SHR-3040
4 Channel DVR
User’s Manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please
register your product at
www.samsungsecurity.com
00000A_SHR-3040_ENG.indb 1
2009-06-10 오후 3:38:03
overview
Key Features
Display
~ Real Time Display of Each Channel
~ Auto Sequence display of 4 channels
~ PIP (Picture in Picture)
~ Pause Mode
~ 2X ZOOM
~ Quick Switch between Live and Playback Screen
~ PTZ Camera supported
Record
~ Up to 3 Levels of Quality and Frame Rates
~ Audio Recording
~ Scheduled Recording
~ Event Recording using External Sensors and Motion Detection
~ Emergency Recording
Network
~ Remote Monitoring using Web Viewer
~ Supports DDNS Service
Play
~ Search by the Data Size, and Date/Time
~ Play Speed Adjustment and Forward/Backward Playback
~ Event Search
Data Storage
~ Simple, Easy Backup using USB Memory
~ Network Backup
Others
~ UNI-CODE supported
~ Spot Monitor
~ Video Loss Detection
_ overview
00000A_SHR-3040_ENG.indb 2
2009-06-10 오후 3:38:03
Important Safety Instructions
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
! overview
2)
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Standards Approvals
M
` This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
English _
00000A_SHR-3040_ENG.indb 3
2009-06-10 오후 3:38:04
overview
BEFORE START
This user’s manual provides Information for using DVR such as brief introduction, part names, functions, connection
to other equipment, menu setup, and the like.
You have to keep in mind the following notices:
~ SEC retains the copyright on this manual.
~ This manual cannot be copied without SEC ’s prior written approval.
~ We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of
instructions mentioned in this manual.
~ If you want to open the case of your system for checking problems, please consult the expert from the shop
where you bought the product.
~ Before installing or replacing the HDD, or connecting a USB memory device to the DVR, check if it is compliant
with the DVR. For the compatibility, contact the retailer where you purchased the product.
Warning
❖ Battery
Exchanging a wrong battery in your product may cause an explosion. Therefore you must use the same type
of battery as the one being used in the product.
The following are the specifications of the battery you are using now.
~ Normal voltage: 3V
~ Normal capacity: 220mAh
~ Continuous standard load: 0.2mA
~ Operating temperature: -20°C ~ +85°C (-4°F ~ +185°F)
J
` Connect the power cord into a grounded outlet.
` The Mains plug is used as a disconnect device and shall stay readily operable at any time.
` Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
❖ System Shutdown
Turning off the power while the product is in operation, or taking not permitted actions may cause damage to
the hard drive or the product. Also it can cause a dysfunction to the hard disk while using the product.
For safe power disconnection, select <SHUTDOWN> in the DVR menu and remove the power cable.
You may want to install a UPS system for safe operation in order to prevent damage caused by an
unexpected power stoppage.
(Any questions concerning UPS, consult your UPS retailer.)
❖ Operating Temperature
The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).
This product may not work properly if you run right after a long period of storage at a temperature below the
guaranteed one.
When using the device after a long period of storage at low temperature, place the product at room
temperature for a while and run it.
Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).
Likewise, the hard drive may not work at a temperature below the guaranteed one.
_ overview
00000A_SHR-3040_ENG.indb 4
2009-06-10 오후 3:38:04
What’s Included
Unpack the product package and put down the product on a flat floor or in an installation place.
Check if all components of the package are included.
SHR-3040
! overview
DVR
Remote Control/Battery (AAAX2)
Mouse
Installation CD
User’s Manual
AC Adaptor/Power Cable
English _
00000A_SHR-3040_ENG.indb 5
2009-06-10 오후 3:38:07
overview
Contents
overview
2
3
4
6
8
9
10
Key Features
Important Safety Instructions
Before Start
Contents
Front Panel
Rear Panel
Remote Control at a Glance
Installation
11
12
13
14
14
Checking the Installation Environment
Installing HDD
Connecting to a Different Device
Network Connection
USB Connection
live
15
18
18
19
19
19
20
20
21
22
23
24
Live
Mode Switch
PIP Display
Zoom
Auto Sequence
Freeze
Record
PTZ
Search
Play
Event Monitoring
Event Monitoring on the Spot Monitor
setup
25
26
28
30
36
42
44
45
46
47
Using the Menu
Display Setup
Record
Configuration
External Device
Backup
Firmware Upgrade
Factory Default
Language
Network Connection and Settings
2
11
15
25
_ overview
00000A_SHR-3040_ENG.indb 6
2009-06-10 오후 3:38:07
web viewer
51
63
What is Web Viewer?
Connecting to the Web Viewer
Web Viewer at a Glance
Client Setup
Remote Setup
Backup
Player
Remote Viewer
Search
! overview
appendix
51
51
52
53
54
56
56
59
62
63 Product Specification
65 Appearance & Dimension
66 Troubleshooting (FAQ)
English _
00000A_SHR-3040_ENG.indb 7
2009-06-10 오후 3:38:08
overview
Front Panel
1
2
3
4
Item
USB Port
LED
Play
5
6 7
8
Description
Used to connect a USB memory device.
Power
Displays the status of the system power.
HDD
Blinks when a hard disk is accessed.
(
Plays video backward.
! REC
Starts or ends recording.
)
Plays video forward.
+
Plays a recorded channel forward.
#
Stops playing a video.
_
Plays a video backward.
MODE
Switches to a split mode.
+/-
Allows you to change the menu settings or control Zoom In/Out in PTZ mode.
MENU
Accesses the menu screen.
Moves one level up from the menu screen.
RETURN
This will operate as Stop button during playback.
4/PTZ
Moves to channel 4. Press and hold this button to enter PTZ mode.
3/PIP
Moves to channel 3. Press and hold this button to enter PIP mode.
2/SEQ
Moves to channel 2. Press and hold this button to enter SEQ mode.
1/ZOOM
Moves to channel 1. Press and hold this button to enlarge the image; press it again to
return to the previous size.
Direction Buttons
($%_ +)
Use the direction buttons to navigate through the menu items.
OK(
Selects and runs a menu item.
)
_ overview
00000A_SHR-3040_ENG.indb 8
2009-06-10 오후 3:38:08
Rear Panel
1
2 3
4
Item
6 7
! overview
9
5
8
Description
AUDIO IN
Audio signal input port. (RCA jack)
AUDIO OUT
Audio signal output port. (RCA jack)
RS-485
Connector for an RS-485-based external device. (Pan/Tilt/Zoom)
ALARM Output
Alarm output port.
SENSOR Input
Sensor input terminal.
VGA
Video output port to a VGA monitor.
VIDEO IN (CH 1~4)
BNC port for camera video input. (up to 4 cameras supported)
VIDEO OUT
BNC port for AV monitor output.
PS/2
PS/2 type mouse connection port.
DC Input
Power connection port for a 12V/4A adaptor.
SPOT OUT
Output (COMPOSITE) port for a NTSC- or PAL-based spot monitor.
NETWORK
RJ-45 port for network connection.
English _
00000A_SHR-3040_ENG.indb 9
2009-06-10 오후 3:38:09
overview
Remote Control At a Glance
SEARCH
The Search menu appears.
PTZ
The PTZ control menu appears.
Menu
Opens the main menu, or moves to the
previous stage.
Number
Use this pad to enter a number or display a
single screen.
FUNC
The Launcher menu appears.
REC
Starts/stops recording.
MODE
Switches to a split mode.
AUDIO
Turns on or off the sound.
CH +/Moves the channel up or down.
Direction/OK
Used to move the cursor up/down or left/
right./Used to select and run a menu item.
+/Used to change the menu settings or
control Zoom In/Out.
Play
Play
Pause Backward, Backward Play, Play,
Pause Forward
Fast Backward, Pause, Stop, Fast Forward
ZOOM
SEQ
Enlarges the screen (2x) digitally.
Switches to auto sequence mode.
FRZ
Freezes the screen temporarily.
PIP
Displays the PIP screen.
10_ overview
00000A_SHR-3040_ENG.indb 10
2009-06-10 오후 3:38:09
installation
Please be noticed with the followings before you use the product.
Do not use the product outdoor.
Do not spill water or liquid in the connection part of the product.
Do not impose the system to excessive shock or force.
Do not pull out the power plug forcefully.
Do not disassemble the product on your own.
Do not exceed the rated input/output range.
Use a certified power cord only.
For the product with an input ground, use a grounded power plug.
! iNstallatiON
~
~
~
~
~
~
~
~
cHecKiNG tHe iNstallatiON eNvirONmeNt
~ Samsung Digital video recorder (“DVR” hereinafter) is a stateof-art security device, and contains mass storage hard disk(s)
and critical circuits inside.
Temperature
Unit: ºC
One Year: 24HR X 365 DAY =8,760 HR
~ When the temperature rises inside the product, the product
may breakdown and the product life be shortened. please
pay attention to the following recommendations before
installation.
Life (Unit: HOURS)
[Figure 1]
The followings are the recommendations when Samsung DVR is installed on a
rack.
1. Please ensure that the rack inside is not sealed.
2. Please ensure the air is circulated through the inlet/outlet as shown in the
picture.
3. If the DVR or other devices on a rack is to be stacked as in the picture,
provide a suitable space or install a ventilating opening for air circulation.
4. For natural air convection, place the inlet at the bottom of the rack and the
outlet on top.
5. It is strongly recommended that a fan motor is installed at the inlet and the
outlet for air circulation. (Please fit a filter at the inlet to screen dust or foreign
substances.)
6. Please maintain the temperature inside the rack or surrounding areas
between 0°C ~ 40°C (32°F ~ 104°F) as shown in the fgure 1.
J
` The rack installation is available only in shelf type.
[Figure 2]
English _11
00000A_SHR-3040_ENG.indb 11
2009-06-10 오후 3:38:21
installation
Installing HDD
You can install a separate HDD if your recorder has no built-in HDD.
MAIN BOARD
HDD
SATA
1. Loosen the screws in the left and right sides and remove the cover.
. Use the SATA data cable to connect the main board with the HDD, and connect the HDD power cable.
. Attach the HDD cushion to the internal bottom of the DVR, place the HDD over it, and use the provided screws
to fix the HDD.
M
` If the HDD is not installed properly, it may not work at all. So it is necessary to contact the retailer for the replacement
J
` Data Loss Precautions (HDD Maintenance)
process.
~ The screw should be fixed from outside the case, and do not put excessive force on it.
Take good care not to damage the HDD.
If you replace the HDD, make sure to check if it's compliant with the DVR.
As the HDD is sensitive to an external impact that may cause malfunction, please take caution not to impact on it.
If the HDD is damaged from your carelessness or an external impact, Samsung shall not be responsible for any damage
to it.
` If the HDD and its data can be damaged in the following cases:
To minimize a risk of damage to the HDD, make a regular backup of your data in it.
Data can be damaged if an external impact is put on the DVR while removing or installing the DVR.
If the DVR is stopped from a power failure or by your turning it off while the HDD is working, the HDD can be damaged.
If you move or impact on the DVR while it is working, the HDD can be damaged.
12_ installation
00000A_SHR-3040_ENG.indb 12
2009-06-10 오후 3:38:23
Connecting to a different device
Connecting to video, audio, and monitor
CAMERA
! Installation
MONITOR
VGA
MONITOR
MOUSE
MIC
SPEAKER
SPOT MONITOR
Connecting to RS-485, alarm, sensor
Connecting RS-485 device
Connection port used to control an external device such as the
PTZ and speed dome camera.
Connect the external device to the RS-485 port (PIN 1:-, 2:+) in
the rear [FUNCTION] panel.
M
` Check if the RS-485 device is compliant with the DVR.
` Please take care about the polarity (+/-) of RS-485 when
installing it.
` The polarity may differ, depending on the camera model.
` For more information, refer to the user guide of the PTZ
camera.
Connecting alarm output
Connection port used to sound the alarm.
~ PIN 3: RELAY COM / 4: RELAY NC / 5: RELAY NO
Connect one strand of the signal cable (two strands) to the [COM]
port and connect the other strand to a desired alarm output port.
Connecting Alarm Input
RS-485
ALARM OUT
ALARM IN
Connection port used to receive the sensor signal.
~ PIN 6: ALARM GND, 7: ALARM 4, 8: ALARM 3, 9: ALARM 2, 10: ALARM 1
Connect one strand of the sensor signal cable (two strands) to the [GND] port and connect the other strand
to a desired alarm input port.
English _13
00000A_SHR-3040_ENG.indb 13
2009-06-10 오후 3:38:24
installation
NetwOrK cONNectiON
You can use the Ethernet connector to connect to the network.
Connecting to the network consisting of multiple computers enables you to perform various functions including
remote monitoring, remote search, and remote control.
Cable/ADSL/VDSL
IP Router
Internet
or
DDNS Server
(websamsung.net)
Direct LAN (Dynamic/Static IP)
SHR-3040
Local PC #1
CAMERA
Remote User PC #1
Local PC #N
Remote User PC #N
SHR-3040
Data Line :
Video Line :
usB cONNectiON
The DVR has one USB port on the front panel.
You can connect the USB memory to the USB port for data backup or firmware upgrade.
Format the USB device in the FAT32 file system, on your PC if not formatted on the DVR.
1_ installation
00000A_SHR-3040_ENG.indb 14
2009-06-10 오후 3:38:26
live
live
Getting started
2009/05/01
00:00:01
14D
00:00:01
14D
! live
1. Connect the power cable of the DVR to the wall outlet.
When it turns on, the system gets started automatically.
login
To access a DVR or restricted menu, you should have logged in to the DVR.
1. In Live Screen, right-click any area of the screen.
The Control icon appears in the bottom.
2009/05/01
. Click the menu icon [
].
` You can also see the login dialog by pressing the [MENU] button
on the remote control.
. Use the cursor to enter the password, or press a
combination of numbers on the remote control.
M
` Default ID: ADMIN
` Default Password: 4321
. Select <eNter>.
You will access the main menu.
DVR LOG-IN
USER ID
ADMIN
USER PW
0
1
-------2
3
4
5
6
ENTER
7
8
9
EXIT
English _1
00000A_SHR-3040_ENG.indb 15
2009-06-10 오후 3:38:29
live
live screen configuration
You can check the status or operation of the DVR with the icons on the live screen.
1
2009/05/01
00:00:01
14D
10
Item
Description
Current Date, Time
Displays the current time and date.
Live Screen
Status
Displays the audio output status.
Displays the status of PTZ, PIP, ZOOM, SEQ, and FRZ, respectively.
Network
Connection
Status
Displays the network connection status in network connection or
disconnection.
Record
Status
Displays the recording status.
Overwrite
Displays the overwrite status of the HDD.
Displays the number of days to record.
HDD
Camera Name
Event
14D
In the figure above, you will have 14 more days to store recording
data.
AUTO
Displays if you set to use auto deletion.
FULL
Displays if you choose not to use overwriting and the HDD is full.
OW
Displays if you set to use overwriting.
Displays the name of the current camera.
Displays if a motion is detected.
Displays if an alarm sounds.
Channel
Selection
You can switch to channel 1, 2, 3, 4 or a split mode.
Launcher
Menu
You can access menus of Record, Setup, PTZ, PIP, ZOOM, SEQ,
FRZ and Play.
1_ live
00000A_SHR-3040_ENG.indb 16
2009-06-10 오후 3:38:34
view the launcher menu
You can use the Launcher menu appearing on the bottom of the live screen to access it.
1. In Live mode, right-click any area or press the [FuNc]
button on the remote control.
The Launcher menu appears in the bottom.
2009/05/01
00:00:01
14D
. Move the cursor over the bottom, and click a desired item
in the Launcher menu to access it.
! live
Menu
Description
Mode Switch
Switches to a single or split mode for each channel.
Record
Performs the manual recording.
Main Menu
Log into the main screen.
PTZ
The PTZ control icon that enables you to perform Pan/Tilt/Zoom will appear.
PIP
Switches to PIP mode.
PIP is an acronym for “Picture In Picture”, which enables you to display a sub screen on the
Single Live screen.
ZOOM
Enlarges the screen of the selected channel twice.
SEQ
Switches to auto sequence mode.
SEQ is short for “Sequence”, which will transit the channel screen automatically at a
specified interval.
Freeze
Stops the live screen temporarily.
Search
Moves to the Search menu.
Play
Plays the video recording.
English _1
00000A_SHR-3040_ENG.indb 17
2009-06-10 오후 3:38:36
CH1
live
CH11
CH12
CH13
CH14
CH15
Mode Switch
CH5
CH6
CH7
CH8
CH9
CH3
CH4
CH16
You can use the channel buttons on the remote control or the front panel to switch to a single or 4-split mode for
each channel.
1. Press the channel button on the front panel, remote control or control icon, or click the channel icon in the
Launcher menu.
The selected channel will be displayed in single mode.
CH6
CH10
CH13
CH14
. Press the [CH-]CH5or [CH+] button
on the remote CH9
control to move
to the previous or
next channel.
. Press the [MODE] button on the remote control or the front panel, or click the split screen icon <
Launcher menu to switch to 4-split mode.
CH7
M
CH3
CH4
CH7
CH8
CH11
CH12
CH15
CH16
CH7
CH10
CH4
CH1
CH2
CH4
CH7
CH6
CH8
CH11
CH12
CH15
CH16
` Ex) If you select CH 3 and select split mode again
CH3
CH5
CH8
> in the
CH9
CH7
CH2
CH3
CH1
CH4
CH2
CH3
CH5
CH1
CH6
CH5
CH1
CH2
CH6
CH8
CH1
CH7
CH2
CH8CH3
CH4
CH4
CH8
CH4
;
CH1
CH2 CH2
CH1
CH3 CH5
CH9
CH10
CH9
CH11
CH5
CH10
CH12
CH1
CH6 CH12
CH7
CH11
CH13
CH3
CH14
CH13
CH15
CH4
CH14
CH16
CH9
CH4
CH3 CH5 CH7
CH15CH4 CH16
CH6 CH8
CH10
CH11
CH12
4 Split Screen
CH13
CH14
CH3
CH2
;
CH2
CH6
CH5
CH9
CH1
CH3
CH16
CH7
CH1
CH6
CH1
CH3
CH4
CH4
CH3
CH9
CH1
CH5
CH4
CH4
CH3
CH6
CH5
PIP Display
CH2
CH2
You
view aCH5sub screen in the lower right sideCH2
for the other
inCH4Single
CH3 canCH4
CH2 channel
CH3
CH5 Live Screen.
CH6
1. Press the [PIP] button on the remote control or the front panel, or click <
CH6
CH7
CH3
Launcher menu.
CH2
CH3
CH2
CH7
CH4
CH8
.
CH1
CH9
CH8
CH10
CH12
CH13
CH3
CH1the [PIP]
CH9
Press
CH1 or click <
button again,
The PIP screen CH1
disappears. CH2
CH11
CH12
M
CH1
CH2
CH13
CH5
CH6
CH1
>.CH4
CH7 CH1 CH8
CH8
CH3
CH10
CH4
4
CH15
CH7
CH1
CH1
CH11 SETUP”.
CH12
CH5 MENU
CH6 > CONFIGURATION
CH7
CH8
in <PIP SCREEN> from “MAIN
>CH10
INTERVAL
(Page 33)
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH3
CH1
CH2
CH3
CH4
CH5
CH1
CH6
CH2
CH3
CH7
CH8
CH4
CH9
CH5
CH3
CH6
CH7
CH8
CH9
CH2
CH1
CH4
CH10
18_ live
CH13
CH2
CH11
CH14
CH1
CH9
CH13
CH2
CH1
CH1
CH1
CH12
CH11
CH8
CH5
` The sub screen automatically switches at the specified interval, which can be adjusted
CH1
1
CH6
> in the
CH4
CH1
CH2
CH1
CH3
CH4
CH2
CH4
CH12
CH15
CH10
CH11
CH12
CH13
CH14
CH15
CH16
00000A_SHR-3040_ENG.indb 18
CH2
CH2
4 Split Screen
CH8
CH2
CH3
CH1
CH1
Single Screen of CH 3
CH15
CH2
2009-06-10 오후 3:38:37
CH6
Zoom
This is available in Live mode where the screen of the selected channel will be enlarged by 2x.
1. Press and hold the [ZOOM] button on the remote control or the front panel, or click <
> in the Launcher
menu.
The selected channel will be enlarged by 2x, while CH 1 will be enlarged to fit the screen in 4-split mode.
M
` In an enlarged screen, move the cursor to scroll through the screen.
CH1
CH2
CH3
Auto Sequence
CH9
CH10
CH11
CH12 CH4
CH5
CH6
CH9
CH10
CH11
CH12
CH5
CH6
CH9
CH10
CH11
CH12 CH4CH4
CH5
CH6
CH9
CH10 CH14
CH11 CH15
CH12 CH16
CH13
CH3
CH7
CH8
CH9
CH9
CH10
CH11 CH15
CH12 CH16
CH13
CH14
CH3
CH7
CH8
CH9
CH13
CH14
CH15
CH16
CH3
CH7
CH8
CH9
CH13
CH14
CH15
CH16
CH3
CH7
CH8
CH9
CH13
CH14
CH15
CH16
CH3
CH7
CH8
CH9
CH2
CH2
CH2
CH2
CH2
CH4
CH4
CH4
CH4
CH4
! live
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH4
CH1
CH2
CH3
CH1 orCH2click
CH3
CH4
CH1
CH2
CH3
. Press the [ZOOM] button again,
>.
CH5
CH6 <CH4
CH7
CH8CH1
CH1
CH2
CH3
CH1
CH2
CH3
CH5
CH6
CH7
CH8CH1
CH1
CH2
CH3
CH5
CH6
CH7
CH8
CH1
CH4
CH5
CH6
The zoom mode will be cancelled.
CH5
CH6
CH7
CH8
CH4
CH5
CH6 CH1CH1
CH5
CH6
CH7
CH8
CH2
CH2
CH2
CH2
CH2
CH3
CH1
CH3
CH1
CH3
CH1
CH3
CH1
CH3
CH1
CH4
CH5
CH6
CH4
CH5
CH6
CH4
CH5
CH6
CH4
CH5
CH6
CH4
CH5
CH6
You can view the 4 Single Live channels in sequence.
1. In Live mode, press and hold the [SEQ] button on the remote control or the front
CH2
CH3
CH4
CH5
panel, or click <
> in the Launcher menu. CH2CH2
CH2
CH3
CH4
CH5
CH2
CH3
CH4
CH5
CH2
CH2
CH3
CH4
CH5
CH2
CH6
CH3
CH4
CH5
CH2
CH7
CH3 CH2
CH6
CH7
CH3
CH6
CH7
CH3
CH6
CH7
CH3
CH1
CH7
CH3
CH9
CH8
CH4CH6
CH1
CH9
CH8
CH4
CH1
CH9
CH8
CH1
CH4
CH1
CH9
CH8
CH1
CH4
CH1
CH10
CH11
CH12
CH13
CH1
CH5
CH6
CH7
CH8
CH9
CH8
CH1
CH4
CH1
CH10
CH11
CH12
CH13
CH5
CH6
CH7
CH8
CH1
CH10
CH11
CH12
CH13
CH5
CH6
CH7
CH8
CH1
CH10
CH11
CH12
CH13
CH5
CH6
CH7
CH8
CH1
CH10
CH11
CH12
CH13
CH5
CH6
CH7
CH8
. Press the [SEQ] button again, or click <
Auto Sequence will be cancelled.CH1CH1
M
>.
` The switch interval can be adjusted in <SEQUENCE SCREEN> from
CH2
CH2
CH2
CH2
CH2
“MAIN MENU > CONFIGURATION > INTERVAL SETUP”. (Page 33)
Freeze
CH1
CH2
CH3
CH1
CH2
CH3
CH1
CH2
CH3
CH1
CH1
CH2
CH3
CH1
CH1
CH2
CH3
CH1
CH4
CH5
CH6
CH4
CH5
CH6 CH1CH1
CH4
CH5
CH6
CH4
CH5
CH6
CH4
CH5
CH6
CH3
CH7
CH8
CH9
CH3
CH7
CH8
CH9
CH3
CH7
CH8
CH9
CH3
CH7
CH8
CH9
CH3
CH7
CH8
CH9
CH4
CH1
CH1
CH1
CH1
CH1
CH1
CH2
CH2
CH2
CH2
CH2
This is available in Live mode where the Live screen will be stopped temporarily.
CH1
CH1
CH1
1. Press the [FRZ] button on theCH1CH1remote control, or click <
The Live screen will be stopped temporarily.
CH4
CH4
CH4
> in the Launcher
CH4 menu.
CH4
` If you press the [FRZ] button and selected a desired channel in a split mode, the selected screen alone will be stopped
temporarily or resumed.
CH10
CH11
CH12
CH10
CH11
CH12
CH10
CH11
CH12
CH10
CH11
CH12
CH10
CH11
CH12
CH13
CH14
CH15
CH13
CH14
CH15
CH13
CH14
CH15
CH13
CH14
CH15
CH13
CH14
CH15
CH16
CH16
CH16
CH16
CH16
. Press the [FRZ] button again, or click <
Freeze will be cancelled.
>.
CH5
CH5
CH5
CH5
CH5
CH6
CH6
CH6
CH6
CH6
CH9
CH9
CH9
CH9
CH9
CH10
CH10
CH10
CH10
CH10
CH13
CH13
CH13
CH13
CH13
CH14
CH14
CH14
CH14
CH14
CH7
CH7
CH7
CH7
CH7
CH8
CH8
CH8
CH8
CH8
CH11
CH11
CH11
CH11
CH11
CH12
CH12
CH12
CH12
CH12
CH15
CH15
CH15
CH15
CH15
CH16
CH16
CH16
CH16
CH16
CH7
CH2
CH3
CH4
CH7
CH2
CH3
CH4
CH7
CH2
CH3
CH4
CH7
CH2
CH3
CH4
CH5
CH6
CH1
CH8
CH7
CH2
CH3
CH4
CH5
CH6
CH1
CH8
CH5
CH6
CH1
CH8
CH5
CH6
CH1
CH8
CH5
CH6
CH1
CH8
CH9
CH10
CH11
CH12
CH9
CH10
CH11
CH12
CH9
CH10
CH11
CH12
CH9
CH10 CH14
CH11 CH15
CH12 CH16
CH13
CH9
CH10
CH11
CH12
CH13
CH14
CH15
CH16
CH13
CH14
CH15
CH16
CH13
CH14
CH15
CH16
CH13
CH14
CH15
CH16
CH1
CH1
CH1
CH1
CH1
CH3
CH3
CH3
CH3
CH3
CH2
CH2
CH2
CH2
CH2
CH1
CH1
CH1
CH1
CH1
English _19
00000A_SHR-3040_ENG.indb 19
2009-06-10 오후 3:38:38
live
recOrD
You can make recording manually in Live mode.
Other than in manual mode, recording will proceed as set in the Schedule menu.
1. Press the [rec] button on the remote control or the front panel,
or click <
> in the Launcher menu.
Recording will start while the button switches to Stop mode.
. Press the [rec] button again, or click <
Recording will be stopped.
M
2009/05/01
00:00:01
14D
2009/05/01
00:00:01
14D
>.
` You can set detailed options in “MAIN MENU > RECORD”.
` If the HDD is full in the condition where the Overwrite option in
“HDD MANAGEMENT” is set to <DISABLE>, recording will not
proceed further.
` Recording will be deactivated during data backup.
PtZ
You can adjust the angle of a PTZ-supported camera in the PTZ menu.
1. Press and hold the [PtZ] button on the remote control or the
front panel, or click <
> in the Launcher menu.
The PTZ direction pad will appear.
. Use the 8-direction arrows to adjust the camera angle.
. In the center <
> key, Click <
> to zoom in, and select
the lower <
> key to zoom out.
. Press the [PtZ] button again, or click <
The PTZ direction pad will disappear.
>.
0_ live
00000A_SHR-3040_ENG.indb 20
2009-06-10 오후 3:38:42
searcH
You can perform the search for recorded data by the time or by the search criteria such as an event.
1. Press the [searcH] button on the remote control, or click
<
> in the Launcher menu.
The Search menu appears.
DATE/TIME SEARCH
EVENT SEARCH
! live
. Use the direction buttons on the remote control or the front
panel, or use the cursor to select one from menu items of
Percent, Date/Time, and Event.
SEARCH
PERCENT SEARCH
. Specify search criteria for each item and click <Play> in the
lower screen.
The selected video data will be played.
EXIT
` To return to the previous menu, click <ESC>.
` You can also move the wheel of the mouse up or down to increase or decrease the setting value.
Percent search
You can select a start point in the percent bar showing the
amount of recorded data in the HDD.
Use the cursor to select a desired point in the section bar, or
use the [+/-] button on the remote control, or the left/right
button of the mouse to specify the percent (“%”) in the bar.
PERCENT SEARCH
START
2009/ 05/01
00:00:06
END
2009/ 05/01
00:00:20
TARGET
2009/ 05/01
00:00:06
PERCENT
92%
` Right-click will decrease the number; Left-click will increase the
number.
PLAY
ESC
Date/time search
You can search for data by the date and time.
If you select <Date/time searcH>, the start and end times
will be listed.
DATE/TIME SEARCH
START
2009/ 05/01
00:00:06
END
2009/ 05/01
00:00:20
TARGET
2009/ 05/01
00:00:06
The time point that you set in <tarGet> will be displayed in
the list.
` If you specify a time point out of range, an error message of <INPUT
DATE TIME ERROR> will be displayed.
PLAY
ESC
English _1
00000A_SHR-3040_ENG.indb 21
2009-06-10 오후 3:38:44
live
event search
You can check and search for contents of a list of events such
as sensor, motion detection, and video loss.
Select <eveNt searcH> to display a list of events with
information of the occurrence time and date.
If you select an event to play, the selected event will be played
instantly.
EVENT SEARCH
DATE/TIME
CHANNEL
EVENT
------------------------------------------------2009/05/01 00:00:06
2
LOSS
2009/05/01 00:00:07
1
LOSS
2009/05/01 00:00:08
1
LOSS
2009/05/01 00:00:09
1
MOTION
2009/05/01 00:00:10
1
MOTION
/
/
:
:
-/
/
:
:
-/
/
:
:
-/
/
:
:
-/
/
:
:
-PAGE
001/001
ESC
Play
In Live mode, press the [+] button on the remote control or the front
panel or click on the <
> menu from the launcher menu to play
forward video data in the HDD from the last run point.
M
2009/05/01
00:00:01
14D
` Each icon in the Launcher menu will work the same as in the play
bar on the remote control. (Page 10)
_ live
00000A_SHR-3040_ENG.indb 22
2009-06-10 오후 3:38:46
eveNt mONitOriNG
This will display a specific event such as alarm and event on the screen of each channel.
The event will be displayed regardless of the schedule setting.
to set the event update
INTERVAL SETUP
SEQUENCE SCREEN
01 SEC
PIP SCREEN
01 SEC
EVENT UPDATE
600 SEC
. If an event specified in the recording schedule occurs, the
event update will be made.
` For more information, refer to “SCHEDULE SETUP”. (Page 29)
! live
1. Specify a time in “maiN meNu > cONFiGuratiON >
iNterval setuP > eveNt uPDate”.
Set the time between 10 and 990 seconds by the 10
seconds.
` For more information, refer to “INTERVAL SETUP”. (Page 33)
OK
DEFAULT
ESC
~ A video loss event will be updated only while recording is in process.
~ An alarm list will be updated only if the recording schedule has been set to Alarm.
~ A motion event will be updated only if the recording schedule has been set to Motion.
~ Alarm and motion events will be updated only if the recording schedule has been set to Alarm + Motion.
to update the event list
` Ex) If you set the event update interval to 10 seconds, the next event will be updated in at least 10 seconds.
Event Occurs
Event Ends
Event Occurs
Event Occurs
10 seconds
Updates the event list
Ignore list registration
Updates the event list
English _
00000A_SHR-3040_ENG.indb 23
2009-06-10 오후 3:38:47
live
CH2
CH3
CH5
CH6
eveNt mONitOriNG ON tHe sPOt mONitOr
CH8
CH9
Apart
from theCH4
Live screen, you can use the spot monitor to monitor an event from a specific channel through the
CH3
SPOT OUT port.
CH1
CH2
1. Specify an interval and use of the popup in “eXterNal Device
> sPOt setuP”.
According to your settings, the spot monitor will be activated
when an event occurs.
SPOT SETUP
SWITCHING INTERVAL
ALARM POPUP
OFF
MOTION POPUP
OFF
EVENT POPUP DURATION
` For more information, refer to “SPOT SETUP”. (Page 41)
03 SEC
05 SEC
OK
DEFAULT
ESC
~ The spot monitor is defaulted to Auto Sequence according to the interval.
If multiple events occur simultaneously, the events from the lower channel will be notified first with popup
messages.
CH9
CH10
~ If the spot
monitor switches
from channel 1 (the first event) to channel 2 (the second one), a new event from
CH13
CH14
channel 1 within the event popup duration will not display a new popup.
spot event Popup
CH11
Event Occurs
CH15
CH12
CH16
Event Occurs
Popup Duration
CH1
CH3
CH1
CH2
CH2
_ live
00000A_SHR-3040_ENG.indb 24
2009-06-10 오후 3:38:48
setup
Using the Menu
You can configure the menu settings of screen display, record, configuration, external device, backup, language,
firmware upgrade and system reset.
` You can use the remote control or mouse to select each one of the menu items above.
! setup
M
To fast access a desired menu, it is recommended to learn about using the buttons and remote control in advance.
Using the mouse
In the Launcher menu, click <
Button
> and enter the password to log in; The “MAIN MENU” appears.
Description
Used to adjust the setting in the menu. (increase / decrease)
Wheel
Adjust the volume level (+, -) in Live/Play mode.
Right
Used to adjust the setting in the menu. (decrease)
Used to adjust the setting in the menu. (increase)
Left
Use this to run a Launcher menu. (click a desired icon)
Using the buttons on the remote control or the front panel
In Live mode, press the [MENU] button to access the “MAIN MENU” through the login process.
Button Name
Description
Direction Buttons
$%_ +
Used to move through the menu items.
Confirm
OK
Used to confirm your input or setting, or change the setting.
(Increase/Decrease)
+/-
+/-
Used to change the menu setting. (Increase/Decrease)
Menu
MENU
Used to access the main menu or move to the previous menu.
English _25
00000A_SHR-3040_ENG.indb 25
2009-06-10 오후 3:38:48
setup
DisPlay setuP
You can configure the settings of VGA, Screen Display and OSD.
vGa setup
1. Press the [meNu] button on the remote control or the
front panel.
The “Dvr lOG-iN” dialog appears.
. Enter the password and select <eNter>.
The “maiN meNu” screen appears.
. Use the up/down ($%) button to select <DisPlay
setuP>, and press [OK].
The “DisPlay setuP” screen appears.
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
ENGLISH
SHUTDOWN
EXIT
. Use the up/down ($%) button to select <DisPlay
setuP>, and press [OK].
The “vGa setuP” screen appears.
DISPLAY SETUP
VGA SETUP
SCREEN DISPLAY
OSD SETUP
ESC
. Set the video resolution.
~ RESOLUTION: Select one from 640X480, 800X600,
1024X768, and 1280X1024.
VGA SETUP
RESOLUTION
800 * 600/60HZ
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to
the factory default.
. To return to the previous menu, select <esc>.
OK
DEFAULT
ESC
_ setup
00000A_SHR-3040_ENG.indb 26
2009-06-10 오후 3:38:50
screen Display setup
See the previous section to repeat steps 1~3. (Page 26)
. Use the up/down ($%) button to select <screeN
DisPlay>, and press [OK].
The “screeN DisPlay” screen appears.
DISPLAY SETUP
VGA SETUP
SCREEN DISPLAY
OSD SETUP
. Use the up/down ($%) button to move to a desired item.
~ VERTICAL POSITION: Used to move the input video up
or down. (-5~5)
~ HORIZONTAL POSITION: Used to move the input video
to the left or right. (-31~31)
! setuP
ESC
SCREEN DISPLAY
VERTICAL POSITION
0
HORIZONTAL POSITION
BORDER ENABLE
0
ON
BORDER COLOR
LIGHT GRAY
~ BORDER ENABLE: Specify the use of the border line.
~ BORDER COLOR: Specify the color of the border line.
OK
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to the factory default.
DEFAULT
ESC
. To return to the previous menu, select <esc>.
OsD setup
See the previous section to repeat steps 1~3. (Page 26)
. Use the up/down ($%) button to select <OsD setuP>,
and press [OK].
The “OsD setuP” screen appears.
DISPLAY SETUP
VGA SETUP
SCREEN DISPLAY
OSD SETUP
ESC
English _
00000A_SHR-3040_ENG.indb 27
2009-06-10 오후 3:38:52
setup
. Use the up/down ($%) button to set the “tOP OsD
OFFset”.
The icon bar in the upper corner of the Live screen will be
removed up or down.
OSD SETUP
TOP OSD OFFSET
0
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to
the factory default.
OK
. To return to the previous menu, select <esc>.
DEFAULT
ESC
recOrD
You can configure the record and recording schedule settings.
record setup
You can set options of the record quality, frame rate and pre alarm record.
1. Press the [meNu] button on the remote control or the
front panel.
The “Dvr lOG-iN” dialog appears.
. Enter the password and select <eNter>.
The “maiN meNu” screen appears.
. Use the up/down ($%) button to select <recOrD>, and
press [OK].
The “recOrD” setting screen appears.
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
ENGLISH
SHUTDOWN
EXIT
. Use the up/down ($%) button to select <recOrD
setuP>, and press [OK].
The “recOrD setuP” screen appears.
RECORD
RECORD SETUP
SCHEDULE SETUP
ESC
. Use the up/down ($%) button to move to a desired item.
~ QUALITY: Select the quality from Highest, High and
Normal.
The remaining time will change according to the quality.
~ FRAME RATE: Set the frame rate per second.
The higher the frame rate is, the more natural the video
becomes but the remaining recordable time will be
shortened.
RECORD SETUP
QUALITY
HIGH
FRAME RATE
30 FPS
PRE ALARM RECORD
OFF
------------------------------------------------HDD REMAINING
236GB/320GB
TIME REMAINING
D-14 H-11 M-25
OK
DEFAULT
ESC
_ setup
00000A_SHR-3040_ENG.indb 28
2009-06-10 오후 3:38:54
~ PRE ALARM RECORD: In event recording, set the advance recording time before an actual event.
J
` Pre alarm settings will be changed according to the frame rate.
~ HDD REMAINING: Shows the remaining and total capacity of the current HDD.
~ TIME REMAINING: Displays the expected recordable time in the “Date(D)/HOur(H)/miN(m)” format
based on the selected quality.
! setuP
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to the factory default.
. To return to the previous menu, select <esc>.
schedule setup
You can set the recording schedule.
See the previous section to repeat steps 1~3. (Page 28)
. Use the up/down ($%) button to select <scHeDule
setuP>, and press [OK].
The “scHeDule setuP” screen appears.
RECORD
RECORD SETUP
SCHEDULE SETUP
ESC
. Use the direction ($%_ +) buttons to move to a desired
box, and press [OK].
Each time you press the button, the box setting will switch
to “cONtiNue > mOtiON > alarm > mOtiON &
alarm > stOP recOrDiNG” in sequence.
~ ALL: Select this to set the entire week.
~ DAY: Select this to set a specific day of the week.
SCHEDULE SETUP
ALL
000204060810121416182022
SUN
MON
TUE
WED
THU
FRI
SAT
~ HOUR: Select this to set the time range.
You can set the time range by the two hours.
OK
DEFAULT
ESC
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to the factory default.
. To return to the previous menu, select <esc>.
English _
00000A_SHR-3040_ENG.indb 29
2009-06-10 오후 3:38:57
setup
cONFiGuratiON
You can configure the settings of HDD, Camera, Motion, Alarm, Interval, Date/Time, Password, and Buzzer.
HDD management
You can check the HDD model and its capacity, and set the Overwrite option and reset the HDD.
1. Press the [meNu] button on the remote control or the
front panel.
The “Dvr lOG-iN” dialog appears.
. Enter the password and select <eNter>.
The “maiN meNu” screen appears.
. Use the up/down ($%) button to select
<cONFiGuratiON>, and press [OK].
The “cONFiGuratiON” screen appears.
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
ENGLISH
SHUTDOWN
EXIT
. Use the up/down ($%) button to select <HDD
maNaGemeNt>, and press [OK].
The “HDD maNaGemeNt” screen appears.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
DATE/TIME SETUP
PASSWORD SETUP
BUZZER SETUP
ESC
. Check the current HDD for the model and specifications.
. Use the up/down ($%) button to move to a desired item.
~ OVERWRITE: When the HDD is full while this option is
set to <eNaBle>, the DVR will proceed with recording
by overwriting the existing data.
If set to <DisaBle>, the DVR will stop recording when
the HDD is full.
HDD MANAGEMENT
MODEL
WDC WD2500AAJS-22B4AO
SERIAL
WD-WCAT10703203
BLOCKS
488397168 LBA
SIZE
BANDWIDTH
P104
------------------------------------------------OVERWRITE
AUTO DELETION
ENABLE
OFF
<CAUTION>TOTALLY ERASE HDD DATA
~ AUTO DELETION: If you have set an auto deletion
CLEAR
period, the existing data before the specified time will
be deleted.
If you select <OFF>, auto deletion will be disabled.
If you have set auto deletion period, the <Overwrite> option will be set to <autOmatic>
automatically.
J
320 GB
OK
ESC
` If you have set an auto deletion period, the HDD recording data before the specified time will be deleted.
Ex) For D-03, data until 3 days ago will be deleted.
. When done, select <OK>.
Your setting will be applied.
If you select <clear>, the HDD will be cleared after the login process.
. To return to the previous menu, select <esc>.
0_ setup
00000A_SHR-3040_ENG.indb 30
2009-06-10 오후 3:39:00
camera setup
See the previous section to repeat steps 1~3. (Page 30)
. Use the up/down ($%) button to select <camera
setuP>, and press [OK].
The “camera setuP” screen appears.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
DATE/TIME SETUP
BUZZER SETUP
ESC
. Use the up/down ($%) button to move to a desired item.
~ CHANNEL: Select a channel to change the title.
~ TITLE: Move the cursor to the input box and use the
[OK, +, -] buttons to enter a name. (8 characters)
~ BRIGHTNESS: Adjust the screen brightness.
~ CONTRAST: Adjust the color contrast.
CAMERA SETUP
CHANNEL
CH1
TITLE
CAM01---
BRIGHTNESS
0
CONTRAST
10
SATURATION
4
HUE
-32
HORIZONTAL POSITION
LIVE DISPLAY
0
ON
~ SATURATION: Adjust the saturation.
~ HUE: Adjust the color tone.
! setuP
PASSWORD SETUP
OK
DEFAULT
ALL-DEFAULT
ESC
~ HORIZONTAL POSITION: Adjust the horizontal position for each channel screen.
~ LIVE DISPLAY: Turn on/off the Live screen.
` If you select <OFF>, the Live screen will not be displayed but the recording proceeds normally.
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the selected channel will be reset to the default, and if selecting
<all-DeFault>, all the channels will be reset to the factory default.
. To return to the previous menu, select <esc>.
English _1
00000A_SHR-3040_ENG.indb 31
2009-06-10 오후 3:39:01
setup
motion setup
You can specify an area to detect a motion.
If you select an area to detect a motion, the DVR will detect any motion occurring in that area.
See the previous section to repeat steps 1~3. (Page 30)
. Use the up/down ($%) button to select <mOtiON
setuP>, and press [OK].
The “mOtiON setuP” screen appears.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
DATE/TIME SETUP
PASSWORD SETUP
BUZZER SETUP
ESC
. Use the up/down ($%) button to move to a desired item.
MOTION SETUP
~ CHANNEL: Select a channel to set the motion detection.
CHANNEL
~ SENSITIVITY: Adjust the sensitivity of the motion detection.
SENSITIVITY
~ DURATION: Set the recording duration from the moment a motion is
detected. You can specify the duration between 2 and 99 seconds.
CH1
6
DURATION
SIZE
05
~ SIZE: Specify the number of cells to be selected at once.
Ex) If you select 3, a total of 9 cells (3X3) will be selected.
. Use the four direction ($%_ +) buttons and press [OK]
to set the motion area.
Motion detection is activated for the area that is selected in red.
2
OK
DEFAULT
ALL-DEFAULT
ESC
` By default, all cells are set to disabled.
` If you use the cursor to set the motion area, select a cell and set it to ‘ACTIVE/INACTIVE’.
Left-click a cell and drag it until a desired cell block is shaped.
When a desired block is selected, release the left button of the mouse.
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the selected channel will be reset to the default, and if selecting <all-DeFault>, all
the channels will be reset to the factory default.
. To return to the previous menu, select <esc>.
alarm setup
You can set the input system of the sensor that is connected to the DVR.
See the previous section to repeat steps 1~3. (Page 30)
. Use the up/down ($%) button to select <alarm
setuP>, and press [OK].
The “alarm setuP” screen appears.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
DATE/TIME SETUP
PASSWORD SETUP
BUZZER SETUP
ESC
_ setup
00000A_SHR-3040_ENG.indb 32
2009-06-10 오후 3:39:04
. Use the up/down ($%) button to move to a desired item.
~ CHANNEL: Select a channel to set the alarm.
` You can set the alarm for only one channel.
CHANNEL
CH1
TYPE
NORMAL OPEN
DURATION
05 SEC
OK
DEFAULT
ALL-DEFAULT
ESC
~ DURATION: Specify the duration for which the DVR makes the alarm recording when an alarm sounds.
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the selected channel will be reset to the default, and if selecting
<all-DeFault>, all the channels will be reset to the factory default.
! setuP
~ TYPE: Set the sensor input system.
- <DisaBle> : The sensor does not work.
- <NOrmal OPeN> : The sensor is always open.
The alarm will sound when the sensor is closed.
- <NOrmal clOse> : The sensor is always closed.
The alarm will sound when the sensor is open.
ALARM SETUP
. To return to the previous menu, select <esc>.
interval setup
You can specify the interval for Auto Sequence, or PIP (Picture In Picture) mode.
See the previous section to repeat steps 1~3. (Page 30)
. Use the up/down ($%) button to select <iNterval
setuP>, and press [OK].
. Use the up/down ($%) button to move to a desired item.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
DATE/TIME SETUP
PASSWORD SETUP
BUZZER SETUP
ESC
. Use the up/down ($%) button to move to a desired item.
~ SEQUENCE SCREEN: In Live full screen, specify the
auto sequence interval for each camera channel.
INTERVAL SETUP
SEQUENCE SCREEN
01 SEC
PIP SCREEN
01 SEC
EVENT UPDATE
600 SEC
~ PIP SCREEN: Specify the interval for auto sequence for
the sub picture in PIP mode.
~ EVENT UPDATE: Specify the interval of updating the
event list for incoming events.
If the interval is set to 10 seconds, the next event can be
updated 10 seconds after the first event was registered
to the event list.
OK
DEFAULT
ESC
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the selected channel will be reset to the default, and if selecting
<all-DeFault>, all the channels will be reset to the factory default.
. To return to the previous menu, select <esc>.
English _
00000A_SHR-3040_ENG.indb 33
2009-06-10 오후 3:39:07
setup
Date/time setup
You can configure the settings of Date/Time, Format, and Daylight Saving.
See the previous section to repeat steps 1~3. (Page 30)
. Use the up/down ($%) button to select <Date/time
setuP>, and press [OK].
The “Date/time setuP” screen appears.
. Use the up/down ($%) button to move to a desired item.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
~ DATE, TIME: Specify the date and time.
INTERVAL SETUP
~ DATE FORMAT: Select a date format for your area.
(Asian/European/American)
PASSWORD SETUP
DATE/TIME SETUP
BUZZER SETUP
~ HOUR FORMAT: Specify a time format to your
preference. (12 Hour/24 Hour)
ESC
~ MONTH FORMAT: Specify a month format to your
preference. (English, Numeric)
~ DST (Daylight Saving Time): Set whether to use DST.
If you select <ON> and specify the start and end dates,
the system time will be set one hour ahead of the local
standard time.
~ START: Specify the start time for DST in a format of
M(month)/D(day)/H(hour).
DATE/TIME SETUP
DATE
TIME
2009/ 05/01
00:00:43
DATE FORMAT
HOUR FORMAT
MONTH FORMAT
ASIAN
24HOUR
NUMERIC
DST
START
END
OFF
M-01 D-01 H-00
M-01 D-01 H-00
OK
~ END: Specify the end time for DST in a format of
M(month)/D(day)/H(hour).
J
DEFAULT
ESC
` If you set the DST option with one hour moved up, the recorded data of corresponding one hour will be lost.
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to the factory default.
. To return to the previous menu, select <esc>.
Password setup
You can replace the default password with a new one to your preference.
See the previous section to repeat steps 1~3. (Page 30)
. Use the up/down ($%) button to select <PasswOrD
setuP>, and press [OK].
The “PasswOrD setuP” screen appears.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
DATE/TIME SETUP
PASSWORD SETUP
BUZZER SETUP
ESC
_ setup
00000A_SHR-3040_ENG.indb 34
2009-06-10 오후 3:39:09
. Use the up/down ($%) button to move to a desired item.
~ USER ID: Select a user ID.
You will have a total of 10 IDs available including Admin.
- ADMIN: The administrator can set and perform all
features of the DVR.
USER ID
ADMIN
USER PW
--------
NEW PW
--------
CONFIRM
--------
0
1
2
3
4
5
6
7
8
9
ENTER
ESC
! setuP
- MANAGER: Can change the password and perform
backup. Can access menus of Client Setup, Backup,
Player, Search, and Remote Viewer using the Web
Viewer.
PASSWORD SETUP
- USER: Can change the password and perform
backup. Can access menus of Client Setup, Player, and Remote Viewer using the Web Viewer.
~ USER PW: Provide the default password.
~ NEW PW/CONFIRM: Provide a new password.
. Provide a new password and select <eNter> to apply the new password; if you enter an invalid
password, an error message will appear.
. When done, select <esc>.
Your setting will be applied.
Buzzer setup
You can set whether to use the buzzer sound.
See the previous section to repeat steps 1~3. (Page 30)
. Use the up/down ($%) button to select <BuZZer
setuP>, and press [OK].
The “BuZZer setuP” screen appears.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
DATE/TIME SETUP
PASSWORD SETUP
BUZZER SETUP
ESC
. Use the up/down ($%) button to move to a desired item.
~ KEY TONE: Set the key tone of the button.
~ VIDEO LOSS: Set to sound the buzzer if a video loss
occurs.
BUZZER SETUP
KEY TONE
OFF
VIDEO LOSS
OFF
ALARM ACTIVE
OFF
MOTION DETECT
OFF
~ ALARM ACTIVE: Set to sound the buzzer on a sensor
signal input.
~ MOTION DETECT: Set to sound the buzzer when a
motion is detected.
OK
DEFAULT
ESC
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to the factory default.
. To return to the previous menu, select <esc>.
English _
00000A_SHR-3040_ENG.indb 35
2009-06-10 오후 3:39:11
setup
eXterNal Device
You can configure the settings of Network, PTZ, Mouse, Audio, and Spot output.
tcP/iP setup
You can view the Live screen, configure the DVR settings, and backup HDD data remotely via the network.
iP setup
1. Press the [meNu] button on the remote control or the
front panel.
The “Dvr lOG-iN” dialog appears.
. Enter the password and select <eNter>.
The “maiN meNu” screen appears.
. Use the up/down ($%) button to select <eXterNal
Device>, and press [OK].
The “eXterNal Device” screen appears.
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
ENGLISH
SHUTDOWN
EXIT
. Use the up/down ($%) button to select <tcP/iP
setuP>, and press [OK].
The “tcP/iP setuP” screen appears.
EXTERNAL DEVICE
TCP/IP SETUP
PTZ SETUP
MOUSE SETUP
AUDIO SETUP
SPOT SETUP
ESC
. Use the up/down ($%) button to select <iP setuP>, and
press [OK].
The “iP setuP” screen appears.
TCP/IP SETUP
IP SETUP
DDNS SETUP
ESC
_ setup
00000A_SHR-3040_ENG.indb 36
2009-06-10 오후 3:39:13
. Use the up/down ($%) button to move to a desired item.
IP SETUP
~ MAC ADDRESS: Shows information of the network that
is assigned to the DVR.
MAC ADDRESS
DHCP MODE
~ DHCP MODE: If you set this to <autO>, IP address
and other network settings will be assigned from the
DHCP server. (Only the IP port can be set manually)
If you set this to <maNual>, you can specify all of the
settings below:
IP PORT
IP ADDRESS
GATEWAY
SUBNET
00-0A-A2-08-08-F3
MANUAL
IP DETECT
50000
192.168.001.160
192.168.001.001
255.255.255.000
BANDWIDTH
WEB SERVER PORT
1Mbps
00080
OK
ESC
! setuP
~ IP PORT, IP ADDRESS, GATEWAY, SUBNET: Manually
enter the value according to the network environment if
you set the DHCP Setup to Manual.
. When done, select <OK>.
Your setting will be applied.
. To return to the previous menu, select <esc>.
DDNs setup
You can specify a DDNS site to access when a remote user connects to the network.
what is DDNs?
DDNS is an acronym for Dynamic DNS(Domain Name System).
DNS(Domain Name System) is a domain service to redirect the IP address (ex: 64.233.189.104) to a
name that the user can remember with ease (ex: www.google.com).
DDNS(Dynamic DNS) is the IP registration service that registers a domain name that the user remembers
and a changed IP address with the DDNS server so that the user can redirect to the registered domain
name if the previous IP address is changed in a dynamic IP environment.
checking the DDNs address
A DDNS address consists of <english lower case “g”> + <mac address 6 digits from the end> +
<websamsung.net>.
` Ex) If 6 digits of the MAC address of the DVR are <00:00:f0> from the end:
g + 0000f0 + websamsung.net = g0000f0.websamsung.net
See the previous section to repeat steps 1~4. (Page 36)
. Use the up/down ($%) button to select <DDNs setuP>,
and press [OK].
The “DDNs setuP” screen appears.
. Use the up/down ($%) button to move to a desired item.
DDNS SETUP
DDNS ENABLE
OFF
REGISTER
DDNS STATUS
~ DDNS ENABLE: Set whether to use the DDNS.
~ DDNS STATUS: If you set DDNS Enable to <ON>, you
will see a message of the status of the DDNS on the
screen.
. When done, select <OK>.
Your setting will be applied.
http://g0808f3.websamsung.net:80
OK
ESC
. To return to the previous menu, select <esc>.
English _
00000A_SHR-3040_ENG.indb 37
2009-06-10 오후 3:39:15
setup
PtZ setup
You can set the model, ID and speed of the PTZ camera for each channel including the size and cord.
command setup
See the previous section to repeat steps 1~3. (Page 36)
. Use the up/down ($%) button to select <PtZ setuP>,
and press [OK].
The “PtZ setuP” screen appears.
EXTERNAL DEVICE
TCP/IP SETUP
PTZ SETUP
MOUSE SETUP
AUDIO SETUP
SPOT SETUP
ESC
. Use the up/down ($%) button to select <cOmmaND
setuP>, and press [OK].
The “cOmmaND setuP” screen appears.
PTZ SETUP
COMMAND SETUP
SPEED SETUP
ESC
. Use the up/down ($%) button to move to a desired item.
~ CHANNEL: Select a channel.
~ MODEL: Select a model available.
~ PTZ ID: Specify an ID number.
~ BAUDRATE: Set the bit rate for the applicable model.
COMMAND SETUP
CHANNEL
MODEL
PTZ ID
BAUDRATE
CH2
SAMSUNG
000
002400 BPS
COMMAND
LENGTH
CODE
P/T RIGHT-DOWN
09
A0 00 00 01
00 0A 3F 3F
76
OK
~ COMMAND: Select a command.
~ LENGTH: Specify the duration of each command.
~ CODE: Displays a code that is associated with the
command.
DEFAULT
ALL-DEFAULT
ESC
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the selected channel will be reset to the default, and if selecting
<all-DeFault>, all the channels will be reset to the factory default.
. To return to the previous menu, select <esc>.
_ setup
00000A_SHR-3040_ENG.indb 38
2009-06-10 오후 3:39:16
speed setup
You can set the pan and tilt speed of the PTZ camera.
See the previous section to repeat steps 1~3. (Page 36)
. Use the up/down ($%) button to select <PtZ setuP>,
and press [OK].
The “PtZ setuP” screen appears.
PTZ SETUP
COMMAND SETUP
SPEED SETUP
! setuP
. Use the up/down ($%) button to select <sPeeD
setuP>, and press [OK].
The “sPeeD setuP” screen appears.
ESC
. Use the up/down ($%) button to move to <PaN sPeeD>
or <tilt sPeeD> and specify the applicable speed.
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to
the factory default.
SPEED SETUP
PAN SPEED
7
TILT SPEED
7
. To return to the previous menu, select <esc>.
OK
DEFAULT
ESC
English _
00000A_SHR-3040_ENG.indb 39
2009-06-10 오후 3:39:18
setup
mouse setup
You can adjust the operational sensitivity of the cursor.
See the previous section to repeat steps 1~3. (Page 36)
. Use the up/down ($%) button to select <mOuse
setuP>, and press [OK].
The “mOuse setuP” screen appears.
EXTERNAL DEVICE
TCP/IP SETUP
PTZ SETUP
MOUSE SETUP
AUDIO SETUP
SPOT SETUP
ESC
. Specify the <seNsitivity>.
` The higher the value is, the faster the mouse moves.
MOUSE SETUP
SENSITIVITY
3
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to
the factory default.
. To return to the previous menu, select <esc>.
OK
DEFAULT
ESC
0_ setup
00000A_SHR-3040_ENG.indb 40
2009-06-10 오후 3:39:19
audio setup
You can adjust the I/O volume for the channel.
During video recording, sound from the selected channel will be recorded as well.
See the previous section to repeat steps 1~3. (Page 36)
. Use the up/down ($%) button to select <auDiO
setuP>, and press [OK].
The “auDiO setuP” screen appears.
EXTERNAL DEVICE
TCP/IP SETUP
PTZ SETUP
! setuP
MOUSE SETUP
AUDIO SETUP
SPOT SETUP
ESC
. Use the up/down ($%) button to move to a desired item.
~ CHANNEL: Select a channel for which you want to
adjust the I/O volume.
If you set it to <OFF>, the audio icon will be grayed out
and no sound will be recorded.
AUDIO SETUP
CHANNEL
CH1
INPUT VOLUME
15
OUTPUT VOLUME
03
~ INPUT VOLUME: Specify the input volume.
If you specify <00> for the volume, audio input signal will
be zero (0).
OK
~ OUTPUT VOLUME: Specify the output speaker volume.
DEFAULT
ESC
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to the factory default.
. To return to the previous menu, select <esc>.
spot setup
Apart from the Live screen, you can use the spot monitor to monitor a specific channel through the SPOT
OUT port.
See the previous section to repeat steps 1~3. (Page 36)
. Use the up/down ($%) button to select <sPOt setuP>,
and press [OK].
The “sPOt setuP” screen appears.
EXTERNAL DEVICE
TCP/IP SETUP
PTZ SETUP
MOUSE SETUP
AUDIO SETUP
SPOT SETUP
ESC
English _1
00000A_SHR-3040_ENG.indb 41
2009-06-10 오후 3:39:21
setup
. Use the up/down ($%) button to move to a desired item.
SPOT SETUP
~ SWITCHING INTERVAL: Specify the switching interval
for the spot monitor.
SWITCHING INTERVAL
~ ALARM POPUP: Set to display a popup message if an
alarm signal is detected.
EVENT POPUP DURATION
03 SEC
ALARM POPUP
OFF
MOTION POPUP
OFF
05 SEC
~ MOTION POPUP: Set to display a popup message if a
motion signal is detected.
OK
~ EVENT POPUP DURATION: Specify the event popup
duration.
DEFAULT
ESC
. When done, select <OK>.
Your setting will be applied.
If you select <DeFault>, the settings will be restored to the factory default.
. To return to the previous menu, select <esc>.
BacKuP
You can backup HDD recording data on a USB storage device.
Backup
1. Press the [meNu] button on the front panel or remote
control.
The “Dvr lOG-iN” dialog appears.
. Enter the password and select <eNter>.
The “maiN meNu” screen appears.
. Use the up/down ($%) button to select <BacK-uP>, and
press [OK].
The “BacK-uP” screen appears.
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
ENGLISH
SHUTDOWN
EXIT
. Connect the USB device and select <cHecK usB>.
A device list of the search results will appear with device
information.
BACK-UP
HDD
START
END
2009/ 05/01
2009/ 05/01
MEDIA
PARTITION
START
END
SIZE
CHECK USB
/
MB
BACK-UP
/
00:00:06
00:00:20
:
->
:
MB
ESC
_ setup
00000A_SHR-3040_ENG.indb 42
2009-06-10 오후 3:39:24
. Specify the start time, date range and size to backup.
` You can specify the backup size for a backup device. The end time
and date will be set according to the backup size.
` You can change the start time and date if you want to.
HDD
START
END
2009/ 05/01
2009/ 05/01
MEDIA
PARTITION
START
END
SIZE
. Select <BacK-uP>.
USB backup gets started.
` During backup, recording will be stopped and the Live screen
will be lost in the viewer.
00:00:43
00:00:15
3838MB/ 3848MB
2009/ 05/01
00:00:43
2009/ 05/01
00:00:14
003836MB ->
3444MB
USB STORAGE IS AVAILABLE
CHECK USB
BACK-UP
ESC
. When backup is done, the start time will be moved later than the completion time, and the end time will be
adjusted according to the backup size.
! setuP
J
BACK-UP
. Launch the web viewer from a remote PC where you can check the backup data using the <Player>.
` You can also play the data using <AUTO PLAYER> that is created in the USB storage device after the backup.
system messages
You will see the following messages when the DVR has checked USB storage devices.
If no USB storage is inserted
If a USB storage is recognized
USB STORAGE IS NOT AVAILABLE.
CHECK USB
CHECK USB
THERE IS A FREE SPACE ON STORAGE.
RECONNECT THE USB STORAGE.
USB STORAGE IS AVAILABLE.
CONNECT THE OTHER USB STORAGE.
During backup
START WRITING IN USB STORAGE.
FINISH WRITING IN USB STORAGE.
Error messages
THERE IS A PROBLEM ON USB PORT
(If USB port does not operate properly)
USB STORAGE IS FULL. (No free space in the USB device)
CHANGE WRITE PROTECT MODE. (Write protection mode )
FILE SYSTEM IS NOT SUPPORTED.
(If the file system is not supported)
SIZE IS LARGER THAN FREE SPACE.
(If backup size is larger than the free space in the USB
device)
English _
00000A_SHR-3040_ENG.indb 43
2009-06-10 오후 3:39:24
setup
Firmware uPGraDe
You can upgrade the DVR firmware with the latest version.
upgrade
1. Press the [meNu] button on the front panel or remote
control.
The “Dvr lOG-iN” dialog appears.
. Enter the password and select <eNter>.
The “maiN meNu” screen appears.
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
ENGLISH
SHUTDOWN
EXIT
. Use the up/down ($%) button to select <Firmware
uPGraDe>, and press [OK].
The “Firmware uPGraDe” screen appears.
. Connect the USB device that stores upgradeable files.
FIRMWARE UPGRADE
CURRENT VER
V 0.01_090326
UPGRADE VER
FILE:
. Select <cHecK usB>.
CHECK USB
. If there founds any upgradeable file, select <uPGraDe>.
UPGRADE
ESC
FIRMWARE UPGRADE
. After the login process, the DVR will perform the upgrade
step by step.
CURRENT VER
. When done, restart the player.
YOU ARE TRYING TO UPGRADE THE FIRM-
J
V 0.01_090326
UPGRADE VER
FILE:
V0.01_090326
SHR-3040_V0.01_090326.BIN
WARE WITH SAME OR PREVIOUS VERSION.
` During the firmware upgrade, recording will be stopped and
the Live screen in the viewer may skip.
` As the player performs upgrade with the first one if there is
more than one upgradeable file in the USB device, so ensure
that there should be only one upgrade file in the USB device.
PRESS UPGRADE
CHECK USB
UPGRADE
ESC
_ setup
00000A_SHR-3040_ENG.indb 44
2009-06-10 오후 3:39:26
FactOry DeFault
You can restore the settings to the factory default.
Factory Default
. Enter the password and select <eNter>.
The “maiN meNu” screen appears.
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
! setuP
1. Press the [meNu] button on the front panel or remote
control.
The “Dvr lOG-iN” dialog appears.
LANGUAGE
ENGLISH
SHUTDOWN
EXIT
. Use the up/down ($%) button to select <FactOry
DeFault>, and press [OK].
The “FactOry DeFault” screen appears.
. Use the up/down ($%) button to move to an item to reset
and select <ON>.
. Select <DeFault> in the bottom.
The selected item will be reset to the factory default.
` To reset all items, set <ALL> to <ON> and select <DEFAULT>.
FACTORY DEFAULT
ALL
OFF
------------------------------------------------DISPLAY SETUP
OFF
RECORD SETUP
OFF
SCHEDULE SETUP
OFF
CAMERA SETUP
OFF
CONFIGURATION
OFF
EXTERNAL DEVICE
OFF
CHANGE FACTORY DEFAULT
LOAD SETUP
SAVE SETUP
DEFAULT
ESC
changing Factory Default
You can customize the factory default settings to your preference.
1. Connect a FAT 32 formatted USB storage device and
select <save setuP>.
When done, you will see a message of “lOaD setuP
success” on the screen.
` All current settings of the DVR will be saved to the USB device.
It takes 5 to10 seconds, depending on the USB device.
FACTORY DEFAULT
ALL
OFF
------------------------------------------------DISPLAY SETUP
OFF
RECORD SETUP
OFF
SCHEDULE SETUP
OFF
CAMERA SETUP
OFF
CONFIGURATION
OFF
EXTERNAL DEVICE
OFF
CHANGE FACTORY DEFAULT
LOAD SETUP
SAVE SETUP
DEFAULT
. When done, select <cHaNGe FactOry DeFault>.
You will see a message of “cHaNGe FactOry
DeFault success” on the screen.
The factory default is changed successfully.
` It takes 5 to10 seconds, depending on the USB device.
ESC
FACTORY DEFAULT
ALL
OFF
------------------------------------------------DISPLAY SETUP
OFF
RECORD SETUP
OFF
SCHEDULE SETUP
OFF
CAMERA SETUP
OFF
CONFIGURATION
OFF
EXTERNAL DEVICE
OFF
CHANGE FACTORY DEFAULT
LOAD SETUP
SAVE SETUP
DEFAULT
ESC
English _
00000A_SHR-3040_ENG.indb 45
2009-06-10 오후 3:39:28
setup
load setup
1. Connect the USB device where your settings are saved.
. Select <lOaD setuP>.
The DVR settings will be changed to your settings with a
message of “lOaD setuP success” on the screen.
` It takes 5 to 10 seconds, depending on the USB device. This will
change the DVR settings, not the factory default.
FACTORY DEFAULT
ALL
OFF
------------------------------------------------DISPLAY SETUP
OFF
RECORD SETUP
OFF
SCHEDULE SETUP
OFF
CAMERA SETUP
OFF
CONFIGURATION
OFF
EXTERNAL DEVICE
OFF
CHANGE FACTORY DEFAULT
LOAD SETUP
SAVE SETUP
DEFAULT
ESC
laNGuaGe
You can select a language to your preference.
1. Use the up/down ($%) button to select a language.
The selected language will be applied immediately.
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
ENGLISH
SHUTDOWN
EXIT
_ setup
00000A_SHR-3040_ENG.indb 46
2009-06-10 오후 3:39:30
Network Connection and Settings
Network settings differ depending on the connection mode, so check your network connection mode before
proceeding.
Connection
If connecting to a local network using a router
! setup
1. Launch the Internet browser.
. Provide an IP address in the address bar.
Ex) IP Address: 192.168.1.200  http://192.168.1.200
If the HTTP port is other than 80
1. Launch the Internet browser.
. Provide an IP address and HTTP port number of the DVR in the address bar.
Ex) IP Address: 192.168.1.200: Port Number (1000)  http://192.168.1.200:10000
Connecting via URL
1. Launch the Internet browser.
. Provide a DDNS URL of the DVR in the address bar.
Ex) 6 digits from the end of the MAC address:
<00:00:f0>  g + 0000f0 + websamsung.net = g0000f0.websamsung.net
Connecting via URL - If the HTTP port is other than 80
1. Launch the Internet Browser.
. Provide a DDNS URL and HTTP port number of the camera in the address bar.
Ex) IP Address: http://g0000f0.websamsung.net: Port Number (10000) 
http://g000f0.websamsung.net:10000
English _47
00000A_SHR-3040_ENG.indb 47
2009-06-10 오후 3:39:30
setup
if you are not using a router for network connection
static iP mode
You can establish a direct connection, or connect DVR and remote users in a LAN environment.
Network
1. Set <DHcP mODe> to <maNual> in “maiN meNu >
eXterNal Device > tcP/iP setuP > iP setuP”.
` For information about the IP, gateway, and subnet mask, consult
your network administrator.
SHR-3040
IP SETUP
MAC ADDRESS
DHCP MODE
IP PORT
IP ADDRESS
GATEWAY
SUBNET
00-0A-A2-08-08-F3
MANUAL
IP DETECT
50000
192.168.000.200
192.168.000.001
255.255.255.000
BANDWIDTH
WEB SERVER PORT
1Mbps
00080
OK
ESC
Dynamic iP (DHcP) mode
You can connect the DVR directly to the cable modem, or directly to the optical LAN.
1. Set <DHcP mODe> to <autO> in “maiN meNu > eXterNal Device > tcP/iP setuP >
iP setuP”.
J
` If authentication is required to connect to the broadband network separately, it is recommended to use a router.
_ setup
00000A_SHR-3040_ENG.indb 48
2009-06-10 오후 3:39:31
if using a router
Check the followings to prevent a possible conflict with the static IP of the DVR.
Network
IP Router
LAN
DSL Modem
LAN
! setuP
SHR-3040
using Dvr static iP
Internet Connection : You can connect the DVR to a ADSL/Cable modem-based IP router, or to the IP router
in the LAN environment.
Dvr Network
1. Set <DHcP mODe> to <maNual> in “maiN meNu >
eXterNal Device > tcP/iP setuP > iP setuP”.
. Check if the IP is a static IP provided by the router.
` For information about the IP, gateway, and subnet mask, contact
your network administrator.
M
` If the start (192.168.0.100) and end address
IP SETUP
MAC ADDRESS
DHCP MODE
IP PORT
IP ADDRESS
GATEWAY
SUBNET
BANDWIDTH
WEB SERVER PORT
(192.168.0.200) of the DHCP server are already
specified, provide other addresses (192.168.0.201~192.
168.0.524).
Check if the settings of the gateway and subnet mask match those of the IP router.
00-0A-A2-08-08-F3
MANUAL
IP DETECT
50000
192.168.000.200
192.168.000.001
255.255.255.000
1Mbps
00080
OK
ESC
router DHcP iP address
1. To access the IP router menu, provide the router address in the address bar of the Internet browser from a
local PC in connection with the IP router.(ex: http://192.168.1.1)
. Then, specify the network settings of the local PC as follows:
` Ex) IP: 192.168.1.2
Subnet mask: 255.255.255.0
Gateway: 192.168.1.1
. Use the address to connect to the IP router and open the setup page.
Access the DHCP setup menu of the IP router where you can select the DHCP server mode and specify
the start and end address.
Provide the start (192.168.0.100) and end (192.168.0.200) address, respectively.
` The network settings may differ depending on the IP router.
English _
00000A_SHR-3040_ENG.indb 49
2009-06-10 오후 3:39:32
setup
Port Forwarding with IP/Port Router
1. Enter the port forwarding setup menu of the router you use.
. Port range for external use: Enter the IP port range specified in “MAIN MENU > EXTERNAL DEVICE >
TCP/IP SETUP > IP SETUP” of the connected DVR.
` The IP / port can differ if multiple DVRs are connected to the router.
. Internal PC IP Address: Enter the IP address specified in “MAIN MENU > EXTERNAL DEVICE > TCP/IP
SETUP > IP SETUP” of the connected DVR.
. The internal port range should match “EXTERNAL PORT RANGE”.
Port Forwarding of Web Server Port Router
1. Enter the port forwarding setup menu of the router you use.
. Port range for external use: Enter the web server port range specified in “MAIN MENU > EXTERNAL
DEVICE > TCP/IP SETUP > IP SETUP” of the connected DVR.
` The web server port range can differ if multiple DVRs are connected to the router.
. Internal PC IP Address: Enter the IP address specified in “MAIN MENU > EXTERNAL DEVICE > TCP/IP
SETUP > IP SETUP” of the connected DVR.
. Port range for internal use: The internal port range should match “EXTERNAL PORT RANGE”.
` The network settings may differ, depending on the router model.
To connect to the DVR from outside, you must have set port forwarding for each of the IP port and web server port.
Then, the IP port should be different from the web server port.
M
` You can use DMZ to facilitate your setting. (If only one DVR is connected to the router) If you access the DMZ
setup menu of the router and enter the IP address specified in “MAIN MENU > EXTERNAL DEVICE > TCP/IP
SETUP > IP SETUP” of the connected DVR, no separate port forwarding setting is necessary as all IP ports (IP
port and web server port) of the DVR will be Open.
50_ setup
00000A_SHR-3040_ENG.indb 50
2009-06-10 오후 3:39:32
web viewer
wHat is weB viewer?
Web Viewer enables you to connect to the DVR remotely and transfer live video, play and backup recording data,
and configure settings remotely.
! weB viewer
system requirements
The minimum hardware / operating system requirements to operate the Web Viewer are as below:
~ CPU: Pentium 4 / 3GHz or faster (hyper-threading supported)
~ RAM: 1 GB or more
cONNectiNG tO tHe weB viewer
1. Open the web browser and enter the IP address or URL of
the DVR in the address bar.
` The address setting may differ, depending on the network
connection mode.
. Click <install activeX control…>.
. In the Security Alert popup, select <install>.
. When done, you will see the start screen of the Web
Viewer.
English _1
00000A_SHR-3040_ENG.indb 51
2009-06-10 오후 3:39:34
web viewer
weB viewer at a GlaNce
1
Item
Description
CLIENT SETUP
Allows you to add/edit information necessary for network connection of the Web Viewer.
REMOTE SETUP
Enables you to configure some settings of the DVR from a remote PC.
BACKUP
Copies video data of the DVR to the PC.
PLAYER
Opens and plays backup data in a remote PC.
REMOTE VIEWER
You can view the Live screen of the currently connected DVR.
SEARCH
You can select and play video data of the DVR.
_ web viewer
00000A_SHR-3040_ENG.indb 52
2009-06-10 오후 3:39:36
clieNt setuP
Allows you to add/edit information necessary for network connection of the Web Viewer.
web viewer setup
to register a web site
! weB viewer
1. Click <clieNt setuP>.
. Click <reGisteriNG site>.
The “clieNt setuP” screen appears.
. Provide information about the site to register.
~ ADDRESS: Enter the IP address that you specified in
the DVR.
~ PORT: Enter the port number that you specified in the
DVR.
~ LOCATION: Enter the location name that is registered
with the server.
~ USER ID/PASSWORD: Enter the user ID and password
that you specified in the DVR.
. Click <OK>.
A list of registered sites will be displayed.
update
Click <uPDate> if you want to change information of a REGISTERED SITE.
Others
~ DELETE: You can delete a site in the REGISTERED SITE list.
~ OK: You can select and connect to a site in the registered site list.
~ CANCEL: Cancels your settings in CLIENT SETUP.
English _
00000A_SHR-3040_ENG.indb 53
2009-06-10 오후 3:39:37
web viewer
remOte setuP
You can configure some settings of a remotely connected DVR.
1. Click <remOte setuP>.
. Select <maNual> and provide a value for <aDDress>,
<POrt NumBer>, and <iD> respectively.
` Information of the DVR with the first connected address will be
displayed.
` The “admin” account alone is enabled to access.
. Enter the <PasswOrD> and click <cONNect>.
Your PC will be connected to the DVR remotely.
` The network icon on the DVR screen will switch to display the connection status.
. Select a desired item from <cONFiGuratiON>, <recOrD> and <eXterNal> in the left.
. When done, click <DiscONNect>.
The current DVR will be disconnected.
. To return to the Web Viewer screen, click <clOse>.
alarm setup
You can set the alarm input system and duration for the
channel.
Refer to “alarm setuP”. (Page 32)
Buzzer
You can set the use of the buzzer sound during DVR
operation.
Refer to “BuZZer setuP”. (Page 35)
_ web viewer
00000A_SHR-3040_ENG.indb 54
2009-06-10 오후 3:39:39
interval setup
You can set the sequence screen time, or event record time.
Refer to “iNterval setuP”. (Page 33)
! weB viewer
record configuration
You can set the recording quality.
Refer to “recOrD setuP”. (Page 28)
record schedule
You can set the recording schedule.
Refer to “scHeDule setuP”. (Page 29)
English _
00000A_SHR-3040_ENG.indb 55
2009-06-10 오후 3:39:40
web viewer
BacKuP
1. Enter each necessary item and provide the <user
PasswOrD>.
. Click <cONNect test>.
When your configuration passes the test, you will see a message
of “success connect test!” On the <messaGe> box.
. Click <lOcK> and then select <set BacKuP time>.
The “BacKuP iNFOrmatiON” window appears.
. Click <BrOwse> to specify the <save File PatH>.
. Specify the max storage size, and the start and end time.
. Click <aPPly>.
You can check that a backup file is created in the specified path.
. Click <start BacKuP>.
The button will switch to <stOP BacKuP> with a backup file in
the specified path.
` The backup format is AM4.
You can play and edit the backup file using the “Player”.
J
` Backup is available with the “admin” and “manager” account.
Player
You can play a file that is backed up on your PC.
1. Click <Player>.
The “Player” window appears.
. Click <OPeN> and select a desired backup file.
The selected backup file starts being played.
_ web viewer
00000A_SHR-3040_ENG.indb 56
2009-06-10 오후 3:39:42
Player at a Glance
! weB viewer
Item
Description
System Time
Displays the system time.
Status Pane
Displays the backup start and end date/time with the operation status.
SCREEN DIVISION
You can select full screen or 4-split mode.
CHANNEL
The selected channel will be displayed in Single screen mode.
OPEN FILE
Select a backup file.(AM4 format)
EDIT
AVI SAVE
In this mode, you can save a recording image and make a printout.
This mode is available only if a single channel is selected.
Saves a video in the format of AVI.
This feature is available only if a single channel is selected.
DELAY
Adjust the player interval. The higher the value is, the slower the video plays.
AUDIO
Set the audio sound to On/Off.
[ : Moves the slide bar to the initial point and displays the start image.
( : Fast plays backward.
_ : Plays backward.
Operation Buttons
# : Stops playing temporarily.
+ : Plays forward.
) : Fast plays forward.
] : Moves the slide bar to the end point and displays the end image.
Slide Bar
You can search for a desired image using the slide bar.
Power
Exits the backup player.
English _
00000A_SHR-3040_ENG.indb 57
2009-06-10 오후 3:39:44
web viewer
image eDit
1. Click <OPeN> and select a backup file to play.
. Switch to Single Screen mode and click <eDit>.
The “eDit tOOl” window appears.
. When done, click <eDit>.
Switch to backup play mode.
EDIT TOOL
Contrast
Brightness
Sharpness
Blur
Return
Capture
Print
Adjust a bright area to brighter, and a dark area to darker.
Adjust the contrast to a low level to reduce the brightness.
Adjust the image to a bright level.
Adjust the image to a dark level.
Sharpens the borders.
Makes the image look soft.
Restores your video settings to the original.
Saves the image in the JPEG format.
The image will be saved in the installation directory of the backup player.
Prints out the image.
_ web viewer
00000A_SHR-3040_ENG.indb 58
2009-06-10 오후 3:39:45
avi save
1. Click <avi save>.
The “OPtiON” window appears.
. Set the options to your preference.
~ CHANNEL: Select a channel to save.
~ FRAMERATE: Set the frame rate for a video to save.
! weB viewer
~ SIZE: Set the size of a video to save. The size will be set
automatically according to the video.
. Click <start>.
Starts saving the video from the current point.
. To stop saving, click <stOP>.
Exits saving the video.
When done, the ‘c: weB_BacKuP’ folder will open.
M
` The width and height of a captured or AVI video comply with ‘frame rate’ and ‘frame height’ of the recording
video; however, it will be printed out in 640X480 regardless of the frame size (width and height).
Audio signal will not be saved with AVI SAVE.
remOte viewer
1. Click <remOte viewer>.
The “remOte viewer” window appears.
. Enter the <Pw> and click <cONNect>.
When it is connected successfully, the Live screen will be
displayed.
English _
00000A_SHR-3040_ENG.indb 59
2009-06-10 오후 3:39:47
web viewer
remote viewer at a Glance
Item
Description
DVR Connection
Information
Provide information required to connect to the network.
System Information
Displays information about DVR connection and system operation.
SCREEN DIVISION
You can select Single screen or 4-split mode.
CHANNEL
The selected channel will be displayed in one of the 4 split screens.
You can control a remote PTZ camera that is connected to the DVR.
PTZ Control
` To control a remote PTZ camera, ensure that you have completed PTZ settings in
the DVR.
Network Connection
You can configure settings for network connection and operation.
0_ web viewer
00000A_SHR-3040_ENG.indb 60
2009-06-10 오후 3:39:49
setuP
Click <setuP> to display the Network Setup window.
You must adjust the transfer settings according to the network
environment.
~ Quality: You can set the recording quality.
` For more information, refer to “RECORD > RECORD SETUP”.
(page 28)
! weB viewer
~ Frame Rate: Set the frame rate per second for a video.
` For more information, refer to “RECORD > RECORD SETUP”.
(page 28)
~ Baudrate: You must set the upload speed according to the
network environment of the current DVR.
~ Read: Loads the settings of the connected DVR into the Web Viewer.
~ Write: Saves the Web Viewer settings in the DVR.
M
` If the network setup of Remote Viewer is changed, the record setup will be changed accordingly.
J
` Only the “admin” user account can access the “SETUP” menu.
As Remote Viewer uses a single codec with no separate codec for the network service, a change to the frame
rate and quality via the network will change the recording frame rate and quality accordingly.
English _1
00000A_SHR-3040_ENG.indb 61
2009-06-10 오후 3:39:50
web viewer
searcH
1. Click <searcH>.
The “searcH” window appears.
. Enter the <Pw> and click <cONNect>.
Ensure that you have provided <iP>, <POrt> and <iD>.
. Specify the start time in the <searcH time> bar.
` If you do not specify the start time, the viewer starts playing from the
last run point.
. Click Play (+).
` For more information about the play bar, refer to “Player at a Glance >
Operation Buttons”. (Page 57)
eveNt
You can check information about DVR events such as sensor
detection, motion detection and video loss.
Click <eveNt> in the lower left corner.
The “eveNt list” window appears.
setuP
You can set the network speed.
Click <setuP> in the lower left corner.
The “setuP” dialog appears.
J
` Only the “admin” user account can access the “SETUP”
menu.
_ web viewer
00000A_SHR-3040_ENG.indb 62
2009-06-10 오후 3:39:52
appendix
Product Specification
Item
Details
Multi language Support English, German, French, Spanish, Italian,
Russian, Portuguese, Japanese etc.
Event Log
•
OS
-
Resolution
CIF (NTSC : 352x240 / PAL : 352x288)
Live/Record Rate
NTSC 120/120 ips (PAL 100/100 ips)
Codec
H.264 (Hardware Codec)
HDD
320G(Basic)/500G/750G(SATA)
Built In HDD Capacity
1 Slot
Daylight Saving
•
RS-485
•
Video
4
Audio In/Out
1/1
Mouse I/F
• (Only PS2)
Play back
Speed
Fast, Fastest
Recording
Schedule(Time/Motion/Alarm)
•
Alarm
•
Alarm Input
4
Alarm Output
1 (Relay Out. Selectable NC/NO)
Motion/Video loss
•
Time/Date
•
Percentage of HDD/Event
•
USB
1 (Relay Out. Selectable NC/NO)
System
Event Rec
Search
Back up
Format
! appendix
Language
*AM4 (Include Player)
*AVI format Does Not support
English _63
00000A_SHR-3040_ENG.indb 63
2009-06-10 오후 3:39:52
appendix
Item
Details
Simultaneous Network Connection
4
Netework Spec
Cable Modem, Lan
Network (TCP)
•
Web viewer / BACK UP
•
Web viewer port Set up
• (Remote Setup)
Web viewer P/T/Z Control
•
DDNS
•
Firmware update
• (USB)
Camera
P/T/Z Device
•
Monitor
Dual Output (VGA/BNC)
•
Composite/Spot
• (BNC 1EA)
VGA
• 800x600 (60Hz) 1024x768 (60Hz) 1280x1024 (60Hz)
Network
Video Out
Dimension
371(W) x 62(H) x 247(D) mm
PC Requirements
WebViewer
CPU : Pentium 4 / 3.0Ghz or higher
RAM : 1G
Windows XP (Pro)
Operating Systems
Windows 2000 (Pro)
Windows Vista (Home Basic/Premium)
Operating Temperature
0°C ~ 40°C (32°F ~ 104°F)
Storage Temperature
-20°C ~ +60°C (-4°F ~ +140°F)
Operating Humidity
20% to 85% RH
Storage Humidity
20% to 85% RH
Dimension (W x H x D)
371 x 62 x 247 mm (14.61 x 2.44 x 9.72 inch)
Weight
2.44Kg
64_ appendix
00000A_SHR-3040_ENG.indb 64
2009-06-10 오후 3:39:52
Appearance & Dimension
! appendix
258
247
371
2
61
63
English _65
00000A_SHR-3040_ENG.indb 65
2009-06-10 오후 3:40:01
appendix
Troubleshooting (FAQ)
Problems and Symptoms
Measure
Power does not turn on.
 Only use a power adapter specified in the user manual.
 Fully insert the adaptor’s power jack into the DVR’s power receptacle.
 It sounds a beep when the power is properly supplied, check the output and LED
indicator.
 If the problem persists after these actions, replace the main board as this is an
error from the power system.
LED indicator does not operate.
 Open the DVR case and properly connect the key cable connector.
Fan does not operate.
 Check the power is turned on.
 Connect the fan’s power cable properly to the DVR’s 12V power connector.
 Remove any foreign substances on or around the cable.
 If the problem persists after these actions, the fan or DVR is not in normal
operation. Replace the fan.
DVR produces noise.
 Remove any foreign substances in the fan unit and operate again.
 If the fan produces noise itself, its internal bearings are broken; replace the fan.
 If the problem persists after these actions, check the HDD and replace it if
necessary.
No output displayed on the LCD or no output
on RCA Video out.
 Check the power is turned on.
 Check the camera.
 Turn on the DVR's monitor On/Off switch.
 Connect to RCA Video Out properly.
 Check whether the connecting cable is cut inside.
Check the cable by connecting camera and monitor directly.
Replace the cable if required.
HDD is not recognized properly.
 Check the power is turned on.
 Check the power and data cables are connected to the HDD properly and restart.
 If the problem persists after these actions, replace the HDD.
 Replace the main board if it has a problem with the power system or the bus
line.
It does not record.
 Check the HDD.
 Check the cable, camera and incoming BNC cable for connection.
 Set the HDD OVERWRITE option to <ENABLE> and check its storing operation
again.
 Set the recording type in the Schedule setup and try again.
(ALARM and MOTION modes only records on an event.)
It does not play back.
 Initialize the DVR using FACTORY DEFAULT, and delete files in HDD using CLEAR
PROCESSING, and then check playback after letting the DVR record for a while.
 Try several times of HDD recording and deleting, and replace the HDD if the
problem continues.
 Check the HDD power and data cables.
66_ appendix
00000A_SHR-3040_ENG.indb 66
2009-06-10 오후 3:40:07
Problems and Symptoms
Measure
 Fully insert the USB connector and check its connection.
 Check the USB memory works fine with a PC.
 Check whether it is recognized normally and shows remaining space properly.
 SHR-3040 supports USB1.1 and its writing speed may be slow. Consider its
writing speed when you schedule the backup.
 Check whether actual data has been recorded between the start and end time.
Alarm and Relay do not operate normally.
 Check whether the ALARM is set to Disabled. ALARM is not recognized if it is set
to Disabled.
 Check whether the cable connections are proper and operate again.
 Check whether the external devices are normal, and replace if required.
PTZ does not operate normally.
 Check whether the PTZ controls are supported by the device. Check if the power
satisfies specified power requirements.
 Connect RS-485 (+) and (-) cables to RS-485 port properly.
 Set proper protocol, ID and baud rate both on the Camera and DVR.
 Check connecting cables and replace if required.
Mouse does not operate.
 Check whether the mouse is properly connected to the DVR, and operate again.
 Replace the mouse with a new PS/2 type mouse, and check its operation.
 Using PS/2 gender for USB mouse may not work properly with the DVR. (Mouse
Characteristics)
 If disconnected while in operation, mouse is not recognized properly.
(Same as in PC environment – case of PS/2 type mouse)
 Check the mouse operation on a mouse pad of less reflective.
 If the mouse’s sensitivity is too low, cursor movement may not be natural.
No AUDIO output signal.
 Check audio output after setting the AUDIO output to the correct channel in
AUDIO SETUP.
 Check the camera by replacing it with another one; replace if required.
 Connect to RCA Video Out properly.
 Check whether the Audio I/O volume is set too low; adjust the volume at your
preference.
 Check whether the speakers are powered properly before turning on.
Remote control does not operate.
 Avoid other radio devices since the remote control may have frequency
interference.
 Check whether there is single remote control.
 Replace the batteries of remote control and try again.
 Gently wipe the remote control’s forehead and DVR’s remote reception using a
dry cloth and check operation.
 If the remote control works, then the DVR’s remote reception part is out of order.
If the remote control does not work, replace the remote control.
No TCP/IP connection is established.
 Check and properly connect the network cable between the PC and DVR.
(Check network cable separately.)
 Use a cross-cable for direct connection to a PC, and use a direct cable for HUB /
Router connection.
 Check network operation, cable condition, and assembly of the DVR’s network
board.
 Check whether the network is configured to allow accesses.
 Check IP address, port number and password are properly entered.
 Enter the DVR’s password when accessing.
 Check whether the cables are okay using a PC and replace it if required.
! appendix
It does not backup.
English _67
00000A_SHR-3040_ENG.indb 67
2009-06-10 오후 3:40:08
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from
other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where
and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be
mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return
system.
00000A_SHR-3040_ENG.indb 68
2009-06-10 오후 3:40:08