Maytag LAT8826 Installation manual

AUTOMATIC WASHER
Welcome
...................................................
Safety Instructions
Controls
Special
1
................................ 2
At A Glance ........................ 3-5 "
Features ..................................... 6
Operating
_ps ........................................ 7
Care and Cleaning ................................. 8
Storing
the Washer ............................... 8
Water Use .................................................
8
Before You Call ................................. 9-10
Warranty .................................... Back Page
Models: LAT9706 • LAT8826 • LAT9757 • LAT8816
Welcome
.....................................................................
Welcome and congratulations
on your
purchase of a
Consumer Rated No.l Maytag
Washer! Your complete satisfaction is very important to us.
2) Have proof of original date of purchase.
Please attach your sales receipt here.
Read this manual for best
results. It contains instructions
to acquaint you with proper
operating and maintenance procedures.
_
_.__
In addition you will find a Laundering Tips guide
packed with your washer. It contains information on recommended laundering procedures, stain removal and
special laundering situations.
go wrong, we suggest consulting the
"Before You Call" section in the back of this
Save time and money. If something should
book. It is designed to help you solve basic
problems before consulting a servicer.
However, should you need assistance, it is helpful to:
1) Have complete model and serial number identification of your washer. This is located on a data plate on the
top edge of the control panel. Record these numbers
below for easy access.
Model Number
For additional questions, please contact us:
Serial Number
Maytag Consumer Information
One Dependability Square
Newton, Iowa 50208
(Mon.-Fri., 8am-5pm Central Time)
(515)
791-8911
Internet:
http://www.maytag.com
For service and warranty information, see back 1c
NOTE: In our continuing effort to improve the qu
our appliances, it may be necessary to make cha_
the washer without revising this guide.
i ....
Important
• /5
i :¸
Safety Instructions ....................................
,_ WARNIN6 -- To reduce the risk of fire, explosion, electric shock, property damage or injury
to persons when using your appliance, follow basic precautions, including the following:
1. Read all instructions before using the appliance,
been used for such a period, before using a wash-
2. As with any equipment using electricity and having
moving parts, there are potential hazards. To use
this appliance safely, the operator should become
familiar with the instructions for operation of the
appliance and always exercise care when using it.
ing machine or combination washer-dryer, turn
on all hot water faucets and let the water flow
from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame
during this time.
3. Do not install or store this appliance where it will be
exposed to the weather.
4.
5.
7. Do not reach into the appliance if the tub or agitator
is moving.
Install and level washer on a floor that can support
the weight.
8. Do not allow children to play on or in the appliance.
Close supervision of children is necessary when the
appliance is used near children.
This appliance must be properly grounded. Never
plug the appliance cord into a receptacle which is
not grounded adequately and in accordance with
local and national codes. See installation instructions for grounding this appliance,
9. Do not tamper with controls.
10. Do not repair or replace any part of the appliance or
attempt any servicing unless specifically recom-
6. To avoid the possibility of fire or explosion:
mended in published user-repair instructions that
you understand and have the skills to carry out.
a. Do not wash items that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable
or explosive substances as they give off vapors
that could ignite or explode. Hand wash and line
dry any items containing these substances,
I 1. Unplug power supply cord before attempting to service your washer.
12. The agitator should not be removed. If the agitator
is removed, it must be replaced by pushing down
completely and the locking screw tightened before
Any material on which you have used a cleaning
solvent, or which is saturated with flammable liquids or solids, should not be placed in the washer
the washer is operated.
13. Store laundry aids and other material in a cool, dry
place where children cannot reach them.
until all traces of these liquids or solids and their
fumes have been removed,
These items include acetone, denatured alcohol,
gasoline, kerosene, some liquid household clean-
14. Do not wash or dry items that are soiled with vegetable or cooking oil. These items may contain some
oil after laundering. Due to the remaining oil, the
fabric may smoke or catch fire by itself.
ers, some spot removers, turpentine, waxes and
wax removers.
b. Do not add gasoline, dry-cleaning solvents, or
15. Do not use chlorine bleach and ammonia or acids
(such as vinegar or rust remover) in the same wash.
Hazardous fumes can form.
other flammable or explosive substances to the
wash water. These substances give off vapors
that could ignite or explode,
16. Do not machine wash fiberglass materials. Small
particles can stick to fabrics washed in following
loads and cause skin irritation.
c. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not
17. Before the appliance is removed from service or discarded, remove the door to the washing compartment.
Save These Instructions
2
Controls At A Glance
Step
Select Cycle
...............
............
(Features may vary according to model.)
Press the control knob in and turn clockwise
Pull the knob out to start the washer.
to the desired cycle.
SENSI-CARE
for Hand Washables
is
designed for items labeled "hand washable." The washer alternates between
periods of delicate wash and soak.
Cycles available:
PRESOAK (select models) - soaks
load for approximately 8 minutes
to help remove soils. The washer
moves directly into a Regular
Heavy cycle.
OR
NORMAL - approximately 10 minutes of
wash time
LIGHT - approximately 6 minutes of wash
time
SUPER WASH (select models) extends Regular cycles by providing up to 24 minutes of wash time
for very soiled durable loads.
,?:
_'
c
SENSI-CARE
forHand Washables
extra OFF
spin
o_.0_
_
presoak
REGULAR /
DELICATE
NORMAL
¢
T
LIGHT / QUICK
LIGHT
NORMAL
OFF
rinse
spin
e,
soin
ooo,aow,
EASYCARE /
LIGHT
HEAVY
PERMANENT PRESS
approximately 10-14 minutes
of wash time
• (NORMAL) - approximately
minutes of wash rime
OFF
SOAK
ONLY
EASY CARE/PERMANENT
PRESS
is designed to minimize wrinkles with
a cool-down spray rinse following the
wash. Cycles available:
HEAVY-
exlra
OFF
7-9
SOAK ONLY - soaks
heavily-soiled
or
stained
items
as
desired. The user
then advances the
control knob into a
wash cycle or spin
and drain. (Overnight
soaking is not recommended.)
LIGHT - approximately 5-6 minutes of
wash time
3
REGULAR/DELICATE
cy¢
share the same portion of
control knob. For regular fabr
select a cycle and press a 1Lt
ULAR WASH/SPIN
SPE
button. For delicate
fabr
select a cycle and press a DE
CATE WASH/SPIN SPEED I
ton. (See page 5 for deta
information.) Cycles availabl
EXTRA HEAVY (select mud
- approximately 16-18 min
of wash time
HEAVY - approximately
minutes of wash time
1_
NORMAL - approximately 1(
minutes of wash time
LIGHT/QUICK - approximz
7-9 minutes of wash time
A
Step _
Select Water Level
(Features may vary according to model.)
INFINITE SLIDE CONTROL - (select models) move the
slide lever up or down to the desired setting or any point in
between. If more water is needed once the fill is complete,
move the lever up to reset and then to the proper setting.
INFINITE WATER LEVEL
.......
/
PUSH BUTTON CONTROL - (select models) press the
appropriate button to match the load size to the water level,
WATER LEVEL
;ETTING
LOAD SIZE
'
reset !
SUPER,
LARGE
i
Super
• *
Large
e,,
MEDIUM" !
3/4 - Full
•e,
,,
1/2 - 3/4
Full
e**
•,,e
eo
,**
Medium
1/3- 1/2 Full
Small (select models)
1/3 Full
Mini
1/4 Full
REMEMBER:
oo
SMALL
i
MINI !
: ::
Items must circulate freely for best results.
A
Step
,_ Select Water Temperature
Press the appropriate button to select the wash and rinse temperatures. Follow the garment care label for best results. Use
the chart below as a guide.
WASHRINSE TEMPS
Hot/Cold
• o
•
•o
•
oo
•o
...................................
Warm/Warm
Warm/Cold
............................
Cold/Cold
HOT
COLD
LOAD TYPE
White and heavily soiled,
color-fast items
•••o
•
••*
•
•••
•
ee*
WASH / RINSE TEMP
••*
WARM
WARM
Delicate items
Moderately soiled,
colored items; most Easy
Care/Permanent Press items
Brightly colored, lightly
soiled items; washable
woolens
REMEMBER: In wash water temperatures below 65° IS,deter.
gents do not dissolve well or clean well. Care labels define cold
water as up to 85 ° F.
4
WARM ,,
COLD
GOLD
GOLD
A
Step
_#_
Select
Options
(if desired)
Press the appropriate button(s) to select one or more options.
OPTION
USE
OPTIONS
Provides additional rinse at the end
Extra
of the cycle to more completely
Rinse
remove laundry additives, suds, perfumes,
etc.*...+ +o+. .++. q+**+ +..++ t+*** +.. ++
, i+**+
..++ +***
Removes more water from absorbent
EXTRA
RINSE _
Spin
loads like bath towels. (Not available
with SENSI-CARE
cycle.)
EXTRA :+
SPIN
Energy
Saver
Restricts hot water use to save water
heating costs. Select WASH/RINSE
TEMP desired, plus press Energy
ENERGY
SAVER
Saver button. (select models)
.............................
Cancel
Press button to cancel and reset any
CANCEL
OPTIONS
• . o++**+
+..
_+++1
Extra
Options
i+++
Step
,*++
.+.
of the above options. (select models)
++**
++*
.+++*
Q*,
Select WashSpin
+++
.1.
Speeds
Press the appropriate button to select the wash and spin
speeds to fit the fabric type.
WASh/SPIN SPEED
DESIGNED FOR
Regular/Fast
Sturdy water
fabrics
needing maximum
extraction
..................................................................
Sturdy fabrics needing slower
Regular/Slow
spin speed because of wrinkling
..................................................................
Delicate fabrics needing slower
Delicate/Slow
spin speed because of construction
++,+w+,,++++.+,,*.+**+..,,+++..w,,B+m+_+oo+++++*_+++*_t_+++_++
Step 0
Start
Washer
• Add detergent.
• Add load and close lid.
• Pull out control knob to start.
5
WASH
REGULAR _+.
FAST
REGULAR
SLOW
DELICATE
SLOW
/ SPIN
SPEED
Special
Indicator
Features ..................................................
Lights
0 SOAK
• SOAK - lights during a soak cycle.
• WASH/RINSE - lights to indicate the washer is in
a wash or rinse portion of the cycle.
• ON - lights whenever the washer is running.
O
WASH/
RINSE
O
ON
Bleach Dispenser
The dispenser automatically dilutes liquid chlorine
bleach before it reaches your wash load. To use, follow
these steps:
1, Measure liquid chlorine bleach carefully, following
the instructions on the bottle.
2. Add the bleach to the dispenser before adding the
load. Avoid splashing or over-filling the dispenser.
NOTE:
• Never pour undiluted liquid chlorine bleach directly
onto the load or into the wash tub. It is a powerful
chemical and can cause fabric damage, such as tearing or color loss, if not used properly.
Pour liquid chlorine bleach into
bleach dispenser.
• If you prefer to use color-safe, non-chlorine bleach,
pour it into the wash tub with your detergent. Do not
pour non-chlorine bleaches into the bleach dispenser.
Fabric Softener
Dispenser
This dispenser automatically releases liquid fabric softener at the proper time during the cycle. To use, follow
these steps:
1. Pour liquid fabric softener into the dispenser using
the amount recommended on the package.
2. Add warm water to the dispenser until it reaches the
MAX line.
NOTE:
• Do not stop the washer during the first spin. This will
cause the dispenser to empty too soon.
• Never pour fabric softener directly on the load. It will
leave spots and stains.
• Use the dispenser for liquid fabric softeners only.
Clean the area in and around the dispenser frequently
with hot water, detergent and a soft brush.
Pour liquid fabric softener into cup and
dilute with warm water.
6
Operating
"rips ....................................................
For detailed information on sorting, pretreating
stains, etc., see the enclosed Laundry Tips pamphlet.
Loading
• Put dry, unfolded clothes loosely in the tub, up to
Detergent
• Use either liquid or granular laundry detergent. For
top row of holes for a maximum load.
• Do not wrap large items like sheets around the ag
tor.
best results, be sure detergent is added to the
washer
the load and be sure wash water
is aboveBEFORE
65° F.
• Mix large and small items for best circulation. W
bulky items like blankets separately.
• Use the correct amount of detergent for the load size,
soil level and water conditions. Use more detergent if
you have hard water and very soiled loads,
If you have soft water or a lightly soiled load, use less
• When laundering permanent press items or item_
delicate construction, washable woolens or loos
knit items, never use less than the MEDIUM w_
level setting. This will minimize shrinkage, wrinkl
and pulling of seams.
detergent. (See manufacturer's instructions.)
• Wipe up any detergent spills on the washer,
Additional
•
For best results, add the detergent to washtub bef
adding the load.
7ps
• If the washer stops during the spin, it may be due to
an unevenly distributed load. If this happens, push in
the control knob, open the lid, redistribute the load,
close the lid and pull out the control knob. The spin
• This washer is designed so that it will not agitate
spin when the lid is open. It will, however, fill w
the lid open so water is available for pretreating sta
or diluting fabric softener.
will resume at the point it was interrupted.
• The washer will pause briefly throughout each cycle,
These pauses are normal,
• If you open the lid during a cycle, the washer
stop. When the lid is closed and the control kn
pulled out, the washer will continue the cycle at 1
point it was interrupted.
"7
i _iJi _: i_iiI¸¸_
ii::;
<i i_ii::!__
'_ ':_:
i:/_
_:
>
Care and --Cleaning ...................................o_,_
.........
_...........
Turn off the water faucets after finishing the day's washing. This will shut off the water supply to the washer
and prevent the unlikely possibility of damage from
Interior - hard water deposits may be removed, if
needed, using a recommended cleaner labeled washer safe.
escaping water.
Use a soft cloth to wipe up all detergent, bleach or other
spills as they occur,
Lint Filter - it is self-cleaning and requires no maintenance. The filter is located under the agitator on the
bottom of the washtub. During the wash and rinse
portion of the
cycle, lint is collected on the illter. Then during
the spin and
drain the filter is
cleaned automatically.
Clean the following as recommended:
Control Panel - clean with a soft, damp cloth and glass
cleaner. Do not use abrasive powders or cleaning
pads.
Cabinet - clean with soap and water followed with an
appliance wax if desired,
Storing
the Washer ....................
......... ......................
Washers can be damaged if water is not removed from
hoses and internal components before storage. Prepare
the washer for storage as follows:
• Advance the cycle control knob to Spin and lower the
drain hose to eliminate any water that may be in the
drain hose.
• Select the NORMAL cycle for regular fabrics and add
one cup of chlorine bleach or white vinegar to a full
load of water without clothes.
Run the washer
through a complete cycle.
• Disconnect the washer from the electrical supply and
leave the washer lid open to let air circulate inside the
tub.
• Turn the water faucets off and disconnect the inlet
hoses.
Water
Use .... ...........,............................................................ ....
REGULAR CYCLE
Super
t,.,oiiowtell,
PERMANENT PRESS CYCLE
Approx. 40 gallons
(33 Imperial gallons; 151 liters)
Super
mO_,OIO_.*_I,,OQ*O,IIO._O.O.Q*.Q.II._*.
._,,O.,m*QI,•
Approx. 43 gallons
(36 Imperial gallons; 163 liters)
i.,,*_•,•I.,*,.O_*,.O*O.*_••,•OD.I••,.*
Large
Approx. 36 gallons
(30 Imperial gallons; 136 liters)
Large
Approx. 39 gallons
(32 Imperial gallons; 148 liters)
Medium
Approx. 32 gallons
(27 Imperial gallons; 121 liters)
Medium
Approx. 35 gallons
(29 Imperial gallons; 132 liters)
Small
Approx. 28 gallons
(23 Imperial gallons; 106 liters)
Small
Approx. 31 gallons
(26 Imperial gallons; 117 liters)
Mini
Approx. 24 gallons
(20 Imperial gallons; 91 liters)
Mini
Approx. 27 gallons
(22 Imperial gallons; 102 liters)
N
Before You Call ................................................
For problem laundry solutions (i.e. fabric damage, residue, tangling) and special laundry care pro_
dures, see the enclosed Laundry Tips pamphlet•
Check
these
)oints
• Plug cord into live electrical outlet.
• Check fuse or reset circuit breaker.
• Turn the control knob to proper cycle and pull knob out to start the washer
If equipped with buttons, be sure they are fully depressed.
• Turn both faucets on fully.
• Straighten inlet hoses.
• Disconnect hoses and clean screens. Hose filter screens may be plugged.
Won't Fill
JQ
too
*•J
*o•
ott
!i_'_!,!iii
i
Won't Agitate
if your washer...
,Q
•
•
•o
***
too
••o
**l
too
•oJ
•oQ
*oo
•o
••o
•••
*•
••
•to
•o
It.too
*llo
•to,
ool
• Check fuse or reset circuit breaker.
• Turn the control knob to proper cycle and pull knob out to start the washer.
If equipped with buttons, be sure they are fully depressed.
• Close lid and pull knob out to start the washer. For your safety, washer will
not agitate or spin unless the lid is closed.
• The washer is equipped with a lid switch failure detector. If the lid switch
should malfunction, the detector will stop operations for your safety. Call for
service.
<.
Won't Spin
or Drain
• •oo..
*•....
• •..
• o...•o..
• Unevenly distributed load. Redistribute the load, close the lid and pull knob
out. Check for leveling. Be sure water level is acceptable for load size.
• Check fuse or reset circuit breaker.
• Straighten drain hoses. Eliminate kinked hoses. If there is a drain restriction,
call for service.
• Close lid and pull knob out to start the washer. For your safety, washer will
not agitate or spin unless the lid is closed.
• Suds lock - caused by too much suds. Rewash without detergent. Use correct amount of a low-sudsing detergent.
• The washer is equipped with a lid switch failure detector. If the lid switch
should malfunction, the detector will stop operations for your safety. Call for
service.
• * • ...oo..•o...
• •..•oo.o•oo.o•oo.
• • • • .o•oo.ooo.._•l..
9
*• • ..•oQ.•oo..*oo.•*
• •..
• •..
,oo..
•o•..••o...*o..,
•
Check these
}oints
if ,our washer...
IZ
• Unevenly distributed load. Redistribute the load, close the lid and pull knob
out. Check for leveling. Be sure water level is acceptable for load size.
• Plug cord into live electrical outlet.
• Check fuse or reset circuit breaker.
• Turn the control knob to proper cycle and pull knob out to start the washer. If
Stops
•
*
•
•
equipped with buttons, be sure they are fully depressed.
• Close lid and pull knob out to start the washer. For your safety, washer will
not agitate or spin unless lid is closed.
• This may be a pause or soak period in the cycle. Wait briefly and it may start.
• The washer is equipped with a lid switch failure detector. If the lid switch
should malfunction, the detector will stop fill operations for your safety. Call
for service.
•
*
•
.,
•
•
•
•
•
Leaks Water
••
•
.•
..
•
•
•
•
••
..
•
...•
•
..
.
.*
•
•
•
*
..
*
**
*
..
* **
*
* •
.*
•
Make sure hose connections are tight.
Make sure end of drain hose is correctly inserted and secured to drain facility.
Avoid extended soaking - soak for 30 minutes or less.
Avoid overloading.
• Be sure washer is leveled properly as outlined in installation manual.
• Weak floors can cause vibration and walking.
• Be sure rubber feet are installed on leveling legs.
ls Noisy
• •..•..
..
•
..
•
•
•,
.
•
•
•
•
•
•
•
*•
•
..
•
•
•
*
•
•
•
••
•
..
*
•.
•
..
••.
.
•
•*
.
•,
• Turn both faucets on fully.
• If equipped with a temperature selector knob, be sure it is set directly on a
temperature setting and not between settings.
• Make sure temperature selection is correct.
• Make sure hoses are connected to correct faucets and inlet connections. Be
sure water supply is regulated correctly. Flush water line before filling
washer,
• Check the water heater. It should be set to deliver a minimum 120°F (49°C)
hot water at the tap. Also check water heater capacity and recovery rate.
• Disconnect hoses and clean screens. Hose filter screens may be plugged.
Fills with
the Wrong
Temperature
Water
• ...
Cycle Selector
Knob Advances
Through
"OFF"
•
• ..
• ..
• ..
•
•
•
•
.*
•
••
•
..
•
.
•
•
•
•
..
.
.•
•
.*
•
..
•
..
•
•
•
•
•
•
•
..
¢
•
•
•
•
•
•
•
•
• Extra rinse option is selected
•
•
•
.•
•
..
•
= •
•
•
..
•.
..
•
•
•
..•
•.•
•
•.
•
..
Forfurther help, call Maytag Customer Assistance: U,S. 1-800.688.9900 or Canada 1-800-688-2002
U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1.800-688-2080.
10
•
•
Automatic
Washer Wa rranty
Full One Year Warranty
For one (1) year from the date of original
retail purchase,
any part which fails in normal home use will be
repaired or replaced free of charge.
Limited
Parts Warranty
After the first year from the date of original retail purchase through the time periods listed below, the designated parts which fail in normal home use will be repaired or replaced free of charge for the part itself, with the
owner paying all other costs, including labor.
Second Year - All parts.
Third through
Fifth Year - The drive motor.
Third through Tenth Year - All parts of the transmission assembly.
Additional
Limited Warranty Against Rust
Should an exterior cabinet, including the top, lid, and baseframe, rust during the five year period starting from
the date of original retail purchase, repair or replacement will be made free of charge during the first year. After
the first and through the fifth year, repair or replacement will be made free of charge for the part itself, with the
owner paying all other costs, including labor.
This full warranty and the limited warranties apply when the appliance is located in the United States or Canada.
Appliances located elsewhere are covered by the limited warranties only, which include parts which fail during
the first year.
To Receive Warranty Service
To locate an authorized service company in your area, contact the Maytag dealer from whom your appliance was purchased
or call Maytag Customer Service. Should you not receive satisfactory warranty service, call or write:
Maytag Customer Assistance
c/o Maytag Customer Service
EO. Box 2370
Cleveland, TN 37320-2370
US
1-800-688-9900
CANADA
1-800-688-2002
U.S. customers using TTY for deaf, bearing impaired or speech impaired, call 1-800-688-2080.
When contacting Maytag Customer Service be sure to provide the model and serial numbers of your appliance, the name and
address of the dealer from whom you purchased the appliance and the date of purchase.
This Warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
Shouldyou still have a problem, write to: Major Appliance Consumer Action Program (MACAP), 20 North Wacker Drive,
Chicago, Illinois 60606, MACAP is an industry sponsored but independent group of consumer experts who receive and act on
complaints from appliance owners.
NOTE:
When writing about an unsolved service problem, please include the following information:
(a) Your name, address and telephone number;
(b) Model number and serial numbers (found on top edge of control panel) of your appliance;
(c) Name and address of your dealer and date the appliance was bought;
(d) A clear description of the problem you are having;
(e) Water hardness, detergent brand and amount, water temperature and cycle used.
MAYTAG
FormNo.545CMA
PartNo.6 2301280
• One Dependability Square
__i
• Newton, Iowa 50208
_i_!. i_,'i_
_"http ://www. rnaytag, co m
JN
kithoU.S.
Automatic
Washer
Warranty
.............................
Full One Year Warranty
For one (1) year
from the date of original
repaired
or replaced
Limited
Parts Warranty
retail purchase,
any part which fails in normal
home
use will be
free of charge.
After the first year from the date of original retail purchase through the time periods listed below, the designated parts which fail in normal home use will be repaired or replaced free of charge for the part itself, with the
owner paying all other costs, including labor.
Second Year - All parts.
Third
through
Fifth Year - The drive motor.
Third
through
Tenth Year - All parts of the transmission
Additional
Limited
Warranty
Against
All parts of the solid state controls
(if so equipped).
assembly.
Rust
Should an exterior cabinet, including the top, lid, and baseframe, rust during the five year period starting from
the date of original retail purchase, repair or replacement will be made free of charge during the first year. After
the first and through the fifth year, repair or replacement will be made free of charge for the part itself, with the
owner paying all other costs, including
labor.
This full warranty and the limited warranties apply when the appliance is located in the United States or Canada.
Appliances located elsewhere are covered by the limited warranties only, which include parts which fail during
the first year.
To Receive Warranty Service
To locate art authorized service company in your area, contact the Maytag dealer from whom your appliance was purchased
or call Maytag Customer Service. Should you not receive satisfactory warranty service, call or write:
Maytag Customer Assistance
c/o Maytag Customer Service
P.O. Box 2370
Cleveland, TN 37320-2370
US
1-800-688-9900
CANADA
1-800-688-2002
When contacting Maytag Customer Service be sure to provide the model and serial numbers of your appliance, the name and
address of the dealer from whom you purchased the appliance and the date of purchase.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Shouldyou still have a problem, write to: Major Appliance Consumer Action Program (MACAP), 20 North Wacker Drive,
Chicago, Illinois 60606, MACAP is an industry sponsored but independent group of consumer experts who receive and act on
complaints from appliance owners.
NOTE:
When writing about an unsolved service problem, please include the following information:
(a) Your name, address and telephone number;
(b) Model number and serial numbers (found on top edge of control panel) of your appliance;
(c) Name and address of your dealer and date the appliance was bought;
(d) A clear description of the problem you are having;
(e) Water hardness, detergent brand and amount, water temperature and cycle used.
MAYTAG • One Dependability
Form No, 522CMA
Part No. 6 2166840
,
,
•
Square
° Newton, Iowa 50208
htt p://www.m
aytag.co
m
JN
Litho U.S.A.