Yamaha RX-V463 Owner`s manual

RX-V463_G-cv.fm Page 1 Friday, January 11, 2008 10:21 AM
G
Karcher
Kendo
Kenwood
National
NEC
1048
1000, 1001, 1007,
1011, 1043, 1051
Neckermann
1043, 1046
NEI
1046
Nesco
1050
Nikko
1003
Noblex
1002, 1014
Nokia
1043, 1047
Nordmende
1043
Oceanic
1042, 1043
Okano
1044
Olympus
1004
Optimus
1003, 1008
Orion
1012, 1013, 1044,
1065
Orson
1042
Osaki
1042, 1045, 1050
Otto Versand 1046
Palladium
1043, 1045, 1050
Panasonic
1004, 1020, 1034,
1040, 1048, 1054,
1072
Pathe Marconi 1043
Penney
1010, 1014
Pentax
1010, 1049
Perdio
1042
Philco
1004, 1051
Philips
1004, 1025, 1033,
1046, 1056, 1057,
1059, 1062, 1063
Philips Magnavox
1018
Phonola
1046
Pilot
1003
Pioneer
1011, 1046
Prinz
1042
Profex
1050
Profitronic
1014
Proline
1042
Proscan
1009
Prosonic
1044
Protec
1006
Pye
1046, 1056
Quarter
1001
Quartz
1001, 1047
Quasar
1004, 1035
Quelle
1042, 1046, 1047
Radio Shack
1003
Radio Shack/Realistic
1001, 1002, 1003,
1004, 1005, 1008
Radiola
1046
Radix
1003
Randex
1003
RCA
1002, 1004, 1009,
1010, 1014, 1015,
1022, 1032
Realistic
1001, 1002, 1003,
1004, 1005, 1008
Rex
1043
RFT
1046
Roadstar
1045, 1050, 1066
Saba
1043
Saisho
1044, 1050
Salora
1047
Samsung
1002, 1014, 1021,
1027, 1052, 1068,
1070
Sanky
1008
Sansui
1007, 1011, 1013,
1043
Sanyo
1001, 1002, 1014,
1047
SBR
1046
Schaub Lorenz 1042, 1043, 1047
Schneider
1042, 1044, 1045,
1046, 1050
Scott
1012
Sears
1001, 1003, 1004,
1010
SEG
1050
SEI-Sinudyne 1046
Seleco
1043
Sentron
1050
Sharp
1008, 1023, 1028,
1053, 1073
Shintom
1006, 1047, 1050
Shivaki
1045
Shogun
1002, 1014
Siemens
1045, 1047
Signature 2000 1008
Silva
1045
Singer
1004, 1006
Sinudyne
1046
Sontec
1045
Sony
1016, 1019, 1055,
1060, 1064, 1074
STS
1004, 1010
Sunkai
1044
© 2008
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY. LTD. LEVEL 1, 99 QUEENSBRIDGE STREET, SOUTHBANK, VIC 3006, AUSTRALIA
Black process 45.0° 240.0 LPI
Sunstar
Suntronic
Sunwood
Sylvania
1042
1042
1050
1004, 1005, 1031,
1041
Symphonic
1005
Taisho
1044
Tandy
1001
Tashiko
1003, 1042
Tatung
1007, 1042, 1043,
1046, 1066
TCM
1044, 1048
Teac
1005, 1007
Technics
1004, 1048
Teknika
1003, 1004, 1005
Teleavia
1043
Telefunken
1043
Tenosal
1050
Tensai
1042, 1045, 1050
Tevion
1044, 1048
Thomson
1043, 1058
Thorn
1043, 1047
TMK
1002, 1014
Tokai
1045, 1050
Tonsai
1050
Toshiba
1013, 1024, 1029,
1043, 1046, 1066,
1075
Totevision
1002, 1003, 1014
Towada
1050
Towika
1050
Uher
1045
Unitech
1002, 1014
Universum
1042, 1045, 1046
Vector Research 1000
Video Concepts 1000
Videon
1044, 1048
Videosonic
1002, 1014
Wards
1002, 1003, 1004,
1005, 1006, 1008,
1010, 1014
Weltblick
1045
White Westinghouse
1013
XR-1000
1004, 1005, 1006
Yamaha
1000, 1001, 1007
Yamishi
1050
Yokan
1050
Yoko
1045, 1050
Zenith
1013, 1026, 1037
All rights reserved.
Printed in China
WN25730
RX-V463
1046
1044
1000, 1001, 1007,
1011, 1043
KLH
1006
Kodak
1003, 1004
Korpel
1050
Leyco
1050
LG
1003, 1042, 1045,
1071
Lifetec
1044, 1048
Lloyd's
1005
Loewe
1048
Loewe Opta
1045, 1046
Logik
1006, 1050
Luxor
1047
LXI
1003
M Electronic 1042
Magnasonic
1047
Magnavox
1004, 1018, 1033
Magnin
1003, 1014
Manesth
1050
Marantz
1000, 1001, 1004,
1046, 1051
Marta
1003
Matsui
1044, 1045
Matsushita
1004
Mediator
1046
Medion
1044, 1048
MEI
1004
Memorex
1001, 1002, 1003,
1004, 1005, 1008,
1013, 1014, 1042,
1045, 1047
Memphis
1050
Metz
1048
MGA
1014
MGN Technology
1002, 1014
Micromaxx
1044, 1048
Microstar
1044, 1048
Migros
1042
Minolta
1010
Mitsubishi
1011, 1042, 1046
Montgomery Ward
1008
Motorola
1004, 1008
MTC
1002, 1014
Multitech
1002, 1005, 1006,
1042, 1046, 1050
Murphy
1042
RX-V463
AV Receiver
Ampli-tuner audio-vidéo
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
GEBRUIKSAANWIJZING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
Caution: Read this before operating your unit.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in a environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– other components, as they may cause damage and/or
discoloration on the surface of this unit.
– burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
18 Before moving this unit, press ASTANDBY/ON to set this
unit in the standby mode, and disconnect the AC power plug
from the wall outlet.
19 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC wall outlet. Voltages are:
Asia model ............................ 220/230–240 V AC, 50/60 Hz
General model ........ 110/120/220/230–240 V AC, 50/60 Hz
En
20 Excessive sound pressure from earphones and headphones can
cause hearing loss.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
if this unit itself is turned off by ASTANDBY/ON.
This state is called the standby mode. In this state, this
unit is designed to consume a very small quantity of
power.
■ For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
This symbol mark is according to the
EU directive 2002/96/EC.
This symbol mark means that electrical
and electronic equipment, at their endof-life, should be disposed of separately
from your household waste.
Please act according to your local rules
and do not dispose of your old products
with your normal household waste.
Contents
Features ................................................................... 2
Getting started ........................................................ 3
Quick start guide .................................................... 4
Displaying the Radio Data System information ...... 46
Selecting the Radio Data System program type
(PTY SEEK mode) .............................................. 47
Using the enhanced other networks (EON) data
service.................................................................. 48
Using a USB memory device or a USB portable
audio player .......................................................49
Playback operation .................................................. 49
Using iPod™ ..........................................................51
Controlling iPod™................................................... 51
Using Bluetooth™ components............................53
PREPARATION
Pairing the Bluetooth™ adapter and your
Bluetooth™ component....................................... 53
Playback of the Bluetooth™ component ................. 53
Recording ...............................................................54
Connections ............................................................. 9
Using AUTO SETUP .............................................. 24
BASIC OPERATION
SET MENU ............................................................55
Using SET MENU................................................... 56
1 SOUND MENU.................................................... 57
2 INPUT MENU...................................................... 62
3 OPTION MENU................................................... 64
Remote control features........................................67
Controlling this unit, a TV, or other components.... 67
Setting remote control codes ................................... 69
Advanced setup......................................................70
ADDITIONAL INFORMATION
Troubleshooting.....................................................71
Glossary..................................................................81
Specifications .........................................................83
Index .......................................................................84
Selecting the desired SCENE template.................... 28
Creating your original SCENE templates................ 31
Using remote control on the SCENE feature........... 32
Playback ................................................................ 33
Sound field programs ........................................... 38
Sound field program descriptions............................ 38
Using audio features ............................................. 41
Enjoying high quality sound.................................... 41
Adjusting the tonal quality....................................... 41
Adjusting the speaker level...................................... 41
Selecting the night listening mode........................... 42
FM/AM tuning ...................................................... 43
Front panel................................................................i
Remote control ....................................................... ii
List of remote control codes ................................. iii
About this manual
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the
front panel or the ones on the remote control. In case the button
names differ between the front panel and the remote control, the
button name on the remote control is given in parentheses.
• This manual is printed prior to production. Design and specifications
are subject to change in part as a result of improvements, etc. In case
of differences between the manual and product, the product has
priority.
• “JSPEAKERS” or “3DVD” (example) indicates the name of the
parts on the front panel or the remote control. Refer to the attached
sheet or the pages at the end of this manual for the information about
each position of the parts.
• The symbol “☞ ” with page number(s) indicates the corresponding
reference page(s).
1 En
English
Automatic tuning ..................................................... 43
Manual tuning.......................................................... 43
Automatic preset tuning........................................... 44
Manual preset tuning ............................................... 44
Selecting preset stations........................................... 45
Exchanging preset station ........................................ 45
(at the end of this manual)
APPENDIX
Basic operations....................................................... 33
Selecting audio input jacks
(AUDIO SELECT).............................................. 34
Selecting the MULTI CH INPUT component......... 34
Displaying the current status of this unit
on a video monitor............................................... 35
Using your headphones............................................ 35
Muting the audio output........................................... 35
Playing video sources in the background
of an audio source................................................ 36
Displaying the input source information ................. 36
Using the sleep timer ............................................... 37
APPENDIX
ADDITIONAL
INFORMATION
Selecting the SCENE templates........................... 28
ADVANCED
OPERATION
Optimizing the speaker setting
for your listening room .................................... 24
ADVANCED OPERATION
BASIC
OPERATION
Rear panel .................................................................. 9
Placing speakers....................................................... 10
Connecting speakers ................................................ 11
Information on jacks and cable plugs ...................... 13
Information on HDMI™.......................................... 14
Audio and video signal flow.................................... 14
Connecting video components................................. 15
Connecting other components ................................. 16
Connecting audio components................................. 18
Connecting a Yamaha iPod™ universal dock or
Bluetooth™ adapter............................................. 19
Using the VIDEO AUX jacks on the front panel .... 19
Connecting the FM and AM antennas ..................... 20
Connecting the power cable..................................... 20
Turning on and off the power .................................. 21
Front panel display .................................................. 22
PREPARATION
Preparation: Check the items ..................................... 4
Step 1: Set up your speakers...................................... 5
Step 2: Connect your DVD player and other
components............................................................ 6
Step 3: Press SCENE 1 button................................... 7
What do you want to do with this unit?..................... 8
Radio Data System tuning
(Europe and Russia models only) ....................46
INTRODUCTION
INTRODUCTION
Features
Features
Built-in 5-channel power amplifier
HDMI (High-Definition Multimedia Interface)
◆ Minimum RMS output power
◆ HDMI interface for standard, enhanced or high-definition
video (includes 1080p video signal transmission) as well as
multi-channel digital audio
[U.S.A. and Canada models]
(1 kHz, 0.9% THD, 8 Ω)
105 W/ch
[Other models]
(1 kHz, 0.9% THD, 6 Ω)
105 W/ch
SCENE select function
DOCK terminal
◆ DOCK terminal to connect a Yamaha iPod universal dock
(such as YDS-10, sold separately) or Bluetooth adapter
(such as YBA-10, sold separately)
USB features
◆ Preset SCENE templates for various situations
◆ SCENE template customizing capability
◆ USB port to connect a USB memory device or a USB portable
audio player
◆ MP3, WMA and WAV capability
Decoders and DSP circuits
Other features
◆ Proprietary Yamaha technology for the creation of multichannel surround sound
◆ Compressed Music Enhancer mode
◆ Dolby Digital decoder
◆ Dolby Pro Logic/Dolby Pro Logic II decoder
◆ DTS decoder
◆ Virtual CINEMA DSP
◆ SILENT CINEMA™
Radio tuners
◆ FM/AM tuning capability
◆ Radio Data System capability (Europe model only)
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
◆ YPAO (Yamaha Parametric Room Acoustic Optimizer) for
automatic speaker setup
◆ 192-kHz/24-bit D/A converter
◆ DIRECT mode for high quality sound for all sources
◆ 6 additional input jacks for discrete multi-channel input
◆ OSD (on-screen display) menus that allow you to optimize
this unit to suit your individual audiovisual system
◆ Component video input/output capability
(3 COMPONENT VIDEO INs and 1 MONITOR OUT)
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ Cinema and music night listening modes
◆ iPod controlling capability
◆ Remote control with preset remote control codes
“DTS” and “DTS Digital Surround” are registered trademarks of
DTS, Inc.
Bluetooth™
Bluetooth is a registered trademark of the Bluetooth SIG and is
used by Yamaha in accordance with a license agreement.
“SILENT CINEMA” is a trademark of Yamaha Corporation.
iPod™
“iPod” is a trademark of Apple, Inc., registered in the U.S. and
other countries.
2 En
“HDMI”, the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks or registered trademarks of HDMI
Licensing LLC.
Getting started
Getting started
■ Installing batteries in the remote control
Check that you received all of the following parts.
❏
❏
❏
❏
❏
1
Remote control
Batteries (2) (AAA, R03, UM-4)
Optimizer microphone
AM loop antenna
Indoor FM antenna
3
INTRODUCTION
■ Supplied accessories
2
■ VOLTAGE SELECTOR
(Asia and General models only)
Caution
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local voltage BEFORE
plugging the power cable into the AC wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
Rotate the VOLTAGE SELECTOR clockwise or
counterclockwise to the correct position using a
straight slot screwdriver.
Voltages are as follows:
Asia model ................... 220/230–240 V AC, 50/60 Hz
General model
...................... 110/120/220/230–240 V AC, 50/60 Hz
1
Take off the battery compartment cover.
2
Insert the two supplied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
3
Snap the battery compartment cover back
into place.
Notes
VOLTAGE
SELECTOR
230240V
Voltage indication
• Change all of the batteries if you notice that the operation range
of the remote control decreases.
• Do not use an old battery and a new one together.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries and set up the remote control
code.
English
3 En
Quick start guide
Quick start guide
The following steps describe the easiest way to enjoy
DVD movie playback in your home theater.
Preparation: Check the items
Prepare the following items.
Video monitor
Front right
speaker
Front left
speaker
Subwoofer
Surround right
speaker
Center speaker
1. Two surround speakers
2. Center speaker
DVD player
❏ Active subwoofer ...................................x 1
Select an active subwoofer equipped with an RCA
input jack.
Surround left
speaker
Step 1: Set up your speakers
☞ P. 5
Step 2: Connect your DVD player
and other components
☞ P. 6
Step 3: Press SCENE 1 button
☞ P. 7
Enjoy DVD playback!
4 En
❏ Speakers
❏ Front speaker .....................................x 2
❏ Center speaker ...................................x 1
❏ Surround speaker ..............................x 2
Select magnetically shielded speakers. The
minimum required speakers are two front speakers.
The priority of the requirement of other speakers is
as follows:
❏ Speaker cable .........................................x 5
❏ Subwoofer cable .....................................x 1
Select a monaural RCA cable.
❏ DVD player ..............................................x 1
Select DVD player equipped with coaxial digital
audio output jack and composite video output
jack.
❏ Video monitor ..........................................x 1
Select a TV monitor, video monitor or projector
equipped with a composite video input jack.
❏ Video cable .............................................x 2
Select an RCA composite video cable.
❏ Digital coaxial audio cable ....................x 1
Quick start guide
Be sure to connect the left channel (L), right channel
(R), “+” (red) and “–” (black) properly.
Step 1: Set up your speakers
Front and center speakers
INTRODUCTION
Place your speakers in the room and connect them to this
unit.
SPEAKERS
COAXIAL
DTV/CBL IN2
DTV/CBL
CD
2
3
1
OUT
HDMI
DVD
Loosen
OPTICAL
DVD
DVD IN1
DIGITAL INPUT
COMPONENT VIDEO
PR
PB
Y
Insert
Tighten
DOCK
PR
PB
ANTENNA
DTV/CBL
Y
AM
DVR
R SURROUND L
GND
VIDEO
VIDEO
MONITOR OUT
FM
75
UNBAL.
DVD
DTV/CBL
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
L
L
CENTER
R
SUB
WOOFER
R
IN
MD/ OUT
(PLAY) CD-R (REC)
IN
OUT
DVR
FRONT
CD
AUDIO
SURROUND
CENTER
SUB
WOOFER
MULTI CH INPUT
R FRONT A
L
R FRONT B L
OUTPUT
1
Place your speakers and subwoofer in the
room.
2
Connect speaker cables to each speaker.
To the center
speaker
To the front
right speaker
To the front
left speaker
Surround speakers
Cables are colored or shaped differently, perhaps with
a stripe, groove or ridge. Connect the striped
(grooved, etc.) cable to the “+” (red) terminals of
your speaker. Connect the plain cable to the “–”
(black) terminals.
3
Connect each speaker cable to the
corresponding speaker terminal of this unit.
1
2
3
4
To the surround
right speaker
1 Make sure that this unit and the subwoofer are
unplugged from the AC wall outlets.
2 Twist the exposed wires of the speaker cables
together to prevent short circuits.
3 Do not let the bare speaker wires touch each other.
4 Do not let the bare speaker wires touch any metal
part of this unit.
4
To the surround
left speaker
Connect the subwoofer cable to the input
jack of the subwoofer and the SUBWOOFER
OUTPUT jack of this unit.
Subwoofer
AV receiver
Subwoofer cable
5 En
English
SUBWOOFER
OUTPUT jack
Input jack
Quick start guide
Step 2: Connect your DVD player
and other components
3
SPEAKERS
COAXIAL
DTV/CBL
DTV/CBL
CD
CD
2
3
1
OUT
HDMI
DVD
DOCK
DIGITAL INPUT
COMPONENT VIDEO
PR
PB
Y
AV receiver
Video monitor
OPTICAL
OPTICAL
DVD
DTV/CBL IN2
DVD IN1
Connect the video cable to the video input
jack of your video monitor and the VIDEO
MONITOR OUT jack of this unit.
PR
PB
ANTENNA
DTV/CBL
Y
AM
DVR
R SURROUND L
GND
MONITOR OUT
VIDEO
VIDEO
VIDEO
FM
75
UNBAL.
DVD
DTV/CBL
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
L
L
CENTER
R
SUB
WOOFER
R
IN
MD/ OUT
(PLAY) CD-R (REC)
IN
OUT
FRONT
CD
DVR
AUDIO
SURROUND
CENTER
SUB
WOOFER
MULTI CH INPUT
R FRONT A
L
R FRONT B
L
OUTPUT
Make sure that this unit and the DVD
player are unplugged from the AC wall
outlets.
1
Connect the digital coaxial audio cable to the
digital coaxial audio output jack of your DVD
player and the DVD DIGITAL INPUT COAXIAL
jack of this unit.
DVD player
AV receiver
Digital coaxial
audio output jack
Video input
jack
Video cable
4
VIDEO MONITOR OUT
jack
Connect the power plug of this unit and other
components into the AC wall outlet.
■ For further connections
• Using the other kind of speaker
combinations
☞ P. 11
• Connecting video components
☞ P. 15
• Connecting a DVD player
☞ P. 16
• Connecting a DVD recorder
☞ P. 17
• Connecting a set-top box
☞ P. 17
• Connecting a CD player
and a CD recorder/MD recorder
☞ P. 18
• Connecting a multi-format player
or an external decoder
☞ P. 18
• Connecting a Yamaha iPod/Bluetooth dock
☞ P. 19
• Using the VIDEO AUX jacks on the front
panel
☞ P. 19
Digital coaxial audio
cable
DVD DIGITAL INPUT
COAXIAL jack
2
Connect the video cable to the composite
video output jack of your DVD player and the
DVD VIDEO jack of this unit.
DVD player
Composite video
output jack
6 En
Video cable
AV receiver
DVD VIDEO jack
• Connecting an FM/AM antenna
☞ P. 20
• Using the USB jack on the front panel
☞ P. 49
Quick start guide
Step 3: Press SCENE 1 button
Turn on the video monitor and then set the
input source selector of the video monitor to
this unit.
2
Press Q SCENE 1.
This unit is turned on. “DVD Viewing” appears in the
front panel display, and this unit automatically
optimize own status for the DVD playback.
Just by pressing one SCENE button, you can turn on this
unit and recall your favorite input source and sound field
program according to the SCENE template that has been
assigned to the SCENE button. The SCENE templates are
built combinations of input sources and sound field
programs.
y
If you connect a Yamaha product that has capability of the
SCENE control signals, this unit can automatically activate the
component and start playback. Refer to the instruction manual of
the DVD player for further information.
■ The default assigned SCENE templates
Default
SCENE
button
y
The indicator on the selected SCENE button lights up while
this unit is in the SCENE mode.
3
Start playback of the desired DVD on your
player.
4
Rotate IVOLUME to adjust the volume.
INTRODUCTION
1
■ About SCENE function
The name of the SCENE template
and its description
SCENE
1
DVD Movie Viewing
– input source: DVD
– sound field program: Movie Dramatic
For when you want to enjoy a movie from the
connected DVD player.
SCENE
2
Music Disc Listening
– input source: DVD
– sound field program: 2ch Stereo
For when you want to listen to a music disc from
the connected DVD player.
SCENE
3
TV Viewing *1
– input source: DTV/CBL
– sound field program: STRAIGHT
For when you want to watch a TV program.
SCENE
4
Radio Listening *2, *3, *4
– input source: TUNER
– sound field program: 5ch Enhancer
For when you want to listen to a music program
from the FM radio station.
Notes
*1
You must connect a cable TV or a satellite tuner to this unit in
advance. See page 17 for details.
*2 You need to connect the supplied FM and AM antennas to this
unit in advance. See page 20 for details.
*3 You must tune into the desired radio station in advance. See
pages 43 to 45 for tuning information.
*4 To achieve the best possible reception, orient the connected
AM loop antenna, or adjust the position of the end of the
indoor FM antenna.
Note
When you change the input source or sound field program, the
SCENE mode is deactivated.
y
You can change the assigned SCENE template for the SCENE
buttons. See page 28 for details.
English
7 En
Quick start guide
■ After using this unit...
Press A STANDBY/ON on the front panel to set
this unit to the standby mode.
What do you want to do with this
unit?
■ Customizing the SCENE templates
• Using various SCENE templates
☞ P. 28
• Creating your original SCENE templates
☞ P. 31
■ Using various input sources
This unit is set to the standby mode. In the standby mode,
this unit consumes a small amount of power in order to
receive infrared signals from the remote control. To turn
on this unit from the standby mode, press A STANDBY/
ON (or GPOWER). See page 21 for details.
• Basic controls of this unit
☞ P. 33
• Enjoying FM/AM radio programs
☞ P. 43
• Using your USB portable device
with this unit
☞ P. 49
• Using your iPod with this unit
☞ P. 51
• Using your Bluetooth components
with this unit
☞ P. 53
■ Using various sound features
• Using various sound field programs
☞ P. 38
• Using the direct mode for the high
quality sound
☞ P. 41
• Customizing the sound field programs
☞ P. 40
■ Adjusting the parameters of this unit
• Automatically optimizing the speaker
parameters for your listening room
(AUTO SETUP)
☞ P. 24
• Manually adjusting various parameters of
this unit
☞ P. 55
• Setting the remote control
☞ P. 67
• Adjusting the advanced parameters ☞ P. 70
■ Additional features
Automatically turning off this unit
8 En
☞ P. 37
Connections
Connections
Rear panel
1
2
3
4
5
6
SPEAKERS
OPTICAL
DVD
DVD IN1
DTV/CBL IN2
DTV/CBL
DVD
CD
2
1
OUT
HDMI
PREPARATION
COAXIAL
3
DIGITAL INPUT
COMPONENT VIDEO
PR
PB
Y
DOCK
PR
PB
ANTENNA
DTV/CBL
Y
AM
DVR
R SURROUND L
GND
MONITOR OUT
VIDEO
FM
75
UNBAL.
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
L
L
R
R
CENTER
IN
MD/ OUT
(PLAY) CD-R (REC)
OUT
IN
DVD
DTV/CBL
DVR
SUB
WOOFER
FRONT
CD
AUDIO
SURROUND
MULTI CH INPUT
7
8
Name
9
CENTER
SUB
WOOFER
R FRONT A
L
R FRONT B
L
OUTPUT
0 A
Page
1
HDMI jacks
14
2
DIGITAL INPUT jacks
13
3
COMPONENT VIDEO jacks
13
4
DOCK terminal
19
5
Speaker terminals
11
6
VOLTAGE SELECTOR
(Asia and General models only)
3
7
AUDIO jacks
13
8
VIDEO jacks
13
9
MULTI CH INPUT jacks
18
0
SUBWOOFER OUTPUT jack
11
A
ANTENNA terminals
20
English
9 En
Connections
Placing speakers
The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multichannel audio sources.
FL
C
FR
FR
SW
FL
30˚
C
SL
SR
SR
60˚
SL
80˚
SR
SL
Front left and right speakers (FL and FR)
The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the
ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a
center speaker, you can do without it. Best results, however, are obtained with the full system.
Surround left and right speakers (SL and SR)
The surround speakers are used for effect and surround sounds.
Subwoofer (SW)
The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is
effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction
of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is
not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front
speakers. Turn it slightly toward the center of the room to reduce wall reflections.
10 En
Connections
Connecting speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
this unit cannot reproduce the input sources accurately.
Surround speakers
Left
Right
PREPARATION
Caution
• Before connecting the speakers, make sure that the AC power plug is disconnected from the AC wall outlet.
• Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage
this unit and/or the speakers. If the speaker wires are short-circuited, “CHECK SP WIRES” appears in the front
panel display when you turn on this unit.
• Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the
speakers away from the monitor.
SPEAKERS
COAXIAL
OPTICAL
DVD
DVD IN1
DTV/CBL IN2
DTV/CBL
DVD
CD
2
1
OUT
HDMI
3
DIGITAL INPUT
COMPONENT VIDEO
PR
PB
Y
DOCK
PR
PB
ANTENNA
DTV/CBL
Y
AM
DVR
R SURROUND L
GND
VIDEO
VIDEO
MONITOR OUT
FM
75
UNBAL.
DVD
DTV/CBL
IN
DVR OUT
MONITOR
OUT
L
L
R
R
CENTER
IN
MD/ OUT
(PLAY) CD-R (REC)
IN
DVD
DTV/CBL
AUDIO
OUT
DVR
CD
SUB
WOOFER
FRONT
SURROUND
CENTER
SUB
WOOFER
MULTI CH INPUT
R FRONT A
L
R FRONT B
L
OUTPUT
FRONT B terminals
Connect the alternative front speaker system
(FRONT B).
Center
speaker
Subwoofer
Left
Right
Front speakers
(FRONT A)
English
11 En
Connections
■ Before connecting to the SPEAKERS
terminal
A speaker cord is actually a pair of insulated cables
running side by side. Cables are colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals of this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
Remove approximately 10 mm (3/8”) of insulation
from the end of each speaker cable and then
twist the bare wires of the cable together to
prevent short circuits.
10 mm (3/8”)
■ Connecting to the SPEAKER terminals
2
1
Red: positive (+)
Black: negative (–)
3
1
Loosen the knob.
2
Insert the bare end of the speaker wire into
the hole on the terminal.
3
Tighten the knob to secure the wire.
Connecting the banana plug
(except Europe, Russia, Korea, and Asia models)
The banana plug is a single-pole electrical connector
widely used to terminate speaker cables. First, tighten the
knob and then insert the banana plug connector into the
end of the corresponding terminal.
Banana plug
12 En
Connections
Information on jacks and cable plugs
Connect one of the type of the audio jack(s) and/or video jack(s) that your input components are equipped with.
Audio jacks and cable plugs
DIGITAL AUDIO
R
COAXIAL
OPTICAL
(White)
(Red)
(Orange)
L
R
C
AUDIO
Left and right
analog audio
cable plugs
Coaxial
digital audio
cable plug
COMPONENT VIDEO
PR
PB
Y
VIDEO
(Yellow)
(Red)
(Blue)
(Green)
O
V
PR
PB
Y
Optical
digital
audio cable
plug
Composite
video cable
plug
PREPARATION
DIGITAL AUDIO
L
Video jacks and cable plugs
Component
video cable
plugs
■ Audio jacks
■ Video jacks
This unit has three types of audio jacks. Connection
depends on the availability of audio jacks on your other
components.
This unit has two types of video jacks. Connection
depends on the availability of input jacks on your video
monitor.
AUDIO jacks
For conventional analog audio signals transmitted via left
and right analog audio cables. Connect red plugs to the
right jacks and white plugs to the left jacks.
VIDEO jacks
For conventional composite video signals transmitted via
composite video cables.
DIGITAL AUDIO COAXIAL jack
For digital audio signals transmitted via a coaxial digital
audio cable.
COMPONENT VIDEO jacks
For component signals, separated into the luminance (Y)
and chrominance (PB, PR) video signals transmitted on
separate wires of component video cables.
DIGITAL AUDIO OPTICAL jacks
For digital audio signals transmitted via optical digital
audio cables.
Video signal flow for MONITOR OUT
Notes
COMPONENT
VIDEO
• You can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. Optical input jacks are compatible with digital
signals with up to 96 kHz of sampling frequency.
• This unit handles digital and analog signals independently. Thus
audio signals input at the digital jacks are not output at the
analog AUDIO OUT (REC) jacks.
Input
PR PB Y
Output
(MONITOR OUT)
PR PB Y
VIDEO
Note
The OSD signal is not output at the DVR OUT (REC) jacks.
English
13 En
Connections
Information on HDMI™
■ HDMI compatibility with this unit
Audio signal
types
Audio signal
formats
Compatible
HDMI
components
2ch Linear PCM
2ch, 32-192 kHz,
16/20/24 bit
CD, DVD-Video,
DVD-Audio, etc.
Multi-ch Linear
PCM
8ch, 32-192 kHz,
16/20/24 bit
DVD-Audio, etc.
Bitstream
Dolby Digital, DTS
DVD-Video, etc.
This unit’s HDMI interface is based on the following
standards:
• HDMI Version 1.2a (High-Definition Multimedia
Interface Specification Version 1.2a) licensed by
HDMI Licensing, LLC.
• HDCP (High-bandwidth Digital Content Protection
System) licensed by Digital Content Protection,
LLC.
Notes
• When CPPM copy-protected DVD audio is played back, video
and audio signals may not be output depending on the type of
the DVD player.
• This unit is not compatible with HDCP-incompatible HDMI or
DVI components.
• You can check the potential problem about the HDMI
connection (see page 36).
■ HDMI jack and cable plug
HDMI
HDMI cable plug
y
• We recommend using an HDMI cable shorter than 5 meters (16
feet) with the HDMI logo printed on it.
• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect
this unit to other DVI components.
Notes
• Do not disconnect or connect the cable or turn off the power of
the HDMI components connected to the HDMI OUT jack of
this unit while data is being transferred. Doing so may disrupt
playback or cause noise.
• Audio signals input at input jacks other than the HDMI IN DVD
or HDMI IN DTV/CBL jack of this unit cannot be digitally
output at the HDMI OUT jack.
• If you turn off the power of the video monitor connected to the
HDMI OUT jack via a DVI connection, this unit may fail to
establish the connection to the component.
Audio and video signal flow
■ Audio signal flow
Input
■ Video signal flow
Output
Input
HDMI
HDMI
AUDIO
COMPONENT
VIDEO
Digital output
Analog output
Notes
• 2-channel as well as multi-channel PCM, Dolby Digital and
DTS signals input at the HDMI IN DVD or HDMI IN DTV/
CBL jack can be output at the HDMI OUT jack only when
“SUPPORT AUDIO” is set to “Other” (see page 61).
• Audio signals input at the HDMI IN jacks are not output at the
AUDIO output jacks.
14 En
VIDEO
Through
Output
Connections
Connecting video components
Connect your TV (or projector) to the HDMI OUT jack,
the COMPONENT VIDEO MONITOR OUT jacks, or the
VIDEO MONITOR OUT jack of this unit.
Notes
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
y
You can choose to play back HDMI audio signals on this unit or
on another HDMI component connected to the HDMI OUT jack
of this unit. Use the “SUPPORT AUDIO” parameter in “SOUND
MENU” to select the component to play back HDMI audio
signals (see page 61).
COAXIAL
OPTICAL
DVD
VD IN1
DTV/CBL IN2
DTV/CBL
DVD
CD
2
1
OUT
HDMI
PREPARATION
• Some video monitors connected to this unit via a DVI
connection fail to recognize the HDMI audio/video signals
being input if they are in the standby mode. In this case, the
HDMI indicator flashes irregularly.
• When you connect your TV monitor or projector via HDMI
connection, the OSD does not appear. In such cases, connect the
TV monitor or projector via component, or video connection.
• Connect the input source components to the HDMI IN DVD or
HDMI IN DTV/CBL jack to display the video images on the
video monitor connected to the HDMI OUT jack.
3
DIGITAL INPUT
COMPONENT VIDEO
PB
PR
Y
PR
PB
DTV/CBL
Y
DVR
VIDEO
DVD
DTV/CBL
IN
DVR OUT
MONITOR OUT
MONITOR
OUT
L
CENTER
R
D/ OUT
-R (REC)
IN
DVD
DTV/CBL
OUT
AUDIO
SURROUND
SUB
WOOFER
MULTI CH INPUT
PR
HDMI in
WO
FRONT
CD
DVR
PB
OUTPUT
Y
Component
video in
V
Video in
TV (or projector)
indicates recommended connections
indicates alternative connections
English
15 En
Connections
Connecting other components
Notes
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
• Be sure to make the same type of video connections as those
made for your TV (see page 15).
• To make a digital connection to a component other than the
default component assigned to DIGITAL INPUT jack, select
the corresponding setting for “OPTICAL IN” or “COAXIAL
IN” in “INPUT ASSIGNMENT” (see page 62).
■ Connecting a DVD player
DVD player
HDMI out
Component
video out
Coaxial out
Audio out
Video out
R
V
L
PR
C
COAXIAL
DTV/CBL IN2
DTV/CBL
DVD
CD
2
1
OUT
HDMI
Y
OPTICAL
DVD
DVD IN1
PB
3
DIGITAL INPUT
COMPONENT VIDEO
PR
PB
Y
PR
PB
DTV/CBL
Y
DVR
VIDEO
VIDEO
DVD
DTV/CBL
IN
DVR OUT
MONITOR OUT
MONITOR
OUT
L
L
R
R
CENTER
IN
MD/ OUT
(PLAY) CD-R (REC)
IN
DVD
DTV/CBL
AUDIO
OUT
DVR
CD
WO
FRONT
SURROUND
SUB
WOOFER
MULTI CH INPUT
OUTPUT
indicates recommended connections
indicates alternative connections
(One for the video connection,
and one for the audio connection)
16 En
Connections
■ Connecting a DVD recorder, PVR or VCR
DVD
DVD IN1
DTV/CBL IN2
DTV/CBL
CD
2
1
OUT
HDMI
3
DIGITAL INPUT
COMPONENT VIDEO
DVD
PB
PR
Y
PR
DTV/CBL
Y
PB
DVR
MONITOR OUT
VIDEO
VIDEO
DVD
IN
DTV/CBL
MONITOR
OUT
DVR OUT
L
L
R
R
CENTER
DVD
DTV/CBL
OUT
WO
FRONT
CD
DVR
AUDIO
SURROUND
SUB
WOOFER
MULTI CH INPUT
OUTPUT
V
L
R
R
PR
PB
Y
Video in
Audio in
Audio out
V
PREPARATION
IN
IN
MD/ OUT
(PLAY) CD-R (REC)
L
Component video out
Video out
DVD recorder,
PVR or VCR
■ Connecting a set-top box
Satellite receiver, cable TV
receiver or HDTV decoder
HDMI out
Component video out
Optical out
Audio out
Video out
L
V
R
O
PR
COAXIAL
DTV/CBL
DVD
CD
2
1
OUT
HDMI
Y
OPTICAL
DVD
DTV/CBL IN2
DVD IN1
PB
3
DIGITAL INPUT
COMPONENT VIDEO
PR
PB
Y
PB
PR
DTV/CBL
Y
DVR
VIDEO
VIDEO
DVD
DTV/CBL
IN
DVR OUT
MONITOR OUT
MONITOR
OUT
L
indicates recommended
connections
L
CENTER
R
R
IN
DVD
DTV/CBL
AUDIO
OUT
DVR
CD
WO
FRONT
SURROUND
SUB
WOOFER
MULTI CH INPUT
OUTPUT
indicates alternative
connections (One for the video
connection, and one for the
audio connection)
17 En
English
IN
MD/ OUT
(PLAY) CD-R (REC)
Connections
Connecting audio components
Connect the audio components as follows.
■ Connecting a CD player and a CD
recorder/MD recorder
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
Notes
• When you connect your CD player via analog and digital
connection, priority is given to the signal input at the DIGITAL
INPUT jack.
• To make a digital connection to a component other than the
default component assigned to each DIGITAL INPUT jack,
select the corresponding setting in “INPUT ASSIGNMENT”
(see page 62).
indicates recommended connections
indicates alternative connections
COAXIAL
OPTICAL
DVD
DVD IN1
DTV/CBL IN2
DVD
PB
Y
PR
O
MONITOR OUT
VIDEO
VIDEO
R
3
2
DIGITAL INPUT
COMPONENT VIDEO
PR
L
CD
DTV/CBL
1
OUT
HDMI
Optical out
Audio in
DVD
L
DTV/CBL
IN
DVR OUT
MONITOR
OUT
L
L
R
R
L
R
R
Audio out
CD recorder or
MD recorder
IN
MD/ OUT
(PLAY) CD-R (REC)
IN
DVD
DTV/CBL
Audio out
OUT
CD
DVR
AUDIO
FRONT
SURROUND
W
CD player
MULTI CH INPU
■ Connecting a multi-format player or an external decoder
This unit is equipped with 6 additional input jacks (FRONT L/R, SURROUND L/R, CENTER and SUBWOOFER) for
discrete multi-channel input from a multi-format player, external decoder or sound processor. Connect the output jacks
on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right
output jacks to the left and right input jacks for the front and surround channels.
Notes
• When you select the component connected to the MULTI CH INPUT jacks as the input source (see page 34), this unit automatically
turns off the digital sound field processor, and you cannot select sound field programs.
• This unit does not redirect signals input at the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that
you connect a 5.1-channel speaker system before using this feature.
CENTER
L
R
SUB
FRONT
SURROUND
WOOFER
MULTI CH INPUT
L
R
Multi-format player/
External decoder
18 En
Center out
Front out
Subwoofer out
R
Surround out
L
Connections
Connecting a Yamaha iPod™
universal dock or Bluetooth™
adapter
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
Using the VIDEO AUX jacks on the
front panel
Use the VIDEO AUX jacks on the front panel to connect a
game console or a video camera to this unit.
Caution
Be sure to turn down the volume of this unit and other
components before making connections.
• To reproduce the source signals input at these jacks, select
“V-AUX” as the input source.
• When audio signals are input at the AUDIO jacks and the
DOCK terminal on the rear panel, the priority order of the input
signal is as follows:
1. DOCK
2. AUDIO
PREPARATION
Notes
This unit is equipped with the DOCK terminal on the rear
panel that allows you to connect a Yamaha iPod universal
dock (such as YDS-10, sold separately) or Bluetooth
adapter (such as YBA-10, sold separately). Connect a
Yamaha iPod universal dock or Bluetooth adapter to the
DOCK terminal on the rear panel of this unit using its
dedicated cable.
VOLUME
STANDBY/
ON
OPTIMIZER MIC
EDIT
PRESET/TUNING
BAND
l
A/B/C/D/E
PRESET/TUNING/CH
h
MEMORY
TUNING AUTO/MAN'L
SCENE
1
l
DOCK
PB
DTV/CBL
Y
PHONES
SPEAKERS
A/B/OFF
PROGRAM
2
3
STRAIGHT
DIRECT
4
h
l
TONE CONTROL
INPUT
VIDEO AUX
h
AUDIO SELECT
VIDEO
L
AUDIO
USB
R
ANTENNA
DVR
EFFECT
SILENT CINEMA
AM
GND
VIDEO AUX
Yamaha iPod universal dock
or Bluetooth adapter
Video
output
VIDEO
L
V
L
AUDIO
R
R
Audio
output
Game console or
video camera
English
19 En
Connections
Connecting the wire of the AM loop antenna
Connecting the FM and AM
antennas
Open the lever
Insert
Close the lever
Both FM and AM indoor antennas are supplied with this
unit. Connect each antenna correctly to the designated
terminals. In general, these antennas should provide
sufficient signal strength.
y
See right for connection information of the supplied AM loop
antenna.
Notes
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
Yamaha dealer or service center about outdoor antennas.
y
The wire of the AM loop antenna does not have any polarity
and you can connect either end of the wire to AM or GND
terminal.
Assembling the supplied AM loop antenna
Outdoor AM antenna
Use a 5 to 10 m (16 to 33
ft) vinyl-covered wire
extended outdoors from a
window.
AM loop
antenna
(supplied)
Indoor FM
antenna
(supplied)
Note
The types of the supplied AM loop antenna is different
depending on the models.
DOCK
ANTENNA
L
Connecting the power cable
AM
GND
Once all connections are complete, plug the power cable
into the AC wall outlet.
FM
75
UNBAL.
SUB
WOOFER
CENTER
PUT
(U.S.A. model)
Ground (GND terminal)
For maximum safety and minimum interference, connect the
antenna GND terminal to a good earth ground. A good earth
ground is a metal stake driven into moist earth.
Power cable
20 En
Connections
Turning on and off the power
■ Turning on this unit
Press A STANDBY/ON (or G POWER) to turn
on this unit.
y
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
PREPARATION
■ Set this unit to the standby mode
Press A STANDBY/ON (or H STANDBY) to set
this unit to the standby mode.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
English
21 En
Connections
Front panel display
2
1
DVR
MULTI CH
3
V-AUX
DOCK
USB
q DIGITAL
q PL
SP
AB
4
DTV/CBL
DVD
5
MD/CD-R
ENHANCER
6
CD
7
TUNER
VOL.
YPAO MEMORY
VIRTUAL AUTO TUNED STEREO MUTE
SLEEP PTY HOLD PS PTY RT CT EON
SILENT CINEMA
ft
ms
dB
PCM
8
9
0 A
B
C
D
E
dB
LFE
L C R
SL
SR
F
1 HDMI indicator
Lights up when the signal of the selected input source is
input at the HDMI IN jacks (see page 14).
6 Tuner indicators
Lights up when this unit is in the FM or AM tuning mode
(see pages 43 to 45).
2 DOCK indicator
• Lights up when you station your iPod in a Yamaha
iPod universal dock (such as YDS-10, sold separately)
connected to the DOCK terminal of this unit (see
page 19) and V-AUX is selected as the input source.
• Flashes while the connected Yamaha Bluetooth adapter
(such as YBA-10, sold separately) and the Bluetooth
component is in the paring (see page 53) or the
Bluetooth adapter is searching the Bluetooth
component (see page 53).
• Lights up while the connected Yamaha Bluetooth
adapter is connected to the Bluetooth component (see
page 19).
7 MUTE indicator and VOLUME level indicator
• The MUTE indicator flashes while the MUTE function
is on (see page 35).
• Indicates the current volume level.
3 ENHANCER indicator
Lights up when the Compressed Music Enhancer mode is
selected (see page 38).
4 Input source indicators
The corresponding cursor lights up to show the currently
selected input source.
5 YPAO indicator
Lights up when you run “AUTO SETUP” and when the
speaker settings set in “AUTO SETUP” are used without
any modifications (see page 24).
22 En
8 PCM indicator
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
9 Decoder indicators
The respective indicator lights up when any of the
decoders of this unit function.
0 Headphone indicator
Lights up when headphones are connected (see page 35).
A SP A B indicators
Light up according to the set of front speakers activated
(see page 33).
SP A: The FRONT A speakers are activated.
SP B: The FRONT B speakers are activated.
Connections
B CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound
field program (see page 39).
■ Using the remote control
The remote control transmits a directional infrared ray.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 39).
SILENT CINEMA indicator
Lights up when headphones are connected and a
sound field program is selected (see page 39).
30º
30º
PREPARATION
Approximately 6 m (20 ft)
C Multi-information display
Shows the name of the current sound field program and
other information when adjusting or changing settings.
D SLEEP indicator
Lights up while the sleep timer is on (see page 37).
E Radio Data System indicators
(Europe and Russia models only)
PTY HOLD
Lights up while searching for the Radio Data System
stations in the PTY SEEK mode.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
y
PS, PTY, RT and CT
Light up according to the selected Radio Data System
display mode.
To set the remote control codes for other components, see
page 69.
EON
Lights up when the EON data service is being
received.
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or stove
– places of extremely low temperatures
– dusty places
F Input channel and speaker indicators
LFE
L C R
SL
SR
LFE indicator
Notes
Input channel indicators
Input channel indicators
• Indicate the channel components of the current
digital input signal.
• Light up or flash according to the settings of the
speakers when this unit is in the automatic setup
procedure (see page 24) or the speaker level setting
procedure in the “SP LEVEL” (see page 59).
English
23 En
Optimizing the speaker setting for your listening room
Optimizing the speaker setting for your listening room
This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment.
Using AUTO SETUP
2
Notes
• Be advised that it is normal for loud test tones to be output
during the “AUTO SETUP” procedure.
• To achieve the best results, make sure the room is as quiet as
possible while the “AUTO SETUP” procedure is in progress. If
there is too much ambient noise, the results may not be
satisfactory.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
OPTIMIZER MIC
TUNING AUTO/MAN'L
VIDEO AUX
VIDEO
L
AUDIO
USB
R
AUDIO SELECT
y
You can run “AUTO SETUP” using the system menu that
appears in the OSD or in the front panel display. This manual uses
the OSD illustrations to explain the “AUTO SETUP” procedure.
1
Optimizer
microphone
Make sure of the following check points.
The following display appears in the OSD.
Note
AUTO SETUP
Before starting the automatic setup, check the following
check points.
❏
SETUP;;;;;;;AUTO
. START
Automatic
Processing
of all item
[ ]/[ ]:Up/Down
[ENTER]:Start
3
p
❏
Speakers are connected appropriately.
Headphones are disconnected from this unit.
This unit and the video monitor are turned on.
This unit is selected as the video input source of
the video monitor.
The connected subwoofer is turned on and the
volume level is set to about half way (or slightly
less).
The crossover frequency controls of the
connected subwoofer is set to the maximum.
p
❏
❏
❏
❏
Place the optimizer microphone at your
normal listening position on a flat level
surface with the microphone heading
upward.
Optimizer microphone
VOLUME
MIN
MAX
CROSSOVER
HIGH CUT
MIN
MAX
Controls of a subwoofer (example)
❏
❏
FRONT A speakers are selected as the front
speaker system (see page 33).
The room is sufficiently quiet.
y
It is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears would be
when you are seated in your listening position. You can use the
attached screw of a tripod (etc.) to fix the optimizer microphone
to the tripod (etc.).
24 En
Optimizing the speaker setting for your listening room
4
Make sure that “SETUP” is set to “AUTO”
and the pointer is pointing at “START”.
y
You can also select the following setup methods. In this
case, press 7 k to select “SETUP”, press 7 l / h to
select the one of the following choices and then select
“START”.
Note
“RELOAD” or “UNDO” is available only when you have
previously run “AUTO SETUP” and confirmed the results.
5
Press 7 n to select “START” and then press
7 ENTER to start the setup procedure.
The following message appears in the OSD.
NOTICE
Loudtesttonesare
output.
Pleasekeepquiet
orleavetheroom.
Press 7 ENTER to start the setup
procedure.
This unit starts the auto setup procedure. Loud test
tones are output from each speaker during the auto
setup procedure. Once all items are set, the result
display appears in the OSD.
Notes
• During the auto setup procedure, do not perform any
operation on this unit.
• We recommend getting out of the room while this unit is in
the auto setup procedure. It takes approximately 3 minutes
for this unit to complete the auto setup procedure.
This unit performs the following checks:
PREPARATION
Choices: AUTO, RELOAD, UNDO, DEFAULT
• Select “AUTO” to automatically run the entire
“AUTO SETUP” procedure.
• Select “RELOAD” to reload the last “AUTO
SETUP” settings and override the previous
settings.
• Select “UNDO” to undo the last “AUTO SETUP”
settings and restore the previous settings.
• Select “DEFAULT” to reset the “AUTO SETUP”
parameters to the initial factory settings.
6
Speaker wiring/volume level WIRING/LEVEL
Checks which speakers are connected and the
polarity of each speaker. Also checks and adjusts the
volume level of each speaker.
Speaker distance
DISTANCE
Checks the distance of each speaker from the
listening position and adjusts the timing of each
channel.
Speaker size
SIZE
Checks the frequency response of each speaker and
sets the appropriate low-frequency crossover for each
channel.
Press[ENTER]
Before proceeding next operation
Once you perform the next operation, this unit starts the
automatic setup procedure. For more accurate
measurements, keep quiet and move to the wall where
speakers are not around. We recommend that you leave
the listening room during the automatic setup
procedure.
English
25 En
Optimizing the speaker setting for your listening room
The display changes as follows.
7
Press 7 k and 7 ENTER to display the
setup results in detail.
8
Press 7 l / h repeatedly to toggle between
the setup result displays.
AUTO SETUP
SETUP;;;;;;;AUTO
. START
p
p
Automatic
Processing
of all item
[ ]/[ ]:Up/Down
[ENTER]:Start
Results of the speaker
connection and wiring
AUTO SETUP
Results of the speaker
distance from the
listening position
INITIALIZING
. WIRING/LEVEL
DISTANCE
SIZE
[
WAITING;;;
;;;;;;;;;;
[]:Exit
Results of the speaker
size
AUTO SETUP
RESULT
SP :
3/2/0.1
DIST: 3.2/3.5m
LVL :
-2/+2dB
. >SET
CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
Results of the speaker
output level
y
If you are not satisfied with the results or want to manually
adjust each parameter, run “MANUAL SETUP” (see
page 55).
The results displayed under “RESULT” are as follows.
Number of speakers SP
Displays the number of speakers connected to this unit in
the following order:
Front/Back/Subwoofer
Speaker distance DIST
Displays the speaker distance from the listening position
in the following order:
Closest speaker distance/Farthest speaker distance
Speaker level LVL
Displays the speaker output level in the following order:
Lowest speaker output level/Highest speaker output level
Notes
• If “E-9:INTERNAL ERROR” appears during the testing
procedure, restart from step 4.
• If you selected “RELOAD” in step 4, no test tones are output.
• If an error occurs during the “AUTO SETUP” procedure, the
setup procedure is canceled and an error screen appears. For
details, see “If an error screen appears” on page 27.
• When this unit detects potential problems during the “AUTO
SETUP” procedure, “WARNING” and the number of warning
messages appears (see page 27).
26 En
Note
The distances displayed in the “DISTANCE” results may be
longer than the actual distance depending on the
characteristics of your speakers.
9
Press 7 ENTER to return to the result
display.
AUTO SETUP
. RESULT
SP :
3/2/0.1
DIST: 3.2/3.5m
LVL :
-2/+2dB
CANCEL
>SET
[ ]/[ ]:Up/Down
[ENTER]:Detail
Optimizing the speaker setting for your listening room
10
11
Press 7 n and then press 7 l / h to select
“SET” or “CANCEL”.
Choices: SET, CANCEL
• Select “SET” to confirm the “AUTO SETUP”
results.
• Select “CANCEL” to cancel the “AUTO SETUP”
results.
Press 7 ENTER to confirm your selection.
The top “SET MENU” display appears in the OSD.
■ If “WARNING” appears
When this unit detects potential problems during the
“AUTO SETUP” procedure, “WARNING” appears in the
result display. Check the warning messages to correct your
speaker settings.
Note
Warnings differ from errors in that warnings do not cancel the
“AUTO SETUP” procedure.
1
TOP MENU
. ;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
PREPARATION
SET MENU
Make sure the pointer is pointing at
“WARNING” and then press 7 ENTER to
display the detailed information about the
warning.
The number on the right of “WARNING” indicates
the number of warning messages.
12
Press K MENU to exit from “SET MENU”.
13
Disconnect the optimizer microphone from
this unit.
The optimizer microphone is sensitive to heat. Keep
it away from direct sunlight and do not place it on top
of this unit.
AUTO SETUP
. WARNING(2)
RESULT
SP :
3/2/0.1
DIST: 3.2/3.5m
LVL :
-2/+2dB
CANCEL
>SET
[ ]/[ ]:Up/Down
[ENTER]:Detail
2
Press 7 l / h repeatedly to toggle between
the warning displays.
y
WARNING
If you change speakers, speaker positions, or the layout of your
listening environment, run “AUTO SETUP” again to recalibrate
your system.
W-1:OUT OF PHASE
Reverse channel
AAAAFLAAAAA--AAACENTER
AAAASLAAAAA---
■ If an error screen appears
[ ]/[ ]:Select
[ENTER]:Return
Press 7 k / n / l / h to select “RETRY” or
“EXIT” and then press 7 ENTER.
The following display is an example where “E-8:USER
CANCEL” appears in the OSD.
y
• For details about each warning message, see the “AUTO
SETUP” section in “Troubleshooting” on page 75.
• When the corresponding warning message is not
applicable to a speaker, “– – –” is displayed instead.
ERROR
. E-8:USER CANCEL
Can't detect
signal at MIC
>RETRY
3
Press 7 ENTER to return to the result
display.
EXIT
[ ]/[ ]:Select
[ENTER]:Enter
Choices: RETRY, EXIT
• Select “RETRY” to retry the “AUTO SETUP”
procedure.
• Select “EXIT” to exit from the “AUTO SETUP”
procedure.
English
27 En
SELECTING THE SCENE TEMPLATES
Selecting the SCENE templates
This unit is equipped with 16 preset SCENE templates for
various situations of using this unit. As the initial factory
setting, the following SCENE templates are assigned to
each SCENE button:
2
Press O INPUT l / h (or press 4 AMP and
then press 7l / h) to select the desired
template.
SCENE 1: DVD Movie Viewing
SCENE 2: Music Disc Listening
SCENE 3: TV Viewing
SCENE 4: Radio Listening
l
INPUT
h
Front panel
If you want to use other SCENE templates, you can select
the desired SCENE templates from the SCENE template
library and assign the templates to the selected SCENE
buttons on the front panel and the remote control.
or
AMP
ENTER
Select the desired SCENE
template
Remote control
1
Assign the
SCENE
template to the
SCENE button
SCENE template library
(Image)
Selecting the desired SCENE
template
1
Press and hold the desired QSCENE (or
5 SCENE) button for 3 seconds.
The indicator on the selected SCENE button on the
front panel starts to flash, and the name of the
currently assigned SCENE template appears in the
front panel display.
3 seconds
3 seconds
or
1
Front panel
1
Remote control
1
Flashes
DVD MovieView
28 En
DVD Viewing
3
Press the QSCENE (or 5 SCENE) button
again to confirm the selection.
The selected SCENE template is assigned to the
button.
1
Front panel
or
1
Remote control
Note
Once the desired SCENE templates are assigned to the
corresponding SCENE buttons, you may need to set the input
source of the SCENE template on the remote control. See page 32
for details.
Selecting the SCENE templates
■ Which SCENE template would you like to select?
Which source do you like to
play back?
Video sources
(DVD video,
Recorded video)
Which component do you
like for playback?
DVD
SCENE templates
Default
SCENE buttons
DVD Viewing
DVD Movie Viewing
1
DVD Live Viewing
Music discs (CD, SACD
or DVD-Audio)
DVR
DVR Viewing
DVD
Disc Hi-fi Listening
Music Disc Listening
2
Disc Listening
CD
CD Hi-fi Listening
BASIC
OPERATION
CD Listening
CD Music Listening
Radio programs
TUNER (FM/AM)
Radio Listening
iPod or Bluetooth
component
DOCK
Dock Listening
USB memory device
or USB portable
audio player
USB
USB Audio Listening
TV programs
DTV/CBL
TV Viewing
4
3
TV Sports Viewing
Video games
V-AUX*
Game Playing
Note
* When iPod is connected to the Yamaha iPod universal dock or a Bluetooth component is connected to the Bluetooth adapter, this unit
plays back the audio sources input at the DOCK terminal.
y
You can create your original SCENE templates by editing the preset SCENE templates. See page 31 for details.
English
29 En
Selecting the SCENE templates
■ Preset SCENE templates descriptions
The illustrations of the SCENE button in the following table indicate the assigned SCENE buttons in the default setting.
SCENE template
Input source
Playback mode
Features
DVD Viewing
DVD
STRAIGHT
DVD Movie Viewing
DVD
MOVIE
Movie Dramatic
Select this SCENE template when you play back movies on
your DVD player.
DVD Live Viewing
DVD
MUSIC
Pop/Rock
Select this SCENE template when you enjoy the music live
video on your DVD player.
DVR Viewing
DVR
MOVIE
Movie Dramatic
Select this SCENE template when you play back movies on
your digital video recorder.
Disc Hi-fi Listening
DVD
DIRECT
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your DVD player.
Music Disc
Listening
DVD
STEREO
2ch Stereo
Select this SCENE template when you play back music discs
on your DVD player.
Disc Listening
DVD
STEREO
5ch Stereo
Select this SCENE template when you play back music
sources on your DVD player as the background music.
CD Hi-fi Listening
CD
DIRECT
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your CD player.
CD Listening
CD
STEREO
5ch Stereo
Select this SCENE template when you play back music discs
on your CD player as the background music.
CD Music Listening
CD
STEREO
2ch Stereo
Select this SCENE template when you play back music source
on your CD player.
Radio Listening
TUNER
MUSIC ENHANCER Select this SCENE template when you enjoy FM or AM radio
programs.
5ch Enhancer
DOCK
MUSIC ENHANCER Select this SCENE template when you play back music on
your iPod stationed in a Yamaha iPod universal dock or
5ch Enhancer
Select this SCENE template when you play back general
contents on the DVD player.
1
2
4
Dock Listening
Bluetooth component that is connected to the Bluetooth
adapter.
USB Audio
Listening
USB
TV Viewing
DTV/CBL
STRAIGHT
TV Sports Viewing
DTV/CBL
ENTERTAINMENT
TV Sports
Select this SCENE template when you enjoy sports programs
on your TV.
Game Playing
V-AUX
ENTERTAINMENT
Game
Select this SCENE template when you play video games.
MUSIC ENHANCER Select this SCENE template when you play back music on
your USB memory device or a USB portable audio player.
5ch Enhancer
Select this SCENE template when you enjoy general
programs on your TV.
3
30 En
Selecting the SCENE templates
Creating your original SCENE
templates
3
You can create your original SCENE templates for each
SCENE button. You can refer to the preset 16 SCENE
templates to create the original SCENE templates.
■ Customizing the preset SCENE
templates
• INPUT:
• MODE:
Create the original SCENE
template
SCENE : DVD Viewing
SCENE : DVD Viewing
INPUT : DVD
SCENE template library
(Image)
4
Press the 5 SCENE button again to confirm
the edit.
1
BASIC
OPERATION
The input source component
The active sound field programs,
STRAIGHT or DIRECT mode (see
pages 39 and 41)
• NIGHT:
The night listening mode setting (see
page 42)
− SYSTEM: Keeps the current night listening
mode.
− CINEMA: Sets the night listening mode to the
CINEMA mode.
− MUSIC: Sets the night listening mode to the
MUSIC mode.
Use this feature to customize the preset SCENE templates.
Select a SCENE template
Press 4 AMP and then 7 k / n to select the
desired parameter of the SCENE template
and then 7 l / h to select the desired value
of the selected parameter.
You can adjust the following parameters for a
SCENE template:
1
Assign to the SCENE
button
y
1
2
Turn on the video monitor connected to this
unit.
Press and hold the desired 5 SCENE button
for 3 seconds.
The SCENE template customizing screen appears on
the video monitor.
1
3 seconds
An asterisk mark (*) appears by the name of the original SCENE
template.
Notes
• Once the desired SCENE templates are assigned to the
corresponding 5 SCENE buttons, you may need to set the
input source of the SCENE template on the remote control. See
page 32 for details.
• You can create a customized SCENE template for each
5 SCENE button, and if you create another customized
SCENE template, this unit overwrites the old customized
SCENE template with the new one.
• The newly created template is only available for the assigned
5 SCENE button.
■ Renaming the SCENE templates
Note
When the SCENE template you want to customize is not
assigned to any of the 5 SCENE buttons, press 4 AMP
and then press 7l / h repeatedly to recall the desired
SCENE template on the menu screen.
31 En
English
Select the name of the SCENE template at step 3
of “Customizing the preset SCENE templates”
and then press 7 ENTER.
• Press 7k / n to select the desired character.
• Press 7l / h to place “_” (underscore) under the
space or the desired character.
• Press 8 RETURN to cancel the new name.
• Press 7 ENTER to confirm the new name.
Selecting the SCENE templates
Using remote control on the SCENE feature
■ Controlling the input source
components in the SCENE mode
■ Setting input source of the customized
SCENE template on the remote control
You can operate both this unit and the input source
component by using the remote control. You must set the
appropriate remote control code for each input source in
advance (see page 69).
If you customize the input source of the selected SCENE
template, you must set the input source of the SCENE
template on the remote control to operate the input source
component correctly.
1
Press the desired 5 SCENE button on the
remote control.
2
Press the desired buttons in the * area below
to control the input source component of the
selected SCENE template.
y
*
POWER
POWER
STANDBY
POWER
TV
AV
USB
A
B
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
C
B
D
C
AMP
TV INPUT
TV MUTE
1
2
TV CH
TV VOL
SCENE
3
4
SCENE buttons
SRCH MODE
VOLUME
MENU
BAND LEVEL
TITLE
ENTER
DISPLAY
RETURN
MEMORY
REC
FREQ/TEXT
EON
MODE - PTY SEEK - START
l
PROG h
1
2
3
4
STRAIGHT
DIRECT
NIGHT
PARAMETER
5
6
ENHANCER SUR. DECODE
7
MULTI CH IN AUDIO SEL
9
0
10
8
SLEEP
ENT
Note
*
Press and hold the 5 SCENE button and the
desired input selector button (3) for 3 seconds.
These buttons control the input source component. See page 68
for details of the function of each button.
32 En
Press the 5 SCENE button again to operate the input source
component.
PLAYBACK
Playback
Caution
Extreme caution should be exercised when you play
back CDs encoded in DTS. If you play back a CD
encoded in DTS on a DTS-incompatible CD player,
you will only hear some unwanted noise that may
damage your speakers. Check whether your CD player
supports CDs encoded in DTS. Also, check the sound
output level of your CD player before you play back a
CD encoded in DTS.
Basic operations
1
3
Rotate I VOLUME (or press
L VOLUME +/–) to adjust the volume to the
desired output level.
6
Press L PROGRAM l / h repeatedly (or
press 4 AMP and then A PROG l / h
repeatedly) to select the desired sound field
program.
The name of the selected sound field program appears
in the front panel display.
See page 38 for details about sound field programs.
Turn on the video monitor connected to this
unit.
Press J SPEAKERS repeatedly to select the
front speakers you want to use.
The respective speaker indicators lights up in the
front panel display.
Press O INPUT l / h repeatedly (or press
one of the input selector buttons (3)) to
select the desired input source.
The name of the currently selected input source
appears in the front panel display for a few seconds.
Available input sources
MULTI CH
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
CD
TUNER
USB
INPUT:DVD
Currently selected input
source
Movie Dramatic
Currently selected
surround field program
Notes
• Choose a sound field program based on your listening
preference, not merely on the name of the program.
• When you select an input source, this unit automatically selects
the last sound field program used with the corresponding input
source.
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 34).
• When PCM signals with a sampling frequency higher than 48
kHz are input, this unit is automatically set to the “STRAIGHT”
mode (see page 39).
• To display information about the currently selected input source
in the OSD, see page 36 for details.
■ A quick guide to contents
When you want to...
4
Start playback on the selected component or
select a broadcast station.
• Refer to the operating instructions for the source
component.
• See page 43 for details about FM/AM tuning
instructions.
BASIC
OPERATION
2
5
See
page
Enjoy high quality sound
41
Adjust the tonal quality of the front speakers
41
Adjust the parameters of sound field programs
40
Enjoy the sources with a wide dynamic range at night
42
Use headphones
35
Select a decoder to play back sources with
39
Automatically set this unit to the standby mode
37
English
33 En
Playback
Selecting audio input jacks
(AUDIO SELECT)
This unit comes with a variety of input jacks. Use this
feature (audio input jack select) to switch between input
jacks when more than one input jack is assigned to as the
same input source.
y
• We recommend setting the audio input jack select to “AUTO”
in most cases.
• You can adjust the default audio input jack select of this unit by
using “AUDIO SELECT” in “OPTION MENU” (see page 65).
Selecting the MULTI CH INPUT
component
Use this feature to select the component connected to the
MULTI CH INPUT jacks (see page 18) as the input
source.
Press O INPUT l / h repeatedly (or press
4 AMP and then D MULTI CH IN) to select
MULTI CH.
“MULTI CH” appears in the front panel display.
y
Press PAUDIO SELECT (or press 4 AMP and
then E AUDIO SEL) repeatedly to select the
desired audio input jack select setting.
Available input sources
MULTI CH
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
CD
TUNER
USB
A.SEL:AUTO
Currently selected audio input jack select setting
AUDIO SELECT
Function
AUTO
Automatically selects input signals in the
following order:
(1) HDMI
(2) Digital signals
(3) Analog signals
HDMI
Selects only HDMI signals. When HDMI
signals are not input, no sound is output.
COAX/OPT
Selects only digital signals. When no
signals are input, no sound is output.
ANALOG
Selects only analog signals. If no analog
signals are input, no sound is output.
Note
This feature is not available when no digital input jacks
(OPTICAL, COAXIAL and HDMI) are assigned. In addition,
HDMI is not available as an audio input jack select setting when
the HDMI IN DVD and HDMI IN DTV/CBL jacks are not used.
Use “INPUT ASSIGNMENT” in “INPUT MENU” to reassign
the respective input jack (see page 62).
34 En
Use “MULTI CH SET” menu in “INPUT MENU” to set the
parameters for MULTI CH INPUT (see page 63).
Note
The input signals are amplified and output directly without sound
processing. Therefore, you cannot activate sound field programs,
the night listening mode, etc. while MULTI CH is selected as the
input source.
Playback
Displaying the current status of
this unit on a video monitor
You can display the operating information of this unit on a
video monitor.
1
Turn on the video monitor connected to this
unit.
2
Press M DISPLAY.
The current status screen appears in the OSD.
Using your headphones
Connect a pair of headphones with a stereo
analog audio cable plug to the PHONES jack on
the front panel.
y
You can select the amount of time that the current status is
displayed in the OSD by using the “OSD-AMP” parameter in
“OPTION MENU” (see page 64).
y
Note
Notes
The OSD signal is not output at the DVR VIDEO OUT jacks and
will not be recorded.
• When you connect headphones, no signals are output at the
speaker terminals.
• All Dolby Digital and DTS audio signals are mixed down to the
left and right headphone channels.
When you select a sound field program, SILENT CINEMA mode
is automatically activated (see page 39).
BASIC
OPERATION
STATUSVOL:-40dB
DVDMovieViewing
MOVIE
MovieSpacious
INPUT:DVD
A.SEL:HDMI
NIGHT:CINEMA(MID)
[DISPLAY]:STATUSOFF
Muting the audio output
Press I MUTE to mute the audio output. Press
I MUTE again to resume the audio output.
y
• You can also rotate I VOLUME or press LVOLUME +/– to
resume the audio output.
• You can adjust the muting level by using the “MUTE TYPE”
parameter in “SOUND MENU” (see page 60).
• The MUTE indicator flashes in the front panel display when the
audio output is muted and disappears from the front panel
display when the audio output is resumed.
English
35 En
Playback
Playing video sources in the
background of an audio source
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
Press the input selector buttons (3) to select a
video source and then an audio source.
■ Audio information
Information
Descriptions
FORMAT
Signal format. When this unit cannot detect a
digital signal, it automatically switches to
analog input.
SAMPLING
The number of samples per second taken from
a continuous signal to make a discrete signal.
CHANNEL
The number of source channels in the input
signal (front/surround/LFE). For example, a
multi-channel soundtrack with 3 front
channels, 2 surround channels and LFE, is
displayed as “3/2/0.1”.
BITRATE
The number of bits passing a given point per
second.
FLAG
Flag data encoded in DTS, Dolby Digital, or
PCM signals that cue this unit to automatically
switch decoders.
USB
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
Audio sources
Video sources
V-AUX
Note
y
• You can also select “MULTI CH” as the audio source (see
page 34). Press 4 AMP and then press D MULTI CH IN.
• Set the “BGV” parameter in the “MULTI CH SET” menu to the
desired setting to select the default background video input
source of the MULTI CH INPUT sources (see page 63).
Displaying the input source
information
“–––” appears when this unit cannot display the corresponding
information.
■ Video information
Information
HDMI SIGNAL
Type of the source video signals and the
video signals output at the HDMI OUT
jack of this unit.
HDMI RES.
Resolution of the HDMI signals input or
output at the HDMI IN/OUT jacks of this
unit.
HDMI ERROR
Error message for HDMI sources or
connected HDMI devices. See “HDMI
error and message” for details.
You can display the format, sampling frequency, channel,
bit rate and flag data of the current input signal.
1
Press 4 AMP and then K MENU.
The top “SET MENU” display appears in the OSD.
SET MENU
. ;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
“–––” appears when this unit cannot display the corresponding
information.
HDMI error and message
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
Press 7 n repeatedly to select “SIGNAL
INFO” and then press 7 ENTER.
The audio information about the input source appears
in the OSD.
3
Press 7 l / h to toggle between the audio
and video information displays.
4
Press K MENU again to exit from “SET
MENU”.
36 En
(Only when error
is detected)
Note
TOP MENU
2
Descriptions
Message
Cause
DEVICE OVER
The number of the connected HDMI
components is over the limit.
HDCP ERROR
HDCP authentication failed.
OUT OF RES.
The connected monitor is not compatible
with the resolution of the input video signal.
Playback
Using the sleep timer
Use this feature to automatically set this unit to the
standby mode after a certain amount of time.
Press 4 AMP and then press R SLEEP
repeatedly to set the amount of time.
Each time you press R SLEEP, the front panel display
changes as shown below.
SLEEP 120min
SLEEP OFF
SLEEP 30min
SLEEP 90min
SLEEP 60min
The SLEEP indicator flashes while you are switching the
amount of time for the sleep timer. Once the sleep timer is
set, the SLEEP indicator lights up in the front panel
display, and the display returns to the selected sound field
program.
BASIC
OPERATION
y
• To cancel the sleep timer, press 4 AMP and then press
R SLEEP repeatedly until “SLEEP OFF” appears in the front
panel display.
• The sleep timer setting can also be canceled by pressing
A STANDBY/ON (or H STANDBY) to set this unit to the
standby mode.
English
37 En
SOUND FIELD PROGRAMS
Sound field programs
This unit is equipped with a variety of precise digital
decoders that allow you to enjoy multi-channel playback
from almost any stereo or multi-channel sound source.
Press L PROGRAM l / h (or press 4 AMP and
then press A PROG l / h repeatedly).
The name of the selected sound field program appears in
the front panel display.
Notes
• When you select an input source, this unit automatically selects
the last sound field program used with the corresponding input
source.
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 34).
• When PCM signals with a sampling frequency higher than 48
kHz are input, this unit is automatically set to the “STRAIGHT”
mode (see page 39).
y
Choose a sound field program based on your listening preference,
not merely on the name of the program itself.
Sound field program descriptions
Category
MUSIC
Program
Features
Pop/Rock
CINEMA DSP processing. This program presents an image of pop, rock, or jazz live
concert. The sound field reproduces the spaciousness of a massive pavilion with an emphasis
on the vividness of vocals on the stage and solo instruments and the beats of rhythm
instruments.
Hall
CINEMA DSP processing. This sound field is suitable for classic and orchestral music. The
program uses data collected in a large concert hall in Munich. You can enjoy delicate and
beautiful reverberation and a majestic atmosphere.
Jazz
CINEMA DSP processing. The sound field is suitable for jazz and fusion music. It uses data
collected in a famous jazz club in New York. You can enjoy clear reverberation.
Game
CINEMA DSP processing. You can enjoy dynamic and thrilling sound effects as you play
games. The program lets you feel the depth and three-dimensional surrounding sounds of the
field where you are playing, and offers cinema-like surrounding sound effects for the scenes
of movies.
TV Sports
CINEMA DSP processing. You can enjoy sports relays broadcast in stereo and variety shows
with a live sound environment. For sports relays, the voices of commentators and
announcers come clearly from the center; the cheers and atmosphere in the stadium spread
around within a comfortable range, and you can feel like as if you are in the stadium.
Movie Spacious
CINEMA DSP processing. The sound field is suitable for movies with an emphasis on
spectacular sound effects, and is a perfect fit with a wide screen. The program reproduces a
wide dynamic range from minimum sound effects to powerful sounds.
Movie Dramatic
CINEMA DSP processing. This sound field is also suitable for movies with an emphasis on
three-dimensional sound effects. It restrains reverberation to an moderate extent, but
reproduces sound effects and background music in a soft, three-dimensional manner with
clarity and center orientation of voices as pivots.
2ch Stereo
Downmixes multi-channel sources to 2 channel or plays back 2-channel sources as they are.
5ch Stereo
CINEMA DSP processing. Using this program increases the listening position range. This is
a sound field suitable for background music at parties.
2ch Enhancer
5ch Enhancer
Select these programs to play back compression artifacts (such as the MP3 format) in
2-channel or 5-channel stereo. This program enhances your listening experience by
regenerating the missing harmonics in a compression artifact.
ENTERTAINMENT
MOVIE
STEREO
MUSIC
ENHANCER
Note
The sound field programs of this unit are recreations of real-world acoustic environments made from precise measurements taken in the
actual concert hall, music venue, movie theater, etc. Thus, you may notice variations in the strength of the reflections coming from each
direction.
38 En
Sound field programs
■ Enjoying 2-channel sources using the
standard decoders
Signals input from 2-channel sources can also be played
back on multi-channels.
Press 4 AMP and then press OSUR. DECODE
repeatedly to select a decoder.
You can select from the following decoders depending on
the type of source you are playing and your personal
preference.
Decoder
Functions
Dolby Pro Logic processing for any
sources
PLII Movie
Dolby Pro Logic II processing for
movie sources
PLII Music
Dolby Pro Logic II processing for
music sources
PLII Game
Dolby Pro Logic II processing for
game sources
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers by creating
virtual speakers.
If you set “SUR. L/R SP” to “NONE” (see page 58),
Virtual CINEMA DSP is automatically activated
whenever you select a CINEMA DSP program
(see page 38).
Note
Virtual CINEMA DSP will not be activated even when
“SUR. L/R SP” is set to “NONE” (see page 58) in the following
cases:
– when “5ch Stereo” (see page 38) is selected.
– when headphones are connected to the PHONES jack.
■ Enjoying multi-channel sources and
sound field programs with headphones
(SILENT CINEMA)
SILENT CINEMA allows you to enjoy multi-channel
music or movie sound, including Dolby Digital and DTS
sources, through ordinary headphones. SILENT CINEMA
is automatically activated whenever you connect
headphones to the PHONES jack while listening to
CINEMA DSP sound field programs (except for 5ch
Stereo) (see page 38). When activated, the SILENT
CINEMA indicator lights up in the front panel display.
BASIC
OPERATION
Pro Logic
■ Using sound field programs without
surround speakers
(Virtual CINEMA DSP)
■ Enjoying unprocessed input sources
(Straight decoding mode)
When this unit is in the “STRAIGHT” mode, multichannel sources are decoded straight into the appropriate
channels without any additional effect processing. 2channel stereo sources are output from only the front left
and right speakers.
Press M STRAIGHT (or press 4 AMP and then
press B STRAIGHT) to select “STRAIGHT”.
To deactivate the “STRAIGHT” mode, press
M STRAIGHT (or press 4 AMP and then
B STRAIGHT) again so that “STRAIGHT” disappears
from the front panel display.
English
39 En
Sound field programs
■ Editing sound fields parameters
y
You can enjoy good quality sound with the factory default
parameters. Although you do not have to change the initial
settings, you can change some of the parameters to better
suit the input source or your listening room.
For Pop/Rock, Hall, Jazz, Game, TV Sports,
Movie Spacious and Movie Dramatic:
1
While listening to a source, press 4 AMP
and then press QPARAMETER.
2
Press 7k / n to select the desired parameter
you want to change.
3
Press 7l / h to change the parameter
value.
Initial settings are indicated in bold under each parameter.
DSP level DSP LEVEL
Function:
Adjusts the effect level.
Choices:
MIN, MID, MAX
For 2ch Enhancer and 5ch Enhancer:
Note
You cannot change parameter values when “MEMORY
GUARD” in “OPTION MENU” is set to “ON” (see page 64).
Effect level EFFECT LEVEL
Function:
Adjusts the effect level.
Choices:
LOW, HIGH
For Pro Logic II Music:
Panorama PANORAMA
Function:
Sends stereo signals to the surround
speakers as well as the front speakers for
a wraparound effect.
Choices:
OFF, ON
Dimension DIMENSION
Function:
Gradually adjusts the sound field either
towards the front or towards the rear.
Control range: –3 (towards the rear) to +3 (towards the
front), initial setting is STD (standard).
Center width CT WIDTH
Function:
Adjusts the center image from all three
front speakers to varying degrees. A
larger value adjusts the center image
towards the front left and right speakers.
Control range: 0 (center channel sound is output only
from center speaker) to 7 (center channel
sound is output only from front left and
right speakers), initial setting is 3.
40 En
USING AUDIO FEATURES
Using audio features
Enjoying high quality sound
Use the DIRECT mode to enjoy the high quality sounds of
the selected source. When the DIRECT mode is activated,
this unit plays back the selected source with the least
circuitry.
Adjusting the speaker level
You can adjust the output level of each speaker while
listening to a music source. This is also possible when
playing sources input at the MULTI CH INPUT jacks.
Note
Press NDIRECT (or press 4 AMP and then
C DIRECT) to select “DIRECT”.
This operation will override the level adjustments made in
“AUTO SETUP” (see page 24) and “SP LEVEL” (see page 59).
Notes
1
• “TONE CONTROL” and “SOUND MENU” (see page 57)
settings (except for speaker level settings) are not effective.
• The front panel display automatically dims.
Press 4 AMP and then press 6 LEVEL on
the remote control and then 7 k / n to select
the speaker you want to adjust.
Display
While DIRECT mode is activated, the front panel display turns on
momentarily when an operation is performed.
Adjusting the tonal quality
Use this feature to adjust the balance of bass and treble for
the front left and right speaker channels.
y
Speaker and headphone adjustments are stored independently.
1
Press K TONE CONTROL repeatedly to
select the high-frequency response
(TREBLE) or the low-frequency response
(BASS).
2
Press L PROGRAM l / h repeatedly to
adjust the high-frequency response
(TREBLE) or the low-frequency response
(BASS).
Notes
• If you increase or decrease the high-frequency or the lowfrequency sound to an extreme level, the tonal quality of the
surround speakers may not match.
• TONE CONTROL is not effective when this unit is in the
DIRECT mode, or when MULTI CH is selected as the input
source.
Adjusted speaker
FRONT L
Front left speaker
FRONT R
Front right speaker
CENTER
Center speaker
SWFR
Subwoofer
SUR. L
Surround left speaker
SUR. R
Surround right speaker
BASIC
OPERATION
y
y
• The available speaker channels differ depending on the
setting of the speakers.
• When the video monitor is turned on, the “SPEAKER
LEVEL” adjustment menu appears in the video monitor.
2
Press 7 l / h to adjust the speaker output
level.
• Press 7 h to increase the value.
• Press 7 l to decrease the value.
• Control range: –10 dB to +10 dB
3
Press 6 LEVEL to turn off the speaker level
adjustment display.
English
41 En
Using audio features
Selecting the night listening mode
The night listening modes are designed to improve
listenability at lower volumes or at night.
1
Press 4 AMP and then P NIGHT repeatedly
to select “NIGHT:CINEMA” or
“NIGHT:MUSIC”.
Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF
• Select “NIGHT:CINEMA” when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select “NIGHT:MUSIC” when listening to music
sources to preserve ease-of-listening for all sounds.
• Select “OFF” if you do not want to use this feature.
y
When a night listening mode is selected, the NIGHT
indicator lights up in the front panel display.
2
Press 7 l / h to adjust the effect level while
“NIGHT:CINEMA” or “NIGHT:MUSIC” is
displayed in the front panel display.
Effect.Lvl:MID
Choices: MIN, MID, MAX
• Select “MIN” for minimum compression.
• Select “MID” for standard compression.
• Select “MAX” for maximum compression.
y
“NIGHT:CINEMA” and “NIGHT:MUSIC” adjustments are
stored independently.
Notes
• You cannot use the night listening modes in the following cases:
– when the DIRECT mode (see page 41) is selected.
– when the component connected to the MULTI CH INPUT
jacks is selected as the input source (see page 34).
– when headphones are connected to the PHONES jack.
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
42 En
FM/AM TUNING
FM/AM tuning
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 40 stations.
Automatic tuning
Manual tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
If the signal received from the station you want to select is
weak, tune into it manually.
1
Note
Press OINPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
Press C BAND to select the reception band
(FM or AM).
3
Press HTUNING AUTO/MAN’L so that the
AUTO indicator lights up in the front panel
display.
Lights up
1
Press OINPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
2
Press C BAND to select the reception band
(FM or AM).
3
Press HTUNING AUTO/MAN’L so that the
AUTO indicator disappears from the front
panel display.
AUTO
BASIC
OPERATION
2
Manually tuning into an FM station automatically switches the
tuner to monaural reception to increase the signal quality.
AFM 88.90MHz
No colon (:)
AFM 88.90MHz
If a colon (:) appears in the front panel display,
automatic tuning is not possible. Press B PRESET/
TUNING to turn the colon (:) off.
4
Press EPRESET/TUNING/CH l / h once
to begin automatic tuning.
When this unit is tuned into a station, the TUNED
indicator lights up and the frequency of the received
station is shown in the front panel display.
Lights up
No colon (:)
If a colon (:) appears in the front panel display,
manual tuning is not possible. Press B PRESET/
TUNING to turn the colon (:) off.
4
Press EPRESET/TUNING/CH l / h to
tune into the desired station manually.
y
Hold down the button to continue searching.
TUNED
AFM 88.90MHz
English
43 En
FM/AM tuning
Automatic preset tuning
You can use the automatic preset tuning feature to store
FM stations with strong signals up to 40 (A1 to E8: 8
preset station numbers in each of the 5 preset station
groups) of those stations in order. You can then recall any
preset station easily by selecting the preset station number.
1
2
3
Press OINPUT l / h repeatedly so that
“TUNER” is displayed in the front panel
display.
Press C BAND to select “FM” as the
reception band.
Manual preset tuning
You can also store up to 40 stations (A1 to E8: 8 preset
station numbers in each of the 5 preset station groups)
manually.
1
Tune into a station automatically or manually.
See page 43 for tuning instructions.
2
Press F MEMORY.
The MEMORY indicator flashes in the front panel
display for approximately 30 seconds.
3
Press D A/B/C/D/E and EPRESET/
TUNING/CH l / h repeatedly to select a
preset station group (A1 to E8) while the
MEMORY indicator is flashing.
Check that the colon (:) appears in the front panel
display.
Press and hold FMEMORY for more than 3
seconds.
The preset station number as well as the MEMORY
and AUTO indicators flashes. After approximately 5
seconds, automatic presetting starts from the current
frequency and proceeds toward the higher
frequencies.
Flashes
Flashes
MEMORY
A3:FM 88.90MHz
MEMORY
AUTO
Preset station
group and
number
A1:FM 88.90MHz
Colon (:)
Flashes
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
y
4
Press FMEMORY while the MEMORY
indicator is flashing.
The station band and frequency appear in the front
panel display with the preset station group and
number you have selected.
You can select the preset station group and the preset station
number where the first received station will be stored by pressing
D A/B/C/D/E and then EPRESET/TUNING/CH l / h.
TUNED
A1:FM 88.90MHz
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune into it manually
and store it as described in “Manual preset tuning” on this page.
• Only Radio Data System broadcasting station are stored
automatically by automatic preset tuning (Europe and Russia
models only).
44 En
The displayed station has been stored as A1.
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
FM/AM tuning
Selecting preset stations
You can tune into any desired station simply by selecting
the preset station group and number under which it was
stored.
y
When performing this operation with the remote control, press
3 TUNER to select “TUNER” as the input source.
1
2
Press DA/B/C/D/E (or 7A/B/C/D/E l / h)
repeatedly to select the desired preset
station group (A to E).
The preset station group letter appears in the front
panel display and changes each time you press the
button.
Exchanging preset station
You can exchange the assignments of two preset stations
with each other. The example below describes the
procedure to exchange preset station “E1” with “A5”.
1
Select preset station “E1” using DA/B/C/D/E
and EPRESET/TUNING/CH l / h.
See “Selecting preset stations” on this page.
2
Press and hold B PRESET/TUNING for
more than 3 seconds.
“E1” and the MEMORY indicator flash in the front
panel display.
Flashes
BASIC
OPERATION
Press EPRESET/TUNING/CH l / h (or
7 PRESET/CH k / n) to select the desired
preset station number (1 to 8).
The preset station group and number appear in the
front panel display along with the station band and
frequency.
MEMORY
E1:FM 88.90MHz
Flashes
3
E1:FM 88.90MHz
y
You can select the desired preset station number (1 to 8) directly
by pressing the numeric buttons on the remote control.
Select preset station “A5” using DA/B/C/D/E
and EPRESET/TUNING/CH l / h.
“A5” and the MEMORY indicator flash in the front
panel display.
Flashes
MEMORY
A5:FM 88.90MHz
Flashes
4
Press B PRESET/TUNING again.
“EXCHANGE E1–A5” appears in the front panel
display and the assignments of the two preset stations
are exchanged.
English
45 En
RADIO DATA SYSTEM TUNING (EUROPE AND RUSSIA MODELS ONLY)
Radio Data System tuning
(Europe and Russia models only)
Radio Data System is a data transmission system used by FM stations in many countries. This unit can receive various
Radio Data System data such as PS (program service), PTY (program type), RT (radio text), CT (clock time), and EON
(enhanced other networks) when receiving Radio Data System broadcasting stations.
Displaying the Radio Data System
information
1
Tune into the desired Radio Data System
broadcasting station.
• We recommend using the automatic preset tuning
to tune into the Radio Data System broadcasting
stations (see page 44).
• You can also use PTY SEEK mode to tune into the
desired Radio Data System broadcasting station
from the preset ones.
2
Press 0 FREQ/TEXT on the remote control
repeatedly to select the desired Radio Data
System display mode.
Use this feature to display the 4 types of the Radio Data
System information: PS (program service), PTY (program
type), RT (radio text) and CT (clock time). The
corresponding indicators light up in the front panel
display.
Notes
• You can select one of the Radio Data System display modes
only when the corresponding Radio Data System indicator
lights up in the front panel display. It may take a while for this
unit to receive all of the Radio Data System data from the
station.
• You can select only the available Radio Data System display
modes being offered by the station.
• If the signals being received are not strong enough, this unit
may not be able to utilize the Radio Data System data. In
particular, the “RT” mode requires a large amount of data and
may not be available even when the other Radio Data System
display modes are available.
• In case of poor reception conditions, press HTUNING AUTO/
MAN’L on the front panel so that the AUTO indicator
disappears from the front panel display.
• If the signal strength is weakened by external interference while
this unit is receiving the Radio Data System data, the reception
may be cut off unexpectedly and “...WAIT” appears in the front
panel display.
• When the “RT” mode is selected, this unit can display the
program information by a maximum of 64 alphanumeric
characters, including the umlaut symbol. Unavailable characters
are displayed with the “_” (underscore).
• If the reception is cut off when the “CT” mode is selected, “CT
WAIT” appears in the front panel display.
46 En
PS
PTY
RT
CT
Frequency display
• Select “PS” to display the name of the Radio Data
System program currently being received.
• Select “PTY” to display the type of the Radio Data
System program currently being received.
• Select “RT” to display the information on the
Radio Data System program currently being
received.
• Select “CT” to display the current time.
Radio Data System tuning (Europe and Russia models only)
Selecting the Radio Data System
program type (PTY SEEK mode)
Use this feature to select the desired radio program by
program type from the all preset Radio Data System
broadcasting stations.
3
Press 7 PRESET/CH k / n on the remote
control to select the desired program type.
The name of the selected program type appears in the
front panel display.
y
Use the automatic preset tuning feature to preset Radio Data
System broadcasting stations (see page 44).
POP M
Press 3 TUNER on the remote control to
select “TUNER” as the input source.
Lights up
1
Program type
2
NEWS
News
AFFAIRS
Current affairs
INFO
General information
SPORT
Sports
EDUCATE
Education
DRAMA
Drama
CULTURE
Culture
y
SCIENCE
Science
To cancel the PTY SEEK mode, press 0PTY SEEK
MODE on the remote control again.
VARIED
Light entertainment
POP M
Popular music
ROCK M
Rock music
M.O.R. M
Middle-of-the-road music
(easy-listening)
LIGHT M
Light classics
CLASSICS
Serious classics
OTHER M
Other music
NEWS
Flashes
BASIC
OPERATION
Press 0PTY SEEK MODE on the remote
control to set this unit to the PTY SEEK
mode.
The name of the program type or “NEWS” flashes in
the front panel display.
Descriptions
English
47 En
Radio Data System tuning (Europe and Russia models only)
4
Press 0PTY SEEK START on the remote
control to start searching for all the available
Radio Data System preset stations.
The name of the selected program type flashes and
the PTY HOLD indicator lights up in the front panel
display while this unit is searching for stations.
POP M
Flashes
PTY HOLD
Lights up
y
To stop searching for stations, press 0PTY SEEK START
on the remote control again.
Notes
• This unit stops searching for stations when a station
broadcasting the selected program type is found.
• If the station found is not the one you desire, press
0PTY SEEK START again to resume searching for
another station broadcasting the same program type.
Using the enhanced other
networks (EON) data service
Use this feature to receive the EON (enhanced other
networks) data service of the Radio Data System station
network. Once you select one of the 4 Radio Data System
program types (NEWS, AFFAIRS, INFO, or SPORT), this
unit automatically searches for all the available preset
stations that are scheduled to broadcast the EON data
service of the selected program type for a certain duration
of time. When the scheduled EON data service starts, this
unit automatically switches to the local station
broadcasting the EON data service and then switches back
to the national station once the EON data service ends.
Notes
• You can use this feature only when the EON data service is
available.
• The EON indicator lights up in the front panel display only
when the EON data service is being received from a Radio Data
System station.
1
Tune into the desired Radio Data System
broadcasting station.
2
Make sure the EON indicator is lit in the front
panel display.
If the EON indicator is not lit in the front panel
display, select another Radio Data System program so
that the EON indicator lights up.
EON
3
Press 0 EON on the remote control
repeatedly to select one of the 4 Radio Data
System program types (NEWS, AFFAIRS,
INFO or SPORT).
The name of the selected program type appears in the
front panel display.
NEWS
Lights up
y
To cancel the EON feature, press 0 EON on the remote
control repeatedly until the name of the program type
disappears and “EON OFF” appears in the front panel
display.
48 En
USING A USB MEMORY DEVICE OR A USB PORTABLE AUDIO PLAYER
Using a USB memory device or a USB portable audio player
Use this feature to enjoy WAV (PCM format only), MP3 and WMA files saved on your USB memory device or USB
portable audio player connected to the USB port on the front panel of this unit.
■ Supported USB devices
This unit supports USB mass storage class devices (except
USB hard disk drives) using FAT16 or FAT32 format.
Notes
• Only the first partition (32 GB or less) is displayed in the OSD.
You cannot select files in other partitions.
• Up to 8 levels of directory hierarchy and 500 music files per
directory are recognized.
• Some devices may not work properly even if they meet the
requirements.
• Some WAV, MP3 and WMA files may not be playable or may
be noisy when played.
Playback operation
Follow the procedures below to enjoy the music stored in
your USB device or a USB portable audio player.
1
Press O INPUT l / h repeatedly (or press
3 USB) to select USB.
The cursor on the left of the USB indicator lights up
in the front panel display, and the contents previously
played is automatically played.
Lights up
MULTI CH
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R
CD
BASIC
OPERATION
■ Connecting a USB memory device or a
USB potable audio player
TUNER
USB
INPUT:USB
Connect a USB jack of a USB memory device or
USB portable audio player to the USB port on the
front panel of this unit.
VOLUME
STANDBY/
ON
2
Press M DISPLAY to display the top USB file
list.
The USB file list appears in the OSD.
OPTIMIZER MIC
EDIT
PRESET/TUNING
BAND
l
A/B/C/D/E
PRESET/TUNING/CH
h
MEMORY
USB
Root
Ellis Margellis
Frankie Zipper
Hall in Call
Jackie Pastarius
Jmiel
Jean-Luc Ponta
Jim Hallo
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SILENT CINEMA
SPEAKERS
A/B/OFF
TONE CONTROL
PROGRAM
2
3
STRAIGHT
DIRECT
h
4
l
INPUT
VIDEO AUX
h
AUDIO SELECT
VIDEO
L
AUDIO
USB
R
EFFECT
USB
>
>
>
>
>
>
>
1/7
y
USB memory device
or USB portable
audio player
• “i” in the right corner of each menu line indicates that
there is a submenu available in the next menu level.
• When this unit is in the top directory, “Root” appears
beside “USB”.
English
49 En
Using a USB memory device or a USB portable audio player
3
4
Press 7 k / n / l / h on the remote control
to select the desired file.
• Press 7 k / n to select the desired file/folder.
• Press 7 ENTER or 7 h to enter the selected
folder.
• Press 7 l to return to the previous folder level.
■ The function of the play information
display
USB
Press 7 ENTER to play the selected file.
y
• You can use 9 b / a to skip backward/forward and
9 h / s to start/stop playback independently from the menu
in the OSD.
• You can set the settings for repeat and shuffle mode by using the
“USB PLAY STYLE” parameters in “OPTION MENU” (see
page 66).
• You can select the display mode in the front panel display by
using “FL SCROLL” in “OPTION MENU” (see page 64).
[Play]
[1]
[2]
[3]
.
[4]
00:00
All
FrankieZipper
Made-to-orderaaaaaAA
;RoadtoIndiaaaAAAA
[5]
[6]
[7]
.A
[1] Name of the artist
[2] Name of the album
[3] Name of the song
[4] Elapsed time
Note
When the elapsed time exceed “99:59”, “--:--” appeared
instead of the time.
[5]
[6]
(playback) icon
All
(all repeat),
1
(single repeat) icons
When “REPEAT” of the “USB PLAY STYLE” in “OPTION
MENU” (see page 66) is set to “OFF”, no icon appears in the
top right corner while files or folders are being played.
[7]
(shuffle) icon
When “SHUFFLE” of the “USB PLAY STYLE” in
“OPTION MENU” (see page 66) is set to “OFF”, no icon
appears in the top right corner while files or holders are being
played.
50 En
USING IPOD™
Using iPod™
Once you have stationed your iPod in a Yamaha iPod universal dock (such as YDS-10, sold separately) connected to the
DOCK terminal of this unit (see page 19), you can enjoy playback of your iPod using the supplied remote control. You
can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression artifacts
(such as the MP3 format) stored on your iPod (see page 19).
Notes
• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.
• Some features may not be compatible depending on the model or the software version of your iPod.
y
• For a complete list of status messages that appear in the front panel display and in the OSD, see the “iPod” section in
“Troubleshooting” on page 78.
• Once your iPod is stationed in a Yamaha iPod universal dock, this unit begins signal transmission with your iPod.
• Once the connection between your iPod and this unit is complete, “iPod connected” appears in the front panel display and the DOCK
indicator lights up in the front panel display.
• Only the analog audio and video signals of your iPod are input at the DOCK terminal, and the analog audio signals can be output at the
analog AUDIO OUT (REC) jacks for recording.
You can control your iPod when “V-AUX” is selected as the input source. The operations of your iPod can be done with
the aid of the OSD of this unit (menu browse mode) or without it (simple remote mode).
■ Remote control operation
Before performing the following operations, press 3 V-AUX/
DOCK.
Button
7 ENTER
Function
Subsequent menu
k
Menu up
n
Menu down
l
Previous menu
h
Subsequent menu
9 ll
BASIC
OPERATION
Controlling iPod™
■ Controlling iPod in the simple remote
mode
You can perform the basic operations of your iPod (play,
stop, skip, etc.) using the supplied remote control without
the aid of the OSD of this unit.
y
• You can view the photos or video clips stored on your iPod
(some models only).
• Operations can be also done with the controls on your iPod.
Search backward (Press and hold)
hh
Search forward (Press and hold)
b
Skip backward
a
Skip forward
e
Pause (Menu browse mode)
Play/Pause (Simple remote mode)
p
Play (Menu browse mode)
Play/Pause (Simple remote mode)
K MENU
Previous menu
M DISPLAY
Display
English
51 En
Using iPod™
■ Controlling iPod in the menu browse
mode
You can perform the advanced operations of your iPod
using the supplied remote control when you connect this
unit and a monitor using the VIDEO connection. You can
browse the songs stored on your iPod in the OSD. Further,
you can change or adjust settings for your iPod to suit
your personal preferences.
y
• The name of the song being played also appears in the front
panel display according to the “FL SCROLL” parameter in
“OPTION MENU” (see page 64).
• You can select the amount of time the iPod menu and play
information is displayed in the OSD by using the “OSDSOURCE” in “OPTION MENU” (see page 64)
Notes
• Operations cannot be done with the controls on your iPod.
• The Yamaha logo appears in the display window of your iPod.
• There are some characters that cannot be displayed in the front
panel display or in the OSD of this unit. Those characters are
replaced with underscores “_”.
• The “Settings” parameters can be changed or adjusted only in
the OSD. Press 7 ENTER repeatedly to toggle between the
“Settings” parameter settings.
• You cannot browse the photos or video clips stored on your
iPod in the OSD. Use the simple remote mode to enjoy
watching the photos or video clips stored on your iPod.
1
Press 3 V-AUX/DOCK and then
M DISPLAY.
The following display appears in the OSD.
iPod
Playlists
Artists
Albums
Songs
Genres
Composers
Settings
Shuffle Shuffle
Use this feature to set this unit to play songs or albums in
random order.
Choices: Off, Songs, Albums
• Select “Off ” to deactivate this feature.
• Select “Songs” to set this unit to play songs in random
order.
• Select “Albums” to set this unit to play albums in
random order.
y
When “Shuffle” is set to a setting other than “Off ”, “
” appears
in the top right corner while songs or albums are being shuffled.
Repeat Repeat
Use this feature to set this unit to repeat one song or a
sequence of songs.
Choices: Off, One, All
• Select “Off ” to deactivate this feature.
• Select “One” to set this unit to repeat one song.
• Select “All” to set this unit to repeat a sequence of
songs.
y
When “Repeat” is set to a setting other than “Off ”, “ ” or “ ”
appears in the top right corner while one song or a sequence of
songs are being repeated.
1
■ The function of the play information
display
[1]
>
>
>
>
>
>
>
[4]
[5]
[6]
2
Press 7 k / n / l / h to navigate the iPod
menu and then press 7 ENTER to begin
playback of the selected song.
Choices: Playlists (playlists), Artists (artists), Albums
(albums), Songs (songs), Genres (genres),
Composers (composers), Settings (settings)
• Playlists > Songs
• Artists > Albums > Songs
• Albums > Songs
• Songs
• Genres > Artists > Albums > Songs
• Composers > Albums > Songs
• Settings > Shuffle, Repeat
iPod[Play]
1/9
FrankieZipper
Made-to-order
RoadtoIndia
||;;;;;;;;;;;;;;;;;;
0:51-7:44
All
[2]
[3]
Top
[1]
Playback status
[2]
Track number/total tracks
[3]
Artist name
[4]
Song title
[5]
Progress bar
[6]
Elapsed time
[7]
Shuffle and repeat icons
[8]
(playback),
forward) and
[9]
Name of the album
[10] Remaining time
52 En
All
(pausing),
(search
(search backward)
[7]
[8]
[9]
[10]
USING BLUETOOTH™ COMPONENTS
Using Bluetooth™ components
You can connect a Yamaha Bluetooth adapter (such as YBA-10, sold separately) to the DOCK terminal of this unit and
enjoy the music contents stored in your Bluetooth component (such as a portable music player) without wiring between
this unit and the Bluetooth component. You need to perform “pairing” the connected Bluetooth adapter and your
Bluetooth component in advance.
Pairing the Bluetooth™ adapter
and your Bluetooth™ component
Pairing must be performed when using a Bluetooth
component with the Bluetooth adapter connected to this
unit for the first time or if the pairing data has been
deleted. “Pairing” refers to the operation of registering a
Bluetooth component for Bluetooth communications.
Note
If the Bluetooth adapter is not connected to the DOCK
terminal of this unit, “No BT adapter” appears in the front
panel display.
Check that the Bluetooth component detects
the Bluetooth adapter.
If the Bluetooth component detects the Bluetooth
adapter, “YBA-10 YAMAHA” (example) appears in
the Bluetooth device list.
5
Select the Bluetooth adapter in the Bluetooth
device list and then enter the pass key
“0000” on the Bluetooth component.
When the pairing procedure is successful,
“Completed” appears in the front panel display.
y
• You only need the pairing operation for the first time that you
use the Bluetooth component with the Bluetooth adapter.
• Pairing requires operations on this unit and on the other
component with which Bluetooth communications are to be
established. If necessary, refer to the other component’s
operating instructions.
There are two pairing methods: pairing by using “START
PAIRING” in “SET MENU” and quick pairing.
■ Pairing by using “SET MENU”
Use this feature to perform pairing with the video monitor.
Select “START PAIRING” in “INPUT MENU”. See
page 62 for details.
■ Quick pairing
To ensure security, a time limit of 8 minutes is set for the
pairing operation. You are recommended to read and fully
understand all the instructions before starting.
1
Press OINPUT l / h repeatedly (or press
3V-AUX/DOCK) to select “V-AUX” as the
input source.
2
Turn on the Bluetooth component you want
to pair with.
3
Press and hold CBAND (or 6BAND) for 3
seconds.
Once the Bluetooth adapter starts pairing,
“Searching...” appears for a moment. While the
Bluetooth adapter is in the pairing mode, DOCK
indicator flashes in the front panel display.
Note
The Yamaha Bluetooth adapter can be paired with up to eight
Bluetooth components. When pairing is conducted successfully
with a ninth component and the pairing data is registered, the
pairing data for the least recently used other component is
cleared.
Playback of the Bluetooth™
component
1
Press OINPUT l / h repeatedly (or press
3V-AUX/DOCK) to select “V-AUX” as the
input source.
2
Start playback of your Bluetooth component.
When the connected Bluetooth adapter detects the
Bluetooth component, “BT connected” and the
DOCK indicator appears in the front panel display.
y
• When you press 7 ENTER, the connected Bluetooth adapter
searches and connect to the last connected Bluetooth
component. If the Bluetooth adapter cannot find the Bluetooth
component, “Not found” appears in the front panel display.
• To disconnect the Bluetooth adapter from the Bluetooth
component, press 8 RETURN.
To cancel the pairing, press CBAND (or 6BAND) again.
53 En
English
y
BASIC
OPERATION
4
RECORDING
Recording
Recording adjustments and other operations are performed from the recording components. Refer to the operating
instructions for those components.
Notes
• When this unit is set to the standby mode, you cannot record between other components connected to this unit.
• TONE CONTROL (see page 41) and VOLUME settings, speaker levels (see page 41) and the sound field programs (see page 38) do
not affect recorded material.
• The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded.
• Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if
your source component is connected to provide only digital signals, you cannot record the source.
• A given input source is not output on the same AUDIO OUT (REC) channel.
• The analog audio signals input at the DOCK terminal can be output at the analog AUDIO OUT (REC) jacks for recording.
• Once you have connected a recording component to this unit, keep the component turned on while using this unit. If the component is
turned off, this unit may distort the sound from other components.
• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright
laws.
y
Do a test recording before you start an actual recording.
If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture
itself may be disturbed due to those signals.
1
Turn on all the connected components.
2
Press O INPUT l / h repeatedly (or press
one of the input selector buttons (3)) to
select the source component you want to
record from.
54 En
3
Start playback on the selected source
component or select a broadcast station.
4
Start recording on the recording component.
SET MENU
SET MENU
You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ Auto setup
AUTO SETUP
Use this feature to automatically adjust speaker and system parameters (see page 24).
■ Manual setup MANUAL SETUP
Use this feature to manually adjust speaker and system parameters.
Sound menu 1 SOUND MENU
Parameter
Features
Page
Selects the size of each speaker, the speakers for low-frequency signal output, and the
crossover frequency, and the location of the front speakers connected to the FRONT B
terminals.
57
B)SP LEVEL
Adjusts the output level of each speaker.
59
C)SP DISTANCE
Adjusts the delay time of each speaker.
59
D)CENTER GEQ
Adjusts the tonal quality of the center speaker.
60
E)LFE LEVEL
Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.
60
F)DYNAMIC RANGE
Adjusts the dynamic range of Dolby Digital or DTS signals.
60
G)AUDIO SET
Adjusts the muting level, audio delay, maximum volume level and initial volume level.
60
H)HDMI SET
Selects whether to play back HDMI audio signals on this unit or on another HDMI
component connected to the HDMI OUT jack.
61
ADVANCED
OPERATION
A)SPEAKER SET
Input menu 2 INPUT MENU
Parameter
Features
Page
A)INPUT ASSIGNMENT
Assigns the input jacks of this unit according to the component to be used.
62
B)INPUT RENAME
Changes the name of the input source.
62
C)VOLUME TRIM
Adjusts the output volume of each input source.
63
D)DECODER MODE
Selects the decoder mode for the sources connected to the DIGITAL INPUT jacks on the
rear panel of this unit.
63
E)MULTI CH SET
Selects the video source played in the background of the sources input from the MULTI CH
INPUT jacks.
63
English
55 En
SET MENU
Option menu 3 OPTION MENU
Parameter
Features
Page
A)DISPLAY SET
Adjusts the brightness of the front panel display and the way in which the iPod information
is displayed.
64
B)MEMORY GUARD
Locks sound field program parameters and other “SET MENU” settings.
64
C)AUDIO SELECT
Designates the default audio input jack select setting for the input sources connected to the
DIGITAL INPUT jacks when you turn on the power of this unit.
65
D)PARAM. INI
Initializes the parameters of a group of sound field programs.
65
E)BLUETOOTH SET
Pair the connected Yamaha Bluetooth adapter (such as YBA-10, sold separately) with a
Bluetooth component (see page 53).
65
F)USB PLAY STYLE
Adjusts the playback style of a USB source.
66
■ Signal information
SIGNAL INFO
Use this feature to check audio signal information (see page 36).
Using SET MENU
3
Use the remote control to access and adjust each
parameter.
y
;MANUAL SETUP
You can change the “SET MENU” parameters while this unit is
reproducing sound.
1
. 1 SOUND MENU
2 INPUT MENU
3 OPTION MENU
Press 4 AMP and then press K MENU to
enter “SET MENU”.
The top “SET MENU” display appears in the OSD.
4
Press 7 k / n / l / h and 7 ENTER to select
and change the parameter.
• Press 7 k / n to select the desired menu or
parameter.
• Press 7 l / h to change the parameter value.
• Press 7 ENTER to enter the selected menu or to
confirm the parameter.
• Press 8 RETURN to return to the previous menu
level.
5
Press K MENU to exit from “SET MENU”.
TOPAMENU
. ;AUTO SETUP
.A;MANUAL SETUP
;SIGNAL INFO
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
Press 7 k / n to select “MANUAL SETUP”.
SET MENU
TOPAMENU
;AUTO SETUP
.A;MANUAL SETUP
;SIGNAL INFO
56 En
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
SET MENU
2
Press 7 ENTER to enter “MANUAL SETUP”.
The “MANUAL SETUP” display appears in the
OSD.
SET MENU
1 SOUND MENU
Use this menu to manually adjust any speaker settings or
compensate for video signal processing delays when using
LCD monitors or projectors.
;MANUAL SETUP
Front speakers FRONT SP
Choices: SMALL, LARGE
;MANUAL SETUP
1 SOUND MENU
1/2
1 SOUND MENU
2/2
. F)DYNAMIC RANGE
G)AUDIO SET
H)HDMI SET
1 SOUND MENU
A)SPEAKER SET
FRONT SP
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
p
. A)SPEAKER SET
B)SP LEVEL
C)SP DISTANCE
D)CENTER GEQ
E)LFE LEVEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
Woofer section of a speaker is 16 cm (6.5 in) or larger:
large
Woofer section of a speaker is smaller than 16 cm
(6.5 in): small
■ Speaker settings A)SPEAKER SET
SMALL
>LARGE
Use this feature to manually adjust any speaker settings.
FRONT B speaker setting FRONT B
Use this feature to select the location of the front speakers
connected to the FRONT B terminals.
Choices: FRONT, ZONE B
1 SOUND MENU
A)SPEAKER SET
FRONT B;;;;FRONT
• Select “FRONT” to turn on or off SPEAKERS A and B
when the speakers connected to the FRONT B
terminals are set in the main zone.
• Select “ZONE B” if the speakers connected to the
FRONT B terminals are set in another zone. If
SPEAKERS A is turned off and SPEAKERS B is
turned on, all the speakers including the subwoofer in
the main zone are muted and this unit outputs sound at
the FRONT B terminals only.
Notes
• If you connect headphones to the PHONES jack of this unit, the
sound is output from both headphones and the FRONT B
terminals when “FRONT B” is set to “ZONE B”.
• If a DSP program is selected when “FRONT B” is set to
“ZONE B”, this unit automatically enters the Virtual CINEMA
DSP mode (see page 39).
When the front speakers are small
Select “SMALL” (small).
Note
When “LFE/BASS OUT” is set to “FRONT” (see page 58), you
can select only “LARGE” in “FRONT SP”. If the value of
“FRONT SP” is set to a setting other than “LARGE” in advance,
this unit automatically changes the value to “LARGE”.
Center speaker CENTER SP
Choices: NONE, SML, LRG
1 SOUND MENU
ADVANCED
OPERATION
p
p
[ ]/[ ]:Up/Down
[p]/[[]:Select
When the front speakers are large
Select “LARGE” (large).
A)SPEAKER SET
CENTER SP
NONE >SML
LRG
When the center speaker is large
Select “LRG” (large).
When the center speaker is small
Select “SML” (small).
When you do not use the center speaker
Select “NONE” (none). The center channel signals are
directed to the front left and right speakers.
English
57 En
SET MENU
Surround left/right speakers
Choices: NONE, SML, LRG
SUR. L/R SP
1 SOUND MENU
A)SPEAKER SET
SUR. L/R SP
NONE >SML
Crossover CROSS OVER
Use this feature to select a crossover frequency of all the
speakers set to “SML” (or “SMALL”) in “SPEAKER
SET” (see pages 57). All frequencies below the selected
frequency will be sent to the subwoofer or front speakers
depending on the setting of “LFE/BASS OUT” in
“SPEAKER SET” (see pages 57).
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
LRG
1 SOUND MENU
When the surround speakers are large
Select “LRG” (large).
When the surround speakers are small
Select “SML” (small).
When you do not use the surround speakers
Select “NONE” (none). This unit is set to the Virtual
CINEMA DSP mode (see page 39).
LFE Bass out LFE/BASS OUT
Use this feature to select the speakers that output the LFE
(low-frequency effect) and the low-frequency signals.
Choices: SWFR, FRNT, BOTH
A)SPEAKER SET
CROSSOVER
FREQ;;;80Hz
Subwoofer phase SUBWOOFER PHASE
Use this feature to switch the phase of your subwoofer if
bass sounds are lacking or unclear.
Choices: NORMAL, REVERSE
1 SOUND MENU
A)SPEAKER SET
SUBWOOFER PHASE
1 SOUND MENU
A)SPEAKER SET
LFE/BASS OUT
SWFR FRNT>BOTH
When a subwoofer is connected to this unit
and you want to get natural bass sound
Select “SWFR” (subwoofer). The LFE signals as well
as the low-frequency signals of other speakers set to
“SML” (or “SMALL”) are directed to the subwoofer.
When a subwoofer is connected to this unit
and you want to get rich bass sound
Select “BOTH” (both). The low-frequency signals of
any source are output from the subwoofer. The LFE
signals as well as the low-frequency signals of other
speakers set to “SML” (or “SMALL”) are directed to
the subwoofer. The low-frequency signals of the front
left and right channels are directed to the front left and
right speakers and the subwoofer regardless of the
“FRONT SP” setting (see page 57).
When you do not use a subwoofer
Select “FRNT” (front). The LFE signals, the lowfrequency signals of the front left and right channels,
and the low-frequency signals of other speakers set to
“SML” (or “SMALL”) are all directed to the front left
and right speakers regardless of the “FRONT SP”
setting (see page 57).
58 En
>NORMAL
REVERSE
• Select “NORMAL” if you do not want to reverse the
phase of your subwoofer.
• Select “REVERSE” to reverse the phase of your
subwoofer.
SET MENU
■ Speaker level B)SP LEVEL
Use this feature to manually adjust the output level of each
speaker.
Control range: –10 to +10 dB
Control step: 1 dB
Initial setting: 0 dB
1 SOUND MENU
1 SOUND MENU
B)SP LEVEL
1/2
-__________+
. FR.L
FR.R
CNTR
SWFR
B)SP LEVEL
2/2
-__________+
.SUR.L
SUR.R
■ Speaker distance C)SP DISTANCE
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
1 SOUND MENU
C)SP DISTANCE
Front left speaker
FR.R
Front right speaker
CNTR
Center speaker
SWFR
Subwoofer
SUR.L
Surround left speaker
SUR.R
Surround right speaker
The available speaker channels differ depending on the setting of
the speakers.
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting:
[U.S.A. and Canada models]: feet (ft)
[Other models]: meters (m)
• Select “meters” to adjust speaker distances in meters.
• Select “feet” to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting:
FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft)
CENTER: 2.60 m (8.5 ft)
SUR. L/SUR. R: 2.40 m (8.0 ft)
SP DISTANCE
ADVANCED
OPERATION
Note
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
p
FR.L
2/2
. SUR. L;;;;;2.40m
SUR. R;;;;;2.40m
p
p
Adjusted speaker
C)SP DISTANCE
. UNIT;;;;;;meters
FRONT L;;;;3.00m
FRONT R;;;;3.00m
CENTER;;;;;2.60m
SWFR;;;;;;;3.00m
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
p
SP LEVEL
1 SOUND MENU
1/2
Adjusted speaker
FRONT L
Front left speaker
FRONT R
Front right speaker
CENTER
Center speaker
SWFR
Subwoofer
SUR. L
Surround left speaker
SUR. R
Surround right speaker
Note
The available speaker channels differ depending on the setting of
the speakers.
English
59 En
SET MENU
■ Center speaker equalizer D)CENTER GEQ
Use this feature to adjust the built-in 5-frequency band
(100 Hz, 300 Hz, 1 kHz, 3 kHz and 10 kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Control range: –6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0 dB
F)DYNAMIC RANGE
0dB
0dB
0dB
0dB
0dB
p
p
Choices: OFF, ON
• Select “OFF” to stop test tones and output the currently
selected source component.
• Select “ON” to output test tones from the center and
front left speakers.
■ Low-frequency effect level E)LFE LEVEL
E)LFE LEVEL
. SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
p
p
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
Speaker SPEAKER
Adjusts the speaker LFE level.
Headphone HEADPHONE
Adjusts the headphone LFE level.
Note
Depending on the settings of “LFE/BASS OUT” (see page 58),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
Headphone HEADPHONE
Adjusts the headphone compression.
Choices: MIN, STD, MAX
• Select “MIN” (minimum) if you regularly listen at low
volume levels.
• Select “STD” (standard) for general use.
• Select “MAX” (maximum) to preserve the greatest
amount of dynamic range.
■ Audio settings G)AUDIO SET
Use this feature to adjust the overall audio settings of this
unit.
1 SOUND MENU
G)AUDIO SET
. MUTE TYPE;;;FULL
A.DELAY;;;;;;0ms
MAX VOL.;;;+16dB
INIT.VOL.;;;;OFF
[ ]/[ ]:Up/Down
[p]/[[]:Select
p
1 SOUND MENU
Speaker SPEAKER
Adjusts the speaker compression.
p
Use this feature to adjust the output level of the LFE (lowfrequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective when the input
signal contains the LFE channel.
Control range: –20 to 0 dB
Control step: 1 dB
p
p
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
Test tone TEST
Use this feature to make adjustments for “CENTER GEQ”
while listening to a test tone.
60 En
1 SOUND MENU
. SPEAKER;;;;;;MAX
HEADPHONE;;;;MAX
1 SOUND MENU
D)CENTER GEQ
TEST >OFF ON
. 100Hz ;;;;;;
300Hz ;;;;;;
1kHz ;;;;;;
3kHz ;;;;;;
10kHz ;;;;;;
[ ]/[ ]:Up/Down
[p]/[[]:Adjust
■ Dynamic range F)DYNAMIC RANGE
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
Mute type MUTE TYPE
Use this feature to adjust how much the mute function
reduces the output volume (see page 35).
Choices: FULL, –20dB
• Select “FULL” to completely mute all the audio
output.
• Select “–20dB” to reduce the current volume by 20 dB.
Audio delay A.DELAY
Use this feature to delay the sound output and synchronize
it with the video image. This may be necessary when
using certain LCD monitors or projectors.
Control range: 0 to 160 ms
Control step: 1 ms
SET MENU
Maximum volume MAX VOL.
Use this feature to set the maximum volume level. This
feature is useful to avoid the unexpected loud sound by
mistake. For example, the original volume range is –80 dB
to +16 dB. However, when “MAX VOL.” is set to –5 dB,
the volume range becomes –80 dB to –5 dB.
■ HDMI set H)HDMI SET
Use this feature to select the component to play back
HDMI audio signals.
1 SOUND MENU
H)HDMI SET
Control range: –30 dB to +10 dB, +16 dB
Control step: 5 dB
SUPPORT AUDIO:
RX-V463
[p]/[[]:Select
[ENTER]:Return
Note
The “MAX VOL.” setting takes priority over the “INIT.VOL.”
setting. For example, if “INIT.VOL.” is set to –20 dB and “MAX
VOL.” is set to –30 dB, the volume level is automatically set to
–30 dB when you turn on the power of this unit next time.
Initial volume INIT.VOL.
Use this feature to set the volume level when the power of
this unit is turned on.
Choices: OFF, MUTE, –80 dB to +16 dB
Control step: 1 dB
Support audio SUPPORT AUDIO
Use this feature to select whether to play back HDMI
audio signals on this unit or on another HDMI component
connected to the HDMI OUT jack on the rear panel of this
unit.
Choice
RX-V463
Plays back HDMI audio signals on this unit. The
HDMI audio signals input at the HDMI input
jacks of this unit are not output to the HDMI
component connected to the HDMI OUT jack on
the rear panel of this unit.
Other
Plays back HDMI audio signals on another
HDMI component connected to the HDMI OUT
jack.
Note
The “MAX VOL.” setting takes priority over the “INIT.VOL.”
setting.
Functions
• This unit transmits audio and video signals input at the HDMI
input jacks to the HDMI out jack only when this unit is turned
on even if “SUPPORT AUDIO” is set to “Other”.
• Available audio/video signals depend on the specification of the
connected video monitor. Refer to the instruction manual of
each connected component.
ADVANCED
OPERATION
Notes
English
61 En
SET MENU
2 INPUT MENU
Use this menu to reassign the input jacks, select the
decoder mode or rename the input source.
For HDMI jacks 1 and 2
HDMI IN [1]
HDMI IN [2]
Choices: [1] DVD, DTV/CBL, V-AUX, DVR
[2] DVD, DTV/CBL, V-AUX, DVR
;MANUAL SETUP
2 INPUT MENU
2 INPUT MENU
A)INPUT ASSIGNMENT
HDMI IN
. [IN1];;; DVD
( DVD
)
[IN2];;;DTV/CBL
(DTV/CBL )
p
p
. A)INPUT ASSIGNMENT
B)INPUT RENAME
C)VOLUME TRIM
D)DECODER MODE
E)MULTI CH SET
[ ]/[ ]:Up/Down
[ENTER]:Enter
[p]/[[]:Select
■ Input assignment
A)INPUT ASSIGNMENT
Use this feature to assign the input jacks according to the
component to be used if the initial settings of this unit do
not correspond to your needs. Change the following
parameters to reassign the respective jacks and effectively
connect more components.
Once the input jacks are reassigned, you can select the
corresponding component by using OINPUT l / h (or
the input selector buttons (3)).
2 INPUT MENU
B)INPUT RENAME
DVD
Press one of the input selector buttons (3)
or D MULTI CH IN to select the input
source you want to change the name of.
USB
A)INPUT ASSIGNMENT
COAXIAL IN
DVD
DVD
p
1
2 INPUT MENU
. (1);;;;;
(
-> DVD
[p]/[[]:Position
[ ]/[ ]:Chara.
p
For COAXIAL INPUT jack 1
COAXIAL IN (1)
Choices: (1) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
■ Input rename B)INPUT RENAME
Use this feature to change the name of the input source
that appears in the OSD and in the front panel display.
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
)
or
MULTI CH IN
[p]/[[]:Select
V-AUX/DOCK
For OPTICAL INPUT jacks 2 and 3
OPTICAL IN (2)
OPTICAL IN (3)
Choices: (2) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
(3) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
2 INPUT MENU
A)INPUT ASSIGNMENT
OPTICAL IN
. (2);;;;;DTV/CBL
(DTV/CBL )
(3);;;;;
CD
(
CD
)
[p]/[[]:Select
Note
You cannot select a specific item more than once.
62 En
2
Press 4 AMP and then press 7 l / h on the
remote control to place the “_” (underscore)
under the space or the character you want to
edit.
3
Press 7 k / n to select the character you
want to use and then press 7 l / h to move
to the next space.
Notes
• You can use up to 8 characters for each input.
• Press 7 n to change the character in the following order,
or press 7k to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, symbols (#,
*, –, +, etc.)
SET MENU
4
Repeat steps 1 through 3 to rename each
input source.
5
Press 7 ENTER to exit from “INPUT
RENAME”.
■ Volume trim C)VOLUME TRIM
Use this feature to adjust the output volume of each
source. This is useful if you want to balance the level of
each input source to avoid sudden changes in volume
when switching between input sources.
Choices: CD, MD/CD-R, TUNER, DVD,
DTV/CBL, V-AUX, DVR, DOCK, USB,
MULTI CH
Control range: –6.0 to +6.0 dB
Control step: 1.0 dB
Initial setting: 0.0 dB
2 INPUT MENU
DTS decoder prioritize setting
Choices: AUTO, DTS
• Select “AUTO” if you want this unit to automatically
detect input signal types and select the appropriate
input mode.
• Select “DTS” when you play back a DTS-CD.
■ Multi channel input setup
E)MULTI CH SET
2 INPUT MENU
E)MULTI CH SET
BGV;;;;;;;;;LAST
[p]/[[]:Select
Background Video BGV
Use this feature to select the video source played in the
background of the sources input at the MULTI CH INPUT
jacks.
Choices: DVD, DTV/CBL, V-AUX, DVR, LAST
C)VOLUME TRIM
DVD
DVD
;;;;;0.0dB
y
Select “LAST” to set this unit to automatically select the last
selected video source as the background video source.
[p]/[[]:Adjust
[RETURN]:Exit
ADVANCED
OPERATION
Note
You can only adjust the value for DOCK when your iPod is
stationed in the Yamaha Universal Dock connected to this unit.
■ Decoder mode D)DECODER MODE
2 INPUT MENU
D)DECODER MODE
.
>AUTO
CD
DVD
DTV/CBL
LAST
;;;;AUTO
;;;;AUTO
;;;;AUTO
p
p
[ ]/[ ]:Up/Down
[p]/[[]:Select
Decoder select mode
Use this feature to designate the default decoder mode for
the input sources connected to the DIGITAL INPUT jacks
when you turn on the power of this unit.
Choices: AUTO, LAST
• Select “AUTO” if you want this unit to automatically
detect the type of input signals and select the
appropriate decoder mode.
• Select “LAST” if you want this unit to automatically
select the last decoder mode used the connected input
source.
English
63 En
SET MENU
3 OPTION MENU
Use this menu to adjust the optional system parameters.
;MANUAL SETUP
;MANUAL SETUP
3 OPTION MENU
1/2
3 OPTION MENU
2/2
. F)USB PLAY STYLE
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
p
. A)DISPLAY SET
B)MEMORY GUARD
C)AUDIO SELECT
D)PARAM. INI
E)BLUETOOTH SET
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ Display settings A)DISPLAY SET
3 OPTION MENU
A)DISPLAY SET
p
p
. DIMMER;;;;;;;;;0
FL SCROLL;;;CONT
OSD SHIFT;;;;;;0
OSD-SOURCE;;;30s
OSD-AMP;;;;;;30s
[ ]/[ ]:Up/Down
[p]/[[]:Select
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
Control range: –4 to 0
Control step: 1
• Press 7 l to make the front panel display dimmer.
• Press 7 h to make the front panel display brighter.
Front panel display scroll FL SCROLL
Use this feature to set whether to display the information
(such as a song title or a channel name) in the front panel
display in a continuous manner or by the first 14
alphanumeric characters after scrolling all characters once
when “DOCK” is selected as the input source.
Choices: CONT, ONCE
• Select “CONT” to display the operation status in the
front panel display in a continuous manner.
• Select “ONCE” to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
OSD shift OSD SHIFT
Use this feature to adjust the vertical position of the OSD.
Control range: –5 (downward) to +5 (upward)
Control step: 1
Initial setting: 0
• Press 7 l to lower the position of the OSD.
• Press 7 h to raise the position of the OSD.
64 En
Source feature OSD display time
OSD-SOURCE
Use this feature to set the amount of time to display the
iPod menu in the OSD after you perform a certain
operation.
Choices: ON, 10s, 30s
• Select “ON” to display the OSD unceasingly during an
operation.
• Select “10s” to turn off the OSD 10 seconds after you
perform a certain operation.
• Select “30s” to turn off the OSD 30 seconds after you
perform a certain operation.
Amplifier function OSD display time
OSD-AMP
Use this feature to set the amount of time to display the
status after you perform a certain operation.
Choices: ON, 10s, 30s
• Select “ON” to display the OSD constantly during an
operation.
• Select “10s” to turn off the OSD 10 seconds after you
perform a certain operation.
• Select “30s” to turn off the OSD 30 seconds after you
perform a certain operation.
■ Memory guard B)MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: OFF, ON
3 OPTION MENU
B)MEMORY
>OFF
GUARD
ON
[p]/[[]:Select
• Select “OFF” to turn off the “MEMORY GUARD”
feature.
• Select “ON” to protect:
– sound field program parameters
– all “SET MENU” items
– all speaker levels
– SCENE template parameters
Note
When “MEMORY GUARD” is set to “ON”, you cannot select
and adjust any other “SET MENU” items.
SET MENU
■ Audio select
C)AUDIO SELECT
Use this feature to designate the default audio input jack
select setting for the input sources when you turn on the
power of this unit.
Choices: AUTO, LAST
■ Bluetooth setting E)BLUETOOTH SET
3 OPTION MENU
E)BLUETOOTH SET
. START PAIRING
3 OPTION MENU
C)AUDIO SELECT
>AUTO
LAST
[p]/[[]:Select
• Select “AUTO” if you want this unit to automatically
detect the type of input signals and select the
appropriate input mode.
• Select “LAST” if you want this unit to automatically
select the last input mode used for the connected input
source (see page 34).
■ Parameter initialization D)PARAM. INI
Use this feature to set all the parameters of the sound field
programs to the initial factory settings.
Choices: NO, YES
3 OPTION MENU
[ENTER]:Enter
Use this feature to start pairing the connected Yamaha
Bluetooth adapter (such as YBA-10, sold separately) with
your Bluetooth component. For details about the pairing,
refer to “Pairing the Bluetooth™ adapter and your
Bluetooth™ component” on page 53.
To ensure security, a time limit of 8 minutes is set for
the pairing operation. You are recommended to read
and fully understand all the instructions before starting.
Press 7 ENTER to start pairing.
The connected Bluetooth adapter starts searching
Bluetooth components. “Searching...” appears in the
video monitor.
2
Check that the Bluetooth component detects
the Bluetooth adapter.
If the Bluetooth component the Bluetooth adapter,
“YBA-10 YAMAHA” (example) appears in the
Bluetooth device list.
3
Select the Bluetooth adapter in the Bluetooth
device list and then enter the pass key
“0000” on the Bluetooth component.
Once this unit completes the pairing successfully,
“Pairing completed” appears.
D)PARAM. INI
>NO
YES
[p]/[[]:Select
[ENTER]:Return
• Select “NO” to cancel the parameter initialization and
return to the previous menu screen.
• Select “YES” and press 7 ENTER to set all the sound
field parameters to the initial factory settings.
Notes
• You cannot automatically revert to the previous parameter
settings once you initialize the sound field program parameters.
• You cannot separately initialize individual sound field
programs.
• You cannot initialize any sound field program groups when
“MEMORY GUARD” is set to “ON”.
ADVANCED
OPERATION
1
y
To cancel the pairing, press 8 RETURN to exit from
“START PAIRING”.
4
Press 8RETURN to exit from “START
PAIRING”.
Notes
• If the connected Bluetooth adapter cannot find any Bluetooth
components, “Not found” appears.
• If a Bluetooth adapter is not connected to this unit, “No BT
adapter” appears.
English
65 En
SET MENU
■ USB playback styles F)USB PLAY STYLE
Use this feature to adjust the playback style according to
your preference. You can shuffle files in a random order or
repeat one specific file or a sequence of files.
3 OPTION MENU
F)USB PLAY STYLE
. REPEAT.......OFF
SHUFFLE......OFF
p
p
[ ]/[ ]:Up/Down
[p]/[[]:Select
Repeat REPEAT
Use this feature to set this unit to repeat one file or a
sequence of files.
Choices: OFF, SINGLE, ALL
• Select “OFF” to deactivate this feature.
• Select “SINGLE” to set this unit to repeat one file.
• Select “ALL” to set this unit to repeat a sequence of
files.
Shuffle SHUFFLE
Use this feature to set this unit to play files or folders in a
random order.
Choices: OFF, ON
• Select “OFF” to deactivate this feature.
• Select “ON” to set this unit to play files or folders in a
random order.
66 En
Remote control features
Remote control features
In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha
and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code
for each input source (see page 69).
Controlling this unit, a TV, or other components
■ Controlling this unit
■ Controlling a TV
Press 4 AMP to control this unit.
POWER
POWER
STANDBY
POWER
TV
AV
USB
A
B
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
C
D
AMP
TV INPUT
TV MUTE
*1
DTV/CBL
TV VOL
AMP
SCENE
1
2
BAND LEVEL
TITLE
POWER
POWER
STANDBY
POWER
TV
AV
USB
A
B
MUTE
CD
MD/CD-R
TUNER
TV CH
DVR
V-AUX/DOCK
Press 3 DTV/CBL to control your TV. To control your
TV, you must set the appropriate remote control code for
DTV/CBL (see page 69).
3
DVD
DTV/CBL
DVR
V-AUX/DOCK
C
D
AMP
TV INPUT
TV MUTE
1
2
TV CH
*1
TV VOL
4
SCENE
VOLUME
MENU
BAND LEVEL
TITLE
3
4
VOLUME
MENU
ENTER
ENTER
DISPLAY
RETURN
MEMORY
*2
REC
DISPLAY
RETURN
MEMORY
REC
FREQ/TEXT
l
EON
PROG h
MODE - PTY SEEK - START
3
4
NIGHT
PARAMETER
6
7
8
MULTI CH IN AUDIO SEL
0
10
FREQ/TEXT
SLEEP
ENT
EON
MODE - PTY SEEK - START
l
PROG h
1
2
3
4
STRAIGHT
DIRECT
NIGHT
PARAMETER
5
6
ENHANCER SUR. DECODE
7
MULTI CH IN AUDIO SEL
9
0
ADVANCED
OPERATION
2
DIRECT
5
9
*2
ENHANCER SUR. DECODE
1
STRAIGHT
10
8
SLEEP
ENT
Notes
*1
These buttons always control this unit.
*2 These buttons control this unit only when 4 AMP is pressed.
Notes
*1
These buttons always control your TV regardless of whether
you press 3 DTV/CBL or not.
Remote control
*2
Digital TV/Cable TV
TV POWER
Turns on or off the power.
TV CH +/–
Changes the channel number.
TV VOL +/–
Increases or decreases the volume
level.
TV INPUT
Changes the input source.
TV MUTE
Mutes the audio output.
These buttons control your TV only when 3 DTV/CBL is
pressed. For details, see the “Digital TV/Cable TV” column on
page 68.
y
67 En
English
You can control more than one TV by setting the appropriate
remote control code for any input source selector buttons other
than 3 DTV/CBL. In such a case, you can control the buttons
highlighted above (*1 and *2) when you press the input source
selector button.
Remote control features
■ Controlling other components
Press one of the input selector buttons (3) or A to D
buttons to control other components. You must set the
appropriate remote control code for each input source in
advance (see page 69). The following table shows the
function of each control button used to control other
components assigned to each input selector button. Be
advised that some buttons may not correctly operate the
selected component.
[1]
[2]
POWER
POWER
TV
AV
USB
STANDBY
POWER
A
B
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
C
D
AMP
TV INPUT
TV MUTE
TV CH
BAND LEVEL
TITLE
[3]
[4]
MENU
• The remote control has 13 modes (input areas) to control
components so that the remote control can operate up to 13
different components.
• When you press one of the optional component control area
buttons (A to D), you can control the desired component
without changing the input source of this unit.
RETURN
MEMORY
[5]
TV VOL
SCENE
1
2
3
4
FREQ/TEXT
[6]
EON
MODE - PTY SEEK - START
l
PROG h
1
2
3
4
STRAIGHT
DIRECT
NIGHT
PARAMETER
5
6
7
ENHANCER SUR. DECODE
MULTI CH IN AUDIO SEL
9
0
Digital TV/
Cable TV
LD player
CD player
MD/CD
recorder
[1] AV POWER
Power *1
Power *2
Power *1
Power *1
Power *1
[2] TITLE
Title
[3] PRESET/CH k
[8]
DISPLAY
DVD player/
VCR
recorder
Power *1
[7]
ENTER
REC
y
Remote control
VOLUME
10
8
SLEEP
ENT
[9]
Tuner
Band
Up
VCR channel up Up
Preset up (1-8)/
Tuning up
PRESET/CH n
Down
VCR channel
down
Down
Preset down
(1-8)/Tuning
down
A/B/C/D/E l
Left
Left
Preset down
(A-E)
A/B/C/D/E h
Right
Right
Preset up
(A-E)
Enter
Enter
Hold
[4] RETURN
ENTER
Return
Return
Memory
[5] REC
Disc skip
(player)
Rec (recorder)
Rec
Rec *2
p
Play
Play
Play *2
w
Search
backward
Search backward
Search backward Search backward Search backward Information
Search backward
*2
f
Search forward
Search forward
Search forward
*2
Search forward
Search forward
Search forward
e
Pause
Pause
Pause *2
Pause
Pause
Pause
b
Skip backward
Skip backward
Skip backward
*2
Skip backward
Skip backward
Skip backward
Audio program
down
a
Skip forward
Skip forward
Skip forward *2 Skip forward
Skip forward
Skip forward
Audio program
up
s
Stop
Stop
Stop *2
Stop
Stop
[6] 1-9, 0, +10
Play
Stop
Disc skip
Rec
Play
Play
Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons
Preset stations
(1-8)
[7] MENU
Menu
Search mode
[8] DISPLAY
Display
Display
Display
Display
Display
Display
Display
[9] ENT
Title/Index
Enter
Enter
Chapter/Time
Index
Index
Enter
Menu
Notes
*1
*2
This button is operational only when the original remote control supplied with the component has a POWER button.
These buttons operate your DVD recorder only when you set the appropriate remote control code for DVR (see page 69).
68 En
Remote control features
Setting remote control codes
1
You can control other components by setting the
appropriate remote control codes. For a complete list of
available remote control codes, refer to “List of remote
control codes” at the end of this manual.
While pressing and holding one of the input
selector buttons (3) on the remote control to
select the input area you want to set up,
press 2 AV POWER for more than 3
seconds.
USB
A
B
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
C
D
Remote control code default settings
Input
source
Component
category
Manufacturer
Default
code
CD
Yamaha
5013
MD/CD-R
CD-R
Yamaha
5001
TUNER
TUNER
Yamaha
5007
DVD
DVD
Yamaha
2000
DTV/CBL
—
—
—
V-AUX
TUNER
Yamaha
5011
DVR
DVR
Yamaha
2011
USB
TUNER
Yamaha
5012
A
TUNER
Yamaha
5009
B
TUNER
Yamaha
5017
C
TUNER
Yamaha
5009
D
TUNER
Yamaha
5017
AV
Press for 3
seconds
While holding down
2
Press the numeric buttons (0 to 9) (F) to
enter the four-digit remote control code for
the component to be used.
When the setting succeeds, “RemoteSetup OK”
appears; however, when it does not, “RemoteSetup
NG” appears in the front panel display.
Notes
• If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
• If you do not press any buttons within 30 seconds in step 2, the
setup process is canceled. If this happens, repeat the setup
procedure.
Note
ADVANCED
OPERATION
CD
POWER
You may not be able to operate your Yamaha component even if a
Yamaha remote control code is preset as listed above. In this case,
try setting another Yamaha remote control code.
English
69 En
Advanced setup
Advanced setup
This unit has additional menus that are displayed in the
front panel display. The advanced setup menu offers
additional operations to adjust and customize the way this
unit operates. Change the initial settings (indicated in bold
under each parameter) to reflect the needs of your
listening environment.
Notes
• Only ASTANDBY/ON, L PROGRAM l / h and
M STRAIGHT are effective while you are using the advanced
setup menu.
• No other operations can be made while you are using the
advanced setup menu.
• The advanced setup menu is only available in the front panel
display.
1
Press A STANDBY/ON to set this unit to the
standby mode.
2
Press and hold K TONE CONTROL and
then press A STANDBY/ON to turn on this
unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
3
Press L PROGRAM l / h to select the
parameter you want to adjust.
The name of the selected parameter appears in the
front panel display.
4
Press M STRAIGHT repeatedly to change
the selected parameter setting.
5
Press A STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
y
The settings you made are reflected next time you turn on this
unit.
70 En
■ Tuner frequency step TU
(Asia and General models only)
Use this feature to set the tuner frequency step according
to the frequency spacing in your area.
Choices: AM10/FM100, AM9/FM50
• Select “AM10/FM100” for North, Central and South
America.
• Select “AM9/FM50” for all other areas.
■ Initializing INIT.
Use this feature to reset all the parameters of this unit to
the initial factory settings (see page 80).
Choices: CANCEL, RESET
• Select “CANCEL” not to reset any parameters of this
unit.
• Select “RESET” to reset the parameters of this unit.
Notes
• This setting completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
Troubleshooting
Troubleshooting
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
■ General
Problem
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
No sound.
Cause
Remedy
See
page
Connect the power cable firmly.
—
The protection circuitry has been
activated.
Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wire
for each connection does not touch anything other
than its respective connection.
11
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and then
use it normally.
—
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
13-18
No appropriate Audio input jack select has
been set.
Set an appropriate Audio input jack select.
34
Audio input jack select is set to “HDMI”,
“COAX/OPT” or “ANALOG”.
Set Audio input jack select to “AUTO”.
34
Audio input jack select is set to
“ANALOG” while playing a source
encoded in Dolby Digital or DTS.
Set Audio input jack select to “AUTO” or
“COAX/OPT”.
34
No appropriate input source has been
selected.
Select an appropriate input source with OINPUT
l / h (or the input selector buttons(3)).
33
Speaker connections are not secure.
Secure the connections.
11
The front speakers to be used have not
been selected properly.
Select the front speakers with JSPEAKERS.
33
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press IMUTE or L VOLUME +/– to resume audio
output and then adjust the volume.
35
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
The HDMI components connected to this
unit do not support the HDCP copy
protection standards.
Connect HDMI components that support the HDCP
copy protection standards.
14
“SUPPORT AUDIO” is set to “Other” and
“HDMI” audio signals are not being
played back on this unit.
Set “SUPPORT AUDIO” to “RX-V463” in
“MANUAL SETUP”.
61
ADDITIONAL
INFORMATION
The power cable is not connected or the
plug is not completely inserted.
English
71 En
Troubleshooting
Problem
The sound suddenly
goes off.
Cause
Remedy
See
page
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned off this unit.
Turn on this unit, and play the source again.
—
The sound is muted.
Press IMUTE or L VOLUME +/– to resume audio
output.
35
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
11-18
Incorrect settings in “SP LEVEL”.
Adjust the “SP LEVEL” settings.
41
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
This is not malfunction.
—
No sound is heard
from the center
speaker.
“CENTER SP” in “SPEAKER SET” is set
to “NONE”.
Set “CENTER SP” to “SML” or “LRG”.
57
Some sound field programs do not output
sounds from the center speaker.
Try another sound field program.
38
No sound is heard
from the surround
speakers.
“SUR. L/R SP” in “SPEAKER SET” is
set to “NONE”.
Set “SUR. L/R SP” to “SML” or “LRG”.
58
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
Press B STRAIGHT so that “STRAIGHT”
disappears from the front panel display.
39
No sound from the
center, surround
speakers when the
FRONT B speakers
are activated.
“FRONT B” in “SPEAKER SET” is set to
“ZONE B”.
Set “FRONT B” to “FRONT”.
57
No sound is heard
from the subwoofer.
“LFE/BASS OUT” in “SPEAKER SET”
is set to “FRNT” when a Dolby Digital or
DTS signal is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
58
“LFE/BASS OUT” in “SPEAKER SET”
is set to “SWFR” or “FRNT” when a 2channel source is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
58
The source does not contain lowfrequency bass signals.
This is not malfunction.
—
72 En
Troubleshooting
Problem
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
Cause
Remedy
See
page
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
Audio input jack select is set to
“ANALOG”.
Set Audio input jack select to “AUTO”.
34
A humming sound is
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
—
The volume level
cannot be increased,
or the sound is
distorted.
You are attempting to set the volume level
higher than the maximum volume level.
Adjust “MAX VOL.” setting.
61
The component connected to the AUDIO
OUT (REC) jacks of this unit is turned
off.
Turn on the power of the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
This is not malfunction.
—
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jacks.
The source component is not connected to
the analog AUDIO IN jacks of this unit.
Connect the source component to the analog AUDIO
IN jacks.
The sound field
parameters and some
other settings of this
unit cannot be
changed.
“MEMORY GUARD” in “OPTION
MENU” is set to “ON”.
Set “MEMORY GUARD” to “OFF”.
64
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
—
No sound is heard
from the connected
HDMI component.
The HDMI component does not accept the
multi-channel audio signals.
Convert the multi-channel audio signals to the 2channel audio signals at the source component such
as a DVD player.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
11
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to the digital or highfrequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This in not malfunction.
—
This unit suddenly
enters the standby
mode.
The internal temperature is too high and
the overheat protection circuitry has been
activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
14, 18
ADDITIONAL
INFORMATION
English
73 En
Troubleshooting
■ Tuner
Problem
FM stereo reception is
noisy.
FM
AM
74 En
Cause
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Remedy
See
page
Check the antenna connections.
20
Try using a high-quality directional FM
antenna.
—
Use the manual tuning method.
43
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
Adjust the antenna position to eliminate
multi-path interference.
—
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is too weak.
Use a high-quality directional FM antenna.
—
Use the manual tuning method.
43
Previously preset
stations can no longer
be tuned into.
This unit has been disconnected for a
long period.
Set preset stations.
44
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for the best reception.
—
Use the manual tuning method.
43
There are continuous
crackling and hissing
noises.
Noise can result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV set.
—
Troubleshooting
■ AUTO SETUP
Before AUTO SETUP
Error message
Cause
Remedy
See
page
Connect MIC!
Optimizer microphone is not connected.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
24
Unplug HP!
Headphones are connected.
Unplug the headphones.
—
During AUTO SETUP
Error message
Cause
Remedy
See
page
E-1:NO FRONT SP
Front L/R channel signals are not detected.
Check the front L/R speaker connections.
11
E-2:NO SUR.SP
A surround channel signal is not detected.
Check the surround speaker connections.
11
E-4:NOISY
Background noise is too loud.
Try running “AUTO SETUP” in a quiet
environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the
optimizer microphone.
—
E-6:NO MIC
The optimizer microphone was unplugged
during the “AUTO SETUP” procedure.
Connect the supplied optimizer microphone
to OPTIMIZER MIC jack on the front
panel.
24
E-7:NO SIGNAL
The optimizer microphone does not detect
test tones.
Check the microphone setting.
24
Check the speaker connections and
placement.
10, 11,
24
The “AUTO SETUP” procedure was
cancelled due to user activity.
Run “AUTO SETUP” again.
24
E-9:INTERNAL ERROR
An internal error occurred.
Run “AUTO SETUP” again.
24
ADDITIONAL
INFORMATION
E-8:USER CANCEL
English
75 En
Troubleshooting
After AUTO SETUP
Warning message
Cause
Remedy
See
page
W-1:OUT OF PHASE
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the speaker connections for proper
polarity (+ or –).
12
W-2:OVER 24m (80ft)
The distance between the nearest speaker
and the furthest speaker is out of adjustable
range.
Bring the speaker closer to the listening
position.
—
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive. (No level correction
is made.)
If “SWFR:TOO LOUD” or “SWFR:TOO
LOW” appears, adjust the output volume of
the subwoofer.
24, 59
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
—
Check the speaker connections.
11
Use speakers of similar quality.
—
Notes
• If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.
• If a warning message “W-1”, “W-2”, or “W-3” appears, corrections are made, but they may not be optimal.
• If an error message “E-9” occurs repeatedly, please contact a qualified Yamaha service center.
76 En
Troubleshooting
■ USB
Cause
The music files and
directories in the USB
device cannot be
viewed.
The music files and directories are placed
in locations other than the FAT area.
Place music files and directories in the FAT area.
—
You are attempting to browse directory
hierarchies of over 8 levels or a directory
with more than 500 files.
Modify the data structure on your USB device.
—
The connected USB device is other than a
USB mass storage class USB memory
device or USB portable audio player.
This unit can recognize only a USB mass storage
class USB memory device (except USB hard disk
drives) or USB portable audio player. Also note that it
cannot recognize certain USB devices even when they
are devices as described above.
49
Some devices may become easier to recognize when
they are inserted before turning this unit on.
21
Turn this unit off then on again.
21
The USB device
cannot be recognized.
“Disconnected” is
displayed even when
a USB device is
present.
This unit recognized the USB device as an
illegal device.
Status message
Cause
Disconnected
Access error
Remedy
See
page
Your USB memory device or USB
portable audio player has been
disconnected from the USB port of this
unit.
Check the connection between this unit and your
USB memory device or USB portable audio player.
—
There is a problem with the signal path
from your USB memory device or USB
portable audio player to this unit.
Turn off this unit and reconnect your USB memory
device or USB portable audio player to the USB port
of this unit.
49
Try resetting your USB memory device or USB
portable audio player.
—
This unit cannot access your USB
memory device or USB portable audio
player.
Try another USB memory device or USB portable
audio player.
—
There is a problem with the signal path
from your USB memory device or USB
portable audio player to this unit.
Turn off this unit and reconnect your USB memory
device or USB portable audio player to the USB port
of this unit.
49
Try resetting your USB memory device or USB
portable audio player.
—
Try another USB memory device or USB portable
audio player.
—
No varied data is detected.
ADDITIONAL
INFORMATION
Unable to play
Remedy
See
page
Problem
English
77 En
Troubleshooting
■ iPod
Note
In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod
(see page 19).
Status message
Loading...
Cause
Remedy
See
page
This unit is in the middle of recognizing
the connection with your iPod.
This unit is in the middle of acquiring
song lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to this unit.
Turn off this unit and reconnect the Yamaha iPod
universal dock to the DOCK terminal of this unit.
19
Try resetting your iPod.
—
Only iPod (Click and Wheel), iPod nano, and iPod
mini are supported.
—
Unknown iPod
The iPod being used is not supported by
this unit.
iPod connected
Your iPod is properly stationed in a
Yamaha iPod universal dock (YDS-10,
sold separately) connected to the DOCK
terminal of this unit, and the connection
between your iPod and this unit is
complete.
Disconnected
Your iPod was removed from a Yamaha
iPod universal dock (YDS-10, sold
separately) connected to the DOCK
terminal of this unit.
Station your iPod back in a Yamaha iPod universal
dock (YDS-10, sold separately) connected to the
DOCK terminal of this unit.
19
Unable to play
This unit cannot play back the songs
currently stored on your iPod.
Check that the songs currently stored on your iPod
are playable.
—
Store some other playable music files on your iPod.
—
78 En
Troubleshooting
■ Bluetooth
Status message
Searching...
Cause
Remedy
See
page
The Bluetooth adapter and the Bluetooth
component is in the middle of the pairing.
The Bluetooth adapter and the Bluetooth
component is in the middle of establishing
the connection.
Completed
The paring is completed.
Canceled
The paring is canceled.
BT connected
The connection between the Yamaha
Bluetooth adapter (such as YBA-10, sold
separately) and the Bluetooth component
is established.
Disconnected
The Bluetooth component is disconnected
from the Yamaha Bluetooth adapter (such
as YBA-10, sold separately).
No BT adapter
The Bluetooth adapter is not connected to
the DOCK terminal.
Connect the Yamaha Bluetooth adapter (such as
YBA-10, sold separately) to the DOCK terminal.
19
ADDITIONAL
INFORMATION
English
79 En
Troubleshooting
■ Remote control
Problem
The remote control
does not work nor
function properly.
Cause
Remedy
See
page
Wrong distance or angle.
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
23
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
3
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
69
Try setting another code for the same manufacturer
using “List of remote control codes” at the end of this
manual.
69
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
■ Resetting the system
Use this feature to reset all the parameters of this unit to
the initial factory settings.
1
Press A STANDBY/ON on the front panel to
set this unit to the standby mode.
2
Press and hold K TONE CONTROL and
then press A STANDBY/ON to turn on this
unit.
The advanced setup menu appears in the front panel
display.
3
Press L PROGRAM l / h to select “INIT.”.
4
Press M STRAIGHT repeatedly to select
“RESET”.
Select “CANCEL” to cancel the initialization
procedure without making any changes.
5
Press A STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
80 En
Notes
• This procedure completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
y
To cancel the initialization procedure at any time without making
any changes, press M STRAIGHT repeatedly to select
“CANCEL” and then press A STANDBY/ON.
Glossary
Glossary
■ CINEMA DSP
■ Dolby Pro Logic II
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers designed for
acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it is inevitable that there are differences in
the sound heard. Based on a wealth of actually measured
data, Yamaha CINEMA DSP uses Yamaha original sound
field technology to combine Dolby Pro Logic, Dolby
Digital and DTS systems to provide the audiovisual
experience of a movie theater in the listening room of your
own home.
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround sources.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels instead of
only 1 surround channel for conventional Pro Logic
technology. There are three modes available: “Music
mode” for music sources, “Movie mode” for movie
sources and “Game mode” for game sources.
■ Dolby Surround
■ Composite video signal
■ DTS Digital Surround
With the composite video signal system, the video signal
is composed of three basic elements of a video picture:
color, brightness and synchronization data. A composite
video jack on a video component transmits these three
elements combined.
DTS digital surround was developed to replace the analog
soundtracks of movies with a 5.1-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. DTS, Inc. has developed a
home theater system so that you can enjoy the depth of
sound and natural spatial representation of DTS digital
surround in your home. This system produces practically
distortion-free 5.1-channel sound (technically, left, right
and center channels, 2 surround channels, plus an LFE 0.1
channel as a subwoofer, for a total of 5.1-channels).
■ Component video signal
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (front L/R and center), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (Low Frequency Effect), the system
has a total of 5.1-channels (LFE is counted as 0.1
channel). By using 2-channel stereo for the surround
speakers, more accurate moving sound effects and
surround sound environment are possible than with Dolby
Surround. The wide dynamic range from maximum to
minimum volume reproduced by the 5 full-range channels
and the precise sound orientation generated using digital
sound processing provide listeners with unprecedented
excitement and realism. With this unit, any sound
environment from monaural up to a 5.1-channel
configuration can be freely selected for your enjoyment.
ADDITIONAL
INFORMATION
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the PB
and PR signals for the chrominance. Color can be
reproduced more faithfully with this system because each
of these signals is independent. The component signal is
also called the “color difference signal” because the
luminance signal is subtracted from the color signal. A
monitor with component input jacks is required in order to
output component signals.
Dolby Surround uses a 4-channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range. Dolby Surround
is widely used with nearly all video tapes and laser discs,
and in many TV and cable broadcasts as well. The Dolby
Pro Logic decoder built into this unit employs a digital
signal processing system that automatically stabilizes the
volume on each channel to enhance moving sound effects
and directionality.
English
81 En
Glossary
■ HDMI
HDMI (High-Definition Multimedia Interface) is the first
industry-supported, uncompressed, all-digital audio/video
interface. Providing an interface between any source (such
as a set-top box or AV receiver) and an audio/video
monitor (such as a digital television), HDMI supports
standard, enhanced or high-definition video as well as
multi-channel digital audio using a single cable. HDMI
transmits all ATSC HDTV standards and supports 8channel digital audio, with bandwidth to spare to
accommodate future enhancements and requirements.
When used in combination with HDCP (High-bandwidth
Digital Content Protection), HDMI provides a secure
audio/video interface that meets the security requirements
of content providers and system operators. For further
information on HDMI, visit the HDMI website at
“http://www.hdmi.org/”.
■ LFE 0.1 channel
This channel reproduces low-frequency signals. The
frequency range of this channel is from 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low-frequency range compared to the full-range
reproduced by the other 5 channels in Dolby Digital or
DTS 5.1-channel systems.
■ MP3
One of the audio compression methods used by MPEG. It
employs the irreversible compression method, which
achieves a high compression rate by thinning out the data
of hardly audible part to the human ears. It is said to be
capable of compressing the data quantity by about 1/11
(128 kbps) while maintaining a similar audio quality to
music CD.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “Pulse Code
Modulation”, the analog signal is encoded as pulses and
then modulated for recording.
82 En
■ Sampling frequency and number of
quantized bits
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits. The range of rates that can
be played back is determined based on the sampling rate,
while the dynamic range representing the sound level
difference is determined by the number of quantized bits.
In principle, the higher the sampling frequency, the wider
the range of frequencies that can be played back, and the
higher the number of quantized bits, the more finely the
sound level can be reproduced.
■ SILENT CINEMA
Yamaha has developed a natural, realistic sound effect
DSP algorithm for headphones. Parameters for
headphones have been set for each sound field so that
accurate representations of all the sound field programs
can be enjoyed on headphones.
■ Virtual CINEMA DSP
Yamaha has developed a Virtual CINEMA DSP algorithm
that allows you to enjoy DSP sound field surround effects
even without any surround speakers by using virtual
surround speakers. It is even possible to enjoy Virtual
CINEMA DSP using a minimal two-speaker system that
does not include a center speaker.
■ WAV
Windows standard audio file format, which defines the
method of recording the digital data obtained by
converting audio signals. It does not specify the
compression (coding) method so a desired compression
method can be used with it. By default, it is compatible
with the PCM method (no compression) and some
compression methods including the ADPCM method.
■ WMA
An audio compression method developed by Microsoft
Corporation. It employs the irreversible compression
method, which achieves a high compression rate by
thinning out the data of hardly audible part to the human
ears. It is said to be capable of compressing the data
quantity by about 1/22 (64 kbps) while maintaining a
similar audio quality to music CD.
Specifications
Specifications
AUDIO SECTION
• Minimum RMS Output Power for Front, Center, Surround
[U.S.A. and Canada models]
1 kHz, 0.9% THD, 8 Ω .................................................... 105 W
[Other models]
1 kHz, 0.9% THD, 6 Ω .................................................... 105 W
• Signal Level
Composite ................................................................. 1 Vp-p/75 Ω
Component ................... 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (PB/PR)
• Signal to Noise Ratio ................................................ 50 dB or more
• Maximum Input Level........................................... 1.5 Vp-p or more
• Maximum Power for Front, Center, Surround (JEITA)
[Asia, General, China, and Korea models]
1 kHz, 10% THD, 6 Ω ..................................................... 130 W
• Frequency Response (MONITOR OUT)
Component Signal .................................... 5 Hz to 60 MHz, –3 dB
• Dynamic Power
[U.S.A. and Canada models]
(IHF, 8/6/4/2 Ω) ............................................ 90/110/130/150 W
[Other models]
(IHF, 6/4/2 Ω) .................................................... 100/110/125 W
• Tuning Range
[U.S.A. and Canada models] ........................... 87.5 to 107.9 MHz
[Asia and General models] ........ 87.5/87.50 to 108.0/108.00 MHz
[Other models] ............................................ 87.50 to 108.00 MHz
• Dynamic Headroom [U.S.A. and Canada models]
8 Ω .................................................................................... 0.27 dB
• Maximum Input Signal
CD, etc. Effect On, 1 kHz, 0.5% THD ................... 2.0 V or more
• Frequency Response
CD, etc. to Front L/R ............................. 10 Hz to 100 kHz, –3 dB
• Total Harmonic Distortion
[U.S.A. and Canada models]
(1 kHz, 45 W, Front L/R, 8 Ω ) ............................. 0.06% or less
[Other models]
(1 kHz, 50 W, Front L/R, 6 Ω ) ............................. 0.06% or less
• Signal to Noise Ratio (IHF-A Network)
CD (200 mV) to Front L/R, Effect Off ................... 98 dB or more
CD (250 mV) to Front L/R, Effect Off ................. 100 dB or more
• Residual Noise (IHF-A Network)
Front L/R ............................................................... 150 µV or less
• Channel Separation (1 kHz/10 kHz)
CD, etc. (5.1 kΩ shorted) to Front L/R
................................................................... 60 dB/45 dB or more
• Headphone Jack Rated Output/Impedance .............. 400 mV/470 Ω
• Input Sensitivity/Input Impedance
CD, etc. ................................................................. 200 mV/47 kΩ
MULTI CH INPUT ............................................... 200 mV/47 kΩ
• Output Level/Output Impedance
AUDIO OUT (REC) ............................................ 200 mV/1.2 kΩ
SUBWOOFER OUTPUT ............................................ 4 V/1.2 kΩ
• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F.
(FRONT SP, CENTER SP, SUR. L/R SP:
SMALL/SML) ............................................................ 12 dB/oct.
L.P.F. (Subwoofer) ......................................................... 24 dB/oct.
• 50 dB Quieting Sensitivity (IHF, 100% mod.)
Mono ................................................................. 2.8 µV (20.2 dBf)
• Signal to Noise Ratio (IHF)
Mono/Stereo .............................................................. 73 dB/70 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo ................................................................ 0.5%/0.5%
• Antenna Input (unbalanced) ..................................................... 75 Ω
AM SECTION
• Tuning Range
[U.S.A. and Canada models] .............................. 530 to 1710 kHz
[Asia and General models] ................. 530/531 to 1710/1611 kHz
[Other models] ................................................... 531 to 1611 kHz
GENERAL
• Power Supply
[Europe, and Russia models] ............................. 230 V AC, 50 Hz
[U.S.A. and Canada models] ............................. 120 V AC, 60 Hz
[Australia model] .............................................. 240 V AC, 50 Hz
[Korea model] ................................................... 220 V AC, 60 Hz
[China model] .................................................... 220 V AC, 50 Hz
[Asia model] ................................... 220/230-240 V AC, 50/60 Hz
[General model] .............. 110/120/220/230-240 V AC, 50/60 Hz
• Power Consumption
[U.S.A. and Canada models] ................................. 240 W/320 VA
[Other models] ................................................................... 240 W
• Standby Power Consumption ................................................. 0.8 W
• Maximum Power Consumption [Asia and General models only]
5ch, 10% THD ................................................................... 440 W
ADDITIONAL
INFORMATION
• Tone Control (Front L/R)
BASS Boost/Cut ................................................... ±10 dB/100 Hz
TREBLE Boost/Cut .............................................. ±10 dB/20 kHz
FM SECTION
• Dimensions (W x H x D) ................................. 435 x 151 x 352 mm
(17-1/8” x 5-15/16” x 13-7/8”)
• Weight ............................................................. 8.5 kg (18 lbs 12 oz)
* Specifications are subject to change without notice.
VIDEO SECTION
• Video Signal Type (Gray back)
[U.S.A., Canada, Korea and General models] .................... NTSC
[Other models] ....................................................................... PAL
English
83 En
INDEX
Index
■
Numerics
1 SOUND MENU, Manual setup ........ 55
2 INPUT MENU, Manual setup .......... 55
2ch Enhancer,
Sound field program ........................ 38
2ch Stereo, Sound field program ......... 38
3 OPTION MENU ............................... 64
3 OPTION MENU, Manual setup ....... 56
5ch Enhancer,
Sound field program ........................ 38
5ch Stereo, Sound field program ......... 38
■
A
A)DISPLAY SET, Option menu ......... 64
A)INPUT ASSIGNMENT,
Input menu ....................................... 62
A)SPEAKER SET, Sound menu ......... 57
A.DELAY, Audio settings ................... 60
AFFAIRS, Radio Data System program
type .................................................. 47
AM antenna connection ....................... 20
AM tuning ............................................ 43
Amplifier function OSD display time,
Display settings ............................... 64
Audio components, Connection ........... 18
Audio delay, Audio settings ................. 60
Audio information ................................ 36
Audio input jacks selection .................. 34
AUDIO jacks ....................................... 13
Audio jacks .......................................... 13
AUDIO SELECT ................................. 34
Audio select, Option menu .................. 65
Audio settings, Sound menu ................ 60
Audio signal flow ................................. 14
AUTO SETUP ..................................... 24
AUTO SETUP, Error message ............ 75
Automatic preset tuning,
FM/AM tuning ................................. 44
Automatic tuning, FM/AM tuning ....... 43
■
B
B)INPUT RENAME, Input menu ....... 62
B)MEMORY GUARD,
Option menu .................................... 64
B)SPEAKER LEVEL,
Sound menu ..................................... 59
Background Video,
Multi channel input setup ................ 63
BGV, Multi channel input setup .......... 63
Bluetooth setting, Option menu ........... 65
BT connected,
Bluetooth status message ................. 79
■
C
C)AUDIO SELECT, Option menu ...... 65
C)SP DISTANCE, Sound menu .......... 59
C)VOLUME TRIM, Input menu ......... 63
Canceled, Troubleshooting .................. 79
CD player, Connection ........................ 18
CD recorder, Connection ..................... 18
84 En
CENTER SP, Speaker settings .............57
Center speaker equalizer,
Sound menu .....................................60
Center speaker, Speaker settings ..........57
Center width,
Sound field parameter ......................40
CINEMA DSP indicator ......................23
CLASSICS, Radio Data System program
type ...................................................47
Clock time, Radio Data System
information .......................................46
COAXIAL IN (1), Input assignment ...62
COAXIAL INPUT assignment,
Input assignment ..............................62
COAXIAL INPUT jacks ......................62
Completed,
Bluetooth status message .................79
COMPONENT VIDEO jacks ..............13
Connect error, iPod controlling status
message ............................................78
Connect MIC!,
Auto setup error message .................75
Connecting to the FRONT A
terminals ...........................................12
Connection, AM antenna connection ...20
Connection, Audio components ...........18
Connection, CD player .........................18
Connection, CD recorder .....................18
Connection, DVD player ......................16
Connection, DVD recorder ..................17
Connection, external decoder ...............18
Connection, FM antenna ......................20
Connection, HDMI ...............................14
Connection, MD recorder ....................18
Connection, Multi-format player .........18
Connection, Power cable ......................20
Connection, PVR .................................17
Connection, set-top boxes ....................17
Connection, VCR .................................17
Connection, Video components ...........15
Connection,
Yamaha iPod universal dock ...........19
Controlling a TV ..................................67
Controlling other components, Remote
control ..............................................68
Controlling this unit, Remote control ..67
Creating original SCENE templates ....31
CROSSOVER, Speaker settings ..........58
Crossover, Speaker settings .................58
CT indicator .........................................23
CT WIDTH, Sound field parameter .....40
CT, Radio Data System information ....46
CULTURE, Radio Data System program
type ...................................................47
Current status display ...........................35
■
D
D)CENTER GEQ, Sound menu ...........60
D)DECODER MODE, Input menu .....63
D)PARAM. INI, Option menu .............65
Decoder indicators ............................... 22
Decoder mode, Input menu ................. 63
Decoder select mode, Decoder mode .. 63
DIGITAL AUDIO COAXIAL jacks ... 13
DIGITAL AUDIO OPTICAL jacks .... 13
DIMENSION,
Sound field parameter ..................... 40
Dimension, Sound field parameter ...... 40
DIMMER, Display settings ................. 64
Dimmer, Display settings .................... 64
DIRECT ............................................... 41
Disconnected,
Bluetooth status message ................ 79
Disconnected, iPod controlling status
message ........................................... 78
Display settings, Option menu ............ 64
DIST .................................................... 26
DIST, Auto setup result ....................... 26
DISTANCE ......................................... 25
DISTANCE, Auto setup ...................... 25
DOCK indicator .................................. 22
DRAMA, Radio Data System program
type .................................................. 47
DSP LEVEL, Sound field parameter .. 40
DSP level, Sound field parameter ....... 40
DTS decoder prioritize setting,
Decoder mode ................................. 63
DVD player connection ....................... 16
DVD recorder connection ................... 17
Dynamic range, Sound menu .............. 60
■
E
E)LFE LEVEL, Sound menu .............. 60
E)MULTI CH SET, Input menu .......... 63
E-1:NO FRONT SP,
Auto setup error message ................ 75
E-2:NO SURR.SP,
Auto setup error message ................ 75
E-4:NOISY,
Auto setup error message ................ 75
E-6:NO MIC,
Auto setup error message ................ 75
E-7:NO SIGNAL,
Auto setup error message ................ 75
E-8:USER CANCEL,
Auto setup error message ................ 75
E-9:INTERNAL ERROR,
Auto setup error message ................ 75
EDUCATE, Radio Data System program
type .................................................. 47
Effect level, Sound field parameter ..... 40
Enhanced other networks data service,
Radio Data System tuning ............... 48
ENHANCER indicator ........................ 22
EON data service, Radio Data System
tuning ............................................... 48
EON indicator ...................................... 23
Exchange, Preset station,
FM/AM tuning ................................ 45
External decoder connection ............... 18
Index
■
F
F)DYNAMIC RANGE,
Sound menu ..................................... 60
Factory presets, Advanced setup ......... 70
FL SCROLL, Display settings ............. 64
FM antenna .......................................... 20
FM antenna connection ........................ 20
FM tuning ............................................ 43
FRONT B speaker setting,
Speaker settings ............................... 57
FRONT B, Speaker settings ................. 57
Front panel display ............................... 22
Front panel display scroll,
Display settings ................................ 64
FRONT SP, Speaker settings ............... 57
Front speakers, Speaker settings .......... 57
Low-frequency effect level,
Sound menu .....................................60
LVL ......................................................26
LVL, Auto setup result .........................26
■
M
H) HDMI SET, Sound menu ............... 61
Hall, Sound field program ................... 38
HDMI indicator .................................... 22
HDMI set, Sound menu ....................... 61
HDMI, Connection .............................. 14
HEADPHONE, Dynamic range .......... 60
Headphone, Dynamic range ................. 60
HEADPHONE,
Low-frequency effect level .............. 60
Headphone,
Low-frequency effect level .............. 60
Headphones .......................................... 35
Headphones indicator .......................... 22
M.O.R. M, Radio Data System program
type ...................................................47
Manual preset tuning,
FM/AM tuning .................................44
MANUAL SETUP, SET MENU .........55
Manual setup, SET MENU ..................55
Manual tuning, FM/AM tuning ............43
MAX VOL., Audio settings .................61
Maximum volume, Audio settings .......61
MD recorder, Connection .....................18
Memory guard, Option menu ...............64
Menu browse mode,
iPod controlling ................................52
Movie Dramatic,
Sound field program ........................38
Movie Spacious,
Sound field program ........................38
MULTI CH INPUT component
selection ...........................................34
Multi channel input setup,
Input menu .......................................63
Multi-channel source
with headphones ...............................39
Multi-format player connection ...........18
Multi-information display ....................23
MUTE ..................................................35
MUTE indicator ...................................22
MUTE TYPE, Audio settings ..............60
Muting ..................................................35
■
■
■
G
G)AUDIO SET, Sound menu .............. 60
Games, Sound field program ............... 38
■
H
I
■
J
Jazz, Sound field program ................... 38
■
L
■
O
OPTICAL IN (2),
Input assignment ..............................62
OPTICAL IN (3),
Input assignment ..............................62
OPTICAL INPUT assignment,
Input assignment ..............................62
OPTIMIZER MIC jack,
Auto setup ........................................24
Optimizer microphone .........................24
Optimizer microphone,
Auto setup ........................................24
Optimizing speaker setting ...................24
Option menu, Manual setup .................56
OSD SHIFT, Display settings ..............64
OSD shift, Display settings ..................64
OSD-AMP, Display settings ................64
OSD-SOURCE, Display settings .........64
P
PANORAMA,
Sound field parameter ..................... 40
Panorama,
Sound field parameter ..................... 40
Parameter initialization,
Option menu .................................... 65
PCM indicator ..................................... 22
PHONES jack ...................................... 35
Play information display,
iPod controlling ............................... 52
Play information display,
USB controlling ............................... 50
Playing video sources
in the background ............................ 36
PLII Game ........................................... 39
PLII Movie .......................................... 39
PLII Music ........................................... 39
POP M, Radio Data System
program type ................................... 47
Pop/Rock, Sound field program .......... 38
Power cable, Connection ..................... 20
Preset SCENE templates ..................... 30
Preset station exchange,
FM/AM tuning ................................ 45
Preset station selection,
FM/AM tuning ................................ 45
PRESET, Advanced setup ................... 70
Pro Logic ............................................. 39
Program service, Radio Data System
information ...................................... 46
Program type, Radio Data System
information ...................................... 46
PS indicator ......................................... 23
PS, Radio Data System information .... 46
PTY HOLD indicator .......................... 23
PTY indicator ...................................... 23
PTY SEEK mode, Radio Data System
tuning ............................................... 47
PTY, Radio Data System information . 46
Pure hi-fi sound ................................... 41
PVR connection ................................... 17
■
R
Radio Data System indicator ............... 23
Radio Data System tuning ................... 46
Radio text, Radio Data System
information ...................................... 46
Remote control codes ........................... iii
Remote control, Troubleshooting ........ 80
Rename, SCENE template ................... 31
Repeat .................................................. 52
Repeat, iPod controlling ...................... 52
Resetting the system ............................ 80
ROCK M, Radio Data System program
type .................................................. 47
RT indicator ......................................... 23
85 En
English
LFE/BASS OUT, Speaker settings ...... 58
LFE/Bass out, Speaker settings ........... 58
LIGHT M, Radio Data System program
type .................................................. 47
Loading...,
iPod controlling status message ....... 78
N
NEWS, Radio Data System
program type ....................................47
Night listening mode ............................42
No BT Adapter,
Bluetooth status message .................79
Number of speakers ..............................26
Number of speakers,
Auto setup result ..............................26
■
ADDITIONAL
INFORMATION
INFO, Radio Data System
program type .................................... 47
Infrared window, Remote control ........ 23
INI.VOL., Audio settings .................... 61
Initial volume, Audio settings .............. 61
Input assignment, Input menu .............. 62
Input channel and speaker indicators ... 23
Input channel indicators ....................... 23
Input menu, Manual setup ................... 55
Input rename, Input menu .................... 62
Input source indicators ......................... 22
Input source information display ......... 36
iPod connected, iPod controlling status
message ............................................ 78
iPod control, Status message ............... 78
iPod using ............................................ 51
Other components controlling by remote
control .............................................. 68
Other components controlling, Remote
control .............................................. 68
OTHER M, Radio Data System program
type .................................................. 47
Index
RT, Radio Data System information .... 46
■
S
SCENE 1 ................................................ 7
SCENE template selection ................... 28
SCIENCE, Radio Data System program
type .................................................. 47
Searching...,
Bluetooth status message ................. 79
Selection, Audio input jacks ................ 34
Selection, MULTI CH INPUT
component ....................................... 34
Selection, Preset station,
FM/AM tuning ................................. 45
Selection, Radio Data System program
type .................................................. 47
Selection, SCENE template ................. 28
SET MENU .......................................... 55
Setting remote control codes ................ 69
Setting SCENE template input source,
Remote control ................................ 32
Set-top box connection ........................ 17
Shuffle, iPod controlling ...................... 52
SILENT CINEMA ............................... 39
SILENT CINEMA indicator ................ 23
Simple remote mode,
iPod controlling ............................... 51
SIZE ..................................................... 25
SIZE, Auto setup .................................. 25
SLEEP indicator .................................. 23
Sleep timer ........................................... 37
Sound field programs
with headphones .............................. 39
Sound menu, Manual setup .................. 55
Source feature OSD display time,
Display settings ............................... 64
SP ......................................................... 26
SP A B indicators ................................. 22
SP, Auto setup result ............................ 26
Speaker distance ............................ 25, 26
Speaker distance, Auto setup ............... 25
Speaker distance, Auto setup result ..... 26
Speaker distance, Sound menu ............ 59
Speaker distances, Speaker distance .... 59
Speaker level ........................................ 26
Speaker level adjustment ..................... 41
Speaker level, Auto setup result .......... 26
Speaker level, Sound menu .................. 59
Speaker settings, Sound menu ............. 57
Speaker size ......................................... 25
Speaker size, Auto setup ...................... 25
Speaker wiring ..................................... 25
Speaker wiring, Auto setup .................. 25
Speaker wiring/volume level,
Auto setup ........................................ 25
SPEAKER, Dynamic range ................. 60
Speaker, Dynamic range ...................... 60
SPEAKER,
Low-frequency effect level .............. 60
Speaker, Low-frequency effect level ... 60
Specifications ....................................... 83
SPORT, Radio Data System
program type .................................... 47
STRAIGHT .......................................... 39
86 En
Straight .................................................39
SUBWOOFER PHASE,
Speaker settings ...............................58
Subwoofer phase, Speaker settings ......58
SUPPORT AUDIO, HDMI set ............61
Support audio, HDMI set .....................61
SUR. L/R SP, Speaker settings ............58
Surround left/right speakers,
Speaker settings ...............................58
■
T
Test tone, Center speaker equalizer .....60
TEST, Center speaker equalizer ...........60
Tonal quality adjustment ......................41
Troubleshooting ...................................71
TU, Advanced setup .............................70
Tuner (FM/AM),
Troubleshooting ...............................74
Tuner frequency step,
Advanced setup ................................70
Tuner indicators ...................................22
Turning off the power ..........................21
Turning on the power ...........................21
TV Sports, Sound field program ..........38
■
WIRING/LEVEL ................................ 25
WIRING/LEVEL, Auto setup ............. 25
■
Y
Yamaha iPod universal dock,
Connection ...................................... 19
Yamaha Parametric Room Acoustic
Optimizer ......................................... 24
YPAO .................................................. 24
YPAO (Yamaha Parametric Room
Acoustic Optimizer) ........................ 24
YPAO indicator ................................... 22
U
Unable to play, iPod controlling status
message ............................................78
UNIT, Speaker distance .......................59
Unit, Speaker distance ..........................59
Unknown iPod, iPod controlling status
message ............................................78
Unplug HP!,
Auto setup error message .................75
USB memory device using, USB portable
audio player using ............................49
USB playback operation ......................49
USB playback styles ............................66
USB, Troubleshooting .........................77
■
V
VARIED, Radio Data System program
type ...................................................47
VCR connection ...................................17
VIDEO AUX jacks, Front panel ..........19
Video components, Connection ...........15
Video information ................................36
VIDEO jacks ........................................13
Video jacks ...........................................13
Video signal flow .................................14
Video sources in the background .........36
Virtual CINEMA DSP .........................39
VIRTUAL indicator .............................23
VOLTAGE SELECTOR ........................3
VOLUME level indicator .....................22
Volume Trim, Input menu ...................63
■
W
W-1:OUT OF PHASE,
Auto setup error message .................76
W-2:DISTANCE ERROR,
Auto setup error message .................76
W-3:LEVEL ERROR,
Auto setup error message .................76
“JSPEAKERS” or “3DVD” (example)
indicates the name of the parts on the front
panel or the remote control. Refer to the
attached sheet or the pages at the end of this
manual for the information about each
position of the parts.
Limited Guarantee for European Economic Area (EEA) and Switzerland
Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from
whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our
website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).
The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha
undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge
for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been
discontinued or is considered uneconomic to repair.
Conditions
1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a
statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the
product may be returned at the customer’s expense.
2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.
3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.
4. The following are excluded from this guarantee:
a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.
b. Damage resulting from:
(1) Repairs performed by the customer himself or by an unauthorised third party.
(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to
ensure the product is adequately packaged when returning the product for repair.
(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper
use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in
the country where it is used.
(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.
(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.
(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety
standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.
(7) Non AV (Audio Visual) related products.
(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or
http://www.yamaha-uk.com/ for U.K. resident.)
5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.
6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the
product.
7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.
8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising
from their sales/purchase contract.
English
87 En
■
Front panel/Face avant/Frontblende/Frontpanelen/Voorpaneel/
Фронтальная панель
A
B
C
D
E
F GH
I
VOLUME
STANDBY
/ON
OPTIMIZER MIC
EDIT
PRESET/TUNING
BAND
l PRESET/TUNING/CH h
A/B/C/D/E
MEMORY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SPEAKERS
A/B/OFF
PROGRAM
TONE CONTROL
3
4
l
STRAIGHT
INPUT
DIRECT
VIDEO AUX
h
AUDIO SELECT
EFFECT
SILENT CINEMA
J
i
2
h
K
L
M N
O
P Q
VIDEO
L
AUDIO
USB
R
■
Remote control/Boîtier de télécommande/Fernbedienung/Fjärrkontrollen/
Afstandsbediening/Пульт ДУ
1
2
3
POWER
POWER
TV
AV
USB
STANDBY
POWER
A
B
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
C
D
AMP
TV INPUT
TV MUTE
G
H
I
TV CH
J
TV VOL
4
SCENE
5
6
1
2
BAND LEVEL
TITLE
7
8
3
4
VOLUME
MENU
L
ENTER
DISPLAY
RETURN
MEMORY
K
M
REC
9
0
l
EON
PROG h
MODE - PTY SEEK - START
ENHANCER SUR. DECODE
1
2
3
4
STRAIGHT
DIRECT
NIGHT
PARAMETER
5
6
7
MULTI CH IN AUDIO SEL
9
0
10
8
SLEEP
ENT
N
O
P
Q
R
APPENDIX
A
B
C
D
E
F
FREQ/TEXT
ii
List of remote control codes
Liste des codes de commande
Liste der Fernbedienungscodes
Lista över fjärrstyrningskoder
Lijst met afstandsbedieningscodes
Список кодов дистанционного управления
Blu-ray player
Samsung
2137
CD player
Yamaha
5000, 5013
CD Recorder
Yamaha
5001
DVD
Acoustic Solutions
2078
Aiwa
2055, 2100
Akai
2096
Akura
2076
Alba
2078, 2086
Apex
2027, 2049
Awa
2078
Axion
2078
Brainwave
2096
Brandt
2073, 2085
Broksonic
2060
Bush
2075, 2078, 2112
Centrex
2077
Classic
2078
Clatronic
2075
Coby
2078
C-Tech
2074
CyberHome
2025, 2079, 2091
Daewoo
2092, 2098
Dansai
2096
Daytek
2080, 2089
DEC
2075
Denon
2030, 2102, 2103
Denver
2075, 2076
Diamond
2074
DK Digital
2094
Dual
2078
D-Vision
2096
DVX
2074
Elta
2096
Euroline
2096
Funai
2052, 2058
Global Solutions2074
Global Sphere 2074
Goodmans
2075, 2077, 2078
Grundig
2077, 2098
H&B
2075
Haaz
2074
HE
2078
Hitachi
2032, 2072
Home Electronics
2078
Innovation
2072
Irradio
2134
JDB
2078
JVC
2033, 2045, 2053,
2073, 2099
Kenwood
2030, 2097
Kingavon
2075
Koda
2075
Lawson
2074
iii
Lenco
LG
Lifetec
Limit
LogicLab
Luxor
Magnavox
Magnum
MBO
Medion
Micromaxx
Micromedia
Microstar
Mitsubishi
Mizuda
Mustek
Naiko
Onkyo
Orava
P&B
Pacific
Panasonic
2075
2084, 2087
2072
2074
2074
2077
2037, 2073, 2075
2072
2078
2072
2072
2073
2072
2035
2075
2078
2077
2073, 2135
2075
2075
2074
2030, 2040, 2054,
2057, 2105, 2110
Philips
2019, 2026, 2046,
2073, 2081, 2090
Pioneer
2036, 2082
Proline
2077
Provision
2075
RCA
2031, 2042, 2050,
2051
Red Star
2076
Reoc
2074
Roadstar
2075, 2078, 2086
Rowa
2077
Saba
2085
Sabaki
2074
Samsung
2032, 2041, 2104,
2113
Sansui
2074
Sanyo
2095
ScanMagic
2078
Scientific Labs 2074
Scott
2088
SEG
2074, 2086
Sharp
2034, 2043, 2059,
2093, 2106
Silva
2076
Singer
2074
Skymaster
2074, 2078
Skyworth
2076
SM Electronic 2074, 2078
Sony
2028, 2029, 2039,
2083, 2107
Soundmaster
2074
Soundmax
2074
Standard
2074
Star Cluster
2074
Starmedia
2075
Supervision
2074, 2078
Sylvania
2052, 2058
Synn
2074
TCM
2072
Teac
2074
Tec
Technics
Technika
Technosonic
Tevion
Thomson
Tokai
Toshiba
United
Voxson
Wharfedale
Xlogic
Yakumo
Yamada
Yamaha
Yukai
Zenith
2076
2030
2096
2096
2072, 2074
2085, 2109
2076
2026, 2044, 2048,
2056, 2073, 2108,
2111
2078
2078
2074
2074
2077
2077
2000, 2001, 2003,
2030, 2101
2078
2038, 2047, 2073
DVD Recorder
Apex
JVC
LG
Panasonic
Philips
Pioneer
RCA
Sony
Toshiba
Yamaha
Yukai
2024
2070
2071
2020, 2065, 2066,
2067
2019, 2061, 2062,
2063
2021
2018
2022, 2064
2068
2023
2069
DVD/LD
Pioneer
2036
DVD/VCR
JVC
LG
Panasonic
Philips
RCA
Samsung
Sharp
Sony
Toshiba
Zenith
1017, 2045
1071, 2087
1020, 1072, 2040,
2105
1025
1022, 2042
1021, 2041, 2104
1023, 1073, 2043,
2106
1019, 1074, 2039,
2107
1024, 1075, 2044,
2108
1026, 2047
DVD-DVR
Panasonic
Pioneer
Samsung
Toshiba
2067
2114
2115
2068
2132
2132
2132
2123, 2128, 2129,
2133
DISH Network 2126, 2127
Dishpro
2126
Echostar
2126, 2127
Expressvu
2126
Gateway
2132
GOI
2126
Hewlett Packard 2132
Hitachi
2008
Howard Computers
2132
HTS
2126
Hughes
2123, 2128
Humax
2123
Hush
2132
iBUYPOWER 2132
JVC
2126, 2127
Linksys
2132
Media Center PC
2132
Microsoft
2132
Mind
2132
Niveus Media 2132
Northgate
2132
Panasonic
2015, 2016, 2017,
2120
Philips
2117, 2121, 2123,
2128
Pioneer
2012, 2013, 2014
Proscan
2129
RCA
2116, 2124, 2129,
2133
ReplayTV
2118, 2119, 2120
Sharp
2009, 2010
Sonic Blue
2119, 2120
Sony
2005, 2006, 2007,
2122, 2130, 2131,
2132
Stack 10
2132
Stack 9
2132
Systemax
2132
Tagar Systems 2132
Tivo
2116, 2121, 2122,
2123, 2130, 2131
Toshiba
2004, 2125, 2132
Touch
2132
UltimateTV
2133
Viewsonic
2132
Voodoo
2132
Yamaha
2011
ZT Group
2132
HD DVD
Toshiba
2132
2136
iPod
Yamaha
DVR
ABS
Alienware
CyberPower
Dell
DIRECTV
5011
LD player
Yamaha
2002
MD
Yamaha
5002, 5003, 5004
TAPE DECK
Yamaha
5005, 5006
TUNER
Yamaha
5007, 5008, 5009,
5010, 5012, 5014,
5015, 5016, 5017,
5018
TV
Acer
Acme
Acura
ADA
ADC
Admiral
Dantax
Daytron
De Graaf
Decca
0217
0060, 0061, 0208
0210
0204, 0207, 0213,
0217
Desmet
0213, 0217
Diamond
0200
Dimensia
0057
Dixi
0208, 0213, 0217
DTS
0208
Dual
0207, 0215, 0216
Dual-Tec
0207, 0208, 0215
Dumont
0060, 0127, 0205,
0207
Durabrand
0126
Dux
0217
Dynatron
0213, 0217
Elbe
0203, 0204, 0212,
0218
Elbe-Sharp
0204
Elcit
0204, 0205
ELECTRO TECH
0208
Electroband
0059
Electrohome
0059, 0060, 0061
Elin
0200, 0207, 0213,
0217
Elite
0209, 0213, 0218
Elman
0215
Elta
0200, 0208
Emerson
0060, 0061, 0062,
0064, 0128, 0205
Envision
0060, 0061
Erres
0213, 0217
ESA
0080
Etron
0208
Euro-Feel
0206
Euroline
0217
Euroman
0200
Euromann
0206, 0207, 0213
Europhon
0200, 0204, 0207,
0213, 0215
Fenner
0208
Ferguson
0212, 0217, 0226
Fidelity
0200, 0207, 0210
Finlandia
0210
Finlux
0204, 0205, 0207,
0213, 0215, 0217
Firstline
0200, 0207, 0208,
0213, 0214
Fisher
0064, 0127, 0128,
0205, 0207, 0215
Flint
0213, 0218
Formenti
0200, 0205, 0207,
0215, 0217
Formenti-Phoenix
0200
Fortress
0205
Frontech
0206, 0208, 0210,
0211, 0214
Fujitsu
0023, 0024, 0025,
0088, 0127
Funai
0033, 0034, 0035,
0036, 0037, 0062,
0206
Futuretech
0062
Gateway
0094
GBC
0208, 0215, 0218
GE
0057, 0060, 0061,
0122, 0147
GEC
0204, 0207, 0211,
0213, 0217
Geloso
0208, 0210, 0215
General Technic 0208
Genexxa
Gibralter
GoldHand
GoldStar
Goodmans
GPM
Graetz
Granada
Grandin
Grundig
Grunpy
Halifax
Hallmark
Hampton
Hanseatic
Hantarex
Harvard
HCM
Hifivox
Higashi
Hinari
Hisawa
Hitachi
Hornyphon
Hoshai
Huanyu
Hygashi
Hyper
Hypson
ICE
ICeS
IMA
Imperial
Indiana
Infinity
Ingelen
Ingersol
Inno Hit
Innovation
Interbuy
Interfunk
International
Intervision
Irradio
Isukai
ITC
ITS
0209, 0211, 0213,
0218
0060
0200
0060, 0061, 0127,
0128, 0200, 0201,
0207, 0208, 0210,
0213, 0214, 0215,
0217
0171, 0201, 0204,
0206, 0208, 0213,
0217, 0240
0209, 0218
0211
0204, 0207, 0210,
0213, 0217
0208, 0209, 0217
0128, 0130, 0222,
0236, 0255
0062
0200, 0206, 0207
0060, 0061
0200, 0207
0203, 0207, 0208,
0213, 0215, 0217
0204, 0208
0062
0206, 0207, 0208,
0218
0216
0200
0208, 0209, 0213,
0217, 0218
0209, 0218
0006, 0014, 0015,
0016, 0042, 0060,
0061, 0095, 0105,
0127, 0156, 0179,
0180, 0204, 0207,
0210, 0211, 0215,
0216, 0251
0213
0209, 0218
0200, 0207
0200, 0207
0200, 0207, 0208,
0214, 0215
0206, 0207, 0213,
0217
0127, 0200, 0206,
0207, 0208, 0209,
0213, 0218
0200, 0218
0062
0211, 0213, 0214,
0215
0213, 0217
0063
0211
0208
0201, 0204, 0207,
0208, 0209, 0213,
0217, 0218
0206, 0208
0208, 0214
0205, 0211, 0213,
0214, 0216, 0217
0200
0206, 0207, 0218
0201, 0208, 0209,
0213, 0217, 0218
0209, 0218
0207, 0215
0200, 0209, 0213,
0218
iv
APPENDIX
0093
0207
0208
0255
0206
0058, 0205, 0206,
0210, 0211
Adyson
0200, 0207
Agashi
0200
Agazi
0206
AGB
0204
Aiko
0127, 0200, 0207,
0208
Aiwa
0028, 0139, 0229,
0237
Akai
0059, 0065, 0127,
0129, 0130, 0200,
0204, 0208, 0209,
0213, 0217, 0218,
0255
Akiba
0209, 0218
Akura
0206, 0209, 0218
Alaron
0200
Alba
0200, 0207, 0208,
0209, 0217, 0218
ALBIRAL
0212
Allstar
0213
Amplivision
0207
Amstrad
0204, 0206, 0208,
0209, 0218
Amtron
0062
Anam
0208
Anam National 0062
Anglo
0208
Anitech
0206, 0208
Ansonic
0203, 0208
AOC
0060, 0061
Apex
0118, 0122, 0132
Arc en Ciel
0216
Arcam
0200
Arcam Delta
0207
Aristona
0213, 0217
ASA
0205, 0211
Asberg
0213
Astra
0208
Asuka
0200, 0206, 0207,
0209, 0218
Atlantic
0200, 0207, 0213,
0217
Atori
0208
Audiosonic
0207, 0208, 0209,
0213, 0216, 0217,
0218
AudioTon
0207
Audiovox
0062
Autovox
0205, 0206, 0207
Awa
0200
Baird
0216
Bang & Olufsen 0205
Basic Line
0208, 0209, 0213,
0218
Bastide
0207
Baur
0217
Beko
0228
Belcor
0060
Bell & Howell 0058, 0064
Benq
0081
Beon
0213, 0217
Bestar
0213
Binatone
0207
Black Star
0214
Blaupunkt
0255
Blue Sky
0209, 0218
Bondstec
0214
Boots
0207
Bradford
0062
Brandt
0216, 0226
Brionvega
0205, 0213, 0217
Britannia
0200, 0207
Brockwood
0060
Broksonic
0138
Bruns
0205
BSR
0215
BTC
0209, 0218
Bush
0177, 0208, 0209,
0210, 0213, 0215,
0216, 0217, 0218,
0230, 0237
Candle
0060, 0061
Capsonic
0206
Cascade
0208
Cathay
0213, 0217
CCE
0127
Celebrity
0059
Centurion
0213, 0217
Century
0205
CGE
0214, 0215
Cimline
0208, 0218
Citizen
0060, 0061, 0062,
0064
City
0208
Clarivox
0212, 0217
Clatronic
0206, 0207, 0208,
0209, 0213, 0214,
0218
CMS
0200
Colortyme
0060, 0061
Concerto
0060, 0061
Concorde
0208
Condor
0200, 0207, 0213
Contec
0200, 0207, 0208
Contec/Cony 0062
Continental Edison
0216
Cosmel
0208
Craig
0062
Crosley
0205, 0214, 0215
Crown
0062, 0063, 0128,
0208, 0213, 0217
CS Electronics 0200, 0207, 0209,
0214, 0218
CTC
0214
Curtis Mathes 0057, 0060, 0061,
0064, 0065
CXC
0062
Cybertron
0209, 0218
Daewoo
0060, 0061, 0120,
0127, 0155, 0193,
0200, 0207, 0208,
0213, 0218, 0238
Dainichi
0200, 0209, 0218
Dansai
0200, 0206, 0213,
0217
ITT
ITV
JBL
JC Penney
JCB
Jensen
JVC
0129, 0208, 0211
0208, 0217
0063
0057, 0060, 0061
0059
0060, 0061
0017, 0018, 0019,
0108, 0136, 0153,
0178, 0190, 0213,
0218
Kaisui
0200, 0207, 0208,
0209, 0218
Kamosonic
0207
Kamp
0200, 0207
Kapsch
0211
Karcher
0207, 0208, 0212,
0217
Kawasho
0059, 0060, 0061,
0200
Kendo
0128, 0210
Kennedy
0215
Kenwood
0060, 0061
Kingsley
0200, 0207
Kloss Novabeam
0062
Kneissel
0203
Kolster
0213
Konka
0209, 0218
Korpel
0213, 0217
Korting
0205
Koyoda
0208
KTV
0062, 0127, 0207
Kyoto
0200, 0212
Lenco
0208
Lenoir
0207, 0208
Lesa
0214
Leyco
0206, 0213, 0217
LG
0016, 0038, 0039,
0127, 0128, 0157,
0158, 0163, 0164,
0166, 0188, 0189,
0200, 0201, 0207,
0208, 0210, 0213,
0214, 0215, 0217
Liesenk
0217
Life
0206, 0208
Lifetec
0206, 0208, 0218
Loewe
0063, 0128, 0203,
0204, 0223, 0227
Loewe Opta
0205, 0213, 0217
Logik
0058
Luma
0210, 0217
Lumatron
0210, 0213, 0217
Lux May
0213
Luxman
0060, 0061
Luxor
0201, 0207, 0210
LXI
0057, 0061, 0063,
0064
Magnadyne
0204, 0205, 0214,
0215, 0217
Magnafon
0200, 0204, 0207
Magnavox
0060, 0061, 0063,
0102, 0103, 0150
Magnum
0206, 0208
Majestic
0058
Mandor
0206
Manesth
0206, 0207, 0213,
0217
Marantz
0060, 0061, 0063,
0090, 0213, 0217
Marelli
0205
Mark
0200, 0213, 0217
Matsui
0204, 0207, 0208,
0210, 0213, 0217
Mediator
0213, 0217
v
Medion
Megatron
Melectronic
0206, 0208
0061
0200, 0207, 0208,
0211, 0213, 0216,
0217
Memorex
0058, 0061, 0064,
0208
Memphis
0208
Metz
0205
MGA
0060, 0061
Micromaxx
0206, 0208
Microstar
0206, 0208
Minerva
0204
Minoka
0213
Mitsubishi
0006, 0015, 0016,
0048, 0060, 0061,
0104, 0112, 0113,
0125, 0205, 0213
Mivar
0200, 0201, 0202,
0203, 0204, 0207
Montgomery Ward
0058
MTC
0060, 0061, 0128,
0200
Multi System 0217
Multitech
0062, 0127, 0128,
0200, 0207, 0208,
0210, 0214, 0215,
0217
Murphy
0200, 0207
NAD
0061
Naonis
0210
NEC
0026, 0053, 0060,
0061, 0096, 0127
Neckermann
0205, 0207, 0210,
0213, 0217, 0255
NEI
0213, 0217
Nesco
0214
NET-TV
0082, 0101
New Tech
0208, 0213
New World
0209, 0218
Nicamagic
0200, 0207
Nikkai
0200, 0206, 0207,
0209, 0213, 0217,
0218
Nikko
0061
Nobliko
0200, 0207
Nogamatic
0216
Nokia
0129, 0211
Nordmende
0205, 0211, 0213,
0216
Nordvision
0217
Oceanic
0211
Olevia
0084
ONCEAS
0207
Onwa
0062, 0218
Orbit
0213
Orion
0126, 0204, 0208,
0213, 0217, 0235
Orline
0218
Orsowe
0204
Osaki
0127, 0206, 0207,
0209, 0218
Osio
0201
Oso
0209, 0218
Osume
0218
Otto Versand 0204, 0207, 0213,
0215, 0216, 0217,
0255
Pael
0200, 0207
Palladium
0207
Panama
0200, 0206, 0207,
0208
Panasonic
0006, 0007, 0063,
0073, 0074, 0097,
0110, 0114, 0137,
0141, 0151, 0162,
0165, 0186, 0204,
0211, 0244, 0245,
0246, 0254
Pathe Cinema 0200, 0203, 0207,
0212, 0215
Pathe Marconi 0212, 0216
Pausa
0208
Perdio
0200
Philco
0060, 0061, 0063,
0128, 0205, 0214,
0215
Philharmonic 0207
Philips
0040, 0060, 0063,
0072, 0115, 0116,
0124, 0130, 0150,
0175, 0184, 0187,
0205, 0207, 0213,
0215, 0217, 0220,
0221, 0232, 0233,
0252, 0253
Philips Magnavox
0124
Phoenix
0200, 0205, 0213,
0217
Phonola
0200, 0205, 0213,
0217
Pilot
0060
Pioneer
0012, 0013, 0060,
0061, 0098, 0109,
0117, 0128, 0181,
0182, 0194, 0195,
0211, 0213, 0216,
0217, 0250
Plantron
0206, 0213
Polaroid
0075
Poppy
0208
Portland
0060, 0061
Prandoni-Prince 0204, 0210
Precision
0207
Prima
0208, 0211
Profex
0208
Profi-Tronic
0213
Proline
0213
Proscan
0057
Prosonic
0200, 0207, 0217
Protech
0206, 0207, 0208,
0213, 0214, 0215,
0217
Proton
0060, 0061
Provision
0217
Pulsar
0060
Pye
0213, 0217
Pymi
0208
Quasar
0152, 0214
Quelle
0201, 0206, 0207,
0213, 0214, 0215,
0217
Radialva
0218
Radio Shack
0064
Radio Shack/Realistic
0057, 0060, 0061,
0062, 0064
Radiola
0213, 0217
Radiomarelli
0204, 0205, 0214
Radiotone
0213
RCA
0057, 0060, 0061,
0091, 0133, 0135,
0147, 0149
Realistic
0064
Revox
0213, 0217
Rex
0206, 0210, 0211
RFT
Rhapsody
R-Line
Roadstar
0203, 0205
0200
0213, 0217
0206, 0208, 0209,
0218, 0237
Robotron
0205
Rowa
0200
RTF
0205
Saba
0204, 0205, 0211,
0216
saccs
0212
Saisho
0204, 0206, 0207,
0208
Salora
0201, 0204, 0210,
0211, 0215
Sambers
0204
Sampo
0060, 0061, 0083,
0101
Samsung
0029, 0030, 0031,
0032, 0044, 0045,
0046, 0047, 0060,
0061, 0065, 0068,
0069, 0071, 0079,
0087, 0127, 0128,
0130, 0144, 0160,
0161, 0170, 0176,
0183, 0185, 0200,
0201, 0206, 0207,
0208, 0213, 0217,
0239, 0241, 0242,
0243
Sandra
0200, 0207
Sansui
0123, 0126, 0213
Sanyo
0020, 0021, 0022,
0049, 0060, 0064,
0127, 0128, 0200,
0203, 0207, 0215
SBR
0217
SCHAUB LORENTZ
0211
Schneider
0207, 0209, 0213,
0215, 0216, 0217,
0218
Scotch
0061
Scott
0060, 0061, 0062
Sears
0057, 0060, 0061,
0064
SEG
0200, 0206, 0207,
0214, 0215, 0217
SEI
0204
SEI-Sinudyne 0204, 0205, 0211
Seleco
0210, 0211, 0215
Sencora
0208
Sentra
0218
Serino
0200
Sharp
0009, 0010, 0011,
0060, 0061, 0066,
0070, 0087, 0111,
0143, 0145, 0167,
0168, 0169, 0198,
0204, 0224, 0247,
0248, 0249
Shogun
0060
Siarem
0204, 0205, 0215
Sicatel
0212
Siemens
0255
Sierra
0213
Signature
0058
Silva
0200
Singer
0205, 0214, 0215
Sinudyne
0204, 0205, 0215,
0217
Skantic
0211
Solavox
0211
Sonoko
Uher
Ultravox
0211, 0213
0200, 0205, 0207,
0214, 0215
United
0217
Universum
0127, 0128, 0129,
0201, 0206, 0213,
0214, 0215, 0217
Univox
0212
Vestel
0210, 0211, 0213,
0214, 0215, 0217
Vexa
0208, 0217
Victor
0213
VIDEOLOGIC 0200
Videologique 0200, 0207, 0209,
0218
Videosat
0214
VideoSystem 0213
Videotechnic 0200
Vidtech
0060, 0061
Viewsonic
0076, 0077, 0092,
0099, 0172, 0173
Visiola
0200, 0207
Vision
0213
Vortec
0213, 0217
Voxson
0205, 0210, 0211,
0213
Waltham
0207, 0212
Wards
0057, 0058, 0060,
0061, 0063
Watson
0213, 0217, 0218
Watt Radio
0200, 0207, 0212,
0215
Wega
0205
Weltblick
0213, 0217
Weston
0215
White Westinghouse
0200, 0207, 0217
Yamaha
0000, 0001, 0002,
0003, 0004, 0005,
0060, 0061
Yamishi
0218
Yoko
0200, 0206, 0207,
0208, 0209, 0213,
0217, 0218
Yorx
0209, 0218
Zanussi
0210
Zenith
0058, 0060, 0100,
0105, 0119, 0121,
0154
TV/DVD
Aiwa
Apex
Broksonic
Bush
JVC
Panasonic
RCA
Sylvania
Thomson
Toshiba
0139, 2055
0132, 2049
0138, 2060
0230, 2112
0136, 2053
0137, 0254, 2054,
2110
0133, 0135, 2050,
2051
0134, 2052
0226, 2109
0131, 0231, 2048,
2111
TV/DVD/VCR
Panasonic
Samsung
Sharp
Sylvania
Toshiba
0141, 1040, 2057
0241, 1070, 2113
0143, 1028, 2059
0142, 1041, 2058
0140, 1029, 2056
TV/VCR
Aiwa
Bush
0237, 1066
0237, 1066
Daewoo
GE
Goodmans
Grundig
Hitachi
JVC
Magnavox
Orion
Panasonic
Philips
Quasar
RCA
Roadstar
Samsung
Sharp
Sony
Sylvania
Tatung
Toshiba
Zenith
0155, 0238, 1038,
1067
0147, 1030
0240, 1069
0236, 1062
0156, 1039
0153, 1036
0150, 1033
0235, 1065
0151, 1034
0150, 0232, 0233,
1033, 1062, 1063
0152, 1035
0149, 1032
0237, 1066
0144, 0239, 1027,
1068
0145, 1028
0234, 1064
0148, 1031
0237, 1066
0146, 0237, 1029,
1066
0154, 1037
VCR
Admiral
Adventura
Aiwa
1008, 1013
1005
1005, 1042, 1043,
1044, 1066
Akai
1007, 1043
Akiba
1050
Akura
1043, 1050
Alba
1044, 1050
American High 1004
Amstrad
1042
Anitech
1050
ASA
1045, 1046
Asha
1002, 1014
Asuka
1042, 1045, 1046,
1050
Audio Dynamics1000
Audiovox
1003
Baird
1042, 1043, 1047
Basic Line
1044, 1050
Baur
1046
Beaumark
1002, 1014
Bell & Howell 1001
Blaupunkt
1046, 1048
Broksonic
1012, 1013
Bush
1044, 1050, 1066
Calix
1003
Candle
1002, 1003
Canon
1004
CCE
1006
CGE
1042, 1043
Cimline
1044, 1050
Citizen
1002, 1003
Colortyme
1000
Colt
1006
Craig
1002, 1003, 1006,
1014
Crown
1050
Curtis Mathes 1000, 1002, 1004,
1009
Cybernex
1002, 1014
Daewoo
1005, 1038, 1061,
1067
Dansai
1050
Dantax
1044
DBX
1000
De Graaf
1046, 1049
Decca
1042, 1043, 1046
Denon
1010
Dimensia
1009
Dual
Dumont
1043, 1046
1042, 1046, 1047,
1049
Dynatech
1005
Electrohome
1003
Electrophonic 1003
Elta
1050
Emerson
1003, 1004, 1005,
1012, 1013
Etzuko
1050
Ferguson
1043
Fidelity
1042
Finlandia
1046, 1047, 1049
Finlux
1042, 1043, 1046,
1047, 1049
FIRST LINE 1044, 1045, 1049,
1050
Fisher
1001, 1047
Flint
1044
Formenti/Phoenix
1046
Fuji
1004
Fujitsu
1042
Funai
1005, 1042
Galaxy
1042
Garrard
1005
GBC
1050
GE
1002, 1004, 1009,
1014, 1030
GEC
1046
Geloso
1050
General Technic 1044, 1048
Go Video
1014
GoldHand
1050
Goldstar
1000, 1003, 1042,
1045
Goodmans
1042, 1045, 1050,
1069
Gradiente
1005
Graetz
1043, 1047
Granada
1046, 1047, 1049
Grandin
1042, 1045, 1050
Grundig
1046, 1050, 1062
Hanseatic
1045, 1046
Harley Davidson1005
Harman/Kardon 1000
Harwood
1006
HCM
1050
Headquarter
1001
Hinari
1044, 1050
Hisawa
1044
Hitachi
1007, 1010, 1039,
1042, 1043, 1046,
1049
Hughes Network Systems
1010
Hypson
1044, 1050
Imperial
1042
Inno Hit
1046, 1050
Innovation
1044, 1048
Instant Replay 1004
Interbuy
1045
Interfunk
1046, 1047
Intervision
1042
Irradio
1045, 1050
ITT
1043, 1047
ITV
1045
JC Penney
1000, 1001, 1002,
1003, 1004, 1006
JCL
1004
Jensen
1007
JVC
1000, 1001, 1007,
1011, 1017, 1036,
1043
Kaisui
1050
vi
APPENDIX
0206, 0207, 0208,
0213, 0217
Sonolor
0211
Sontec
0213, 0217
Sony
0041, 0059, 0067,
0085, 0086, 0174,
0196, 0199, 0208,
0219, 0234
Sound & Vision 0209, 0218
Soundesign
0060, 0061, 0062
Soundwave
0213, 0217
SSS
0060, 0062
Standard
0207, 0208, 0209,
0213, 0218
Starlight
0217
Starlite
0062
Stenway
0218
Stern
0210, 0211
Sunkai
0208, 0218
Sunwood
0208, 0213
Superla
0200, 0204, 0207
SuperTech
0200
Supra
0208
Supreme
0059
Susumu
0209
Sutron
0208
Sydney
0200, 0207
Sylvania
0060, 0061, 0063,
0080, 0134, 0142,
0148
Symphonic
0062, 0080
Sysline
0217
Sytong
0200
Tandy
0127, 0207, 0209,
0211, 0218
Tashiko
0200, 0207, 0210
Tatung
0127, 0204, 0207,
0213, 0217, 0237
TCM
0206, 0208
Teac
0127
Tec
0207, 0208, 0214,
0215
Techwood
0060, 0061
Teknika
0058, 0060, 0061,
0062
Teleavia
0216
Telecor
0218
Telefunken
0065, 0213, 0216
Telegazi
0218
Teletech
0208, 0214, 0217
Teleton
0207
Televideon
0200
Tensai
0208, 0209, 0213,
0218
Tesmet
0213
Tevion
0206, 0208
Texet
0200, 0207
Thomson
0191, 0192, 0207,
0213, 0216, 0226
Thorn
0212, 0217
TMK
0060, 0061
Tokai
0213
Tokyo
0200, 0207
Toshiba
0027, 0043, 0053,
0054, 0064, 0078,
0089, 0090, 0106,
0107, 0127, 0131,
0140, 0146, 0159,
0197, 0225, 0231,
0237
Towada
0211, 0215
Transtec
0200
Trident
0204
Tristar
0218
Triumph
0204
RX-V463_G-cv.fm Page 1 Friday, January 11, 2008 10:21 AM
G
Karcher
Kendo
Kenwood
National
NEC
1048
1000, 1001, 1007,
1011, 1043, 1051
Neckermann
1043, 1046
NEI
1046
Nesco
1050
Nikko
1003
Noblex
1002, 1014
Nokia
1043, 1047
Nordmende
1043
Oceanic
1042, 1043
Okano
1044
Olympus
1004
Optimus
1003, 1008
Orion
1012, 1013, 1044,
1065
Orson
1042
Osaki
1042, 1045, 1050
Otto Versand 1046
Palladium
1043, 1045, 1050
Panasonic
1004, 1020, 1034,
1040, 1048, 1054,
1072
Pathe Marconi 1043
Penney
1010, 1014
Pentax
1010, 1049
Perdio
1042
Philco
1004, 1051
Philips
1004, 1025, 1033,
1046, 1056, 1057,
1059, 1062, 1063
Philips Magnavox
1018
Phonola
1046
Pilot
1003
Pioneer
1011, 1046
Prinz
1042
Profex
1050
Profitronic
1014
Proline
1042
Proscan
1009
Prosonic
1044
Protec
1006
Pye
1046, 1056
Quarter
1001
Quartz
1001, 1047
Quasar
1004, 1035
Quelle
1042, 1046, 1047
Radio Shack
1003
Radio Shack/Realistic
1001, 1002, 1003,
1004, 1005, 1008
Radiola
1046
Radix
1003
Randex
1003
RCA
1002, 1004, 1009,
1010, 1014, 1015,
1022, 1032
Realistic
1001, 1002, 1003,
1004, 1005, 1008
Rex
1043
RFT
1046
Roadstar
1045, 1050, 1066
Saba
1043
Saisho
1044, 1050
Salora
1047
Samsung
1002, 1014, 1021,
1027, 1052, 1068,
1070
Sanky
1008
Sansui
1007, 1011, 1013,
1043
Sanyo
1001, 1002, 1014,
1047
SBR
1046
Schaub Lorenz 1042, 1043, 1047
Schneider
1042, 1044, 1045,
1046, 1050
Scott
1012
Sears
1001, 1003, 1004,
1010
SEG
1050
SEI-Sinudyne 1046
Seleco
1043
Sentron
1050
Sharp
1008, 1023, 1028,
1053, 1073
Shintom
1006, 1047, 1050
Shivaki
1045
Shogun
1002, 1014
Siemens
1045, 1047
Signature 2000 1008
Silva
1045
Singer
1004, 1006
Sinudyne
1046
Sontec
1045
Sony
1016, 1019, 1055,
1060, 1064, 1074
STS
1004, 1010
Sunkai
1044
© 2008
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY. LTD. LEVEL 1, 99 QUEENSBRIDGE STREET, SOUTHBANK, VIC 3006, AUSTRALIA
Black process 45.0° 240.0 LPI
Sunstar
Suntronic
Sunwood
Sylvania
1042
1042
1050
1004, 1005, 1031,
1041
Symphonic
1005
Taisho
1044
Tandy
1001
Tashiko
1003, 1042
Tatung
1007, 1042, 1043,
1046, 1066
TCM
1044, 1048
Teac
1005, 1007
Technics
1004, 1048
Teknika
1003, 1004, 1005
Teleavia
1043
Telefunken
1043
Tenosal
1050
Tensai
1042, 1045, 1050
Tevion
1044, 1048
Thomson
1043, 1058
Thorn
1043, 1047
TMK
1002, 1014
Tokai
1045, 1050
Tonsai
1050
Toshiba
1013, 1024, 1029,
1043, 1046, 1066,
1075
Totevision
1002, 1003, 1014
Towada
1050
Towika
1050
Uher
1045
Unitech
1002, 1014
Universum
1042, 1045, 1046
Vector Research 1000
Video Concepts 1000
Videon
1044, 1048
Videosonic
1002, 1014
Wards
1002, 1003, 1004,
1005, 1006, 1008,
1010, 1014
Weltblick
1045
White Westinghouse
1013
XR-1000
1004, 1005, 1006
Yamaha
1000, 1001, 1007
Yamishi
1050
Yokan
1050
Yoko
1045, 1050
Zenith
1013, 1026, 1037
All rights reserved.
Printed in China
WN25730
RX-V463
1046
1044
1000, 1001, 1007,
1011, 1043
KLH
1006
Kodak
1003, 1004
Korpel
1050
Leyco
1050
LG
1003, 1042, 1045,
1071
Lifetec
1044, 1048
Lloyd's
1005
Loewe
1048
Loewe Opta
1045, 1046
Logik
1006, 1050
Luxor
1047
LXI
1003
M Electronic 1042
Magnasonic
1047
Magnavox
1004, 1018, 1033
Magnin
1003, 1014
Manesth
1050
Marantz
1000, 1001, 1004,
1046, 1051
Marta
1003
Matsui
1044, 1045
Matsushita
1004
Mediator
1046
Medion
1044, 1048
MEI
1004
Memorex
1001, 1002, 1003,
1004, 1005, 1008,
1013, 1014, 1042,
1045, 1047
Memphis
1050
Metz
1048
MGA
1014
MGN Technology
1002, 1014
Micromaxx
1044, 1048
Microstar
1044, 1048
Migros
1042
Minolta
1010
Mitsubishi
1011, 1042, 1046
Montgomery Ward
1008
Motorola
1004, 1008
MTC
1002, 1014
Multitech
1002, 1005, 1006,
1042, 1046, 1050
Murphy
1042
RX-V463
AV Receiver
Ampli-tuner audio-vidéo
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
GEBRUIKSAANWIJZING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
00_Sheet_RX-V463_EX.book Page 1 Monday, January 7, 2008 5:26 PM
RTKAGLEF
RX-V463
The circled numbers and alphabets correspond to those in the Owner’s Manual.
Les nombres et lettres dans un cercle correspondent à ceux du mode d’emploi.
Die umkreisten Zahlen und Buchstaben entsprechen denen in der Bedienungsanleitung.
Inringade nummer och bokstäver motsvarar de som anges i bruksanvisningen.
I manuali e le lettere dell’alfabeto corrispondono a quelli nel Manuale di istruzioni.
Los números y las letras en el interior de círculos se corresponden con aquellos del manual de instrucciones.
De omcirkelde cijfers en letters corresponderen met die in de Gebruiksaanwijzing.
Цифры и буквы в кружках относятся к цифрам и буквам в Инструкции по эксплуатации.
带圆圈的数字和文字与说明书中的同类数字和文字相对应。
원 번호 및 원 알파벳은 사용 설명서 안의 표기와 일치합니다 .
■ Front panel/Face avant/Frontblende/Frontpanelen/Pannello anteriore/Panel delantero/Voorpaneel/
Фронтальная панель/ 前部面板 / 전변 패널
A
B
C
D
E
F
GH
I
VOLUME
STANDBY
/ON
OPTIMIZER MIC
EDIT
PRESET/TUNING
BAND
l PRESET/TUNING/CH h
A/B/C/D/E
MEMORY
TUNING AUTO/MAN'L
SCENE
1
l
PHONES
SPEAKERS
A/B/OFF
PROGRAM
TONE CONTROL
3
STRAIGHT
DIRECT
h
4
l
INPUT
VIDEO AUX
h
VIDEO
AUDIO SELECT
EFFECT
SILENT CINEMA
J
Black process 45.0° 240.0 LPI
2
K
L
M
N
O
P
Q
L
AUDIO
USB
R
00_Sheet_RX-V463_EX.book Page i Monday, January 7, 2008 5:26 PM
■ Remote control/Boîtier de télécommande/Fernbedienung/Fjärrkontrollen/
Telecomando/Mando a distancia/Afstandsbediening/Пульт ДУ/ 遥控器 /
리모콘
1
2
3
POWER
POWER
TV
AV
USB
STANDBY
POWER
A
B
MUTE
CD
MD/CD-R
TUNER
DVD
DTV/CBL
DVR
V-AUX/DOCK
C
D
AMP
TV INPUT
TV MUTE
1
2
G
H
I
TV CH
J
TV VOL
4
SCENE
5
6
BAND LEVEL
TITLE
7
8
3
4
VOLUME
MENU
L
ENTER
DISPLAY
RETURN
MEMORY
K
M
REC
9
0
A
B
C
D
E
F
FREQ/TEXT
l
EON
PROG h
MODE - PTY SEEK - START
ENHANCER SUR. DECODE
1
2
3
4
STRAIGHT
DIRECT
NIGHT
PARAMETER
5
6
7
MULTI CH IN AUDIO SEL
9
0
10
8
SLEEP
ENT
N
O
P
Q
R
Printed in China
Black process 45.0° 240.0 LPI
WN26200