Audiovox FPE-1908DV Owner`s manual

FPE1908DV
19” HD FLAT PANEL LCD
TV/DVD COMBO
OWNER’S MANUAL
1
FOR ASSISTANCE CALL CUSTOMER SERVICE AT 1-800-645-4994
OR VISIT US AT WWW.AUDIOVOX.COM
128-8329
E-1
English P1-32.indd 1
6/11/2008 12:22:10 PM
Safety Precautions
Placement INFORMATION
• Do not use this unit in places that are extremely
hot, cold, dusty, or humid.
• Do not restrict the airflow of this unit by placing
it somewhere with poor airflow, by covering
it with a cloth, or by placing it on bedding or
carpeting.
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE. DO NOT PLACE OBJECTS FILLED
WITH LIQUIDS ON OR NEAR THIS UNIT.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
Safety INFORMATION
• When connecting or disconnecting the AC
power cord, grip the plug and not the cord itself.
Pulling the cord may damage it and create a
hazard.
• When you are not going to use the unit for a long
period of time, disconnect the AC power cord.
Condensation INFORMATION
• When left in a heated room where it is warm
and damp, water droplets or condensation may
form inside the unit. When there is condensation
inside the unit, the unit may not function
normally. Let the unit stand for 1-2 hours before
turning the power on or gradually heat the room
and allow the unit to dry before use.
RATING PLATE LOCATION
The rating plate is located on the rear of the unit.
FCC Information
CAUTION
INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
This product contains
a low power laser
device.
The symbol for Class II
(Double lnsulation)
CAUTION:
• DANGER OF EXPLOSION IF BATTERY
IS INCORRECTLY REPLACED. REPLACE
ONLY WITH THE SAME OR EQUIVALENT
TYPE.
• TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT
OF WALL OUTLET, THEN FULLY INSERT.
• Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an AC power outlet
on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
WARNING: Changes or modifications to
this unit not expressly approved by the party
responsible for compliance could void the user
authority to operate the equipment.
E-2
English P1-32.indd 2
6/11/2008 12:22:11 PM
IMPORTANT SAFETY PRECAUTIONS
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near
water.
6.
Clean only with a dry cloth.
7.
Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
8.
Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose
of the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has two
blades and a third grounding prong.
The wide blade or the third prong
are provided for your safety. When
the provided plug does not fit into
your AC power outlet, consult an
electrician for replacement of the
obsolete outlet.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution
when moving the
c a r t / a p p a ra t u s
combination to
avoid injury from
tip-over.
13. Unplug this apparatus during
lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as the AC power cord or plug
is damaged, liquid has spilled
or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
10. Protect the AC power cord from being
walked on or pinched particularly at
the plug, convenience receptacles,
and the point where they exit from
the apparatus.
E-3
English P1-32.indd 3
6/11/2008 12:22:11 PM
TABLE OF CONTENTS
SAFETY PRECAUTIONS ................... 2
IMPORTANT SAFETY INSTRUCTIONS .
.......................................................... 3
TABLE OF CONTENTS ...................... 4
QUICK INSTALLATION .................... 5
DISC FORMATS ................................ 6
ACCESSORIES .................................. 7
GETTING STARTED .......................... 7
REMOTE CONTROL REFERENCE GUIDE
..................................................... 8 - 9
UNIT REFERENCE GUIDE ....... 10 - 11
CONNECTIONS ...................... 12 - 15
Connecting a TV Antenna/Cable/
Satellite ...................................... 12
Connecting an A/V Device ..........12
Connecting Devices with a Composite
(Yellow RCA-Type) Video Output .......
................................................... 13
Connecting Devices with a Composite
(Yellow RCA-Type) Video Input ... 13
Connecting a High-Definition (HD)
Source ........................................ 14
Connecting a PC ........................ 14
Connecting an Audio Amplifier
External Speaker ........................ 15
Connecting the AC Power Cord .. 15
INSTALLATION .............................. 16
USING HEADPHONES ................... 17
SOUND SYSTEM ............................ 17
TV SETUP ................................ 18 - 22
PICTURE Menu .......................... 18
AUDIO Menu ............................ 18
TIME Menu ................................ 19
Setup Menu ......................... 19-20
Parental Menu .................. 20-21
TV Menu .................................... 22
CD/DVD OPERATION ............ 23 - 24
Playing a Disc ............................ 23
Playing a Picture File Disc .......... 23
Pausing Playback (Still Mode) ..... 23
Stopping Playback ...................... 23
Skipping to a Different Track ..... 24
Fast Forward/Fast Reverse ........... 24
Slow-motion Play (DVD) ............ 24
Audio Selection (DVD) ............... 24
Subtitle Selection (DVD) ............ 24
Angle Selection (DVD) ............... 24
SPECIAL FUNCTIONS .................... 25
Display Function (DVD) ............. 25
Locating a Specific Title (DVD) ... 25
.Locating a Specific Chapter/Track ......
................................................... 25
Locating a Specific Time ............. 25
REPEAT PLAYBACK ......................... 26
Repeating a Chapter/Title (DVD) ........
................................................... 26
Repeating a Single Track/an Entire
Disc (CD) ................................... 26
.Repeating a Specific Section (DVD/
(CD) ........................................... 26
DVD PROGRAMMABLE PLAYBACK ......
........................................................ 27
Programmable Memory .............. 27
Title/Chapter Programmed Playback
(DVD) ..................................... 27
CUSTOMIZING THE DVD FUNCTION
SETTINGS ................................. 27-28
Language Setup .......................... 27
Video Setup ............................... 28
System Setup .............................. 28
MAINTENANCE ............................. 29
TROUBLE SHOOTING GUIDE ..............
................................................. 29 - 30
E-4
English P1-32.indd 4
6/11/2008 12:22:11 PM
Quick Installation
When you turn on your television set for the
first time, be sure to place it on a solid stable
surface. To avoid danger, do not expose the TV
to water, or a heat source (e.g. lamp, candle,
radiator). Do not obstruct the ventilation grid
at the rear and be sure to leave sufficient gaps
around the unit as shown.
Turning On the Unit for the first time
The first time you turn on the unit, the unit will enter SETUP mode. You can easily follow the
prompt message on the screen to complete basic TV settings.
Make sure the RF aerial has
been connected properly to the
TV antenna input jack on the rear
of the unit.
2. Use the
/
button to select Antenna,
then press the
/ button to select Air
or CATV.
1. Press the / button to select Yes. Press
the ENTER button to proceed with the
initial setup.
3. Use the / button to select Auto Scan, then press the button to enter auto scan menu.
Use the / button to select Start to Scan, then press the button to begin scanning. (If
you selected CATV on Step 2, you need to select Cable System before Start to Scan). The
system will automatically start to scan and preset all available TV channels.
4. After scanning has finished, the system will return to the first TV channel scanned.
E-5
English P1-32.indd 5
6/11/2008 12:22:13 PM
DISC FORMATS
This unit can playback:
DVDs
[8cm/12cm disc]
audio cds
[8cm/12cm disc]
CD-R/CD-RW
Region Management Information
Compatible
Region Management Information: This unit is designed and manufactured to respond to the Region
Management Information that is encoded on DVDs. If the region number printed on the DVD does not
correspond to the region number of this unit, this unit cannot play that disc.
The region number of this unit is
1
.
Disc Function or Operation that is Not Available
When the symbol appears on the screen, it indicates that the function or operation attempted is not
available at that time. This occurs because the DVD manufacturer determines the specific functions.
Certain functions may not be available on some discs. Be sure to read the documentation provided
with the DVD.
Icons Used on DVDs
Language selections for audio
Sample lcons
Note:
• When playing back a CD-G
(Graphics) or CD EXTRA disc,
the audio portion will be played,
but the graphic images will not be
shown.
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
1
Region code indicator
TitleS, ChapterS and Tracks
• DVDs are divided into “titles” and “chapters”. If
the DVD has more than one movie on it, each
movie would be a separate “title”. “Chapters”
are sections of titles.
• Audio CDs are divided into “tracks”. A “track”
is usually one song on an Audio CD.
Note:
• Numbers identify each title, chapter, and track on
a disc. Most discs have these numbers recorded
on them, but some do not.
Notes on Unauthorized Discs:
You may not be able to play some DVDs on this unit if they were purchased from outside your geographical
area or made for business purposes.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted
material without permission.
Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132; and 5,583,936
licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is prohibited.
E-6
English P1-32.indd 6
6/11/2008 12:22:14 PM
Accessories
Please LOCATE the INCLUDED accessories.
.Remote Control ........................................................................................................ x 1
.AAA Batteries ........................................................................................................... x 2
Specifications and appearance are subject to change without notice.
GETTING STARTED
Using the Remote Control
• Point the remote control at the REMOTE SENSOR located on the unit.
• When using this unit in bright light, the infrared REMOTE CONTROL SENSOR may not work
properly.
• The recommended effective distance for using the remote control is about 16 feet.
TO CHANGE THE REMOTE CONTROL BATTERies
1. Open the battery door. 2. Insert two “AAA” batteries.
BATTERY REPLACEMENT
When the batteries become weak, the operating distance of the remote control will be greatly
reduced and you will need to replace the batteries.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Note: •If the remote control is not going to be used for a long time, remove the batteries to
avoid damage caused by battery leakage corrosion.
•Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC)
or rechargeable (NICKEL-CADMIUM) batteries.
•Always remove batteries as soon as they become weak.
•Weak battery can leak and severely damage the remote control.
WARNING:
Do not dispose of batteries in a fire. They may leak and/or explode.
Many universal remote controls have a “learning” feature. We recommend you use that feature
to program the remote control.
For any questions or problems related to programming a universal remote control, you must
contact the customer service department of the universal remote control manufacturer for
assistance, or refer to the instructions included with the universal remote control. We cannot
offer assistance in programming universal remote controls.
E-7
English P1-32.indd 7
6/11/2008 12:22:14 PM
remote CONTROL REFERENCE GUIDE
5. MENU Button
Press to display the on-screen TV
menu.
6. VOLUME (- / +) Buttons
Press to adjust the volume level.
7. CURSOR ( , , , ) Buttons
Press to highlight selections on a menu
screen and adjust certain settings.
ENTER Button
Press to confirm selections on a menu
screen.
8.
/
Buttons
: Fast reverse playback.
: Fast forward playback.
9. PREV
Button
Press to select previous chapters or
tracks on a disc.
10. SUBTITLE Button
Press to select one of the subtitle
languages programmed on a DVD.
11. ANGLE Button
Press to switch the camera angle of the
video presentation when scenes with
multiple camera angles are recorded
on a DVD.
12. TITLE Button
Press to show title menu.
13. GOTO Button
Press to skip directly to a specific
location on a DVD/CD.
14. MEMORY Button
Press to set predetermined playback.
CLEAR Button
Press to clear input selections.
15. MTS (Multi Channel Television Sound)
Button
Press to select between MONO sound,
STEREO sound and Secondary Audio
Program (SAP).
CC Button
Press to activate the Closed Captioning
feature. This function only works on
programs broadcasted with captions.
16. EXIT Button
Press to exit the TV SETUP menu and
return directly to normal viewing.
SLEEP Button
Press to set the SLEEP timer. The unit
will remain on for the time that is
set, and will automatically shut off
afterwards.
1.
STANDBY / ON Button
Press to turn ON the unit or put it in
STANDBY (OFF) mode.
2. TV Button
Press to switch to TV mode.
DVD Button
Press to switch to DVD mode.
AV Button
Press to switch to source connected to
AV1 (composite) inputs.
HD Button
Press to switch to source connected to
YUV in (component) inputs.
3. Number (0 - 9) Buttons
4.
[dot] Button
Press to enter digital sub-channels (i.e.
11.3 or 12.7)
E-8
English P1-32.indd 8
6/11/2008 12:22:15 PM
remote CONTROL REFERENCE GUIDE
22. Button
Press to stop playing a disc.
PLAY Button
Press to start and resume playback of a
disc.
PAUSE Button
Press to pause playback and single
frame advance.
23. AUDIO Button
Press to select audio soundtracks on a
DVD or change the output mode of a
CD.
24. SLOW Button
Press to perform slow forward playback
of a DVD.
25. DVD MENU Button
Press to enter the main menu of the
DVD.
26. SETUP Button
Press to enter and exit the SETUP menu
of the DVD.
27. A-B Button
Press to perform point-to-point repeat
playback on a DVD or CD.
REPEAT Button
Press to repeat a chapter or title of a
DVD.
Press to repeat a single track or whole
CD.
28. DISPLAY Button
Press to change disc status information
displayed on the screen.
SOUND Button
Press to select from preset sound
settings to match the type of show
you are watching (Music / Standard /
Personal / Movie).
29. LCD MODE Button
Press to set size of LCD display (WIDE
/ 4:3 / LCD OFF).
PICTURE Button
Press to select from preset screen
display settings to match the type of
show you are watching (Standard / Soft
/ Movie / Personal).
17. FUNCTION Button
Press to switch between TV / AV In /
YUV In / DVD / PC In.
18. LAST CH Button
Press to switch repeatedly between the
last two channels displayed.
19. MUTE
Button
Press to turn off the sound.
20. CH
/ CH
Buttons
Press to change the TV channels.
21. NEXT
Button
Press to select the next title, chapter or
track on a disc.
E-9
English P1-32.indd 9
6/11/2008 12:22:15 PM
UNIT REFERENCE GUIDE
FRONT, LEFT & right SIDE VIEW
1) Color LCD Screen
2)
Button
Press to turn the unit on and off.
3)
PLAY Button
Press to start or resume playback of a
disc.
4)
STOP Button
Press to stop playing a disc.
5) MENU Button
Press to enter and exit the TV menu.
6) FUNCTION Button
Press to select TV, AV In, YUV In, DVD,
or PC In.
7) CH Buttons
Press to select a TV channel.
Button
Press to select previous chapters or
tracks on a disc.
Button
Press to select the next title, chapter or
track on a disc.
8)
9)
– VOL + Controls
Press to adjust the volume level.
STANDBY Indicator
Indicates whether the unit is ON or in
STANDBY (OFF) mode.
Light On: The unit is in STANDBY.
Light Off: The unit is turned ON.
Remote Sensor
Do not block this sensor or remote
control will not work.
10)Disc Door
Push gently to close the disc door.
11) PUSH OPEN Button
Press to open the disc door.
12)Removable Stand
13)Speakers
E - 10
English P1-32.indd 10
6/11/2008 12:22:16 PM
UNIT REFERENCE GUIDE
bACK VIEW
14) AC Power Cord
15) VIDEO OUT Jack - AV OUT
16) AUDIO OUT Jacks (Left/Right) - AV
OUT
17) VIDEO IN Jack - AV IN
18) AUDIO IN Jacks (Left/Right) - AV IN
19) MONITOR/VGA Jack - PC IN
20) AUDIO Jack - PC IN
21) COMPONENT VIDEO IN Jacks (Y/PB/
PR) - YUV IN 22) AUDIO IN Jacks (Left/Right) - YUV IN
23) S-VIDEO Jack - AV IN
24) HEADPHONES Jack
25) TV Antenna Terminal
E - 11
English P1-32.indd 11
6/11/2008 12:22:17 PM
CONNECTIONS
Connecting a TV ANTENNA/CABLE/SATELLITE
To view television channels correctly, a signal must be received from one of the following
sources:
- An indoor or outdoor aerial antenna
- A cable system
- A satellite system
Connecting a Digital Antenna
The tuner in this TV receives ATSC TV
signals from an antenna.
This digital TV can receive standard
(SDTV) and high definition (HDTV)
over the air broadcasts.
Connecting an Analog Antenna
or Device
Satellite, cable, or
TV antenna cable
to TV ANTENNA
terminal (not
included)
The tuner in this TV receives NTSC TV
signals, analog cable signals or the RF
output from a satellite receiver, VCR
or cable box.
Connecting an A/V Device
Connecting to Devices with an S-Video Output
To connect to A/V devices such as a VCR, camcorder, satellite system or cable, etc.
Connecting to a VCR / Camcorder
/ Satellite System / Cable
Connect the AUDIO and S-VIDEO
cable (not included) as shown.
To AUDIO
IN jacks
(AV IN)
Make sure you connect the cable
from the other equipment (AUDIO
OUT and S-VIDEO OUT) to this
unit (AUDIO IN and S-VIDEO IN)
To S-VIDEO jack
(AV IN)
Note:
Please refer to the user manual
for the other equipment for more
information.
To AUDIO OUT and
S-VIDEO OUT jacks
E - 12
English P1-32.indd 12
6/11/2008 12:22:18 PM
CONNECTIONS
Connecting Devices with a Composite (yellow RCA-type)
Video Output
To connect A/V devices such as a VCR, video game system or camcorder:
Connecting to a VCR / Video Game System / Camcorder
Connect the AUDIO / VIDEO cable (not included) as shown.
Make sure you connect the cable from the other equipment (AUDIO and VIDEO OUT) to this
unit (AUDIO and VIDEO IN)
Note: Please refer to the user manual for the other equipment for more information.
To AUDIO
/ VIDEO IN
jacks
(AV IN)
To AUDIO / VIDEO OUT
jacks
Connecting Devices with a Composite (yellow RCA-type)
Video Input
To connect A/V devices such as a VCR, PVR or camcorder:
Connecting a VCR / PVR /
Camcorder
Connect the AUDIO / VIDEO cable
(not included) as shown.
Make sure you connect the cable
from the other equipment (AUDIO
and VIDEO IN) to this unit (AUDIO
and VIDEO OUT).
Note:
• Please refer to the user manual
for the other equipment for more
information.
• After connection, please operate
in TV/AV mode.
• For the reason of copyright
protection, the resulting copy
may have bad picture and/or
sound.
To AUDIO /
VIDEO OUT jacks
(AV OUT)
To AUDIO / VIDEO IN
jacks
E - 13
English P1-32.indd 13
6/11/2008 12:22:19 PM
CONNECTIONS
Connecting A HIGH-DEFINITION (HD) SOURCE
High-Definition (HD) Devices with component video output must be connected to the YUV
input.
Connect the component video cable and audio cable (not included) as shown.
Make sure you connect the component video cable and audio cable from the other equipment
(COMPONENT VIDEO OUT and AUDIO OUT) to this unit (COMPONENT VIDEO IN and AUDIO IN - YUV IN).
To AUDIO IN
jacks
To AUDIO
(YUV IN)
OUT jacks
* May require a subscription
for receiving HD channels.
Check with your cable/
satellite service provider for
details.
To COMPONENT
VIDEO IN jacks
(YUV IN)
To COMPONENT
VIDEO OUT jacks
Note:
When connecting a DVD player to the television, the picture resolution is solely dependent upon
the resolution supported by the DVD player attached. DVD player resolutions vary from 480i to
1080i, and this television can support DVD players up to a maximum resolution of 1080i. Connecting a pc
Connect the 15-pin D-SUB PC/VGA connector from your computer to the 15-pin D-SUB PC/
VGA input on this unit using a monitor cable and audio cable (not included) as shown.
Make sure you connect the
cable from the computer (PC
Connector and AUDIO - PC
OUT) to this unit (MONITOR /
VGA and AUDIO - PC IN).
To AUDIO jack (PC OUT)
To PC connector
E - 14
English P1-32.indd 14
6/11/2008 12:22:21 PM
CONNECTIONS
Connecting AN AUDIO AMPLIFIER/EXTERNAL SPEAKERS
This connection allows you to use an audio amplifier and external speakers.
Connect the AUDIO cable (not included)
as shown.
Make sure you connect the cable from the
other equipment (AUDIO IN) to this unit
(AUDIO OUT).
To AUDIO
OUT jacks
To AUDIO IN
jacks
Connecting THE AC POWER CORD
• Connect the AC power cord into a wall outlet.
• Press the
button on the left side of the unit or use the remote control to turn on the
unit.
Note:
• To prevent electrical shock,
match wide blade of AC power
cord to wide slot of AC power
outlet, then fully insert.
• Be sure the AC power cord is
disconnected and all functions are
off before making connections.
• Make sure all components are
connected correctly.
• When you are not going to use
the unit for a long period of time,
disconnect the AC power cord.
To AC wall
outlet
E - 15
English P1-32.indd 15
6/11/2008 12:22:22 PM
INSTALLATION
REMOVING THE BASE STAND
WARNING: The LCD Display is very fragile, and must be protected at all times when removing
the base stand. Be sure that nothing hard or sharp, or anything that could scratch or damage
the LCD display, come in contact with it. Do NOT place pressure on the front of the unit at any
time because the screen could crack.
1. Disconnect any cables or cords connected to the unit.
2. Lay the unit down on a flat surface, so the back side is facing up, making sure to place a soft
cushioned material (such as a pillow or thick piece of foam) beneath the screen.
3. Remove the four screws and then remove the BASE STAND from the unit.
MOUNTING ON THE WALL
This unit is VESA-compliant, and is designed to be wall-mounted with a VESA-compliant 3 15/16”
x 3 15/16” (100mm x 100mm) mounting kit designed for flat-panel TVs (sold separately). Mount
this unit according to the directions included with the mounting kit.
Note: You must remove the base stand before mounting the unit on the wall.
3 15/16”
3 15/16”
Four mounting
holes
E - 16
English P1-32.indd 16
6/11/2008 12:22:23 PM
USING HEADPHONEs
• Turn down the volume before connecting headphones to the unit, then adjust the volume to
your desired level.
• When headphones are connected, no sound will come from the front speakers.
Headphones
(1/8” [3.5mm] diameter plug)
Note:
Avoid listening to sound at high levels for prolonged periods of time. This may be harmful to
you and may cause hearing loss.
SOUND system
Dolby Digital (for DVD)
Dolby Digital is a sound system developed by Dolby Laboratories Inc. This unit automatically
recognizes DVDs that have been recorded with Dolby Digital.
Not all Dolby Digital sources are recorded with 6 channels.
Some sources marked Dolby Digital may be recorded in Dolby Surround, a 2 channel system.
Look for this logo on your unit.
Manufactured under license from Dolby Laboratories.
symbol are trademarks of Dolby Laboratories.
‘Dolby’ and the double-D
E - 17
English P1-32.indd 17
6/11/2008 12:22:23 PM
TV SETUP
Note: Some setting items on the menu screen may not activate depending on the mode selected
(TV / AV in / YUV in / DVD / PC in).
PICTURE MENU
1. Press the MENU button.
2. Press the button to enter PICTURE settings.
3. Use the or button to select the options
(Picture Mode, Contrast, Brightness, Sharpness,
Tint or Color). Adjust them using the or
button (Screen will change to your desired
setting).
4. Repeat step 3 to adjust other options.
5. To exit the MAIN MENU and return to the
normal screen, press the EXIT or MENU button
repeatedly.
Picture Mode : Select from preset screen display settings to match the type of show you are
watching (Standard, Soft, Movie & Personal). Select Personal mode to recall
your custom settings on contrast, brightness, sharpness, tint and color.
Contrast : Adjust to sharpen the picture quality. The black portions of the picture become
richer in darkness and the white become brighter.
Brightness : Adjust the brightness of the picture. Brighten or darken the whole picture.
Sharpness : Adjust the sharpness level to improve detail in the picture.
Tint : Adjust the tint of the picture (toward purple / toward green).
Color : Adjust the color of the picture.
AUDIO MENU
1. Press the MENU button.
or
button to select Audio,
2. Use the
then press the button to enter the Audio
settings.
3. Use the or button to select the options
(Sound Mode, Bass, Treble, Balance, Audio
Language or MTS). Adjust them using the or
button.
4. Repeat step 3 to adjust other options.
5. To exit the MAIN MENU and return to the
normal screen, press the EXIT or MENU button
repeatedly.
Note:
Experiment with different sound settings until you find the settings you prefer.
Sound Mode : Select from preset sound settings (Standard, Music, Movie or Personal) to
match the type of show you are watching. Select Personal mode to recall
your custom settings on bass, treble and balance.
Bass : Adjust the bass range.
Treble : Adjust the treble range.
Balance : Adjust the balance level toward the left or right speakers.
Audio Language : Select from English / Spanish / French. (Available for digital channels if
multiple audio languages are broadcasted.)
MTS (Multi Channel Television Sound) : Select Stereo / SAP (Secondary Audio Program) or
Mono.
Note:
The SAP (Secondary Audio Programs) feature allows a TV station to broadcast other information,
which could be audio in another language.
E - 18
English P1-32.indd 18
6/11/2008 12:22:24 PM
TV SETUP
TIME MENU
1. Press the MENU button.
2. Use the or button to select time, then press
the button to enter the time settings.
3. Use the or button to select the options
(OSD Duration, Sleep Timer, Time Zone or
Day Saving Time). Adjust them using the or
button.
4. Repeat step 3 to adjust other options.
5. To exit the MAIN MENU and return to the
normal screen, press the EXIT or MENU button
repeatedly.
OSD (On Screen Display) Duration : Select the length of time the On screen menu is displayed
: 15 Sec / 30 Sec / 45 Sec / 60 Sec.
Sleep Timer
: Select the length of time before the unit automatically changes to Standby
mode : Off -> 5 Minutes -> 10 Minutes -> 15 Minutes -> 30 Minutes ->
60 Minutes -> 90 Minutes -> 120 Minutes -> Off.
Time Zone
: Select the time zone from Eastern / Central / Mountain / Pacific / Alaska
/ Hawaii.
Day Saving Time : Select On to activate daylight savings time.
Clock
: Display the current time.
setup MENU
1. Press the MENU button.
2. Use the
or
button to select SETUP,
then press the button to enter the SETUP
settings.
3. Use the or button to select the options (OSD
Language, Color Mode, PC Set Up, Closed
Caption or Restore Setting). Adjust them using
the or button (The screen will change to
your desired setting); or press the button to
go into the detailed settings.
4. Press the MENU button to return to the previous
menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press the EXIT or MENU button
repeatedly.
OSD (On Screen Display) Language :Select On-screen menu language from English / French
/ Spanish.
Color Mode : Adjust the three color temperature of the picture. Choose from Normal
(balanced), Warm (red white), or Cool (blue white) modes.
Restore Setting
: If you reset the TV to the factory settings, all your present settings on
PICTURE and Audio will be erased and replaced by the factory’s default
settings.
E - 19
English P1-32.indd 19
6/11/2008 12:22:25 PM
TV SETUP
PC Set Up (in PC mode only)
- Resolution : 1,440 x 900 max
- Refresh Frequency : 60Hz max
H - Pos
V - Pos
Clock Phase
: Center the image by moving it left or
right.
: Center the image by moving it up or
down.
:Adjusts the display clock to change
width of the image.
:Adjusts the image if there is flicker of
screen letters, color misalignment, or
blurring.
Closed Caption
Note:
This function only works on
ATSC programs broadcast
with captions.
CC Mode
Analog Closed Caption
Digital Closed Caption
Digital Caption Style
: Select closed caption On, Off or CC on Mute.
: Select the analog closed caption or turn it off.
: Select the digital closed caption or turn it off.
: Select As Broadcaster to use the default digital caption style of the
broadcaster. Select Custom to activate the caption style items and
set your desired detailed settings.
Parental MENU
Password
1. Press the MENU button.
2. Use the or button to select PARENTAL,
then press the button to enter the PARENTAL
settings. The menu locked screen will be
displayed.
3. Enter a 4-digit password. Once entered, the
screen will enter the Parental menu. The preset
password is 0000.
If you forget the password,
enter “ 8888 “ to unlock parental control.
E - 20
English P1-32.indd 20
6/11/2008 12:22:26 PM
TV SETUP
Parental
1. Use the or button to select various Parental
settings. Adjust them using the or button,
or press the button to go into the detailed
settings.
2. Press the MENU button to return to the previous
menu.
3. Repeat steps 1 - 2 to adjust other options.
4. To exit the MAIN MENU and return to the
normal screen, press the EXIT or MENU button
repeatedly.
Rating Enable
US
Canada
RRT Setting
Reset RRT
U.S. TV
Ratings
: Select On to edit the following parental items. Select Off to disable parental
control.
: Set TV and MPAA ratings.
: Set Canada English and Canada French ratings.
: Set Rating Region Table.
: Reset Rating Region Table to the default settings.
TV-Y
TV-Y7
TV-G TV-PG TV-14 TV-MA
:Recommended for all children.
:Recommended for all children age 7 and above.
: General Audience.
: Parental Guidance Suggested.
: Parental Strongly Cautioned.
:Mature Audience Only.
N/A
G
PG U.S.
MPAA
Ratings
Canadian
English
Ratings
:Not rated.
: GENERAL AUDIENCES, Suitable for all ages.
: PARENTAL GUIDANCE SUGGESTED - Some material may not be
suitable for children.
PG-13 : PARENTS STRONGLY CAUTIONED - Some material may be
inappropriate for children under 13.
R
: RESTRICTED, Under 17 requires accompanying parent or adult
guardian for viewing in movie theaters.
NC-17 :No one 17 or under admitted in movie theaters,
X
: Adults Only.
E
C
C8+ G
PG
14+ 18+ Canadian
French
Ratings
:Exempt.
: Children.
: Recommended for children age 8 and older.
: GENERAL AUDIENCES, Suitable for all ages.
: PARENTAL GUIDANCE SUGGESTED - Some material may not be
suitable for children.
: Viewers 14 years and older.
: Adult Programming.
E
:Exempt.
G
: GENERAL AUDIENCES, Suitable for all ages.
8 ans+ : Not recommended for young children.
13 ans+ :Not suitable for children under the age of 13.
16 ans+ :Not suitable for children under the age of 16.
18 ans+ :Adult Programming.
E - 21
English P1-32.indd 21
6/11/2008 12:22:27 PM
TV SETUP
TV MENU (For TV Mode Only)
1. Press the MENU button.
2. Use the or button to select TV, then press
the button to enter the TV settings.
3. Use the or button to select the options
(Antenna, Auto Scan, Auto Scan Add CH,
Channel Skip, Channel No., Channel Label
or DTV Signal). Adjust them using the or
button, or press the button to go into the
detailed settings.
4. Press the MENU button to return to the previous
menu.
5. Repeat steps 3 and 4 to adjust other options.
6. To exit the MAIN MENU and return to the
normal screen, press the EXIT or MENU button repeatedly.
Antenna : Air (over-the-air broadcasts, Ch 2-69) or CATV (cable/satellite broadcasts,
CH 1-135) mode are available.
Auto Scan : Search for usable stations and store them in memory.
Auto Scan Add CH : Search for more usable stations and add them in memory. The stations
stored before are still kept.
Channel Skip : Skip weak channels and the channels you don’t like.
Channel No.
: Select a different TV channel.
Channel Label
: Display and edit the channel label.
DTV Signal
: Display the signal strength (for digital TV channels only).
Channel Skip
1. Use the or button to select a channel.
(Press the button to select the last channel
of the page; press again to go to the next page.
Press the button to select the first channel of
the page; press again to return the previous
page.)
2. Press the ENTER button to shift between On /
Off. (Select On to skip the selected channel.
The channel will not appear when you press
the CH
/ CH
button.)
Channel Label
You can edit a label for each channel.
1. Use the or button to select the number or
letter. Use the or button to move and edit
the next character. Press the ENTER button to
confirm.
2. After editing, the Channel and Channel Label
will be shown on the screen when you press
the DISPLAY button.
E - 22
English P1-32.indd 22
6/11/2008 12:22:28 PM
CD/DVD OPERATION
This owner’s manual explains the basic instructions of this unit. Some DVDs are produced to
limit operation during playback. For example, many DVDs do not allow users to skip government
warnings, or in some cases previews or other features. This is not a defect in the unit. Refer to the
instruction notes of discs.
” may appear on the screen during operation. A “
” means that the desired operation is
“
not permitted by the unit or disc.
Playing a Disc
1.Press the STANDBY/ON button to turn the unit on.
2.Press the FUNCTION button to select DVD mode.
See CUSTOMIZING THE DVD FUNCTION SETTINGS before proceeding to step 3.
3.Press the
PUSH OPEN button to open the disc door.
4.Hold the disc by its edge and gently push it onto the spindle, with the label side facing
the front, until you hear a “click”.
5.Push the disc door gently to close it. It takes a short while for your unit to load the
disc. After loading, for most DVDs, the unit will automatically take you main menu or
start playing. If the unit does not automatically start playing the DVD, press the PLAY
button.
PLAYING A PICTURE FILE DISC
This unit can play picture files recorded on CD-R and CD-RW discs.
1.Press the
PUSH OPEN button to open the disc door.
2.Hold the disc by its edge and gently push it onto the spindle, with the label side facing
the front, until you hear a “click”.
3.Push the door gently to close it. The picture files on the disc will be displayed one by
one automatically.
4.Press the STOP button to go to the folder list.
5.Press the or button to highlight a file to play. Press the PLAY button to start
playback.
Note:
• You can press the PAUSE button to interrupt playback, and press the PLAY button
to resume playback.
• You also can use the GOTO function or use the numbered buttons to enter the image
number to quickly select any image.
• Press the ANGLE button on the remote control to rotate the picture orientation by
90°.
Pausing playback (still mode)
Press the PAUSE button. To resume normal playback, press the PLAY button. Each time
you press the PAUSE button, the picture advances one frame.
Stopping playback
Press the STOP button at the location where you want to interrupt playback. To resume
playback at the position where the disc was stopped, press the PLAY button.
If you press the STOP button twice, the unit’s memory will be cleared and pressing the
PLAY button will reset the disc to the beginning.
SKIPPING TO A DIFFERENT TRACK
• Press the
PREV button to go back to previous chapters/tracks.
• Press the
NEXT button to advance chapters/tracks.
• For an Audio CD, use the number buttons (remote control only) to go directly to that
track number.
E - 23
English P1-32.indd 23
6/11/2008 12:22:28 PM
CD/DVD OPERATION
Fast Forward/Fast Reverse
1. Press the SEARCH
or
SEARCH button when a disc is playing.
•Each time the SEARCH
or
SEARCH button is pressed, the speed of fast scan
changes in the following sequence:
2. Press the PLAY button when you reach the desired point to resume playback at normal
speed.
SLOW-MOTION PLAY (dvd)
1.In Play mode, press the
SLOW button on the remote control. Each time the
SLOW button is pressed, the speed of slow-motion playback changes in the following
sequence:
2.Press the
PLAY button to return to normal playback speed.
Audio selection (DVD)
On some discs, the sound is recorded in two or more formats. Follow the directions below to
select the preferred language and sound system.
1.While a disc is playing, press the AUDIO
button to show the current audio format
number.
2.Press the AUDIO button repeatedly to select the desired audio format.
Note:
• If only one audio format is recorded, the number does not change.
• About two seconds later, playback continues in the new audio format.
Subtitle selection (DVD)
1.While a DVD is playing, press the SUBTITLE button to display the current language setting,
as shown in the example.
2.Press the SUBTITLE button repeatedly to select the desired
subtitle language.
Note:
• If only one language is recorded, the language does not change.
• About two seconds later, playback continues with the new subtitle selected.
• The number of languages recorded differs depending on the disc.
• This function can only be used for discs on which subtitles have been recorded in multiple
languages.
• On some DVDs, subtitles are activated from the main menu of the DVD. Press the DVD
MENU button to activate the main menu.
Angle selection (DVD)
Some DVDs contain scenes that have been shot from a number of different angles. For
these discs, the same scene can be viewed from each of these different angles.
1.While you are playing a DVD with different angles
recorded, press the ANGLE button to view the number
of current angles available.
Sequence of angle shots
2.Press the ANGLE button repeatedly to change the scene
(Example)
to the next angle in those recorded.
•About two seconds later, playback continues from
the new angle selected.
•If no button is pressed within 10 seconds, playback
continues without changing the current angle.
Note:
• This function can only be used for discs on which scenes shot from multiple angles have
been recorded.
• If only one angle is recorded, “ ” is displayed.
E - 24
English P1-32.indd 24
6/11/2008 12:22:29 PM
SPECIAL FUNCTIONS
DISPLAY function (DVD)
While the disc is playing, press the DISPLAY button repeatedly to display information on
operation status:
Locating a specific title (DVD)
If a DVD contains title numbers, you can locate a specific title by directly selecting a
title number.
1.In STOP mode, press the GOTO button.
2.Press the or button to highlight a specific field
and press the corresponding number button(s) for the title you want.
3.Press the ENTER button to confirm. Playback starts from the selected title.
Locating a specific chapter / track
If you know the chapter / track number you want to play, you can locate a specific chapter /
track by directly selecting a chapter / track number.
1.Press the GOTO button to search for your desired
chapter / track.
2.Press the or button to highlight a chapter / track then press the corresponding number
button(s) for the chapter /track you want.
3.Press the ENTER button to confirm. Playback starts from the selected chapter / track.
Locating a specific time
You can move to a specific location by entering its corresponding time (hours, minutes,
seconds)
1.Press the GOTO button twice.
2.Press the corresponding number buttons for the setting
point you want.
3.Press the ENTER button to confirm. Playback starts from the selected location.
Note:
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as specified.
• This method for accessing specific locations is available only within the current title of
the DVD.
E - 25
English P1-32.indd 25
6/11/2008 12:22:30 PM
REPEAT PLAYBACK
You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B
repeat)
Repeating a chapter (DVD)
You can play the same chapter repeatedly.
1.While the disc is playing, press the REPEAT button until the “
displays on the screen. The current chapter is played repeatedly.
” indicator
Repeating a title
You can play the same title repeatedly.
2.While the disc is playing, press the REPEAT button until the “
on the screen. The current title is played repeatedly.
To resume normal playback
3.While the disc is playing, press the REPEAT button until the “
on the screen.
” indicator displays
” indicator displays
You can play a single track or an entire disc repeatedly.
Repeating a single track (CD)
You can play the same track repeatedly.
1.While the disc is playing, press the REPEAT button until the “
on the screen. The current track is played repeatedly.
Repeating aN ENTIRE DISC
2.While the disc is playing, press the REPEAT button until the “
on the screen. The entire disc is played repeatedly.
” indicator displays
” indicator displays
To resume normal playback
3.Press the REPEAT button until the “
” indicator displays on the screen. Repeating a specific section (DVD) (CD)
You can play a specific section repeatedly.
1.While the disc is playing, press the A-B button at the beginning of the section (
is
displayed) you want to play repeatedly.
2.Press the A-B button again at the end of the section (
is displayed) you want to play
repeatedly.
3.The unit will immediately begin replaying your selection.
To resume normal playback
4.While the disc is playing, press the A-B button until the “
” indicator displays
on the screen.
Note:
• A-B repeat can only be used within the same title. If the start and end of the section to
be repeated are in different titles, A-B repeat is cancelled.
• The A-B repeat function does not operate in scenes where different camera angles are
recorded.
E - 26
English P1-32.indd 26
6/11/2008 12:22:31 PM
DVD PROGRAMMABLE PLAYBACK
Programmable memory
The two types of programmed playback provided by this unit is title/chapter programmed
playback.
Title/Chapter programmed playback
1.Press the MEMORY button in PLAY mode.
2.Input the title (2 digits) and chapter (2 digits) by pressing the number buttons. (For
example : 01 02, 02 05, 02 11) It will move to the next item automatically.
3.Repeat steps 2 to add additional titles and chapters.
4.Press the PLAY button to start the programmed playback.
CUSTOMIZING THE DVD FUNCTION SETTINGS
LANGUAGE SETUP
1.In STOP mode, press the SETUP button.
2.Use the or button to select the option (OSD
Language, Audio, Subtitle or Disc Menu), then
press the button.
3.Use the or button to select your preferred
language, then press the ENTER button to
confirm.
4.Press the button to go back to the previous menu.
Repeat steps 2 and 3 to adjust other options.
5.To exit the SETUP MENU and return to the normal screen, press the SETUP button.
Note:
• Some DVDs may not play in the audio language selected. A prior language may be
programmed on the disc.
• Some DVDs may be set to display subtitles in a language other than the one selected.
A prior subtitle language may be programmed on the disc.
• Some DVDs allow you to change subtitle selections via the disc menu only. If this is
the case, press the DVD MENU button and choose the appropriate subtitle from the
selection on the disc menu.
• Some DVDs may not included your pre-selected language. In this case, the DVD player
automatically displays disc menus consistent with the disc’s initial language setting.
E - 27
English P1-32.indd 27
6/11/2008 12:22:31 PM
CUSTOMIZING THE DVD FUNCTION SETTINGS
VIDEO SETUP
1.In STOP mode, press the SETUP button.
2.Press the or button repeatedly until VIDEO
SETUP appears.
3.Use the or button to select the option (Brightness
or Contrast), then press the button. Use the or
button to make adjustments, then press the ENTER
button. (The screen will change to your selected
setting).
4.Repeat steps 2 and 3 above to adjust other options.
5.To exit the SETUP MENU and return to the normal screen, press the SETUP button.
SYSTEM SETUP
1.In STOP mode, press the SETUP button.
2.Press the or button repeatedly until SYSTEM
SETUP appears.
3.Use the or button to select the option (Tv Display
or Default), then press the button. Use the or
button to make adjustments, then press the ENTER
button. (The screen will change to your selected
setting).
4.Repeat steps 2 and 3 above to adjust other options.
5.To exit the SETUP MENU and return to the normal screen, press the SETUP button.
TV type
Cut off when a wide-
screen video image is
Pan Scan
played.
• When wide-screen video is played, this mode clips the right and
left sides of the image so that it can be viewed on a conventional
screen.
• Some wide-screen DVDs that do not permit Pan Scan mode playback
are automatically played in letterbox mode (black bands that appear
at the top and bottom of the screen).
PAN SCAN
Letter Box
• When wide-screen video is played in this mode on a conventional
screen, black bands appear at the top and bottom of the screen.
Wide screen
• This is the correct mode for playing wide-screen videos on the unit
LETTER BOX
or other external wide-screens.
Note:
• The displayable picture size is preset on the DVD. Therefore the
playback picture of some DVDs may not conform to the picture
size you select.
WIDE SCREEN
• When you play DVDs recorded in the 4:3 aspect ratio, the playback
picture will always appears in the 4:3 aspect ratio regardless of the TV TYPE setting.
• If the screen mode is still not correct, press the LCD MODE button repeatedly to adjust
it.
Default
It takes 3-5 seconds to reset the DVD settings to the factory default.
E - 28
English P1-32.indd 28
6/11/2008 12:22:32 PM
MAINTENANCE
Cleaning THE Disc
A defective or soiled disc inserted into the
unit can cause sound to drop out during
playback.
Handle the disc by holding its inner and
outer edges.
• Do NOT touch the surface of the
unlabeled side of the disc.
• Do NOT stick paper or tape on the
surface.
• Do NOT expose
the disc to direct
sunlight or excessive
heat.
• Clean the disc before playback. Wipe
the disc from the center outward with a
cleaning cloth.
• NEVER use solvents such as benzine or
alcohol to clean the disc.
• Do NOT use irregular shaped discs
(example : heart shaped, octagonal, etc.).
They may cause malfunctions.
Cleaning the unit
• Be sure to turn the unit off and disconnect
the AC power cord before maintaining the
unit.
• Wipe the unit with a dry soft cloth. If the
surfaces are extremely dirty, wipe clean
with a cloth that has been dipped in a
weak soap-and-water solution and wrung
out thoroughly. Wipe with a dry cloth.
• Never use alcohol, benzine, thinner,
cleaning fluid or other chemicals. Do
NOT use compressed air to remove
dust.
Important Note
Before transporting the unit, remove the disc
from the disc compartment.
Trouble Shooting Guide
SYMPTOM
CAUSE (AND REMEDY)
No power.
• Ensure the AC power cord is connected.
• Turn on the unit.
The remote does not • Remove any obstacles between the remote and the unit.
function.
• Use the remote near the unit.
• Point the remote at the remote sensor on the unit.
DVD
• Replace the batteries in the remote with new ones.
No sound or only a • Make sure that you’ve selected DVD mode.
PLAY button to
very low-level sound • The system is in pause mode. Press the
return to normal play mode.
is heard.
• Fast forward or fast reverse is performed. Press the
PLAY
button to return to normal play mode.
• Make sure the AUDIO / VIDEO output and AV IN input
connections are correct.
• The DTS DVD cannot be decoded to have speaker output.
• This unit is too hot. Power off the unit for 30 minutes to cool
down.
No picture
• The region number of the disc doesn’t match the region
number of this unit.
E - 29
English P1-32.indd 29
6/11/2008 12:22:32 PM
Trouble Shooting Guide
The picture is not
clear
Severe hum or
noise is heard.
The disc does not
play.
TV
Bad Picture (snow,
multiple images,
distortion, blurry)
No sound.
Black and white
picture.
No picture or
sound.
Colored patches of
picture.
• Clean the disc.
• The disc is scratched.
• The plugs and jacks are dirty. Wipe them with a cloth slightly
moistened with alcohol.
• Clean the disc.
• There is no disc inside (“No Disc” appears on the screen).
• Insert the disc correctly with the playback side facing
frontward.
• Clean the disc.
• A non-NTSC disc has been inserted. The unit and disc region
number are incompatible.
• Condensation may have formed inside the unit due to a sudden
change in temperature. Wait about an hour for it to clear and
try again.
• Check the location of the antenna and adjust it if necessary.
• Make sure the antenna cable is firmly connected.
• Make sure all input cables are firmly connected.
• Increase the volume.
• Check whether the mute function has been activated on the
remote control. • Check the SET UP MENU setting within the TV SETUP
menu.
• Check to make sure the program you are watching is broadcast
in Color and not Black & White.
• Make sure the unit is plugged in and turned on.
• Make sure TV mode is selected.
• Try a new channel to check for possible station trouble.
• Make sure the antenna is connected properly.
• Increase the volume.
• Make sure the antenna or audio/video source device is
working properly.
• Make sure all cables are firmly connected.
• Check for local interference.
• Make sure there are no unshielded electrical devices nearby
that are causing interference.
• Turn the TV off for 30 minutes, then try it again.
E - 30
English P1-32.indd 30
6/11/2008 12:22:32 PM
Unit: INCH
E - 31
English P1-32.indd 31
6/11/2008 12:22:32 PM
E - 32
English P1-32.indd 32
Printed in china
811-319991W150
6/11/2008 12:22:32 PM