bad image
removes by
scratching?
YES
Check toner is stuck onto
the P/R or H/R in fuser
-> Clean it or replace
NO
The problem
randomly occurred
due to the toner
fallen -> Clean the
machine
Troubleshooting
Horizontal Band
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Black band?
NO
Black band
is far about 95mm from
white band?
NO
YES
The OPC is damaged under the
direct sunlight for around 5
minutes -> If the same problem
persists in 10 hours, replace
the developer
Problem of internal
contacts in OPC
-> Replace developer
The black
band has regular
interval?
NO
This occurs when no
Hsync/ at LSU
-> Replace LSU
YES
94mm interval?
NO
YES
The OPC is damaged due to
the irregular transfer voltage
of HVPS
-> Repair/replace HVPS
-> If the same problem persists,
replace the developer
Does it appear
at every 83mm at
specific place?
YES
NO
Problems of terminal contact,
transfer voltage supplying,
and transfer roller's due to the
charge roller is ruined (38mm)
-> Repair/replace HVPS,
developer
Heat roller is ruined
-> Replace the roller
5-24
Troubleshooting
Irregular Density
OK after
taking out and
rocking the toner
cartridge?
YES
NO
When gray
pattern printing,
irregular density
persists?
NO
YES
transfer/
charge/developing
voltage drops while
printing?
NO
YES
Defective agitator in
the toner supplying part
of developer
->Replace the developer
Check if the 'guide deve
spring' works OK and
repair/repalce
Check high voltage
output and repair/
replace terminals, HVPS
It is over the guaranty
life of toner cartridge
(Check the counter
and replace it)
PTL lamp
works OK?
NO
Replace lamp
YES
Any obstacles
on the PTL lamp?
YES
Clean the window of PTL
5-25
NO
Bad images
NO
around the no image
area?
YES
Light distortion due to
the mirror ruined or
LSU's diffused reflection
-> Replace LSU
Irregularity of toner
supply from developer
-> Replace developer
Troubleshooting
White Spot
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Is it regular
interval of 95mm?
YES
Obstacles stuck on OPC's
surface
-> Clean the OPC and
machine or replace
developer
NO
Transfer
voltage is normal?
NO
Too high voltage supplied
due to the setting error of
transfer voltage
-> Adjust/replace HVPS
YES
D/R in developing unit has
the defect
-> Replace the developer
When putting in/out the
developer, scratch is made
-> Replace the developer
5-26
Troubleshooting
Trembling at the End When OHP Printing
Recommended
OHP film used?
NO
Use the recommended film
YES
Inserted over
than 10 films into
the MPF?
YES
When multi-page OHP printng,
less than 10 films are
guranteed. (Reduce the
number of films and re-insert
after paper check LED if off)
5-27
NO
When OHP
printing, does the fan
temporarily stops
and revolves?
YES
Other parts are touching the
fan and prevents it from
revolution
-> Check and repair
NO
Use the recommended film
Troubleshooting
Poor Fusing Grade
After printing
NO
completed, any error
related fuser?
YES
Both ends
of thermostat
open?
The machine
placed under the
severe low tempera
ture for a long
time?
YES
NO
NO
While printing,
the voltage of pin 60
of U36 (CPU) on Main
PBA is 2.1V
- 2.6V?
NO
Thermistor's
contact is OK?
NO
YES
YES
Re-assemble
thermistor
Place the machine
at normal
temperature and
re-test
YES
Replace thermostat
and re-test
Open the top
cover. When black
printing, is the fuser NIP
width is 3.03.5mm?
NO
Check if the hardness of
P/R, and spring force is OK?
(hardness: 24 degree,
spring's force: 3 Kg)
YES
Replace the control
component on Main
PBA
Check any contact
problem in thermistor
and repair
The paper used is too
thick or contains too
much cotton in it
-> Re-test with the
recommended paper
5-28
Troubleshooting
5-5-4 Malfunction
Error Status
No power
Check
1. Check power is supplying
2. Check fuse F1 open
Fuser Error
1. Thermostat open
Solution
1. If supplying power differs from machine’s power rating, replace the machine.
2. Replace it.
2. AC wire open
3. Thermistor wire open
4. Main PBA
1. Detach AC connector and measure the resistane
between pin 1 and 2. If it is megohm, thermostat is
open, Replace it.
2. Check bad connector contact or wire is cut.
3. Check thermistor wire and its connection.
4. Replace Main PBA
Cover open
1. When close Side cover, check the lever is
pressed
2. Micro switch’s contact
3. CPU and related circuit
1. Open Side cover and press the lever with pen. If
Controller detects cover close, there is some mechanical trouble in Side cover and lever’s assembly. If not
so there is electrical problem.
Jam 0
Check where Jam 0 happens
1. Paper is not picked up
2. Paper is located in feed sensor
3. Happened when inserting specific papers such
as envelope into the MPF (Multipurpose Paper
Feeder)?
4. Happened when inserting specific papers such
as envelope into the Manual Feeder?
5. Is the Stacker Extender is folded out?
6. Does not the Guide Adjust distort the papers
Jam 1
Paper is stopped in just after of fuser unit.
Jam 2
Check where Jam 2 happens
1. Paper is curled and cannot exit.
2. Paper is curled in the exit cover?.
5-29
1. Check whether solenoid is working or not by using
Engine test mode
2. Check feed sensor malfunction.
3. Re-try inserting a fewer papers.
•fan the papers and align
•take out the loaded papers and insert
them reverse direction
4. Take out the loaded papers and insert them reverse
direction
•inserted papers as recommended for
Manual Feeding?
•When loading, tap the papers until paper detect
sensor senses loading
5. When using long papers, use the Stacker Extender
6. Adjust Guide to fit the paper width
1. It is mostly resulted from double feeding. Check
paper is well stocked in feeder.
2. Check feed actuator position and actuator’s operating. There may be stiff movind or double reflection. If
not so, check the operation of feed sensor by Engine
test mode.
3. Check exit lever operation. Remore jam and check
actuator moving by hand. If actuator is too stiff, paper
is wrapped around the heat roller. Remove obstacles
or replace.
1. Remove paper using pinset or some tool and watch if
separate claws have any troble. Clean around fuser.
2. Check locking works wells. Watch whether the ribs of
exit cover hace any burr or resisitive edge. If they do,
remove obstacles or replace.
Troubleshooting
Error Status
Check
Solution
Jam 2 at
face-down
tray
1. Then paper is not drawn in because of the
stack of papers in the Out tray.
2. Does it curl while coming out?
1. Load recommended quantity of papers
Clutch error
1. Check the spring of solenoid
2. Check the armature assembly/cushion
1. Check whether the spring is expanded or not.
2. Check armature is well installed. It may be unstable
assemble.
3. Remove the Main PBA.
3. Electrical check
High voltage error
1. Check the terminal output voltage
2. Check HVPS
Feeding
obstacles
Does the Plate-knockup prevent the paper
loading?
2. Open the Cover Front and check whether roller or
spring, which are related to paper out, is not out of position. If so, re-locate or replace.
1. Remove the Toner cartridge and open the cover and
press cover open switch lever and measure the voltage
with high voltage probe and sending printing data. If the
voltage is normal, change the toner cartridge.
2. Disassemble the left side cover, and check HV of the solder side of HVPS and change it.
MPF :
Turn the power off and on. Open and close the Side cover
to return to the original state.
Cassette :
Adjust Guide to fit the paper width.
Skew
Is the Guide adjust set to the paper
width?
Fit the paper width using the Guide adjust.
Stacking
1. Took out the Stacker extender to support long
papers?
2. Stacked too many papers more than Stacker
can hold?
1. Use extender as per the paper length.
2. The Face-up stacker normally can hold 100 pages when
using 75g/m2, however, stacking capacity can be lowered
depending on the type of papers.
Engine
Error
Check CBF Harness_CN7.
(Main PBA to LSU)
Refer to troubleshooring “ENGINE ERROR”.
Document
Jam
Document is not picked up(in ADF).
1. Check document is well stocked in ADF.
2. Check whether document was been fastened together
by staple or clip.
3. Load recommended quantity of papers.
Document is stopped after it has fed into the
ADF.
1. Check whether the Reg. sensor is working or not.
2. Check whether the Feed Roller is working or not.
Does it curl while coming out?
1. Check the Open Cover whether there are bosses.
2. Check the ADF ass'y is well assemble.
5-30
Troubleshooting
No Power (LCD NO display LED Off)
Plug in the
power cord?
NO
Check the voltage first and plug
the power cord
YES
The power
NO
voltage supplying is
the same as
rating?
Supply the power as the rating
YES
The fan
revolves when
powered on?
Connections
NO
on board are OK?
NO
YES
YES
LEDs blink
once when
powered on?
NO
Fuse of SMPS
if open?
YES
Repair/replace the
board
5-31
NO
Replace the fuse
YES
YES
Shortage on
the OPE panel
board?
Re-connect firmly
and re-test
NO
The connection
error between
controller board
and panel board
or malfunction
of boards.
-> Replace the
boards
Shortage
between 5V and
GND, or between
24V and
GND?
YES
Remove the shortage
or replace the board
NO
Toner cartridge
is in the set?
NO
YES
Detect failure due to the
board which detects side
cover open or switch error
-> Replace the board or switch
Put in the
cartridge
Troubleshooting
Fuser Error
Measure the resistance
at the both ends of AC
Line with covers open
NO
Less than 10W?
Thermostat is open due to the heat etc.
-> Replace the thermostat
YES
Remove the covers
AC is being supplied?
NO
Re-assemble the top
cover and close it
The voltage of pin #6 of U5
on the Main PBA is about
3.2V?
If not check the
CN4 on the power board.
YES
The voltage
of pin #60 of U36
(CPU) on the Main PBA
is about 2.65V when
printing?
NO
Thermistor, connecting point or engine
board defect -> Repair/replace the
component/board
YES
END
5-32
Troubleshooting
Paper Jam (Mis-Feeding)
Sounds the
solenoid on when starts
print?
NO
The solenoid defected
-> Replace it
YES
Does the
paper move?
The Main PBA board defected
-> Replace boards
NO
The pick-up unit is
assembled wrong
-> Re-assemble or replace
the unit
YES
Does the
paper move more than NO
100mm?
Too many
papers in the
feeder?
YES
Feeder
sensor is assembled
reverse?
YES
NO
The sensor and
Main PBA defected
-> Repair/replace
Reduce the amount
and re-test
YES
Switch them
Paper guides
fit the paper width?
NO
Take out the paper
and re-insert
YES
Paper end curled?
YES
Use the recommended
and quality paper
5-33
NO
Does the
extender pulled out?
YES
<Recommendation>
Use the MPF for the thick
paper such as envelope
and cardstock
NO
Pull out the
extender
Troubleshooting
Paper Jam(Jam 1)
Paper
NO
stopped before
the OPC?
Paper
NO
stopped before
the fuser?
YES
YES
The
actuator of
NO
paper exit sensor
works OK?
Check the actuator exists and its
operation and around the Main PBA
-> Replace
YES
Check the LSU and
if it has the defect
replace it
Is the paper
rolled around the
presseure
roller?
Feeds
NO
multiple pages?
NO
YES
YES
Remove the fuser, remove
the paper and replace the
pressure roller, if necessary
Severe skew
when feeding?
NO
YES
Adjust the paper guides to fit the
paper width
The force of springs pressing the
developer is weak
-> Check guide-DEVE
Check the roller
and ribs of fuser
are in place, and
remove burrs, if
any
-> Remove the
factors of jam
Remove any factors
The paper
came out through
between fuser and
developer?
NO
Check the input path
to the fuser (such as
mis-assembly)
YES
Too thin
or sensitive paper to
static electricity?
NO
Check guide transfer
is grounded Check
the shutter prevents
feeding
YES
Use the recommended
paper
5-34
Troubleshooting
Engine Error
Check
CBF Harness-CN7
(Main B'D to
LSU)
NO
Try again to connector or
Replace connector
YES
Check
Main B'D CN7-9,
P_MOTOR Signal
(
)
NO
Replace Main PBA
YES
Check
Main B'D CN7-8,
LREADY Signal
(
)
NO
Replace LSU
YES
Check
Main B'D CN7-4,
LDON Signal
(
)
NO
Replace Main PBA
YES
Check
Main B'D CN7-1,
HSYNC Signal
(
)
YES
END
5-35
NO
Replace LSU
Troubleshooting
5-5-5 Toner Cartridge and Drum Cartridge Service
It is not guaranteed for the default caused by using other toner and Drum Cartridge cartridge other than the
cartridge supplied by the Samsung Electronic or caused by non-licensed refill production.
Precautions on Safe-keeping of the Drum Cartridge
Excessive exposure to direct light more than a few minutes may cause damage to the cartridge.
Service for the Life of Toner Cartridge
If the printed image is light due to the life of the toner, you can temporarily improve the print quality by redistributing the toner(Shake the toner cartridge), however, you should replace the toner cartridge to solve the
problem thoroughly.
Service for Judgement of Inferior Expendables and the Standard of Guarantee
Please refer to User's Manual or Instructions on Fax/Printer Expendables SVC for the judgement of inferior
expendables and the standard of guarantee besides this service manual.
5-36
Troubleshooting
5-5-5-1 Signs and Measures at Poor toner cartridge
Fault
Light image and
partially blank
image
(The life is ended.)
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Toner Contamination
Signs
• The printed image is
light or unclean and
untidy.
• Some part of the
image is not
printed.
• Periodically a noise
as "tick tick" occurs.
• Toner is fallen on the
papers periodically.
• Contaminated with
toner on prints
partly or over the
whole surface.
5-37
Cause & Check
Solution
1. If the image is light or unclean
and untidy printed image - Shake
the developer and then recheck.
(1)NG: Check the weight of the
developer
(2)OK: Lack of toner, so the life is
nearly closed.
1. All of 1, 2, 3 aboveIf it become better by shaking, replace
with a new developer after 50-100
sheets in the closing state of the life
span.
2. Some part of image is not printed
- Shake the developer and then
recheck.
(1)NG: Check the weight of the
developer and clean the
LSU window with a cotton
swab, then recheck.
(2)OK: Lack of toner, so the life is
nearly closed.
2. In case of 2If it becomes better after cleaning the
LSU window, then the developer is normal.
(Because of foreign substance on the
LSU window, the image has not been
printed partly.)
3. Periodically a noise as "tick tick"
occurs - Measure the cycle and
the weight of the developer.
3. In case of 3If the cycle of noise is about 2 seconds,
the toner inside the developer has been
nearly exhausted.( Purchase and replace
with a new developer after using about
200 sheets at the point of occurrence)
4. White vertical stripes on the
whole screen or partly :
Check the weight of the developer.
4. In case of 3This is a phenomenon caused by lack of
toner, so replace with a new developer.
1. Toner is fallen on the paper periodically.
(1)Check the cycle of the falling of
the toner.
(2)Check the appearance of both
ends of the developer OPC
drum.
1. If both ends of the OPC drum are contaminated with toner:
Check the life of the developer.
2.The center of the printed matter is
contaminated with toner.
(1)Check whether foreign substances or toner are stuck to the
terminal (contact point) of the
developer.
(2)Check whether the state of the
terminal assembly is normal.
2. Check whether it could be recycled.
Troubleshooting
Fault
White Black spot
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
• Light or dark black
dots on the image
occur periodically.
• White spots occur in
the image periodically.
Cause & Check
1. If light or dark periodical black
dots occur, this is because the
developer rollers are contaminated with foreign substance or
paper particles.
(1)37.7mm interval :
Charged roller
(2)94.3mm interval :
OPC cycle
1. In case of 1 above Run OPC Cleaning Mode Print 5-5 times
repeatedly to remove. Especially check
foreign substance on the OPC surface,
then remove them with a clean gauze
moistened with IPA(Isopropyl Alcohol) not
to damage OPC if necessary.
2. If white spots occur in a black
image at intervals of 94, 29mm, or
black spots occur elsewhere, the
OPC drum is damaged or foreign
substance is stuck to the surface.
2. In case of 2
If they are not disappeared by running
OPC Cleaning Mode Print 5-5 times.
: at intervals of 94.3mm Replace the developer.
: at intervals of 37.7mm Remove foreign substance, Clean the
Charged Roller
: Broken image Replace the developer according to
carelessness.
3. If a black and white or graphic
image is partially broken at irregular intervals, the transfer roller's
life has been expired or the transfer voltage is abnormal.
Recycled product
• Poor appearance of
the developer.
• Unclean and rough
printouts.
• Bad background in
the image.
Solution
Caution : Never use usual alcohol.
3. In case of 3 - Exchange the transfer
roller because the life of the transfer roller
in use has been expired. (Check the
transfer voltage and readjust if different.)
1. Poor appearance of the developer.
(1)Check the damage to label and
whether different materials are
used.
(2)Check the appearance of parts
of the developer, such as frame,
hopper.
1. In case of 1 (1)If there is an evidence of disassembling
the developer.
(2)If materials other than normal parts of
the developer are added or substituted.
2. Unclean and rough printouts.
(1)Check whether foreign substance or toner are stuck to the
terminal (contact point) of the
developer.
(2)Check whether the state of the
terminal assembly is normal.
2. In case of 2 - If there are any abnormals
in connection with the situation of 1.
(1)It occurs when the developer is recycled over 2 times.
(2)If toner nearly being expired are collected to use, it is judged as the recycled
developer.
5-38
Troubleshooting
Fault
Ghost & Image
Contamination
Signs
• The printed image is
too light or dark, or
partially contaminated black.
• Totally contaminatedblack.
(Black image
printed out)
5-39
Cause & Check
Solution
1. The printed image is too light or
dark, or partially contaminated
black.
(1)Check whether foreign sub
stance or toner are stuck to the
terminal(point of contact) of
the developer.
(2)Check whether the terminal
assembly is normal.
1. All of 1, 2, 3 above
(1)Remove toner and foreign substances
adhered to the contact point of the
developer.
(2)The contact point of the unit facing that
of the developer also must be cleaned.
(3)If the terminal assembly is unsafe:
• Fully stick the terminal to or reassemble
it after disassembling.
• Disassemble the side plate and push
the terminal to be stuck, then reassemble it.
2. Totally contaminated black.
(Black image printed out)
(1)Check whether foreign sub
stances are stuck to the terminal(point of contact) of the
developer and the state of
assembly.
(Especially check the charged
roller terminal.)
2. In case of 2
It is a phenomenon when the OPC drum
of the developer is not electrically
charged. Clean the terminals of the
charged roller, then recheck it.
Troubleshooting
5-5-6 The cause and solutions of bad environment of the software
5-5-6-1 The printer is not working (1)
• Description : While Power turned on, the printer is not working in the printing mode.
Check and Cause
Solution
1. Check if the PC and the printer is properly connected and
the toner cartridge installed.
1. Replace the printer cable. If the problems not solved even
after the cable replaced, check the amount of the remaining
tone.
2. Printing is nor working in the Windows.
2. Check if the connection between PC and printer port is
proper. If you use windows, check if the printer driver in the
controller is set up. If the printer driver is properly set up,
check in which program the printing is not working. The best
way to find out is to open the memo pad to check the function of printing. If it is not working in a certain program, adjust
the setup the program requires. Sometimes, the printout is
normal within the Windows basic programs, but it's not working in a particular program. In such case, install the new
driver again. If not working in the Windows basic program,
Check the setup of the port of CMOS is on ECP. And check
the address of IRQ 7 and 378
3. Check if the printer cable is directly connected to peripheral
devices
3. If the scanner needs to be connected to the printer, first the
remove the scanner from the PC to see if the printer is properly working alone.
5-5-6-2 The printer is not working (2)
• Description : After receiving the printing order, no response at all or the low speed of printing occurs
due to wrong setup of the environment rather than malfunction of the printer itself.
Check and Cause
Solution
1. Secure more space of the hard disk.
1. Not working with the message 'insufficient printer memory'
means hard disk space problem rather than the RAM problem. In this case, provide more space for the hard disk.
Secure more space using the disk utilities program.
2. Printing error occurs even if there is enough space in the
hard disk.
2. The connection of the cable and printer port is not proper.
Check if the connection is properly done and if the parallel
port in CMOS is rightly set up.
3. Check the parallel-port-related items in the CMOS Setup.
3. As a printer port, Select ECP or SPP among SPP(Normal),
ECP, and EPP modes(increase printing speed) SPP normal
mode support 8-bit data transfer, while ECP Mode transfer
the 12-bit data.
4. Reboot the system to print.
4. If the regular font is not printing, the cable or the printer
driver may be defective.
Turn the PC and printer off, and reboot the system to print
again. If not solved, double-click the printer in my computer
If the regular fonts are not printed this time again. the cable
must be defective so replace the cable with new one.
5-40
Troubleshooting
5-5-6-3 Abnormal Printing
• Description : The printing is not working properly even when the cable has no problem.
(even after the cable is replaced) If the printer won't work at all or the strange fonts are
repeated, the printer driver may be defective or wrong setup in the CMOS Setup.
Check and Cause
Solution
1. Set up the parallel port in the CMOS SETUP.
1. Select SPP(Normal) or ECP LPT Port the among ECP,
EPP or SPP in the CMOS Setup.
2. Printer Driver Error.
2. Check the printer in My Computer.(to see if the printer driver
is compatible to the present driver or delete the old driver, if
defective and reinstall the new driver)
3. Error message from insufficient memory.
(The printing job sometimes stops or due to insufficient virtual memory, but it actually comes from the insufficient space
of the hard disk.)
3. Delete the unnecessary files to secure enough space of the
hard disk and start printing job again.
5-5-6-4 SPOOL Error
• Description : To spool which stands for "simultaneous peripheral operations online" a computer document or task list (or "job") is to read it in and store it, usually on a hard disk or larger
storage medium so that it can be printed or otherwise processed at a more convenient
time (for example, when a printer is finished printing its current document).
Check and Cause
Solution
1. Insufficient space of the hard disk in the directory assigned
for the basic spool.
1. Delete the unnecessary files to provide more space to start
printing job.
2. If the previous printing error not solved.
2. If there are some files with the extension name of ****.jnl,
Delete them and Reboot the Windows to restart printing job.
3. When expected to collide with other program.
3. Shut down all other programs except the current one, if possible.
4. When an application program or the printer driver is damaged.
4. Delete the printer driver completely and reinstall it.
5. When some files related to OS are damaged or virus
infected.
5 After rebooting the computer, check for viruses, restore the
damaged files and reinstall the program to do the printing
job.
6. Memory is less than suggested one.
6. Add up enough memory to the PC.
How to delete the data in the spool manager.
In the spool manager, the installed drivers and the list of the documents waiting to be printed are shown.
Select the document to be deleted and check the delete menu.
If you intend to delete the current document being printed, the data being transferred to the printer will be put
out and then the document is removed. Before choosing the document, the menu is still inactive.
Or put the document out of the list and repeat the routine as in the above or finish the spool manager.
5-41
Exploded Views and Parts List
6. Exploded View & Parts List
6-1. Main Exploded View & Parts List
2-1
2-2
1-1
(*SCX-5015)
1-1
(*SCX-5315F/
SCX-5115 )
2
22
20
1-2
25
1
3
39
47
6
34
4-2
28
4-3
5
4-1
7
4
46
16
45
35
12
44
15
8
43
41
41-2
41-3
40
24
13
41-1
41-4
41-5
41-6
26-1
37
17
21
21-1
21-2
14-5
38
14-2
11
30
37
14-1
14-4
9
26
53
53-2
53-153-3
26-3
48 49 50
26-3
26-2
14-3
23
51
18
33
14
42
29
52-3 52-2
52-1
18-1
36 (*SCX-5315F ONLY
27 (*SCX-5315F ONLY)
18-2
19
52
52-4
10
6-1
Samsung Electronics
Exploded Views and Parts List
Main Parts List
NO
1
1-1
1-2
DESCRIPTION
SEC CODE
Q’TY
SA
REMARK
SCANNER ASS’Y
JC96-02723A
1
O
SCX-5315F
SCANNER ASS’Y
JC96-02745A
1
O
SCX-5115
SCANNER ASS’Y
JC96-02787A
1
O
SCX-5015
ELA HOU-ADF ASS’Y
JC96-02742A
1
X
SCX-5315F/5115
MEA UNIT-PLATEN COVER ASS’Y
JC96-02750A
1
X
SCX-5015
ELA HOU-PLATEN ASS’Y
JC96-02754A
1
X
SCX-5315F
ELA HOU-PLATEN ASS’Y
TBD
1
X
SCX-5115/5015
2
MEA UNIT-COVER PA EXIT ASS’Y
JC97-01556B
1
O
2-1
PMO-TRAY EXTENTION MP NE
JC72-00354B
1
O
2-2
PMO-COVER PAPER EXIT
JC72-00786B
1
O
3
MEC-CASSETTE ASS’Y(LETTER)
JC97-01733A
1
O
USA Ver.
MEC-CASSETTE ASS’Y(A4)
JC97-01734A
1
O
Europe Ver.
4
MEA UNIT-COVER FRONT ASS’Y
JC97-01735A
1
O
4-1
COVER-M-FRONT
JC63-00193A
1
X
4-2
MPR-NAME/PLATE XRX
TBD
1
O
4-3
PLATE-BADGE(XRX)
JC61-00777A
1
X
5
UNIT-LSU
JC59-00014B
1
O
6
SMPS-SMPS(V1)+HVPS
JC44-00031A
1
O
110V
SMPS-SMPS(V2)+HVPS
JC44-00035A
1
O
220V
7
ELA-OPC UNIT SET
JC96-02238A
1
O
8
ELA-TONER UNIT SET
JC96-02286A
1
O
Europe Ver.
ELA-TONER UNIT SET
JC96-02239A
1
O
US/CANADA Ver.
9
ELA HOU-PICKUP ASS’Y
JC96-02715A
1
O
10
ELA HOU-SIDE COVER ASS’Y
JC96-02183B
1
O
11
ELA HOU-MP ASS’Y
JC96-02182A
1
O
12
ELA HOU-BASE FRAME ASS’Y
JC96-02714A
1
X
SCX-5315F
ELA HOU-BASE FRAME ASS’Y
JC96-02714B
1
X
SCX-5115
MEC-FEED ASS’Y
JC75-00143A
1
O
13
14
ELA HOU-FUSER(110V)ASS’Y
JC96-02814A
1
O
110V
ELA HOU-FUSER(220V)ASS’Y
JC96-02815A
1
O
220V
LAMP-HALOGEN (110V)
4713-001170
1
O
110V
LAMP-HALOGEN(220V)
4713-001171
1
O
220V
14-2
THERMOSTAT
4712-000001
1
O
14-3
GEAR-FUSER
JC66-40913B
1
O
14-4
ACTUATOR ASS’Y
JC97-01611A
1
O
14-5
THERMISTOR-FUSER
JC14-00001A
1
O
15
ELA HOU-FRAME MAIN ASS’Y
JC96-02184A
1
O
16
MEC-EXIT ASS’Y
JC75-00145A
1
O
17
ELA HOU-DRIVE ASS’Y
JC96-02741A
1
O
18
MEA UNIT-COVER REAR ASS’Y
JC97-01557A
1
O
18-1
PMO-COVER SIMM,XRX
JC72-41224B
1
O
18-2
PMO-COVER REAR
JC72-00788A
1
O
14-1
6-2
Samsung Electronics
Exploded Views and Parts List
NO
SEC CODE
Q’TY
SA
PBA MAIN-MAIN
JC92-01479A
1
O
SCX-5315F
PBA MAIN-MAIN
JC92-01480A
1
O
SCX-5115/5015
PMO-CONNECT PAPER MFP
JC63-00215A
1
X
SCX-5315F
PMO-CONNECT PAPER MFP
JC63-00215B
1
X
SCX-5115/5015
21
ELA HOU-DUCT FAN
JC96-02311A
1
X
21-1
FAN-DC
JC31-00012A
1
O
21-2
PMO-DUCT FAN
JC72-00807A
1
X
22
SHEET-OVERLAY(ENGLISH)
JC63-00218A
1
O
SCX-5315F
SHEET-OVERLAY(ENGLISH)
JC63-00212A
1
O
SCX-5115/5015
SHEET-OVERLAY(SPANISH)
JC63-00218B
1
O
SCX-5315F
SHEET-OVERLAY(SPANISH)
JC63-00212B
1
O
SCX-5115/5015
23
CBF POWER STITCH GRAY
JC39-00055B
1
X
24
SOLENOID-PICK UP
JC33-00007A
1
O
25
PMO-COVER EXIT REAR
JC72-00790A
1
O
26
MEA UNIT GUIDE CST PA ASS’Y
JC97-01575A
1
O
26-1
PMO-SHEET GUIDE PAPER
JC72-00836A
1
X
26-2
PMO-GUIDE CASSETTE RAIL
JC72-00791A
1
X
27
PBA LIU
JC92-01355A
1
O
USA/CANADA
PBA LIU
JC92-01355B
1
O
Western Europe
PBA LIU
JC92-01355C
1
O
Eastern Europe
PBA LIU
JC92-01355C
1
O
Eastern Europe
28
PMO-DUMMY BASE FRAME
JC72-00789A
1
X
29
IPR-SHIELD MAIN LOWER
JC63-00188A
1
X
30
PMO-COVER FEED AY
JC72-00801A
1
X
31
PMO-COVER BRKT MOTER
JC72-00834A
1
O
32
PMO-GUIDE PAPER OUT
JC72-00835A
1
O
33
PMO-DUCT FAN
JC72-00807A
1
X
34
CBF HARNESS-LSU
JC39-00163A
1
X
35
CBF HARNESS-POWER+HVPS
JC39-00162A
1
X
36
CBF HARNESS-LIU
JB39-00104A
1
X
37
CBF HARNESS-LIU GND
JB39-00103A
2
X
38
CBF HARNESS-INLET(XEROX)
JC39-00172A
1
X
39
IPR-SHIELD SMPS UPPER
JC70-00248A
1
X
40
PMO-BUSHING P/U.MP
JC72-41360A
1
X
41
MEA UNIT-PICKUP ROLLER
JC97-01730A
1
41-1
RUBBER-ROLLER PICKUP
JC73-00145A
1
O
41-2
RING-E
6044-000231
2
X
41-3
SHAFT-PICK_UP SUB
JC66-00596A
1
X
41-4
SHAFT-PICK_UP MAIN
JC66-00595A
1
X
41-5
HOUSING-PICK_UP
JC61-00711A
1
O
41-6
RING-E
6044-000125
1
X
42
SUPPORTER(T20N)
6103-001048
2
X
43
PMO-WINDOW SENSOR DEVE
JC72-00792A
1
X
19
20
DESCRIPTION
Samsung Electronics
REMARK
X
6-3
Exploded Views and Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
44
PMO-CAM JAM REMOVE
JC72-00799A
1
O
45
PMO-LOCKER DEVE
JC72-00805A
1
O
46
PMO-LEVER JAM REMOVE
JC72-00804A
1
O
47
IPR-SHIELD SMPS LOWER
JC70-00247A
1
X
48
GEAR-PICK-UP
JC66-00335A
1
O
49
PMO-BEARING SHAFT
JC72-41191A
1
X
50
GEAR-TRANSFER
JC66-40947A
1
O
51
MEC-ROLLER TRANSFER
JC75-00148A
1
O
52
MEA UNIT-HOLDER GEAR ASS’Y
JC97-01573A
1
O
52-1
SPRING ETC-PLATE TR
JC61-70203A
1
X
52-2
SPRING ETC-TR_L
JC61-70961A
1
X
52-3
PMO-BUSH
JC72-40228A
1
X
52-4
PMO-HOLDER GND TR
JC72-00883A
1
X
53
MEA UNIT-HOLDER GND ASS’Y
JC97-01574A
1
O
53-1
SPRING ETC-TR_R
JC61-70906A
1
X
53-2
PMO-BUSH
JC72-40228A
1
X
53-3
PMO-HOLDER GEAR TR
JC72-00884A
1
X
6-4
REMARK
Samsung Electronics
Exploded Views and Parts List
6-2. Platen Ass’y Exploded View & Parts List
1-1-1
3-1
1-1-2
1-1
S1
1-1-3
S1
1-1-4
3-6
0
1-2
1
3-8
3-2
3-4
3-7
3
3-10
3-11
3-3
3-5
1-3
3-12
3-9
1-4
S2
1-4
1-5-1
S2
1-4
S2
1-5-2
1-5
2-17
2-1
2-16
2-6
2-14
2-15
2-13
2-2
2-6
2-19
2-18
2-5
2-4
2-7-4
2-7-4
2-7-5
2-20
2-23
2-7-3
2
2-21
2-8
2-7-1
2-7
2-22 2-7-2
2-3
2-9
2-11
2-10
2-12
Samsung Electronics
6-5
Exploded Views and Parts List
Platen Ass’y Parts List
NO
0
1
DESCRIPTION
SEC CODE
Q’TY
SA
ELA HOU-PLATEN ASS’Y
JC96-02754A
1
X
SCX-5315F
ELA HOU-PLATEN ASS’Y
TBD
1
X
SCX-5115/5015
MEA UNIT-SCAN UPPER ASS’Y
TBD
1
O
1-1
A/S MATERAL-DUMMY UPPER ASS’Y
JC81-00426A
1
O
1-1-1
MCT-GLASS ADF
JC74-00019A
1
X
1-1-2
LABEL(L)-REGISTRATION EDGE (L)
JB68-00469A
1
X
1-1-3
PMO-DUMMY UPPER
JC72-00759A
1
X
1-1-4
SHEET-DUMMY UPPER
JC63-00074A
1
X
1-2
LABEL(R)-REGISTRATION EDGE (R)
JC72-00809A
1
X
1-3
PMO-COVER SCAN UPPER
JC72-00758A
1
X
1-4
IPR-HOLDER GLASS
JB70-00148A
3
X
1-5
MEA UNIT-GLASS PLATEN ASS’Y
JC97-01580A
1
X
1-5-1
LABEL(P)-SHEET SHADING
JB68-00419A
1
X
1-5-2
MCT-GLASS SCANNER(LEGAL)
JC74-00018A
1
X
ELA HOU-SCAN LOWER
JC96-02706A
1
X
2-1
BELT-TIMING GEAR
6602-001090
1
O
2-2
SPRING ETC-BELT
JB61-00059A
1
O
2-3
CBF HARNESS-OPE
JC39-00167A
1
X
2-4
CBF HARNESS-MAIN-ENGINE
JC39-00030A
1
X
2-5
CBF HARNESS-DRIVER GND
JB39-00065A
1
X
2-6
PBA SUB-D_SUB
JC92-01381A
1
X
2-7
ELA HOU-SCAN MOTOR
JC81-01694A
1
O
2-7-1
MOTOR STEP-SCAN
JB31-00011A
1
X
2-7-2
BRACKET-MOTOR PLATEN
JC61-00702A
1
X
2
2-7-3
GEAR-TIMING
JC66-00531A
1
X
2-7-4
RING-E
6044-000125
3
X
2-7-5
GEAR-REDUCTION73/37
JC66-00530A
1
X
2-8
COVER-M-CCD CABLE
JC63-00158A
1
X
2-9
COVER-SCAN LOWER(UMAX)
JC63-00157A
1
X
2-10
IPR-CHANNEL BASE FRAME
JC70-00239A
2
X
2-11
HOLDER-M-CCD(UMAX)
JC61-00703A
1
X
2-12
PMO-COVER DUMMY LOWER(C)
JC72-00794A
1
X
2-13
ICT-INSERT SHAFT
JB70-00154A
1
X
2-14
PMO-PULLEY
JB72-00763A
1
X
2-15
PMO-HOLDER BELT
JB72-00764A
1
X
2-16
RING-E
6044-000125
1
X
2-17
SHAFT-CCD(UMAX)
JC66-00532A
1
X
2-18
PMO-LEVER SENSOR
JC72-00755A
1
O
2-19
IPR-BRK SCAN BD
JC70-00228A
1
O
2-20
SPRING ETC-EXIT
JB61-70939A
1
X
21
ELA HOU-CCD MODULE
JC96-02759A
1
O
6-6
REMARK
Samsung Electronics
Exploded Views and Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
REMARK
2-22
CBF SIGNAL-CCD FFC
JC39-00236A
1
O
2-23
CBF HARNESS-SCAN MOTOR
JB39-00077A
1
X
ELA HOU-OPE CVER ASS’Y
JC96-02172B
1
O
SCX-5315F
ELA HOU-OPE CVER ASS’Y
JC96-02632B
1
O
SCX-5115/5015
3-1
PMO-OPE COVER
JC72-00756A
1
O
3-2
RMP-RUBBER FUNCTION
JC73-00092A
1
O
3-3
RMO-RUBBER TEL
JC73-00043A
1
O
3-4
PMO-KEY TEL
JC72-00452B
1
O
3-5
RMO-RUBBER SCROLL
JC73-00044A
1
O
3-6
PMO-KEY FUNCTION(A)
JC72-00754B
1
O
SCX-5315F
PMO-KEY FUNCTION(C)
JC63-00079A
1
O
SCX-5115/5015
3-7
PMO-KEY SCROLL
JC72-00453C
1
O
3-8
PMO-KEY FUNCTION(B)
JC72-00455B
1
O
3-9
PBA-OPE(FRO)
JC81-00433A
1
O
3-10
PMO-KEY REPORT
JC72-00457B
1
O
3-11
PMO-KEY STOP
JC72-00451B
1
O
3-12
PMO-KEY START
JC72-00450B
1
O
3
Samsung Electronics
SCX-5315F ONLY
6-7
Exploded Views and Parts List
6-3. ADF Ass’y or Platen Cover Ass’y Exploded View & Parts List
0
7
ADF Ass’y
8
10
10
9
5
1
2
2-1
1-1
6
1-2
2-2
1-3
1-5
2-3
2-4
1-4
2-5
3-22
4-1
3-1
4-4
4-3
S1
4-5
4-11
4-6
S1
3-17
3-2
3-3
4-8
3-21
4-7
4-9
3-2
3-7
1-6
4-2
3-4
3-19
3-8
3-2
1-12
3-5
3-18
1-13
3-6
1-4
4
3-4
1-10
1-15
7
3-12
3-20
1-8
1-9
3
3-11
3-10
3-9
1-11
3-15
3-13
3-13
3-14
Platen Cover Ass’y
2
4
0
1
3
6-8
Samsung Electronics
Exploded Views and Parts List
ADF Ass’y Parts List : SCX-5315F Only
NO
DESCRIPTION
SEC CODE
Q’TY
SA
REMARK
SCX-5315F/5115
0
ELA HOU-ADF ASS’Y
JC96-02750A
1
X
1
MEC UNIT-PLATEN COVER ASS’Y
JC96-02722A
1
O
1-1
PMO-TX STACKER
JC72-00745A
1
O
1-2
IPR-WASHER SPRING CY
JF70-10616A
2
X
1-3
PMO-DOC GUIDE L
JC72-00839B
1
O
1-4
PMO-DOC GUIDE R
JC72-00838B
1
O
1-5
GEAR PINION
JF72-41354A
1
X
1-6
MEA UNIT-HINGE
JC97-01731A
2
O
1-7
ROLLER EXIT
JC73-00091A
2
X
1-8
IPR-SHAFT EXIT
JC72-00242A
1
X
1-9
NPR-SPRING PINCH DRIVE
JB71-00038A
2
X
1-10
PMO-COVER PLATEN
JC72-00738A
1
X
1-11
PPR-SPONG SHEET
JC72-00751A
1
O
1-12
PPR-SHEET PLATEN
JC72-00750A
1
X
1-13
IPR-SPRING PINCH
JC70-00260A
3
X
1-14
IPR-SHAFT PINCH
JC70-00265A
3
X
1-15
PMO-ROLL PINCH
JG72-40663A
3
X
MEA UNIT-ADF UPPER ASS’Y
JC97-01581A
1
O
2-1
COVER ADF UPPER
JC72-00736A
1
X
2-2
ADF RUBBER
JC73-00052A
1
O
2-3
HOLDER ADF
JB72-00825A
1
O
2-4
SPONG ADF
JB73-00913A
1
X
2-5
SPRIG ADF
JB61-00009A
1
X
MEA UNIT-ADF LOWER ASS’Y
JC81-00434A
1
O
3-1
SPRING TORSION DOC
JB61-00076A
1
X
3-2
E-RING
6044-000159
3
X
3-3
GEAR-ADF 38
JB66-00103A
1
X
3-4
PMO-BUSH
JB72-00819A
2
O
3-5
MEC-ROLLER DRIVE
JC75-00149A
1
O
3-6
COVER ADF LOWER
JC72-00735A
1
X
3-7
PMO-ACTUATOR SENSOR DOC.
JC72-00837A
1
O
3-8
PMO-ACTUATOR SENSOR REGI
JB72-00747A
1
O
3-9
MEC-ROLLER EXIT
JC75-00150A
1
O
3-10
BUSHING HOLDER
JG72-40732A
1
X
3-11
SPRING CLUTCH
JC61-00062A
1
X
3-12
GEAR-EXITE 23
JC66-00323A
1
X
3-13
SPRING WHITE BAR
TBD
2
X
3-14
BRKT WHITE BAR
JC70-00225A
1
O
3-15
PPR-WHITE BAR SHEET
JC72-00752A
1
O
3-16
PMO-ACTUATOR SENSOR REGI
JC72-00747A
1
X
3-17
PBA SUB-ADF
JC81-00437A
1
O
2
3
Samsung Electronics
6-9
Exploded Views and Parts List
ADF Ass’y Parts List(Cont.) : SCX-5315F / SCX- 5115
NO
DESCRIPTION
SEC CODE
Q’TY
SA
3-18
PBA SUB-ADF POS SEN
JC92-01365A
1
O
3-19
PBA SUB-ADF DET SEN
JC92-01366A
1
O
3-20
CBF HARNESS-ADF ROLLER GND
TBD
1
X
3-21
CBF HARNESS-DRIVER GND
JB39-00065A
1
X
3-22
PMO-ACTUATOR SENSOR SCAN
JC72-00746A
1
O
MEA UNIT-ADF MOTOR ASS’Y
JC81-00435A
1
O
4-1
GEAR CLUTCH 29
JB66-00101A
1
X
4-2
BRKT ADF MOTOR
JC70-00224A
1
X
4-3
PMO-WHITE CLUTCH SUB 29
JB72-00844A
1
X
4-4
GEAR-CLUTCH IDLE 39
JC66-00322A
1
X
4-5
GEAR DOUBLE 33/20
JG61-40038A
2
X
4-6
E-RING
6044-000159
6
X
4-7
GEAR-DOUBLE 17/35
JG66-40039A
2
X
4-8
GEAR IDLE 25
JG66-40036A
1
X
4-9
MOTOR ADF
JC31-00017A
1
X
4-10
GEAR-JAM REMOVE
JC66-00329A
1
X
4-11
GEAR REDUCTION45/19
JC66-00324A
1
X
5
MEC UNIT-PICK UP ASS’Y
JC97-01582A
1
O
6
CBF HARNESS-D-SUB
JC39-00190A
1
O
7
PMO-COVER OPEN
JC72-00737A
1
O
8
PMO-COVER SIDE L
JC72-00739A
1
O
9
PMO-COVER SIDE R
JC72-00740A
1
O
10
PMO-GUIDE PAPER
JC72-00843A
2
O
S1
SCREW-TAPTITE
6003-000269
2
X
4
REMARK
Platen Cover Ass’y Parts List : SCX-5015 Only
NO
DESCRIPTION
SEC CODE
Q’TY
SA
REMARK
SCX-5015 Only
0
MEA UNIT-PLATEN COVER ASS’Y(C)
JC97-01680B
1
O
1
PMO-COVER PLATEN(C)
JC72-00873A
1
O
2
PMO-COVER DUMMY PLAEN
JC72-00874B
1
O
3
PPR-SPONG SHEET
JC72-00751A
1
O
4
MEA UNIT-HINES ASS’Y(C)
JC97-01681A
2
O
6-10
Samsung Electronics
Exploded Views and Parts List
6-4. Side Cover Ass’y Exploded View & Parts List
1
5
15
1-4 1-4
11-4
14
13
1-2
1-5
11
2
4
0
17
3
1-8
1-8
1-10
1-11
1-10
9
1-6
19
1-9
1-3
1-9
1-3
1-7
6
8
1-1
10-2
10-7
10-3
7
10-4
12
10-6
10-5
10
Samsung Electronics
6-11
Exploded Views and Parts List
Side Cover Ass’y Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
0
ELA HOU-SIDE COVER ASS'Y
JC96-02183B
1
O
1
MEA UNIT-DUPLEX ASS'Y
JC97-01578A
1
X
1-1
PMO-GUIDE DP SIDE
JC72-00806A
1
X
1-2
RING-CS
6044-000001
2
X
1-3
SPRING-FUSER EXIT
JC61-70976A
2
X
1-4
GEAR-DUP IDLER 17
JC66-00341A
3
X
1-5
GEAR-MP/DUP DRV
JC66-00346A
1
X
1-6
IPR-BRKT G DUP
JC70-00233A
1
X
1-7
PMO-GP LOWER DP
JC72-00732A
1
X
1-8
PMO-SHAFT DUP DRIVER
JC72-00764A
2
X
1-9
PMO-ROLLER_EXIT
JC72-40361A
2
X
1-10
RPR-RUBBER EXIT
JC73-10203A
2
X
1-11
PMO-BUSHING TX(B4)
JG72-40744A
4
X
1-12
PMO-TIE STOPPER
JC72-00766A
2
X
2
IPR-PLATE SAW
JC70-10232A
2
X
3
PMO-FEED FRAME
JC72-00731A
1
X
4
PMO-HOLDER SAW
JC72-41213A
1
X
5
IPR-BRACKET GUIDE A
JC70-00229A
1
X
6
PMO-LOCKER SIDE R
JC72-00763A
1
O
7
PMO-LOCKER OPEN
TBD
1
O
8
SPRING-LOCKER TORSION
JC61-00479A
1
O
9
SPRING-FEED
JC61-00478A
2
O
10
MEC UNIT-TRAY ASS’Y
JC97-01577A
1
O
10-1
PMO-TRAY CASE, MP
JC72-00776A
1
X
10-2
PMO-SIDE EXIT, MP
JC72-00778A
1
X
10-3
PMO-SIDE GUIDE, MP
TBD
1
X
10-4
PMO-TRAY COVER, MP
JC72-00777A
1
X
10-5
IPR-GUIDE LATCH, MP
JB70-10906A
1
X
10-6
PMO-TRAY LINK,MP
JC72-00857A
1
X
10-7
LABEL(R)-HEIGHT,MP
JC68-00697A
1
X
11
CBF HARNESS-OPE GND
JC39-00036A
1
X
12
PMO-TIE STOPPER
JC72-00766A
2
O
13
IPR-BRKT GROUND B
JC70-00230A
1
X
14
IPR-BRKT GROUND TR
JC70-00231A
1
X
15
IPR-BRKT GROUND A
JC70-00232A
1
X
16
IPR-BRACKET GUIDE B
JC70-00234A
1
X
17
PMO-BUSHING FEED
JC72-00730A
1
X
6-12
REMARK
Samsung Electronics
Exploded Views and Parts List
6-5. Cassette Ass’y Exploded View & Parts List
0
11
3
13
16
13
7
S1
8
2
14
15
1
5
4
12
10
9
Samsung Electronics
6
6-13
Exploded Views and Parts List
Cassette Ass’y Parts List
NO
SEC CODE
Q’TY
SA
REMARK
MEC-CASSETTE ASS'Y(LETTER)
JC97-01733A
1
O
USA Ver.
MEC-CASSETTE ASS'Y(A4)
JC97-01734A
1
O
Europe Ver.
1
IPR-FINGE
JC70-00451A
1
X
2
IPR-GUIDE PLT PAPER
JC70-10923A
1
X
3
IPR-PLATE K/UP
JC70-00221A
1
X
4
IPR-SPR PLT G/SIDE
JC70-00451A
1
O
5
PMO-COVER CASSETTE
JC72-00713A
1
X
6
PMO-FRAME CASSETTE
JC72-00716A
1
X
7
PMO-GUIDE FRONT CST
JC72-00798A
1
X
8
PMO-GUIDE REAR
JC72-00717A
1
O
9
PMO-GUIDE/SIDE CST
JC72-40967D
1
O
10
PMO-LOCKER PLATE
JC72-41210A
1
O
11
PRP-PAD CAST
JC73-10910A
2
O
12
SPRING-LOCKER PLATE
JG61-70531A
1
O
13
SPRING-PLATE K/UP
JC61-00455A
2
O
14
LABEL(R)-INSTRUCTION CST
JC68-00692A
1
X
15
LABEL(R)-HEIGHT CST
JC68-00709A
1
X
16
SHEET-CASSETTE
JC63-00216A
1
X
0
6-14
DESCRIPTION
Samsung Electronics
Exploded Views and Parts List
6-6. Exit Ass’y Exploded View & Parts List
10
7
6
10
5
8
6
4
5
4
10
10
19
20
11
S1
1
17
15
16
18
3
13
12
14
2
S1
Samsung Electronics
6-15
Exploded Views and Parts List
Exit Ass’y Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
0
MEC-EXIT ASS'Y
JC75-00145A
1
O
1
PMO-GUIDE-EXIT UPPER
JC72-00708A
1
X
2
PMO-GUIDE-EXIT LOWER
JC72-00710A
1
X
3
PMO-GUIDE-JAM REMOVE
JC72-00712A
1
X
4
MEC-ROLLER EXIT DRV
JC75-00127A
2
O
5
PMO-ROLLER DECURL
JC72-00833A
4
O
6
PMO-PULLEY DUPLEX
JC72-40980A
2
X
7
BELT-TIMING GEAR
6602-001084
1
X
8
GEAR-DUPLEX
JC66-40912A
1
X
9
PMO-BEARING LARGE DP
JC72-40978A
1
X
10
PMO-BEARING LARGE DP
JC72-40978A
4
O
11
IPR-GROUND-EXIT
JC70-00252A
1
X
12
ICT-SHAFT-EXIT LOWER ID
JC70-00274A
1
X
13
PMO-ROLLER_EXIT
JC72-40361A
4
X
14
SPRING-EXIT ROLL FD
JC61-70911A
2
X
15
PMO-HOLDER EXIT ROLL
JC72-41006A
4
X
16
PMO-ROLLER FD F
JC72-41007A
4
X
17
PMO-ROLLER FD R
JC72-41008A
4
X
18
SPRING-EXIT LOWER IDLE
JC61-00484A
4
X
19
MEC- BRUSH ANTISTATIC
JC75-00095A
1
O
20
PBA SUB-BIN-FULL SENSOR
TBD
1
X
S1
SCREW-TAPTITE
6003-000196
3
X
6-16
REMARK
Samsung Electronics
Exploded Views and Parts List
6-7. Feeder Ass’y Exploded View & Parts List
2
17
1
6
5
4
7
11
19
12
10
9
12
13
5
8
15
17
6
3
19
18
12
S1
14
Samsung Electronics
6-17
Exploded Views and Parts List
Feeder Ass’y Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
0
MEC-FEED ASS'Y
JC75-00143A
1
O
1
PMO-FRAME FEED
JC72-00821A
1
X
2
GEAR-FEED
JC66-00332A
1
X
3
GEAR-MP/DUP DRV
JC66-00346A
1
X
4
ICT-SHAFT FEED
JC70-00267A
1
X
5
PMO-BUSHING_P/U,MP
JC72-41364A
1
X
6
RING-E
6044-000125
2
X
7
RING-CS
6044-000001
1
X
8
PMO-BRKT FEED
JC72-00720A
1
X
9
PMO-ROLLER FEED
JC72-00727A
1
O
10
PMO-HOLDER PINCH C
JC72-00723A
1
X
11
PMO-HOLDER PINCH SUB
JC72-00725A
1
X
12
PMO-ROLLER FEED L
JC72-40261A
3
X
13
SPRING-FEED CAST
JC61-00480A
1
X
14
PMO-HOLDER PINCH M
JC72-00724A
1
X
15
PMO-SUB HOLDER FEED
JC72-40266A
1
X
16
SPRING-FEED MP
JC61-00481A
1
X
17
WASHER-PLAIN
6031-000021
2
X
18
PMO-ROLLER FEED S
JC72-40262A
1
X
19
IPR-SHAFT FEED IDLER
JC70-10230A
4
X
S1
SCREW-TAPTITE
6003-000196
3
X
6-18
REMARK
Samsung Electronics
Exploded Views and Parts List
6-8. MP Ass’y Exploded View & Parts List
22
16
3
6
20
9
18
5
21
10
14
20
1
8
25
25
3
4
2
12
11
13
17
15
24
Samsung Electronics
7
23
19
6-19
Exploded Views and Parts List
MP Ass’y Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
0
ELA HOU-MP ASS'Y
JC96-02182A
1
O
1
SCREW-TAPTITE
6003-000119
2
X
2
SCREW-TAPTITE
6003-000266
1
X
3
RING-E
6044-000125
2
O
4
SOLENOID-MP
JC33-00006A
1
O
5
SPRING--CAM MP
JC61-00003A
1
O
6
SPRING-PICK UP MP
JC61-00041A
1
X
7
SPRING-KNOCKUP,MP
JC61-00483A
1
O
8
IPR-BRACKET SOLENOIDE
JC70-00237A
1
X
9
PMO-HOLDER CAM MPF
JC72-00055A
1
X
10
PMO-GEAR P/U MPF
JC72-00056A
1
X
11
PMO-ROLLER CAM.MP
JC72-00761A
1
X
12
PMO-ACTUATOR,MP
JC72-00767A
1
O
13
PMO-ADJUSTER,MP
JC72-00768A
1
O
14
PMO-CAM PICK UP,MP
JC72-00769A
1
O
15
PMO-FRAME,MP
JC72-00770A
1
X
16
PMO-HOLDER PAD,MP
JC72-00771A
1
O
17
PMO-HOLDER SENSOR,MP
JC72-00772A
1
O
18
PMO-HOUSING PICK UP,MP
JC72-00773A
1
X
19
PMO-PLATE KNOCK UP,MP
JC72-00775A
1
X
20
PMO-IDLE PICK UP,MP
JC72-41027A
2
O
21
RPR-RUBBER PICK UP,MP
JC73-00089A
1
X
22
RPR-RCT-PAD-PICKUP,MP
JC73-00090A
1
O
23
RPR-PAD KNOCK UP,MP
JC73-10906A
1
O
24
PBA SUB-MP SEN
JC92-01362A
1
O
25
PMO-BUSHING PICKUP,MP
JC72-41364A
1
O
26
A/S MATERAL-PICKUP,MP
JC81-00427A
1
O
6-20
REMARK
Samsung Electronics
Exploded Views and Parts List
6-9. Base Frame Exploded View & Parts List
1
14
20
17
1
8
16
19
2
9
15
11
6
1
10
5
7
1
3
12
13
4
18
11
Samsung Electronics
1
5
6-21
Exploded Views and Parts List
Base Frame Parts List
NO
SEC CODE
Q’TY
SA
ELA HOU-BASE FRAME
JC96-02818A
1
X
SCX-5315F
ELA HOU-BASE FRAME
JC96-02818B
1
X
SCX-5115
1
SCREW-TAPTITE
6003-000196
5
X
2
SCREW-TAPTITE
6003-000269
2
X
3
SCREW-TAPTITE
6003-001256
4
X
4
SPRING ETC-TORSION
JC61-00486A
1
X
5
FOOT-ML80
JC61-40001A
2
O
6
CAM-CATCH
JC66-00050A
1
X
7
IPR-CHANNEL BASE FRAME
JC70-00239A
1
X
8
IPR-GROUND PLATE A(OPC)
JC70-00240A
1
O
9
IPR-GROUND PLATE B(BASE)
JC70-00241A
1
O
10
PMO-BASE FRAME
JC72-00779A
1
X
11
PMO-BRACKET PUSH DEVE
JC72-00780A
2
X
12
PMO-BRACKET SIDE OPEN
JC72-00781A
1
O
13
PMO-COVER FRONT DUMMY
JC72-00785A
1
X
14
ELA M/M-AUD SPEAKER
JC96-01607A
1
O
15
SPRING ETC-DEVE REAR
JC61-00550A
1
X
16
CBF HARNESS-OPC GND
JC39-00179A
1
X
17
FAN-DC(LSU)
JC31-00026A
1
X
18
SPRING ETC-DEVE FRONT
JC61-00551A
1
X
19
SHEET-BASE FRAME
JC63-00242A
2
X
20
SCREW-TAPPING
6002-000209
2
X
0
DESCRIPTION
REMARK
O: Service available X: Service not available
6-22
Samsung Electronics
Exploded Views and Parts List
6-10.Pick-up Ass’y Exploded View & Parts List
11
6
10
15
9
7
5
12
1
8
3
2
Samsung Electronics
4
6-23
Exploded Views and Parts List
Pick-up Ass’y Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
0
ELA HOU-PICKUP ASS'Y
JC96-02715A
1
O
1
IPR-GND FEED
JC70-00238A
1
X
2
IPR-GND INPUT
JC70-00235A
1
O
3
IPR-GUIDE INPUT
JC70-00222A
1
O
4
PMO-ACTUATOR EMPTY
JC72-00719A
1
O
5
PBA SUB-TONER_TX
JC92-01359A
1
O
6
PBA SUB-PTL
JC92-01361A
1
O
7
PMO-FEED SENSOR
JC72-00721A
1
X
8
PMO-GUIDE PAPER
JC72-00722A
1
X
9
PMO-HOLDER SENSOR FEED
JC72-00726A
1
X
10
PMO-LENS TONER SENSOR
JC72-00803A
1
X
11
PMO-PTL PATH
JC72-00822A
1
X
12
PBA SUB-FEED+P.EMP SEN.
JC92-01363A
1
O
6-24
REMARK
Samsung Electronics
Exploded Views and Parts List
6-11. Drive Ass’y Exploded View & Parts List
5
8
4
6
9
23
2
10
2
S2
23
1
11
S1
3
23
12
13
14
S2
15
23
20
23
17
23
Samsung Electronics
16
18
22
19
17
23
21
6-25
Exploded Views and Parts List
Drive Ass’y Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
0
ELA HOU-DRIVE ASS'Y
JC96-02741A
1
O
1
IPR-BRKT MOTOR
JC70-00257A
1
X
2
MOTOR-STEP
JC31-00020B
2
O
3
CBF-HARNESS-MOTOR
JC39-00165A
1
X
4
RING-E
6044-000159
1
X
5
SOLENOID-DUPLEX
JC33-00008A
1
O
6
SPRING SOLENOID DP
JC61-70915A
1
X
7
IPR-LINK SOLENOID
JC70-00258A
1
X
8
GEAR-EXIT/U,ID
JC66-40211B
1
X
9
GEAR-SWING DRV
JC66-00349A
1
X
10
GEAR-35/19
JC66-00350A
1
X
11
GEAR-71/23
JC66-00345A
1
X
12
GEAR-DEVE DRV
JC66-00338A
1
X
13
PMO-DEV/COUPLING
JC72-00743A
1
X
14
GEAR-RDCN,OPC
JC66-00351A
1
X
15
GEAR-86/23
JC66-00337A
1
X
16
GEAR-RDCN FEED OUTER
JC66-00343A
1
X
17
GEAR-HUB CLUTCH
JC66-00340A
2
X
18
GEAR-RDCN FEED INNER
JC66-00342A
1
X
19
GEAR-FEED DRV
JC66-00348A
1
X
20
GEAR-OPC DRV
JC66-00347A
1
X
21
GEAR-GEAR FUSER DRV OUTER
JC66-00334A
1
X
22
GEAR-FUSER DRV INNER
JC66-00333A
1
X
23
RING-E
6044-000231
8
X
S1
SCREW-TAPTITE
6003-000196
5
X
S2
SCREW-TAPTITE
6003-000269
7
X
6-26
REMARK
Samsung Electronics
Exploded Views and Parts List
6-12. Main Frame Ass’y Exploded View & Parts List
0
19
S5
S5
23
28
13
27
12
22
32
25
33
25 24
24
24
26 31
29.30
S4
16
20
18
17
9
10
8
S5
7
6
21
Samsung Electronics
1
2
15
S5
5
3
4
4
11
6-27
Exploded Views and Parts List
Main Frame Ass’y Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
0
ELA HOU-FRAME MAIN ASS’Y
JC96-02184A
1
O
1
PMO-HOUSING TERMINAL
JC72-00802A
1
O
2
IPR-TERMINAL BLADE
JC70-00269A
2
X
3
IPR-TERMINAL SUPPLY
JC70-00270A
2
X
4
IPR-TERMINAL TR
JC70-00271A
1
X
5
IPR-TERMINAL GND
JC70-00272A
1
X
6
IPR-TERMINAL DEVE KEY
JC70-00273A
2
X
7
CBF-HARNESS-DEV-ID
JC39-00166A
1
X
8
CBF-HARNESS-BLADE+SUPPLY+DEV
JC39-00170A
5
X
9
CBF-HARNESS-MAIN-THV WIRE
JC39-00168A
1
X
10
CBF-HARNESS-MAIN-MHV WIRE
JC39-00169A
1
X
11
PMO-FRAME MAIN
JC72-00800A
1
X
12
PMO-LENS TONER SENSOR
JC72-00803A
2
X
13
IPR-GND EXIT
JC70-00214A
1
X
14
IPR-GND OPC
JC70-00216A
1
X
15
IPR-GND OPC BASE
JC70-00217A
1
X
16
IPR-GND FUSER
JC70-00215A
1
X
17
IPR-GUARD C/O S/W
JC70-00218A
1
X
18
IPR-GND TERMINAL
JC70-00219A
1
X
19
CBF HARNESS-AC WIRE
JC39-00171A
1
X
20
CBF-HARNESS;SWITCH-MICRO
JC81-00438A
2
O
21
CBF-HARNESS MOTOR
JB39-00017A
1
X
22
PBA SUB-EXIT SENSOR
JC92-01364A
1
O
23
PBA SUB-TONER_RX
JC92-01360A
1
O
24
GEAR-EXIT/U,ID
JC66-40211B
3
X
25
GEAR-EXIT,IDLE(Z17)
JC66-40964A
2
X
26
CBF-HARNESS THERMISTOR_JOINT
JC39-00164A
1
O
27
PMO-HOUSING TERMINAL
JC72-41010A
1
X
28
IPR-TERMINAL FU
JC70-10961A
2
X
29
PMO-CAP CONNECTOR L
JC72-00463A
1
O
30
PMO-CAP CONNECTOR U
JC72-00465A
1
O
31
ELA HOU-MOTOR GND
JC96-01579A
1
X
32
SPRING-CLUTCH
JB61-70922A
2
X
33
RING-CS
6044-000001
5
X
S
SCREW-TAPTITE,M3*8 BLACK,BINDER
6003-000119
17
X
6-28
REMARK
Samsung Electronics
Exploded Views and Parts List
6-13. FuserAss’y Exploded View & Parts List
9
S2
S2
1
S2
13
S2
S2
S2
11
6-1
6-2
10
6
12
7
8
5
4
14
2
25
26
3
23
24
19
22
16
17
18
15
S2
17
20
16
21
27
S2
Samsung Electronics
6-29
Exploded Views and Parts List
FuserAss’y Parts List
NO
DESCRIPTION
SEC CODE
Q’TY
SA
REMARK
0
ELA HOU-FUSER(110V)ASS’Y
JC96-02739A
1
O
110V
0
ELA HOU-FUSER(220V)ASS’Y
JC96-02740A
1
O
220V
1
PMO-UPPER FUSER
JC72-00812A
1
X
2
RMO-ROLLER HEAT
JC73-00093A
1
X
3
PMO-BEARING H/R-F
JC72-00814A
1
X
4
BEARING-H/R L
JC66-10902A
1
X
5
GEAR-FUSER
JC66-40913B
1
O
6
MEA UNIT-CLAW ASS'Y
JC97-01577A
1
X
6-1
SPRING-SAPERATION
JC61-70909A
4
X
6-2
PMO-GUIDE CLAW
JC72-00376A
4
X
7
PEX-ROLLER EXIT F-UP
JC72-20901A
2
X
8
IPR-PIN ROLLER EXIT
JC70-00064A
2
X
9
NPR-ELECTRODE GEAR
JC71-00029A
1
X
10
NPR-ELECTRODE M
JC71-00030A
1
X
11
NPR-ELECTRODE F
JC71-00028A
1
X
12
THERMOSTAT
4712-000001
1
O
13
THERMISTOR-FUSER
JC14-00001A
1
O
14
LAMP-HALOGEN (110V)
4713-001170
1
O
110V
14
LAMP-HALOGEN(220V)
4713-001171
1
O
220V
15
PMO-LOWER FUSER
JC72-00820A
1
X
16
THERMISTOR-FUSER
JC14-00001A
1
X
17
BEARING-PRESSURE/R
JC66-10901A
2
X
18
RMO-ROLLER PRESSURE
JC73-00094A
1
X
19
PMO-LEVER JAM R
JC72-00819A
1
X
20
PMO-LEVER JAM F
JC72-00818A
1
X
21
PMO-GUIDE INPUT
JC72-00817A
1
X
22
IPR-GROUND FU
JC70-00259A
1
X
23
PMO-ACTUATOR EXIT
JC72-00810A
1
X
24
ACTUATOR ASS’Y
JC97-01611A
1
O
25
PMO-ARM ACTUATOR
JC72-00811A
1
X
26
SPRING-PR(7300)
JC61-00056A
2
X
27
LABEL(R)-HV FUSER
JC68-00407A
1
X
S1
SCREW-TAPTITE
6003-000119
8
X
S2
SCREW-TAPTITE
6003-000269
4
X
6-30
Samsung Electronics
Electrical Parts List
7. Electrical Parts Lists
7-1 Main PBA
Code No.
JC92-01479A
0202-000008
0202-000108
0202-000118
0202-001025
0203-001235
0203-001236
0204-000469
0401-000116
0401-000116
0401-000116
0401-000116
0401-000116
0401-000116
0401-000116
0401-000116
0402-000129
0402-000129
0402-000129
0402-000129
0402-000129
0402-000129
0402-000129
0402-000129
0403-000350
0404-000112
0404-000112
0404-000112
0404-000112
0404-000112
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0407-000101
0501-000010
Loc.
MAIN PBA
D12
D23
D25
D33
D34
D35
D37
D38
D13
D14
D15
D19
D20
D26
D39
D40
ZD1
D16
D21
D22
D24
D36
D1
D10
D11
D17
D18
D2
D27
D28
D3
D31
D32
D5
D6
D7
D8
D9
Q24
Samsung Electronics
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
PBA MAIN-MAIN
SOLDER-WIRE
SOLDER-CREAM
SOLDER-WIRE
SOLDER-WIRE FLUX
TAPE-PAPER
TAPE-PAPER
THINNER
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-ZENER
DIODE-SCHOTTKY
DIODE-SCHOTTKY
DIODE-SCHOTTKY
DIODE-SCHOTTKY
DIODE-SCHOTTKY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
DIODE-ARRAY
TR-SMALL SIGNAL
Specification
SCX-5315F,SEC,USA,15PPM,MFP,
S63S-W3.0,S63S,D3,63SN/37PB,RMA-010 T-322,S63,-,KR-19 RMA,-,D0.8,-,KS-611,-,-,-,spray
YW-692,T0.15,W5.8,L4000M,YW-4620,T0.12,W6.2,L4000M,#4662,-,0.795,MMSD914T1,100V,200mA,SOD-123,TP
MMSD914T1,100V,200mA,SOD-123,TP
MMSD914T1,100V,200mA,SOD-123,TP
MMSD914T1,100V,200mA,SOD-123,TP
MMSD914T1,100V,200mA,SOD-123,TP
MMSD914T1,100V,200mA,SOD-123,TP
MMSD914T1,100V,200mA,SOD-123,TP
MMSD914T1,100V,200mA,SOD-123,TP
1N4003,200V,1A,DO-41,TP
1N4003,200V,1A,DO-41,TP
1N4003,200V,1A,DO-41,TP
1N4003,200V,1A,DO-41,TP
1N4003,200V,1A,DO-41,TP
1N4003,200V,1A,DO-41,TP
1N4003,200V,1A,DO-41,TP
1N4003,200V,1A,DO-41,TP
UZ4.3B,4.3V,4.0-4.6V,500mW,DORB420D,25V,100mA,SOT-23,TP
RB420D,25V,100mA,SOT-23,TP
RB420D,25V,100mA,SOT-23,TP
RB420D,25V,100mA,SOT-23,TP
RB420D,25V,100mA,SOT-23,TP
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
DA204K,20V,100mA,C2-3,SOT-23,T
KSC1008,NPN,800mW,TO-92,TP,120-240
7-1
Electrical Parts List
Code No.
0501-000010
0501-000279
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0501-000338
0502-000245
0502-000245
0502-000245
0502-000245
0502-000245
0502-001048
0801-000379
0801-000477
0801-000477
0801-001090
0801-002095
0801-002095
0801-002326
0801-002326
0801-002326
0801-002446
0801-002449
0801-002591
0801-002591
0803-003263
0803-003263
0803-003263
0803-003263
1001-000170
1001-000171
1006-001224
1105-001464
1105-001464
1106-001332
1106-001453
1107-001286
1107-001286
1201-000105
7-2
Loc.
Q25
Q16
Q1
Q11
Q14
Q15
Q17
Q18
Q19
Q2
Q22
Q23
Q26
Q3
Q4
Q5
Q7
Q8
Q9
Q10
Q12
Q13
Q21
Q6
Q20
U27
U31
U37
U18
U32
U35
U22
U24
U56
U1
U4
U26
U38
U25
U5
U7
U8
U48
U47
U33
U40
U49
U55
U12
U43
U54
U39
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-POWER
TR-POWER
TR-POWER
TR-POWER
TR-POWER
TR-POWER
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-CMOS LOGIC
IC-TTL
IC-TTL
IC-TTL
IC-TTL
IC-ANALOG SWITCH
IC-ANALOG SWITCH
IC-LINE TRANSCEIVER
IC-DRAM
IC-DRAM
IC-SRAM
IC-SRAM
IC-FLASH MEMORY
IC-FLASH MEMORY
IC-AUDIO AMP
Specification
KSC1008,NPN,800mW,TO-92,TP,120-240
KSA1182-Y,PNP,150mW,SOT-23,TP,
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
2SC2812,NPN,200mW,SOT-23,TP,20
KSB1151-Y,PNP,1.3W,TO-126,-,16
KSB1151-Y,PNP,1.3W,TO-126,-,16
KSB1151-Y,PNP,1.3W,TO-126,-,16
KSB1151-Y,PNP,1.3W,TO-126,-,16
KSB1151-Y,PNP,1.3W,TO-126,-,16
KSD1691,NPN,1.3W,TO-126,BK,160
74HC00,NAND GATE,SOP,14P,150MI
74HCT273,D FLIP-FLOP,SOP,20P,3
74HCT273,D FLIP-FLOP,SOP,20P,3
74HC14,SCHIMITT INVERTER,SOP,1
74LCX245,BUFFERS,TSSOP,20P,173MIL,OCTAL,TP
74LCX245,BUFFERS,TSSOP,20P,173MIL,OCTAL,TP,
74LCX32,OR GATE,TSSOP,14P,173MIL,QUAD,TP,
74LCX32,OR GATE,TSSOP,14P,173MIL,QUAD,TP,
74LCX32,OR GATE,TSSOP,14P,173MIL,QUAD,TP,
74LCX14,SCHMITT INVERTER,TSSOP,14P,173MIL,HEX,TP,
74LVX4245,BUS TRANSCEIVER,TSSOP,24P,173MIL,OCTAL,TP,
74LVX273,D FLIP-FLOP,TSSOP,20P,173MIL,OCTAL,TP,
74LVX273,D FLIP-FLOP,TSSOP,20P,173MIL,OCTAL,TP,
74LCX07,HEX BUFFER,SOIC,14P,150MIL,SIX,TP,
74LCX07,HEX BUFFER,SOIC,14P,150MIL,SIX,TP
74LCX07,HEX BUFFER,SOIC,14P,150MIL,SIX,TP
74LCX07,HEX BUFFER,SOIC,14P,150MIL,SIX,TP,
MC14051BD,SPDT CMOS,SOP,16P,15
MC14053BD,SPDT CMOS,SOP,16P,15
74LVX161284,TSSOP,48P,240MIL,TRIPLE,TP,
K4S641632F,4MX16BIT,TSOP(II),54P,400MIL,7.5NS,3.3V,10%,
K4S641632F,4MX16BIT,TSOP(II),54P,400MIL,7.5NS,3.3V,10%,
6R1008,128Kx8Bit,SOJ,32P,400MIL,15nS,3.3V,10%
K6R1016V1D,64KX16BIT,TSOP(II),44P,400MIL,8NS,3.3V,10%,
29LV160,2Mx8Bit,TSOP,48P,724MIL,70nS,3V,10%,
29LV160,2Mx8Bit,TSOP,48P,724MIL,70nS,3V,10%,
34119,SOP,8P,150MIL,SINGLE,-,P
Samsung Electronics
Electrical Parts List
Code No.
1201-000167
1201-000167
1202-000164
1203-000157
1203-001455
1203-001455
1203-001455
1203-002220
1203-002233
1205-001771
1205-001771
1205-001771
1205-001896
1205-002258
2001-000016
2005-000168
2005-000168
2005-000168
2005-000168
2005-000168
2005-000168
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
Loc.
U45
U50
U3
U10
U51
U52
U9
U19
U20
U15
U21
U36
U42
U34
R56
R119
R144
R152
R175
R4
R5
R100
R102
R103
R11
R113
R12
R121
R125
R13
R131
R132
R136
R137
R139
R14
R140
R141
R143
R15
R155
R159
R16
R164
R166
R183
R192
R197
R198
R199
R202
R203
Samsung Electronics
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
IC-OP AMP
IC-OP AMP
IC-VOLTAGE COMP.
IC-POSI.ADJUST REG.
IC-POSI.FIXED REG.
IC-POSI.FIXED REG.
IC-POSI.FIXED REG.
IC-POSI.ADJUST REG.
IC-RESET
IC-CLOCK GENERATOR
IC-CLOCK GENERATOR
IC-CLOCK GENERATOR
IC-MODEM
IC-CLOCK GENERATOR
R-CARBON(S)
R-WIRE WOUND,NON
R-WIRE WOUND,NON
R-WIRE WOUND,NON
R-WIRE WOUND,NON
R-WIRE WOUND,NON
R-WIRE WOUND,NON
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
Specification
358,SOP,8P,150MIL,DUAL,100V/mV
358,SOP,8P,150MIL,DUAL,100V/mV
393,SOP,8P,150MIL,DUAL,36V,CMO
317,TO-220,3P,-,PLASTIC,1.2V/3
1117,DPAK,3P,265MIL,PLASTIC,3.
1117,DPAK,3P,265MIL,PLASTIC,3.
1117,DPAK,3P,265MIL,PLASTIC,3.
LD1117,DPAK,3P,240MIL,PLASTIC,1.25/15V,12W,
XC61F,SOT-23,3P,-,PLASTIC,0.7/10V,150MW,-,-,-,TP
FS781BZB,SOP,8P,150MIL,PLASTIC,5.5V,37mW,0to+70C,TP,FS781BZB,SOP,8P,150MIL,PLASTIC,5.5V,37mW,0to+70C,TP,FS781BZB,SOP,8P,150MIL,PLASTIC,5.5V,37mW,0to+70C,TP,FM336R6719-12,QFP,100P,-,PLASTIC,3.6V,250mW,0to+70C,TR,CY25814SC,SOIC,8P,150MIL,PLASTIC,3.6V,68MW,0TO+70C,-,1OHM,5%,1/2W,AA,TP,2.4X6.4MM
0.22ohm,5%,2W,AA,BK,4x12mm
0.22ohm,5%,2W,AA,BK,4x12mm
0.22ohm,5%,2W,AA,BK,4x12mm
0.22ohm,5%,2W,AA,BK,4x12mm
0.22ohm,5%,2W,AA,BK,4x12mm
0.22ohm,5%,2W,AA,BK,4x12mm
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
7-3
Electrical Parts List
Code No.
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000070
2007-000071
2007-000071
2007-000071
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000074
2007-000077
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
7-4
Loc.
R204
R206
R210
R211
R212
R216
R223
R226
R244
R287
R306
R307
R314
R36
R43
R60
R70
R87
R88
R305
R32
R37
R10
R118
R126
R142
R219
R23
R24
R251
R257
R283
R291
R302
R33
R34
R35
R38
R39
R40
R41
R42
R57
R8
R86
R9
R48
R124
R133
R157
R158
R171
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
Specification
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
0ohm,5%,1/16W,DA,TP,1608
22ohm,5%,1/16W,DA,TP,1608
22ohm,5%,1/16W,DA,TP,1608
22ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
100ohm,5%,1/16W,DA,TP,1608
470ohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
Samsung Electronics
Electrical Parts List
Code No.
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000078
2007-000080
2007-000082
2007-000082
2007-000082
2007-000083
2007-000083
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000084
2007-000086
2007-000086
2007-000086
2007-000086
2007-000086
2007-000086
2007-000086
2007-000086
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
Loc.
R177
R178
R217
R232
R241
R243
R245
R249
R28
R286
R81
R252
R120
R174
R229
R285
R92
R167
R182
R185
R195
R231
R25
R29
R295
R3
R215
R225
R246
R247
R298
R303
R64
R99
R106
R110
R112
R115
R130
R145
R146
R160
R176
R179
R18
R184
R186
R191
R193
R2
R20
R205
Samsung Electronics
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
Specification
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
1Kohm,5%,1/16W,DA,TP,1608
2Kohm,5%,1/16W,DA,TP,1608
3.3Kohm,5%,1/16W,DA,TP,1608
3.3Kohm,5%,1/16W,DA,TP,1608
3.3Kohm,5%,1/16W,DA,TP,1608
3Kohm,5%,1/16W,DA,TP,1608
3Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
4.7Kohm,5%,1/16W,DA,TP,1608
5.6Kohm,5%,1/16W,DA,TP,1608
5.6Kohm,5%,1/16W,DA,TP,1608
5.6Kohm,5%,1/16W,DA,TP,1608
5.6Kohm,5%,1/16W,DA,TP,1608
5.6Kohm,5%,1/16W,DA,TP,1608
5.6Kohm,5%,1/16W,DA,TP,1608
5.6Kohm,5%,1/16W,DA,TP,1608
5.6Kohm,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
7-5
Electrical Parts List
Code No.
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000090
2007-000091
2007-000091
2007-000092
2007-000092
2007-000092
2007-000094
2007-000094
2007-000094
2007-000094
2007-000094
2007-000094
2007-000094
2007-000094
2007-000094
2007-000096
2007-000096
2007-000096
7-6
Loc.
R213
R220
R254
R258
R26
R260
R263
R264
R265
R266
R267
R269
R27
R275
R288
R308
R309
R31
R310
R311
R312
R313
R44
R50
R51
R53
R54
R67
R68
R77
R78
R82
R83
R84
R96
R228
R234
R168
R253
R282
R1
R122
R123
R134
R153
R154
R277
R80
R90
R128
R138
R163
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
Specification
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
10KOHM,5%,1/16W,DA,TP,1608
12Kohm,5%,1/16W,DA,TP,1608
12Kohm,5%,1/16W,DA,TP,1608
15Kohm,5%,1/16W,DA,TP,1608
15Kohm,5%,1/16W,DA,TP,1608
15Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
22Kohm,5%,1/16W,DA,TP,1608
30Kohm,5%,1/16W,DA,TP,1608
30Kohm,5%,1/16W,DA,TP,1608
30Kohm,5%,1/16W,DA,TP,1608
Samsung Electronics
Electrical Parts List
Code No.
2007-000096
2007-000096
2007-000096
2007-000096
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000097
2007-000102
2007-000102
2007-000102
2007-000103
2007-000103
2007-000104
2007-000106
2007-000106
2007-000106
2007-000106
2007-000109
2007-000109
2007-000109
2007-000109
2007-000109
2007-000113
2007-000113
2007-000113
2007-000113
2007-000113
2007-000113
2007-000113
2007-000113
2007-000113
2007-000113
2007-000113
2007-000113
2007-000116
2007-000120
2007-000120
2007-000120
2007-000121
2007-000121
Loc.
R170
R276
R91
R93
R109
R111
R149
R19
R214
R22
R240
R242
R268
R280
R284
R290
R301
R69
R89
R161
R189
R278
R271
R297
R248
R187
R262
R272
R293
R117
R129
R237
R273
R294
R135
R180
R181
R190
R200
R201
R207
R208
R221
R233
R235
R236
R165
R116
R150
R151
R172
R279
Samsung Electronics
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
Specification
30Kohm,5%,1/16W,DA,TP,1608
30Kohm,5%,1/16W,DA,TP,1608
30Kohm,5%,1/16W,DA,TP,1608
30Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
47Kohm,5%,1/16W,DA,TP,1608
100Kohm,5%,1/16W,DA,TP,1608
100Kohm,5%,1/16W,DA,TP,1608
100Kohm,5%,1/16W,DA,TP,1608
120Kohm,5%,1/16W,DA,TP,1608
120Kohm,5%,1/16W,DA,TP,1608
150Kohm,5%,1/16W,DA,TP,1608
220Kohm,5%,1/16W,DA,TP,1608
220Kohm,5%,1/16W,DA,TP,1608
220Kohm,5%,1/16W,DA,TP,1608
220Kohm,5%,1/16W,DA,TP,1608
1Mohm,5%,1/16W,DA,TP,1608
1Mohm,5%,1/16W,DA,TP,1608
1Mohm,5%,1/16W,DA,TP,1608
1Mohm,5%,1/16W,DA,TP,1608
1Mohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
33ohm,5%,1/16W,DA,TP,1608
120ohm,5%,1/16W,DA,TP,1608
680ohm,5%,1/16W,DA,TP,1608
680ohm,5%,1/16W,DA,TP,1608
680ohm,5%,1/16W,DA,TP,1608
820ohm,5%,1/16W,DA,TP,1608
820ohm,5%,1/16W,DA,TP,1608
7-7
Electrical Parts List
Code No.
2007-000122
2007-000123
2007-000123
2007-000123
2007-000124
2007-000124
2007-000129
2007-000131
2007-000132
2007-000133
2007-000134
2007-000134
2007-000136
2007-000265
2007-000309
2007-000309
2007-000309
2007-000368
2007-000402
2007-000618
2007-000618
2007-000683
2007-000839
2007-000839
2007-000839
2007-000839
2007-000839
2007-000839
2007-000839
2007-000839
2007-000839
2007-000839
2007-000839
2007-000839
2007-000965
2007-000965
2007-000965
2007-001002
2007-001002
2007-001002
2007-001002
2007-001002
2007-001002
2007-001002
2007-001044
2007-001134
2007-002768
2011-000651
2011-000660
2011-001094
2011-001094
2011-001094
7-8
Loc.
R222
R169
R173
R95
R114
R98
R107
R281
R188
R292
R230
R63
R270
R58
R127
R227
R250
R296
R274
R147
R148
R49
R46
R47
R52
R59
R6
R62
R65
R66
R7
R71
R73
R74
R156
R194
R238
R17
R209
R239
R299
R300
R94
R97
R162
R304
R75
RA15
RA1
RA10
RA11
RA12
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
Specification
1.2Kohm,5%,1/16W,DA,TP,1608
1.5Kohm,5%,1/16W,DA,TP,1608
1.5Kohm,5%,1/16W,DA,TP,1608
1.5Kohm,5%,1/16W,DA,TP,1608
2.2Kohm,5%,1/16W,DA,TP,1608
2.2Kohm,5%,1/16W,DA,TP,1608
27Kohm,5%,1/16W,DA,TP,1608
91Kohm,5%,1/16W,DA,TP,1608
180Kohm,5%,1/16W,DA,TP,1608
330Kohm,5%,1/16W,DA,TP,1608
33Kohm,5%,1/16W,DA,TP,1608
33Kohm,5%,1/16W,DA,TP,1608
300Kohm,5%,1/16W,DA,TP,1608
1.8Kohm,1%,1/16W,DA,TP,1608
10ohm,5%,1/16W,DA,TP,1608
10ohm,5%,1/16W,DA,TP,1608
10ohm,5%,1/16W,DA,TP,1608
130Kohm,5%,1/16W,DA,TP,1608
150ohm,5%,1/16W,DA,TP,1608
24ohm,5%,1/16W,DA,TP,1608
24ohm,5%,1/16W,DA,TP,1608
3.3Kohm,1%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
39ohm,5%,1/16W,DA,TP,1608
5.1Kohm,5%,1/16W,DA,TP,1608
5.1Kohm,5%,1/16W,DA,TP,1608
5.1Kohm,5%,1/16W,DA,TP,1608
510ohm,5%,1/16W,DA,TP,1608
510ohm,5%,1/16W,DA,TP,1608
510ohm,5%,1/16W,DA,TP,1608
510ohm,5%,1/16W,DA,TP,1608
510ohm,5%,1/16W,DA,TP,1608
510ohm,5%,1/16W,DA,TP,1608
510ohm,5%,1/16W,DA,TP,1608
56ohm,5%,1/16W,DA,TP,1608
68ohm,5%,1/16W,DA,TP,1608
6.2Kohm,1%,1/16W,DA,TP,1608
10ohm,5%,63mW,L,CHIP,8P,TP
1Kohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
Samsung Electronics
Electrical Parts List
Code No.
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001094
2011-001334
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
Loc.
RA13
RA16
RA17
RA18
RA19
RA2
RA3
RA4
RA5
RA6
RA7
RA8
RA9
U28
C10
C102
C106
C108
C11
C116
C119
C122
C123
C130
C131
C135
C136
C137
C140
C145
C149
C155
C162
C165
C166
C167
C170
C171
C172
C173
C174
C175
C176
C179
C181
C185
C186
C187
C189
C190
C191
C192
Samsung Electronics
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
R-NETWORK
RC-NETWORK
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
Specification
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
39ohm,5%,63mW,L,CHIP,8P,TP
1K/5.1K/39ohm,10%,150pF,-,6V,28P
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
7-9
Electrical Parts List
Code No.
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
7-10
Loc.
C194
C195
C196
C197
C199
C203
C204
C205
C206
C207
C209
C21
C210
C211
C212
C214
C215
C216
C217
C218
C219
C22
C220
C223
C224
C227
C228
C230
C231
C232
C234
C239
C240
C241
C242
C243
C244
C245
C247
C248
C251
C252
C253
C254
C255
C257
C259
C260
C261
C262
C263
C266
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
Specification
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
Samsung Electronics
Electrical Parts List
Code No.
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
Loc.
C268
C269
C27
C271
C273
C276
C277
C28
C280
C282
C283
C284
C285
C287
C289
C29
C290
C291
C292
C293
C294
C295
C296
C297
C298
C299
C30
C302
C303
C304
C307
C309
C31
C310
C312
C313
C314
C315
C316
C317
C318
C319
C320
C321
C322
C323
C324
C326
C327
C329
C330
C332
Samsung Electronics
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
Specification
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
7-11
Electrical Parts List
Code No.
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000189
2203-000192
2203-000192
2203-000192
2203-000206
2203-000206
2203-000206
2203-000206
2203-000206
7-12
Loc.
C335
C336
C337
C338
C341
C348
C35
C38
C39
C4
C43
C44
C45
C46
C50
C51
C52
C54
C55
C56
C63
C64
C65
C66
C67
C69
C70
C71
C72
C73
C75
C76
C79
C81
C83
C85
C86
C88
C91
C92
C93
C94
C95
C96
C128
C158
C5
C101
C125
C144
C156
C47
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
Specification
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,25V,Y5V,TP,1608,
100nF,+80-20%,50V,Y5V,TP,2012,
100nF,+80-20%,50V,Y5V,TP,2012,
100nF,+80-20%,50V,Y5V,TP,2012,
100nF,10%,50V,X7R,TP,2012
100nF,10%,50V,X7R,TP,2012
100nF,10%,50V,X7R,TP,2012
100nF,10%,50V,X7R,TP,2012
100nF,10%,50V,X7R,TP,2012
Samsung Electronics
Electrical Parts List
Code No.
2203-000206
2203-000236
2203-000236
2203-000236
2203-000236
2203-000236
2203-000236
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000257
2203-000384
2203-000384
2203-000384
2203-000426
2203-000426
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
2203-000440
Loc.
C49
C184
C33
C42
C74
C80
C9
C132
C20
C208
C25
C272
C311
C328
C41
C57
C84
C126
C236
C246
C138
C139
C1
C110
C127
C147
C157
C193
C200
C201
C202
C213
C222
C229
C23
C24
C274
C278
C286
C288
C3
C300
C301
C308
C32
C331
C334
C40
C53
C58
C59
C60
Samsung Electronics
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
Specification
100nF,10%,50V,X7R,TP,2012
0.1NF,5%,50V,C0G,TP,1608
0.1NF,5%,50V,C0G,TP,1608
0.1NF,5%,50V,C0G,TP,1608
0.1NF,5%,50V,C0G,TP,1608
0.1NF,5%,50V,C0G,TP,1608
0.1NF,5%,50V,C0G,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
10nF,10%,50V,X7R,TP,1608
0.015NF,5%,50V,C0G,TP,1608
0.015NF,5%,50V,C0G,TP,1608
0.015NF,5%,50V,C0G,TP,1608
0.018NF,5%,50V,C0G,TP,1608
0.018NF,5%,50V,C0G,TP,1608
1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,1nF,10%,50V,X7R,TP,1608,-
7-13
Electrical Parts List
Code No.
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000626
2203-000681
2203-000681
2203-000681
2203-000681
2203-000681
2203-000681
2203-000783
2203-000815
2203-000815
2203-000815
2203-000815
2203-000815
2203-000815
2203-000815
2203-000815
2203-000998
2203-000998
2203-000998
2203-000998
2203-001222
2203-001408
2203-001408
2203-001408
7-14
Loc.
C104
C105
C109
C115
C117
C124
C129
C134
C163
C164
C177
C178
C182
C183
C221
C235
C249
C250
C26
C34
C342
C343
C344
C345
C346
C68
C89
C97
C99
C160
C161
C237
C238
C264
C265
C159
C15
C16
C17
C18
C188
C19
C225
C347
C12
C13
C14
C169
C103
C226
C258
C98
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
Specification
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.022NF,5%,50V,C0G,TP,1608
0.027NF,5%,50V,C0G,TP,1608
0.027NF,5%,50V,C0G,TP,1608
0.027NF,5%,50V,C0G,TP,1608
0.027NF,5%,50V,C0G,TP,1608
0.027NF,5%,50V,C0G,TP,1608
0.027NF,5%,50V,C0G,TP,1608
0.33NF,5%,50V,C0G,TP,1608
0.033NF,5%,50V,C0G,TP,1608
0.033NF,5%,50V,C0G,TP,1608
0.033NF,5%,50V,C0G,TP,1608
0.033NF,5%,50V,C0G,TP,1608
0.033NF,5%,50V,C0G,TP,1608
0.033NF,5%,50V,C0G,TP,1608
0.033NF,5%,50V,C0G,TP,1608
0.033NF,5%,50V,C0G,TP,1608
0.047NF,5%,50V,C0G,TP,1608
0.047NF,5%,50V,C0G,TP,1608
0.047NF,5%,50V,C0G,TP,1608
0.047NF,5%,50V,C0G,TP,1608
820pF,10%,50V,X7R,TP,1608,0.27nF,5%,50V,NP0,TP,1608
0.27nF,5%,50V,NP0,TP,1608
0.27nF,5%,50V,NP0,TP,1608
Samsung Electronics
Electrical Parts List
Code No.
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-002392
2203-005065
2203-005065
2401-000042
2401-000042
2401-000042
2401-000042
2401-000042
2401-000042
2401-000042
2401-000042
2401-000042
2401-000042
2401-000414
2401-000414
2401-000414
2401-000414
2401-000414
2401-000603
2401-001185
2401-001185
2401-001363
2401-002300
2401-002300
2401-002300
2401-002300
2401-002300
2401-002300
2801-000140
2801-000140
2801-003376
2801-003699
2801-003960
2804-001163
2901-001178
Loc.
C100
C107
C113
C118
C120
C121
C143
C146
C148
C151
C152
C154
C48
C6
C7
C77
C78
C8
C275
C279
C111
C112
C153
C168
C305
C339
C340
C62
C82
C87
C180
C198
C256
C325
C333
C90
C270
C306
C281
C114
C150
C2
C36
C37
C61
OSC5
OSC9
OSC1
OSC4
OSC6
OSC2
F1
Samsung Electronics
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
CRYSTAL-UNIT
CRYSTAL-UNIT
CRYSTAL-UNIT
CRYSTAL-UNIT
CRYSTAL-UNIT
OSCILLATOR-CLOCK
FILTER-EMI SMD
Specification
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
220nF,+80-20%,50V,Y5V,TP,2012
1000nF,+80-20%,10V,Y5V,TP,1608
1000nF,+80-20%,10V,Y5V,TP,1608
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
100uF,20%,16V,GP,TP,6.3x7,5
10uF,20%,16V,GP,TP,4x7,5
10uF,20%,16V,GP,TP,4x7,5
10uF,20%,16V,GP,TP,4x7,5
10uF,20%,16V,GP,TP,4x7,5
10uF,20%,16V,GP,TP,4x7,5
1uF,20%,50V,GP,TP,5x11,5
33uF,20%,35V,GP,TP,5x11,5
33uF,20%,35V,GP,TP,5x11,5
470uF,20%,16V,GP,TP,10x12.5,5
47uF,20%,50V,GP,TP,6.3x11,5
47uF,20%,50V,GP,TP,6.3x11,5
47uF,20%,50V,GP,TP,6.3x11,5
47uF,20%,50V,GP,TP,6.3x11,5
47uF,20%,50V,GP,TP,6.3x11,5
47uF,20%,50V,GP,TP,6.3x11,5
12MHz,50ppm,28-AAM,S,30ohm,12MHz,50ppm,28-AAM,S,30ohm,0.032768MHz,20ppm,28-AAY,12.5p
48MHz,50ppm,28-ABM,12pF,80ohm,
28.224MHz,50ppm,28-AAA,18pF,35ohm,BK
20MHz,50ppm,10TTL & CMOS,ST,5V
25V,2A,-,100000pF,2x1.25x1mm,TP
7-15
Electrical Parts List
Code No.
2901-001178
2901-001178
3301-000317
3301-000317
3301-000317
3301-000317
3301-000317
3301-000317
3301-000325
3301-000325
3301-000325
3301-000325
3301-000344
3301-000344
3301-000344
3301-000344
3301-001425
3301-001425
3702-000118
3708-001637
3711-000164
3711-000198
3711-000225
3711-002807
3711-002809
3711-002812
3711-002815
3711-003204
3711-003204
3711-003408
3711-003408
3711-003408
3711-003408
3711-003408
3711-003409
3711-003409
3711-003409
3711-003410
3711-003410
3711-003410
3722-001101
4301-000108
4302-000126
JB13-00002A
JC11-00004A
JC11-00005A
JC13-00014A
JC41-00186A
7-16
Loc.
F2
F3
L11
L4
L5
L6
L7
L8
L13
L14
L2
L3
BD1
BD2
BD3
BD4
L1
L10
CN12
CN3
CN22
CN14
CN24
CN20
CN27
CN2
CN18
CN4
CN5
CN13
CN16
CN21
CN25
CN6
CN1
CN19
CN23
CN17
CN26
CN7
CN11
M2
M1
U16
U53
U44
U29
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
FILTER-EMI SMD
FILTER-EMI SMD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CONNECTOR-RIBBON
CONNECTOR-FPC/FFC/PIC
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
JACK-USB
BATTERY-LI
BATTERY-NICD(2ND)
IC ASIC-UNICON
IC MASK ROM-3.3V,SOP,44P
IC MASK ROM-3.3V,SOP,44P
IC ASIC-GRAPHIC PROCESSOR
PCB-MAIN
Specification
25V,2A,-,100000pF,2x1.25x1mm,TP
25V,2A,-,100000pF,2x1.25x1mm,TP
AB,2x1.25x0.9mm,-,AB,2x1.25x0.9mm,-,AB,2x1.25x0.9mm,-,AB,2x1.25x0.9mm,-,AB,2x1.25x0.9mm,-,AB,2x1.25x0.9mm,-,AB,3.2x2.5x1.3mm,-,AB,3.2x2.5x1.3mm,-,AB,3.2x2.5x1.3mm,-,AB,3.2x2.5x1.3mm,-,AA,-,3.5x0.6x6.5mm,-,-,Mn-Zn,AA,-,3.5x0.6x6.5mm,-,-,Mn-Zn,AA,-,3.5x0.6x6.5mm,-,-,Mn-Zn,AA,-,3.5x0.6x6.5mm,-,-,Mn-Zn,AB,120ohm,3.2x1.6x1.1mm,900mA,TP,-,0.15ohm
AB,120ohm,3.2x1.6x1.1mm,900mA,TP,-,0.15ohm
36P,FEMALE,ANGLE,AU
24P,1MM,STRAIGHT,SN
1WALL,2P,1R,2.5mm,STRAIGHT,SN
1WALL,3P,1R,2.5mm,STRAIGHT,SN
1WALL,4P,1R,2.5mm,STRAIGHT,SN
BOX,6P,1R,2mm,STRAIGHT,SN
BOX,8P,1R,2mm,STRAIGHT,SN
BOX,11P,1R,2mm,STRAIGHT,SN
BOX,14P,1R,2mm,STRAIGHT,SN
BOX,24P,2R,2mm,STRAIGHT,SN
BOX,24P,2R,2mm,STRAIGHT,SN
BOX,2P,1R,2mm,STRAIGHT,SN
BOX,2P,1R,2mm,STRAIGHT,SN
BOX,2P,1R,2mm,STRAIGHT,SN
BOX,2P,1R,2mm,STRAIGHT,SN
BOX,2P,1R,2mm,STRAIGHT,SN
BOX,3P,1R,2mm,STRAIGHT,SN
BOX,3P,1R,2mm,STRAIGHT,SN
BOX,3P,1R,2mm,STRAIGHT,SN
BOX,4P,1R,2mm,STRAIGHT,SN
BOX,4P,1R,2mm,STRAIGHT,SN
BOX,4P,1R,2mm,STRAIGHT,SN
4P/1C B,8.38MM,AU,IVR,#22-28
3V,220mAH,BUTTON,20x3.2mm,NO
3.6V(1.2Vx3),60mAH,CYLINDR,-,3
MJC-1300G,UNICON,QFP,44P,K3P5V1000D-GC,HIGH,ML-9400W,16M(1MX16),
K3P5V1000D-GC,LOW,ML-9400W,16M(1MX16),
SPGPM,ML-1650 VE,256PIN/256+16PIN,3.3V,F668
SCX-5315F,FR-4,4L,V1.0,1.6T,235 X 215MM,-,-,-,-
Samsung Electronics
Electrical Parts List
7-2 LIU B’d
Code No.
Loc.
No.
JC92-01355A
LIU PBA
1
PBA SUB-LIU
Description
SCX-5100,XEROX,USA,LIU,FAX
Specification
0401-000005
D3
1
DIODE-SWITCHING
1N4148,100V,200MA,DO-35,TP
0401-000148
D4
1
DIODE-SWITCHING
1N914,100V,500mA,DO-35,TP
0401-000148
D5
1
DIODE-SWITCHING
1N914,100V,500mA,DO-35,TP
0401-000148
D6
1
DIODE-SWITCHING
1N914,100V,500mA,DO-35,TP
0401-000148
D7
1
DIODE-SWITCHING
1N914,100V,500mA,DO-35,TP
0401-000148
D8
1
DIODE-SWITCHING
1N914,100V,500mA,DO-35,TP
0401-000148
D9
1
DIODE-SWITCHING
1N914,100V,500mA,DO-35,TP
0402-000338
BD1
1
DIODE-BRIDGE
W06F,600V,1.5A,-,BK
0403-000153
ZD1
1
DIODE-ZENER
1N4746A,18V,5%,1W,DO-41,TP
0403-000153
ZD2
1
DIODE-ZENER
1N4746A,18V,5%,1W,DO-41,TP
0403-000716
ZD3
1
DIODE-ZENER
MTZJ4.7B,4.7V,4.55-4.8V,500mW,
0403-000716
ZD4
1
DIODE-ZENER
MTZJ4.7B,4.7V,4.55-4.8V,500mW,
0403-000716
ZD5
1
DIODE-ZENER
MTZJ4.7B,4.7V,4.55-4.8V,500mW,
0403-000716
ZD6
1
DIODE-ZENER
MTZJ4.7B,4.7V,4.55-4.8V,500mW,
0501-000398
Q6
1
TR-SMALL SIGNAL
KSC945,NPN,250mW,TO-92,TP,120-
0502-000133
Q2
1
TR-POWER
2SA1156,PNP,1W,TO-126,-,40-80
0505-000335
Q1
1
FET-SILICON
VN2410M,N,240V,0.19A,10ohm,7.9
0604-000118
U2
1
PHOTO-COUPLER
TR,20-300%,200mW,DIP-4,ST
0604-000118
U9
1
PHOTO-COUPLER
TR,20-300%,200mW,DIP-4,ST
0604-000142
U11
1
PHOTO-COUPLER
TR,-,200mW,DIP-4,ST
1405-000144
VAR3
1
VARISTOR
430V,1250A,14x7.2mm,TP
1405-000144
VAR5
1
VARISTOR
430V,1250A,14x7.2mm,TP
1405-000170
VAR1
1
VARISTOR
82V,1200A,9x4.1mm,TP
1405-000226
VAR2
1
VARISTOR
-,25A,5mm,TP
2001-000034
R44
1
R-CARBON
220OHM,5%,1/4W,AA,TP,2.4X6.4MM
2001-000065
R45
1
R-CARBON
10KOHM,5%,1/4W,AA,TP,2.4X6.4MM
2001-000070
R16
1
R-CARBON
15KOHM,5%,1/4W,AA,TP,2.4X6.4MM
2001-000084
R1
1
R-CARBON
100KOHM,5%,1/4W,AA,TP,2.4X6.4MM
2001-000435
R2
1
R-CARBON
1MOHM,5%,1/8W,AA,TP,1.8X3.2MM
2001-000631
R7
1
R-CARBON
30KOHM,5%,1/4W,AA,TP,2.4X6.4MM
2001-000923
R52
1
R-CARBON
680ohm,5%,1/8W,AA,TP,1.8x3.2mm
2001-001004
R4
1
R-CARBON
82OHM,5%,1/4W,AA,TP,2.4X6.4MM
2001-001004
R5
1
R-CARBON
82OHM,5%,1/4W,AA,TP,2.4X6.4MM
2003-000178
R3
1
R-METAL OXIDE
15Kohm,5%,1W,AA,TP,4.3x12mm
2003-000659
R20
1
R-METAL OXIDE(S)
33ohm,5%,1W,AA,TP,3.3x9mm
2004-000284
R15
1
R-METAL
12Kohm,1%,1/4W,AA,TP,2.4x6.4mm
2004-000432
R51
1
R-METAL
1Kohm,1%,1/4W,AA,TP,2.4x6.4mm
2004-000496
R49
1
R-METAL
2.74Kohm,1%,1/4W,AA,TP,2.4x6.4
2004-002234
R48
1
R-METAL
560ohm,1%,1/4W,AA,TP,2.4x6.4mm
2201-000119
C10
1
C-CERAMIC,DISC
100NF,+80-20%,50V,Y5V,TP,8X3MM,5
2201-000119
C11
1
C-CERAMIC,DISC
100NF,+80-20%,50V,Y5V,TP,8X3MM,5
2301-001308
C16
1
C-FILM,MPEF
15NF,10%,400V,BK,10.5X4X9MM,7.5
2301-001308
C9
1
C-FILM,MPEF
15NF,10%,400V,BK,10.5X4X9MM,7.5
2305-000566
C5
1
C-FILM,MPEF
1uF,10%,250V,BK,25.5x9x16.5mm,
2401-000026
C14
1
C-AL
3.3UF,20%,50V,GP,TP,5X11,5
2401-000480
C12
1
C-AL
10uF,20%,50V,GP,TP,5x11,5
2401-000480
C13
1
C-AL
10uF,20%,50V,GP,TP,5x11,5
Samsung Electronics
7-17
Electrical Parts List
Code No.
Loc.
No.
2401-000962
C3
1
Description
C-AL
Specification
22uF,20%,50V,GP,TP,5x11,5
2401-001775
C4
1
C-AL
470nF,20%,50V,GP,TP,4x7,5
3501-001160
CML_1
1
RELAY-MINIATURE
12VDC,200MW,2000MA,-,4MS,4MS
3711-002815
CN1
1
CONNECTOR-HEADER
BOX,14P,1R,2mm,STRAIGHT,SN
3722-000255
CN3
1
JACK-MODULAR
6P/4C,INVERTED,N,ANGLE,STANDARD,N,IVR,AU30U
3722-000574
CN2
1
JACK-MODULAR
6P/6C,INVERTED,N,ANGLE,STANDARD,N,BLK,AU
4715-001043
ARS2
1
SURGE ABSORBER
600V,20%,500A,-,TP
JB26-00001A
T1
1
TRANS MATCHING-REMOTE
SF-3100,-,30KOHM:30KOHM
JC39-40511A
J1
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
J2
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP10
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP12
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP13
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP18
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP2
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP3
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP4
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP5
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP6
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP7
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP8
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
JP9
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
R47
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC39-40511A
R54
1
CBF HARNESS
ML-80,JUMPER,AWG22,52mm,SILVER
JC41-00127B
PCB
1
PCB-LIU(XRH)
SCX-5100(XRH),FR-1,1L,V1.4,1.6T,
JC68-00573A
ASS'Y LABEL
1
LABEL(R)-BARCODE
ML-4500,PET,T0.05,10mm,20mm,-,WHT,-,-,-
JC68-00573A
LABEL_BARCODE
1
LABEL(R)-BARCODE
ML-4500,PET,T0.05,10mm,20mm,-,WHT,-,-,-
JF26-10052A
L7
1
TRANS PULSE
SF50,500V,10MOHM
JG26-50001A
T2
1
TRANS MATCHING
SF6000,-,600/600
7-18
Samsung Electronics
Electrical Parts List
7-3 OPE B’d
Code No.
Loc.
No.
JC92-01380A
OPE PBA
1
PBA SUB-OPE(XEROX)
SCX-5100,XEROX,USA,OPE,
0401-000116
D1
1
DIODE-SWITCHING
MMSD914T1,100V,200mA,SOD-123,TP
0401-000116
D2
1
DIODE-SWITCHING
MMSD914T1,100V,200mA,SOD-123,TP
0401-000116
D3
1
DIODE-SWITCHING
MMSD914T1,100V,200mA,SOD-123,TP
0401-000116
D4
1
DIODE-SWITCHING
MMSD914T1,100V,200mA,SOD-123,TP
0401-000116
D5
1
DIODE-SWITCHING
MMSD914T1,100V,200mA,SOD-123,TP
0501-000279
Q1
1
TR-SMALL SIGNAL
KSA1182-Y,PNP,150mW,SOT-23,TP,
0601-001404
LED1
1
LED
CHIP,RED,2.0mm,660mm
0801-001090
U2
1
IC-CMOS LOGIC
74HC14,SCHIMITT INVERTER,SOP,1
2007-000033
J1
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J10
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J11
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J12
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J15
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J16
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J2
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J3
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J6
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J8
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J87
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J88
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J89
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J9
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J90
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000033
J91
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000074
R44
1
R-CHIP
100ohm,5%,1/16W,DA,TP,1608
2007-000074
R45
1
R-CHIP
100ohm,5%,1/16W,DA,TP,1608
2007-000078
R42
1
R-CHIP
1Kohm,5%,1/16W,DA,TP,1608
2007-000090
R12
1
R-CHIP
10KOHM,5%,1/16W,DA,TP,1608
2007-000094
R1
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R11
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R2
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R26
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R27
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R28
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R29
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R30
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R31
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R32
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000094
R33
1
R-CHIP
22Kohm,5%,1/16W,DA,TP,1608
2007-000120
R14
1
R-CHIP
680ohm,5%,1/16W,DA,TP,1608
2007-000539
R43
1
R-CHIP
200ohm,5%,1/16W,DA,TP,1608
2203-000189
C14
1
C-CERAMIC,CHIP
100nF,+80-20%,25V,Y5V,TP,1608,
2203-000189
C16
1
C-CERAMIC,CHIP
100nF,+80-20%,25V,Y5V,TP,1608,
2203-000189
C2
1
C-CERAMIC,CHIP
100nF,+80-20%,25V,Y5V,TP,1608,
2203-000189
C3
1
C-CERAMIC,CHIP
100nF,+80-20%,25V,Y5V,TP,1608,
2203-000236
C9
1
C-CERAMIC,CHIP
0.1NF,5%,50V,C0G,TP,1608
2203-000626
C6
1
C-CERAMIC,CHIP
0.022NF,5%,50V,C0G,TP,1608
Samsung Electronics
Description
Specification
7-19
Electrical Parts List
Code No.
Loc.
No.
2203-000626
C7
1
C-CERAMIC,CHIP
0.022NF,5%,50V,C0G,TP,1608
2203-000626
C8
1
C-CERAMIC,CHIP
0.022NF,5%,50V,C0G,TP,1608
2203-000998
C12
1
C-CERAMIC,CHIP
0.047NF,5%,50V,C0G,TP,1608
2203-000998
C13
1
C-CERAMIC,CHIP
0.047NF,5%,50V,C0G,TP,1608
2402-000176
C1
1
C-AL,SMD
10uF,20%,16V,GP,TP,4.3x4.3x5.4
2404-000284
C15
1
C-TA,CHIP
10uF,20%,16V,-,TP,3528,-
2802-001069
OSC1
1
RESONATOR-CERAMIC
7.37MHz,0.5%,TP,4.7x4.1x1.7
3711-003411
CN2
1
CONNECTOR-HEADER
BOX,5P,1R,2mm,STRAIGHT,SN
JB13-00004A
U1
1
IC ASIC-OPE
SF-3100,HT48C5,SSOP,48P,16.18X10.67X2.79
JC39-00230A
LCD HARNESS
1
CBF HARNESS-LCD
SCX-5312,WIRE,UL2877,14,50,BLACK/WHIT
JC41-00126A
OPE PCB(XEROX)
1
PCB-OPE(XEROX)
SCX-5100,FR-1,1L,V1.0,1.6T,326 X 170MM,-,X2,-,-
JG07-20001A
LCD
1
LCD
SF4000,UC-162937-TNAR5-A,BLK/G
7-20
Description
Specification
Samsung Electronics
Electrical Parts List
7-4 ADF B’d
Code No.
Loc.
No.
JC92-01382A
ADF PBA
1
PBA SUB-ADF
SCX-5100,XEROX,USA,ADF,
0407-000101
D1
1
DIODE-ARRAY
DA204K,20V,100mA,C2-3,SOT-23,T
0407-000101
D2
1
DIODE-ARRAY
DA204K,20V,100mA,C2-3,SOT-23,T
0604-001154
U4
1
PHOTO-INTERRUPTER
TR,0.2-1.0MA,80MW,DIP,ST
0801-000945
U3
1
IC-CMOS LOGIC
74HC244,BUFFER/DRIVER,SOP,20P,
1003-001102
U5
1
IC-MOTOR DRIVER
TEA3718DP,DIP,16P,300MIL,SINGL
1003-001102
U6
1
IC-MOTOR DRIVER
TEA3718DP,DIP,16P,300MIL,SINGL
2005-000419
R2
1
R-WIRE WOUND,NON
0.33ohm,1%,1W,AA,TP,4.3x12mm
2005-000419
R27
1
R-WIRE WOUND,NON
0.33ohm,1%,1W,AA,TP,4.3x12mm
2007-000033
R30
1
R-CHIP
0OHM,5%,1/8W,DA,TP,3216
2007-000070
R31
1
R-CHIP
0ohm,5%,1/16W,DA,TP,1608
2007-000070
R32
1
R-CHIP
0ohm,5%,1/16W,DA,TP,1608
2007-000078
R29
1
R-CHIP
1Kohm,5%,1/16W,DA,TP,1608
2007-000078
R5
1
R-CHIP
1Kohm,5%,1/16W,DA,TP,1608
2007-000080
R15
1
R-CHIP
2Kohm,5%,1/16W,DA,TP,1608
2007-000090
R20
1
R-CHIP
10KOHM,5%,1/16W,DA,TP,1608
2007-000090
R9
1
R-CHIP
10KOHM,5%,1/16W,DA,TP,1608
2007-000098
R28
1
R-CHIP
56Kohm,5%,1/16W,DA,TP,1608
2007-000098
R6
1
R-CHIP
56Kohm,5%,1/16W,DA,TP,1608
2007-000113
R21
1
R-CHIP
33ohm,5%,1/16W,DA,TP,1608
2007-000113
R22
1
R-CHIP
33ohm,5%,1/16W,DA,TP,1608
2007-000113
R23
1
R-CHIP
33ohm,5%,1/16W,DA,TP,1608
2007-000113
R24
1
R-CHIP
33ohm,5%,1/16W,DA,TP,1608
2007-000113
R25
1
R-CHIP
33ohm,5%,1/16W,DA,TP,1608
2007-000113
R26
1
R-CHIP
33ohm,5%,1/16W,DA,TP,1608
2007-000402
R19
1
R-CHIP
150ohm,5%,1/16W,DA,TP,1608
2203-000189
C16
1
C-CERAMIC,CHIP
100nF,+80-20%,25V,Y5V,TP,1608,
2203-000189
C17
1
C-CERAMIC,CHIP
100nF,+80-20%,25V,Y5V,TP,1608,
2203-000189
C18
1
C-CERAMIC,CHIP
100nF,+80-20%,25V,Y5V,TP,1608,
2203-000189
C8
1
C-CERAMIC,CHIP
100nF,+80-20%,25V,Y5V,TP,1608,
2203-000626
C19
1
C-CERAMIC,CHIP
0.022NF,5%,50V,C0G,TP,1608
2203-000626
C2
1
C-CERAMIC,CHIP
0.022NF,5%,50V,C0G,TP,1608
2203-001222
C12
1
C-CERAMIC,CHIP
820pF,10%,50V,X7R,TP,1608,-
2203-001222
C13
1
C-CERAMIC,CHIP
820pF,10%,50V,X7R,TP,1608,-
2203-001222
C5
1
C-CERAMIC,CHIP
820pF,10%,50V,X7R,TP,1608,-
2203-001222
C6
1
C-CERAMIC,CHIP
820pF,10%,50V,X7R,TP,1608,-
2203-001801
C14
1
C-CERAMIC,CHIP
10nF,10%,100V,X7R,TP,2012
2203-001801
C15
1
C-CERAMIC,CHIP
10nF,10%,100V,X7R,TP,2012
2203-001801
C9
1
C-CERAMIC,CHIP
10nF,10%,100V,X7R,TP,2012
2401-000042
C10
1
C-AL
100uF,20%,16V,GP,TP,6.3x7,5
2401-002300
C11
1
C-AL
47uF,20%,50V,GP,TP,6.3x11,5
3301-000325
L3
1
CORE-FERRITE BEAD
AB,3.2x2.5x1.3mm,-,-
Samsung Electronics
Description
Specification
7-21
Electrical Parts List
Code No.
Loc.
No.
3301-000325
L4
1
CORE-FERRITE BEAD
AB,3.2x2.5x1.3mm,-,-
3301-000325
L6
1
CORE-FERRITE BEAD
AB,3.2x2.5x1.3mm,-,-
3301-000325
L7
1
CORE-FERRITE BEAD
AB,3.2x2.5x1.3mm,-,-
3301-001425
L5
1
CORE-FERRITE BEAD
AB,120ohm,3.2x1.6x1.1mm,900mA,TP,-,0.15ohm
3711-003340
CN2
1
CONNECTOR-HEADER
BOX,16P,2R,2mm,STRAIGHT,SN
3711-003409
CN4
1
CONNECTOR-HEADER
BOX,3P,1R,2mm,STRAIGHT,SN
3711-003410
CN1
1
CONNECTOR-HEADER
BOX,4P,1R,2mm,STRAIGHT,SN
3711-003411
CN3
1
CONNECTOR-HEADER
BOX,5P,1R,2mm,STRAIGHT,SN
JC41-00129A
ADF PCB
1
PCB-ADF
SCX-5100,FR-4,2L,V1.0,1.6T
JC62-00002A
U5(HEAT-SINK)
1
HEAT SINK-(4500)
ML-4500,BRONZE,0.5,9.3,38,-,-,-
JC62-00002A
U6(HEAT-SINK)
1
HEAT SINK-(4500)
ML-4500,BRONZE,0.5,9.3,38,-,-,-
7-22
Description
Specification
Samsung Electronics
Block Diagrams
8. Block Diagrams
2P
PC N T
DEV CN T
4P
MOTOR
DRIVER
H
SUPPLY
V
V
BLADE
2 2P
CN 1
DEV MOTOR
8P
FEED MOTOR
11P
LSU
2P
THERMISTOR
3P
FAN1
3P
FAN1
3P
CN 1 3 CN 5
4P
USB CABLE
MAIN PBA
1 0P
CN 2 2
CN 2 0 CN 2 7 CN 3 0
CN 28 CN 3
CN 24
CN 2 3 CN 2 1 CN 2 6 CN 2 9
2P
OPC
ADF
H
+5V/+24V/+12V/+24Vs /Fuser
CN 1 8
4P
CN 1 9 CN 1 7
HYPER
CN 1 2 CN 1 9 CN 2 5
4P
CN 3 1
8P
SCF
16MB
C N15(10 0P)
2 4P
CN 1 4 CN 3 3 CN 4 CN 7 C N1 0 CN 1 1
SDRAM DIMM
OU T BIN F ULL
Option
CN 1 6
36 P
15P D -SUB
FLAT MOTOR
Fl as h DIMM
PS3 (2MB)
CN15(100P)
Network CARD
CENTRONICS
CABLE
D-SUB
CONN.
DEV
SMPS / HVPS
CN 2
CN8
MI COM
- LCD Drive
- Key Scan
CN6
OPE
Plat en
M
SCA N
L CD 20x2line
5P
T
DEV_ID
3P
TONER_T X
4P
TONER_RX
2P
PTL
4P
COVER OPEN
S/W
+24V / +5V
DADF MOTOR
10P
PAPER SENSOR
POS,DET
3P x 2EA
CCD MODULE
External
Auditron
3P
3P
TRANSFORMER
6P
600/ / 600
2P
2P
14P
2P
Tx: Rx
LIN E
SOLENOID
PICK_ UP,DUPL EX,MP
PAPER
SEN SOR
IN T ERFAC E
MODEM
EXT_PHONE
SEPRATING
PART
EXTERNAL
PHONE
INTERFACE
PART
LI U
LINE1
EXTERNAL
PHONE
FEED+P.EMP,EXIT,MP
8-1
Block Diagrams
8-2
Connection Diagrams
9. Connection Diagrams
MAIN
LCD 16x2line
M
DEV
H
H
SUPPLY
V
V
BLADE
SPGPm
Backup logic
OPE
MICOM
- LCD Drive
- Key Scan
SMPS / HVPS
ARM946ES
2 4P
SRAM
CACHE(16K*2)
ROMC
(1MB) X 2EA
SDRAM,16MB
PLATEN
15P D-SUB
D-SUB
CONN.
24P
+5V/+24V/+12V/+24Vs/Fuser
SDRAMC
Flash,Kernel
5P
Option
SDRAM
DIMM
DMAC
MOTOR
DRIVER
PVC
A3977SLR
11P
I/O I/F
2P
Engine Control
3P
IEEE1284/USB2.0
LSU
THERMISTOR
FAN
3P
Extended
DEV_ID
3P
GPIO
Option
TONER_TX
4P
TONER_RX
2P
PTL
74LCX245
NETWORK KIT
NETWORK
I/F(NetONE)
ADF
MOTOR 1
MOTOR 2
8P
GEU/HCT/gCODEC
16MB
FLAT MOTOR
SOLENOID
2P x 3EA
74HCT273
PICK_UP,DUPLEX,MP
3P x 2EA
6P x 1EA
PAPER SENSOR
CIP4
MOTOR
DRIVER
FEED+P.EMP,EXIT,MP
4P
Image Processer
ADF MOTOR
FAST
SRAM
PAPER SENSOR
POS,DET
T
AFE I/F
+24V / +5V
Option
MODEM
I/O PORT
(1Mb it)
3P x 2EA
33.6Kbps
Motor CNTR
MOTOR
DRIVER
COVER OPEN S/W
1
4P
TRANSFORMER
600//600
Tx:Rx
DMAC
AFE
LIN E
IN T ERF A CE
Network I/F
CENTRONICS CABLE
Option
2 2P
CCD MODULE
MODEM &
EXT_PHONE
SEPERATING
PART
EXTERNAL
PHONE
INTERFACE
PART
LIU
LINE1
EXTERNAL
PHONE
External
Auditron
USB CABLE
9-1
Connection Diagrams
9-2
Connection Diagrams
10. Schematic Diagrams
10-1 Main Circuit Diagram (1/16)
10-1
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (2/16)
10-2
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (3/16)
10-3
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (4/16)
10-4
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (5/16)
10-5
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (6/16)
10-6
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (7/16)
10-7
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (8/16)
10-8
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (9/16)
10-9
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (10/16)
10-10
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (11/16)
10-11
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (12/16)
10-12
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (13/16)
10-13
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (14/16)
10-14
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (15/16)
10-15
- This Document can not be used without Samsung's authorization -
Connection Diagrams
Main Circuit Diagram (16/16)
10-16
- This Document can not be used without Samsung's authorization -
Connection Diagrams
10-2 LIU Circuit Diagram
*
1K, 2W
*
10, 1%,0.25W
*
*
*
*
*: for EU PTT
ARS1-3 : OPTION
0.25W
(BLK)
*
*
180K, 1/4W
*
/250V
*
(BRW)
120K
*
1K,1%
/250V
2.74K, 1%
(RED)
*
600
*
*
(ORG)
0.22UF/16V
/16V
/16V
*
600:600
*
*
,1W
*
(BLU)
*
(YEL)
(GRN)
15nF/400V
10-17
- This Document can not be used without Samsung's authorization -
Connection Diagrams
10-3 OPE Circuit Diagram
10-18
- This Document can not be used without Samsung's authorization -
Connection Diagrams
10-4 HVPS Circuit Diagram (1/2)
5V
18V
R403
62KF
Q401
A708-Y
MHV-PWM
3
CON03-#22
24VS
T401
KAB-006
R405
150KF
R412
2.2K
R419
5.6K
R407
85KF
C402
104
R401
100
R404
33K
3
+
2
-
4
U103-B
7407
U101-A
KA324
D404
1N4148
R402
56KF
R411
2K
C407
104
C401
222
MHV
50K
1
Q402
D526-Y
7
5
2
6
R501
100
1
R406
16.2KF
D401
1N4148
C403
333
OPC
R410
1W 3
R508
47K
C503
104
R506
86.6KF
CON03-#24
2
U103-A
7407
R505
27K
R519
2.2K
R503
100KF
R504
86.6KF
R502
2K
DEV
50K
24VS
ZD401
1W 150V
T501
T1167
Q502
D526-Y
-
5
+
R507
12KF
D502
4KV
1
7
5
2
6
R514
MGR1/2W 50K
BLADE
C505
2KV 680
C506
3KV 471
R515
MGR1/2W 50K
SUPPLY
7
D501
1N4148
4
R509
47K
R510
430
ZD502
150V
R512
MGR1/2W 12MF
C504
333
DEV
R516
MGR1/2W 50K
R511
1W 3
R517
MGR1/2W 15MF
U102
KA7818
IN
OUT
18V
+
GND
C102
104
6
U101-B
KA324
C501
104
C502
222
R416
MGR1/2W 30MF
R413
MGR1/2W 12MF
4
Q501
A708-Y
BIAS-PWM
C406
3KV 471
D402
4KV
R409
430
18V
R520
5.6K
R418
MGR1/2W 100KF
MHV
C405
2KV 680
R408
47K
24VS
5V
D403
4KV
C404
3KV 471
1
C103
104
DONGYANG INSTRUMENTS
C104
35V 47uF
TITLE
H.V.P.S
DESIGNED CHECKED APPROVED DRW. NO MCKINLEY-HVPS
REF. NO
JC44-00017A
SIZE A4
DATE 01/05/20
REV.
1.0
J.S.YOUN
1 OF 2
10-19
- This Document can not be used without Samsung's authorization -
Connection Diagrams
HVPS Circuit Diagram (2/2)
5V
18V
R403
62KF
Q401
A708-Y
MHV-PWM
3
CON03-#22
24VS
T401
KAB-006
R405
150KF
R412
2.2K
R419
5.6K
R407
85KF
C402
104
R401
100
R404
33K
3
+
2
-
4
U103-B
7407
U101-A
KA324
D404
1N4148
R402
56KF
R411
2K
C407
104
C401
222
MHV
50K
1
Q402
D526-Y
7
5
2
6
R501
100
1
R406
16.2KF
D401
1N4148
C403
333
OPC
R410
1W 3
R508
47K
C503
104
R506
86.6KF
CON03-#24
2
U103-A
7407
R505
27K
R519
2.2K
R503
100KF
R504
86.6KF
R502
2K
DEV
50K
24VS
ZD401
1W 150V
T501
T1167
Q502
D526-Y
-
5
+
R507
12KF
D502
4KV
1
7
5
2
6
R514
MGR1/2W 50K
BLADE
C505
2KV 680
C506
3KV 471
R515
MGR1/2W 50K
SUPPLY
7
D501
1N4148
4
R509
47K
R510
430
ZD502
150V
R512
MGR1/2W 12MF
C504
333
DEV
R516
MGR1/2W 50K
R511
1W 3
R517
MGR1/2W 15MF
U102
KA7818
IN
OUT
18V
+
GND
C102
104
6
U101-B
KA324
C501
104
C502
222
R416
MGR1/2W 30MF
R413
MGR1/2W 12MF
4
Q501
A708-Y
BIAS-PWM
C406
3KV 471
D402
4KV
R409
430
18V
R520
5.6K
R418
MGR1/2W 100KF
MHV
C405
2KV 680
R408
47K
24VS
5V
D403
4KV
C404
3KV 471
1
C103
104
DONGYANG INSTRUMENTS
C104
35V 47uF
TITLE
DESIGNED CHECKED APPROVED DRW. NO
H.V.P.S
MCKINLEY-HVPS
REF. NO
JC44-00017A
SIZE A4
DATE 01/05/20
REV.
1.0
J.S.YOUN
10-20
- This Document can not be used without Samsung's authorization -
1 OF 2
Connection Diagrams
10-5 SMPS Circuit Diagram (110V)
C4
C-CX104224
F1
C2
C6
TNR2
125V8A
LF1 C-CX104224C-CY222
TNR-14V182K
F2
125V5A
LF2
BD1
D3SB60
C7
C-CX104224
C29
35V1000uF
+24V
2
TH1
15D-9
9
8
10
7
24V
L2/A
C41
ACINPUT/N
1
ACINPUT/L
AC INPUT
85V-135Vac
C27
13
D5/B
TNR1
INR14D561K
R1
1W560KJ
R3
1W100KJ
C10
200V820uF
C22
D5/A
D10LC20U
R41 R42 R43
C30
35V1000uF1W1.2KJ
24VG
R4
2W100KJ
C-CY222
C5
C-CY222
GND
R5
2W100KJ
C11
R6
1W100KJ
C-MYN630V103
L1
2
C24
35V100uF
R23
1/4W100J
C18
630V333K
12
ZD4
CON2
1
D2
D1NL20U
R11
SY1
BTA12-600B
R17
1/8W51J
IC3
IC-278RXX
C25
35V100uF
6
9
4
D6
D1NL20U
IN
GND
D1
BYV-26E
3
1
OUT
12V
L2/B
D7
D1NL20U
11
C28
C-MY50V104
C42
1KV471
1/8W470J
Q2
C1008
2
C43
12VG
L2/C
VCC
CT
RT
6
5
5V
C-MY50V472J
C12
35V33uF
7
R15
1/8W680J
C34
10V3300uF
F3
SB560
16
CS 6
FB
R9
1/8W22KJ
GND
Q2
IS
R24
1W47J
3
C17
50V104J
OUT
15
4
5
R37
1/8W120J
D9/A
IC2
7653
Q3
PC3
S21ME4FY
R22
1W180J
R14
1/8W24J
2
R12
R13
1/6W2.2J 1/8W1KJ
2
C1
1
C13
D8/B
SB560
R31
1/8W120J
R2
1W47J
C26
C-MY50V104
R11
R10
1W0.35J
R66
RD1/8W01.5KJ
+24S
C14
R16
50V102J 1/8W680J
R18
C15
1/8W18KJ 50V471J
R19
1/8W5.6KJ
C16
50V683J
PT1 EER3435
C33
10V3300uF
5VG
+24V ZD1
ZD-500MW30V ZD-500MW6.2V
ZD2
R25
1/8W10KJ
R20
R32
1/8W1KJ
R31
1/8W1KJ
RV1
FUSER_ON
PC1
PC-123
C21
R27
1/8W68J
Q4
C1008
R26
1/8W220J
R28
1/8W680J
PC2
PC-123
C19
R30
1/8W220J
C20
C-MY50V104
R34
1.2KJ
1uF
IC1
431
R35
1KJ
C-MY50V104
10-21
- This Document can not be used without Samsung's authorization -
Connection Diagrams
SMPS Circuit Diagram (220V)
C4
C-CX104224
F1
C2
C6
TNR2
125V8A
LF1 C-CX104224C-CY222
TNR-14V182K
F2
250V3.15A
LF2
BD1
D3SB60
C7
C-CX104224
C29
35V1000uF
+24V
2
TH1
15D-9
9
8
10
7
24V
L2/A
C41
ACINPUT/N
1
ACINPUT/L
AC INPUT
85V-135Vac
13
D5/B
TNR1
INR14D561K
R1
1W560KJ
R3
1W130V(ZEN)
C10
400V330uF
C22
D5/A
D10LC20U
R41 R42 R43
C30
35V1000uF1W1.2KJ
24VG
R4
2W100KJ
C-CY222
C5
C-CY222
GND
R5
2W100KJ
C11
R6
1W220KJ
C-MYN630V103
L1
2
C24
35V100uF
R23
1/4W100J
C18
630V333K
12
ZD4
CON2
1
D2
D1NL20U
R11
SY1
BTA12-600B
R17
1/8W51J
IC3
IC-278RXX
C25
35V100uF
6
9
4
D6
D1NL20U
IN
GND
D1
BYV-26E
3
1
OUT
12V
L2/B
D7
D1NL20U
11
C28
C-MY50V104
C42
1KV471
1/8W470J
Q2
C1008
2
C43
12VG
L2/C
R15
1/8W680J
VCC
6
5
16
F3
5V
C-MY50V472J
C12
35V33uF
CT
RT
C34
10V3300uF
SB560
CS 6
FB
GND
R9
1/8W22KJ
Q2
IS
R24
1W47J
OUT
15
7
C17
50V104J
IC2
7653
4
5
3
R22
1W180J
R14
1/8W24J
Q3
PC3
S21ME4FY
R37
1/8W120J
D9/A
2
R12
R13
1/6W2.2J 1/8W1KJ
2
C1
1
C13
D8/B
SB560
R31
1/8W120J
R2
1W47J
C26
C-MY50V104
R11
R10
1W1J
R66
RD1/8W01.5KJ
+24S
C14
R16
50V102J 1/8W680J
R18
C15
1/8W18KJ 50V471J
R19
1/8W5.6KJ
C16
50V683J
PT1 EER3435
C33
10V3300uF
5VG
+24V ZD1
ZD-500MW30V ZD-500MW6.2V
ZD2
R25
1/8W10KJ
R20
R32
1/8W1KJ
R31
1/8W1KJ
RV1
FUSER_ON
PC1
PC-123
C21
R27
1/8W68J
Q4
C1008
R26
1/8W220J
R28
1/8W680J
PC2
PC-123
10-22
- This Document can not be used without Samsung's authorization -
C19
R30
1/8W220J
C20
C-MY50V104
C-MY50V104
R34
1.2KJ
1uF
IC1
431
R35
1KJ
Connection Diagrams
10-6 ADF Circuit Diagram
10-23
- This Document can not be used without Samsung's authorization -
Connection Diagrams
10-7 Flat Circuit Diagram
10-24
- This Document can not be used without Samsung's authorization -
Connection Diagrams
10-8 PTL Circuit Diagram
10-25
- This Document can not be used without Samsung's authorization -
Connection Diagrams
10-9 Sensor Circuit Diagram
10-26
- This Document can not be used without Samsung's authorization -
Connection Diagrams
10-10 Toner_Rx Circuit Diagram
10-27
- This Document can not be used without Samsung's authorization -
Connection Diagrams
10-11 Toner_Tx Circuit Diagram
10-28
- This Document can not be used without Samsung's authorization -