advertisement
VIEW SIZE THE WORLD
–
NOTE
For full installation,configuration,and operation details,refer to the
VSP1314 user manual,which is available at www.rgblink.com.
This guide provides quick start instructions for an experienced installer to set up and operate the VSP1314.
Installation and cabling features
Rear Panel
Re fer the an
to
co d i be pro
w mp ns for du ww let tal e c lat on ct bli nk.
.rg
se ion ne to r m
in cti the ng
po cn
fo an ua cti
th e we r l on r s ou rce
.
Connections
1 USB Input Port 14 24 Power supply port of sending card
2 ~ 5 CVBS Input Port BNC 15 25 Send Card USB Control Port
6 7
8
9
VGA Input Port DB-15
Mini switches
16 26
17 ~ 19
DVI Input Port to Processor DVI Output。
DVI Input Port DVI-I
20 DVI Input Port DVI-I RJ-45 Port
10 USB Control Port 21 DVI+VGA Output Port DVI-I
11
12 13
RS232 Control Port
27 28 Power Port IEC-3
22 23 10/100M Internet Control Port ,Connect to
LED Screen via cable
Step 1-Mounting
Turn off or disconnect all equipment power sources.
Step7-Program(DVI1)Output Port
DVI Used to connect with DVI-based display or LED control display.
Step 2-CVBS Input Port BNC
Used to input composite signal ,including
(PAL,NTSC and SECAM)。
Step8-Preview(DVI2+VGA) Output Port
Used to connect with DVI-base monitor so as to monitor the status of input signal, or connect to VGA-base monitor via a VGA cable.
Step 3-VGA Input Port DB15
VGA Input used to connect signal from
VGA and DVD Player ,Compatible with YPBPR.
Step 4-DVI1/2 Input Port DVI-I
DVI1/2 Input port support signal source of HDMI from HD player or DVI from
PC.
Step5-DVI3 Input Port
DVI to DVI/VGA splitter cable:One end is DVI-I or
DVI-D male, the other end is
DVI-I or DVI-D female together with VGA male.
DVI to VGA Adapter,it has DVI-I male at one end and VGA male at the other end.
DVI3 Input port support signal source of
PC;User can receive DVI signal via DVI
cable for background image or split image.
Step6-USB Input Port
USB Used to connect with USB or mobile
HDD.
Step9-LAN(Ethernet)Port
Use twist CAT5 cable to connect to LAN port .Default
IP address: 192.168.0.100. Operator can also change the IP address by RS 232 or USB.Twist CAT5 should be one end in T568A, and another end in T568B standard.
Address:Rm.S603-604,Weiye Building ,Torch Hi-Tech Industrial Development Zone,Xiamen,
Tel: 00865925771197 Fax:00865925771202
Email: [email protected] http://www.rgblink.cn
VSP 1314 Quick Start
Version1.0
Page 1 of 3
Pins
1
2
3
4
5
Crossover Cable
Pin T568A Wire color T568B Wire color
White-green
Green
White-orange
Blue
White-blue
White-orange
Orange
White-green
Blue
White-blue
CAT5 is crosswire standardized with T568A for one end and T568B for the other.
VSP 1314 support 9 kinds of output resolutions
NOTE as following:
1024×768×60Hz,1280×768×60Hz,1280×720×60Hz,
1280×1024×60Hz,1366×768×60Hz,1400×1050×60Hz,
1440×900×60Hz ,1680×1050×60Hz, 1920×1080×60Hz
Output resolution should be the same or bigger than
Insert Twisted
Pair Wires RJ-
45 Connector
6
7
White-orange
White-brown
Green
White-brown display system resolution.
8 Brown
T568A
Brown
T568B
Step10-USB Port
USB cable Used to connect the VSP 1314 and green light means the upper function, the red light means the lower function, no light means the function is at the computer.
ready state. Such as press Menu/Effect , firstly the green light on and it is the Menu Functional
Step11-Serial Port
Use RS232-to-RJ11 cable to connect a control system state, press again and go into Effect functional state with red light on, press again, light out. And return to the
or computer to the back panel RJ11port and the other end on RS232 port . Below is the definition for RS232to-RJ11 cable.
Pin RS-232 Function RS-422 Function homepage.
Step 2 Input switch
VSP 1314 supports 4 composite inputs, 2个USB inputs, 2
2
3
5
TX
RX
Transmit
Receive
GND Signal Ground
TX-
RX-
GND
Transmit(-)
Receive(-)
Signal
Insert Twisted Pair
Wires RS232/RS422
Connector
7
8
---
---
Not Used
Not Used
RX+
TX+ Transmit(+)
1314 supports 3 layer display. Layer 1 includes: The signal source of CV1, CV2, USB1, DVI1, VGA1. Layer 2 includes: The signal source of CV3,CV4,USB2,DVI2,
Pin
1
RJ-11
---
Function
Not Used
VGA2. Layer 3 is the background input, User can select the background signal as DVI3 or the BLACK
2
3
RX
TX
Receive
Transmit
4 GND Signal Ground Insert Twisted
Pair Wires
RJ11 connector
Step 12-Power Port
VSP 1314 use signal power plug and pull for power background.
Signal source key light instructions::
NOTE
VSP 1314 Use the traffic light passing control principle, The green light means in showing: Program shows the image which green light refers; The yellow up, connect IEC port power line and VSP 1314 power light means to be broadcast; Preview shows the image which the yellow light refers. The red light means to start, and it support AC power from 85 to
265V ,which means world wide compatible.
Step 13-Power on
After power , LCD module on the front panel will show ready for play, which means that the Preview signal can be chose; No light means the user cannot work on the programming.
RGBlink and its LOGO, as well as the following information: AVDSP series VSP 1314, cascadable 3 layers seamless switcher and mosaic scaler. Then come
DVI inputs (compatible HDMI1.3), 2 VGA inputs(compatible YPBPR), 1 background input (DVI
1.0) , input signal via the corresponding interface. VSP
Default layer 1 is the Program output signal source of
DVI1 ,now the DVI backlight turns green, if signal keys of the same layer are light off, they cannot be into work menu homepage, and auto refresh LCD module menu display statue every two minutes and selected; If users need to change the input signal of
Program, choose signal keys of any other layers. DVI2, display default input signals information and format, output format. User can operate with VSP1314 with local front panel and remote control with the software the default signal of layer 2, lights on yellow , it means
Preview outputs DVI2. Other signal keys light on red , user selects the signal key as needed, keys will light on run on the PC,remote control by RS232,USB or TCP/IP.
yellow as selected, tap TAKE button to change the
Local Control-Front Panel Operation
selected signal to Program output.
Step 1-Set Output Resolution
Press Menu/Effect , Rotate the knob to select Output
Program and Preview. About the Menu( Menu/Effect lights off) tap Menu/Effect, the key lights on green, tap again to enter Effect page, then the key lights on
Format ,Press knob to select Output Resolution.
Setting, Select the Output resolution via rotating the knob, rotate the knob again, Press Menu/Effect to the red, rotate the knob to select the needed effects of the model, There are four kinds of effects for user to homepage.
select: Wipe Hard, Wipe Soft, FADE, CUT。
Address:Rm.S603-604,Weiye Building ,Torch Hi-Tech Industrial Development Zone,Xiamen,
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http: //www.rgblink.cn
VSP 1314 Quick Start
Version1.0
Page 2 of 3
Step 3 SCALE Setting
2
PIP2 is 2/1 mode: Layer 2 is above Layer 1.
Press PIP2/PIP1, then the key turns red.
Press SCALE/CROP button, key lights on green to the
SCALE setup menu, when HSIZE/HPOS turns green, user can adjust HSIZE via rotate the knob, Tap
HSIZE/HPOS again,the key turns red which is the
HPOS adjusting state. Tap a third time, the key turns green again and it goes back to the HSIZE adjusting s t a t e . A n d t h e s a m e a d j u s t i n g w a y g o e s f o r
VSIZE/VPOS adjusting. When setup finished, tap
S C A L E / C R O P b u t t o n a n d i t g o e s b a c k t o t h e
V1 The play type of USB1 is video, it is the default mode . User can select Movie via MENU
USB Setting USB1 USB1 Play Type, and the sign will be showed on homepage.
V2
The play type of USB2 is video, it is the default mode . User can select Movie via MENU
USB Setting USB2 USB2 Play Type, and the sign will be showed on homepage.
h o m e p a g e , S C A L E / C R O P a n d HSIZE / HPOS ,
VSIZE/VPOS light off, function off.
P1 The play type of USB1 is image, it is the default mode . User can select Photo via MENU USB
Setting USB1 USB1 Play Type, and the sign will be showed on homepage.
function and VSIZE/VPOS function can’t be implemented at the same time .Adjust HSIZE/HPOS or else VSIZE/VPOS separately at one time for their keys cannot be lighted on together.
2.When SCALE/CROP functions off, tap HSIZE/
HPOS, then VSIZE/VPOS,when these two keys light on, set parameters of SCALE and CROP to the default value: FULLSCREEN functions on. Lights off when parameters are set.
3. DVI3 background signal can’t set SCALE when in non-mosaic mode .
Step 4-Save and Load
Press SAVE/LOAD: The key lights on green and enter
S A V E s t a t e , a l l o f CV1 / 1, CV2 / 2, USB1 / 3 ,
DVI1 / 4,VGA1 / 5 , CV3 / 6, CV4 / 7, USB2 / 8,
DVI2/9,VGA2/10 light on green, user can select and save. Saving finished, the selected key lights off, while other savings can still be implemented. At saving state, other functions cannot be implemented.
When savings finished ,tap this key again and the key t u r n s r e d t o e n t e r L O A D s t a t e , a l l o f
CV1 / 1,CV2 / 2,USB1 / 3 , DVI1 / 4,VGA1 / 5 , CV3 / 6,
CV4 / 7, USB2 / 8,DVI2 / 9,VGA 2 / 10 l i g h t o n r e d meaning the savings can be loaded. At the time other f u n c t i o n s c a n n o t b e i m p l e m e n t e d e i t h e r . T a p
SAVE/LOAD button again to exit LOAD function.
P2 The play type of USB2 is image, it is the default mode . User can select Photo via MENU
USB Setting USB2 USB2 Play Type, and the sign will be showed on homepage.
Background overlying .Select DVI3 via
B
MENU Output Background,and the sign will be showed on homepage.
B Background input setting.Select DVI3 via MENU
Input Input Matrix Channel3, and the
3
TP sign will be showed on homepage.
VSP 1314's maximum display and default working mode is 3 display layers.
Test Pattern. MENU Test Parrern,Then select scroll mode, return to the homepage can see The
mark.
Brack background input, this is the default configuration. Set the third layer of input matrix or output background as Black, return to the homepage can see the mark.
W
Draw curtain.This position was automatic/manual
ALPHA originally, It will show in here when open the mode. Operation: Enter EFFECT, select Effects
Mode as Wipe Hard, Wipe Soft mode, return to homepage can see the mark.
Splicing.Select ON via MENU Split Split
Switch,Return to homepage can see the mark.
Screen Windows Mode,Select Screen via MENU
NOTE
on SAVE1 mode when power on
VSP1314 .After factory reset ,all the user modes are initialized.
Factory reset: For fault parameter setting, user can go to the factory reset. Tap Menu/Effect button, rotate the knob, select the factory reset function, tap again to
F
OUTPUT Screen Windows Mode, return to homepage can see the mark.
Full Screen ,this is default mode or can select
FULL via MENU OUTPUT Scree confirm, factory reset is done.
Step 5-Color operation panel
Starting-up LOGO:Power on the
M
Windows Mode,return to homepage can see the mark.
Manual ALPHA.Press TAKE and rotate knob to adjust the indicator to another end,
Then return to homepage can see the mark.
d e v i c e a n d t h e i m a g e o n l e f t i s
A
Automatic ALPHA,this is the default mode. s h o w n o n L C D s c r e e n f o r t h e Or press TAKE ,then return to homepage can
1 initializing process.
PIP1 is 1/2 mode: Layer 1 is above Layer 2.
see the mark.
Coded lock.It means the device is locked.
Press PIP1/PIP2, and the key lights on green.
Address:Rm.S603-604,Weiye Building ,Torch Hi-Tech Industrial Development Zone,Xiamen,
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http: //www.rgblink.cn
VSP 1314 Quick Start
Version1.0
Page 3 of 3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project