Miele ESS 2060 Operating instructions

Operating
instructions
Coffee System
CVA 2660
To prevent accidents
and machine damage
read these instructions
before
installation or use,
M-Nr, 06 541 300
Contents
Contents
iMPORTANT
SAFETY iNSTRUCTiONS
When using electricaJ appliances,
followed, including the following:
basic safety precautions
shouJd ah_ays be
Read alt instructions before installation or use of the coffee system.
Be certain your appliance
is
proper,y
insta,,ed
and
grounded
by
than intended use. Any other use
could be dangerous.
i nly. Do not use appliance for other
This appliance complies with current
the appliance can cause personal
i injury
afety and
requirements.
material damage.
Improper use of
a qualified technician. To guarantee the
electrica! safety of this appliance,
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the house checked by a qualified
electrician. The manufacturer cannot be
held responsible for damages caused
by the lack or inadequacy of an
effective grounding system.
Do not use an extension cord to
i [esponsible
The manufacturer
cannotcaused
be heldby
for damage
connect
theapp,,ance
toe,ectr,cit
Extension cords do not guarantee the
required safety of the appliance
(danger of overheating).
E_ectrica_ safety
Before connecting the appliance to
the electrical supply make sure
that the voltage and frequency details
listed on the data plate correspond with
the household electrical supply. If in
doubt, consult a qualified technician.
The appliance must be properly
ii_
installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
installation in these applications. Please
contact the Miele Technical Service
Department with specific requirements.
_nstaHed
before
operation
toensure
that no electrical components are
accessible. Ensure that power is not
supplied to the appliance while
installation work, repairs or
maintenance is performed.
This appliance is not designed for
maritime use or for use in mobile
Before service or maintenance
disconnect
thepower
supply
by
either removing the fuse, "tripping" the
circuit breaker or unplugging the unit.
iMPORTANT
SAFETY iNSTRUCTiONS
Use
,,,,,,',,,,,,ii,i,
Insta,,ation
work
and
repairs
shou,d
only be performed by a trained
technician in accordance with national
and local safety regulations. Repairs
and other work by unauthorized
persons could be dangerous.
Never open the outer casing of the
appliance.
Tampering
with
electrical connections or components
and mechanical parts is dangerous and
may cause machine damage.
If the machine is insta!led in
Use only Nespresso-coffee
capsules with this machine.
The coffee system must be
maintained daily to prevent the
growth of harmful bacteria and
mold. Please read the "Coffee
system care" section of this booklet.
..................................................
:i Caution! There is a risk of burns
when
dispensing
hotbeverages,
ombinat,on
w,th
other
app,,ances,
ty
:e
!:......................
it should be installed with a protective
base between the appliance and the
unit.
To protect against fire, electric
shook
and
,n_ury
topersons
donot
immerse cord or plugs in water or other
liquid.
Do
cord
hang
over
edge
of
tablenot
or,et
counter,
or touch
hot
surfaces.
Do not operate any appliance with
a damaged cord or plug or after
the appliance malfunctions, or has
been damaged in any manner. Contact
Miele.
Always attach the cord to the
appliance first, then plug it into the
wall outlet. To disconnect, turn the
machine off by pressing the left iog
shuttle, then remove plug from wall
outlet.
ii
iiliiiiiiiiii!i
Do
nottouch
hot
surfaces,
Use
_og
shuttles
or steam
lever.
Children should not use the
appliance unsupervised.
Danger of scalding!
This appliance must not be
installed or operated outdoors.
To
avo,d
,n_ur,es
a,,ow
thecoffee
system to cool before cleaning or
before putting on or taking off parts.
Turn the machine off at the main switch
when not in use and before cleaning.
Only fill the water tank with cold,
fresh
tapwater.
Warm
orhotwater
or any other liquids may damage the
machine. The water should be changed
daily to prevent bacteria or mold
growth.
iMPORTANT
SAFETY iNSTRUCTiONS
The
water
lines
must
be
rinsed
and
the machine
cleaned
thoroughly
before the first coffee is prepared. See
"Daily coffee system care".
The
use
ofaccessories
not
recommended by the appliance
manufacturer may result in fire, electric
shock or iniury to persons.
Do not reach into the perforator.
Iniuries may occur_
Donot
use
damaged,
broken
or
::}}i:
dented capsules! They may jam in
the machine and damage it.
The
hotwater
and
steam
dispensed could cause scalding!
Use these functions carefully. The
machine must never be used to clean
objects.
Never use a steam cleaner to clean
the appliance. Pressurized steam
could damage electrica! components
and cause a short circuit.
iiliiiiii_i_iliii
The
coffee
system
must
be
descaled
regularly
with the
supplied descaling tablets. In areas
with very hard water the machine needs
to be descaled more often. The
manufacturer cannot be held
responsible for damages resulting from
insufficient descaling.
Only use the descaling tablets
provided
byMiele
and
besure
to
use the correct mixture of water and
descaler. Otherwise appliance damage
may occur.
The
more or
less capsule
dependingplate
onwill
the soil
coffee
capsule used. Clean the capsule plate
as necessary with a cleaning tablet,
available from Miele.
Do not hang, lean, sit or place
heavy
,tems
onthedoor,
The
machine may be damaged.
SAVE THESE
Guide to the machine
Front view
'_ Left display
,'@Right display
,'3 Left iog shuttle
{:sDUpper door handle
(for installation at countertop height)
Press this jog shuttle to turn the
machine on and off,
Turning it selects a desired
program, option or setting,
'_@Right jog shuttle
Press this jog shuttle:
- to start and stop the dispensing
of coffee or hot water,
,'_ Lower door handle
(for installation at a higher level,
e,g, upper cabinets)
,'_ Plastic drip grill
'_©Metal drip catch
_ Coffee dispenser
@ Inset for Cappuccinatore
,t3 Valve / Lever for steam and hot water
- to select an option to alter or
customize a program,
- to save a setting into memory
when the machine is turned off,
Turning it selects a desired
program, option or a setting,
Guide to the machine
mnterior view
®
'J_ Main switch
_ Capsule carousel
_ Capsule plate
(replaced with the descaling funnel
when descaling is performed)
@ Carousel tray
_ Perforator
(not visible, penetrates capsule to
assist in the brewing process)
t_ Water tank
@ Drip tray with grid
(grid avoids spilling during transport)
_ Waste container
Displays
Left display
Right display
-
-
selects coffee or espresso
-
shows current actions, e.g. heating
-
prompts an action, e.g. close the
door
Drink selection
Up to 5 d fferent coffee types ,.L.,,as
well as, steam _;..'._"
and hot water
-
User profiJe
Up to 4 different users
-
lmportantmaintenance
Rinsing ..::"i'::..,
descaling
-
Selection
of Settings
Individual settings and information can
be selected in the right hand display.
Language
-_-
Time
I![I_
Allocation of coffee type
User name
Programming
i
Total number of cups of coffee
dispensed to date
:_t
Maintenance
J:_
Reset to default settings
ii The selected option will be
10
_:
First steps to use
Turning
the machine
on and off
Turning
on
[] Press the left jog shuttle,
When turned on for the first time, a
welcome screen along with other
messages will appear in the right
display. The welcome screen will be
displayed each time the machine is
turned on until 5 drinks (including
steam) have been prepared.
The displays lighL
Turning
off
[] Press the left jog shuttle until the
displays go dark.
when turned off. Jf coffee was
dispensed, the machine will be
rinsed and "Machine Rinsing" will
appear in the right display. When
finished the machine will shut off
completely.
11
First steps to use
Before using the coffee
for the first time
system
4. Rinse the lines
t. CJean the parts
[] Hand wash the coffee capsule plate
with hot water and liquid dish soap.
[] The water tank can be washed in the
dishwasher.
Water runs from the coffee dispenser.
Water runs from the steam valve.
[] Open the appliance door.
[] Lift the water tank and pull it out.
[] Fill the container with fresh, cold tap
water to the "Max." mark. Push the
water tank back into the machine.
3. Fill the system with water
[] Set a cup under the steam valve.
[] Turn the left jog shuttle to "Hot water".
[] Press the right iog shuttle.
hot water.
[] Press the right iog shuttle again to
turn the hot water off.
[] Press the steam lever down.
[] Push the steam lever up when steam
starts to be dispensed.
The lines are filled and the coffee
system is ready to use.
12
[] Press the right iog shuttle.
[] Press the steam lever down.
2. Fill the water tank
The steam valve dispenses
[] Turn the left iog shuttle to "Rinse".
[] Push the steam lever up after a few
seconds.
Filling
water and coffee
capsules
FHHng the water tank
The water tank should be washed and
filled with fresh cold tap water before
each day of use.
liquid except cold water into the
i water
ever tank.
put hot water or any other
[] Open the appliance door.
[] Lift the water tank and pull it ouL
[] Fill the container with fresh, cold tap
water to the "Max/' mark.
A valve at the tank front prevents leaks.
[] Push the water tank back into the
machine.
13
Filling
water and coffee
Filling the coffee
carousem
capsules
capsule
There are five chambers, each can hold
four capsules. The coffee types have to
be allocated to their respective
chambers to get the desired coffee
type. You can also fill each chamber
with the same coffee type.
The chambers are factory set for a
coffee type. Fill the chambers
respectively or program other coffee
types according to your preference.
See "Allocating various coffee types".
[] Pull the carousel tray, '_, all the way
out.
[] Take the carousel, _@,out.
[] Insert the capsules into the
chambers, @, with the flat, silver side
down.
loosely in the chambers so they do
i Take care that the capsules sit
not jam.
[] Insert the carousel into the carousel
tray.
[] Push the carousel all the way into the
machine.
[] Close the door.
The machine aligns the carousel
automatically. A sound will be heard.
Changing
the coffee
capsuJes
[] Pull out the carousel tray and lift out
the carousel.
[] Push the carousel ring, ._,""up and
take out the capsules.
14
AHocating
Twelve different Nespresso coffee types
are available for this coffee system,
They differentiate in terms of acidity,
fruitness, bitterness and roasL
Therefore the preparing times will vary,
various
coffee types
[] Take the carousel from the machine
to see which coffee type is filled in
each chamber,
See "The Espresso / Lungo range" for
more information on the coffee types,
AJJocating
the coffee
types
[] Turn the right jog shuttle to the
desired chamber and press to
confirm,
Five different coffee types can be filled
in the five chambers of the capsule
carousel, The chambers can be either
allocated to the desired coffee types or
filled with the same coffee type in all
chambers,
[] Turn the left jog shuttle to "Settings",
[] Turn the right jog shuttle to the
"Coffee bean" symbol, Press to
confirm,
The upper line shows the coffee type,
the lower line shows the chamber
number, If no type is allocated to the
chamber, the upper display line shows:
empty
Some coffee types are factory set,
which you can either accept or change,
15
AHocating
AHocating
types
various
different
coffee types
coffee
[] Turn the right jog shuttle to the first
letter or number and press to
confirm. The selected letter shows in
the upper line.
[] Turn the right jog shuttle to the
desired coffee type and press to
confirm it to that chamber.
Setting
a new coffee
To enter text
type
[] Repeat until the desired name is
entered.
To delete text
[] If you made a mistake, turn the right
jog shuttle until "delete" appears in
the display.
[] Pressing it deletes the last letter
entered.
[] Turn the right jog shuttle to "save as"
if no coffee type is allocated yet, to
save a new coffee type or to name a
coffee type yourselfi
[] Turn the right jog shuttle
counterclockwise to the alphabet and
continue entering the name.
[] Press the right iog shuttle.
Saving an entry
The alphabet is displayed. Turn the
right iog shuttle to the right to display
the rest of the alphabet and the
numbers 0 through 9.
[] When the entry is complete, turn the
right iog shuttle until "OK" is
displayed.
[] Press to confirm.
The main menu is displayed, the last
selected chamber is highlighted.
[] To leave the menu turn the rig_ iog
shuttle to the "back" symbol '@" and
press to confirm.
Not saving an entry
[] If you do not want to save an entry
turn the right iog shuttle until "back" is
displayed. Press and the entry will
not be saved.
16
Making
preparing the first drink of the day. If
the "Automatic rinsing" option is set
to "on" and the machine is still cold
this will take place automatically. The
heating system will heat and the
i water
inse lines
the water
will be
lines
rinsed.
before
If the "Automatic rinsing" option is
i
the left display to rinse the lines.
et to "off", use the option "Rinse" in
See "Daily coffee system care".
coffee
If the "Automatic rinsing" option is set to
"on" (default setting) the next message
shows:
Water will run out of the coffee
dispenser and a sound will be heard as
the carousel aligns.
The right display shows:
[] Press the left jog shuttle to turn the
machine on.
The left display lights.
The right display shows briefly:
This is a reminder to fill the water tank
with fresh water.
The next message shows:
17
Making
coffee
Prewarrning
the cups
To prewarm with hot water
Prewarming the cups allows the coffee
to fully develop the flavor and aroma,
are very hot.
[] Place a cup under the steam / hot
water valve,
[] Turn the left iog shuttle to the "Hot
water" option,
[] Press the right iog shuttle and half fill
the cup with hot water,
[] Press the right iog shuttle again to
stop the water from dispensing,
[] Leave the cup for a few seconds to
warm, then pour the water away,
To prewarm with steam
[] Turn the left iog shuttle to the
"Heating with steam" option,
[] Press down the steam lever.
,H
i The steam supply is temporary, If the_ !
ii steam stops prematurely push the
w
...........
[] Push the lever up to stop the steam
from dispensing,
[] Pour away any excess water.
18
Making
Espresso
and coffee
The flavor of the coffee depends on the
coffee capsule and the quantity of
water used. To ensure the machine
uses exactly the amount of water to suit
your taste and your cup size, there is a
choice of four serving sizes for
espresso / coffee.
mnterrupting
coffee
the brewing
[] Press the right iog shuttle to interrupt
the coffee dispensing immediately.
For coffee / espresso recipes see
Aside from the serving size, making
coffee and espresso are done the same
way.
[] Place a cup under the coffee
dispenser.
[] Turn the left jog shuttle to the desired
coffee type.
[] Turn the right jog shuttle to the
desired coffee or espresso size.
Espresso
Coffee
(_
Double espresso
[_
Double coffee
When selecting a double coffee or
espresso, two capsules will be
dispensed one after another. You can
set the water amount to your taste. See
"Setting the serving sizes".
[] Press the right iog shuttle to confirm
and the drink will be dispensed.
19
Making
coffee
Cappuccinatore
(milk froth mug)
A cappuccinatore (milk froth mug) is
supplied with the appliance,
Before using the cappuccinatore for
the first time, wash it either in the
dishwasher or with hot water and
liquid dish soap,
See "Common coffee system care"•
The cappuccinatore has a valve, _,
over the handle and a spout on its side,
The steam is regulated by turning the
valve:
t Hot milk is prepared
2 Froth is prepared
[] Turn the spout so that the black dot
points to the respective symbol,
Milk is frothed
higher
fat content,
the
i froth,
Cold, The
whole
milk the
is best
for creating
better the froth•
t into the cup
2 into the cappucc_natore
cappuccinatore the froth is hotter
and has more volume,
When frothing milk into a cup while
dispensing a coffee, the steam
system must be turned on, See
"Settings - Steam system",
2O
Making
Frothing
coffee
milk into the cup
[] Prewarm the cup before filling with
froth,
[] Fill the cappuccinatore to the upper
"max" mark with cold milk,
[] Turn the spout to the cup symbol,
[] Turn the valve over the handle to the
froth symbol,
[] Place the cappuccinatore
steam valve,
under the
[] Place a cup underneath the spout of
the cappuccinatore,
[] Press the steam lever, _, down and
"connect" the valve with the
cappuccinatore,
'_2_.
Milk is frothed by the hot steam and
dispensed into the cup,
[] Turn the cappuccinatore valve to the
right, Once the froth flows steadily,
turn it to the lefL
[] Push the steam lever up when
enough froth is prepared,
21
Making
Frothing
coffee
miJk in the cappuccinatore
[] Fill the cappuccinatore to the lower
"max" mark with cold milk.
[] Turn the spout to the cappuccinatore
symbol.
Rinsing
the lid
For a quick cleaning between froths the
cappuccinatore lid can be rinsed with
the steam valve.
[] Turn the valve over the handle to the
froth symbol
[] Turn the spout to the cup symbol.
[] Place the cappuccinatore
steam valve.
[] Turn the left jog shuttle to "Heating
with steam".
[] Place the cappuccinatore
steam valve,
under the
[] Place a cup under the
cappuccinatore spout.
under the
[] Turn the left iog shuttle to "Rinse",
[] Press the steam lever down,
The right display shows:
[] Press the steam lever, Jj'-',down to
connect the valve with the
cappuccinatore, ,'_,
The process will stop automatically
when the lid is rinsed,
After
The milk will be frothed in the
cappuccinatore.
use
At the end of each day, the lines of the
coffee system should be rinsed,
See "Daily coffee system care",
[] Push the steam lever up when the
milk is frothed to the desired degree,
22
Dispensing
hot water
Hot water
[] Place a cup under the hot water /
steam valve,
[] Turn the left jog shuttle to "Hot water",
[] Press the right jog shuttle to confirm,
[] Press again to stop the water from
dispensing,
23
Setting
serving
sizes
The flavor of the coffee depends on the
coffee type and the quantity of water
used. To ensure the machine uses
exactly the amount of water to suit your
taste and your cup size, there is a
choice of two serving sizes for
espresso / coffee.
The espresso symbol dispenses a
standard size espresso.
The espresso water amount can be set
between 1 and 2.5 oz (30 and 75 ml).
The coffee symbol dispenses coffee
for a standard size coffee cup. It uses
the same quantity of coffee as an
espresso, but adds more water. The
water amount can be set between
1 and 6 oz (30 and !75 ml).
The double espresso [_ and doubJe
coffee _ symbols dispense two
portions of espresso or coffee one after
another. This requires two coffee
capsules and double the amount of
water set for a single coffee or
espresso..
Setting
a default
serving
size
Have the correct cups handy.
[] Place the desired cup under the
coffee dispenser.
[] Turn the left jog shuttle to the desired
coffee type.
[] Select the drink you would like to
program.
PROSRRH
THEB'IOUHT
[] Press and hold the right jog shuttle
until "Program the amount" shows in
the display.
[] Release the jog shuttle.
[] Press the right jog shuttle again when
the cup is filled to the desired
preference.
The programmed amount will now be
dispensed every time the drink is
selected.
water amount
i The
maximum
will then
be saved
for the drink selected.
24
Setting
Setting
the user name
Up to four different user profiles can be
programmed to accommodate different
preferences and serving sizes. See
"Setting serving sizes".
user profiles
To enter text
[] Turn the right jog shuttle to the first
letter or number and press to
confirm. The selected letter shows in
the upper line.
[] Repeat until the desired name is
entered.
To delete text
[] Turn the left jog shuttle to "Settings".
[] Turn the right jog shuttle until "delete"
appears in the display.
[] Pressing the jog shuttle deletes the
last letter entered.
[] Turn the right jog shuttle to the "User
name" symbol, then press to confirm
the selection.
[] Turn the iog shuttle counterclockwise
to the alphabet and continue entering
the name.
Saving an entry
[] Turn the right jog shuttle to the
desired user and press to enter a
user name.
The alphabet is displayed. When
turning the iog shuttle to the right, the
rest of the alphabet and the numbers 0
through 9 are shown.
[] When the entry is complete, turn the
jog shuttle until "OK" is displayed.
Press to confirm.
The display shows th_ main menu.
The "back" symbol '_'" is selected.
[] Press the right iog shuttle to get to
the main display menu.
Not saving an entry
[] Turn the right jog shuttle until "back"
is displayed.
[] Press the jog shuttle and the entry
will not be saved.
25
Setting
user profiles
Setting user profiles
(serving
sizes)
In addition to the default, different
serving sizes can be programmed
four additional users.
Making espresso
user profile
for
/ coffee
with
If a user profile was set, select the
profile first before preparing a drink.
[] Turn the left iog shuttle to "Profile".
[] Turn the left jog shuttle to "Profile".
[] Turn the right jog shuttle until the
desired user name is selected. Press
to confirm.
The } symbol will appear in the upper
right hand corner of the left display to
show that a user profile has been
selected.
[] With the right jog shuttle select the
user. Press to confirm.
The user symbol } will be shown in the
upper right hand corner of the left
display to signify that a user was
selected.
[] Place a cup under the coffee
dispenser.
[] Proceed as if setting a default
serving size. All water quantities will
now apply for the selected user.
[] Turn the left jog shuttle to the desired
coffee type.
[] Turn the right jog shuttle to the
desired coffee / espresso size.
[] Press to confirm and the drink will be
dispensed.
26
Settings
The coffee system can be customized
to suit individual preferences.
Selecting
a manguage
[] Turn the left iog shuttle to "Settings".
The language symbol is selected in the
right display.
[] Press the right iog shuttle to select
the language option.
[] Turn the right jog shuttle until the
desired language shows in the
display.
A check marks the selected language.
SeJectabJe Janguages: English US and
GB, German, French, Dutch, Italian,
Spanish, Portuguese, Turkish, Swedish,
Norwegian, Danish, Finnish, Polish,
Czech, Hungarian, Greek and Russian.
[] Press the right iog shuttle to select
the language option.
The setting will be automatically saved
and the display will go back to the
previous screen.
All displays will now appear in the
selected language.
Ifa language is accidentally
ii selected, follow the flag to return to
gt
.......................
27
Settings
Setting
the time
of day
[] Turn the left jog shuttle to "Settings".
[] Turn the right jog shuttle to select the
hours, press to confirm.
The language symbol is highlighted in
the right display.
[] Turn the right jog shuttle to select the
minutes, press to confirm.
[] Turn the right jog shuttle to the clock
symbol, press to confirm.
The setting will be automatically saved
and the display will go back to the
previous screen_ -P,
Ho symbols for
preset times now be will shown.
[] Press the right jog shuttle again.
[] Turn the right jog shuttle to select the
time format, press to confirm.
28
Settings
Turning
off after Standby
time
To conserve energy the coffee system
can be set to turn off automatically after
a programmed time interval.
A time period between 20 minutes and
2 hours can be selected. The time is
measured from the last time coffee /
espresso was dispensed.
The setting will be automatically saved
and the display will go back to the
previous screen. The coffee system will
turn off at the preset time.
If rinsing is set to "on" and the
machine has been used, the coffee
system will automatically rinse the
tines before turning off.
[] Turn the left jog shuttle to "Settings".
[] Turn the right jog shuttle to the clock
symbol, press to confirm.
[] Turn the right jog shuttle to "SWITCH
OFF AFTER". Press to confirm the
setting.
[] Turn the right jog shuttle until the
desired turn off time is set, press to
confirm.
29
Settings
Turning
on at a preset
time
A specific time can be set to turn the
machine on, e.g. for breakfast. In order
to use this function the clock has to be
set.
The setting will be automatically saved
and the display will go back to the
previous screen. The coffee system will
turn on at the preset time.
If rinsing is set to "on", the coffee
system will automatically rinse the
tines when turned on.
[] Turn the left jog shuttle to "Settings".
[] Turn the right jog shuttle to the clock
symbol, press to confirm.
that the machine does not turn on
i again. This is a safety measure so
[] Turn the right jog shuttle to "Switch on
at" (this will only be seen if the clock
is correctly set).
[] Press the jog shuttle to confirm the
setting.
[] Turn the right jog shuttle to set the
hours, press to confirm.
[] Turn the right jog shuttle to set the
minutes, press to confirm.
3O
Settings
Turning
off at a preset
time
A specific time can be set to turn the
coffee system off, In order to use this
function the clock has to be set,
The setting will be automatically saved
and the display will go back to the
previous screen, The coffee system will
turn off at the preset time,
If rinsing is set to "on" and the
machine has been used, the coffee
system will automatically rinse the
tines before turning off.
[] Turn the left jog shuttle to "Settings",
Deleting
[] Turn the right jog shuttle to the clock
symbol, press to confirm,
the preset
times
[] Repeat the steps to set the preset
time until you are prompted to set the
actual time of day,
[] Turn the iog shuttle until only dashes
are shown in the second line of the
display,
[] Turn the right jog shuttle to "Switch off
at" (this will only be seen if the clock
is correctly set), Press to confirm the
setting,
[] Press the right iog shuttle to confirm,
[] Turn the right jog shuttle to set the
hours, press to confirm,
[] Turn the right jog shuttle to set the
minutes, press to confirm,
31
Settings
Setting Hghting, dispmay
contrast
and brightness
[] Turning the right jog shuttle clockwise
increases the bar size and brightens
the settings,
[] Press the right iog shuttle to save the
settings,
[] Turn the left jog shuttle to "Settings",
The display shows th_ previous screen,
The "back" symbol '@": is selected,
[] Press the right iog shuttle to display
the main menu,
[] Turn the right jog shuttle to the
"Programming" symbol, press to
confirm,
[] Turn the right jog shuttle to the
desired option:
Lighting -_?, Display contrast ,',i_,
Display brightness ai::_:i',
[] Press to confirm,
A bar shows in the display,
[] Turning the right jog shuttle
counterclockwise, reducing the bar
size, will decrease the lighting,
display contrast and brightness,
32
Settings
Automatic
rinsing
The rinsing feature flushes out coffee
residue and pre-warms the coffee
system. When "Automatic rinsing - on"
is selected the system will automatically
be rinsed when the appliance is turned
on or off. "Heating - up please wait" is
shown in the display. If this feature is
set to "Automatic rinsing - off" the
system will only be flushed and
pre-warmed when selected manually.
[] Place an empty cup under the coffee
dispenser.
[] Turn the right jog shuttle to select "on"
or "off", press to confirm.
A check marks the current setting.
The display now shows the _in
screen. The "back" symbol '@" is
selected.
[] Press the right iog shuttle to return to
the main display menu.
[] Turn the left jog shuttle to "Settings".
[] Turn the right jog shuttle to the
"Programming" symbol, press to
confirm.
[] Turn the right jog shuttle to the
"Automatic rinsing" option.
Press to confirm.
33
Settings
Steam
system
To conserve energy, the steam system
can be turned off if steam is not used
all the time.
[] Turn the right jog shuttle to select "on"
or "off".
A check marks the current setting.
[] Press the right iog shuttle to save the
settings.
The display now shows the pr.evious
screen. The "back" symbol '@" is
selected.
[] Turn the left jog shuttle to "Settings".
[] Turn the right jog shuttle to the
"Programming" symbol, press to
confirm.
[] Turn the right jog shuttle to the
"Steam system" option. Press to
confirm.
34
[] Press the right jog shuttle to return to
the main display menu.
Settings
Total coffee
counter
(mNFO)
If the option "lnfo" is selected, the
display will show the number of cups of
coffee dispensed to date (espresso,
coffee, double espresso / coffee).
Factory
setting
This option allows you to reset all saved
settings to the factory default.
[] Turn the left iog shuttle to "Settings".
[] Turn the left jog shuttle to "Settings".
[] Turn the right jog shuttle to the
"Factory default" symbol.
[] Turn the right jog shuttle to the "lnfo"
symbol, press to confirm.
[] Press to confirm.
The number of coffees already
dispensed will appear in the display.
[] Press the right iog shuttle to return to
the main screen of the display.
[] Turn the right jog shuttle to select
"reset".
[] Select "back" to go back to the
previous screen without changing the
settings in the memory.
[] Press to confirm.
35
System
lock
The coffee system can be locked so
that it cannot be used by children or
those not familiar with the operating
instructions,
Locking the coffee system
[] Turn the coffee system off by
pressing the left jog shuttle,
[] Turn the right jog shuttle until the
display shows "System lock",
[] Press to confirm,
[] Turn the jog shuttle to "on" and press
to activate the system lock,
The appliance is now locked and will
not operate. The system will remain
locked and the lighting will remain
turned off even if the jog shuttles are
turned,
When the jog shuttles are pressed or
turned the display shows:
UnJocking the coffee system
[] Follovv the steps for "Locking the
coffee system" but select "off" to
deactivate the system lock,
The appliance is now unlocked and
ready for use,
36
Daity coffee
system
care
The following components of the coffee
system should be cleaned after each
day of use to prevent mold and
bacteria growth.
Dishwasher
safe
- Water tank
Rinse
If you do not wish to rinse the lines
automatically, they have to be flushed
manually. It is recommended that the
machine is rinsed twice daily, once
before using the machine and once
before turning it off for the day.
-
Drip tray with grid
-
Metal drip catch
-
Cappuccinatore
(if used)
Hand wash only with hot water and
Hquid dish soap
-
Plastic drip catch
[] Place a cup under the coffee
dispenser and the steam valve.
[] Turn the left jog shuttle to "Rinse".
[] Press the right jog shuttle.
Water runs from the coffee dispenser.
[] Press the steam lever down.
Water runs from the steam valve.
[] Push the steam lever up after a few
seconds.
The lines are rinsed. Drinks can either
be prepared now or the machine may
be turned off.
37
Common
coffee
system
care
mnterior
Drip tray
[] Clean all interior parts and areas of
the machine with a solution of hot
[] Clean and dry the metal contacts at
the back of the drip tray. If the
contacts are soiled or wet the unit
cannot read when the drip tray is full
and needs to be emptied.
water and liquid dish soap. See
below for more details.
CapsuJe carousel
and tray
[] Pull out and remove. Both pieces are
dishwasher safe.
Capsule carousel
niche
[] Push the drip tray, with the grid
inserted, along the right hand side of
the opening and to the back of the
machine. Close the door.
[] Clean the sensor in the carousel tray
niche. Dry with a soft cloth. The
carousel chambers are read by the
sensor.
Waste container
Coffee dispenser
cover
niche
[] Push in and up to remove. Cover is
dishwasher safe.
[] Clean the sensors, left and right, in
the waste container niche. The
sensors read if the waste container is
inserted and if it needs to be
emptied.
38
Common
Capsule
p_ate
Steam
coffee
system
care
vaJve
The capsule plate will soil more or less
depending on the oil content of the
coffee capsule used,
Clean the capsule plate as necessary
or when the machine needs to be
descaled with the supplied cleaning
tablets, The cleaning tablets can be
purchased from Miele,
[] Press the steam lever down and pull
off the rubber sleeve,
[] Clean the rubber sleeve and the
steam valve tip with a mild solution of
water and liquid dish soap,
[] Reattach the rubber sleeve firmly on
the steam valve tip,
[] Press the checkered part, '_, down
and pull the capsule plate, ,'_, out,
[] Push the steam lever up before
closing the door or else it may get
damaged,
[] Dissolve one cleaning tablet in hot
water,
[] Place the capsule plate in the
solution and let it soak for one hour,
[] Rinse thoroughly and dry the capsule
plate,
[] Insert the capsule plate into the
machine until it clicks,
39
Common
coffee
system
care
Exterior
Cappuccinatore
The front of the appliance can be
cleaned with a sponge and a solution of
warm water and non abrasive liquid
dish soap. Dry with a soft cloth.
Clean the cappuccinatore after every
use, otherwise it may become blocked
with dried milk and hard to clean.
//iii_
Wiiiiiiiiiiiiiii_i_
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii@iiii_
Only use a slightly damp sponge
when cleaning the controls. Water
could penetrate into the electronics
and cause damage.
Wipe any spills from descaling
immediately!
Stainless
steel surfaces
[] Press the spout together from the top
and bottom to pull out the two pieces
of the spout together. See below.
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner.
To help prevent soiling, a conditioner
for stainless steel can also be used.
Apply sparingly with even pressure.
Jog shuttles
Clean the jog shuttles with a sponge
and a solution of warm water and liquid
dish soap.
[] These jog shuttles may become
discolored or damaged if not cleaned
regularly. Do not use a stainless steel
cleaner on the jog shuttles.
4O
[] Take the cappuccinatore
clean.
apart and
Common
coffee
system
care
Maintenance
The perforator should be changed after
15000 cups of coffee / espresso, The
_erforator can be purchased from Miele,
It is recommended to contact the
Miele Service department for
assistance in performing this
maintenance task.
[] Reassemble the lid as shown in the
graphics.
[] Be sure that the valve sits above the
[] Turn the left jog shuttle to "Settings",
cappuccinatore handle. Otherwise
the frothing process will not work,
[] Turn the right jog shuttle to
"Maintenance",
[] Press the right iog shuttle and turn it
to "carry out",
[] Press the right jog shuttle,
41
Common
coffee
system
care
The right display goes dark and the
appliance is now lowering the
perforator.
[] Open the appliance door.
[] Pull out the capsule plate.
il Z_ D° not reach up into the
perforator opening. Danger of injury!
[] Screw the new perforator firmly into
the unit. The spring and ball bearing
must be inserted in the perforator
opening so that the ball bearing is on
top.
[] Insert the rubber disc from the
bottom up (with the funnel pointing
downwards).
[] Insert the capsule plate and close the
door.
[] Pull the rubber disc top, down and
out.
[] Insert the tool for removing the
perforator up into the unit, _. Turn it
to the left, ,'_, to loosen and remove
the perforator.
42
Descaling
the appliance
The coffee system must be descaled
regularly. The time period depends on
the water hardness seL The appliance
will display a reminder message and
will eventually lock if not descaled.
DescaHng
Once the system is at the point where
only 50 drinks can be prepared before
descaling must be performed, the
display will show "50 no. of uses until
descaling has to be done". This
message will appear and countdown
after each drink. When the count is to
zero, the coffee system will lock and the
left display will show "Descale" _. The
right display will show "confirm to startL
[] Turn the left knob to the "Descaling"
symbol.
[] Press the right jog shuttle to start the
descaling process.
The appliance can only be used again
once descaling is performed.
Only use the encJosed descaHng
tabJets for descaling. The descaling
tablets are specially designed for
this coffee system. The descaling
tablets can be purchased from your
local Miele dealer or Miele.
This is a safety feature to ensure the
process will be completed.
Descaling is important to increase
the life of the machine and to ensure
the best results possible.
Other agents may damage the
machine and affect the taste of
coffee and hot water.
Be sure that the correct mixture of
descaling agent and water are used
to prevent damage to the machine.
To prevent damage to the exterior
wipe up any descaling solution
spills immediateJy!
Thoroughly clean the water tank
and the drip tray of desealing
residue.
43
Descaling
the appliance
The right display will prompt you
through the single steps of the
descaling process.
Follow these prompts.
See "Descaling prompts" for more
information,
any steps
i Do not skip
and do not
remove a part untess prompted by
program to fault and descaling will
i restart.
he display. This will cause the
44
At the beginning of the descaling
program there will be a delayed start to
allow the tablets to completely dissolve,
If the machine has not sufficiently
cooled after use to begin the descaling
program the delay start time will be
extended.
A pump will introduce a small amount
of descaling solution into the system
then rest briefly to allow the solution to
take effect. The right display indicates
how long the process will take,
Descaling
DescaHng
the appliance
prompts
For clarification regarding the prompts see the following:
Ptease add descaling
water container
agent to the
[] Remove the water tank,
[] Fill the water tank with cold tap water
to the _ mark, If not filled to the
mark, descaling will be prematurely
canceled,
Please empty drip tray
(and waste container)
[] Since the machine is also rinsed
inside, the drip tray needs to be
emptied to continue,
[] Also empty the waste container at
this time,
[] Dissolve two of the enclosed
descaling tablets in the water tank,
Ptease fill with fresh water
[] Close the water tank and insert it into
position,
[] Take the water tank out, rinse out any
descaling residue thoroughly with
water,
Please use the waste container
[] Take the waste container from the
interior and set it under the coffee
[] Fill with fresh water to the "Max," mark
and reinsert the tank,
dispenser and steam valve,
PJease use descating
close the door
funnel and
[] Open the door and remove the
capsule plate,
[] Insert the co!ored funnel into the
capsule plate opening,
45
Fault messages
If an error occurs a fault message will appear in the right display_ Minor problems
can be fixed without a service call,
Message
Possible fauJt
Fix
Chamber empty please refill
The selected coffee chamber is empty,
Fill wkh coffee capsules,
Please fill with fresh water
This is a reminder to fill the water tank
with fresh water when the machine is
turned on,
Please set the time of day
The machine was disconnected from
the power supply and the time of day
needs to be reset,
Set the time of day,
Empty drip tray and clean
contacts
The drip tray is full and/or the metal
contact sensors on the tray are soiled,
Empty and clean the drip tray,
Clean and dry the contacts,
Please use descaling
funnel and close the door
The capsule plate needs to be taken
out and replaced by the descaling
funnel,
Remove the capsule plate and
insert tile colored funnel,
Please insert capsule
The capsule plate or perforator are
Insert the capsule plate or
plate
missing or the descaling
the machine,
:>erforator,
Please insert carousel
The carousel is missing or the sensor
under the carousel tray is soiled,
Insert the carousel and clean
the sensor with a cloth,
Please open tile valve
Steam cannot be supplied
valve is closed,
Press the steam lever down,
Please close the valve
The steam lever is still pressed down,
Push the steam lever up,
Maintenance
The perforator needs to be replaced
after about 15,000 cups of coffee,
Turn the left jog shuttle to
"Settings", Turn the right jog
shuttle to maintenance and
required
funnel is still in
if the steam
change the perforator (see
"Common coffee system care A
Maintenance"),
Confirm to start
The selected process is prompted to
start,
Press the right jog shuttle,
Confirm to continue
The descaling
Press the right jog shuttle,
Empty
A coffee chamber was selected which
needs to be continued,
has not been allocated to a coffee type,
Allocate a type of coffee to the
chamber,
No. of uses until
The machine counts the number of
Descale the machine
descaling
drinks made before descaling has to be
carried out, Once this number reaches
zero, the machine locks until the
(see "Descaling the
appliance"),
has to be done
descaling process has been
successfully completed,
46
Frequently
Machine
asked questions
Problems
-
Is the unit locked?
If not, the light bulb has burnt out,
Contact the Miele Service Department,
-
Is the lighting set too low?
Adjust the lighting,
The unit has no power,
m
m
Is the main switch turned off?
Is the machine plugged in?
Check that the fuse is not defective,
If so contact the Miele Service
DepartmenL
-
Is the machine plugged in?
-
Plug the machine in,
-
Is the machine programmed to
switch off after a programmed
time?
-
The machine turns off into standby
mode when not used for the
-
The water temperature
high,
-
may be too
programmed time,
The unit is blocked until the water has
cooled,
47
Frequentny
asked questions
The light turns off automatically when the machine has not been used for 10
minutes,
The steam lever is not pushed up all the Press the lever down and then up again
way,
all the way,
If the machine was unplugged or a
power failure occurred,
Reset the time of day,
The preset times for turning on or off
automatically are saved in the memory
and do not need to be reset,
-
The contacts are soiled,
-
Clean and dry the contacts,
-
The drip tray is not inserted correctly,
-
Insert the drip tray correctly,
-
Turn the machine off and on again
with the main switch,
-
If the message still appears contact
Technical Service,
-
48
If the coffee system has still a temperature of 140 °F (60 _C) or higher, the
machine will not be rinsed,
Frequentny
Preparing
/ dispensing
asked questions
problems
Take out the water tank and then insert it again,
A coffee capsule is jammed in the
carousel,
[] Open the appliance
door,
[] Pull the carousel tray out, lift out the
capsule carousel and make sure all
capsules can move easily,
[] insert the carousel in the tray and
push it all the way in,
[] Close the door.
[] Take out the water tank and then
insert it again,
If still no or little water is dispensed the
steam valve is clogged,
[] Open the appliance
door,
[] Press the steam lever down and pull
off the rubber sleeve,
[] Using the small end of the provided
tool unscrew the top of the steam
valve counterclockwise,
[] Clean the tip and screw it on again,
49
Frequentny
asked questions
Steam can be dispensed as long as the Once cooled the system will no longer
steam heating system is warm,
dispense steam,
The rubber odor will wear off with time and usage,
-
Is the spout turned to the side so that froth can only be prepared in the
cappuccinatore?
Turn the spout to the cup,
-
Are the valve and the froth dispenser
of the cappuccinatore properly
inserted in the lid?
-
See "Common coffee system care Cappuccinatore",
-
Are any single parts of the
cappuccinatore clogged?
-
Clean the cappuccinatore,
If a double espresso / coffee was
selected the machine uses two coffee
capsules,
5O
Dispensing is interrupted when the
carousel chambers are empty, Refill
coffee capsules,
Frequentny
Coffee
results
The capsule plate is soiled,
-
asked questions
Clean the capsule plate,
If the maximum water amount is
reached, the water dispensing stops
automatically, The maximum water
amount is saved,
-
There was not enough water in the
tank, The dispensed water amount
will not be saved,
-
Refill the water tank and reset the
serving size,
Depending on coffee type the grinding level will differ between coarse and fine,
Preparing time and amount will vary,
-
Check if the capsule plate is
clogged,
Clean the capsule plate,
Prewarm the cup,
This is residual water from the cleaning process, Pour water away,
The capsule plate is not inserted all the
way,
Take the capsule plate out and insert it
again,
-
Check the water amount saved in the memory per coffee,
Adiust if necessary,
-
After 15000 cups of coffee the
perforator needs to be replaced,
See "Common coffee system care Maintenance" after checking the
coffee counter,
51
Frequentny
DescaHng
asked questions
problems
The descaling process cannot be
interrupted once the right iog shuttle is
pressed, The process now needs to be
completed as a safety measure,
Descaling is important to increase the
life of the machine and to ensure the
best results possible,
The machine needs to be descaled,
52
See "Descaling the appliance",
Frequentny
asked questions
"F" messages
-
-
No water can be pumped from
the water tank,
F 10 also shows, if the water tank
was not filled correctly during
descaling,
There is a slight fluctuation in the
electrical supply,
-
Fill the system with water, See "Before
using the coffee system for the first
time",
-
Remove and reinsert the water tank,
-
Refill to the mark and restart descaling,
-
If the message still shows, call the
Technical Service,
Call Technical Service if the message
appears regularly,
A coffee capsule has jammed above [] Open the appliance door,
the waste unit,
[] Remove, empty and return the waste
unit,
A coffee capsule has jammed,
[]
Close the dock
[]
If the message still shows, see
"Removing a jammed capsule from the
carousel tray",
[] Open the appliance
door,
[] Remove, empty and return the waste
unit,
If the message still shows, open the
appliance door and follow the prompts in
the right display,
See "Removing a jammed capsule from
the capsule plate",
Call the Miele Technical Service DepartmenL
53
Removing
a jammed
From the carousel
capsule
tray
From the capsule ptate
[] Take the carousel and the capsule
plate out.
[] Open the appliance door.
[] Turn the machine off at the main
switch.
[] Insert a spoon handle underneath the
carousel tray on the right side. Move
the spoon handle with care to the left
side.
[] On the right side of the capsule plate
is an opening. Check if a coffee
capsule has jammed in there or
further up in the uniL
[] Pull out the carousel and remove the
coffee capsule.
[] Throw out the capsule so it does not
jam again. It may be damaged or
dented.
[] Remove the tray by pulling it
completely out then pushing it up
slightly. Clean the area underneath it,
making sure to wipe clean the sensor.
Reinsert the tray.
[] Turn the machine on at the main
switch.
[]
[] Reinsert the capsule plate and the
carousel in the tray platform.
[] Turn the machine on at the main
switch.
[]
[] Close the door.
[]
[] If the message still appears call
Technical Service.
54
Remove the coffee capsule onty with
a wooden spoon handle.
Close the door.
If the message still appears contact
Technical Service.
After saJes service
In the event of a fault which you cannot
correct yourself please contact the
Miele Technical Service Department,
1-800-999-1360
techserv@mieleusa,com
1-800-565-6435
service@miele,ca
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance
given on the data plate inside the
appliance,
55
Electdca!
connection
The coffee system comes equipped
with a 6 ft. (!.8 m) power cord with a
NEMA 5-!5P molded plug for
connection to a 120 V, 15 A, 60 Hz
power supply,
Connection should be made via a
suitable isolator, with an on-off switch
which should be easily accessible for
servicing work.
Installation, repairs and other work by
unqualified persons could be
dangerous. The manufacturer cannot
be held responsible for unauthorized
work.
Verify that the voltage, load and circuit
rating information found on the data
plate, match that of the household
electrical supply before installing the
coffee system.
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or call Miele's
Technical Service Department.
1-800-999-1360
1-800-5GS-GSS5
56
installation
mnstallation
options
The coffee system is designed to be built into cabinetry,
"d
57
JnstaJJation
6OO
COco
AI
<
_t
58
installation
If the machine is installed in combination with other Miele appliances,
installed with a protective base between the appliance and the uniL
it should be
>-,98
:_NIu ....
:
03
k£)
'IH /z
, f,,_
59
JnstaJJation
A display cabinet is also available from Miele or your local dealer as an installation
option,
co
The display cabinet is intended to hold the CVA 2660 and an optional ESS 2060
Storage Drawer or EGW 2060 Cup Warmer,
6O
installation
hstallation
Make sure power is not supplied to
the appliance while installation or
maintenance work is performed.
Disconnect the power supply to the
work area by unplugging the unit,
tripping the circuit breaker or
removing the fuse. The coffee
system must be properly installed
before being used.
[] Plug the appliance
outleL
into the electrical
[] If you have a cabinet with 3/4"
(19 mm) side panels, you have to drill
four holes firsL
- Center the machine in the
cabinet.
-
[] Open the door and partially tighten
the screws by hand. Do not use an
electric screwdriver.
[] Carefully turn the lower screws to
center the machine.
[] To fix the machine in the cabinet,
tighten the upper screws.
Tighten the screws iust so they
leave a mark in the panel.
Remove the machine from the
cabinet and drill four holes 1/,16.
(2 mm) with a diameter of /1_
(4.5 mm).
[] Level the machine with the four
height adiustable feet.
The feet can be turned out up to s/s"
(10 mm).
[] Push the appliance all the way back
into the cabineL
61
installation
Programming
The appliance must be correctly'
installed and connected before the
first use.
You will then be prompted to select a
language.
[] Turn the right jog shuttle until the
desired language shows in the
display.
Setting the Janguage
[] Press the right jog shuttle to confirm.
[] Press the left jog shuttle to turn the
machine on.
To turn off the machine
[] Press the left jog shuttle until the
displays go dark.
When turned on for the first time, a
welcome screen as well as other
messages will appear in the right
display. The welcome screen will be
displayed each time the machine is
turned on until 5 drinks (including
steam) have been prepared.
The displays lighL
62
installation
Setting the water hardness
The hardness of the water used in the
coffee system must be determined and
programmed into the appliance. The
water hardness will determine how
frequently the unit must be descaled to
properly maintain the coffee system.
The machine monitors the volume of
water passing through it in conjunction
with the hardness of the water and will
indicate when descaling is necessary.
Your local water authority can inform
you of the hardness of your tap water or
you can measure the hardness yourself
usinc the enclosed test strip.
Hardness
1 1 (soft)
Hardness 2
1 (soft)
Hardness 3
2 (medium)
Hardness 4
3 (hard)
4 (very hard)
0 -3
0 - 130
4 -7
130 - 250
7 - 14
250 - 380
14 --21
over 21
over 380
To adjust or set the water hardness
[] Turn the left iog shuttle to "Settings".
[] Turn the right jog shuttle to the
"Programming" symbol, press to
confirm.
[] Dip the strip into your tap water for
one second, then shake off any
excess wateL
The result will be evident after one
minute.
[] Turn the right jog shuttle to the "Water
hardness" symbol, press to confirm.
[] Turn the right iog shuttle to set the
water hardness.
A check marks the current setting.
non-carbonated
mineral water to
prevent excessive lime scale build
up. Never use distilled water.
[] Press the right jog shuttle to save the
setting.
The display now shoves the main screen.
The back symbol@
s selected.
[] Press the right jog shuttle to return to
the main display menu.
63
Coffee glossary
Caff_ is the kalian term for a standard
espresso.
Caff_ americano is a thin espresso
with water added.
Caff_ corretto is espresso with a
splash of liquor.
Caff_ freddo
is iced coffee. An
extended version of espresso served
with ice.
Caff_ latte is a double espresso in a
large cup filled with hot milk, topped
with little or no foam.
Caff_ moca consists of equal parts of
espresso, hot milk and cocoa.
Caff_ dstretto is the strongest most
concentrated espresso. The water is
reduced to 2 tablespoons (30 ml) per
serving.
Caffeine - the caffeine content of
espresso is only a third or half of that
found in coffee. The stronger the roast,
the less caffeine the espresso will
contain.
Cappuccino is espresso with frothed
milk. It is equal parts of espresso, hot
milk and foam.
Cappuccino chiaro is a "light"
cappuccino with less espresso and
more hot milk.
64
Cappuccino scuro is a "dark"
cappuccino with more espresso and
less hot milk.
Cappuccino senza schiuma is a
cappuccino without the froth.
Crema is the sign of the perfect cup of
espresso - a fine, nut or cinnamon
brown foam on the surface of the
espresso, which is only created when
the pressure is sufficiently high. The
crema contains the foamed oils which
are rich in flavor and aroma.
Espresso,
see Caff&
Espresso corto is a "short", strong
espresso.
Espresso doppio
normal espresso.
is a double portion of
Espresso tungo is the longer, less
concentrated version served in a
standard coffee cup.
Espresso dstretto is a double
strength, bitter tasting espresso.
Macchiato is espresso with a dollop of
hot, foamed milk giving a dappled
(macchiato) appearance.
Pre-warming the cups is
recommended to prevent the espresso
from cooling too quickly.
The Espresso
range
Flistretto (black)
is the typica! Italian espresso. It is a
short, strong, full-bodied espresso with
a touch of acidity. It has a pleasantly
lingering taste.
Mvanto (copper brown)
A very well balanced blend, Livanto is
characterized by a dense and velvety
aroma. It is a uniquely rounded
espresso.
Strength: 10
Ideal cup size: Ristretto, Espresso or
Cappuccino
Strength: 6
Ideat cup size: Espresso or Lungo
Arpeggio (dark purple)
is a Mediterranean blend par
excellence with a strong character,
intense body and long exquisite
after-taste. Its thick, smooth crema
remains to the last sip.
Strength: 9
Ideal cup size: Ristretto, Espresso or
Cappuccino
Ftoma (dark gray)
With its sweetness and its woody notes,
Roma is the ideal coffee for a short
espresso that is not too strong.
Strength: 8
Ideal cup size: Ristretto or Espresso
Oecaffeinato lntenso (brick red)
An intense, rich taste with slightly
elevated acidity gives this
decaffeinated coffee all the strength of
a true espresso.
Strength: 7
Ideal cup size: Espresso or
Cappuccino
Capriccio (dark green)
is a full-bodied espresso, which is also
creamy, mild and rich. Its crema is very
dense, and so delicate that it reflects
the light.
Strength: 5
Ideal cup size: Espresso
Vo!luto (yellow gold)
Lightly roasted but full-bodied, Vo!luto's
flavor is round and fresh with a cereal
hint. Vo!luto's character is reinforced by
a touch of acidity.
Strength: 4
Ideal cup size: Espresso
Cosi (dark brown)
is perfect for espresso lovers who enioy
a mild, smooth crema coupled with the
refreshing acidity of a hint of lemon.
Strength: 3
Ideal cup size: Espresso or Lungo
Decaffeinato (red)
This is the lighter and creamier
decaffeinated blend, offering a rich and
delicate balance between mildness and
acidity. Decaffeinato's crema is
distinguished by its hazel color and
consistent texture in the mouth.
Strength: 2
Ideal cup size: Espresso or Lungo
65
The Lungo range
Vivalto (sky blue)
is an intense Lungo which combines a
beautifully roasted note with a subtle
floral note. With its noticeable crema
and mild aroma, it is also delicious
prepared with milk.
Strength: 6
Ideal cup size: Lungo
Deeaffeinato Lungo (coral}
delivers a smooth body and a fine
roundness in the mouth. Its sustained
roasting reveals flavorful grilled notes.
Strength: 5
Ideal cup size: Lungo
Finezzo (butter yellow)
Extremely balanced, Finezzo is a
mellow, gently fruity blend that
blossoms within its light body. Its
character is reinforced by a hint of
acidity.
Strength: 4
Ideal cup size: Lungo
66
Caring
Disposa_
of packing
materia_
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocatio!!
Disposa_
for the environment
of an o_d appliance
Old appliances may contain
that can be recycled. Please
your local recycling authority
possibility of recycling these
materials
contact
about the
materials.
Ensure that the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet, cut
off its power cord and remove any
doors to prevent hazards.
67
When contacting the Technical Service,
please quote the model and serial number
of your appiianceo
MieJe, Jnc,
MieJe Limited
Nationam Headquarters
9 Independence Way
Princeton, NJ 08540
Phone: 800=843=7231
609=4t 9=9898
Fax:
609=419=4298
www.miele.com
National Headquarters
55G East Beaver Creek Road
Richmond Hill, ON L4B 1E5
Phone: 800=643=5381
905=707=1171
Fax:
905=707=0177
www.miele.ca
info@miele.ca (general enquiries)
professional@miele.ca (commercial
Technical Service & Support
Nationwide
Phone:800=999=1360
Fax:
888=586=8056
Akeration rights reserved
CVA 2660
/4105
c_j_
enquiries)
Mieiecare Nationam Service
Phone:800=565-6435
905=850=7456
Fax:
905=850=6651
service@miele.ca(Tech. Service)
M,-Nr, 06541300/01
en/US/CDN