advertisement
ComPoint ™
The music lover’s intercom solution
Instruction Manual
2
SAFETY PRECAUTIONS
Safety Precautions
For your safety, please read and follow these precautions before installing or using this product:
➤ Read instructions. Read and understand all the applicable instructions before installing or operating the product.
➤
➤
➤
Retain documents. Keep this manual in a convenient place for reference.
Heed warnings. Be aware of all warnings on the product and in the instructions.
Follow instructions. Install and use this product only as described in the instructions. Don’t try to use this product in ways it wasn’t designed for.
➤ Install in suitable locations. Except for the ISK3 Door Station, install this product only indoors. Don’t expose interior devices to the weather or harsh environmental conditions such as continuous sunlight, excessive humidity, or rain.
➤ Keep product dry. Don’t use the product near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Also, do not handle the product when your hands are wet or damp.
➤ Avoid heat. Locate the product away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat.
➤ Use the right power. Don’t connect the system components directly to electrical line voltage. Use only the power adapter provided with the product, described in the product specifications or installation instructions, or as marked on the product.
➤
➤
Ground product properly. Make sure the product’s means of grounding or polarization is not defeated.
Keep product clean. From time to time, wipe off the product with a clean soft cloth. Don’t use abrasive materials, thinners, alcohol or other chemical solvents or materials.
➤ Avoid spills and foreign objects. Make sure liquids and objects don’t get into the product through any openings.
➤ Get professional service. Have the product serviced only by qualified service personnel when:
• Liquids have spilled or objects have fallen into the product
• The product has been exposed to rain
• The product doesn’t appear to operate normally
• The product is damaged
Don’t attempt to service the product yourself. Doing so will void the warranty.
Russound will assume no liability for failure to understand installation or operating instructions for this product or for its improper installation or use.
If you have any questions, please call Russound at 1.800.638.8055 or 603.659.5170.
TABLE OF CONTENTS
USER SECTION
Welcome to ComPoint ™ !
About this manual
What’s in your ComPoint system
ISH1 Hub
ISK1 or ISK2 Keypad
ISK3 Door Station
ISDR1 Door Strike Release Module
Using your ComPoint system
Things you’ll need to know
Paging
Intercom
Door station call
Door strike release
Listen mode
Do Not Disturb mode
Combined Listen and DND modes
INSTALLER SECTION
About this section
Product summary
ISH1 Hub
System keypads
ISK1 Basic Keypad
ISK2 Advanced Keypad
ISK3 Door Station
ISDR1 Door Strike Release Module
Device installation and trim
Keypad backlight color selection
Wiring and connections
110 punch-down connections
10
11
12
13
14
8
8
9
4
5
6–7
7
7
6
6
8–14
18
18–19
18
17
17
17
15
15–17
16
16
16
16
Speaker connections
Doorbell connections
Door strike release connections
Hub modular connections
Programming
Hub ID numbers
Doorbell chimes
Zone and door station labels
Assigning zone labels
Assigning door station labels
Viewing system information
Restoring factory settings
Programming flow charts
Detailed function descriptions
Communication priority levels
Paging
Intercom
Door station call
Door strike release
Listen mode
Audible keypad volume level indication
System busy
Do Not Disturb (DND) mode
Keypad backlight
System function test
Troubleshooting chart
REFERENCE SECTION
Technical specifications
Accessories
Warranty
28
28
29
29
29
26
26
27
29
30
31
24–25
26–29
26
23
23
23
20–25
20
20
21
22
18
19
19
19
32
33
33
3
4
USER SECTION
Introduction
Welcome to ComPoint ™ !
Thank you for choosing a Russound
ComPoint system for your home or business. While you may already be familiar with paging and intercom systems, each system works differently. We’ve designed
ComPoint for ease of operation and with a unique set of capabilities to meet your communication needs. You’ll be pleased with the way the system simplifies your life, and we’re confident you’ll enjoy using
ComPoint every day.
ComPoint integrates the following features:
System-wide paging
Perhaps you want to call the family to dinner, move your party guests to the living room, or summon everyone in the office to an important meeting. ComPoint’s paging feature allows you to do all this with ease.
You can let everybody know about an important event like a birthday or anniversary, or you can broadcast a message for someone to pick up the phone or come see you. Whatever announcement you want to make throughout your home or business, paging allows you to get the word out.
What’s more, if you’re paging an individual, that person can reply to your page from the nearest keypad.
Point-to-point intercom
One of ComPoint’s most useful functions is the intercom feature. You need to talk with someone in another room out of earshot, and you can’t leave the room you’re in. The solution? The intercom feature lets you contact the person directly, saving you steps and time.
Whenever you want to reach a particular person without disturbing the whole house or office, the intercom feature connects you to the room the person is in. You can think of an intercom session as a private conversation while paging is a public announcement. Also, intercom enables two-way conversations, whereas paging is intended for one-way communication.
Door station call and reply
With ComPoint at your service, you don’t have to run to the door every time the doorbell rings. If you can’t get to the door right away, the door station call function gives you the convenience of answering the door from any room.
At any keypad you can have a two-way conversation with the caller to find out who it is and the purpose of their visit—before you even approach the door.
Doorbell chimes
With ComPoint, you can have separate doorbell chimes for two doors. You have a choice of seven different chime tones that your installer can assign. Or you can use a separate doorbell system if you prefer.
USER SECTION
Introduction
Door strike release
Did someone in the family forget their keys?
Did a friend drop by? ComPoint offers an optional module that works with a door strike release to let you admit your visitor from any keypad without going to the door in person. Imagine the convenience of not having to leave the baby or interrupt an important task to go and open the door for your visitor.
Listen to another room
Need to keep an ear open for someone?
Wondering what the kids are doing? With
ComPoint you’re within earshot of any other room. Listen mode keeps you in touch with what’s going on in any room with a keypad.
Do not disturb
When you’ve tucked your kids into bed or you need peace and quiet in the study to concentrate, you can switch the room keypad to Do Not Disturb. This prevents all communication events from being heard in that room.
Hands free
One of the nicest features in ComPoint is the ability to reply to intercom calls without having to touch the keypad. And when the delivery person rings your doorbell, they can answer your reply without having to press the Call key again.
Integration with your music system
For even greater convenience, your
ComPoint system can share the speakers in your multiroom audio system. When active,
ComPoint switches the speakers over to the keypad amplifiers in the affected rooms, momentarily interrupting the audio program. When the activity ends, the speakers resume playing your audio program.
About this manual
This section of the manual is for you, the user. It explains what you need to know to use and enjoy your ComPoint system.
Reading these first several pages will help you get the most out of your system. As you learn, share your discoveries with others in your family or office so they too can enjoy using ComPoint.
The Installer section that follows provides more technical information and gets into the nitty gritty of how the system works. It’s intended for your installer, but you’re welcome to read it, too.
We recommend keeping this manual in a safe, accessible place so you can refer to it when you need to.
5
6
1
2
3
4
5
USER SECTION
System Components
What’s in your ComPoint system
ISH1 Hub
As the heart of the system, the hub keeps track of the zones and routes communications appropriately. It also provides your choice of chime sounds for the built-in doorbell feature, which plays chimes through the speakers in each room.
ISK1 or ISK2 Keypad
The keypads control the system and serve as your interior communication points. A simple array of keys lets you easily operate your system. In addition, each keypad contains a built-in microphone and a small amplifier to power one or two speakers.
NEWMARKET, NH USA
ISH1 15VDC
3.5A MAX
1 3
DOORBELL CHIME
GAIN
MIN
PROGRAM OPTIONS
0=DOWN / 1=UP
MAX
DOOR BELL CHIME HUB ID
1-3 = DOOR 1 CHIME
SWITCH 4 = CHIME VOLUME
UP = 50% MAX KEYPAD OUTPUT
DOWN = KEYPAD ADJUSTABLE
5-7 = DOOR 2 CHIME
8 = NOT USED
5 DOOR 1
DS1 DS2
NONE = 000
CHIME 1 = 001
CHIME 2 = 010
CHIME 3 = 011
CHIME 4 = 100
CHIME 5 = 101
CHIME 6 = 110
CHIME 7 = 111
SWITCH 1-3
HUB 1 = 000
HUB 2 = 001
HUB 3 = 010
HUB 4 = 011
HUB 5 = 100
HUB 6 = 101
# 4
RUN
UPDATE
IN
LINK
OUT
2 4 6 DOOR 2
FIRMWARE
UPDATE PORT
MADE IN CHINA
Fig. 1. ISH1 Hub
Fig. 2. ISK1 Basic and ISK2 Advanced Keypads
7
8
9
6
1
2
3
4
5
6
7
8
9
ZONE KEYS – Select and indicate zones (Basic Keypad only)
TALK KEY – Initiates outgoing communications
MICROPHONE – Picks up user’s voice for communications and ambient sounds for Listen mode
DOOR KEYS – Select and indicate door stations; also activate door strike release (Basic Keypad only)
DO NOT DISTURB KEY – Enables and disables Do Not Disturb mode
DISPLAY – Shows zone and door station labels; also indicates modes (Advanced Keypad only)
NEXT KEY – Scrolls forward through lists and installer menus on display (Advanced Keypad only)
VOLUME KEYS – Control keypad output volume
PREVIOUS KEY – Scrolls backward through lists and installer menus; also activates door release with
Next key (Advanced Keypad only)
ISK3 Door Station
Designed for outdoor placement, the door stations provide communication links to visitors outside. Each weatherproof door station contains a built-in microphone and a speaker for two-way communication and features a simple yet elegant one-key design.
USER SECTION
System Components
ISDR1 Door Strike Release Module
This optional module provides a connection point for a separate door strike release unit, making it possible to unlock the door from any keypad.
1
2
3
Fig. 3. ISK3 Door Station
1
2
3
MICROPHONE AND SPEAKER – Enable twoway communication
CALL KEY – Rings doorbell and initiates communication
WEATHERPROOF COVER – Protects internal components
Fig. 4. ISDR1 Door Strike Release Module
7
8
USER SECTION
Operation
Using your ComPoint system
ComPoint is easy and fun to use. You’ll find these instructions simple to follow. Take a little time to get familiar with them so you can start enjoying your system right away.
Things you’ll need to know
With ComPoint, we refer to areas with keypads as zones. A zone may be a single room or an area with more than one room, such as a kitchen and dining area.
Every communication has a sender and a receiver. With ComPoint, we call any zone that initiates a communication the sending zone. The zone or zones to which the communication is sent are receiving zones, even though they may reply to the initial communication. For an intercom session, the receiving zone is also the target zone.
In ComPoint, paging is the default method of communication. Different communication functions have different levels of priority.
Paging is not allowed when there is a door station call or intercom session in progress.
An intercom session is not allowed when there is a door station call or page in progress. Also, a door station call takes precedence over paging and intercom sessions and thus interrupts them.
Your ComPoint system is configured with either ISK1 Basic or ISK2 Advanced keypads. The way you use your system and the way it gives you information depends on which keypads you have. We explain how both types work.
With either keypad, pressing the Talk key sounds a ping tone in the receiving zones to announce your message. Releasing the
Talk key sounds a double ping.
If the system is already in use when you try to send a page or start an intercom session, the Talk key blinks red for 7 seconds to let you know the system is busy. Also, the
Advanced Keypad indicates Busy on its
LCD panel.
Paging
Paging lets you send an announcement throughout your home or business from any keypad. To send a page, simply press and hold the Talk key (figure 5), then speak. Release the key when you’re done speaking.
Fig. 5. Using the Talk key for paging
Your page will be heard in all zones except those that are in Do Not Disturb mode. For privacy and to avoid disturbing your neighbors, your page will not be heard at either door station.
USER SECTION
Operation
Paging (cont’d)
If a zone key is lit red on the Basic Keypad, press the key to deselect that zone before you press the Talk key to send a page.
If a zone label appears in the display on the Advanced Keypad, use the Next or
Previous key to select Page before you press the Talk key.
All keypads indicate which zone is sending a page, so you’ll know where it’s coming from. The zone indication remains for 30 seconds after the Talk key is released to simplify replying to the page.
The keypads in the receiving zones also sound a double ping when the Talk key is released. This lets you know the person sending the page is done speaking and you can reply to the page. Within 30 seconds, simply press and hold the Talk key and speak. Your reply will be heard only in the zone that sent the page.
If you wish to reply to the page after the
30-second limit, you can use the intercom function described below or a return page to send your reply.
Intercom
Unlike a system-wide page, an intercom session occurs only between two zones. To use this feature, select a target zone on a keypad. Press and hold the Talk key and speak. Release the Talk key when you’re done speaking.
On the Basic Keypad, press and release a zone key to select the target zone (figure
6). The key lights up red to indicate the zone is selected.
Fig. 6. Selecting a target zone on the Basic Keypad
If the selected target zone is in Do Not
Disturb mode, the zone key and DND key blink rapidly for 7 seconds.
On the Advanced Keypad, select a target zone by using the Previous or Next key to scroll through the list of available zones until the display shows the zone you want for the intercom session (figure 7).
If the selected zone is in Do Not Disturb mode, the display alternately shows the zone label and DND at 1-second intervals and the DND key blinks rapidly for 7 seconds.
9
USER SECTION
Operation
Door station call
A visitor can ring the doorbell and initiate a door station call by simply pressing and releasing the Call key (figure 8). When the
Call key is pressed, all keypads indicate the calling door station for 15 seconds. The D1 or D2 key on the Basic Keypad blinks red and the display on the Advanced Keypad shows Door1, Door2, or an installerassigned door label (figure 9).
10
Fig. 7. Selecting a target zone on the Advanced Keypad
Intercom (cont’d)
When the Talk key is released on the sending keypad, the receiving keypad indicates the sending zone to let you know which zone is sending. Also, both the sending and receiving keypads sound a single ping to let you know you can reply hands free within 7 seconds. After the 7 seconds, the keypads sound a double ping to signal the end of the hands-free reply period.
After the double ping, you can reply within
30 seconds by pressing and holding the
Talk key while you speak. After 30 seconds you can no longer reply, but you can start another intercom session to the zone that sent the original message.
Fig. 8. Using the Call key on a Door Station
The keypads also sound a doorbell chime, as long as they aren’t in Do Not Disturb mode and a chime option is selected on the hub. Alternatively, the door station can ring a separate doorbell.
USER SECTION
Operation station pings twice to indicate the time is up.
If more than 15 seconds have passed since the door call, you can reselect the door station and press the Talk key to start a new session. This does not ring the doorbell.
Door strike release
Fig. 9. Door call indication on Basic and Advanced keypads
Door station call (cont’d)
A door station call takes precedence over paging and intercom sessions and thus interrupts them if they’re in progress when the Call key is pressed.
If your ComPoint system includes optional ISDR1 Door Strike Release
Modules, you can activate them from a keypad to unlock the doors. The
ISDR1 itself does not unlock the door; rather, it provides a switch to control a separate door strike release unit to unlock the door.
To reply to a door station call, press and hold the Talk key on a keypad within 15 seconds and speak. Release the Talk key when you’re done speaking. When you
To activate a Door Strike Release Module from a Basic Keypad, press and hold the corresponding door station key for 3 seconds (figure 10).
release the Talk key, the door station sounds a single ping to let the caller know they can answer your reply.
Note: You must use the Talk key to reply to a door station call. For your privacy,
ComPoint doesn’t allow a hands-free reply to a door station call.
After you reply to a door station call, the caller has 7 seconds to answer your reply hands free. After 7 seconds, the door
Fig. 10. Releasing a door strike on the Basic Keypad
11
USER SECTION
Operation
Door strike release (cont’d)
The module then activates for 3 seconds and the keypad and door station confirm activation with a buzz tone.
To activate the Door Strike Release Module from an Advanced Keypad during a door call, press and hold both the Previous and
Next keys at the same time for 3 seconds.
The module then activates for 3 seconds and the keypad and door station sound a buzz tone to confirm activation.
To activate the Door Strike Release Module from an Advanced Keypad when there is no current door call session, first press the
Previous or Next key to scroll through the list to the door label (figure 11). Then press and hold both keys for 3 seconds.
Listen mode
You can use your ComPoint system to continuously listen to any single zone from one or more other zones. To do this, first turn on a keypad microphone in the zone you want to listen to, then select that zone on one or more other keypads.
Other communication events have priority over Listen mode but only temporarily interrupt it.
To turn on a zone microphone, select that zone on its own keypad. The Talk key lights up red to indicate the keypad’s microphone is active. On a Basic keypad, the zone key blinks (figure 12) and on an Advanced
Keypad, the zone label changes to MicOn after 2 seconds (figure 13). Note: Only one zone microphone can be on at once.
Door1 Door1
12
1 2
Fig. 11. Releasing a door strike on the Advanced Keypad
Fig. 12. Basic Keypad Microphone On indication
Fig. 13. Advanced Keypad Microphone On indication
Listen mode (cont’d)
To listen to the zone with the active microphone from a Basic Keypad, press the zone key (figure 14). The key blinks three times and then remains lit red to indicate selection of the zone with the active microphone.
USER SECTION
Operation gle between the zone label and Listn as long as the active zone is selected.
To disable Listen mode from either type of keypad, press any key other than Volume
Up or Volume Down in the zone you are listening to. Listen mode cannot be disabled from any other zone. The volume keys are reserved for adjusting the keypad volume.
Listn
Fig. 14. Selecting Listen mode on the Basic Keypad
To listen to the zone with the active microphone from an Advanced Keypad, press the Previous or Next key to select the zone
(figure 15). The display will alternately tog-
Fig. 15. Selecting Listen mode on the Advanced Keypad
Do Not Disturb mode
The Do Not Disturb (DND) feature allows you to prevent pages, intercom sessions, door station calls, and doorbell chimes from being heard in a zone. Thus, you can use DND mode to prevent interruption of a multiroom audio program in that zone.
To turn on DND mode, press and release the DND key (figure 16). The DND key lights up red to indicate the zone is in
DND mode.
13
14
USER SECTION
Operation
Combined Listen and DND modes
You can use DND mode on a keypad you are listening to in Listen mode. This way the zone you’re listening to won’t be disturbed by the doorbell or other communication events.
To set up a zone for Listen mode and DND, first activate the keypad’s microphone by selecting that zone on the keypad. Then turn on DND key.
Fig. 16. Selecting Do Not Disturb mode
Do Not Disturb mode (cont’d)
The Talk key and DND key light up red to indicate the keypad’s microphone is on and the zone is also in DND mode. On a Basic
Keypad, the zone key also blinks. On an
Advanced Keypad, the display also shows
MicOn .
To cancel DND mode, press any key on the keypad other than Volume Up or Volume
Down.
Another Advanced Keypad listening to that zone alternately displays the zone label,
Listn , and DND.
Enjoy!
With ComPoint, we’ve created a versatile communication system that we hope will fit right in with your lifestyle. We’re sure you’ll find ComPoint very useful and a pleasure to use.
INSTALLER SECTION
Product Summary
About this section
This section of the manual provides technical information for installing and programming the
ComPoint system. It also provides detailed functional descriptions of the system components.
Product summary
The ComPoint system uses one or more central hubs, each of which supports up to 6 keypads.
Each keypad is addressable by its own unique
ID number assigned by the hub.
ComPoint connects with CAT-5 cable, which conveys power, ground, audio bus, and data between the components. The system end-toend length limit for the CAT-5 cable is 250 feet
(76 m).
The system can include one or two door stations connected to hub #1. Each door station has its own unique ID number, permanently assigned in the system firmware.
Each door station may also have a door strike release module wired in line between the hub and the station.
Simple system programming is required to assign the hub ID numbers, doorbell chimes, and when ISK2 Advanced Keypads are used, zone and door labels.
ISK2
ISH1
ISPS
ISK3 ISK3
ISDR1 ISDR1
Fig. 17. Six-zone ComPoint system with Advanced Keypads and Door Strike Release Modules
15
INSTALLER SECTION
Product Summary
16
ISH1 Hub
As the central controller for the ComPoint system, the ISH1 Hub performs all communications routing. It addresses each keypad by sending a message on the status wire in the CAT-5 cable to give the keypad its own ID number according to the port it’s connected to.
The hub has 6 zone keypad ports. Up to 6 ISH1
Hubs can be linked together for a maximum of
36 zones. With multiple hubs, each hub must be assigned a unique ID number during installation.
The hub also has ports for 2 door stations. In a system with multiple linked hubs, only the hub with ID number 1 supports the door stations.
A separate doorbell chime tone can be selected on hub 1 for each door. These chime selections take effect for the entire system and play through all the zone keypads.
The hub’s firmware contains a list of zone labels for display on the ISK2 Advanced Keypads. The labels are assigned to zones by the installer and stored in nonvolatile memory within the hub.
The ISH1 hub uses an external power supply to conserve chassis space. It also has a port for updating the system firmware from a computer.
System keypads
ComPoint keypads are designed to be simple, intuitive interfaces for the user. Each model has a Talk key, volume keys, and a DND key for setting the zone in Do Not Disturb mode. Both models have installer-selectable amber or green backlighting that turns on when the system is used and turns off after the system is inactive for 60 seconds. A built-in microphone with automatic gain control picks up the user’s voice.
The keypads require external speakers, which are driven by the keypad amplifiers for communications. By using built-in speaker relays, the keypads can share the speakers used in a multiroom audio system. When ComPoint activates, the relays switch the speakers to the keypad amplifiers in the affected zones, momentarily interrupting the audio pprogram. When the activity ceases, the speakers are switched back to the audio system.
In the absence of a multiroom audio system, or in zones that are not shared with an audio system, the keypads can be connected directly to in-wall, in-ceiling, or surface-mounted speakers through concealed wiring.
The keypad amplifier is monaural, but the relay passes stereo signals from the audio system to the speakers.
The keypad volume keys adjust the listening level for communications by controlling the keypad’s amplifier output. They have no effect on the room volume for a connected audio system.
The volume keys signal the hub to send a ping tone as an audible cue for the volume level when there is no communication taking place.
Once the volume adjustment reaches either end of the range, the ping tone no longer sounds.
ISK1 Basic Keypad
The ISK1 Basic Keypad is designed for use in a system with up to six zones, since it cannot indicate or select zones other than 1 through 6.
Pressing a zone key selects a target zone for an intercom session.
Certain keys change to red to indicate zone or door station selection, incoming page or intercom, door station call, or system busy. When another zone originates a page or intercom session, that zone is indicated by a red-backlit zone key on the ISK1.
ISK2 Advanced Keypad
The ISK2 Advanced Keypad has enhanced features to provide more user feedback and support a larger system than the ISK1. It uses a 5character LCD text display to show zone and door station labels and other information.
INSTALLER SECTION
Product Summary/Installation
ISK2 Advanced Keypad (cont’d)
One of the benefits of the Advanced Keypad is unrestricted intercom on large systems (7 to 36 zones), since the ISK2 is able to select any of the zones by label. The zone and door station labels are dynamically served from the hub and listed in alphabetical order to appear on the keypad display. A Page label is included in the list as the default selection when the system is inactive and the Talk key is pressed.
On the ISK2, the target zone for an intercom session is selected by scrolling through the zone list. Pressing and holding the Previous or
Next key scrolls through the list with a half-second delay between zone labels.
A bar graph on the display indicates the zone volume level visually in conjunction with the audible ping tones. A small pushbutton on the front edge of the keypad is used to enter a setup mode to assign labels to the zones.
ISK3 Door Station
Unlike the Basic and Advanced Keypads, the
ISK3 Door Station has only one key and contains an internal speaker. Amplification for the speaker is built in as with the keypads but there is no speaker interrupt relay. A potentiometer allows adjustment of the speaker volume level.
The ISK3 also provides contacts for closing a standard doorbell circuit. These close for a minimum of 4 seconds to activate an existing doorbell or other device.
ISDR1 Door Strike Release Module
The optional ISDR1 Door Strike Release Module provides relay contacts for activating a door strike release obtained from another source.
The module connects in the CAT-5 line between a hub and an ISK3 door station. The ISDR1 can be located anywhere in the CAT-5 line, though it would be preferable to have it close to the door.
The ISDR1 obtains its operational power from the hub. The separate door strike release must receive power from its own source.
The ISDR1 passes signals on all leads of the
CAT-5 cable except one which is used to activate the module from the hub upon receiving a command from a keypad.
By providing a normally closed (NC) relay contact in addition to the normally open (NO) and common contacts used for the door strike release activation, the ISDR1 can be used for other applications where a versatile relay is needed. The ISDR1 can be activated by providing 15 VDC between two of the eight positions in the 110 punch-down input connector.
Device installation and trim
The ISH1 Hub is designed for surface mounting or installation in a structured wiring panel. It should be located near an electrical outlet.
The ISK1 and ISK2 Keypads are designed to install in standard US electrical plastic wall boxes with an internal volume of at least 18 cubic inches (295 cm 3 ). Each keypad occupies a single gang and accepts a Decora ® wall plate.
For the best accessibility, viewability, and microphone reception, we recommend installing the keypads at a standard thermostat height of 58 to 60 inches (1.5 m). This may vary according to personal preferences or requirements.
The ISK3 Door Station installs in a standard single-gang US electrical deep plastic wall box with an internal volume of at least 22 cubic inches
(360 cm 3 ). It has its own weather-resistant front plate and thus needs no other cover plate.
The ISDR1 Door Strike Release Module is a surface-mount device. It should be located in an accessible area near the door, such as an attic, basement, or closet space between the door station and the hub. The ISDR1 connects to a door strike release unit, which in most cases would be installed by a security contractor.
17
18
INSTALLER SECTION
Installation
Keypad backlight color selection
Each ComPoint keypad can be set to either amber or green backlighting, selected by a miniature slide switch on the bottom edge of one of the circuit boards (figure 18).
ISK1
BR BR/W G G/W O O/W BL BL/W
Amber Green
ISK2
Fig. 18. Keypad backlight color selector switch
Wiring and connections
ComPoint system components connect with
CAT-5 cable. Run CAT-5 from the hub location to every keypad and door station location. If you are installing ISDR1 modules, loop the door station cables through the module locations.
Each keypad in the system requires one or two external speakers. If the ComPoint system is sharing speakers with an audio system, loop the speaker cables through the keypad locations. If dedicated speakers are being used, run the speaker cables to the keypads.
When running CAT-5 and speaker cables, avoid
AC power wiring. If you must run the cables parallel to electrical wiring, space the cables at least two feet (0.6 m) from the AC power lines.
110 punch-down connections
The keypads, door stations, and door strike release modules have 110 punch-down connectors for the CAT-5 cables. Connect the wires as shown in figure 19.
BR BR/W G G/W O O/W BL BL/W
BR BR/W G G/W O O/W BL BL/W
Fig. 19. 110 punch-down connection
The keypad wire functions are as follows:
Wire Color
Brown
Brown/White
Green
Green/White
Orange
Orange/White
Blue
Blue/White
Function
Audio +
Audio –
Status
Ground
Ground
+ 15 VDC
Com A
Com B
Speaker connections
Each keypad also has an 8-pole screw-terminal connector for accessing the internal speaker relay. This connector is typically used for connecting the zone speakers in a multiroom audio system. In a zone where the ComPoint system does not share speakers with an audio system, connect a dedicated speaker or pair of speakers to the output terminals.
Note: Both speaker output channels must be connected, since they are wired in series. If you are using only one dedicated speaker, connect the speaker to one channel and connect a shorting jumper or a 2-watt power resistor of up to 8 ohms to the other channel. If the CAT-5 cable to the keypad is short, a jumper will suffice. If the CAT-5 is long, use a resistor instead to reduce the load on the keypad amplifier.
Be sure to observe polarity when connecting the speaker wires. The standard color code for
4-conductor speaker cable is as follows:
INSTALLER SECTION
Installation
To ISK3
Door Station
Speaker connections (cont’d)
Wire Color
White
Green
Black
Red
Polarity
Left +
Left –
Right –
Right +
OUT TO SPEAKERS IN FROM AMPLIFIER
L+ L- R - R+ L+ L- R- R+
Fig. 20. Speaker connection to keypad
Doorbell connections
ComPoint can either provide a doorbell function or operate a separate doorbell system. To use a separate doorbell, connect each door station to the doorbell as shown in figure 21 or the doorbell system instructions.
Doorbell
Transformer
Doorbell
To door strike release unit
From ISH1 Hub
Fig. 22. Door Strike Release Module connections
Hub modular connections
The hub has 8-pole modular jacks for keypad and door station connections. The keypads connect to ports 1 through 6, and the door stations connect to DOOR1 and DOOR2. These connections must be made according to the T568A standard as shown in figure 23.
The hub also uses modular jacks for the link ports. You may use any 8-pole straight-through patch cable to link hubs together.
Fig. 21. Doorbell connection to door station
Door strike release connections
The door strike release module has 110 punchdown connectors for the hub and door station cables. It also has screw terminals for its relay contacts that accept up to 14 AWG stranded wire. Figure 22 shows the connections.
Fig. 23. 8-pole modular T568A connection
19
INSTALLER SECTION
Programming
System programming
All system programming resides in the ISH1
Hub. For a six-zone system with ISK1 Basic
Keypads, programming consists only of setting the doorbell chimes. For a system with ISK2
Advanced Keypads, programming includes assigning zone and door station labels. For a system with more than six zones, programming includes setting hub ID numbers.
20
Fig. 24. DIP switches on ISH1 Hub
The ISH1 Hub has DIP switches for setting the hub ID number and doorbell chime assignments.
The hub’s firmware contains lists of zone and door station labels for display on the ISK2
Advanced Keypads. These labels are assigned by using a connected ISK2 keypad.
With multiple hubs, the label settings are initially stored in the hub to which the keypad is connected. Upon exiting the programming procedure, the settings are copied to the other hubs.
Hub 1 serves as the master hub for storing all zone and door label settings. Whenever hub 1 is powered up, its settings are copied to the other hubs. Accordingly, hub 1 should be powered up last whenever the system power is cycled.
Hub ID numbers
In a system with multiple ISH1 Hubs, each hub must have a unique ID number. This is manually assigned on the 4-switch HUB ID DIP before the system is powered up. To assign the ID number, set switches 1 through 3 as shown in table 1.
Hub ID Switch Settings (0 = Down, 1 = Up)
Hub ID
Switches
FW*
1 2 3 4
Hub 1 0 0 0 1
Hub 2
Hub 3
Hub 4
Hub 5
Hub 6
0
0
0
1
1
0
1
1
0
0
1
0
1
0
1
1
1
1
1
1
*Switch 4 is for firmware updates
(0 = Update Mode, 1 = User Mode)
Table 1. Hub ID switch settings
Switch 4 enables a programming mode for updating the system firmware. Leave this switch in the up position for system operation.
Doorbell chimes
A single 8-switch DIP assigns doorbell chimes for both door stations. Switches 1 through 3 select the chime for door 1 and switches 5 through 7 select the chime for door 2. There are 7 chime options, with a setting for no chime when a separate doorbell system is used. To select the chimes, set the switches as shown in table 2.
Doorbell Chime Switch Settings (0 = Down, 1 = Up)
Door 1
Switches
CV* Door 2
1 2 3 4 5 6 7 8
None
Chime 1
0
0
0
0
0
1
0/1
0/1
0
0
0
0
0
1
–
–
Chime 2
Chime 3
Chime 4
Chime 5
Chime 6
Chime 7
0
0
1
1
1
1
1
1
0
0
1
1
0
1
0
1
0
1
0/1
0/1
0/1
0/1
0/1
0/1
0
0
1
1
1
1
1
1
0
0
1
1
0
1
0
1
0
1
–
–
–
–
–
–
*Switch 4 is for chime volume
(0 = Keypad Adjustable, 1 = 50% Keypad Maximum)
Table 2. Doorbell chime switch settings
INSTALLER SECTION
Programming
Bed1
Bed2
Bed3
Bed4
Bed5
Bilrd
BkYrd
Blcny
Cellr
Court
Deck
Den
Zone Label
Alcov
Atrm
Attic
Baby
Bar
Basmt
Bath
Bath2
Bath3
BDeck
Doorbell chimes (cont’d)
Switch 4 selects how the chime volume level is managed. Setting the switch to 1 (up) sets the chime volume level to a fixed level at 50% of the maximum keypad output in all zones. This causes the chime to play at the same level in all zones. Setting the switch to 0 (down) allows the chime volume to be determined by the keypad volume level setting in each zone independently.
Switch 8 is currently not used.
The ISH1 Hub also has a gain control for setting the overall volume of the doorbell chime through the system. This can be used to adjust the chime level relative to the communication level.
Note: In a system with multiple linked hubs, only the settings on hub 1 affect the doorbell chime assignments and volume level, since the door stations connect only to hub 1. Because the settings take effect immediately, the doorbell chimes can be set at any time. There is no need to cycle the power after setting them.
Zone and door station labels for Advanced
Keypads
The ISK2 Advanced Keypad shows which zone or door station is selected by displaying a zone or door station label. The default zone labels are Zn#1 through Zn#36, based on the hub and port numbers the keypads are connected to.
The default door station labels are Door1 and
Door2. You can assign zone labels from table 3 and door station labels from table 4 to replace the default labels. The hubs retain label assignments in nonvolatile memory so they won’t be affected if the system is powered down.
Room Name
Alcove
Atrium
Attic
Baby Room
Bar
Basement
Bathroom
Bathroom 2
Bathroom 3
Back Deck
Bedroom 1
Bedroom 2
Bedroom 3
Bedroom 4
Bedroom 5
Billiard Room
Back Yard
Balcony
Cellar
Courtyard
Deck
Den
Zone Label Room Name
Dine
Entry
Dining Room
Entry Way
Grage
Great
Guest
Gym
Jcuzi
KBed
Kids
Kitch
Famly
Foyer
FtYrd
Galry
Game
Gardn
GBath
GBed
Laund
Libry
LivRm
Lobby
Family Room
Foyer
Front Yard
Gallery
Game Room
Garden
Guest Bath
Guest Bed
Garage
Great Room
Guest Room
Gym
Jacuzzi
Kids Bed
Kids Room
Kitchen
Laundry
Library
Living Room
Lobby
Table 3. Assignable zone labels for ISK2 Advanced Keypads
Pool
Porch
RecRm
Sauna
SDeck
Shop
SitRm
State
Study
SunRm
Wkshp
Zone Label
Loft
MBath
MBed
Nurse
Offc1
Offc2
Parlr
Patio
Play
Pntry
Room Name
Loft
Master Bath
Master Bed
Nursery
Office 1
Office 2
Parlor
Patio
Play Room
Pantry
Pool
Porch
Rec Room
Sauna
Side Deck
Shop
Sitting Room
State Room
Study
Sun Room
Workshop
21
INSTALLER SECTION
Programming
22
Zone and door station labels (cont’d)
Door Label
BDoor
FDoor
Gate
Grage
SDoor
SvcDr
Door Name
Back Door
Front Door
Gate
Garage
Side Door
Service Door
Table 4. Assignable door labels for ISK2
To assign labels you must have all hubs linked together with unique ID numbers (if the system has multiple hubs) and an ISK2 Advanced
Keypad connected to any hub. You can use the same keypad to assign labels for the entire system. Also, the system must be powered up.
Assigning zone labels
To assign zone labels, follow these steps (or the
Zone Name Procedure flow chart on page 24):
1. Remove the wall plate if it’s installed. Press and release the Setup button on the right edge of the keypad (figure 25) to enter the main menu.
The display shows
ZName (ZONE NAME).
2. Press the Talk key to enter the Zone Name procedure. The display shows Zn#? to prompt you to select a zone number.
3. Press the Talk key again for the next sequential zone to be assigned or use the Volume Up or
Fig. 25. ISK2 Setup Button
Volume Down key to select a specific zone. You can press and hold the key to scroll through the list of zones with a half-second delay between items. Stop at the desired zone number.
4. Press and release the Talk key. The display shows
Name? to prompt you to assign a zone label.
5. Use the Volume Up or Volume Down key to select a label from the list of zone labels. You can press and hold the key to scroll through the list of zone labels with a half-second delay between items.
Stop at the desired label.
6. Press and release the Talk key to save the selection. The display shows Zn#? to prompt you to select the next zone.
7. Repeat steps 3 through 6 for the remaining zones.
Press and release the Setup button to exit the procedure. You can then go to the Door Name
Procedure by pressing the Next key or press the Setup button again to exit the main menu.
Note: If you aren’t sure which zone an ISK2 keypad is connected to, you can find out by observing the keypad’s display when powering up the system. When a hub is powered up, each keypad connected to that hub briefly indicates
Page, then indicates the port and hub number to which it is connected. For example, an indication of P4:H2 shows the keypad is connected to port 4 on hub 2. This indication remains for 3 seconds, then reverts to Page.
Zones are numbered sequentially starting with hub 1, port 1. Table 5 shows zone numbers and port assignments.
4
5
6
7
8
Zone
1
2
3
9
10
11
12
Port
P1:H1
P2:H1
P3:H1
P4:H1
P5:H1
P6:H1
P1:H2
P2:H2
P3:H2
P4:H2
P5:H2
P6:H2
Zone
13
14
15
16
17
18
19
20
21
22
23
24
Table 5. Zone port assignments
Port
P1:H3
P2:H3
P3:H3
P4:H3
P5:H3
P6:H3
P1:H4
P2:H4
P3:H4
P4:H4
P5:H4
P6:H4
28
29
30
31
32
Zone
25
26
27
33
34
35
36
Port
P1:H5
P2:H5
P3:H5
P4:H5
P5:H5
P6:H5
P1:H6
P2:H6
P3:H6
P4:H6
P5:H6
P6:H6
INSTALLER SECTION
Programming
Assigning door station labels
To assign labels to the door stations, follow these steps (or the Door Name Procedure flow chart on page 24):
1. Press and release the Setup button on the right edge of the keypad (figure 25) to enter the main menu. The display shows ZName (ZONE NAME).
2. Press and release the Next key once. The display shows DName (DOOR NAME).
3. Press the Talk key to enter the Door Name procedure. The display shows Dr#? to prompt you to select a door station number.
4. Press the Volume Up or Volume Down key to select a door station.
5. Press and release the Talk key. The display shows
Name? to prompt you for a door station label.
6. Use the Volume Up or Volume Down key to select a label from the list of door station labels. You can press and hold the key to scroll through the list of zone labels with a half-second delay between items. Stop at the desired label.
7. Press and release the Talk key to save the selection. The display shows Dr#? to prompt you to select the other door station.
8. To assign a label to the other door station, repeat steps 4 through 7.
Press and release the Setup button once to exit the procedure or twice to exit the main menu.
Once you have assigned the hub ID numbers
(for systems with multiple hubs), doorbell chimes, zone labels, and door station labels, the system is fully programmed.
Viewing system information
The System Info Menu allows you to check the build time, build date, and version of the hub’s firmware. This is useful to see whether the hub has the latest firmware version. To view system information, follow these steps (or the System
Info Menu flow chart on page 25):
1. Press and release the Setup button on the right edge of the keypad (figure 25) to enter the main menu. The display shows ZName (ZONE NAME).
2. Press and release the Next or Previous key twice.
They display shows SInfo (SYSTEM INFO).
3. Press the Talk key to enter the System Info menu.
The display shows BTime (BUILD TIME).
4. Press and release the Talk key to view the build time, or
5. Press the Next key to go to BDate (BUILD
DATE).
6. Press and release the Talk key to view the build date, or
7. Press the Next key to go to Ver (VERSION).
8. Press and release the Talk key to view the version.
Press and release the Setup button once to exit the procedure or twice to exit the main menu.
Restoring factory settings
The Factory Initialization Procedure resets the zone and door station label assignments and zone volume settings to the original factory defaults. This procedure affects the hub to which the keypad is connected, and initializing hub 1 also resets the entire system.
To restore the factory settings, follow these steps (or the Factory Initialization Procedure flow chart on page 25):
1. Press and release the Setup button on the right edge of the keypad (figure 25) to enter the main menu. The display shows ZName (ZONE NAME).
2. Press and release the Next key three times or the
Previous key once. The display shows FInit
(FACTORY INIT).
3. Press the Talk key to enter the Factory Initialization
Procedure. The display shows Sure? (ARE YOU
SURE?).
4. Press the Volume Up or Volume Down key to select Yes.
5. Press the Talk key to initialize the system. The display shows Please Wait, followed by Cycle
Power.
6. Cycle the power on the hub to which the keypad is connected.
23
24
INSTALLER SECTION
Programming
Press and release
Setup button
ISK2 Keypad Zone Name Procedure
Setup button on right edge of keypad behind cover plate
ZONE
NAME
DOOR
NAME
SYSTEM
INFO
FACTORY
INIT
Main
Menu
Zn#?
Name?
Press and release
Setup button
ISK2 Keypad Door Name Procedure
Setup button on right edge of keypad behind cover plate
ZONE
NAME
DOOR
NAME
SYSTEM
INFO
FACTORY
INIT
Main
Menu
Dr#?
Name?
Enter menu/Up one level Next/Previous item Select parameter Enter
INSTALLER SECTION
Programming
System Info Menu
Using ISK2 Keypad
Press and release
Setup button
ZONE
NAME
Setup button on right edge of keypad behind cover plate
DOOR
NAME
SYSTEM
INFO
FACTORY
INIT
Main
Menu
BUILD
TIME
BUILD
DATE
VERSION
System Info
Menu
Press and release
Setup button
Time Date Version
Factory Initialization Procedure
Using ISK2 Keypad
Setup button on right edge of keypad behind cover plate
ZONE
NAME
DOOR
NAME
SYSTEM
INFO
FACTORY
INIT
Main
Menu
ARE YOU
SURE?
No
Yes
Please
Wait
Cycle
Power
Enter menu/Up one level Next/Previous item Select parameter
This procedure returns the system to its factory settings
Enter
25
26
INSTALLER SECTION
System Functions
Detailed function descriptions
ComPoint routes communications by switching its audio bus to the keypads and door stations.
All switching takes place in the hub(s). The hub switches the bus to either the microphone or the amplifier in a keypad or door station, depending on the direction of the communication.
For example, when you start an intercom session, the system switches the bus to the microphone in the sending keypad and the keypad amplifier in the selected receiving zone. For the reply, it reverses the connection so the microphone in the receiving keypad is connected to the amplifier in the sending keypad.
Communication priority levels
Certain communication events take priority over others for proper system operation. Each function has a priority level based on its application.
If two identical levels of communication overlap, the first to occur has priority.
System functions have the following priorities:
Door station call
Paging
Intercom
Listen mode
Top priority
(supersedes all other events)
Intermediate priority
Low priority
Paging
Paging is the default system function. To send a page, all one needs to do is press and hold the
Talk key and speak, as long as the keypad is not indicating a selected zone or door station.
Since a page is a system-wide broadcast, no zone selection is necessary.
When a page is sent, the audio bus connects to the microphone in the sending zone and the amplifiers in all other zones that are not in DND mode. All keypads indicate which zone is sending the page for 30 seconds after the Talk key in the sending zone is released.
During this 30-second time frame, anyone in a receiving zone can reply to the page by holding in the Talk key and speaking. This switches the audio bus to the microphone in the receiving zone and the amplifier in the sending zone. The reply is heard only in the sending zone.
With paging, pressing the Talk key causes a single ping tone to sound in the receiving zones to signal the beginning of the announcement.
Releasing the Talk key sounds a double ping to signal the end of the announcement.
Zones in DND mode don’t receive a page audio signal but do indicate the sending zone. Also, pages are never sent to door stations.
Thus, paging is not allowed when the audio bus is being used for an intercom session or a door station call. Similarly, an intercom session is not allowed when a door call or page is in progress.
However, paging and intercom can interrupt Listen mode, and door station calls can interrupt all other communications. DND mode blocks all levels of communication to a zone in that mode.
Intercom
Intercom is a point-to-point communication that involves only two zones, unlike a page which is system wide. For ease of use, the intercom function allows hands-free replies as well as manual replies with the Talk key.
INSTALLER SECTION
System Functions
Intercom (cont’d)
The intercom function requires first selecting a target zone. This is done by pressing a zone key on the ISK1 Basic Keypad or scrolling to a zone label on the ISK2 Advanced Keypad. After selecting a zone, the user may press the Talk key to begin communication.
If an invalid zone (one that has no keypad) is selected on an ISK1 Basic Keypad, the zone key blinks rapidly for 7 seconds. Pressing another zone key selects another zone. After a valid target zone is selected, pressing the same zone key deselects it.
If a zone in DND mode is selected on an ISK1
Basic Keypad, the zone key and DND key blink rapidly for 7 seconds when the Talk key is pressed.
With the ISK2 Advanced Keypad, only valid zones (ones with keypads connected) appear in the zone list on the display. If a zone in DND mode is selected, the display alternately shows the zone label and DND at 1-second intervals and the DND key blinks rapidly for 7 seconds. A selected zone can be deselected by selecting
Page or another zone.
When receiving an intercom message, the target keypad indicates the sending zone. This indication remains for a 37-second reply period after the Talk key on the sending keypad is released.
There are two ways to reply to an intercom message with either type of keypad: a handsfree reply within 7 seconds and using the Talk key within 30 seconds thereafter. When the Talk key on the sending keypad is released, both the sending and target keypads sound a single ping and the target keypad permits a hands-free reply by activating its microphone for 7 seconds. During this period the Talk key on the target keypad is lit red to indicate the microphone is active.
After the 7 seconds, a double ping in both the sending and target zones indicates the end of the hands-free reply period. A reply may still be made by pressing and holding the Talk key within the next 30 seconds. After the 30 seconds, a reply can no longer be made, but a person in the receiving zone can start a new intercom session to the original sender.
Each time a Talk key in either zone is released, a single ping is heard in the other zone and the
7- and 30-second reply periods are renewed.
Door station call
Communication with the door stations is similar to an intercom session, though there are significant differences. First, a door station has no ability to select a target zone. Instead, it simply rings the doorbell and a person in any zone can reply. Second, for privacy reasons the system doesn’t allow a hands-free reply to a door station call from the interior keypads. The reply can be made only by pressing and holding the
Talk key.
When the Call key on a door station is pressed, each hub instructs all connected keypads that aren’t in DND mode to activate their speaker relays and connects the audio bus to their amplifiers. If a doorbell chime is selected on hub 1, the chime is played through the speaker outputs on those keypads and through the internal speakers in the door stations.
27
28
INSTALLER SECTION
System Functions
Door station call (cont’d)
Pressing the Call key also causes the doorbell contacts to close for a minimum of 4 seconds to activate a separate doorbell or other device connected to the door station. The actual time varies with the doorbell selection on hub 1; the contacts remain closed for the duration of the selected chime.
Also, all keypads indicate which door station is calling, regardless of whether or not they’re in
DND mode. The indication remains for 15 seconds, during which the door station is selected at each keypad for reply.
Within the 15 seconds, a person at any keypad can then speak with the person at the door while holding in the Talk key. If the 15 seconds pass before the Talk key is pressed, the person inside will need to first select the door station on the keypad and then press the Talk key to start a new session. This will not activate the doorbell chime.
When a door call is answered from inside, the release of the Talk key at the keypad triggers a single ping at the door station to let the caller know they can reply. The person at the door station has a 7-second window for a hands-free reply after the single ping. The caller has the option of speaking within the 7 seconds or pressing and holding the Call key to speak longer. Holding in the Call key keeps the audio bus switched to the door station’s microphone.
If the 7-second hands-free window ends before the caller presses the Call key to speak, the door station sounds a double ping indicating the audio bus has opened. At this point the caller must press the Call key again to request another session if they wish to speak longer. This also rings the doorbell again.
Door strike release
The optional ISDR1 Door Strike Release module can be activated from any keypad at any time.
When activated, the module stays active for 3 seconds, confirmed by a buzz tone at the keypad and the door station.
On an ISK1 Basic Keypad, the module is activated by pressing and holding the appropriate door key for 3 seconds.
When a communication session is active between a door station and an ISK2 Advanced
Keypad, the module can be activated by pressing and holding both the Previous and Next keys for 3 seconds. If no session is active, the door will first need to be selected on the keypad.
Listen mode
Listen mode is a system state in which one keypad has a constantly active microphone and one or more other keypads are receiving its audio signal. This mode is subject to temporary interruption when the system is used for paging, intercom, or door station sessions.
Selecting a keypad’s own zone connects its microphone to the audio bus 2 seconds after the selection is made. That zone then becomes the sending zone for Listen mode. The keypad’s
Talk key lights up red to indicate the microphone is on. In addition, the zone key on an
ISK1 Basic Keypad blinks red and the display on an ISK2 Advanced Keypad shows MicOn.
If another zone is already selected as a sending zone for Listen mode, the keys on the Basic
Keypad for both the active zone and the desired zone alternately blink red for 7 seconds to indicate which zone’s microphone is active. The
Advanced Keypad alternately displays the active zone and MicOn for 7 seconds.
INSTALLER SECTION
System Functions
Listen mode (cont’d)
Selecting the sending zone on other keypads connects their amplifiers to the audio bus so they can listen to the sending zone.
Listen mode can be used with DND in the same zone as long as Listen mode is enabled first.
On either type of keypad, selecting a zone other than its own disables Listen mode.
Because Listen mode is the lowest priority communication, it can be interrupted by other functions, including an intercom session from the Listen mode sending keypad. When Listen mode is interrupted, the sending and receiving keypads give a system busy indication until the interruption is over.
If the audio bus is not available, attempting to activate a keypad’s microphone for Listen mode will result in a system busy indication.
Do Not Disturb (DND) mode
Placing a zone in Do Not Disturb (DND) mode prevents the audio bus from being switched to the keypad amplifier in that zone. Thus, that zone will not receive any pages, intercom calls, door station calls, or doorbell chimes (unless a separate doorbell is used). However, DND mode will not prevent the zone from receiving audio from a multiroom audio system.
The volume setting in effect when a zone is put in DND mode is retained when DND is disabled.
DND mode can be used in conjunction with
Listen mode as long as Listen mode is selected first. If DND is selected first, pressing any key to enable Listen mode will exit DND mode.
When a zone attempts an intercom session with a zone that is in DND mode, the DND key on the sending keypad blinks red for 7 seconds after the Talk key is pressed. Also, on the ISK1
Basic Keypad, the zone key for the zone in DND mode blinks red.
Audible keypad volume level indication
When the audio bus is inactive, pressing the
Volume Up or Volume Down key on a keypad sounds a ping tone to audibly indicate the keypad’s output level. As volume is increased the ping tone gets louder and vice versa. Once the volume adjustment reaches either end of the range, the ping tone no longer sounds.
Keypad backlight
The keypad backlighting comes on whenever any system function is activated and goes off after 60 seconds of system inactivity.
System busy
If someone attempts to start a page or intercom session when the system is busy, the Talk key on the keypad blinks red for 7 seconds to indicate the system is unavailable. The ISK2
Advanced Keypad display also flashes Busy at the same time.
29
30
INSTALLER SECTION
System test
System function test
Paging
Initiate a page from any keypad
❏
Verify all keypads indicate the sending zone
❏
Verify the page is heard in all zones
❏
Verify double ping in receiving zones when
Talk key is released
❏
Verify 30-second timeout for sending zone indication on receiving keypads
Reply to a page from a receiving zone
❏
Verify communication with sending zone
Intercom
Initiate an intercom session
❏
Verify the receiving zone keypad indicates the sending zone
❏
Verify the message is heard in the receiving zone
❏
Verify single ping in receiving zone when Talk key is released
❏
Verify double ping in receiving zone 7 seconds after Talk key is released
❏
Verify 30-second timeout for sending zone indication on receiving keypads
Reply to initial message
❏
Verify hands-free operation within 7 seconds of single ping
❏
Verify reply is heard in sending zone
Door station call
Initiate a door station call
❏
Verify all keypads indicate the door station
❏
Verify door chime
❏
Verify 15-second timeout for door station indication on keypads
Reply to door station call
❏
Verify reply is heard at door station
❏
Verify single ping at door station when Talk key is released
Answer reply from door station
❏
Verify hands-free operation within 7 seconds of single ping
❏
Verify answer is heard in replying zone
Door strike release
Initiate a door strike release
❏
Verify module activation
❏
Verify audible confirmation
Listen mode
Activate microphone in zone to be heard
❏
Verify keypad confirmation of microphone on
Select zone to be heard at another keypad
❏
Verify keypad indication of selected zone
❏
Verify audio transmission from zone with active microphone
Disable Listen mode
❏
Verify clearing of Listen mode
Do Not Disturb mode
Enable DND mode on a keypad
❏
Verify DND indication on keypad in DND mode
❏
Verify no interruption by paging, intercom, or doorbell
❏
Verify DND indication on another keypad attempting to intercom to keypad in DND mode
Enable DND mode on a keypad
❏
Verify clearing of DND mode
INSTALLER SECTION
Troubleshooting
Troubleshooting chart
Symptom
Talk key flashes rapidly and Advanced
Keypad indicates Wrong Connection shortly after powering system
No response or backlight at any keypad
No response or backlight at one keypad; others work OK
Possible Cause
Keypad connected to door station port or door station connected to keypad port on hub
Door station connected to a hub other than hub 1
Hub ID numbers not assigned
What to Do
Check keypad and door station connections at hub
Check door station connections at hub
No power to hub(s)
Assign a unique ID number for each hub
Make sure a power supply is plugged into each hub and the AC circuit is energized
Check orange pair Open power or ground wire in CAT-5 cable
Faulty RJ-45 connection at hub
Loose CAT-5 connection at keypad
Faulty port on hub
Open status wire in CAT-5 cable
Check modular connector and test
CAT-5 cable
Make sure wires are punched down tightly on keypad connector
Swap modular connector to another port; if keypad works OK, replace hub
Check green wire Hub doesn’t recognize keypad (no zone indication on Advanced Keypad display when powering up)
No communication audio in one zone; speakers play music OK
No doorbell chime
Doorbell chime too loud/soft overall
Doorbell chime too loud/soft in some zones, OK in others
Room speakers not properly connected to keypad
Open audio wire in CAT-5 cable
Chime not selected at hub
Doorbell chime gain not adjusted
Doorbell chime volume set to variable level and keypads set to different volume levels
Make sure speakers are connected to keypad output connector
Check brown pair
Make sure a chime selection is made on hub 1
Adjust doorbell chime gain on hub 1
Set doorbell chime volume switch to fixed level (1)
Adjust keypad volume settings
Check green/white wire Door strike release module doesn’t operate
Assigned zone labels appear on some
Advanced Keypads but not others
Open trigger wire in CAT-5 cable
Multiple hubs not linked together
Hub 1 powered up too early (more than 15 seconds) before other hubs
Link hubs
Cycle power on hub 1
31
REFERENCE SECTION
Specifications
32
Technical Specifications
ISDR1 Door Strike Release Module
CAT-5 connectors: (2) 110 punch-down blocks
Strike release relay: 1-pole double-throw (NC/NO)
Relay connector: Removable 3-pole screw terminal
Relay wire size: Up to 14 AWG (1.63 mm)
Relay contact rating: 5 A @ 12 VDC
Mounting method: Surface
Dimensions: 3” W x 1.875” H x 1” D
(7.6 x 4.8 x 2.5 cm)
Weight: 4.8 oz (136 g)
ISH1 Hub
Keypad ports: (6) 8-pole modular RJ-45
Door station ports: (2) 8-pole modular RJ-45
Link ports: (2) 8-pole modular RJ-45
Firmware update port: 4-pole port for Programming Cable,
Russound part #2500-521065
Switches: 4-switch DIP for hub ID setting
8-switch DIP for 2 doorbell settings
Potentiometer for doorbell volume
Doorbell options: 7 chime patterns plus no chime
Power requirement: 15 VDC 3.5 A (power adapter included)
Mounting method: Surface or structured wiring panel
Dimensions: 6.438” W x 5.125” H x 1.813” D
(16.4 x 13.0 x 4.6 cm)
Weight: 25.6 oz (0.73 kg)
ISK1 Basic Keypad
User controls: 6 zone selection/indication keys
Talk key
2 door selection/indication keys
DND selection/indication key
Volume Up and Volume Down keys
Key backlighting: Installer-selectable amber or green, with red indication
Audio input: Built-in microphone with automatic gain control
Amplifier: Monaural (for system functions only)
Amplifier power: 2 watts
Min. load impedance: 6 ohms per channel
Speaker relay: 4-pole double-throw
Speaker relay rating: 50 watts RMS continuous
Speaker connector: 8-pole screw terminal
Speaker wire size: Up to 14 AWG (1.63 mm)
CAT-5 connector: 110 punch-down block
Power consumption: 15 VDC 800 mA maximum,
200 mA typical
Keypad style: Single-gang Decora ®
Dimensions: 1.875” W x 4.188” H x 2.5” D
(4.8 x 10.6 x 6.4 cm)
Weight: 4.8 oz (136 g)
ISK2 Advanced Keypad
Display: 5-character backlit LCD panel
User controls: Talk key
Next and Previous keys
DND selection/indication key
Volume Up and Volume Down keys
Backlighting: Installer-selectable amber or green, with red indication
Audio input: Built-in microphone with automatic gain control
Amplifier: Monaural (for system functions only)
Amplifier power: 2 watts
Min. load impedance: 6 ohms per channel
Speaker relay: 4-pole double-throw
Speaker relay rating: 50 watts RMS continuous
Speaker connector: 8-pole screw terminal
Speaker wire size: Up to 14 AWG (1.63 mm)
CAT-5 connector: 110 punch-down block
Power consumption: 15 VDC 800 mA maximum,
200 mA typical
Keypad style: Single-gang Decora ®
Dimensions: 1.875” W x 4.188” H x 2.625” D
(4.8 x 10.6 x 6.7 cm)
Weight: 5.6 oz (159 g)
ISK3 Door Station
User control: Call key with amber backlight
Audio input: Built-in microphone with automatic gain control
Amplifier: Monaural (for system functions only)
Amplifier power: 2 watts
Volume control: Installer-adjustable potentiometer
Audio output: Built-in speaker
Cover plate: Weatherproof plated die-cast zinc
CAT-5 connector: 110 punch-down block
Doorbell connector: 2-pole screw terminal
Doorbell wire size: Up to 18 AWG (1.024 mm)
Doorbell contact: 1 A @ 12 VDC
Power consumption: 15 VDC 220 mA maximum
Dimensions: 3” W x 5.125” H x 3.25” D
(7.6 x 13.0 x 8.3 cm)
Dimensions in wall box: 2” W x 2.875” H x 2.75” D
(5.1 x 7.3 x 7.0 cm)
Wall box required: Single-gang, 22 cu in (360 cm 3 ) min
Weight: 8 oz (227 g)
System
Maximum zones: 36 (up to 6 hubs)
Door stations: 2 maximum
Communications cable: CAT-5/CAT-5e
Maximum cable length: 250 feet (76 m)
REFERENCE SECTION
Accessories and Warranty
Accessories
S1-18-R Single-gang plastic wall box with captive mounting nails, 18 cu in (for interior keypads)
S1-18-W Single-gang plastic wall box with Auto Clamps ® , 18 cu in (for interior keypads)
S1-22-R Single-gang plastic wall box with captive mounting nails, 22 cu in (for door stations)
AWCAT5 8-conductor, 24-gauge solid copper CAT-5e cable, 4 twisted pair, 1000 feet (305 m)
AW162CL3 2-conductor, 16-gauge unshielded speaker cable, 1000 feet (305 m)
AW164CL3 4-conductor, 16-gauge unshielded speaker cable, 500 feet (152 m)
ACRP-26 Single-gang Decora ® wall plate, pack of 25 (white, almond, bone, black, or brown)
SWP-1 Single-gang screwless Decora ® wall plate (white or almond)
Warranty
The Russound ComPoint system components (ISH1, ISK1, ISK2, ISK3, and ISDR1) are fully guaranteed for two (2) years from the date of purchase against all defects in materials and workmanship. For this warranty to apply, the components must be installed and used according to their written instructions. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. Accidental damage and shipping damage are not considered defects under the terms of this warranty. Russound assumes no responsibility for defects resulting from abuse or servicing performed by an agency or person not specifically authorized in writing by Russound. If service is necessary, it must be performed by Russound. Damage to or destruction of components due to excessive power voids the warranty. In these cases, the repair will be made at the owner’s expense. To return a product for repairs, the unit must be shipped to Russound at the owner’s expense, along with a note explaining the nature of the service required. Be sure to pack in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at 603.659.5170 for a Return Authorization number. Write the RA number on the shipping label and ship to: Russound, 5 Forbes Road, Newmarket NH 03857.
Russound sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void the warranty on the applicable product.
33
34
NOTES
NOTES
35
ComPoint
The music lover’s intercom solution
Instruction Manual
Models
ISH1
ISK1
ISK2
ISK3
ISDR1
Russound
5 Forbes Road, Newmarket NH 03857 USA
Tel 603.659.5170 • Fax 603.659.5388
www.russound.com
Technical Support: [email protected]
28-1211 03/30/06
Copyright © 2006 Russound. All rights reserved. All trademarks are the property of their respective owners. Specifications are subject to change without notice. Russound is not responsible for typographical errors or omissions.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement