Whirlpool AWG 652/WP - SERVICE User`s guide

Performance Parts
SERVICE TOOL CATALOG
for
Truck/Trailer D Container D Transport A/C D Marine
62-03213 Rev J
Service Tool Catalog
INTRODUCTION
This service tool catalog identifies service tools used to perform service on transport
refrigeration equipment manufactured by Carrier Transicold. Service tools included in this
catalog are recommended tools that are considered necessary for proper service.
This catalog is broken down into major tool categories listed on page i. Also, this catalog
includes both a pictorial and descriptive reference to most tools listed. This is intended to make
it as simple as possible to find the service tools required.
ORDERING INSTRUCTIONS
All orders and inquiries for parts must include:
D Part number
D Description of part as shown
D Quantity required
Address all correspondence for parts to the following address:
Carrier Transicold Division
Performance Parts Group, TR-20
P.O. Box 4805
Syracuse, NY 13221
or fax to : (315) 432-3778
How to use this manual
Please take a few minutes to read this page. It explains the content and structure of this manual,
which will make it easier to find the tools you need.
Section 1 Compressor & Clutch
This section contains tools used on compressors and clutches.
Section 2 Electrical
This section contains electrical tools.
Section 3 Engine
This section contains tools used on engines.
Section 4 Fittings
This section contains fittings.
Section 5 General Tools
This section contains general tools.
Section 6 Refrigeration
This section contains Refrigeration tools.
Section 7 Shop Supply, Cleaners and Chemicals
This section contains general Shop Supply.
Index
Alphabetical and Numerical Index.
i
Compressor and Clutch
Description
Part Number
Clutch Tools
WRENCH, SPANNER FOR CLUTCH
ARMATURE (BUS)
07-00240-01
Spanner wrench for holding the armature plate on
clutches. The holding pins are adjustable for use
on different industry clutches, including housingmounted.
BEARING DRIVER, FOR HOUSING MOUNTED
CLUTCH (BUS)
07-00241-00
Rotor installation tool for housing-mounted
clutches. Used to “tap” the inner race onto the
compressor hub.
SOCKET, SPANNER NUT LARGE W/ GREASE
FITTING (BUS)
07-00242-01
Socket for 3.0” spanner nut on housing-mounted
clutches. Used on the following spanner nuts:
34-01301-TWIN PORT COMP, 34-06083-00, and
34-01161-00.
SOCKET, SPANNER NUT SMALL WITH OUT
GREASE FITTING (BUS)
07-00242-02
Socket for 2.75” spanner nut on housing-mounted
clutches. Used on the 34-01162-00 spanner nut.
BOLT, CLUTCH REMOVAL, 7/8-14X4”
07-00381-00
Used to remove the clutch on 05G compressors
CLUTCH TOOL, VARIABLE SPEED
COMPRESSOR DKS-26 (BUS)
Clutch tool for variable speed DKS-26
compressor.
1--1
AC101-707
Compressor and Clutch
Description
TERMINAL BOX TOOL -- SCROLL
COMPRESSOR
Part Number
07-00436-00
Used to remove and replace container unit scroll
compressor terminal box
TRAILER UNIT STANDBY CLUTCH
ADJUSTMENT TOOL
07-00455-00
Used to adjust the standby clutch shoes on trailer
units.
TRAILER UNIT STANDBY CLUTCH BEARING
PRESS TOOL
07-00456-00
Used to press in the bearing on trailer unit
standby clutches.
PLIERS, UNLOADER RING
07-00223-00
Used to install the unloader valves on hot gas
bypass compressors. Pliers compress piston ring.
DIPSTICK, OIL (SANDEN COMPRESSOR)
07-00257-00
Used on Sanden compressor for checking oil
level.
PLIERS, CRIMPING, 06D TERMINALS
07-00263-00
Used to crimp the motor leads into the terminal
block on 06D compressors for Rail, Container,
Marine, and Trailer applications.
VISE GRIP HOLDER
07-00264-00
Used for holding motor leads when replacing a
terminal block on 06D compressors.
WRENCH, (SPECIAL) COMPRESSOR OIL PAN
Used to tighten compressors base plate mounting
bolts with compressors installed.
1--2
07-00267-01
Compressor and Clutch
Description
INSTALL TOOL, TK SHAFT SEAL
Part Number
07-00388-00
Used to install the 20-22-778 one inch shaft seal
on TK compressors.
PULLER, SEAL END MAIN BEARING (5F and
5H COMPRESSORS)
07-00346-00
SLEEVE PULLER (5F COMPRESSORS)
07-00394-00
Used to pull the sleeves out of 5F compressor
cylinders
SLEEVE PULLER (5H COMPRESSORS)
07-00395-00
Used to pull the sleeves out of 5H compressor
cylinders
05G SHAFT SEAL TOOL
Used to install new bellows-style shaft seal on the
shaft of an 05G compressor.
1--3
07-00460-00
Compressor and Clutch
Description
05G LIP SEAL INSTALL TOOL
Part Number
07-00471-00
Used to drive new 05G lip seal into the seal cover
plate.
QUICK START, COMPRESSOR
07-00494-00
Kit used to test-start small 115VAC hermetic
compressors up to 5HP. This kit was set up for
use with Comfort Pro APU compressors, but will
also work with others if appropriate amperage
fuse is used.
FUSE, RESETTABLE, 20A
07-00494-10
Used in the 07-00494-00 Quick Start kit for
Comfort Pro APU compressors.
NOTE: This fuse was only sized for use on APU
compressors. For all others, check the LRA and
follow instructions.
FILTER, FELT SOCK FOR CLEAN-UP 05G
COMPRESSORS
Filter (suction sock) for cleaning up systems with
solid contaminants. Package of 5.
1--4
58-00869-00
Compressor and Clutch
Description
SOCK ADAPTER FOR YORK COMPRESSOR
Part Number
14-60043-00
Uses 58-04165-00 sock, 42-01159-00 o-rings,
and 42-00288-00 gasket
FILTER, FELT SOCK FOR CLEAN-UP 05K and
YORK COMPRESSORS
58-04165-00
Filter (suction sock) for cleaning up systems with
solid contaminants. Package of 5
KIT, VALVE PAD BLANK-OFF, UNLOADER
HEAD SUCTION CUT OFF
17-13004-00
Cap off plate for two-bolt, 1-3/4” center line
service valves.
KIT, VALVE PAD BLANK-OFF, 4 BOLT 2-1/2”
C/L
17-13006-00
Cap-off plate for four-bolt, 2-1/2” center line
service valves.
KIT, VALVE PAD BLANK-OFF, 2 BOLT 1-5/8”
C/L
17-13008-00
Cap-off plate for two-bolt, 1-5/8” center line
service valves.
KIT, VALVE PAD BLANK-OFF, UNLOADER
HEAD SUCTION CUT OFF
Cap off plate for the piston on suction cut-off
unloading cylinder heads.
1--5
17-21056-00
Compressor and Clutch
Description
KIT, VALVE PAD BLANK-OFF, UNLOADER
HEAD HGBP
Part Number
17-55013-00
Cap off plate for the unloader valve on hot gas
by-pass or suction-cut off unloading cylinder
heads.
AIR COMPRESSOR TOOL KIT
18-00099-40
Tools for rebuilding Container CA unit air
compressor 18-00099.
WRENCH - SIGHT GLASS
This improved tool (redesigned and hardened) is
used to install and remove the oil sightglass on
05G, 05K, 06D, 5D, 05D, 5F, AND 5H
compressors.
07-00450-00
WRENCH, SIGHT GLASS
20-204-244
Sight glass installation tool used on Thermo King
compressors.
1--6
Electrical
Description
Part Number
Tools and Meters
METER, MEGOHMETER
07-00481-00
Also known as a “Megger,” this meter is used to test
motor winding insulation integrity on the Vector
generator. Can also be used to test most motors.
See Instruction Sheet: 98
07-00482-00
CASE, MEGOHMETER
Used with part number 07-00481-00Megohmeter
TEST LEADS, MEGOHMETER
07-00483-00
Used on Megohmeter part number 07-00481-00
MULTIMETER, DIGITAL -- PEN TYPE
07-00262-02
This is a small probe-style multimeter, designed
to be used with one hand. This feature is helpful
when measuring in small, hard-to-get-to areas.
The meter has Data Hold feature that saves the
measurement value on the display for later
reading. Two probe style tips ship with the unit,
1/2’ and 3” long. Meter reads up to 600V AC and
DC.
Voltage: DC
AC
Resistance (Ω):
Diode Test:
340mV, 3.4V, 34V, 340V, 600V
3.4V, 34V, 340V, 600V
340, 3.4k, 34k, 340k, 3.4Μ, 34Μ
Range 0 to 3.4V,Current 1.0mA
MULTIMETER, DIGITAL
This meter allows the technician to analyze
electrical components ranging from basic
devices to highly sophisticated solid state
controllers. It features an analog and digital
display to test changing or stable signals along
with audible continuity. A continuous tone signals
continuity; a beep signals a forward biased diode
or transistor. Test leads and protective holster
included.
2--1
07-00243-10
Electrical
Description
TEST LEADS, (RIGHT ANGLE)
Part Number
07-00243-01
For use with 07-00243-10 meter
MULTIMETER, DIGITAL -- WAVETEK
07-00228-00
A digital multimeter with heavy-duty features for
rugged protection from mishaps and adverse
environments. One single selector switch makes
it easier to use and saves time by enabling you
to go directly to the function and range you seek.
Ranges in AC/DC voltage and current along with
Ohm readings meet all your needs. Case
included.
Voltage:
200mV, 2V, 20V, 200V
1500VDC, 1000VAC
Current:
200μA, 2mA, 20mA
200MA, 2A (n/a 110T, 10A
Resistance (Ω): 200, 2k, 20k, 200k, 200Μ, 20Μ
Diode Test:
Range 0 to 2V
Current 20mA±20%
Temperature
--4°F to +1999°F
KIT, TEST LEADS
07-00230-00
For use with 07-00228-00 meter.
AC CURRENT CLAMP
This accessory extends the AC current
measurement capability of the P/N 07-00228 or
CTD P/N 07-00243 multimeter to 150 amperes
without breaking the circuit under test. The
1000:1 current transformation allows direct
reading in amperes when used with the 200 mA
AC current range of the multimeter.
Accuracy from + 3% (60 Hz) to + 4% (1000 Hz)
2--2
07-00229-00
Electrical
Description
TACHOMETER, LASER, RPM
Part Number
07-00488-00
Used to read RPMs on rotating devices.
STROBE LIGHT
Used to set and check engine and compressor
speed. Can be used to freeze motion of pulleys,
fan blades, etc. This strobe is a replacement for
part number 07-00206-00.
07-00486-00
SIMULATOR PROBE
This probe simulator is a complete compact
simulator for checkout and calibration of RTD
instruments such as the RDWET controller.
There are 11 temperatures for inputs to the
controller. Range: --20_F to 70_F in 10_F
increments
07-00212-00
TEMPERATURE CONTROLLER SIMULATOR
MODULE
07-00226-00
Used with Container units equipped with the
Carrier solid state temperature controller
(analog). The simulator module permits quick
check out of the unit system to isolate a
malfunctioning circuit.
2--3
Electrical
Description
DATAREADER (Container)
Part Number
12-50377-01/2.5
Includes DataReader, battery, and cable
GAUGE CALIBRATION FOR 12-01075-00
TEMP GAUGE
07-00273-00
Used as a calibration standard for the
12-01075-00 digital thermometer used on
Thunderbird and Phoenix Advantage units.
KIT, STATIC DISSIPATE
07-00277-00
A work surface designed to prevent electrostatic
discharge from damaging solid-state electronic
devices and components during service.
STRAP, GROUNDING
07-00304-00
A wrist strap grounding to prevent electrostatic
discharge from damaging solid-state electronic
devices and components during service.
TESTER, MICRO
07-00290-01
This tester is used in place of the standard
Trailer microprocessor to test the circuits and
components the microprocessor control.
(Instruction Sheet 62-90258-00)
2--4
Electrical
Description
TESTER, STEPPER MOTOR DRIVE
Part Number
07-00375-00SV
Used to check and/or operate the stepper motor
on container units and XTC trailer units. This tool
is also used to drive the EVXV open and closed
for service diagnosis during troubleshooting.
INDIVIDUAL HARNESS FOR THE CSMV
(Suction Modulating Valve SMV)
Used on the 07-00375-00SV tester.
07-00375-10
INDIVIDUAL HARNESS FOR THE EVXV
(Electronic Expansion Valve EXV)
07-00375-11
Used on the 07-00375-00SV tester.
EXTRACTOR (EPROM)
07-00297-00
Extractor for EPROM on microprocessors.
INSERTER (EPROM)
07-00298-00
Inserter for EPROM on microprocessors.
40S/50S and 40X/50X MICRO CONNECTOR
PIN TOOL
2--5
07-60090-00
Electrical
Description
EXTRACTOR PIN
Part Number
07-00326-00
Packard connectors.
EXTRACTOR PIN
07-00400-00
Pin extractor for Packard terminals (connector
models Metri-pack 280, Metri-pack 480, Metripack 630, and Metri-pack 800).
EXTRACTOR, PIN (AMP CONNECTOR)
For removal of terminal connector pins from
connectors used with auto-start and
microprocessor harnesses.
TERMINAL TOOL (REMOVING PACKARD
TERMINALS IN THERMISTOR PART
#12-00452-00) -- Advanced Micro
Used to remove the terminals from the
12-00452-00 thermistor connector. Also used on
“CM” small bus products and with weatherpack
terminals (male and female).
EXTRACTOR, ML-2, ML-2i and ML-3
CONNECTORS
Also used on all EM small bus evaporators,
Metri-Pack 150, 280, GT150, GT280, 280
tangless, 280 buss bar, 630 pull to seat, lamp
socket B1 and W3, and Metri-Pack 800 electrical
connectors.
EXTRACTOR, TERMINAL, MOLEX
07-00254-00
07-00387-00
07-00329-00
07-00490-00
Used to remove terminals from Molex connectors
in conjunction with the 07-00489-00 crimper. Tool
is used on main power connector of small bus EM
and CM units .
EXTRACTOR, MINI FIT SR.
Designed to extract male and female mini-fit sr. terminals from their appropriate connectors/housings.
2--6
07-00493-00
Electrical
Description
EXTRACTOR, EPROM, I-30S
Part Number
07-60048-00
Designed to extract male and female mini-fit sr. terminals from their appropriate connectors/housings.
CRIMPER, MOLEX, (AWG-8)
07-00489-00
Used on the #8 wires for the power supply for the
EM/CM product lines. Part number 07-00490-00,
terminal extractor, can also be used.
CRIMPER,MOLEX MINI-FIT (10/12)
07-00491-00
Used on the EM evaporators to crimp the terminals
that go into the Molex connector used on the
speeds wires on EM1, 2, 3, 7, etc.
NOTE: This is the #10-12 AWG crimper.
CRIMPER,MOLEX MINI-FIT
07-00492-00
Used on the EM evaporators to crimp the terminals
that go into the Molex connector used on the
speeds wires on EM1, 2, 3, 7, etc.
NOTE: This is the #8 AWG crimper.
CRIMPER, MICRO PIN
07-00268-00
Crimper for micro pin on Container unit.
CRIMPER, ML-2, ML-2i and ML-3
CONNECTORS
Used with unsealed 150 series connectors and
terminals 16 to 22 gauge, Metri-Pack, and
pull-to-seat. Also used on all EM small bus
evaporators.
CRIMPER, WEATHERPACK
Used with sealed weatherpack connectors and
terminal pins 14 to 20 gauge.
2--7
07-00330-00
07-00370-00
Electrical
Description
CRIMPER, PIN
Part Number
07-00401-00
Terminal crimper for Packard terminals (all-purpose, unsealed, wire terminal applications) for wire
size 20-14 AWG (core and insulation), 10-12 AWG
(core only)
CRIMPER, UNSEALED
Used on Vector generator power leads.
07-00496-00
WIRE CRIMPER, MAC TOOLS
Crimper can be used on various size Packard
and Amp connectors.
MAC TOOLS
PART
NUMBER:
TCT1028
TERMINAL REMOVAL TOOL KIT
07-00397-00
Kit used to remove terminals and reinstall new
crimped terminals Includes all the 07-00397
dash numbers. (-01 through -12)
UNIVERSAL HAND CRIMP TOOL
07-00397-02
Hand crimp tool, Deutsch connectors, and ML-2,
Ml-2i and ML-3 connectors.
TERMINAL REMOVAL TOOL KIT
07-00397-01
Removal tool, Deutsch connectors
REMOVAL TOOL, BLUE
Wire size 16-18 gauge, Deutsch connectors.
Primarily used on Multi-Temp units.
2--8
07-00397-03
Electrical
Description
REMOVAL TOOL, YELLOW
Part Number
07-00397-04
Wire size 12 gauge Deutsch connectors.
Primarily used on Multi-Temp units.
REMOVAL TOOL, GREEN
07-00397-05
Wire size 14-18 gauge Deutsch connectors.
Primarily used on Multi-Temp units.
JOIN TERMINAL 14-16 GAUGE
07-00397-06
Deutsch connectors. Used on 1st generation
Multitemps (10-pin plug) Deutch HD10
SOCKET TERMINAL 14-16 GAUGE
07-00397-07
Deutsch connectors
JOIN TERMINAL 14-18 GAUGE
07-00397-08
Deutsch connectors
SOCKET TERMINAL 16-18 GAUGE
Deutsch connectors -- Superseded by
22-01613-15
2--9
07-00397-09
Electrical
Description
PIN TERMINAL 12-GAUGE
Part Number
07-00397-10
Deutsch connectors
SOCKET TERMINAL 12-14 GAUGE
07-00397-11
Deutsch connectors
CAVITY PLUG 12-16 GAUGE
07-00397-12
Deutsch connectors
SOFTWARE CARD PROGRAMMER
07-00398-00
This card programmer is used to reprogram the
software cards that are used on the “NT”
Microlink 2 and Microlink 2i controllers.
STEPPER JUMPER ASSEMBLY
NT jumper cable for microprocessor and stepper
motor driver.
2--10
07-00408-00
Electrical
Description
TESTER, ML2I/ML3
Part Number
07-00428-00SV
This is a tester used to determine the integrity of
the ML2i and ML3 microprocessors.
LIGHT BULBS
For use with previously offered Temperature
Controller/Diode Board Test Module
07-00208-00. Package of 5.
16-03004-00
SOCKET TERMINAL
22-01777-03
Female terminal for 22-01777-00SV and
22-01777-01SV microprocessor connectors.
CABLE SPLICE KIT, PORTABLE
22-50199-00
For the quick and easy splicing of 4-conductor
SO portable cable in one convenient package.
Primary use: Container / Genset power cords.
JUMPER, CONFIG (Advance Microprocessor)
Config Mode Jumper --White Wire. Used to put
Advance Micro into Configuration / Diagnostic
/Component Test Modes
2--11
22-50180-00
Electrical
Description
JUMPER, PC MODE
(Advance Microprocessor)
Part Number
22-50180-01
PC Mode Jumper -- Green Wire. Allows Advance
Micro to power up without turning on the SROS
switch.
CABLE, MONITOR PROGRAM
22-01690-00
Used to connect a PC 9-pin serial (COM1) port to
the 3-pin Packard serial port on a Summit Microprocessor unit (Supra, Ultra, Ultima, Extra, Solara,
etc.) Can also be used with the Monitor Program or
the ReeferManager Program (12-00616-00).
DATALINK ADD-ON TRUCK KIT
76-00550-00
Used to add DataLink to truck units.
CARD DRIVE, PC (PARALLEL PORT)
07-00438-00
CARD DRIVE, PC USB PORT
07-00439-00
2--12
Electrical
Description
DIAGNOSTIC TOOL,CAB COMMAND CABLE
Part Number
07-00440-00
Used to diagnose the cab command cable on
30/40/50S and 30/40/50X truck units.
05G UNLOADER CONVERSION, R134A, 24VDC
74-50111-00
R134A, 24VDC, 05G electric unloader conversion
kit used in bus/rail applications. Converts pressure
hot gas bypass unloaders to electric actuated
05G UNLOADER CONVERSION, R-22, 24VDC
74-50111-01
R-22, 24VDC, 05G electric unloader conversion kit
used in bus/rail applications. Converts pressure
hot gas bypass unloaders to electric actuated
05G UNLOADER CONVERSION, R134A, 37VDC
74-50111-02
R134A, 37VDC, 05G electric unloader conversion
kit used in bus/rail applications. Converts pressure
hot gas bypass unloaders to electric actuated
05G UNLOADER CONVERSION, R-22, 37 VOLT
VDC
R-22, 37VDC, 05G electric unloader conversion kit
used in bus/rail applications. Converts pressure
hot gas bypass unloaders to electric actuated
2--13
74-50111-03
Electrical
Description
TEMPERATURE TESTER -- 4-LEAD
Part Number
07-00462-00
This tester allows monitoring and recording of
temperatures on four stations at once. The
15-foot sealed probes allow the user to reach
connection points at multiple appliances. Comes
with two 15-foot leads with probes and two
clamp straps.
Features
D 40 to 300°F (--40 to 150°C)
D MIN/MAX record
D Displays differential temperature (T1 -- T2)
D Displays in °F or °C
D Selectable resolution of 0.1 or 1 degree
D
D
Data hold
Positive-response rubber buttons keep dust
and moisture out
D Low mass thermistor sensors provide fast
response and high accuracy.
TEMPERATURE PROBE -- 15’ SEALED
07-00462-01
15-foot sealed temperature probe for use with
the 07-00462 meter
TEMPERATURE PROBE -- AIR, 15’ SEALED
07-00462-03
15-foot air temperature probe for use with the
07-00462 meter
DISPLAY REMOTE TEMP
Used to allow a reefer mechanic to read setpoint
temperature setting or the active probe
temperature with a digital display on Container
units equipped with Carrier’s controller. Must be
used with harness CTD P/N 22-50058-00 (order
separately).
07-00252-00
REMOTE TEMPERATURE HARNESS
Used as a adapter harness allowing hook-up of
remote temperature meter (CTD P/N 07-00252)
to Carrier’s Solid State Control (analog) on older
container units.
22-50058-00
2--14
Electrical
Description
PRINTER, PORTABLE
Part Number
12-50150-10SV
Print data directly from the on-board data recorder
on the Advance Micro units. (Supersedes
12-00543-10)
12-50150-03
ADAPTER,100-240/VAC CHARGER
AC battery charger cable for use with the
12-50150-10SV printer.
ADAPTER,12V DC CHARGER
12-50150-04
DC battery charger cable for use with the
12-50150-10SV printer.
REPLACEMENT PAPER ROLLS, PACK OF 5
12-50150-01
Paper for the 12-00543-10SV printer
BATTERY PACK, LITHIUM ION
12-50150-02
Use with the 12-00543-10SV printer
PAPER ROLLS, PACK OF 5
Replacement paper for portable
(12-00543-00 and 12-00543-10)
12-00543-01
printers
DOWNLOAD CABLE, 6-FOOT
Used to download data from DataLink data
recorders and also to communicate and download
from Advance microprocessor. Used with
12-00543 printers and other applications.
2--15
22-01737-00
Electrical
Description
DOWNLOAD CABLE, 20-FOOT
Part Number
22-01737-04
Used to download data from DataLink data
recorders and also to communicate and download
from Advance microprocessor. Used with
12-00543 printers and other applications.
BATTERY PACK, RECHARGEABLE
12-00543-02
NI -- Cad rechargeable battery pack used on the
portable printer (12-00543-00 and -10).
ADAPTER, 120 VAC
12-00543-03
Used to power the portable printer (12-00543-00
and -10) from a 120VAC power source.
ADAPTER, 12 VDC VEHICLE
12-00543-04
Used to power the portable printer (12-00543-00)
from a vehicle.
40S/50S and 40X/50X SOFTWARE “UPLOAD”
KIT
76-61011-00
DATALINK RETROFIT KIT
76-00669-10
Used on all trailer units (except Ultima) starting
with serial number: DAY90283472.
2--16
Electrical
Description
DATALINK RETROFIT KIT
Part Number
76-00669-20
Used on all Ultima units starting with serial number:
DAY90283472.
DATALINK RETROFIT KIT
76-00669-21
Used on all XT units.
RED INSULATING VARNISH
07-00479-00
Red glyptol varnish used on alternator studs. This
varnish is usually painted on with a brush. Sold in a
2 ounce bottle.
SHIM, VECTOR GENERATOR SERVICE
Used to protect generator windings during service/
shipping.
2--17
54-00630-25
Electrical
Description
Part Number
Software and PC Cards
CARD, DOWNLOAD -- 7 UNIT CAPACITY -- NAO
12-00503-50
Used to quickly download data from Advance
Microprocessors.
CARD,
CONFIGURATION
MICROPROCESSOR, NAO
--
ADVANCE
12-00506-50
Used to install either a single configuration OR
IntelliSet settings into an Advance Microprocessor.
The Card can be used multiple times with no
limitation on the number. Customer Configuration
Files or IntelliSet Files that are available on the
Carrier Transicold Information Center can be
written to the card using the ReeferManager
Program.
CARD, OPTION -- DATATRAK, NAO
12-00505-53
Five-Click DataTrak Option Card. Used to activate
the DataTrak (remote communications for satellite) Option in the Advance Microprocessor.
CARD, OPTION -- DATATRAK, NAO
12-00505-52
10-Click DataTrak Option Card. Used to activate
the DataTrak (remote communications for satellite) Option in the Advance Microprocessor.
CARD, OPTION -- INTELLI SET, NAO
Five-Click IntelliSet Option Card. Used to activate
the
IntelliSet
Option
in
the
Advance
Microprocessor.
2--18
12-00505-71
Electrical
Description
CARD, OPTION -- INTELLI SET, NAO
Part Number
12-00505-70
10-Click IntelliSet Option Card. Used to activate
the
IntelliSet
Option
in
the
Advance
Microprocessor.
CARD,
PROGRAM
-MICROPROCESSOR -- NAO
ADVANCE
12-00504-50
Used to quickly install new software into Advance
Microprocessor. Can be updated to latest software
version using ReeferManager. (Latest version will
be supplied)
CARD, PROGRAM -- ML3 CONTROLLER
SOFTWARE AND CONFIGURATION
12-00594
Used to quickly install new software into Container
ML3 microprocessors. (Latest version will be
supplied)
CARD, DATABANK DOWNLOAD
12-00615
Used
to
download
Container
ML3
microprocessors. (Latest version will be supplied)
SOFTWARE, DATAVIEW -- 69NT
Includes: 12-00413-05 Rev 7.2 recip software,
12-00528-00 Rev 9.1 scroll software, 62-02575-07
manual.
NOTE: This Microsoft DOS-based product is still
being made available, but is no longer supported
and there have been no updates since this release
in October 1999. Consequently, any events or
alarms added to ML2, ML2i, or ML3 software since
October 1999 will return Unknown event or
Unknown alarm when viewed with Dataview. For
full functionality, purchase the the Microsoft Windows-based version of DataLine (Part number
07-00421-00).
2--19
07-00406-00
Electrical
Description
SOFTWARE, DATALINE
Part Number
07-00421-00
The DataLine for Windows kit includes:
D Software installation CD (1)
D Installation floppy disks (approx 15)
D User’s Guide -- CTD publications P/N T-303
LICENSE, DATALINE
Additional DataLINE licence.
SOFTWARE, MONITOR PROGRAM
07-00426-00
12-00351-06SV
DOS based program for troubleshooting, data
recording + setting up hourmeters in standard Ultra
Family Microprocessors.
SOFTWARE, REEFER MANAGER AND REPORTS
12-00616-00
For use with: Windows 95/98/ME /2000/XP.
Used to set up and download Advance and Summit
microprocessor and DataLink data recorders. For
more information refer to service bulletin
SER04-40.
NOTE: This program replaces the Monitor Program 12-00351-06SV and does everything the
Monitor Program does and more.
DATACOLD 500R
79-60598-20
Used on truck units
DATACOLD 500T
Used on trailer units
2--20
79-60598-00
Electrical
Description
DATALINK FLASHCARD
Part Number
12-00400-00/XX
16-connector slide socket
PROTECTIVE CASE
Used to protect PCMCIA cards.
2--21
58-50109-00
Engine
Description
EXTRACTOR, VALVE GUIDE
Part Number
07-00046-00
Valve guide extractor used on Perkins engine
ADAPTER (PERKINS ENGINE)
07-00054-00
Used to pull liners on Perkins engines.
TESTER, INJECT NOZZLE
07-00140-00
Kit used to check and adjust the fuel Injectors in
diesel engines.
TESTER INJECT NOZZLE REPLACEMENT
BOWL (ACCESSORY FOR 07-00140-00)
07-00140-10
ADAPTER INJECTOR LINE (ACCESSORY FOR
07-00140-00)
07-00036-00
Adapter line for tester inject nozzle. Accessory for
tester inject nozzle. (P/N 07-00140-00)
3--1
Engine
COMPRESSION TESTER KIT (DIESEL
ENGINES 150-850PSI)
Used to check engine compression on various
diesel engines. The kit comes with the compression tester, handle, high pressure tester hose assembly, fitting to go from the injector adapter to
the high pressure tester hose, replacement cards,
and an instruction CD.
NOTE: The following accessories/adapters
(07-50005-02 and 07-00179-02 through -10) are
used with this item.
HOSE, REPLACEMENT HOSE ASSEMBLY (Accessory for 07-00179-01 compression tester)
07-00179-01
ADAPTER, INJECTOR TO TESTER HOSE (Accessory for 07-00179-01 compression tester)
07-00179-09
CHART HOLDER - ORANGE PLASTIC (Accessory for 07-00179-01 compression tester)
07-50005-00
07-00179-08
Holds the compression charts on the compression tester 07-00179-01.
CHARTS, 10-40 BAR (Accessory for
07-00179-01 compression tester)
07-00179-04
CHARTS, 150-850PSI (Accessory for
07-00179-01 compression tester)
07-00179-07
3--2
Engine
COMPRESSION TESTER ADAPTER
Used to check cylinder compression on the new
Tier 4 engines. The injector on the engine is removed and this cylinder put in its place. The compression tester (07-00179-01) is then hooked to
the adapter to run tests.
07-00484-00
ADAPTER, PERKINS 4-108 (Accessory for
07-00179-01 compression tester)
07-00179-02
ADAPTER, MERCEDES 0M636 (Accessory for
07-00179-01 compression tester)
07-00179-03
ADAPTER, KUBOTA 10mm Glow Plug (Accessory for 07-00179-01 compression tester)
07-00179-05
ADAPTER, KUBOTA CT4-114 ENGINE (Accessory for 07-00179-01 compression tester)
07-00179-06
ADAPTER, COMPRESSION TESTER
8mm Glow Plug (Accessory for 07-00179-01
compression tester)
TIMING TOOL
Balance gear timing tool for use on Kohler K301S
gasoline engines.
07-00179-10
3--3
07-00205-00
Engine
SOCKET, INJECTOR
07-00224-00
Socket for injector removal for Kubota IDI engines.
SLEEVE INSTALLER, PERKINS FRONT
CRANKSHAFT PULLEY
07-00227-00
Used to correctly install wear sleeve on Perkins
front crankshaft pulley.
FRONT SEAL INSTALL TOOL, USED ON
4-CYLINDER KUBOTA
07-00239-00
Used to install front seal on Kubota 4-cylinder engines.
PULLER, INJECTOR
07-00249-00
Used on Kubota DI injection engines with pencil
style injectors.
PULLER, INJECTOR (LOW E ONLY)
07-00458-00
Used on the low “e” engine where the injectors have
a larger diameter and different configuration.
CARBON RING INSTALLATION TOOL KUBOTA DI
Used to aid in the installation of the carbon ring
seal in pencil type DI injectors.
3--4
07-00250-00
Engine
SOCKET, WATER TEMPERATURE SENDER
(ADVANCE MICRO UNITS)
Purchase from
Snap-On
Used to remove the Water Temperature Sender on
Advance Units. 3/4” slotted, deep well socket. Must
purchase locally or from Snap-on dealer. Snap-on
part number: S6155.
WRENCH, DAVCO FILTER
07-00423-00
Used to remove and install the Davco fuel filter
METER, COOLANT REFRACTOMETER
07-00435-00
Used for testing integrity of glycol and features an
illuminated refractometer. (USES: EG = ethylene
glycol, PG = propylene glycol)
COOLANT BOTTLE TEST ADAPTER
07-00468-00
Used to pressure test new pressurized coolant
bottles on trailer units. It is to be used with a standard radiator pressure tester.
COOLANT BOTTLE TEST ADAPTER
07-00469-00
Used with a radiator pressure tester (Stant or equivalent) to test the coolant bottle cap. Used on newer
units with pressurized coolant bottle.
MAIN BEARING INSTALL TOOL
Used to install the main bearing on the newer, low
emission engines (starting with serial number
3S00001).
3--5
07-00472-00
Engine
MAIN BEARING EXTRACT TOOL
07-00473-00
Used to extract the main bearing of the new fourcylinder, low emission Kubota engine (starting with
serial number 3S00001).
MAIN BEARING INSTALL TOOL
07-00474-00
Used to install main bearing on the older four-cylinder Kubota engines (prior to serial number
3S00001).
MAIN BEARING EXTRACT TOOL
07-00475-00
Used to extract the main bearing on the older fourcylinder Kubota engines (prior to serial number
3S00001).
CRANK PULLEY IMPACT SOCKET
SIM-583
Used on Kubota crankshaft pulley nut. 1-13/16”
(46mm) deep well impact socket.
NOTE: Must purchase locally from Snap-on or a
Snap-on dealer.
REMOVAL BRACKET, VECTOR GENERATOR
Used on Vector trailer units.
3--6
SKM-5670
Engine
ENGINE PLATFORM TOOL
86-04751-00
Used to remove Vector 6500 generator.
OIL DRAIN TOOL VECTOR 6500
68-15763-00
Used to drain the oil from the engine on Vector 6500
Units. Often used with bracket part number
68-15706-00.
OIL DRAIN TOOL (X2)
68-15763-01
Used to drain the oil from the engine on (X2) trailer
units. Often used with bracket number
68-15706-00.
TACHOMETER, LASER, RPM
07-00488-00
Used to read RPMs on rotating devices.
STROBE LIGHT
Used to set and check engine and compressor
speed. Can be used to freeze motion of pulleys,
fan blades, etc. This strobe is a replacement for
part number 07-00206-00.
07-00486-00
FLYWHEEL LOCKING TOOL
07-60083-00
Used on Vector trailer units to prevent the engine
from turning while working on the generator.
3--7
Engine
LIFTING TOOL, VECTOR GENERATOR
07-60085-00
Used on Vector trailer units as a generator service tool.
SHIM, VECTOR GENERATOR SERVICE
Used to protect generator windings during service/
shipping.
3--8
54-00630-25
Fittings
Description
FITTING, MALE 1/4” NPT X MALE 1/4” FLARE
ACCESS PORT WITH SCHRADER
Part Number
06DA-403-844
7/16-20 MALE STRAIGHT THREAD O-RING X
1/4” MALE ACCESS SCHRADER
0TB0889
Access fitting
FITTING, MALE 1/8” NPT X MALE 1/4” FLARE
ACCESS PORT WITH SCHRADER
17-13010-00
CAP, 1/4” SERVICE VALVE GAUGE PORT
(SHOULD NOT BE USED ON SCHRADER
TYPE PORTS)
40-00086-04
Acorn style gauge port cap. SHOULD NOT BE
USED ON SCHRADER TYPE PORTS.
CAP, 1/4” FLARE (TO BE USED ON
SCHRADER TYPE GAGE PORTS)
DD19CA061
For use on SCHRADER type gage ports
(includes rubber O-Ring/gasket)
CAP, 1/4” FLARE -- PLASTIC
58-60232-00
This is a 1/4” plastic cap used to cap off the
Shrader access fitting after service. It comes with
an o-ring which is not sold separately.
CAP, 3/8” FLARE
40-00086-06
Used on trailer unit king valves.
CORE, SHRADER VALVE
Shrader valve core used in the standard 1/4”
Shrader fittings. Typically used on the older
CFC/HCFC access fittings such as 40-01124-00.
Package of 10.
4--1
14-00351-00
Fittings
Description
SHRADER CORE, 3/8”,134A
Part Number
40-60087-01
Standard Shrader core for 134A access fittings.
Primarily used for Manuli in-line fittings, but can
also be used with other access valves.
ADAPTER, R134A (LO)
40-01184-00
This is a 134A adapter that mounts on a 1/4”
flare, low side.
NOTE: Replacement o-ring is part number
40-01184-50.
ADAPTER, 1/4” NPT X 1/2” ACME
07-00301-00
MALE 1/4” NPT X FEMALE 7/16” STRAIGHT
THREAD O-RING
07-00319-00
PLUG, 7/16”-20 STRAIGHT THREAD O-RING
17-44037-00
PLUG, 9/16”-18 STRAIGHT THREAD O-RING
17-44706-00
90 ELBOW SWIVEL FEMALE 7/16”-20
STRAIGHT THREAD O-RING X M13
40-00519-00
90 ELBOW SWIVEL FEMALE 7/16”-20
STRAIGHT THREAD O-RING X M15
40-00519-01
4--2
Fittings
Description
QUICK CONNECTOR NIPPLE (R134A LOW
SIDE) X M13 (w/ CAP)
Part Number
40-00520-00
QUICK CONNECTOR NIPPLE (R134A LOW
SIDE) X M15 (w/ CAP)
40-00520-01
CAP, LOW SIDE R134A QUICK CONNECT
FITTING
40-00520-02
CAP, HIGH SIDE R134A QUICK CONNECT
FITTING
40-00520-03
90 ELBOW SWIVEL R134A MALE M13
STRAIGHT THREAD X FEMALE M13
40-00523-00
90 ELBOW SWIVEL R134A MALE M15 O-RING
X FEMALE M15
40-00523-01
90 ELBOW MALE 1/4” NPT X FEMALE M13
R134A LOW SIDE
40-00524-00
90 ELBOW MALE 1/8” NPT X FEMALE M15
R134A HIGH SIDE
40-00524-01
4--3
Fittings
Description
MALE 9/16”-18 STRAIGHT THREAD O-RING X
FEMALE 1/4” NPT
Part Number
40-00528-00
MALE 7/16”-20 STRAIGHT THREAD O-RING X
FEMALE 1/4 NPT
40-00528-02
COUPLING, R134A
40-00529-00
7/16” X 20 coupling size by M8 quick connect
TEE, FEMALE 1/4” FLARE SWIVEL X MALE
1/4” FLARE X LS QUICK CONNECT
40-00545-00
SHRADER FITTING BODY, 1/4” MALE FLARE
-- BRAZE IN
This Shrader can be brazed into most refrigerant
lines and used as an access fitting for service. it
is 1/4” flare by 1/4” ID or 3/8” OD sweat.
40-01124-00
90 ELBOW MALE 9/16”-18 STRAIGHT
THREAD O-RING X FEMALE 1/4” NPT
40-01166-00
90 ELBOW MALE 7/16”-18 STRAIGHT
THREAD O-RING X FEMALE 1/4” NPT
40-01166-01
NOTE: O-ring not sold separately.
TEE, SNUBBER 1/8”NPT X 1/8”NPTF
Pressure switch mounting tee (Trailer products)
4--4
79-00965-00
Fittings
Description
ADAPTER, FEMALE 1/4” X QUICK CONNECT
(HIGH SIDE)
Part Number
AC302-438
ADAPTER, FEMALE 1/4” X QUICK CONNECT
(LOW SIDE) W/ CAP
AC302-439
ADAPTER, 90 DEGREE FEMALE 1/4” FLARE
X QUICK CONNECT (HIGH SIDE)
AC302-440
ADAPTER, 90 DEGREE FEMALE 1/4” FLARE
X QUICK CONNECT (LOW SIDE)
AC302-441
RETROFIT KIT, SERVICE PORTS FOR 134a
FITTINGS (AUTOMOTIVE)
AC302-458
4--5
General Unit
Description
GAUGE, MAGNEHELIC
Part Number
07-00177-00
Used to accurately set the defrost air switch,
which initiates defrost cycle. Includes carrying
case, fittings and aspirator.
ASPIRATOR
07-00177-01
Replacement aspirator for Magnehelic gauge
(P/N 07-00177-00).
STROBE LIGHT
Used to set and check engine and compressor
speed. Can be used to freeze motion of pulleys,
fan blades, etc. This strobe is a replacement for
part number 07-00206-00.
07-00486-00
FLASHTUBE, XENON (FOR 07-00206-00
STROBE LIGHT)
Replacement bulb for strobe light (P/N
07-00206).
DIAPHRAGM INSTALLATION TOOL
07-00206-01
07-00231-00
Used to position and install the diaphragm in the
Jackes Evans SV valves.
BELT ALIGNMENT TOOL
For belt alignment on early Thunderbird (NDJ)
units.
JACKSHAFT ALIGNMENT TOOL
For jackshaft alignment on early Thunderbird
(NDJ) units.
5--1
07-00247-00
07-00247-01
General Unit
Description
BELT ALIGNMENT TOOL -- LASER
Part Number
07-00463-00
Laser alignment tool quickly identifies the two most
common types of pulley misalignment -- parallel
offset and angular -- that reduce belt and pulley service life and produce unwanted noise.
GAUGE, BELT TENSION
07-00203-00
Used to adjust belt tension of all non-cogged
V-belts. Proper belt tension increases both
bearing and belt life.
TESTER, BELT TENSION
Used to test belt tension.
07-00253-00
RUBBER BAND
Replacement part for belt tension tester (P/N
07-00253-00).
07-00253-01
HEAT GUN, 220V-50/60
07-00256-01
This heat gun, used to apply heat 500 -- 750_F
(260 -- 400_C) for heat shrink insulation on
electrical connections, speed up curing of
epoxies and general drying. 220 volts AC 50/60
Hz
HEAT GUN, 20V, 570-1000_ F
This heat gun replaces part number
07-00256-00, which is no longer available from
the supplier. It is used to heat shrink-tubing on
wiring connectors and splices. It can also be
used to defrost coils, although caution should be
used as the high temperature setting will actually
melt the aluminum fins.
5--2
07-00487-00
General Unit
Description
THERMOMETER, POCKET
Part Number
07-00261-00
Bi-metal thermometer for measuring temperature
from 25 to 125_F.
THERMOMETER, DIGITAL, POCKET
07-00485-00
This is a straight digital (thermistor type) pocket
thermometer with a 3-foot probe. Reads in _F
only (for _C, refer to the 07-60111-00 instruction
sheet 98-50673-00).Thermometer replaces
discontinued part number 07-00269-00, which
read in _F and _C.
THERMOMETER, DIGITAL, POCKET,
DEGREES CENTIGRADE
07-60111-00
Used to measure temperature (replaces
07-00269-00). For degrees Fahrenheit version,
see 07-00485-00.
THERMOMETER, NON-CONTACT
Used for checking temperatures at a safe
distance. Aim the thermometer and pull the
trigger for a temperature reading of 0 to 750_F
(--18 to 400_C) without the danger of moving
parts or getting burned. Power 9V battery with
low power indicator.
Features: ±2% Accuracy and LCD backlight.
This meter is more advanced than the
07-00323-00 with Max --min -- average
temperature and high or low audio/visual alarm
5--3
07-00324-00
General Unit
Description
THERMOMETER, INFRARED
Part Number
07-00478-00
This infrared non-contact thermometer replaces
07-00323.
D Infrared Thermometer
D Certificate of Calibration:Yes
D Temperature Measuring Range:--32 C to 600 C
D Temperature Accuracy +/--:2 F
D Response Time:500mS
D Accuracy:+/--1%
D Battery Size Code:9V RoHS Compliant: NA
TEMPERATURE PROBE, (--40°F -- 1,500°F)
07-00425-00
This adapter allows the 07-00243-10 Fluke multimeter to be used as a digital thermometer. It can
allow the meter to read in degrees F or C. This
adapter comes with one bead probe and can convert any digital multimeter with a 10mohm input
into a thermometer. Accepts type “K” thermocouple probes and sensors. Accuracy: 0.5%
TEMPERATURE PROBE, (--40_F -- 1,500_F)
07-00424-00
To be used with adapter part number 07-00425-00.
This temperature probe is used in conjunction with
the Fluke multimeter 07-00243-10. It is a universal
probe that can measure air temperatures from
--40_ F to 1500_ F, including high exhaust temperatures. This temp probe uses the type “K” thermocouple which is the most accurate and quickest
responding in the in the industry today.
SENSOR, THERMOMETER
Sensor used with the 12-50039-00 and
12-50040-00 thermometers.
SENSOR, THERMOMETER -- 50 FEET
SENSOR, THERMOMETER -- 10 FEET
SENSOR, THERMOMETER -- 18 FEET
5--4
12-50041-50
12-00569-51
12-00569-52
General Unit
Description
LEADS, 50 FOOT
For use with previously offered Simpson
Temperature Tester, 07-00013-00
Part Number
07-00013-02
MALE ADAPTER (BOTH ENDS), 15 foot
For use with previously offered Simpson
Temperature Tester, 07-00013-00.
07-00013-03
CASE, METER, FOR USE WITH 07-00013-00
For use with previously offered Simpson
Temperature Tester, 07-00013-00
07-00015-00
TACHOMETER, LASER, RPM
07-00488-00
Used to read RPMs on rotating devices.
ROD FOR SERVICING SELF-ADJUSTING
IDLERS ON FRIGIKING TRUCK UNITS
Rod for servicing self-adjusting idlers on Frigiking
truck units.
BARRIER, FLAME
Used to isolate heat when working in tight
quarters.
5--5
07-00276-00
07-00302-00
General Unit
Description
SOCKET, SPANNER FOR ULTRA GEARBOX
Spanner socket for Ultra gearbox clutch.
Part Number
07-00303-01
CLUTCH NUT TOOL
Clutch nut tool for Extra XT.
07-00303-02
AIR GAP GAUGE TOOL (ULTRA CLUTCH)
Used to measure the air gap on the 90 degree gear
box clutch.
07-00360-01
GAUGE TOOL, AIR GAP, CLUTCH
07-00432-00
Used on the following trailer unit models: Ultima,
Extra XT, Ultra XT, Ultra XTC, and Ultima XTC.
Similar in design to part number 07-00360-01.
5--6
General Unit
Description
SEAL PILOT, SMALL ULTRA GEARBOX
Pilot for small seal on Ultra gearbox.
Part Number
07-00308-00
SEAL PILOT, LARGE ULTRA GEARBOX
Pilot for large seal on Ultra gearbox.
07-00309-00
SEAL DRIVER, SMALL, ULTRA GEARBOX
Driver for small seal on the output shaft (clutch
side) of the Ultra gearbox.
07-00310-00
SEAL DRIVER, LARGE, ULTRA GEARBOX
Driver for large seal on the input shaft (drive end)
of the Ultra gearbox.
07-00311-00
SLEEVE TOOL, SEAL
07-00339-00
Used to guide the fan shaft cap end seal during
installation.
5--7
General Unit
Description
DRIVER TOOL, SEAL
Part Number
07-00340-00
Used to drive the fan shaft cap end seal during
installation.
SLEEVE TOOL, SEAL
07-00341-00
Used to guide the fan shaft flange end seal
during installation
DRIVER TOOL, SEAL
07-00342-00
Used to drive the fan shaft flange end seal
during installation.
DRIVER, BEARING PLATE
07-00343-00
Aids in the installation of the fan shaft bearing
cone
DRIVER, BEARING
07-00344-00
Aids in the installation of the fan shaft bearing
cup.
GUIDE TOOL, INSTALLATION
Aids in the installation of the fan shaft excluders.
5--8
07-00357-00
General Unit
Description
GAUGE, SHEAVE (34 DEGREE)
Part Number
07-00364-00
Used to determine wear of sheaves
WRENCH, SPANNER, FAN CLUTCH
07-00396-01
Used to hold the armature during fan clutch
removal. Used on Ultima and Extra XT units
WRENCH, SPANNER, SOLENOID EVAP
07-00476-00
Used to remove the stem on the remote
evaporator liquid solenoid valve. Due to space
restrictions, this tool attaches to a 1/2 inch drive
socket ratchet.
CONDENSER FAN REMOVAL TOOL
07-00399-00
Used to remove P/N 38-00503-00 condenser fan
on 69NT40-511 units.
CROWFOOT WRENCH -- 1 1/8”
07-00409-00
3/8” drive open end crowfoot wrench, used on NT
scroll economizer valve.
CROWFOOT WRENCH -- 1 3/8”
3/8” drive open end crowfoot wrench; used on NT
scroll suction and discharge valves.
5--9
07-00410-00
General Unit
Description
CROWFOOT WRENCH -- 2 1/8”
Part Number
07-00411-00
3/8” drive open end crowfoot wrench; used on NT
Scroll -- Suction Modulation Valve.
BIT, TORX DRIVER
07-00418-00
Container battery unlock tool, used to remove the
TORX screws on the display to access the lithium
back-up battery.
MIRROR, INSPECTION
07-00477-00
Replacement for discontinued part number
07-00437-00. This mirror is the same design except that it now telescopes from 10 to 14 inches in
length instead of 15 inches. It has a diameter of
2.25 inches round.
RIVNUT TOOL, FRAME REWORK
07-00449-00
This tool is for use on unit frame rework kits
(76-00768-00 and -01). It is used in conjunction
with the 07-00448-00 drill bit.
TAP, THREAD LEFT HANDED
This thread tap tool is used to clean out the threads
in the end of the fan shaft (50-00232-##) during
service on XT units.
NOTE: The fan shaft (50-00232-##) also has external threads that hold the clutch on with a spanner nut. These threads can be cleaned/chased using a thread die, 1-9/16--18NS--3, left handed. This
tool is to be be purchased from a local machine
shop or distributor.
5--10
07-00453-00
General Unit
Description
LIFTING DEVICE, 30S UNITS
Part Number
07-60049-00
This is a 3-way hoist used to lift 30S units during
installation.
LIFTING DEVICE, 40S/50S UNITS
07-60091-00
This is a hoist used to lift 40S/50S units during
installation.
LIFTING TOOL, VECTOR GENERATOR
07-60085-00
Used on Vector trailer units as a generator
service tool.
REMOVAL BRACKET, VECTOR GENERATOR
SKM-5670
Used on Vector trailer units.
THREADED ROD, VECTOR GENERATOR
REMOVAL
SKM-5671
Used on Vector trailer units to remove/install the
generator on the engine.
FLYWHEEL LOCKING TOOL
Used on Vector trailer units to prevent the engine
from turning while working on the generator.
5--11
07-60083-00
General Unit
Description
RAIN CAP -- FLIP TOP
Part Number
30-00210-00
This universal flip top rain cap is used to keep
debris and moisture from entering the exhaust
pipe.
SNOWFLAKE
DESIGN
LOCKING
TAB
SIDE HOLES
FOR ADDED
FLOW
ANTI-SIPHON TANK INSERT
These 1.875 inch ID tank inserts are designed to
foil even the most determined thief. Made from the
finest quality materials, they offer the following key
benefits:
D Easy snap-in installation
D Self-locking when snapped in
D 60 gallon-per-minute flow rate
D No hassling with keys and locking fuel caps
D Low cost
EPOXY REPAIR KIT for EVAPORATOR PODS
65-50001-00
QUICK START, COMPRESSOR
07-00494-00
Kit used to test-start small 115VAC hermetic
compressors up to 5HP. This kit was set up for
use with Comfort Pro APU compressors, but will
also work with others if appropriate amperage
fuse is used.
5--12
76-50063-00
General Unit
Description
FUSE, RESETTABLE, 20A
Part Number
07-00494-10
Used in the 07-00494-00 Quick Start kit for
Comfort Pro APU compressors.
NOTE: This fuse was only sized for use on APU
compressors. For all others, check the LRA and
follow instructions.
METER, COOLANT REFRACTOMETER
07-00435-00
Used for testing integrity of glycol and features an
illuminated refractometer. (USES: EG = ethylene
glycol, PG = propylene glycol)
COOLANT BOTTLE TEST ADAPTER
07-00468-00
Used to pressure test new pressurized coolant
bottles on trailer units. It is to be used with a standard radiator pressure tester.
COOLANT BOTTLE TEST ADAPTER
Used with a radiator pressure tester (Stant or equivalent) to test the coolant bottle cap. Used on newer units with pressurized coolant bottle.
5--13
07-00469-00
Refrigeration
Description
MANIFOLD GAUGE SET
Part Number
07-00294-00
Used on R134a systems. Gauges read in PSI.
Hoses are barrier type hoses with quick connect
couplers on the hi and low side hoses and 1/2
acme fitting on the center hose.
MANIFOLD GAUGE SET
07-00294-05
Used on R134A systems. Gauges read in bar.
Hoses are barrier type hoses with quick connect
couplers on the hi and low side hoses and 1/2
Acme fitting on the center hose.
Includes: Hose Set 07-00307-00, Coupler
07-00307-04 and Coupler 07-00307-05
MANIFOLD GAUGE SET, KIT “CFC”
07-00314-00
Used on R-12, R-22, R-500 and R-502 systems.
Hoses are 60” barrier type hoses with anti-blowback valves on the service ends.
Includes: Handwheels 07-00237-04, Gauge
07-00237-05, Gauge 07-00237-06, Hose Set
58-04030-00
HANDWHEEL PACKAGE
07-00237-04
Hand wheel set for most older gauges. Replacement wheels for the 07-00294-05 and older Robinair sets.
LOW SIDE GAUGE, COMPOUND FOR CTD
P/N 07-00294-00
Low side compound gauge for P/N 07-00294-00.
Gauge reads in PSI.
6--1
07-00294-01
Refrigeration
Description
HIGH SIDE GAUGE, PRESSURE FOR CTD P/N
07-00294-00
Part Number
07-00294-02
High side gauge for P/N 07-00294-00. Gauge
reads in PSI.
GAUGE, COMPOUND FOR CTD P/N
07-00314-00 CFC
07-00237-05
Low side compound gauge for P/N 07-00314-00.
GAUGE, COMPOUND FOR CTD P/N
07-00314-00 CFC
07-00237-06
High side compound gauge for P/N 07-00314-00.
HOSE SET
Replacement hose set for manifold gauge set
(P/N 07-00314-00).
58-04030-00
HOSE SET (CONSISTS OF 07-00307-01, -02,
-03)
Replacement hose set for manifold gauge sets
(P/N 07-00294-00 and 07-00294-05). Includes
Hoses, 07-00307-01, 07-00307-02 and
07-00307-03,
07-00307-00
6--2
Refrigeration
Description
HOSE, YELLOW
Part Number
07-00307-01
72” long, barrier type. Replacement hose for use
on center connection of manifold gauge sets (P/N
07-00294-00 and 07-00294-05).
HOSE, RED
07-00307-02
72” long, barrier type. Replacement hose for use
on high side connection of manifold gauge sets
(P/N 07-00294-00 and 07-00294-05).
HOSE, BLUE
07-00307-03
72” long, barrier type. Replacement hose for use
on low side connection of manifold gauge sets
(P/N 07-00294-00 and 07-00294-05).
GASKET
Replacements for manifold gauge hoses 1/4”.
Package of 6.
07-00237-12
GASKET
Replacements for manifold gauge hoses 3/8”.
Package of 6.
07-00237-13
6--3
Refrigeration
Description
COUPLER, QUICK CONNECT, GAUGE HOSE
LOW SIDE R134A
Part Number
07-00307-04
Quick connect couplers for low side hose on
gauge set (P/N 07-00294-00 and 07-00294-05).
Uses Gasket 07-00331-00 and o-ring
42-50017-00
COUPLER, QUICK CONNECT, GAUGE HOSE
HIGH SIDE R134A
07-00307-05
Quick connect couplers for high side hose on
gauge set (P/N 07-00294-00 and 07-00294-05).
Uses Gasket 07-00331-00 and O-ring
42-50018-00
LOW SIDE QUICK-CONNECT ENDS
07-00294-10
Used with 07-00294-00 gauged set.
HIGH SIDE QUICK-CONNECT ENDS
07-00294-11
Used with 07-00294-00 gauged set.
GASKET
07-00331-00
These are replacement O-rings for the hose side
of couplers 07-00307-04 or 07-00307-05.
Package of 6.
O-RINGS (LOW SIDE, smaller than high side)
These are replacement O-rings for the connection side of quick connect coupler 07-00307-04.
Package of 10.
6--4
42-50017-00
Refrigeration
Description
O-RINGS, (HIGH SIDE, bigger than low side)
Part Number
42-50018-00
These are replacement O-rings for the
connection side of quick connect coupler
07-00307-05. Package of 10.
VACUUM PUMP, DUAL VOLTAGE/DUAL
FREQUENCY 110-115/220-240 VAC 50/60 HZ
6 CFM (free air)
2 stage rotary vane type
1/2 horsepower
Intake fitting 1/4 MFL and 1/2 Acme
Plug not provided
Pre-wired for 220/240 VAC (Change wire terminations in accordance with motor nameplate
for 110-115 volt applications)
REAMER ROD
Reamer Rod used to repair refrigeration coils.
HEAVY DUTY PLUS II CHARGING/VACUUM
HOSE
07-00176-11
07-00220-00
07-00237-10
Pull a vacuum much faster with this 5/16” I.D.
heavy duty hose than with the 1/4” hose. This is
permeation resistant (Plus II) barrier, working
pressure 750psi; 3000psi burst.
REFRIGERATION WRENCH
07-00238-00
Refrigeration wrench for service valve stems
3/16, 1/4, 5/16, 3/8.
REFRIGERATION WRENCH, OFFSET
07-00238-01
Refrigeration wrench, offset for service valve
stems 3/16, 1/4, 5/16, 3/8.
HEAD ASSEMBLY, HALIDE LEAK DETECTOR
07-00259-00
6--5
Refrigeration
Description
ACID TEST KIT, MINERAL and SYNTHETIC
OIL
Part Number
07-00260-00
Acid test kit for mineral and alkyl benzene
compressor oils.
ACID TEST KIT, POLYOLESTER “POE” OIL
07-00337-00
Acid test kit for POE compressor oils.
TOTALTEST KIT, 1 KIT W/ BLUE TUBES
07-00265-01
TotalTest “Blue” is for testing CFC (R-12, 22, 500,
502) refrigerants for moisture and acid contamination.
PACKAGE OF 5 BLUE TUBES
Replacement tubes for the TotalTest kit (P/N
07-00265-01).
07-00266-00
LEAK DETECTOR
07-00295-00
Leak detector for R-12, R-22, R-500, R-502,
R134A, R404A refrigerants.
6--6
Refrigeration
Description
ELEMENT
Replacement kit for leak detector 07-00295-00
Part Number
07-00296-00
PROGRAMMABLE CHARGING/RECOVERY
METER
07-00315-00
Three display modes -- Lbs/oz; Decimal Lbs.; Kilograms
Allows automatic Charging or Recovery operations
Color-coded keypad controls
Very High Resolution -- 0.2 oz./0.010 Lbs./4
grams
Can be used with all refrigerants
Advanced Charge and Recovery Modes -- uses
tare weight and Max. capacity of cylinder to calculate maximum Charge/Recovery available
User Programmable memory for up to 99 different stored values
“Repeat” charge features removable platform and
control box with prop stand/hanging hook
Compact Design -- completely portable, battery
powered with Low battery indicator.
TEMPERATURE TESTER -- 4-LEAD
This tester allows monitoring and recording of
temperatures on four stations at once. The
15-foot sealed probes allow the user to reach
connection points at multiple appliances. Comes
with two 15-foot leads with probes and two clamp
straps.
Features
D 40 to 300°F (--40 to 150°C)
D MIN/MAX record
D Displays differential temperature (T1 -- T2)
D Displays in °F or °C
D Selectable resolution of 0.1 or 1 degree
D Data hold
D Positive-response rubber buttons keep dust
and moisture out
D Low mass thermistor sensors provide fast
response and high accuracy.
6--7
07-00462-00
Refrigeration
Description
TEMPERATURE PROBE -- 15’ SEALED
Part Number
07-00462-01
15-foot sealed temperature probe for use with the
07-00462 meter
TEMPERATURE PROBE -- AIR, 15’ SEALED
07-00462-03
15-foot air temperature probe for use with the
07-00462 meter
METER, REFRACTOMETER FOR
COMPRESSOR OIL
07-00316-00
Used to measure the amount of residual mineral
oil in a system being changed to POE oil.
SUCTION FILTER KIT
07-00379-00
Designed for use with the 05G compressor and
contains all parts needed to cycle the suction gas
though a replaceable element suction line filter.
The kit includes two elements -- a pleated filter
used for solid particulate removal only and a solid
core acid removal element designed for
particulate, water, and acid removal
FILTER, SOLID CORE -- ACID
14-50054-00
Replacement filter used in the 14-50056-00
suction filter shell supplied with the Suction Filter
Kit part number 07-00379-00. It is the activated
core for acid removal within the system.
6--8
Refrigeration
Description
FILTER, REGULAR CORE
Part Number
14-50055-00
Replacement filter used in the 14-50056-00
suction filter shell supplied with the Suction Filter
Kit part number 07-00379-00. It is the regular
core for non-acidic filtering.
SUCTION FILTER SHELL
14-50056-00
This is the filter shell that comes in the
07-00379-00 Suction Filter Kit.
FILTER HOUSING -- INTERNAL
This is the internal filter housing used inside the
filter shell to hold the filter cores in the
14-50056-00.
6--9
14-50056-01
Refrigeration
Description
KIT, HOSE CRIMPING,HYDRAULIC
Part Number
07-00378-00
This tool uses hydraulic operation to crimp the
hose fittings.
NOTE: Does not come with the needed air pump
(AC101-727) or hydraulic hose (AC101-729).
PUMP, AIR POWERED
AC101-727
Air powered foot operated pump for use with the
hydraulic bubble crimper 07-00378-00.
REPAIR KIT,AIR/HYDRAULIC PUMP
07-00392-00
Repair kit for the air/hydraulic crimping pump
AC101-727
RETRO CYLINDER
AC101-728
Replacement part for the hydraulic bubble crimper 07-00378-00
HOSE, 3/8” QUICK CONNECT
Hose 3/8 quick connect for pump P/N
AC101-727.
6--10
AC101-729
Refrigeration
Description
OIL FILTER KIT, 05G COMP
The Compressor Oil Filter kit, designed for use
with 05G, 05K and 06D compressors with gear oil
pumps, comes with an extremely fine micron filter
and a bracket to mount the filter below the
compressor. The filter is used as a bypass from
the compressor oil pump and will not affect
compressor lubrication, even if it becomes
plugged. The compressor will circulate oil through
the filter at a rate of approximately one (1)
gal/minute, making oil clean up time very fast and
efficient. Experience has shown that even very
contaminated systems will clean up within one to
two hours of unit operation with the kit(s)
installed.
KIT, HOSE CUTTER/ CRIMPER (EXPANDER,
CLIP PLIERS, CUTTER, PLASTIC CASE)
Part Number
07-00380-00
07-60009-00
Used to cut, expand, and install Manuli fittings on
Manuli refrigerant hoses.
PLIERS, FITTING ASSEMBLY
(Part of kit # 07-60009-00)
07-00382-00
Used to connect the clamps on the quick click
hose fittings. This is usually used in conjunction
with the 07-00383-00 and the 07-00384-00
ENLARGER TOOL
(Part of kit # 07-60009-00)
Used to enlarge the plastic liner on Manuli hoses
to insert the fittings prior to fastening with the
quick click. Part of 07-60009-00 Kit
HOSE CUTTER
(Part of kit # 07-60009-00)
Used to cut refrigeration hoses. Primarily used
with the Manuli hoses.
6--11
07-00384-00
07-00383-00
Refrigeration
Description
BLADE, HOSE CUTTER (MANULI)
Part Number
07-00383-20
Replacement blade for hose cutter 07-00383-00
TOOL, INSERTION, QUICK CLICK FITTING
07-00417-00
Used to assist the technician in inserting Manuli
fittings into Manuli refrigerant hose before
crimping.
KIT, HOSE CUTTER/ CRIMPER (EXPANDER,
CLIP PLIERS, CUTTER, PLASTIC CASE)
07-60117-00
Used to cut, expand, and install Codan fittings on
Codan refrigerant hoses.
PLIERS, FITTING ASSEMBLY, EZ CLIP
(Part of kit number 07-60117-00)
07-60117-10
Used to connect the clamps on the Codan hose
fittings.
PLIERS, FITTING ASSEMBLY, EZ CLIP
07-00467-00
Used to connect the fitting to hose on Aeroquip
fittings.
HOSE CUTTER TOOL
AC101-708
Hose cutter tool for cutting refrigerant hose to
length.
HOSE CUTTER TOOL BLADE
Replacement blade for hose cutter (P/N
AC101-708).
6--12
AC101-711
Refrigeration
Description
TOOL, PINCH OFF (CU TUBE)
Part Number
07-00385-00
Pinch off tool for process tubes. Primarily setup
for the Matson hermetic container unit
VALVE, PIERCING
07-00386-00
Used to gain access to the refrigerant circuit for
gauge reading, charging, evacuation, recovery,
etc.
DISPENSING GUN, STATIC MIXING
(USED IN KIT 76-50084-00SV)
07-00391-00
Application gun needed to apply Durabond epoxy
used for repair of inserts on container composite
control boxes.
VACUUM GAUGE, DIGITAL (MICRONS)
07-00414-00
Used to measure deep vacuums in microns,
down to 10 microns, for accurate dehydration
vacuums.
Features:
2.5 X 3” size
Fitted with 6-foot lead
SENSOR, REPLACEMENT
Used on the 07-00414-00 digital vacuum gauge
6--13
07-00414-01
Refrigeration
Description
REFRIG. SYSTEM QUICK CHECK KIT
Part Number
07-50006-00
Used with procedures outlined in instruction
sheet 98-50554-00 (R-22/R404A Quick Check
Refrigeration System Troubleshooting Procedure)
It is designed to test the major components used
in the Carrier Transicold trailer refrigeration units
(Phoenix Advantage, Phoenix Ultra, and Optima)
that use refrigerants R-22 or R404A. Kit contains
the 22-50190-00 wire harness and instruction
sheet 98-50554-00.
OIL FILTER KIT, BUS
07-00429-00
Bus 05G compressor oil filter kit for use with vane
style pump. The filter is part number
14-00289-00.
HX/HD, SECURITY, STEPPER VALVE
07-00434-00
This is a specially designed hex bit (Allen
wrench) which fits the adjustment screw on the
stepper valve (14-00263-00) piston.
CHECK VALVE TOOL -- DISCHARGE
07-00457-00
Designed to open the seat on the X series trailer
unit discharge check valve during inert brazing
and unit evacuation.
WRENCH, SPANNER -- UNLOADER STEM
Designed to fit securely onto the 17-40417-00
unloader valve. Tool was developed as a stronger
alternative to the powdered metal tool supplied
with the 17-40418 unloader kit.
6--14
07-00459-00
Refrigeration
Description
RECOVERY UNIT, REFRIGERANT -- 115VAC
Part Number
MVS II - 115
This is the 115VAC Microvac II refrigerant
recovery unit. it is used to remove refrigerant
from units during service.
RECOVERY UNIT, REFRIGERANT -230/240VAC
MVS II - 240
This is the 230/240VAC version of the Microvac II
refrigerant recovery unit.
HOSE CRIMPING TOOL, CFC STYLE HOSE
FITTINGS (R-12 TYPE)
160-0010
THE FOLLOWING PARTS ARE REPLACEMENT PARTS FOR
THE PREVIOUSLY OFFERED 07-00306 HOSE CRIMPING
BUBBLE KIT AND THE CURRENTLY OFFERED HOSE
CRIMPING KIT 07-00445-00.
HOSE CRIMPING KIT, 3710
Hose crimping tool for #6, #8, #10, and #12 hose
6--15
07-00445-00
Refrigeration
Description
DIE GUIDE BLOCK
Part Number
07-00361-00
Replacement part for 07-00306-00 and
07-00445-00
DIE BLOCK HOLDER (REMOVEABLE)
07-00362-00
Replacement part for 07-00306-00 and
07-00445-00
DIE BLOCK HOLDER (MOVEABLE)
07-00363-00
Replacement part for 07-00306-00 and
07-00445-00
DIE SET FOR #8 HOSE (INCLUDES DIE AND
HOLDER)
AC101-723
Replacement part for 07-00306-00 and
07-00445-00
DIE SET for #10 HOSE (INCLUDES DIE AND
HOLDER)
AC101-724
Replacement part for 07-00306-00 and
07-00445-00
DIE SET FOR #12 HOSE (INCLUDES DIE AND
HOLDER)
AC101-725
Replacement part for 07-00306-00 and
07-00445-00
LATCH PLATE
Replacement part for 07-00306-00 and
07-00445-00
6--16
AC101-730
Refrigeration
Description
STRAIN ROD
Replacement part for 07-00306-00 and
07-00445-00
DIE SET FOR #6 HOSE (INCLUDES DIE AND
HOLDER)
Part Number
AC101-731
AC101-732
Replacement part for 07-00306-00 and
07-00445-00
SPRING
AC101-734
Replacement part for 07-00306-00 and
07-00445-00
LOCK SCREW
AC101-735
Replacement part for 07-00306-00 and
07-00445-00
THRUST BUSHING
AC101-736
Replacement part for 07-00306-00 and
07-00445-00
ACTUATOR SCREW
AC101-738
Replacement part for 07-00306-00 and
07-00445-00
DIE HOLDER #8 BLUE
Replacement part for 07-00306-00 and
07-00445-00
6--17
AC101-739
Refrigeration
Description
DIE HOLDER #10 GREEN
Part Number
AC101-740
Replacement part for 07-00306-00 and
07-00445-00
DIE HOLDER #12 CLEAR
AC101-741
Replacement part for 07-00306-00 and
07-00445-00
SHRADER CORE, 3/8”, 134A
40-60087-01
Standard Shrader core for 134A access fittings.
Primarily used for Manuli in-line fittings, but can
also be used with other access valves.
ADAPTER, R134A (LO)
40-01184-00
This is a 134A adapter that mounts on a 1/4”
flare, low side.
NOTE: Replacement o-ring is CTD P/N
40-01184-50.
LEAK DETECTOR
Bubble leak detector used to locate refrigerant
leaks.
6--18
07-50017-00
Shop Supply, Cleaners & Chemicals
Description
GREASE, HEAT CONDUCTIVE SEALER
Part Number
02-00010-00
Used to improve conduction of heat at TXV bulb
locations and as a filler/conductor in sensing
wells.
GREASE, LITHIUM BASE
07-00245-00
Grease, lithium base for use on linear solenoids.
This grease is not affected by moisture, heat, or
cold.
GREASE, SRI-2
46-50001-00
For use on Carrier clutches
GREASE, N-2
46-50002-00
For use on TK bus clutches
OIL, COMPRESSOR (S-100)
Synthetic 100 for R-12, R-22, R-500 and R-502
Typical Use Truck Units.
Package Size: 12 one-quart bottles
7--1
07-00270-00
Shop Supply, Cleaners & Chemicals
Description
OIL, COMPRESSOR -- SYNTHETIC (150)
Part Number
07-00274-00
Synthetic 150 for R-12, R-22, R-500 and R-502
Typical Use Trailer Units.
Package Size: 6 one-gallon containers
OIL, COMPRESSOR -- MINERAL (150)
07-00275-00
Mineral Oil 150 for R-12, R-22, and R-500
Typical Use Trailer Units.
Package Size: 6 one-gallon containers
OIL, COMPRESSOR (R134A)
07-00292-00
POE 22 for R134A
Typical Use Container
Package Size: 12 34-ounce cans
OIL, COMPRESSOR (SW20)
POE 22 for R134A
Typical Use Container
Package Size: 6 one-gallon cans
7--2
07-00292-01
Shop Supply, Cleaners & Chemicals
Description
CLEANER, COIL -- CASE
Part Number
07-00313-00
Citrus type coil cleaner will help clean coils, but
not corrode the coil and is easy on units paint.
Package Size: Package of 6.
OIL, COMPRESSOR (POE 68)
07-00317-00
POE 68 for R134A and R404A
Typical Use 05G and 05K
OIL, COMPRESSOR -- MOBILE POE 22CC
(Rotary Compressor)
07-00318-00
POE 22 for R134A and R404A
Typical Use Truck Unit
12oz
Package Size: 12-ounce can
OIL, COMPRESSOR (S-68)
Synthetic 68 for R-12, R-22, and R-500
Typical Use Truck Units.
Package Size: Package of 6
7--3
07-00320-00
Shop Supply, Cleaners & Chemicals
Description
OIL,COMPRESSOR, PAG (GM 2003
W/DENSO)
Part Number
46-50003-00
PAG oil for GM model year 2003 vans with
DENSO compressors with R134A
OIL,COMPRESSOR, PAG (FOR A-6
COMPRESSOR)
46-50004-00
PAG oil for model A-6 compressors for small bus
A/C applications using R134A
GAS, CALIBRATION
07-00322-00
Used as a standard to calibrate the sensors on
controlled atmosphere units.
ADAPTER FITTING FOR CALIBRATION GAS
Used with 07-00322-00 calibration gas.
7--4
07-00322-02
Shop Supply, Cleaners & Chemicals
Description
OIL, COMPRESSOR (5GS)
Part Number
07-00325-00P12
Mineral Oil 500 for R502. Typical Use Truck
Units Rotary Compressors
OIL, VACUUM PUMP
07-00328-00
Package Size: 12 one-quart bottles
OIL, COMPRESSOR -- PAG FOR DODGE 22
OZ.
07-00332-00
PAG for R134A
Small Bus (Dodge)
Package Size: 22-ounce bottle
OIL, COMPRESSOR -- PAG FOR GM 22 OZ.
PAG for R134A
Small Bus (GM)
Package Size: 22-ounce bottle
7--5
07-00333-00
Shop Supply, Cleaners & Chemicals
Description
OIL, COMPRESSOR -- PAG FOR FORD 22 OZ.
Part Number
07-00334-00
PAG for R134A
Small Bus (Ford)
Package Size: 22-ounce bottle
OIL, COMPRESSOR -- PAG FOR SANDEN
8.45 OZ.
07-00335-00
PAG for R134A
Small Bus (Sanden)
Package Size: 8-ounce can
OIL, COMPRESSOR -- 50PAG, R134A, 1QT
CAN
46-50006-00
Used in R134A refrigerant bus AC circuits with
Seltec/Valeo/Zexel/Ice/Tama TM series
compressors. Sold in a one quart, screw top
metal can.
Package Size: One-quart can
SEALANT, PIPE FITTINGS ON 134A UNITS
07-00345-00
Sealant for pipe fittings on units using HFC
refrigerants (R134A and R404A).
OIL, COMPRESSOR -- POE 35 TK TRAILER
UNITS W/ 404A
POE 35 for R134A and R404A
Thermo King Trailer Units
7--6
07-00349-00
Shop Supply, Cleaners & Chemicals
Description
OIL, COMPRESSOR -- POE 32 TK
CONTAINER UNITS. CASE OF 4 GALLONS
Part Number
07-0035400P04
POE 32 for R134A and R404A
Thermo King Container Units
OIL, SYNTHETIC GEAR BOX 75W-90
(Ultra gear case)
07-00359-00
Synthetic gear oil 75W-- 90 for the 90 degree
trailer unit gear box.
OIL, FANSHAFT -- CASE OF 12, 8 OZ
07-00373-00
Used in the lubrication of fan shafts.
Package Size: Package of 12.
OIL, COMPRESSOR 300 MINERAL
Mineral Oil 300 for R-12, R-22, and R-500
Typical Use Large Bus
7--7
07-00377-00
Shop Supply, Cleaners & Chemicals
Description
OIL, CASTROL E--68
Part Number
07-00405-00
POE Oil Typical use: 5F, 5H, 05K, 06D and 06E
compressors for Marine units.
PAINT, TOUCH-UP, SEAHORSE BLUE
07-00480-00
This spray paint is used to touch up Seahorse units
and other CTD marine blue units.
PAINT, TOUCH-UP (05G and KUBOTA)
07-00420-00
This spray paint is used to touch up scratches on
05G compressors and Kubota engines.
PAINT, TOUCH-UP, HORIZON GREEN
This spray paint is used to touch up scratches on
19D and 19C units.
7--8
PH23GH017
Shop Supply, Cleaners & Chemicals
Description
PAINT, BLUE, COMPRESSOR
Part Number
76-00397-01
This is hull blue compressor paint for use on
CTD container units. There are two cans of
primer and two cans of the epoxy paint.
RED INSULATING VARNISH
07-00479-00
Red glyptol varnish used on alternator studs and is
normally painted on with a brush.
Package Size: 2-ounce bottle
OIL, 32ST
07-00427-00
Mobile Arctic 32 ST polyolester (POE) oil for
R-134. Commonly used for container units with
scroll compressors (69NT40-531 for example)
Package Size: One quart can
OIL, REFRIGERANT (SOLTEX VG 68) GAL
For R-22 bus applications
Package Size: One gallon container
7--9
07-00430-00
Shop Supply, Cleaners & Chemicals
Description
HUMISEAL, 12OZ
Used to seal back of printed circuit boards from
moisture.
Part Number
07-50001-00
SMOKE BOMB
Used to test seal integrity of refrigeration unit to
trailer, trailer tightness, and door seals.
16-00037-00
OIL, COMPRESSOR -- TOTALCLAIM/SAVE
R-12, 22, 500, 502
P903-0901
OIL, COMPRESSOR -- TOTALCLAIM/SAVE
R-134a, R-404A.
P903-1301
PAINT, SEA SPRAY GREEN
Unit Touch-Up paint for miscellaneous 38 series
units. Also used on: 38GR, CC, CB 48, 50, 58
units.
Package Size: 16-ounce can
7--10
PH23GL012
Shop Supply, Cleaners & Chemicals
Description
PAINT, HORIZON GREEN
Unit Touch-Up paint for 19 series units.
Part Number
PH23GH012
Package Size: 16-ounce can
COIL CLEANER
Cal-Brite – Low pH or acid-based product
developed for cleaning evaporator and
condenser coils, safe yet aggressive!
NU4133-08
Package Size: 4 one-gallon jugs
COIL CLEANER
NU4148-08
Cal-Shield with Teflon – Contains Teflon to
shield and protect finned cooling and heating
coils from dirt and corrosion
Package Size: 4 one-gallon jugs
COIL CLEANER
NU4148-32
Cal-Shield W/Teflon – Contains Teflon to
shield and protect finned cooling and heating
coils from dirt and corrosion
Package Size: 6 one-quart bottles
COIL CLEANER
Tri-Pow’r – Alkaline detergent/degreaser for
cleaning air cooled condensers, evap coils,
permanent filters, fan blades, motors, etc.
NU4371-88
Package Size: 4 one-gallon jugs
COIL CLEANER
NU4171-75
Evap Foam No Rinse – High performance,
heavy-duty detergent. Foaming, no rinse,
aerosol evaporator coil cleaner, foams out dirt!
Package Size: 6 – 18-ounce cans
7--11
Shop Supply, Cleaners & Chemicals
Description
COIL CLEANER
Nu-Brite – Revolutionary strong, foaming
condenser coil cleaner, Alkaline. The Acid
alternative!
Package Size: 4 one-gallon jugs
COIL CLEANER
Nu-Brite – Revolutionary strong, foaming
condenser coil cleaner, Alkaline. The Acid
alternative!
Package Size: 2.5 gallon pail or 55 gallon drum
COIL SANITIZER
Bio-Fresh CD – A concentrated, ready to use
bacteriostat-fungistat-deodorizer formulated for
use in HVACR systems. One quart -- Sanitizes
evaporator coils and drain pans, deodorizes and
kills bacteria
Package Size: 12 one-quart bottles
COIL SANITIZER
Bio-Fresh CD – A concentrated, ready to use
bacteriostat-fungistat-deodorizer formulated for
use in HVACR systems. One gallon -- Sanitizes
evaporator coils and drain pans, deodorizes and
kills bacteria
Package Size: 4 one-gallon jugs
COIL SANITIZER
PanPads -- ACP – Condensate drain pads
prevent bacteria and slime in pans. Combats a
broad spectrum of harmful bacteria.
Part Number
NU4291-08
2.5 Gallon
NU4291-05
55 Gallon
NU4291-01
NU4126-34
NU4126-38
NU4295-34
Package Size:
SPRAYER
NU4770-00
Sprayer, No. 50P Poly – Pump sprayer for
coil cleaners, half-gallon capacity.
Package Size: One sprayer
7--12
Shop Supply, Cleaners & Chemicals
Description
SPRAYER
Part Number
NU4771-30
Sprayer, No. 220CP – Pump sprayer for coil
cleaners, 2 gallon capacity.
Package Size: One sprayer
SPRAYER
NU4772-00
Sprayer, No. 300P – Pump sprayer for coil
cleaners, 3 gallon capacity.
Package Size: One sprayer
SPRAYER
NU4774-00
Coil Gun – Hose end sprayer with mixing valve
to dilute coil cleaners
Package Size: One gun
INSULATION
NU4216-92
Insulation Slugs – Thumbing grade slugs for
plugging holes
Package Size: 24 two pound boxes
INSULATION
NU4217-W3
Cork Insulation Tape – Insulation tape for
wrapping refrigerant lines
Package Size: 12 – 2” x 30’ Rolls
INSULATION
NU4218-W3
Foam Insulation Tape – Insulation tape for
wrapping refrigerant lines
Package Size: 12 – 2” x 30’ Rolls
7--13
Shop Supply, Cleaners & Chemicals
Description
INSULATION
Nu-Foam Insulation Foam – A triple
expanding foam that insulates as well as seals
cracks, crevices and other openings. Created for
refrigeration, air conditioning and heating pipes
and tubing.
Part Number
9 oz
NU4293-04
20 oz
NU4293-75
Package Size: 9 oz or 20 oz cans
GAS LEAK DETECTORS
Cal-Blue – Gas leak detector
NU4182-08
Package Size: 4 one-gallon jugs
GAS LEAK DETECTORS
Cal-Blue – Gas leak detector with trigger spray
NU4182-24
Package Size: 12 one-quart bottles
GAS LEAK DETECTORS
Cal-Blue – Gas leak detector with dauber in
cap
NU4182-53
Package Size: 24 – 6-ounce bottles
FLUSH
NU4300-10
Rx11 Flush “2 IN 1” Display – Rx11
flushing solvent for burnouts and oil removal.
Two cylinder pack w/ valve
Package Size: 1 – two-cylinder pack
FLUSH
NU4300-11
Rx11 Flush – Rx11 flushing solvent for
burnouts and oil removal. Single cylinder.
Package Size: Four single cylinders
7--14
Shop Supply, Cleaners & Chemicals
Description
FLUSH
Rx11 Flush – Rx11 flushing solvent for
burnouts and oil removal. 50 ton capacity.
Part Number
NU4300-15
Package Size: 15 pound cylinder
FLUSH
NU4300-99
Rx11 Flush Fitting Assembly – Access
valve for single Rx11 cylinders
Package Size: One valve
FLUSH
NU4301-02
Rx Acid Scavenger – Acid neutralizer for
refrigeration oil. 2oz treats up to one gallon of
contaminated oil.
Package Size: 6 -- two-ounce bottles
HAND TOWELS
Kleen-N-Toss – Scrubbing hand cleaning
towels with special cleanser
NU4230-72
Package Size: 6 – 72 towel buckets
OIL TEST KIT
Phase III– Refrigeration oil acid test kit
Package Size: 24 kits
7--15
NU4320-W8
Alphabetical Index
A
ACID TEST KIT, 6--5, 6--6
ADAPTER, 2--16, 22, 24, 5--5
ADAPTER, INJECTOR TO TESTER HOSE, 3--23
ADAPTER, R--134A (LO), 4--2, 6--18
ADAPTER,100--240/VAC CHARGER, 2--15
ADAPTER,12V DC CHARGER, 2--15
AIR COMPRESSOR TOOL KIT, 1--6
AIR GAP GAUGE TOOL (ULTRA CLUTCH, 5--6
ASPIRATOR, 5--1
B
CLEANER -- COIL, 7--11, 7--12
CLUTCH NUT TOOL, 5--6
CLUTCH TOOL, 1--1
CLUTCH TOOL, AIR GAP, 5--6
CLUTCH TOOL, BEARING PRESS, 1--2
CLUTCH TOOL, STANDBY, 1--2
COIL CLEANER, 7--3
COMPRESSION TEST ADAPTER, 3--24
COMPRESSION TESTER KIT, 3--23
COMPRESSOR OIL, PAG, 7--5, 7--6
COMPRESSOR OIL, POE, 7--6
COMPRESSOR OIL, TOTALCLAIM/SAVE, 7--10
CONDENSER FAN REMOVAL TOOL, 5--9
BARRIER, FLAME, 5--5
COOLANT BOTTLE TEST ADAPTER, 3--26, 5--13
BATTERY PACK, 2--16
CORE, SHRADER VALVE, 4--1
BATTERY PACK, LITHIUM ION, 2--15
COUPLER, QUICK CONNECT, 6--4
BEARING DRIVER, 1--1
CRANK PULLEY IMPACT SOCKET, 3--27
BELT ALIGNMENT TOOL, 5--1, 5--2
CRIMPER, 2--7
BIT, TORX DRIVER, 5--10
CRIMPER, MOLEX, (AWG--8), 2--6
BLADE, HOSE CUTTER (MANULI), 6--12
CRIMPER, PIN, 2--7
BOLT, CLUTCH, 1--1
CRIMPER, WEATHERPACK, 2--7
CRIMPER,MOLEX MINI--FIT , 2--7
C
CRIMPER,MOLEX MINI--FIT (10/12), 2--7
CROWFOOT WRENCH, 5--9, 5--10
CABLE SPLICE KIT, PORTABLE, 2--11
D
CABLE, MONITOR PROGRAM , 2--12
CALIBRATION GAS, 7--4
CARBON RING INSTALLATION TOOL, 3--25
DATACOLD 500R, 2--20
CARD DRIVE, 2--12
DATACOLD 500T , 2--20
CARD, CONFIGURATION, 2--18
DATALINK ADD--ON TRUCK KIT, 2--12
CARD, DOWNLOAD, 2--18, 2--19
DATALINK FLASHCARD, 2--21
CARD, OPTION, 2--18, 2--19
DATALINK RETROFIT KIT, 2--16, 2--17
CARD, PROGRAM, 2--19
DATAREADER KIT, 2--4
CASE, MEGOHMETER, 2--1
DIAGNOSTIC TOOL,CAB COMMAND CABLE, 2--12
CASE, METER, 5--5
DIAPHRAGM INSTALLATION TOOL, 5--1
CAVITY PLUG, 2--10
DIPSTICK, OIL (SANDEN COMPRESSOR), 1--2
CHARGING/RECOVERY METER, 6--7
DISPLAY REMOTE TEMP, 2--14
CHARGING/VACUUM HOSE, 6--5
DOWNLOAD CABLE, 2--15, 2--16
CHART HOLDER, 3--23
DRIVER TOOL, SEAL, 5--8
CHARTS, 3--23
DRIVER, BEARING, 5--8
CHECK VALVE TOOL, 6--14
DRIVER, BEARING PLATE, 5--8
Index --1
Alphabetical Index
E
H
ELBOW, 4--2
HAND TOWELS, 7--15
ENGINE PLATFORM TOOL, 3--28
HANDWHEEL PACKAGE, 6--1
ENLARGER TOOL, 6--11
HEAD ASSEMBLY, 6--5
EPOXY REPAIR KIT, 5--12
EXTRACTOR, 2--6
EXTRACTOR (EPROM), 2--5
EXTRACTOR PIN, 2--5
HEAT GUN, 5--2
HIGH SIDE GAUGE, PRESSURE, 6--2
HOSE, 6--3
HOSE CRIMPING, 6--10, 6--11, 6--15
HOSE CUTTER, 6--11, 6--12
EXTRACTOR, EPROM, I--30S, 2--6
HOSE SET, 6--2, 6--11
EXTRACTOR, MINI FIT SR., 2--6
HOSE, 3/8” QUICK CONNECT, 6--10
EXTRACTOR, PIN, 2--6
HOSE, REPLACEMENT, 3--23
EXTRACTOR, TERMINAL, MOLEX, 2--6
HUMISEAL, 12OZ, 7--10
EXTRACTOR, VALVE GUIDE, 3--22
I
F
FILTER HOUSING -- INTERNAL, 6--9
INSERTER (EPROM), 2--5
INSTALL TOOL, T.K. SHAFT SEAL, 1--3
INSULATION , 7--13, 7--14
FILTER, FELT SOCK, 1--4, 1--5
FILTER, REGULAR CORE, 6--9
J
FILTER, SOLID CORE -- ACID, 6--8
FITTING, 4--1
JACKSHAFT ALIGNMENT TOOL, 5--1
FLUSH, 7--14, 7--15
JOIN TERMINAL, 2--9
FLYWHEEL LOCKING TOOL, 28, 5--11
FUSE, RESETTABLE, 20A, 1--4, 5--13
G
GAS, CALIBRATION (WITH ADAPTER), 7--4
JUMPER, PC MODE, 2--11
JUMPER, CONFIGURATION, 2--11
K
KIT, STATIC DISSIPATE, 2--4
KIT, TEST LEADS, 2--2
GASKET, 6--3, 6--4
L
GAUGE, CALIBRATION, 2--4
GAUGE, BELT TENSION, 5--2
GAUGE, COMPOUND, 6--2
GAUGE, MAGNEHELIC , 5--1
GAUGE, SHEAVE, 5--9
LEADS, 5--5
LEAK DETECTOR, 6--6, 6--18
LEAK DETECTORS, 7--14
LICENSE, 2--20
GREASE, LITHIUM BASE, 7--1
LIFTING DEVICE, 5--11
GREASE, N--2, 7--1
LIFTING TOOL, GENERATOR,VECTOR, 29, 5--11
GREASE, SRI--2, 7--1
LIGHT BULBS, 2--11
GUIDE TOOL, INSTALLATION, 5--8
LOW SIDE GAUGE, COMPOUND , 6--1
Index --2
Alphabetical Index
M
MAIN BEARING EXTRACT TOOL, 3--27
Q
QUICK START, COMPRESSOR, 1--4, 5--13
MAIN BEARING INSTALL TOOL, 3--27
R
MAIN BEARING INSTALL TOOL , 3--26
MANIFOLD GAUGE SET, 6--1
METER, COOLANT REFRACTOMETER, 26, 5--13
METER, MEGOHMETER, 2--1
MICRO CONNECTOR PIN TOOL, 2--5
RAIN CAP -- FLIP TOP, 5--12
REAMER ROD, 6--5
RECOVERY UNIT, REFRIGERANT, 6--15
MIRROR, INSPECTION, 5--10
RECOVERY UNIT, REFRIGERANT -- 230/240VAC,
6--15
MULTIMETER, DIGITAL, 2--1, 2--2
RED INSULATING VARNISH, 2--17, 7--9
REMOTE TEMPERATURE HARNESS, 2--14
O
REMOVAL BRACKET, VECTOR GENERATOR,
3--27, 5--11
O--RINGS, 6--4
REMOVAL TOOL, 2--8, 2--9
OIL, 7--1, 7--2, 7--3, 7--5, 7--6, 7--7, 7--8, 7--9, 7--10
REPLACEMENT PAPER ROLLS, PACK OF 5, 2--15
OIL DRAIN TOOL (X2), 3--28
RIVNUT TOOL, FRAME REWORK, 5--10
OIL DRAIN TOOL VECTOR 2100, 3--28
OIL FILTER KIT, 6--11
ROD FOR SERVICING SELF--ADJUSTING IDLERS,
5--5
OIL FILTER KIT,BUS, 6--14
RUBBER BANDS, 5--2
OIL TEST KIT, 7--15
S
OIL, COMPRESSOR -- 50PAG, R134A, 1QT CAN,
7--6
OIL,COMPRESSOR, PAG (FOR A--6
COMPRESSOR), 7--4
OIL,COMPRESSOR, PAG, 7--4
S6155 , 3--26
SANITIZER -- COIL, 7--12
SEAL DRIVER, 5--7
SEAL PILOT, 5--7
P
SEAL TOOL, 3--25
SEALANT, PIPE FITTINGS (134A), 7--6
PAINT, 7--8, 7--9
SENSOR, REPLACEMENT, 6--13
PAINT, HORIZON GREEN, 7--11
SENSOR, THERMOMETER, 5--4
PAINT, SEA SPRAY GREEN, 7--10
SHIM, VECTOR GENERATOR SERVICE, 2--17, 29
PAINT, SEA--HORSE BLUE, TOUCH--UP, 7--8
SHRADER CORE, 3/8”,134A, 4--2, 6--18
PAPER ROLLS, 2--15
SHRADER FITTING, 4--4
PIN TERMINAL, 2--9
SIM--583, 3-- 27
PLIER, UNLOADER RING, 1--2
SIMULATOR PROBE, 2--3
PLIERS, CRIMPING, 06D TERMINALS, 1--2
SKM--5670, 27, 5--11
PLIERS, FITTING ASSEMBLY, EZ CLIP, 6--12
SKM--5671, 5--11
PLUG, 4--2
SLEEVE INSTALLER, 3--25
PRINTER, PORTABLE, 2--15
SLEEVE PULLER (5F COMPRESSORS), 1--3
PROTECTIVE CASE, 2--21
SLEEVE PULLER (5H COMPRESSORS), 1--3
PULLER, INJECTOR, 3--25
SLEEVE TOOL, SEAL, 5--7, 5--8
PULLER, MAIN BEARING, 1--3
SMOKE BOMB, 7--10
PUMP, AIR POWERED, 6--10
SOCK ADAPTER FOR YORK COMPRESSOR, 1--5
Index --3
Alphabetical Index
SOCKET TERMINAL, 2--9, 2--10, 2--11
THERMOMETER, 5--3
SOCKET, INJECTOR, 3--25
THERMOMETER, DIGITAL, POCKET, 5--3
SOCKET, SPANNER FOR ULTRA GEARBOX, 5--6
THERMOMETER, DIGITAL, POCKET, DEGREES
CENTEGRADE, 5--3
SOCKET, SPANNER NUT LARGE , 1--1
SOCKET, SPANNER NUT SMALL, 1--1
THERMOMETER, INFRARED, 5--4
SOCKET, WATER TEMPERATURE SENDER, 3--26
THREADED ROD, VECTOR GENERATOR
REMOVAL, 5--11
SOFTWARE, 2--19, 2--20
TIMING TOOL, 3--24
SOFTWARE UPLOAD KIT, 2--16
TOTALTEST KIT, 6--6, 6--11
SOFTWARE CARD PROGRAMMER, 2--10
U
SPRAYER, 7--12, 7--13
STEPPER JUMPER ASSEMBLY, 2--10
STRAP, GROUNDING, 2--4
UNIVERSAL HAND CRIMP TOOL, 2--8
STROBE LIGHT, 2--3, 28, 5--1
UNLOADER CONVERSION, 2--13
SUCTION FILTER SHELL, 6--9
T
TACHOMETER, LASER, RPM, 2--3,3-- 28, 5--5
TANK INSERT, 5--12
TAP, THREAD LEFT HANDED, 5--10
TEMPERATURE CONTROLLER SIMULATOR
MODULE, 2--3
V
VACUUM GAGE, DIGITAL, 6--13
VACUUM PUMP, 6--5
VALVE PAD BLANK--OFF, 1--5, 1--6
VALVE, PIERCING, 6--13
VISE GRIP HOLDER, 1--2
W
TEMPERATURE PROBE, 2--14, 5--4, 6--7
TEMPERATURE PROBE, AIR, 2--14, 6--8
TEMPERATURE TESTER, 4--LEAD , 2--14, 6--7
TERMINAL BOX TOOL, 1--2
TERMINAL REMOVAL TOOL KIT, 2--8
TEST LEADS, 2--2
TEST LEADS, MEGOHMETER, 2--1
TESTER, BELT TENSION, 5--2
TESTER, INJECT NOZZLE, 3--22
WIRE CRIMPER, MAC TOOLS, 2--8
WRENCH -- SIGHT GLASS, 1--6
WRENCH, COMPRESSOR OIL PAN, 1--2
WRENCH, FILTER, 3--26
WRENCH, REFRIGERATION, 6--5
WRENCH, SIGHT GLASS, 1--6
WRENCH, SPANNER, 6--14
TESTER, MICRO, 2--4
WRENCH, SPANNER FOR CLUTCH ARMATURE,
1--1
TESTER, ML2I/ML3, 2--10
WRENCH, SPANNER, FAN CLUTCH, 5--9
TESTER, STEPPER MOTOR DRIVE, 2--5
WRENCH, SPANNER, SOLENOID EVAP, 5--9
Index --4
PART NUMBER INDEX
Part Number, Page
Part Number, Page
Part Number, Page
02-00010-00, 7-1
07-00238-00, 6-5
07-00294-02, 6-2
06DA-403-844, 4-1
07-00238-01, 6-5
07-00294-05, 6-1
07-00013-02, 5-5
07-00239-00, 25
07-00294-10, 6-4
07-00013-03, 5-5
07-00240-01, 1-1
07-00294-11, 6-4
07-00015-00, 5-5
07-00241-00, 1-1
07-00295-00, 6-6
07-00036-00, 3-1
07-00242-01, 1-1
07-00296-00, 6-7
07-00046-00, 3-1
07-00242-02, 1-1
07-00297-00, 2-5
07-00054-00, 3-1
07-00243-01, 2-2
07-00298-00, 2-5
07-00140-00, 3-1
07-00243-10, 2-1
07-00301-00, 4-2
07-00140-10, 3-1
07-00245-00, 7-1
07-00302-00, 5-5
07-00176-11, 6-5
07-00247-00, 5-1
07-00303-01, 5-6
07-00177-00, 5-1
07-00247-01, 5-1
07-00303-02, 5-6
07-00177-01, 5-1
07-00249-00, 3-4
07-00304-00, 2-4
07-00179-01, 3-2
07-00250-00, 3-4
07-00307-00, 6-2
07-00179-02, 3-3
07-00252-00, 2-14
07-00307-01, 6-3
07-00179-03, 3-3
07-00253-00, 5-2
07-00307-02, 6-3
07-00179-04, 3-2
07-00253-01, 5-2
07-00307-03, 6-3
07-00179-05, 3-3
07-00254-00, 2-6
07-00307-04, 6-4
07-00179-06, 3-3
07-00256-01, 5-2
07-00307-05, 6-4
07-00179-07, 3-2
07-00257-00, 1-2
07-00308-00, 5-7
07-00179-08, 3-2
07-00259-00, 6-5
07-00309-00, 5-7
07-00179-09, 3-2
07-00260-00, 6-6
07-00310-00, 5-7
07-00179-10, 3-3
07-00261-00, 5-3
07-00311-00, 5-7
07-00203-00, 5-2
07-00262-02, 2-1
07-00313-00, 7-3
07-00205-00, 3-3
07-00263-00, 1-2
07-00314-00, 6-1
07-00206-01, 5-1
07-00264-00, 1-2
07-00315-00, 6-7
07-00212-00, 2-3
07-00265-01, 6-6
07-00316-00, 6-8
07-00220-00, 6-5
07-00266-00, 6-6
07-00317-00, 7-3
07-00223-00, 1-2
07-00267-01, 1-2
07-00318-00, 7-3
07-00224-00, 3-4
07-00268-00, 2-7
07-00319-00, 4-2
07-00226-00, 2-3
07-00270-00, 7-1
07-00320-00, 7-3
07-00227-00, 3-4
07-00273-00, 2-4
07-00322-00, 7-4
07-00228-00, 2-2
07-00274-00, 7-2
07-00322-02 7-4
07-00229-00, 2-2
07-00275-00, 7-2
07-00324-00, 5-3
07-00230-00, 2-2
07-00276-00, 5-5
07-00325-00, 7-5
07-00237-04, 6-1
07-00277-00, 2-4
07-00326-00, 2-5
07-00237-05, 6-2
07-00290-01, 2-4
07-00328-00, 7-5
07-00237-06, 6-2
07-00292-00, 7-2
07-00329-00, 2-6
07-00237-10, 6-5
07-00292-01, 7-2
07-00330-00, 2-7
07-00237-12, 6-3
07-00294-00, 6-1
07-00331-00, 6-4
07-00237-13, 6-3
07-00294-01, 6-1
07-00332-00, 7-5
Index--1
PART NUMBER INDEX
Part Number, Page
Part Number, Page
Part Number, Page
07-00334-00, 7-6
07-00396-01, 5-9
07-00438-00, 2-12
07-00333-00, 7-5
07-00397-00, 2-8
07-00439-00, 2-12
07-00335-00, 7-6
07-00397-01, 2-8
07-00440-00, 2-12
07-00337-00, 6-6
07-00397-02, 2-8
07-00445-00, 6-15
07-00339-00, 5-7
07-00397-03, 2-8
07-00449-00, 5-10
07-00340-00, 5-8
07-00397-04, 2-8
07-00450-00, 1-6
07-00341-00, 5-8
07-00397-05, 2-9
07-00453-00, 5-10
07-00342-00, 5-8
07-00397-06, 2-9
07-00455-00, 1-2
07-00343-00, 5-8
07-00397-07, 2-9
07-00456-00, 1-2
07-00344-00, 5-8
07-00397-08, 2-9
07-00457-00, 6-14
07-00345-00, 7-6
07-00397-09, 2-9
07-00458-00, 25
07-00346-00, 1-3
07-00397-10, 2-9
07-00459-00, 6-14
07-00349-00, 7-6
07-00397-11, 2-10
07-00460-00, 1-3
07-00354-00, 7-7
07-00397-12, 2-10
07-00462-00, 2-14, 6-7
07-00357-00, 5-8
07-00398-00, 2-10
07-00462-01, 2-14, 6-8
07-00359-00, 7-7
07-00399-00, 5-9
07-00462-03, 2-14, 6-8
07-00360-01, 5-6
07-00400-00, 2-5
07-00463-00, 5-2
07-00361-00, 6-16
07-00401-00, 2-7
07-00468-00, 3-5
07-00362-00, 6-16
07-00405-00, 7-8
07-00469-00, 3-5
07-00363-00, 6-16
07-00406-00, 2-19
07-00472-00, 3-5
07-00364-00, 5-9
07-00408-00, 2-10
07-00473-00, 3-6
07-00370-00, 2-7
07-00408-00SV, 2-10
07-00474-00, 3-6
07-00373-00, 7-7
07-00409-00, 5-9
07-00476-00, 5-9
07-00375-00SV, 2-5
07-00410-00, 5-9
07-00477-00, 5-10
07-00377-00, 7-7
07-00411-00, 5-10
07-00478-00, 5-4
07-00378-00, 6-10
07-00414-00, 6-13
07-00479-00, 2-17, 7-9
07-00379-00, 6-8
07-00417-00, 6-12
07-00480-00, 7-8
07-00380-00, 6-11
07-00418-00, 5-10
07-00481-00, 2-1
07-00381-00, 1-1
07-00420-00, 7-8
07-00482-00, 2-1
07-00382-00, 6-11
07-00421-00, 2-20
07-00483-00, 2-1
07-00383-00, 6-11
07-00423-00, 3-5
07-00484-00, 24
07-00383-20, 6-12
07-00424-00, 5-4
07-00485-00, 5-3
07-00384-00, 6-11
07-00425-00, 5-4
07-00486-00, 2-3, 3-7, 5-1
07-00385-00, 6-13
07-00426-00, 2-20
07-00488-00, 2-3, 3-7, 5-5
07-00386-00, 6-13
07-00427-00, 7-9
07-00489-00, 2-6
07-00387-00, 2-6
07-00429-00, 6-14
07-00490-00, 2-6
07-00388-00, 1-3
07-00430-00, 7-9
07-00491-00, 2-7
07-00391-00, 6-13
07-00432-00, 5-6
07-00492-00, 2-7
07-00392-00, 6-10
07-00434-00, 6-14
07-00493-00, 2-6
07-00394-00, 1-3
07-00435-00, 3-5
07-00494-00, 1-4, 5-13
07-00395-00, 1-3
07-00436-00, 1-2
07-00494-10, 1-4 , 5-13
Index--2
PART NUMBER INDEX
Part Number, Page
Part Number, Page
Part Number, Page
07-50001-00, 7-10
12-50150-10SV, 2-15
40-00524-00, 4-3
07-50005-00, 3-2
12-50377-01/2.5, 2-4
40-00524-01, 4-3
07-50006-00, 6-14
12-00505-71, 2-18
40-00528-00, 4-4
07-50017-00, 6-18
14-00351-00, 4-1
40-00528-02, 4-4
07-60009-00, 6-11
14-50054-00, 6-8
40-00529-00, 4-4
07-60048-00, 2-6
14-50055-00, 6-9
40-00545-00, 4-4
07-60049-00, 5-11
14-50056-00, 6-9
40-01124-00, 4-4
07-60083-00, 28, 5-11
14-50056-01, 6-9
40-01166-00, 4-4
07-60085-00, 29, 5-11
14-60043-00, 1-5
40-01166-01, 4-4
07-60090-00, 2-5
16-00037-00, 7-10
40-01184-00, 4-2, 6-18
07-60091-00, 5-11
16-03004-00P05, 2-11
40-60087-01, 4-2, 6-18
07-60111-00, 5-3
160-0010, 6-15
42-50017-00, 6-4
07-00414-01, 6-13
17-13004-00, 1-5
42-50018-00, 6-5
07-00467-00, 6-12
17-13006-00, 1-5
46-50001-00, 7-1
07-00471-00, 1-4
17-13008-00, 1-5
46-50002-00, 7-1
07-00496-00, 2-8
17-13010-00, 4-1
46-50003-00, 7-4
07-60117-00, 6-12
17-21056-00, 1-5
46-50004-00, 7-4
07-60117-10, 6-12
17-44037-00, 4-2
46-50006-00, 7-6
0TB0889, 4-1
17-44706-00, 4-2
54-00630-25, 2-17, 3-29
12-00351-06SV, 2-20
17-55013-00, 1-6
58-00869-00, 1-4
12-00400-00/XX, 2-21
18-00099-40, 1-6
58-04030-00, 6-2
12-00503-50, 2-18
20-204-244, 1-6
58-04165-00, 1-5
12-00504-50, 2-19
22-01690-00, 2-12
58-50109-00, 2-21
12-00505-52, 2-18
22-01737-00, 2-15
58-60232-00, 4-1
12-00505-53, 2-18
22-01737-04, 2-16
65-50001-00, 5-12
12-00505-70, 2-19
22-01777-03, 2-11
68-15763-00, 3-7
12-00506-50, 2-18
22-50058-00, 2-14
68-15763-01, 3-7
12-00543-01, 2-15
22-50180-00, 2-11
74-50111-00, 2-13
12-00543-02, 2-16
22-50180-01, 2-11
74-50111-01, 2-13
12-00543-03, 2-16
22-50199-00, 2-11
74-50111-02, 2-13
12-00543-04, 2-16
30-00210-00, 5-12
74-50111-03, 2-13
12-00569-51, 5-4
40-00086-04, 4-1
76-00397-01, 7-9
12-00569-52, 5-4
40-00086-06, 4-1
76-00550-00, 2-12
12-00594, 2-19
40-00519-00, 4-2
76-00669-10, 2-16
12-00615, 2-19
40-00519-01, 4-2
76-00669-20, 2-17
12-00616-00, 2-20
40-00520-00, 4-3
76-00669-21, 2-17
12-50041-50, 5-4
40-00520-01, 4-3
76-50063-00, 5-12
12-50150-01, 2-15
40-00520-02, 4-3
76-61011-00, 2-16
12-50150-02, 2-15
40-00520-03, 4-3
79-00965-00, 4-4
12-50150-03, 2-15
40-00523-00, 4-3
79-60598-00, 2-20
12-50150-04, 2-15
40-00523-01, 4-3
79-60598-20, 2-20
Index--3
PART NUMBER INDEX
Part Number, Page
Part Number, Page
Part Number, Page
86-04751-00, 3-7
AC302-458, 4-5
NU4291-08, 7-12
NU4291-05, 7-12
A
D
NU4293-04, 7-14
NU4293-75, 7-14
DD19CA061, 4-1
AC101-707, 1-1
AC101-708, 6-12
AC101-711, 6-12
AC101-723, 6-16
AC101-724, 6-16
NU4295-34, 7-12
NU4300-10, 7-14
M
NU4300-11, 7-14
MVS II - 115, 6-15
NU4300-15, 7-15
MVS II - 240, 6-15
NU4300-99, 7-15
NU4301-02, 7-15
AC101-725, 6-16
N
NU4320-W8, 7-15
AC101-727, 6-10
AC101-728, 6-10
NU4126-34, 7-12
NU4770-00, 7-12
AC101-729, 6-10
NU4126-38, 7-12
NU4771-30, 7-13
AC101-730, 6-16
NU4133-08, 7-11
NU4772-00, 7-13
AC101-731, 6-17
NU4148-08, 7-11
NU4774-00, 7-13
AC101-732, 6-17
NU4148-32, 7-11
AC101-734, 6-17
NU4171-75, 7-11
AC101-735, 6-17
NU4182-08, 7-14
AC101-736, 6-17
NU4182-24, 7-14
P903-0901, 7-10
AC101-738, 6-17
NU4182-53, 7-14
P903-1301, 7-10
AC101-739, 6-17
NU4216-92, 7-13
PH23GH012, 7-11
AC101-740, 6-18
NU4217-W3, 7-13
PH23GH017, 7-8
AC101-741, 6-18
NU4218-W3, 7-13
PH23GL012, 7-10
AC302-438, 4-5
NU4230-72, 7-15
AC302-439, 4-5
NU4291-01, 7-12
NU4371-88, 7-11
AC302-440, 4-5
P
S
S6155, 26
AC302-441, 4-5
Index--4
Carrier Transicold Division, Carrier
Corporation
Performance Parts Group
P.O. Box 4805
Syracuse, N.Y. 13221 U.S A
www.carrier.transicold.com
A member of the United Technologies Corporation family. Stock symbol UTX
©2009 Carrier Corporation D Printed in U. S. A. 0509