Sharp LC-20B1U Operating instructions

20B1UCover 02.02.08
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
U
EN
M
Printed on post-consumer recycled paper.
Imprimé sur du papier recyclé.
Impreso en papel reciclado.
Impresso em papel reciclado pós utilização.
Printed in Japan
Imprimé au Japon
Impreso en Japón
Impresso no Japão
TINS-A109WJZZ
02P04-JKK
ESPAÑOL
PORTUGUÊS
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR À CRISTAUX
LIQUIDES
TELEVISOR DE CRISTAL
LÍQUIDO
TELEVISOR DE CRISTAL
LÍQUIDO
FRANÇAIS
ENGLISH
LC-20B1U
LC-20B1U
ENGLISH
LC-20B1U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT INFORMATION
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
LC-20B1U-GBpp01-18
1
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a
triangle is intended to alert the
user to the presence of important operating and maintenance
(servicing) instructions in the
literature accompanying the
product.
02.2.21, 4:43 PM
IMPORTANT INFORMATION
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40
of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries Alliance:
www.eia.org
IMPORTANT:
To aid reporting in case of loss or theft, please
record the TV’s model and serial numbers in the
space provided. The numbers are located at the
rear of the TV.
Model No.:
Serial No.:
U.S.A. ONLY
2
LC-20B1U-GBpp01-18
2
02.2.21, 4:43 PM
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp LCD Color TV product. To ensure safety and
many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product.
IMPORTANT SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property
damage if improperly handled. This product has been engineered and manufactured with the highest
priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent
potential danger, please observe the following instructions when installing, operating and cleaning the
product. To ensure your safety and prolong the service life of your LCD color TV product, please read
the following precautions carefully before using the product.
■ Read instructions—All operating instructions must be read and understood before the product is
operated.
■ Keep this manual in a safe place—These safety and operating instructions must be kept in a
safe place for future reference.
■ Observe warnings—All warnings on the product and in the instructions must be observed
closely.
■ Follow instructions—All operating instructions must be followed.
■ Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.
■ Power source—This product must operate on a power source specified on the specification
label. If you are not sure of the type of power supply used in your home, consult your dealer or
local power company. For units designed to operate on batteries or another power source, refer
to the operating instructions.
■ Power cord protection—The power cords must be routed properly to prevent people from
stepping on them or objects from resting on them. Check the cords at the plugs and product.
■ If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from a
SHARP service center or your dealer.
■ Overloading—Do not overload AC outlets or extension cords.
Overloading can cause fire or electric shock.
■ Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or
short internal parts. For the same reason, do not spill water or liquid on the product.
■ Servicing—Do not attempt to service the product yourself. Removing covers can expose you to
high voltage and other dangerous conditions. Request a qualified service person to perform
servicing.
■ Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and
request a qualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper
adjustment of controls not described in the instructions can cause damage, which often
requires extensive adjustment work by a qualified technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product
indicates that the product needs servicing.
■ Replacement parts—In case the product needs replacement parts, make sure that the service
person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric
shock and/or other danger.
■ Safety checks—Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product is in proper operating condition.
■ Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the
product according to the method recommended by the manufacturer.
■ Polarization—This AC adapter may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
3
LC-20B1U-GBpp01-18
3
02.2.21, 4:43 PM
IMPORTANT SAFETY PRECAUTIONS (Continued)
■ Cleaning—Unplug the power cord from the AC outlet before
cleaning the product. Use a damp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.
■ Water and moisture—Do not use the product near water,
such as bathtub, washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
■ Stand—Do not place the product on an unstable cart, stand,
tripod or table. Placing the product on an unstable base can
cause the product to fall, resulting in serious personal
injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product
on a wall, be sure to follow the manufacturer’s instructions.
Use only the mounting hardware recommended by the
manufacturer.
■ When relocating the product placed on a cart, it must be
moved with utmost care. Sudden stops, excessive force and
uneven floor surface can cause the product to fall from the
cart.
■ Ventilation—The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar surface,
since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in
an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s instructions are followed.
■ The LCD panel used in this product is made of glass.
Therefore, it can break when the product is dropped or
applied with impact. Be careful not to be injured by broken
glass pieces in case the LCD panel breaks.
■ Heat sources—Keep the product away from heat sources
such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
■ The LCD panel is a very high technology product with 921,600 thin film transistors, giving you fine
picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your product.
4
LC-20B1U-GBpp01-18
4
02.2.21, 4:44 PM
IMPORTANT SAFETY PRECAUTIONS (Continued)
■ If an outside antenna is connected to the television equipment, be sure the antenna system is
grounded so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code provides information with respect to proper grounding
of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, Iocation of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC—NATIONAL ELECTRICAL CODE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
■ For added protection for this television equipment during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the
equipment due to lightning and power-line surges.
■ An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.
5
LC-20B1U-GBpp01-18
5
02.2.21, 4:44 PM
CONTENTS
Page
DEAR SHARP CUSTOMER ............................................................................................................. 3
IMPORTANT SAFETY PRECAUTIONS ....................................................................................... 3-5
SUPPLIED ACCESSORIES ............................................................................................................. 7
PREPARATION ............................................................................................................................ 8-10
Using the Remote Control ......................................................................................................... 8
Batteries for the Remote Control .............................................................................................. 8
Power Connection ...................................................................................................................... 9
Antenna Connection ............................................................................................................. 9, 10
FRONT AND REAR CONTROL OPTIONS ............................................................................. 11-13
Removing the Back Cover ....................................................................................................... 13
Listening with Headphones ..................................................................................................... 13
REMOTE CONTROL ...................................................................................................................... 14
BASIC OPERATION ................................................................................................................. 14-17
Turning on POWER ................................................................................................................... 15
Switching TV/VIDEO [AV1/AV2/COMPONENT/CARD/TV] Modes ........................................ 15
Sound Volume ........................................................................................................................... 16
ON/OFF Standby ....................................................................................................................... 16
Changing the Channels ............................................................................................................ 17
SELECTING MENU ITEMS ............................................................................................................ 18
ADJUSTMENT .......................................................................................................................... 19-35
Adjusting the SLEEP TIMER Settings .................................................................................... 19
Adjusting the BRIGHTNESS Settings ..................................................................................... 20
Adjusting the LANGUAGE Settings ........................................................................................ 21
Adjusting the VIDEO ADJUST Settings ........................................................................... 22, 23
Adjusting the PRESET Settings .............................................................................................. 24
SET UP .................................................................................................................................25, 26
Adjusting the BLUE SCREEN Settings .................................................................................. 27
Adjusting the CLOSED CAPTION Settings ............................................................................ 28
Adjusting the V-CHIP Settings .......................................................................................... 29-35
MEMORY CARD PLAYBACK ...................................................................................................36-41
Memory Cards ........................................................................................................................... 36
Card Precautions ...................................................................................................................... 37
Preparation ................................................................................................................................ 38
Pulling out the memory card ................................................................................................... 38
Turning on CARD Mode ........................................................................................................... 39
Selecting the Playback Mode ............................................................................................ 40, 41
CARD ADJUSTMENT ............................................................................................................... 42-47
Selecting CARD SETTING Items ............................................................................................. 42
Adjusting the SLIDE SHOW Settings ..................................................................................... 43
Adjusting the MY PROGRAM Settings ............................................................................. 44, 45
Adjusting the ROTATE Settings ............................................................................................. 46
Adjusting the SOUND Settings ............................................................................................... 47
CONNECTING WITH EXTERNAL DEVICES .......................................................................... 48-50
TROUBLESHOOTING .............................................................................................................. 51-53
SPECIFICATIONS ........................................................................................................................... 54
DIMENSIONAL DRAWINGS .......................................................................................................... 55
6
LC-20B1U-GBpp01-18
6
02.2.21, 4:44 PM
SUPPLIED ACCESSORIES
Make sure the following accessories are provided with the product.
Remote Control
“AAA” size (UM/SUM-4) Dry Battery (×2)
RRMCGA051WJSA
UBATU0038CEZZ
AC Cord
Antenna Cable
RRMCG1559CESA
QCNWG0003CEPA
Operation Manual
Cable Clamp (×2)
ESPAÑOL
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR À CRISTAUX
LIQUIDES
TELEVISOR DE CRISTAL
LÍQUIDO
TELEVISOR DE CRISTAL
LÍQUIDO
PORTUGUÊS
LC-20B1U
FRANÇAIS
ENGLISH
AC Adapter
QACCD3097CEPA
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
MENU
UADP-0243CEPZ
UADP-0212CEZZ
TINS-A109WJZZ
UBATU0026GEZZ
LHLDW0109CESA
LHLDW1028GEZZ
7
LC-20B1U-GBpp01-18
7
02.2.21, 4:44 PM
PREPARATION
Using the Remote Control
■ Use the remote control by pointing it towards the remote sensor window.
Objects between the remote control and sensor window may prevent
proper operation.
Cautions regarding use of remote control
■ Do not expose the remote control to shock.
In addition, do not expose the remote control to liquids, and do not place
in an area with high humidity.
■ Do not install or place the remote control under direct sunlight. The heat
may cause deformation of the unit.
■ The remote control may not work properly if the remote sensor window
of the main unit is under direct sunlight or strong lighting. In such a
case, change the angle of the lighting or LCD TV set, or operate the
remote control closer to the remote sensor window.
Batteries for the Remote Control
If the remote control fails to operate the LCD color TV functions, replace the batteries in the remote
control.
1
2
Open the battery
cover.
Insert batteries (two “AAA”
(UM/SUM-4) size batteries,
supplied with product).
3
Close the battery
cover.
ー
+
+
ー
■ Slide the cover while
pressing down.
■ Place the batteries with their
terminals corresponding to
the (+) and (–) indications in
the battery compartment.
Caution!
Cautions regarding batteries
Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the
instructions below.
• Place batteries with their terminals corresponding to the (+) and (–) indications.
• Different types of batteries have different characteristics. Do not mix batteries of different types.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new
batteries and/or cause old batteries to leak chemicals.
• Remove batteries when they become weak.
Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a
cloth.
• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
• If the remote control is not used for an extended period of time, remove the batteries from the remote
control.
8
LC-20B1U-GBpp01-18
8
02.2.21, 4:44 PM
PREPARATION (Continued)
Power Connection
CH
MENU TV/VIDEO
MAIN POWER
VOL
Household power outlet
Plug into AC outlet.
AC adapter
AC cord
To DC input terminal
(DC 13V)
Note
●
●
●
Use a commercially available AC plug adapter, if necessary, depending on the design of the wall outlet.
Always turn the main POWER switch of the LCD TV set to off when connecting the AC adapter.
Always unplug the AC adapter from the product and power outlet when not using for a long period of time.
Antenna Connection
CABLE TV (CATV) CONNECTION
• A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75ohm coaxial cable to the set, screw the 75-ohm cable to the ANT. terminal.
• Some cable TV companies offer “premium pay channels”. Since the signals of these premium pay
channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber
by the cable TV company. This converter/descrambler is necessary for normal viewing of the
scrambled channels. (Set your TV to channel 3 or 4, typically one of these channels is used. If this
is unknown, consult your cable TV company.) For more specific instructions on installing cable TV,
consult your cable TV company. One possible method of utilizing the converter/descrambler
provided by your cable TV company is explained below.
Please note: An RF switch provided with two inputs (A and B) is required (not supplied).
“A” position on the RF switch (not supplied) : You can view all unscrambled channels by using the
TV’s channel keys.
“B” position on the RF switch (not supplied) : You can view the scrambled channels via the converter/
descrambler by using the converter’s channel keys.
RF switch (not supplied)
Two-set
signal
splitter
(not
supplied)
OUT
Cable TV Line
IN
Cable TV converter/
descrambler
(not supplied)
Note
●
Consult your SHARP Dealer or Service Center for the type of splitter, RF switch or combiner that might be
required.
9
LC-20B1U-GBpp01-18
9
02.2.21, 4:44 PM
PREPARATION (Continued)
Antenna Connection (Continued)
ANTENNAS
• The antenna requirements for good color television reception are more important than those for black & white
television reception. For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connections that are provided with the various antenna
systems.
F-type connector
1. A 75-ohm system is generally a round cable with F-type
connector that can easily be attached to a terminal without
tools (not supplied).
75-ohm coaxial cable (round)
2. A 300-ohm system is a flat “twin-lead” cable that can be
attached to a 75-ohm terminal through a 300-75-ohm
adapter (not supplied).
300-ohm twin-lead cable (flat)
OUTDOOR ANTENNA CONNECTION
• Use one of the following two diagrams if you connect an outdoor antenna.
A: Using a VHF/UHF combination outdoor antenna.
B: Using separate VHF and/or UHF outdoor antennas.
• Connect the outdoor antenna cable lead-in to the ANT. terminal on the rear of the TV set.
A. Combination VHF/UHF Antenna
300/75-ohm
adapter
(not supplied)
VHF/UHF
antenna
VHF/UHF
antenna
ro
CH
MENU TV/VIDEO
MAIN POW
VOL
300-ohm
twin-lead
75-ohm
coaxial cable
To antenna input
terminal
Antenna cable (supplied)
B. Separate VHF and/or
UHF Antennas
UHF
antenna
VHF
antenna
300-ohm
twin-lead
Combiner
(not supplied)
IN
300-ohm
twin-lead
OUT
75-ohm
coaxial cable
10
LC-20B1U-GBpp01-18
10
02.2.21, 4:44 PM
or
FRONT AND REAR CONTROL OPTIONS
Main unit (front view)
Upper control panel
VOL
MENU TV/VIDEO
CH
MAIN POWER
MAIN POWER
TV/VIDEO
MENU
CH ( )/( )
VOL (–)/(+)
Speaker
Speaker
PC Card slot
POWER
SLEEP
To change the vertical angle of the LCD
TV set, tilt the screen up to 10 degrees
forward or 20 degrees backward. The
TV set can also be rotated 90 degrees
horizontally. Please adjust the angle so
that the TV set can be watched most
comfortably.
SLEEP indicator
The SLEEP indicator lights up red when
the SLEEP TIMER is set to on.
Remote sensor window
(The actual location is not visible.)
POWER indicator
A green indicator lights when the power is
on and a red indicator lights when in the
standby mode (the indicator will not light
when the main power is off).
Note
TV/VIDEO, CH ( )/( ), VOL (–)/(+), and MENU on the main unit have the same functions as the same buttons
on the remote control. Fundamentally, this operation manual provides a description based on operation with the
remote control.
●
11
LC-20B1U-GBpp01-18
11
02.2.21, 4:44 PM
FRONT AND REAR CONTROL OPTIONS (Continued)
Main unit (rear view)
COM
Y
PB
PR
L
AUDIO
R
(L)
(R)
AV-IN2/OUT
COMPONENT
(L)
(R)
MENU TV/VIDEO
L
AUDIO
R
PONENT
VIDEO
AUDIO
AUDIO
Y
PB
PR
AUDIO
AUDIO
CH
VIDEO
OUT
AV-IN2/
MAIN POWER
VOL
VIDEO
AV-IN1
PC Card
PC Card slot
AUDIO (L)
AUDIO (R)
S-VIDEO
HEADPHONE
Antenna terminal
POWER INPUT
(DC 13V)
12
LC-20B1U-GBpp01-18
12
02.2.21, 4:44 PM
VIDEO
AV-IN
1
L
AUDIO
R
S-VID
EO
HEAD
PHON
E
ANT.
POWER
INPUT
DC13V
FRONT AND REAR CONTROL OPTIONS (Continued)
Removing the Back Cover
CH
MENU TV/VIDEO
■ Before connecting a connection cord into the rear
terminal, remove the back cover. Push in the tab and
pull out the back cover carefully.
MAIN POWER
VOL
■ To mount the cover, insert the 2 hooks on the
bottom of the cover into the cabinet and press on
the upper part of the back cover until the tab locks
in place with a click.
Listening with Headphones
■ Plug the headphone mini-plug into the HEADPHONE jack located on the rear of the TV set.
▼ On-screen display
CH
VOL
< Rear terminal
VOLUME
60
Headphones
Note
●
●
Headphones are not included in the supplied accessories.
No sound will be heard from the main unit speakers when a headphone mini-plug is connected into the
HEADPHONE jack.
13
LC-20B1U-GBpp01-18
13
02.2.21, 4:44 PM
REMOTE CONTROL
POWER
POWER
ENTER/
]/[/</>(Cursor control)
DISPLAY
DISPLAY*
1
SLEEP
CARD
CARD*2
SLEEP
ENTER
MUTE
MUTE
BRIGHT
TV/VIDEO
MENU TV/VIDEO
BRIGHT
MENU
FLASHBACK*3
FLASHBACK
VOL
CH
VOL(+)/(–)
CH (
MTS*4
1
2
3
4
5
6
7
8
9
MTS
0
100
)/(
)
Channel Select
*1 Displays the receiving
channel for 10 seconds.
*2 Turns on CARD mode to play
back a memory card.
*3 Returns to the previous
channel.
*4 Selects audio settings.
BASIC OPERATION
This product is factory set to comply with the TV broadcasting system in the United States. For Brazil,
Argentina and Uruguay, set the color system according to the country before using this product by
following the table below.
Country
TV broadcasting
system
Factory setting of color system
User setting
TV
Video
TV/Video
U.S.A.
Color: NTSC
TV ch: US ch
NTSC (N358)
US ch
NTSC (N358)
US ch
Not required
or N/A
Canada, Mexico,
Latin America
Color: NTSC
TV ch: US ch
NTSC (N358)
US ch
NTSC (N358)
US ch
Not required or N/A
Brazil
Color: PAL-M
TV ch: US ch
NTSC (N358)
US ch
NTSC (N358)
US ch
Set color system to
PAL-M (see page 23)
Argentina,
Uruguay
Color: PAL-N
TV ch: US ch
NTSC (N358)
US ch
NTSC (N358)
US ch
Set color system to
PAL-N (see page 23)
Note
●
The 3 Dimensional Y/C separation circuit* only works when the color system is set to N358 in TV mode and Video
mode.
*The 3 Dimensional Y/C separation circuit is used to remove flickering and color bleeding.
14
LC-20B1U-GBpp01-18
14
02.2.21, 4:44 PM
BASIC OPERATION (Continued)
Turning on POWER
1
MAIN POWER
Press MAIN POWER, located on
the upper side of the main unit, to
on.
2
▼ On-screen display
2
The POWER indicator instantaneously changes from red to green
and the main unit is turned on.
Note
●
POWER indicator
The input mode indication disappears
after several seconds.
STEREO < ON A I R
SAP
MONO
Notes:
Switching TV/VIDEO [AV1/AV2/COMPONENT/CARD/TV] Modes
POWER
POWER
1
Turn on the power of the connected
video equipment.
2
Press TV/VIDEO and select the
applicable input source. The screen
displays AV1, AV2, COMPONENT,
CARD or TV mode each time TV/
VIDEO is pressed.
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
AV 1
AV2 mode
MENU TV/VIDEO
AV 2
Note
FLASHBACK
VOL
AV1 mode
CH
TV/VIDEO
1
2
3
4
5
6
7
8
9
MTS
0
100
●
•
•
•
•
The AV input mode indication remains
for 3 seconds.
AV1: Video equipment connected to the
AV1 input terminals.
An S-Video input terminal is
additionally provided for the AV1 COMPONENT mode
input. If both the S-Video terminal
COMPONE N T
and normal video terminals are
connected with cables, the SVideo input terminal takes priority.
AV2: AV2 mode is used to adjust the
preset settings and IN or OUT can
be selected. AV2 indication is not
displayed when OUT is selected.
CARD mode
(For details on setting AV-OUT,
see page 24.)
C ARD
COMPONENT:
Video equipment connected to the
COMPONENT input terminals.
CARD:
Switches to CARD mode.
(For details on CARD mode, see
pages 36-47.)
TV mode
12
15
LC-20B1U-GBpp01-18
15
02.2.21, 4:44 PM
BASIC OPERATION (Continued)
Sound Volume
1
POWER
Press VOL (+) to increase the sound
volume. The segment of the indicator
increases.
VOLUME
50
DISPLAY
SLEEP
CARD
2
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
Press VOL (–) to decrease the sound
volume. The segment of the indicator
decreases.
VOLUME
10
MUTE
VOL
(+)/(–)
To mute the sound
1
Press MUTE to temporarily turn off
the sound.
is displayed for
The MUTE mark
4 seconds.
2
Press MUTE or VOL (+)/(–) to turn
the sound back to the previous level.
The mute function is automatically
turned off when any of the following
buttons are pressed: POWER,
VOL (+)/(–), or MTS.
MTS
VOLUME
30
To select MTS (Multi ch TV Sound)
1
Press MTS to display the MTS
screen.
2
Press MTS to select the MTS
settings.
[STEREO]: stereo audio
[SAP]:
second audio program
[MONO]: monophonic audio
2
STEREO < ON A I R
SAP
MONO
Note
●
<ON AIR appears when a stereo or SAP
broadcast is being aired.
ON/OFF Standby
To turn off the LCD TV
POWER
Press POWER on the remote control.
The POWER indicator will turn red.
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
FLASHBACK
VOL
To turn the LCD TV back on
MENU TV/VIDEO
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
POWER
Press POWER again.
The POWER indicator will turn green.
16
LC-20B1U-GBpp01-18
16
02.2.21, 4:44 PM
BASIC OPERATION (Continued)
Changing the Channels
Changing channels by using Channel Select on the remote control
• This LCD TV set allows you to select up to 125 channels (1 to 125). To select a channel, enter a 2or 3-digit number.
To select a 1- or 2-digit channel
number (e.g., Channel 5):
Complete the following procedure
within 4 seconds.
POWER
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
1
2
MENU TV/VIDEO
FLASHBACK
VOL
CH
Press the
Press the
0–
5
button.
5
button.
Note
1
2
3
4
5
6
7
8
9
MTS
0
100
●
When selecting a 1-digit channel number,
do not fail to press the
button first.
Channel
Select
To select a 3-digit channel number
(e.g., Channel 115):
Complete the following procedure
within 4 seconds.
1
2
3
Press the
button.
Press the
button.
Press the
5
1––
1 1–
1 15
button.
Changing channels with CH ( )/( ) on the remote control
Air
Press CH ( ) and the channels change in the
2 → 3 → . . . → 68 → 69 → 2 → 3 → . . .
Press CH ( ) and the channels change in the
3 → 2 → 69 → 68 → . . . → 3 → 2 → . . .
Cable Press CH ( ) and the channels change in the
1 → 2 → 3 → . . . → 125 →1 → 2 → 3 → . . .
Press CH ( ) and the channels change in the
3 → 2 → 1 → 125 → . . . → 3 → 2 → 1 → . . .
order shown below:
order shown below:
order shown below:
order shown below:
17
LC-20B1U-GBpp01-18
17
02.2.21, 4:44 PM
SELECTING MENU ITEMS
Selecting Menu Items
• This LCD TV set allows you to adjust the various settings using the menu screen. Select the desired
menu item by following the steps below and then refer to the indicated page for details.
POWER
(Page 19)
1
Press MENU to display the MENU
screen.
2
Press ]/[ to select the desired
menu item, and press ENTER.
3
Press MENU to exit.
SLEEP T IMER
RETURN
SLEEP T IMER [ ––– REMA I N ]
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
SELECT :
ENTER :
ENTER
EX I T : MENU
(Pages 22, 23)
V I DEO ADJUST ( TV )
RETURN
P I CTURE
[
30 ]
[
0]
T I NT
[
0]
COLOR
0]
BLACK LEVEL [
SHARPNESS
[
0]
COLOR SYSTEM [ N358 ]
RESET
MENU
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
ENTER :
ENTER
EX I T :
MENU
(Pages 20, 24)
SELECT :
ENTER :
ENTER
EX I T :
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
]
AUTO POWER OFF [ OFF
UPS I DE
[ NORMAL ]
R I GHT / LEF T
[ NORMAL ]
AV2 I N / OUT
[ IN
]
MENU
Note
There are two sets of items displayed
on the MENU screen depending on
whether TV/VIDEO or CARD mode is
selected. To display the MENU
screen for CARD mode, press CARD
to turn on CARD mode and then
press MENU to display the MENU
screen.
● The TINT display only appears when
the color system is set to N358 or
N443.
● The displayed items differ depending
on the setting conditions.
● The selected item changes to yellow.
● Items in magenta cannot be selected.
● This product is factory set to comply
with the color system in the United
States (NTSC-N358). For Brazil
(PAL-M), Argentina (PAL-N) and
Uruguay (PAL-N), set the color
system before using this product.
● To return to the previous screen,
select RETURN.
● You can adjust some settings with the
special buttons: SLEEP and BRIGHT
(see page 19 and page 20).
●
SELECT :
EX I T : MENU
ENTER
EX I T : MENU
CLOSED CAPT I ON
RETURN
]
MODE [ OFF
DATA [ CH 1
]
SELECT :
ENTER :
(Pages 31–35)
I NPUT SECRET NO .
– – – –
EX I T : MENU
(Pages 21, 25–27)
SET UP
RETURN
BLUE SCREEN [ ON ]
LANGUAGE
CH–SETT I NG
* The screen indications shown above are larger than actual for easy reading.
18
18
ENTER
(Page 28)
SELECT :
LC-20B1U-GBpp01-18
ENTER :
02.2.21, 4:44 PM
ENTER :
ENTER
EX I T : MENU
ADJUSTMENT
Adjusting the SLEEP TIMER Settings
You can set the SLEEP TIMER to automatically turn off the TV.
SLEEP
Directly setting the SLEEP TIMER
POWER
1
Press SLEEP to display the SLEEP
TIMER screen.
2
Press SLEEP to set the sleep timer
(in minutes).
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
FLASHBACK
VOL
The time can be set in increments
of 30 minutes and in the range
between 30 and 120 minutes.
MENU TV/VIDEO
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
––– REMA I N
The SLEEP TIMER is turned off
when --- is displayed.
MENU
Note
●
The SLEEP TIMER screen automatically
disappears in 3 seconds.
60 REMA I N
Setting the SLEEP TIMER on the
MENU screen
1
Press MENU to display the MENU
screen.
2
Press ]/[ to move the cursor to
SLEEP TIMER.
3
Press ENTER to display the
SLEEP TIMER screen, and press
ENTER.
4
Press </ > to set the sleep timer
(in minutes) and press ENTER .
The time can be set in increments
of 30 minutes and in the range
between 30 and 120 minutes.
The SLEEP TIMER is turned off
when --- is displayed.
5
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SLEEP T IMER
RETURN
SLEEP T IMER [ ––– REMA I N ]
SELECT :
ENTER :
ENTER
EX I T : MENU
SLEEP T IMER
RETURN
SLEEP T IMER [ 60 REMA I N ]
Press MENU to return to the main
screen.
ADJUST :
ENTER :
ENTER
EX I T : MENU
Note
●
●
●
When you set the SLEEP TIMER, the SLEEP indicator lights.
After you set the SLEEP TIMER, if you turn off the MAIN POWER on the TV set or press the POWER button on
the remote control, the SLEEP TIMER setting is cancelled and the SLEEP indicator goes out.
5 minutes before the SLEEP TIMER turns off the TV, 5 REMAIN is displayed on the screen for 4 seconds. The
SLEEP TIMER counts down and shows a similar 4-second display for each remaining minute until the timer turns
off the TV.
19
LC-20B1U-GBpp19-35
19
02.2.21, 4:42 PM
ADJUSTMENT (Continued)
Adjusting the BRIGHTNESS Settings
You can set the brightness of the screen.
Directly setting the BRIGHTNESS
POWER
DISPLAY
SLEEP
CARD
1
Press BRIGHT to display the
BRIGHTNESS screen.
2
Press BRIGHT to change the
setting.
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
BRIGHT
FLASHBACK
VOL
NORMAL
DARK
CH
BR I GHTNESS [ BR I GHT ]
Note
1
2
3
4
5
6
7
8
9
MTS
0
100
BRIGHT
●
●
The BRIGHTNESS screen automatically
disappears in 3 seconds.
[BRIGHT]: maximum brightness
[NORMAL]: 60% brightness (suitable for
viewing in a well-lit area and saves
energy)
[DARK]: 20% brightness (sufficiently bright
when viewing in a dimly lit area)
Setting the BRIGHTNESS on the
MENU screen
POWER
1
Press MENU to display the MENU
screen.
2
Press ]/[ to move the cursor to
PRESET, and press ENTER.
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
MENU
SELECT :
3
Press ]/[ to move the cursor to
BRIGHTNESS, and press ENTER.
Press </ > to change the setting,
and press ENTER.
5
Press MENU to return to the main
screen.
20
20
EX I T : MENU
ENTER :
ENTER
EX I T : MENU
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
AUTO POWER OFF [ OFF
]
UPS I DE
[ NORMAL ]
R I GHT / LEF T
[ NORMAL ]
AV2 I N / OUT
[ IN
]
ADJUST :
LC-20B1U-GBpp19-35
ENTER
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
AUTO POWER OFF [ OFF
]
UPS I DE
[ NORMAL ]
R I GHT / LEF T
[ NORMAL ]
AV2 I N / OUT
[ IN
]
SELECT :
4
ENTER :
02.2.21, 4:42 PM
ENTER :
ENTER
EX I T : MENU
ADJUSTMENT (Continued)
Adjusting the LANGUAGE Settings
The language for the On-Screen Display can be ENGLISH, SPANISH or FRENCH.
1
Press MENU to display the MENU
screen.
POWER
DISPLAY
SLEEP
CARD
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[
SELECT :
2
Press ]/[ to move the cursor to
SET UP, and press ENTER.
MENU
Press ]/[ to move the cursor to
LANGUAGE, and press ENTER.
Press ]/[ to select the language.
5
Press MENU to return to the main
screen.
EX I T : MENU
ENTER :
ENTER
EX I T : MENU
ENTER
EX I T : MENU
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
SELECT :
4
ENTER
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
3
ENTER :
ENTER :
LANGUAGE
ENGL I SH
ESPAÑOL
FRANCA I S
SELECT :
EX I T : MENU
21
LC-20B1U-GBpp19-35
21
02.2.21, 4:42 PM
ADJUSTMENT (Continued)
Adjusting the VIDEO ADJUST Settings
1
Press MENU to display the MENU
screen.
POWER
DISPLAY
SLEEP
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
SELECT :
2
MENU
Press ]/[ to move the cursor to
VIDEO ADJUST, and press
ENTER.
ENTER :
Press ]/[ to move the cursor to
the desired item, and press
ENTER.
ENTER :
ENTER
EX I T : MENU
V I DEO ADJUST ( TV )
RETURN
P I CTURE
[
30 ]
T I NT
[
0]
COLOR
[
0]
BLACK LEVEL [
0]
SHARPNESS
[
0]
COLOR SYSTEM [ N358 ]
RESET
ENTER :
SELECT :
4
EX I T : MENU
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
3
ENTER
EX I T : MENU
ENTER
Press </ > to change the setting.
Note
●
5
See page 23 for the settings.
Press MENU to return to the main
screen.
RETURN
P I CTURE
30
–
SELECT :
22
LC-20B1U-GBpp19-35
22
02.2.21, 4:42 PM
+
ADJUST :
EX I T : MENU
ADJUSTMENT (Continued)
Adjusting the VIDEO ADJUST Settings (Continued)
TV mode
Selected item
Press <.
Press >.
PICTURE
Decrease contrast
Increase contrast
TINT
Toward purple
Toward green
COLOR
Lower color intensity
Higher color intensity
BLACK LEVEL
Less bright
More bright
SHARPNESS
Soft picture
Sharp picture
Selected item
Press <.
Press >.
PICTURE
Decrease contrast
Increase contrast
TINT
Toward purple
Toward green
COLOR
Lower color intensity
Higher color intensity
BLACK LEVEL
Less bright
More bright
SHARPNESS
Soft picture
Hard picture
RED-BLUE
More red level
More blue level
GREEN
Less green level
More green level
COLOR SYSTEM
Press </ > to select the COLOR SYSTEM.
COLOR SYSTEM
AV mode
■
When the COMPONENT mode is selected
Note
●
●
●
●
TINT is displayed only when N358 or N443 is selected.
In BLUE SCREEN, PICTURE setting displayed in magenta cannot be selected.
Selecting RESET will return all settings to the factory settings.
This product is factory set to comply with the color system in the United States (NTSC-N358). For Brazil (PAL-M),
Argentina (PAL-N) or Uruguay (PAL-N), adjust the color system before using this product.
CARD mode
Selected item
Press <.
Press >.
PICTURE
Decrease contrast
Increase contrast
COLOR SYSTEM
The COLOR SYSTEM is always set to N358 and cannot be changed.
Note
●
It is possible to select PICTURE, RESET, and RETURN on the VIDEO ADJUST screen for CARD mode. All other
items cannot be selected.
23
LC-20B1U-GBpp19-35
23
02.2.21, 4:42 PM
ADJUSTMENT (Continued)
Adjusting the PRESET Settings
POWER
1
Press MENU to display the MENU
screen.
2
Press ]/[ to move the cursor to
PRESET, and press ENTER.
3
Press ]/[ to move the cursor to
the desired item, and press
ENTER.
DISPLAY
SLEEP
CARD
ENTER
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
MENU
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
]
AUTO POWER OFF [ OFF
UPS I DE
[ NORMAL ]
R I GHT / LEF T
[ NORMAL ]
AV2 I N / OUT
[ IN
]
SELECT :
4
Press </ > to change the setting,
and press ENTER.
5
Press MENU to return to the main
screen.
Factory setting
BRIGHTNESS
[BRIGHT]
AUTO POWER OFF
(only TV mode)
[OFF]
Maximum brightness
ENTER :
ENTER
EX I T : MENU
Setting change
[NORMAL] Brightness 60% → Suitable for viewing in a well-lit area.
Saves energy.
[DARK]
Brightness 20% → Sufficiently bright when
viewing in a dimly lit area.
[ON]
[OFF]
[DOWN]
The power of the LCD TV set is turned off when there is
no signal for 5 minutes.
This feature is inactive.
Inverted image → To display images
upside down for special uses.
UPSIDE
[NORMAL] Normal vertical
image orientation
RIGHT/LEFT
[NORMAL] Normal horizontal
image orientation
[MIRROR] Mirror image → To display mirror
images for special uses.
[IN]
[OUT
AV2 IN/OUT
EX I T : MENU
ENTER
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
AUTO POWER OFF [ OFF
]
UPS I DE
[ NORMAL ]
R I GHT / LEF T
[ NORMAL ]
AV2 I N / OUT
[ IN
]
ADJUST :
Selected item
ENTER :
[OUT
ABC
MUTE
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
CBA
] Line Output is selected, Output volume is fixed, Speaker
output is available.
] Line Output is selected, Output volume is variable,
Speaker output is Mute.
Note
●
When OUT has been selected as the AV2 IN/OUT setting, it is not possible to set AV2 to ON in SOUND SETTING
for CARD mode. In order to set AV2 to ON, select IN as the AV2 IN/OUT setting.
24
LC-20B1U-GBpp19-35
24
02.2.21, 4:42 PM
ADJUSTMENT (Continued)
SET UP
■ CHANNEL SETTING
It is necessary to set the receiving mode to AIR or CABLE channels to receive locally broadcast TV
programs.
POWER
1
Press MENU to display the MENU
screen.
2
Press ]/[ to move the cursor to
SET UP, and press ENTER.
DISPLAY
SLEEP
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
CARD
ENTER
MUTE
BRIGHT
FLASHBACK
VOL
SELECT :
MENU TV/VIDEO
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[
3
Press ]/[ to move the cursor to
CH-SETTING, and press ENTER.
MENU
Press ]/[ to move the cursor to
AIR/CABLE, and press ENTER.
Press ]/[ to move the cursor to
the desired mode.
6
Press MENU to return to the main
screen.
EX I T : MENU
ENTER :
ENTER
EX I T : MENU
ENTER :
ENTER
EX I T : MENU
CH–SETT I NG
RETURN
A I R/ CABLE
CH SEARCH
CH MEMORY
SELECT :
5
ENTER
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
SELECT :
4
ENTER :
A I R / CABLE
AIR
CABLE
SELECT :
EX I T : MENU
Note
●
Receivable channels of your TV set are:
AIR channels:
VHF: 2 through 13.
UHF: 14 through 69.
CABLE channels:
1 (HRC and IRC mode only)
2 through 125 (STD, HRC and IRC)
25
LC-20B1U-GBpp19-35
25
02.2.21, 4:42 PM
ADJUSTMENT (Continued)
SET UP (Continued)
■ Saving broadcast TV channels in the memory
1
Press MENU to display the MENU
screen, press ]/[ to move the
cursor to SET UP, and press
ENTER.
2
Press ]/[ to move the cursor to
CH-SETTING, and press ENTER.
3
Press ]/[ to move the cursor to
CH SEARCH, and press ENTER.
4
Press >. The tuner will search
through all available channels in
your area and add them to the
TV’s memory.
POWER
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
ENTER/
]/[/
</ >
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
MENU
CH–SETT I NG
RETURN
A I R/ CABLE
CH SEARCH
CH MEMORY
CH SEARCH
AIR
2
Note
●
To interrupt CH SEARCH, press <. CH
SEARCH will stop at the current
channel and will not add any higher
channels.
5
START :
EX I T : MENU
Press MENU to exit.
■ Adding weak or additional channels or erasing unwanted channels from TV memory
1
Press MENU to display the MENU
screen, press ]/[ to move the
cursor to SET UP, and press
ENTER.
2
Press ]/[ to move the cursor to
CH-SETTING, and press ENTER.
3
Press ]/[ to move the cursor to
CH MEMORY, and press ENTER.
4
Use ]/[ or Channel Select to
select each desired channel to add
or erase.
5
Press > to add the channel to the
TV’s memory or press < to erase
the channel from the TV’s memory.
6
Press MENU to exit.
POWER
DISPLAY
SLEEP
CARD
CH MEMORY
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH–SETT I NG
RETURN
A I R/ CABLE
CH SEARCH
CH MEMORY
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
MENU
Channel
Select
AIR
TO ADD :
EX I T : MENU
>
to add channel 2
to the TV memory
TO ERASE :
Note
:
● If CH SEARCH is performed again, the previously memorized channels will be lost.
26
26
<
to erase channel 2
to the TV memory
CH MEMORY
AIR
LC-20B1U-GBpp19-35
2
02.2.21, 4:42 PM
2
EX I T : MENU
ADJUSTMENT (Continued)
Adjusting the BLUE SCREEN Settings
■ BLUE SCREEN
Automatically turns the screen blue if a broadcast signal is not received.
POWER
1
Press MENU to display the MENU
screen.
2
Press ]/[ to move the cursor to
SET UP, and press ENTER.
DISPLAY
SLEEP
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
CARD
ENTER
MUTE
BRIGHT
FLASHBACK
VOL
SELECT :
MENU TV/VIDEO
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
3
MENU
Press ]/[ to move the cursor
to BLUE SCREEN, and press
ENTER.
ENTER :
ENTER
EX I T : MENU
ENTER
EX I T : MENU
ENTER
EX I T : MENU
SET UP
RETURN
BLUE SCREEN [ ON ]
LANGUAGE
CH–SETT I NG
SELECT :
4
Press </ > to select ON or OFF,
and press ENTER.
5
Press MENU to return to the main
screen.
ENTER :
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
ADJUST :
ENTER :
Note
●
●
●
When received signals are weak or interfered with by some other signals, the BLUE SCREEN function may be
activated. To watch the TV under such conditions, set BLUE SCREEN to OFF.
When the AV-IN1, AV-IN2 or COMPONENT input mode is selected, if no signal is being input, the BLUE SCREEN
function is activated.
The BLUE SCREEN function is inactive in CARD mode.
27
LC-20B1U-GBpp19-35
27
02.2.21, 4:42 PM
ADJUSTMENT (Continued)
Adjusting the CLOSED CAPTION Settings
■ SETTING CLOSED CAPTION
• This TV set is equipped with an internal Closed Caption decoder. “Closed Caption” is
a system which allows conversations, narration, and sound effects in TV programs
and home videos to be viewed as captions on the TV screen (see the illustration).
• Not all the programs and videos will offer closed captioning. Please look for the “ ”
symbol to ensure that captions will be shown.
• The Closed Caption broadcasts can be viewed in two modes: [CAPTION] and
[TEXT]. For each mode, two channels are available: CH1 and CH2.
The [CAPTION] mode shows subscripts of dialogs and commentaries of TV dramas
and news programs while allowing a clear view of the picture.
The [TEXT] mode displays various information over the picture (such as TV program
schedules and weather forecasts, etc.) that is independent of the TV programs.
POWER
DISPLAY
SLEEP
CARD
1
Press MENU to display the MENU
screen.
2
Press ]/[ to move the cursor to
CLOSED CAPTION, and press
ENTER.
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
MENU
SELECT :
3
Press ]/[ to move the cursor to
MODE or DATA, and press ENTER.
Press </ > to change the CLOSED
CAPTION setting, and press ENTER.
5
Press MENU to return to the main
screen.
MODE:
CAPTION
TEXT
OFF
DATA:
ENTER
EX I T : MENU
ENTER
EX I T : MENU
ENTER
EX I T : MENU
CLOSED CAPT I ON
RETURN
]
MODE [ OFF
DATA [ CH 1
]
SELECT :
4
ENTER :
ENTER :
CLOSED CAPT I ON
RETURN
MODE [ CAPT I ON ]
DATA [ CH 1
]
CH 1
CH 2
ADJUST :
ENTER :
Note
●
●
●
●
If a broadcast has CLOSED CAPTION and MUTE is pressed, the set enters [CAPTION] mode automatically. Pressing
MUTE again will return the set to its previous condition.
Closed Caption may malfunction (white blocks, strange characters, etc.) if signal conditions are poor or if there are
problems at the broadcast source. This does not necessarily indicate a problem with your set.
If any button is pressed to call up the On-Screen Display while viewing a Closed Caption broadcast, the closed captions
will disappear momentarily.
If no TEXT broadcast is being received while viewing in the [TEXT] mode, the screen may become dark and blank for
some programs. Should this occur, switch the Closed Caption mode to OFF.
28
LC-20B1U-GBpp19-35
28
02.2.21, 4:42 PM
ADJUSTMENT (Continued)
Adjusting the V-CHIP Settings
■ V-CHIP
• This function allows TV programs to be restricted and TV usage to be controlled based on FCC data. It prevents
children from watching violent or sexual scenes that may be harmful.
• Restriction of TV programs includes two ratings that contain information about the program: the MPAA rating and
the TV Parental Guidelines. The MPAA rating is restricted by age. TV Parental Guidelines are restricted by age
and content.
• Since a TV program may use either the MPAA rating or the TV Guidelines, both should be adjusted for complete
control.
[1] MPAA RATING
RATING
age
base
G
GENERAL AUDIENCES. All ages admitted.
PG
PARENTAL GUIDANCE SUGGESTED. Some material may not be suitable for children.
PG-13
PARENTAL STRONGLY CAUTIONED. Some material may be inappropriate for children under 13.
R
RESTRICTED. Under 17 requires accompanying parent or adult guardian.
NC-17
NO ONE 17 AND UNDER ADMITTED.
X
X is an older rating that is unified with NC-17 but may be encoded in the data of older movies.:
MPAA RATING (examples)
Example 1:
PG-13 in the age-based rating is
blocked, this will also automatically
block the higher ratings R, NC-17
and X.
Example 2:
R in the age-based rating is
blocked, this will also automatically
block the higher ratings NC-17 and
X.
ote:
Note
●
The MPAA rating is only age-based.
29
LC-20B1U-GBpp19-35
29
02.2.21, 4:42 PM
ADJUSTMENT (Continued)
Adjusting the V-CHIP Settings (Continued)
[2] TV PARENTAL GUIDELINES
⇐ content base ⇒
FV
(Fantasy
Violence)
V
(Violence)
S
(Sexual
Situation)
L
(Adult
Language)
D
(Sexually
Suggestive
Dialog)
xxx
✕
✕
✕
✕
TV-14 (Parents Strongly
Cautioned)
X
✕
✕
✕
✕
TV-MA (Mature Audience Only)
X
✕
✕
✕
RATING
TV-Y (All children)
⇑
TV-Y7 (Direct to Older Children)
TV-G (General Audience)
age
base TV-PG (Parental Guidance
Suggested)
⇓
✕
X
: The content rating can be set, but this rating is not normally broadcast by TV stations.
✕ : The content rating can be set.
TV PARENTAL GUIDELINES (examples)
Example 1:
When TV-Y7 in the age-based rating is set to BLOCK, this will automatically block the higher ratings: TV-G, TV-PG, TV-14
and TV-MA. In addition, D, L, S, V and FV in CONTENT are automatically blocked unless you manually set BLOCK
CONTENT.
Example 2:
When no item in the age-based rating is blocked, D in the content-based rating will be automatically blocked.
Note
●
●
●
Age-based ratings can be modified by the content-based ratings, but only in the combinations indicated by an X in
the table above.
Choosing a lower age-based rating blocks the higher age-based ratings regardless of content rating settings.
If you set TV-Y and TV-Y7 to BLOCK, CONTENT will display all items.
30
LC-20B1U-GBpp19-35
30
02.2.21, 4:43 PM
ADJUSTMENT (Continued)
Adjusting the V-CHIP Settings (Continued)
■ SETTING V-CHIP
[1] MPAA RATING
1
Press MENU to display the MENU
screen.
2
Press ]/[ to move the cursor
to V-CHIP BLOCK, and press
ENTER.
3
INPUT SECRET NO. will be
displayed. Input the 4-digit
secret number by using the
channel select keys.
POWER
DISPLAY
SLEEP
CARD
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
MENU
Channel
Select
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
I NPUT SECRET NO .
– – – –
4
Press ]/ [ to move the cursor to
MPAA, and press ENTER.
V–CH I P BLOCK
RETURN
MPAA
TV GU I DEL I NES
STATUS [ OFF ]
SELECT :
5
Press ]/[ to move the cursor to
PG, and press ENTER.
Press </ > to select BLOCK, and
press ENTER.
If you set PG to BLOCK, PG-13,
R, NC-17 and X are automatically
blocked.
7
Press MENU to return to the main
screen.
●
●
EX I T : MENU
ENTER :
ENTER
EX I T : MENU
ENTER
EX I T : MENU
MPAA
RETURN
G
[ ––––– ]
PG
[ BLOCK ]
PG–13 [ BLOCK ]
R
[ BLOCK ]
NC– 17 [ BLOCK ]
X
[ BLOCK ]
ADJUST :
Note
ENTER
MPAA
RETURN
G
[ ––––– ]
PG
[ ––––– ]
PG–13 [ ––––– ]
R
[ ––––– ]
NC– 17 [ ––––– ]
X
[ ––––– ]
SELECT :
6
ENTER :
ENTER :
If you set G to BLOCK, all ratings are automatically blocked.
If you set X to BLOCK, G, PG, PG-13, R and NC-17 are not blocked.
31
LC-20B1U-GBpp19-35
31
02.2.21, 4:43 PM
ADJUSTMENT (Continued)
Parent Control
(V-CHIP
Operation
Continued)
Adjusting
the V-CHIP
Settings
(Continued)
[2] TV GUIDELINES
■ Setting MPAA
1
Repeat steps 1 to 3 of [1] MPAA
RATING.
2
Press ]/[ to move the cursor to
TV GUIDELINES, and press
ENTER.
POWER
DISPLAY
SLEEP
CARD
V–CH I P BLOCK
RETURN
MPAA
TV GU I DEL I NES
STATUS [ OFF ]
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
MENU
SELECT :
3
Press ]/[ to move the cursor to
TV-Y7, and press ENTER.
ENTER :
SELECT :
5
Press </ > to select BLOCK, and
press ENTER.
If you set TV-Y7 to BLOCK, TV-G,
TV-PG, TV-14 and TV-MA are
automatically blocked. In addition,
D, L, S, V and FV in CONTENT
are automatically blocked.
Press MENU to return to the main
screen.
32
ENTER :
]
ENTER
EX I T : MENU
TV GU I DEL I NES
RETURN
TV–Y [ ––––– ]
TV–Y7 [ BLOCK ]
TV–G [ BLOCK ]
TV–PG [ BLOCK ]
TV– 14 [ BLOCK ]
TV–MA [ BLOCK ]
BLOCK CONTENT
[ D L S V FV ]
ADJUST :
32
LC-20B1U-GBpp19-35
EX I T : MENU
TV GU I DEL I NES
RETURN
TV–Y [ ––––– ]
TV–Y7 [ ––––– ]
TV–G [ ––––– ]
TV–PG [ ––––– ]
TV– 14 [ ––––– ]
TV–MA [ ––––– ]
BLOCK CONTENT
[
4
ENTER
02.2.21, 4:43 PM
ENTER :
ENTER
EX I T : MENU
ADJUSTMENT (Continued)
Parent Control
(V-CHIP
Operation
Continued)
Adjusting
the V-CHIP
Settings
(Continued)
■ Setting BLOCK CONTENT
POWER
1
Repeat steps 1 to 3 of [1] MPAA
RATING.
2
Press ]/[ to move the cursor to
TV GUIDELINES, and press
ENTER.
DISPLAY
SLEEP
CARD
STATUS [ OFF ]
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
V–CH I P BLOCK
RETURN
MPAA
TV GU I DEL I NES
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
MENU
SELECT :
3
Press ]/[ to move the cursor to
BLOCK CONTENT, and press
ENTER.
ENTER :
SELECT :
Press ]/[ to move the cursor to
the desired item, and press
ENTER.
Press </ > to select BLOCK or
----- (unblock), and press ENTER.
6
Press MENU to return to the
main screen.
ENTER :
]
ENTER
EX I T : MENU
ENTER
EX I T : MENU
ENTER
EX I T : MENU
BLOCK CONTENT
RETURN
D [ ––––– ]
L [ ––––– ]
S [ ––––– ]
V [ ––––– ]
FV [ ––––– ]
SELECT :
5
EX I T : MENU
TV GU I DEL I NES
RETURN
TV–Y [ ––––– ]
TV–Y7 [ ––––– ]
TV–G [ ––––– ]
TV–PG [ ––––– ]
TV– 14 [ ––––– ]
TV–MA [ ––––– ]
BLOCK CONTENT
[
4
ENTER
ENTER :
BLOCK CONTENT
RETURN
D [ ––––– ]
L [ BLOCK ]
S [ ––––– ]
V [ ––––– ]
FV [ ––––– ]
ADJUST :
ENTER :
Note
●
If you set TV-14 to BLOCK, TV-MA is automatically blocked. Contents D, L, S and V are automatically blocked by X in the
table on page 30.
33
LC-20B1U-GBpp19-35
33
02.2.21, 4:43 PM
ADJUSTMENT (Continued)
Adjusting the V-CHIP Settings (Continued)
[3] ACTIVATE ON TO TURN ON V-CHIP BLOCK
1
Press MENU to display the MENU
screen.
2
Press ]/[ to move the cursor to
V-CHIP BLOCK, and press
ENTER.
3
INPUT SECRET NO. will be
displayed. Input the 4-digit secret
number by using the channel
select keys. (The secret number is
not displayed on the screen.)
POWER
DISPLAY
SLEEP
CARD
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
ENTER/
]/[
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
MENU
Channel
Select
MENU
SLEEP T IMER
V I DEO ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
I NPUT SECRET NO .
0 1 2 3
ENTER :
4
ENTER
Press ENTER to register the
secret number.
[4] CANCELING THE V-CHIP BLOCK SCREEN WHILE V-CHIP BLOCK IS ACTIVATED
1
POWER
DISPLAY
SLEEP
CARD
BRIGHT
●
MENU TV/VIDEO
FLASHBACK
VOL
V–CH I P HAS BEEN ACT I VATED
TV–Y
Note
ENTER
MUTE
V-CHIP HAS BEEN ACTIVATED
will be displayed if you watch the
program with Program Rating data
as same as you configured.
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
V-CHIP HAS BEEN ACTIVATED will not be
displayed if STATUS is not configured to ON.
2
Press MENU to display INPUT
SECRET NO.
3
Input the 4-digit secret number by
using the channel select keys; VCHIP BLOCK is temporarily
canceled. If you input an incorrect
secret number, SECRET NO. IS
INCORRECT is displayed. In this
case, input the correct secret
number.
MENU
Channel
Select
Note
●
If you turn the power on from off, V-CHIP BLOCK will be activated again.
If you select V-CHIP BLOCK again by using MENU, V-CHIP BLOCK will be turned on again.
34
LC-20B1U-GBpp19-35
34
02.2.21, 4:43 PM
I NPUT SECRET NO .
– – – –
EX I T : MENU
ADJUSTMENT (Continued)
Adjusting the V-CHIP Settings (Continued)
[5] CHANGING THE V-CHIP BLOCK SETTINGS
1
POWER
DISPLAY
SLEEP
Repeat steps 1 to 3 of [1] MPAA
RATING, then INPUT SECRET
NO. will be displayed.
I NPUT SECRET NO .
CARD
– – – –
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
EX I T : MENU
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
2
Channel
Select
Input the 4-digit secret number by
using the channel select keys; the
V-CHIP select mode will be
displayed. Set V-CHIP BLOCK
again.
I NPUT SECRET NO .
****
EX I T : MENU
[6] CHANGING OR CLEARING THE SECRET NUMBER
If you forget the secret number, clear the secret number as follows.
Upper control panel
of the main unit
VOL
CH
1
Repeat steps 1 to 3 of [1] MPAA
RATING, or 1 to 2 of [4]
CANCELING THE V-CHIP
BLOCK SCREEN WHILE V-CHIP
BLOCK IS ACTIVATED, then
INPUT SECRET NO. will be
displayed.
2
Press and hold both CH ( ) and
VOL (+) on the TV set simultaneously until the message INPUT
SECRET NO. blinks.
3
Press MENU to exit.
MENU
CH ( )
VOL (+)
MENU
35
LC-20B1U-GBpp19-35
35
02.2.21, 4:43 PM
MEMORY CARD PLAYBACK
Memory Cards
■ Images that have been recorded on the memory card using a digital camera or other device
and that conform to the DCF standard* can be played back in CARD mode.
* DCF (Design rule for Camera File system) is a standard of the Japan Electronics and
Information Technology Industries Association (JEITA). This standard specifies the image
file format used for images shot with a digital camera.
■ Compatible memory cards (commercially available)
Memory card name
Storage capacity
SD Memory Card
128 MB or less
CompactFlash
128 MB or less
MultiMediaCard
64 MB or less
SmartMedia
128 MB or less
Memory Stick
128 MB or less
SD Memory Card is a trademark.
CompactFlash is a trademark of the SanDisk Corporation of the USA.
MultiMediaCard is a trademark of Infineon Technologies AG of Germany.
SmartMedia is a trademark of Toshiba Corporation.
Memory Stick is a trademark of Sony Corporation.
SD Memory Card
*
MultiMediaCard
SmartMedia
PC card adapter
(commercially available)
CompactFlash
Memory Stick
In order to play back images on a memory card, a PC card adapter (commercially available)
intended for that memory card is required.
36
LC-20B1U-GBpp36-47
36
02.2.21, 4:40 PM
MEMORY CARD PLAYBACK (Continued)
Card Precautions
■ Precautions on Handling
Follow the precautions given below when handling the memory cards and PC card adapter as failure to
do so may result in damage to data or malfunction.
● Playback of images stored on memory cards other than those listed in the table on page 36 is
not guaranteed.
● Read the operation manuals for both the memory card and PC card adapter carefully as there
may be restrictions on PC card adapter operations regarding memory card storage capacity.
● For details on the proper storage and handling of the memory card and PC card adapter being
used, refer to the operation manuals supplied with both products.
● It may not be possible in some cases to play back images which have been created, modified,
copied or otherwise edited using a PC.
● Always turn the LCD TV off before inserting or removing the PC card adapter or memory card
loaded in the PC card adapter.
● Never turn off the LCD TV during memory card operations (such as when ACCESSING DATA is
●
●
●
●
●
displayed or during a SLIDE SHOW playback) as this may result in loss of data recorded on the
memory card.
During CARD mode, do not subject the system to vibration or shock of impact, and never
remove the PC card adapter or memory card loaded in the PC card adapter as this may result in
loss of data recorded on the memory card.
Do not bend, drop or subject the memory card or PC card adapter to shock of impact.
Do not store the memory card or PC card adapter in hot, humid locations or locations subject to
direct sunlight.
Avoid use and storage in an environment where strong static electricity or electrical noise is
generated.
Do not disassemble or modify the memory card or PC card adapter.
■ Storing data
Recorded data may be lost in the following cases. Sharp bears absolutely no responsibility for
recorded data that may be lost.
Data may be lost IF:
* The user or third party uses the memory card incorrectly.
* The memory card is subjected to the adverse effects of static electricity or electrical noise.
* The PC card adapter or a memory card loaded in a PC card adapter is plugged in or unplugged
while the power is turned on.
* The LCD TV is turned off during memory card operations (such as when ACCESSING DATA is
displayed or during a SLIDE SHOW playback).
We recommend that valuable data be backed up by copying to another media (such as MO disk,
floppy disk, or hard disk) before accessing that image data with this system.
37
LC-20B1U-GBpp36-47
37
02.2.21, 4:40 PM
MEMORY CARD PLAYBACK (Continued)
Preparation
1
Insert the memory card
(commercially available) on which
images have been recorded into the
PC card adapter (commercially
available).
2
Press POWER to turn off the LCD
TV.
POWER
DISPLAY
SLEEP
* Example of inserting a
memory card into a PC
card adapter.
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
POWER
CAUTION:
Always turn off the LCD TV before
plugging in or unplugging the PC
card adapter or memory card. (Never
plug in or unplug the PC card
adapter or memory card during card
playback.)
3
Cutout
Slowly insert the PC card adapter
into the PC card slot on the main
unit.
NOTE:
With its cutout positioned at the top
right, insert the PC card adapter
firmly.
Note
●
●
●
Use the appropriate PC card adapter
(commercially available) for the memory card.
Use the PC card adapter recommended by the
manufacturer of the memory card in question to
load images from the recording media that have
been shot using a digital camera. (The name
differs depending on the manufacturer.)
For details, refer to the operation manuals for
the digital camera and PC card adapter.
* Insert the PC card adapter
correctly in the direction
shown by the arrow.
* Be sure to insert the card
straight.
Pulling out the memory card
1
Press POWER to turn off the LCD TV.
2
Raise the card release lever horizontally.
3
Press the lever straight on.
Card release lever
4
Pull out the card and lower the lever.
38
LC-20B1U-GBpp36-47
38
02.2.21, 4:40 PM
MEMORY CARD PLAYBACK (Continued)
Turning on CARD Mode
POWER
</ >
1
Press POWER to turn on the LCD
TV.
2
Press CARD to change to CARD
mode.
ACCESSING DATA is displayed on
the screen.
CARD
ACCESS I NG DATA
POWER
After data from the card is loaded,
CARD is displayed on the screen.
DISPLAY
SLEEP
CARD
CARD
Note
ENTER
MUTE
BRIGHT
●
MENU TV/VIDEO
FLASHBACK
VOL
TV/VIDEO
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
3
Channel
Select
After purchasing the LCD TV, CARD
playback mode is set as the factory
settings. The next time the card is
played back, the image is displayed
in the last playback mode.
Press CARD to select a playback
mode. Each time CARD is pressed,
the playback mode changes as
follows.
CARD
■ CARD
Images on the card are displayed
one by one in full-screen, and the
next and previous images can be
displayed by selecting with </>.
■ SLIDE SHOW
Images are automatically displayed
in sequence, one by one.
The display interval for each image
can be selected from:
5SEC, 10SEC, 1MIN, 15MIN, or
60MIN
■ INDEX MODE
Images recorded on the memory
card are displayed nine images on
the screen at a time.
S L I DE SHOW
I NDE X MODE
Note
●
●
●
●
●
●
If a card error message (red) appears on the screen and images cannot be
played back, refer to TROUBLESHOOTING on page 53.
Never turn off the LCD TV during memory card operations (such as when
SELECT :
SELECT :
ENTER : ENTER
ACCESSING DATA is displayed or during a SLIDE SHOW playback) as this
may result in loss of data recorded on the memory card.
CARD mode is selected when CARD is pressed while viewing the LCD TV.
To switch CARD mode to TV mode, press any of the following buttons.
Channel Select, TV/VIDEO
Full size display may not be possible depending on the mode in which images were recorded using the digital still
camera or other device.
Turning on CARD mode and Page forwarding during INDEX MODE can only be performed using the remote control.
MY PROGRAM settings for CARD SETTING can only be made using the remote control.
39
LC-20B1U-GBpp36-47
39
02.2.21, 4:40 PM
MEMORY CARD PLAYBACK (Continued)
Selecting the Playback Mode
■
CARD playback mode
Images on the card are displayed one by one. It is possible to forward or reverse through the images.
POWER
1
Press CARD to change to CARD
playback mode.
2
Press </ > to select the desired
image to display. > cycles images
in forward sequence, while <
cycles images in reverse sequence.
ACCESSING DATA is displayed
until the next image is displayed.
CARD
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
CARD
FLASHBACK
VOL
CH
</ >
■
1
2
3
4
5
6
7
8
9
MTS
0
100
Note
●
The size of the image being displayed
differs depending on the settings
used when the shot was taken.
ACCESS I NG DATA
SLIDE SHOW playback mode
It is possible to automatically display the images registered for MY PROGRAM in sequence, one by
one. (For details on registering MY PROGRAM images, see page 44 and page 45 .)
1
POWER
DISPLAY
SLEEP
Press CARD to switch to SLIDE
SHOW playback mode.
S L I DE SHOW
CARD
Note
ENTER
MUTE
BRIGHT
●
MENU TV/VIDEO
CARD
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
●
●
2
The first time SLIDE SHOW playback
mode is selected after purchase,
operations are performed according
to default factory settings.
Default factory settings are as
follows.
INTERVAL: 5SEC
ORDER TO SHOW: NORMAL
REPEAT: ON
Depending on the loading time
required for the data to be displayed
next, the current image may be
displayed longer than the display time
that has been set.
Perform SLIDE SHOW settings to
change default factory settings. (see
page 43)
To stop SLIDE SHOW playback,
press CARD to switch to other
playback mode.
Note
●
The SLIDE SHOW playback is
paused while the MENU screen is
displayed.
40
LC-20B1U-GBpp36-47
40
02.2.21, 4:40 PM
MEMORY CARD PLAYBACK (Continued)
Selecting the Playback Mode (Continued)
■ INDEX playback mode
It is possible to display nine images at a time.
1
POWER
DISPLAY
SLEEP
CARD
I NDE X MODE
Press CARD to switch to INDEX
MODE.
Nine images are displayed on the
screen at a time.
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
CARD
FLASHBACK
VOL
CH
SELECT :
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
2
SELECT :
Select an image using ]/[/</ >,
and press ENTER. Only the
selected image is displayed on the
screen in CARD playback mode.
ENTER :
ENTER
CARD
Note
●
●
The DISPLAY button does not function on the INDEX MODE screen.
In INDEX MODE, the contents displayed differ as described below depending on the ORDER TO SHOW setting made
for SLIDE SHOW playback mode.
NORMAL/RANDOM: All image files on the memory card are displayed nine at a time.
MY PROGRAM: Only images registered for SET PROGRAM are displayed.
Page Forwarding
Selection marker (yellow)
1
Press > to move the selection
marker to the image on the right
side.
2
Press > to move the selection
marker to the triangular mark on
the right end of the screen.
The triangular mark turns yellow.
I NDE X MODE
SELECT :
3
Press > one more time. The
display changes to that for the next
page of index images.
The selection marker is displayed
on the center image on the left.
S ELECT :
SELECT
ENTER :
ENTER
I NDE X MODE
Page Reverse
To reverse through pages, use the
same operation as described above
pressing <.
SELECT :
S ELECT :
SELECT
ENTER :
ENTER
Note
● It is impossible to switch the playback mode even by pressing CARD while the triangular mark /
on the INDEX MODE
screen is selected (yellow).
● If the Page Forwarding operation is used on the last page of images, the display returns to the first page.
● On the first page, a triangular mark
is not displayed on the left.
41
LC-20B1U-GBpp36-47
41
02.2.21, 4:40 PM
CARD ADJUSTMENT
Selecting CARD SETTING Items
CARD SETTING on the MENU screen can be used to make various settings such as SLIDE SHOW, MY
PROGRAM, ROTATE and SOUND SETTING. Select the desired item by following the steps below and
then refer to the indicated page for details.
CARD
1
2
3
Turn on CARD mode. (see page 39)
4
Press ]/[ to select the desired setting item, and press ENTER.
Press MENU to display the MENU screen.
Press ]/[ to move the cursor to CARD SETTING, and press
ENTER.
MENU
CARD SE TT I NG
SLEEP T IMER
V I DEO ADJUST
PRESET
V–CH I P BLOCK
SET UP
(Page 43)
SELECT :
ENTER :
ENTER
EX I T : MENU
SL I DE SHOW SE T T I NG
RETURN
I NTERVAL
[
5SEC
]
ORDER TO SHOW [MY PROGRAM]
[
ON
]
REPEAT
ENTER :
SELECT :
ENTER
EX I T : MENU
(Pages 44, 45)
ENTER
●
●
MY PROGRAM
RETURN
SE T PROGRAM
ERASE ALL PROGRAM
ENTER :
●
●
●
●
CARD SE TT I NG
RETURN
SL I DE SHOW SE T T I NG
MY PROGRAM
ROTATE
SOUND SETT I NG
SELECT :
Note
●
EX I T : MENU
CARD
●
SELECT :
ENTER :
ENTER
EX I T : MENU
POWER
(Page 46)
DISPLAY
SLEEP
●
ROTATE
RETURN
ROTATE
CHOOSE F I L E
CARD
●
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
MENU
SELECT :
CHANGE :
ADJUST
EX I T : MENU
●
(Page 47)
SOUND SETT I NG
RETURN
TV
[ON]
[--]
AV1
AV2
[--]
COMPONENT [ - - ]
SELECT :
ENTER :
●
ENTER
The displayed items differ depending on
the setting conditions.
The selected item chages to yellow.
Items in magenta cannot be selected.
To return to the previous screen, select
RETURN.
CARD SETTING is displayed on the
MENU screen only during CARD mode.
CARD SETTING cannot be selected until
the system determines that the card can
be used.
CLOSED CAPTION is not displayed on
the MENU screen during CARD mode.
Select TV/VIDEO mode and then set the
CLOSED CAPTION settings.
The only VIDEO ADJUST settings
available during CARD mode are
PICTURE, RESET and RETURN.
COLOR SYSTEM is always set to N358
and cannot be changed during CARD
mode.
The BLUE SCREEN, CH-SETTING,
CLOSED CAPTION, V-CHIP BLOCK,
AUTO POWER OFF functions and video
output do not operate during CARD
mode.
If MY PROGRAM is set in ORDER TO
SHOW for SLIDE SHOW settings, only
registered images will be played back in
INDEX MODE.
The ROTATE settings cannot be selected
in INDEX MODE.
EX I T : MENU
42
LC-20B1U-GBpp36-47
42
02.2.21, 4:40 PM
CARD ADJUSTMENT (Continued)
Adjusting the SLIDE SHOW Settings
You can set the desired display time and playback order. REPEAT setting is also available.
CARD
POWER
1
Press CARD to change to CARD
mode.
2
Press CARD to switch to SLIDE
SHOW as the playback mode.
3
Press MENU to display the MENU
screen.
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
FLASHBACK
VOL
4
MENU TV/VIDEO
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</ >
Press ]/[ to move the cursor to
CARD SETTING, and press
ENTER.
S L I DE SHOW
MENU
CARD SE TT I NG
SLEEP T IMER
V I DEO ADJUST
PRESET
V–CH I P BLOCK
SET UP
MENU
SELECT :
5
Press ]/[ to move the cursor to
SLIDE SHOW SETTING, and press
ENTER.
Press ]/[ to select the desired
setting item, and press ENTER.
7
Press </ > to change the setting,
and press ENTER.
ENTER
EX I T : MENU
CARD SE TT I NG
RETURN
SL I DE SHOW SE T T I NG
MY PROGRAM
ROTATE
SOUND SETT I NG
SELECT :
6
ENTER :
ENTER :
ENTER
EX I T : MENU
SL I DE SHOW SE T T I NG
RETURN
I NTERVAL
[
5SEC
]
ORDER TO SHOW [MY PROGRAM]
[
ON
]
REPEAT
■ The following SLIDE SHOW settings
are available.
INTERVAL:
SELECT :
5SEC
10SEC
1MIN
60MIN
15MIN
ORDER TO SHOW:
NORMAL
RANDOM
MY PROGRAM
REPEAT: ON
8
ENTER :
ENTER
EX I T : MENU
SL I DE SHOW SE T T I NG
RETURN
I NTERVAL
[
5SEC
]
ORDER TO SHOW [MY PROGRAM]
[
ON
]
REPEAT
OFF
Press MENU to exit.
ADJUST :
ENTER :
ENTER
EX I T : MENU
Note
●
●
The above time setting for INTERVAL is the minimum display time per image. Actual playback time for an image may
vary depending on the data size and the time required to load the image from the media.
Although pressing MENU will pause the SLIDE SHOW playback, the SLIDE SHOW playback continues when you exit
the MENU screen.
43
LC-20B1U-GBpp36-47
43
02.2.21, 4:40 PM
CARD ADJUSTMENT (Continued)
Adjusting the MY PROGRAM Settings
You can select and register any of up to nine images from a large number of images. Images registered
for MY PROGRAM are displayed in the specified sequence in SLIDE SHOW playback mode.
■ Registering MY PROGRAM Images
CARD
POWER
1
Press CARD to change to CARD
mode.
2
Press MENU to display the MENU
screen, press ]/[ to move the
cursor to CARD SETTING, and
press ENTER to display the CARD
SETTING screen.
3
Press ]/[ to move the cursor to
MY PROGRAM, and press ENTER.
4
Press ]/[ to move the cursor to
SET PROGRAM, and press
ENTER.
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CARD SE TT I NG
RETURN
SL I DE SHOW SE T T I NG
MY PROGRAM
ROTATE
SOUND SETT I NG
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</>
MENU
CARD SE TT I NG
RETURN
SL I DE SHOW SE T T I NG
MY PROGRAM
ROTATE
SOUND SETT I NG
MY PROGRAM
RETURN
SE T PROGRAM
ERASE ALL PROGRAM
SELECT :
5
Press </ > to select the location at
which the image to be registered,
moving the selection marker (red)
in the registration area, and press
ENTER.
The location to be registered can
be selected from 1 through 9 in the
specified number.
ENTER :
ENTER
EX I T : MENU
Registration area
Selection marker (red)
MY PROGRAM
1
SELECT :
2
ENTER :
ENTER
3
EX I T : MENU
Selection area
Note
●
●
●
The previous three images are displayed by aligning the selection marker (red) with the triangular mark and
pressing <.
The next three images are displayed by aligning the selection marker (red) with the triangular mark and pressing >.
The image registered for MY PROGRAM is erased when another card is inserted.
The images that have been registered for MY PROGRAM are played back when MY PROGRAM is selected in
ORDER TO SHOW for the SLIDE SHOW SETTING. (For details on the settings, see page 43.) Only registered images
are displayed on the INDEX MODE screen at this time.
44
LC-20B1U-GBpp36-47
44
02.2.21, 4:40 PM
CARD ADJUSTMENT (Continued)
Adjusting the MY PROGRAM Settings (Continued)
6
Press ]/[/</ > to select the
Selection marker (yellow)
image to be registered, moving the
MY PROGRAM
selection marker (yellow) in the
1
2
selection area, and press ENTER.
The image is then registered in the
registration area that was specified
in step 4. (see page 44)
7
Repeat steps 5 and 6 to register
more images.
SELECT :
Note
The previous six images are displayed by
aligning the selection marker (yellow) with
the triangular mark and pressing <.
The next six images are displayed by
aligning the selection marker (yellow) with
the triangular mark and pressing >.
If an image is registered in a location
number for which another image has
already been registered, the previous
image is dropped from the registered
entries and overwritten by the new image.
●
●
3
ENTER :
MY PROGRAM
1
SELECT :
ENTER
2
ENTER :
ENTER
EX I T : MENU
3
EX I T : MENU
■ Erasing the MY PROGRAM Settings
POWER
1
Press MENU to display the MENU
screen, press ]/[ to move the
cursor to CARD SETTING, and
press ENTER to display the CARD
SETTING screen.
2
Press ]/[ to move the cursor to
MY PROGRAM, and press ENTER.
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[
MENU
CARD SE TT I NG
RETURN
SL I DE SHOW SE T T I NG
MY PROGRAM
ROTATE
SOUND SETT I NG
SELECT :
3
Press ]/[ to move the cursor to
ERASE ALL PROGRAM, and press
ENTER. All images in the
registration area will be erased.
ENTER :
ENTER
EX I T : MENU
ENTER
EX I T : MENU
MY PROGRAM
RETURN
SE T PROGRAM
ERASE ALL PROGRAM
SELECT :
ENTER :
MY PROGRAM
1
2
3
Note
●
Repeat steps 4 and 5 given in
“Registering MY PROGRAM Images”
to register new images.
SELECT :
ENTER :
ENTER
EX I T : MENU
45
LC-20B1U-GBpp36-47
45
02.2.21, 4:41 PM
CARD ADJUSTMENT (Continued)
Adjusting the ROTATE Settings
• You can rotate a recorded image.
• You can move to the next or previous image by selecting CHOOSE FILE even if you have not exited
the ROTATE screen.
■ Rotating Images
When the image that you want to rotate is displayed in CARD or SLIDE
SHOW playback mode, follow the steps below to rotate the image.
CARD
1
Press MENU to display the MENU
screen, press ]/[ to move the
cursor to CARD SETTING, and
press ENTER to display the CARD
SETTING screen.
2
Press ]/[ to move the cursor to
ROTATE, and press ENTER.
3
Press </ > to rotate the image.
POWER
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
CARD SE TT I NG
RETURN
SL I DE SHOW SE T T I NG
MY PROGRAM
ROTATE
SOUND SETT I NG
ENTER/
]/[/
</ >
MENU
CARD
ROTATE
RETURN
ROTATE
CHOOSE F I L E
Press <: Rotates 90 degrees
counterclockwise.
Press >: Rotates 90 degrees
clockwise.
SELECT :
Note
ROTATE settings are canceled if power is
turned off without registering the rotated
image in the MY PROGRAM setting.
● The ROTATE settings cannot be selected
in INDEX MODE.
●
ADJUST :
EX I T : MENU
ROTATE
RETURN
ROTATE
CHOOSE F I L E
SELECT :
ADJUST :
E X I T : MENU
EX
■ Selecting a file
Press ]/[ to move the cursor to CHOOSE FILE on the ROTATE
screen and select an image by pressing </ >.
ROTATE
RETURN
ROTATE
CHOOSE F I L E
Press <: To the previous file
Press >: To the next file
Note
●
●
CHOOSE FILE is displayed in magenta and cannot be selected when RANDOM
is selected for the SLIDE SHOW settings.(see page 43)
CHOOSE FILE may turn magenta during ROTATE processing.
SELECT :
46
LC-20B1U-GBpp36-47
46
02.2.21, 4:41 PM
ADJUST :
E X I T : MENU
EX
CARD ADJUSTMENT (Continued)
Adjusting the SOUND Settings
You can listen to the audio from TV or external devices such as VCR or DVD player, etc. through the TV
set while card playback.
CARD
POWER
1
Press CARD to change to CARD
mode.
2
Press MENU to display the MENU
screen, press ]/[ to move the
cursor to CARD SETTING, and
press ENTER to display the
CARD SETTING screen.
3
Press ]/[ to move the cursor to
SOUND SETTING, and press
ENTER.
DISPLAY
SLEEP
CARD
ENTER
MUTE
BRIGHT
MENU TV/VIDEO
FLASHBACK
VOL
CARD SE TT I NG
RETURN
SL I DE SHOW SE T T I NG
MY PROGRAM
ROTATE
SOUND SETT I NG
CH
1
2
3
4
5
6
7
8
9
MTS
0
100
ENTER/
]/[/
</>
MENU
4
Press ]/[ to select the desired
setting item, and press ENTER.
MTS
SELECT :
Press </ > to select ON or -(OFF), and press ENTER.
■
•
•
•
•
■
You can select only one of the
following items for the SOUND
SETTING during card playback.
TV: Outputs the audio from TV prior
to switching to CARD mode.
STEREO audio or SAP is set as
the audio on the television
screen.
AV1: Outputs the audio from AV-IN1
terminal.
AV2: Outputs the audio from AV-IN2
terminal.
COMPONENT:
Outputs the audio from
COMPONENT terminal.
EX I T : MENU
ENTER :
ENTER
EX I T : MENU
ENTER
EX I T : MENU
SOUND SETT I NG
RETURN
[ON]
TV
[--]
AV1
[--]
AV2
COMPONENT [ - - ]
ADJUST :
During CARD mode, the SOUND
SETTING can be changed by pressing
MTS on the remote control. Each time
MTS is pressed, the SOUND SETTING
will be changed as follows.
No sound
TV
COMPONENT
ENTER
SOUND SETT I NG
RETURN
TV
[--]
[--]
AV1
[--]
AV2
COMPONENT [ - - ]
SELECT :
5
ENTER :
ENTER :
C ARD
TV
AV1
AV2
Note
●
●
●
Audio recorded on the memory card cannot be played back.
If any of the sound item is set to ON, all other sound item will be automatically set to -- (OFF).
When OUT has been selected as the AV2 IN/OUT setting, it is not possible to set AV2 to ON in SOUND SETTING for
CARD mode. In order to set AV2 to ON, select IN as the AV2 IN/OUT setting.
47
LC-20B1U-GBpp36-47
47
02.2.21, 4:41 PM
CONNECTING WITH EXTERNAL DEVICES
You can enjoy picture and sound by connecting a VCR or a home video game system to the terminals
located on the rear of the TV set.
When connecting an external device, turn off the power of the main unit first to prevent any possible
damage.
Example of external devices that can be connected
External devices that can be connected
to AV-IN2 terminal
<Example>
• VCR
• Laser disc player
External devices that can be connected
to AV-IN1 terminal
<Example>
• Video camera
• Home video game system
* If your external device has an
S-Video terminal, S-VIDEO
connection is recommended.
* If your external device has an S-Video terminal,
S-VIDEO connection is recommended.
External devices that can be connected
to COMPONENT terminal
CH
MENU TV/VIDEO
<Example>
• DVD, etc.
MAIN POWER
VOL
DVD TUNER/BAND AUX 1
AUX 2
AUX 3
SURROUND
ON/OFF
* If your external device has a component
terminal, COMPONENT connection is
recommended (you can view high-quality
pictures). If your external device does not
have a component terminal, S-VIDEO
connection is recommended.
Note
●
●
●
●
●
PC connection is not possible.
For the cable, use a commercially available audio/video cord.
Only connect audio/video signals to AV-IN1 and 2 terminals. Connecting other signals may result in a malfunction.
AV-IN1 has 2 video input terminals: VIDEO and S-VIDEO. When you connect external devices to both terminals
(and if you select AV-IN1), you can only view pictures from the S-VIDEO terminal. To view the picture from the
VIDEO terminal, do not connect any external device to the S-VIDEO terminal.
For more information about external device connections, see the manuals of your external devices.
48
LC-20B1U-GBpp48-58
48
02.2.21, 4:39 PM
CONNECTING WITH EXTERNAL DEVICES (Continued)
Connecting a VCR, DVD player or a video camera (AV-IN1/2/COMPONENT)
To AV-IN2 terminal
VIDEO
UT
AV-IN2/O
L
AUDIO
R
Video
ONENT
Y
COMP
Audio (L)
PB
Audio (R)
PR
L
To audio/video output
terminal
AUDIO
R
VCR
To component input
(Video) terminal
Y
CH
MENU TV/VIDEO
MAIN POWER
VOL
PB
PR
Audio (L)
Audio (R)
To component input
(Audio) terminal
DVD TUNER/BAND AUX 1
AUX 2
AUX 3
SURROUND
ON/OFF
DVD Player
To AV-IN1 terminal
Video
VIDEO
AV-IN
Audio (L)
1
L
AUDIO
Audio (R)
R
To audio/video output
terminal
S-VIDE
O
Video camera
HEAD
PHON
E
To S-video input terminal
ANT.
S-Video
VCR
POWER
INPUT
DC13V
To S-video output terminal
Note
● If your VCR (or other external devices) has an S-Video terminal, S-VIDEO connection is recommended. (Use an
S-video cord.)
● When you connect external devices to both S-VIDEO and VIDEO terminals (and if you select AV-IN1), you can
only view pictures from the S-VIDEO terminal.
● You cannot view multiple or synthesized pictures by connecting two or more external devices. When connecting
an external device, use care to connect the video and audio cables to the corresponding terminals.
● Do not connect antennas or headphones to AV-IN2.
49
LC-20B1U-GBpp48-58
49
02.2.21, 4:39 PM
CONNECTING WITH EXTERNAL DEVICES (Continued)
Outputting video and audio (video output)
You can output video and audio data from the TV set through the AV output terminals (AV-OUT).
VIDEO
OUT
Connect a VCR,
Audio amplifier,
etc.
AV-IN2/
L
AUDIO
R
ONENT
Y
COMP
CH
MENU TV/VIDEO
MAIN POWER
VOL
PB
PR
L
AUDIO
R
Note
AV2 has 2 OUT modes (see page 24).
When using the S-Video input for AV-IN1, no video output will be made to the AV output terminal, but audio
output will be made for connection to external audio systems.
Note:
● It is impossible for card images to video output.
●
●
How to fix the cables
CH
MENU TV/VIDEO
• Fix cables and cords with the attached cable
clamps so that they do not get caught when
mounting the cover.
• Connect the cables and cords after fixing the
cable clamps (2 positions).
MAIN POWER
VOL
Cable clamps
50
LC-20B1U-GBpp48-58
50
02.2.21, 4:39 PM
TROUBLESHOOTING
■ Before calling for repair service, check the following items for possible remedies to
the encountered symptoms.
TV set
Problem
Sound
Picture
Picture
Check item
There is no
picture or
sound.
There is no
picture.
There is no
picture from
AV-IN 1.
There is no
sound.
There is no
picture or
sound, just
noise.
Picture is not
clear.
Picture is light
or improperly
tinted.
The picture is
too dark.
Remote control does not work.
• Make sure the AC adapter is properly inserted in the
power outlet.
• Reception other than those of broadcasting stations
can be considered.
• Make sure the input mode is set to TV.
• Make sure the main power switch of the main unit is
on.
• Make sure the BLACK LEVEL is properly adjusted.
• Fluorescent lamp may have reached the end of
service life.
• Make sure the S-Video terminal is free of connections.
Reference
Pages
9
15
15
22, 23
–
49
• Make sure the volume is not set to minimum.
• Make sure the sound is not set to mute.
• Make sure that headphones are not connected.
16
16
13
• Make sure the antenna cable is properly connected.
• Consider whether TV signals are being properly
received.
9
–
• Make sure the antenna cable is properly connected.
• Consider whether TV signals are being properly
received.
9
–
• Check color adjustment.
• Check color system setting.
22, 23
• Press the Brightness button.
• Check PICTURE and BLACK LEVEL adjustment.
• Fluorescent lamp may have reached the end of
service life.
• Check the batteries of the remote controller.
• Make sure the remote sensor window is not under
strong fluorescent lighting.
22, 23
54
8
8
51
LC-20B1U-GBpp48-58
51
02.2.21, 4:39 PM
TROUBLESHOOTING (Continued)
Antenna
Problem
Check item
The picture is
not sharp.
•
•
•
•
The reception may be weak.
The state of the broadcast may also be bad.
Make sure the antenna is facing the right direction.
Make sure the outside antenna is not disconnected.
The picture
moves.
The picture is
doubled or
tripled.
The picture is
spotted.
There are
stripes on the
screen or
colors fade.
• Make sure the antenna is facing the right direction.
• There may be reflected electric waves from mountains or
buildings.
• There may be interference from automobiles, trains, high
voltage lines, neon lights, etc.
• There may be interference between the antenna cable and
power cable. Try positioning them further apart.
• Is the unit receiving interference from other devices?
Transmission antennas of radio broadcasting stations and
transmission antennas of amateur radios and cellular phones
may also cause interference.
• Use the unit as far apart as possible from devices that may
cause possible interference.
■ Use in hot and cold rooms (locations)
• When the unit is used in a low temperature rooms (location), the picture may leave trails or appear slightly
delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight
or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
(Storage temperature: –20°C to +60°C)
52
LC-20B1U-GBpp48-58
52
02.2.21, 4:39 PM
TROUBLESHOOTING (Continued)
Card
Problem
Check item
Reference
Pages
Data on the card cannot be
played back.
• Check if data is recorded on the memory card.
• Check if CARD mode is turned on as the input
selection.
• Images which have been processed by a PC
sometimes cannot be played back by this equipment.
NO CARD INSERTED*1 is
displayed.
• Check that the memory card and/or PC card adapter
are inserted.
38
NO IMAGE IN THE CARD*1 is
displayed.
• Use a memory card containing recorded image data.
–
ACCESSING DATA*2 is
displayed.
• This message disappears after data has finished
loading.
–
PLEASE SET MY PROGRAM is
displayed.
• Register images for MY PROGRAM.
39
44, 45
*1 CARD SETTING on the MENU screen is displayed in magenta and cannot be selected.
*2 Desired operaions may be selected after data has been loading from the card.
53
LC-20B1U-GBpp48-58
53
02.2.21, 4:39 PM
SPECIFICATIONS
Items
Model
LCD panel
Number of dots
Video color systems
Destination
TV Standard (CCIR)
TV function
TV Tuning System
STEREO
CATV
3 Dimensional Y/C separation circuit
Digital comb filter
Brightness
Lamp life
Viewing angles
Audio amplifier
Speakers
AV1
AV2
Terminals
COMPONENT
Antenna
Headphone
PC Card slot
Image File Format
OSD language
Power supply
Weight
Accessories
LC-20B1U
19.7” Advanced Super View & BLACK TFT LCD
921,600 dots VGA
N358, N443, PAL, PAL-M, PAL-N, SECAM, PAL-60
USA/Latin A/Twn
NTSC/PAL-M/PAL-N
PLL 181 ch.
MTS+SAP
125 ch.
Yes (N358 only)
Yes
430 cd/m2
60,000 hours
H: 170° V: 170°
2.5 W × 2
ø 2 in. (5 cm), 2 pcs.
AV-IN1, S-VIDEO-IN
AV-IN2/AV-OUT
COMPONENT-IN, AUDIO-IN
F-Type
Mini-jack for stereo (3.5 ø)
PC Card Type II (PC card adapter)
JPEG files complying with DCF format.
English/French/Spanish
DC 13 V, AC 110–240 V, 50/60 Hz
19 lbs (8.6 kg), w/o accessories
Remote control, Batteries, Antenna cable, AC adapter,
AC cord, Cable clamps
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of
production units. There may be some deviations from these values in individual units.
54
LC-20B1U-GBpp48-58
54
02.2.21, 4:39 PM
DIMENSIONAL DRAWINGS
VOL
CH
MENU TV/VIDEO
2.86/72.6
2.62/66.6
1.58/40
Unit: inch/mm
MAIN POWER
12.6/319
24.8/630
11.8/298.8
15.0/381.5
7.6/193.5
18.6/473.5
7.4/188
15.8/401.3
14.9/379
4.2/107.3
2.9/72.6
18.5/468.8
L
AUDIO
R
Y
0.06/1.5
VIDEO
AV-IN 2/OUT
COMPONENT
3.94/100
3.45/87.5
1.58/40
VIDEO
AV-IN1
L
AUDIO
R
S-VIDEO
HEAD
PHONE
PB
ANT.
PR
L
AUDIO
R
3.94/100
POWER
INPUT
DC12V
1.2/30.5
6.5/163.9
2.6/65.5
9.0/229.4
55
LC-20B1U-GBpp48-58
55
02.2.21, 4:39 PM
CALLING FOR SERVICE
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or customer
assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
END-USER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp brand product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it
will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured
equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and exclusive of, all other
warranties, express or implied. Specifically, ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE
EXCLUDED. ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR USE, AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under
applicable state law, implied warranties may not validly be disclaimed or excluded, the duration of such implied warranties is
limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any
way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on
warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.
Model Specific Section
Your Product Model Number & Description:
LC-20B1U LCD Color Television
(Be sure to have this information available when you need service for
your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from
Warranty Coverage (if any):
None
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States.
To find the location of the nearest Sharp Authorized Servicer, call
Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product,
be sure it is insured and packaged securely.
TO OBTAIN PRODUCT INFORMATION, CALL 1-888-LCD-SHARP.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
56
LC-20B1U-GBpp48-58
56
02.2.21, 4:39 PM
VALID IN CANADA ONLY
LIMITED WARRANTY
Consumer Electronics Products
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for this
Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer:
Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any such
defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the product as
specified herein.
This warranty shall not apply to:
(a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate
use as outlined in the owner’s manual.
(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp’s Authorized Service Centres
or Sharp’s Authorized Servicing Dealers.
(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited to
head cleaning tapes and chemical cleaning agents.
(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including but
not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons, cables and
paper.
(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.
(f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or liquid
spillage.
(g) Any product received without appropriate model, serial number and CSA/cUL markings.
(h) Any products used for rental or commercial purposes.
(i) Any installation, setup and/or programming charges.
Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product
together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an
Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp’s discretion on any Sharp television with the
screen size of 27” or larger and on any Sharp Over-the-Range Microwave Oven.
This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is
authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all
liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a
defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss
of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of
defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp
to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict
liability or otherwise.
WARRANTY PERIODS:
Audio Products
Camcorder
DVD Products
LCD Projector
LCD TV
Microwave Oven
Television Products
VCR Product
Vacuum Cleaner
Parts &
1 year
1 year
1 year
1 year
1 year
2 years
1 year
1 year
1 year
Labour (exceptions noted)
(lamp 90 days)
(magnetron component-3 additional years)
(picture tube component-1 additional year)
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9
For more information on this Warranty, Sharp Extended Warranty
Offers, Sharp Canada Products, Accessory Sales, Dealer or Service
Locations, Tronto please call (905) 568-7140
Visit our Web site: www.sharp.ca
LC-20B1U-GBpp48-58
57
02.2.21, 4:39 PM
LC-20B1U-GBpp48-58
58
02.2.21, 4:39 PM