Apple AppleVision monitors User`s manual

Add to my manuals
112 Pages

advertisement

Apple AppleVision monitors User`s manual | Manualzz
1
Setting Up Your Monitor
The AppleVision 850 and AppleVision 850AV are two-page, Trinitron® color
monitors with a diagonal viewable image size of 19.0 inches. Both monitors
support a variety of resolutions and feature advanced controls for accurate
color rendering. The monitors work with Mac OS–based and Windows-based
computers. The AppleVision 850AV includes an integrated audio system
consisting of built-in speakers and microphone.
This chapter reviews important safety information and explains how to set up
and connect your monitor to your computer. If you purchased a new
computer along with your monitor, refer to the setup instructions that came
with your computer in addition to the instructions in this manual.
Important safety and cleaning instructions
WARNING Do not clean your monitor screen with a cleaner that contains
alcohol or acetone. You might damage the screen. For more information
about cleaning your monitor, see “Care and Cleaning” in Chapter 5.
1
For your own safety and that of your equipment, always take the
following precautions.
Disconnect the monitor’s power plug (by pulling the plug, not the cord) if any
of the following conditions exists:
m the power cord or plug becomes frayed or otherwise damaged
m you spill something into the case
m your monitor is exposed to rain or any other excess moisture
m your monitor has been dropped or the case has been otherwise damaged
m you suspect that your monitor needs service or repair
m you want to clean the case (use only the recommended procedure
described in “Care and Cleaning” in Chapter 5)
IMPORTANT The only way to disconnect power completely is to unplug the
monitor’s power cord. Make sure at least one end of the power cord is within
easy reach so that you can unplug the monitor when you need to.
Be sure that you always:
m Keep your monitor away from sources of liquids, such as washbasins,
bathtubs, shower stalls, beverages, and so on.
m Avoid setting anything on top of the monitor (such as a book or cup). The
monitor could overheat and be damaged.
m Keep the monitor’s vents free from obstruction.
m Protect your monitor from dampness or wet weather, such as rain, snow,
and so on.
m Read all the installation instructions carefully before you plug your
monitor into a power source.
m Keep these instructions handy for reference by you and others.
m Follow all instructions and warnings dealing with your system.
WARNING Never remove the cover from the monitor or you may come in
contact with hazardous voltage levels capable of causing serious injury
and possibly death.
2
Chapter 1
WARNING Electrical equipment may be hazardous if misused. Operation
of this product, or similar products, must always be supervised by an
adult. Do not allow children access to the interior of any electrical
product, and do not permit them to handle any cables.
What about electromagnetic emissions?
There has been recent public discussion of the possible health effects of
prolonged exposure to extremely low frequency (ELF) and very low
frequency (VLF) electromagnetic fields. Such fields are associated with
electromagnetic sources such as television sets, electrical wiring, and some
household appliances—as well as computer monitors.
Apple has reviewed scientific reports and sought the counsel of government
regulatory agencies and respected health organizations. Based on the
prevailing evidence and opinions, Apple believes that the electric and
magnetic fields produced by computer monitors do not pose a health risk.
In response to those customers who wish to reduce their exposure to
electromagnetic fields, Apple has lowered the emission levels of Apple
monitors. We are also actively encouraging further scientific research so we
can continue to promote the health and safety of our customers and employees.
Setting Up Your Monitor
3
Getting ready to set up your AppleVision 850AV Display
Before you set up your monitor, make sure you have easy access to the
following items that came with your AppleVision 850AV Display:
AppleVision
850AV Display
O
¤
®
Z
Monitor cable
Sound cable
Ambient light tool
Power cord
VGA adapter
User’s manual
Software
Note: Your power cord may look different from the one pictured.
4
Chapter 1
Your AppleVision 850AV Display at a glance
O Contrast
controls
Built-in
microphone
¤ Brightness
controls
Power
indicator light
® Power button
Control buttons
O
AppleVision
speakers
Z
Bass controls
Treble controls
V ADB port
(for mouse
or keyboard)
- Sound output port
(Plug in headphones
or external speaker
adapter here.)
Mute
indicator light
— Mute button
- Volume
Microphone indicator light
controls
Z Microphone button
Monitor cable
(includes monitor
connector and
ADB connector)
¤
®
X Sound input port
(Plug in audio CD
player, cassette
player, or microphone here.)
V ADB port
(for mouse
or keyboard)
Power cord
V ADB connector
Sound cable
(includes ≈ connector
and - connector)
™ Monitor connector
Setting Up Your Monitor
5
Getting ready to set up your AppleVision 850 Display
Before you set up your monitor, make sure you have easy access to the
following items that came with your AppleVision 850 Display:
AppleVision
850 Display
®
O
¤
Monitor cable
Ambient light tool
Power cord
VGA adapter
User’s manual
Software
Note: Your power cord may look different from the one pictured.
6
Chapter 1
Your AppleVision 850 Display at a glance
V ADB port
(for mouse
or keyboard)
O
¤
®
Power
indicator light
Control buttons
® Power button
O Contrast controls
Monitor cable
(includes monitor
connector and
ADB connector)
¤ Brightness controls
V ADB port
(for mouse
or keyboard)
Power cord
V ADB connector
™ Monitor connector
Setting Up Your Monitor
7
Do you need to install a video card?
The monitor is preadjusted and supports the following scan ranges:
m horizontal scan rate of 30–94 kilohertz
m vertical refresh rate of 48–120 hertz
In addition, the monitor works at the following VESA (Video Electronics
Standards Association) standard modes:
Resolution
Vertical refresh rate (hertz)
640 x 480
60-85
800 x 600
56-85
1024 x 768
60-85
1280 x 1024
75-85
1600 x 1200
75
The monitor also works at the following Macintosh standard modes:
Resolution
Vertical refresh rate (hertz)
832 x 624
75
1152 x 870
75
These are preassigned resolutions; your computer may support other
resolutions within this range. See the manual that came with your computer
or video card to determine which resolutions are supported.
For more information on factory preadjusted settings and other technical
information about your monitor, see Appendix B, “Technical Information.”
To use your monitor, you need compatible video circuitry built into your
computer or a compatible video card installed in your computer.
Note: The Apple 8•24, Apple 8•24GC, and most NuBus™ video cards are not
compatible with your monitor. In addition, some third-party PCI cards are not
fully compatible with your monitor.
8
Chapter 1
Mac OS–based computers
If you are not sure whether your computer has appropriate built-in video
capability, check with an Apple-authorized dealer or service provider. If your
computer does not have the video capability necessary to use your monitor,
you need to purchase a video card. (Video cards for Mac OS–based computers
are available from an Apple-authorized dealer or service provider.)
Install the video card before you connect the monitor to your computer. To
install a video card in one of the expansion slots inside your computer, see
the manual that came with your computer or video card.
Windows-based computers
Your monitor works with most Windows-based computers equipped with
VGA (Video Graphics Array) or greater capability. You may need to install a
video card to use the monitor with your computer. For more information, see
the manuals that came with your computer.
If you don’t use a preassigned resolution, you’ll need to adjust screen
geometry to match the new resolution. For more information, see “Adjusting
Screen Geometry” in Chapter 4.
Choosing a good location for your monitor
Here are some key factors to consider when determining where to place
your monitor:
m Be sure that the desk or table can support the monitor’s weight—
approximately 67 pounds (30 kilograms) for the AppleVision 850 Display
and approximately 77 pounds (35 kilograms) for the AppleVision 850AV
Display.
m Make sure that the power cord and monitor cable will easily reach from the
back of the monitor to your computer and wall outlet.
m The monitor cable should be unobstructed when you swivel and tilt the
monitor, so allow at least 7 inches (17.5 cm) of clearance in the back. If you
don’t allow enough clearance, the monitor connector might be damaged
when the cable hits an obstruction.
Setting Up Your Monitor
9
Positioning the monitor
IMPORTANT When you unpack or move the monitor, don’t set the monitor
down at an angle; you might damage the monitor stand.
Once your monitor is in place on a desk or table, follow these steps:
1
Place the monitor so the screen faces the user.
2
To slide the monitor, lift the front up slightly and push or pull in the direction you want.
3
Adjust the viewing angle of the monitor by tilting it up or down and turning it left or right
on its stand.
Position the monitor so that when you use it, no bright light is behind the
monitor or reflected on the screen. Your eyes should be about level with the
top edge of the screen and between 18 and 28 inches (45 to 70 cm) away. Take
occasional breaks when using your computer to focus your eyes on a
distant object.
For your greatest comfort, use the following illustration to help you in
positioning your monitor.
45–70 cm (18–28 in.)
Shoulders relaxed
Forearms and hands
in a straight line
Forearms level
or tilted up slightly
Lower back supported
Top of the screen at or slightly
below eye level (You may need
to adjust the height of your
monitor by placing something
under it or by raising your
work surface.)
Screen positioned to avoid
reflected glare
Clearance under work surface
Thighs horizontal
Feet flat on the floor
10
Chapter 1
Note: After you set up and configure the monitor, adjust the image and
colors on the screen to match your environment. For example, in a bright
room, contrast is usually best set at maximum; in a dim room, lower
contrast is usually more comfortable. See Chapter 2, “Installing and Using
AppleVision Software,” for more information about making screen and color
adjustments using AppleVision software for Mac OS–based computers. See
Chapter 4, “Using Your Monitor With Windows-Based Computers,” for
information about onscreen controls for adjusting screen image and color for
Windows-based computers.
Connecting the monitor to your computer
Follow these steps to connect your AppleVision 850 or 850AV to your computer.
Note: Although the AppleVision 850AV is shown in the illustrations, setup is
the same for the AppleVision 850, unless noted.
IMPORTANT Before you connect any cords or cables, make sure your computer
is turned off.
WARNING This equipment is intended to be electrically grounded. Your
monitor may be equipped with a three-wire grounding plug—a plug
that has a third (grounding) pin. This plug will fit only a grounded AC
outlet. This is a safety feature. If you are unable to insert the plug into
the outlet because the outlet is not grounded, contact a licensed
electrician to replace the outlet with a properly grounded outlet. Do not
defeat the purpose of the grounding plug!
Setting Up Your Monitor
11
Connecting the power cord
1
Connect the socket end of the power cord to the power cord receptacle on the back of
the monitor.
AppleVision
850AV Display
2
Plug the other end of the power cord into a grounded outlet or power strip.
Note: You may have a power jumper cord instead of a power wall cord. In
this case, plug the power jumper cord into the power socket on the back of
your computer.
Connecting the monitor cable to a Mac OS–based computer
Connecting to a standard monitor port
To realize the full capability of your monitor, you must connect it to the video
and ADB ports on your computer. The monitor cable is a split cable with two
connectors, one for video and one for the Apple Desktop Bus (ADB).
Monitor cable
Monitor connector
12
Chapter 1
ADB connector
1
Plug the monitor connector on the monitor cable into the monitor port (marked by ™)
on the back of your computer.
If your computer has more than one monitor port, see the manual that came
with your computer for information on choosing the correct port.
If you installed a video card in your computer, connect the monitor connector
on the monitor cable to the video card’s port. For more information about
installing video cards, see the manual that came with your computer or
video card.
2
Tighten the thumbscrews on the connection.
You can prevent bad connections and accidental damage by tightening
the thumbscrews. Do not overtighten the thumbscrews; you might
strip the threads.
3
Plug the ADB connector on the monitor cable into an ADB port (marked by V) on the
back of your computer.
Make sure the ADB connector is attached firmly.
IMPORTANT The ADB connector is not optional; it’s needed for your
Mac OS–based computer to work correctly with your monitor. If not
connected properly, extended resolutions and AppleVision software controls
will not be available.
If you have only one ADB port on the back of your computer and you’re
already using it for your keyboard and mouse, unplug the keyboard and
mouse and connect them directly to your AppleVision monitor. For more
information, see “Connecting a Mac OS–Based Computer Keyboard and
Mouse to Your Monitor” later in this chapter.
WARNING Make sure you don’t plug the ADB connector into an S-video
port (marked by æ or Æ) by mistake. The ports are the same size, and
it’s easy to mistake one for the other. It may cause electrical damage to
your computer or monitor.
IMPORTANT When connecting ADB cables, be sure to align the symbol V on
the connector with the same symbol on the port. If you force a connector the
wrong way, you will damage it.
Setting Up Your Monitor
13
Connecting the monitor cable to various video connectors
To connect the monitor to a high-density port (45-pin port) instead of a
standard monitor port (15-pin port), you need to use an adapter. This adapter
is usually provided with your computer. If you don’t have one, you can
purchase an adapter (Apple part number 590-0337) from an Apple-authorized
dealer.
45-pin high-density port
Monitor connector
Monitor cable
Adapter
(converts 45-pin
port to 15-pin port)
ADB connector
Other video connectors, such as PowerBook adapters, can also connect to
your monitor port with special adapters. For more information, see the
manual that came with your computer.
Note: If your Mac OS–based computer came with a VGA adapter for
connecting monitors, use it instead of the one shipped with your AppleVision
monitor.
14
Chapter 1
Connecting the monitor cable to a Windows-based computer
Although the monitor cable is a split cable with two connectors, you will use
only the monitor connector with your computer.
1
Connect the VGA adapter to the monitor connector (marked by ™) on the monitor
cable.
Monitor port on
Windows-based
computer
VGA adapter
∆
Monitor connector
2
Tighten the thumbscrews on the connection.
You can prevent bad connections and accidental damage by tightening
the thumbscrews. Do not overtighten the thumbscrews; you might
strip the threads.
3
Connect the VGA adapter end of the monitor cable to the monitor port on the back of
your computer.
If you installed a video card in your computer, connect the monitor cable
(with the VGA adapter attached to it) to the video card’s port. For more
information about installing video cards, see the manual that came with your
computer or video card.
4
Tighten the thumbscrews on the connection.
5
Leave the ADB connector on the monitor cable unplugged.
The ADB connector is for Mac OS–based computers only. Use the clip on the
monitor cable to move the connector out of the way.
Setting Up Your Monitor
15
Connecting a Mac OS–based computer keyboard and mouse
to your monitor
If you wish, you can plug your keyboard and mouse directly into the monitor,
rather than into the back of your computer. There is one ADB port on each
side of the monitor for your keyboard and mouse (or any other ADB device).
IMPORTANT Always be sure your computer is shut down before you plug in or
disconnect ADB cables.
1
Make sure the ADB connector on the monitor cable is plugged into an ADB port (marked
by V) on the back of your computer.
IMPORTANT The ADB connector is not optional; it’s needed for your
Mac OS–based computer to work correctly with your monitor. If not
connected properly, extended resolutions and AppleVision software controls
will not be available.
For more information, see “Connecting the Monitor Cable to a
Mac OS–Based Computer” earlier in this chapter.
2
If necessary, unplug the keyboard or mouse cable from the ADB connector on the back
of your computer.
3
Decide how you want to connect the keyboard and mouse.
For example, you can connect your mouse cable to your keyboard and then
connect the keyboard to one of the ADB ports (marked by V) on either side
of the monitor stand. Or, if you prefer, you can plug your keyboard and mouse
cables into the ADB ports (marked by V) on either side of the monitor stand.
4
16
Chapter 1
Connect your keyboard and mouse cables to the monitor’s ADB ports (marked by V)
according to your preference.
Connecting sound equipment to your AppleVision 850AV Display
Connecting the sound cable
The sound cable on your monitor is a split cable with two connectors, one for
sound input (such as a microphone or audio CD) and one for sound output
(such as a speaker).
Plug these connectors into your computer to use the built-in microphone and
speakers on your AppleVision 850AV Display. (This feature is not available on
the AppleVision 850 Display.)
1
Plug the connector (marked by ≈) on the sound cable into the sound input port on
your computer.
≈ Connector
- Connector
For Mac OS–based computers, the port (marked by ≈) is on the back of the
computer. For Windows-based computers, the connector (marked by ≈) fits
most standard microphone jacks. The sound input port on a Windows-based
computer may be located on a sound or multimedia card.
On some Windows-based computers, the connector (marked by ≈) on the
sound cable should only be plugged into the line level input port of your
sound card. See the documentation that came with your sound card to
determine where the appropriate line level input port is located.
2
Plug the connector (marked by -) on the sound cable into the sound output port on
your computer.
For Mac OS–based computers, the port (marked by -) is on the back of the
computer. For Windows-based computers, the connector (marked by _) fits
most standard speaker jacks. The sound output port on a Windows-based
computer may be located on a sound or multimedia card.
Setting Up Your Monitor
17
Connecting external sound equipment
The AppleVision 850AV Display has two sound ports you can use to
connect external sound equipment. The port on the left side of the monitor
is for connecting sound input equipment (such as an audio CD player,
cassette player, or microphone). The port on the right side of the monitor
is for connecting sound output equipment (such as headphones or
external speakers).
The monitor’s sound output port (marked by f) accepts a connector known
as a stereo miniplug. This connector is the type used on headphones for most
CD and cassette players.
The monitor’s sound input port (marked by ≈) accepts both the stereo
miniplug connector and an extended version of the miniplug. The extended
miniplug is slightly longer and is found on voice-quality microphones such as
the Apple PlainTalk Microphone.
Stereo miniplug
Extended miniplug
If your equipment has a different type of connector, you can purchase an
adapter at an electronics supply store.
18
Chapter 1
Connecting sound input equipment
To record sound, you can use the built-in microphone on your AppleVision
850AV Display, or you can connect external sound input equipment (such as
an audio CD player, cassette player, or external microphone) to the monitor.
To connect sound input equipment:
1
Make sure the connector (marked by ≈) on the sound cable is plugged into the sound
input port on your computer.
For most computers, the port (marked by ≈ on Mac OS–based computers) is
on the back of the computer.
2
Plug the sound input equipment into the sound input port (marked by ≈) on the left side
of the monitor.
Note: To use sound input equipment (such as an audio CD player, cassette
player, or external microphone), you must select the correct sound input
source. For Mac OS–based computers, use the Monitors & Sound control
panel. For Windows-based computers, press and release the microphone
button on the front panel of the monitor to switch between the built-in
microphone and the monitor’s sound input port, or see the manual that came
with your computer.
Connecting sound output equipment
If you wish, you can plug a pair of headphones (or other sound output
equipment) into the AppleVision 850AV Display.
To plug headphones into the monitor, follow these steps:
1
Make sure the connector (marked by -) on the sound cable is plugged into the sound
output port on your computer.
For most computers, the port (marked by - on Mac OS–based computers) is
on the back of the computer.
2
Plug the headphones into the sound output port (marked by f) on the right side of
the monitor.
Setting Up Your Monitor
19
Using more than one monitor
If your computer has expansion slots, you can use your monitor with one or
more additional monitors connected to your computer. You may need a video
card for each additional monitor you are using. See the manual that came with
your computer for more information.
If your Mac OS–based computer has one ADB port, you can still connect two
AppleVision monitors. You’ll need a special cable to split the ADB connector
cable into two parts.
AppleVision
850AV Display
Monitor cable
(includes monitor
connector and
ADB connector)
AppleVision
850 Display
Monitor cable
(includes monitor
connector and
ADB connector)
Shielded connector
cable (Apple part
number 590-0448)
IMPORTANT Make sure you use an Apple shielded connector cable. Most third-
party ADB splitter cables are not shielded and will not work properly with
your AppleVision monitor. (You may experience more radio interference with
an unshielded connector cable.)
20
Chapter 1
Turning the monitor on
To turn on the monitor for the first time:
1
Plug in the computer’s power cord.
2
Press the power button on the monitor.
Power indicator light
O
¤
®
Power button
Z
AppleVision
850AV Display
If you plug your monitor directly into your computer, no power indicator light
goes on until you start up your computer. If you plug your monitor into a wall
outlet, the monitor’s amber power indicator light goes on. When you start up
your computer, the indicator light turns green.
3
Start up your computer and wait a few seconds.
The green power indicator light goes on. If the power indicator light does not
go on, press the monitor’s power button again. If this doesn’t work, make sure
you’ve connected the monitor cable and power cord properly. (See
“Connecting the Monitor to Your Computer” earlier in this chapter.) Also,
make sure your computer is turned on and no energy-saving or screen-saving
features are active. The power indicator light on the monitor is amber when
an energy-saving program is on.
Setting Up Your Monitor
21
For Mac OS–based computers, you must first install the AppleVision software
that came with your monitor before adjusting the screen with the front panel
buttons and using other monitor features. For more information on
AppleVision software installation and Energy Saver, see Chapter 2,
“Installing and Using AppleVision Software.”
WARNING Before making any screen or sound adjustments, install the
AppleVision software on your Mac OS–based computer. Using software
other than the new AppleVision software that came with your monitor
could damage your monitor.
Using the monitor with Windows-based computers
In most cases, once you turn on the monitor, you will not have to make any
adjustments to the screen image. If necessary, you can adjust or fine-tune the
image to suit your personal preference. For more information about adjusting
the screen image, see Chapter 4, “Using Your Monitor With Windows-Based
Computers.”
To change resolutions on your monitor, see the manuals that came with your
operating software or video card.
Note: The AppleVision Software CD-ROM disc includes AppleVision setup
information for Windows 95 users. See Chapter 4, “Using Your Monitor With
Windows-Based Computers,” for installation instructions.
22
Chapter 1
Finding answers
When you have questions about using your monitor, there are several places
you can look for answers.
This manual
Ap
DisplapyleVision
••
• • •• ••
User’s ma
•• •• ••
nual for the
••
AppleVision
850 and 85
0AV
Use this manual to set up your monitor, install AppleVision software
for Mac OS–based computers, install AppleVision setup information
and use onscreen controls for Windows-based computers, and find
solutions to common problems.
Apple Guide for Mac OS–based computers
If you need help or experience a problem while using the
AppleVision software, open the Guide (h) menu and choose
Macintosh (or Mac OS) Guide or Monitors & Sound Guide. The
Guide menu is the main source for information about the
AppleVision software and your Mac OS–based computer. See
Chapter 2 for more information.
AppleVision software instructions for System 7.1 users
If you’re using System 7.1, Apple Guide isn’t available. Instead,
open the Monitors & Sound doc.pdf file using Adobe Acrobat
Reader to view AppleVision software instructions. See Chapter 2
for more information.
Obtaining online support and updated Apple software
Apple technical support information and software updates are available from
many online services. You can get troubleshooting and other important
information by using these services. You can also get the latest versions of
Apple software, including most printer drivers, system enablers, and updates
to utilities and networking and communications software.
Support information and Apple software updates are available via Apple’s
World Wide Web sites:
m http://www.info.apple.com
m http://www.support.apple.com
Setting Up Your Monitor
23
What to do next
Mac OS–based computers
Go to the next chapter for information about installing and using
AppleVision software.
Windows-based computers
Go to Chapter 4, “Using Your Monitor With Windows-Based Computers,” for
information on installing AppleVision setup information and using the
control buttons to open onscreen menus for screen image and
sound adjustments.
24
Chapter 1
2
Installing and Using AppleVision Software
This chapter explains how to install AppleVision software on your
Mac OS–based computer and provides an overview of software features. If
you’re using the monitor with a Windows-based computer, see Chapter 4,
“Using Your Monitor With Windows-Based Computers.”
Installing AppleVision software
To install AppleVision software on a Mac OS–based computer, follow
these steps:
1
Make sure you have System 7.1 or later installed.
You need a Mac OS–based computer running System 7.1 or later to use the
software. If you don’t have System 7.1 or later, contact an Apple-authorized
dealer or service provider.
Note: You must connect your monitor to a computer with a 68040 processor
or PowerPC™. The monitor does not work with computers that have been
upgraded to a 68040 processor from earlier processors, such as a 68030
processor.
2
Insert the AppleVision Software CD-ROM disc into the computer’s CD-ROM drive.
The CD icon appears on the desktop.
Note: If you don’t have a CD-ROM disc drive, you can order a set of floppy
disks of the AppleVision software. See the service and support information
that came with your monitor for more information.
25
3
Double-click the CD icon to see what’s on the CD-ROM disc.
The AppleVision Software CD window opens.
4
Double-click the folder that contains your language preference.
For example, if you’d like to install AppleVision software in English,
double-click the English folder.
5
Double-click the AppleVision Software folder.
6
Double-click the AppleVision Read Me file and read the document.
The AppleVision Read Me file contains important information about the
applications included with your AppleVision software. It also provides a list of
installed software for your reference.
7
Choose Quit from the File menu when you’re finished reading.
8
Double-click the AppleVision Installer icon to start the Installer program.
A welcome screen appears.
9
Click Continue.
The software license agreement dialog box appears.
Note: Be sure you’re acting within the terms of the software license
agreement before you agree to install this software on your computer. The
license agreement specifies how many copies of the program you can make
for yourself and others.
26
Chapter 2
10
Click Agree once you’ve read and agreed to the terms in the document.
The Install AppleVision Software dialog box appears. The software version
number shown on your screen might be different from the one illustrated
here.
Destination disk
11
Make sure the destination disk named is the startup disk of your computer. If it isn’t,
click Switch Disk until you see the right name.
12
Select Easy Install; then, click Install.
The Installer takes a few minutes to calculate what needs to be done and then
begins to copy files. If you are running other applications, a message appears
telling you to quit any open applications. Click Continue to quit the
applications and continue with the installation.
Note: Make sure you use the Installer to install the software. Do not install
the software by dragging files.
13
Follow the instructions on the screen until the installation is complete.
IMPORTANT The Installer checks to make sure you have the system software
you need to use the monitor. If you’re missing anything, a message tells you
what you need. You won’t be able to install the software until you correct the
problem. If a dialog box says you don’t have the correct system software, you
can purchase a new version from an Apple-authorized dealer.
After the installation, the Installer tells you to restart your computer.
14
Click Restart.
The software is now installed and the monitor is ready for use.
Installing and Using AppleVision Software
27
IMPORTANT If you reinstall system software on your computer, you must
reinstall the AppleVision software.
Note: If you press a control button under the screen on the left front of your
monitor and do not see the Monitors & Sound control panel, you probably
haven’t set up your AppleVision monitor correctly. Make sure the ADB
connector on the monitor cable is connected directly to your computer’s ADB
port. See Chapter 1, “Setting Up Your Monitor,” for more information.
Learning about AppleVision software with System 7.5 or later
This section explains how to open Monitors & Sound Guide for information
about using AppleVision software with your monitor. If you’re using
System 7.1, see the next section, “Learning About AppleVision Software
With System 7.1.”
The Monitors & Sound Guide is your main source of information about
AppleVision software. The Guide menu is identified by a question mark (h)
in the upper-right corner of the screen.
Open Monitors & Sound
Guide when the Monitors &
Sound control panel is
active to get onscreen help
on AppleVision software.
To open Monitors & Sound Guide, make sure your Monitors & Sound control
panel is active. Then, click the Guide (h) icon on the top right corner of the
control panel to open Monitors & Sound Guide or choose Monitors & Sound
Guide in the Guide (h) menu at the top of your screen.
Macintosh (or Mac OS) Guide also contains the same information about the
AppleVision software as well as other information about using your computer.
Macintosh Guide is available while you’re in the Finder.
28
Chapter 2
Monitors & Sound Guide provides onscreen help on how to use AppleVision
software.
Monitors & Sound Guide provides information about the following topics:
sound, monitors (AppleVision extras), monitors (standard settings), and
troubleshooting. Click the Topics button to open these topic areas and
choose a topic. Then, select a question in the list and click OK to open
detailed instructions.
Tips for using Monitors & Sound Guide
When you can’t find the information you need
m In searching for help topics, use all three buttons at the top of Guide’s
initial window: Topics, Index, and Look For.
m If you’re in a series of steps and want to return to the list of help topics,
click the button marked Topics in the Guide window.
When you can’t see what’s behind the Guide window
Guide windows stay in front of other windows on the screen so that your
instructions are never covered.
m Drag a Guide window by its title bar to move it out of the way.
m Click the zoom box once to shrink a Guide window. (To expand the
window, click the zoom box a second time.)
Installing and Using AppleVision Software
29
When you need more information about an instruction or term
m Click the “Huh?” button if it is available.
m If an unfamiliar word is underlined, click it to get a definition.
Title bar
Zoom box
Topics button
“Huh?” button
Navigation buttons
Learning about AppleVision software with System 7.1
Because Monitors & Sound Guide is not available to System 7.1 users,
AppleVision software instructions are provided onscreen in a pdf file format.
To view the instructions, you must first install Adobe™ Acrobat™ Reader
(included on the AppleVision Software CD-ROM disc).
To install Adobe Acrobat Reader, follow these steps:
30
Chapter 2
1
Insert the AppleVision Software CD-ROM disc into the computer’s CD-ROM drive.
2
If necessary, double-click the CD icon to open the AppleVision Software CD window.
3
Double-click the folder that contains your language preference.
4
Double-click the Acrobat Reader folder.
5
Double-click the ACROREAD.MAC icon to start the Installer program.
6
Click Continue in the first dialog box.
7
After you’ve read and agreed to the terms and conditions of the license agreement,
click Continue.
8
Make sure that the disk that appears in the Install Location box is the startup disk of your
computer; then click Install.
9
When installation is complete, click Restart in the dialog box that appears.
You’re now ready to use Acrobat Reader to view AppleVision software
instructions.
10
Go to the Apple Extras folder on your hard disk and double-click the folder; then doubleclick the AppleVision Extras folder to view its contents.
Double-click Monitors & Sound doc.pdf to view AppleVision software
instructions using Acrobat Reader.
For more information about Adobe Acrobat Reader, see the ReadMeReader2.1 file in the Acrobat Reader folder installed on your hard disk.
Installing and Using AppleVision Software
31
Screen controls at a glance
The buttons on the front of your monitor provide a quick way to adjust the
screen image. In most cases, you won’t need to adjust the screen image unless
you make changes to screen resolution.
Control buttons
Press any button to open the
Monitors & Sound control panel.
Contrast controls
Press ¿ to increase
contrast; press ÷ to
decrease contrast.
O
Brightness controls
Press ¿ to increase
brightness; press ÷ to
decrease brightness.
¤
®
Power button
Press to turn
power on or off.
The Contrast and Brightness adjustments have an onscreen indicator that
appears when you press a button on the front of your monitor. For example,
pressing a Brightness button displays the Brightness indicator.
Lowest
setting
Current
setting
Highest
setting
When you make an adjustment, the indicator bar moves to show the
current setting. When you’ve finished making adjustments, the indicator
disappears automatically.
32
Chapter 2
About the Monitors & Sound control panel
The Monitors & Sound control panel allows you to control the way your
computer displays images and processes sound. Because different computers
have different capabilities, Monitors & Sound automatically adjusts itself
based on the video and sound capabilities of the computer and monitor you’re
using. That’s why the Monitors & Sound control panel shown in this manual
may appear slightly different on your computer.
If you have more than one monitor attached to your computer, a separate
Monitors & Sound control panel will appear on each one, allowing you to
customize your settings for each monitor separately.
Opening Monitors & Sound
There are two ways to open the Monitors & Sound control panel:
m Choose Control Panels from the Apple (K) menu; then select Monitors
& Sound.
m Press one of the control buttons under the screen on the left front of your
AppleVision monitor.
After a moment, the Monitors & Sound control panel appears on your screen.
Installing and Using AppleVision Software
33
Monitors & Sound buttons at a glance
The large buttons across the top of the Monitors & Sound control panel are
used to select different options. See Monitors & Sound Guide or the Monitors
& Sound doc.pdf file for detailed information on using the AppleVision
software.
Button
Description
Use the Monitor button to adjust color depth, resolution, contrast, and
brightness settings.
Use the Arrange button to configure more than one monitor. This button appears on
your screen if you have more than one video port on your computer.
Use the Sound button to adjust your computer system’s sound. You can also set the
volume and balance for speakers attached to your computer, choose sound input
devices such as a microphone or CD player, and select sound output quality.
Use the Alerts button to change your computer’s alert sound.
Use the Geometry button to change the image options for your monitor. You can
change the size and shape of the screen image, adjust convergence, and turn
overscan on and off.
Use the Color button to change color calibration, gamma curve, white point, and
ambient light settings, and to import or export a ColorSync profile. (For more
information on ColorSync, see Appendix A.)
Use the Monitor Sound button to control the monitor’s internal speakers and devices
connected to your AppleVision 850AV Display. (These features are not available on
the AppleVision 850 Display.)
34
Chapter 2
Tips for using AppleVision software
m For best results, recalibrate your monitor after changing the color settings.
For example, color adjustment changes don’t take effect until you click
Recalibrate. You can choose to have your monitor recalibrate automatically
whenever you change the settings. Click the Color button. Then click
Preferences. After selecting your recalibration preferences, click Save.
m To use the default settings shipped with your monitor, click the Geometry
button. When the Geometry window opens, click the Factory Settings
option. To use the color default settings, click the Color button. When
the Color window opens, double-click Factory Defaults in the Saved
Settings menu.
m Red, green, and blue signals in your monitor overlay, or converge, to create
the colors you see on your screen. If the convergence is not set properly,
images or text on your screen may appear blurred, or you may get a
“rainbow” effect in which several colors form the edges of images on the
screen. If you move your monitor to another location, you may need to
change the convergence to get a clear, distinct screen image. To adjust
convergence, click the Convergence button in the Geometry window.
m When overscan is on, you may not be able to choose commands from the
menus at the top of your monitor. If this occurs, you can’t use a menu to
open the Monitors & Sound control panel and turn overscan off. Instead,
open Monitors & Sound by pressing a Control button on the front of
your monitor.
m The ColorSync profile included with your monitor works with other device
profiles to ensure the closest match possible between monitor color and
printed color. See “Using ColorSync” in Appendix A for more information.
To refine the color profile, you can use the Color window in Monitors &
Sound to further adjust for your specific monitor and lighting conditions.
m To correct for ambient light conditions, you must set the color depth on
your monitor to Millions of Colors. If you can’t set color depth to Millions
of Colors, try changing to a lower screen resolution. Use the Color button
to open color depth and resolution settings.
Installing and Using AppleVision Software
35
Using the Control Strip
When you turn on your monitor, a small pull tab appears in the lower-left
corner of the screen. Click once on the pull tab to open it. This is called the
Control Strip.
Scroll arrows let you view
Control Strip items that are
not visible.
Pull tab
Close Box
For changing
color depth
For changing
screen resolution
The Control Strip is a quick and easy way to make changes to the features you
use most on your computer, such as screen resolution and color depth.
The Control Strip may look slightly different depending on the options on
your computer. Move the pointer over the item you want to use and hold
down the mouse button. A pop-up menu appears with a selection of choices.
Hold down the Option key and drag the Control Strip up or down the left or
right side of the desktop. Release the Option key and mouse button when the
Control Strip is located where you want it.
Using DigitalColor Meter
DigitalColor Meter and your monitor work together to identify colors on your
screen based on the standard color gamuts defined by the Commission on
Illumination (CIE).
DigitalColor Meter can also identify colors using the Pantone® system.
Pantone is a color-matching system used to specify ink colors for high-end
printers. Pantone colors are described using their printing ink formulation,
which is identified by a specific Pantone number. DigitalColor Meter
performs color matching and provides Pantone numbers for coated (CVC),
uncoated (UVC), and process (CVP) color samples. Use the Pantone numbers
when you have your work professionally printed to ensure that the printer will
use colors similar to those displayed on your screen.
36
Chapter 2
Finally, you can use DigitalColor Meter to identify the RGB (red, green, blue)
values your computer uses to create colors.
Opening DigitalColor Meter
Choose DigitalColor Meter from the Apple (K) menu. (It was installed with
your AppleVision software.)
When you launch DigitalColor Meter, its window opens on your monitor.
See DigitalColor Meter Guide (located in the Guide [h] menu when the
DigitalColor Meter application is active) or the Monitors & Sound doc.pdf
file for more information on how to use DigitalColor Meter.
Installing and Using AppleVision Software
37
Specifying colors using the Pantone Matching System
In some application programs, you can use Apple Color Picker to specify
Pantone colors. The Pantone Color Picker extension is automatically installed
along with the rest of the AppleVision software.
For example, in a variety of applications, Apple Color Picker is automatically
launched when a new color needs to be specified. Often, a menu of several
different color systems is available to choose from. When you select Pantone,
a dialog box appears.
By selecting Pantone matching colors, you are assured of a close match
between what you see on your monitor and the printed version. Pantone Color
Picker may look different on your computer.
If Pantone colors are not available in the Color Picker menu, click the More
Choices button; then select Pantone.
Conserving energy
Use the Energy Saver control panel to tell the monitor whether to conserve
energy after a specified period of inactivity.
You can use the control panel with your AppleVision monitor or any other
Apple monitor that complies with the United States Environmental Protection
Agency’s Energy Star program. (Look for the EPA Energy Star logo on the
monitor box.)
38
Chapter 2
Note: When you save energy, you save natural resources and reduce
pollution. Although the AppleVision 850 and 850AV contain features that
automatically save energy, you can increase the energy savings by turning the
computer off if you won’t be using it for awhile—for example, overnight or
over the weekend.
For more information about power-saving and environmental features, see
Appendix B.
Setting up Energy Saver
To use the Energy Saver control panel, follow these steps:
1
Choose Control Panels from the Apple (K) menu.
If you’re using System 7.5, a pop-up menu appears. If you’re using System 7.1,
a window opens showing all the control panels.
2
Choose Energy Saver or double-click the Energy Saver icon to open the Energy Saver
control panel.
3
Make the following choices in the control panel:
Click to turn Energy
Saver on or off.
When there’s an X
in this box, Energy
Saver is on.
If Energy Saver is on, slide this control to determine
how long Energy Saver will wait without activity before
darkening the screen.
IMPORTANT If you’ve installed the AppleVision software that came with your
monitor and the Energy Saver icon still doesn’t appear or the Energy Saver
control panel doesn’t look like the one above, you may have a different type
of energy-saving software. In this case, instructions in this section don’t apply.
See Macintosh (or Mac OS) Guide for instructions on saving energy. To open
Macintosh Guide, choose Macintosh Guide from the Guide menu (marked
with the h icon) when the Finder is active.
Note: Not all Mac OS–based computers work with Energy Saver. See
“Troubleshooting Common Problems” in Chapter 5 for more information.
Installing and Using AppleVision Software
39
4
Close the control panel.
IMPORTANT If you use Energy Saver, make sure you turn it off when you’re
doing disk-intensive tasks such as copying a large number of files,
downloading large files from an online service, or printing a very large file.
If Energy Saver is activated during a disk-intensive task, the task may be
terminated prematurely and you may need to recopy or reprint a file.
What happens after you turn on the energy-saving feature?
When Energy Saver detects that you’re not using the computer, it darkens the
monitor screen and reduces the amount of energy it consumes. While the
monitor is darkened, your computer is still working, but to avoid accidental
changes, Energy Saver won’t let anything you type or do with the mouse
affect any of your work.
To “wake up” the monitor, press any key on the keyboard. Your computer
beeps while the monitor is waking up and you can begin work as soon as the
computer stops beeping. (The beep volume cannot be adjusted; it is
independent of all system sound controls.)
You will save the most energy if your AppleVision 850AV monitor speakers
are turned off in energy saver mode. This stops sound output during sleep,
but will also prevent you from hearing the complete start up sound when
turning on or restarting your computer. If you prefer to hear a system startup
sound, you can turn off this option. Click the Preferences button in the
Monitor Sound window; then leave the option, “Turn Speakers Off in Energy
Saver Mode,” unchecked.
Using Energy Saver with a screen saver
Screen savers are applications you can purchase that put moving patterns on
your monitor. Screen saver and Energy Saver applications prevent screen
“burn-in.” Energy Saver also conserves energy.
If you wish, you can use Energy Saver and a screen saver program. Set the
screen saver to come on before Energy Saver. If your screen saver program
includes its own energy-saving feature, you can turn off Energy Saver.
40
Chapter 2
3
Using Sound and Video
With Your AppleVision 850AV Display
This chapter describes how to adjust sound on the AppleVision 850AV Display
and a Mac OS–based computer. It also describes how to set up your monitor
to record a video with sound and play an audio CD through the monitor’s
speakers.
If you’re using a Windows-based computer, see Chapter 4, “Using Your
Monitor With Windows-Based Computers,” for more information.
41
Sound controls at a glance
The buttons on the front of your AppleVision 850AV Display provide a quick
way to adjust monitor sound.
O
¤
®
AppleVision
850AV Display
Z
Bass controls
Press ¿ to increase bass;
press ÷ to decrease bass.
Microphone button
Press to turn the monitor’s
built-in microphone on or off.
Treble controls
Press ¿ to increase treble;
press ÷ to decrease treble;
press both to turn 3D sound
on or off.
Mute button
Press to turn
mute on or off.
Volume controls
Press ¿ to increase volume;
press ÷ to decrease volume.
Bass, treble, and volume adjustments have an onscreen indicator that appears
when you press a button on the front of the monitor. For example, pressing
the Bass button displays the Bass indicator.
When you make an adjustment, the indicator bar moves to show the
current setting. When you’ve finished making adjustments, the indicator
disappears automatically.
42
Chapter 3
About sound sources
Depending on the kind of Mac OS–based computer your AppleVision 850AV
Display is connected to, you may have several sound input and output
sources:
Sound input sources
m the AppleVision 850AV Display
You can record from the built-in microphone or sound equipment
attached to the monitor’s sound input port (marked by ≈) on the left side
of the monitor.
m an internal CD-ROM drive
m equipment connected to the back of your computer
This can be an external CD-ROM drive, cassette player, and so on.
Sound output sources
m the AppleVision 850AV Display
You can play sound on the built-in speakers or on sound equipment (such
as headphones) attached to the monitor’s sound output port (marked by f).
m equipment connected to the back of your computer
This can be headphones, speakers, and so on.
To play and record sound, you must first select a sound input source and a
sound output device using the Monitors & Sound control panel. See Monitors
& Sound Guide or the Monitors & Sound doc.pdf file for instructions on how
to use these and other options available with AppleVision software.
Selecting sound options in Monitors & Sound
Use the Sound button in the Monitors & Sound control panel to configure
and adjust sound on your Mac OS–based computer system. Use the Monitor
Sound button to configure and adjust sound on your AppleVision 850AV
Display.
Using Sound and Video With Your AppleVision 850 A V Display
43
The following options are available with each button. Some of the options
may not be available with your computer/monitor configuration. See Monitors
& Sound Guide or the Monitors & Sound doc.pdf file for detailed
information on using the AppleVision software.
Button
Description
Use the Sound button to choose sound sources for your computer. You can
m select a sound input port on your computer
m set the desired sound output quality
m set the sound out level
Use the Monitor Sound button to choose sound sources for your monitor. You can
m select a sound input source for your monitor
m set the desired gain level for best sound quality while recording or playing sound
m select how the sound from the monitor’s input port is routed through your computer
system
m set the monitor speaker volume, treble, bass, and sound preferences
m turn 3D sound on and off
Tips for using sound controls
m For most Mac OS–based computers, any sound coming from the computer
(from an internal CD-ROM drive, for example) automatically goes to the
computer’s internal speakers and sound output port. The built-in speakers
on your computer are muted automatically when sound equipment (such as
the AppleVision monitor) is connected to the sound output port on the
back of the computer.
m For best results, adjust the volume on your computer with the Sound
controls. Then, use the Monitor Sound controls to adjust the volume on
your monitor.
m If you have more than one monitor attached to your computer, the settings
in the Monitors & Sound control panel apply only to the monitor listed
near the top of the window. The other monitor will have its own Monitors
& Sound control panel.
44
Chapter 3
Setting up your monitor to record a video with sound
The following sections describe how to use your AppleVision 850AV Display
to record a video with sound. To record a video with sound, you must have a
Mac OS–based computer that supports video. For more information about
connecting and using video equipment with your computer, see the manuals
that came with your computer and video equipment.
About video equipment
If you have a Mac OS–based computer that supports video, you can connect
video equipment so that you can display, edit, and store video images on the
computer. You can also view or record images on a television or video cassette
recorder (VCR).
Your Mac OS–based computer can work with two major video formats:
m S-video, a high-quality video format used by many video cameras and
VCRs
m composite video, a video format used by televisions, most VCRs, and laser
disc players
To find out which format your equipment uses, check the manual that came
with your equipment.
Mac OS–based computers that support video have S-video ports, composite
video ports, or both. The video input port brings in images from connected
external equipment such as a VCR. The video output port sends images out
from the computer to the external equipment.
Using Sound and Video With Your AppleVision 850 A V Display
45
The following illustration shows S-video and composite video ports on a
Mac OS–based computer.
Note: The video ports on your computer may be in a different position.
˜ Composite video input port
Connects your Mac OS–based computer
to the RCA-type Video Out port of most
VCRs, laser disc players, video cameras,
and other video input equipment
æ S-video input port
Connects your
Mac OS–based computer
to the S-video Out port
of VCRs, laser disc players,
video cameras, or other
video input equipment that
uses an S-video connector
46
Chapter 3
 Composite video output port
Connects your Mac OS–based
computer to the RCA-type
Video In port of most VCRs, or
other video recording or video
display equipment
Æ S-video output port
Connects your
Mac OS–based computer
to the S-video In port of
VCRs, or other video
recording or video display
equipment that uses an
S-video connector
The S-video connector is a round plug with several small metal pins. You can
plug the S-video input connector into your computer’s S-video input port and
the S-video output connector into your computer’s S-video output port.
S-video connector
IMPORTANT The S-video connector resembles other Mac OS–based computer
connectors, such as those for a printer, modem, mouse, or keyboard. Don’t
confuse the connectors; they are not interchangeable.
Some video devices use composite video format instead of S-video. The
cables for these devices have RCA-type plugs.
RCA plug
If your video equipment has an RCA-type plug and you don’t have a
composite video port on your Mac OS–based computer, you’ll need an
adapter to connect your video equipment to the S-video port on your
computer. The adapter converts an RCA plug into an S-video plug. You can
purchase one from an Apple-authorized dealer or electronics supply store.
Using Sound and Video With Your AppleVision 850 A V Display
47
Using video equipment with your monitor
The instructions that follow are for connecting a stereo VCR to a Mac
OS–based computer with an S-video port or a composite video port, but you
can use them as a model for connecting your computer to any video equipment.
Before you start:
m Make sure that the VCR has a cable with an S-video connector or a
composite (RCA plug) connector. If the VCR has an RCA plug, make sure
you have an adapter if your computer does not have a composite
video port.
m Place the VCR near your computer system.
m Shut down the computer and turn off the VCR.
Note: If your computer has a sound input port and a sound output port in
addition to the S-video or composite video ports, you can connect all cables
to the back of your computer. See the next section for information.
1
Assemble the cables you need to connect the VCR.
You need the following cables (available at an electronics supply store):
m video cable with S-video connectors or RCA plugs at each end (If you’re
using a video cable with RCA plugs, you’ll also need an adapter cable if
your computer does not have a composite video port.)
S-video
S-video
RCA
RCA
Adapter for composite video
S-video
m audio cable with dual RCA plugs at one end and a 3.5-mm stereo miniplug
at the other end
RCA
Stereo miniplug
48
Chapter 3
2
Plug one end of the video cable into the Video Out port on the VCR.
Follow the instructions that came with the VCR.
3
Plug the other end of the video cable into the S-video input port (æ) or the composite
video input port (˜) on your computer.
If the connector doesn’t slide easily into the port, realign it and try again.
Don’t use force, which could damage the computer or cable.
4
Plug the dual RCA plugs on the audio cable into the left and right Audio Out ports on
the VCR.
5
Plug the stereo miniplug on the audio cable into the sound input port (marked by ≈) on
the left side of your AppleVision 850AV Display.
Your finished S-video connections should look like this:
≈ Sound input port
Video Out
port
Audio Out ports
(left and right)
æ S-video
input port
VCR
3.5-mm miniplug to dual RCA-plug cable
(available at most electronics supply stores)
Monitor cable
(includes monitor connector
and ADB connector)
Sound cable
If you use composite video connections, your finished connections will
be similar.
6
Turn on the computer, the monitor, and the VCR.
Using Sound and Video With Your AppleVision 850 A V Display
49
Connecting all audio and video cables to the back of your computer
When you record a video with sound, you can connect all the video
equipment to the back of your computer if your computer has S-video or
composite
video ports as well as sound input and sound output ports for the monitor’s
sound cable.
To set up your computer for this configuration, follow these steps:
1
Assemble the cables you need to connect the VCR.
You need the following cables (available at an electronics supply store):
m video cable with S-video connectors or RCA plugs at each end (If you’re
using a video cable with RCA plugs, you’ll also need an adapter cable if
your computer does not have a composite video port.)
S-video
S-video
RCA
RCA
Adapter for composite video
S-video
m audio cable with dual RCA plugs at one end and a 3.5-mm stereo miniplug
at the other end
RCA
Stereo miniplug
m audio cable with dual RCA plugs at each end
Dual RCA plug
2
Attach one end of the video cable into the Video Out port on the VCR.
Follow the instructions that came with the VCR.
50
Chapter 3
3
Plug the other end of the video cable into the S-video input port (æ) or the composite
video input port (˜) on your computer.
If the connector doesn’t slide easily into the port, realign it and try again.
Don’t use force, which could damage the computer or cable.
4
Plug one end of the dual RCA plug cable into the left and right Audio Out ports on
the VCR.
5
Plug the other end of the dual RCA plug cable into the left and right audio input ports on
the back of your computer.
6
Plug the stereo miniplug cable into the sound input port (marked by ≈) on the left side of
your AppleVision 850AV Display.
7
Plug the RCA plug end of the stereo miniplug cable into the audio output ports of
your computer.
Your finished S-video connections should look like this:
æ S-video
input port
Video Out
port
- Audio
input ports
(left and right)
Audio Out ports
(left and right)
VCR
Dual RCA-plug cable
(available at most electronics supply stores)
Monitor cable
(includes monitor connector
and ADB connector)
Sound cable
If you use composite video connections, your finished connections will
be similar.
8
Turn on the computer, the monitor, and the VCR.
Using Sound and Video With Your AppleVision 850 A V Display
51
Recording a video
After the video equipment is connected to your computer and monitor, you
can record a video. See the manual that came with your video application for
more information. For example, your application may have additional options
for setting sound sources, volume, and so on. Make sure these are set properly.
Playing an audio CD through the monitor’s speakers
You can connect an audio CD player to the AppleVision 850AV Display and
play the sound through the monitor’s speakers.
To play an audio CD, follow these instructions:
1
Turn off the audio CD player and connect it to the sound input port (marked by ≈) on the
left side of the monitor.
Your monitor and external audio CD player should be connected like this:
≈ Sound input port
Audio Out port
CD
Miniplug cable
(available at most electronics supply
stores or included with CD player)
For more information, see “Connecting Sound Equipment to Your
AppleVision 850AV Display” in Chapter 1.
2
Click the Sound button in the Monitors & Sound control panel to open the Sound window.
Make sure you select the appropriate sound input device, such as the
microphone or external audio, when you use an external audio CD player.
3
52
Chapter 3
Click the Monitor Sound button and adjust the sound input Port Gain to “line level.”
4
Click Routing.
5
Click Computers and Speakers; then click OK.
6
Turn on the audio CD player and play a CD.
7
Adjust speaker volume as desired.
Use the Speaker Volume slider in the Monitors & Sound control panel or
press the volume buttons (marked by -) on the front of your monitor. You
should hear the CD sound on your monitor speakers. If not, make sure the
audio CD player is connected properly and the audio CD is playing.
Note: You can also use a Mac OS–based computer’s internal CD drive to
listen to and record from. Use the AppleCD Audio Player application
available in the Apple (K) menu. The AppleCD Audio Player automatically
selects all the appropriate settings.
Using Sound and Video With Your AppleVision 850 A V Display
53
4
Using Your Monitor
With Windows-Based Computers
This chapter describes how to install the AppleVision setup information
and adjust the screen image on the AppleVision 850 and 850AV. In most
cases, you won’t need to adjust the image unless you make changes to
screen resolution. This chapter also explains how to control sound on the
AppleVision 850AV Display.
For more information about power-saving and environmental features of your
AppleVision monitor, see Appendix B.
Note: If you’re using the monitor with a Mac OS–based computer, refer
to Chapter 2, “Installing and Using AppleVision Software” and Chapter 3,
“Using Sound and Video With Your AppleVision 850AV Display.”
55
Installing AppleVision setup information for Windows 95
On Windows 95 systems, new devices are automatically detected when they
are connected to your computer (if it is VESA DDC compliant). If you are
not using Windows 95, see the manual that came with your video card for
setup information.
To determine that Windows 95 has correctly identified your monitor, check
Monitor Type in the Display Properties dialog box. Performing this check will
ensure that the AppleVision setup information has been installed. Not
installing the AppleVision setup information may limit the resolution and
refresh rates on your monitor.
To correctly identify the monitor type in your computer, follow these steps:
1
Open the Start menu and choose Settings.
2
Open the Control Panel and double-click the Display icon.
The Display Properties dialog box appears.
3
Click the Settings tab at the top of the dialog box.
The Settings property sheet appears.
4
Click the Change Display Type button in the lower-right corner to display the current
Monitor Type.
If the Monitor Type shown is the AppleVision 850, your computer has
correctly identified your monitor. Go to the next section, “Screen Controls
at a Glance.”
If the Monitor Type shown is not the AppleVision 850, continue with step 5.
5
Press the Change button next to the Monitor Type field; then select AppleVision 850 and
click OK.
If AppleVision 850 is not one of the devices displayed, then the AppleVision
setup information file needs to be installed.
56
Chapter 4
6
Insert the AppleVision Software CD-ROM disc into your CD-ROM disc drive.
If you do not have a CD-ROM disc drive, see the service and support
information that came with your monitor for information on how to order
floppy disks.
7
Click the Have Disk button.
8
Choose the CD-ROM disc drive and click OK.
If an error occurs, make sure you’ve selected the correct disc drive.
9
Choose the AppleVision 850 in the Monitor Type field and click OK.
You’re now ready to use the AppleVision monitor with your computer.
Screen controls at a glance
The buttons on the front of your monitor provide a quick way to adjust the
screen image. In most cases, you won’t need to adjust the screen image unless
you make changes to screen resolution.
Use the following buttons to make screen image adjustments:
Control buttons
Use these buttons to make screen
image adjustments. See “Using
Onscreen Controls” later in this chapter.
Contrast controls
Press ¿ to increase
contrast; press ÷ to
decrease contrast.
O
Brightness controls
Press ¿ to increase
brightness; press ÷ to
decrease brightness.
¤
®
Power button
Press to turn
power on or off.
The contrast and brightness adjustments have an onscreen indicator that
appears when you press the contrast and brightness control buttons on the
front of your monitor. When you make an adjustment, the indicator bar moves
to show the current setting. When you’ve finished making adjustments, the
indicator disappears automatically.
Using Your Monitor With Windows-Based Computers
57
Using onscreen controls
Your AppleVision monitor comes with a set of onscreen controls you use to
adjust the screen image.
Icon is highlighted to show
the menu you’ve selected
Indicates the topic
you’ve selected
-
+
Shows the current value of
the topic you’ve selected
Use the buttons on the front of your monitor to open the Monitor Controls
window and select topics from the menus.
Press any button to
open the Monitor
Controls window.
Press o or ø to select a
menu. Icons on screen are
highlighted to show the
menu you’ve selected.
58
Chapter 4
Press to choose a topic
from a menu. An arrow
appears next to the
topic you’ve selected.
Sets a value for the selected
topic. Press – to decrease
value. Press + to increase
value.
Adjusting screen geometry
Select to show the
Geometry menu.
-
+
Use the Geometry menu to adjust the height and width of the screen image,
center the image on the screen, and so on.
Width
Adjusts the width of the screen image. Press – to decrease width. Press + to
increase width. When the width and height of the screen image are set
properly, you can see the entire image on the screen.
Height
Adjusts the height of the screen image. Press – to decrease height. Press + to
increase height. When the height and width of the screen image are set
properly, you can see the entire image on the screen.
Pincushion
Adjusts the shape of the screen image. Press – to bring in the sides of the
image, changing the shape from convex to concave. Press + to expand the
sides of the image, changing the shape from concave to convex. When the
shape of the image is set properly, the left and right sides are straight and the
image is rectangular.
Vertical Shift
Adjusts the vertical position of the screen image. Press – to move the image
down. Press + to move the image up. When the screen image is centered
properly, there is an equal border around all edges of the image.
Using Your Monitor With Windows-Based Computers
59
Horizontal Shift
Adjusts the horizontal position of the screen image. Press – to move the image
to the left. Press + to move the image to the right. When the screen image is
centered properly, there is an equal border around all edges of the image.
Rotate
Rotates the screen image. Press – to rotate counterclockwise. Press + to rotate
clockwise. When the rotation of the screen image is set properly, all four sides
of the image are parallel to the edges of the screen and the image is
rectangular.
Default
Returns screen adjustments to the preset factory values. Press the + button to
turn defaults on.
Adjusting color settings and other features
Select to show the
Tools menu.
-
+
Use the Tools menu to set color temperature, turn overscan on and off, display
the scan rate of your monitor, manually degauss, and turn speakers on or off
in sleep mode.
60
Chapter 4
Color Temperature
Adjusts the color temperature of your monitor. The color temperature (or
white point) you select for your monitor sets the mix of red, green, and blue
light that makes the color white. This color temperature sets the foundation
for other colors on your monitor.
The color temperature of your monitor can be changed to one of the
following Kelvin temperatures: 4100 K, 5000 K, 6500 K, 7500 K, or 9300 K.
(Kelvin is a temperature scale used in scientific applications.)
Press – to decrease color temperature. Press + to increase color temperature.
Changing the color temperature changes the appearance of colors on the
screen. Lower temperature settings create reddish whites, and higher
temperature settings create bluer whites.
Overscan
Turns overscan on and off. Overscan moves the screen image as far to the
edges of the screen as possible without distorting the image. Press – to turn
overscan off. Press + to turn overscan on.
When overscan is on, you cannot make screen geometry adjustments such as
horizontal shift, rotation, and so on.
Scan Rate
Shows the scan rate of the AppleVision 850 and 850AV. This setting is for
informational purposes only; it’s not for adjusting the scan rate.
Degauss
Manually degausses the monitor. Press + to degauss the monitor.
Audio Power Saver
Turns speakers on or off in sleep mode. Press + to activate Audio Power
Saver, which will turn monitor speakers off in sleep mode. Press – to leave
monitor speakers on in sleep mode. (This feature is only available on the
AppleVision 850AV Display.)
Using Your Monitor With Windows-Based Computers
61
Adjusting convergence
Select to show the
Convergence menu.
-
+
Red, green, and blue signals in your monitor converge to create the colors you
see on your screen. If the convergence is not set properly, images or text on
your screen may appear blurred, or you may get a “rainbow” effect with
several colors forming the edges of images on the screen.
If your monitor is exposed to an external electromagnetic field (for example,
from another monitor) over a period of time, you may need to change the
convergence to get a clear, distinct screen image.
Use the Convergence menu to adjust screen convergence. When convergence
is set properly, the image is clear and distinct.
Vertical
Adjusts the vertical convergence. Press – to move the red signal down and the
blue signal up. Press + to move the red signal up and the blue signal down.
Horizontal
Adjusts the horizontal convergence. Press + to move the red signal to the left
and the blue signal to the right. Press – to move the red signal to the right and
the blue signal to the left.
62
Chapter 4
Adjusting sound on your AppleVision 850AV Display
Use the sound control buttons to adjust the volume, bass, treble, and mute
options on your AppleVision 850AV Display. (These features are not available
on the AppleVision 850 Display.)
O
¤
®
AppleVision
850AV Display
Z
Bass controls
Press ¿ to increase bass;
press ÷ to decrease bass.
Microphone button
Press to turn the monitor’s
built-in microphone on or off.
Treble controls
Press ¿ to increase treble;
press ÷ to decrease treble;
press both to turn 3D sound
on or off.
Mute button
Press to turn
mute on or off.
Volume controls
Press ¿ to increase volume;
press ÷ to decrease volume.
Tips for using sound controls
m For best results, adjust the volume on your computer first. Then, use the
sound controls to adjust the volume on your monitor.
m Using the microphone button, turn off the monitor’s built-in microphone to
activate other equipment (an audio CD player, for example) connected to
the sound input port on your AppleVision monitor.
Using Your Monitor With Windows-Based Computers
63
5
Tips and Troubleshooting
This chapter includes information on the care and cleaning of your monitor,
protecting your monitor from theft, and troubleshooting.
Care and cleaning
m Do not block the monitor’s vents.
m Do not let liquid get on or into the monitor.
m If you will not be using your monitor and computer for a long period of
time (a day or more), make sure you turn off the computer (and your
monitor, if necessary).
To clean the case and screen of the monitor:
1
Turn your computer and monitor off.
2
Disconnect the monitor’s power cord.
If the monitor’s power cord is connected to a grounded wall outlet, disconnect
the power plug from the outlet.
If the monitor’s power cord is connected to the back of your computer,
disconnect the monitor’s power plug from the back of the monitor.
3
Wipe the case surfaces lightly with a clean, soft cloth dampened with water.
Don’t use aerosol sprays, solvents, or abrasives that might damage the finish
on the case.
65
4
Use a mild, non-abrasive cleaner on a soft cloth and wipe the screen. Don’t spray the
cleaner onto the screen, because the liquid may drip inside the monitor.
WARNING Do not use a cleaner that contains alcohol or acetone. You
might damage the screen.
Protecting your monitor from theft
The slot at the base of the monitor in the back is for connecting a security
lock. It lets you attach a narrow, flexible cable that you can use to secure your
monitor (and the rest of your computer system) to prevent theft. Security
locks are available from an Apple-authorized dealer or service provider.
Troubleshooting common problems
This section contains descriptions of problems you might experience with
your monitor as well as solutions to try. Problems related to the computer
itself are covered in the manuals that came with your computer.
WARNING Never remove the cover from the monitor or you may come in
contact with hazardous voltage levels capable of causing serious injury
and possibly death.
WARNING If you have a problem with your monitor and nothing
presented in this manual or in Apple Guide solves it, consult the service
and support information that came with your monitor for instructions on
how to contact an Apple-authorized service provider or Apple for
assistance. If you attempt to repair the monitor yourself, any damage
you may cause to the monitor will not be covered by the limited
warranty on your monitor. Contact an Apple-authorized dealer or
service provider for additional information about this or any other
warranty question.
66
Chapter 5
Monitor power and screen appearance
IMPORTANT Detailed instructions for AppleVision software are provided in
Macintosh Guide (called Mac OS Guide on some computers) and in Monitors
& Sound Guide. System 7.1 users can view AppleVision software instructions
in Adobe Acrobat Reader by opening the Monitors & Sound doc.pdf file
(located in the AppleVision Extras folder). For Windows users, detailed
instructions about onscreen controls are provided in Chapter 4, “Using Your
Monitor With Windows-Based Computers.”
The monitor’s power indicator light doesn’t come on.
m Make sure the monitor power button is turned on.
m Make sure the computer is turned on.
The monitor’s power indicator light won’t turn green unless your computer
is on.
m Make sure an energy saver program isn’t active on the computer.
The monitor’s indicator light is amber when an energy saver program is on.
Also, it may take some time to wake up your computer after you use an
energy saver.
m Make sure the power cord is plugged in properly.
If the monitor power cord is plugged into your computer, make sure your
computer is on and the cord is firmly plugged in.
If the monitor power cord is plugged into a grounded wall outlet, make sure
the cord is firmly plugged in. Check to see whether power to the outlet has
been interrupted. You can test the outlet by plugging in something that you
know works—like a desk lamp or radio. If the test appliance works, but the
monitor doesn’t, contact an Apple-authorized dealer or service provider.
m Make sure the monitor cable is connected to your computer properly.
m Make sure the thumbscrews on the monitor cable are tightened securely.
Tips and Troubleshooting
67
No image appears on the screen and the monitor’s power indicator light is on.
m Make sure the monitor cable is connected correctly to the computer.
m Make sure the thumbscrews on the monitor cable are tightened securely.
m Make sure the contrast (O) and brightness (¤) controls are set correctly.
The contrast and brightness controls are on the front of your monitor.
m Restart your computer, holding down x-Option AV. This resets the monitor
to factory default settings.
The screen is dark or appears dim.
m Make sure that your computer and monitor are turned on.
m Make sure that the power cord and the monitor cable are securely
connected at both ends.
m Increase the contrast and brightness of the screen image. The contrast (O)
and brightness (¤) controls are on the front of your monitor.
m A screen saver that darkens your screen may be activated. Press any key on
the keyboard to reactivate the monitor.
m On Mac OS–based computers, the Energy Saver option may be activated.
Press any key on the keyboard to reactivate the monitor. In approximately
10 seconds, the monitor is reactivated.
Over time, you experience eyestrain.
m Adjust the screen contrast. In a bright room, contrast is usually best set at
maximum; in a dim room, lower contrast is usually more comfortable. The
contrast (O) controls are on the front of your monitor. Also, be sure to take
occasional breaks to focus your eyes on a distant object.
m Adjust the color temperature or white point of the screen image. For most
application programs, a white point of 9300 K is best. For Mac OS–based
computers, click the Color button in the Monitors & Sound control panel
and set a new white point. For Windows-based computers, open the Tools
menu, select Color Temperature, and set a new white point.
68
Chapter 5
Contrast (O) and brightness (¤) controls on the front of the monitor don’t appear
to work.
m For Mac OS–based computers, your monitor may have the contrast (O)
and brightness (¤) controls disabled. Click the Color button in the
Monitors & Sound control panel and select Preferences. Under Calibration
Protection, make sure that the checkbox to disable contrast and brightness
controls is not marked; then, click OK.
The screen doesn’t dim when Energy Saver or other energy-saving software is on.
m Make sure the energy-saving software is installed properly and the amount
of time you’ve set up to trigger it has passed. For Mac OS–based
computers, see “Conserving Energy” in Chapter 2 for more information.
For Windows-based computers, see the manual that came with your
energy-saving software.
The screen flickers.
m Make sure the monitor cable is connected firmly to the correct port on the
back of the computer.
m The flickering could be caused by interference from a nearby power line
or electrical equipment—for example, a radio, a microwave oven, or
another computer. Try relocating nearby electrical equipment, or moving
your computer and monitor.
m If you have more than one monitor attached to your computer, the monitors
might be interfering with one another. Make sure you’re using a shielded
ADB connector cable. Move the monitors farther apart or set the monitors
at an angle, so their screens are close and their back panels are farther
apart. If, after moving the monitors more than 16 inches apart, you still see
flickering, contact an Apple-authorized dealer or service provider.
m If you are using a video card that has a very low refresh rate (below 67 Hz),
the monitor may flicker. You may be able to change the refresh rate for the
card. If possible, use a 75 Hz setting. See the manual that came with your
video card for more information.
Tips and Troubleshooting
69
There are one or two very thin gray lines across the screen, one near the top and the
other near the bottom.
m This is a normal characteristic of the Trinitron color picture tube design.
The lines do not appear in any documents you print.
The screen image is off center.
m Adjust the center of the image. For Mac OS–based computers, click the
Geometry button in the Monitors & Sound control panel and modify the
Position setting. For Windows-based computers, select the Geometry
menu; then, click Vertical Shift. Press – to move the screen down and + to
move the screen up. Repeat the process for Horizontal Shift.
The screen image is tilted slightly to the left or right.
m Adjust the rotation of the screen image. For Mac OS–based computers,
click the Geometry button in the Monitors & Sound control panel and
modify the Rotate settings. For Windows-based computers, select the
Geometry menu; then, click Rotate. Press – to rotate counterclockwise and
+ to rotate clockwise.
The screen image is too large or too small.
m Adjust the horizontal or vertical size of the screen image. For
Mac OS–based computers, click the Geometry button in the Monitors &
Sound control panel and modify the height/width settings. For Windowsbased computers, select the Geometry menu; then, click Width. Press – to
decrease width and + to increase width. Repeat the process for Height.
m Make sure overscan is off. For Mac OS–based computers, click the
Geometry button in the Monitors & Sound control panel and select Off
for overscan. For Windows-based computers, select the Tools menu; then,
click overscan. Press – to turn off overscan.
m Try changing to another resolution. For Mac OS–based computers, click
the Monitor button in the Monitors & Sound control panel and select
another resolution. For Windows-based computers, see the manual that
came with your computer or video card.
70
Chapter 5
Images or text on your screen appear fuzzy or blurred.
m Adjust the horizontal or vertical convergence of the screen image. For
Mac OS–based computers, click the Geometry button in the Monitors &
Sound control panel and select Convergence to change settings. For
Windows-based computers, select the Convergence menu; then, click
Vertical. Press – to move the red signal down and the blue signal up. Press
+ to move the red signal up and the blue signal down. Then, click
Horizontal. Press – to move the red signal to the right and the blue signal
to the left. Press + to move the red signal to the left and the blue signal to
the right.
The colors on your screen appear too blue, too yellow, or too red.
m Adjust the color settings, recalibrate the monitor, set a new white point, or
reset the monitor to the default factory color settings. For Mac OS–based
computers, click the Color button in the Monitors & Sound control panel
to open color controls. For Windows-based computers, see “Adjusting
Color Settings and Other Features” in Chapter 4 for more information.
The screen appears greenish, the screen image is blank or unreadable, or there is
“snow” on the screen.
m Make sure the monitor cable is connected firmly to the correct port on the
back of the computer.
There are wavy lines on the screen, creating an optical effect or moiré pattern.
m You may see a moiré pattern while in some resolutions, depending on the
desktop pattern displayed on the screen (the black-and-white checkerboard
pattern frequently causes moiré). For Mac OS–based computers, click the
Monitor button in the Monitors & Sound control panel and change to
another resolution. For Windows-based computers, see the manuals that
came with your computer. To change the desktop pattern, see the manuals
that came with your computer or, for Mac OS–based computers, also see
Macintosh (or Mac OS) Guide for more information.
Your application program doesn’t recognize changes you make in resolution settings.
m Some application programs do not properly support resolution changes you
make to your monitor. You may have to close and restart your program for
it to recognize the resolution changes.
Tips and Troubleshooting
71
Sound on your AppleVision 850AV Display
IMPORTANT Detailed instructions for AppleVision software are provided in
Macintosh Guide (called Mac OS Guide on some computers) and Monitors &
Sound Guide. System 7.1 users can view AppleVision software instructions in
Adobe Acrobat Reader by opening the Monitors & Sound doc.pdf file
(located in the AppleVision Extras folder). For Windows users, detailed
instructions about sound controls are provided in Chapter 4, “Using Your
Monitor With Windows-Based Computers.”
You don’t hear a system beep when you start up your computer.
m Plug your monitor into the wall outlet, not the back of your computer.
m Adjust the volume level on your speakers.
m For Mac OS–based computers, disable the audio energy-saving feature in
the Monitors & Sound control panel. Click the Preferences button in the
Monitor Sound window; then leave the option, “Turn Speakers Off in
Energy Saver Mode,” unchecked.
You don’t hear any sound on your AppleVision 850AV speakers or headphones.
m Increase the volume. Make sure the volume controls in your computer are
set correctly first. Then use the audio controls on the front panel of the
AppleVision monitor to increase the speaker volume. For Mac OS–based
computers, click the Sound button in the Monitors & Sound control panel
and adjust the volume on your computer; then click the Monitor Sound
button and adjust the monitor speaker or headphone volume. For
Windows-based computers, see Chapter 4 and the manuals that came with
your computer.
m If you have an audio CD player connected to the sound input port on your
monitor, make sure the volume on the audio CD player is set above
minimum. For Mac OS–based computers, make sure you’ve selected “line
level.” Open the Monitor Sound window of the Monitors & Sound control
panel; then, adjust the sound input Port Gain to “line level.”
72
Chapter 5
m If you have sound input equipment connected to your monitor, make sure
the correct sound input setting is selected on your computer. For Mac
OS–based computers, see Chapter 3, “Using Sound and Video With Your
AppleVision 850AV Display,” for more information. For Windows-based
computers, see the manuals that came with your computer for more
information.
m For Mac OS–based computers, if headphones are connected, but you still
want to play sound on your AppleVision 850AV speakers, make sure “Mute
speakers when headphones are connected” isn’t checked in the Preferences
window. To open Preferences, click the Monitor Sound button in the
Monitors & Sound control panel and choose Preferences.
m Check Routing to make sure that the correct configuration is selected.
Click the Monitor Sound button in the Monitors & Sound control panel;
then, click Routing. Choose Computers and Speakers; then, click OK.
m Make sure the sound cable is plugged into the computer and monitor
properly.
m For an internal CD, make sure you’ve selected the correct sound input
settings. In the Monitors & Sound control panel, click the Sound button
and choose the appropriate sound input device.
m Make sure the headphones are securely connected to the monitor’s sound
output port (marked by f).
Headphone volume is low.
m Make sure the headphone volume is set to maximum. For Mac OS–based
computers, click the Monitor Sound button in the Monitors & Sound
control panel and adjust headphone volume. For Windows-based
computers, see “Adjusting Sound on Your AppleVision 850AV Display” in
Chapter 4 for more information.
m Make sure the volume controls on your computer are set correctly. For
Mac OS–based computers, click the Sound button in the Monitors &
Sound control panel and adjust computer speaker volume. For Windowsbased computers, see the manuals that came with your computer for
more information.
Tips and Troubleshooting
73
The internal microphone doesn’t record.
m Turn on the microphone by pressing the microphone button (marked by Z)
on the front of your monitor. When the microphone is on, the microphone
indicator light is on.
m For Mac OS–based computers, after you have pressed the microphone
button on the monitor, make sure you’ve selected the internal microphone
as the sound input source in the Sound window of the Monitors & Sound
control panel.
m Make sure the monitor’s sound cable is connected properly. See
“Connecting Sound Equipment to Your AppleVision 850AV Display” in
Chapter 1.
The microphone button on your keyboard doesn’t turn on your monitor microphone.
m Some adjustable keyboards for Mac OS–based computers have a button
marked by Z. This button does not turn on the built-in microphone on
your AppleVision 850AV Display. Instead, use the microphone button
(marked by Z) on the front of the monitor.
You can still hear internal computer speakers when playing sound on the AppleVision
850AV speakers.
m On some computers, you must manually mute the internal computer
speakers. Click the Sound button in the Monitors & Sound control panel;
then make sure that mute is selected in the Computer System Volume
dialog box. See Macintosh (or Mac OS) Guide or the manuals that came
with your computer for more information.
AppleVision 850AV speakers don’t mute when headphones are connected.
m Make sure “Mute speakers when headphones are connected” is selected in
the Preferences dialog box. Click the Monitor Sound button in the
Monitors & Sound control panel; then, click Preferences.
Playback doesn’t work on your AppleVision monitor.
m Some third party sound cards do not support simultaneous input and
output, meaning playback won’t work if the AppleVision monitor is
plugged into both ports. If this happens, unplug one port in order to make
the other port work. See the information that came with your sound card or
computer for more information.
74
Chapter 5
An external microphone connected to the sound input port (marked by ≈) on the monitor
doesn’t record quality sound.
m For Mac OS–based computers, you may need to adjust the Gain for the
microphone. Click the Monitor Sound button and adjust the Gain for
the microphone.
m Some external microphones don’t work well with the AppleVision 850AV
Display. Use the monitor’s built-in microphone, or plug the external
microphone directly into the sound input port on the back of your
computer.
m If you’re using the AppleVision 850AV Display with another monitor that
records sound, turn off the microphone on the other monitor. With both
microphones on, you may get feedback or other interference.
Selecting Mute in an application program’s window doesn’t mute sound coming from
the monitor.
m For Mac OS–based computers, some programs cannot mute sound coming
from the AppleVision 850AV Display. To mute the sound, select Mute
Monitor Sound in the Monitor Sound window of the Monitors & Sound
control panel.
Your third party driver no longer shows up in your Monitors & Sound control panel.
m Some Mac OS–based sound drivers require the Sound control panel, an
older control panel that has been replaced on your computer by the
Monitors & Sound control panel. You can reinstall the Sound control
panel. Open the Apple Extras folder on your hard disk and double-click the
AppleVision Extras folder. Double-click the Sound control panel icon.
Tips and Troubleshooting
75
Monitors & Sound control panel for Mac OS–based computers
IMPORTANT Detailed instructions for AppleVision software are provided in
Macintosh Guide (called Mac OS Guide on some computers) and Monitors &
Sound Guide. System 7.1 users can view AppleVision software instructions in
Adobe Acrobat Reader by opening the Monitors & Sound doc.pdf file
(located in the AppleVision Extras folder).
The name of your monitor doesn’t appear in the Monitors & Sound control panel.
m After you set up your AppleVision monitor, make sure the monitor power
is on and restart your computer.
m Make sure the ADB connector on the monitor cable is plugged directly into
your computer’s ADB port.
m Make sure you’ve installed the AppleVision software that came with
your monitor. See “Installing AppleVision Software” in Chapter 2 for
more information.
m You may be using a video card that’s not compatible with your monitor.
Contact the manufacturer of the video card for information.
A message appears, “This version of system software is not supported by the
AppleVision software.”
m Make sure you’re using System 7.1 or later.
m If this message appears in the AppleVision software installer, make sure
you select the startup hard disk in the Installation dialog box.
A message appears, “The AppleVision preferences are invalid and may have
become corrupted.”
m Delete the AppleVision Preferences folder on your hard disk and restart
your computer.
A message appears, “An error has occurred reading from or writing to a file.”
m Make sure you are not starting up from a non-writable disk, such as a CD,
a locked hard drive, or a floppy disk.
76
Chapter 5
A message appears, “This monitor is not supported by this version of the
AppleVision software.”
m Make sure you have installed the AppleVision software that came with your
monitor. See Chapter 2, “Installing and Using AppleVision Software,” for
more information.
A message appears, “AppleVision failed to load,” followed by an error code.
m Make sure you’ve plugged the monitor connector and ADB connector on
the monitor cable into the correct ports. You may have plugged them into
the wrong ports by mistake. See “Connecting the Monitor Cable to a
Mac OS–based Computer” in Chapter 1 for more information.
m Make sure your video card supports the AppleVision monitor. See the
manual that came with your video card or computer.
m Some viruses can cause problems with the AppleVision software. Make
sure you regularly scan your computer for viruses.
m If AppleVision software is installed and you start up your computer
holding down the Shift key, the Display Enabler extension will not load
and the software will not run. Restart your computer without disabling
extensions to use the AppleVision software.
m If none of the suggestions solves the problem, reinstall the AppleVision
software.
The Monitors & Sound control panel opens, but does not include the Geometry, Color, or
Monitor Sound buttons.
m Make sure the ADB connector on the monitor cable is plugged directly into
your computer’s ADB port.
m Reinstall the AppleVision software that came with your computer.
See Chapter 2, “Installing and Using AppleVision Software,” for
more information.
ColorSync Profile files are not updated when ColorSync is installed.
m Out-of-date profiles in the ColorSync Profiles folder are not removed
automatically. If you want to remove a ColorSync profile, you must do so
manually. See Appendix A, “Using ColorSync,” for more information
about ColorSync.
Tips and Troubleshooting
77
Your AppleVision monitor appears as a VGA monitor in the Control Strip pop-up menus.
m Make sure the ADB connector on the monitor cable is plugged directly into
your computer’s ADB port.
m Reinstall the AppleVision software that came with your computer.
See Chapter 2, “Installing and Using AppleVision Software,” for
more information.
You hear no alert sound.
m Make sure the alert volume control is set correctly. Click the Alerts button
in the Monitors & Sound control panel and reset the System Alert Volume.
Changes in the Monitors & Sound control panel don’t work for the monitor.
m Make sure you have installed the AppleVision software that came with
your monitor.
m Because each monitor connected to your computer has its own Monitors &
Sound window, use the window that displays the name of your
AppleVision monitor in the top-left corner.
When you open the Monitors & Sound control panel, only one resolution is available.
m Make sure you have connected the ADB connector to your computer. You
cannot use many of the features of the AppleVision software without an
ADB connection. See “Connecting the Monitor Cable to a Mac OS–Based
Computer” in Chapter 1 for more information.
m If AppleVision software is installed and you start up your computer
holding down the Shift key, the Display Enabler extension will not load
and the software will not run. Restart your computer without disabling
extensions to use the AppleVision software.
m Reinstall the AppleVision software that came with your computer.
See Chapter 2, “Installing and Using AppleVision Software,” for more
information.
When you turn on overscan, it stays on even when you change resolutions.
m This is a new feature of the AppleVision 850 and 850AV. In other
AppleVision monitors, overscan will automatically turn off when you
change resolution settings.
78
Chapter 5
No colors appear on the screen.
m Check to make sure that the number of colors is set correctly in the Control
Strip or in the Monitors & Sound control panel.
No colors appear when you create a custom white point.
m Make sure the color depth on your monitor is set to Thousands of Colors or
Millions of Colors. Click the Monitor button in the Monitors & Sound
control panel and reset the color depth, or use the Control Strip to
change settings.
You do not have a CD-ROM disc drive for installing the AppleVision software.
m You can order a set of floppy disks of the AppleVision software. See the
service and support information that came with your monitor for more
information. Support information and Apple software updates are also
available via Apple’s World Wide Web sites: http://www.info.apple.com and
http://www.support.apple.com.
Tips and Troubleshooting
79
Appendix A
Using ColorSync
Mac OS–based computers use ColorSync to help make sure that the colors
you see on your monitor closely match the colors you get on your printers,
scanners, and other devices. Because ColorSync works behind the scenes, you
don’t have to know anything about it. All you need to do is initially set it up.
This appendix describes how ColorSync works and how to configure your
monitor and computer to take advantage of it.
The problem that ColorSync solves
Providing consistent color with desktop computers is a technical challenge
because different color devices use different methods for representing color,
and they produce different ranges of colors. For example, the colored light on
your monitor is very different from the colored inks your printer uses.
Different color devices also create color using different methods. Monitors
(and most scanners) produce colors by mixing red, green, and blue light—
called RGB color. Most printers produce colors by mixing cyan (a shade of
blue), magenta (a bright pink), yellow, and black ink. This color system is
called CMYK. Since monitors, printers, and scanners each have different color
capabilities, they cannot reproduce each other’s colors exactly.
81
Further compounding the problem is that no two monitors or printers produce
exactly the same colors. (For example, you can see differences in color ability
among monitors in the TV department of a consumer electronics store.)
ColorSync is a system extension that provides color-conversion capabilities and
improves color consistency. ColorSync “translates” the colors used on one
device so that they more closely match the colors displayed or printed on
another device.
ColorSync color conversion is a central part of Mac OS–based computing,
ensuring that applications, monitors, printers, scanners, and digital cameras can
use the same scheme for color conversion. This means you can scan an image,
display it on your monitor, and print it—with visually matching colors every
step of the way.
How ColorSync works
When you create a TIFF or PICT file using a program that supports ColorSync,
a “profile” describing the color capabilities of your equipment is saved with the
image. For example, when you scan a photograph, a profile describing the
scanner is saved inside the image file. If you later print the image, even using a
different computer, ColorSync looks at the profile to learn about the
capabilities of the scanner you used, and automatically picks closely matching
colors that your printer can reproduce.
The profile contains information ColorSync needs to perform color matching,
such as the lightest and darkest possible tones (white point and black point)
that the device can produce, and the maximum supported densities for red,
green, blue, cyan, magenta, and yellow. Together, these characteristics describe
the color gamut (or range) that a device is capable of capturing, displaying,
or reproducing. To take advantage of ColorSync, each of the imaging devices
you use needs to have its own ColorSync profile. When you create images
using these devices, information from the profile will automatically become
part of the image file—ensuring that colors are consistent throughout the entire
creative process.
82
Appendix A
Because ColorSync information becomes part of your output files, you don’t
have to worry about losing the profile or using the wrong profile with the
wrong image. Additionally, ColorSync profiles are in the standard
International Color Consortium (ICC) format recognized by Microsoft
Windows, Mac OS, and other systems.
When you work with an image that has an embedded ColorSync or ICC
profile, ColorSync identifies the colors that your monitor or printer can
reproduce by examining their ColorSync profile. It compares their capabilities
with those of the system used to create the image (as described in the
embedded profile), and then picks appropriate, matching colors. For example,
your monitor may be able to display a vivid red, but your printer inks may not
be able to produce that color. ColorSync determines the “next best” color for
your printer to use.
Monitor
Printers
ColorSync profile
ColorSync
Digital cameras
Scanners
ColorSync performs color matching by comparing each profile to an
independent color standard. ColorSync uses the CIE color standard, which
describes colors in terms of how they are perceived by the human eye under
specific lighting conditions. (CIE stands for the Commission International de
l’Eclairage, the International Commission on Illumination, which created the
standard in 1931.)
Using ColorSync
83
Setting up ColorSync
To take advantage of ColorSync, you need to obtain profiles for each of your
imaging devices, such as your monitor, scanner, and color printer. ColorSync
profiles are usually automatically installed when you install the software for a
ColorSync-supported device. Profiles are stored in the ColorSync Profiles
folder, inside Preferences in the System Folder. If you need to obtain a
ColorSync profile, contact the manufacturer of your device. Ask for either a
ColorSync or ICC profile for the specific model of monitor, printer, or
scanner you’re using.
You also need to make sure the ColorSync extension is installed and active.
ColorSync is automatically installed in the Extensions folder of your System
Folder during AppleVision software installation. Unless you’ve removed or
disabled it, it’s already installed.
Finally, you need to set a ColorSync System Profile for the Mac OS. The
ColorSync System Profile is used by ColorSync to determine the color range
of your monitor. ColorSync compares this information with the profiles of
your other devices to make sure that colors are consistent with what you see
on your monitor.
Additionally, the System Profile is used as a default profile if a document you
are working on doesn’t have any ColorSync information saved within it. This
can occur if the document was created without ColorSync installed. By using
the System Profile as a default, ColorSync ensures that colors are consistent
with what you currently see on your monitor.
84
Appendix A
Setting the ColorSync System Profile
To set the System Profile, follow these steps:
1
Make sure the profile you want to use is located in the ColorSync Profiles folder.
This folder is located in the Preferences folder in your System Folder.
2
Choose Control Panels from the Apple (K) menu and open the ColorSync System Profile
control panel.
The ColorSync System Profile control panel appears.
3
Click Set Profile.
A dialog box appears with a list of ColorSync profiles installed on
your computer.
4
Click the profile you want to use or create your own custom profile.
Note: The profile names may appear different on your screen.
Select the profile for the AppleVision 850 monitor. If you’ve created a custom
ColorSync profile that describes your color settings, select it as the system
profile instead. See Monitors & Sound Guide or the Monitors & Sound
doc.pdf file for more information on creating custom ColorSync profiles.
Using ColorSync
85
5
Click Select.
ColorSync automatically references the profile you selected and uses it to
define the color capabilities of your monitor.
6
Close the ColorSync System Profile control panel.
Setting other ColorSync profiles
Some programs and printer software might require that you do something
special, such as turning on an option, in order to take advantage of ColorSync.
For example, to use ColorSync with the Apple Color OneScanner, select the
Use ColorSync option in the ColorSync Preferences dialog box of the
OneScanner Dispatcher software. This tells the scanning software to embed
information about the Color OneScanner in scanned images.
Refer to the instructions that came with your application or device to
determine if it supports similar options. If there’s an option to specify a
profile or to activate ColorSync, be sure to use it.
Tips for best results
After you’ve made sure ColorSync is installed, set the System Profile, and set
any necessary ColorSync options for your applications, you’re ready to begin
taking advantage of ColorSync! Just scan, create, and print your images or
documents as you normally would. ColorSync works behind the scenes to
ensure consistent color matching.
The following settings and strategies will help you get the best color results
from your system. Not all of these tips will apply to the software and devices
you may be using, but be sure to take advantage of those tips that do.
m Set the gamma curve for your monitor to 1.8:Standard to have the monitor
more closely match printed results. See Monitors & Sound Guide or the
Monitors & Sound doc.pdf file for more information on gamma settings
available in the Monitors & Sound control panel.
86
Appendix A
m Use the ColorSync System Profile control panel in the Apple (K) menu
to select the AppleVision 9300 profile if your white point is set to
9300 + 8MPCD. If you calibrate your monitor to a white point setting
other than 9300 + 8MPCD, create a custom profile and select it as the
system profile instead. See Monitors & Sound Guide or the Monitors
& Sound doc.pdf file for more information on creating custom ColorSync
profiles.
m Share custom ColorSync profiles describing your AppleVision color
settings with others to help ensure color accuracy for images you
create using your AppleVision monitor. See Monitors & Sound Guide
or the Monitors & Sound doc.pdf file for information on exporting
ColorSync profiles.
m When printing in color, check to see if the printing options include a
setting for ColorSync. For example, for the Apple LaserWriter 12/600 PS,
turn on ColorSync by clicking the Options button and selecting “ColorSync
Color Matching.”
m If your scanning program has a ColorSync option, use it. This embeds a
ColorSync profile within the scanned image file, and ColorSync will be
better able to reproduce the original colors on your monitor and printer.
m Don’t try to use two color-matching systems at once on your computer.
Some applications install other color-matching systems. These should
either be removed or disabled if you want to use ColorSync.
Using ColorSync
87
Appendix B
Technical Information
Picture tube
m 20-inch (19.0-inch diagonal viewable image size) Trinitron CRT
Screen
m Multilayer anti-reflection panel conforms to TCO 92 guidelines
m 0.26 millimeter (mm) stripe pitch
m 0.25 mm grille pitch
Input signals
m Red, green, and blue video signals
m Multiple scan
m DDC clock and data signals
m Vertical Refresh Rate: 48 hertz (Hz) to 120 Hz
m Horizontal Scan Rate: 30 Kilohertz (kHz) to 94 kHz
89
Power-saving and environmental features
AppleVision monitors are equipped with energy-saving features that allow the
monitors to conserve energy when the computer is not in use. The color of
the power indicator light on the front of the monitor indicates the operating
mode:
Mode
Power consumption: watts (W)
Power indicator
Normal
<150 W (850)
<180 W (850AV)
Green
Monitor sleep
<30 W (850 and 850AV)
Orange
System sleep
<5 W (850)
<5 W (850AV with speakers off)
<30 W (850AV with speakers on)
Orange
For instructions on adjusting the system and monitor sleep settings, and
additional energy-conservation information, see “Conserving Energy” in
Chapter 2. System 7.5 (or later) users should also see Macintosh Guide (also
called Mac OS Guide).
m TCO 92 compliant
This product has been certified by TCO (the Swedish confederation of
Professional Employees) to meet global standard safety tests and have
energy-saving features such as automatic monitor power down and reduced
electromagnetic fields.
m MPR II compliant to ensure reduced electromagnetic and
electrostatic emissions
m Energy Star compliant
This product complies with the United States Environmental Protection
Agency’s Energy Star criteria for energy-efficient office products. The EPA
Energy Star Office Equipment program is a partnership program to
promote energy-efficient personal computers, monitors, printers, fax
machines, and copiers. Reducing the energy consumption from this
equipment can help combat smog, acid rain, and climate change by
decreasing emissions from electricity generation.
m DPMS compliant
90
Appendix B
This product’s power-saving features comply with the Video Electronics
Standards Association (VESA) Display Power Management Standard (DPMS).
(Connected CPU must also be VESA DPMS compliant to use DPMS features.)
User controls
m Power-on button
m Automatic degauss at startup; manual degauss by turning power switch off,
then on
m Control buttons: contrast, brightness, and five buttons for
onscreen controls
m Audio control buttons for AppleVision 850AV Display: bass, treble,
microphone on, volume, and mute
m Additional picture and sound controls available using the Monitors &
Sound control panel (Mac OS–based computers) or onscreen controls
(Windows-based computers)
Factory preset timings
m Adjusted at the factory for the following standard modes:
Mode
Resolution
Vertical refresh rate
(hertz)
Horizontal scan rate
(kilohertz)
VGA
640 x 480
60
31.469
Macintosh
640 x 480
67
35.036
VESA
640 x 480
72
37.861
VESA
640 x 480
75
37.500
VESA
640 x 480
85
43.269
VESA
800 x 600
56
35.160
VESA
800 x 600
60
37.879
VESA
800 x 600
72
48.077
VESA
800 x 600
75
46.875
VESA
800 x 600
85
53.674
Macintosh
832 x 624
75
49.700
IBM
1024 x 768
87 Int
35.522 interlaced
continued .
Technical Information
91
Mode
Resolution
Vertical refresh rate
(hertz)
Horizontal scan rate
(kilohertz)
VESA
1024 x 768
60
48.363
VESA
1024 x 768
70
56.476
VESA
1024 x 768
75
60.023
VESA
1024 x 768
85
68.677
Macintosh
1152 x 870
75
68.700
VESA
1280 x 1024
75
79.976
VESA
1280 x 1024
85
91.146
VESA
1600 x 1200
75
93.750
Audio input signals for AppleVision 850AV Display
m Accepts audio signal of up to 4 Vpp (line level–low sensitivity) or as low
as 4.4 mVpp (microphone level–high sensitivity) without clipping the
signal, depending upon the level and sensitivity setting
Microphone for AppleVision 850AV Display
m Directional, optimized for use in speech recognition and other voicerelated application programs
Speakers for AppleVision 850AV Display
m Stereo, with ported (bass reflex) chamber design
m Speaker SPL output: > 90 decibel (dB) SPL at 1 kHz at 0.5 meters
m Frequency response: 80 Hz to 17 kHz ± 6 dB
Spatial enhancements and 3D sound features of AppleVision 850AV speakers
m Single channel driven by 2 Vpp, 1 kHz input at external jack
m Output voltage at other channel > 0.38 VRMS (measured at output of
spatial effect enhancement IC).
Headphone jack for AppleVision 850AV Display
m Maximum output level (2 Vpp line level input):
92
Appendix B
Into 600 ohm (Ω) load
> 0.50 volts (v) RMS
Into 10 Kilohm (kΩ) load
> 0.55 v RMS
Input electrical requirements
m Voltage:
90-264 V
m Frequency:
47-63 Hz
m Power:
AppleVision 850
150 W maximum
AppleVision 850AV
190 W maximum
Weight
m AppleVision 850 Display: Approximately 67 pounds (30 kilograms)
m AppleVision 850AV Display: Approximately 77 pounds (35 kilograms)
Dimensions of AppleVision 850 Display
m Height
474 millimeters (mm) ± 3 mm
m Width
484 mm ± 3 mm
m Depth
(not including cables)
515 mm ± 3 mm
Dimensions of AppleVision 850AV Display
m Height
553 millimeters (mm) ± 3 mm
m Width
484 mm ± 3 mm
m Depth
(not including cables)
545 mm ± 3 mm
Interfaces for AppleVision 850 Display
m Apple Desktop Bus (ADB): Two ADB pass-through output ports
Interfaces for AppleVision 850AV Display
m Apple Desktop Bus (ADB): Two ADB pass-through output ports
m Microphone: One input port and one built-in microphone
m Headphone/Speaker: Built-in speakers
Color compatibility
m Works with ColorSync 2.1 or later. ColorSync profiles are compatible with
the profile specifications of the International Color Consortium (ICC).
Technical Information
93
Temperature
Celsius (C) and Fahrenheit (F)
m Operating
10˚ to 40˚ C (50˚ to 104˚ F)
m Storage
0˚ to 60˚ C (32˚ to 140˚ F)
m Shipping
–40˚ to 60˚ C (–4˚ to 140˚ F)
Humidity (noncondensing)
m Operating
20% to 95%
m Storage
5% to 95%
m Shipping
5% to 95%
Altitude
m Operating
0 to 10,000 feet (ft.)
0 to 3048 meters (m)
m Shipping
0 to 35,000 ft.
0 to 10,670 m
94
Appendix B
Display cable specifications
m 15-pin miniature D-type connector
8 7 6 5 4 3 2 1
15 14 13 12 11 10 9
Pin
Signal
1
Red video ground
2
Red video
3
Not used
4
ID 1/DDC RTN
5
Green video
6
Green video ground
7
ID 2/DDC SCL
8
DDC 5V
9
Blue video
10
ID 3/DDC SDA
11
Vertical Sync return
12
Vertical Sync
13
Blue video ground
14
Horizontal Sync return
15
Horizontal Sync
Shell
Shield ground
Technical Information
95
VGA adapter specifications
m Standard 15-pin VGA connector
1 2 3 4 5
6 7 8 9 10
11 12 13 14 15
96
Appendix B
Pin
Signal
1
Red video
2
Green video
3
Blue video
4
Monitor ID 2
5
DDC return
6
Red return
7
Green return
8
Blue return
9
DDC 5V
10
Sync return
11
Monitor ID 0
12
SDA (ID 1)
13
Horizontal Sync
14
Vertical Sync
15
SCL (ID 3)
Shell
Shield ground
Can’t Find It? See also Macintosh Guide’s
onscreen index. Open the Guide (h) menu and
choose Macintosh Guide (or Mac OS Guide);
then click the Index button.
Index
A
adapters
for connecting to a composite video
port 47, 48, 50
for connecting to a high-density
port 14
VGA adapter 14, 15, 95
ADB cables 13, 16
ADB connector 5, 7, 13, 16
ADB port
connecting the keyboard to 16
connecting the monitor to 12–13
connecting the mouse to 16
connecting two monitors to 20
location of 5, 7
adjusting monitor sound
Mac OS–based computers 34, 42–44
Windows-based computers 63
adjusting screen images
Mac OS–based computers 32–38
Windows-based computers 58–62
adjusting the screen 10–11
Adobe Acrobat Reader 30–31
Alerts button (Monitors & Sound control
panel, Mac OS) 34
alert sound (Mac OS)
changing 34
troubleshooting 78
altitude requirements 93
amber power indicator light 21
ambient light setting, changing
(Mac OS) 34
angle of the monitor, adjusting 10
Apple-authorized service provider 66
AppleCD Audio Player application
(Mac OS) 53
Apple PlainTalk Microphone 18
AppleVision 850AV Display
adjusting sound on (Mac OS–based
computers) 34, 42–44
adjusting sound on (Windows-based
computers) 63
connecting sound equipment to 17–19
connecting to your computer 11–17
connecting video equipment to (Mac
OS–based computers) 48–51
controlling built-in speakers on (Mac
OS–based computers)
34, 42–44
controlling built-in speakers on
(Windows-based computers) 63
dimensions of 92
illustration of 4, 5
recording videos with (Mac OS–based
computers) 45–52
sound controls on front of 42, 63
specifications for 89–95
97
Can’t Find It?
See also Macintosh
Guide’s onscreen index.
Open the Guide (h)
menu and choose
Macintosh Guide
(or Mac OS Guide);
then click the
Index button.
98
Index
turning speakers on or off in sleep
mode (Mac OS–based
computers) 40
turning speakers on or off in sleep
mode (Windows-based
computers) 60, 61
weight of 9, 92
AppleVision 850 Display
connecting to your computer 11–17
dimensions of 92
illustration of 6, 7
specifications for 89–95
weight of 9, 92
AppleVision setup information for
Windows 95 operating system
56–57
AppleVision Software CD-ROM disc 25,
30, 57
AppleVision software (Mac OS) 25–40
Control Strip in 36
DigitalColor Meter in 36–37
Energy Saver control panel in 38–40
floppy disk version of 79
installing 25–28
Monitors & Sounds control panel in
33–35, 43–44
onscreen help for 28–30
Pantone Color Picker extension in 38
software license agreement for 26
tips for using 35
using with System 7.1 operating
system 30–31
using with System 7.5 operating
system or later 28–30
Apple World Wide Web sites 23
Arrange button (Monitors & Sound
control panel, Mac OS) 34
audio cable 48, 50
audio CDs, playing (Mac OS–based
computers) 52–53. See also CD
player
audio control buttons 90
audio input signals 91
Audio Power Saver option (Tools menu,
Windows) 61
B
bass, setting
Mac OS–based computers 42, 44
Windows-based computers 63
bass controls 5, 42, 63
blank or unreadable screen 71
blurred images or text 71
brightness
adjusting (Mac OS) 32, 34
adjusting (Windows OS) 57
troubleshooting (Mac OS) 69
brightness controls 5, 7, 32, 57
built-in microphone (AppleVision 850AV
Display)
illustration of 5
as sound input source (Mac OS) 43
specifications for 91
troubleshooting 74
turning on and off (Mac OS–based
computers) 42
turning on and off (Windows-based
computers) 63
built-in speakers (AppleVision 850AV
Display)
adjusting sound (Mac OS–based
computers) 34, 42–44
adjusting sound (Windows-based
computers) 63
energy saver mode and (Mac OS) 40
illustration of 4, 5
muting (Mac OS–based computers)
42, 74, 75
muting (Windows-based
computers) 63
playing audio CDs through (Mac
OS–based computers) 52–53
as sound output source
(Mac OS–based computers) 43
specifications for 91
troubleshooting 72, 73, 74
turning on or off in sleep mode
(Mac OS) 40
turning on or off in sleep mode
(Windows) 60, 61
buttons on front of the monitor 32, 42,
57, 63
C
cables
ADB cables 13, 16
audio cable 48, 50
keyboard cable 16
monitor cable 5, 7, 12–15
mouse cable 16
shielded connector cable 20
sound cable 5, 17
video cable 48, 50
case, cleaning 65
cassette player 19, 43
CD player. See also audio CDs
choosing (Mac OS) 34
connecting 19
playing sound through the monitor’s
speakers (Mac OS–based
computers) 52–53
playing sound through the monitor’s
speakers (Windows-based
computers) 63
as sound input source (Mac OS–based
computers) 43
CD-ROM drive, internal (Mac OS–based
computers) 43, 53
cleaning
case 65
screen 1, 65–66
color
compatibility of 92
consistency of. See ColorSync
depth of, changing (Mac OS)
34, 35, 36
specifying with Pantone Matching
System (Mac OS) 36
troubleshooting 71, 79
white point, setting (Mac OS) 34
white point, setting (Windows) 61
Color button (Monitors & Sound control
panel, Mac OS) 34, 35
color calibration, setting (Mac OS) 34
color conversion 82. See also ColorSync
color settings, adjusting (Mac OS)
34, 35, 36–38
color settings, adjusting (Windows)
60–61
ColorSync (Mac OS) 81–87
how it works 82–83
importing/exporting ColorSync
profiles 34
problem solved by 81–82
setting the ColorSync System Profile
85–86
setting up 84–86
tips for best results with 86–87
ColorSync System Profile control
panel 85
color temperature, setting
Mac OS–based computers 34
Windows-based computers 61
Color Temperature option (Tools menu,
Windows) 61
Communications regulation information
viii
composite video format 45, 46, 47, 48
composite video ports 45, 46, 47, 48
computers. See Mac OS–based
computers; Windows-based
computers
connecting sound equipment to your
AppleVision 850AV Display
17–19
connecting the monitor to your computer
11–17
connecting a Mac OS–based computer
keyboard and mouse to your
monitor 16
connecting the monitor cable to a
Mac–OS based computer 12–14
connecting the monitor cable to a
Windows-based computer 15
connecting the monitor cable to video
connectors 14
connecting the power cord 12
connecting to a standard monitor port
12–13
safety precautions for 11, 13, 47
using more than one monitor 20
Index
99
Can’t Find It?
See also Macintosh
Guide’s onscreen index.
Open the Guide (h)
menu and choose
Macintosh Guide
(or Mac OS Guide);
then click the
Index button.
connectors
ADB connector 5, 7, 13, 16
extended miniplug 18
monitor connector 5, 7, 12–13, 15
sound input and output connectors 17
stereo miniplug 18, 48, 50
S-video connector 47, 48
video connectors 14
conserving energy (Mac OS) 38–40
contrast
adjusting (Mac OS) 32, 34, 68
adjusting (Windows) 57
troubleshooting (Mac OS) 69
contrast controls 5, 7, 32, 57
control buttons
screen control buttons 5, 7, 32, 57, 90
sound control buttons 5, 7, 42, 63, 90
control panels (Mac OS)
ColorSync System Profile control
panel 85
Energy Saver control panel 38–40
Monitors & Sound control panel
33–35, 43–44
controls on screen
Mac OS–based computers 34, 44
Windows-based computers 58–62
Control Strip (Mac OS) 36
convergence, adjusting
Mac OS–based computers 34, 35
Windows-based computers 62
Convergence menu (Windows) 62
D
dark screen 68
Default option (Geometry menu,
Windows) 59
Degauss option (Tools menu,
Windows) 61
diagonal viewable image size 1
DigitalColor Meter (Mac OS) 36–37
dimensions of the monitor 92
dim screen 68
disconnecting power 2
display cable specifications 94
100
Index
E
electrical grounding 11
electrical requirements 92
electrical safety precautions 2–3, 11
electromagnetic emissions 3
Energy Saver control panel (Mac OS)
38–40, 69
environmental features 89
error messages 76–77. See also
troubleshooting
expansion slots 20
exporting ColorSync profile
(Mac OS) 34
extended miniplug 18
external microphone
Apple PlainTalk Microphone 18
choosing with Sound button
(Mac OS) 34
connecting to your monitor 19
as sound input source (Mac OS–based
computers) 43
troubleshooting 75
external speakers
adjusting volume and balance of
(Mac OS) 34
as sound output source (Mac OS) 43
eyestrain 68
F
factory preset timings 68, 90–91
flickering screen 69
fuzzy images or text 71
G
gain level, setting (Mac OS) 44
gamma curve setting, changing
(Mac OS) 34
Geometry button (Monitors & Sound
control panel, Mac OS) 34, 35
Geometry menu (Windows) 59–60
glare on screen 10
green power indicator light 21
grounded outlet 12
grounding 11
H
L
headphone jack 91
headphones
connecting 19
as output source (Mac OS–based
computers) 43
troubleshooting 72, 73, 74
Height option (Geometry menu,
Windows) 59
help 23. See also Monitors & Sound
Guide (Mac OS);
troubleshooting
high-density ports, connecting to 14
Horizontal option (Convergence menu,
Windows) 62
horizontal scan rate 8, 90–91
Horizontal Shift option (Geometry menu,
Windows) 59
humidity requirements 93
line level input port (Windows-based
computers) 17
location for the monitor 9
locking the monitor 66
I, J, K
image options, changing (Mac OS) 34
importing ColorSync profile
(Mac OS) 34
input electrical requirements 92
input signals 89
Installer program (Mac OS–based
computers) 26–27
installing AppleVision software (Mac
OS–based computers) 25–28
interfaces 92
interference viii, 20
keyboard
connecting to the monitor (Mac
OS–based computer) 16
microphone button on (Mac OS–based
computer) 74
M, N
Macintosh Guide 23, 28
Mac OS–based computers
adjusting screen images on monitor
32–38
adjusting sound on AppleVision
850AV Display 34, 42–44
connecting monitor cable to 12–14
installing and using AppleVision
software on 25–40
using on screen controls 34, 44
video card for 9
Mac OS System 7.1, AppleVision
software and 30–31
Mac OS System 7.5 or later, AppleVision
software and 28–30
microphone, built-in (AppleVision 850AV
Display)
illustration of 5
as sound input source (Mac OS–based
computers) 43
specifications for 91
troubleshooting 74
turning on and off (Mac OS–based
computers) 42
turning on and off (Windows-based
computers) 63
microphone, external
Apple PlainTalk Microphone 18
choosing with Sound button
(Mac OS) 34
connecting to your monitor 19
as sound input source 43
troubleshooting 75
microphone button 5, 19, 42, 63
Index
101
Can’t Find It?
See also Macintosh
Guide’s onscreen index.
Open the Guide (h)
menu and choose
Macintosh Guide
(or Mac OS Guide);
then click the
Index button.
102
Index
microphone indicator light 5
monitor cable
connecting to a Mac OS–based
computer 12–14
connecting to a Windows-based
computer 15
connecting to video connectors 14
illustration of 5, 7
monitor connector 5, 7, 12–13, 15
monitor port
on a Mac OS–based computer 12–13
on a Windows-based computer 15
monitors, multiple 20, 34, 44, 69
Monitor Sound button (Monitors &
Sound control panel, Mac OS)
34, 44
Monitors & Sound control panel
(Mac OS)
selecting sound options in 43–44
sound input equipment and 19
third party driver no longer
appears in 75
troubleshooting 76–79
working with 33–35
Monitors & Sound Guide (Mac OS)
28–30
mouse, connecting to the monitor (Mac
OS–based computer) 16
multiple monitors 20, 34, 44, 69
mute button 5, 42, 63
mute indicator light 5
muting sounds 75
muting speakers
Mac OS–based computers 42, 74, 75
Windows-based computers 63
P, Q
O
radio interference viii, 20
RCA plugs 47, 48, 50
recalibrating the monitor (Mac OS) 35
recording sound
Mac OS–based computers 19, 43, 53,
74, 75
Windows-based computers 19, 74, 75
recording videos (Mac OS–based
computers) 45–52
repair 66
resetting the monitor to factory default
settings 68
off-center images on screen 70
online support 23
onscreen controls
Mac OS–based computers 34, 44
Windows-based computers 58–62
overscan
on Mac OS–based computers
34, 35, 78
on Windows-based computers 61
Overscan option (Tools menu,
Windows) 61
Pantone Matching System (Mac OS) 36
picture tube 89
Pincushion option (Geometry menu,
Windows) 59
placement of the monitor 9
playing audio CDs (Mac OS–based
computers) 52–53
playing sound (Mac OS–based
computers) 43
ports
ADB port 12–13, 16, 20
composite video ports 45, 46, 47, 48
high-density ports 14
line level input port (Windows-based
computers) 17
monitor port 12–13, 15
sound input and output ports 5, 17,
18, 19, 44
S-video ports 45, 46, 47, 48
video port 12
positioning the monitor 10
power
conserving 89
disconnecting 2
troubleshooting 67, 68
power button 5, 7, 21, 32
power cord 5, 7, 12
power indicator light 5, 7, 21, 67, 68
power jumper cord 12
power requirements 92
power strip 12
R
resolution
changing (Mac OS) 34, 36
standard 8, 90–91
RGB (red, green, blue) values,
identifying (Mac OS) 37
Rotate option (Geometry menu,
Windows) 60
S
safety precautions
cleaning screen 1
electrical safety 2–3, 11
plugging in ADB connector 13
plugging in S-video connector 47
scan ranges 8
Scan Rate option (Tools menu,
Windows) 61
screen
adjusting images on (Mac OS–based
computers) 32–38
adjusting images on (Windows-based
computers) 58–62
adjusting to match environment 11
blurred or fuzzy images or text on 71
cleaning 1, 65–66
color problems on 71
dark images on 68
dark or dim 68
flickering 69
glare on 10
images fail to appear on 68
off-center images on 70
over- or undersized images on 70
resolution of. See resolution
snow on 71
technical information about 89
tilted images on 70
wavy lines on 71
screen controls 32, 57
screen geometry, adjusting (Windows)
59–60
security lock 66
service provider 66
setting up the monitor 1–23
shielded connector cable 20
sleep mode
Mac OS–based computers 40
Windows-based computers 60, 61
snow on screen 71
software. See AppleVision software
software license agreement 26
sound
adjusting on a Mac OS–based
computer 34, 42–44
adjusting on a Windows-based
computer 63
muting 75
recording 19, 43
troubleshooting 72–75
Sound button (Monitors & Sound control
panel, Mac OS) 34, 44
sound cable 5, 17
sound controls on front of AppleVision
850AV Display 42, 63
sound controls on screen, (Mac OS) 34,
43–44
sound equipment, connecting to your
AppleVision 850AV Display
17–19
sound input and output connectors 17
sound input and output ports 5, 17, 18,
19, 44
speakers, built-in (AppleVision 850AV
Display)
adjusting sound (Mac OS–based
computers) 34, 42–44
adjusting sound (Windows-based
computers) 63
energy saver mode and (Mac OS) 40
illustration of 4, 5
muting (Mac OS–based computers)
42, 74, 75
muting (Windows-based
computers) 63
Index
103
Can’t Find It?
See also Macintosh
Guide’s onscreen index.
Open the Guide (h)
menu and choose
Macintosh Guide
(or Mac OS Guide);
then click the
Index button.
playing audio CDs through (Mac
OS–based computers) 52–53
as sound output source (Mac
OS–based computers) 43
specifications for 91
troubleshooting 72, 73, 74
turning on or off in sleep mode (Mac
OS) 40
turning on or off in sleep mode
(Windows) 60, 61
speakers, external
adjusting volume and balance of (Mac
OS) 34
as sound output source (Mac
OS–based computers) 43
specifications 89–95
standard modes 90
stereo miniplug 18, 48, 50
support 23
S-video connector 47, 48
S-video format 45
System 7.1, AppleVision software and
30–31
System 7.5 or later, AppleVision
software and 28–30
T
technical information 89–95
technical support 23
temperature requirements 93
text, blurred or fuzzy on screen 71
theft, avoiding 66
3D sound
specifications for 91
turning on and off 44
tilted images on screen 70
Tools menu (Windows) 60–61
treble, setting
Mac OS–based computers 42, 44
Windows-based computers 63
treble controls 5, 42, 63
104
Index
troubleshooting 23, 66–79
alert sound fails 78
AppleVision 850AV Display 72–75
blank or unreadable screen 71
blurred or fuzzy images or text 71
brightness 69
color 71, 79
contrast 68
dark images on screen 68
dark screen 68
dim screen 68
error messages 76–77
flickering screen 69
headphones 72, 73, 74
images are too large or too small 70
images fail to appear on screen 68
microphone 74, 75
Monitors & Sound control panel
(Mac OS) 76–79
off-center images on screen 70
overscan 78
power 67, 68
recording sound 74, 75
resolution settings 71, 78
screen appearance 68–71
snow on screen 71
sound (AppleVision 850AV Display)
72–75
speakers 72, 73, 74
tilted images on screen 70
wavy lines on screen 71
white point 79
turning the monitor on 21–22
U
unplugging the monitor 2
updating Apple software 23
user controls, specifications for 90
V
W, X, Y, Z
VCR, connecting to a Mac OS–based
computer 48–51
Vertical option (Convergence menu,
Windows) 62
vertical refresh rate 8, 90–91
Vertical Shift option (Geometry menu,
Windows) 59
VESA standard modes 8
VGA adapter 14, 15, 95
video cable 48, 50
video card
connecting monitor connector to 13
determining need for 8–9
video connectors 14
video equipment, connecting to a Mac
OS–based computer 48–51
video port 12
videos, recording (Mac OS–based
computers) 45–52
viewable image size 1
viewing angle, adjusting 10
voltage requirements 92
volume, adjusting
Mac OS–based computers 34, 42, 44
Windows-based computers 63
volume controls 5, 34, 42, 63
waking up the monitor (Mac OS) 40
warranty 66
wavy lines on screen 71
weight of the monitor 9, 92
white point
setting (Mac OS) 34
setting (Windows) 61
troubleshooting (Mac OS) 79
Width option (Geometry menu,
Windows) 59
Windows-based computers
adjusting screen images on monitor
58–62
adjusting sound on AppleVision
850AV Display 63
connecting monitor cable to 15
installing AppleVision setup
information for Windows 95
operating system 56–57
using onscreen controls 58–62
using the monitor with 9, 22, 55–63
video card for 9
Windows 95, installing AppleVision
setup information for 56–57
World Wide Web sites provided by
Apple Computer 23
Index
105

AppleVision Display
User’s manual for the AppleVision 850 and 850AV
K Apple Computer, Inc.
© 1997 Apple Computer, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without the
written consent of Apple. Your rights to the software are governed by the accompanying
software license agreement.
The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other
countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes without
the prior written consent of Apple may constitute trademark infringement and unfair
competition in violation of federal and state laws.
Every effort has been made to ensure that the information in this manual is accurate. Apple is
not responsible for printing or clerical errors.
Apple Computer, Inc.
1 Infinite Loop
Cupertino, CA 95014-2084
408-996-1010
http://www.apple.com
Apple, the Apple logo, AppleCD, AppleVision, ColorSync, the ColorSync logo, LaserWriter,
Mac, Macintosh, Performa, PlainTalk, and PowerBook are trademarks of Apple Computer, Inc.,
registered in the U.S. and other countries.
Finder and OneScanner are trademarks of Apple Computer, Inc.
Adobe, Acrobat, Adobe Illustrator, Photoshop, and PostScript are trademarks of Adobe Systems
Incorporated or its subsidiaries and may be registered in certain jurisdictions.
Helvetica and Times are registered trademarks of Linotype-Hell AG and/or its subsidiaries.
NuBus is a trademark of Texas Instruments.
Pantone is a registered trademark of Pantone, Inc.
PowerPC is a trademark of International Business Machines Corporation, used under license
therefrom.
Trinitron is a trademark of Sony Corporation, registered in the U.S. and other countries.
Simultaneously published in the United States and Canada.
Mention of third-party products is for informational purposes only and constitutes neither an
endorsement nor a recommendation. Apple assumes no responsibility with regard to the
performance or use of these products.
Contents
Communications regulation information
viii
1 Setting Up Your Monitor 1
Important safety and cleaning instructions
What about electromagnetic emissions?
1
3
Getting ready to set up your AppleVision 850AV Display
Your AppleVision 850AV Display at a glance
5
Getting ready to set up your AppleVision 850 Display
Your AppleVision 850 Display at a glance
Do you need to install a video card?
Mac OS–based computers
Windows-based computers
6
7
8
9
9
Choosing a good location for your monitor
Positioning the monitor
4
9
10
iii
Connecting the monitor to your computer
Connecting the power cord
11
12
Connecting the monitor cable to a Mac OS–based computer
12
Connecting the monitor cable to a Windows-based computer
15
Connecting a Mac OS–based computer keyboard and mouse to
your monitor
16
Connecting sound equipment to your AppleVision 850AV Display
Connecting the sound cable
17
Connecting external sound equipment
Connecting sound input equipment
18
19
Connecting sound output equipment
Using more than one monitor
Turning the monitor on
19
20
21
Using the monitor with Windows-based computers
Finding answers
22
23
Obtaining online support and updated Apple software
What to do next
23
24
Mac OS–based computers
24
Windows-based computers
24
2 Installing and Using AppleVision Software
Installing AppleVision software
25
25
Learning about AppleVision software with System 7.5 or later
Tips for using Monitors & Sound Guide
29
Learning about AppleVision software with System 7.1
Screen controls at a glance
iv
Contents
17
32
30
28
About the Monitors & Sound control panel
Opening Monitors & Sound
33
Monitors & Sound buttons at a glance
Tips for using AppleVision software
Using the Control Strip
33
34
35
36
Using DigitalColor Meter
36
Opening DigitalColor Meter
37
Specifying colors using the Pantone Matching System
Conserving energy
38
38
Setting up Energy Saver
39
What happens after you turn on the energy-saving feature?
Using Energy Saver with a screen saver
40
40
3 Using Sound and Video With Your AppleVision 850AV Display
Sound controls at a glance
About sound sources
42
43
Sound input sources
43
Sound output sources
43
Selecting sound options in Monitors & Sound
Tips for using sound controls
43
44
Setting up your monitor to record a video with sound
About video equipment
45
45
Using video equipment with your monitor
Recording a video
41
48
52
Playing an audio CD through the monitor’s speakers
52
Contents
v
4 Using Your Monitor With Windows-Based Computers
Installing AppleVision setup information for Windows 95
Screen controls at a glance
Using onscreen controls
56
57
58
Adjusting screen geometry
59
Adjusting color settings and other features
Adjusting convergence
60
62
Adjusting sound on your AppleVision 850AV Display
Tips for using sound controls
5 Tips and Troubleshooting
Care and cleaning
55
63
63
65
65
Protecting your monitor from theft
Troubleshooting common problems
66
66
Monitor power and screen appearance
67
Sound on your AppleVision 850AV Display
72
Monitors & Sound control panel for Mac OS–based computers
Appendix A Using ColorSync
81
The problem that ColorSync solves
How ColorSync works
81
82
Setting up ColorSync
84
Setting the ColorSync System Profile
Setting other ColorSync profiles
Tips for best results
86
Appendix B Technical Information
Index
vi
Contents
97
89
86
85
76
Communications regulation information
FCC statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection
against radio interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used
in accordance with Apple’s instructions, may cause interference to radio communications.
Operation of this equipment in a residential area is likely to cause such interference, in which
case the user will be required to correct the interference at his or her own expense.
IMPORTANT Changes or modifications to this product not authorized by Apple Computer, Inc.,
could void the FCC verification and negate your authority to operate the product.
This product was tested for FCC compliance under conditions that included the use of Apple
peripheral devices and Apple shielded cables and connectors between system components. It is
important that you use Apple peripheral devices and shielded cables and connectors between
system components to reduce the possibility of causing interference to radios, television sets,
and other electronic devices. You can obtain Apple peripheral devices and the proper shielded
cables and connectors through an Apple-authorized dealer. For non-Apple peripheral devices,
contact the manufacturer or dealer for assistance.
Industry Canada statement
This Class A device meets all requirements of the Canadian interference-causing equipment
regulations.
Cet appareil numérique de la Class A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
CISPR 22 statement
IMPORTANT This is a Class A product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.
VCCI Class 1 statement
Contents
vii

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement