Sharp MX-5500N Specifications

mx7000_gb_saf.fm
-1 ページ
2006年4月19日 水曜日 午後3時28分
MODEL: MX-5500N
MX-6200N
MX-7000N
DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
Safety Guide
Before installing this product, be sure to read the
"CAUTIONS" and "INSTALLATION
REQUIREMENTS" sections.
CAUTIONS
INSTALLATION REQUIREMENTS
SUPPLIES
SPECIFICATIONS
INFORMATION ON DISPOSAL
TO THE ADMINISTRATOR OF THE MACHINE
Keep this manual close at hand for reference
whenever needed.
mx7000_gb_saf.fm
0 ページ
2006年4月19日 水曜日 午後3時28分
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Shielded network cable and USB cable must be used with this equipment to maintain compliance with standards.
➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢
Required in IEC-950 (EN 60 950) - Europe
• The equipment should be installed near an accessible socket outlet for easy disconnection.
Required in Appendix ZB of BS 7002 (En 60 950) — United Kingdom
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable
(moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse
and of the same rating as the one removed from the plug must
to BS1362 marked
or
be used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without
the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied
either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable
plug is fitted and fit an appropriate type observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately
and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted
elsewhere into a 13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW: Earth
BLUE:
Neutral
BROWN:
Live
As the colours of the wires in this mains lead may not correspond with coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND YELLOW must be connected to the terminal in the plug
which is marked with the letter E, or by the safety earth symbol Å@, or coloured green or greenand-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter
N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured red.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢
➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢
➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣
EMC (this machine and peripheral devices)
Warning:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
This machine contains the software having modules developed by Independent JPEG Group.
mx7000_gb_saf.fm
1 ページ
2006年4月20日 木曜日 午後7時8分
For the users of the fax function
FAX interface cable and Line cable:
These special accessories must be used with the device.
Notice for Users in Europe
This equipment complies with the requirements of Directive 1999/5/EC.
Dieses Gerät entspricht den Anforderungen der EU-Richtlinie 1999/5/EG.
Cet appareil est conforme aux exigences de la directive 1999/5/CE.
Este aparato satisface las exigencias de las Directiva 1999/5/CE.
Quest'apparecchio è conforme ai requisiti delle direttiva 1999/5/CE.
Dit apparaat voldoet aan de eisen van de richtlijn 1999/5/EG.
Este equipamento obedece às exigências da directiva 1999/5/CE.
Denna utrustning uppfyller kraven enligt direktiv 1999/5/EC.
Dette udstyr overholder kravene i direktiv 1999/5/EF.
Dette produktet oppfyller kravene i direktiv 1999/5/EC.
Tämä laite täyttää direktiivi 1999/5/EY.
This equipment has been designed to work on the British analogue public switched telephone network.
This equipment has been tested according to the pan-European TS103 021 regulation.
It will operate on all analogue telephone networks which comply with the TS103 021.
Please contact your dealer or network operator, if you are not sure whether your network operates according to
TS103 021.
The Declaration of Conformity can be viewed at the following URL address.
http://www.sharp.de/doc/MX-FXX1.pdf
1
mx7000_gb_saf.fm
2 ページ
2006年4月19日 水曜日 午後3時28分
Contents
CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Finisher specifications . . . . . . . . . . . . . . . . . . . . . 12
Laser information . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Saddle stitch finisher specifications . . . . . . . . . . . 13
INSTALLATION REQUIREMENTS . . . . . . . . . . . . . 5
Punch module specifications
(for finisher / saddle stitch finisher). . . . . . . . . . . . 14
SUPPLIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Inserter specifications. . . . . . . . . . . . . . . . . . . . . . 15
Storage of supplies. . . . . . . . . . . . . . . . . . . . . . . . . 6
Printer specifications . . . . . . . . . . . . . . . . . . . . . . 16
Supply of spare parts and consumables . . . . . . . . 6
Network scanner / Internet Fax specifications . . . 17
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Machine specifications / copier specifications . . . . 7
Pull scan function (TWAIN) specifications . . . . . . 17
Facsimile specifications . . . . . . . . . . . . . . . . . . . . 18
Continuous copying speeds . . . . . . . . . . . . . . . . . . 9
INFORMATION ON DISPOSAL . . . . . . . . . . . . . . . 19
Printable sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. Information on Disposal for Users (private
households) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Ambient environment . . . . . . . . . . . . . . . . . . . . . . . 9
Acoustic noise emission (measurement according to
ISO7779) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Emission concentration (measurement according to
RAL-UZ62: Edition Jan. 2002) . . . . . . . . . . . . . . . 10
Automatic document feeder specifications. . . . . . 10
Large capacity tray (MX-LCX2) specifications . . . 11
Large capacity tray (MX-LCX3) specifications . . . 11
B. Information on Disposal for Business Users. . . 19
TO THE ADMINISTRATOR OF THE MACHINE . . 22
Factory default passwords . . . . . . . . . . . . . . . . . . 22
Forwarding all transmitted and received data to the
administrator (document administration function). . . .22
For the users of the fax function . . . . . . . . . . . . . . . . .23
Trademark acknowledgments . . . . . . . . . . . . . . . 24
Note:
• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please
contact your dealer or nearest authorised service representative.
• This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is
discovered, please contact your dealer or nearest authorised service representative.
• Aside from instances provided for by law, SHARP is not responsible for failures occurring during the use of the product or its
options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due
to use of the product.
Products that have earned the ENERGY STAR® are designed to protect the environment
through superior energy efficiency.
Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no
warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not
responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
©Copyright SHARP Corporation 2006. All rights reserved. Reproduction, adaptation or translation without prior written permission is
prohibited, except as allowed under copyright laws.
2
mx7000_gb_saf.fm
3 ページ
2006年4月19日 水曜日 午後3時28分
CAUTIONS
1. Do not touch the transfer belt. Scratches or smudges on the transfer belt will
cause dirty prints.
2. The fusing unit is extremely hot. Exercise care in this area.
3. Do not look directly at the light source. Doing so may damage your eyes.
4. When the machine is installed, the adjusters (4) must be lowered to the floor
Fusing unit
to secure the machine (prevent it from moving).
Rotate the adjusters in the locking direction until they are in firm contact with
the floor.
If you find it necessary to reposition the machine due to rearrangement of
your office layout or other reason, retract the adjusters from the floor, turn off
the power, and then move the machine.
(After moving the machine, lower the adjusters again to secure the machine.)
5. Do not make any modifications to this machine. Doing so may result in
personal injury or damage to the machine.
6. The machine is heavy. To prevent injury when moving the machine, it is
recommended that it be moved by four or more persons.
7. Do not make copies of anything which is prohibited from copying by law. The
following items are normally prohibited from printing by national law. Other
items may be prohibited by local law.
● Money ● Stamps ● Bonds ● Stocks
Adjuster
● Bank drafts ● Checks ● Passports ● Driver's licences
8. Do not use a flammable spray to clean the machine. If gas from the spray
Lock
Release
comes in contact with hot electrical components or the fusing unit inside the
machine, fire or electrical shock may result.
9. Do not throw toner, a toner container (toner cartridge), or a waste toner box into a fire. Toner may fly and cause
burns.
10. Store toner, toner containers (toner cartridges), and waste toner boxes out of the reach of children.
The machine includes the document filing function, which stores document image data on the machine's hard drive. Stored
documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be possible to call
up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the
originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, Sharp Corporation bears no responsibility for any damages or loss due to the
loss of stored document data.
"BATTERY DISPOSAL"
THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF PROPERLY.
PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORISED SERVICE REPRESENTATIVE FOR ASSISTANCE IN
DISPOSING OF THIS BATTERY.
Each instruction also covers the optional units used with these products.
3
mx7000_gb_saf.fm
4 ページ
2006年4月19日 水曜日 午後3時28分
CAUTIONS
Laser information
Wave length
Colour: 785 nm
+10 nm
-15 nm
B/W: 788 nm
Pulse times
(North America and Europe)
Colour:
55/62/70 cpm model *1 (3.5 µs ±3.5 ns)/7 mm
55/62/70 cpm model (4.9 µs ±4.9 ns)/7 mm
+12 nm
-15 nm
B/W:
55/62/70 cpm model *1 (4.8 µs ±4.8 ns)/7 mm
55/62 cpm model (4.0 µs ±4.0 ns)/7 mm
70 cpm model (3.4 µs ±3.4 ns)/7 mm
*1: heavy paper
Output power
Max 0.8 mW
At the production line, the output power of the scanner unit is adjusted to 0.40 MILLIWATT PLUS 5% and is maintained constant by
the operation of the Automatic Power Control (APC).
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
For North America:
SAFETY PRECAUTIONS
This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that
the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges
or other items into switch slots.
For Europe:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION
CLASS 3B INVISIBLE LASER
RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
VORSICHT
UNSICHTBARE
LASERSTRAHLUNG DER
KLASSE 3B, WENN
ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM
STRAHL AUSSETZEN.
ADVARSEL
USYNLIG LASERSTRÅLNING
AF KLASSE 3B VED ÅBNING,
NÅR SIKKERHEDSBRYDERE
ER UDE AF FUNKTION. UNDGÅ
UDSÆTTELSE FOR
STRÅLNING.
ADVARSEL
USYNLIG KLASSE 3B
LASERSTRÅLNING NÅR
DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES .
UNNGÅ EKSPONERING FOR
STRÅLEN.
VARNING
OSYNLIG LASERSTRÅLNING
KLASS 3B NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRRAR ÄR
URKOPPLADE. UNDVIK
EXPONERING FÖR STRÅLEN.
VARO!
AVATTAESSA JA
SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTÖNTÄ
LUOKAN 3B LASERSÄTEILYLLE.
ÄLÄ KATSO SÄTEESEEN.
The above label is affixed to the laser
unit inside the machine.
4
mx7000_gb_saf.fm
5 ページ
2006年4月19日 水曜日 午後3時28分
INSTALLATION REQUIREMENTS
Improper installation may damage this product. Please note the following during initial installation and whenever the
machine is moved.
1. The machine should be installed near an accessible
power outlet for easy connection.
2. Be sure to connect the power cord only to a power
outlet that meets the specified voltage and current
requirements. Also make certain the outlet is properly
grounded.
• For the power supply requirements, see the name
plate in the lower corner of the left side of the
machine.
Connect the machine to a power outlet which is not
used for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
3. Do not install the machine in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity
changes, e.g., near an air conditioner or heater.
4. Be sure to allow the required space around the
machine for servicing and proper ventilation.
5. The machine includes a built-in hard drive. Do not
subject the machine to shock or vibration. In
particular, never move the machine while the power is
on.
30 cm
(11-13/16")
30 cm
(11-13/16")
45 cm
(17-23/32")
A small amount of ozone is produced within the printer during operation. The emission level is insufficient to cause any health
hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average
concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated
area.
5
mx7000_gb_saf.fm
6 ページ
2006年4月19日 水曜日 午後3時28分
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher
staple cartridge, and transparency film.
For best copying results, be sure to use only Sharp Genuine Supplies which are designed,
engineered, and tested to maximize the life and performance of Sharp products. Look for the
Genuine Supplies label on the toner package.
GENUINE SUPPLIES
Storage of supplies
Proper storage
1. Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds.
Storing toner cartridges
Store a new toner cartridge box horizontally. Do not store it standing on end. If stored standing on end, the toner may not
distribute well even after shaking the cartridge vigorously, and will remain inside the cartridge without flowing out.
Staple cartridge
The finisher and saddle stitch finisher require the following staple cartridge:
AR-SC2 (for finisher and saddle stitch finisher)
Approx. 5000 per cartridge x 3 cartridges
AR-SC3 (for saddle stitch finisher only)
Approx. 2000 per cartridge x 3 cartridges
Supply of spare parts and consumables
The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of
production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of
the product, whereas those parts which normally exceed the life of the product are not to be considered as spare parts.
Consumables too, are available for 7 years following the termination of production.
6
mx7000_gb_saf.fm
7 ページ
2006年5月17日 水曜日 午後4時0分
SPECIFICATIONS
Machine specifications / copier specifications
Name
Digital Full Colour Multifunctional System MX-5500N/6200N/7000N
Type
Console
Photoconductive type
OPC drum
Printing method
Electrophotographic system (laser)
Developer system
Dry-type two-component magnetic brush development
Fusing system
Heat rollers
Black and white scanning: 600 x 600 dpi, 600 x 300 dpi (factory default values)
Colour scanning:600 x 600 dpi (factory default values)
Document glass
Scanning resolution
Duplex single pass
feeder (automatic
document feeder)
Printing resolution
600 x 600 dpi
Scanning gradation
10 bits
Printing gradation
Black and white printing: 2 tones (1 bit)
Colour printing: 2 tones per colour (1 bit) or 16 tones per colour (4 bits)
Original sizes / types
Max. A3 (11" x 17") / sheets, bound documents
Copy sizes
Maximum: A3W (12" x 18") Minimum: A5R (5-1/4" x 5-3/4")
Print margins
Leading edge: 4 mm (11/64") or less, trailing edge: 4 mm (11/64") or less, near edge / far edge: total
4 mm (11/64") or less
Warm-up time
295 seconds or less (at room temperature of 23°C (73.4°F) and rated voltage)
First-copy time*
Colour copy time: 8.4 seconds
Black and white copy time: 4.0 seconds (MX-7000N)
4.5 seconds (MX-5500N/6200N)
(Portrait feeding of A4 (8-1/2" x 11") sheets from 2nd paper tray, without auto colour selection and
auto colour mode.)
Copy ratios
Variable: 25% to 400% in increments of 1%, total 376 increments (25% to 200% when the automatic
document feeder is used)
Fixed presets: 25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% and 400% for AB sizes;
25%, 50%, 64%, 77%, 100%, 121%, 129%, 200% and 400% for inch sizes.
Two reduction ratios and two enlargement ratios can be stored.
Continuous copy
999 copies
Automatic document
feeder
See "Automatic document feeder specifications".
Black and white scanning: 600 x 600 dpi, 600 x 300 dpi (factory default values)
Colour scanning:600 x 600 dpi (factory default values)
Tray 1
Paper sizes:
Paper weight:
Paper capacity:
Paper types:
A4, 8-1/2" x 11"
Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.))
1200 sheets (80 g/m2 (21 lbs.))
SHARP-recommended plain paper, recycled paper, and coloured paper
Tray 2
Paper sizes:
Paper weight:
Paper capacity:
Paper types:
A4, 8-1/2" x 11"
Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.))
800 sheets (80 g/m2 (21 lbs.))
SHARP-recommended plain paper, recycled paper, and coloured paper
* First copy out time is measured with original on the document glass in full ready condition with fuser at operating temperature and
mirror motor at operating speed in each of black and white mode and colour mode, actual time may vary based on environment
conditions.
7
mx7000_gb_saf.fm
8 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Machine specifications / copier specifications (Continued)
Paper sizes:
Tray 3
A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14",
8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K,
16K, 16KR (Includes automatic paper size detection function.)
Paper weight: Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)), heavy paper (106 g/m2 to
209 g/m2 (28 lbs. to 56 lbs.))
Paper capacity: 500 sheets (80 g/m2 (21 lbs.)), transparency films 40 sheets, heavy paper 80
sheets, tab paper 40 sheets, gloss paper 40 sheets
Paper types:
SHARP-recommended plain paper, recycled paper, coloured paper, heavy paper,
and transparency film
Paper sizes:
Tray 4
A3W, A3, B4, A4, A4R, B5, B5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 8K, 16K, 16KR (Includes automatic
paper size detection function.)
Paper weight: Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)), heavy paper (106 g/m2 to
209 g/m2 (28 lbs. to 56 lbs.))
Paper capacity: 500 sheets (80 g/m2 (21 lbs.))
Paper types:
SHARP-recommended plain paper, recycled paper, coloured paper, and heavy paper
Paper sizes: A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR (Includes automatic paper size
detection function. Entry of paper sizes up to 297 mm x 420 mm (11" x 17") is possible.)
Bypass tray
Paper weights:
Thin paper (55 g/m2 to 59 g/m2 (15 lbs. to 16 lbs.)), plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)),
heavy paper (106 g/m2 to 256 g/m2 (28 lbs. to 68 lbs.)), envelopes (75 g/m2 to 90 g/m2 (20 lbs. to 24 lbs.))
Paper capacity: Standard paper 100 sheets
Paper types:
Plain paper, recycled paper, coloured paper, heavy paper, thin paper, transparency film, envelopes
(Monarch, Com-10, DL, C5)
Duplex module
Paper sizes: A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight: Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)), heavy paper (106 g/m2 to
209 g/m2 (28 lbs. to 56 lbs.))
Paper types: SHARP-recommended plain paper, recycled paper, coloured paper, and heavy paper
Output method: Face-down output
Output capacity:
250 sheets (using SHARP-recommended A4 or 8-1/2" x 11" paper)
Output tray (Centre tray)*
(The maximum number of sheets that can be held varies depending on ambient conditions in the
installation location, the type of paper, and the storage conditions of the paper.)
Tray full sensor: Yes
Right tray
Output method: Face-down output
Output capacity:
100 sheets (using SHARP-recommended A4 or 8-1/2" x 11" paper)
(The maximum number of sheets that can be held varies depending on ambient conditions in the
installation location, the type of paper, and the storage conditions of the paper. Envelopes, heavy
paper (106 g/m2 to 209 g/m2 (28 lbs. to 56 lbs.)), and tab paper cannot be used.)
Tray full sensor: Yes
Required power supply
Local voltage ±10% (For the power supply requirements, see the name plate in the lower corner of
the left side of the machine.)
Power consumption
220-240V: 1.84 kW 100-127V: 1.80 kW
Dimensions
795 mm (W) x 715 mm (D) x 1225 mm (H) (31-19/64" (W) x 28-9/64" (D) x 48-7/32" (H))
Weight
Approx. 209 kg (460.8 lbs.)
Overall dimensions
1130 mm (W) x 715 mm (D) (44-31/64" (W) x 28-9/64" (D)) (when bypass tray is extended)
* Output tray (Centre tray) cannot be used when the finisher (MX-FNX3) or saddle stitch finisher (MX-FNX4) is installed.
8
mx7000_gb_saf.fm
9 ページ
2006年4月20日 木曜日 午前11時43分
SPECIFICATIONS
Continuous copying speeds*
Model
MX-5500N
MX-6200N
Copy ratio
MX-7000N
100% / Reduced / Enlarged
Black and
Colour copying
white copying
Copy mode
Colour copying
Black and
white copying
Colour copying
Black and
white copying
A3W, 12" x 18"
18 copies/min.
28 copies/min.
18 copies/min.
31 copies/min.
18 copies/min.
36 copies/min.
A3, 11" x 17", 8K
19 copies/min.
30 copies/min.
19 copies/min.
33 copies/min.
19 copies/min.
38 copies/min.
B4, 8-1/2" x 14",
8-1/2" x 13"
22 copies/min.
35 copies/min.
22 copies/min.
38 copies/min.
22 copies/min.
44 copies/min.
A4, B5, 8-1/2" x 11", 16K
41 copies/min.
55 copies/min.
41 copies/min.
62 copies/min.
41 copies/min.
70 copies/min.
A4R, B5R, A5R,
8-1/2" x 11"R,
7-1/4" x 10-1/2"R,
5-1/2" x 8-1/2"R, 16KR
26 copies/min.
40 copies/min.
26 copies/min.
44 copies/min.
26 copies/min.
51 copies/min.
* Copy speed during output of the second copy and following copies when performing continuous one-sided copying of the same
page (excluding offset output).
Printable sizes
Paper size
Ambient environment
Printable size
Paper size
Printable size
A3W*
297 x 420 mm
12" x 18"*
279 x 432 mm
A3
293 x 413 mm
11" x 17"
275 x 425 mm
B4
253 x 357 mm
8-1/2" x 14"
212 x 349 mm
A4
206 x 290 mm
8-1/2" x 13"
212 x 323 mm
B5
178 x 250 mm
8-1/2" x 11"
212 x 272 mm
A5
144 x 203 mm
5-1/2" x 8-1/2 "
136 x 209 mm
7-1/4" x 10-1/2R"
180 x 260 mm
8K
266 x 383 mm
16K
191 x 263 mm
* When printing on A3W (12" x 18") size paper using the PCL or PS printer driver,
the maximum print area is 299 mm x 450 mm.
(Humidity)
85%
60%
20%
10˚C
(54˚F)
30˚C 35˚C (Temperature)
(86˚F) (91˚F)
9
mx7000_gb_saf.fm
10 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Acoustic noise emission (measurement according to ISO7779)
Sound power level LwA
Printing mode
(continuous printing)
Colour: 6.8 B
Black and white: 7.3 B
Standby mode
5.5 B
Emission concentration (measurement according to RAL-UZ62: Edition Jan. 2002)
Ozone
0.02 mg/m3 or less
Dust
0.075 mg/m3 or less
Styrene
0.07 mg/m3 or less
Automatic document feeder specifications
Original sizes
A3 to A5, 11" x 17" to 5-1/2" x 8-1/2", long paper
(max. width 297 mm (11-45/64") x max. length 800 mm (31-31/64"), scanning in mono 2 mode of
one side only is possible in fax and image scan modes)
Original weight
One-sided 35 g/m2 to 128 g/m2 (9 lbs. to 34 lbs.) (Paper weights from 35 g/m2 (9 lbs.) to 49 g/m2
(13 lbs.) require the use of slow scan mode.)
Two-sided 50 g/m2 to 128 g/m2 (13 lbs. to 34 lbs.)
Capacity
150 sheets (80 g/m2 (21 lbs.)) Maximum stack height of 19.5 mm (3/4")
10
mx7000_gb_saf.fm
11 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Large capacity tray (MX-LCX2) specifications
Model
MX-LCX2
Paper sizes
A4, 8-1/2" x 11"
Paper weight
Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)), heavy paper (106 g/m2 to 209 g/m2 (28 lbs. to
56 lbs.))
Paper capacity
3500 sheets (80 g/m2 (21 lbs.))
Paper types
SHARP-recommended plain paper, recycled paper, coloured paper, and heavy paper
Power supply
Supplied from the machine
Dimensions
370 mm (W) x 550 mm (D) x 525 mm (H) (14-9/16" (W) x 21-21/32" (D) x 20-43/64" (H))
Weight
Approx. 28 kg (61.7 lbs.)
Overall dimensions when 1165 mm (W) x 715 mm (D) (45-55/64" (W) x 28-9/64" (D))
attached to machine
Large capacity tray (MX-LCX3) specifications
Model
MX-LCX3
Paper sizes
A3W, A3, B4, A4, A4R, B5, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11" 8-1/2" x 11"R
Paper weight
Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)), heavy paper (106 g/m2 to 209 g/m2 (28 lbs. to
56 lbs.))
Paper capacity
3000 sheets (80 g/m2 (21 lbs.))
Paper types
SHARP-recommended plain paper, recycled paper, coloured paper and heavy paper
Power supply
Supplied from the machine
Dimensions
670 mm (W) x 570 mm (D) x 525 mm (H) (26-3/8" (W) x 22-7/16" (D) x 20-43/64" (H))
Weight
Approx. 50 kg (110.2 lbs.)
Overall dimensions when 1465 mm (W) x 715 mm (D) (57-21/32" (W) x 28-9/64" (D))
attached to machine
11
mx7000_gb_saf.fm
12 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Finisher specifications*1
Model
MX-FNX3
Paper sizes
A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight
Thin paper (55 g/m2 to 59 g/m2 (15 lbs. to 16 lbs.)) plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.))
heavy paper (106 g/m2 to 256 g/m2 (28 lbs. to 68 lbs.)), envelopes (75 g/m2 to 90 g/m2 (20 lbs. to
24 lbs.))
Modes
Non-staple, staple
Allowed paper sizes for
offset
A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K
Offset distance
30 mm (1-3/16")
Upper tray
Non-stapling*3:
1550 sheets (A4, B5, A5R, 8-1/2" x 11",
5-1/2" x 8-1/2"R, 16K)
650 sheets (A3W, A3, B4, A4R, B5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (A4, B5, 8-1/2" x 11",
16K)
50 sets or 650 sheets (A3, B4, A4R, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
Lower tray
Non-stapling*3:
2450 sheets (A4, B5, 8-1/2" x 11", 16K)
1700 sheets (A5R, 5-1/2" x 8-1/2"R)
650 sheets (A3W, A3, B4, A4R, B5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2", 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (A4, B5, 8-1/2" x 11",
16K)
50 sets or 650 sheets (A3, B4, A4R, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
Tray
capacity*2
Power supply
Supplied from the machine
Dimensions
515 mm (W) x 645 mm (D) x 1100 mm (H) (20-9/32" (W) x 25-25/64" (D) x 43-19/64" (H))
Weight
Approx. 43 kg (94.8 lbs.)
Overall dimensions when 1775 mm (W) x 715 mm (D) (69-55/64" (W) x 28-9/64" (D)) (When tray is extended)
attached to machine
Stapler section
Allowed paper sizes for
stapling
A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two
staples.)
Maximum number of
sheets for stapling*4
50 sheets (A4, B5, 8-1/2" x 11", 16K)
30 sheets (A3, B4, A4R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
(30 sheets when the sheets are the same width but different lengths.)
*1 Paper pass unit (MX-PBX2) is required to connect the finisher to the machine.
*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of
paper, and the storage conditions of the paper.
*3 Up to 100 sheets of non-standard size paper, envelopes, and transparency film (A4 (8-1/2" x 11")) can be loaded.
*4 The maximum number of sheets for stapling assumes a paper weight of 80 g/m2 (21 lbs.) and includes two cover sheets of
106 g/m2 to 256 g/m2 (28 lbs. to 68 lbs.).
12
mx7000_gb_saf.fm
13 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Saddle stitch finisher specifications*1
Model
MX-FNX4
Paper sizes
A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight
Thin paper (55 g/m2 to 59 g/m2 (15 lbs. to 16 lbs.)), plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.)),
heavy paper (106 g/m2 to 256 g/m2 (28 lbs. to 68 lbs.)), envelopes (75 g/m2 to 90 g/m2 (20 lbs. to 24 lbs.))
Modes
Non-staple, staple, saddle stitch
Allowed paper sizes for offset A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K
Offset distance
30 mm (1-3/16")
Upper tray
Non-stapling*3:
1550 sheets (A4, B5, A5R, 8-1/2" x 11",
5-1/2" x 8-1/2"R, 16K)
650 sheets (A3W, A3, B4, A4R, B5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2", 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (A4, B5, 8-1/2" x 11",
16K)
50 sets or 650 sheets (A3, B4, A4R, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
Lower tray
Non-stapling*3:
2450 sheets (A4, B5, 8-1/2" x 11", 16K)
1700 sheets (A5R, 5-1/2" x 8-1/2"R)
650 sheets (A3W, A3, B4, A4R, B5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2", 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (A4, B5, 8-1/2" x 11",
16K)
50 sets or 650 sheets (A3, B4, A4R, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
Tray
capacity*2
Power supply
Supplied from the machine
Dimensions
625 mm (W) x 645 mm (D) x 1100 mm (H) (24-39/64" (W) x 25-25/64" (D) x 43-19/64" (H))
Weigh
Approx. 74 kg (163.1 lbs.)
Overall dimensions when 1885 mm (W) x 715 mm (D) (74-3/16" (W) x 28-9/64" (D)) (When tray is extended)
attached to machine
Stapler section
Allowed paper sizes for
stapling
A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two staples.)
Maximum number of
sheets for stapling*4
50 sheets (A4, B5, 8-1/2" x 11", 16K)
30 sheets (A3, B4, A4R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R, 8K)
(30 sheets when the sheets are the same width but different lengths.)
Saddle stitch section
Stapling method
Fold in half and staple in two places on centreline
Folding position
Fold at centreline (can be adjusted with [Saddle Stitch Position Adjust] in the System Settings)
Allowed paper sizes for
saddle stitch stapling
A3, B4, A4R, 11" x 17", 8-1/2" x 14", 8-1/2" x 11"R, 8K
Allowed paper weights for 55 g/m2 to 256 g/m2 (15 lbs. to 68 lbs.)
saddle stitch stapling
Maximum: 15 sheets (80 g/m2 (21 lbs.) x 14 sheets + 256 g/m2 (68 lbs.) x 1 sheet) / 10 sets (11 to
Number sheets for saddle
stitch stapling / Number of sets 15 sheets), 20 sets (6 to 10 sheets), 25 sets (1 to 5 sheets)
*1 Paper pass unit (MX-PBX2) is required to connect the saddle stitch finisher to the machine.
*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of
paper, and the storage conditions of the paper.
*3 Up to 100 sheets of non-standard size paper, envelopes, and transparency film (A4 (8-1/2" x 11")) can be loaded.
*4 The maximum number of sheets for stapling assumes a paper weight of 80 g/m2 (21 lbs.) and includes two cover sheets of
106 g/m2 to 256 g/m2 (28 lbs. to 68 lbs.).
13
mx7000_gb_saf.fm
14 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Punch module specifications (for finisher / saddle stitch finisher)
Model
MX-PNX2A
MX-PNX2B
MX-PNX2C
MX-PNX2D
Hole punching
2 holes
2 holes or 3 holes
4 holes
4 holes, broad width
2 holes:
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11"R
3 holes:
A3, A4, 11" x 17",
8-1/2" x 11"
A3, A4, 11" x 17",
8-1/2" x 11"
A3, A4, 11" x 17",
8-1/2" x 11"
Allowed paper sizes for
punching
A3, B4, A4, A4R, B5,
B5R, 11" x 17",
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11",
8-1/2" x 11"R,
7-1/4" x 10-1/2", 8K,
16K, 16KR
Punchable paper weights 55 g/m2 to 256 g/m2 (15 lbs. to 68 lbs.)
Power supply
Supplied from finisher / saddle stitch finisher
Dimensions
115 mm (W) x 600 mm (D) x 995 mm (H) (4-17/32" (W) x 23-5/8" (D) x 39-11/64" (H))
Weight
Approx. 8 kg (17.6 lbs.)
Note:
Special media such as transparency film and label sheets cannot be stapled or punched.
14
mx7000_gb_saf.fm
15 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Inserter specifications*
Model
MX-CFX1
Paper sizes
A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight
Thin paper (55 g/m2 to 59 g/m2 (15 lbs. to 16 lbs.)), plain paper (60 g/m2 to 105 g/m2 (16 lbs. to
28 lbs.)), heavy paper (106 g/m2 to 256 g/m2 (28 lbs. to 68 lbs.))
Paper capacity
100 sheets (80 g/m2 (21 lbs.))
Paper types
SHARP-recommended plain paper, recycled paper, coloured paper, heavy paper, thin paper, and
transparency film
Power supply
Supplied from finisher / saddle stitch finisher
Dimensions
455 mm (W) x 595 mm (D) x 1050 mm (H) (17-59/64" (W) x 23-27/64" (D) x 41-21/64" (H))
Weight
Approx. 23 kg (50.7 lbs.)
* Punch module (MX-PNX2A) is required to connect the inserter to the finisher (MX-FNX3).
15
mx7000_gb_saf.fm
16 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Printer specifications
Type
Built-in
Continuous printing speed
Same as continuous copying speed (When printing same document continuously on A4
(8-1/2" x 11") plain paper in non-offset mode, excluding processing time.)
Printing resolution
600 x 600 dpi / 1200 x 600 dpi*1 (black and white printing, rotating output not performed)
Printer driver type
PCL5c, PCL6, PostScript 3 compatible*1
Supported protocols
TCP/IP, IPX/SPX, NetBEUI, EtherTalk
Supported client PC
operating systems
See "VERIFYING SYSTEM REQUIREMENTS" in the Software Setup Guide.
Fonts
PCL5c, PCL6
80 European fonts, 28 barcode fonts*2, 1 bitmap font
PostScript 3 compatible*1
136 European fonts
Interface port
LAN connectivity: 10Base-T / 100Base-TX
USB (type A): Supports USB 2.0 (Full speed)
USB (type B): Supports USB 2.0 (Hi speed)*3
Memory
896 MB
Print area
Entire page excluding margin of 4.2 mm (11/64") at each edge. The actual print area may vary
depending on the printer driver and the software application.
*1 When the PS3 expansion kit (MX-PKX1) is installed and the machine is used as a PostScript printer.
*2 Barcode font kit (AR-PF1) is required.
*3 Supported operating systems are Windows 2000 / XP.
16
mx7000_gb_saf.fm
17 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Network scanner / Internet Fax*1 specifications
Type
Built-in
100 x 100, 200 x 200, 300 x 300, 400 x 400, 600 x 600
Scanning resolution (dpi) Internet Fax: 200 x 100, 200 x 200, 200 x 400, 400 x 400, 600 x 600 (200 x 100, 200 x 200 when file
type is TIFF-S) Halftone can be selected for resolutions other than 200 x 100 dpi.
Scanning speed
Colour (A4 / 8-1/2" x 11")One-sided: 35 pages/min. (200 x 200 dpi),
Two-sided: 35 pages/min. (200 x 200 dpi)
Black and white (A4 / 8-1/2" x 11") One-sided: 65 pages/min. (200 x 200 dpi),
Two-sided: 65 pages/min. (200 x 200 dpi)
Interface port
LAN connectivity: 10Base-T / 100Base-TX
Supported protocols
TCP/IP
Supported client PC
operating systems
Windows 98 / Me / NT 4.0 / 2000 / XP / Server 2003
File formats
Remarks
Colour
(including greyscale)
File types: TIFF, JPEG, PDF, Encrypted PDF
Compression ratio: High / Medium / Low
Black and white
File types: TIFF, PDF, Encrypted PDF
Compression modes: None / Medium (G3) / High (G4)
Internet Fax
(black and white only)
File types: TIFF-FX (TIFF-F, TIFF-S)
Compression modes: Medium (G3) / High (G4)
Number of one-touch keys for
storing destinations*2
Maximum number of keys: 999
Number of destinations that can be Maximum number of destinations in one group (1 key): 500
stored in a group (1 key)*2
Scan destinations
Scan to E-mail / Scan to FTP / Scan to Desktop / Scan to
Network Folder
*1 Internet fax expansion kit (MX-FWX1) is required.
*2 Total number of all destinations (Scan to E-mail, Scan to FTP, Scan to Desktop, Scan to Network folder, Internet Fax, Fax, and
Group)
*3 Supported operating systems vary depending on the transmission method. For Scan to Desktop, Windows 98 Second Edition / Me
/ 2000 Professional / XP Professional / XP Home Edition are supported. For Scan to Network Folder, Windows 98 / Me / NT 4.0 /
2000 Professional / XP Professional / XP Home Edition / 2000 Server / Server 2003 are supported.
Pull scan function (TWAIN) specifications
Supported protocol
TCP/IP
Supported client PC
operating systems
Windows 98 / Me / 2000 / XP / Server 2003
Colour modes
Full Colour, Greyscale, Mono Diffusion, Mono 2 gradation
Resolution settings
75 dpi, 100 dpi, 150 dpi, 200 dpi, 300 dpi, 400 dpi, 600 dpi
(The resolution can be specified by entering a numerical value from 50 to 9600 dpi. However, when
a high resolution is specified, it is necessary to reduce the scanning area.)
Scanning area
Maximum: A3 (11" x 17")
17
mx7000_gb_saf.fm
18 ページ
2006年4月19日 水曜日 午後3時28分
SPECIFICATIONS
Facsimile specifications
Model
MX-FXX1
Applicable telephone line Public switched telephone network, PBX
Scanning resolution
(supports ITU-T
standards)
8 x 3.85 lines/mm (Standard), 8 x 7.7 lines/mm (Fine, Fine-Halftone), 8 x 15.4 lines/mm (Super Fine,
Super Fine - Halftone), 16 x 15.4 lines/mm (Ultra Fine, Ultra Fine - Halftone)
Transmission speed
33.6 kbps down to 2.4 kbps Automatic fallback
Compression method
MH / MR / MMR / JBIG
Transmission modes
Super G3, G3 (the machine can only send faxes to and receive faxes from machines that support G3
or Super G3)
Input document size
AB sizes: A3, B4, A4, A4R, 8-1/2" x 11", 8-1/2" x 11"R, B5, B5R, A5
Inch sizes: 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, A4, A4R, 5-1/2" x 8-1/2"
Long originals (max. width 297 mm (11-45/64") x max. length 800 mm (31-31/64") can be transmitted
using the automatic document feeder. Scanning one side is possible.)
Paper sizes
A3, B4, A4, A4R, B5, B5R, A5R (11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
5-1/2" x 8-1/2"R)
Transmission time *1
Approx. 2 seconds (Super G3 mode/33.6 kbps, JBIG)
Approx. 6 seconds (G3 ECM mode/14.4 kbps)
Power supply
Supplied from the machine
Dimensions
285 mm (W) x 66 mm (D) x 213 mm (H) (11-7/32" (W) x 2-39/64" (D) x 8-25/64" (H))
Weight
Approx. 1.6 kg (3.5 lbs.)
Extension telephone connection
Possible (1 telephone)
Number of one-touch keys for storing
destinations*2
Maximum number of keys: 999
Number of destinations that can be stored in a Maximum number of destinations in one group
group (1 key)*2
(1 key): 500
Remarks
Timer transmission
Yes
Program function
Yes (48 programs)
F-code transmission
Supported (SUB/SEP (sub-address) and SID/PWD
(passcode) signals can be transmitted / received)
Image memory
8 MB standard
*1 Transmission speed is for an A4 or 8-1/2" x 11" document with approximately 700 characters at standard resolution (8 x 3.85
lines/mm) sent in high speed mode (33.6 kbps (JBIG) or 14.4 kbps). This is only the time required to transmit the image
information; the time required to send protocol signals is not included. Actual transmission times will vary depending on the
contents of the document, the receiving machine type, and telephone line conditions.
*2 Total number of all destinations (Scan to E-mail, Scan to FTP, Scan to Desktop, Scan to Network folder, Internet Fax, Fax and
Group)
18
mx7000_gb_saf.fm
19 ページ
2006年4月19日 水曜日 午後3時28分
INFORMATION ON DISPOSAL
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the
ordinary dust bin!
Used electrical and electronic equipment must be treated separately and in
accordance with legislation that requires proper treatment, recovery and
recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the
EU states may return their used electrical and electronic equipment to
designated collection facilities free of charge*. In some countries* your local
retailer may also take back your old product free of charge if you purchase a
similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators,
please dispose of these separately beforehand according to local
requirements.
By disposing of this product correctly you will help ensure that the waste
undergoes the necessary treatment, recovery and recycling and thus prevent
potential negative effects on the environment and human health which could
otherwise arise due to inappropriate waste handling.
Attention: Your product is
marked with this symbol. It
means that used electrical
and electronic products
should not be mixed with
general household waste.
There is a separate
collection system for these
products.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don't
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users.
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the
costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local
collection facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
19
mx7000_gb_saf.fm
20 ページ
2006年4月19日 水曜日 午後3時28分
mx7000_gb_saf.fm
21 ページ
2006年4月19日 水曜日 午後3時28分
✂
Administrator
Name:
Contact at:
Information that the administrator of the machine requires is printed on
the back of this page.
(Separate this page from the manual and keep it in a safe place. In
addition, fill in the name of the administrator and the administrator's
contact information in the left hand margin.)
21
mx7000_gb_saf.fm
22 ページ
2006年4月19日 水曜日 午後3時28分
TO THE ADMINISTRATOR OF THE
MACHINE
(Separate this page from the manual and keep it in a safe place.)
Factory default passwords
When accessing the system settings, the administrator password is required to log in with administrator
rights. The system settings can be configured in the Web pages as well as on the operation panel. To
access the system settings using the Web pages, a password is also required.
Factory default administrator password
Factory default setting: admin
Store a new administrator password as soon as the machine is installed.
Once the administrator password has been changed, the new password is required to restore the factory
default password. Take care to remember the new password.
There are two factory default accounts: "Administrator" and "User". A person who logs in as an
"Administrator" can configure all settings in the Web pages. A person who logs in as a "User" can only
configure certain settings.
The factory default passwords are shown below.
Factory default account
Factory default password
User
users
users
Administrator
admin
admin
Forwarding all transmitted and received data to the administrator
(document administration function)
This function is used to forward all data transmitted and received by the machine to a specified destination
(Scan to E-mail address, Scan to FTP destination, Scan to Network Folder destination, or Scan to Desktop
destination).
This function can be used by the administrator of the machine to archive all transmitted and received data.
To configure the document administration settings, click [Application Settings] and then [Document
Administration Function] in the Web page menu. (Administrator rights are required.)
Note:
• The format, exposure, and resolution settings of transmitted and received data remain in effect when the data is
forwarded.
• The functions below cannot be used when transmitted faxes are forwarded. In this case, the [Memory TX] key and
[Direct TX] key do not appear.
Quick Online transmission, direct transmission, dialling using the speaker
22
✂
Factory default passwords (Web pages)
mx7000_gb_saf.fm
23 ページ
2006年4月19日 水曜日 午後3時28分
TO THE ADMINISTRATOR OF THE MACHINE
For the users of the fax function
Important safety information
• If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may
cause harm to the telephone network.
• The AC power outlet shall be installed near the equipment and shall be easily accessible.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from
lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
• Do not install or use the machine near water, or when you are wet. Take care not to spill any liquids on the machine.
23
mx7000_gb_saf.fm
24 ページ
2006年4月19日 水曜日 午後3時28分
TO THE ADMINISTRATOR OF THE MACHINE
Trademark acknowledgments
The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and
accessories.
• Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows® Server
2003 and Internet Explorer® are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries.
• PostScript is a registered trademark of Adobe Systems Incorporated.
• Macintosh, Mac OS, AppleTalk, EtherTalk, LaserWriter, and Safari are registered trademarks or trademarks of Apple Computer, Inc.
• Netscape Navigator is a trademark of Netscape Communications Corporation.
• Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and other countries.
• PCL is a registered trademark of the Hewlett-Packard Company.
• IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.
• Sharpdesk is a trademark of Sharp Corporation.
• All other trademarks and copyrights are the property of their respective owners.
Candid and Taffy are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may
be registered in certain jurisdictions. CG Omega, CG Times, Garamond Antiqua, Garamond Halbfett, Garamond Kursiv,
Garamond and Halbfett Kursiv are trademarks of Monotype Imaging, Inc. and may be registered in certain jurisdictions. Albertus,
Arial, Coronet, Gill Sans, Joanna and Times New Roman are trademarks of The Monotype Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Avant Garde, ITC Bookman, Lubalin Graph,
Mona Lisa, Zapf Chancery and Zapf Dingbats are trademarks of International Typeface Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Clarendon, Eurostile, Helvetica, Optima,
Palatino, Stempel Garamond, Times and Univers are trademarks of Heidelberger Druckmaschinen AG, which may be registered
in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger
Druckmaschinen AG. Apple Chancery, Chicago, Geneva, Monaco and New York are trademarks of Apple Computer Inc. and may
be registered in certain jurisdictions. HGGothicB, HGMinchoL, HGPGothicB and HGPMinchoL are trademarks of Ricoh
Company, Ltd. and may be registered in some jurisdictions. Wingdings is a registered trademark of Microsoft Corporation in the
United States and other countries. Marigold and Oxford are trademarks of Arthur Baker and may be registered in some
jurisdictions. Antique Olive is a trademark of Marcel Olive and may be registered in certain jurisdictions. Hoefler Text is a
trademark of Johnathan Hoefler and may be registered in some jurisdictions. ITC is a trademark of International Typeface
Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions. Agfa is a
trademark of the Agfa-Gevaert Group and may be registered in certain jurisdictions. Intellifont, MicroType and UFST are
trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may be registered in
certain jurisdictions. Macintosh and TrueType are trademarks of Apple Computer Inc. registered in the United States Patent and
Trademark Office and other countries. PostScript is a trademark of Adobe Systems Incorporated and may be registered in some
jurisdictions. HP, PCL, FontSmart and LaserJet are trademarks of Hewlett-Packard Company and may be registered in some
jurisdictions. The Type 1 processor resident in Monotype Imaging's UFST product is under license from Electronics For Imaging,
Inc. All other trademarks are the property of their respective owners.
24
mx7000_gb_saf.fm
25 ページ
2006年4月19日 水曜日 午後3時28分
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
mx7000_gb_saf.fm
26 ページ
2006年5月17日 水曜日 午後4時4分
Safety Guide
This manual has been printed using a vegetable-based soy oil ink
to help protect the environment.
Printed on 100% post-consumer recycled paper
MODEL: MX-5500N
MX-6200N
MX-7000N
PRINTED IN CHINA
2006E
KS2
TINSE3394FCZZ