advertisement
ASSEMBLY
MANUAL
cuisinart
®
Gourmet INFRARED 810
85-3110-8 (G53503) Propane
85-3111-6 (G53504) Natural Gas
REAd ANd SAvE MANUAL foR fUtURE REfERENcE.
Assemble your grill immediately.
Missing or damaged parts should be claimed within 30 days of purchase.
for product inquiries, parts, warranty and troubleshooting support, please call 1-800-309-3452.
www.cuisinartbbqs.com
LiMitEd 5-YEAR WARRANtY
Manual Revision #: 22092014 AT
H E A V Y A R T I C L E N E E D S 2 T O L I F T
THIS MANUAL MUST REMAIN WITH THE PRODUCT AT ALL TIMES
to oRdER non-warranty replacement parts or accessories, or to register your warranty, please visit us on the web at www.cuisinartbbqs.com
cAUtioN
Sharp edges. Wear gloves when assembling your grill.
cAUtioN
Read and follow all safety statements, assembly instructions, use and care directions before attempting to assemble and cook.
dANGER
1. if you smell Gas: a. Shut off gas to the appliance b. Extinguish any open flame c. open lid d. if odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department
2. do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance.
3. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
iNStALLER oR
ASSEMBLER/coNSUMER
this manual should be kept with the BBQ at all times.
WARNiNG
failure to follow all of the Manufacturer’s instructions could result in hazardous fires, explosions, property damage, or serious personal injury or even death.
follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. do not try lighting this BBQ without reading the Lighting instructions section of the
Safety and care Manual that accompanies this grill.
dANGER
1. do not store or use gasoline or other flammable liquids or vapours in the vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
cAUtioN
Avoid burns. the stainless steel and steel surfaces of this barbecue can become extremely hot, in direct sun and while the barbecue is in operation.
T H I S B A R B E C U E I S F O R O U T D O O R U S E O N LY cUiSiNARt
®
cUStoMER cARE HotLiNE
1-800-309-3452
HARDWARE PACK tools Needed for Assembly
• #2 Phillips screwdriver (long and short)
• ¼” Slotted screwdriver (long and short)
• Adjustable wrench
• Pliers
• Rubber Mallot
for correct hardware assembly, always position the lock washer between the screw and the flat washer.
Screw
Lock Washer
Flat Washer
No. Description
1 1/4-20UNCx38 Screw
8
9
6
7
10
11
12
4
5
2
3
1/4-20UNCx16 Screw
NO. 10-24UNCx13 Screw
ST4.2x10 Tapping Screw
ST4.2x20 Tapping Screw
φ7 Lock Washer
φ7 Washer
Fiber Washer
φ5 Lock Washer
φ5 Washer
Control Knob
U Pin
Part Number
20120-13038-250
20120-13016-250
20124-13013-250
22500-42010-137
22500-42020-137
41400-07000-250
40300-07000-250
G466-0042-9000
41400-05000-250
40300-05000-250
G618-0014-9000
G350-0026-9000
Qty.
8
26
22
4
12
12
2
1
18
12
6
1
Note: do not fully tighten all the nuts during this initial stage caution:
Sheet metal can cause injury. Wear gloves when installing this grill.
1
4
1/4-20UNCx38 Screw
X 8
ST4.2x10 Tapping Screw
X 6
2
1/4-20UNCx16 Screw
X 18
5
ST4.2x20 Tapping Screw
X 1
3
6
NO.10-24UNCx13 Screw
X 12
φ7 Lock Washer
X 26
7 8 9
φ7 Washer
X 22
Fiber Washer
X 4
φ5 Lock Washer
X 12
10 11 12
φ5 Washer
X 12
Control Knob
X 2
U Pin
X 1
BEFORE ASSEMBLING THE BARBECUE, READ THESE INSTRUCTIONS CAREFULLY.
Assemble the barbecue on a flat, clean surface. Grill is heavy. two people are recommended to complete assembly.
1
2
CK
CL
CM
CN
CO
CP
CQ
CG
CH
CI
CJ
CE1
CE2
CF1
CF2
CA
CB
CC
CD
BH
BI
BJ
BD
BE
BF
BG
BA1
BA2
BB
BC
BK
BL
BM
PARTS LIST (PROPANE) FOR 85-3110-8 (G53503)
Item No.
Qty. Description
AA
AB
AC
AD
AE
AF
AG
1
1
2
1
2
2
1
Top lid
Lid Handle
Lid Handle End Cap
Thermometer
Screw for Top Lid
Lid Bumper
Logo
Part No.
G535-2000-01
G535-0002-01
G358-0004-01
G512-0085-01
G359-0030-01
G527-0002-01
G618-0054-01
Item No.
Qty. Description
DE
DF
DG
DH
DI
DA
DB
DC
DD
DJ
DK
1
1
1
1
Side Shelf Table - Right
Side Shelf Fascia - Right
Infrared Support Frame
Infrared Zone Side Burner
Part No.
G535-0400-02
G535-0500-02
G535-3500-01
G614-8500-01
1 Electrode Set, Infrared Zone
1 Lid, Infrared Zone
G614-0092-01
G501-0070-02
1 Cooking Grate, Infrared Zone G525-0055-01
1 Infrared Grease Tray G614-0075-01
1 Infrared Side Burner Wind shield
G614-0073-01
1 Side Shelf Table - Left
1 Side Shelf Fascia - Left
G525-0600-01
G535-2500-01
1 Burner Box Assembly
1 Burner Box Surround
3 Main Burner
1 Carryover Assembly
3 Flame Tamer
3 Cooking Grate, Burner Box
1 Warming Rack
1 Stainless Steel Rotisserie
Burner
G535-3600-02
G535-1500-01
G525-3800-02
G535-0033-01
G525-0015-01
G525-0016-01
G525-0017-01
G535-3800-01
1 Electrode Set, Rotisserie
Burner
G453-0033-01
1 Wind Shield, Rotisserie Burner G501-00B1-01
1 Collector Box, Rotisserie
Burner
G501-00C1-01
1 Match Holder
1 Rotisserie LP Valve
2 Lid Support Pin
G501-0068-01
G535-0024-01
G525-0014-02
F1
F2
F3
F4
EE
EF
EG
EH
EI
EA
EB
EC
ED
1 Cart Side Panel - Left
1 Cart Side Panel - Right
1 Bottom Shelf - LP
2 Wheel with Lock
2 Wheel
1 Left Door Assembly
1 Right Door Assembly
2 Door Handle
4 Door Magnet Assembly
1 Hardware pack
1 Assembly Manual
1 Safety and Care Manual
1 Tank Screw
G535-0009-01
G525-0010-01
G535-0900-01
G350-0023-01
G350-0024-01
G535-2100-01
G535-2200-01
G517-0011-01
G501-00F2-03
G535-B003-01
G535-M003-01
G535-M003-02
G505-0047-01
1 Manifold Assembly - LP
1 Regulator
G535-1700-01
G510-0006-01
1 Infrared Side Burner Valve - LP G535-0023-01
2 Metal Hose G508-0024-01
1 Rotisserie Flexible Hose
1 Rotisserie LP Orifice
G601-0055-A1
G525-0057-01
1 Electronic Ignition Assembly G535-0032-01
1 Electronic Ignition Battery Cap G535-0031-02
3 Electrode Set, Main Burner
5 Control Knob
5 Bezel, Control Knob
1 Control Panel
1 Front Brace
1 Grease Tray
1 Upper Back Panel
1 Heat Shield
1 Left Track
1 Right Track
1 Lower Back Panel
G525-0030-01
G618-0014-01
G525-0012-01
G535-0008-01
G535-5000-01
G350-4400-01
G535-0013-01
G525-0022-01
G515-0024-01
G515-0025-01
G535-0012-01
EXPLODED DIAGRAM (PROPANE)
FOR 85-3110-8 (G53503)
BI
BJ
BH
BC
BB
BG
BF
BE
BD
AA
AD
AG
AE
AF
BA2
BM
BA1
AC
AB
AC
CN
DF
DE
DC
DA
DH
DD
DG
CE1
CE2
CA
BL
CD
CQ
DK
CG
CD
CC
BM
CB
DJ
CF2
CF1
CK
CM
CO
CL
CP
CJ
BK
EH
CI
CH
DB
DI
EG
EH
EA
EC
EB
ED
EF
EI
EI
EE
Hardware
Pack
f1
EXtRAS
Assembly
Manual
f2
Safe Use
& Care
Manual
f3
Tank
Screw
f4
3
4
CK
CL
CM
CN
CO
CP
CQ
CG
CH
CI
CJ
CE1
CE2
CF1
CF2
CA
CB
CC
CD
BH
BI
BJ
BD
BE
BF
BG
BA1
BA2
BB
BC
BK
BL
BM
PARTS LIST (NATURAL GAS) FOR 85-3111-6 (G53504)
Item No.
Qty. Description
AA
AB
AC
AD
AE
AF
AG
1
1
2
1
2
2
1
Top lid
Lid Handle
Lid Handle End Cap
Thermometer
Screw for Top Lid
Lid Bumper
Logo
Part No.
G535-2000-01
G535-0002-01
G358-0004-01
G512-0085-01
G359-0030-01
G527-0002-01
G618-0054-01
Item No.
Qty. Description
DE
DF
DG
DH
DI
DA
DB
DC
DD
DI
DJ
1
1
1
1
Side Shelf Table - Right
Side Shelf Fascia - Right
Infrared Support Frame
Infrared Zone Side Burner
Part No.
G535-0400-02
G535-0500-02
G535-3500-01
G614-8500-01
1 Electrode Set, Infrared Zone
1 Lid, Infrared Zone
G614-0092-01
G501-0070-02
1 Cooking Grate, Infrared Zone G525-0055-01
1 Infrared Grease Tray G614-0075-01
1 Infrared Side Burner Wind shield
G614-0073-01
1 Side Shelf Table - Left
1 Side Shelf Fascia - Left
G535-0600-01
G535-2500-01
1 Burner Box Assembly
1 Burner Box Surround
3 Main Burner
1 Carryover assembly
3 Flame Tamer
3 Cooking Grate, Burner Box
1 Warming Rack
1 Stainless Steel Rotisserie
Burner
G525-3600-02
G535-1500-01
G525-3800-02
G535-0033-01
G525-0015-01
G525-0016-01
G525-0017-01
G535-3800-01
1 Electrode Set, Rotisserie
Burner
G453-0033-01
1 Wind Shield, Rotisserie Burner G501-00B1-01
1 Collector Box, Rotisserie
Burner
G501-00C1-01
1 Match Holder
1 Rotisserie NG Valve
2 Lid Support Pin
G501-0068-01
G535-0028-01
G525-0014-02
EE
EF
EG
EH
EI
EA
EB
EC
ED
F1
F2
F3
1 Cart Side Panel - Left
1 Cart Side Panel - Right
1 Bottom Shelf - NG
2 Wheel with Lock
2 Wheel
1 Left Door Assembly
1 Right Door Assembly
2 Door Handle
4 Door Magnet Assembly
1 Hardware pack
1 Assembly Manual
1 Safety and Care Manual
G535-0009-01
G535-0010-01
G535-3400-01
G350-0023-01
G350-0024-01
G535-2100-01
G535-2200-01
G517-0011-01
G501-00F2-03
G535-B003-01
G535-M003-01
G535-M003-02
1 Manifold Assembly - NG
1 Natural Gas Hose
G535-2800-01
G501-0099-01
1 Infrared Side Burner Valve - NG G535-0027-01
2 Metal Hose G508-0024-01
1 Rotisserie Flexible Hose
1 Rotisserie NG orifice
G601-0055-A1
G512-0048-01
1 Electronic Ignition Assembly G535-0032-01
1 Electronic Ignition Battery Cap G535-0031-02
3 Electrode Set, Main Burner
5 Control Knob
5 Bezel, Control Knob
1 Control Panel
1 Front Brace
1 Grease Tray
1 Upper Back Panel
1 Heat Shield
1 Left Track
1 Right Track
1 Lower Back Panel
G525-0030-01
G618-0014-01
G525-0012-01
G535-0008-01
G535-5000-01
G350-4400-01
G535-0013-01
G525-0022-01
G515-0024-01
G515-0025-01
G535-0012-01
EXPLODED DIAGRAM (NATURAL GAS)
FOR 85-3111-6 (G53504)
BI
BJ
BH
BC
BB
BG
BF
BE
BD
AA
AD
AG
AE
AF
BA2
BM
BA1
AC
AB
AC
CN
DF
DE
DC
DA
DH
DD
DG
CE1
CB
CE2
CA
BL
CD
CG
CD
CC
BM
DJ
CQ
DK
CF2
CF1
CK
CM
CO
CL
CP
CJ
BK
EH
CI
CH
DB
DI
EG
EH
EA
EC
EB
ED
EF
EI
EI
EE
Hardware
Pack
f1
EXtRAS
Assembly
Manual
f2
Safe Use
& Care
Manual
f3
5
6
ASSEMBLY INSTRUCTIONS
1.
EE
Ed
A
Back view
Ec
EE
Separate the 2 different types of wheels, 2
Locking Wheels (ED) and 2 Regular Wheels
(EE).
Insert the U Pin (#12) into one of the Regular
Wheels (EE), as shown in image B. Attach the
Regular Wheel (EE) to the front of the Bottom
Shelf (EC), and use the U Pin (#12) to secure and tighten.
Repeat for remaining 3 Wheels (EE & ED).
NotE: Regular Wheels (EE) need to be assembled to the front of the Bottom
Shelf (EC), and Wheels with Lock (ED) need to be assembled to the back of the Bottom Shelf (EC), as shown in image A.
YoU WiLL NEEd:
12
B
Close up
X 1
2.
EB
a. Ensure that the wheels are firmly locked in
the “ON” position before continuing. b. Assemble the Left Cart Side Panel (EA) and
the Right Cart Side Panel (EB) to the Bottom
Shelf (EC).
EA
Ec
YoU WiLL NEEd:
6
A
Front view
7
X 6 X 6 X 6
EB
Ec
B
Close up
ASSEMBLY INSTRUCTIONS
2.
cQ
EB
EA c
Ec
c. Assemble the Lower Back Panel (CQ)
to the Left Cart Side Panel (EA) and Right
Cart Side Panel (EB).
YoU WiLL NEEd:
6 7
X 4 X 4 X 4
tiP: The top of the lower back panel (CQ) can be identified by the four recesses located on the top of this part.
3.
EB
A
Back view
d cQ
Close up
EB cK cJ cQ
EA
Attach the Front Brace (CK) to the Left and
Right Cart Side Panels (EA and EB).
tiP: One person should align the left side, while the second person assembles the right side.
YoU WiLL NEEd:
6 7
EA
X 2 X 2 X 2
tiP: The bottom of the front brace (CJ) can be identified by the four recesses located on the bottom of this part.
B
Close up
7
ASSEMBLY INSTRUCTIONS
4.
A+B tHiS StEP REQUiRES 3 PEoPLE. do Not AttEMPt ALoNE. EXtREMELY
HEAvY.
a. Position the Top Lid and Burner Box
Assembly (A and B) onto Cart Assembly (C), as shown.
A
Front view
c
Close up - left outside view
A+B
EB
B
Back view
8
c
Front view
EA cK
EB
EA
b. Assemble Burner Box Assembly (A and B) to the Left and Right Cart Side Panels (EA and
EB), as shown.
YoU WiLL NEEd:
6 7
X 4 X 4 X 4 c. Assemble the front of the Burner Box
Assembly (A and B) to the Front Brace (CK), as shown.
YoU WiLL NEEd:
6 7
X 2 X 2 X 2
ASSEMBLY INSTRUCTIONS
5.
cM
EB
A
Back view
EA
Attach the Upper Back Panel (CM) to both the
Left and Right Cart Side Panels (EA and EB).
Only install hardware in the bottom portion of the Upper Back Panel (CM), as shown in figure
B.
do Not tiGHtEN ScREWS UNtiL SidE
SHELf HAS BEEN iNStALLEd.
YoU WiLL NEEd:
6 7
X 2 X 2 X 2
6.
dJ cM
B
Close up
EA
BA
A dK
Front, left side view
dK
B
View inside burner box
dJ
a. Open the Lid. Assemble the Left Side Shelf
Assembly (DJ and DK) to the Cart Assembly by inserting the Side Shelf Tabs into holes on the Cart Assembly (figure A).
BA
b. Secure using hardware, as shown in figure B,
C & D.
YoU WiLL NEEd:
6 8
X 2 X 2 X 2
9
10
ASSEMBLY INSTRUCTIONS
6.
dJ
BA c
View under left side shelf (back)
dK
YoU WiLL NEEd:
6
X 1 X 1
dJ
YoU WiLL NEEd:
9
BA
7.
d
View under left side shelf (front)
BA dA dK
7
X 1
10
X 3 X 3 X 3
NotE: Beware of sharp edges.
a. Open the lid. Assemble the Right Side Shelf
Assembly (DA and DB) to the Cart Assembly by inserting the Side Shelf tabs into the holes on the Cart Assembly (figure A).
A
Front, right side view
dB
Close up
ASSEMBLY INSTRUCTIONS
7.
dA
BA
B
View inside burner box
dB
b. Secure using hardware, as shown in figure B,
C and D.
YoU WiLL NEEd:
6 8
X 2 X 2 X 2
dA
YoU WiLL NEEd:
6
X 1 X 1
7
X 1
dc c
BA
View under right side shelf (back)
dB dc
YoU WiLL NEEd:
9 10
X 3 X 3 X 3
NotE: Beware of sharp edges.
d
View under right side shelf (front)
BA
11
ASSEMBLY INSTRUCTIONS
8 .
dA cc dB
A
Front, right side view
dB dA cc
11
9.
B
Front, right side view
di dc
A
Front, right side view a. Remove the hardware that is pre-assembled to the Side Burner Valve bracket (CC), as shown in figure A. b. Insert the Side Burner Valve stem (CC) through the rear of the Right Side Shelf
Fascia (DB). Assemble the Side Burner Valve
(CC) to the Side Shelf Fascia (DB), using the hardware removed (figure A).
c. Assemble the Side Burner Control Knob
(#11) to the Side Burner Valve (CC) (figure B).
YoU WiLL NEEd: di
X 1 a. Assemble the Infrared Side Burner Wind
Shield (DI) to the Infrared Support Frame
(DC), as shown in figure A and B.
YoU WiLL NEEd: dc
X 2
NotE: Two people recommended.
12
B
View from above right side shelf
ASSEMBLY INSTRUCTIONS
9 .
dd dc c
Front, right side view b. Position the Infrared Zone Side Burner (DD) through the opening in the Infrared Support
Frame (DC).
c. Make sure that the Infrared Zone Side Burner
(DD) engages the Side Burner Valve (CC) gas jet, as shown in figure D.
cc dd d
View from underneath right side shelf
dc dd
E
View from above right side shelf
dd dE f
View from above right side shelf
dc
d. Assemble the Infrared Zone Side Burner (DD) to the Infrared Zone Support Frame (DC), at the 2 points indicated in figure E.
YoU WiLL NEEd:
9 10
X 2 X 2 X 2 e. Feed the Infrared Zone Electrode set (DE) from underneath the Infrared Zone Side
Burner (DD), through the small opening on the left side of the Infrared Zone Support
Frame (DC). Align and assemble the electrode using the self tapping screw provided, as shown in figure F.
YoU WiLL NEEd:
5
X 1
13
ASSEMBLY INSTRUCTIONS
9 .
dG dc
G
Front, right side view f. Position the Infrared Zone Cooking Grate
(DG) on the Infrared Zone Support Frame
(DC).
g. Insert the Infrared Grease Tray (DH) into the back of the Infrared Zone Support Frame
(DC), as shown.
14
dc
10.
H
Back, right side view
cf1
Plastic Nut cf2 dH
a. Remove the Electronic Ignition Battery Cap
(CF2) and the plastic nut from the Electronic
Ignition Assembly (CF1).
A dJ cf1
B
View under left side shelf
cf2 dK
Plastic Nut
b. Feed the Electronic Ignition Assembly (CF1) through the opening in the Left Side Shelf
Fascia (DK) and secure using the nut.
ASSEMBLY INSTRUCTIONS
10.
dJ d dK c
Front, left side view
-
+ cf2
c. Insert one “AA” battery into the battery compartment with the positive end facing outward, as shown. Secure using the
Electronic Ignition Battery Cap (CF2).
dJ dK
tiP: The Electrode set for Main Burner (CG), the Electrode wire for Infrared Zone (DE), the Electrode wire for Rotisserie Burner
(BH) can be found fastened together with the Rotisserie Valve (BL) hanging from the left side of Control Panel on the outside of the burner box (BA), as shown.
BL d
BA
View under left side shelf
cf1 cG dE cG
BH
E cf1
d. Insert all Electrode wires (CG, DE, BH) into the Electronic Ignition Assembly (CF1), as shown in figure E.
NotE: All electrode wire connection points are the same size.
15
16
ASSEMBLY INSTRUCTIONS
11.
BL
A
Front, left side view
dK
a. Remove the hardware that is pre-assembled to the Rotisserie Valve bracket (BL), as shown in figure A. b. Insert the Rotisserie Burner Valve stem
(BL) through the rear of the Left Side Shelf
Fascia (DK). Assemble the Rotisserie Valve
(BL) to the Side Shelf Fascia (DK), using the hardware removed (figure A).
dK
B
Front, left side view
BL
11
c. Assemble the Control Knob (#11) to the
Rotisserie Valve (BL).
YoU WiLL NEEd:
X 1
ASSEMBLY INSTRUCTIONS
12.
cM cN
A
Back view
cN
Close up, back
cM
a. Position the Heat Shield (CN) into the two hooks located on the bottom of the Upper
Back Panel (CM), as shown in figure A. b. Assemble the Heat Shield (CN) to the bottom of the Front Brace (CK), as shown in figure B.
YoU WiLL NEEd:
X 2
B
Front view
cK cN cK cN
Close up, front
17
18
ASSEMBLY INSTRUCTIONS
13.
cK
EA
A
Front view
co cP
EB
a. Assemble the Left and Right Tracks (CO and
CP) for the Grease Tray (CL), as shown in figure A-C.
b. Both the Left and Right Tracks (CO and CP) should be inserted into the two clips located on the Upper Back Panel (CM), as shown in figure B.
co cM cP
B
Close up, back
cK co c
Close up, front
cP
c. Assemble the front of the Left and Right
Tracks (CO and CP) to the Front Brace (CK), as shown in figure C.
YoU WiLL NEEd:
X 2 d. Insert the Grease Tray (CL) into the opening of the Upper Back Panel (CM).
cL d
Back view
cM
ASSEMBLY INSTRUCTIONS
14.
EH
EG
A
15.
Assemble the Door Handle (EH) to the Left and
Right Door Assembly (EF and EG) as shown in figure A.
YoU WiLL NEEd:
9 10
X 4 X 4 X 4 a. Assemble the Right Door Assembly (EG), to the Bottom Shelf (EC) by inserting the fixed pin (bottom of door) into the hole provided
(figure B).
Ec
EG
A c
Top of door
cK
B
Bottom of door
Ec
EG
b. Assemble the top of the Door Assembly (EG) to the Front Brace (CK), by pressing in the door support pin and aligning with the hole located on the top right corner of the door.
tiP: Use a paint scraper to press-in the support pin, while the second person aligns the door. The support pin will lock into position when the door is assembled correctly. c. Repeat steps a and b for the Left Door
Assembly (EF).
EG
19
ASSEMBLY INSTRUCTIONS
16.
Bd
Place the Flame Tamers (BD) into the Burner
Box (BA).
17.
BE
a. Place the Cooking Grates (BE) into the
Burner Box (BA), as shown.
20
18.
A
Bf
BA
b. Assemble the Warming Rack (BF) by inserting the fixed pins into the warming rack support bars located on the Burner Box (BA), as shown in figure A and B.
B
Close up
ASSEMBLY INSTRUCTIONS
19.
A
B cB
EB
Ec f4 foR PRoPANE ModELS oNLY.
for natural gas model, follow step 20.
a. Position the Regulator Hose (CB) through the hole in the Right Side Panel (EB).
b. Position the 20 lb propane tank onto the
Bottom Shelf (EC), and secure using the
Bolt (F4) (already attached) located on the underside of the Bottom Shelf, as shown in figure B. c. Attach the regulator coupling nut to the LP cylinder valve. Be careful not to cross thread.
Hand tighten only.
d. Perform Leak Test. See page 5 of the
Cuisinart
®
Safety and Care Manual.
AttENtioN: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the
Cuisinart
®
Safety & Care Manual.
All Safety and Leak test MUSt BE
PERfoRMEd BY tHE ENd USER, prior to lighting this BBQ.
WARNiNG do not store extra propane tanks within BBQ cart.
21
22
ASSEMBLY INSTRUCTIONS
20 .
cB cc foR NAtURAL GAS ModEL oNLY.
a. Attach the Natural Gas Hose (CB) to the Side
Burner Valve (CC) as shown. b. Perform Leak Test. See page 6 of the
Cuisinart
®
Safety and Care Manual.
AttENtioN: In order to complete installation of your Natural Gas BBQ a 1/2” or 3/8” adapter may be required to connect your BBQ’s Natural Gas hose to your home gas supply.
Contact your Natural Gas supplier to purchase the necessary part.
AttENtioN: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the
Cuisinart
®
Safety & Care Manual.
All Safety and Leak test MUSt BE
PERfoRMEd BY tHE ENd USER, prior to lighting this BBQ.
visit www.cuisinartbbqs.com to complete product registration.
cuisinart
®
Gourmet Barbecues customer Service:
1-800-309-3452
Join the conversation
facebook.com/cuisinartbbqs twitter.com/cuisinartbbqs
Cuisinart
®
is a registered trademark used under license
© 2015 Trileaf Distributions Trifeuil
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement