Battery installation and charging
Quick start guide
for model LS5145
Install the battery as shown below. For optimal
performance, charge the handset battery for at least
16 hours before use.
1. Press the tab and
slide the battery
compartment cover
downwards.
Install the telephone base
2. Insert the plug as
indicated. Make sure
it is plugged securely
and matches the colorcoded label inside the
battery compartment.
Install the telephone base as shown below.
To pair and connect your first Bluetooth cell
phone:
To pair and connect your first Bluetooth headset:
1. P r e s s C E L L o n t h e
telephone base.
1. Press the MENU softkey on
the telephone base.
THIS SIDE UP
Battery Pack
BT5632 / BT5872
3.6V 550mAh Ni-MH
THIS SIDE UP
Battery Pack
BT5632 / BT5872
3.6V 550mAh Ni-MH
WARNING: DO NOT BURN OR PUNCTURE BATTERIES
MADE IN CHINA
Telephone
line cord
WARNING: DO NOT BURN OR PUNCTURE BATTERIES
MADE IN CHINA
Telephone wall jack
Power adapter
Pairing your first Bluetooth headset
2. Press the YES softkey.
DSL filter (not included)
for DSL users
Electrical outlet
not controlled by
a wall switch
Pairing your first Bluetooth cell phone
3. Place the battery
4. Align the cover flat
with the label against the battery
THIS SIDE UP facing compartment, then
up and the wires
slide it upwards until it
inside the battery
clicks into place.
compartment.
Cellular operation
requires Bluetooth
connection.
Set up Cellular?
YES
3. Set your cell phone to search
for or add new devices, then
press the NEXT softkey.
NO
Set up Cellular
Set your Cellular to
search for devices,
then press NEXT
next
4. Once your cell phone finds
your VTech LS5145, select
it and then enter the PIN
0000 on your cell phone.
Set up Cellular
VTech LS5145
in Discoverable Mode
PIN=0000
STOP
HELP
THIS SIDE UP
Battery Pack
BT5632 / BT5872
3.6V 550mAh Ni-MH
WARNING: DO NOT BURN OR PUNCTURE BATTERIES
MADE IN CHINA
THIS SIDE UP
Battery Pack
BT5632 / BT5872
3.6V 550mAh Ni-MH
WARNING: DO NOT BURN OR PUNCTURE BATTERIES
MADE IN CHINA
Set up Cellular
Pairing complete
Connect to
Cellular ?
YES
NO
Telephone base
NOTES:
1. Use only the power adapter and battery
supplied with your VTech telephone.
2. For complete feature instructions, please refer
to your user’s manual.
Main Menu
Voice Mail
Intercom
Bluetooth
3. Press the UP and DOWN
NavKeys to highlight Set
up Headset, then press the
SELECT softkey.
Bluetooth
Set up Cellular
Set up Headset
Active Devices
4. S e t y o u r h e a d s e t i n
discoverable mode, then
press the NEXT softkey.
Select
Select
Set up Headset
Set your Headset in
Discoverable mode,
then press NEXT
next
5. W h e n t h e p a i r i n g i s
completed, press the YES
softkey on the telephone
base.
5. Charge the
handset by placing
it in the telephone
base. The handset
charge light on the
handset will be on
when charging.
2. Press the UP and DOWN
NavKeys to highlight
Bluetooth, then press the
SELECT softkey.
Cellular setup
completed
5. Once the telephone base
finds your headset, select
it and then press the PAIR
softkey.
6. Enter your headset’s PIN
on the telephone base, then
press the DONE softkey.
The default PIN for most
headsets is 0000.
7. W h e n t h e p a i r i n g i s
completed, press the YES
softkey on the telephone
base.
Headsets Found
Mary’s Headset
find
pair
info
Set up Headset
Enter PIN:
0000
done
help
erase
Set up Headset
Pairing complete
Connect to
Headset ?
YES
NO
Headset setup
completed
Charge light
Making, receiving and ending
calls
Using your answering system
More about Bluetooth
IMPORTANT!
To play answering system messages:
To make a HOME call:
Using a handset
• Dial the telephone number, then press HOME/
FLASH or
on the handset, or HOME on the
telephone base.
To receive a HOME call:
• Press HOME/FLASH or
on the handset or
HOME on the telephone base.
1. Press MENU/SELECT when the
handset is in idle mode.
2. Press the UP and DOWN NavKeys
to select Messages, then press
MEN U/ SELECT to enter the
Messages menu.
3. While in the Messages menu:
• Press the PLAY softkey to play
messages.
• Press the RIGHT NavKey to skip to the
next message.
• Press the LEFT NavKey to repeat the
message currently playing. Press twice to
listen to the previous message.
• Press the STOP softkey to stop the
playback.
• Press the DELETE softkey to delete the
message currently being played.
You can make and receive calls using the
HOME and CELL lines. The HOME line is your
conventional telephone land line. The CELL line is
the communications service provided through your
Bluetooth enabled cell phone.
Before using your Bluetooth device(s) with the
telephone base, make sure that:
• Your cell phone and/or headset devices are not
connected to any other Bluetooth device(s) and
the Bluetooth wireless function is on.
• Your device is connected to the telephone base
and on the Active Devices list.
If your product is not working properly:
• Refer to the Troubleshooting section of the
user’s manual.
• Visit our website at www.vtechphones.com or
call 1 (800) 595-9511. In Canada, go to www.
vtechcanada.com or 1 (800) 267-7377.
If you have a Bluetooth headset connected, press
the call button on your headset to receive HOME
calls.
To make a CELL call:
• Dial the telephone number, then press CELL on
the handset or telephone base.
To receive a CELL call:
• Press CELL or
on the handset or CELL on the
telephone base.
To end a HOME or CELL call on the handset:
• Press the OFF/CANCEL or return the handset in
the telephone base or charger.
To end a call on the telephone base:
• Press HOME for a HOME call.
• Press CELL for a CELL call.
Using the telephone base
The BLUETOOTH® word mark and logos are owned by
Bluetooth SIG, Inc. and any use of such marks by VTech
Holdings Limited is under license. VTech Holdings Limited is
a member of Bluetooth SIG, Inc. Other trademarks and trade
names are those of their respective owners.
If you experience difficulty using your Bluetooth
cell phone:
1. Make sure that your Bluetooth cell phone is
working properly. See your Bluetooth device(s)
user’s manual for more information.
2. Delete the VTech LS5145 device on your cell
phone, then delete your cell phone on the Pair
Devices list.
3. Repeat the pairing process in Pair your first
Bluetooth cell phone in this Quick start guide.
When you have a message on
the telephone base:
• Press PLAY/SKIP to
play messages.
• Press PLAY/SKIP
again to skip to the
next message.
• Press REPEAT to
repeat the message
currently playing.
Press REPEAT twice to listen to the
previous message.
• Press the STOP softkey to stop the
playback.
• Press the DELETE softkey to delete the
message currently being played.
96-006511-010-100
issue 0