Bosch ART COMBITRIM Instruction manual

F 016 L70 621.book Seite 1 Montag, 30. November 2009 3:03 15
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke
gebruiksaanwijzing
Original brugsanvisning
Bruksanvisning i original
Original driftsinstruks
Alkuperäiset ohjeet
Πρωττυπο οδηγιών
χρήσης
Orijinal iµletme talimat∂
Instrukcja oryginalna
PÛvodní návod k pouÏívání
Pôvodn˘ návod na pouÏitie
Eredeti használati utasítás
Оригинальное руководство по эксплуатации
Оригінальна інструкція з
експлуатації
Instrucøiuni originale
Оригинална инструкция
Originalno uputstvo za rad
Izvirna navodila
Originalne upute za rad
Algupärane kasutusjuhend
Instrukcijas oriinālvalodā
Originali instrukcija
Deutsch
English
Français
Español
Português
Italiano
Nederlands
Dansk
Svenska
Norsk
Suomi
Eλληνικά
Türkçe
Polski
âesky
Slovensky
Magyar
Русский
Українська
Românå
Български
Srpski
Slovensko
Hrvatski
Eesti
Latviešu
Lietuviškai
ART COMBITRIM
F 016 L70 621.book Seite 2 Montag, 30. November 2009 3:03 15
360°
16
1
13
15
14
2
17
3
4
13
5
6
8
7
12
11
9
2 • F 016 L70 621 • 09.11
10
F 016 L70 621.book Seite 3 Montag, 30. November 2009 3:03 15
B1
A
10
➋
6
➊
CLI
CK
!
➊
11
7
➋
B3
B2
18
19
18
11
3 • F 016 L70 621 • 09.11
F 016 L70 621.book Seite 4 Montag, 30. November 2009 3:03 15
C
D
5
90°
➋
➊
➊
6
3
➋
4
F
E
6
➊ ➌
18
➋
11
6
12
4 • F 016 L70 621 • 09.11
90¡
F 016 L70 621.book Seite 5 Montag, 30. November 2009 3:03 15
G
H
➊
6
12
➋
5
90°
6
7
I
J
9
5 • F 016 L70 621 • 09.11
F 016 L70 621.book Seite 6 Montag, 30. November 2009 3:03 15
K
L
9
9
20
N
M
26
27
25
21
22
25
23
10
O
24
13
14
6 • F 016 L70 621 • 09.11
CLICK!
F 016 L70 621.book Seite 7 Montag, 30. November 2009 3:03 15
F 016 800 178
F 016 800 175
F 016 800 176
F 016 800 174
(ART 23/2300 COMBITRIM)
10x
F 016 800 181
(ART 26/2600 COMBITRIM)
F 016 800 182
(ART 30/3000 COMBITRIM)
F 016 800 172
F 016 800 173
7 • F 016 L70 621 • 09.11
F 016 L70 621.book Seite 1 Montag, 30. November 2009 3:03 15
Safety Notes
Warning! Read these instructions carefully, be
familiar with the controls and the proper use of
the line trimmer. Please keep the instructions
safe for later use.
Explanation of symbols on the line trimmer
General hazard safety alert.
Read instruction manual.
Wear eye protection.
360°
Beware of thrown or flying objects to bystanders.
Keep bystanders a safe distance away from the machine.
Switch off and remove plug from mains before adjusting, cleaning or if the cable is entangled and before leaving the trimmer unattended for any period. Keep the supply flexible cord away from the cutting line.
Do not work in the rain or leave the trimmer
outdoors whilst it is raining.
■ Never operate the trimmer with damaged guards
or shields or without guards or shields in position.
■ Before use check the supply and extension cord
for signs of damage or ageing. If the cord becomes damaged during use, disconnect the cord
from the supply immediately. DO NOT TOUCH
THE CORD BEFORE DISCONNECTING THE
SUPPLY. Do not use the trimmer if the cord is
damaged or worn.
■ Before using the machine and after impact, check
for signs of wear or damage and repair if necessary.
■ Do not operate the trimmer when barefoot or
wearing open sandals, always wear substantial
footwear and long trousers.
■ Keep extension cords away from cutting elements.
■ Never allow children or people unfamiliar with
these instructions to use the trimmer. Local regulations may restrict the age of the operator. When
not in use store the trimmer out of reach of children.
15 • F 016 L70 621 • 09.11
■ This appliance is not intended for used by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of
the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they
do not play with the appliance.
■ Never work with this trimmer while people, especially children or pets are nearby.
■ The operator or user is responsible for accidents
or hazards occurring to other people or their property.
■ Wait until the rotating line has completely stopped
before touching it. The line continues to rotate after the trimmer is switched off, a rotating line can
cause injury.
■ Work only in daylight or in good artificial light.
■ Avoid operating the trimmer in wet grass, where
feasible.
■ Switch off when transporting the trimmer to and
from the area to be worked on.
■ Switch on the trimmer with hands and feet well
away from the rotating line.
■ Do not put hands or feet near the rotating line.
■ Never fit metal cutting elements to this trimmer.
■ Inspect and maintain the trimmer regularly.
■ Have the trimmer repaired only by an authorized
customer service agent.
■ Always ensure that the ventilation slots are kept
clear of debris.
■ Take care against injury from the blade fitted for
cutting the nylon line length. After feeding line always return the trimmer to its horizontal operating
position before switching on.
■ Do not feed and cut off excess line in edging position.
■ Switch off and remove the plug from the
socket:
– whenever you leave the machine unattended for
any period
– before replacing the spool
– if the cable is entangled
– before cleaning or working on the line trimmer.
■ Store the machine in a secure dry place out of
reach of children. Do not place other objects on
top of the machine.
■ Replace worn or damaged parts for safety.
■ Ensure replacement parts fitted are Bosch approved.
English - 1
F 016 L70 621.book Seite 2 Montag, 30. November 2009 3:03 15
Technical data
Line trimmer
Part number (typ)
Rated power
No-load speed
Cutting line feed
Adjustable handle
Cutting Head angle
adjustment/edging
adjustment
Cutting line
Cutting circle
Cutting spool
capacity
Extra Strong Line
Weight (without
optional extras)
Protection class
Serial Number
ART 23 COMBITRIM/
ART 2300 COMBITRIM
3 600 H78 B..
[W]
400
[min-1] 12 000
Pro tap automatic
●
ART 26 COMBITRIM/
ART 2600 COMBITRIM
3 600 H78 C..
450
11 500
Pro tap automatic
●
ART 30 COMBITRIM/
ART 3000 COMBITRIM
3 600 H78 D..
500
10 500
Pro tap automatic
●
[mm]
[cm]
●
Ø 1.6
23
●
Ø 1.6
26
●
Ø 1.6
30
[m]
[mm]
8
Ø 2.4
8
Ø 2.4
8
Ø 2.4
[kg]
2.7
3.0
/ II
/ II
See serial No 16 (rating plate) on machine.
Intended Use
/ II
Operating Controls
The product is intended for the cutting of grass and
weeds under bushes, as well as on slopes and
edges that can not be reached with the lawn mower.
Intended Use is related to operation within 0 °C and
40 °C ambient temperature.
Introduction
This manual gives instructions on the correct assembly and safe use of your machine. It is important
that you read these instructions carefully.
Delivered Items
Carefully remove the machine from its packaging
and check that you have all the following items:
– Line trimmer
– Cutting guard
– Adjustable handle (fitted)
– Wheels (ART 30/3000 COMBITRIM only)
– Plant protector (ART 30/3000 COMBITRIM only)
– Extra Strong Line
– Operating instructions
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
On/Off switch
Handle
Handle wing nut
Adjustable handle
Adjusting collar
Shaft
Trimmer head
Ventilation slots
Plant protector
(ART 30/3000 COMBITRIM only)
Cutting guard
Wheels (ART 30/3000 COMBITRIM only)
Foot pedal for head angle adjustment
Extra Strong Line
Extra Strong Line spool
Mains plug**
Serial Number
**Country specific
Not all of the accessories illustrated or described are
included as standard delivery.
When parts are missing or damaged, please contact your
dealer.
16 • F 016 L70 621 • 09.11
3.2
English - 2
F 016 L70 621.book Seite 3 Montag, 30. November 2009 3:03 15
For Your Safety
Assembly
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
The cutting line continues to rotate for a few
seconds after the trimmer is switched off.
Caution – do not touch rotating cutting line.
Electrical Safety
Your machine is double insulated for safety and requires no earth connection. The operating voltage is
230 V AC, 50 Hz (for non-EU countries 220 V,
240 V as applicable). Only use approved extension
cables. Contact your Bosch Service Center for details.
It is recommended for increased electrical safety to
use a Residual Current Device (RCD) with a tripping
current of not more than 30 mA. Always check your
RCD every time you use it.
WARNING: For safety, it is essential that the mains
plug 15 attached to the machine is fitted to the power
supply cable 17.
The couplings of connection leads must be protected against splashes and the coupling sockets on
the leads must be made of rubber or coated with rubber.
Fixing means for the connection leads must be used.
The connection lead must be inspected for signs of
damage at regular intervals and may only be used if
in perfect condition.
If the supply cord is damaged, it must be replaced by
a Bosch Service Centre.
Extension cords/leads should only be used if they
comply with H05VV-F or H05RN-F types.
Products sold in GB only: Your machine is fitted with
an approved 13 A (BS 1363/A) electric plug and is
protected by a 13 A fuse (ASTA Approved to
BS 1362).
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted
in its place by an authorized customer service agent.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted
into a 13 A socket elsewhere.
17 • F 016 L70 621 • 09.11
Do not connect the machine to the mains
socket before it is completely assembled.
A Mounting the Cutting Guard
Place the cutting guard 10 on the trimmer head 7.
➊ Hook the guard onto trimmer head and push until
secure fitting.
➋ Push rear of guard until secure (click).
Mounting the Wheels
(ART 30/3000 COMBITRIM only)
B1 Fit the wheels 11 onto the shaft 6.
B2 Fit the bolt 19 and the wingnut 18.
Note: The position of the wheels can be adjusted by
loosening the wingnut 18 and moving to the desired
position.
B3 The wheels can be moved up and down the
shaft 6 depending on the height of cut required.
Adjustment
C Using Adjustable Handle
The adjustable handle 4 can be set in various positions:
➊ To change the position undo the handle wing
nut 3 and move the adjustable handle 4.
➋ Tighten the handle wing nut 3 securely to fix the
adjustable handle 4 in the adjusted position.
D Adjusting Product Length
➊ Loosen the adjustment collar 5 90°.
➋ Pull the shaft out to increase the height, or push
the shaft in to decrease the height. Re-tighten adjustment collar 5.
E Adjusting cutting head angle:
To change the angle depress the foot pedal 12 and
move the shaft 6 to the desired position.
Release the foot pedal 12.
Adjusting for Edging Mode
F Moving wheels (where fitted):
➊ Loosen wingnut 18.
➋ Twist wheels 11 90° as shown.
➌ Tighten wingnut 18.
G Adjusting cutting head angle:
➊ Depress the foot pedal 12.
➋ Move the shaft 6 to the lowest position. Release
the foot pedal 12.
H Move trimmer head:
➊ Loosen the adjustment collar 5.
➋ Turn the shaft 6 90° to position the trimmer
head 7 for trimming/edging as shown. Re-tighten
adjustment collar 5.
English - 3
F 016 L70 621.book Seite 4 Montag, 30. November 2009 3:03 15
Cutting and Edging
Remove stones, loose pieces of wood and
other objects from the cutting area.
The cutting line continues to rotate for a few seconds after the trimmer is switched off. Allow the
motor/cutting line to stop rotating before switching “on” again.
Do not rapidly switch off and on.
Switching On and Off
Press switch 1 and hold depressed. Release
switch 1 for switching off.
I Cutting Grass
Move the trimmer left and right, keeping it well away
from the body.
The trimmer can efficiently cut grass up to a height
of 15 cm. Cut taller grass in stages.
Remove the wheels when cutting long grass
(ART 30/3000 COMBITRIM only).
Cutting Very Long Grass/Weeds
The product is supplied with Extra Strong Line and a
fixing spool, fit as described in spool maintenance.
Fitting the Extra Strong Line for very long tough conditions will improve the performance and give better
results.
J Trimming Edges
Guide the trimmer along the edge of the lawn. Do not
allow the cutting line to contact paved surfaces,
stones or garden walls, since this will wear the line
rapidly.
For better control use the plant protector 9
(ART 30/3000 COMBITRIM only – available as an
accessory for ART 23/26/2300/2600 COMBITRIM)
as a guide.
K Cutting Around Trees and Bushes
Carefully cut around trees and bushes so that they
do not come into contact with the cutting line.
Plants can die if you damage the bark.
For better control use adjustable handle and use the
plant protector 9 (ART 30/3000 COMBITRIM only –
available as an accessory for ART 23/26/2300/2600
COMBITRIM).
Feeding the Line
Do not feed and cut off excess line in edging position (see figure J). Feed button 20
may become hot.
The rotating line can wear or break. You will notice
when the motor runs without load and no grass is
cut.
18 • F 016 L70 621 • 09.11
L While operating the trimmer press the ground or
a solid surface, then release (necessary pressure
approx. 3 kg). This action will allow the feed button 20 to release the line out. The spool will release
approx. 4 cm of line per action.
When the line breaks off completely, feed twice to
regain the full cutting circle.
M If the line is exceeding the maximum cutting circle it will be cut by the blade 24 integrated in the cutting guard 10.
Maintenance
Stop and remove plug from the power supply.
Note: To ensure long and reliable service, carry out
the following maintenance regularly.
Regularly check for obvious defects such as loose
fixings, and worn or damaged components.
Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or
repairs before using.
If the trimmer should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorized customer service agent
for Bosch garden products.
For all correspondence and spare parts orders, always include the 10-digit part number (TYP) from
the nameplate of the machine!
Spool Maintenance
Stop and remove plug from the power supply.
M Replacing the Line Spool
Hold the spool plate 23 in position.
Turn the spool cover 21 counter-clockwise and remove.
Take the empty spool 25 out from the spool cover.
Thread the line of the new/refilled spool through the
eyehole 22 and place the spool in the spool
cover 21.
Pull approx. 9 cm of line out of the spool.
Place spool with cover 21 on the spool plate in the
correct position (bayonet fastening), press down and
turn fully clockwise (click).
Fitting Extra Strong Line Spool
Hold the spool plate 23 in position.
Turn the spool cover 21 counter-clockwise and remove.
English - 4
F 016 L70 621.book Seite 5 Montag, 30. November 2009 3:03 15
Place the Extra Strong Line spool 14 on the spool
plate in the correct position (bayonet fastening),
press down and turn fully clockwise (click).
When the Extra Strong Line breaks, us the
O
above procedure to remove the spool and fit the Extra Strong replacement Line 13 as shown to the
spool.
Replacement Extra Strong Line can be stored on the
product as shown in main figure.
Refilling Line
Take out the spool 25 as described above.
Press the cover ring 27 together, push it forward and
detach over the smaller diameter of the spool.
Cut off approx. 8 m line from the refill roll. Press one
end into the notch of the spool so that it stands out
approx. 4 mm.
Wind on the line tightly and in orderly layers in arrow
direction.
Thread the line’s end through the slot 26 in the cover
ring 27 from the inside.
Keep the line tight and slide the cover ring 27 over
the smaller diameter of the spool.
N
Build in the spool as described above.
Note: Only use Bosch replacement line. It has been
developed specially for improved cutting and feeding performance. The use of other line will lead to a
deterioration in performance.
After Trimming/Storage
Stop and remove plug from the power supply.
Clean the exterior of the machine thoroughly using a
soft brush and cloth. Do not use water, solvents or
polishes. Remove all grass and debris, especially
from the ventilation slots 8.
Turn the machine on its side and clean the cutting
guard 10 inside. If grass cuttings are compacted, remove with a wooden or plastic implement.
Hang the cable on the hook provided. DO NOT
wrap/loop the supply/extension cable around the
hook and the guard together – this will cause the cable to be in contact with the guard blade which can
damage the cable. ONLY hang the cable on the
hook provided.
Fault Finding
The following table gives checks and actions that you can perform if your machine does not operate correctly.
If these do not identify/remedy the problem, contact your service agent.
Warning: Switch off and remove plug from mains before investigating fault.
Symptom
Possible Cause
Remedy
Machine fails to operate
Power turned off
Mains socket faulty
Extension cable damaged
Fuse faulty/blown
Turn power on
Use another socket
Inspect cable, replace if damaged
Replace fuse
Machine functions
intermittently
Extension cable damaged
Inspect cable, replace if damaged
Contact Service Agent
Contact Service Agent
Machines internal wiring damaged
Machine labours
Grass too high
Cut in stages
Machine is not cutting
Line too short/broken off
Feed the line manually/automatically
Line can not be fed
Spool empty
Line inside the spool entangled
Replace the spool
Inspect the spool, rewind if necessary
Line keeps breaking
Line inside the spool entangled
Trimmer used incorrectly
Inspect the spool, rewind if necessary
Only trim with the tip of the line, avoid
stones, walls and other hard objects.
Feed the line regularly to maintain full
cutting width.
19 • F 016 L70 621 • 09.11
English - 5
F 016 L70 621.book Seite 6 Montag, 30. November 2009 3:03 15
Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According to the European Directive
2002/96/EC on waste electrical and
electronic equipment and its incorporation into national law, products that
are no longer suitable for use must be separately
collected and sent for recovery in an environmentally-friendly manner.
After-Sales Service and
Customer Assistance
Our after-sales service responds to your questions
concerning maintenance and repair of your product
as well as spare parts. Exploded views and information on spare parts can also be found under:
www.bosch-pt.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty.Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
20 • F 016 L70 621 • 09.11
Inside Australia:
Phone: +61 (01300) 307 044
Fax: + 61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Declaration of Conformity
Measured sound values determined according to
2000/14/EC (1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product
are: sound pressure level 85 dB(A); sound power
level 95 dB(A). Uncertainty K=1 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60335:
Vibration emission value ah =3.5 m/s2, Uncertainty
K=2 m/s2.
We declare under our sole responsibility that the
product described under „Technical data“ is in conformity with the following standards or standardization documents: EN 60335 according to the provisions of the directives 2004/108/EC, 98/37/EC (until
28 Dec 2009), 2006/42/EC (from 29 Dec 2009),
2000/14/EC.
2000/14/EC: Guaranteed sound power level
96 dB(A).
Conformity assessment procedure according to Annex VI.
Equipment category: 33
Notified body: SRL, Sudbury, England, Nr. 1088
Technical file at: Bosch Lawn and Garden Ltd., PTLG/EAE, Stowmarket, Suffolk IP14 1EY, England
Leinfelden, 21.10.2009
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
Robert Bosch GmbH, Power Tools Division
Subject to change without notice
English - 6